NCCH-DR
Series
Contents
Notices................................................................................................ vi
Safety information ............................................................................. vii
About this guide ............................................................................... viii
Typography......................................................................................... ix
NCCH-DR Series specifications summary ............................................. x
Chapter 1: Product introduction
1.1
1.2
1.3
Welcome!.............................................................................. 1-1
Package contents ................................................................. 1-1
Special features.................................................................... 1-2
1.3.1
1.3.2
Product highlights................................................... 1-2
Innovative ASUS features ....................................... 1-4
Chapter 2: Hardware information
2.1
2.2
Before you proceed .............................................................. 2-1
Motherboard overview.......................................................... 2-2
2.2.1
2.2.2
2.2.3
2.2.4
2.2.5
Placement direction ................................................ 2-2
Screw holes ............................................................ 2-2
CPU heatsink weight support ................................. 2-3
Motherboard layout ................................................ 2-9
Layout contents ...................................................2-11
2.3
2.4
Central Processing Unit (CPU) ............................................2-13
2.3.1
2.3.2
Installling the CPU .................................................2-13
Installing the CPU heatsink(s)...............................2-15
System memory .................................................................2-16
2.4.1
2.4.2
2.4.3
2.4.4
Overview...............................................................2-16
Memory configurations .........................................2-16
Installing a DIMM ...................................................2-18
Removing a DIMM .................................................2-18
2.5
Expansion slots...................................................................2-19
2.5.1
2.5.2
2.5.3
2.5.4
Installing an expansion card..................................2-19
Configuring an expansion card..............................2-19
Interrupt assignments ..........................................2-20
PCI/PCI-X slots......................................................2-20
2.6.
2.7
Jumpers..............................................................................2-21
Connectors .........................................................................2-26
2.7.1
2.7.2
Rear panel connectors ..........................................2-26
Internal connectors...............................................2-27
iii
Contents
Chapter 3: Powering up
3.1
3.2
Starting up for the first time................................................ 3-1
Powering off the computer .................................................. 3-2
3.2.1
3.2.2
Using the OS shut down function ........................... 3-2
Using the dual function power switch .................... 3-2
Chapter 4: BIOS Setup
4.1
Managing and updating your BIOS ........................................ 4-1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
Creating a bootable floppy disk.............................. 4-1
AwardBIOS Flash Utility .......................................... 4-3
ASUS CrashFree BIOS 2 utility ................................ 4-7
ASUS EZ Flash utility .............................................. 4-9
ASUS Update utility ..............................................4-10
4.2
BIOS Setup program ...........................................................4-13
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
BIOS menu screen.................................................4-14
Menu bar...............................................................4-14
Navigation keys ....................................................4-14
General help ..........................................................4-15
Sub-menu .............................................................4-15
Scroll bar ..............................................................4-15
Pop-up window .....................................................4-15
4.3
4.4
Main menu ..........................................................................4-16
4.3.1
4.3.2
4.3.3
4.3.4
Primary IDE Master ...............................................4-17
Primary IDE Slave ..................................................4-19
Secondary IDE Master...........................................4-19
Secondary IDE Slave .............................................4-19
Advanced menu..................................................................4-20
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
Advanced BIOS Features ......................................4-21
CPU Configuration.................................................4-22
Memory Configuration ..........................................4-23
Chipset .................................................................4-24
Onboard Device ....................................................4-25
PCIPnP...................................................................4-29
USB Configuration.................................................4-31
4.5
Power menu........................................................................4-32
4.5.1
4.5.2
APM Configuration ................................................4-33
Hardware Monitor .................................................4-36
i v
Contents
4.6
Boot menu ..........................................................................4-38
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.6.6
Boot Device Priority..............................................4-38
Hard Disk Boot Priority .........................................4-39
Removable Device Priority ....................................4-39
CD-ROM Boot Priority ...........................................4-40
Boot Settings Configuration .................................4-40
Security ................................................................4-42
4.7
Exit menu ...........................................................................4-44
Appendix: Reference information
A.1
NCCH-DR block diagram .......................................................A-1
v
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics
card is required to assure compliance with FCC regulations. Changes or
modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
v i
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing
system before you add a device.
• Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
• Seek professional assistance before using an adpater or extension cord.
These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you are
using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read
all the manuals that came with the package.
•
Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
•
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
vii
About this guide
This user guide contains the information you need when installing and
configuring the motherboard.
How this guide is organized
This manual contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
•
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to
perform when installing system components. It includes description of
the switches, jumpers, and connectors on the motherboard.
•
•
Chapter 3: Powering up
This chapter describes the power up sequence, the vocal POST
messages, and ways of shutting down the system.
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS
Setup menus. Detailed descriptions of the BIOS parameters are also
provided.
•
Appendix: Reference information
This appendix includes additional information that you may refer to
when configuring the motherboard.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1 . ASUS websites
The ASUS website provides updated information on ASUS hardware
and software products. Refer to the ASUS contact information.
2 . Optional documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
viii
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1+Key2+Key3>
If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command exactly as shown,
then supply the required item or value enclosed in
brackets.
Example: At the DOS prompt, type the command line:
afudos /i[filename]
afudos /iNCCH-SR.ROM
i x
NCCH-DR Series specifications summary
CPU
Support for dual Intel® Xeon™ Processors up to 4.4+ GHz
with Hyper-Threading Technology
Support for Extended Memory 64-bit Technology (EM64T)
On-die 1MB L2 cache
Chipset
North bridge: Intel® E7210 Memory Controller Hub (MCH)
South bridge: Intel® 6300ESB I/O Controller Hub (ICH)
Front Side Bus
Memory
800 MHz
Dual-channel memory architecture
4 x 184-pin DDR DIMM sockets for up to 4GB memory
Supports PC3200/PC2700 unbuffered ECC or non-ECC
DDR DIMMs
Expansion slots
Storage
1 x PCI-X 66 MHz/64-bit slot (supports ZCR, PCI-X 1.0)
1 x PCI-X 66 MHz/64-bit slot (PCI-X 1.0)
3 x PCI 33 MHz/32-bit slot (PCI 2.3)
IDE model
Intel® 6300ESB South Bridge supports:
- 2 x UltraDMA100/66/33
- 2 x Serial ATA 150 connectors that support
RAID 0, RAID 1 configurations, and the Intel® Matrix
Storage Technology
SATA model
IDE model storage + Adaptec® AIC-8130 PCI-X SATA-II
controller that supports:
- 4 x SATA-II connectors (300 Mbps)
- RAID 0, RAID 1, or RAID 0+1 configurations
- Zero-Channel RAID (optional)
LAN
Intel® PRO/1000 CT Network Connection (82547GI)
Intel® PRO/1000 MT Network Connection (82541GI)
USB
USB 2.0 (480 Mbps) / 1.1 (12 Mbps)
BIOS features
8Mb Flash ROM, Award BIOS, PnP, DMI, WfM2.0,
SM BIOS2.3
Rear panel
1 x PS/2 keyboard port
1 x PS/2 mouse port
2 x USB 2.0 ports
1 x Serial port
1 x Video port
2 x Gigabit LAN (RJ-45) ports
(continued on the next page)
x
NCCH-DR Series specifications summary
Internal
connectors
Floppy disk drive connector
IDE connectors
Serial ATA connectors
Serial ATA RAID connectors (SATA models only)
Hard disk activity LED connector
CPU and system fan connectors
USB port connector
SSI power connectors
Serial port connector
Printer port connector
Backplane SMBus connector
Power supply SMBus connector
BMC connector
Auxiliary panel connector
System panel connector
Industry
standard
PCI 2.3, PCI-X 1.0, USB 2.0
Manageability
WfM 2.0. DMI 2.0, WOL/WOR by PME, chassis intrusion
SSI-type power supply (with 24-pin and 8-pin power plugs)
Power
Requirement
Form Factor
Extended ATX form factor: 12 in x 10.5 in
(30.5 cm x 26.7 cm)
Innovative ASUS
features
ASUS CrashFree BIOS 2
ASUS Q-Fan 2
ASUS EZFLash
ASUS MyLogo 2
Support CD
contents
Device drivers
ASUS Server Web-based Management (ASWM) software
System utilities
ASUS contact information
*Specifications are subject to change without notice.
x i
xii
This chapter describes the motherboard
features and the new technologies
it supports.
Product
1
introduction
Chapter summary
1
1.1
1.2
1.3
Welcome!.............................................................................. 1-1
Package contents ................................................................. 1-1
Special features.................................................................... 1-2
ASUS NCCH-DR
1.1 Welcome!
Thank you for buying the ASUS® NCCH-DR motherboard!
The ASUS NCCH-DR motherboard delivers a host of new features and latest
technologies making it another standout in the long line of ASUS quality
motherboards!
Before you start installing the motherboard, and hardware devices on it,
check the items in your package with the list below.
1.2 Package contents
Check your motherboard package for the following items.
Motherboard
Cables
ASUS NCCH-DR motherboard
IDE model:
2 x Serial ATA signal cables
1 x Serial ATA power cables (dual-plug)
1 x Ultra DMA 100/66 IDE and floppy drive cable (3-in-1)
SATA model:
6 x Serial ATA signal cables
3 x Serial ATA power cables (dual-plug)
1 x Ultra DMA 100/66 IDE and floppy drive cable (3-in-1)
I/O module
Accessories
Printer port module
I/O shield
X-PAD accessory kit
2 x CEK spring
Application CDs ASUS motherboard support CD (includes ASWM)
Documentation User guide
If any of the above items is damaged or missing, contact your retailer.
ASUS NCCH-DR
1-1
1.3 Special features
1.3.1 Product highlights
Latest processor technology
The motherboard comes with dual 604-pin surface mount ZIF sockets
designed for the Intel® Xeon™ processor with 800 MHz Front Side Bus
(FSB) and 1 MB L2 cache. The processor incorporates the Intel®
Hyper-Threading Technology, the Intel® NetBurst™ micro-architecture that
features hyper-pipelined technology, and Extended Memory 64-bit
Technology (EM64T). The EM64T enables the support for 64-bit operation
system, such as 64-bit Windows® and Linux. See page 2-13 for details.
Intel® E7210 and Intel® 6300 ESB chipset
The Intel® E7210 Memory Controller Hub (MCH) and the Intel® 6300ESB I/O
controller hub (ICH) provide the vital interfaces for the motherboard.
The MCH provides the processor, dual-channel DDR400 memory, and CSA
interfaces. The ICH is a new generation server class I/O controller hub that
provides the interface for PCI-X 1.0a and other interfaces.
Dual-channel memory support
Employing the dual-channel DDR memory architecture, the motherboard
provides a solution that doubles the system memory bandwidth to boost
system performance. The motherboard supports up to 4 GB of system
memory using PC3200/PC2700 ECC or non-ECC DDR DIMMs to deliver up to
6.4 GB/s data transfer rate for the latest 3D graphics, multimedia, and
Internet applications. See page 2-16 for details.
Serial ATA technology
The motherboard supports the Serial ATA technology through the Serial
ATA interfaces controlled by the Intel® 6300ESB and the Adaptec AIC-
8130 PCI-X SATA-II controller (on SATA models only). The SATA
specification allows for thinner, more flexible cables with lower pin count,
reduced voltage requirement, and up to 150 MB/s data transfer rate for
6300ESB and 300 MB/s for AIC-8130. See page 2-28 to 2-29 for details.
Built-in SATA RAID solution
The Intel® 6300ESB allows RAID 0 and RAID 1 configuration for two SATA
connectors and supports the Intel® Matrix Storage Technology. See page
2-28 for details.
For SATA models, the Adaptec AIC-8130 PCI-X SATA-II (300 Mbps)
controller supports four additional SATA connectors, and allows RAID 0,
RAID 1, and RAID 0+1 configuration. See page 2-29 for details.
