CY7C1354C
CY7C1356C
9-Mbit (256K x 36/512K x 18)
Pipelined SRAM with NoBL™ Architecture
Functional Description[1]
Features
• Pin-compatible and functionally equivalent to ZBT™
• Supports 250-MHz bus operations with zero wait states
— Available speed grades are 250, 200, and 166 MHz
The CY7C1354C and CY7C1356C are 3.3V, 256K x 36 and
512K x 18 Synchronous pipelined burst SRAMs with No Bus
Latency™ (NoBL™) logic, respectively. They are designed to
support unlimited true back-to-back Read/Write operations
with no wait states. The CY7C1354C and CY7C1356C are
equipped with the advanced (NoBL) logic required to enable
consecutive Read/Write operations with data being trans-
ferred on every clock cycle. This feature dramatically improves
the throughput of data in systems that require frequent
Write/Read transitions. The CY7C1354C and CY7C1356C are
pin compatible and functionally equivalent to ZBT devices.
• Internally self-timed output buffer control to eliminate
the need to use asynchronous OE
• Fully registered (inputs and outputs) for pipelined
operation
• Byte Write capability
• Single 3.3V power supply (V
)
DD
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock. The
clock input is qualified by the Clock Enable (CEN) signal,
which when deasserted suspends operation and extends the
previous clock cycle.
• 3.3V or 2.5V I/O power supply (V
• Fast clock-to-output times
— 2.8 ns (for 250-MHz device)
)
DDQ
• Clock Enable (CEN) pin to suspend operation
• Synchronous self-timed writes
Write operations are controlled by the Byte Write Selects
• Available in lead-free 100-Pin TQFP package, lead-free
and non lead-free 119-Ball BGA package and 165-Ball
FBGA package
(BW –BW for CY7C1354C and BW –BW for CY7C1356C)
and a Write Enable (WE) input. All writes are conducted with
on-chip synchronous self-timed write circuitry.
a
d
a
b
• IEEE 1149.1 JTAG-Compatible Boundary Scan
• Burst capability–linear or interleaved burst order
• “ZZ” Sleep Mode option and Stop Clock option
Three synchronous Chip Enables (CE , CE , CE ) and an
1
2
3
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. In order to avoid bus
contention, the output drivers are synchronously tri-stated
during the data portion of a write sequence.
Logic Block Diagram–CY7C1354C (256K x 36)
ADDRESS
REGISTER 0
A0, A1, A
A1
A0
A1'
A0'
D1
D0
Q1
Q0
BURST
LOGIC
MODE
C
ADV/LD
C
CLK
CEN
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
O
O
S
U
D
A
T
U
T
P
T
P
E
N
S
U
T
U
T
ADV/LD
BWa
A
E
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
R
E
G
I
MEMORY
ARRAY
B
U
F
S
T
E
E
R
I
DQs
WRITE
DRIVERS
DQPa
DQPb
DQPc
DQPd
A
M
P
BWb
BWc
BWd
S
T
E
R
S
F
E
R
S
S
WE
E
E
N
G
INPUT
REGISTER 1
INPUT
REGISTER 0
E
E
OE
READ LOGIC
CE1
CE2
CE3
SLEEP
CONTROL
ZZ
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05538 Rev. *G
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised September 14, 2006
CY7C1354C
CY7C1356C
Pin Configurations
100-Pin TQFP Pinout
DQPc
DQc
DQc
1
2
3
4
5
6
7
8
NC
NC
NC
DDQ
1
2
3
4
5
6
7
8
A
NC
NC
78
DQPb
DQb
DQb
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
80
79
V
V
DDQ
V
V
V
NC
DQPa
DQa
DQa
DDQ
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DDQ
SS
V
V
V
SS
SS
SS
DQc
DQc
NC
NC
DQb
DQb
DQb
DQb
DQb
DQb
DQc
DQc
9
9
V
V
SS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
SS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V
SS
SS
V
V
DDQ
DDQ
V
V
DQa
DQa
V
NC
V
ZZ
DDQ
DDQ
DQc
DQc
NC
DQb
DQb
DQb
DQb
NC
V
SS
CY7C1354C
(256K × 36)
SS
CY7C1356C
(512K × 18)
V
V
DD
NC
DD
NC
V
NC
DD
DD
V
V
SS
SS
ZZ
DQa
DQa
DQd
DQb
DQb
DQa
DQa
DQd
V
V
DDQ
DDQ
V
V
V
DQa
DQa
NC
NC
V
V
DDQ
DDQ
V
V
SS
V
SS
SS
SS
DQd
DQd
DQd
DQd
DQa
DQa
DQb
DQb
DQa DQPb
DQa
NC
V
SS
V
V
SS
SS
SS
V
V
DDQ
V
DDQ
DDQ
DDQ
DQd
DQd
DQPd
DQa
DQa
DQPa
NC
NC
NC
NC
NC
NC
Document #: 38-05538 Rev. *G
Page 3 of 28
CY7C1354C
CY7C1356C
Pin Configurations (continued)
119-Ball BGA Pinout
CY7C1354C (256K × 36)
1
2
3
4
5
6
7
V
A
A
NC/18M
A
A
V
DDQ
A
DDQ
NC/576M
NC/1G
CE
A
A
A
ADV/LD
A
A
CE
A
NC
NC
DQ
B
C
D
2
3
V
DD
DQ
DQP
DQ
V
NC
V
DQP
DQ
c
c
SS
SS
SS
SS
SS
SS
b
b
DQ
V
V
CE
V
V
DQ
b
E
F
c
c
c
c
c
1
b
b
b
b
V
DQ
DQ
DQ
V
DQ
DQ
DQ
V
V
DDQ
OE
A
DDQ
DQ
DQ
G
H
J
BW
V
BW
V
c
b
c
b
DQ
DQ
WE
c
SS
b
SS
V
NC
V
NC
V
DDQ
DDQ
DD
DD
DD
DQ
DQ
V
CLK
NC
V
DQ
DQ
K
L
d
d
d
SS
SS
a
a
a
a
DQ
DQ
DQ
DQ
DQ
DQ
DQ
BW
BW
d
d
a
V
V
V
V
V
V
V
V
DDQ
M
N
P
CEN
A1
DDQ
d
SS
SS
SS
SS
SS
SS
a
a
DQ
DQ
DQ
d
d
a
a
DQ
DQP
A
A0
DQP
A
DQ
d
d
a
NC/144M
NC
MODE
A
V
NC/288M
ZZ
R
T
NC
A
DD
NC/72M
TMS
A
NC/36M
NC
V
TDI
TCK
TDO
V
U
DDQ
DDQ
CY7C1356C (512K x 18)
1
2
3
4
5
6
7
V
A
A
NC/18M
A
A
V
A
B
C
D
E
F
DDQ
DDQ
NC/576M
NC/1G
CE
A
A
A
A
A
NC
NC
NC
CE
ADV/LD
2
3
V
A
DD
DQ
NC
DQ
V
NC
V
DQP
b
SS
SS
SS
SS
SS
SS
a
NC
V
V
V
V
NC
DQ
CE
b
a
1
V
NC
DQ
DQ
V
OE
A
DDQ
a
DDQ
NC
V
V
NC
DQ
G
H
J
BW
V
b
SS
SS
a
b
DQ
V
NC
DQ
NC
V
WE
b
SS
a
V
NC
V
NC
V
DDQ
DD
DD
DD
DDQ
NC
DQ
V
CLK
NC
V
NC
DQ
K
L
b
SS
SS
a
DQ
NC
DQ
V
DQ
NC
BW
b
SS
a
a
V
V
V
V
V
NC
V
M
N
P
R
T
CEN
A1
DDQ
b
SS
SS
SS
SS
DDQ
DQ
NC
DQP
A
V
DQ
NC
b
SS
a
NC
V
A0
NC
A
DQ
b
SS
a
NC/144M
NC/72M
MODE
A
V
NC
A
NC/288M
ZZ
DD
A
NC/36M
TCK
A
V
TMS
TDI
TDO
NC
V
U
DDQ
DDQ
Document #: 38-05538 Rev. *G
Page 4 of 28
CY7C1354C
CY7C1356C
Pin Configurations (continued)
