XAP™ 800 Audio Conferencing
System
Installation & Operation Manual
iii
XAP 800 Installation and Operation Manual
Table of Contents
CHAPTER 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . .1
Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Product registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Product returns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Professional Services Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Controls and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Expansion bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operational Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Equipment placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
G-Ware requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
CHAPTER 2: Installation . . . . . . . . . . . . . . . . . . . . . . . . . .9
Hardware Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
To connect the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Networking Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Expansion bus connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Device IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Mixer mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
LCD Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
LCD menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
System menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
RS-232 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Meter menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Inputs menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Outputs menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
iv
CHAPTER 3: System Configuration . . . . . . . . . . . . . . . . . . .21
G-Ware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Creating Floppy Disk Copies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Installing G-Ware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
To install G-Ware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Site Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Creating a new site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Adding a XAP 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Configuring Unit Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
G-Ware Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Flow Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Matrix Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Audio Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Expansion bus O–Z routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Process A–H routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Cross point attenuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Matrix report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Inputs 1–8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Inputs 9–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Outputs 1–12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Expansion Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
From Expansion Bus O–Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
To Expansion Bus O–Z . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Processing A–H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
CHAPTER 4: Advanced Configuration . . . . . . . . . . . . . . . . .55
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Creating Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Running presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Running multiple presets simultaneously . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Creating macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Editing macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Running macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
v
CHAPTER 5: Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Signal Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Document Compare Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Print Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
GFirm Firmware Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
G-Ware Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Copy and paste settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Message Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Monitoring Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Gate View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Meter Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
CHAPTER 6: Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
GPIO Builder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Control/Status A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Remote Builder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
XAP IR Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
ClearOne Control Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
RS-232 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Remote modem access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Serial commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Command Strings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
APPENDICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Appendix B: Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Appendix C: Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Appendix D: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Appendix E: Serial Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Appendix F: Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Appendix G: Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
vi
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 1: Introduction
Product overview
Congratulations on purchasing the XAP 800, a highly advanced twelve-by-twelve
digital matrix mixer with Gentner® Distributed Echo Cancellation®, noise
cancellation, and audio processing. It uses an internal macro language and 32 user-
definable presets to quickly adapt to a variety of teleconferencing and sound
reinforcement applications such as distance learning, teletraining, telemedicine,
courtrooms, conference rooms, boardrooms, hotels, and houses of worship.
In its most simple form, the XAP 800 is a mic mixing matrix. As such, all mic
mixing parameters can be customized and any input or combination of inputs can
be routed to any output or combination of outputs, with attenuation adjustments at
each cross point.This allows great flexibility in accommodating a variety of
applications and requirements.
The XAP 800 features numerous functions which greatly enhance its
performance and flexibility. For example, it can gate mics on and off when the
sound within a mic’s acceptance pattern reaches a certain level.
The XAP 800 monitors each mic independently, observing ambient levels and
making decisions based on each mic’s environment.Thus, the input for a mic
located in a highly reverberant part of a conference room is gated, mixed, and
processed to compensate for the changes in that area and reduce echo and noise.
This improves audio quality and decreases the possibility of feedback.
The XAP 800 facilitates local and remote PC setup and diagnostics, logic
outputs, and automatic gated mic operation. Mic inputs can be individually
customized to gate on and off as you want, while automatic gain control keeps the
overall sound level consistent. Eight of the 12 channels can be configured as an
automatic microphone mixer.
Adjustments in routing, level, and other functions can be made through presets
activated through a closure on the rear panel, an RS-232 serial interface, or a
control panel on the expansion bus data channel.
The XAP 800 features eight audio processing blocks, each with 15 filters.
Each filter can be configured as a parametric equalizer, high pass, low pass, CD
horn, high shelving, low shelving, all pass, or crossover.This allows you to tailor the
XAP 800’s audio response to optimize the audio quality and fidelity characteristics
of a wide variety of sound reinforcement systems.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ New Features
2
The GPIO (general purpose input/output) allows switching among any of 32
user-stored presets.This gives you real-time flexibility to meet a variety of
reinforcement requirements.
Network-based interconnectivity allows up to eight XAP 800s and XAP 400s
to be connected and controlled as a single unit, allowing microphone coverage in
applications requiring up to 64 mics.
The XAP 800’s Macro Pro™ scripting language allows the unit to function
without the need for an external controller. However, it can be easily interfaced to
an external controller via either of the two RS-485 ports.The unit can also
interface with a PC through the RS-232 port.
New Features
•
Virtual references. The XAP 800 now supports echo cancellation summing.
Four user-definable virtual references are provided which can use multiple
signals as the echo cancellation reference point without sacrificing an analog
output.This added flexibility further enhances echo cancellation performance.
•
•
•
Improved noise cancellation. Our industry-leading noise cancellation keeps
background noise to a minimum while retaining top-level voice quality, echo
cancellation performance, and full-duplex capability.
Front panel gain and mute control. Now gain and mute adjustments can
be made from the front panel. Using these controls allows you to make quick
volume and mute changes without connecting through G-Ware.
Safety Mute. The new Safety Mute button on the main G-Ware toolbar
allows you to mute all outputs with one simple click if feedback or audio
problems occur during the configuration process.
•
•
•
Preset and Macro Passwords. You can now password protect your presets
and macros to prevent unauthorized changes.
Clear Matrix. This new button on the Matrix Screen makes it easy to clear all
cross point cells in the matrix. Simply click the button and confirm the action.
RAMP serial command. The new RAMP serial command (see page 123)
gives you greater control over gain adjustments.You can specify the rate at
which the gain increases and decreases as well as the target level.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Professional Services Group
3
Professional Services Group
If you need any additional information on how to install, set up, or operate your
system, please contact us at one of the locations listed below.We welcome and
encourage your comments so we can continue to improve our products and serve your
needs.
ClearOne Communications ~ 1825 Research Way ~ Salt Lake City, Utah 84119
Technical Support
Telephone:
Fax:
1.800.283.5936(USA) or 1.801.974.3760
1.801.977.0087
E-mail:
Web site:
tech.support@clearone.com
www.clearone.com
Sales and Customer Service
Telephone:
Fax:
1.800.945.7730 (USA) or 1.801.975.7200
1.800.933.5107 (USA) or 1.801.977.0087
sales@clearone.com
E-mail:
ClearOne Communications EuMEA GmbH
Leonhardstr. 16-18, D-90443 Nuremberg, Germany
Telephone:
Fax:
+49 911 955159-0
+49 911 955159-10
global@clearone.com
E-mail:
Product registration
Please register your XAP 800 online by visiting ClearOne Technical Support at
www.clearone.com. When your product is properly registered, ClearOne
Communications is better able to serve you should you require technical assistance.
Registration information is also used to notify you of upgrades and new product
information.
Product returns
All product returns require a return authorization (RA) number. Please contact
ClearOne Technical Support before attempting to return your XAP 800 unit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Unpacking
4
Unpacking
Ensure that the following items were received with your shipment:
ClearOne
is
not
responsible for product
damage incurred during
!
shipment. You must make claims
directly with the carrier. Inspect
your shipment carefully for obvious
signs of damage. If the shipment
appears to be damaged, retain the
original boxes and packing material
for inspection by the carrier.
Contact your carrier immediately.
Figure 1.1. Equipment included with XAP 800 unit
Controls and Connections
Front panel
Figure 1.2. Front panel controls
A. LCD. This display is for XAP 800 setup in conjunction with the four
associated front-panel buttons [B, C, and D]. Baud rate and flow control
must be configured from the front panel; see the LCD Menu Tree on page 13
for the location of these in the menu system. Other functions accessed via the
front panel include system options, RS-232 configuration, troubleshooting,
and level readings.
All front panel buttons are
also used to enter the
✍
front panel passcode. See
Security (page 26) for more
details.
B. Enter. This button is used when programming the XAP 800 via the LCD
window.To move deeper in the menu or execute a selected parameter, press
the Enter button.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Controls and Connections
5
C. ▲/▼ These buttons scroll up and down through vertical programming
options within a specific XAP 800 programming parameter or
increases/decreases a numeric value.
D. Esc. This button steps you out of a selected parameter or moves you up one
level in the menu. When a parameter has been displayed with the arrow
buttons [C], you can select it with the Enter button [B] to modify it.Then,
you can step out of the menu with the Esc button.
E. LED meter. This assignable, peak-level LED bar meter is used to display the
audio level of an input, output, or processing channel of the XAP 800.
F. Meter. Takes you directly to the Meter branch of the XAP 800’s LCD menu
tree.
G. LED 1–8. These LEDs indicate Inputs 1–8 gate status.
Rear panel
Figure 1.3. Rear panel connections
A. Power. This power module accommodates power ranging from
100–240VAC, 50/60Hz.The module uses an IEC-type connector. No
switching is required.
B. Inputs 1–8. These Phoenix block connectors are for connection of eight
mic-level or line-level (selectable) inputs.These connectors are typically used
for mics, but can be configured for use with VCRs, CD players, XAP TH2,
etc.These inputs can be mixed in any gated or non-gated combination and
routed to any of the 12 outputs. Default input level is -55dBu. For more
information about input adjustments, see page 32. For electrical
specifications, see Appendix A: Specifications.
C. RS-485 Remote Panel A/B Port. These four-pin Phoenix connector ports
allow you to control the XAP 800 with the ClearOne Control Panel or XAP
IR Remote Control.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Controls and Connections
6
Power is supplied through the RS-485 ports to the remote Control Panels
from the XAP 800.This power is limited to a total of 300mA at 15 volts for
each connector. Over-current protection is provided on the +15V pins to
prevent damage in the event of shorting. External power can be provided to
control devices when more current is required. See page 92 for maximum
cable run distances when using ClearOne Control Panels.
D. Control/Status Ports A and B.These two female DB25 connector are used
to connect control devices to the XAP 800.The control devices have access
to the command set for the XAP 800 and can be used for common functions
such as volume control, muting, preset change, room combining, etc. Devices
can be connected to either port.
For instructions on how to program the control and status pins, see the
GPIO section on page 77.The default settings allow control and status of
inputs, outputs, volume, and presets.These pins are active low.The 32 presets
can also be activated via these connectors. For pinout and default
information, see Appendix B.
E. Outputs 1–12. These three-pin Phoenix connectors are for connection of
twelve line-level balanced outputs with three-pin Phoenix connectors.These
outputs are typically used for connection to VCRs, tape recorders, amplifiers,
codecs, phone hybrids, and other audio devices.These outputs may be
configured to contain any combination of gated and non-gated inputs.The
nominal output level is 0dBm.
F. Inputs 9–12. These Phoenix connectors are for connection of up to four
line-level inputs.These are typically used for connection of VCRs, tape
players, CD players, and other audio sources.They can be routed to any
output or multiple outputs. Nominal level is 0dBu.
G. Expansion Bus In/Out. This RJ-45 connector is part of the expansion bus
(E-bus), which allows up to eight XAP 800 or XAP 400 units and up to 16
XAP TH2 units to be networked together.The E-bus consists of two buses:
one for control, the other for passing audio and mic information (see Control
bus, page 7). Using Cat 5 twisted-pair cable, you can separate adjoining units
up to 80 feet (24 meters). See the diagram on page 11.
I. RS-232. This female DB9 serial port is for interconnection between the XAP
800 and a PC, modem, or other custom remote controller. For serial
protocol, see Appendix B: Connector Pinouts.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Networking
7
Networking
Expansion bus
The latency or propagation
delay is <1ms.
✍
The digital mix-minus expansion bus (RJ-45 LAN) is used to connect up to eight
XAP 800/400s and 16 XAP TH2 units, where the total number of microphone inputs
does not exceed 64.The maximum distance between interconnected XAP 800/400 or
PSR1212 units is 80 feet (24 meters). Connecting a XAP TH2 must not increase the
cable length between two PSR1212s, XAP 800s and/or XAP 400s beyond 80 feet.
ClearOne recommends that category five twisted-pair (10BaseT LAN) cable be used.
The expansion bus (E-bus) allows audio routing between destinations on the
E-bus network.The E-bus contains 12 independent digital audio buses labeled O–Z
which can route mic or line level inputs in any combination across the E-bus
network.The O–Z buses are divided into two groups (O–R and S–Z) based on their
capabilities and default settings.The E-bus also contains four PA adapt/acoustic
echo cancellation reference buses, four global gating buses, and one control bus.
•
O–R buses. These four audio buses are defaulted as the mic mix buses; they
can communicate the NOM count and mic mixing parameters across the
network to other XAP 800s. All gated mics are routed to the 0 bus by default.
•
S–Z buses. These eight buses are defaulted as auxiliary mix buses.They are
used to route auxiliary audio, such as from a CD player or VCR, to and from
other units on the network.These buses are also used as mic mix buses when
NOM count is not required.
•
•
PA Adapt/Acoustic Echo Cancellation Reference buses. These buses
allow an input from a XAP 800 to reference an output on another linked
XAP 400/800. See PA Adapt and AEC Reference on page 33 for more
information.
Global Gating Groups A–D buses. These mix-minus buses are defined as
microphone gating groups which support first-mic priority, maximum number
of mics, etc. and work across all linked XAP 400/800s. Unlike the audio
buses, they contain only mic status and gate parameters. See page 41 for
more information about gating groups.
•
Control bus. The control bus is an independent channel from the E-bus’s
audio channel; it uses a different pair of wires on the same E-bus cable.This
allows control information to pass even if the units are not using the audio
link.The XAP 800 supports the full set of commands through the control bus.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Introduction ~ Operational Requirements
8
Operational Requirements
Power
The XAP 800 automatically accommodates voltage requirements of 100–240VAC,
50/60Hz, 15W.
Equipment placement
The XAP 800 units are designed for installation in a standard 19-inch equipment
rack.You can also purchase side panels for desktop placement. See Appendix D for a
list of accessories.
Environmental
The XAP 800 can be safely operated in a room with varying temperatures between
32 °F/0 °C and 110 °F/43 °C.
G-Ware requirements
ClearOne’s G-Ware software requires the following minimum system configuration:
•
Minimum RAM requirement is determined by the operating system
Windows 95 OSR2
Windows 98
64MB
64MB
64MB
64MB
128MB
256MB
Windows ME
Windows NT
Windows 2000
Windows XP
•
•
•
•
•
•
•
PII 200MHz (or AMD equal) or higher processor
8MB Video Card
1024x768 (16 bit) High Color monitor
Internet Explorer 4
20MB of free hard disk space
RS-232 COM port
CD-ROM drive
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 2: Installation
The XAP 800 is designed for easy installation and setup. All connections are made
through rear-panel connectors.This chapter provides instructions on making
hardware connections, creating an expansion bus (E-bus) network, assigning device
ID numbers, selecting the mixer mode, and using the front panel LCD menu.
Hardware Setup
The diagram below illustrates the typical connections that are made for a single-unit
XAP 800 system.The default routing settings in the G-Ware Matrix Screen allow the
XAP 800 to work out of the box for this type of installation.
Figure 2.1. XAP 800 installation diagram
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ Hardware Setup
10
Figure 2.2. XAP 800 rear-panel connectors
To connect the unit
1. Place the unit in a standard 19-inch rack and attach it securely.
2. If you are using a custom controller for control and status, plug it into the
DB25 Control/Status A or B port [D].
If you are using an external RS-232 controller, connect it to the
RS-232 port [I].
3. Wire the inputs and outputs to the XAP 800 using the provided three-
terminal Phoenix push-on connectors.These connectors are designed for easy
wiring; simply insert the desired wire into the appropriate connector opening
and tighten down the top screw.
The three terminals in
the Phoenix connector
correspond with the rear-
panel audio contacts (from left to
right): + (positive), – (negative),
and ꢀ (ground).
✍
•
•
•
Inputs 1–8 [B] Mic or line level inputs
Inputs 9–12 [F] Line level inputs only
Outputs 1–12 [E] Line level outputs
4. If you are using a ClearOne Remote Panel, wire it to the RS-485 port [C]
using the provided four-terminal Phoenix push-on connectors.
5. Plug in the XAP 800 to complete the installation.The power output [A] will
operate at any level between 100–240VAC and 50–60Hz.
If you are installing only one XAP 800 and are not connecting it to any other XAP
or PSR1212 units, you have completed the hardware installation.
Figure 2.3. Phoenix push-on connector
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ Networking Units
11
Networking Units
Expansion bus connections
Using the Expansion Bus ports (RJ-45), you can connect up to eight XAP 800/400s
and 16 XAP TH2 units, where the total number of microphone inputs does not
exceed 64. Make connections between units in daisy-chain fashion using the short
RJ-45 jumper. If your units are further apart, use category five twisted-pair cable.
The maximum distance between interconnected XAP 800/400 or PSR1212
units is 80 feet (24 meters). Expansion bus cable length is calculated between
XAP 800s/400s and PSR1212s.The cable connecting a XAP TH2 to the network
is included in the cable length between the XAP 800 or XAP 400. For example, if
the cable from the XAP 800 to the XAP TH2 is 50 feet and the cable from the
XAP TH2 to the second XAP 800 is 50 feet, then the total length between the two
XAP 800s is 100 feet which is beyond the maximum 80-foot limit.
Figure 2.4. E-bus connection diagram
To create an expansion bus network
1. Plug the expansion bus terminator in the Expansion Bus In connector of
ClearOne
recommends
the first unit in the network.
that the first unit in your E-
bus network be a XAP 400
or XAP 800 rather than a XAPTH2.
✍
2. Connect the RJ-45 jumper cable (or Cat 5 twisted pair cable) to the
Expansion Bus Out connector of the first unit in the network and
Expansion Bus In connector of the second unit. Continue connecting units
in the same fashion.
3. Plug the expansion bus terminator in the Expansion Bus Out connector on
RS-232 system-wide con-
the final unit to complete the network connections.
trol can be provided by
✍
any unit in the network.
If the E-bus network is not connected properly, the front panel LEDs will
flash on the units that are physically connected to the network.To correct
the problem, check for broken connections and reconnect the expansion bus
cables.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ Networking Units
12
If the same device ID is
assigned to more than one
unit on the E-bus network,
Device IDs
✍
Once your expansion bus connections are made (and if you have more than one
XAP 800 at a site), you need to set up a unique expansion bus device ID number—a
network address—for each XAP 800 on the network. As shipped from the factory, all
XAP 800s are set to device ID 0.
the Meter LED “+12” will flash
red, the Mic LEDs “1,” “2,” “4,”
and “8” will flash green on the
affected units. To correct the
problem, change the device ID on
one of the conflicting units.
To assign device IDs
1. Press the front-panel Enter button, then scroll through the menu until the
System menu is visible.
2. Press Enter, then scroll through the menu until Device ID is visible.
3. Press Enter, then scroll through the eight (0–7) options. When the desired
device ID is visible, press Enter to select it. (You can also set the device ID in
the Unit Properties window of G-Ware software see page 25.)
4. Repeat this process for each XAP 800 on the expansion bus network.
You can also use G-Ware
to select a mixer mode.
See page 25.
Mixer mode
✍
There are two mixer mode settings: slave (default) and master. A master unit is not
required in a networked system and in most installations, all units will be slaves.
Master units ignore audio from upstream units.This prevents audio from being
received from units above the master unit in the network. However, global control of
the system is still maintained by whichever XAP 400/800 or PSR1212 unit is
connected to a control device through its RS-232 or RS-485 ports. Control is not
affected by master/slave designations.
In Figure 2.5, the third unit in the network is a master. It prevents the audio
from the first and second units from being passed down the network chain.
Likewise the second master unit in the network will not pass on the audio from the
unit before it.The third unit provides system-wide control through a connection to
its RS-232 port.
To select a mixer mode
1. Press the front panel Enter button and scroll through the menu until System
menu is visible. Press Enter to select the menu.
2. Scroll through the System menu and select Mixer Mode.
3. Select the mixer setting you want to use.
Repeat for additional units.
Figure 2.5. E-bus network with master units
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
13
LCD Programming
The XAP 800’s front panel is intuitive to operate, thanks to its simple interface: a
2x16 character LCD, menu buttons, and a peak-level LED bar meter. Although most
of the XAP 800’s features are programmed with G-Ware software (see page 23), the
front panel can be used for simple adjustments and meter monitoring.
G-Ware
software
is
required to complete
✍
system setup.
When power is applied to the XAP 800, the LCD panel will first read
INITIALIZING. If an error is displayed, contact technical support. When
initialization is complete, “XAP 800” is displayed on the top line and “Unit 0” is
displayed on the bottom line.
LCD menu tree
Pressing Esc at the top of
the tree does nothing.
The menu tree features five main menus, each with submenus.These branches
typically end when an adjustable parameter or viewable value is reached.The
diagram below shows the LCD menu tree.
✍
Figure 2.6. LCD menu tree
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
14
The five main menus are: System, RS-232, Meter, Inputs, and Outputs. All
submenu items are arranged under these menus. Use the Enter button to select items
and the ▲ and ▼ buttons to scroll through menus and submenus.When the last
menu item is reached, the display scrolls back to the beginning of the list.The Esc
button allows you to back out of the menus.
To adjust a parameter
1. Scroll to the parameter you want to adjust. Press Enter to select the
parameter.The parameter will flash when selected.
2. Adjust the value with the ▲ and ▼ buttons. As the value is adjusted, the
parameter is updated immediately.
3. To store the new value, press Enter.To discard the change and revert back
to the old value, press Esc.
If the Meter button is pressed while a parameter is being adjusted, the LCD
will switch to the Meter menu.
System menu
There are eight system-level parameters (see Figure 2.6): Select Preset, Run Macro,
Lock Panel, Set Passcode, Device ID, Mixer Mode, Unit ID, and Firmware Version.
Select Preset
The Select Preset menu item allows for one of 32 preprogrammed presets to be
selected for XAP 800 use.To select a preset, scroll through the numbered presets
(1–32) until the desired preset is visible, then press Enter to run the preset.
Run Macro
The Run Macro menu item allows you to execute a macro.To select a macro, scroll
through the numbered macros (1–255) until the desired macro is visible, then press
Enter to run the macro.
Lock Panel
The front panel may be locked to prevent unauthorized adjustments to the XAP 800.
To lock the front panel, use the ▲/▼ buttons to select Lock Panel from the System
menu, and press Enter. Lock Panel selections are Off, On, or On at Timeout. Press
Enter to enable your selection.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
15
To unlock the front panel, attempt to adjust a parameter.The XAP 800 will
prompt for the passcode. Upon entering the fifth character (if entered correctly),
the front panel will unlock.The default passcode for all boxes is ▲▲▼▼Enter.
Menu items can still be
scrolled through when the
panel is locked. However,
settings cannot be entered until the
panel is unlocked with the
appropriate passcode.
✍
Set Passcode
Once the XAP 800 is unlocked, the passcode may be changed. Before the XAP 800
will allow passcode changes, the new passcode must be entered, then re-entered to
validate the new passcode.
The front panel passcode can also be set (and reset) within G-Ware. See page
26 for more information.
Device ID
The XAP 800’s device ID is set from this menu.There are eight device ID selections
to choose from (0–7). Select the network position you want to use.Within a single
site, you must assign different device ID numbers for each XAP 800 unit. See Device
IDs, page 12.
Unit ID
The Unit ID menu selection allows you to access the read-only address set at the
factory.This unique ID number identifies your particular XAP 800 unit and cannot be
changed.
Mixer Mode
This setting allows you to set to master or slave mode. See page 12 for details.
Firmware Version
This menu selection allows you to view which firmware version is being used.This
information cannot be changed.
RS-232 menu
There are four submenus under the RS-232 menu: Baud Rate, Flow Control, Enable
Modem, and Clear Password.
Baud Rate
This parameter allows you to set the XAP 800’s baud rate to 9.6kbps, 19.2kbps,
38.4kbps, or 57.6kbps. Default is 38.4kbps. Select the baud rate you want to use,
then press Enter.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
16
ClearOne
recommends
Flow Control (hardware)
that you leave Flow
Control enabled.
✍
The XAP 800 uses the RTS and CTS pins on the RS-232 port to regulate the
transmission and reception of data.You can enable or disable flow control on the
front panel of unit and select the flow control type in the Site Properties window of
G-Ware (see page 23). If you select On (default) from the front panel menu, select
Hardware as the flow control type in the Site Properties window. If you disable flow
control on the front panel, select None in the Site Properties window.When None is
selected, the XAP 800 ignores flow control, making the connected external control
device ensure that data is not lost. Software flow control (Xon/Xoff) is supported by
the XAP/PSR units and is only used with a pass-through device, such as a modem.
To avoid communication errors, ClearOne strongly recommends that you
connect all DB9 pins and enable flow control when connecting to a PC.