1-2
Chapter 1: Product introduction
Dual Gigabit LAN solution
The Intel® PRO/1000 CT Network Connection allows full-duplex Gigabit
performance on LAN on Motherboard (LOM) applications through the
Communication Streaming Architecture (CSA). Instead of connecting to the
PCI bus, the controller connects to the dedicated CSA bus on the Memory
Controller Hub (MCH) thus reducing the PCI bottlenecks by freeing the PCI
bus for other I/O operations.
The Intel® PRO/1000 MT Network Connection is also onboard to support
32-bit LAN through the PCI bus. See page 2-26 for details.
Zero-Channel RAID (ZCR) solution (on SATA models only)
The Adaptec AIC-8130 PCI-X SATA-II controller also supports an optional
Zero-Channel RAID card on the 64-bit PCI-X slot to create a RAID solution,
including RAID 0 (striping), RAID 1 (mirroring), RAID 0+1, and RAID 5. The
ZCR capability provides a cost-effective, high-performance RAID sets.
Integrated graphics
The onboard ATI Rage™ XL graphics controller with 8MB memory provides a
reliable graphics solution for server applications. See page 2-26 for details.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0
specification, dramatically increasing the connection speed from the
12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is
backward compatible with USB 1.1. See page 2-26 and 2-30 for details.
Temperature, fan, and voltage monitoring
The CPU temperature is monitored by the ASIC (integrated in the Winbond
Super I/O) to prevent overheating and damage. The system fan rotations
per minute (RPM) is monitored for timely failure detection. The ASIC
monitors the voltage levels to ensure stable supply of current for critical
components. See page 4-36 and 4-37 for details.
ASUS NCCH-DR
1-3
1.3.2 Innovative ASUS features
ASUS CrashFree BIOS 2
This feature allows you to restore the original BIOS data from the support CD
in case when the BIOS codes and data are corrupted. This protection
eliminates the need to buy a replacement ROM chip. See page 4-7 for details.
ASUS EZ Flash BIOS
With the ASUS EZ Flash, you can easily update the system BIOS even
before loading the operating system. No need to use a DOS-based utility or
boot from a floppy disk. See page 4-9 for details.
ASUS Q-Fan 2 technology
The ASUS Q-Fan 2 technology smartly adjusts the fan speeds according to
the system loading to ensure quiet, cool, and efficient operation. See page
4-37 for details.
ASUS MyLogo2™
This new feature present in the motherboard allows you to personalize and
add style to your system with customizable boot logos. See page 4-40 for
details.
1-4
Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components.
It includes description of the jumpers
and connectors on the motherboard.
Hardware
2
information
Chapter summary
2
2.1
2.2
2.3
2.4
2.5
2.6.
2.7
Before you proceed .............................................................. 2-1
Motherboard overview.......................................................... 2-2
Central Processing Unit (CPU) ............................................2-13
System memory .................................................................2-16
Expansion slots...................................................................2-19
Jumpers ..............................................................................2-21
Connectors .........................................................................2-26
ASUS NCCH-DR
2.1 Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
•
•
Unplug the power cord from the wall socket before touching any
component.
Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
Before you install or remove any component, ensure
that the power supply is switched off or the power
cord is detached from the power supply. Failure to do so
may cause severe damage to the motherboard, peripherals, and/or
components.
Onboard LED
The motherboard comes with a standby power LED. The green LED lights
up to indicate that the system is ON, in sleep mode, or in soft-off mode.
This is a reminder that you should shut down the system and unplug the
power cable before removing or plugging in any motherboard component.
The illustration below shows the location of the onboard LED.
SB_PWR1
ON
OFF
Standby
Power
Powered
Off
NCCH-DR
NCCH-DR Onboard LED
ASUS NCCH-DR
2-1
2.2 Motherboard overview
Before you install the motherboard, study the configuration of your chassis
to ensure that the motherboard fits into it.
Make sure to unplug the chassis power cord before installing or removing
the motherboard. Failure to do so can cause you physical injury and
damage motherboard components.
2.2.1 Placement direction
When installing the motherboard, make sure that you place it into the
chassis in the correct orientation. The edge with external ports goes to the
rear part of the chassis as indicated in the image below.
2.2.2 Screw holes
Place nine (9) screws into the holes indicated by circles to secure the
motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
NCCH-DR
2-2
Chapter 2: Hardware information
2.2.3 CPU heatsink weight support
For additional protection from motherboard breakage due to the weight of
the CPU heatsinks, your motherboard package comes with two solution kits.
• X-PAD accessory kit containing:
– 2 x metal support plates
– 1 x contour sheet
– 3 different sets of metal nuts and rubber pads for varied chassis
standoffs (each set contains 8 metal nuts and 2 rubber pads)
• 2 x CEK spring
You can use any of the two solutions to protect the motherboard.
Using the X-PAD accessory kit
To install the support plates:
1. Open and lay your system
chassis on a stable surface, then
locate the motherboard
standoffs.
Standoff
Standoff beside
power supply
2. Align the holes of the contour
sheet with the standoffs on the
base of the chassis. Press the
sheet flat making sure that it is
completely pressed against to
the chassis.
The contour sheet fits in only
one orientation. Make sure
that the hole located about
1 cm from the corner
matches the standoff beside
the power supply.
3. Determine the height of the standoffs on your chassis, and select the
appropriate set of metal nuts and rubber pads from your package.
Use a nut size that is slightly lower than the standoffs on your chassis.
ASUS NCCH-DR
2-3
4. Use a plier to attach four nuts to
the bolts on the metal support
plate.
5. Align a rubber pad to the
rectagular mark on the center of
the plate, then press to attach.
6. Remove the adhesive label
underneath a plate.
2-4
Chapter 2: Hardware information
7. Carefully align and place the
plate on a rectangular cut on the
contour sheet.
Make sure that the metal support plates fit perfectly to the rectangular
cuts on the contour sheet; otherwise, the CPU heatsink screws would
not align to the metal nuts.
8. Repeat steps 4 and 7 to prepare
and install the second plate.
9. Remove the contour sheet from
the chassis.
ASUS NCCH-DR
2-5
The support plates appear as
shown when installed.
9. Install the motherboard with the
external I/O ports toward the
chassis rear panel. The CPU
sockets should be right on top
of the support plates.
Heatsink hole matched to
a nut on the support plate
Make sure that the CPU heatsink holes on the motherboard perfectly
match the metal nuts on the support plates; otherwise, you can not
install the CPU heatsinks properly.
10. Secure the motherboard with 9 screws. Refer to section “2.2.2 Screw
holes” for illustration.
2-6
Chapter 2: Hardware information
Using the CEK springs
Two CEK springs come with the
motherboard package. You can also
use these springs to support the
weight of the CPU heatsinks. Take
note of the four CEK spring hooks
located beside the screw holes.
CEK spring hook
To install the CEK spring:
1. Locate the CPU heatsink holes
on the motherboard.
2. Position the CEK spring
underneath the motherboard,
then match the CEK spring
hooks to the CPU1 heatsink
holes.
3. Press the upper spring hooks
inward, then insert to the upper
CPU heatsink holes until they
snap in place.
ASUS NCCH-DR
2-7
4. Press the lower spring hooks
inward, then insert to the lower
CPU heatsink holes until they
snap in place.
5. Repeat the process to install the
second spring to the CPU2
heatsink holes.
The support plates appear as
shown when installed.
6. Install the motherboard with the
external I/O ports toward the
chassis rear panel. The CPU
sockets should be right on top
of the CEK springs.
Heatsink hole matched to
the hole on the CEK spring
7. Secure the motherboard with 9 screws. Refer to section “2.2.2 Screw
holes” for illustration.
2-8
Chapter 2: Hardware information
2.2.4 Motherboard layout
IDE model
26.8cm (10.5in)
ATX12V1
PS/2KBMS
T: Mouse
B: Keyboard
ATXPWR1
KBPWR1
PSUSMB1
USBPW12
USB12
REAR_FAN2
LAN_EN1
Intel
82547GI
Gigabit
CPU2
Intel
MCH
E7210
Ethernet
CPU_FAN2
FM_CPU2
DDR DIMM_A1 (64 bit,184-pin module)
DDR DIMM_A2 (64 bit,184-pin module)
LAN1
LAN2
DDR DIMM_B1 (64 bit,184-pin module)
DDR DIMM_B2 (64 bit,184-pin module)
CPU1
SB_PWR1
REAR_FAN1
CPU_FAN1
FM_CPU1
PCIX1 (64-bit, 66MHz 3V)
PCIX2 (64-bit, 66MHz 3V)
Intel
82541GI
Gigabit
Ethernet
FRNT_FAN2
FRNT_FAN1
LAN_EN2
PCI3 (32-bit, 33MHz 5V)
ATI
RAGE XL
VGA
SATA2
PCI4 (32-bit, 33MHz 5V)
PCI5 (32-bit, 33MHz 5V)
Intel
ICH
Controller
VGA_EN1
6300ESB
SATA1
Super
I/O
USB34
USBPW34
SEC_IDE
PRI_IDE
CR2032 3V
AUX_PANEL1
HDLED
Lithium Cell
CMOS Power
BMCCONN1
BPSMB1
FLOPPY
CLRTC1
RECOVERY
LPT1
COM2
PANEL1
NCCH-DR
ASUS NCCH-DR
2-9
SATA model
26.8cm (10.5in)
ATX12V1
PS/2KBMS
T: Mouse
B: Keyboard
ATXPWR1
KBPWR1
PSUSMB1
USBPW12
USB12
REAR_FAN2
LAN_EN1
Intel
82547GI
Gigabit
CPU2
Intel
MCH
E7210
Ethernet
CPU_FAN2
FM_CPU2
DDR DIMM_A1 (64 bit,184-pin module)
DDR DIMM_A2 (64 bit,184-pin module)
LAN1
LAN2
DDR DIMM_B1 (64 bit,184-pin module)
DDR DIMM_B2 (64 bit,184-pin module)
CPU1
SB_PWR1
REAR_FAN1
CPU_FAN1
FM_CPU1
PCIX1 (64-bit, 66MHz 3V)
PCIX2 (64-bit, 66MHz 3V)
Intel
82541GI
Gigabit
Ethernet
FRNT_FAN2
FRNT_FAN1
LAN_EN2
Adaptec
AIC-8130
PCI3 (32-bit, 33MHz 5V)
ATI
RAGE XL
VGA
SATA2
PCI4 (32-bit, 33MHz 5V)
PCI5 (32-bit, 33MHz 5V)
Intel
ICH
Controller
VGA_EN1
6300ESB
SATA1
SATA_EN1
Super
I/O
USB34
USBPW34
SEC_IDE
PRI_IDE
CR2032 3V
AUX_PANEL1
Lithium Cell
CMOS Power
BMCCONN1
BPSMB1
HDLED
RECOVERY
PANEL1
FLOPPY
CLRTC1
8130 LED1
LPT1
COM2
NCCH-DR
2-10
Chapter 2: Hardware information
2.2.5 Layout contents
Slots
Page
2-13
2-16
2-20
1. CPU sockets
2. DDR DIMM sockets
3. PCI/PCI-X slots
Jumpers
Page
2-21
2-22
2-22
2-23
2-23
2-24
2-24
2-25
2-25
Clear RTC RAM (CLRTC1)
CPU fan pin selection (3-pin FM_CPU1, FM_CPU2)
USB device wake-up (3-pin USBPW12, USBPW34)
Keyboard power (3-pin KBPWR1)
SATA controller setting (3-pin SATA_EN1) SATA models only
SATA controller LED setting (3-pin 8130LED1) SATA models only
Gigabit LAN controller setting (3-pin LAN_EN1; LAN_EN2)
Integrated graphics controller (3-pin VGA_EN1)
Force BIOS recovery (3-pin RECOVERY)
Rear panel connectors
1. PS/2 mouse port (green)
2. PS/2 keyboard port (purple)
3. USB 2.0 ports 1 and 2
4. Serial (COM1) port
5. VGA port
Page
2-26
2-26
2-26
2-26
2-26
2-26
2-26
6. LAN1 (RJ-45) port
7. LAN2 (RJ-45) port
ASUS NCCH-DR
2-11
Internal connectors
P
a
g
e
Floppy disk drive connector (34-1 pin FLOPPY)
IDE connectors (40-1 pin PRI_IDE, SEC_IDE)
Serial ATA connectors (7-pin SATA1, SATA2)
2-27
2-27
2-28
2-29
Serial ATA RAID connectors (7-pin SATA_RAID1, SATA_RAID2,
SATA_RAID3, SATA_RAID4) SATA models only
Hard disk activity LED connector (2-pin HDLED)
2-29
2-30
CPU and system fan connectors (4-pin CPU_FAN1/2,
3-pin REAR_FAN1/2, FRNT_FAN1/2)
USB port connector (10-1 pin USB34)
2-30
2-31
2-32
2-32
2-33
2-33
2-34
2-34
SSI power connectors (24-pin ATXPWR1, 8-pin ATX12V1)
Serial port connector (10-1 pin COM2)
Printer port connector (26-1 pin LPT1)
Backplane SMBus connector (6-1 pin BPSMB1)
Power supply SMBus connector (5-pin PSUSMB1)
BMC connector (16-pin BMCCONN1)
Auxiliary panel connector (20-2 pin AUX_PANEL1)
System panel connector (20-pin PANEL1)
System power LED (Green 3-pin PLED)
2-35
2-35
2-35
2-35
2-35
2-35
2-35
Message LED (Brown 2-pin MLED)
Hard disk drive activity LED (Red 2-pin HDD_LED)
System warning speaker (Orange 4-pin SPEAKER)
ATX power button/soft-off button (Yellow 2-pin PWRSW)
Reset button (Blue 2-pin RESET)
2-12
Chapter 2: Hardware information
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount 604-pin Zero Insertion Force
(ZIF) sockets. The sockets are designed for the Intel® Xeon™ processor in
the 604-pin package with 1 MB L2 cache. The new generation Xeon™
processor supports 800 MHz system bus and EM64T.
