Dell P170S/P190S Flat Panel Monitor User's Guide
Dell™ P170S/P190S Flat Panel Monitor User's Guide
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not
followed.
WARNING: A Warning indicates a potential for property damage, personal injury or death.
Information in this document is subject to change without notice.
© 2010 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries; ENERGY STAR is a registered trademark of the U.S. Environmental
Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model P170Sb/P190Sb/P170St/P190St/P170Sf/P190Sf/P190Sc
January 2010 Rev. A02
file:///S|/SSA_Proposal/P170S_P190S/UG/index.htm[7/8/2011 4:47:10 PM]
Dell P170S/P190S Flat Panel Monitor
Setting Up Your Monitor
Dell™ P170S/P190S Flat Panel Monitor
If you have a non Dell™ desktop, portable computer, or graphics
card
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Select Advanced.
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).
5. Please refer to the graphics card provider website for updated driver (for example, http://www.ATI.com OR
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1280x1024 again.
NOTE: If you are unable to set the resolution to 1280x1024 , please contact the manufacturer of your computer or
consider purchasing a graphics adapter that will support the video resolution of 1280x1024 .
file:///S|/SSA_Proposal/P170S_P190S/UG/non-dell.htm[7/8/2011 4:48:12 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
Operating the Monitor
Dell™ P170S/P190S Flat Panel Monitor User's Guide
Using the Front Panel Controls
Use the control buttons on the front of the monitor to adjust the characteristics of the image being displayed. As you use these buttons to adjust the controls, an OSD shows the numeric values of
the characteristics as they change.
Front panel Button
Description
Use the Input Select button to select between two different video signals that may be connected to your monitor.
If both VGA and DVI cables are connected to one PC, this monitor will display an image automatically just as long as a video signal is present in either
VGA or DVI outputs. When connecting one display to two PCs, if using screen savers, best to set both to the exact times. Whichever mouse is moved
first will activate that video input first.
NOTE:The floating 'Dell Self-test Feature Check' dialog appears on a black background if the monitor cannot sense
a video signal. Using the input select button, select the desired input to be tested either Analog Input or Digital
Input. Disconnect the video cable from the video card and the Dell Self-test Feature Check dialogue box will appear
if the display is operating correctly.
Input select
or
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
or
The Menu button is used to open and exit the on-screen display (OSD), and exit from menus and sub-menus. See Using the OSD Menu.
OSD menu / select
Use these buttons to adjust (decrease/increase ranges) items in the OSD menu.
Down (-) and Up (+)
Brightness/Contrast
Auto Adjust
Use this button to launch Brightness/Contrast Menu.
Use this button to activate automatic setup and adjustment. The following dialog appears on a black screen as the monitor self-adjusts to the current
input:
Auto Adjustment button allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your monitor
by using the Pixel Clock (Coarse), Phase (Fine) controls in the OSD.
NOTE: Auto Adjust does not occur if you press the button while there are no active video input signals or attached cables.
Use the power button to turn the monitor on and off.
The green light indicates the monitor is on and fully functional. An amber light indicates power save mode.
Power Button and
Indicator
Using the On-Screen Display (OSD) Menu
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
Accessing the Menu System
NOTE:If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor automatically saves those changes. The changes are also
saved if you change the settings and then wait for the OSD menu to disappear.
Push the MENU button to open the OSD menu and display the main menu.
1. Push the MENU button to launch the OSD menu and display the main menu.
Main Menu for Auto Detect Analog (VGA)
Input
Main Menu for Auto Detect Digital (DVI)
Input
or
Main Menu for Analog (VGA) Input
Main Menu for Digital (DVI) Input
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
or
NOTE: Auto Adjust, Positioning and Image Settings are only available when you are using the analog (VGA) connector.
2. Push the - and + buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table below for a complete list of all the options
available for the monitor.
3. Push the MENU button once to activate the highlighted option.
4. Push - and + button to select the desired parameter.
5. Push MENU to enter the slide bar and then use the - and + buttons, according to the indicators on the menu, to make your changes.
6. Push the MENU button once to return to the main menu to select another option or push the MENU button two or three times to exit from the OSD menu.
Icon
Menu and
Submenus
Description
Exit
Select to exit the Main menu.
Brightness/
Contrast
Brightness adjusts the luminance of the backlight.
Adjust Brightness first, then adjust Contrast only if further adjustment is necessary.
Push the + button to increase luminance and push the - button to decrease luminance (min 0 ~ max 100).
Contrast adjusts the degree of difference between darkness and lightness on the monitor screen.