Enable Modem
The modem initialization
string can only be set via
This parameter configures the RS-232 port for connection of a modem.When On is
selected, the XAP 800 will send an initialization string to the modem on power-up
and require a password before data transfer is allowed through the port.When Off
(default) is selected, the password is disabled.
✍
the
MINIT
serial
command (see page 116 or the
G-Ware software. It cannot be set
through the front panel LCD.
To use the XAP 800 with a modem
1. Match the baud rate of the modem to that of the XAP 800.
2. Turn off Serial Echo on the modem.
3. Turn off the modem’s response mode (e.g., no OK messages, ring, etc.).
4. Enable auto-answer on the modem.
You can set the modem
password
using
the
Clear Password
✍
MPASS serial command
(see page 117) or in G-Ware (see
page 26).
This parameter allows you to erase the serial port (modem) password in case it has
been forgotten. Select Yes to keep the current password or No to erase it. Press
Enter to enable your selection.
Meter menu
There are six submenus under the Meter menu: Inputs, Outputs, Processing, ERL,
ERLE, and Default Meter.The meter selection determines what is shown on the front
panel peak-level LED display.When the meter is selected in the LCD menu tree, the
LCD displays peak level indications as well. Use the ▲ and ▼ buttons to select the
Meter menu, then scroll through the options and press Enter when you reach the
desired option.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
Inputs
17
Select which input (1–12) you want to monitor on the LCD and LED display. Scroll
to the input, then press Enter.The meter displayed is the post-gain meter.
Outputs
This submenu allows you to choose which output (1–12) you want to monitor on the
LCD and LED display. Scroll to the output you want to monitor, then press Enter.
Processing
This submenu allows you to choose which processing channel (A–H) you want to
monitor on the LCD and LED display. Scroll to the output you want to monitor, then
press Enter.
ERL
This submenu allows monitoring of the ERL meters on the XAP 800. Select the
meter you want to monitor and press Enter.
ERLE
This submenu allows monitoring of the ERLE meters on the XAP 800. Select the
meter you want to monitor and press Enter.
Default Meter
This submenu determines what is displayed on the LED meter when a meter is not
specifically selected elsewhere in the Meter menu.The default is Output 12.
The Meter Reference Point diagram on page 19 shows the meter pick-up
M
points ( ) in the XAP 800 signal path.
Inputs menu
There are two submenus under the Inputs menu: Mute and Gain.To access these
submenus you must first select the input. Choose from Inputs 1–12 or Global. Use
the ▲ and ▼ buttons to select the Inputs menu, then scroll through the options and
press Enter when you reach the desired option.
Mute
This submenu allows you to turn mute on or off (default) for the selected input.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
18
Gain
This submenu allows you to adjust the gain for the selected input. Use the ▲ and ▼
buttons to increase or decrease gain.
Outputs menu
There are two submenus under the Outputs menu: Mute and Gain.To access these
submenus you must first select the output. Choose from Outputs 1–12. Use the ▲
and ▼ buttons to select the Outputs menu, then scroll through the options and press
Enter when you reach the desired option.
Mute
This submenu allows you to turn mute on or off (default) for the selected output.
Gain
This submenu allows you to adjust the gain for the selected output. Use the ▲ and ▼
buttons to increase or decrease gain.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Installation ~ LCD Programming
19
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
20
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 3: System
Configuration
ClearOne’s G-Ware software provides an easy interface for configuring and controlling
your XAP 800.While some configuration can be done using the front panel LCD
menus, G-Ware is required to complete the custom configuration of your audio
conferencing system. If you are using the default settings, no configuration is
necessary.
This chapter describes how to install G-Ware and create a site. It also
describes all configurable parameters of your system.These descriptions are
designed to be used as a guide as you make adjustments for your particular
installation. It is not necessary to configure all parameters.
G-Ware Requirements
ClearOne’s G-Ware software requires the following minimum system configuration:
•
Minimum RAM requirement is determined by the operating system
Windows 95 OSR2
Windows 98
64MB
64MB
64MB
64MB
128MB
256MB
Windows ME
Windows NT
Windows 2000
Windows XP
•
•
•
•
•
•
•
PII 200MHz (or AMD Equal) or higher processor
8MB Video Card
1024x768 (16 bit) High Color monitor
Internet Explorer 4
20MB of free hard disk space
RS-232 COM port
CD-ROM drive
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Installing G-Ware
22
Creating Floppy Disk Copies
Depending upon the computer equipment you have available, you might need to install
G-Ware software from floppy disks rather than the included CD.To do this, a Disk
Copy program is provided in G-Ware that allows you to transfer G-Ware to floppy
disks.You will need a PC with a CD-ROM drive to make the transfer.You can access
the Disk Copy program in the following ways:
•
After installing G-Ware, go to the Windows® Start menu, select Programs,
then ClearOne G-Ware, then Create Install Floppy Disks.
– or –
•
In the G-Ware section of the Audio Video Product CD, click on Install Now.
Choose Create Installation Floppy Disks from the G-Ware setup menu.
Installing G-Ware
To install G-Ware
1. Boot the PC to the Windows operating system. Ensure that all other
programs or applications are closed. Insert the Audio and Video Products CD
into the CD-ROM drive.
If the Autorun feature is enabled on the PC, the ClearOne Welcome window
opens. Click the Software tab and select G-Ware.
If the Autorun window does not open, open the Windows Start menu and
choose Run.Type “<drive>:\\clearone.exe” where <drive> is the letter of
the CD-ROM drive (e.g., D:\\clearone.exe).
To select an alternate
destination directory, click
Browse and use the
2. At the G-Ware window, click Install G-Ware near the bottom of the window.
✍
3. The InstallShield Wizard opens, and guides you through the Welcome and
License Agreement windows. At the Choose Destination Location window,
choose the directory where G-Ware will be installed. We recommend that
you use the default directory.
Choose Directory window to find
the desired location. Click OK to
return to the previous window.
4. Click Next or Yes to move to proceed through the windows that follow or
No or Cancel to end the installation process.
5. Follow the onscreen instructions.You must restart your computer once
installation is complete.
The G-Ware Program Folder is now added to your Start menu.You can start
G-Ware through the Start menu or by double-clicking the desktop icon.
Figure 3.1. Desktop icon
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Site Setup
23
Site Setup
Whenever a mouse click is
indicated in this manual, it
refers to the left mouse
Creating a new site
✍
New site files are created through the Site Properties window in G-Ware. A site file
contains all information about a particular installation including all unit settings and
properties. It also provides G-Ware with the necessary information to communicate
with the site hardware using your PC. Open G-Ware by double clicking the desktop
icon or by selecting G-Ware from the Start menu.
button unless otherwise stated.
To create a new site
1. Open the Site Properties window by selecting New Site from the File menu
Figure 3.2.
New Site button
or by clicking the New Site button on the toolbar.
2. In the Site tab, enter the site name, author, company, location, room, and
description, using the Tab key or mouse to select each field.
You can enable flow
3. Click the Comm tab. Select the COM port, baud rate, and flow control you
want to use. ClearOne recommends that you leave Flow Control set to
Hardware.The Software setting is not supported by XAP/PSR units and is
typically used with modems.
control using the XAP
✍
front panel controls. See
page 16.
4. If you plan to use a modem, select Use Modem and enter the phone number,
initialization string, and reset string.
5. Click the Security tab. Enter the site password in the Site Password box.
Click File Access Password to create a password for the Site File.
Figure 3.5. Site Properties, Security tab
Figure 3.4. Site Properties, Comm tab
Figure 3.3. Site Properties, Site tab
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Site Setup
24
Adding a XAP 800
You can add a XAP 800(s) to your site file by connecting to your site and using
G-Ware to automatically create icons for the detected units. Or, you can work offline
and manually add the unit(s) to the site file and connect to the site at a later time.To
open an existing site file, click the Open Site File button or select Open Site from the
File menu.
Figure 3.6. Open
Site File button
To auto-detect units
1. Click the Connect button on the G-Ware toolbar or select Connect from
the Connect Menu.
Figure 3.7.
Connect
2. Choose Sync to Unit(s). G-Ware will automatically create icons for the new
units it detects on the network and place them in the Site pane. See Figure
3.11.
Figure 3.8. Connection choices
Note: When connecting to your site, you can choose to sync to Unit(s) or
Document. If you sync to the Unit(s), you will overwrite your G-Ware site file
with the current settings of the unit(s). If you sync to the Document, you will
overwrite the settings in your units with the settings you have saved in the site
file. Choosing to sync to Document will also create icons for any new units.
To manually add units
1. If you are working offline, click the Add button on the G-Ware toolbar.This
opens the Add Unit window.
Figure 3.9. Add Unit
to Current Site
Figure 3.10. Add Unit window
2. Select the XAP 800 icon and click Add.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Site Setup
25
Configuring Unit Properties
Using the Unit Properties window, you can configure the unit‘s communication and
security properties in addition to general unit properties such as name, type, and
country code.The Unit Properties window automatically opens when you manually
add a unit to the site.You can also right-click the unit icon in the site pane and click
Unit Properties.
Figure 3.11. Unit icons in Site
Pane with Unit menu displayed
To configure Unit Properties
1. Type a descriptive Unit Name in the space provided.The Unit Identification
and Firmware Version will be supplied by the unit when a connection is made.
2. If you have already established a connection with the site, the Device
ID will be assigned. Otherwise, select the Device ID that matches the ID you
assigned the unit via the front-panel LCD menu.
Device IDs ensure the software will sync up with the proper unit when there
are multiple XAP 800s on a network.
3. Select the Unit Type (default is slave). See page 12 for more information.
4. Select an input, output, or processing channel to be the Default Meter on
the front panel meter LED when a channel is not specifically selected.
Figure 3.12. Unit Properties, General tab
5. Select the Meter Refresh Rate, which determines how quickly the XAP 800
updates meter information (default is 100ms; range is 50–1000ms).
6. Click the Comm tab.The Baud Rate and Flow Control settings are supplied
by the unit when a connection is made.These settings are changed using the
Site Properties window (see page 23).
7. Set the Serial Echo (default On) and the Serial Mode (default Text).
Serial Echo echos back commands sent over the XAP 800 network.The serial
mode determines the format in which the commands return—text or binary.
The mode defaults to Binary when G-Ware is connected and to Text when
disconnected. Contact technical support for instructions on using Binary
mode.
Figure 3.13. Unit Properties Comm tab
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Site Setup
26
8. If a modem is connected to the XAP 800 unit, select Use Modem and enter
the initialization string. Click OK; the XAP 800 will initialize the modem.
9. Click the Security tab. Create a modem password.The password will be
required before control of the system is allowed.The default modem
password is a carriage return.
10. Preset/Macro Password enables you to password protect your individual
presets and macros.To create a password, click Preset/Macro Password.
Creating a Preset/Macro Password does not automatically lock all presets
or macros. Presets are locked in the Preset Configuration Mode. See page
56 for more information. Macros are locked in the Macro Editor. Presets
and Macros that are locked do not require the password to be run. However,
the password is required to make changes.
Figure 3.14. Unit Properties Security tab
11. Select the Front Panel Lock Mode.
•
•
•
Unlock Panel leaves the front panel controls unlocked.
Lock Panel locks the front panel immediately.
Lock When Timeout locks the front panel after it is inactive for the
specified number of minutes.The range is from 0–15 minutes; 5
minutes is the default.
When locked, the front panel can be accessed only after entering the proper
passcode (sequence of button presses) or by unlocking the panel using
G-Ware.
12. To create a passcode for the front panel, click Clear to clear the default
sequence.Then click any sequence of the five front panel buttons.Your
choices will be displayed in the column on the right. When you are finished,
click OK to enable your selections.
You will need to repeat these steps for all XAP 800 units on your network.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ G-Ware Screens
27
G-Ware Screens
G-Ware has three modes: Configuration, Preset, and Macro Recorder. Configuration is
used to configure the unit and is the default mode.The Preset and Macro modes are
discussed in Chapter 4: Advanced Configuration.You can switch between modes by
clicking on the corresponding toolbar button.The current mode is displayed on the
status bar.
Figure 3.15.
Configuration, Preset,
and Macro toolbar
buttons.
There are two main configuration screens, the Flow Screen and the Matrix
Screen. All unit configuration and audio routing is accessed through these screens.
Flow Screen
Toolbar
Menus
Site pane
FlowScreen
Stautsbar
Figure 3.16. G-Ware Flow Screen
The G-Ware Flow Screen is the main access window for G-Ware’s features and
functions. Using the menus and toolbar at the top of the screen, you can access
general configuration windows. Unit specific configurations are accessed through the
buttons and labels on the Flow Screen itself. If you have multiple units, click on the
unit icon in the Site pane to access that particular unit’s Flow Screen.
The Flow Screen shows a detailed block diagram of the path of the audio
signal, presenting a graphical explanation of each stage of audio processing. Mic
and line inputs, outputs, expansion buses, and processing block configuration
windows can all be accessed from this screen.The XAP 800 Flow Screen has seven
icons and buttons at the bottom of the Flow Screen which open the following unit
programs: Remote Builder, Gating Control, Signal Generator, Preset Mode, Macro
Editor, Meters, and GPIO Builder.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ G-Ware
28
Copying and pasting settings
G-Ware has shortcut menus which appear when you right-click a selection or
program window in G-Ware.These shortcut menus provide quick access to options
such as Print, Copy, and Paste that pertain only to that selection or screen region.
Using the Copy and Paste commands, you can copy and paste unit data such as a
single setting or the entire unit’s settings depending on which window you are in. For
example, if you are in the Inputs 1–8 window, using the shortcut menu will allow you
to copy and paste all of the input settings to other inputs.You can also use keyboard
shortcuts (Ctrl+C and Ctrl+V) to copy and paste settings. If you want to apply all
settings of a selected input to the rest of the inputs, select Apply to All.
Figure 3.17. Unit
shortcut menu
Figure 3.18. Inputs 1–8
shortcut menu
S
The Safety Mute feature in G-Ware enables you to mute all outputs if feedback or
audio problems occur during the configuration process.To use Safety Mute, click the
Safety Mute button on the G-Ware toolbar.Then find and correct the cause of the
problem. Click the Safety Mute button again to unmute the outputs.
Figure 3.19.
Safety Mute
Status bar
There are two status lights at the bottom of the G-Ware window representing the unit
and the site.The lights illuminate in various colors to indicate current status.
•
•
•
Solid green. The item being configured is synchronized with the hardware.
Solid red. The information being configured is saved in the software offline.
Flashing red. The information is not saved or there is no hardware
connection.
•
•
Solid yellow. Communications are pending.
Flashing yellow. There is a communication error. In this instance, you should
disconnect from the unit and reconnect.The Message Log will indicate the error
that occurred. See page 75 for more information.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ G-Ware Screens
29
Matrix Screen
The Matrix Screen is used to route audio to one or more destinations (outputs,
expansion bus, or processing). Any number of connections to outputs can be made in
the matrix.The Matrix Screen can also be used to access the Input, Output, and
Processing configuration windows by clicking on the buttons along the top and left
sides of the routing matrix.
Toolbar
Menus
Labels
Site pane
Matrix Screen
Status bar
Figure 3.20. G-Ware Matrix Screen
A colored cell in the routing matrix marks the intersection or cross point of
the routing from input to output.The color of the cross point cell identifies the
input type: yellow = gated mic input, blue = non-gated mic input, and green = all
other inputs.The amount of attenuation is also shown in the cross point cell. Black
cell are restricted routing paths which prevent E-bus and Processing channels from
being routed back to themselves.
The numbers and letters along the top and left side of the matrix show the
cross point coordinates.The input number or letter and the output number or letter
will be highlighted blue for the selected cross point.
All inputs and outputs are labeled to make it easier to identify channels.
Clicking on a label will open a labels window where you can change the channel
labels.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Audio Routing
30
Audio Routing
Audio is routed in the Matrix Screen (see Figure 3.20 on previous page).To access
the Matrix Screen, click on the Matrix button on the Flow Screen.To return to the
Flow Screen, click the Flow Screen button.
The XAP 800 routing matrix has 32 possible input sources and 32 output
destinations, with level control at each cross point. Any input or combination of
inputs can be routed to any output or any combination of outputs.To clear the
matrix, click the Clear Matrix button located above the Routing Key.
To route an input, click in the routing matrix at the intersection between the
input and the output. A mic input can be designated as gated (yellow) or non-gated
(blue) by clicking repeatedly in the cross point. All other input cross points will be
colored green.
Figure 3.21. Matrix Routing Key
If you click the Clear
Matrix button, you will
✍
clear all cross points in
the routing matrix.
Expansion bus O–Z routing
Audio on any XAP unit in the E-bus network can be placed on the bus or taken off
the bus and routed to any destination within the unit.The XAP 800 has 12 digital
mix-minus buses:
•
O–R buses are defaulted as the mic mix buses and can communicate the
NOM count. Gated mics are default routed to the O bus.
•
S–Z buses are defaulted as the auxiliary mix buses.They are used to carry
auxiliary audio such as that from codecs and XAP TH2s.These buses are
used as mic mix buses when NOM count is not required.
Process A–H routing
There are eight processing blocks on the XAP 800 (Processing A–H).With these
processing channels, you can apply filters, EQ, or other processing settings to an input
or a group of inputs which can then be routed to a single output or group of outputs.
See page 49 for more information on processing settings.
Cross point attenuation
Right-click on a cross point to open the Cross Point shortcut menu. Click Cross Point
Enter to open the Cross Point Attenuation Dial window.
Figure 3.22. Cross Point
shortcut menu
Click the ▲ and ▼ buttons or click on the green indicator and rotate the dial
with the mouse to adjust the attenuation to the desired level (or enter the
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Audio Routing
31
numerical value directly in the window).The attenuation range is from 0 to -60dB.
Click Close to exit. Note that the level control you have selected for the cross point
is indicated numerically in the cross point cell.
The Cross Point shortcut menu also allows you to copy and paste the current
Cross Point configuration, including attenuation, to other cross points.You can copy
a single cell or the entire matrix using the shortcut menu options.To copy and
paste a cross point to multiple cross points, press Ctrl+C to copy (or right-mouse
click).Then press Ctrl+V while holding down the left-mouse button and drag the
mouse over the cross points to which you want to copy the settings.
Figure 3.23. Cross Point window
Matrix report
When you finish audio routing, you can print a detailed report of the matrix using the
Print Matrix option on the shortcut menu (see Figure 3.22).
The Print Matrix Report window displays all matrix routing and cross point
information. Click the Print icon button to print the report.
Figure 3.24. Matrix Report window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
32
Inputs and Outputs
Inputs 1–8
Inputs 1–8 accept either
microphone (-55, -25dB)
or line level (0dB) inputs.
✍
To open the Inputs 1–8 configuration window, click the Inputs 1–8 button on the
Flow Screen.The In 1–8 button on the Matrix Screen will also open this window.
These inputs are balanced and support both mic and line levels.
ClearOne recommends
using the XAP to mute
✍
mics instead of using the
provided by some
mute
microphones. External muting
devices limit the effectiveness of
Gentner D.E.C. To use the mute
button on a microphone, contact
ClearOne Technical Services.
Figure 3.25. Inputs 1–8 configuration window
To select an input channel, click a blank area in the input pane. If you click on
the input label, a secondary window will open allowing you to rename the input.
The background color for the selected input channel will be light gray.The many
configurable properties of mic inputs are defined in this section.
Mute
Mute mutes the input channel.The light on the button illuminates red when Mute is
activated. Default is Off (unmuted).
AGC/SL
AGC/SL opens the Automatic Gain Control/Speech Leveler window. If Speech
Leveler or AGC is enabled, the light on the button illuminates green. Default for both
is off.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
33
The Speech Leveler is a compander that is optimized for speech audio. It
quickly equalizes the difference in speech levels in the room without bringing up noise.
If you use AGC with the Speech Leveler, set the AGC Response Time to >2 seconds.
AGC adjusts softer and louder input audio to a consistent level that you select
(the target level).The target level range is from -30 to 20dB in 1dB steps.The
default target level is 0dB.
Set the Target Level first, then apply the amount of maximum gain that you
want the AGC to apply to the signal. Maximum gain range is 0 to 18dB in 1dB
steps.The default value is 18dB. AGC occurs after the gain and filter settings in
the audio signal path.
Figure 3.26. AGC/Speech Leveler window
The Active Gain meter reflects the overall gain at any given moment. Click
the white box next to the meter to enable it.
All meters in G-Ware are
peak meters. The target
The Response Time adjustment determines the total AGC engage/disengage
response time.The Threshold determines the decibel level at which you want the
AGC to engage. Setting the threshold toward the higher end of the scale (near 0)
reduces background noise to a greater degree.The Response Time is measured in
milliseconds.Target Level and Threshold are both RMS.
✍
level
and
threshold
controls in the AGC/SL window
reflect RMS values.
P Pwr (Phantom Power)
Phantom Power toggles the phantom power on and off. Phantom power is an
auxiliary power source to power certain types of microphones.The XAP 800’s
phantom power voltage is 24VDC. Default is On.
AEC
AEC opens the Acoustic Echo Canceller window.To enable the acoustic echo
canceller, click Enabled, then select the reference. Any one of the 12 outputs, four
expansion bus references, or four virtual references can be selected.
PA Adapt and AEC Reference
If you select an expansion bus reference, the Define PA Adapt/AEC Expansion
Bus Ref window opens so you can identify which expansion bus output you want to
use as the AEC’s reference.You can also open this window from the toolbar.
Figure 3.27. Define PA/AEC
window and toolbar button
Figure 3.28. AEC window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
34
If you select a virtual echo cancellation reference, the Virtual Reference window
will open.You can also open this window from the G-Ware toolbar.
Figure 3.29.
Virtual Reference
toolbar button
Figure 3.30.Virtual Reference window.
Use this window to select which signals will be used by the four Virtual
Reference points.The routing matrix portion of this window cannot be edited.Virtual
references are used when you need to reference multiple outputs. For example, if
you have stereo outputs (L, R) near a block of mics, you would want the mics’ echo
canceller to reference both the left and right outputs. By using a virtual reference,
the echo canceller will be able to reference both signals.This means you don’t need
to use a dedicated output to combine signals.
Or, you may have mics routed to the PA output but you don’t want the echo
canceller to reference this audio. By using a virtual reference, the echo canceller
can sample all signals routed to the PA output, minus the mic signals.
To create a virtual reference
1. Select the input signals you want included in each virtual reference by
clicking the cross points.
2. Because AEC requires a physical output reference to track output gain
changes, you need to select an output reference for AEC to function properly
with a virtual reference. Use the lists at the bottom of the window to select
which output you want AEC to use to track gain changes.
3. Click Close to exit the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
35
Non-linear Processing (NLP)
The Non-linear Processing (NLP) feature increases the power of echo cancellation
for difficult acoustical environments. NLP features four settings: Soft (6dB),
Medium (12dB), Aggressive (18dB), and Off. Use NLP with care; corresponding
trade-offs can include suppression and half-duplex operation. Default is Soft.
Meters
The Echo Return Loss (ERL) meter on the Acoustic Echo Canceller window shows
the coupling between the reference signal and the input to the echo canceller—the
ratio of the two levels. It is an average meter that updates only when a signal is
present.
The Echo Return Loss Enhancement (ERLE) meter shows the loss through
the echo cancellation and non-linear processing chain—the ratio of the two levels.
It is an average meter that updates only when a signal is present.
The Total Echo Reduction meter shows the total ERL and ERLE reduction, in
decibels. It is an average meter that updates only when a signal is present.
NC
The NC button on the selected input in the Inputs 1–8 window opens the Noise
Canceller window.The noise canceller reduces ambient noise in the signal with no
noticeable degradation in signal quality.
To use noise cancellation, click Enable Noise Canceller, then adjust the
Cancellation Depth to the setting which provides the best combination of low noise
and maximum speech clarity.The attenuation depth can be set in 1dB increments
from 6dB to 15dB. Default is 6dB.
Figure 3.31. Noise Canceller window
The noise canceller default is Off. When noise cancellation is enabled, the light
on the NC button illuminates green.
Filters
The Filter button on the selected input in the Inputs 1–8 window opens the Filter
Graph setup window. Each mic/line input has four configurable filters that can be used
as filters or equalizers. By default, they are not enabled and the filter types are not
defined. Below is a description of each feature in the window.
Active Filter
Active Filter selects among filters on the graph. Note that no filters exist until you
click Add Filter (see Figure 3.32) to add filters to the graph.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
36
Figure 3.32. Inputs 1–8 Filters window
Type
Use the Type list to select from the following input filters: All Pass, High Pass, Low
Pass, Notch, and PEQ. G-Ware features other filters which are configured in the
Processing section of the software (see page 49).