2.3.1 Installling the CPU
To install a CPU:
1. Locate the CPU sockets on the motherboard.
Intel Xeon
Gold Arrow
CPU2
Pin A1
CPU1
NCCH-DR
NCCH-DR CPU Socket 604
If installing only one CPU, use the socket CPU1.
2. Flip up the socket lever and push
it all the way to the other side.
Make sure that the socket
lever is pushed back all the
way, otherwise the CPU does
not fit in completely.
Socket for CPU1
ASUS NCCH-DR
2-13
3. Position the CPU above the
socket as shown.
4. Carefully insert the CPU into the
socket until it fits in place.
The CPU fits only in one
correct orientation. DO NOT
force the CPU into the socket
to prevent bending the pins
and damaging the CPU!
Marked corner
(gold arrow)
5. Carefully push down the socket
lever to secure the CPU. The
lever clicks on the side tab to
indicate that it is locked.
6. Apply the thermal interface
material (thermal grease) to the
top of the CPU. This thermal
grease should come with the
CPU package.
7. Repeat steps 1 to 6 if you wish
to install a second CPU.
2-14
Chapter 2: Hardware information
2.3.2 Installing the CPU heatsink(s)
The Intel® Xeon™ processors require specially-designed passive heatsinks to
provide optimum thermal condition and performance. Visit the ASUS
website (www.asus.com) for an updated list of qualified heatsinks tested
for use on this motherboard.
Make sure that you have applied the thermal grease to the top of the
CPU before installing the heatsink.
To install the CPU heatsink and fan:
1. Place the heatsink on top of the
installed CPU, making sure that
the four screws on the heatsink
align with the nuts on the
support plate or with the holes
of the CEK spring.
2. Use a Phillips screwdriver to
tighten the four heatsink screws
in a diagonal sequence.
3. Repeat the process to install the
second heatsink on top of the
second CPU, if any.
ASUS NCCH-DR
2-15
2.4 System memory
2.4.1 Overview
The motherboard comes with four Double Data Rate (DDR) Dual Inline
Memory Modules (DIMM) sockets.
The following figure illustrates the location of the DDR DIMM sockets:
104 Pins
80 Pins
DIMM_A1
DIMM_A2
DIMM_B1
NCCH-DR
DIMM_B2
NCCH-DR 184-Pin DDR DIMM sockets
2.4.2 Memory configurations
You may install 128 MB, 256 MB, 512 MB and 1 GB unbuffered ECC or
non-ECC DDR DIMMs into the DIMM sockets.
•
•
Installing DDR DIMMs other than the recommended configurations
may cause memory sizing error or system boot failure. Use any of
the recommended configurations in Table 1.
Always install DIMMs with the same CAS latency. For optimum
compatibility, it is recommended that you obtain memory modules
from the same vendor. Refer to the DDR Qualified Vendors List on
the the ASUS website for details.
•
•
In dual-channel configurations, install only identical (the same type
and size) DDR DIMM pairs on each channel.
Due to chipset resource allocation, the system may detect less than
4 GB system memory when you installed four 1 GB DDR memory
modules.
•
Three DDR DIMMs installed into any three memory sockets will
function in single-channel mode.
2-16
Chapter 2: Hardware information
Table 1: Recommended memory configurations
Sockets
Mode
DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2
(black)
(blue)
(black)
(blue)
Single-channel
(1)
(2)
(3)
(4)
(1)
(2)
Populated
—
Populated
—
—
—
—
—
(DDR400/DDR333)
—
—
—
Populated
—
—
—
Populated
—
Dual-channel
Populated
—
—
Populated
—
(DDR400/DDR333)
Populated
Populated
(3)* Populated Populated Populated Populated
* For dual-channel configuration (3), you may:
• install identical DIMMs in all four sockets, or
• install identical DIMMs in DIMM_A1 and DIMM_B1 (black sockets)
and identical DIMMs in DIMM_A2 and DIMM_B2 (blue sockets)
ASUS NCCH-DR
2-17
2.4.3 Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both
the motherboard and the components.
DDR DIMM
notch
To install a DIMM:
1. Unlock a DIMM socket by
pressing the retaining clips
outward.
2. Align a DIMM on the socket
such that the notch on the
DIMM matches the break on the
socket.
Unlocked retaining clip
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
3. Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
Locked retaining clip
2.4.4 Removing a DIMM
Follow these steps to remove a DIMM.
1. Simultaneously press the
retaining clips outward to unlock
the DIMM.
Support the DIMM lightly with
your fingers when pressing the
retaining clips. The DIMM
might get damaged when it
flips out with extra force.
2. Remove the DIMM from the socket.
2-18
Chapter 2: Hardware information
2.5 Expansion slots
In the future, you may need to install expansion cards. The following
sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage motherboard components.
2.5.1 Installing an expansion card
To install an expansion card:
1. Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already
installed in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep
the screw for later use.
4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.5.2 Configuring an expansion card
After installing the expansion card, configure the it by adjusting the
software settings.
1. Turn on the system and change the necessary BIOS settings, if any.
See Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments. Otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable.
ASUS NCCH-DR
2-19
2.5.3 Interrupt assignments
Standard interrupt assignments
I R Q
Priority
Standard Function
0
1
1
2
System Timer
Keyboard Controller
2
3
4
5
6
7
8
9
10
11
12
13
14
15
—
11
12
13
14
15
3
4
5
6
7
Re-direct to IRQ#9
Communications Port (COM2)*
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
Printer Port (LPT1)*
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE Channel
8
9
10
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
P X P X P X P X
IRQ1 IRQ2 IRQ3 IRQ4
A
B
C
D
E
F
G
H
PCI-X1 slot
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
shared shared shared shared
shared shared shared shared
PCI-X2 slot
PCI slot1
—
—
shared shared shared shared
shared shared shared shared
shared shared shared shared
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
PCI slot2
—
—
PCI slot3
—
—
—
Onboard USB controller 1
Onboard USB controller 2
Onboard USB 2.0 controller
Onboard SATA controller
Onboard LAN2
shared
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
shared
—
—
—
shared
—
—
—
—
shared
shared
—
—
—
2.5.4 PCI/PCI-X slots
The PCI/PCI-X slots support cards
such as a LAN card, SCSI card, USB
card, and other cards that comply
with PCI 2.3 and PCI-X 1.0
specifications. The figure shows a
LAN card installed on a PCI slot.
The PCI-X1 slot on SATA models is colored green. When installing a
Zero-Channel RAID card, it is recommended that you install it on the
PCI-X1 slot for optimum compatibility and performance.
2-20
Chapter 2: Hardware information
2.6. Jumpers
1 . Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The onboard
button cell battery powers the RAM data in CMOS, which include
system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the
cap on pins 2-3 for about 5~10 seconds, then move the cap back
to pins 1-2.
4. Re-install the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC
jumper default position. Removing the cap will cause system boot failure!
CLRTC1
2 1
3 2
NCCH-DR
Normal
(Default)
Clear CMOS
NCCH-DR Clear RTC RAM
ASUS NCCH-DR
2-21
2 . CPU fan pin selection (3-pin FM_CPU1, FM_CPU2)
These jumpers allow you to connect either a 3-pin or a 4-pin CPU fan
cable plug to the CPU fan connectors (CPU_FAN1, CPU_FAN2). Set
these jumpers to pins 1-2 if you are using a 3-pin fan cable plug, or to
pins 2-3 if you are using a 4-pin plug.
FM_CPU2
3
2
1
2
DC mode
(Default)
PWM
FM_CPU1
1 2
2 3
DC mode
(Default)
PWM
NCCH-DR
NCCH-DR FM_CPU Setting
3 . USB device wake-up (3-pin USBPW12, USBPW34)
Set these jumpers to +5V to wake up the computer from S1 sleep
mode (CPU stopped, DRAM refreshed, system running in low power
mode) using the connected USB devices. Set to +5VSB to wake up
from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh,
power supply in reduced power mode).
USBPW12
1 2
2 3
+5V
+5VSB
(Default)
USBPW34
1 2
2 3
+5V
+5VSB
NCCH-DR
NCCH-DR USB device wake-up (Default)
•
•
The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the
system would not power up.
The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
2-22
Chapter 2: Hardware information
4 . Keyboard power (3-pin KBPWR1)
This jumper allows you to enable or disable the keyboard wake-up
feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer
when you press a key on the keyboard (the default is the Space Bar).
This feature requires an ATX power supply that can supply at least 1A
on the +5VSB lead, and a corresponding setting in the BIOS.
KBPWR1
1 2
2 3
+5V
(Default)
+5VSB
NCCH-DR
NCCH-DR Keyboard power setting
5. SATA controller setting (3-pin SATA_EN1) On SATA models only
These jumpers allow you to enable or disable the onboard Adaptec®
AIC-8130 SATA RAID controller. Set to pins 1-2 to activate the SATA
controller.
SATA_EN1
3
2
1
2
Enable
(Default)
Disable
NCCH-DR
NCCH-DR SATA_EN setting
ASUS NCCH-DR
2-23
6 . SATA controller LED setting (3-pin 8130LED1)
This jumper allows you to enable or disable the SATA controller LED
indicator in the chassis front panel.
HDLED
RECOVERY
8130 LED1
PANEL1
8130 LED1
1 2
2 3
Disable
(Default)
Enable
NCCH-DR
NCCH-DR 8130 LED setting
7 . Gigabit LAN controller setting
(3-pin LAN_EN1; LAN_EN2)
These jumpers allow you to enable or disable the onboard Gigabit LAN
controllers. The LAN_EN1 jumper is for the Intel® 82547GI Gigabit
LAN controller (CSA) that controls the LAN1 port. The LAN_EN2
jumper is for the Intel® 82541GI Gigabit LAN controller (32-bit) that
controls the LAN2 port. Place the jumper caps on pins 1-2 to activate
the Gigabit LAN controller.
LAN_EN1
1 2
2 3
Enable
(Default)
Disable
NCCH-DR
NCCH-DR LAN_EN1 setting
LAN_EN2
1 2
2 3
Enable
(Default)
Disable
NCCH-DR
NCCH-DR LAN_EN2 setting
2-24
Chapter 2: Hardware information
8 . Integrated graphics controller (3-pin VGA_EN1)
This jumper allows you enable or disable the onboard graphics
controller.
