OPERATION MANUAL
□ IC-18A INDUCTION COOKER
120V, 60Hz, 1.8KW
□ IC-22A INDUCTION COOKER
208V, 60Hz, 2.2KW
□ IC-25A INDUCTION COOKER
240V, 60Hz, 2.5KW
Cecilware Corporation
43-05 20th Avenue
Long Island City, NY 11105
Tel: 800.935.2211, 718.932.1414
Fax: 718.932.7860
Technical Support
Customer Service:
SUITABLE POTS & PANS, - FOR INDUCTION HEATING PLATES
1. Iron
2. Cast iron
3. Stainless steel*****
4. Enamelware
*****All pots and pans must have a magnetic bottom.*****
All pots and pans must have a flat bottom.
All pots and pans should have a diameter between 4.75” (12 cm) and 10.25” (26 cm).
UNSUITABLE POTS & PANS, - FOR INDUCTION HEATING PLATES
1. Pot with diameter below 2” (5 cm)
2. Stainless steel pans with aluminum bottom
3. Pottery
4. Glass pans
5. Aluminum pans
6. Bronze pans
7. Copper pots
8. Pans with feet
SAFETY DEVICES
Overtime Detector
If the pan is left on the induction cooker for more than 2 hours, or if the user does not operate any
functions for more than 2 hours, the cooker will automatically shutoff.
Automatic Safety Shut-Off
If the induction cooker is left on for more than 60 seconds without a pan or with an incompatible
pan, the unit will automatically shutoff.
Material Compatibility Detector
If the pan’s material or its dimensions are not suitable for this induction cooker, the “Heating
Indicator Light” will not turn on. The induction cooker will shutoff automatically after 60 seconds.
Small Object Detector
The induction cooker will not recognize any objects smaller than 2” (5 cm) in diameter. For best
results, use pans that are between 4.75” (12 cm) and 10.25” (26 cm) in diameter.
Over Heating Protection Device
If the pan’s temperature becomes too high, and the temperature remains too high for 60 seconds,
the unit will shut off automatically. There will be a short warning sound after the unit shutsoff.
HOW DOES YOUR INDUCTION HOB WORK?
A high frequency (20-35KHz) induction coil located underneath the ceramic top plate
heats the cooking pan by magnetic friction. The heat is produced directly within the pan.
It's controlled by an electronic circuit to offer superior performance and functions. During
cooking, no energy is lost between the hob and the food. When you switch it off, the
cooking is stopped immediately.
PRECAUTION BEFORE USING YOUR INDUCTION HOB
1. The glass top is made of strong, hard, and non-porous properties. But, in case of breakage,
even if it's only slightly cracked, disconnect the appliance from the electrical socket immediately
and contact the after-sales service.
2. The appliance is equipped with a Small Object Detector. It's recommended not to place small
metal kitchen utensils such as pan lids, knives, or other metal objects on the induction-heating
zone. If the inductor is switched on, there is a risk of them becoming hot.
3. When using your induction hob, don't place any magnetic sensitive objects on the glass top,
such as credit cards, cassettes, etc.
4. Scientific tests have shown that the induction hob presents no danger for anyone using a
pacemaker. Please keep a 2’ distance from the unit while the induction hob is in use.
5. To prevent from overheating, do not place aluminum foil or iron plate on the top plate.
6. Put the appliance on a horizontal surface but keep away from wall or articles at least 2” - 4”.
7. To prevent an electric shock, do not put articles like iron wire or tools into the air entrance or
outlet.
8. Immediate clean up is recommended when water is left on the top plate.
OPERATION INSTRUCTION
1. Plug power cord into 120V, 60Hz, 15A (IC-18A); 208V, 60Hz, 11A (IC-22A); 240V, 60Hz, 11A
(IC-25A) dedicated electrical circuit.
2. Turn power on by pressing the power on/off button.
3. Rotate the power control knob clockwise. The power level LED will display from level 1 (Min.) to
level 9 (Max.). If you turn past 9 it will start at 1 again. The same applies if you turn back past 1.
4. Put a suitable pan in center of the top plate, and rotate power control knob to desired power
level.