165-Ball FBGA Pinout
CY7C1354C (256K × 36)
1
2
A
3
4
5
6
7
8
9
A
10
A
11
NC
NC/576M
NC/1G
DQPc
ADV/LD
A
B
C
D
CE1
BWc
BWd
VSS
VDD
BWb
BWa
VSS
VSS
CE
CEN
WE
3
A
CE2
VDDQ
VDDQ
CLK
VSS
VSS
OE
VSS
VDD
NC/18M
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
A
NC
DQc
VSS
VSS
NC
DQb
DQPb
DQb
DQc
DQc
DQc
DQc
NC
DQc
DQc
DQc
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
DQb
DQb
DQb
NC
DQb
DQb
DQb
ZZ
E
F
G
H
J
NC
DQd
DQd
DQd
DQd
DQd
DQd
VDDQ
VDDQ
VDDQ
VDDQ
DQa
DQa
DQa
DQa
DQa
DQa
VDDQ
VDDQ
VDDQ
VDDQ
A
K
L
DQd
DQd
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
DQa
NC
A
DQa
DQPa
M
N
P
DQPd
NC/144M NC/72M
MODE NC/36M
TDI
TDO
NC/288M
A
A
TMS
A0
TCK
A
A
A
A
R
CY7C1356C (512K × 18)
1
NC/576M
NC/1G
NC
2
A
3
4
5
NC
6
CE
7
8
9
A
10
A
11
A
A
B
C
D
CE1
BWb
NC
CEN
ADV/LD
3
A
CE2
VDDQ
VDDQ
BWa
VSS
VSS
CLK
VSS
VSS
NC/18M
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
NC
A
WE
VSS
VSS
OE
VSS
VDD
NC
DQb
VSS
VDD
NC
NC
DQPa
DQa
NC
NC
NC
DQb
DQb
DQb
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
NC
NC
DQa
DQa
DQa
ZZ
E
F
NC
NC
G
H
J
NC
NC
NC
DQb
DQb
DQb
NC
VDDQ
VDDQ
VDDQ
VDDQ
DQa
DQa
DQa
NC
NC
VDDQ
VDDQ
VDDQ
VDDQ
A
NC
K
L
NC
NC
DQb
NC
NC
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
NC
A1
VSS
NC
VDD
VSS
A
DQa
NC
A
NC
NC
M
N
P
DQPb
NC/144M NC/72M
MODE NC/36M
TDI
TDO
NC/288M
A
A
TMS
A0
TCK
A
A
A
A
R
Document #: 38-05538 Rev. *G
Page 5 of 28
CY7C1354C
CY7C1356C
Pin Definitions
Pin Name
I/O Type
Pin Description
Address Inputs used to select one of the address locations. Sampled at the rising edge of
A0, A1
Input-
A
Synchronous the CLK.
Input- Byte Write Select Inputs, active LOW. Qualified with WE to conduct writes to the SRAM.
Synchronous Sampled on the rising edge of CLK. BW controls DQ and DQP , BW controls DQ and DQP ,
BW ,BW ,
BW ,BW ,
a
b
c
d
a
a
a
b
b
b
BW controls DQ and DQP , BW controls DQ and DQP .
c
c
c
d
d
d
WE
Input-
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW.
Synchronous This signal must be asserted LOW to initiate a write sequence.
ADV/LD
Input- Advance/Load Input used to advance the on-chip address counter or load a new address.
Synchronous When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a
new address can be loaded into the device for an access. After being deselected, ADV/LD should
be driven LOW in order to load a new address.
CLK
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN is active LOW.
CE
CE
CE
Input-
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
1
2
3
Synchronous CE and CE to select/deselect the device.
2
3
Input-
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
Synchronous with CE and CE to select/deselect the device.
1
3
Input-
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction with
Synchronous CE and CE to select/deselect the device.
1
2
OE
Input-
Output Enable, active LOW. Combined with the synchronous logic block inside the device to
Asynchronous control the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs.
When deasserted HIGH, I/O pins are tri-stated, and act as input data pins. OE is masked during
the data portion of a Write sequence, during the first clock when emerging from a deselected
state and when the device has been deselected.
CEN
Input-
Clock Enable Input, active LOW. When asserted LOW the clock signal is recognized by the
Synchronous SRAM. When deasserted HIGH the clock signal is masked. Since deasserting CEN does not
deselect the device, CEN can be used to extend the previous cycle when required.
DQ
I/O-
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is triggered
S
Synchronous by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by addresses during the previous clock rise of the Read cycle. The direction of the pins
is controlled by OE and the internal control logic. When OE is asserted LOW, the pins can behave
as outputs. When HIGH, DQ –DQ are placed in a tri-state condition. The outputs are automat-
a
d
ically tri-stated during the data portion of a write sequence, during the first clock when emerging
from a deselected state, and when the device is deselected, regardless of the state of OE.
DQP
I/O-
Bidirectional Data Parity I/O lines. Functionally, these signals are identical to DQ
During
[a:d].
X
Synchronous write sequences, DQP is controlled by BW , DQP is controlled by BW , DQP is controlled by
a
a
b
b
c
BW , and DQP is controlled by BW .
c
d
d
MODE
TDO
Input Strap Pin Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order.
Pulled LOW selects the linear burst order. MODE should not change states during operation.
When left floating MODE will default HIGH, to an interleaved burst order.
JTAG serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK.
output
Synchronous
TDI
JTAG serial input Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK.
Synchronous
TMS
TCK
Test Mode Select This pin controls the Test Access Port state machine. Sampled on the rising edge of TCK.
Synchronous
JTAG-Clock Clock input to the JTAG circuitry.
Power Supply Power supply inputs to the core of the device.
I/O Power Supply Power supply for the I/O circuitry.
V
V
V
DD
DDQ
SS
Ground
Ground for the device. Should be connected to ground of the system.
