Installation Instructions
Warming Drawer
Models:
DWD30, ERWDEWD24, EWD27,
EWD30, EWD27, IWD30, MRWD27,
MRWD30DH30, MWDV27,
MWDVDV30
Part No. 102345 Rev. S
Table of Contents
Before You Begin... ........................................................... 1 Installation Instructions.................................................... 7
Important Safety Instructions .......................................... 1
General Safety Precautions............................................. 2
Installation Specifications................................................ 3
Verifying the Package Contents....................................... 3
Installation Planning......................................................... 3
Install Support Platform in Cabinet .................................. 6
Electrical and Environmental Specifications .................... 6
Remove the Drawer ........................................................ 7
Installing the Chassis....................................................... 7
Re-installing the Drawer................................................... 8
Towel Rack Installation ................................................... 8
Verify Warming Drawer Operation ................................... 9
Installation Checklist ........................................................ 9
Before You Begin...
Important:
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully
before you begin the installation process. Leave these installation instructions with the customer.
Customer: Keep these installation instructions for future reference and the locrical inspector’s use.
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the
Dacor Distinctive Service line. Whenever you call, have
the complete model and serial number for your appliance
available. The numbers are found on the product data label
located on back of the drawer front.
The data label also contains the product electrical
requirements.
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada
Monday — Friday 6:00 a.m. to 5:00 p.m. Pa
Web site:
Product data label
on back for drawer
front
Dacor Distinctive Service (repaily)
Phone: (877) 337-3226 (U.S.A
Monday — Friday 6:00 a.m. e
Imant Safety Instructions
Safety Symbols and Labels
Important Information About
Safety Instructions
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or
operating this or any other appliance.
WARNING
Hazards or unsafe practices that COULD result in severe
personal injury or death.
•
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t
understand.
CAUtION
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
1
Important Safety Instructions
General Safety Precautions
To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including
the following:
WARNING
WARNING
• Clean the warming drawer thoroughly before
• Use this appliance only for its intended use as
described in this manual. Use it only to warm food
and heat plates and utensils. It is not designed for
commercial, industrial or laboratory use.
operating it for the first time.
• To reduce the risk of fire in the warming drawer, do
not overcook food. Do not leave it unattended with
paper, plastic or other combustible materials inside.
• Only model OWD24 is approved for use in outdoor
installations and near water (bathrooms). Do not
use, store or install warming drawer models other
than OWD24 near water, for example, near sinks,
swimming pools or in a wet basement.
• If materials inside the warming drawer should ignite,
keep the drawer closed and shut off the power at the
circuit breaker panel or fuse box.
• Exercise cautioopening the warming drawer.
Let hot air ope before looking or reaching
into the w
• Model OWD24, when installed as a towel warmer,
must be installed indoors and have the supplied wire
rack installed in the drawer bottom according to these
instructions.
• Use oen removing food and
coong drawer. Wet pot holders
cs.
• Do not install or operate a product that is
damaged, has a damaged power cord or plug, or is
malfunctioning in any manner. Return the appliance to
the nearest authorized service facility for examination,
repair or adjustment.
e whole eggs, sealed containers
ars in the drawer. They may explode
causing injury.
warming drawer is on in continuous mode
ill remain on until turned off manually. Exercise
ion when operating the unit in continuous mode.
• Make sure that the appliance has been properly
installed and grounded by a qualified installer
according to the accompanying installation
instructions. Have the installer show you
of the electrical outlet so that you know
disconnect power to the appliance.
Do not place more than 50 pounds in the drawer.
• Properly clean and maintain the unit regularly as
instructed in the use and care manual. Clean only
those parts listed, in the manner specified.
• Do not repair or replace any par
drawer unless specifically rec
literature accompanying it. ld be
done by a qualified techni
• Do not use abrasive scrubbers or abrasive/caustic
cleaners or detergents on this appliance. They may
permanently damage the finishes. Do not use aerosol
cleaners, because they may be flammable or cause
corrosion of metal parts.
• Use of accessory attachmentended by
the appliance manufacturer may injuries.