•
•
•
•
All Pass. Frequency range is 20Hz to 20kHz with resolution to 1Hz or four
places (whichever is larger).
High Pass. Selectable frequency cutoff is 20Hz to 20kHz, in 1Hz
increments. Rolloff is 12dB/octave. Level is fixed at 0dB.
Low Pass. Selectable frequency cutoff is 20Hz to 20kHz in 1Hz
increments. Rolloff is 12dB/octave. Level is fixed at 0dB.
Notch. Center frequency range is 20Hz to 20kHz with resolution to 1Hz or
four places (whichever is larger). Bandwidth is from .05 to 5 octaves in .01
octave increments. Level is fixed at -80dB.
•
PEQ (parametric equalizer). Center frequency range is 20Hz to 20kHz
with resolution to 1Hz or 4 places (whichever is larger). Bandwidth is .05 to
5 octaves in .01 octave increments. Level range is -15 to +15dB in 0.5dB
increments.
Frequency. Use Frequency to select the center frequency (in Hertz) for the filter you
are configuring. Range is from 20Hz to 20kHz. Default is 1kHz.
Gain. Gain adjusts the gain value from -18 to 18dB, in .5dB steps. Default is 0dB.
Q, or Quality factor. Q, or Quality factor, selects the ratio of the center frequency
divided by the bandwidth. Q reflects an inverse relationship to the bandwidth, and
adjusts from .02:1 to 40:1 on the XAP 800.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
37
Bandwidth. Bandwidth establishes the difference between the upper and lower
points of a filter’s audio passband.
Bypass. The Bypass box, when selected, bypasses the selected filter.
Phase. Phase generates—on the graph—the phase relationship of the graphed
frequency response.
Bypass All. Bypass All bypasses all filters.
Add Filter. Add Filter adds a filter to the graph, centered at 1kHz and 0dB.
Remove Filter. Remove Filter removes the selected filter from the graph.
Table View
Figure 3.33. Filter Graph window, table view
Table View toggles between the Graph and the Table views of the Inputs 1-8 Filter
window.The Table view displays the selected filter settings in table format.You can
configure filters from this view as well as in the graph view.
To configure filters
1. In either the graph or table view, select the filter type from the Type list.
Note that the configurable filter parameters displayed depend on the selected
filter type.
2. Click Add Filter to add a filter to the graph or table.
3. Configure filter parameters using the previously described lists. If you are
using the graph view, you can click on the node and drag it to the location
you desire on the graph.
4. Click Close to exit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
38
Gate
The XAP 800 has unique gating parameters which control microphone activation.
The Gate button on the selected input in Inputs 1–8 window opens the Gate
configuration window where you can establish the gating parameters for the input.
Activation
There are three mic activation settings: Auto Gate, Manual On, and Manual Off.
•
•
•
Auto Gate determines mic gating based on the input level and gating settings
for the gating group the input is assigned to. It contributes to and is affected
by all gating group settings such as NOM, chairman override, etc.
Manual On activates a mic, provided it does not exceed max NOM
requirements of the gating group that the input is assigned to. It is included in
the NOM count.
Figure 3.34. Gate window
Manual Off deactivates a mic.
Chairman Override
Chairman Override provides gating priority for this mic input over any other mic input
within the same gating control (mixer) groups.When a mic with Chairman Override
enabled gates on, all mics which don’t have Chairman Override enabled will gate off.
Default is off.
Adaptive Ambient
Adaptive Ambient adjusts the ambient reference level as noise and room conditions
change.When adaptive ambient is on, the mic channel monitors the ambient noise
level on the input and adjusts the ambient level reference automatically.This means
that the gate threshold level automatically increases or decreases based on back-
ground noise. If Adaptive Ambient is turned off, the input will use the fixed ambient
level specified in the Ambient Level box as its gating reference. Default is on.
PA Adaptive Mode
PA Adaptive Mode uses loudspeaker audio level on a specified output as the new
ambient level when audio is present at the power amplifier.This prevents loudspeaker
audio from gating on the mic, while still allowing people in the room to gate on
microphones as they speak—provided that their voices are louder than the
loudspeaker audio. For example, you might decide to play background music from a
CD player during a presentation. PA Adapt Mode allows you to use the output routed
from the CD player as the ambient reference to prevent the CD player’s audio from
gating on microphones. An output must be specified as the PA Adaptive Reference
(this is the same as the AEC reference) for each mic in the system. Default is on.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
39
Figure 3.35. XAP 800 automixing gate functions
Gate Ratio
Gate Ratio specifies how much louder the audio level must be above the ambient
level before the channel gates on.The gate ratio range is from 0 to 50dB. Default is
15dB.
Hold Time
Hold Time determines how long the channel stays gated on after the audio is below
the threshold.The hold time range is from .1 to 8.0 seconds. Default is .3 seconds.
Off Attenuation
Off Attenuation sets the amount of level reduction applied to a channel when it is
gated off.The range is from 0 to 50dB. Default is 12dB.
Ambient Level
Ambient Level is available only if the Adaptive Ambient feature isn’t enabled. Use
Ambient Level if you want to specify a fixed reference point rather than one that
adjusts for background noise.The range is from -80 to 0dB. Default is Off.
Decay Rate
Decay Rate determines how fast a channel gates off after the hold time expires.
Default is Medium.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
40
PA Adapt and AEC Reference
The PA Adapt Reference
and AEC Reference are
the same for each channel.
✍
When using either the PA Adaptive mode (see page 38) or Acoustic Echo
Cancellation (see page 33), the output that carries this information, i.e. the reference
output, must be defined. Select the PA Adapt and AEC Reference from the drop-
down list. Any one of the 12 outputs, four expansion bus references, or four virtual
references can be selected.
If you change the PA Adapt
Reference for a channel, you will
also make the same change to that
channel’s AEC Reference.
If you select an expansion bus reference, the Define PA Adapt/AEC
Expansion Bus Ref window opens so you can identify which expansion bus output you
want to use as the PA reference.You can also open this window from the toolbar.
Figure 3.36. PA Adapt/AEC
window and toolbar button
If you select a virtual echo cancellation reference point, the Virtual
Reference window will open.This window allows you to select which signals will be
used by the four virtual reference points. Virtual references are used when you need
to reference multiple outputs.The routing matrix portion of this window can not be
edited.You can also open this window from the G-Ware toolbar.
Figure 3.37.
Virtual Reference
toolbar button
Figure 3.38. Virtual Reference window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
41
Gating Group Select
In addition to specifying gating characteristics for each mic input, you can assign the
inputs to a gating group for greater flexibility and control.When inputs are assigned
to a gating group, the gating information from the inputs is used to control how the
entire mixer behaves.
Figure 3.39. Gating
Group Select pane
The XAP 800 features four internal gating groups (Internal 1–4) and four
global gating groups across the expansion bus (Global A–D). Microphones can only
be used in one gating group at a time. If an input is not assigned to a gating group,
that mic’s gate properties are independent and have no effect on any other gating
group. When gating groups span two or more units (global gating groups), the
settings must be the same for each unit attached to the global gating group. Mic
inputs are routed to Global Group A by default.
To assign a gating group
•
Select the Internal or Global group the mic input will belong to or select
None.
To configure gating group settings
1. Click the Gating Control button on the toolbar.This opens the Gating
Controls window.
Figure 3.40. Gating Control button
Figure 3.41. Gating Controls window
2. Select the Max # of Mics (default is 4).
This sets the maximum number of microphones that can be gated on at any
one time within a gating group. For internal groups, the maximum number of
mics can be from 1 to 8. For global groups the maximum number of mics
will vary depending on how many mic inputs are assigned to the gating group
(up to 64).You can also select All for the global groups—which means all
mics could gate on.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
42
3. Leave 1st Mic Priority selected (default) to enable this feature; otherwise,
clear the selection to disable it. ClearOne recommends leaving this setting on.
This setting helps maintain maximum audio intelligibility by allowing only
one mic to gate on to a participant’s voice. 1st Mic Priority allows more
than one microphone to be activated at the same time—it simply restricts
mics from gating on to the same audio source. It does this by determining
the audio level received by all mics when the first mic is gated on.This audio
level is then used as the ambient level for the gating group. If this feature is
disabled, usually two or more microphones gate on when only one person
speaks.
4. Select last-mic operation from the Last Mic Mode list.There are two
options for Internal groups: Last On and Off. If you are configuring Global
groups, you can select from the mic inputs assigned to the Global group in
addition to Last On and Off.
Last On leaves the mic that was activated last full on until another mic input
is gated on.The Input setting allows you to select which mic input the
XAP 800 leaves on when all mics gate off. If Off is selected, all mics will
gate off when no audio is present. It is preferable in most applications to
leave a mic on so the remote participants don’t think they have lost their
audio connection. Off is typically only used when you are conferencing
multiple sites and need to reduce background noise.
5. Click the Gating Group label to change the group names.
Gain
The Coarse and Fine sliders on the selected input on the Inputs 1–8 window are used
to match the level settings for microphone inputs and to adjust input volume level.
•
Set the Coarse gain to 55dB for a mic input, 25dB for active equipment that
requires an input between mic and line level, or 0dB for a line level input.
•
Use the Fine gain slider to adjust input volume level. You can also enter the
level directly in the 0.0dB box.
Max adju
Minadju
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Fine gain scale to create
minimum and maximum gain level limits.These limits only apply when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Figure 3.42. Gain
adjustment
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
43
Optimizing input gain structure
How you adjust an input’s gain directly affects sound quality.The optimal input gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the input level properly, place a signal on the input at the maximum
level it will generate. Adjust the input gain until the peak level of the input, as
shown on the Input meter, just begins to enter the red (clipping) zone, then reduce
the gain slightly until peaks no longer climb into the red zone.This setting will
ensure that the XAP 800 maximizes the signal-to-noise ratio without clipping the
signal.
Meters
There are four meters on each mic/line input to assist with setup and level control.
Select the meter check box to enable the meter. All input meters are peak-level.
Figure 3.43 Meter locations in the Inputs 1–8 signal path
Pre Gain
Pre Gain meter indicates the input’s level before gain adjustments. Meter range is
from -85 to -35dB when 55dB gain is selected; -55 to -5dB when 25dB gain is
selected; and -65 to 20dB when 0dB gain is selected.
Post Gain
Post Gain meter shows the input’s level after gain adjustments have been made.
Meter range is from -30 to +20dB.
Post Processing
Post Processing meter indicates the level at the gating point after the signal has
passed through input processing. It reflects the post-AGC signal. Meter range is from
-30 to +20dB.
Post Gating
Post Gating meter shows audio level after it has passed through the gating
parameters. Meter range is from -30 to +20dB.
Figure 3.44. Mic
input meters
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
44
Inputs 9–12
The XAP 800 supports 4 line level only inputs for auxiliary audio sources such as
video codecs and CD players.To open the Inputs 9–12 configuration window, click the
Inputs 9–12 button on the Flow Screen.The In 9–12 button on the Matrix Screen
will also open this window.These non-gated inputs are balanced.The nominal input
level is 0dBu.
Figure 3.45. Inputs 9–12 Configuration window
To select an input channel, click a blank area in the input pane. If you click on
the input label, a secondary window will open allowing you to rename the input.
The background color for the selected input channel will be light gray.The
configurable properties of these inputs are defined in this section.
Mute
Mute mutes the input channel.The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
AGC
AGC opens the AGC window.The AGC window has the same parameters as the
AGC/SL window with the exception of Enable Speech Leveler. See page 32.The
button light illuminates green when AGC is enabled.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
Gain
45
The Gain slider on the selected input in the Inputs 9–12 window is used to adjust
input volume level.
Max adju
Minadju
•
Use the Gain slider to adjust input volume level. You can also enter the level
directly in the decibel box below the gain scale.
Min/Max limits
Figure 3.46. Gain adjust
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
minimum and maximum gain level limits.These limits only apply when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are used.
on line level input
Optimizing input gain structure
How you adjust an input’s gain directly affects sound quality.The optimal input gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the input level properly, place a signal on the input at the maximum
level it will generate. Adjust the input gain until the peak level of the input, as
shown on the Post Gain meter, just begins to enter the red (clipping) zone, then
reduce the gain slightly until peaks no longer climb into the red zone.This setting
will ensure that the XAP 800 maximizes the signal-to-noise ratio without clipping
the signal.
Meters
Pre Gain
Pre Gain meter indicates the input’s level before gain adjustments have been made.
Meter range is from -30 to +20dB.
Post Gain
Post Gain meter shows the input’s level after gain adjustments have been made.
Meter range is from -30 to +20dB.
Figure 3.47. Gain
meters
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
46
Outputs 1–12
The XAP 800 has 12 line level outputs for sending audio to video codecs, recorders,
or amplifiers.To open the Outputs 1–12 configuration window, click the Outputs
1–12 button on the Flow Screen.The Outputs 1–12 button on the Matrix Screen will
also open this window.
Figure 3.48. Outputs 1-12 configuration window
These line level outputs are balanced.The nominal output level is 0dBu.The
outputs can adjust from -65 to 20dBu.
To select an output channel, click a blank area in the output pane. If you click
on the output label, a secondary window will open allowing you to rename the
output.The background color for the selected output channel will be light gray.The
configurable properties of these outputs are defined in this section.
Mute
Mute mutes the output channel.The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
NOM
NOM (constant gain) maintains a constant output level as inputs routed to the
output are gated on and off.The XAP 800 reduces the output gain (at the output)
for mics based on the number of mics gated on and routed to that output.When
using NOM over the expansion bus, only the first four audio channels (O, P, Q, and R)
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Inputs and Outputs
47
support passing NOM information. Enable NOM if you want to place this output in
a constant gain mode. Default is on. When enabled, the NOM button light
illuminates green.
Gain
The Gain slider on the selected output in the Outputs 1–12 window is used to adjust
output gain level.
Max adjust
Minadjust
•
Use the Gain slider to adjust output volume level. You can also enter the level
directly in the 0.0dB box. If you select any level below -60dB, the signal will be
muted.The Level meter, when enabled, shows the signal level when a signal is
present.
Figure 3.49.
Output gain adjust
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
minimum and maximum gain level limits.These limits only apply when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Optimizing output gain structure
How you adjust an output’s gain directly affects sound quality.The optimal output
gain setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the output level properly, place a signal on the output at the
maximum level it will generate. Adjust the output gain until the peak level of the
input, as shown on the Level meter, just begins to enter the red (clipping) zone, then
reduce the gain slightly until peaks no longer climb into the red zone.This setting
will ensure that the XAP 800 maximizes the signal-to-noise ratio without clipping
the signal.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Expansion Buses
48
Expansion Buses
Routing of audio to the
expansion buses is done in
the Matrix Screen. See
From Expansion Bus O–Z
✍
Click the From Expansion Bus O–Z button on the Flow Screen to open the From
Expansion Bus Labels window.You can also access this window from the Matrix
Screen.
page 30. For information on setting
up an expansion bus network, see
page 11.
Figure 3.50. From Expansion Bus Labels window
•
Enter the names you want to use for each expansion bus, then click OK to
save the information and close the window.
To Expansion Bus O–Z
Click the To Expansion Bus O–Z button on the Flow Screen to open the To
Expansion Bus Labels window.You can also access this window from the Matrix
Screen.
Figure 3.51.To Expansion Bus Labels window
•
Enter the names you want to use for each expansion bus, then click OK to
save the information and close the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
49
Processing
Processing A–H
There are eight processing blocks in the XAP 800, each with filters, compressors, and
delay to provide pinpoint audio configurations.To open the Processing configuration
window, click the Processing A–H button on the Flow Screen.The To and From
Processing buttons on the Matrix Screen will also open this window.
ClearOne recommends
using the XAP to mute
✍
mics instead of using the
provided by some
mute
microphones. External muting
devices limit the effectiveness of
Gentner D.E.C. To use the mute
button on a microphone, contact
ClearOne Technical Services.
Figure 3.52. Processing window
To select a processing block, click a blank area in the Process pane. If you
click on the Process label, a secondary window will open allowing you to rename
the processing block.The background color for the selected processor will be light
gray.The configurable properties of these processors are defined in this section.
Mute
Mute mutes the processor.The light on the button illuminates red when Mute is
activated. Default is off (unmuted).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
50
Cmprs (compressor)
Cmprs opens the Compressor Setup window (see Figure 3.53).With the compressor
you can change the gain transfer characteristics of the signal path and control the
dynamics of a signal.
When the signal exceeds the threshold level, gain reduction occurs at the rate
specified by the reduction ratio.The attack time determines how aggressively the
compressor reacts to increases in level.The release time controls how aggressively
the compressor reacts to reductions in level. Select the Enable Compressor check
box to activate the compressor.
Figure 3.53. Compressor Setup window
Group
Use the slider to assign this compressor to a compressor group.The default is None
When you assign a compressor to a compressor group—such as a group of three,
configured for bass, midrange, and treble—the compressors will monitor each
other. When one compressor channel compresses, all compressors in the group
compress together. When configured properly, this results in a smooth audio
response throughout the frequency range, with no bass, midrange, or treble
.
Compressors and com-
pressor groups can be
established only within the
✍
XAP 800 unit being configured,
i.e., they cannot be configured from
a single point across multiple units.
dropouts. A given compressor group must be configured for a single XAP 800 unit;
a group cannot use compressors from multiple XAP 800 units.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
51
Post Compressor Gain Adjust the compressor gain with the gain slider or by
using the
▲
and
▼
buttons.The graph reflects the input/output decibel levels with
the gain setting you select.
Threshold Threshold determines the RMS level at which the compressor begins to
operate.The range is from -30 to +20dBu. Default is 0dBu.
Ratio Ratio changes the rate of compression applied to the input signal as the
signal exceeds the threshold level.The range is 1:1 to 1:20dB. Default is 1:1.
Attack Attack determines how quickly compression is enabled. It is calibrated in
milliseconds.The range is 0 to 100ms in .5ms steps. Default is 10ms.
Release Release determines how quickly compression is disabled.The range is
100ms to 2 seconds, in 5ms increments. Default is 500ms.
Input meter This peak meter shows the level of the signal as it enters the
compressor.
Compression meter This peak meter shows the instantaneous compression value
at a given time.
Filters
The Filter button on the selected Processing channel opens the Processing Filters
window. Here, you can configure all filters available in G-Ware: All Pass, Bessel,
Butterworth, CD Horn, High Pass, High Shelving, Linkwitz-Riley, Low Pass, Low
Shelving, Notch, and PEQ.
Figure 3.54. Processing Filters window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
52
The frequency response and phase vs. frequency of the total transfer function
of all filters is displayed in the window. Each filter can be disabled without
affecting the filter settings. All filters can also be disabled using a single command.
By default, they are not enabled and the filter types are not defined. Below is a
description of each feature in the window.
Active Filter
The Active Filter displays the filter that is applied to the processing channel.
Type
Select the filter type from the Type list. Note that the configurable filter parameters
displayed depend on the selected filter type. You can use these parameters to
customize the filter, or use the mouse to click and drag the node on the graph to a
location that reflects the changes you want to make.
You can continue to add filters to the graph, and track their relationships to
each other to design a system with the sound characteristics necessary for good
audio.
Phase
Phase plots the phase response of the frequency response of the selected filter.
Bypass
Bypass All bypasses all filters.
Add Filter
Add Filter adds a filter to the graph.
Remove Filter
This removes the selected filter from the graph.
Table View
Table View toggles between the graph view and the table view.The table view allows
you to configure filters in a table format rather than on the graph, and provides an
easy way to check filter status.
Processing Channels
The Processing Channels section allows you to display the graphs of various
processing channels together, so you can view and easily modify filter and equalizer
settings throughout the frequency range. Click the respective letter to place a
processor in the graph. Click the Active processor you want to modify; it appears in
bold on the graph.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
53
Figure 3.55. Low/Mid/High Loudspeaker Driver configuration
Refer to the figure above. Note that as you create filters across several
processing channels, you can observe their crossover points and general shape of
the frequency response. In this case, several Linkwitz-Riley filters are being created
across three processing channels to establish a balanced frequency response from
low-frequency, midrange, and high-frequency transducers.
Delay
Click Delay to open the Delay configuration window. Delay calibrates the amount of
signal delay introduced, based on the length (the distance between the source and
audience) and temperature you enter.
If you don’t want delay
added to the signal, select
✍
the Bypass Delay box.
Figure 3.56. Delay window
The Calculated Delay
reading reflects any
changes you make in the
For example, different speaker drivers within a speaker enclosure might be
located different distances from the listening area because of design constraints
within the box.You can set up to 500ms of delay.
✍
distance and temperature fields.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
System Configuration ~ Processing
54
Introducing an appropriate amount of delay to the forward-mounted driver(s)
re-establishes the acoustical alignment necessary for proper sound imaging in a
room.The same principle of introducing delay applies to separate speaker
enclosures located various distances from the listening area.
Other types of delay to consider when establishing delay parameters are delays
which occur naturally as a result of processing operations within the
XAP 800. Propagation delay is an example.This delay is caused by operations such
as the conversion of the signal between analog and digital formats.
When you are finished making changes in the Delay window, click Close to
return to the Processor window.
Gain
Gain establishes the gain level for this channel. Select a level between -65 and 20dB.
If you select any level below -60dB, the signal will be muted.The Process meter,
when enabled, shows the signal level when a signal is present.
Min/Max limits
Use the yellow and blue upper and lower limit arrows on the Gain scale to create
minimum and maximum gain level limits.These limits only apply when using relative
gain commands; absolute gain commands can exceed the min and max limits.
Min/Max limits apply to all serially connected control devices and prevent users from
adjusting levels beyond the min/max levels, provided relative gain commands are
used.
Figure 3.57. Process
gain adjust and meter
Optimizing process gain structure
How you adjust the processing gain directly affects sound quality.The optimal gain
setting is one which is adjusted as high as possible above the noise floor without
introducing clipping. Clipping can cause distortion which can damage amplifiers and
loudspeakers.
To adjust the processing gain level properly, place a signal on the output at the
maximum level it will generate. Adjust the gain until the peak level of the input, as
shown on the Process meter, just begins to enter the red (clipping) zone, then
reduce the gain slightly until peaks no longer climb into the red zone.This setting
will ensure that the XAP 800 maximizes the signal-to-noise ratio without clipping
the signal.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 4: Advanced
Configuration
Presets
Overview
For many audio conferencing applications, a great deal of system flexibility is needed
to meet the challenges presented by changing meeting or conference room
requirements.These requirements may include changes in muting, audio sources,
room orientation, or room combining. And ideally, these changes are made
instantaneously—without interrupting or affecting any meetings in progress.
Using presets enables you to accommodate these changing room requirements
quickly and efficiently. When you create a preset, you are essentially creating a
single room configuration option. Presets can be programmed with a variety of
routing, level, gating, delay, filter, and EC reference settings to meet specific
application requirements.You can change every unit parameter or a select few
depending on your room needs. XAP 800 presets are unique in the sense that they
operate independently of other presets in the unit. When a preset is run, only the
selected inputs/outputs are changed—all other settings in other presets remain
unchanged and are not reset.This means you can change audio routing and
configuration settings in a room without affecting settings in other rooms (such as
gain).You can create up to 32 presets for the XAP 800.
Presets are used only
within the local
XAP 800 unit. However, if
a preset is part of a macro, it can be
activated on a networked XAP 800
unit.
✍
Presets can be executed in a variety of different ways including the Execute
Preset utility in G-Ware, the front panel controls of the XAP 800, RS-232 external
control devices, RS-485 control devices (ClearOne Control Panel and XAP IR
Remote), logic in/out, and contact closure.You can also create macros which can
run multiple presets.These options give you tremendous flexibility when designing
your installations and will be described in more detail in this chapter.
Creating Presets
Presets are created in G-Ware using the Preset mode.To switch to Preset Mode,
click the Preset Mode button on the toolbar or the Preset Mode button on the Flow
Screen.The Preset Mode window (see Figure 4.2) consists of the Preset
Configuration Pane (left side of the window), the G-Ware menus and toolbar
(although most options are not available because they do not apply to presets), and
the Preset Matrix Screen.There is no Flow Screen in Preset Mode since all
configurable settings can be accessed from the Matrix Screen.
Figure 4.1. Preset Mode
toolbar button
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
56
G-Ware Toolbar
G-Ware
Menus
Preset
Preset
Configuration
Pane
Matrix Screen
Status Bar
Figure 4.2. Preset Mode
Matrix Screen
The Matrix Screen in the Preset Mode is very similar to the Matrix Screen in
Configuration Mode. All Input, Output, and Processing windows can be accessed by
clicking on their respective buttons.You can also create custom labels by clicking on
the current labels.