Push the + button to increase the contrast and push the - button to decrease the contrast (min 0 ~ max 100).
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
Positioning:
Horizontal
Vertical
Positioning moves the viewing area around on the monitor screen.
When making changes to either the Horizontal or Vertical settings, no changes occur to the size of the viewing area. The image shifts in response to your selection.
Minimum is 0 (-) and maximum is 100 (+).
NOTE:When using DVI source, the Positioning option is not available.
Auto Adjust
Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with your particular setup.
Select to activate automatic setup and adjustment. The following dialog appears on a black screen as the monitor self-adjusts to the current input:
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your monitor by using the Pixel
Clock (Coarse) and Phase (Fine) controls under Image Settings.
NOTE:In most cases, Auto Adjust produces the best image for your configuration.
Image settings: The Phase and Pixel Clock adjustments allow you to more closely adjust your monitor to your preference. These settings are accessed through the main OSD menu,
by selecting Image Settings.
Pixel Clock
Phase
Use the - and + buttons to make adjustments. (Minimum: 0 ~ Maximum: 100)
If satisfactory results are not obtained using the Phase adjustment, use Pixel Clock (Coarse) and then use Phase (fine), again.
NOTE: This function may change the width of the display image. Use the Horizontal function of the Position menu to center the display image on the screen.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
NOTE:When using DVI source, the Image Settings option is not available.
Color Settings
Color Settings adjusts the color temperature, color hue, and saturation.
The color hue is most noticeable in areas of white.
Normal Preset
Blue Preset
Normal Preset is selected to obtain the default (factory) color settings. This setting is also the “sRGB” standard default color space.
Blue Preset is selected to obtain a bluish tint. This color setting is typically used for text based applications (spreadsheets, programming, text editors, etc.).
Red Preset
User Preset
Red Preset is selected to obtain a redder tint. This color setting is typically used for color-intensive applications (photograph image editing, multimedia,
movies, etc.).
User Preset: Use the plus and minus buttons to increase or decrease each of the three colors (R, G, B) independently, in single digit increments, from 0 to
100.
Adjust the settings for the OSD, including the location, the amount of time the menu remains on-screen, and the rotation of the OSD.
OSD Settings:
Horizontal
Position
Position of the OSD:
To adjust the horizontal position of the OSD, use the - and + buttons, and move OSD to the left and right.
Vertical
Position
To adjust the vertical position of the OSD, use the - and + buttons, and move OSD down and up.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
OSD Hold Time
OSD Hold Time:
The OSD stays active for as long as it is in use. Adjusting the hold time, sets the length of time the OSD remains active after the last time you pressed a button.
Use the - and + buttons to adjust the slider in 5 second increments, from 5 to 60 seconds.
OSD Rotation:
OSD Rotation
OSD Lock
OSD Lock:
Controls user access to adjustments. When Yes (+) is selected, no user adjustments are allowed. All buttons are locked except the menu button.
NOTE: When the OSD is locked, pressing the menu button takes the user directly to the OSD settings menu, with OSD Lock selected. Select No (-) to unlock
and allow user access to all applicable settings.
NOTE: You can also lock or unlock the OSD by pushing and holding the Menu button for
15 seconds.
Language
Select to have the OSD display in one of 8 languages (English, French, Spanish, German, Japanese, Brazilian Portuguese, Russian and Simplified Chinese).
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
NOTE: The change only affects the OSD. It has no effect on any software running on the computer.
Audio
You can select to have the audio on or off when the monitor is in power saving mode.
(optional)
Yes — enables audio
No — disables audio (default)
NOTE: When the Dell Soundbar is not properly connected to the monitor, the audio menu
is not available.
Factory Reset:
Reset the OSD menu options to the factory preset values.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
Exit — Select to exit out of Reset to Factory Settings menu without resetting any OSD options.
Position settings only — Change the settings for Image Position back to original factory settings.
Color settings only — Change the Red, Green, and Blue settings back to their original factory settings and set the default setting for Normal Preset.
All settings — Change all the user-adjustable settings including color, position, brightness, contrast and OSD hold time to the factory defaults. The language of
the OSD does not change.
IR — This feature will help reduce minor cases of image retention.
Enable LCD Conditioning: If an image appears to be stuck on the monitor, select LCD Conditioning to help eliminate any image retention. Using the LCD
Conditioning feature may take several hours. Severe cases of image retention are known as burn-in, the LCD Conditioning feature does not remove burn-in.
NOTE: Use LCD Conditioning only when you experience a problem with image retention.