• Before cleaning or performing any type of service,
make sure that the power plug is disconnected from
the electrical outlet and that the unit is cool.
• Make sure the warming drawer is used only by those
individuals who are able to operate it properly.
• Do not tamper with the controls.
• DO NOT TOUCH ANY HOT SURFACES IN OR
ON THE WARMING DRAWER DURING OR
IMMEDIATELY AFTER USE. Use the handle instead.
After use, make sure these surfaces have had
sufficient time to cool before touching them. Heating
elements may be hot, even though they are dark in
color.
• Never allow anyone, including children to sit, stand
or climb on any part of the appliance, including the
drawer. Doing so may cause tipping, damage, serious
injury or death.
• Do not leave children unattended in the area around
the appliance. Do not allow children to operate it, play
with the controls, pull on the handle or touch other
parts. Do not store items of interest to children above
the warming drawer. Children could be burned or
injured while climbing on the appliance.
• To avoid the possibility of fire or burns, do not allow
clothing, potholders, towels or rags to come into
contact with any part of the warming drawer during
and immediately after use. Do not wear loose or
hanging apparel while using the appliance.
2
Installation Specifications
Verifying the Package Contents
C
B
•
(3) mounting screws - PN 83569
•
Wire rack with mounting hardware (OWD24 only)
(1) PN 83619 (screw), (1) PN 83267 (clamp)
Installation Planning
Chassis
E
•
A qualified technician must complete the installation of this built-
in appliance. Proper installation is the customer's responsibility.
•
Carefully check the location where the drawer is to be installed.
The drawer should be placed for convenient access. Make
certain that electrical power can be provided in the selected
location. Install the warming drawer in wood cabinets only.
5/16”
(8 mm)
•
Plan the installation so that all minimum clearances are met or
exceeded. Dimensions shown provide minimum clearances,
unless otherwise noted. Be certain that proper clearance is
provided for the drawer when it is in the open position.
r open
F
•
•
The specified minimum cabinet depth and width must be
provided. The cabinet depth and width must completely enclose
the recessed portion of the drawer.
Cabinet cutout dimensions must be used as indicated. All
contact surfaces between the appliance and the cabin
be solid and level. The drawer support platform mus
with the bottom edge of the cabinet cutout.
rall Dimensions - IWD/OWD Series
top View
•
•
•
Make certain that you have everything neces
proper installation before proceeding.
40" (101.6 cm)
3 prong
120 Vac power cord
Mounting hole,
9 places
A custom front panel is required for IW
series models and optional for OWD
An optional Epicure® style front p
is available for model OWD24
**
**
**
G
D
Chassis without
drawer installed
** = OWD24 mounting holes
A
Drawer Face Dimensions
Chassis Dimensions
(IWD/OWD Series)
(IWD/OWD Series)
(D)
(E)
(F)
(G)
(A) Dimension
Drawer Face
Width
(C) Dimension
Chassis Face
Width
(B) Dimension
Chassis Width
Dimension Dimension Dimension Dimension
Drawer
Face Height
Model
Chassis
Depth
Drawer
Depth
Chassis
Height
22 5/16” (56.7 cm) 22 1/4” (56.5 cm) 22 3/8” (56.8 cm)
25 5/16” (64.3 cm) 25 1/4” (64.1 cm) 25 3/8” (64.5 cm)
28 5/16” (71.9 cm) 28 1/4” (71.8 cm) 28 3/8” (72.1 cm)
IWD24
8 15/16”
(22.7 cm)
23 3/8”
(59.4 cm)
23 13/16”
(60.5 cm)
9 1/16”
(23.0 cm)
IWD27
IWD30
11 7/8”
(30.2 cm)
20”
(50.8 cm)
18”
(45.7 cm)
11 7/8”
(30.2 cm)