The routing matrix is grayed out because no routing changes have been made.
When you click on the number or letter of an input, the row becomes active and
you can change the routing, gate status, and cross point attenuation. All
parameters for the selected input will be saved in the preset including routing.
Also, the parameters for any outputs with a cross point in the selected row will be
saved. Input rows that are not selected remain gray, or masked, and will not be
affected when the preset is run.
Preset Configuration pane
The Preset Configuration pane is used to create preset properties such as number,
name, and description as well as create custom preset controls, assign the preset to a
gating group, select macros, and configure virtual EC references.
Preset Selection. Use the Preset Selection list to assign a number to the preset
you are creating or to select an existing preset for editing.
Protected. Select the Protected check box to lock your preset. Locked presets are
indicated by a padlock icon. Presets that are locked do not require the password
to be run. However, the password is required to make changes to the preset. The
preset password is set in the Unit Properties window; see page 26.
Figure 4.3. Preset Configuration pane
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
57
Preset Description. Use the Preset Description box for entering information about
the preset.This description is stored in the site file, not the unit.
Preset Mask Control/Status B. With Preset Mask Control Status B you can
require an active high (H) or active low (L) contact on a control pin (1–19 odd
numbers) or combination of several contacts in order to run the preset.
Figure 4.4. Preset Mask
Control/Status B
A typical use for Preset Mask Control Status B is a room combining
application which uses automatic partitions with sensors or triggers which set the
pin to high (H) when the partition is closed and to low (L) when the partition is
open. For example, if pin 1 is connected to the first partition and Pin 3 is
connected to the second partition, then the Preset Mask Control Status B settings
shown in Figure 4.4 will activate the preset when the first partition is open and the
second partition is closed.
Change Preset Label. Change Preset Label opens the Change Preset Labels
window, where you can create a short description (label) for the preset.
Gating Controls. The Gating Controls button opens the Gating Controls window,
where you can select and configure gating groups for this preset. See page 41 for
more information about gating groups.
Macro Selection. The Macro Selection button opens the Preset Macros window,
where you assign specific macros to the preset you’re creating. Select the macros you
want to use with this preset, then click OK to save changes. See page 63 for more
information about creating macros.
GPIO Command Assignment. This opens the GPIO Builder window.With the
GPIO builder, you can configure pin assignments for the Control/Status port A.The
Use in Preset option is available only when you open the GPIO Builder from the
Preset mode and allows you to create customized pin assignments for each preset. If
you open GPIO Builder from the toolbar while in Configuration Mode, or from the
Flow Screen, you will not have the Use in Preset option. See Chapter 6: Control for
instructions on configuring pin assignments.
Remote Assignment. This opens the Remote Builder window.With the Remote
builder, you can configure the XAP IR Remote Control and the ClearOne Control
Panels.The Use in Preset selection box is available only when you open the Remote
Builder from the Preset Mode and allows you to create customized control for the
current preset. If you open Remote Builder from the toolbar while in Configuration
Mode, or from the Flow Screen, you will not have the Use in Preset option. See
Chapter 6: Control for instructions on configuring the XAP IR Remote.
Figure 4.5. Preset Macros Window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
58
Virtual Reference. The Virtual Reference button opens the preset Virtual Reference
window. Using the Virtual Reference window, you can select which signals will be
used by the four Virtual Reference points in this preset configuration.The only input
rows which will be shown in this window are the input rows which are active in the
Preset Matrix Screen.The routing matrix (right pane) in this window is read-only.
Use the Virtual Reference portion of the window to select input channels for Virtual
Refs. 1–4.
To enable Acoustic Echo
Cancellation or to change
which outputs, expansion
references, or virtual
✍
bus
references will be used for this
preset, open the Acoustic Echo
Canceller window from the Inputs
1–8 configuration window.
Figure 4.6. Assigning virtual references to the preset
As with the standard (non-preset) Virtual Reference configuration, you will
need to select an output from the Output Level Tracking lists for each Virtual
Reference you configure. See page 34 for more information on creating Virtual
References.
Print Preset. Print Preset opens a Print Preview window and allows you to print a
copy of your preset settings.The preset must be saved before it can be printed.
Save Preset. Saves the current preset.
Clear Preset. Clears current preset settings.
Exit Preset. Returns you to the Matrix screen in the Configuration mode.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
To create a preset
59
1. From the Preset Selection list, select the number of the preset you will be
configuring. Enter a description of the preset in the Preset Description box.
2. If you want to password protect this preset, click Protected. See page 26
for information on creating the preset password.
3. Configure the routing matrix and make cross point attenuation adjustments.
4. Configure input, output, processing, and telco channel settings as needed. See
Chapter 3: System Configuration for specific instructions on unit settings.
5. Click Gating Controls to set up gating parameters for the preset.
6. Make GPIO or Remote assignments as needed.
7. Click Virtual Reference if you need to create Virtual References specific to
the preset.
8. When you have finished configuring the preset, click Save Preset to save the
settings. Click Exit Preset to exit Preset Mode.
Storage space
In a realistic preset configuration scenario, it is highly unlikely that you would reach
the storage capacity of the unit. In the event that you exceed the preset storage
space, G-Ware will alert you when you try to save the preset.You will be asked to
reduce the number of cross point changes or the number of macros in the preset. As
a general rule, if you make cross point changes to three-fourths of the matrix, you
can establish a maximum of 128 nested macros for a given preset.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
60
Running presets
Presets can be run from G-Ware or the front panel controls on the XAP 800.You
can also program external control devices (such as AMX or Crestron, ClearOne
Control Panels, XAP IR Remote, and GPIO devices) or use macros to run presets.
See Chapter 6: Control for more information on creating custom control.
To run a preset using G-Ware
1. Select the Execute Preset button on the G-Ware toolbar.
2. Select the preset you want to execute from the Preset list.
Figure 4.7. Execute Preset
toolbar button
Figure 4.8. Execute
Preset window
3. Click Execute to run the preset and close the window.
To run a preset using front panel control
1. From the System Menu, scroll to Select Preset and press Enter
2. Scroll to the preset number you want to run and press Enter
.
.
Running multiple presets simultaneously
To run multiple presets at the same time, you need to create macros (see page 63). A
macro is a series of commands which can be executed from G-Ware or by using any
external control device.Typically you will create a macro for each configuration or
group of presets you want to run at the same time.This ability to run multiple presets
is critical in applications such as room combining. However, not only do you need to
be able to run multiple presets simultaneously, you also need to be able to change
presets without affecting other presets.
It is also possible to assign
states to presets when
creating Remote Panel,
In order for this to happen, the system needs to know which presets have been
run and shouldn’t be rerun and which ones are ready to run.You supply the system
with this information by setting the state (or flag) of the preset when creating the
command line in the macro.The three options are:
✍
serial, or GPIO control. However,
unless you create macros, you will
only be able to run one preset at a
time.
0 = to set the state to off
1 = to execute the preset and set the state to on
2 = to execute the preset and set the state to off
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
61
Figure 4.9. Assigning a state to a preset command in the Macro Editor
If a preset is flagged as “On,” nothing will happen when the preset is executed
again because the system knows it has already been run.This prevents any manual
adjustments that are made during the course of the meeting (gain, muting, etc.)
from being lost.
Room combining example
In the room combining scenario depicted in Figure 4.10, there are four possible room
configurations using six presets (P1–P6). In order to change configurations without
disturbing meetings in progress, a macro must be created for each configuration that
tells the system what to do with each of the six presets.
You can also create a
macro to set all preset
flags to 0 which ensures
✍
all presets are ready to run again.
Figure 4.10. Room combining diagram
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Presets
62
The four macros (one for each configuration) are set up as follows:
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
When the room is in Configuration 1, running the Configuration 2 macro will change
the presets to the following states:
•
•
•
P1 does not change because the flag is already set (1)
P2 and P3 clear their states (0) so they can be run
P4 runs and sets its state to on (1) which prevents other presets from
reruning it
•
P5 and P6 clear their states (0) so they can be run
When the room is in Configuration 3, running the Configuration 1 macro will change
the presets to the following states:
•
P1 and P2 run and set their state to on (1) which prevents other presets
from reruning them
•
•
P3 does not change because the flag is already set (1)
P4, P5, and P6 clear their states (0) so they can be run
For more detailed information on creating macros, see the Macros section on the
next page.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Macros
63
Macros
A macro is a series of commands which can be run from G-Ware, the front panel
controls, or by using any external control device. Macros streamline the operation of
the XAP 800, allowing you to make quick configuration changes and, as previously
discussed, making it possible to execute multiple presets simultaneously (see pages
60–62). Macros can also contain commands that are executed on other XAP units.
See pages 97–98 for a list of commands which can be used in macros.
The XAP 800 is designed to support up to 255 macros, with an average of
150 command lines each. In the unlikely event that you exceed G-Ware’s capacity,
you will be notified with a warning that indicates the command line at which
memory is exceeded.
Creating macros
There are two ways to create macros in G-Ware: the Macro Recorder, which
records your onscreen selections, and the Macro Editor, which allows you to
directly create command lines.The Macro Editor is also used to edit macros
created using the Macro Recorder.
To create a macro using Macro Recorder
1. Click the Macro Recorder button on the G-Ware toolbar.The Macro Record
Figure 4.11. Macro
window opens and the mode is changed to Macro on the status bar.
Recorder toolbar button
When you select an
existing macro as the
✍
macro to record, the new
recording is appended to the end of
the existing macro.
Figure 4.13. Macro Record stop window
Figure 4.12. Macro Record start window
2. Select the macro number from the Macro to Record list, then click Start.
3. Make any routing and input/output configuration changes (such as gain
adjustments, mute, etc.) to be included in the macro. Make these changes the
same way you made changes in Configuration mode (see Chapter 3: System
Configuration for more information).
4. Click Stop in the Macro Record window in the upper right-hand corner of
the screen.This stops the macro recording and opens the Macro Editor
window. See page 65 for editing instructions.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Macros
To create a macro using Macro Editor
64
1. Click the Macro Editor button in the G-Ware toolbar to open the Macro
Editor.
Figure 4.14.
Macro Editor button
Figure 4.15. Macro Editor window
2. Select the Macro (from 1 to 255) you are creating from the Macro list.
Numbers that are already assigned to macros will be marked with an
asterisk.
3. Select the Protected check box to lock your macro. Locked macros are
indicated by a padlock icon. Macros that are locked do not require the
password to be run. However, the password is required to make changes to
the macro. The macro password is the same as the preset password and is set in
the Unit Properties window; see page 26.
4. Click Change Name to create a more descriptive name for the macro which
Figure 4.16 Macro Name window
is displayed in addition to the macro number (limit 20 characters).
5. Type any notes pertaining to the macro in the Macro Description box.
6. Select the Device Type and ID from their respective lists.
7. Select the Command from the Command list. When you select a command,
a description of it appears in the Command Description box.
8. Select the command parameters from the argument lists.The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Macros
65
9. Click Add to place the command into the macro.The command line now
appears in the command line table.
You can now create another command line for the macro or save the
completed macro.
Editing macros
With the Macro Editor, you can add, edit, or remove command lines in the macro. If
you used the Macro Recorder to create a macro, the Macro Editor opens
automatically. Otherwise, click the Macro Editor toolbar button.
To edit a macro
1. Select the macro from the Macro list.
2. Click Change Name to edit the macro label.
3. Double-click the command line you want to edit.The Current Line Number
displays the selected command line.
4. Make changes to the command or arguments by selecting options from the
drop-down lists.
5. Click Replace to overwrite the old command line with the new changes.
6. Click Save or Save As to save the macro.
To delete a macro
•
•
Click Clear Macro to delete the entire macro.
Click Delete to delete the selected command line.
To add or insert a command line
•
Click Add to place the current command line into the next available row in
the command line table.
•
Click Insert to insert the current command line into the row directly above
the currently selected command line in the table.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Advanced Configuration ~ Macros
66
Running macros
Macros can be run from G-Ware or the front panel controls on the XAP 800.You
can also run a macro using external control devices (see Chapter 6: Control for more
information).
To run a macro using G-Ware
1. Select the Run Macro button on the G-Ware toolbar.
2. Select the macro from the Select Macro list.
Figure 4.17. Run Macro
toolbar button
Figure 4.18. Run Macro window
3. Click Run to run the macro and close the window.
To run a macro using front panel control
1. From the System Menu, scroll to Select Macro and press Enter
.
2. Scroll to the number of the macro you want to run and press Enter
.
To run a macro using the Select panel or GPIO
•
Use the macro command. See Chapter 6: Control for more details.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 5: Operation
G-Ware features several tools designed to assist you as you install your XAP 800
Audio Conferencing System including Signal Generator, Document Compare, Print
Reports, Copy and Paste, and Message Log. G-Ware also provides Gate Views and
Meters so you can quickly monitor or troubleshoot your system.This chapter
describes how to use these utility programs and monitoring views in G-Ware.
Utilities
Signal Generator
Figure 5.1. Signal Generator Button
The Signal Generator window allows you to generate test audio signals to check
signal paths, gain settings, etc.The Signal Generator can generate pink noise, white
noise, and tone.
The Signal Generator window can
also be opened by selecting Signal
Generator from the Tools menu.
•
Pink Noise. Pink noise is an audio test signal containing all the frequencies
in a given audio spectrum, with equal energy in each octave. Pink Noise is the
default signal.
•
•
White Noise. White noise is an audio test signal which is distributed evenly
throughout a given frequency range.
Tone. Selecting Tone activates the tone configuration portion of the window.
The tone is a sine wave with less than .03% distortion.
The test signals created by the signal generator are assigned to a particular input;
this allows you to verify the operation of the processor settings you have selected.
To use pink or white noise
1. Select the XAP 800 Unit and Input Channel you want to use.
2. Use the Amplitude control to select the amplitude (volume) of the signal you
want to use.The amplitude range is from -60 to +20dB. Default is 0dB.
3. Select Pink (default) or White.
4
Click Signal On to generate the noise signal on the selected input. Click
Signal On again to terminate the noise signal.
Figure 5.2. Signal Generator window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
68
To use tone
1. Select the XAP 800 Unit and Input Channel the signal will be generated on.
2. Select Tone.
3. Using the Frequency slider, select a specific tone frequency.You can also
enter the frequency in the box directly below the Frequency slider.
– or –
Use the Auto Sweep button to sweep a range of frequencies. Select the
Begin Frequency, the End Frequency, the Increment, and the Rate.
Auto Sweep provides the ability to move the frequency of the tone generator
from a low frequency to a high frequency at a specified rate. Click Auto Sweep
to begin the frequency sweep.The Frequency slide control and readout reflect
the progress of the Auto Sweep. Auto Sweep stops at the last frequency in the
sweep range upon completion of the sweep. Or you can click the button at any
time to stop the sweep. Sweep range is 20Hz—20kHz; increment range is
10Hz—20kHz, and the rate range is 10ms—2000ms. Default is 100ms.
Select Repeat if you want Auto Sweep to continue in cycles.
4. Click Signal On to generate the tone. Click Signal On again to terminate the
noise signal.
Document Compare Utility
The Document Compare Utility samples and compares configuration information
between two sites.These can exist as actual sites/units or as documents (site files)
that are saved to your computer. It shows you where differences are between the two
and allows you to copy and paste settings between them. Open the Compare Utility by
clicking on the Compare Utility toolbar button.
Figure 5.3. Compare Utility button
To compare site files
1. Click the Browse button at the right of the Site 1 Document Name.This
Figure 5.4.You can also open the Document
Compare Utility from the Start menu
opens the Open window.
2. Select the first site file you want to compare.To compare the settings in a
connected site, click on the G-Ware Connections tab and select the unit or site.
3. When you have made a selection, click Refresh to update the status of the
unit, site, or connection.Then click Open.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
69
Figure 5.5. Open window
4. Repeat steps 1–3 to select the second second unit, site, or file for
comparison.
When you click Open, G-Ware automatically compares information from the
selected items and displays a table of parameters which differ (note that the
actual differences are not displayed at this point).This process can take a
minute or two.
Figure 5.6. Document Compare Utility showing two XAP 800 sites.The items
listed in the Site 1 and Site 2 columns show where the differences are
5. To view the difference(s) between two sources on a single parameter, select
the row in the table you want to examine, then click Preview.This opens the
Print Preview window, which shows what the differences are.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
70
Figure 5.7. Print Preview window
6. To print the report, click Print (you can also click Print in the Compare
Utility window to print the report).The other buttons in this window allow
you to tailor the view of the report and browse sequentially through each
page.
7. When you finish viewing or printing the report, close the Print Preview
window to return to the Document Compare Utility.
Copying settings
When two sites are compared, the Copy to Site, Paste, and Copy buttons at the
bottom of the window become selectable.
Print the comparison for a
detailed list of differences
✍
between the two sites.
Figure 5.8. Document Compare window
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
71
In the window shown in Figure 5.9, clicking the Site 1 button transfers the
selected settings from a line selected in the Site 2 column to the corresponding line
in the Site 1 column.The Copy button copies the settings of the Site/Line above it,
allowing you to paste (with the Paste button) settings to another site, unit, or even
to a particular G-Ware parameter, such as an input.
The remaining buttons in the Document Compare window do the following:
•
•
•
•
Refresh button updates the connection status to site(s) or unit(s).
Select All selects everything in the Site 1/Site 2 table.
Select None deselects anything highlighted in the table.
Click Close to exit the Document Compare Utility.
Print Reports
The Print Reports utility allows you to print a variety of configuration reports.To
open the Print Reports utility, select Print from the File menu.
Figure 5.9. Print Reports window
Select the item(s) you want to print, then click Print Preview to view a
preview of the report or Print to print the report(s). For example, you could select
Inputs 1–8 Report to print a copy of the settings you’ve established for Inputs 1–8.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
72
Make a note of the baud
rate selected in the Site
GFirm Firmware Utility
✍
To make it easy to upgrade your unit when new firmware enhancements are released,
G-Ware features a built-in firmware upgrade utility. Before upgrading firmware, save
a copy of your site files and verify that the flow control setting on the unit (RS-
232 menu on front panel LCD) is enabled. Also, make sure flow control is set to
Hardware in the G-Ware (Site Properties).
Properties
window
before opening the G-Ware
Firmware Utility.
To upgrade firmware
1. Connect the unit to the PC using a straight-through 9-pin serial cable.
2. Open the G-Ware Firmware Utility by clicking on the GFirm toolbar button.
Figure 5.10. GFirm button
If the GFirm toolbar
button is not on the
✍
G-Ware toolbar, you need
to install the current G-Ware
release. You can download G-Ware
from the ClearOne web site at
www.clearone.com.
Figure 5.11. G-Ware Firmware Utility
3. Click Browse to access a list of available firmware updates. Select the file
that matches the type of unit you are upgrading and click Open.
Figure 5.12. Available firmware files
4. The selected firmware file will self verify and display the message Verified,
OK. If the file information matches your unit and the file is verified, click
Next to advance to the Communications tab.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
73
5. Select the PC COM port you are using for the upgrade. Select the Baud
Rate that matches the baud rate in the Site Properties window.
Figure 5.13. Selecting baud rate
6. Click Next. If the upgrade requires you to save your site files, a warning
message will display.You will need to exit the G-Ware Firmware Utility, sync
to the units with G-Ware, and save the site file(s) if you have not done so
already. Click Yes, Continue to begin firmware upload.
7. The Progress tab displays the status of the firmware upgrade. Do not
interrupt the procedure.The process begins by erasing flash sectors and then
uploading the firmware file.
8
If the process fails, do not use the Start Over button. Close GFirm instead
and verify you are using a 9-pin straight-through serial cable and that baud
rate and flow control are configured properly. Restart GFirm and return to
step one of this procedure.
9. When the upgrade is complete, the Finished tab appears. Check the front
panel of unit and verify the proper firmware version for your unit is now
displayed. If you have no more units to upgrade, you can now close the
GFirm program.
If updating multiple units, move the RS-232 connection to the next unit and
click Start Over to continue.
10. After upgrading the firmware on all units, restore expansion bus connections.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Utilities
74
G-Ware Switcher
G-Ware Switcher allows you to alternate between different G-Ware software versions
that are installed on the same PC.
If you want to reinstall
previous versions, you
must install them in
✍
For example, if you need to upgrade the firmware on your ClearOne unit(s), G-
Ware Switcher allows you to easily switch to an earlier version of G-Ware (such as
3.5), save the site files, and then switch to a later version (4.5) to upgrade the
firmware.
different directories or G-Ware
Switcher will not work properly.
Prior to the 4.5 release, the older version of G-Ware had to be removed before
the new version could be installed.
Before using G-Ware Switcher
1. Load G-Ware 3.5 in a unique directory (path), as shown in Figure 5.14. Do
not select “Add Icon to Desktop” when you are asked if you want to do so
during the installation process.
Figure 5.14. Creating a
directory for G-Ware 3.5
2. Load G-Ware 4.5 in a unique directory (path), as shown in Figure 5.15. Do
not select “Add Icon to Desktop” when you are asked if you want to do so
during the installation process.
You are now ready to use G-Ware Switcher.
To use G-Ware Switcher
1. Launch G-Ware Switcher from the Windows Start menu by selecting
Programs, ClearOne G-Ware, and then G-Ware Switcher.
Figure 5.15. Creating a
directory for G-Ware 4.5
The G-Ware Switcher Utility Window opens. G-Ware Switcher automatically
searches the PC for G-Ware software versions and displays them in the
window.
Figure 5.16. G-Ware Switcher
2. Select the G-Ware version you want to use.
3. If the selected G-Ware version is active (if Yes appears in the Active column
for the version you want to run), click Run to launch it.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Monitoring Views
75
If the selected G-Ware version is not active, click Re-Register/Make
Shortcuts to re-register the version so it becomes active.Then click Run to
launch it.
If you have installed a version of G-Ware that isn’t displayed in the G-Ware
Switcher window, click Refresh. G-Ware Switcher will locate and display the
version.
Copy and paste settings
In most areas of G-Ware software, right-clicking the mouse opens a shortcut menu.
The options on this menu change depending on which window you are in.
The version shown at right allows you to copy and paste unit settings and sites,
as well as add or remove units from a site. For example, to copy unit settings to
another unit, place the cursor in the blue area of the Flow Screen, then right-click
to open the shortcut menu. Select Copy Unit. Next, open (add) another unit, then
right-click in the Flow Screen of the second unit to open the shortcut menu. Click
Paste Unit.This copies the properties of the first unit to the second one.
Figure 5.17. Shortcut menu
Message Log
The Message Log automatically displays messages indicating successful or
unsuccessful site connection and all errors.To open the Message Log, click the
Message Log toolbar button or select Message Log from the Tools menu.
Figure 5.18.
Message Log button
Figure 5.19. Message Log window
Monitoring Views
Gate View
The Gating button opens the Gate View window, which allows you to view gating
activity at each mic input on each unit in your site.
Figure 5.20.
Gating button
Select Enabled to observe unit gating information. Note that the window
shows gating activity only for units which have been added to G-Ware.The gate
indicator for each input is dark green in the gate-off condition and light green if
the input is gated on. Click Close to save the settings and exit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Operation ~ Monitoring Views
76
Figure 5.21. Gate View window
Meter Views
The Meter Views window allows you to monitor the level of any input, output, or
processing signal of the XAP 800.You can monitor the same parameter on multiple
inputs (or outputs or processing channels) for comparison or you can monitor an
entire signal flow from input to output. Click the Meters button on the G-Ware
toolbar to open this window.
Figure 5.22.
Meters button
Figure 5.23. Meter Views window
To configure Meter Views
1. Select the unit number, meter type, and channel you want to use. Note
that you can configure the meters such that you can monitor the same input
signal as it makes its way through various stages in the XAP 800.
2. Enable the meter by clicking the adjacent Enabled box.
3. When you have finished making changes, click Close to exit the window.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
CHAPTER 6: Control
There are many ways to control your XAP 800 and other networked units.This
chapter explains how to set up control for Control/Status A port using GPIO Builder,
XAP IR Remote and ClearOne Control Panel using Remote Builder and RS-232 port.
GPIO Builder
Control/Status A
GPIO stands for general-purpose input/output.The GPIO Builder is used to establish
the pin assignments for the 16 user definable pins on Control/Status Port A.These
pins provide control via contact closure and status via open collector functions in the
unit. Note that the pins numbered in blue are command pins; the pins numbered in
green are status pins.The default pin assignments are listed on page 88.You can
open GPIO Builder from the Flow Screen or the G-Ware toolbar.