Below warning message appears once user select “Enable LCD Conditioning”:
NOTE: Press any button on the monitor to terminate LCD Conditioning at any time.
DDC/CI — Enable the DDC/CI control function.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
DDC/CI (Display Data Channel/Command Interface) allows you to adjust the monitor parameters (brightness, color balance, etc) via software applications on your
PC.
Default is "Enable". You can disable this feature by selecting "Disable".
For best user experience and optimum performance of your monitor, keep this feature enabled.
NOTE:If user select "Disable", display Warning message box as below. Select "Yes" disable DDC/CI and
return to "Factory Reset" menu. Warning message time-out in 20 sec.
OSD Warning Messages
The following warning messages may appear on the screen indicating that the monitor is out of synchronization.
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the Horizontal and Vertical frequency ranges
addressable by this monitor. Recommended mode is 1280 X 1024.
NOTE: The floating Dell Self-test Feature Check dialog appears on-screen if the monitor cannot sense a video signal.
or
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
or
Occasionally, no warning message appears, but the screen is blank. This could also indicate that the monitor is not synchronizing with the computer.
See Solving Problems
Setting the Maximum Resolution
To set the maximum resolution for the monitor:
1. Right-click on the desktop and select Properties.
2. Select the Settings tab.
3. Set the screen resolution to 1280 X 1024.
4. Click OK.
If you do not see 1280 X 1024 as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following procedures:
If you have a Dell desktop or portable computer:
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
If you are using a non-Dell computer (portable or desktop):
Go to the support site for your computer and download the latest graphic drivers.
Go to your graphics card website and download the latest graphic drivers.
Using the Dell Soundbar (Optional)
The Dell Soundbar is a stereo two channel system adaptable to mount on Dell flat panel displays. The Soundbar has a rotary volume and on/off control to adjust the overall system level, a blue LED
for power indication, and two audio headset jacks.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
1. Power/volume control
2. Power indicator
3. Headphone connectors
Using the Tilt, Swivel, and Vertical Extension
NOTE: This is applicable for a monitor with a stand. When the OptiPlex™ USFF 780/OptiPlex™ SFF 980 AIO Stand is bought, please refer to the respective AIO stand setup guide for set up
instructions.
Tilt/Swivel
With the built-in stand, you can tilt and/or swivel the monitor for the most comfortable viewing angle.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
NOTE:Stand is detached and extended when the monitor is shipped from the factory.
Vertical Extension
Stand extends vertically up to 130mm.
Changing the Rotation of Your Monitor
Before you rotate the monitor, your monitor should either be vertically extended (Vertical Extension) or titled (Tilt) to avoid hitting the bottom edge of the monitor.
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Operating the Monitor:Dell P170S/P190S Flat Panel Monitor User's Guide
file:///S|/SSA_Proposal/P170S_P190S/UG/operate.htm[7/8/2011 4:48:31 PM]
Dell P170S/P190S Flat Panel Monitor
Setting Up Your Monitor
Dell™ P170S/P190S Flat Panel Monitor
Important instructions to set the display resolution to
1280x1024 (Maximum Resolution)
For optimal display performance while using the Microsoft Windows® operating systems, set the display resolution to
1280x1024 pixels by performing the following steps:
1. Right-click on the desktop and click Properties.
2. Select the Settings tab.
3. Move the slider-bar to the right by pressing and holding the left-mouse button and adjust the screen resolution to
1280x1024.
4. Click OK.
If you do not see 1280x1024 as an option, you may need to update your graphics driver. Please choose the scenario
below that best describes the computer system you are using, and follow the provided directions:
file:///S|/SSA_Proposal/P170S_P190S/UG/optimal.htm[7/8/2011 4:48:49 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Setting Up the Monitor
Dell™ P170S/P190S Flat Panel Monitor User's Guide
Attaching the Stand
NOTE: Stand is detached when the monitor is shipped from the factory.
NOTE: This is applicable for a monitor with a stand. When the OptiPlex™ USFF 780/OptiPlex™ SFF 980 AIO Stand is bought, please refer to the respective
AIO stand setup guide for set up instructions.
Remove the monitor cover and place the monitor on it.
1. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor.
2. Lower the stand so that the monitor mounting area snaps onto the stand.
Connecting the Monitor
To connect your monitor to the computer perform the following steps/instructions:
1. Turn off your computer and disconnect the power cable.
2. Connect either the white (digital DVI-D) or the blue (analog VGA) display connector cable to the corresponding video port on the back of your computer. Do not connect both
file:///S|/SSA_Proposal/P170S_P190S/UG/setup.htm[7/8/2011 4:49:17 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
cables on the same computer. Use both the cables only when they are connected to two different computers with appropriate video systems.
