Desa CGESBMR User Manual

27" MODELS CGESBL AND VESBL

18" MODELS CGESBMR AND VESBMR

ELECTRIC STOVE WITH REMOTE CONTROL

SAFETY INFORMATION AND OPERATION MANUAL

Read these instructions completely before operating

electric stove. Failure to follow them could cause a

heater malfunction resulting in serious injury and/or

property damage.

Save this manual for future reference.

For more information, visit www.desatech.com

SAFETY INFORMATION

PRODUCT DIMENSIONS &

SPECIFICATIONS

Continued

12. Always disconnect the unit from the power

supply before performing any cleaning, light

bulb replacement, maintenance, relocating the

heater or when the unit is not in use for long

periods of time.

15"

27"

13. When transporting or storing the unit, keep

it in a dry location, free from dust, excessive

vibration or other factors, which may damage

the unit.

26"

LISTING APPROVALS

This heater has been tested in accordance with the

CSA Standards for ﬁxed and location-dedicated

electric room heaters in the United States. All

components are UL or CSA safety certiﬁed.

CGESBL/VESBL Remote Controlled

27" Electric Stove

Ifyouneedassistanceduringinstallation,pleasecon-

tact your local dealer or the DESAHeating Products

Technical Services Department at 1-866-672-6040.

12.5"

18"

UNPACKING AND

TESTING THE UNIT

25.25"

Carefully remove the unit from the box. Prior to

permanently installing the unit, test to make sure

the unit operates properly by plugging the power

supply cord into a conveniently located 120-volt

grounded outlet.

CGESBMR/VESBMR Remote Controlled

18" Electric Stove

CAUTION: The unit's power

supply cord must be connected

to a properly grounded and pro-

tected 120-volt outlet. Always

use ground fault protection

where required by the electri-

cal code.

Figure 1 - Heater Dimensions

Frequency

60 Hz

Heater Power 1500 W

Heater Output 5000 BTUs

Power Supply 120V; 15 Amp

Grounded, Circuit

WARNING: Do not operate

the unit if it is damaged or has

malfunctioned.Ifyoususpectthe

unit is damaged, return the unit

to an authorized service facility

for examination, electrical or me-

chanical adjustment or repair.

Note: A dedicated power supply circuit is recom-

mended for the unit but not required. Additional

electrical appliances on the same circuit may ex-

ceed the current (amperage) rating for that circuit.

If after the installation of your unit, the circuit

breaker trips or the fuse fails on a repeated basis,

then a dedicated circuit will likely be required.Any

new wiring must be done in compliance with local

and national codes and other applicable regula-

tions in order to reduce the risk of ﬁre, electric

shock or other injuries. Therefore, it is strongly

recommended that you hire a licensed electrician

to complete any such work.

117190-01B

www.desatech.com

3. Heater Switch and Control Dial: The heater

switch has a sun directly below it. To turn the

heateron,ﬂiptheHeaterSwitchtoONposition

(the"|"indicatesONand"O"indicatesOFF).

The Control Knob has a thermometer below

it. Turn the dial clockwise past the number 8.

Youshouldhearasmallclickingsoundindicat-

ing the heater has started and heat will emit

throughventslocatedatthebottomoftheunit.

To turn off heater, turn the temperature dial

counter clockwise past number 1 and ﬂip the

HeaterSwitch to OFFposition. Heat will stop

coming out of the vent.

GROUNDING

INSTRUCTIONS

This stove is for use on 120 volts. The cord has a

plug as shown in Figure 2. An adapter is available

for connecting three-blade grounding-type plugs

to two-slot receptacles. The green grounding lug

extending from the adapter must be connected to

a permanent ground such as a properly grounded

outlet box. The adapter should not be used if a

three-slot grounded receptacle is available.

To increase the desired temperature, turn

the temperature dial clockwise towards

Number 8.

Todecreasethedesiredtemperature,turnthe

temperature dial counter clockwise towards

number 1. The heater has a built-in thermo-

stat so it will shut off automatically once the

settemperatureisreached.Itwillalsoturnon

automaticallyifthe roomtemperature drops

below the set temperature on the dial.

Adapter

Grounding Pin

Figure 2 - Grounding Methods

OPERATING

Note: When the heater is turned on for the

ﬁrst time, it may release a slight, harmless

odor.Thisodorisanormaloccurrencecaused

by the initial heating of the internal heating

elements and should not occur again.

INSTRUCTIONS

Once the unit has been properly connected to a

ground electrical outlet, it is ready to operate.

Note: Ensure the circuit breakers for power

supply are turned on.

4. Flame Control Dial: This dial controls the

intensity of the ﬂame.

CONTROL PANEL OPERATION

Controls are located on the back of the unit

(see Figure 3).