To program control/status pins
If you want to create pin
assignments specific to a
preset, you will need to
open the GPIO Builder from the
Preset Configuration pane (see
page 57) and select Use in Preset.
1. Select the Control/Status A pin you want to configure.
✍
The current (default) pin assignment is displayed in the Active
(Low)/Inactive (High) Command box.
GPIO commands can be
configured only for the
✍
local XAP 800 unit.
Figure 6.1. GPIO Builder Window
2. Select the Device Type and ID from their respective lists.
3. Select the Command from the Command list. When you select a command,
a description of it appears in the Command Description box.
4. Select the command parameters from the argument lists.The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
5. Click Apply to apply the changes you have made to the selected pin. Or, click
Clear to clear any programming for the pin.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ Remote Builder
78
Remote Builder
The Remote Builder window is used to configure optional XAP IR Remotes and
ClearOne Volume and Select Control Panels.These control devices are connected to
Remote Panel A or Remote Panel B—the RS-485 connectors. If you want to create
custom control assignments for presets, open the Remote Builder from the Preset
Configuration pane and select the Use in Preset option.
XAP IR Remote
The XAP IR Remote provides remote control of volume, mute, speed dial, and dialing
for a XAP system.You can connect up to two XAP IR Remote Controls—one to
each RS-485 port. See the XAP IR Remote user manual for more information.The
XAP IR Remote has five programmable buttons and one programmable LED.You
can customize your XAP IR Remote using the Remote Builder. To open the Remote
Builder, click the Remote Builder button on the Flow Screen (or the button in the
G-Ware toolbar).
Figure 6.2. Remote Builder
button on Flow Screen
Figure 6.3. Remote
Builder toolbar button
If you want to program
different button assign-
✍
ments for use in a preset,
you will need to open the Remote
Builder from the Preset
Configuration pane (see page 57)
and select Use in Preset.
Figure 6.4. Remote Builder
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ Remote Builder
79
Up to five control panels
and one IR remote can be
To program the XAP IR Remote
✍
1. Select an ID number for the remote from the Select Remote ID list.
connected to each of the
RS-485 ports. In addition to
selecting the ID number in the
software, you will also need to use
the DIP switches on the IR
receiver to assign the Device ID.
See the XAP IR Remote manual
for more information.
2. Click Change Name to create a more descriptive name for the remote which
is displayed in addition to the remote number (limit 20 characters).
3. Select IR Remote (default) from the Select Remote Type list.
4. In the Telephone Interface section, select the Device Type and ID of the unit
(XAP 400 or XAP TH2) that you want the XAP IR remote to use when
making and receiving calls.The default settings are ** which will select any
telco device found on the network. If you have multiple telco devices in your
network, you must specify which unit will be used to make and receive calls.
5. Select the button or LED you want to program from the Select
Button/LED list.You can also select the button or LED by clicking directly
on the picture of the remote. (Selectable buttons are colored white.)
6. Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
7. Select the Device Type, ID, and Command from their respective lists. When
you select a command, a description of it appears in the Command
Description box.
8. Select the command parameters from the argument lists.The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
9. Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear any programming.
ClearOne Control Panels
ClearOne Control Panels are convenient wall panels which provide control over the
XAP 800 audio conferencing system.There are two Control Panel models:Volume
and Select.You can connect up to six Control Panels in daisy chain fashion to each
RS-485 port. See Appendix C for more information.The Control Panel buttons are
programmed using the Remote Builder.You can open the Remote Builder using the
Remote Builder button on the Flow Screen or the Remote Builder button on the
G-Ware toolbar.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ Remote Builder
80
Each Control Panel
button can be
programmed to respond
To program the Volume panel
✍
1. Select an ID number for the remote from the Select Remote ID list.
like a momentary or latching
button. A command can be
programmed to activate or
deactivate a particular function.
2. Click Change Name to create a more descriptive name (limit 20
characters) for the remote which is displayed in addition to the remote
number in the Select Remote ID list.The name is also updated on the
graphic label.
Up to six control panels
(or five control panels and
✍
one IR remote) can be
connected to each of the RS-485
ports. In addition to selecting the
ID number in the software, you will
also need to use the DIP switches
on the control panel to assign the
Device ID. See Appendix C: Control
Panel for more information.
Figure 6.5.Volume Panel selected in the Remote Builder
3. From the Remote Type list, select Volume.The Control Panel graphic will
change to match your selection.
4. Select the button or LED you want to program from the Button/LED
Selection list.You can also select the button or LED by clicking directly on
the picture of the Volume panel.
The default numbers on the left of the Volume panel LEDs represent gain
levels in decibels.To change a level, click on the LED and then select the
level from the Gain list at the bottom of the window.You can also set the
upper and lower limits of gain on LEDs L2 and L8 and then click Auto
Scale, which automatically assigns values to LEDs L3-L7 on a distributed
scale.
If you want to program
different button assign-
✍
ments for use in a preset,
you will need to open the Remote
Builder
from
the
Preset
Configuration pane (see page 57)
and select Use in Preset.
5. Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ Remote Builder
81
6. Select the Device Type, ID, and Command from their respective lists. When
you select a command, a description of it appears in the Command
Description box.
7. Select the command parameters from the argument lists.The parameters
that are available depend on the command selected. When you select an
argument, a description of it appears in the Argument Description box.
8. Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear programming.
If you want to program
different button assign-
ments for use in a preset,
To program the Select panel
✍
1. Select an ID number for the remote from the Select Remote ID list.
you will need to open the Remote
2. Click Change Name to create a more descriptive name (limit 20
characters) for the remote which is displayed in addition to the remote
number in the Select Remote ID list.The name is also updated on the
graphic label.
Builder
from
the
Preset
Configuration pane (see page 57)
and select Use in Preset.
Figure 6.6. Select Panel selected in the Remote Builder
3. From the Remote Type list, select Select.The Control Panel graphic will
change to match you selection.
4. Select the button or LED you want to program from the Button/LED
Selection list.You can also select the button or LED by clicking directly on
the picture of the Select panel.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ RS-232 Port
82
5. Click the Active Command or Inactive Command button to set the
command for operation when the button is active or inactive.
6. Select the Device Type, ID, and Command from their respective lists. When
you select a command, a description of it appears in the Command
Description box.
7. Select the command settings from the argument lists.The options that are
available depend on the command selected. When you select an argument, a
description of it appears in the Argument Description box.
8. Click the Apply button to apply the command to the selected Active or
Inactive command button. Or, click Clear to clear programming.
RS-232 Port
Remote Modem Access
You can access the unit remotely through a modem connected to the serial port.To
enable this feature, configure the port for modem mode.
When in modem mode, the serial port will send an initialization string to the
modem upon entering the mode or upon power-up of the unit.You program the
initialization string in Site Properties window in G-Ware.Typical configurations you
set with the initialization string include setting a fixed baud rate for the unit and
setting up auto-answer parameters.
The modem password is
created in the Unit
Properties window (see
You must enter a password before you can control the system this way.The
default password is blank (a carriage return).You can change it to any
combination of letters and/or numbers up to 12 characters. It is not case-sensitive.
✍
page 26) or by using the MPASS
serial command (see page 117).
When you establish a valid serial connection with the unit in modem mode, the
unit will wait for a carriage return. When you have entered a carriage return, the
system will prompt you to enter the password. If there is no activity for five
minutes on the serial port while in modem mode, the unit will re-prompt for the
password.
Serial commands
Serial commands can be passed through the XAP 800 RS-232 port using Hyper
Terminal, touch panels, or other compatible remote control devices.To learn more
about serial commands, see Appendix E.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Control ~ RS-232 Port
83
Command strings
By creating command strings, you can use your XAP 800 to control equipment such
as lighting, projectors, and room dividers as well as other ClearOne products. A
command string is passed to the connected device via the XAP 800’s RS-232 port.
You can create up to eight customized serial command strings (limit 80 characters
each) in the Command Strings window.To open the Command Strings window, click
the Command Strings toolbar button.
Figure 6.7. Command
Strings toolbar button
Figure 6.8. Command Strings window
To create a command string
Special characters
\a = alert
•
Type the serial command string (limit 80 characters) in one of the eight
locations.The command string will support special characters. See list at
right.
\b = backspace
\f = formfeed
\n = new line
\r = carriage return
\t = horizontal tab
\v = vertical tab
\\ = backslash
To run a command string
•
Use any external control device (e.g. Control Panel, GPIO control) to run the
STRING serial command.
– or –
•
Incorporate the STRING command into a macro which can be run from
G-Ware, the front panel, or any external control device.
For information on creating macros, see page 63. For information on GPIO builder,
see page 77. For information on Control Panels, see page 79.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
84
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
APPENDICES
Appendix A: Specifications
Dimensions (LxDxH)
17.25" x 10.25" x 1.75"
43.8 x 26 x 4.5 cm
+5VDC pins (2) (300mA over-current
protected)
Frequency Response: 20Hz to 20kHz
1dB
Noise (EIN): -126dBu, 20kHz BW,
max gain, Rs=150
Remote Panels A/B
4-pin push-on terminal block
RS-485 Proprietary Protocol
Category five twisted-pair cable
1 pair data, 1 pair power and ground
+15VDC (300mA over-current
protected)
Weight
7 lb/3.2 kg dry
12 lb/5.5 kg shipping
THD+N: <0.02%
SNR: 80dB re 0dBu, (A-weighted)
Dynamic Range: 100dB (A-weighted)
Crosstalk <-91dB re 20dBu @ 20kHz
channel to channel
Operating Temperature
32–100° F/0–38° C
Approvals
FCC, CSA, IC, CE, NOM, ACA, SABS,
JATE
Humidity
15% to 80%, non-condensing
Mic/Line Inputs 1-8
Push-on terminal block, balanced,
bridging
Power Input Range
Auto-adjusting
Impedance: 5k
Assignable Processing Blocks
Filters:
Nominal Level: adjustable -55dBu,
-25dBu, 0dBu
100–240VAC; 50/60Hz
All pass
Maximum Level: -35dBu, -5dBu,
+20dBu
Low pass
Power Consumption
30W typical
High pass
Echo Cancellation: 130ms tail time
(works with 12dB of room gain)
Noise Cancellation: 6–15dB attenuation
Phantom Power: 24V, selectable
Low shelving
High shelving
Parametric EQ
Notch
Expansion Bus In/Out
Proprietary Network
RJ-45 (2), 115.2kbps, 110k
impedance
CD Horn
Line Inputs 9-12
Push-on terminal block, balanced,
bridging
Category five twisted-pair cable
80’ (24 meters) maximum cable length
between any two XAP 800s,
XAP 400s, or PSR1212s
Crossovers
Bessel
Butterworth
Linkwitz-Riley
Compressor
Delay adjustable up to 500ms
Impedance: >10k
Nominal Level: 0dBu
Maximum Level: 20dBu
RS-232
DB-9 female
Outputs 1-12
Push-on terminal block, balanced
Impedance: 50
9,600/19,200/38,400 (default)/57,600
baud rate; 8 bits, 1 stop, no parity
Hardware flow control on (default)/off
Matrix Mixing Parameters
32x32 matrix
12 analog in/out
Nominal Level: 0dBu
Maximum Level: 20dBu
12 Expansion Bus in/out
8 assignable processing blocks in/out
Control/Status
DB25 female A/B (2)
Audio Performance
Inputs A/B: active low (pull to ground)
Outputs A/B: open collector, 40VDC
max, 40mA each
Auto Mixer Parameters
Number of Open Microphones (NOM)
PA Adaptive Mode
Conditions: Unless otherwise specified,
all measurements are performed with a
22Hz to 22kHz BW limit (no weighting)
First Mic Priority Mode
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix A: Specifications
86
Last Mic Mode
Echo Cancellation on/off
Auto Gate/Manual gate
Maximum # of Mics Mode
Ambient Level
Noise Cancellation on/off
Filters
Adaptive Ambient on/off
Set-up Software
G-Ware
Gate Threshold Adjust
Off Attenuation Adjust
Hold Time
All Pass
Low Pass
High Pass
Decay Rate
Notch
PEQ
Microphone Input Configuration
Input Gain Adjust
Mute on/off
Chairman Override on/off
AGC on/off
Mic or Line Level
Phantom Power on/off
Speech Leveler on/off
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix B: Pinouts
Appendix B: Pinouts
87
5
1
RS-232 COM DCE port pinout (female)
6
9
Pin Number
Control
Pin Number
Control
Figure B.1. RS-232 connector
1
2
3
4
5
DCD
6
7
8
9
DSR
TXD
CTS
ClearOne recommends that
all nine pins be connected to
avoid communication errors.
RXD
DTR
RTS
No connection
!
Ground
DB-9
Male
DB-25
DB-9
DB-9
Male
Female
Female
Pin 2
Pin 1
Pin 1
Pin 2
Pin 3
TXD (Pin 2)
TXD (Pin 2)
Pin 3
Pin 5
RXD (Pin 3)
Pin 4
RXD (Pin 3)
DTR (Pin 4)
GND (Pin 5)
Pin 7
GND (Pin 5)
PC
XAP 800
XAP 800
Modem
Pin 6
Pin 6
CTS (Pin 7)
RTS (Pin 8)
CTS (Pin 7)
RTS (Pin 8)
Pin 9
Pin 9
Figure B.2. XAP 800 to PC RS-232 connections
Figure B.3. XAP 800 to Modem RS-232 Connections
DB-9
Phoenix
DB-25
DB-9
Male
Female
Connectors
Female
RX2 (White)
TX2 (Red)
TXD (Pin 2)
RXD (Pin 3)
GND (Pin 5)
TXD (Pin 2)
RXD (Pin 3)
RTS (Pin 7)
TXD (Pin 2)
RXD (Pin 3)
GND (Pin 5)
GND (Black)
AMX
XAP 800
AMX
Modem
DTR (Pin 4)
CTS (Pin 4)
GND (Pin 5)
GND (Pin 6)
CTS (Pin 7)
RTS (Pin 8)
RTS2 (Green)
CTS2 (Blue)
CTS (Pin 7)
RTS (Pin 8)
RTS (Pin 20)
Figure B.4. XAP 800 to AMX RS-232 Connections
Figure B.5. Modem to AMX RS-232 Connections
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix B: Pinouts
88
Control/Status connectors
The Control/Status connections are provided on two DB-25 connectors.These
connectors are labeled Control/Status A and Control/Status B and contain different
types of pins.The inputs on these connectors are internally pulled high and are
activated by connecting the pin to ground.The outputs are open collectors, which are
open when inactive and grounded when active.This allows the XAP 800 to control
and be controlled by a wide variety of external devices, including relays, lamps,
switches, and other equipment. Control pins on Control/Status A are momentary
while control pins on Control/Status B are latching.
Figure B.6. Control/Status Ports A, B
Control/Status A Port Pinout (female)
Pin
Definable
Type
Default Description
The first 16 pins on the
Control/Status Port A are
can be programmed using
G-Ware software.
1
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Control
Lock front panel toggle
Status of front panel lock
Mute all mics toggle
✍
2
Status
3
Control
4
Status
Status of mute all mics
Mute Output 9 toggle
5
C
S
C
S
C
S
C
S
C
S
C
6
Status of Output 9 mute
Mute Output 10 toggle
Status of Output 10 mute
Mute Output 11 toggle
Status of Output 11 mute
Mute Output 12 toggle
Status of Output 12 mute
Volume Up D Output 1 (1dB)
Not programmed
7
8
9
10
11
12
13
14
15
(1dB)
16
17
18
19
20
21
22
23
24
25
Volume Down D Output 1
Yes
No
No
No
No
No
No
No
No
No
S
Not programmed
Mic #1 Gate Status
Mic #2 Gate Status
Mic #3 Gate Status
Mic #4 Gate Status
Mic #5 Gate Status
Mic #6 Gate Status
Mic #7 Gate Status
Mic #8 Gate Status
Ground
S
S
S
S
S
S
S
S
Ground
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix B: Pinouts
Control/Status B port pinout
89
Pin
Definable*
Type
Default Description
1
No
C
S
C
S
C
S
C
S
C
S
C
S
C
S
C
S
C
S
C
S
Preset select bit
2
No
Preset select status for Pin 1
Preset select bit
3
No
4
No
Preset select status for Pin 3
Preset select bit
5
No
6
No
Preset select status for Pin 5
Preset select bit
7
No
8
No
Preset select status for Pin 7
Preset select bit
9
No
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
No
Preset select status for Pin 9
Preset select bit
No
No
Preset select status for Pin 11
Preset select bit
No
No
Preset select status for Pin 13
Preset select bit
No
No
Preset select status for Pin 15
Preset select bit
No
No
Preset select status for Pin 17
Preset select bit
No
No
Preset select status for Pin 19
No connection
No connection
No
No
No
-
-
-
+5VDC, 300mA
+5VDC, 300mA
Ground
Control/Status A and B: DB25 female
Inputs A and B: active low (pull to ground)
Outputs A and B: Open collector, 40V max, 40mA each
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix B: Pinouts
90
RS-485 Remote Panel A and B connectors
4
3
2
1
4
3
2
1
Pin
Description
Figure B.7. RS-485 Remote Control Ports
1
+15VDC, 300mA (over-current protected)
Set connector pinout
Pin
Description
Pin
Description
1
2
3
To pin 6 of SET RJ-11C
To pin 5 of SET
Ring
4
5
6
Tip
To pin 2 of LINE
To pin 1 of LINE RJ-11C
Line connector pinout
Pin
Description
Pin
Description
1
2
3
To pin 6 of LINE RJ-11C
To pin 5 of LINE
Tip
4
5
6
Ring
To pin 2 of SET
To pin 1 of SET RJ-11C
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix C: Control Panel
91
Appendix C: Control Panel
This equipment must be
installed according to
applicable local electrical
The Volume Control Panel and Select Control Panel connect to either the Remote
Panel A or B connector of the PSR1212, XAP 800, or XAP 400 and works by
triggering the execution of programmed commands from the XAP/PSR unit. Each
button on the control panel is programmable to execute a single command or a
series of commands. Button function is programmed using G-Ware software (see the
XAP or PSR user manual). Each Control Panel fits inside a standard electrical wall
box and must be installed according to local electrical codes.
!
codes.
O N
1
Connecting the Control Panel
2
3
4
5
6
7
8
1. Ensure you received a facia plate; a Control Panel assembly with mounting
bracket and two RS-485 Phoenix four-pin connectors; two connector
terminator blocks; a faceplate; two flat HD screws; two pan-head screws; and
an electrical wall box (shown in Figures C.5 and C.6). If any parts are
missing, please contact ClearOne.
Figure C.1. DIP switches
2. Using DIP switches 1–4, assign a unique ID to the Control Panel. Refer to
Figure C.2 for proper DIP switch settings. If you set an invalid address, all LEDs
on the Control Panel will illuminate.
3. Set DIP switch 8 to the on position if you are using just one Control Panel. If you
have more than one Control Panel daisy-chained to the same Remote Panel
connector, set only the last Control Panel’s DIP switch 8 to on. Switches 5-7 are
nonfunctional.
4. Turn off the XAP/PSR unit (unplug the unit).
Figure C.2. DIP switch settings
5. Wire each end of a Cat. 5 cable to a connector terminator block. Use one
twisted wire pair for the center - and + connections (pins 2 and 3) and the
other twisted pair for the ground and +15V connections (pins 1 and 4). Failure
to correctly wire the connector can result in damage to the unit.
Figure C.3.Wiring the Control Panels
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix C: Control Panel
92
6. Connect one connector terminator block to the Remote Panel on the
XAP/PSR unit. Route the other end of the cable through the back of the
electrical wall box and connect the terminator block to the Control Panel.
Control Panel Assembly
Dimensions (both
versions): 1.8ý/4.6cm W x
✍
4.125ý /10.5cm L (not including
faceplate or electrical box).
7. To use a second Control Panel, connect it to the unused Remote Panel
connector on the XAP/PSR unit or the unused connector on the first
Control Panel.You can daisy-chain up to six Control Panels to each Remote
Panel connector.Total cable run depends on the number of Control Panels
used.The distance information in the table at left is based on Cat. 5 cable
with a nominal resistance of 27 per 1,000 feet (305 meters). All distances
refer to total cable runs from a single Remote Panel connector. For
information about extending beyond 800 feet (244 meters) total with six
Control Panels, call Technical Support at 1-800-283-5936.
# of Control Panels
Maximum Distance*
3,000 ft/914 meters
2,500 ft/762 meters
1,600 ft/488 meters
1,200 ft/366 meters
1,000 ft/305 meters
800 ft/244 meters
1
2
3
4
5
6
Figure C.4. Control panel distance chart
8. As shown in Figures C.5 and C.6, use the supplied pan-head screws to install
the Control Panel PCB assembly to the electrical wall box.
9. To install the facia plate, position it over the conductive rubber switch pads
on the PCB assembly, as shown in Figures C.5 and C.6.
10. Mount the faceplate over the rubber switch pads, using the two flat HD
screws.
460-155-002 WALL ENCLOSURE 2.25 X 3.25 INCHES
681-010-616 SCREWS (2) 6-32 X 1 INCH PPH
740-155-050 FACIA PLATE
460-155-001 FACEPLATE
FLAT HEAD SCREWS (2)
INCLUDED WITH FACEPLATE
915-155-050 ASSEMBLY, SELECT CONTROL PANEL INCLUDES:
820-155-050 CONTROL PANEL PCB ASSEMBLY W/TWO FOUR-PIN PHOENIX CONNECTORS
740-155-052 CONTROL PANEL MOUNTING BRACKET
625-100-006 ELASTOMER CONDUCTIVE RUBBER SWITCH PADS (4 EACH)
673-016-104
CONN TERM BLOCK/
F EURO 4 P
(2 EACH)
SELECT CONTROL PANEL 910-155-050
Figure C.5. Select Control Panel Assembly
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix D: Accessories
93
460-155-002 WALL ENCLOSURE 2.25 X 3.25
915-155-051 ASSEMBLY, VOLUME CONTROL PANEL INCLUDES:
820-155-051 VOLUME CONTROL PANEL PCB ASSEMBLY W/TWO FOUR-PIN PHOENIX CONNECTORS
740-155-052 CONTROL PANEL MOUNTING BRACKET
625-100-006 ELASTOMER CONDUCTIVE RUBBER SWITCH PADS (3 EACH)
740-155-051 FACIA PLATE
460-155-001 FACEPLATE
FLAT HEAD SCREWS (2)
INCLUDED WITH FACEPLATE
681-010-616 SCREWS
(2) 6-32 X 1 INCH PPH
673-016-104
CONN TERM BLOCK/
F EURO 4 P
(2 EACH)
VOLUME CONTROL PANEL 910-155-051
Figure C.6.Volume Control Panel Assembly
This equipment complies with the requirements of the European guidelines:
89/336/EEC “Electromagnetic Compatibility” and 93/68/EEC “Electrical
operating material for use within specific voltage limits.”
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may
cause undesired operation.
Appendix D: Accessories
Accessory
ClearOne Part Number
910-103-160 (with cable)
910-103-161 (with cable)
Tabletop Omni Microphone
Tabletop Uni Microphone
Button Omni Microphone
Button Uni Microphone
Delta Microphone
910-103-162 (black button)/910-103-163 (white button)
910-103-164 (black button)/910-103-165 (white button)
910-103-340
Acc. Kit, Side Trim
860-150-002
Wall Mount Speaker
Select Control Panel
Volume Control Panel
XAP IR Remote
910-103-010
910-155-050
910-155-051
910-170-150
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
94
Appendix E: Serial Commands
The XAP 800 accepts serial commands through the serial port or the expansion bus.The commands in this manual
pertain only to the XAP 800. RS-232 serial port protocol is 9,600, 19,200, 38,400 (default), or 57,600 baud; 8
bits, 1 stop bit, no parity.
Conventions
The following typographic conventions are used in this document to describe the different serial commands. Use the
Command structure section and the examples as a guide when creating your serial commands.
Convention
Description
<X>
Parameters enclosed in < > indicate a mandatory parameter.
[X]
Parameters enclosed in [ ] indicate an optional parameter.
1-8
Parameters separated by a - indicate a range between the values.
Parameters separated by a , indicate a list of available values.
4,7,9
EREF
DEVICE
Words in uppercase bold indicate command text.
Indicates the device type and device number on the expansion bus network. It is composed of a
device type character and a device number.The device type for the XAP 800 is always 5 and the
device ID will always be 0–7, or * (to select all 800 units).