Connecting the Blue VGA Cable
Connecting the White DVI Cable
NOTE: The Graphics are used for the purpose of illustration only. Appearance of the the computer may vary.
After you have completed connecting the VGA/DVI cable, follow the procedure below to complete your monitor setup:
file:///S|/SSA_Proposal/P170S_P190S/UG/setup.htm[7/8/2011 4:49:17 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
1. Plug the power cables for your computer and monitor into a nearby outlet.
2. Turn on the monitor and the computer.
If your monitor displays an image, installation is complete. If it does not display an image, see Solving Problems.
Organizing Your Cables
After attaching all necessary cables to your monitor and computer (see Connecting Your Monitor), use the cable management slot to organize all cables as shown above.
Attaching the Soundbar (Optional)
file:///S|/SSA_Proposal/P170S_P190S/UG/setup.htm[7/8/2011 4:49:17 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
1. Working from the rear of the monitor, attach the Soundbar by aligning the two slots with the two tabs along the bottom rear of the monitor.
2. Slide the Soundbar to the left until it snaps into place.
3. Connect the Soundbar with the DC power connector.
4. Insert the mini stereo plug from the rear of the Soundbar into the computer's audio output jack.
CAUTION: Do not use with any device other than the Dell Soundbar
Removing the Stand
After placing the monitor panel on a soft cloth or cushion, press and hold the stand removal button, and then remove the stand.
file:///S|/SSA_Proposal/P170S_P190S/UG/setup.htm[7/8/2011 4:49:17 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a clean surface.
NOTE: This is applicable for a monitor with a stand. When the OptiPlex™ USFF 780/Optiplex™ SFF 980 AIO Stand is bought, please refer to the respective AIO
stand setup guide for set up instructions.
file:///S|/SSA_Proposal/P170S_P190S/UG/setup.htm[7/8/2011 4:49:17 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Solving Problems
Dell™ P170S/P190S Flat Panel Monitor User's Guide
Self-Test
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly connected but the
monitor screen remains dark, run the monitor self-test by performing the following steps:
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer. To ensure proper Self-Test operation, remove the Analog (blue connector) cables from the back of computer.
3. Turn on the monitor.
The floating 'Dell™ - Self Test Feature Check' dialog box should appear on-screen (against a black background) if the monitor cannot sense a video signal and is working
correctly. While in self-test mode, the power LED remains green. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll through
the screen.
or
or
4. This box also appears during normal system operation if the video cable becomes disconnected or damaged.
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Built-in Diagnostics
Your monitor has a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or with your
computer and video card.
NOTE: You can run the built-in diagnostics only when the video cable is unplugged and the monitor is in self-test mode.
To run the built-in diagnostics:
1. Ensure that the screen is clean (no dust particles on the surface of the screen).
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self-test mode.
3. On the front panel, press and hold the Menu (button 2) and + (button 4) keys on the front panel, simultaneously for 2 seconds. A gray screen appears.
file:///S|/SSA_Proposal/P170S_P190S/UG/solve.htm[7/8/2011 4:49:32 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
4. Carefully inspect the screen for abnormalities.
5. Press the + (button 4) key on the front panel again. The color of the screen changes to red.
6. Inspect the display for any abnormalities.
7. Repeat steps 5 and 6 to inspect the display in green, blue, and white colored screens.
The test is complete when the white screen appears. To exit, press the + (button 4) again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
OSD Warning Messages
Common Problems
The following table contains general information about common monitor problems that you might encounter and the possible solutions.
Common Symptoms
What You Experience
No picture
Possible Solutions
No Video/Power LED off
Ensure that the video cable connecting the monitor and the computer is properly connected and
secure.
Verify that the power outlet is functioning properly using any other electrical equipment.
Ensure that the power button is depressed fully.
No Video/Power LED on
No picture or no brightness
Increase brightness & contrast controls via OSD.
Perform monitor Self Test Feature Check.
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
Poor Focus
Picture is fuzzy, blurry, or ghosting
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Eliminate video extension cables.
Reset the monitor to Factory Settings.
Shaky/Jittery Video
Wavy picture or fine movement
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Reset the monitor to Factory Settings.
Check environmental factors.
Relocate the monitor and test in another room.
Missing Pixels
LCD screen has spots
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
Run the built-in diagnostics.
Stuck-on Pixels
Brightness Problems
LCD screen has bright spots
Picture too dim or too bright
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
Run the built-in diagnostics.