Document #: 38-05538 Rev. *G
Page 6 of 28
CY7C1354C
CY7C1356C
Pin Definitions (continued)
Pin Name
NC
I/O Type
Pin Description
No connects. This pin is not connected to the die.
–
–
NC (18, 36,
72, 144, 288,
576, 1G)
These pins are not connected. They will be used for expansion to the 18M, 36M, 72M, 144M
288M, 576M and 1G densities.
ZZ
Input-
ZZ “sleep” Input. This active HIGH input places the device in a non-time-critical “sleep”
Asynchronous condition with data integrity preserved. For normal operation, this pin has to be LOW or left
floating. ZZ pin has an internal pull-down.
Burst Read Accesses
Functional Overview
The CY7C1354C and CY7C1356C have an on-chip burst
counter that allows the user the ability to supply a single
address and conduct up to four Reads without reasserting the
address inputs. ADV/LD must be driven LOW in order to load
a new address into the SRAM, as described in the Single Read
Access section above. The sequence of the burst counter is
determined by the MODE input signal. A LOW input on MODE
selects a linear burst mode, a HIGH selects an interleaved
burst sequence. Both burst counters use A0 and A1 in the
burst sequence, and will wrap around when incremented suffi-
ciently. A HIGH input on ADV/LD will increment the internal
burst counter regardless of the state of chip enables inputs or
WE. WE is latched at the beginning of a burst cycle. Therefore,
the type of access (Read or Write) is maintained throughout
the burst sequence.
The CY7C1354C and CY7C1356C are synchronous-pipelined
Burst NoBL SRAMs designed specifically to eliminate wait
states during Write/Read transitions. All synchronous inputs
pass through input registers controlled by the rising edge of
the clock. The clock signal is qualified with the Clock Enable
input signal (CEN). If CEN is HIGH, the clock signal is not
recognized and all internal states are maintained. All
synchronous operations are qualified with CEN. All data
outputs pass through output registers controlled by the rising
edge of the clock. Maximum access delay from the clock rise
(t ) is 2.8 ns (250-MHz device).
CO
Accesses can be initiated by asserting all three Chip Enables
(CE , CE , CE ) active at the rising edge of the clock. If Clock
1
2
3
Enable (CEN) is active LOW and ADV/LD is asserted LOW,
the address presented to the device will be latched. The
access can either be a Read or Write operation, depending on
Single Write Accesses
the status of the Write Enable (WE). BW
conduct Byte Write operations.
can be used to
Write access are initiated when the following conditions are
[d:a]
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE , CE ,
1
2
and CE are ALL asserted active, and (3) the Write signal WE
Write operations are qualified by the Write Enable (WE). All
Writes are simplified with on-chip synchronous self-timed
Write circuitry.
3
is asserted LOW. The address presented to A –A is loaded
0
16
into the Address Register. The write signals are latched into
the Control Logic block.
Three synchronous Chip Enables (CE , CE , CE ) and an
1
2
3
On the subsequent clock rise the data lines are automatically
tri-stated regardless of the state of the OE input signal. This
asynchronous Output Enable (OE) simplify depth expansion.
All operations (Reads, Writes, and Deselects) are pipelined.
ADV/LD should be driven LOW once the device has been
deselected in order to load a new address for the next
operation.
allows the external logic to present the data on DQ
and DQP
(DQ
/DQP
for CY7C1354C and DQ /DQP
for
a,b,c,d
a,b,c,d
a,b
a,b
CY7C1356C). In addition, the address for the subsequent
access (Read/Write/Deselect) is latched into the address
register (provided the appropriate control signals are
asserted).
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE , CE ,
On the next clock rise the data presented to DQ
and DQP
1
2
and CE are ALL asserted active, (3) the Write Enable input
(DQ
/DQP
for CY7C1354C and DQ /DQP
for
3
a,b,c,d
a,b,c,d
a,b
a,b
signal WE is deasserted HIGH, and (4) ADV/LD is asserted
LOW. The address presented to the address inputs is latched
into the address register and presented to the memory core
and control logic. The control logic determines that a read
access is in progress and allows the requested data to
propagate to the input of the output register. At the rising edge
of the next clock the requested data is allowed to propagate
through the output register and onto the data bus within 2.8 ns
(250-MHz device) provided OE is active LOW. After the first
clock of the read access the output buffers are controlled by
OE and the internal control logic. OE must be driven LOW in
order for the device to drive out the requested data. During the
second clock, a subsequent operation (Read/Write/Deselect)
can be initiated. Deselecting the device is also pipelined.
Therefore, when the SRAM is deselected at clock rise by one
of the chip enable signals, its output will tri-state following the
next clock rise.
CY7C1356C) (or a subset for byte write operations, see Write
Cycle Description table for details) inputs is latched into the
device and the Write is complete.
The data written during the Write operation is controlled by BW
(BW
for CY7C1354C and BW
for CY7C1356C)
a,b,c,d
a,b
signals. The CY7C1354C/CY7C1356C provides Byte Write
capability that is described in the Write Cycle Description table.
Asserting the Write Enable input (WE) with the selected Byte
Write Select (BW) input will selectively write to only the desired
bytes. Bytes not selected during a Byte Write operation will
remain unaltered. A synchronous self-timed write mechanism
has been provided to simplify the Write operations. Byte Write
capability has been included in order to greatly simplify
Read/Modify/Write sequences, which can be reduced to
simple Byte Write operations.
Document #: 38-05538 Rev. *G
Page 7 of 28
CY7C1354C
CY7C1356C
Because the CY7C1354C and CY7C1356C are common I/O
devices, data should not be driven into the device while the
outputs are active. The Output Enable (OE) can be deasserted
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
HIGH before presenting data to the DQ
and DQP
(DQ
/DQP
for CY7C1354C and DQ /DQP
for
the “sleep” mode. CE , CE , and CE must remain inactive for
a,b,c,d
a,b,c,d
a,b
a,b
1
2
3,
CY7C1356C) inputs. Doing so will tri-state the output drivers.
As a safety precaution, DQ (DQ /DQP for
CY7C1354C and DQ /DQP
automatically tri-stated during the data portion of a write cycle,
regardless of the state of OE.
the duration of t
after the ZZ input returns LOW.
ZZREC
and DQP
a,b,c,d
a,b,c,d
Interleaved Burst Address Table
(MODE = Floating or VDD
for CY7C1356C) are
a,b
a,b
)
First
Address
Second
Address
Third
Address
Fourth
Address
Burst Write Accesses
A1,A0
00
A1,A0
01
A1,A0
10
A1,A0
11
The CY7C1354C/CY7C1356C has an on-chip burst counter
that allows the user the ability to supply a single address and
conduct up to four WRITE operations without reasserting the
address inputs. ADV/LD must be driven LOW in order to load
the initial address, as described in the Single Write Access
section above. When ADV/LD is driven HIGH on the subse-
01
00
11
10
10
11
00
01
11
10
01
00
Linear Burst Address Table (MODE = GND)
quent clock rise, the chip enables (CE , CE , and CE ) and
1
2
3
WE inputs are ignored and the burst counter is incremented.