Command structure
Commands can be either UPPER CASE or lower case. Also, extra spaces or tabs between arguments in text commands
are allowed. Return values are always in upper case. In order for a command to be recognized by the serial port, the
command must be terminated by a carriage return.
The structure of serial commands is as follows: #DEVICE COMMAND [X] [X]
#
indicates the start of a command line
DEVICE
COMMAND
[X] [X]
represents the device type and device number
is the command text
represents any additional options in the order that they appear in the command descriptions that
follow
Example
A command to disable automatic gain control for Mic 2 on a XAP 800 device “0” will have the command line:
#50 AGC 2 M 0. In this command line, 5=XAP 800, 0=unit 0, AGC=command, 2=channel, M=Mic Input group, 0=off
state. If a command calls for a “null” value, leave a blank in the command line. For example,“#50 AGC 2 M” will
return the current AGC state of Mic 2 on device 50.
Command responses will have a carriage return line feed. Example: #50 AGC 2 M O carriage return line feed.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
95
Groups and channels
If a channel has an alpha value of “*”, the command is to be applied to all channels. For example, a group value
of M and a channel value of * would mean that the command is to be applied to all channels of group M (mic
inputs).The following table shows the alpha representations for the different groups and the channels that are
available for each product.
Type and device IDs
Type ID
Unit type
Device ID range
4
5
6
7
PSR1212
XAP 800
XAP TH2
XAP 400
0–7
0–7
0–F
0–7
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
96
Meter type definitions
Serial command error codes
Error number
Text message
Explanation/Solution
1
2
3
Memory error
The box is out of internal memory. Power cycle the box.
A command was not found in the string.
No command found
Unknown command
response
A command was executed on a different device type that this box
cannot display.The command dictionary needs to be updated.
4
5
6
7
8
Not implemented
Argument error
Unknown command
Bad checksum
The command is not implemented.
The command had an argument that was out of range.
The command is unknown to this unit.
The binary command’s checksum is wrong.
Preset of macro invalid A preset or macro failed to program because it is too large or
because its comand list contained an invalid command.
10
Queue error
The internal command queue is full. Enable flow control and use
all five pins on the serial port.
11
12
Command too big
Unit is locked
The binary command is too large.
Unlock the unit with the proper password.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
97
XAP 800 Serial commands
Command
Function
Command
Function
AAMB
Selects/reports adapt ambient setting
Selects/reports acoustic echo canceller setting
Enable/disables AGC
LOCK
Selects/reports the state of the preset and
AEC
macro lock.When on, the lock prevents presets
and macros that have been flagged from being
altered in any way.
AGC
AGCSET
AMBLVL
BAUD
Selects/reports AGC settings on inputs
Selects/reports ambient level
LOCKPRST
LOCKPWD
Selects/reports whether the lock is applied to a
preset or macro. If a preset or macro has the
lock applied, it can only be changed if the unit
is unlocked with the password.
Selects/reports the baud rate of the serial port
Selects/reports compressor group setting
Selects/reports chairman override setting
Sets/reports compressor on audio processing
channel
CGROUP
CHAIRO
COMPRESS
Selects/reports the password for the
preset/macro lock.This can only be changed if
the unit is unlocked.
COMPSEL
Selects/reports compressor activity for
processor
LMO
LVL
Selects/reports Last Mic On mode
Reports in, out, or processor level
DECAY
DELAY
DELAYSEL
DFLTM
DID
Sets/reports decay rate
Sets/reports delay rate
LVLREPORT Selects/reports level status
Selects/reports processor channel delay
Sets/reports default meter
LVLRRATE
MACRO
Sets the level report rate for the unit
Executes macro or reports last macro
executed
Selects/reports device ID
DSPVER
FILTER
Reports DSP firmware version
Selects/reports input/processor channel filter
setting
MASTER
MAX
Reports the mode of the unit
Changes/reports max gain setting for in, out,
processor block
FILTSEL
FLOW
FMP
Enables/disables filters on input/processor
channel
MDMODE
MIN
Enables/disables the modem mode for the unit
Changes/reports minimum gain setting for in,
out, processor block
Selects/reports the flow control of the serial
port
MINIT
Sets/reports modem initialization string of
serial port
Sets/reports 1st Mic Priority for mic gating
group
MINMAX
MLINE
MMAX
MPASS
Changes/reports min and max gain from in,
out, processor block
FPP
Sets/reports current passcode setting
Changes/reports gain for in, out, or process.
Reports gate status of channels 1–8
Selects/reports hold time setting
Selects/reports gating mode setting
Selects/reports gating override setting
Selects/reports gate ratio setting
Selects/reports gate status report frequency
Selects/reports input gating group assignments
Selects/reports label of specified channel
Sets/reports status of front panel access
GAIN
Selects/reports coarse gain adjustments on
Inputs 1–8
GATE
GHOLD
GMODE
GOVER
GRATIO
GREPORT
GRPSEL
LABEL
LFP
Selects/reports max # of mics for each mic
group
Sets passcode setting when using modem
mode
MTRX
MTRXLVL
MUTE
NCD
Selects/reports matrix routing of an in. to out.
Selects/reports matrix level at the cross point
Sets/reports mute status
Selects/reports noise cancellation amount for
each mic channel
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
98
Command
Function
Command
Function
NCSEL
Selects/reports noise cancellation on/off for
each mic channel
REFSET
Selects/reports the output the reference channel
tracks
NLP
Selects/reports NLP for each mic channel
Selects/reports NOM setting on output
channels
SERECHO
SERMODE
Selects/reports the serial echo of the RS-232
Selects/reports the serial mode of the RS-232
NOM
SFTYMUTE Selects/reports the state of the safety mute.
When on, the safety mute holds all outputs in a
muted state.
OFFA
Selects/reports off attenuation mode for
Inputs 1–8
PAA
Selects PA adapt mode for specified input
Selects/reports phantom power setting
Executes preset or report last executed preset
SIGGEN
SIGTOUT
SLVL
Selects/reports signal generator activation
Sets the signal generator time out for the unit
Selects/reports mic auto level setting
Executes a string for the RS-232 port
Selects/reports the title screen inactivity time
out
PP
PRESET
PRGSTRING Sets/reports a programmed string
STRING
TOUT
RAMP
Start/stops the gain ramp for an input, output,
or assignable processing block
Selects/reports PA adapt mode for mic
outputs
REFSEL
UID
Reports unit ID (read only)
VER
Reports unit version (read only)
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
99
AAMB - Adaptive Ambient Mode
This command selects/reports the setting of adaptive ambient.
Command form: DEVICE AAMB <Channel> <Group> [Value] :
Argument details
Name
Device
AAMB
Channel
Group
Value
Description
0–7 or * to select all units
Command form
Range 1–8 (Selects input)
M (Selects mic group)
0 = Off, 1 = On, 2 = Toggle, Null to query in text
Example: #51 AAMB 2 1 On XAP 800 unit 1 (#51), adaptive ambient (AAMB
)
for mic channel 2 ( ) is set on ( ).
2
1
AEC - Acoustic Echo Canceller Enable/Disable
This command selects/reports the setting of acoustic echo canceller.
Command form: DEVICE AEC <Channel> [Value]
Argument details
Name
Device
AEC
Description
0–7 or * to select all units
Command form
Channel
Group
Value
Range 1–8 (selects input)
M (selects mic group)
0 = Off, 1 = On, 2 = Toggle, Null to query in text
Example: #50 AEC 1 0 On XAP 800 unit 0 (#50) the echo canceller (AEC) for
mic channel 1 ( ) is set to off ( ).
1
0
AGC - Automatic Gain Control
This command selects/reports the setting of automatic gain control.
Command form: DEVICE AGC <Channel> <Group> [Value]
Argument details
Name
Device
AGC
Description
0–7 or * to select all units
Command form
Channel
Group
Value
See Groups and Channels on page 97
1,3,7 (I,M,L)
0 = Off, 1 = On, 2 = Toggle, Null to query in text
Example: #54 AGC 1 M 0 On XAP 800 unit 4 (#54), the automatic gain control
AGC) on mic ( ) channel is set to off ( ).
(
M
1
0
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
100
AGCSET - Automatic Gain Control Adjust
This command selects/reports the settings of the AGC on the input channels.
Command form DEVICE AGCSET <Channel> <Group> [Threshold]
[Target] [Attack] [Gain]
Argument details
Name
Description
Units
Device
0–7 or * to select all units
Command form
AGCSET
Channel
Group
See Groups and Channels on page 97
1,3,7,(I,M,L)
Threshold
-50 to 0
dB
Null to query in text
-30 to 20
Target
Attack
Gain
dB
s
0.10–10.00 (select in .1s intervals)
0.00–18.00
dB
Example: #55 AGCSET 1 M -10 4 .5 18 On XAP 800 device 5 (#55) the
automatic gain control (AGCSET) for mic ( ) channel 1 ( ) is set to have a
dB rms, a response time of 500ms (.5), and a
M
1
threshold of -10dB rms, a target of
4
maximum gain of 18dB.
AMBLVL - Ambient Level Adjust
This command selects/reports the setting of the ambient level.
Command form: DEVICE AMBLVL <Channel> [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
AMBLVL
Channel
Value
Command form
Range 1–8 (selects input channel)
-80.0 to 0 (sets ambient level in dB), Null to return current level
Example: #53 AMBLVL 1 -30 On XAP 800 unit 3 (#53), the ambient level
AMBLVL) for mic input is set to -30dB.
(
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
101
BAUD - Baud Rate
This command selects/reports the baud rate of the serial port.
Command form: DEVICE BAUD [Value]
Argument details
Name
Device
BAUD
Value
Description
0–7 or * to select all units
Command form
9600, 19200, 38400, 57600
(Null to query in text)
Example: #56 BAUD 38400 On XAP 800 unit 6 (#56), the baud rate (BAUD
)
for the RS-232 port is set to 38,400 (38400).
CGROUP - Compressor Group Select
This command selects/reports the setting of the compressor group on each assignable
processing channel.
Command form: DEVICE CGROUP <Channel> [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
CGROUP
Channel
Value
Command form
range A–H (selects processing channel)
0 = none, 1 = compressor group 1, 2 = compressor group 2,
3 = compressor group 3, 4 = compressor group 4,
null to return the current mode
Example: #52 CGROUP A 2 On XAP 800 unit 2 (#52), the compression group
CGROUP) for processing channel is
(
A
2.
CHAIRO - Chairman Override Mode
This command selects/reports the setting of chairman override.
Command form: DEVICE CHAIRO <Channel> [Value]
Argument details
Name
Description
Device
CHAIRO
Channel
Value
0–7 or * to select all units
Command form
Range 1–4 (selects mic input)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #57 CHAIRO 3 1 On XAP 800 unit 7 (#57), chairman override
CHAIRO) for mic channel is set on ( ).
(
3
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
102
COMPRESS - Compressor Adjust
This command selects/reports the setting of the compressor on processing channels.
Command form DEVICE COMPRESS <Channel> [Threshold] [Ratio] [Attack]
[Release] [Gain]
Argument details
Name
Description
Units
Device
0–7 or * to select all units
Command form
COMPRESS
Channel
Threshold
Ratio
Range A–H (selects processing channel)
-30 to 20, Null to return current value
1 to 20
dB
Attack
0.00 to 100.00 (select in .5ms intervals)
100 to 2000 (select in 5ms intervals)
0.00 to 20.00
ms
ms
dB
Release
Gain
Example: #51 COMPRESS A 6 5 25 250 3 On XAP 800 unit 1 (#51), the
compression (COMPRESS) within processing channel is set to have a threshold
of dB, a ratio of 5:1 ( ), an attack time of 25ms, a release time of 250ms, and a
gain of dB.
A
6
5
3
COMPSEL - Compression Select
This command selects/reports the compressor activation of each assignable
processing channel.
Command form: DEVICE COMPSEL <Channel> [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
COMPSEL
Channel
Value
Command form
Range A–H (selects processing channel)
0 = Off, 1 = On, 2 = Toggle, Null returns current state
Example: #50 COMPSEL A 1 On XAP 800 unit 0 (#50), the compression
COMPSEL) within processing channel is set on ( ).
(
A
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
103
DECAY - Decay Adjust
This command selects/reports the setting of the decay rate for a specified input.
Command form: DEVICE DECAY <Channel> [Value]
Argument details
Name
Device
DECAY
Channel
Value
Description
0–7 or * to select all units
Command form
Range 1–8 (selects mic input)
1 = Slow, 2 = Medium, 3 = Fast, Null to return current state
Example: #53 DECAY 1 3 On XAP 800 unit 3 (#53), the decay rate (DECAY
)
for mic channel is set to fast ( ).
1
3
DELAY - Delay Adjust
This command selects/reports the delay time of each assignable processing channel.
Command form: DEVICE DELAY <Channel> [Value]
Argument details
Name
Device
DELAY
Channel
Value
Description
Units
0–7 or * to select all units
Command form
A–H (select processing channel)
0.00 to 500 (selects delay)
Null to return current state
ms
Example: #56 DELAY A 200 On XAP 800 unit 6 (#56) the delay (DELAY) for
processing channel is set to 200ms.
A
DELAYSEL - Delay Select
This command selects/reports the delay activation of an assignable processing
channel.
Command form: DEVICE DELAYSEL <Channel> [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
DELAYSEL
Channel
Value
A–H (select processing channel)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #54 DELAYSEL A 1 On XAP 800 unit 4 (#54) the delay
DELAYSEL) within processing channel is enabled ( ).
(
A
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
104
DFLTM - Default Meter
This command selects/reports the setting of the default meter.
Command form: DEVICE DFLTM [Channel] [Group] [Position]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
DFLTM
Channel
Group
1–12
I = Inputs, O = Outputs, M = Mic Inputs, L= Line Inputs
I, A, N, G, as applicable for group
(see Meter Type definitions, page 98)
Position
Example: #55 DFLTM 8 O A On XAP 800 unit 5 (#55), the default meter
DFLTM) is set to output ( after the gain adjustment ( ).
(
O
)
8
A
DID - Device ID
This command selects/reports the device ID.
Command form: DEVICE DID [Value]
Argument details
Name
Device
DID
Description
0–7 or * to select all units
Command form
Value
0–7 (select device ID)
Example: #57 DID 0 On XAP 800 unit 7 (#57), the device ID (DID) is set to
0.
DSPVER - DSP Version
This command reports the version of the DSP code in the unit. the version is a date
and time stamp.This command is read only.
Command form: DEVICE DSPVER [value]
Argument details
Name
Device
DSPVER
Value
Description
0–7 or * to select all units
Command form
Null
Example: #55 DSPVER The XAP 800 unit 5 (#55) will return the DSP version
DSPVER).
(
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
105
FILTER - Filter Adjust
This command selects/reports the setting of filters.
Command form: DEVICE FILTER <Channel> <Group> <Node> [Type]
[Frequency] [Gain] [Bandwidth]
Argument details
Name
Device
FILTER
Channel
Group
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 97
See Groups and Channels, page 97
1–4 (selects mic input filter)
1–15 (selects processing channel filter)
Description
Node
Name
Units
Type
0 = None, 1 = All Pass, 2 = Low Pass,
3 = High Pass, 4 = Low Shelving,
5 = High Shelving, 6 = Parametric Equalizer,
7 = CD Horn, 8 = Bessel Crossover,
9 = Butterworth Crossover,
10 = Linkwitz-Riley Crossover, 11 = Notch,
Null to return the current mode
0 for Null (Type 0)
Frequency
Gain
Hz
20 to 20,000 (Type 1–6, 8–11)
500 to 5,000 (Type 7)
Hz
Hz
dB
0 for Null (Type 0–3, 7, 11)
-15.00 to 15.00 (Type 4–6)
12, 18, 24 (Type 8–9)
dB per octave
dB per octave
dB per octave
12, 24 (Type 10)
-80 nonadjustable (Type 11)
0 to Null (Type 0–5, 7)
Bandwidth
.05–5.00 (Type 6, 11)
2 = low pass, 3 = high pass (Type 8–10)
Examples
#50 FILTER 1 M 3 2 200 On XAP 800 unit 0 (#50) the filter (FILTER) for mic
) channel , node is set as a low-pass filter ( ) at 200Hz.
(M
1
3
2
#51 FILTER B P 2 4 3000 -10 On XAP 800 unit 1 (#51) the filter (FILTER) for
processing ( ) channel , node , is set as a low shelving ( ) filter at 3000Hz and a
gain of -10dB.
P
B
2
4
#52 FILTER 3 M 2 6 5000 -15 1.00 On XAP 800 unit 2 (#52), the filter
FILTER) for mic ( ) channel , node , is set as a PEQ ( ) with a center
(
M
3
2
6
frequency of 5000Hz, a bandwidth of 1.00, and a gain of -15dB.
#53 FILTER B P 2 7 4000 On XAP 800 unit 3 (#53), the filter (FILTER) for
processing (P) channel
B
, node 2, is set as a CD Horn (7) at a frequency of 4000Hz.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
106
FILTSEL - Filter Select
This command turns on and off the filters on input and audio processing channels.
Command form: DEVICE FILTSEL <Channel> <Group> <Node> [Value]
Argument details
Name
Device
FILTSEL
Channel
Group
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 97
M = Mic Inputs, P = Processing Channels
1-4, or * for all (selects mic input filter)
1-15, or * for all (selects processing channel filter)
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Node
Value
Example: #54 FILTSEL B P 2 1 On XAP 800 unit 4 (#54), the filter
FILTSEL) on processing ( ) channel , node , is set to on ( ).
(
P
B
2
1
FLOW - Flow Control
This command selects/reports the flow control of the serial port on the unit.
Hardware flow control is implemented using DTR and DSR.
Command form: DEVICE FLOW [Value]
Argument details
Name
Device
FLOW
Value
Description
0–7 or * to select all units
Command form
0 = Off, 1 = On, 2 = Toggle, Null to return current state
Example: #56 FLOW 1 On XAP 800 unit 6 (#56), the flow control (FLOW) to
the RS-232 port is set to on ( ).
1
FMP - First Mic Priority Mode
This command selects/reports first Mic priority mode for a gating group.
Command form: DEVICE FMP <Channel> [Value]
Argument details
Name
Device
FMP
Description
0–7 or * to select all units
Command form
Channel
Value
1–4, A–D (selects gating group)
0 = Off, 1 = On, 2 = Toggle, Null returns the current mode
Example: #55 FMP A 1 On XAP 800 unit 5 (#55), the first mic priority mode
FMP) for gating group is set to on ( ).
(
A
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
107
FPP - Front Panel Passcode
This command sets and reports the current passcode setting for the unit. Each
character in the password represents a button on the front panel. See button
assignment table below.When the user is requested to unlock the front panel, they
must press the buttons in the sequence of the stored password.
Command form: DEVICE FPP <char1><char2><char3><char4><char5>
Button assignment
Value Button represented
1
2
3
4
5
Up arrow button
Enter button
ESC button
Down arrow button
Meter button
Argument details
Name
Device
FPP
Description
0–7 or * to select all units
Command form
Char 1–5
1–5 (see button assignments)
CLEAR will clear the passcode
Null will return current passcode
Example: #55 FPP 12345 On XAP 800 unit 5 (#55), the front panel passcode
FPP) is set to Up Arrow ( ), Enter ( ), Esc ( ), Down Arrow ( ), Meter ( ).
(
1
2
3
4
5
GAIN - Gain Adjustment
Values indicate entry
range only. Actual internal
This command changes or reports back the input gain for a channel.
Command form: DEVICE GAIN <Channel> <Group> [Value A/R]
✍
range of the gain stage is
from -65 to 20. Absolute values
will be limited to the internal gain
range and values below –65 will
mute the channel.
Argument details
Name
Device
GAIN
Description
0–7 or * to select all units
Command form
Channel
Group
See Groups and Channels, page 97
I = Inputs, O = Outputs, M = Mic Inputs,
P = Processing Channels, L = Line Inputs
-99 to 99 *, Null to return the current gain
A = Absolute, R = Relative, Null = Relative
Value
A/R
Example: #51 GAIN 4 O 12 A On XAP 800 unit 1 (#51), the GAIN for Output
is set to 12dB absolute ( ).
(O)
4
A
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
108
GATE - Gate Status
This command reports the gate status of mics.This command is read only.
Command form: DEVICE GATE
Argument details
Name
Device
GATE
Description
0–7 or * to select all units
Command form
The command will return the gate status of mic inputs 1–8 in hexadecimal.
Example:
If
Hex # returned
Hexadecimal Description
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mic 8 Mic 7 Mic 6 Mic 5 Mic 4 Mic 3 Mic 2 Mic 1
Mics 1 and 2 are gated on
Mics 1 and 3 are gated on
Mics 1, 4, and 7 are gated on
Mics 3–6 and 8 are gated on
0 3
0 5
4 9
B C
0
0
0
1
0
0
1
0
0
0
0
1
0
0
0
1
0
0
1
1
0
1
0
1
1
0
0
0
1
1
1
0
First digit
Second digit
GHOLD- Gate Hold Time Adjust
This command selects/reports the setting of hold time.
Command form: DEVICE GHOLD <Channel> [Value]
Argument details
Name
Device
GHOLD
Channel
Value
Description
Units
0–7 or * to select all units
Command form
See Groups and Channels, page 97
0.10-8.00
S
Null to return the current hold time
Example: #50 GHOLD 1 .3 On XAP 800 unit 0 (#50), the hold time (GHOLD
for mic channel is 300ms (.3).
)
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
109
GMODE - Gating Mode
This command selects/reports the setting of gating mode.
Command form: DEVICE GMODE <Channel> [Value]
Argument details
Name
Device
GMODE
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
1 = auto, 2 = manual on, 3 = manual off, Null= current mode
Example: #55 GMODE 1 2 On XAP 800 unit 5 (#55), mic channel
gating mode (GMODE) if manual on ( ).
1
is set to a
2
GOVER - Gating Override
This command selects/reports the setting of gating override.
Command form: DEVICE GOVER <Channel> [Value]
Argument details
Name
Device
GOVER
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = current mode
Example: #56 GOVER 1 0 On XAP 800 unit 6 (#56), the gating override
GOVER) on mic channel is set to off ( ).
(
1
0
GRATIO - Gate Ratio Adjust
This command selects/reports the setting of the gate ratio.
Command form: DEVICE GRATIO <Channel> [Value]
Argument details
Name
Device
GRATIO
Channel
Value
Description
Units
0–7 or * to select all units
Command form
1–8 (select mic input)
0 to 50
dB
Null to return current ratio
Example: #52 GRATIO 1 15 On XAP 800 unit 2 (#52), the gate ratio
GRATIO) for mic channel is set to 15dB.
(
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
110
Gate report sends a report
on every gate change. If
no mics are gated on, the
GREPORT - Gate Report
✍
This command selects/reports the gate status.
Command form: DEVICE GREPORT <Value>
report will be sent every 10
seconds.
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
GREPORT
Value
0 = Off, 1 = On, 2 = Toggle
Example: #53 GREPORT 1 On XAP 800 unit 3 (#53), the gate reporting
GREPORT) is set to on ( ).
(
1
GRPSEL - Gating Group Select
This command selects/reports which gating group each input is assigned.There can
only be one selection per input.
Command form: DEVICE GRPSEL <Channel> [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
GRPSEL
Channel
Value
1–8 (selects mic input)
1–4, A–D (selects gating group), Null to return current value
Example: #54 GRPSEL 1 A On XAP 800 unit 4 (#54), mic channel
1
is assigned
to gating group (GRPSEL
)
A.
LABEL - Label
This selects/reports the label of the specific channel identified in the unit.
Command form: DEVICE LABEL <Channel><Group>[In/Out] [String]
Argument details
Name
Device
LABEL
Channel
Group
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 97
I, O, M, G, P, L, E, U,W, S, C (see page 97)
In/Out
String
0 = Output, 1 = Input (For Expansion Bus groups only)
String of up to 20 characters representing the label text.
Null to query and CLEAR to clear the label
Example: #57 LABEL 1 M WIRELESS On XAP 800 unit 7 (#57), the label
LABEL) for mic ( ) channel is WIRELESS
(
M
1
.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
111
LFP - Lock Front Panel
This command sets and reports front panel access for the unit.When the unit is
locked, access is not allowed to the unit until the unit is unlocked.
Command form: DEVICE LFP [Value]
Argument details
Name
Device
LFP
Description
0–7 or * to select all units
Command form
Value
0 = Unlock Panel, 1 = Lock Panel, 2 = Toggle Value,
3 = Lock when timed out
Example: #54 LFP 1 The XAP 800 unit 4 (#54), front panel (LFP) is locked (1).
LMO - Last Mic On Mode
This command selects/reports last Mic on mode for the specified gating group.