22 1/2” (57.1 cm) 22 1/2” (57.1 cm) 22 1/2” (57.1 cm)
OWD24
See following page for chassis dimensions for other models
3
Installation Specifications
(A) Drawer Face
Width
(B) Chassis Face
Model
(C) Chassis Width
Width
DWD30
30” (76.2 cm)
27” (68.6 cm)
30” (76.2 cm)
24” (61.0 cm)
27” (68.6 cm)
30” (76.2 cm)
36” (91.4 cm)
26 3/4” (67.9 cm)
29 3/4” (75.6 cm)
27” (68.6 cm)
30” (76.2 cm)
27” (68.6 cm)
30” (76.2 cm)
30” (76.2 cm)
29 5/8” (75.2 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
23 5/8” (60.0 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
35 5/8” (90.5 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
26 5/8” (67.6 cm)
29 5/8” (75.2 cm)
2(67.6 cm)
.2 cm)
m)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
22 1/4” (56.5 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
34 1/4” (87.0 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
25 1/4” (64.1 cm)
28 1/4” (71.8 cm)
28 1/4” (71.8 cm)
10 1/8”
(25.7 cm)
ERWD27
ERWD30
EWD24
EWD27
EWD30
EWD36
A
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
RWDV30
Drawer Face Dimensions
(MWD series shown)
B
C
Warmimensions
See page 3 fes chassis dimensions
ERWD
EWD
2”
9 cm)
3 7/16”
(8.7 cm)
23 3/8”
(59.4 cm)
Chassis
1 1/8”
(2.9 cm)
1”
(2.5 cm)
MWDH, MWDV,
RWDV
3 1/4”
MRWD30B
(only)
All other MRWD
series
1 7/16”
1”
(8.3 cm)
(3.7 cm)
(2.5 cm)
1”
(2.5 cm)
13/16”
(60.5 cm)
Drawer open
Handle Dimensions
40” (101.6 cm)
3-prong 120 Vac
power cord
Mounting
hole 9 places
9"
(22.9 cm)
Overall Dimensions
top View
1/2" (1.3 cm)
(EWD series shown)
10"
(25.4 cm)
Chassis without
drawer inserted
1/2" (1.3 cm)
Chassis Dimensions
4
Installation Specifications
27"/30"/36" Dacor
single wall oven
3/4" min.*
(1.9 cm)
Warming
drawer
D
C
D
C
C
C
36" typ.
(91.4 cm)
Warming
drawer
120 Vac
elect.
D
120 Vac
electrical
outlet
Warming
drawer
3/4" min.*
(1.9 cm)
Warming
drawer
120 Vac
elect.
A
B
1 1/2" (3.8 cm)
Typical countertop
Toe kick
Cooktop
3/4" min.*
(1.9 cm)
A
3/4” min.*
(1.9 cm)
Cutouts Dimensions
Warming
C
drawer
NOtES:
Models EWD36 and OWD24 cannot
installed above or below another
ing drawer (any type).
36" typ.
(91.4 cm)
120 Vac
electrical
outlet
A
B
OWD24 is not approved for
llation above, below or adjacent
a wall oven or a warming drawer,
including the same model.
(B) Min. Width to
(A) Cutout Width Adjacent Doors/
Drawers
D) Min. Vertical Gap
Between Cutouts
Min. Cutout
Depth
Model
DWD30
28 1/2” (72.4 cm) 30 1/4” (76.8 c
)
cm)
23.2 cm)
8” (23.2 cm)
1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
9 1/8” (23.2 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
ERWD27 25 1/2” (64.8 cm) 27 1/4” (69.
ERWD30 28 1/2” (72.4 cm) 30 1/4” (
EWD24
EWD27
EWD30
EWD36
IWD24
IWD27
IWD30
22 1/2” (57.2 cm) 24 1/
25 1/2” (64.8 cm) 2
28 1/2” (72.4 cm)
34 1/2” (87.6 c)*
22 1/2” (57.2
25 1/2” (64.8 cm)
28 1/2” (72.4 cm)
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/16” (2.7 cm)
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
1 1/4” (3.2 cm)*
NA
24” (61.0 cm)
**
MRWD27 25 1/2” (64.8 cm)
27” (68.6 cm)*
30” (76.2 cm)*
MRWD30 28 1/2” (72.4 cm)
MWDH27 25 1/2” (64.8 cm) 27 1/4” (69.2 cm)*
MWDH30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*
MWDV27 25 1/2” (64.8 cm) 27 1/4” (69.2 cm)*
MWDV30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*
OWD24
22 5/8” (57.5 cm) 24 1/4” (61.6 cm)*** 11 15/16” (30.3 cm)
9 1/8” (23.2 cm)
20 1/8” (51.1 cm)
24” (61.0 cm)
RWDV30 28 1/2” (72.4 cm) 30 1/4” (76.8 cm)*
1 1/4” (3.2 cm)*
* Bare minimum spacing to allow for ventilation and avoid scraping on DWD, ERW, EWD, MRW, MWD and RWD models.