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
Geometric Distortion
Screen not centered correctly
Screen has one or more lines
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
Horizontal/Vertical Lines
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor Self Test Feature Check and determine if these lines are also in self-test mode.
Check for bent or broken pins in the video cable connector.
file:///S|/SSA_Proposal/P170S_P190S/UG/solve.htm[7/8/2011 4:49:32 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Synchronization Problems
Screen is scrambled or appears torn
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor Self Test Feature Check to determine if scrambled screen appears in self-test mode.
Check for bent or broken pins in the video cable connector.
Restart the computer in the safe mode.
Safety Related Issues
Intermittent Problems
Visible signs of smoke or sparks
Monitor turns on & off
Do not perform any troubleshooting steps.
Contact Dell immediately.
Ensure that the video cable connecting the monitor to the computer is connected properly and is
secure.
Reset the monitor to Factory Settings.
Perform monitor Self Test Feature Check to determine if the intermittent problem occurs in self-test
mode.
Missing Color
Wrong Color
Picture lacks color
Perform monitor Self Test Feature Check.
Ensure that the video cable connecting the monitor to the computer is connected properly and is
secure.
Check for bent or broken pins in the video cable connector.
Picture color is not good
Change the color to "User Preset"
Adjust R/G/B value of "User Preset"
Image retention from a static
image left on the monitor for a
long period of time
Faint shadow from the static image
displayed appears on the screen
Use the Power Management feature to turn off the monitor at all times when not in use (for more
Alternatively, use a dynamically changing screensaver.
Product-Specific Problems
SPECIFIC SYMPTOMS
WHAT YOU EXPERIENCE
POSSIBLE SOLUTIONS
Screen image is too small
Image is centered on screen, but
does not fill entire viewing area
Perform monitor reset on "Factory Reset"
Cannot adjust the monitor with
the buttons on the front panel
OSD does not appear on the
screen
Turn the monitor off and unplug the power cord and then plug back and power on
No Input Signal when user
controls pressed
No picture, the LED light is green.
When press "+", "-" or "Menu"
key, the message " No input
signal " will appear.
Check the signal source. Ensure that the computer is not in power saving by moving the mouse or
pressing any key on the keyboard.
Check whether the signal cable is plugged in and seated properly. Re-plug the signal cable if
necessary.
Re-boot the computer or video player.
The monitor will not fill the entire The picture does not fill the height
Due to the non-standard formats of DVDs, the monitor may not show the full screen pictures.
screen.
or width of the screen.
USB Problems
Specific Symptoms
USB interface is not working
What You Experience
USB peripherals are not working.
Possible Solutions
Check that your monitor is turned ON.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream connector).
Switch off and then turn on the monitor again.
High Speed USB 2.0 interface is High Speed USB 2.0 peripherals working slowly or not
slow at all.
Check that your computer is USB 2.0 capable.
Verify USB 2.0 source on your computer.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream connector).
Troubleshooting the Dell™ Soundbar (Optional)
COMMON SYMPTOMS
No Sound
WHAT YOU EXPERIENCE
POSSIBLE SOLUTIONS
Soundbar has power - power
indicator is on.
Plug the audio line-in cable into the computer's audio out jack.
Set all Windows volume controls to their maximum.
Play some audio content on the computer (i.e., audio CD, or MP3).
Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
Clean and reseat the audio line-in plug.
file:///S|/SSA_Proposal/P170S_P190S/UG/solve.htm[7/8/2011 4:49:32 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Test the Soundbar using another audio source (i.e., portable CD player).
Distorted Sound
Computer's sound card is used as
the audio source.
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card.
Set all Windows volume controls to their midpoints.
Decrease the volume of the audio application.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (i.e., portable CD player).
Distorted Sound
Other audio source is used.
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the audio source.
Decrease the volume of the audio source.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
Clean and reseat the audio line-in plug.
Unbalanced Sound Output
Sound from only one side of
Soundbar
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card or audio
source.
Set all Windows audio balance controls (L-R) to their midpoints.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (i.e., portable CD player).
Low Volume
Volume is too low
Clear any obstructions between the Soundbar and the user.
Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume setting.
Set all Windows volume controls to their maximum.
Increase the volume of the audio application.
Test the Soundbar using another audio source (i.e., portable CD player).
file:///S|/SSA_Proposal/P170S_P190S/UG/solve.htm[7/8/2011 4:49:32 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
About Your Monitor
Dell™ P170S/P190S Flat Panel Monitor User's Guide
Package Contents
Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.