Command form: DEVICE LMO <Channel> [Value]
Argument details
Name
Device
LMO
Description
0–7 or * to select all units
Command form
Channel
Value
See Groups and Channels, page 97
0 = Last Mic Mode disabled
1–8 = Select Last Mic mode on specified channel
* = Last mic to stay on, Null to return the current mode
Example: #50 LMO A 0 On XAP 800 unit 0 (#50), the Last Mic Mode (LMO
)
for gating group is disabled ( ).
A
0
LOCK - Preset and Macro Lock
This command selects/reports the state of the preset and macro lock.When on, the
lock prevents flagged presets and macros from being altered in any way.
Command form: DEVICE LOCK [Value][Password]
Argument details
Name
Device
LOCK
Description
0–7 or * to select all units
Command form
Value
0 = Off, 1 = On, 2 = Toggle
Only needs to be entered when changing the lock. For security,
this value is not returned.
Password
Example: #51 LOCK 1 “password” On XAP 800 unit 1 (#51), any presets or
macros that have been flagged with the LOCKPRST command will be locked
(LOCK) and password protected (1) with the macro/preset password
(LOCKPWD).
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
112
LOCKPRST - Apply the lock to a preset or macro
Selects/reports whether the lock is applied to a preset/macro. If a preset/macro has
the lock applied, it can only be changed if unlocked with the password.
Command form: DEVICE LOCKPRST <Channel><Group>[Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
LOCKPRST
Channel
Group
1–32 (Preset) or 1–255 (Macro)
S = Preset, C = Macro
Value
0 = Off, 1 = On, 2 = Toggle, Null = Query (value is only
returned if unit is unlocked)
Example: #52 LOCKPRST 5 S 1 On XAP 800 unit 2 (#52), preset 5 (5 S) will
be protected ( ) whenever the lock option is enabled.
1
LOCKPWD - Set preset/macro password
Selects/reports the password for the preset/macro lock.This can only be changed if
unit is unlocked.
Command form: DEVICE LOCKPWD [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
LOCKPWD
Value
1–12 characters
Null = Query (value is only returned if unit is unlocked)
Example: #53 LOCKPWD mypassword On XAP 800 unit 3 (#53), the
macro/preest password (LOCKPWD) is set to mypassword
.
LVL - Level
This command reports the level.This command is read only.
Command form: DEVICE LVL <Channel> <Group> [Position] [Value]
Argument details
Name
Device
LVL
Description
Units
0–7 or * to select all units
Command form
Channel
Group
Position
Value
See Groups and Channels, page 97
See Groups and Channels, page 97
See Meter Type Definitions, page 98
-99.99 to 99.99
dB
Sent with Null in text, value returned
Example: #51 LVL 8 L I 3 The level (LVL) received from XAP 800 unit 1 (#51
for line level ( ) Input at the Input stage ( ) is dB.
)
L
8
I
3
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
113
LVLREPORT - Level Report
This command selects level status reporting.
Command form: DEVICE LVLREPORT <Channel> <Group> [Position] [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
LVLREPORT
Channel
Group
Command form
See Groups and Channels, page 97
See Groups and Channels, page 97
See Meter Type Definitions, page 98
0 = Off (Delete level from list of levels to be reported)
1 =On (Add specified level to list of levels to be reported)
2 = Toggle
Position
Value
Example: #52 LVLREPORT 8 L I 1 On XAP 800 unit 2 (#52), the level
LVLREPORT) of line level ( ) input at the input stage ( ) is to be added (
the report.
(
L
8
I
1) to
LVLRRATE - Level Report Rate
Sets the level report rate for the unit and activates/deactivates level repeating.
Command form: DEVICE LVLRRATE [Value]
Argument details
Name
Description
Units
Device
0–7 or * to select all units
Command form
LVLRRATE
Value
0 = Turn off reporting but leave current list
1 = Turn off reporting and clear the list
50 to 1000 = Set Rate (1 meter every x ms) ms
Null to return current value
Example: #53 LVLRRATE 100 On XAP 800 unit 3 (#53), the level report rate
LVLRRATE) is set to 100ms.
(
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
114
The response indicates
execution of the macro,
but does not indicate that
MACRO - Macro Execution/Reporting
✍
This command executes a specified macro or reports the last macro executed.There
are 255 macros that can be specified.
each command within the macro
was executed.
Command form: DEVICE MACRO [Value]
Argument details
Name
Device
MACRO
Value
Description
0–7 or * to select all units
Command form
1-255 Value to execute user macros
Example: #55 MACRO 1 On XAP 800 unit 5 (#55), Macro (MACRO
)
1
is run.
MASTER - Expansion Bus Master Mode
This command reports the mode of the unit.The mode can be Master or Slave.
Command form: DEVICE MASTER [Value]
Argument details
Name
Description
Device
MASTER
Value
0–7 or * to select all units
Command form
1 = Master, 2 = Slave, Null = Current mode of the unit
Example: #56 MASTER 2 On XAP 800 unit 6 (#56), the MASTER mode is set
to slave (
2)
MAX - Maximum Gain Setting
This command changes or reports back the maximum gain setting for an input,
output or assignable processing block.
This setting will affect all
Command form: DEVICE MAX <Channel> <Group> [Value]
relative gain adjustments.
✍
Argument details
Name
Device
MAX
Description
Units
0–7 or * to select all units
Command form
Channel
Group
Value
See Groups and Channels, page 97
I, O, M, P, L
-65.00 to 20.00
dB
Null to return the current setting
Example: #51 MAX 2 M 10 On XAP 800 unit 1 (#51), the maximum (MAX
relative gain setting for mic ( ) channel is 10dB.
)
M
2
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
115
MDMODE - Modem Mode
This command enables or disables the modem mode for the unit.When the modem
mode is enabled, the modem initialization string is sent out the serial port and the
serial port now requires a password before a command is processed. After five
minutes of serial inactivity the passcode will be requested to continue serial activity.
Command form: DEVICE MDMODE [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
MDMODE
Value
Command form
0 = Off, 1 = On, 2 = Toggle, Null = current modem mode state
Example: #57 MDMODE 1 On XAP 800 unit 7 (#57), the modem mode
MDMODE) is on ( ).
(
1
MIN - Minimum Gain Setting
This command changes or reports back the minimum gain setting for an input,
output or assignable processing block.
Command form: DEVICE MIN <Channel> <Group> [Value]
Argument details
Name
Device
MIN
Description
Units
0–7 or * to select all units
Command form
Channel
Group
Value
See Groups and Channels, page 97
I, O, M, P, L
-65.00 to 20.00
dB
Null to return the current setting
Example: #54 MIN 2 M -10 On XAP 800 unit 4 (#54), the minimum (MIN
)
relative gain setting for mic ( ) channel is -10dB.
M
2
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
116
MINIT - Modem Initialization String
This command sets/reports the modem initialization string of the serial port when in
modem mode.
Command form: DEVICE MINIT [String]
Argument details
Name
Device
MINIT
String
Description
0–7 or * to select all units
Command form
1-80 characters (select string characters to be sent to the modem
when the unit is initialized
CLEAR = clears the modem initialization string
Null = Current string
Example: #56 MINIT ATZ On XAP 800 unit 6 (#56), the modem initialization
string (MINIT) is ATZ
.
MINMAX - Minimum and Maximum Gain Setting
This command changes or reports back the minimum and maximum gain setting for
an input, output or assignable processing block.
Command form: DEVICE MINMAX <Channel> <Group> [Minimum] [Maximum]
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
MINMAX
Channel
Group
See Groups and Channels
I, O, M, P, L
Minimum
Maximum
-65.00 to 20.00, Null to return current settings
-65.00 – 20.00
Example: #55 MINMAX 2 M -12 10 On XAP 800 unit 5 (#55), the minimum
and maximum (MINMAX) relative gain settings for mic (
M) channel
2
are -12dB
and 10dB respectively.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
117
MLINE - Mic/Line Adjust
This command selects/reports the setting of coarse gain adjustment on the input
channels 1-8.The three settings are 0dB, 25dB, and 55dB.
Command form: DEVICE MLINE <Channel>[Value]
Argument details
Name
Device
MLINE
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (selects mic inputs)
0 = 0dB (line level), 1 = 55dB, 2 = 25dB, Null = current level
Example: #53 MLINE 1 2 On XAP 800 unit 3 (#53), the mic/line (MLINE
)
setting for input is 25dB ( ).
1
2
MMAX - Maximum Number of Microphones
This command selects/reports the maximum number of microphones for each gating
group.
Command form: DEVICE MMAX <Channel> [Value]
Argument details
Name
Device
MMAX
Channel
Value
Description
0–7 or * to select all units
Command form
1–4, A-D (gating groups)
0 = Unlimited, 1–8 = Maximum number of mics
Null = Current maximum number of microphones
Example: #52 MMAX A 4 On the XAP 800 unit 2 (#52), the max number of
mics (MMAX) in gating group that are allowed to gate on at any one time is
A
4.
MPASS - Modem Password
Once the command is
given, the unit responds by
This command sets the current password setting for the unit when using modem
mode.The password must be entered in twice.
✍
echoing
back
the
Command form: DEVICE MPASS [String]
command, followed by “RE-
ENTER PASSWORD” string. The
command must then be re-entered
exactly as entered previously.Then,
the command will be echoed back,
followed by an“OK,”indicating that
the password has been changed.
Argument details
Name
Device
MMAX
String
Description
0–7 or * to select all units
Command form
0-12 characters, CLEAR = to clear the current password
Null to report the current password
Example: #50 MPASS GENTNER On XAP 800 unit 0 (#50), the modem
password (MPASS) is set to GENTNER
.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
118
SRC = source
MTRX - Matrix
DEST = destination
✍
This command selects/reports the matrix routing of an input to an output.
Command form: DEVICE MTRX <SRC CHNL> <SRC GRP> <DEST CHNL>
<DEST GRP> [Value]
CHNL = channel
GRP = group
Argument details
Name
Description
Device
0–7 or * to select all units
Command form
MTRX
SRC CHNL
SRC GRP
DEST CHNL
DEST GRP
Value
See Groups and Channels, page 97
I, M, P, L, E
See Groups and Channels, page 97
O, P, E
0 = Cross point off
1 = Cross point on (not valid for mic sources)
2 = Cross point toggle (not valid for mic sources)
3 = Non-gated (mic sources only)
4 = Gated (mic sources only)\
Null = Current mode
Example: #57 MTRX 1 M 4 O 4 On XAP 800 unit 7 (#57), mic (
M) channel
1
is routed (MTRX) as gated ( ) to output (
4
O)
4.
MTRXLVL - Matrix Attenuation Adjustment
This command selects/reports the matrix level at the cross point.
Command form: DEVICE MTRXLVL <SRC CHNL> <SRC GRP>
< DEST CHNL> <DEST GRP> [Value] [A/R]
Values indicate entry
range only. Actual internal
range of the gain stage is
Argument details
✍
Name
Description
Units
Device
0–7 or * to select all units
Command form
f
r
o
m
MTRXLVL
SRC CHNL
SRC GRP
DEST CHNL
DEST GRP
Value
-60 to 0 and absolute values will be
limited to the internal gain range.
Absolute levels below -60 will mute
the gain stage.
See Groups and Channels, page 97
I, M, P, L, E
See Groups and Channels, page 97
O, P, E
-99.99 to 99.99
dB
Null = Current mode
A = Absolute
A/R
R = Relative, Null = Relative
Example: #50 MTRXLVL 1 M 4 O -6 On XAP 800 unit 0 (#50), cross point
attenuation (MTRXLVL) at the point of mic ( and output ( is -6dB.
M)
1
O)
4
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
119
MUTE - Mute
This command selects/reports the setting of mute on input, output or processing
channels.
Command form: DEVICE MUTE <Channel> <Group> [Value]
Argument details
Name
Device
MUTE
Channel
Group
Value
Description
0–7 or * to select all units
Command form
See Groups and Channels, page 97
I, O, M, P, L
0 = Off, 1 = On, 2 = Toggle, Null = current mode
Example: #51 MUTE 2 M 1 On XAP 800 unit 1 (#51), the mute (MUTE) for
mic ( ) channel is on ( ).
M
2
1
NCD - Noise Cancellation Depth
Noise cancellation must
be enabled for this
command to have any
effect on audio quality.
This command selects/reports the noise cancellation amount for each mic channel.
✍
Command form: DEVICE NCD <Channel> [Value]
Argument details
Name
Device
NCD
Description
0–7 or * to select all units
Command form
Channel
Value
1–8 (select mic input)
6 - 15 (set noise cancellation from 6 to 15dB),
Null to return the current mode
Example: #52 NCD 1 9 On XAP 800 unit 2 (#52), the noise cancellation depth
NCD) of mic channel is dB.
(
1
9
NCSEL - Noise Cancellation Select
This command selects/reports the Noise Cancellation for each mic channel.
Command form: DEVICE NCSEL <Channel> <Value>
Argument details
Name
Device
NCSEL
Channel
Value
Description
0–7 or * to select all units
Command form
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current state
Example: #53 NCSEL 2 1 On XAP 800 unit 3 (#53), the noise cancellation
NCSEL) for mic channel is enabled ( ).
(
2
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
120
This setting is not affected
by the echo canceller
settings.
NLP - Non-Linear Processing Adjust
✍
This command selects/reports the setting of the Non-linear processing for each
microphone channel.
Command form: DEVICE NLP <Channel> [Value]
Argument details
Name
Device
NLP
Description
0–7 or * to select all units
Command form
Channel
Value
1–8 (select mic input)
0 = Off, 1 = Soft, 2 = Medium, 3 = Aggressive
Null = Current mode
Example: #54 NLP 2 1 On XAP 800 unit 4 (#54), the non-linear processing
NLP) for mic channel is set to soft ( ).
(
2
1
NOM - Number of Open Microphones Mode
This command selects/reports the setting of Number of Open Microphones (NOM) on
output channels. Command form: DEVICE NOM <Channel> [Value]
Argument details
Name
Device
NOM
Description
0–7 or * to select all units
Command form
Channel
Value
1–12 (select output)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #55 NOM 2 1 On XAP 800 unit 5 (#55), the number of open
microphones (NOM) attenuation for output is on ( ).
2
1
OFFA - Off Attenuation Mode
This command selects/reports the off attenuation mode of input channels 1–8.
Command form: DEVICE OFFA <Channel> [Value]
Argument details
Name
Device
OFFA
Channel
Value
Description
Units
0–7 or * to select all units
Command
1–8 (select mic input)
0–60 (select off attenuation level)
Null to return the current off attenuation level
dB
Example: #56 OFFA 1 12 On XAP 800 unit 6 (#56), the off attenuation (OFFA
)
for mic channel is 12dB.
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
121
PAA - PA Adaptive Mode
This command selects/reports PA adaptive mode for the specified mixer.There can be
only one selection per mixer.
Command form: DEVICE PAA <Channel> [Value]
Argument details
Name
Device
PAA
Description
Units
0–7 or * to select all units
Command
Channel
Value
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #57 PAA 1 0 On XAP 800 unit 7 (#57), the PA adaptive mode (PAA
on mic channel is disabled ( ).
)
1
0
PP - Phantom Power
This command selects/reports the setting of phantom power.
Command form: DEVICE PP <Channel> [Value]
Argument details
Name
Device
PP
Description
Units
0–7 or * to select all units
Command
Channel
Value
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #51 PP 2 1 On XAP 800 unit 1 (#51), the phantom power supply
PP) for mic channel is enabled ( ).
(
2
1
PRESET - Preset Execution/Reporting
This command selects/reports the state of a preset.
Command form: DEVICE PRESET <Channel> [Value]
Argument details
Name
Description
Units
Device
PRESET
Channel
Value
0–7 or * to select all units
Command
1–32 (select preset)
0 =Set the preset state to off
1 = Execute the preset and set the state to on
2 = Execute the preset and set the state to off
Null = Returns the current preset state
Example: #52 PRESET 5 1 On XAP 800 unit 2 (#52), preset (PRESET
execute and set the state to on ( ).
)
5
will
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
122
PRGSTRING - Program String
This command sets/reports a programmed string.
Command form: DEVICE PRGSTRING <ID> [Value]
Argument details
Name
Device
PRGSTRING
ID
Description
0–7 or * to select all units
Command
0 – 7 (string location)
1–80 Characters
Value
CLEAR = Clear current value
Null = Current value
Example: #53 PRGSTRING 2 MUTE On XAP 800 unit 3 (#53), string location
is programmed (PRGSTRING) with MUTE
2
.
Supported special characters
\a = alert
\b = backspace
\f = formfeed
\n = new line
\r = carriage return
\t = horizontal tab
\v = vertical tab
\\ = backslash
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
123
RAMP – Ramp Gain Adjustment
This command starts/stops the gain ramp for an input, output, or assignable
processing block.There is no query for this command.
Command form: DEVICE RAMP <Channel><Group><Rate>[Target]
Argument details
Name
Device
RAMP
Channel
Group
Rate
Description
Unit
0–7 or * to select all units
Command
See Groups and Channels, page 97
I, O, M, L, P,T, R (1, 2, 3, 5, 16, 17)
-50 to 50
dB/s
dB
If value = 0. the ramp will stop
If value < 0, the gain will ramp down
If value > 0, the gain will ramp up
-65 to 20
Target
If null in text, the ramp will use the
channel’s maximum and minimum for a target
Example: #57 RAMP 5 L 6 12 On XAP 800 unit 7 (#57), the gain (RAMP) on
ine Input will increase at a rate of 6dB/sec until the 12dB point is reached.
L
5
REFSEL - PA/AEC Reference Select
This command selects/reports which output is used for each mic as a reference for
power amp adaptation mode and acoustic echo cancellation where applicable.There
can be only one selection per mixer.
Command form: DEVICE REFSEL <Channel> [Ref. Group] [Ref. Channel]
Argument details
Name
Description
Device
0–7 or * to select all units
Command
REFSEL
Channel
1–8 (select mic input)
0 = Output, E = Expansion bus
1–9, O–Z (select output or E-bus channel)
Ref. Group
Ref. Channel
Example: #50 REFSEL 1 O 8 On XAP 800 unit 7 (#50), the PA/AEC reference
REFSEL for mic channel is output ( 12
1
O)
.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
124
REFSET - Reference channel setup
This command selects/reports the output the reference channel tracks.
Command form: DEVICE REFSET <Channel> <Group>[Value]
Argument details
Name
Device
REFSET
Channel
Group
Description
0–7 or * to select all units
Command
1–4 (select Virtual Reference number)
1–9 (select output channel to track)
0 = none
Value
Example: #53 REFSET 2 4 On XAP 800 unit 3 (#53), virtual reference (2) will
track gain changes mde on output channel 4.
SERECHO - Serial Echo
This command selects/reports the serial echo of the RS-232 port.
Command form: DEVICE SERECHO [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command
SERECHO
Channel
Value
See Groups and Channels, page 97
0 = Off, 1 = On, 2 = Toggle, Null = Current state
Example: #54 SERECHO 1 On XAP 800 unit 4 (#54), the serial echo
SERECHO) of the RS-232 port is set to on ( ).
(
1
If the serial mode is
changed, the terminal will
not see a response from
SERMODE - Serial Mode
This command selects/reports the serial mode of the RS-232 port.
✍
Command form: DEVICE SERMODE [Value]
the unit, nor will the unit respond
to commands until the new status
is matched by the terminal.
Argument details
Name
Description
Device
0–7 or * to select all units
Command
SERMODE
Value
1 = Text, 2 = Binary, Null = Current mode
Example: #55 SERMODE 1 On XAP 800 unit 5 (#55), the RS-232 port serial
mode (SERMODE) is set to text ( ).
1
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
125
SFTYMUTE - Safety mute
Selects/reports the state of the safety mute.When on, the safety mute holds all
outputs on the selected unit in a muted state. It is used primarily for troubleshooting
G-Ware.
Command form: DEVICE SFTYMUTE [Value]
Argument details
Name
Description
Device
0–7 or * to select all units
Command
SFTYMUTE
Value
0 = Off, 1 = On, 2 = Toggle, Null = Current state
Example: #52 SFTYMUTE 1 On XAP 800 unit 2 (#52), safety mute
SFTYMUTE) is enabled ( ).
(
1
SIGGEN - Signal Generator
This command selects/reports of the signal generator activation.
Command form: DEVICE SIGGEN <Channel> <Group> [Type] [Amplitude]
[Frequency]
Argument details
Name
Description
Device
0–7 or * to select all units
SIGGEN
Channel
Group
Command
See Groups and Channels, page 97
I, M, L
Type
0 = Off, 1 = Pink, 2 = White, 3 = Tone, Null = Current state
-60 to +20 amplitude in dB; NULL for type 0
20 to 20,000 frequency in Hz (only needed when using tone
generation)
Amplitude
Frequency
Example: #56 SIGGEN 1 M 2 0 On XAP 800 unit 6 (#56), the signal gen-
erator (SIGGEN) is set to input at mic ( ) channel with white noise ( ) at 0dB.
M
1
2
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
126
SIGTOUT - Signal Generator Time Out
Sets the signal generator time out for the unit.
Command form: DEVICE SIGTOUT [Value]
Argument details
Name
Device
SIGGEN
Value
Description
0–7 or * to select all units
Command
0 = Off, 1–30 = Set time out minutes, Null = Current rate
Example: #57 SIGTOUT 15 On XAP 800 unit 7 (#57), the signal generator
time out (SIGTOUT) is set to 15 minutes.
SLVL - Speech Level Control Enable/Disable
This command selects/reports the setting of speech level control for a microphone.
Command form: DEVICE SLVL <Channel> [Value]
Argument details
Name
Device
SLVL
Description
0–7 or * to select all units
Command
Channel
Value
1–8 (select mic input)
0 = Off, 1 = On, 2 = Toggle, Null = Current mode
Example: #50 SLVL 2 M 1 On XAp 400 unit 0 (#50), the speech leveler for mic
) channel is set to on ( ).
(M
2
1
STRING - String Execution
This command sends the specified string out the serial port.
The serial command to
create string is
PRGSTRING (Program
String). See page 122.
Command form: DEVICE STRING [ID]
a
✍
Argument details
Name
Device
STRING
ID
Description
0–7 or * to select all units
Command
0 – 7
Null to query last string in text
Example: #51 STRING 3 On XAP 800 unit 1 (#51), the STRING programmed
into location will be sent out the RS-232 port.
3
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix E: Serial Commands
127
TOUT - Time Out Select
This command selects/reports the inactivity time out before returning to the unit title
screen.
Command form: DEVICE TOUT [Value]
Argument details
Name
Device
TOUT
Value
Description
0–7 or * to select all units
Command
0 = Off, 1–15 (select time out in minutes)
Null = Current mode
Example: #52 TOUT 5 On XAP 800 unit 2 (#52), the front panel of the unit will
time out (TOUT) after
5
minutes.
UID - Unit ID
This command reports the unit ID.This command is read only.
Command form: DEVICE UID [Value]
Argument details
Name
Device
UID
Description
Units
0–7 or * to select all units
Command
Value
Null to return value
Hexadecimal
Example: #53 UID B465F991 The unit ID number (UID) received from XAP 800
unit 3 (#53), is B456F991
.
VER - Version
This command reports the firmware version of the unit. This command is read only.
Command form: DEVICE VER [Value]
Argument details
Name
Device
VER
Description
0–7 or * to select all units
Command
Value
Null to return value
Example: #54 VER 1.0.0 The version of the firmware (VER) programmed into
XAP 800 unit 4 (#54), is 1.0.0
.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix F: Warranty
128
Appendix F: Warranty
ClearOne Communications, Inc. (Manufacturer) warrants that this product is free of
defects in both materials and workmanship. For full warranty information and
coverage, refer to the ClearOne website at www.clearone.com.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix F: Warranty
129
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Appendices ~ Appendix G: Compliance
130
Appendix G:
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules.These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his/her own expense.
Changes or modifications not expressly approved by ClearOne Communications
could void the user’s authority to operate the equipment.
This equipment meets the following compliance standards:
USA: FCC and CSA
Europe: CE
Canada: IC and CSA
Mexico: NOM and Cofetel
South Africa: SABS
Australia: ACA
Japan:VCCI and JATE
This equipment complies with the requirements of the EU guidelines:
89/336/EEC :
73/23/EEC
”Electromagnetic Compatibility”
“Electrical operating material for use within specific
voltage limits”
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device may not cause harmful interference that may cause undesired
operation.