Flame Control Dial Main Power Switch

1. Main ON/OFFpower switch: This switch is

located at the furthest right corner on the

control panel when looking at the back of

the unit. Turn the switch to ON and unit

will be ready to operate. The "|" indicates

ON and "O" indicates OFF.

Heater Switch

Heat Control Dial

IMPORTANT: Once you turn

the main switch to the ON posi-

tion, the remote control can no

longer be used. In order to use

the remote control, you must

keep the main ON/OFF switch

in the OFF.

Display Dial

Figure 3 - Electric Stove Control Panel

OPERATING BY REMOTE CONTROL

1. Plug in your electric ﬁreplace and it will

beep once. This means you have power

and your remote is ready to operate your

electric ﬁreplace.

IMPORTANT: To control the

electric ﬁreplace by remote, the

Main ON/OFF power switch on

the ﬁreplace must be in the OFF

position; the remote control will

NOT work if the manual ON/OFF

switch is in the ON position.

2. Display ON/OFFDial: There is a ﬂame icon

directly below this dial and it is the knob

at. After you turn the Main Power switch

to the ON position, turn the Display Dial

to desired setting. Both the logset and the

ﬂame will light up inside the ﬁreplace

www.desatech.com

117190-01B

5. Heater Button: To activate the heater,

press the heater button, then press HI,

MED or LO. The heater is per-set to the

following temperatures:

OPERATING

INSTRUCTIONS

Continued

HIGH will shut off when room reaches

approximately 86° F (30 C)

2. When operating the remote control, it must

be pointed at the logset inside the electric

stove and a beep must be heard each time

you press a function button. The beep con-

ﬁrms the remote control is performing the

function you have requested. Note: Make

sure your batteries are fully charged and

installed correctly in your remote control.

MED will shut off when room reaches ap-

proximately 75° F (24 C)

LO will shut off when room reaches

approximately 64° F (18 C)

6. To adjust the intensity of the flame,

press the two buttons labeled HIGH-

ER and LOWER under FLAME.

3. POWER ON/OFF button at the top left is

the main ON/OFF power button. Pressing

this button you will hear a beep; this acti-

vates the power to the unit. Note: If the

ﬂame does not come immediately, press the

DISPLAY ON/OFF button.

Toincreasetheﬂameintensity,pressand

release the HIGHER button. Each time you

press the button you will hear a beep and the

sizeoftheﬂamewillincreaseslightlyuntilthe

maximum setting is reached.

4. The two LOGSET buttons control

the brightness of ember bed, which

changes the brightness of your logset.

To increase the brightness, press and re-

lease the BRIGHTER button. Each time

you press this button you will hear a beep,

and the brightness will increase by a small

amount, until the maximum is reached.

To decrease the ﬂame intensity, press

and release the LOWER button. Each time

you press this button you will hear a beep

and the size of the ﬂame will decrease slight-

ly until the minimum setting is reached.

7. To use the stove as a heater without the

ﬂame, press the LOGSET DISPLAY ON/

OFF button to turn the ﬂame off and press

the HEATER ON/OFF button to turn the

heater on (if the heater was in the OFF

position). Press the LOGSET DISPLAY

ON/OFF button again to turn the ﬂame

back on. Press HEATER ON/OFF button

again to turn the heater off.

To decrease the brightness, press and release

the DIMMER button. Each time you press

this button you will hear a beep and the

brightness will decrease by a small amount,

until the minimum brightness is reached.

Infrared

Ray Exit

Note: You may have to re-adjust your

desired ﬂame setting (see step 6).

POWER

8. To turn off the stove, press the POWER ON/

OFF button once. When you hear the beep,

the ﬁreplace will be completely off and the

ﬂame will disappear. When you restart the

ﬁreplace with the remote control, all of the

features you had set will remain in effect.

Indicator

Light

ON/OFF

DISPLAY

Dimmer

EMBERS/

LOGSET

Brighter

HEATER

ON/OFF

TEMP. CONTROL

NOTICE:This remote control must remain

within 8 meters or 26 feet of the ﬁreplace to

be effective.

HIGH

MED

LOW

FLAME

HIGHER

LOWER

IMPORTANT: If the ﬂame does not acti-

vate after the POWER ON/OFF button

is pressed, press the DISPLAY ON/OFF

button to activate the ﬂame. If the ﬂame

does not appear, repeat step 4, page 8.

Figure 4 - Remote Control For Electric

Fireplace

117190-01B

www.desatech.com

Removing Top of Unit

1. Unplug unit from the power supply.

CLEANING AND

MAINTENANCE

2. Remove the two screws at the rear of the unit

which secure the top to the back frame.

WARNING: Always discon-

nect power and allow the heater

to cool before performing any

cleaning,maintenanceorreloca-

tion of this heater. Turn controls

to OFF and remove plug from

outlet or turn off circuit breaker

to heater.