5. Heating Indicator Light indicates if the pan is suitable or not. If the Heating Indicator Light is
on, then the pan is heating. If the Heating Indicator Light is off, it means the power is on, but no
pan or suitable pan is on top plate.
6. This unit is equipped with an Over Heating Protection Device, which stops power temporarily
when top plate temperature reaches 482°F (+/- 10%). The power will start again automatically
when the temperature of the top plate is reduced below 482°F (+/- 10%). By heating an empty
pan, maximum temperature will be reached very quickly. The Heating Indicator Light will flash to
indicate the over heating protection function is on.
Temperature Hold function: By pressing the “Warm” function key, the Temperature Hold
function will start working. The LED indicates the temperature will hold at 140°F (+/- 5%), push
“Warm” function key again, the LED indicates the temperature will hold at 180°F. When the
“Warm” function key is pushed each time, the holding temperature will change as follows: 140°F
-> 180°F -> 285°F -> 360°F -> 430°F -> 140°F ->.
7. With the Temperature Hold function working, the “Warm” indicator light will start flashing. It
means the temperature has not yet arrived at the set temperature. When the pan’s temperature
arrives the set temperature, the “Warm” indicator light will stay on.
8. To change Temperature Hold function to “Heat” function: Push “Heat” function key, and the
function will go back to “Heat” again. Then the rotary control knob will be activated again.
7
8
3
2
Control Panel:
1
5
6
4
1. Power On/ Off Key
2. “Heating” Indicator Light
3. “Heat” Function Indicator Light
4. “Warm”(Hold Temperature) Function Indicator Light
5. “Warm”(Hold Temperature) Function Key
6. “Heat” Function Key
7. Power Level / Holding Temperature Display LED Lights
8. Power Regulator Rotary Knob
FEATURES & DESCRIPTION:
1
6
9
5
10
7
3
8
2
4
1. Induction Heating Zone
2. Ceramic Top Plate
3. Bottom Chassis
4. Rotary Control Knob (Power Regulator)
5. Induction Heating Indicator Light
6. Heat Function Indicator Light
7. “Warm” Function Indicator Light
8. Air-Intake
9. Air-Outlet
10. Foot Stand
Installation of the “Wall Stopper”
1. Find 2 steel bullets in the box. It’s the accessory for this induction
cooking plate.
2. Screw these 2 steel bullets into the rear side of top case and affix it
tightly.
3. The “Wall Stopper” functions as a “Stand-off”, allows the exhaust
fan, built into the unit, to operate properly. Improper mounting or
removal of this piece will cause the unit to operate improperly and
possibly overheat.
SPECIFICATION:
IC-18A
Model No.
Voltage
IC-22A
IC-25A
120V ~ 60Hz
208V ~ 60Hz
240V ~ 60Hz
Vitro-Ceramic Glass
Plate
Approx. 10.75” x 10.75”
Electrical Power
Consumption
Max. 1,800 watt
Max. 2,200 watt Max. 2,500 watt
Safety Device
Over Time Protector (2Hrs.)
Automatic Safety Shut-Off
Material Compatibility Detector
Small Object Detector
Overheating Protection Device
12.91” (32.8cm) x 16.73” (42.5 cm) x 4.33” (11 cm)
Dimension
TROUBLE SHOOTING
1. If your induction range seems to be working improperly, it doesn't necessarily mean it’s faulty. In
all cases, check the following points:
Problem
Resolution
No indicator light when power "on"
Cable/terminal block is loose
Broken circuit or blown fuse
Power supply stopped
Heating indicator does not light-up,
Appliance fails to heat up
Unsuitable cooking pan
Pan isn’t located in the center properly
Pan is smaller than 2”
Over-heating protection is activated
High temperature
Appliance suddenly stops heating
during operation
Air entrance or outlet blocked
Over-heating protection activated
2. If you fail to identify the problem, contact the after-sales service without delay.
Cecilware Corporation
43-05 20th Avenue
Long Island City, NY 11105
Tel: 800.935.2211, 718.932.1414
Fax: 718.932.7860
Technical Support
Customer Service:
|