NOTE: Some items may be optional and may not ship with your Monitor. Some features or media may not be available in certain countries.
NOTE: Stand and cables are not included, when purchased with OptiPlex™ USFF 780/OptiPlex™ SFF 980 AIO Stands.
NOTE: To set up with the respective AIO stand, please refer to the respective stand setup guide for setup instructions.
Monitor with stand
Power Cable
VGA Cable
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
DVI Cable
USB upstream cable
Drivers and Documentation media
Quick Setup Guide
Safety Information
Product Features
The P170S/P190S flat panel display has an active matrix, thin-film transistor (TFT), and liquid crystal display (LCD). The monitor features include:
■ P170S: 17-inch (432 mm) viewable area display (measured diagonally). 1280 x 1024 resolution, plus full-screen support for lower resolutions.
■ P190S: 19-inch (481.9 mm) viewable area display (measured diagonally). 1280 x 1024 resolution, plus full-screen support for lower resolutions.
■ Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side to side.
■ Tilt, swivel, vertical extension and rotate adjustment capabilities.
®
■ Removable stand and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions.
■ Plug and play capability if supported by your system.
■ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
■ Software and documentation CD which includes an information file (INF), Image Color Matching File (ICM), and product documentation.
■ Energy Saver feature for Energy Star compliance.
■ Security lock slot.
■ EPEAT Gold Rating.
■ Halogen Reduced.
■ Asset Management.
Identifying Parts and Features
Front View
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Front View
Front panel controls
Label
Description
1
2
3
4
5
Video input select
OSD menu / select button
Brightness & Contrast / Down (-) button
Auto-Adjust / Up (+) button
Power button (with power light indicator)
Back View
Back view
Label
VESA mounting holes (100mm)
Description/Use
1
Use to mount the monitor.
(behind attached VESA Plate)
2
3
4
5
6
7
Barcode serial number label
Security lock slot
Refer to this label if you need to contact Dell for technical support.
Use a security lock with the slot to help secure your monitor.
Attach the optional Dell Soundbar.
Dell Soundbar mounting brackets
Regulatory rating label
Stand removal button
Lists the regulatory approvals.
Press to release the stand.
Cable management slot
Help organize cables by placing them through the slot.
Side View
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
USB
connectors
(downstream)
Right side
Left side
Bottom View
Bottom view
Label
Description
1
2
3
4
Power connector
Insert the power cable.
Dell Soundbar power connector
DVI connector
Connect the power cord for the Soundbar (optional).
Connect your computer DVI cable.
VGA connector
Connect your computer VGA cable.
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Connect the USB cable that came with your monitor to the monitor and the computer. Once this
cable is connected you can use the USB connectors on the side and bottom of the monitor.
5
6
USB upstream connector
USB connector
Connect your USB devices.
Monitor Specifications
Power Management Modes
If you have VESA's DPMS™ compliance display card or software installed in your computer, the monitor can automatically reduce its power consumption when not in use. This is
referred to as Power Save Mode. If input from a keyboard, mouse or other input devices is detected by the computer, the monitor will automatically "wake up". The following table
shows the power consumption and signaling of this automatic power-saving feature:
P170S
VESA Modes
Horizontal
Sync
Vertical Sync
Video
Power
Indicator
Power Consumption
Normal operation
Active
Active
Active
Green
50 W (maximum)
22 W (typical)
Less than 1 W
Less than 1 W
Active-off mode
Switch off
Inactive
-
Inactive
-
Blanked
-
Amber
Off
P190S
VESA Modes
Horizontal
Sync
Vertical Sync
Video
Power
Indicator
Power Consumption
Normal operation
Active
Active
Active
Green
53 W (maximum)
25 W (typical)
Less than 1 W
Less than 1 W
Active-off mode
Switch off
Inactive
-
Inactive
-
Blanked
-
Amber
Off
NOTE: This monitor is ENERGY STAR®-compliant as well as TCO '03 power management
compatible.
NOTE: Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the
monitor.
Pin Assignments
VGA Connector
Pin Number
15-pin Side of the Connected Signal
Cable
1
2
3
4
5
6
7
8
Video-Red
Video-Green
Video-Blue
GND
Self-test
GND-R
GND-G
GND-B
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
9
Computer 5V/3.3V
GND-sync
GND
10
11
12
13
14
15
DDC data
H-sync
V-sync
DDC clock
DVI Connector
Pin
24-pin Side of the Connected Signal
Number Cable
1
2
3
4
5
TMDS RX2-
TMDS RX2+
TMDS Ground
Floating
Floating
6
DDC Clock
DDC Data
7
8
Floating
9
TMDS RX1-
TMDS RX1+
TMDS Ground
Floating
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Floating
+5V/+3.3V power
Self test
Hot Plug Detect
TMDS RX0-
TMDS RX0+
TMDS Ground
Floating
Floating
TMDS Ground
TMDS Clock+
TMDS Clock-
Universal Serial Bus (USB) Interface
This monitor supports High-Speed Certified USB 2.0 interface.