VGA_EN1
1 2
2 3
Enable
(Default)
Disable
NCCH-DR
NCCH-DR VGA Setting
9 . Force BIOS recovery (3-pin RECOVERY)
This jumper allows you to update or recover the BIOS settings when it
gets corrupted or destroyed.This jumper allows you to update/recover
the BIOS quickly.
To update the BIOS:
1.
Prepare a floppy disk that contains the latest BIOS for the
motherboard (xxxx-xxx.BIN) and the AWDFLASH.EXE utility.
2.
3.
4.
5.
6.
Set the jumper to pins 2-3.
Insert the floppy disk, then turn on the system to update the BIOS.
Shut down the system.
Set the jumper back to pins 1-2.
Turn on the system.
LED
RECOVERY
0 LED1
PANEL1
RECOVERY
1 2
2 3
Normal
BIOS Recovery
(Default)
NCCH-DR
NCCH-DR BIOS recovery setting
ASUS NCCH-DR
2-25
2.7 Connectors
2.7.1 Rear panel connectors
1
2
3
4
5
6
7
1. PS/2 mouse port (green). This port is for a PS/2 mouse.
2. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
3. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
4. Serial (COM1) port. This 9-pin communication port is for pointing
devices or other serial devices.
5. VGA port. This port is for a VGA monitor.
6. LAN1 (RJ-45) port. Controlled by the Intel® 82547GI Gigabit LAN
controller (CSA), this port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for
the LAN port LED indications.
7. LAN2 (RJ-45) port. Controlled by the Intel® 82541GI Gigabit LAN
controller (32-bit), this port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for
the LAN port LED indications.
LAN port LED indications
ACT/LINK SPEED
ACT/LINK LED
Status Description
SPEED LED
L E D
L E D
Status
OFF
Description0
10 Mbps connection
OFF
No link
Linked
GREEN
BLINKING
ORANGE 100 Mbps connection
1 Gbps connection
Data activity GREEN
LAN port
2-26
Chapter 2: Hardware information
2.7.2 Internal connectors
1 . Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using a FDD cable with a covered Pin 5.
FLOPPY
PIN 1
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
NCCH-DR
NCCH-DR Floppy disk drive connector
2 . IDE connectors (40-1 pin PRI_IDE, SEC_IDE)
These connectors are for Ultra DMA 100/66/33 signal cables. The Ultra
DMA 100/66/33 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for an
Ultra DMA 100/66/33 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66/33 IDE master device
(hard disk drive). If you install two hard disk drives, you must configure
the second drive as a slave device by setting its jumper accordingly.
Refer to the hard disk documentation for the jumper settings.
•
Pin 20 on the IDE connectors are removed to match the covered
hole on the Ultra DMA cable connector. This prevents incorrect
insertion when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66/33 IDE devices.
SEC_IDE
PIN 1
PRI_IDE
PIN 1
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
NCCH-DR
NCCH-DR IDE connectors
ASUS NCCH-DR
2-27
3 . Serial ATA connectors (7-pin SATA1, SATA2)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Intel® Matrix Storage Technology
through the onboard Intel® 6300ESB integrated RAID controller.
These connectors are set to Standard IDE mode by default. In
Standard IDE mode, you can connect Serial ATA boot/data hard disk
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the SATA Mode item in the BIOS to [RAID].
See page 4-27 and 4-28 for details.
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
NCCH-DR
RSATA_RXP1
GND
NCCH-DR SATA connectors
Important notes on Serial ATA
•
You must install Windows® 2000 Service Pack 4 or the Windows® XP
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1) is available only if you are using
Windows® 2000/XP.
•
•
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
When using the connectors in IDE mode, connect the primary (boot)
hard disk drive to the SATA1 or SATA2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Connector
Setting
U s e
SATA1
SATA2
Master
Slave
Boot disk
Data disk
2-28
Chapter 2: Hardware information
4. Serial ATA RAID connectors (7-pin SATA_RAID1,
S ATA_RAID2, SATA_RAID3, SATA_RAID4) On SATA models only
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the Adaptec AIC-8130 SATA RAID controller.
SATA_RAID4
GND
RSATA_TXP6
RSATA_TXN6
GND
RSATA_RXN6
RSATA_RXP6
GND
SATA_RAID3
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXN5
RSATA_RXP5
GND
SATA_RAID2
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXN4
RSATA_RXP4
GND
SATA_RAID1
NCCH-DR
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXN3
RSATA_RXP3
GND
NCCH-DR SATA RAID connectors
Before creating a RAID set using Serial ATA hard disks, make sure that
you have connected the Serial ATA signal cable and installed Serial ATA
hard disk drives; otherwise, you cannot enter the RAID utility and SATA
BIOS setup during POST.
5 . Hard disk activity LED connector (4-pin HDLED1)
For some storage cards, such as SCSI card, with access signals for
external LEDs, this connector allows the access signals to go through
the front panel IDE_LED lead.
HDLED1
1
NCCH-DR
NCCH-DR
SCSI/SATA card activity LED connector
ASUS NCCH-DR
2-29
6 . CPU and system fan connectors (4-pin CPU_FAN1/2,
3-pin REAR_FAN1/2, FRNT_FAN1/2)
The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W
max.) or a total of 2.1 A ~ 4.44 A (53.28 W max.) at +12V. Connect
the fan cables to the fan connectors on the motherboard, making sure
that the black wire of each cable matches the ground pin of the
connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
CPU_FAN1
CPU_FAN2
GND
FANPWR2
Rotation
FANOUT4
REAR_FAN1
REAR_FAN2
FRNT_FAN2
FRNT_FAN1
NCCH-DR
GND
GND
NCCH-DR Fan connectors
+12V
+12V
Rotation
Rotation
7 . USB port connector (10-1 pin USB34)
This connector is for additional USB 2.0 ports. Connect the USB
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
Never connect a 1394 cable to the USB connectors. Doing so will
damage the motherboard!
USB34
NCCH-DR
NCCH-DR USB 2.0 connector
The USB port module is purchased separately.
Chapter 2: Hardware information
2-30
8 . SSI power connectors (24-pin ATXPWR1, 8-pin ATX12V1)
These connectors are for SSI power supply plugs. The power supply
plugs are designed to fit these connectors in only one orientation.
Find the proper orientation and push down firmly until the connectors
completely fit.
•
Use of an SSI 12 V Specification 2.0-compliant power supply unit
(PSU) that provides a minimum power of 450 W is recommended
for a fully-configured system.
•
•
Do not forget to connect the 8-pin ATX +12 V power plug;
otherwise, the system will not boot up.
Use of a PSU with a higher power output is recommended when
configuring a system with more power consuming devices. The
system may become unstable or may not boot up if the power is
inadequate.
•
You must install a PSU with a higher power rating if you intend to
install additional devices.
24-pin Power Connector
8-pin
1
NCCH-DR
For Power Supply
with 20-pin
Power Connector
NCCH-DR Power connectors
ASUS NCCH-DR
2-31
9 . Serial port connector (10-1 pin COM2)
This connector is for a serial (COM) port. Connect the serial port
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
COM2
PIN 1
NCCH-DR
NCCH-DR
Serial port2 (COM2) connector
The serial port module is purchased separately.
10. Printer port connector (26-1 pin LPT1)
This connector is for a parallel printer port. Connect the parallel printer
port module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
LPT1
Pin 1
NCCH-DR
NCCH-DR Parallel port connector
2-32
Chapter 2: Hardware information
11. Backplane SMBus connector (6-1 pin BPSMB1)
This connector allows you to connect SMBus (System Management
Bus) devices. Devices communicate with an SMBus host and/or other
SMBus devices using the SMBus interface.
BPSMB1
1
NCCH-DR
NCCH-DR SMBus connector
12. Power supply SMBus connector (5-pin PSUSMB1)
This connects SMBus (System Management Bus) devices to the power
supply unit. Devices communicate with an SMBus host and/or other
SMBus devices using the SMBus interface.
PSUSMB1
NCCH-DR
NCCH-DR Power supply SMBus connector
ASUS NCCH-DR
2-33
13. BMC connector (16-pin BMCCONN1)
This connector is for the optional ASUS server management card.
1
BMCCONN1
2
NCCH-DR
NCCH-DR BMC connector
14. Auxilliary panel connector (20-2 pin AUX_PANEL1)
This connector supports several front panel chassis-mounted
functions including chassis intrusion, LAN1/LAN2 link and activity
LEDs, Locator LED1/2, Locator switch, and front panel System
Management bus (SMBus).
LAN_LED1
LAN_LED2
SMBus
AUX_PANEL1
1
Chassis Intrusion
Locator LED2
NCCH-DR
Locator LED1 Locator switch
NCCH-DR Auxiliary panel connector
2-34
Chapter 2: Hardware information
15. System panel connector (20-pin PANEL1)
This connector supports several chassis-mounted functions.
Message LED SPEAKER
Power LED
PANEL1
HDD LED
NCCH-DR
NMI Button
RESET
PWRSW
NCCH-DR System panel connector
The sytem panel connector is color-coded for easy connection. Refer to
the connector descriptions on the next page for details.
•
•
System power LED (Green 3-pin PLED)
This 3-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
Message LED (Brown 2-pin MLED)
This connector is for the message LED cable that connects to the
front panel message LED. The message LED indicates the booting
status. The LED blinks when the system is in the boot process until
the operating system is loaded.
•
•
System warning speaker (Orange 4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
Hard disk drive activity LED (Red 2-pin HDD LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
•
•
ATX power button/soft-off button (Yellow 2-pin PWRSW)
This connector is for the system power button. Pressing the power
button turns the system on or puts the system in sleep or soft-off
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
Reset button (Blue 2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for
system reboot without turning off the system power.
ASUS NCCH-DR
2-35
2-36
Chapter 2: Hardware information
This chapter describes the power up
sequence, the vocal POST messages,
and ways of shutting down the
system.
Powering up
3
Chapter summary
3
3.1
3.2
Starting up for the first time................................................ 3-1
Powering off the computer .................................................. 3-2
ASUS NCCH-DR
3.1 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the
system chassis.
4. Connect the power cord to a power outlet that is equipped with a
surge protector.
5. Turn on the devices in the following order:
a. Monitor
b.External SCSI devices (starting with the last device on the chain)
c. System power
6. After applying power, the system power LED on the system front
panel case lights up. For systems withATX power supplies, the system
LED lights up when you press the ATX power button. If your monitor
complies with “green” standards or if it has a “power standby”
feature, the monitor LED may light up or switch between orange and
green after the system LED turns on.
The system then runs the power-on self tests or POST. While the
tests are running, the BIOS beeps (see BIOS beep codes table below)
or additional messages appear on the screen. If you do not see
anything within 30 seconds from the time you turned on the power,
the system may have failed a power-on test. Check the jumper
settings and connections or call your retailer for assistance.
Award BIOS beep codes
Beep Description
Error
One short beep when displaying logo
Long beeps in an endless loop
No error during POST
No DRAM installed or detected
High frequency beeps when
system is working
CPU overheated; System running at a lower
frequency
7. At power on, hold down the <Delete> key to enter the BIOS Setup.
Follow the instructions in Chapter 4.
ASUS NCCH-DR
3-1
3.2 Powering off the computer
3.2.1 Using the OS shut down function
If you are using Windows® 2000:
1. Click the Start button then click Shut Down...
2. Make sure that the Shut Down option button is selected, then click
the OK button to shut down the computer.
3. The power supply should turn off after Windows® shuts down.
If you are using Windows® XP:
1. Click the Start button then select Turn Off Computer.
2. Click the Turn Off button to shut down the computer.
3. The power supply should turn off after Windows® shuts down.
3.2.2 Using the dual function power switch
While the system is ON, pressing the power switch for less than four
seconds puts the system to sleep mode or to soft-off mode, depending on
the BIOS setting. Pressing the power switch for more than four seconds
lets the system enter the soft-off mode regardless of the BIOS setting.