The correct BW (BW for CY7C1354C and BW for
First
Address
Second
Address
Third
Address
Fourth
Address
a,b,c,d
a,b
CY7C1356C) inputs must be driven in each cycle of the burst
write in order to write the correct bytes of data.
A1,A0
00
A1,A0
01
A1,A0
10
A1,A0
11
01
10
11
00
Sleep Mode
10
11
11
00
00
01
01
10
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
ZZ Mode Electrical Characteristics
Parameter
Description
Sleep mode standby current
Device operation to ZZ
ZZ recovery time
Test Conditions
Min.
Max.
50
Unit
mA
ns
I
t
t
t
t
ZZ > V − 0.2V
DD
ZZ > V − 0.2V
DDZZ
2t
ZZS
DD
CYC
ZZ < 0.2V
2t
ns
ZZREC
ZZI
CYC
ZZ active to sleep current
This parameter is sampled
This parameter is sampled
2t
ns
CYC
ZZ Inactive to exit sleep current
0
ns
RZZI
Truth Table[2, 3, 4, 5, 6, 7, 8]
Address
Used
Operation
Deselect Cycle
CE ZZ ADV/LD WE BWx OE CEN CLK
DQ
None
None
H
X
L
L
L
L
L
L
L
L
L
L
H
L
X
X
H
X
H
X
L
X
X
X
X
X
X
L
X
X
L
L
L
L
L
L
L
L
L
L-H
L-H
Tri-State
Tri-State
Continue Deselect Cycle
Read Cycle (Begin Burst)
Read Cycle (Continue Burst)
NOP/Dummy Read (Begin Burst)
Dummy Read (Continue Burst)
Write Cycle (Begin Burst)
Write Cycle (Continue Burst)
External
Next
L-H Data Out (Q)
L-H Data Out (Q)
X
L
H
L
L
External
Next
H
H
X
X
L-H
L-H
L-H
L-H
Tri-State
Tri-State
X
L
H
L
External
Next
Data In (D)
Data In (D)
X
H
X
L
Notes:
2. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = L signifies at least one Byte Write Select is active, BWx =
Valid signifies that the desired Byte Write Selects are asserted, see Write Cycle Description table for details.
3. Write is defined by WE and BW . See Write Cycle Description table for details.
X
4. When a write cycle is detected, all I/Os are tri-stated, even during Byte Writes.
5. The DQ and DQP pins are controlled by the current cycle and the OE signal.
6. CEN = H inserts wait states.
7. Device will power-up deselected and the I/Os in a tri-state condition, regardless of OE.
8. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle DQs and DQP = Tri-state when OE
X
is inactive or when the device is deselected, and DQs = data when OE is active.
Document #: 38-05538 Rev. *G
Page 8 of 28
CY7C1354C
CY7C1356C
Truth Table[2, 3, 4, 5, 6, 7, 8]
Address
Used
Operation
NOP/WRITE ABORT (Begin Burst)
WRITE ABORT (Continue Burst)
IGNORE CLOCK EDGE (Stall)
SLEEP MODE
CE ZZ ADV/LD WE BWx OE CEN CLK
DQ
Tri-State
Tri-State
-
None
Next
L
X
X
X
L
L
L
H
X
X
L
X
X
X
H
H
X
X
X
X
X
X
L
L
L-H
L-H
L-H
X
Current
None
L
H
X
H
Tri-State
Partial Write Cycle Description[2, 3, 4, 9]
Function (CY7C1354C)
Read
WE
BW
BW
BW
BW
a
d
c
b
H
X
X
H
H
H
H
L
X
H
H
L
X
H
L
Write –No bytes written
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
H
H
H
L
Write Byte a – (DQ and DQP )
a
a
Write Byte b – (DQ and DQP )
H
L
b
b
Write Bytes b, a
Write Byte c – (DQ and DQP )
L
H
H
L
H
L
c
c
Write Bytes c, a
Write Bytes c, b
Write Bytes c, b, a
L
L
H
L
L
L
Write Byte d – (DQ and DQP )
H
H
H
H
L
H
H
L
H
L
d
d
Write Bytes d, a
Write Bytes d, b
Write Bytes d, b, a
Write Bytes d, c
Write Bytes d, c, a
Write Bytes d, c, b
Write All Bytes
L
L
H
L
L
L
L
H
H
L
H
L
L
L
L
L
H
L
L
L
L
Partial Write Cycle Description[2, 3, 4, 9]
Function (CY7C1356C)
Read
WE
H
L
BW
BW
x
b
a
x
H
H
L
Write – No Bytes Written
Write Byte a − (DQ and DQP
H
L
L
a
a)
Write Byte b – (DQ and DQP
L
H
L
b
b)
Write Both Bytes
L
L
Note:
9. Table only lists a partial listing of the byte write combinations. Any combination of BW is valid. Appropriate write will be done based on which byte write is active.
X
Document #: 38-05538 Rev. *G
Page 9 of 28
CY7C1354C
CY7C1356C
Test MODE SELECT (TMS)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this ball unconnected if the TAP is not used. The ball is
pulled up internally, resulting in a logic HIGH level.
The CY7C1354C/CY7C1356C incorporates a serial boundary
scan test access port (TAP) in the BGA package only. The
TQFP package does not offer this functionality. This part
operates in accordance with IEEE Standard 1149.1-1900, but
doesn’t have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note the TAP controller
functions in a manner that does not conflict with the operation
of other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3V or 2.5V I/O logic levels.
Test Data-In (TDI)
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. TDI
is internally pulled up and can be unconnected if the TAP is
unused in an application. TDI is connected to the most signif-
icant bit (MSB) of any register. (See Tap Controller Block
Diagram.)
The CY7C1354C/CY7C1356C contains a TAP controller,
instruction register, boundary scan register, bypass register,
and ID register.
Test Data-Out (TDO)
Disabling the JTAG Feature
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See Tap Controller State Diagram.)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(V ) to prevent clocking of the device. TDI and TMS are inter-
SS
nally pulled up and may be unconnected. They may alternately
be connected to V through a pull-up resistor. TDO should be
DD
left unconnected. Upon power-up, the device will come up in
a reset state which will not interfere with the operation of the
device.
TAP Controller Block Diagram
0
Bypass Register
TAP Controller State Diagram
2
1
0
0
0
TEST-LOGIC
1
Selection
Circuitry
RESET
0
Instruction Register
31 30 29
Identification Register
Selection
Circuitry
TDI
TDO
.
.
.
2
1
1
1
1
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
0
0
0
x
.
.
.
.
.