Data Rate Power Consumption
High speed 480 Mbps
Full speed 12 Mbps
2.5W (Max., each port)
2.5W (Max., each port)
2.5W (Max., each port)
Low speed 1.5 Mbps
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
USB ports:
1 upstream - rear
4 downstream - 2 on rear; 2 on left side
NOTE: USB 2.0 capability requires 2.0-capable computer.
NOTE: The USB interface of the monitor works ONLY when monitor is powered ON (or in Power Save Mode). Switching your monitor OFF and then ON would re-enumerate its
USB interface; attached peripherals may take a few seconds to resume normal functionality.
Flat Panel Specifications
Model
P170S
P190S
Screen type
Panel type
Active matrix - TFT LCD
TN
Active matrix - TFT LCD
TN
Screen dimensions
17 inches (17-inch diagonal viewable image size) 19 inches (19-inch diagonal viewable image size)
Preset display area:
Horizontal
337.9 mm (13.3 inches)
270.3 mm (10.6 inches)
376.3 mm (14.8 inches)
301.1 mm (11.8 inches)
Vertical
Pixel pitch
0.264 mm
0.294 mm
Viewing angle
160° (vertical) typical, 170° (horizontal) typical
160° (vertical) typical, 170° (horizontal) typical
Luminance output
Contrast ratio
Faceplate coating
Backlight
250 CD/m² (typical)
800 to 1 (typical)
Antiglare with hard-coating 3H
2 CCFLs backlight
5 ms typical
250 CD/m² (typical)
800 to 1 (typical)
Antiglare with hard-coating 3H
2 CCFLs backlight
5 ms typical
Response Time
Color Depth
16.7 mil colors
16.7 mil colors
Color Gamut
72 %*
72 %*
* P170S/P190S Color Gamut (Typical) is based on CIE1976 (85%) and CIE1931 (72%).
Resolution
Model
P170S/P190S
Horizontal scan range
Vertical scan range
Maximum preset resolution
30 kHz to 81 kHz (automatic)
56 Hz to 76 Hz (automatic)
1280 x 1024 at 60 Hz
Preset Display Modes
P170S/P190S
Display Mode
Horizontal Frequency Vertical Frequency
Pixel Clock
(MHz)
Sync Polarity
(Horizontal/Vertical)
(kHz)
31.5
31.5
37.5
37.9
46.9
48.4
60.0
67.5
64.0
80.0
(Hz)
70.1
60.0
75.0
60.3
75.0
60.0
75.0
75.0
60.0
75.0
VGA, 720 x 400
28.3
25.2
31.5
40.0
49.5
65.0
78.8
108.0
108.0
135.0
-/+
-/-
VGA, 640 x 480
VESA, 640 x 480
VESA, 800 x 600
VESA, 800 x 600
VESA, 1024 x 768
VESA, 1024 x 768
VESA, 1152 x 864
VESA, 1280 x 1024
VESA, 1280 x 1024
-/-
+/+
+/+
-/-
+/+
+/+
+/+
+/+
Electrical
Model
P170S/P190S
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Analog RGB, 0.7 Volts +/- 5%, 75 ohm input impedance
Video input signals
Digital DVI-D TMDS, 600mV for each differential line, positive
polarity at 50 ohm input impedance
separate horizontal and vertical,
3.3V Cmos or 5V TTL level, positive or negative sync.
Synchronization input signals
AC input voltage/frequency/current
Inrush iso surge current
100 to 240 VAC / 50-60 Hz + 3 Hz / 1.5 A Max.