Refer to section “4.5 Power Menu” in Chapter 4 for details.
3-2
Chapter 3: Powering up
This chapter tells how to change
the system settings through the BIOS
Setup menus. Detailed descriptions
of the BIOS parameters are also
provided.
BIOS setup
4
Chapter summary
4
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Managing and updating your BIOS ........................................ 4-1
BIOS Setup program ...........................................................4-13
Main menu ..........................................................................4-16
Advanced menu..................................................................4-20
Power menu........................................................................4-32
Boot menu ..........................................................................4-38
Exit menu ...........................................................................4-44
ASUS NCCH-DR
4.1 Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1. Award BIOS Flash Utility (Updates the BIOS in DOS mode using a
floppy disk.)
2. ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable
floppy disk or the motherboard support CD when the BIOS file fails or
gets corrupted.)
3. ASUS EZ Flash (Updates the BIOS in DOS mode using a floppy disk
or the motherboard support CD.)
4. ASUS Update (Updates the BIOS in Windows® environment.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy
disk in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or Award BIOS Flash utilities.
4.1.1 Creating a bootable floppy disk
1. Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click Start from the Windows® desktop, then select M y
Computer.
c. Select the 3 1/2 Floppy Drive icon.
d. Click File from the menu, then select Format. A Format 3 1/2
Floppy Disk window appears.
e. Windows® XP users: Select Create an MS-DOS startup
disk from the format options field, then click Start.
ASUS NCCH-DR
4-1
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click Start, then select Run.
d. In the Open field, type D:\bootdisk\makeboot a:
assuming that D is your optical drive letter.
e. Press <Enter>, then follow screen instructions to continue.
2. Copy the original or the latest motherboard BIOS file to the bootable
floppy disk.
4-2
Chapter 4: BIOS setup
4.1.2 AwardBIOS Flash Utility
The Basic Input/Output System (BIOS) can be updated using the
AwardBIOS Flash Utility. The following sections tell you how to update the
BIOS or how to save the current BIOS file.
Updating the current BIOS file
To update the current BIOS file:
1. Download the latest BIOS file from the ASUS web site. Extract the
zipped file, then save it to a floppy disk as *.BIN.
Save only the updated BIOS file in the floppy disk to avoid loading the
wrong BIOS file.
2. Copy the AwardBIOS Flash Utility (awdflash.exe) from the Software
folder of the support CD to the floppy disk with the latest BIOS file.
3. Boot the system in DOS mode using the bootable floppy disk you
created earlier.
4. When the A:> appears, replace the bootable floppy disk with the
floppy disk containing the new BIOS file and the Award BIOS Flash
Utility.
5. At the prompt, type awdflash then press <Enter>. The Award BIOS
Flash Utility screen appears.
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program :
Message: Please input File Name!
ASUS NCCH-DR
4-3
6. Type the BIOS file name in the File Name to Program field, then press
<Enter>.
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program : 1001.bin
Message: Do You Want To Save BIOS (Y/N)
7. The utility prompts you to save the current BIOS file. Press <Y> to
save the current BIOS file to the floppy disk, or <N> to continue.
If you intend to save the current BIOS file, make sure that the floppy
disk has enough disk space to save the file. See the next section for
details on saving the current BIOS file.
8. The utility verifies the BIOS file in the floppy disk and starts flashing
the BIOS file.
Do not turn off or reset the system during the flashing process!
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program : 1001.bin
Program Flashing Memory - 0FE00 OK
Write OK
No Update
Write Fail
Warning: Don’t Turn Off Power Or Reset System!
9. After the flashing process is completed, press <F1> to restart your
computer.
4-4
Chapter 4: BIOS setup
Copying the current BIOS file
You can use the AwardBIOS Flash Utility to save the current BIOS file. You
can load the current BIOS file when the BIOS file gets corrupted during the
flashing process.
To save the current BIOS file using the AwardBIOS Flash Utility:
1. Follow steps 1 to 6 of the previous section.
2. Press <Y> when the utility prompts you to save the current BIOS file.
The following screen appears.
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program : 1001.bin
Save current BIOS as :
Message:
3. Type a filename for the current BIOS file in the Save current BIOS as
field, then press <Enter>.
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program : 1001.bin
Checksum : 0E00
Save current BIOS as : old.bin
Message: Please Wait!
ASUS NCCH-DR
4-5
4. The utility saves the current BIOS file to the floppy disk, then returns
to the BIOS flashing process.
AwardBIOS Flash Utility for ASUS V1.05
(C) Phoenix Technologies Ltd. All Rights Reserved
For Canterwood - NCCH-DRC-00
DATE: 07/14/2004
Flash Type - SST 49LF008A /3.3V
File Name to Program : 1001.bin
Now Backup System BIOS to
File!
Message: Please Wait!Reset
4-6
Chapter 4: BIOS setup
4.1.3 ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to
restore the BIOS file when it fails or gets corrupted during the updating
process. You can update a corrupted BIOS file using the motherboard
support CD or the floppy disk that contains the updated BIOS file.
Prepare the motherboard support CD or the floppy disk containing the
updated motherboard BIOS before using this utility.
Recovering the BIOS from a floppy disk
To recover the BIOS from a floppy disk:
1. Turn on the system.
2. Insert the floppy disk with the AwardBIOS Flash Utility (awdflash.exe)
and the original or updated BIOS file to the floppy disk drive.
3. The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and automatically opens
the AwardBIOS Flash Utility.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4. Update the BIOS file following the instructions on the section “Award
BIOS Flash Utility”.
ASUS NCCH-DR
4-7
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1. Remove any floppy disk from the floppy disk drive, then turn on the
system.
2. Insert the support CD to the optical drive.
3. The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the
optical drive for the original or updated BIOS file. After finding the
updated BIOS file, the utility opens the AwardBIOS Flash Utility.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4. Update the BIOS file following the instructions on the section “Award
BIOS Flash Utility”.
The recovered BIOS may not be the latest BIOS version for this
motherboard. Visit the ASUS website (www.asus.com) to download the
latest BIOS file.
4-8
Chapter 4: BIOS setup
4.1.4 ASUS EZ Flash utility
The ASUS EZ Flash feature allows you to update the BIOS without having to
go through the long process of booting from a floppy disk and using a
DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is
accessible by pressing <Alt> + <F2> during the Power-On Self Tests
(POST).
To update the BIOS using EZ Flash:
1. Visit the ASUS website (www.asus.com) to download the latest BIOS
file for the motherboard.
2. Save the BIOS file to a floppy disk, then restart the system.
3. Press <Alt> + <F2> during POST to display the following.
EZFlash starting BIOS update
Checking for floppy...
4. Insert the floppy disk that contains the BIOS file to the floppy disk
drive. When the correct BIOS file is found, EZ Flash opens the
AwardBIOS Flash Utility.
EZFlash starting BIOS update
Checking for floppy...
Floppy found!
5. Update the BIOS file following the instructions on the section “Award
BIOS Flash Utility”.
•
•
Do not shutdown or reset the system while updating the BIOS to
prevent system boot failure!
A “Floppy not found!” error message appears if there is no floppy
disk in the drive. An error message also appears if the correct BIOS
file is not found in the floppy disk.s
ASUS NCCH-DR
4-9
4.1.5 ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update
the motherboard BIOS in Windows® environment. The ASUS Update utility
allows you to:
• Save the current BIOS file
• Download the latest BIOS file from the Internet
• Update the BIOS from an updated BIOS file
• Update the BIOS directly from the Internet, and
• View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1. Place the support CD in the optical drive. The Drivers menu appears.
2. Click the Utilities tab, then click Install ASUS Update
VX.XX.XX.
3. The ASUS Update utility is copied to your system.
Quit all Windows® applications before you update the BIOS using this
utility.
4-10
Chapter 4: BIOS setup
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1. Launch the ASUS Update utility from the Windows® desktop by clicking
Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The
ASUS Update main window appears.
2. Select Update BIOS from
the Internet option from the
drop-down menu, then click
Next.
3. Select the ASUS FTP site
nearest you to avoid network
traffic, or click Auto Select.
Click Next.
ASUS NCCH-DR
4-11
4. From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5. Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1. Launch the ASUS Update utility from the Windows® desktop by
clicking Start > Programs > ASUS > ASUSUpdate >
ASUSUpdate. The ASUS Update main window appears.
2. Select Update BIOS from a
file option from the drop-down
menu, then click Next.
3. Locate the BIOS file from the Open window, then click Save.
4. Follow the screen instructions to complete the update process.
4-12
Chapter 4: BIOS setup
4.2 BIOS Setup program
This motherboard includes a Flash ROM that you can update using the
provided utility described in section “4.1 Managing and updating your
BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup”. This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you may want to
change the configuration of your computer in the future. For example, you
may want to enable the security password feature or make changes to the
power management settings. This requires you to reconfigure your system
using the BIOS Setup program so that the computer can recognize these
changes and record them in the CMOS RAM of the Flash ROM.
The Flash ROM on the motherboard stores the Setup utility. When you start
up the computer, the system provides you with the opportunity to run this
program. Press <Delete> during the Power-On Self Test (POST) to enter
the Setup utility, otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You can also restart by turning the system off and then back on.
Do this last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. It is a
menu-driven program, which means you can scroll through the various
sub-menus and make your selections among the predetermined choices.
Because the BIOS software is constantly being updated, the following
BIOS setup screens and descriptions are for reference purposes only, and
may not exactly match what you see on your screen.
ASUS NCCH-DR
4-13
4.2.1 BIOS menu screen
Menu bar Menu items
General help
System Time
System Date
11: 10 : 30
Wed, Jul 21 2004
Select Menu
Item Specific Help
Legacy Diskette A
Floppy 3 Mode Support
[1.44M, 3.5 in.]
[Disabled]
Change the internal
clock.
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
[None]
[None]
[None]
[None]
[None]
[None]
Fourth IDE Master
Base Memory
Extended Memory
Total Memory
640K
260096K
261120K
Navigation keys
Field settings
4.2.2 Menu bar
The menu bar on top of the screen has the following main items:
Main For changing the basic system configuration settings
Advanced For changing the advanced system settings
Power
Boot
Exit
For changing the power configuration settings
For changing the system boot configuration settings
For selecting the exit options and loading default settings
To select the menu bar items, press the right or left arrow key on the
keyboard until the desired item is highlighted.
4.2.3 Navigation keys
At the bottom of a menu screen are the navigation keys for that
particular menu. Use the navigation keys to select items in the menu and
change the settings.
The navigation keys differ from one screen to another.
4-14
Chapter 4: BIOS setup
4.2.4 General help
On the right side of the menu screen is a brief description of the selected
item.
4.2.5 Sub-menu
An item with a sub-menu on any menu screen is distinguished by a solid
triangle before the item. To display the sub-menu, select the item and
press <Enter>.
4.2.6 Scroll bar
A scroll bar appears on the right side of a menu screen when there are
items that do not fit on the screen. Press Up/Down arrow keys or
PageUp/PageDown keys to display the other items on the screen.
4.2.7 Pop-up window
Select an item in the menu, then press <Enter> to display a pop-up window
with the configuration options for that item.
ASUS NCCH-DR
4-15
4.3 Main menu
When you enter the BIOS Setup program, the Main menu screen appears
giving you an overview of the basic system information.
Refer to section “4.2.1 BIOS menu screen” for information on the menu
screen items and how to navigate through them.
System Time
System Date
11: 10 : 30
Wed, Jul 21 2004
Select Menu
Item Specific Help
Legacy Diskette A
Floppy 3 Mode Support
[1.44M, 3.5 in.]
[Disabled]
Change the internal
clock.
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
Third IDE Master
[None]
[None]
[None]
[None]
[None]
[None]
Fourth IDE Master
Base Memory
Extended Memory
Total Memory
640K
260096K
261120K
System Time (hh:mm:ss)
Sets the system to the time that you specify (usually the current time).