2
1
1
1
CAPTURE-DR
CAPTURE-IR
Boundary Scan Register
0
0
SHIFT-DR
0
SHIFT-IR
0
1
1
TCK
TMS
1
1
EXIT1-DR
EXIT1-IR
TAP CONTROLLER
0
0
PAUSE-DR
0
PAUSE-IR
0
1
1
Performing a TAP Reset
0
0
EXIT2-DR
1
EXIT2-IR
1
A RESET is performed by forcing TMS HIGH (V ) for five
DD
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
UPDATE-DR
UPDATE-IR
1
0
1
0
At power-up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
Document #: 38-05538 Rev. *G
Page 10 of 28
CY7C1354C
CY7C1356C
TDI and TDO balls as shown in the Tap Controller Block
Diagram. Upon power-up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
through the instruction register through the TDI and TDO balls.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with all
0s. EXTEST is not implemented in this SRAM TAP controller,
and therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-0 instruction.
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board-level serial test data path.
Bypass Register
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between
the two instructions. Unlike the SAMPLE/PRELOAD
instruction, EXTEST places the SRAM outputs in a High-Z
state.
(V ) when the BYPASS instruction is executed.
SS
Boundary Scan Register
IDCODE
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the I/O ring.
The IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a test
logic reset state.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI and the LSB is connected to TDO.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and output pins is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
will undergo a transition. The TAP may then try to capture a
signal while in transition (metastable state). This will not harm
the device, but there is no guarantee as to the value that will
be captured. Repeatable results may not be possible.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and should not be used. The other five instruc-
tions are described in detail below.
The TAP controller used in this SRAM is not fully compliant to
the 1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture set-up plus
hold times (t and t ). The SRAM clock input might not be
captured correctly if there is no way in a design to stop (or
slow) the clock during a SAMPLE/PRELOAD instruction. If this
is an issue, it is still possible to capture all other signals and
simply ignore the value of the CK and CK# captured in the
boundary scan register.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the I/O
buffers. The SRAM does not implement the 1149.1 commands
EXTEST or INTEST or the PRELOAD portion of
SAMPLE/PRELOAD; rather, it performs a capture of the I/O
ring when these instructions are executed.
CS
CH
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO pins.
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
Document #: 38-05538 Rev. *G
Page 11 of 28
CY7C1354C
CY7C1356C
PRELOAD allows an initial data pattern to be placed at the
latched parallel outputs of the boundary scan register cells
prior to the selection of another boundary scan test operation.
register is placed between the TDI and TDO balls. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
The shifting of data for the SAMPLE and PRELOAD phases
can occur concurrently when required—that is, while data
captured is shifted out, the preloaded data can be shifted in.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
TH
CYC
TL
t
t
t
t
TMSS
TDIS
TMSH
Test Mode Select
(TMS)
TDIH
Test Data-In
(TDI)
t
TDOV
t
TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
[10, 11]
TAP AC Switching Characteristics Over the Operating Range
Parameter
Clock
Description
Min.
Max.
Unit
t
t
t
t
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH time
TCK Clock LOW time
50
ns
MHz
ns
TCYC
TF
20
20
20
TH
ns
TL
Output Times
t
t
TCK Clock LOW to TDO Valid
TCK Clock LOW to TDO Invalid
10
ns
ns
TDOV
TDOX
0
Set-up Times
t
t
t
TMS Set-up to TCK Clock Rise
TDI Set-up to TCK Clock Rise
Capture Set-up to TCK Rise
5
5
5
ns
ns
ns
TMSS
TDIS
CS
Hold Times
t
t
t
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
TMSH
TDIH
CH
Capture Hold after Clock Rise
Notes:
10. t and t refer to the set-up and hold time requirements of latching data from the boundary scan register.
CS
CH
11. Test conditions are specified using the load in TAP AC test Conditions. t /t = 1 ns.
R
F
Document #: 38-05538 Rev. *G
Page 12 of 28
CY7C1354C
CY7C1356C
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels ................................................ V to 3.3V
Input pulse levels.................................................V to 2.5V
SS
SS
Input rise and fall times................................................... 1 ns
Input timing reference levels...........................................1.5V
Output reference levels...................................................1.5V
Test load termination supply voltage...............................1.5V
Input rise and fall time .....................................................1 ns
Input timing reference levels......................................... 1.25V
Output reference levels ................................................ 1.25V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.5V
1.25V
50Ω
50Ω
TDO
TDO
ZO= 50Ω
ZO= 50Ω
20pF
20pF
TAP DC Electrical Characteristics And Operating Conditions
[12]
(0°C < TA < +70°C; V = 3.3V ±0.165V unless otherwise noted)
DD
Parameter
Description
Test Conditions
Min.
2.4
2.0
2.9
2.1
Max.
Unit
V
V
V
V
V
V
V
Output HIGH Voltage
I
I
I
= –4.0 mA, V
= –1.0 mA, V
= –100 µA
= 3.3V
= 2.5V
OH1
OH
OH
OH
DDQ
DDQ
V
Output HIGH Voltage
Output LOW Voltage
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
V
V
V
V
V
V
V
V
V
V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
= 3.3V
= 2.5V
V
OH2
OL1
OL2
IH
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
DDQ
V
I
= 8.0 mA
= 100 µA
0.4
0.4
0.2
0.2
V
OL
OL
V
I
V
V
2.0
1.7
V
V
+ 0.3
V
DD
DD
+ 0.3
V
–0.3
–0.3
–5
0.8
V
IL
0.7
5
V
I
GND < V < V
DDQ
µA
X
IN
Identification Register Definitions
Instruction Field
Revision Number (31:29)
Cypress Device ID (28:12)
Cypress JEDEC ID (11:1)
ID Register Presence (0)
CY7C1354C
000
CY7C1356C
Description
Reserved for version number.
000
[13]
01011001000100110 01011001000010110 Reserved for future use.
00000110100
1
00000110100
1
Allows unique identification of SRAM vendor.
Indicate the presence of an ID register.
Notes:
12. All voltages referenced to V (GND).
SS
13. Bit #24 is “1” in the Register Definitions for both 2.5V and 3.3V versions of this device.
Document #: 38-05538 Rev. *G
Page 13 of 28
CY7C1354C
CY7C1356C
Scan Register Sizes
Register Name
Bit Size (x36)
Bit Size (x18)
Instruction
3
3
Bypass
1
1
ID
32
69
69
32
69
69
Boundary Scan Order (119-ball BGA package)
Boundary Scan Order (165-ball FBGA package)
Identification Codes
Instruction
EXTEST
Code
Description
000 Captures the Input/Output ring contents. Places the boundary scan register between the TDI and
TDO. Forces all SRAM outputs to High-Z state.
IDCODE
001 Loads the ID register with the vendor ID code and places the register between TDI and TDO. This
operation does not affect SRAM operation.
SAMPLE Z
010 Captures the Input/Output contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011 Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD 100 Captures the Input/Output ring contents. Places the boundary scanregister between TDI and TDO.
Does not affect the SRAM operation.