Safety Information
CAUTION: Users should not attempt to make such connections themselves, but
should contact the appropriate electrical inspection authority, or electrician, as
appropriate.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
131
Glossary
Acoustic Echo Cancellation (AEC) A process in which acoustical echo is
removed from a signal. AEC can be used to remove unwanted signals from mic audio
if the unwanted acoustic signal is available separately as an electronic signal.
Adaptive Ambient This portion of the mixer monitors the varying ambient noise
level in the room and changes the threshold level at which a microphone gates on.
Ambient Level The manually-set background noise level upon which the XAP 800
bases gating protocols. Used only if the Adaptive Ambient feature isn’t used.
Ambient Noise The existing room-level noise, such as that caused by ventilation
systems, paper shuffling, and background chatter.
Amplitude Plot A plot of amplitude (-18 to 18dB) vs. frequency (20Hz to 20kHz)
on a logarithmic scale.
Attack Time This signal parameter determines how quickly compression is enabled.
It is calibrated in milliseconds.
Attenuation A reduction of signal amplitude.
Audio Processor A device that modifies an audio signal in response to certain
requirements.
Audio routing The process of routing input signals (Mics 1–8, Inputs 9-12, From
E-bus, From Processing) to output destinations (Output 1–12,To E-bus,To
Processing) in the Matrix screen.
Automatic Gain Control (AGC) Automatically increases or decreases audio gain
to maintain a consistent audio level.
Automatic Gating Automatically gates microphones on or off based on input levels
and other parameters programmed into the XAP 800.
Auxiliary audio Audio that comes from line level audio sources such as video
codecs,TH2s, and CD players.
Bandwidth The difference between the lower and upper 3dB end points of an audio
band. Also, the range or differences between the limiting frequencies of a continuous
frequency band.
Baud Rate The number of signal transitions per second, or the clock rate of the
serial bit stream in hertz. Given 7 or 8 bits for data plus start and stop, the
approximate ASCII character transmission rate is one-tenth the baud rate.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
132
Chairman Override Provides gating priority for chairman override enabled
microphones within the same gating group.When a mic with chairman override gates
on, all mics which don’t have chairman override enabled and are in the same gating
group will gate off.
Clipping A condition in which a signal level exceeds the maximum level a circuit can
handle.This is usually caused by improper gating parameters and gain settings. It
causes distortion and typically leads to listener fatigue and accelerated failure of
loudspeaker drivers.
Compression An induced reduction in the dynamic range of part or all of an audio
signal. Compression is usually used to protect individual loudspeaker components
from the damaging effects of transients.
Compressor The compressor is part of the processing settings and allows you to
change the gain transfer characteristics of the signal path and to control the
dynamics of the signal.
Configuration mode Configuration mode is the default mode in G-Ware and is
used for system setup. It provides access to the Matrix and Flow Screens. See also
Preset mode and Macro mode.
Control bus Part of the expansion bus, the control bus passes control information
to the units. Control is not affected by master/slave settings and will continue to
function even if the units are not using the audio channels.
Constant Directivity Horn Equalizer (CD Horn EQ) Horn drivers commonly
used in arrays in arenas and auditoriums have an inherent 6dB/octave high frequency
rolloff.The XAP 800’s CD Horn EQ compensates for this characteristic.
Crossover A device that passes designated frequency segments of an audio signal to
various loudspeaker elements in a sound system.
•
•
Bessel A crossover using a low-pass filter design characterized by a linear
phase response.This results in a constant time delay throughout the passband.
Butterworth A crossover using a low-pass filter design characterized by a
maximally flat magnitude response.This results in no amplitude ripple in the
passband.
•
Linkwitz-Riley A fourth-order crossover consisting of a cascaded second-
order Butterworth low-pass filter. Offers a vast improvement over the
Butterworth crossover and is the de facto standard for professional audio
active crossovers.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
133
Cross point The intersection between an input and an output in the routing matrix.
Cross point cells are colored according to input type.
Cross point attenuation The process of attenuating audio level at the cross point.
Audio can be attenuated from 0 to 60dB.
Decay Rate (slow, medium, fast) Determines how fast a channel gates off after
hold time expires. Default is medium.
Default meter The input/output displayed on the front panel LED meter when a
input/output meter is not specifically selected elsewhere.
Delay A setting in the Processing window. Delay calculates the amount of signal
delay (up to 500ms) based on the distance between audio source and audience and
the temperature.
Device ID A number which identifies the unit when multiple units of the same
device type are connected in an E-bus network. Because up to eight XAP 800s may
be used in the same network, the device ID range is 0–7.
Device Type A number which identifies the type of unit. For example, a XAP 800
is device type 5.
DSP Digital signal processor.
Echo Canceller Reference The signal point which contains an electronic copy of
all signals which will be removed from the signal the mics pick up.This is always the
far-end audio and, optionally, local program material.
EC Reference summing The ability to include multiple signals in a single
reference. See also Virtual Reference.
ERL Found in the Acoustic Echo Canceller window, the echo return loss (ERL)
meter shows the coupling between the reference signal and the input to the echo
canceller—the ratio of the two levels.
ERLE Found in the Acoustic Echo Canceller window, the echo return loss
enhancement (ERLE) meter shows the loss through the echo cancellation and non-
linear processing chain—the ratio of the two levels.
Expansion Bus Consists of two RJ-45 connectors on the rear panel of the XAP
800. An Expansion Bus allows multiple XAP 800s to be networked together using
category five twisted-pair (10BaseT) cable.
Expansion Bus reference One of the echo cancellation/PA adapt reference
options.The Expansion Bus reference allows you to reference an output on a
networked unit.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
134
Filter A device that passes and blocks audio signals based on user-definable
requirements of the system.
•
All Pass A filter that provides only phase shift or phase delay without
appreciably changing the magnitude characteristic.The filter produces a flat
amplitude response. It is useful for matching the delay of two processing
channels with different delays.
•
•
High Pass A filter that passes high signal frequencies while attenuating low
frequencies.The gain or loss
High Shelving Provides boosting or attenuation of frequencies above a
designated frequency.The transition between the spectrum above and below
the designated frequency occurs at a fixed 6dB/octave rate.The gain or loss
above the corner frequency is adjustable to +/- 15dB.
•
•
Low Pass A filter that passes low frequencies while attenuating high
frequencies.
Low Shelving Provides boosting or attenuation of frequencies below a
designated frequency.The transition between the spectrum above and below
the designated frequency occurs at a fixed 6dB/octave rate.The gain or loss
below the corner frequency is adjustable to +/- 15dB.
Filter Display A group of nodes plotted on a logarithmic scale.The
XAP 800’s filter display can be accessed through the Inputs 1-8, From Processing,
or To Processing windows.
First Mic Priority Increases the audio level required to gate on additional
microphones after the first mic is on.This helps ensure that only one mic gates on
when a person speaks.
Flow control The regulation of the transmission and reception of data.
Flow Screen The Flow Screen is the main access window for G-Ware features and
unit configuration. It also shows a detailed block diagram of the audio signal—
presenting a graphical explanation of each stage in the signal path.
Gain The amount a signal is increased over a given reference, typically 0. Normally
specified in dB (decibels). On the XAP 800, gain is adjustable from -65 to 20dB
(85dB range) in .5dB increments.
Gain Structure The configuration of parameters which define gain adjustment of a
signal.The optimal input gain setting is one which provides both an adequate signal-
to-noise ratio and reasonable headroom.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
135
Gate The activation and deactivation of microphones.
•
•
•
Auto The microphone will gate on according to the input level, assigned
gating parmeters, and gating group.
Manual On The microphone will gate on unless it exceeds the NOM
requirements of the gating group.
Manual Off The microphone is deactivated.
Gate Ratio Specifies how much louder the microphone audio level must be above
the ambient sound level before a microphone gates on.
Gating controls The gating parameters that are assigned to a gating group:
Maximum Number of Mics, First Mic Priority, and Last Mic Mode.
Gating groups A set of gating parameters which can be applied to local
microphones (Internal 1–4) or to microphones connected to other units on the
network (Global A–D). Gating groups provide greater flexibility and control of mics.
Gentner Distributed Echo Cancellation ClearOne’s proprietary system for
applying echo cancellation individually to each mic input.
Global gating bus Part of the expansion bus, these four mix-minus buses pass mic
status and gate parameter information such as First Mic Priority and Max NOM.
GPIO (general purpose input/output) The Control/Status A and B ports on the
XAP 800 unit.The GPIO Builder is used to program Control/Status A pins.
G-Ware Software The XAP 800’s setup and configuration software.
Hold Time The length of time that a microphone remains on after the voice (input)
level drops below the gate ratio.This can be used to prevent the microphone from
gating off during brief pauses in speech.
Last Mic Mode Sets the last-activated mic to Last On, Mic 1-8, or Off.The Last On
setting leaves the last-activated mic gated on until another mic input gates on.
Macro A series of user-created instructions, stored within the unit, which can be
executed from an RS-232 command or contact closure.
Macro Mode The G-Ware mode that allows you to customize and execute macro
commands for a XAP 800 unit or network.
Manual Gating Provides the ability to gate a microphone on or off manually.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
136
Matrix Mixer A mixer that allows routing of any input or combination of inputs to
an output or any combination of outputs. In the case of the XAP 800, the matrix
mixer permits level control at each cross point in the matrix.
Matrix Screen The Matrix Screen facilitates the routing of any input to any output
or combination of outputs.
Maximum Number of Mics Sets the maximum number of mics that can be gated
on simultaneously.
Microphone Activation A condition in which a microphone is gated on.
Microphone Mixing A situation in which audio from mics on different signal lines
are mixed together. All mic signals can be mixed to one signal line, any or all outputs,
or mixed into separate groups. Mic signals can also be processed together or
individually.
Microphone 1 Mode Reverts mic assignment to a designated mic when all mics
gate off.
Min/Max adjust The yellow and blue upper and lower limit arows on gain scales
are used to create minimum and maximum gain level limits. These limits only apply
when using relative gain commnds; absolute gain commands can exceed the min and
max limits. Min and max limits apply to all serially connected control devices and
preven users from adjusting levels beyond the min/max levels provided relative gain
commands are used.
Mixer mode The mixer mode has two settings: master and slave. Mixer mode can
be configured from the front panel or in the Unit Properties window.
Mute A condition in which an audio signal is attenuated below the audible
threshold.
Noise Cancellation A process through which ambient noise is removed from a
signal.
Non-linear processing (NLP) NLP increaess the power of echo cancellation for
difficult acoustical environments. NLP has four settings: Soft (6dB), Medium
(12dB), Aggressive (18dB), and Off. NLP settings are found in the Acoustic Echo
Cancellation window.
Number of Open Mics (NOM)/Constant Gain Mode Adjusts the output level
based on the number of mics gated on and routed to an output.
O–R buses These four audio buses communicate NOM count and mic mixing
parameters.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
137
Off Attenuation The amount of level reduction a microphone is given when the
microphone is not gated on.
PA Adaptive Mode The XAP 800 recognizes how much loudspeaker audio is
picked up by the microphones and then uses this level as the new ambient level when
audio is present at the power amplifier.This prevents loudspeaker audio from gating
on a microphone, while still allowing people in the room to gate on microphones as
they speak.
PA Adapt/AEC Reference This G-Ware setting determines which output (typically
for a loudspeaker) is used as a reference for an input.
PA Adapt/AEC Reference bus This bus carries reference information making it
possible for an input to reference an output on another linked unit.
Parametric Equalizer (PEQ) A multi-band variable equalizer with control of
gain, center frequency, and bandwidth. A properly configured PEQ enables the XAP
800 to offset speaker or room acoustic deficiencies.
Passwords The XAP 800 features several passwords to protect system
configuration.
•
•
•
•
•
Front panel The front panel password prevents a user from changing settings
in the front panel LCD menus.The password can be set from the front panel or
through G-Ware.
Macro The macro password is created in the Unit Properties window and
makes it possible to lock certain macros. A locked macro can be run without
the password. However, a password must be entered to edit the macro.
Modem The modem password can be created serially using the MPASS
command or through G-Ware in the Unit Properties window.The password is
required to allow remote modem access.
Preset The preset pasword is created in the Unit Properties window and
makes it possible to lock certain presets. A locked preset can be executed
without the password. However, a password must be entered to edit the preset.
Site file (File Access) The site file password is set in the Site Properties
window and will lock the site file. Users must enter the password in order to
open the site file.
Phantom Power Power supplied by the XAP 800 to power most condenser
microphones.The XAP 800 provides 24 volts of phantom power.This feature can be
switched off for devices not requiring phantom power.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
138
Phase Plot A plot of phase angle (-180 to 180 degrees) vs. frequency (20Hz to
20kHz) on a logarithmic scale.
Pink Noise An audio test signal containing all the frequencies in a given audio
spectrum, with equal energy in each octave.
Preset One of 32 configurable memories in the XAP 800. A preset can be
programmed with a variety of routing, level, gating, delay, filter, and equalizer settings
to meet specific application requirements.
Preset Mask Defines whether a contact closure activates on a low or high signal on
the rear panel of the unit.
Preset Mode Preset mode is used to create presets and is accessed from the G-
Ware toolbar.
Processing blocks There are four processing blocks or channels (A–H) in the XAP
800 each with 15 filters, delay, and a compressor for pinpoint audio configuration. A
single input or group of inputs can be routed through a processing block and then
routed to an output or multiple outputs.
Q
Quality factor. It is the ratio of the center frequency divided by the bandwidth. Q
reflects an inverse relationship to the bandwidth, and adjusts from .02:1 to 40:1 on
the XAP 800.
Ratio The amount of compression applied to the output signal compared with the
input signal as the signal exceeds the threshold level.
Release time Release is a parameter which determines how quickly compression is
released after the input signal drops below the threshold.
Reverberation A diffused acoustic energy field fed and maintained by sound
reflections from the room surfaces.
S–Z buses These eight buses are defaulted as auxiliary mix buses.They are used to
route auxiliary audio to and from other units on the network. These buses are also
used as mic mix buses when NOM count is not required.
Serial Command A bit description designed to execute an instruction or command.
Serial mode The serial mode determines the format in which serial commands
return—text or binary.The mode defaults to Binary when G-Ware is connected
and to Text when disconnected. Contact technical support for instructions on using
Binary mode.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Glossary
139
Signal Delay Used for:
•
Compensating for physical placement of multiple drivers in a cluster—to
align points of acoustic origin in the same plane.
•
•
Ensure matching arrival times at listeners from multiple loudspeaker drivers.
Using the Haas effect to maintain localization of the source, even with a
distributed system.
Signal Generator A device for generating a reference tone for sound system
calibration purposes.
Site file A site file is a file created by G-Ware which is saved on your computer.The
site file contains all information about a particular installation including all unit
settings and properties. It also provides G-Ware with the necessary informaiton to
communicate with the site hardware using your PC.
Site properties The Site Properties window opens when you select New Site from
the File menu or click on the New Site button on the toolbar. It allows you to enter
information about the site as well as configure the communication and security
settings.
Speech Leveler Essentially an AGC applied to a speech signal after processing by
a noise cancellation stage. Acts only on voice signals. Does not pull up the noise floor
during periods of no signal.
Table View Displays the numerical values of the filter parameters for all nodes of
the active filter display.
Threshold The upper or lower level at which a signal processing mechanism begins
or terminates operation.
Unit properties The Unit Properties window opens when you add a new unit to the
site. It allows you to enter information about the unit as well as configure the
communication and security settings.
Virtual reference Virtual references are echo cancellation reference points.
Multiple signals can be included in each of the four virtual references thus allowing
you to reference multiple signals without sacrificing an analog output.You can open
the Virtual Reference window from the G-Ware toolbar or from the Acoustic Echo
Cancellation window.
White Noise Acoustical noise with equal energy throughout a given frequency
range.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Index
140
Index
Compressor 49–51, 85, 102, 103, 132
attack time 49, 51, 102, 131
compression meter 51
group 50
A
acoustic echo cancellation 33–35, 40, 99, 131
echo return loss (ERL) 35
echo return loss enhancement (ERLE) 35
non-linear processing (NLP) 35
AEC settings 33–35
input meter 51
post compressor gain 50
ratio 51
total echo reduction 35
release time 49, 51
threshold 50
adaptive ambient 38, 39, 86, 99, 131
add unit 24
connect 10, 24
AEC see acoustic echo cancellation
AEC reference 7, 33, 38, 40
AGC see automatic gain control
ALC see automatic level control
All Pass 36, 51, 85, 86, 105, 134
ambient level 38–39, 42, 200, 131
ambient noise 35, 38, 131
attack time see Compressor
audio routing 6, 27, 29, 30, 31, 55, 131
O–Z routing 30
sync to document 24
Sync to Unit(s) 24
constant gain 46, 47, 136
control bus 6, 7, 132
Control Panels 6, 57, 60, 79–82, 91–93
connecting 91
Select panel 81
Volume panel 80
Control/Status A 10, 77, 88,
Control/Status B 61, 89
copy and paste 28, 31, 75
cross point 29, 30–31, 56, 119, 133
Cross Point Attenuation Dial window 30
crossover 53, 85, 105
Process A–D routing 30
Auto Sweep 77 see also Signal Generator
auto-detect 24
automatic gain control 32–33, 43–44, 99,
active gain 33
response time 33
D
target level 33
DEC see Gentner Distributed Echo Cancellation
default meter 16, 18, 25, 105
delay 6, 49, 53, 54, 103, 104,
device ID 12, 15, 25, 79, 105
device type 64, 79, 95
auxiliary audio 7, 30, 33, 44, 131
B
bandwidth 36, 37, 105, 131
baud rate 16, 23, 25, 82, 85, 101, 131
Distributed Echo Cancellation see Gentner
Distributed Echo Cancellation
Document Compare Utility 68
DSP 1, 105, 133
C
category five twisted-pair cable 11
Chairman Override 38, 86, 102, 132
Clear Matrix 30
E
clear password 15
EC Reference see AEC reference
ERL 16, 17, 35, 133
ERLE 16, 17, 35, 133
Execute Preset 60
expansion bus 41, 115, 133
connections 9, 11
labels 48
clipping 43, 45, 47, 54, 132
codecs see video codecs
COM port 21, 23
command line 60, 63, 65, 94
Command Strings 83
compare site 68
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Index
141
network 6, 11, 115
H
reference 33, 40, 58, 123
routing to 29, 30
High Pass 36, 51, 85, 86, 105, 134
hold time 39, 108, 135
Expansion Bus In/Out 5, 11, 85
I
F
Inputs 1–8 32
AEC 33
File Access Password 23
filter 35–37, 51–53, 105, 106, 134
First Mic Priority 42, 85, 106, 134
floppy disk 22
AGC/SL 32
filters 35
gate 38
flow control 15, 23, 25, 85, 106, 134
Flow Screen 27, 30
mute 32
NC 35
front panel control 4, 60 see also LCD menu
front panel passcode 15
PA Adapt and AEC Reference 33
phantom power 33
virtual echo cancellation reference 34
Inputs 9–12 44
AGC 44
G
G-Ware 22
installation 22
meters 45
Program Folder 22
G-Ware Switcher 74
gain structure 43, 45, 47, 54, 135
Gate 6, 7, 38
mute 44
Inputs menu 18
gain 18
mute 18
activation 38
adaptive ambient 38
ambient level 39
auto-gate 38
L
labels 27, 29, 48, 56, 57
Last Mic On 97, 111
chairman override 38
decay rate 39
latency
6
LCD menu 13, 16, 25
gate ratio 39
LCD menu tree 13
hold time 39
LCD Programming 13
manual off 38
adjust a parameter 14, 15
line level 32, 42, 44, 45, 46, 86
line level outputs 46
manual on 38
off attenuation 39
PA Adaptive mode 38
Gate View 75
Low Pass 36, 51, 85, 86, 105, 134
Gating Group 38, 41–42, 56, 110, 135
First Mic Priority 42
Global A–D 41
M
Macro Editor 26, 27, 63–66
macro password 26, 111–112, 137
Macro Recorder 27, 63, 65
macros 60–62, 63–66, 114, 135
editing macros 65
Internal 1–4 41
Last Mic Mode 42
Max # of Mics 41
Gentner Distributed Echo Cancellation 1, 32,
49, 133
Macro Editor 64–65
macro password 64
GFirm Firmware Utility 72
Macro Recorder 63
Global Gating Groups A-D buses
7
running macros 66
GPIO 5, 27, 57, 59, 60, 66, 77, 95, 135
G-Ware Switcher 74
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Index
142
master setting 12, 15, 114
Matrix Screen 27–32, 136
Message Log 28, 75
buses
7
PA Adaptive Mode 38
password 26
meter
4
front panel 26
Meter menu 16
Default Meter 18
ERL 17
file access 23
macro password 64
modem 26
ERLE 17
preset password 56
PEQ (parametric equalizer) 36
phantom power 33
pink noise 67
Inputs 17
Outputs 17
Processing 17
Meter reference 19
Meter View 76
Meters 43
pinouts 87
Control/Status A 88
Control/Status B 89
Line 90
post gain 43
post gating 43
RS-232 87
post processing 43
pre pain 43
RS-485 90
Set 90
Min/Max limits 42
mixer mode 9, 12, 14, 15, 136
modem 15, 16, 23, 26, 82, 87, 97, 115, 117
modem access 82
password 82
preset 5, 14, 26, 27, 55–62, 138
creating presets 55, 59
executing preset 60
front panel control 60
multiple presets 60
Preset Configuration pane 56
preset masking 57
preset password 56
preset state 60
N
NLP see non-linear processing
noise cancellation 35, 85, 119, 136
NOM 30, 38, 46, 47, 120, 136
non-gated 5, 29, 30, 44
Reference Matrix 58
Remote Assignment 57
room combining 61
routing matrix 56
running multiple presets 60
running presets 60
Preset mode 55
Print 28, 31, 58, 70, 71
matrix 31
non-linear processing 35, 98, 120, 136
Notch 36, 51, 85, 86, 105
O
Off LED/button
On LED/button
4
4
Outputs 1–12 5, 10, 18, 46, 47, 85
mute 46
preset 58
preview 70
NOM 46
reports 71
Outputs menu 18
gain 18
process meter 54
processing 16, 17, 25, 27, 29, 30, 49–54, 73,
85, 138
mute 18
O–R buses 6, 30, 136
Processing A–H 49
compressor 49
P
delay 53
PA Adapt and AEC Reference 6, 7, 33, 38,
40, 98, 120, 123, 137
filters 51
frequency response 52
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Index
143
System menu 14
Device ID 15
phase 52
mute 49
Firmware Version 15
Lock Panel 14
propagation 6, 54
Run Macro 14
R
Select Preset 14
Set Passcode 15
Unit ID 15
Ramp 123
release time 102, 138
Remote Builder 27, 78–82
Remote Panel 6, 10, 57, 90, 91–92
response time 33, 100 see also automatic gain
control
system requirements 21
S–Z 6, 7, 30, 158
T
RJ-45 jumper 11
target level 33
room combining 5, 60–62, 63
routing matrix 29, 30, 34, 40, 56
RS-232 10, 11, 12, 82, 83, 87, 101, 124
see also serial comands
threshold 33, 38–39, 49–51, 86, 102
Tone 68
RS-232 menu 15
U
Baud Rate 15, 85
Unit Properties 25–26
communication 25
default meter 25
device ID 25
Clear Password 16
Flow Control 16
Modem Mode 16
RS-485 Remote Panel A/B Port
6
meter refresh rate 25
preset/macro password 26
security 26
S
serial echo 25
Safety Mute 28, 125
security 26
serial mode 25
unit name 25
serial commands 5, 94–127
command responses 94
command structure 94
device type and ID 95
groups and channels 95
list of 97–98
unit type 25
use modem 26
Use in preset 57, 77
V
meter type 96
video codecs 30, 44, 46
signal flow 27, 43
site file 23, 24, 68, 139
Site Properties 16, 23, 25, 139
Communication 23
Security 23
video conferencing
9
Virtual Reference 34, 40, 58, 139
W
white noise 67
Use Modem 23
slave setting 12, 15, 25, 114
specifications 85
X
XAP IR Remote 78–79
Speech Leveler 32, 33
status bar 28
status lights 28
storage capacity 59, 63
Sync 24, 25, 28
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
|
Hotpoint 6531 User Manual
GE EER4000 User Manual
GE 164D2966P205 1 User Manual
Eizo T57S User Manual
Dell PowerEdge SE300 User Manual
Cadco LINE CHEF XAF 130 User Manual
Bloomfield Industries Wells Bloomfield Cooktop WV 2HSG User Manual
BenQ Computer Monitor G2000WA User Manual
AOC 9KLR User Manual
Addonics Technologies AEDVDCOPPM4U User Manual