** IWD models or OWD24 without the optional front panel kit: The chassis and drawer faceplate are smaller than the
cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must
exceed the cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom
and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and
below cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
5
Installation Specifications
Install Support Platform in
Cabinet
Chassis
face
Provide a platform (100 lb. load capacity) within the cabinet
upon which the warming drawer will be supported. The
platform must be installed level and straight. The top edge
of the platform must be flush with the cutout at the front of
the cabinet. There are no provisions to level the warming
drawer after it has been installed. 3/4” (1.9 cm) thick
plywood is recommended.
Support
platform
NOtE: If the drawer is not installed in a level fashion, the
drawer may slide open on its own or may not seal tightly,
allowing heat to escape and resulting in poor warming
drawer performance.
•
•
Minimum aming temperature: 32°F (0°C).
Electrical and Environmental
Specifications
The correcy and amperage must be
supplieet from a grounded, single
phated by a properly sized circuit
buse.
WARNING
•
e, frequency and amperage ratings
product data label. See page 1 for
IMPORtANt: This appliance is equipped with a three
prong grounding electric plug for protection against
possible electric shock hazards. It must be plugged into
a dedicated, grounded, electrical outlet. If only a two
prong electrical outlet is available, it is the responsi
of the customer to have it replaced with a dedica
properly grounded three prong electrical outle
avoid an electric shock hazard, do not u
circumstances:
Electrical Supply Requirements
ac, 60 Hz, 15 Amp., dedicated circuit
he warming drawer is supplied with a 40” (101.6 cm)
power cord with a three prong grounded plug.
total Connected Load 0.5 kW (4 Amp.)
• Cut or remove the third (ground)
•
•
The power supply requirements shown above are for
reference only. If they do not agree with those listed
on the product data label, use the requirements on the
product data label.
cord.
• Use an adapter plug.
• Use a power cord that is fra
It is the owner’s responsibility to ensure that the
electrical outlet is installed by a qualified electrician.
The electrical installation must comply with the latest
revision of the National Electric Code ANSI/NFPA 70
and local codes and ordinances.
• Immerse the power cord or plug or other
liquid.
• Connect the appliance to an extension cord.
NOtE: Use of a ground fault interrupter (GFI) is not
recommended.
•
If the electrical service provided does not meet the
product specification, or does not conform to the NEC
or local standards, do not proceed with the installation.
Call a licensed electrician to correct the electrical
service before proceeding.
•
•
Be certain to locate the electrical outlet in an
accessible location, so that the warming drawer may
be easily unplugged in the event that service becomes
necessary.
Keep the electrical cord away from hot surfaces.
Three prong plug
Three prong
grounded outlet
6
Installation Instructions
WARNING
Installing the Chassis
1. Grasp the warming drawer chassis on opposite
sides and slide it partially into the cabinet opening.
Temporarily support the chassis in place so that it will
not tilt or fall.
• To avoid personal injury caused by the appliance
falling forward when the drawer is opened, secure
the chassis to the cabinet and support platform as
instructed.
• Be certain that the power plug is disconnected from
2. From an adjoining cabinet, reach in behind the drawer
and pull the power cord until the plug is next to the
electrical outlet. Do not plug in the power cord at this
time.
the electrical outlet before installation.
• Verify that the electrical supply matches the ratings
found on the appliance data plate and the installation
specifications before proceeding.
3. After positioning the power cord and plug, slide the
chassis completely into the cabinet until the front frame
is positioned flush against the cabinet face.