RESERVED
RESERVED
BYPASS
101 Do Not Use: This instruction is reserved for future use.
110 Do Not Use: This instruction is reserved for future use.
111 Places the bypass register between TDI and TDO. This operation does not affect SRAM operation.
Document #: 38-05538 Rev. *G
Page 14 of 28
CY7C1354C
CY7C1356C
Boundary Scan Exit Order (256K × 36)
Boundary Scan Exit Order (256K × 36) (continued)
Bit #
1
119-ball ID
K4
H4
M4
F4
165-ball ID
B6
Bit #
44
119-ball ID
165-ball ID
L2
K1
N2
N1
M2
L1
K2
J2
2
B7
45
3
A7
46
M2
M1
L1
K1
J1
4
B8
47
5
B4
G4
C3
B3
D6
H7
G6
E6
D7
E7
F6
A8
48
6
A9
49
7
B10
A10
C11
E10
F10
G10
D10
D11
E11
F11
G11
H11
J10
K10
L10
M10
J11
K11
L11
M11
N11
R11
R10
P10
R9
50
K2
8
51
Not Bonded
(Preset to 1)
Not Bonded
(Preset to 1)
9
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
H1
G2
E2
D1
H2
G1
F2
E1
D2
C2
A2
E4
B2
L3
G2
F2
E2
D2
G1
F1
E1
D1
C1
B2
A2
A3
B3
B4
A4
A5
B5
A6
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
G7
H6
T7
K7
L6
N6
P7
N7
M6
L7
G3
G5
L5
K6
P6
T4
B6
A3
C5
B5
A5
C6
A6
P4
N4
R6
T5
P9
R8
P8
R6
P6
R4
P4
T3
R3
R2
R3
P2
P1
P3
R1
N1
L2
Document #: 38-05538 Rev. *G
Page 15 of 28
CY7C1354C
CY7C1356C
Boundary Scan Exit Order (512K × 18)
Boundary Scan Exit Order (512K × 18) (continued)
Bit #
1
119-ball ID
165-ball ID
B6
Bit #
39
119-ball ID
165-ball ID
K4
H4
M4
F4
B4
G4
C3
B3
T2
T3
R2
R3
R3
P3
R1
2
B7
40
3
A7
41
4
B8
42
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
5
A8
43
44
45
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
6
A9
7
B10
A10
A11
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
8
9
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
10
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
46
47
48
49
50
51
P2
N1
M2
L1
N1
M1
L1
K1
J1
11
12
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
K2
13
14
15
16
17
18
19
20
21
22
23
D6
E7
F6
G7
H6
T7
K7
L6
C11
D11
E11
F11
G11
H11
J10
K10
L10
M10
Not Bonded
(Preset to 1)
Not Bonded
(Preset to 1)
52
53
54
55
56
H1
G2
E2
D1
G2
F2
E2
D2
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
N6
P7
57
58
59
60
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
24
25
26
27
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
61
62
63
64
65
C2
A2
E4
B2
B2
A2
A3
B3
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0)
28
29
30
31
32
33
34
35
36
37
38
T6
A3
C5
B5
A5
C6
A6
P4
N4
R6
T5
R11
R10
P10
R9
P9
Not Bonded
(Preset to 0
Not Bonded
(Preset to 0)
66
67
G3
Not Bonded
(Preset to 0)
Not Bonded
(Preset to 0
A4
R8
P8
68
69
L5
B6
B5
A6
R6
P6
R4
P4
Document #: 38-05538 Rev. *G
Page 16 of 28
CY7C1354C
CY7C1356C
DC Input Voltage ................................... –0.5V to V + 0.5V
Maximum Ratings
DD
Current into Outputs (LOW)......................................... 20 mA
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Static Discharge Voltage...........................................> 2001V
(per MIL-STD-883, Method 3015)
Storage Temperature .................................–65°C to +150°C
Latch-up Current.....................................................> 200 mA
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Operating Range
Supply Voltage on V Relative to GND........ –0.5V to +4.6V
DD
Ambient
Supply Voltage on V
Relative to GND ......–0.5V to +V
Range
Temperature
V
V
DDQ
DDQ
DD
DD
DC to Outputs in Tri-State................... –0.5V to V
+ 0.5V
Commercial 0°C to +70°C 3.3V –5%/+10% 2.5V – 5%
to V
DDQ
DD
Industrial
–40°C to +85°C
[14, 15]
Electrical Characteristics Over the Operating Range
Parameter
Description
Power Supply Voltage
I/O Supply Voltage
Test Conditions
Min.
3.135
3.135
2.375
2.4
Max.
Unit
V
V
3.6
DD
V
V
V
V
V
I
for 3.3V I/O
for 2.5V I/O
V
V
DDQ
DD
2.625
V
Output HIGH Voltage
Output LOW Voltage
Input HIGH Voltage
for 3.3V I/O, I = −4.0 mA
V
OH
OL
IH
OH
for 2.5V I/O, I = −1.0 mA
2.0
V
OH
for 3.3V I/O, I = 8.0 mA
0.4
0.4
V
OL
for 2.5V I/O, I = 1.0 mA
V
OL
for 3.3V I/O
for 2.5V I/O
for 3.3V I/O
for 2.5V I/O
2.0
1.7
V
V
+ 0.3V
V
DD
DD
+ 0.3V
0.8
V
[16]
Input LOW Voltage
–0.3
–0.3
–5
V
IL
0.7
V
Input Leakage Current GND ≤ V ≤ V
except ZZ and MODE
5
µA
X
I
DDQ
Input Current of MODE Input = V
–30
–5
µA
µA
SS
Input = V
5
DD
Input Current of ZZ
Input = V
Input = V
µA
SS
DD
30
5
µA
I
I
Output Leakage Current GND ≤ V ≤ V
Output Disabled
–5
µA
OZ
I
DDQ,
V
Operating Supply
V
f = f
= Max., I
= 0 mA,
4-ns cycle, 250 MHz
5-ns cycle, 200 MHz
6-ns cycle, 166 MHz
250
220
180
130
120
110
40
mA
mA
mA
mA
mA
mA
mA
DD
DD
DD
OUT
= 1/t
CYC
MAX
I
Automatic CE
Power-down
Current—TTL Inputs
Max. V , Device Deselected, 4-ns cycle, 250 MHz
DD
SB1
V
≥ V or V ≤ V , f = f
IN IN IL MAX
IH
= 1/t
CYC
5-ns cycle, 200 MHz
6-ns cycle, 166 MHz
I
I
Automatic CE
Power-down
Current—CMOS Inputs f = 0
Max. V , Device Deselected, All speed grades
DD
SB2
V
≤ 0.3V or V > V
− 0.3V,
IN
IN
DDQ
Automatic CE
Power-down
Current—CMOS Inputs f = f
Max. V , Device Deselected, 4-ns cycle, 250 MHz
120
110
100
40
mA
mA
mA
mA
SB3
DD
V
≤ 0.3V or V > V
− 0.3V,
IN
IN
DDQ
5-ns cycle, 200 MHz
6-ns cycle, 166 MHz
= 1/t
MAX
CYC
I
Automatic CE
Max. V , Device Deselected, All speed grades
DD
SB4
Power-down
Current—TTL Inputs
V
≥ V or V ≤ V , f = 0
IN
IH
IN
IL
Notes:
14. Overshoot: V (AC) < V +1.5V (Pulse width less than t
/2), undershoot: V (AC)> –2V (Pulse width less than t /2).