The format is hour:minute:second. Valid values for hour, minute, and
second are Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59). Use
the <Tab> key to move between the hour, minute, and second fields.
System Date (mm:dd:yy)
Sets the system to the date that you specify (usually the current date).
The format is month:day:year. Valid values for month, day, and year are
Month: (1 to 12), Day: (1 to 31), Year: (1999 to 2099). Use the <Tab>
key to move between the month, day, and year fields.
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
Floppy 3 Mode Support [Disabled]
Enables support for older Japanese floppy drives. The Floppy 3 Mode
feature allows reading and writing of 1.28 MB (as opposed to 1.44 MB) on
a 3.5-inch floppy disk. Configuration options: [Disabled] [Drive A]
Base/Extended/Total Memory [xxxK]
The base memory, extended memory, and total memory values are
auto-detected. These fields are not user-configurable.
4-16
Chapter 4: BIOS setup
4.3.1 Primary IDE Master
Primary Master
Select Menu
Primary IDE Master
Access Mode
[Auto]
[Auto]
Item Specific Help
Selects the type of
fixed disk connected to
the system. ‘Manual’
will let you select the
number of cylinders,
heads, etc.
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
0
0
0
0
0
Note: PRECOMP=65535
means none!
PIO Mode
[Auto]
[Auto]
None
None
UDMA Mode
Transfer Mode
S.M.A.R.T Status
Primary IDE Master [Auto]
Select [Auto] to automatically detect an IDE drive. If automatic detection
is successful, the setup BIOS automatically fills in the correct values for the
remaining fields on this sub-menu.
If automatic detection fails, this may be because the IDE drive is too old or
too new. If the drive was already formatted on a previous system, the BIOS
may detect incorrect parameters. In these cases, select [Manual] to
manually enter the IDE drive parameters. Refer to the section “Manually
detecting an IDE drive.”
If no drive is installed or if you are removing a drive and not replacing it,
select [None]. Configuration options: [None] [Auto] [Manual]
The IDE drive information items are grayed out when this item is set to
[Auto].
Access Mode [Auto]
Allows selection of the sector addressing mode. The default [Auto] allows
automatic detection of an IDE drive. Set this item to [CHS] if the Primary
IDE Master item is set to [Manual] so you can manually enter the drive
values. Configuration options: [CHS] [LBA] [Large] [Auto]
PIO Mode [Auto]
Sets the PIO mode for the IDE drive. The settings Mode 0 to 4 allow
successive increase in performance. Configuration options: [Auto]
[Mode 0] [Mode 1] [Mode 2] [Mode 3] [Mode 4]
ASUS NCCH-DR
4-17
UDMA Mode [Auto]
When this item is set to [Auto], the UDMA capability allows improved
transfer speeds and data integrity for supported IDE drives. Configuration
options: [Disabled] [Auto]
Manually detecting an IDE drive
If you wish to manually enter the drive information, set the Primary IDE
Master item to [Manual], and the Access Mode item to [CHS].
Primary Master
[Manual]
Select Menu
Primary IDE Master
Access Mode
Item Specific Help
[CHS]
Selects the type of
fixed disk connected to
the system. ‘Manual’
will let you select the
number of cylinders,
heads, etc.
Capacity
0 MB
Cylinder
Head
Precomp
Landing Zone
Sector
[
[
[
[
[
0]
0]
0]
0]
0]
Note: PRECOMP=65535
means none!
PIO Mode
[Auto]
[Auto]
None
UDMA Mode
Transfer Mode
S.M.A.R.T Status
None
Before attempting to manually configure an IDE drive, make sure that
you have the correct configuration information supplied by the drive
manufacturer. Incorrect settings may cause the system to fail to
recognize the installed IDE drive!
To manually enter the number of cylinder, head, precomp, landing zone,
and sector per track for the drive, highlight an item, key-in the value that
you obtained from the drive documentation, then press <Enter>. Refer to
the drive documentation or the drive label for this information.
To enter a value, you may also highlight the item, then press <Enter> to
display a pop-up menu. Type in the value from the drive documentation,
then press <Enter>.
Capacity [xxxxx MB]
Displays the auto-detected hard disk capacity. The value is not
user-configurable.
Cylinder
Shows the number of the hard disk cylinders.
4-18
Chapter 4: BIOS setup
Head
Shows the number of the hard disk read/write heads.
Precomp
Displays the precompressed volumes on the hard disk, if any, on the
motherboard.
Landing Zone
Displays the drive’s maximum usable capacity as calculated by the BIOS
based on the drive information you entered.
Sector
Shows the number of sectors per track.
Transfer Mode
Shows the data transfer mode if the IDE hard disk drive supports the
feature. Otherwise, this item is grayed out and shows the value [None].
S.M.A.R.T. Status
Shows the Smart Monitoring, Analysis, and Reporting Technology
(S.M.A.R.T.) status if the IDE hard disk drive supports the feature.
Otherwise, this item is grayed out and shows the value [None].
After entering the IDE hard disk drive information, use a disk utility, such
as FDISK, to partition and format new IDE drives. This is necessary so
that you can write or read data from the hard disk. Make sure to set the
partition of the Primary IDE hard disk drive to “Active.”
4.3.2 Primary IDE Slave
When configuring a drive as Primary IDE Slave, refer to section “4.3.1
Primary IDE Master” for the menu item descriptions.
4.3.3 Secondary IDE Master
When configuring a drive as Secondary IDE Master, refer to section “4.3.1
Primary IDE Master” for the menu item descriptions.
4.3.4 Secondary IDE Slave
When configuring a drive as Secondary IDE Slave, refer to section “4.3.1
Primary IDE Master” for the menu item descriptions.
ASUS NCCH-DR
4-19
4.4 Advanced menu
The Advanced menu items allow you to change the settings for the CPU,
memory, chipset, and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values may cause the system to malfunction!
Select Menu
Advanced BIOS Features
CPU Configuration
Memory Configuration
Chipset
Item Specific Help
Onboard Device
PCIPnP
Virus Protection, Boot
Sequence...
USB Configuration
4-20
Chapter 4: BIOS setup
4.4.1 Advanced BIOS Features
This menu shows the console redirection and agent information. Select an
item then press <Enter> to display a pop-up menu with the configuration
options.
Advanced BIOS Features
Console Redirection [Disabled]
Select Menu
Item Specific Help
Baud Rate
Agent Address
Agent after boot
19200
[Auto]
[Disabled]
Enabled - Attempt to
redirect console via COM
port.
Disabled - Attempt to
redirect console when
keyboard is absent.
Console Redirection [Disabled]
Allows you to redirect the console through the serial port. when set to
[Enabled], the Baud Rate option is activated.
Configuration options: [Disabled] [Enabled]
Baud Rate [19200]
Allows you to set the console redirection Baud rate. This item is
user-configurable only when the Console Redirection option is set to
[Enabled]. Configuration options: [9600] [19200] [38400] [57600]
[115200]
Agent Address [Auto]
This option allows you to select the agent address.
Configuration options: [3F8h] [2F8h] [3E8h] [2E8h] [Auto]
Agent after boot [Disabled]
This option allows you to enable or disable the agent after boot-up.
Configuration options: [Disabled] [Enabled]
ASUS NCCH-DR
4-21
4.4.2 CPU Configuration
This menu shows the CPU configuration settings. Select an item then press
<Enter> to display a pop-up menu with the configuration options.
CPU Configuration
CPU L1 & L2 Cache [Enabled]
Select Menu
Item Specific Help
Hyper-Threading Technology [Enabled]
Disable/Enable CPU L1
L2 cache.
CPU L1 & L2 Cache [Enabled]
Allows you to enable or disable the CPU L1 and L2 cache.
Configuration options: [Disabled] [Enabled]
Hyper-Threading Technology [Enabled]
Allows you to enable or disable the Hyper-Threading Technology.
Configuration options: [Disabled] [Enabled]
4-22
Chapter 4: BIOS setup
4.4.3 Memory Configuration
This menu shows the memory configuration settings. Select an item then
press <Enter> to display a pop-up menu with the configuration options.
Memory Configuration
[Auto]
Select Menu
DRAM Frequency
Item Specific Help
Set DRAM Frequency.
Memory Timing Selectable
Cache Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
[By SPD]
3
8
4
4
Memory Parity Check
Disabled
DRAM Frequency [Auto]
This item sets the DRAM operating frequency.
Configuration options: [DDR266] [DDR320] [DDR400] [Auto]
Memory Timing Selectable [By SPD]
The DRAM clock are set according to the DRAM SPD (Serial Presence
Detect). Select [By SPD] for automatic DRAM clock detection. Select
[Manual] to allow setting the succeeding memory items to optimal timings.
Configuration options: [Manual] [By SPD]
The items CAS Latency Time, Active to Precharge Delay, DRAM RAS# to
CAS# Delay, and DRAM RAS# Precharge are configurable only when the
Memory Timing Selectable item is set to [Manual].
CAS Latency Time [2.5]
This item sets the latency (in clocks) between the DRAM read command
and the time the data actually becomes available.
Configuration options: [2] [2.5] [3]
Active to Precharge Delay [7]
This item controls the number of DRAM clocks used for DRAM parameters.
Configuration options: [8] [7] [6] [5]
DRAM RAS# to CAS# Delay [3]
Controls the latency between the DRAM active command and the read/
write command. Configuration options: [4] [3] [2]
ASUS NCCH-DR
4-23
DRAM RAS# Precharge [3]
This item controls the idle clocks after issuing a precharge command to the
DDR SDRAM. Configuration options: [4] [3] [2]
Memory Parity Check [Enabled]
Allows memory parity checking option. This item is not user-configurable
and set to [Enabled] by default.
4.4.4 Chipset
This menu shows the chipset configuration settings. Select an item then
press <Enter> to display a sub-menu with additional items, or show a pop-
up menu with the configuration options.
Chipset
Select Menu
System BIOS Cacheable
Video BIOS Cacheable
Init Display First
Auto Detect PCI Clk
[Enabled]
Item Specific Help
[Disabled]
[PCI VGA Card]
[Enabled]
Press <Enter> to enable
or disable BIOS
cacheable.
System BIOS Cacheable [Enabled]
Allows you to enable or disable the cache function of the system BIOS.
Configuration options: [Disabled] [Enabled]
Video BIOS Cacheable [Disabled]
Allows you to enable or disable the cache function of the video BIOS.
Setting to [Enabled] improves the display speed by caching the display
data. Configuration options: [Disabled] [Enabled]
Init Display First [PCI VGA Card]
Allows you to select the graphics controller to use as primary boot device.
Configuration options: [PCI VGA Card] [Onboard VGA]
Auto Detect PCI Clk [Enabled]
Allows you to select the maximum PCI bus speed to be programmed.
Configuration options: [Enabled] [Disabled]
4-24
Chapter 4: BIOS setup
4.4.5 Onboard Device
This menu shows the onboard device configuration settings. Select an item
then press <Enter> to display a sub-menu with additional items, or show a
pop-up menu with the configuration options.
Onboard Device
Select Menu
H/W Jumper of CSA LAN
Enabled
[Disabled]
Enabled
Item Specific Help
Onboard CSA LAN Boot ROM
H/W Jumper of ONB LAN
Onboard LAN Boot ROM
Super I/O Device
Enable/Disable Onboard
CSA LAN device boot ROM
support.
[Disabled]
SATA Configuration
H/W Jumper of CSA LAN [Enabled]
This option tells whether the CSA LAN jumper labeled LAN_EN1 on the
motherboard is enabled or disabled. See section “2.6 Jumpers” for details.
Onboard CSA LAN Boot ROM [Disabled]
Allows you to enable or disable the onboard CSA LAN boot ROM.
Configuration options: [Disabled] [Enabled]
H/W Jumper of ONB LAN [Enabled]
This option tells whether the onboard LAN jumper labeled LAN_EN2 on the
motherboard is enabled or disabled. See section “2.6 Jumpers” for details.