Remove the Drawer
Remove the drawer from the appliance to allow access
to the mounting holes during installation, and to reduce
weight:
4. Use the screws provided to secure the warming drawer
chassis to the binet and support platform, insert them
into the mooles and tighten into place. You may
want to dprior to installing the mounting
screw
1. Pull the drawer out to the fully open position.
2. Push in on the locking tab on one side as you pull the
drawer up.
le, 9 places
3. When the drawer comes loose from the slide, repeat
the same process on the opposite side.
4. Grip the drawer on both sides and pull it free.
5. For safety, push both drawer slides into the drawe
opening.
StEP 2: Push
locking tab
Mounting Hole Locations - ERW, EWD, IWD, MRW and
MWD Series Models
(IWD series models do not have a flange around
the edge of the faceplate)
Mounting hole, 4 places
StEP 3: Pull up on
front of drawer
Mounting Hole Locations -
OWD24
Continued...
Style varies, EWD27 shown
7
Installation Instructions
Re-installing the Drawer
1. Pull the drawer slides all the way out of the drawer
opening.
Towel Rack Installation
(OWD24 Only)
Model OWD24 is designed so that it can be used as a
towel warmer if desired. Other models are not equipped for
this application. To use model OWD24 as a towel warmer,
you must install the towel rack included with the unit in the
bottom of the drawer.
2. Gently lower the drawer between the extended slides
until it is suspended by them.
3. Slide the back of the drawer mounting brackets under
the drawer mounting clips on the slides.
4. Push one side of the drawer down onto its locking tab,
until the tab locks into place.
to install the towel rack:
1. Open the drawer completely.
5. Repeat the same process on the opposite side.
2. Insert the towel rack into the drawer in the orientation
shown below.
6. Gently open and close the drawer to make sure that it
is properly installed.
StEP 3: Slide mounting
bracket under clip on slide
Clip on slide
Slide
3. Use the clamp and screw included with the rack to
attach it to the back of the drawer face as shown
below. There is a hole for the screw in the back of the
face plate near the bottom.
StEP 4: Push fr
of drawer down u
tabs lock into place
8
Installation Instructions
Warming Drawer Control Panel Layout
Verify Warming Drawer
Installation Checklist
Operation
WARNING
1. Connect power plug to the electrical outlet.
• To ensure a d proper installation, the following
checklist mpleted by the installer to
ensure e installation has been
over
2. Open the drawer and press the ON/OFF key on the
control panel.
3. Press the PROOF, LOW, MED and HIGH keys each
in turn. When you press each key, the indicator directly
above it should light. Leave the control panel set to
HIGH.
• Pe responsibility of the
portance of proper installation of
wer cannot be overemphasized.
4. Press the SELECt key. The 1 HOUR indicator should
light. Press and release the SELECt key three (3)
more times. Each time you press the SELECt ke
2 HOUR, 3 HOUR and 4 HOUR indicator light
come on. All lights should be on after press
SELECt key the third time.
orm has been installed according to the
s on page 6.
rly grounded, dedicated, three prong electrical
let has been installed for the appliance by a licensed
electrician. See page 6.
5. Press the "∞" key. The indicator li
should come on and the 1, 2 ,
lights should go out.
□ The chassis has been properly fastened to the support
platform and sides of the cabinet.
See page 7.
6. The warming drawer sho
You should begin to fe
drawer begin to heaten (10)
minutes.
□ The drawer has been properly installed. See page
8.
□ Model OWD24 for use as towel warmer: The towel rack
has been installed. See page 8.
7. When you have determihe heating
element is working, press N/OFF key.
□ Proper operation has been verified?
If the warming drawer does not operate properly, follow
these troubleshooting steps:
□ The warranty has been activated on-line or the
warranty card filled out completely and mailed?
•
Verify that the circuit breaker for the electrical outlet
is on and not tripped. Make sure the power plug is
connected.
□ Save these instructions for future reference.
•
•
Repeat the above tests.
If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not attempt
to repair the appliance yourself. Be sure to have the
model and serial numbers available when you call. See
page 1 for model/serial number location.
Dacor is not responsible for the cost of correcting problems
resulting from a faulty installation.
9
|