CYC
IH
DD
CYC
IL
15. T
: Assumes a linear ramp from 0V to V
(min.) within 200 ms. During this time V < V and V
< V
.
Power-up
IH
DD
DDQ
DD
DD
16. Tested initially and after any design or process changes that may affect these parameters.
Document #: 38-05538 Rev. *G
Page 17 of 28
CY7C1354C
CY7C1356C
Capacitance[16]
100 TQFP
Max.
119 BGA
Max.
165 FBGA
Parameter
Description
Test Conditions
Max.
Unit
pF
C
C
C
Input Capacitance
T = 25°C, f = 1 MHz,
5
5
5
5
5
7
5
5
7
IN
A
V
= 3.3V V
= 2.5V
DD
DDQ
Clock Input Capacitance
Input/Output Capacitance
pF
CLK
I/O
pF
Thermal Resistance[16]
100 TQFP
119 BGA
Max.
165 FBGA
Max.
Parameter
Description
Test Conditions
Max.
Unit
Θ
Thermal Resistance
(Junction to Ambient)
Test conditions follow standard
test methods and procedures for
measuring thermal impedance,
per EIA/JESD51.
29.41
34.1
16.8
°C/W
JA
Θ
Thermal Resistance
(Junction to Case)
6.13
14.0
3.0
°C/W
JC
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
R = 50Ω
L
5 pF
R = 351Ω
≤ 1 ns
≤ 1 ns
INCLUDING
JIG AND
SCOPE
V = 1.5V
T
(a)
(b)
(c)
2.5V I/O Test Load
R = 1667Ω
2.5V
OUTPUT
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
R = 50Ω
L
5 pF
R = 1538Ω
≤ 1 ns
≤ 1 ns
INCLUDING
JIG AND
SCOPE
V = 1.25V
T
(a)
(b)
(c)
Document #: 38-05538 Rev. *G
Page 18 of 28
CY7C1354C
CY7C1356C
[18, 19]
Switching Characteristics Over the Operating Range
–250
–200
–166
Parameter
Description
(typical) to the First Access Read or Write
CC
Min.
Max.
Min.
Max.
Min.
Max.
Unit
[17]
t
V
1
1
1
ms
Power
Clock
t
Clock Cycle Time
4.0
5
6
ns
MHz
ns
CYC
F
Maximum Operating Frequency
Clock HIGH
250
2.8
200
3.2
166
3.5
MAX
t
t
t
t
1.8
1.8
2.0
2.0
2.4
2.4
CH
Clock LOW
ns
CL
OE LOW to Output Valid
ns
EOV
CLZ
[20, 21, 22]
Clock to Low-Z
1.25
1.5
1.5
ns
Output Times
t
t
t
t
t
t
t
Data Output Valid after CLK Rise
OE LOW to Output Valid
2.8
2.8
3.2
3.2
3.5
3.5
ns
ns
ns
ns
ns
ns
ns
CO
EOV
DOH
CHZ
CLZ
Data Output Hold after CLK Rise
1.25
1.25
1.25
1.5
1.5
1.5
1.5
1.5
1.5
[20, 21, 22]
Clock to High-Z
2.8
2.8
3.2
3.2
3.5
3.5
[20, 21, 22]
Clock to Low-Z
[20, 21, 22]
OE HIGH to Output High-Z
EOHZ
EOLZ
[20, 21, 22]
0
0
0
OE LOW to Output Low-Z
Set-up Times
t
t
t
t
t
t
Address Set-up before CLK Rise
Data Input Set-up before CLK Rise
CEN Set-up before CLK Rise
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
1.5
ns
ns
ns
ns
ns
ns
AS
DS
CENS
WES
ALS
CES
WE, BW Set-up before CLK Rise
x
ADV/LD Set-up before CLK Rise
Chip Select Set-up
Hold Times
t
t
t
t
t
t
Address Hold after CLK Rise
Data Input Hold after CLK Rise
CEN Hold after CLK Rise
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
AH
DH
CENH
WEH
ALH
CEH
WE BW Hold after CLK Rise
,
x
ADV/LD Hold after CLK Rise
Chip Select Hold after CLK Rise
Notes:
17. This part has a voltage regulator internally; t
is the time power needs to be supplied above V minimum initially, before a Read or Write operation can be
DD
power
initiated.
18. Timing reference level is 1.5V when V
= 3.3V and is 1.25V when V
= 2.5V.
DDQ
DDQ
19. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
20. t , t , t , and t are specified with AC test conditions shown in (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
CHZ CLZ EOLZ
EOHZ
21. At any given voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same
EOHZ
EOLZ
CHZ
CLZ
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
22. This parameter is sampled and not 100% tested.
Document #: 38-05538 Rev. *G
Page 19 of 28
CY7C1354C
CY7C1356C
Switching Waveforms
[23, 24, 25]
Read/Write Timing
1
2
3
4
5
6
7
8
9
10
t
CYC
t
CLK
t
t
t
CENS CENH
CL
CH
CEN
t
t
CES
CEH
CE
ADV/LD
WE
BWX
A1
A2
A4
CO
A3
A5
A6
A7
ADDRESS
t
t
t
t
DS
DH
t
t
t
DOH
OEV
CLZ
CHZ
t
t
AS
AH
Data
D(A1)
D(A2)
D(A2+1)
Q(A3)
Q(A4)
Q(A4+1)
D(A5)
Q(A6
-Out (DQ)
t
OEHZ
t
DOH
t
OELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
READ
Q(A3)
READ
Q(A4)
BURST
READ
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
D(A2+1)
Q(A4+1)
DON’T CARE
UNDEFINED
Notes:
23. For this waveform ZZ is tied low.
24. When CE is LOW, CE is LOW, CE is HIGH and CE is LOW. When CE is HIGH, CE is HIGH or CE is LOW or CE is HIGH.
1
2
3
1
2
3
25. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved). Burst operations are optional.
Document #: 38-05538 Rev. *G
Page 20 of 28
CY7C1354C
CY7C1356C
Switching Waveforms (continued)
NOP,STALL and DESELECT Cycles[23, 24, 26]
1
2
3
4
5
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWX
A1
A2
A3
A4
A5
ADDRESS
t
CHZ
D(A4)
D(A1)
Q(A2)
Q(A3)
Q(A5)
Data
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
DON’T CARE
UNDEFINED
Note:
26. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
Document #: 38-05538 Rev. *G
Page 21 of 28
CY7C1354C
CY7C1356C
Switching Waveforms (continued)
ZZ Mode Timing[27, 28]
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
27. Device must be deselected when entering ZZ mode. See cycle description table for all possible signal conditions to deselect the device.