Onboard LAN Boot ROM [Disabled]
Allows you to enable or disable the onboard LAN boot ROM.
Configuration options: [Disabled] [Enabled]
ASUS NCCH-DR
4-25
Super I/O Device
Select Menu
Super I/O Device
Serial Port1 Address
Serial Port2 Address
Onboard Parallel Port
Parallel Port Mode
EPP Mode Select
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
[SPP]
EPP1.7
3
Item Specific Help
Set Base I/O address
for serial port 1.
ECP Mode Use DMA
Serial Port 1 [3F8/IRQ4]
Serial Port 2 [2F8/IRQ3]
Allow you to select the serial port base addresses.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4]
[2E8/IRQ3] [Auto]
Onboard Parallel Port [378/IRQ7]
Allows you to select the parellel port base address.
Configuration options: [Disabled] [378/IRQ7] [278/IRQ5] [3BC/IRQ7]
Parallel Port Mode [SPP]
Allows you to select the parallel port mode.
Configuration options: [SPP] [EPP] [ECP] [ECP+EPP] [Normal]
EPP Mode Select [EPP1.7]
Allows you to select the EPP mode. This item becomes configurable only if
the Parallel Port Mode is set to [EPP] or [ECP+EPP].|
Configuration options: [EPP 1.9] [EPP 1.7]
ECP Mode Use DMA [3]
Allows you to select the ECP mode. This item becomes configurable only if
the Parallel Port Mode is set to [ECP] or [ECP+EPP].
Configuration options: [1] [3]
4-26
Chapter 4: BIOS setup
SATA Configuration
Select Menu
SATA Configuration
*** On-Chip Serial ATA Setting ***
Item Specific Help
On-Chip Serial ATA
SATA Mode
[Auto]
IDE
SATA0 master
SATA1 master
[Disabled]: Disable
SATA Controller.
[Auto]: Auto-arrange
the BIOS.
Serial ATA Port0 Mode
Serial ATA Port1 Mode
[Combined Mode]: PATA
and SATA are combined.
Max. of 2 IDE drives on
each channel.
[Enhanced Mode]: Enable
both SATA and PATA.
Max. of 6 IDE drives
are supported.
[SATA Only]: SATA is
opeating in legacy
mode.
***On-Chip Serial ATA Setting***
The SATA Mode and Serial ATA Port0 Mode items are configurable
only when the On-Chip Serial ATA item is set to [ Combined Mode]
[Enhanced Mode] or [SATA Only].
On-chip Serial ATA [Auto]
This item allows you to configure your serial ATA devices, if present.
Configuration options: [Disabled] [Auto] [Combined Mode]
[Enhanced Mode] [SATA Only]
a.
b.
Setting to [Auto] allows BIOS to automatically configure the SATA
devices.
Setting to [Combined Mode] allows you to install parallel ATA and
serial ATA devices at the same time. You may install two IDE
devices on any of the parallel ATA channels, and one IDE
device on each serial ATA channel for a maximum of four
devices. Use ths option when you installed a legacy operating system
like MS-DOS, Windows ME/98/NT4.0.
c.
Setting to [Enhanced Mode] allows you to install parallel ATA and
serial ATA devices at the same time, with a maximum of six IDE
devices on each channel. Use this option when you installed a native
operating system like Windows 2000/XP.
d.
e.
Setting to [SATA Only] allows you to install IDE devices on the
Serial ATA channels only.
Setting to [Disabled] disables the onboard SATA controller. The
RAID feature is also disabled.
ASUS NCCH-DR
4-27
SATA Mode [IDE]
When set to [RAID], this item allows configuration of the installed IDE
devices into a disk array. Configuration options: [IDE] [RAID]
Serial ATA Port0 Mode [SATA0 master]
Serial ATA Port1 Mode [SATA1 master]
Allow you to set the SATA Port0 and Serial ATA Port1 modes. The options
for these items vary depending on the setting of the On-Chip Serial
ATA item. Configuration options: [Primary Master] [Primary Slave]
[Secondary Master] [Secondary Slave] [SATA0 master] SATA1 master]
4-28
Chapter 4: BIOS setup
4.4.6 PCIPnP
This menu shows the PCIPnP configuration settings. Select an item then
press <Enter> to display a pop-up menu with the configuration options.
PCIPnP
Reset Configuration Data
Select Menu
[Disabled]
[Auto]
Item Specific Help
Resources Controlled By
IRQ Resources
Default is Disabled.
Select Enabled to reset
Extended System
PCI/VGA Pallete Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
[Disabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
Configuration Data
(ESCD) when you exit
Setup, if you installed
a new add-on card and
the system
reconfiguration has
caused a serious
conflict that the OS
cannot boot.
Reset Configuration Data [Disabled]
Allows you to enable or disabled resetting of the Extended System
Configuration Data (ESCD) when you exit the Setup. The ESCD includes
information on non-PnP devices. Set this item to [Enabled] if you installed
an expansion card that conflicts with other devices and cause system boot
failure. Configuration options: [Disabled] [Enabled]
Resources Controlled By [Auto]
When set to [Auto(ESCD)], allows BIOS to automatically configure of all
boot and Plug and Play devices. When set to [Manual], you can assign the
available IRQ Resources to the PCI devices.
Configuration options: [Auto] [Manual]
When the item Resources Controlled By is set to [Auto], the item
IRQ Resources is grayed out and not user-configurable. Refer to the
section “IRQ Resources” for information on how to enable this item.
PCI/VGA Pallete Snoop [Disabled]
Some non-standard VGA cards, like graphics accelerators or MPEG video
cards, may not show colors properly. Setting this field to [Enabled] corrects
this problem. If you are using a standard VGA card, leave this field to the
default setting [Disabled]. Configuration options: [Disabled] [Enabled]
INT Pin 1~8 Assignment [Auto]
Allows you to select the appropriate interrupt to the specific devices to
avoid conflict. Configuration options: [Auto] [3] [4] [5] [7] [9] [10] [11]
[12] [14] [15]
ASUS NCCH-DR
4-29
IRQ Resources
Set the item Resources Controlled By is set to [Manual] to enable
the item IRQ Resources and assign the interrupts depending on the
type of installed PCI device.
PCIPnP
Reset Configuration Data
Select Menu
Item Specific Help
[Disabled]
[Manual]
BIOS can automatically
configure all the boot
and Plug and Play
Resources Controlled By
IRQ Resources
compatible devices. If
you choose auto, you
cannot select IRQ DMA
and memory base address
fields, since BIOS
PCI/VGA Pallete Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
[Disabled]
[Auto]
[Auto]
[Auto]
[Auto]
Select Menu
IRQ Resources
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
Item Specific Help
Legacy ISA for devices
compliant with the
original PC AT bus
specification, PCI/ISA
PnP for devices
compliant with the Plug
and Play standard
whether designed for PCI
or ISA bus architecture.
IRQ-xx assigned to [PCI device]
The IRQ Resources sub-menu is activated when the Resources Controlled by
parameter is set to [Manual]. Select [PCI Device] to assign an IRQ address
to a Plug and Play device. Setting to [Reserved] reserves the IRQ address.
Configuration options: [PCI Device] [Reserved]
4-30
Chapter 4: BIOS setup
4.4.7 USB Configuration
This menu shows the USB configuration settings. Select an item then press
<Enter> to display a pop-up menu with the configuration options.
Select Menu
USB Configuration
[Enabled]
USB Controller
USB 2.0 Support
Item Specific Help
[Enabled]
[Enabled]
USB Legacy Mode Support
Configures the USB
controller.
USB Controller [Enabled]
Allows you enable or disable the USB controller.
Configuration options: [Enabled] [Disabled]
USB 2.0 Support [Enabled]
Allows you to enable or disable the EHCI controller. Setting this item to
[Enabled] allows the built-in high speed USB support in the BIOS to turn on
automatically when you install high speed USB devices.
Configuration options: [Enabled] [Disabled]
USB Legacy Mode Support [Enabled]
Allows you enable or disable support for the legacy USB devices.
Configuration options: [Disabled] [Enabled]
ASUS NCCH-DR
4-31
4.5 Power menu
The Power menu items allow you to change the settings for the Advanced
Power Management (APM). Select an item then press <Enter> to display
the configuration options.
ACPI APIC Support
APM Configuration
Hardware Configuration
[Enabled]
Select Menu
Item Specific Help
Enable/Disable ACPI
support for Operating
System.
ACPI APIC Support [Enabled]
Allows you to enable or disable the ACPI feature on the operating system.
Configuration options: [Disabled] [Enabled]
4-32
Chapter 4: BIOS setup
4.5.1 APM Configuration
This menu shows the Advanced Power Management (APM) configuration
settings. Select an item then press <Enter> to display a pop-up menu with
the configuration options.
Select Menu
APM Configuration
[User Define]
Power Management
HDD Power Down
Suspend Mode
Item Specific Help
[Disabled]
[Disabled]
[Stop Grant]
[Power Off]
[DPMS]
This field allows you
to set the automatic
power saving features.
Suspend Type
Restore on AC Power Loss
Video Off Method
Video Off In Suspend
MODEM Use IRQ
[Yes]
[3]
Soft-Off by PWR-BTN
Power On By PCI Devices
[Instant-Off]
[Enabled]
Power On By External Modem [Disabled]
POWER ON Function
KB Power On Password
Hot Key Power ON
Resume By Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
[Button Only]
Enter
Ctrl-F1
[Disabled]
0
0 : 0 : 0
Power Management [User Define]
Allows you to set the automatic power saving features.
Configuration options: [User Define] [Min. Saving] [Max. Saving]
HDD Power Down [Disabled]
Shuts down any IDE hard disk drives in the system after a period of
inactivity as set in this user-configurable field. This feature does not affect
SCSI hard drives. Configuration options: [Disabled] [1 Min] ... [15 Min]
Suspend Mode [Disabled]
Sets the time period before the system goes into suspend mode.
Configuration options: [Disabled] [1 Min] [2 Min] [4 Min] [8 Min] [12 Min]
[20 Min] [30 Min] [40 Min] [1 Hr]
Suspend Type [Stop Grant]
Allows you to select the suspend type.
Configuration options: [Stop Grant] [PwrOn Suspend]
Restore on AC Power Loss [Power Off]
When set to [Power Off], the system goes into “off state” after an AC
power interruption. When set to [Power On], the system turns on
automatically after an power interruption. When set to [Last State], the
system goes into whatever was the system state (on or off) before the
power interruption. Configuration options: [Power Off] [Power On]
[Last State]
ASUS NCCH-DR
4-33
Video Off Method [DPMS]
This item determines the video off features. The Display Power
Management System (DPMS) feature allows the BIOS to control the video
display card if it supports the DPMS feature. [Blank Screen] only blanks the
screen. Use this for monitors without power management or “green”
features. Configuration options: [Blank Screen] [V/H SYNC+Blank] [DPMS]
Video Off In Suspend [Yes]
This item determines when to activate the video off feature for monitor
power management. Configuration options: [No] [Yes]
MODEM Use IRQ [3]
Allows you to select the IRQ assignment for the modem.
Configuration options: [NA] [3] [4] [5] [7] [9] [10] [11]
Soft-Off by PWR-BTN [Instant-Off]
When set to [Instant-Off], the system goes to soft off when you press the
power button for less than 4 seconds. When set to [Delay 4 Sec], press
the power button for more than 4 seconds to power off the system.
Configuration options: [Instant-Off] [Delay 4 Sec.]
Power On By PCI Devices [Enabled]
Allows you to enable or disable the PME to generate a wake-up event.
Configuration options: [Disabled] [Enabled]
Power On By External Modem [Disabled]
Allows you to enable or disable system power up when the external modem
receives a call while in soft-off mode.
Configuration options: [Disabled] [Enabled]
Power On Function [BUTTON ONLY]
Allows you to select a device to turn the system power on.
Configuration options: [Password] [Hot Key] [Any KEY] [BUTTON ONLY]
[PS/2 Mouse]
KB Power On Password [Enter]
Allows you to set a password to turn the system power on. Highlight this
item then press enter to set a password.