120 V: 30 A (Max.)
240 V: 60 A (Max.)
Physical Characteristics
Model
P170S
D-sub: blue connector
P190S
D-sub: blue connector
Connector type
DVI-D: white connector
DVI-D: white connector
D-sub: Detachable, Analog, 15
pin, shipped attached to the
monitor
D-sub: Detachable, Analog, 15 pin,
shipped attached to the monitor
Signal cable type
Digital: Detachable, DVI-D,
Solid pins, shipped detached
from the monitor
Digital: Detachable, DVI-D, Solid pins,
shipped detached from the monitor
Dimensions (with stand)
Height (Compressed)
332.16 mm (13.08 inches)
462.16 mm (18.20 inches)
372.10 mm (14.65 inches)
182.25 mm (7.18 inches)
362.6 mm (14.26 inches)
Height (Extended)
492.6 mm (19.39 inches)
410.1 mm(16.15 inches)
182.0 mm (7.17 inches)
Width
Depth
Dimensions (without stand)
Height
309.25 mm (12.18 inches)
372.10 mm (14.65 inches)
59.20 mm (2.33 inches)
338.1 mm (13.31 inches)
410.1 mm (16.15 inches)
65.9 mm (2.59 inches)
Width
Depth
Stand dimensions
Height (Compressed)
Height (Extended)
Width
331.70 mm (13.06 inches)
381.57 mm (15.02 inches)
337.20 mm (13.28 inches)
182.30 mm (7.18 inches)
347.7 mm (13.69 inches)
396.7 mm (15.62 inches)
337.6 mm (13.29 inches)
182.0 mm (7.17 inches)
Depth
Weight
Weight with packaging
Weight with stand assembly and cables
6.50 kg (14.30 lb)
5.10 kg (11.22 lb)
7.6 kg (16.70 lb)
6.4 kg (14.08 lb)
Weight without stand assembly
(for wall mount or VESA mount considerations - no cables)
3.65 kg (8.03 lb)
1.55 kg (3.42 lb)
4.3 kg (9.46 lb)
1.6 kg (3.52 lb)
Weight of stand assembly
Environmental
Model
P170S
P190S
Temperature
Operating
0° to 40° C (32° to 104°F)
0° to 40° C (30° to 104°F)
Storage: -20° to 60° C (-4° to 140° F)
Shipping: -20° to 60° C (-4° to 140° F)
Storage: -20° to 60° C (-4° to 140° F)
Shipping: -20° to 60° C (-4° to 140° F)
Non-operating
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Humidity
Operating
10% to 80% (non-condensing)
10% to 80% (non-condensing)
Storage: 5% to 90% (non-condensing)
Shipping: 5% to 90% (non-condensing)
Storage: 5% to 90% (non-condensing)
Shipping: 5% to 90% (non-condensing)
Non-operating
Altitude
Operating
3,048 m (12,000 ft) max
9,144 m (40,000 ft) max
3,048 m (12,000 ft) max
9,144 m (40,000 ft) max
Non-operating
171.00 BTU/hour (maximum)
75.24 BTU/hour (typical)
181.26 BTU/hour (maximum)
85.50 BTU/hour (typical)
Thermal dissipation
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID)
using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the monitor settings. If required, the user can select different settings, but in most
cases monitor installation is automatic.
LCD Monitor Quality & Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and do not affect the
display quality or usability. For more information, see Dell Support site at: support.dell.com.
Maintenance Guidelines
Caring for Your Monitor
monitor.
WARNING: Before cleaning the monitor, unplug the monitor from the
electrical outlet.
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:
To clean your antistatic screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic coating. Do
not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the monitor.
If you notice a white powder when you unpack your monitor, wipe it off with a cloth.
Handle your monitor with care as dark-colored monitors may scratch and show white scuff marks more than lighter-colored monitors.
To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.
file:///S|/SSA_Proposal/P170S_P190S/UG/about.htm[7/8/2011 4:49:51 PM]
Dell P170S/P190S Flat Panel Monitor User's Guide
Appendix
Dell™ P170S/P190S Flat Panel Monitor User's Guide
CAUTION: Safety Instructions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation
may result in exposure to shock, electrical hazards, and/or mechanical hazards.
For information on safety instructions, see the Safety Information that ships with your monitor.
FCC Notice (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice,
packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and
product, and some services may not be available in your area. To contact Dell for sales, technical support, or
customer service issues:
1. Visit support.dell.com.
2. Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link based on your need.
5. Choose the method of contacting Dell that is convenient for you.
file:///S|/SSA_Proposal/P170S_P190S/UG/appendx.htm[7/8/2011 4:50:04 PM]
|
HP Hewlett Packard f1503 User Manual
Hitachi Travelstar HTS725050A9A361 User Manual
Hanns G Computer Monitor HSG1082 User Manual
GE 169068 User Manual
Electrolux EHP 601 K User Manual
CDA HCG501L User Manual
Blue Sea Systems BLUE SEAL EVOLUTION G518B CB User Manual
Belkin F9L1109V1 User Manual
AT T SB67108 User Manual
Asus Motherboard H61MA User Manual