3. Two clips hold the top to the sides. Push the

top of the unit toward the back until the clips

disconnect. Remove top of the unit and place

face up on the ﬂoor.

4. Unscrew the 4 screws from the metal plate

and set plate aside.

Turn off heater and circuit breaker to heater before

performing any cleaning and/or maintenance. Al-

low heater to cool completely.

Figure 5 - Stove Top Removal

Replacing Top Contrasting Bulb

BULB REPLACEMENT

1. The housing for the top contrasting light is

connected to the top of the mirror. Remove

housing from mirror by gently lifting up.

WARNING: The halogen light

bulbs in your unit can become

extremely hot. Allow at least 10

minutes between turning off the

heater and removing the light

bulbs to avoid accidental burns.

CAUTION: Do not force the

lighthousingoffthemirror. This

may damage the mirror (e.g.

chipping, cracking, etc.)

There are a total of 7 ( halogen light bulbs (type

GX6.35 rated 120 volts, 35 watts) in your unit.

2. Remove screws from each side of housing.

3. Carefully reach into the housing and remove

spring clip. Hold socket and pull out the old

bulb.

•

2 bulbs provide illumination for the ember bed

beneath the log set

2 bulbs provide illumination for the flame

generation assembly

3. Hold socket and push in new bulb (DO NOT

exceed wattage). Replace spring clip.

1 bulb provides illumination for the top con-

trasting light

4. Set aside until all bulbs have been changed.

2 bulbs for replacement

Front of Stove

Most halogen light bulbs are rated to last approxi-

mately 1800 hours. Like all light bulbs, halogen

bulbs require periodic replacement. When the

bulbs in your unit have burned out you will notice

or more of the following:

•

Contrasting light is dark

Flame is dim or dark in certain areas

Log set ember bed appears dim or dark in

certain areas

Screw

Mirror

Housing

Figure 6 - Removing Housing and Top

Contrasting Bulb

WARNING: Do not install

replacement bulbs that exceed

speciﬁed maximum watts.

Your unit must be opened in order to replace the

light bulbs. To reduce the number of times you

need to open the unit, replace all bulbs at the

same time.

www.desatech.com

117190-01B

2. Locate the ﬂame generation cylindrical drum.

It is constructed of two removable halves; ei-

ther of which can be removed from the unit.

CLEANING AND

MAINTENANCE

Continued

2. Squeeze half of drum cylinder until it's top

edge clears the top drum track. Remove bot-

tom edge of cylinder drum from bottom drum

track. This will give you access to the light

bulbs. Note: Do not exert excessive pressure

on drum cylinder as this may cause damage.

Replacing Log Set Ember Bed Bulbs

1. Carefully remove mirror from unit by lift-

ing it gently from the stove. Store in a safe

place or lay it face down on the carpet.

2. From the bottom, lift up the log set ember bed

and remove it from the unit (do not pull up on

logs).

3. Remove spring clip. Hold socket and pull out

old bulb.

3. Remove spring clip from bulb. Hold socket

and pull out old bulb.

4. Hold socket and push in new bulb (DO NOT

exceed wattage). Replace spring clip.

4. Hold socket and push in new bulb. Replace

spring clip.

5. Repeat steps 5 and 6 for second bulb.

6. Insertbottomedgeofremovedcylinderhalfinto

bottom drum track. Gently squeeze drum cylin-

der until it's top edge ﬁts into top drum rack.

5. Repeat steps 2 and 3 for the second bulb.

Bulb with

Spring Clip

7. Replace the metal plate with screws.

8. Replace the log set ember bed.

Bulb with

Spring Clip

Log Grate

9. Replacethemirror.Note:Beforereplacing,clean

mirror of any dust or ﬁngerprints. Make sure the

mirror side is toward the front of the unit.

10. Replace the top contrasting light housing.

Note: The contrasting light should be placed

at the mid point of the mirror edge.

11. Replace the metal plate and 4 screws. Replace

the top of the unit by sliding the top forward

until the clips reconnect.

12. Secure the top to the back frame by reattach-

ing screws.

Figure 7 - Ember Bed Bulb Replacement

(Looking in from Top of Unit)

Flame Cylinder Drum

Replacing Flame Generation Bulbs

1. Unscrew the 6 screws from back of stove

shown in Figure 8. Remove metal plate.

AVOID STRESS TO THE WIRES.

Figure 9 - Flame Generation Cylinder

Drum

Grounding

Connecting Screw

Screws

Figure 8 - Locating Flame Generation

Cylinder

117190-01B

www.desatech.com

CLEANING AND

TECHNICAL SERVICE

You may have further questions about your elec-

tric stove. If so, contact DESA Heating Productsʼ

Technical Service Department at 1-866-672-6040.

When calling please have your model and serial

numbers of your heater ready.

MAINTENANCE

Continued

CLEANING FRONT PANEL GLASS

WARNING: When cleaning

unit, the power supply should

be disconnected and the unit

should be cool.