To configure this item, you should set the Power On Function item
to [Password].
4-34
Chapter 4: BIOS setup
Hot Key Power On [Ctrl-F1]
Allows you to set a hot key combination to turn the system power on.
Configuration options: [Ctrl-F1] ... [Ctrl-F12]
To configure this item, you should set the Power On Function item
to [Hot Key].
Resume by Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. When this
item is enabled, you can set the date and time of alarm using the two
following items. Configuration options: [Disabled] [Enabled]
Date (of Month) Alarm [0]
To set the date of alarm, highlight this item and press <Enter> to display a
pop-up menu. Key-in a value within the specified range then press <Enter>.
Configuration options: [Min=0] [Max=31]
Time (hh:mm:ss) Alarm [0 : 0 : 0]
To set the time of alarm:
1. Highlight this item and press <Enter> to display a pop-up menu for the
hour field.
2. Key-in a value (Min=0, Max=23), then press <Enter>.
3. Press tab to move to the minutes field, then press <Enter>.
4. Key-in a minute value (Min=0, Max=59), then press <Enter>.
5. Press tab to move to the seconds field, then press <Enter>.
6. Key-in a value (Min=0, Max=59), then press <Enter>.
ASUS NCCH-DR
4-35
4.5.2 Hardware Monitor
This menu shows the hardware monitoring status. Select a sub-menu then
press <Enter> to display the configuration options.
Select Menu
Hardware Monitor
Voltage Monitor
Item Specific Help
Smart Q-Fan Configuration
System Temperature
CPU1 Temperature
42oC/107oF
56oC/132oF
45oC/113oF
29oC/ 84oF
36oC/ 96oF
0 RPM
Press Enter to view.
CPU2 Temperature
M/B Front Temperature
M/B Rear Temperature
Front Fan1 Speed
CPU
CPU
Fan1 Speed
Fan2 Speed
5152 RPM
5100 RPM
0 RPM
Front Fan2 Speed
Rear Fan1 Speed
Rear Fan2 Speed
0 RPM
0 RPM
Voltage Monitor
Voltage Monitor
Select Menu
CPU VCORE A (V)
+3.3V Voltage
+12V Voltage
+1.5V Voltage
+2.5V Voltage
+5VCC Voltage
+5VSB Voltage
VBAT Voltage
1.48V
3.26V
11.79V
1.49V
2.47V
4.99V
4.75V
3.10V
Item Specific Help
CPU VCORE A, +3.3V Voltage, +12V Voltage, +1.5V
Voltage, +2.5V Voltage, +5VCC Voltage,
+5VSB Voltage,VBAT Voltage,
These fields show the auto-detected voltages through the onboard voltage
regulators.
4-36
Chapter 4: BIOS setup
Smart Q-Fan Configuration
Smart Q-Fan Configuration
Select Menu
Smart Fan Control
[Disabled]
Item Specific Help
System Target Temperature
CPU1 Target Temperature
CPU2 Target Temperature
50
55
55
Press Enter to enable
or disable the Smart
Fan.
Smart Fan Control [Disabled]
Allows you to enable or disable the Smart Fan feature. This feature smartly
adjusts the CPU/system fan rotations based on the user-assigned
threshold temperature. Configuration options: [Disabled] [Enabled]
System Target Temperature [50]
CPU1 Target Temperature [55]
CPU2 Target Temperature [55]
Allows you to set the threshold temperature at which the Smart Fan
Control feature is disabled.
ASUS NCCH-DR
4-37
4.6 Boot menu
The Boot menu items allow you to change the system boot settings. Select
an item then press <Enter> to display a sub-menu with additional items, or
show a pop-up menu with the configuration options.
Boot Device Priority
Select Menu
Hard Disk Boot Priority
Removable Device Priority
CD-ROM Boot Priority
Item Specific Help
Select Boot Device
Priority.
Boot Settings Configuration
Security
4.6.1 Boot Device Priority
Boot Device Priority
Select Menu
1st Boot Device
2nd Boot Device
3rd Boot Device
[Removable]
[CDROM]
[Hard Disk]
Item Specific Help
Select your Boot Device
Priority.
1st Boot Device [Removable]
2nd Boot Device [CDROM]
3rd Boot Device [Hard Disk]
Allows you to select your boot device priority.
Configuration options: [Removable] [Hard Disk] [CDROM] [Legacy LAN]
[Disabled]
4-38
Chapter 4: BIOS setup
4.6.2 Hard Disk Boot Priority
Hard Disk Boot Priority
Select Menu
1. 1st Master: XXXXXXXX
2. Bootable Add-in Cards
Item Specific Help
Use <up> or <down>
arrow to select a
device, then press <+>
to move it up, or <->
to move it down the
list. Press <ESC> to
exit this menu.
4.6.3 Removable Device Priority
Removable Priority
1. Floppy Disks
Select Menu
Item Specific Help
Use <up> or <down>
arrow to select a
device, then press <+>
to move it up, or <->
to move it down the
list. Press <ESC> to
exit this menu.
ASUS NCCH-DR
4-39
4.6.4 CD-ROM Boot Priority
CD-ROM Boot Priority
Select Menu
1. 1st Slave : ASUS
CD-S520/A
Item Specific Help
Use <up> or <down>
arrow to select a
device, then press <+>
to move it up, or <->
to move it down the
list. Press <ESC> to
exit this menu.
4.6.5 Boot Settings Configuration
Boot Settings Configuration
Select Menu
Boot Other Device
Quick Power On Self Test
Halt On
[Enabled]
[Enabled]
[All Errors]
[Enabled]
[Enabled]
[On]
[Disabled]
6
250
Item Specific Help
Select your Boot Device
Priority.
Case Open Warning
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Full Screen LOGO Show
[Enabled]
Boot Other Device [Enabled]
Allows you to enable or disable selection of other boot device.
Configuration options: [Disabled] [Enabled]
Quick Power On Self Test [Enabled]
This field speeds up the Power-On-Self Test (POST) routine by skipping
retesting a second, third, and fourth time. Configuration options: [Disabled]
[Enabled]
4-40
Chapter 4: BIOS setup
Halt On [All Errors]
Sets the system to halt on errors according to the system functions
specified in each option. Configuration options: [All Errors] [No Errors] [All,
But Keyboard] [All , But Diskette] [All, But Disk/Key]
Case Open Warning [Enabled]
Allows you to enable or disable the case open status feature. Setting to
[Enabled] clear the case open status. Configuration options: [Disabled]
[Enabled]
Boot Up Floppy Seek [Enabled]
When enabled, the BIOS will seek the floppy disk drive to determine
whether the drive has 40 or 80 tracks. Configuration options: [Disabled]
[Enabled]
Boot Up NumLock Status [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Typematic Rate Setting [Disabled]
Allows you to enable or disable the keyboard typematic rate setting. Set to
[Enabled] to configure the Type Rate and Type Delay items. Configuration
options: [Disabled] [Enabled]
The items Typematic Rate (Chars/Sec) and Typematic Delay
become configurable only when the item Typematic Setting is enabled.
Typematic Rate (Chars/Sec) [6]
Allows you to select the rate at which character repeats when you hold a
key. Configuration options: [6] [8] [10] [12] [15] [20] [24] [30]
Typematic Delay (Msec) [250]
Allows you to set the delay before key strokes begin to repeat.
Configuration options: [250] [500] [750] [1000]
Full Screen LOGO Show [Enabled]
Setting to [Enabled] displays the logo instead of the POST messages.
Setting to [Disabled] displays the normal POST messages.
Configuration options: [Disabled] [Enabled]
ASUS NCCH-DR
4-41
4.6.6 Security
Security
Select Menu
Supervisor Password
User Password
Password Check
Clear
Clear
[Setup]
Item Specific Help
Supervisor password
control full access.
Supervisor Password [Clear]
User Password [Clear]
These fields allow you to set passwords.
To set a password:
1. Highlight an item then press <Enter>.
2. Type in a password using eight (8) alphanumeric characters, then
press <Enter>.
3. When prompted, confirm the password by typing the exact characters
again, then press <Enter>. The password field setting is changed to
[Set].
To clear the password:
1. Highlight the password field, and press <Enter> twice. The following
message appears:
“PASSWORD DISABLED!!! Press any key to continue...”
2. Press any key to return to the menu.
A note about passwords
The Supervisor password is required to enter the BIOS Setup program
preventing unauthorized access. The User password is required to
boot the system preventing unauthorized use.
4-42
Chapter 4: BIOS setup
Forgot the password?
If you forget your password, you can clear it by erasing the CMOS
Real Time Clock (RTC) RAM. The RAM data containing the password
information is powered by the onboard button cell battery. If you
need to erase the CMOS RAM, refer to section “2.6 Jumpers” for
instructions.
Password Check [Setup]
This field requires you to enter the password before entering the BIOS
setup or the system. Select [Setup] to require the password before
entering the BIOS Setup. Select [System] to require the password before
entering the system. Configuration options: [Setup] [System]
ASUS NCCH-DR
4-43
4.7 Exit menu
The Exit menu items allow you to load the BIOS setup default settings,
save or discard any changes you made, or exit the Setup utility.
Exit & Save Changes
Exit & Discard Changes
Load Setup Defaults
Discard Changes
Select Menu
Item Specific Help
This option saves data
to CMOS before exiting
Setup.
Exit & Save Changes
Select this option then press Enter, or simply press <F10>, to save your
changes to CMOS before exiting the Setup utility. When a confirmation
window appears, type [Y] to save and exit, or [N] to cancel and return to
the menu.
Exit & Discard Changes
Select this option then press Enter if you wish to exit the Setup utility
without saving your changes. When a confirmation window appears, type
[Y] to exit and discard your changes, or [N] to cancel and return to the
menu.
Load Setup Defaults
Select this option then press Enter, or simply press <F5>, to load the
optimized values for each of the Setup menu items. When a confirmation
window appears, type [Y] to load the default values, or [N] to cancel and
return to the menu.
Discard Changes
Select this option to discard the changes that you made, and restore the
previously saved values. When a confirmation appears, type [Y] to discard
any changes and load the previously saved values, or [N] to cancel and
return to the menu.
4-44
Chapter 4: BIOS setup
This chapter describes the power up
sequence, the vocal POST messages,
and ways of shutting down the
system.
Reference information
A
Appendix summary
A
A.1
NCCH-DR block diagram .......................................................A-1
ASUS NCCH-DR
A.1 NCCH-DR block diagram
TM
TM
Intel Xeon
Intel Xeon
with 800MHz system bus
with 800MHz system bus
System Bus
64bit, 800 MHz
IntelR E7210
MCH
Four
DDR400 DIMM
Sockets
4xDDR 400 DIMM slots (max. 4GB)
CSA
Intel R
82547GI
Gigabit LAN
controller
Intel R
82541GI
Gigabit LAN
controller
Hub interface 1.5
Intel R 6300ESB
ICH
PCI 33 bus
ATI Rage XL
8 MB
VGA-Conn.
PCI-X 66MHz bus
SATA RAID
Adaptec AIC-8130
H/W
EEPROM
monitor
SMBus
System
W83792D
information
IDE 1
IDE 2
Fan
Power Supply
LPC-Bus
BIOS Flash
8 Mbit
Super I/O
W83627THF-A
USB 1
USB 4
Keyboard
Floppy
Mouse
Serial Port1
ASUS NCCH-DR
A-1
A-2
Appendix A: Reference information
|
Hanns G JC199 User Manual
Electrolux Thermaline 9CHG584146 User Manual
Electrolux EW30GC55GW User Manual
Diamond Multimedia Radeon GX700PCIE256 CN User Manual
Diamond Multimedia ATI Radeon HD 4800 Series User Manual
Cuisinart TOB 60 Series User Manual
Bosch Appliances Convection Oven HBN54 User Manual
Asus LCD Monitor VW226TTAA User Manual
Asus LCD MONITOR VG278HE User Manual
Accton Technology EN2216 2 User Manual