28. I/Os are in High-Z when exiting ZZ sleep mode.
Document #: 38-05538 Rev. *G
Page 22 of 28
CY7C1354C
CY7C1356C
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
CY7C1354C-166AXC
CY7C1356C-166AXC
CY7C1354C-166BGC
CY7C1356C-166BGC
Part and Package Type
166
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Commercial
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1354C-166BGXC 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-166BGXC
CY7C1354C-166BZC
CY7C1356C-166BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1354C-166BZXC 51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
CY7C1356C-166BZXC
CY7C1354C-166AXI
CY7C1356C-166AXI
CY7C1354C-166BGI
CY7C1356C-166BGI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1354C-166BGXI 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-166BGXI
CY7C1354C-166BZI
CY7C1356C-166BZI
CY7C1354C-166BZXI
CY7C1356C-166BZXI
CY7C1354C-200AXC
CY7C1356C-200AXC
CY7C1354C-200BGC
CY7C1356C-200BGC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
200
Commercial
CY7C1354C-200BGXC 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-200BGXC
CY7C1354C-200BZC
CY7C1356C-200BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1354C-200BZXC 51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
CY7C1356C-200BZXC
CY7C1354C-200AXI
CY7C1356C-200AXI
CY7C1354C-200BGI
CY7C1356C-200BGI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1354C-200BGXI 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-200BGXI
CY7C1354C-200BZI
CY7C1356C-200BZI
CY7C1354C-200BZXI
CY7C1356C-200BZXI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
Document #: 38-05538 Rev. *G
Page 23 of 28
CY7C1354C
CY7C1356C
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
250
CY7C1354C-250AXC
CY7C1356C-250AXC
CY7C1354C-250BGC
CY7C1356C-250BGC
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Commercial
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1354C-250BGXC 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-250BGXC
CY7C1354C-250BZC
CY7C1356C-250BZC
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
CY7C1354C-250BZXC 51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
CY7C1356C-250BZXC
CY7C1354C-250AXI
CY7C1356C-250AXI
CY7C1354C-250BGI
CY7C1356C-250BGI
51-85050 100-pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm)
CY7C1354C-250BGXI 51-85115 119-ball Ball Grid Array (14 x 22 x 2.4 mm) Lead-Free
CY7C1356C-250BGXI
CY7C1354C-250BZI
CY7C1356C-250BZI
CY7C1354C-250BZXI
CY7C1356C-250BZXI
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm)
51-85180 165-ball Fine-Pitch Ball Grid Array (13 x 15 x 1.4 mm) Lead-Free
Document #: 38-05538 Rev. *G
Page 24 of 28
CY7C1354C
CY7C1356C
Package Diagrams
100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) (51-85050)
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
R 0.08 MIN.
0.20 MAX.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0°-7°
0.60 0.15
0.20 MIN.
51-85050-*B
1.00 REF.
DETAIL
A
Document #: 38-05538 Rev. *G
Page 25 of 28
CY7C1354C
CY7C1356C
Package Diagrams (continued)
119-Ball BGA (14 x 22 x 2.4 mm) (51-85115)
Ø0.05 M C
Ø0.25 M C A B
A1 CORNER
Ø0.75 0.15(119X)
Ø1.00(3X) REF.
1
2
3
4
5
6
7
7
6
5
4
3
2
1
A
B
C
D
E
A
B
C
D
E
F
F
G
H
G
H
J
K
L
J
K
L
M
N
P
R
T
M
N
P
R
T
U
U
1.27
0.70 REF.
A
3.81
12.00
7.62
B
14.00 0.20
0.15(4X)
30° TYP.
51-85115-*B
SEATING PLANE
C
Document #: 38-05538 Rev. *G
Page 26 of 28
CY7C1354C
CY7C1356C
Package Diagrams (continued)
165-Ball FBGA (13 x 15 x 1.4 mm) (51-85180)
BOTTOM VIEW
PIN 1 CORNER
TOP VIEW
Ø0.05 M C
PIN 1 CORNER
Ø0.25 M C A B
-0.06
Ø0.50
(165X)
+0.14
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
A
B
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
A
1.00
5.00
10.00
13.00 0.10
B
B
13.00 0.10
0.15(4X)
NOTES :
SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)
PACKAGE WEIGHT : 0.475g
JEDECREFERENCE: MO-216 / DESIGN 4.6C
PACKAGE CODE : BB0AC
SEATING PLANE
C
51-85180-*A
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device
Technology, Inc. All product and company names mentioned in this document are the trademarks of their respective holders
Document #: 38-05538 Rev. *G
Page 27 of 28
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
CY7C1354C
CY7C1356C
Document History Page
Document Title: CY7C1354C/CY7C1356C 9-Mbit (256K x 36/512K x 18) Pipelined SRAM with NoBL™ Architecture
Document Number: 38-05538
Orig. of
REV.
**
ECN No. Issue Date Change
Description of Change
242032
278130
See ECN
See ECN
RKF
RKF
New data sheet
*A
Changed Boundary Scan order to match the B Rev of these devices
Changed TQFP pkg to Lead-free TQFP in Ordering Information section
Added comment of Lead-free BG and BZ packages availability
*B
*C
284431
320834
See ECN
See ECN
VBL
PCI
Changed ISB1 and ISB3 from DC Characteristic table as follows
ISB1: 225 mA-> 130 mA, 200 MHz -> 120 mA, 167 MHz -> 110 mA
ISB3: 225 MHz -> 120 mA, 200 MHz -> 110 mA, 167 MHz -> 100 mA
Add BG and BZ pkg lead-free part numbers to ordering info section
Changed 225 MHz to 250 MHz
Address expansion pins/balls in the pinouts for all packages are modified as
per JEDEC standard
Unshaded frequencies of 250, 200, 166 MHz in AC/DC Tables and Selection
Guide
Changed Θ and Θ for TQFP Package from 25 and 9 °C/W to 29.41 and
JA
JC
6.13 °C/W respectively
Changed Θ and Θ for BGA Package from 25 and 6 °C/W to 34.1 and
JA
JC
14.0 °C/W respectively
Changed Θ and Θ for FBGA Package from 27 and 6 °C/W to 16.8 and
JA
JC
3.0 °C/W respectively
Modified V test conditions
V
OL, OH
Added Lead-Free product information
Updated Ordering Information Table
Changed from Preliminary to Final
*D
351895
See ECN
PCI
Changed I
Updated Ordering Information Table
from 35 to 40 mA
SB2
*E
*F
377095
408298
See ECN
See ECN
PCI
Modified test condition in note# 15 from V
< V to V
≤ V
DDQ
DD
DDQ DD
RXU
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed three-state to tri-state.
Modified “Input Load” to “Input Leakage Current except ZZ and MODE” in
the Electrical Characteristics Table.
Replaced Package Name column with Package Diagram in the Ordering
Information table.
*G
501793
See ECN
VKN
Added the Maximum Rating for Supply Voltage on V
Relative to GND
DDQ
Changed t , t from 25 ns to 20 ns and t
from 5 ns to 10 ns in TAP
TH TL
TDOV
AC Switching Characteristics table.
Updated the Ordering Information table.
Document #: 38-05538 Rev. *G
Page 28 of 28
|