You can also visit DESAHeating Productsʼtechni-

cal services web site at www.desatech.com.

REPLACEMENT PARTS

Note: Use only original replacement parts. This

will protect your warranty coverage for parts

replaced under warranty.

Over time the front glass panel may become dirty or

dusty. Dust can be removed by lightly rubbing the

glass surface with a clean, lint free cloth or paper

towel. To remove ﬁngerprints or other marks, use

a damp cloth with a good quality household glass

cleaner. The front glass panel should be completely

dried with a clean, lint free cloth or paper towel.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If

they canʼt supply original replacement part(s),

call DESA Heating Productsʼ Technical Service

Department at 1-866-672-6040.

When calling DESA Heating Products, have ready

CAUTION: Do not use abra-

sivecleanersonglasspanel.Do

not spray liquids directly onto

any surface of the unit.

•

your name

your address

model and serial numbers of your heater

how heater was malfunctioning

purchase date

WARNING: An authorized

service representative should

perform any other servicing.

Usually, we will ask you to return the part to the

factory.

PARTS NOT UNDER WARRANTY

Contactauthorizeddealersofthisproduct.Iftheycanʼt

supplyoriginalreplacementpart(s),callDESAHeating

Products at 1-866-672-6040 for referral information.

STORAGE

When not in use, unplug the unit from the power

supply and store in dry, dust free location.

When calling DESA Heating Products, have ready

•

model number of your heater

the replacement part number

www.desatech.com

117190-01B

TROUBLESHOOTING

WARNING: Turn off appliance and let cool before servicing. Only

a qualiﬁed service person should service and repair heater.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Stove turns off and will not 1. Stovehasoverheatedandsafe- 1. Reset switch by turning main

turn on

ty devise has cause thermal

switch to disconnect or home

circuit breaker has opened

power switch off and waiting 5

minutes then turning it back on

Flame is not moving

1. Loose wiring

1. Inspect wiring for loose con-

nections

2. Flame motor defective

2. Call a qualiﬁed service techni-

cian to replace ﬂame motor

Dim or poorly visible ﬂame

1. Bulb(s) are burnt out

2. Wiring is loose

1. Inspect bulbs and replace if

necessary

2. Inspect wiring for loose con-

nections and repair or replace

if necessary

Log set and/or ember is not 1. Bulb(s) are burnt out

glowing

1. Inspect bulbs and replace if

necessary

Flame sputters

1. Flame motor is defective

1. Low batteries

1. Call a qualiﬁed service techni-

cian to replace ﬂame motor

Remote control does not work

1. Replace AA batteries in re-

mote control

2. Unit switch and/or wall 2. Turn off main power switch

switch in ON position

(see Figure 3)

117190-01B

www.desatech.com

NOTES

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

www.desatech.com

117190-01B

NOTES

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

_____________________________________________________

______________________________________________________

117190-01B

www.desatech.com

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these speciﬁcations at any time without notice. The only warranty applicable is our

standard written warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

ELECTRIC STOVE

DESAHeating Products warrants this product to be free from defects in materials and components for one (1) year

from the date of ﬁrst purchase (excluding bulbs and fuses), provided that the product has been properly installed,

operated and maintained in accordance with all applicable instructions. To make a claim under this warranty the

Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required

to restore this heater to proper operating condition (excluding bulbs and fuses) and an allowance for labor when

provided by a DESA Heating Products Authorized Service Center. Warranty part(s) MUST be obtained through

authorized dealers of this product and/or DESA Heating Products who will provide original factory replacement

parts. Failure to use original factory replacement parts voids this warranty. The heater MUST be installed by a

qualiﬁed installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts

that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by

improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to

repairing a defective heater will be the responsibility of the owner.

TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE

OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED

WARRANTIESAND LIMITS THE DURATION OFANYAND ALL IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITYAND FITNESS FORAPARTICULAR PURPOSETO ONE (1)YEAR

ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA HEATING PRODUCTSʼ

LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA HEAT-

ING PRODUCTS SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING

INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of

incidental or consequential damages, so the above limitation on implied warranties or exclusion or limitation on

damages may not apply to you.

This warranty gives you speciﬁc legal rights and you may also have other rights that vary from state to state.

For information about this warranty write:

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

117190-01

117190 01

Rev. B

NOT A UPC

07/05

HP Hewlett Packard HP Workstation D3H66UT User Manual
Garmin Gladiator TR 1 User Manual
FIC EMB 800 Series User Manual
Electrolux Thermaline 9CHG584145 User Manual
Computer Tech Link 910TF User Manual
ClearOne comm Chat 50 User Manual
Belkin F9L1109V1 User Manual
ATTO Technology Computer Hardware FC 41ES User Manual
AT T 5927B User Manual
Asus E3001 User Manual