Asus LCD Monitor PQ321Q User Manual

LCD Monitor  
User Manual  
PQ321 Series  
 
IMPORTANT INFORMATION  
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR  
MOISTURE.  
The lightning flash with arrowhead symbol, within  
a triangle, is intended to alert the user to the  
presence of uninsulated “dangerous voltagewithin  
CAUTION  
the product’s enclosure that may be of sufficient  
magnitude to constitute a risk of electric shock to  
persons.  
RISK OF ELECTRIC  
SHOCK  
DO NOT OPEN  
The exclamation point within a triangle is intended  
to alert the user to the presence of important  
operating and maintenance (servicing) instructions  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO  
NOT REMOVE COVER.  
in the literature accompanying the product.  
NO USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
NOTE:  
Federal Communications Commission Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
• This device may not cause harmful interference, and  
• This device must accept any interference received including interference that may cause undesired operation.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions,  
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC  
regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
Canadian Department of Communications Statement  
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio  
Interference Regulations of the Canadian Department of Communications.  
This class B digital apparatus complies with Canadian ICES-003.  
This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada.  
E
DEAR ASUS CUSTOMER  
Thank you for your purchase of the ASUS LCD product. To ensure safety and many years of trouble-free operation of your product,  
®
please read the Safety Precautions carefully before using this product.  
SAFETY PRECAUTIONS  
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled.  
This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric  
shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning  
the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully  
before using the product.  
1. Read instructions — All operating instructions must be read and understood before the product is operated.  
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future reference.  
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.  
4. Follow instructions — All operating instructions must be followed.  
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do not use  
liquid cleaners or aerosol cleaners.  
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in  
accidents.  
7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto it. Be  
careful of equipment which drains water such as an air-conditioner.  
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.  
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the  
product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings. Do not place the  
product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are  
followed.  
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from  
resting on them.  
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be  
careful not to be injured by broken glass pieces in case the LCD panel breaks.  
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.  
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in the  
product, and inserting an object can cause electric shock and/or short internal parts.  
For the same reason, do not spill water or liquid on the product.  
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous  
conditions. Request a qualified service person to perform servicing.  
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person  
to perform repairs.  
a. When the power cord or plug is damaged.  
b. When a liquid was spilled on the product or when objects have fallen into the product.  
c. When the product has been exposed to rain or water.  
d. When the product does not operate properly as described in the operating instructions.  
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not  
described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician.  
e. When the product has been dropped or damaged.  
f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product needs  
servicing.  
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement parts  
specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized  
parts can result in fire, electric shock and/or other danger.  
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to ensure that  
the product is in proper operating condition.  
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method recommended by  
the manufacturer.  
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products  
(including amplifiers).  
19. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury, severe  
physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch  
control in a weapon system.  
20. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in  
low-temperature burns.  
E
SAFETY PRECAUTIONS (Continued)  
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal and  
DisplayPort input terminal.  
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly  
to children, can be avoided by taking simple precautions such as:  
• Using fixing devices like wall mount brackets recommended by the manufacturer.  
• Only using furniture that can safely support the monitor.  
• Ensuring the monitor is not overhanging the edge of the supporting furniture.  
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the  
monitor to a suitable support.  
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.  
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.  
Especially for child safety  
- Don’t allow children to climb on or play with the monitor.  
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.  
- Remember that children can become excited while watching a program, especially on a “larger than lifemonitor. Care should be  
taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.  
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by curious  
children.  
E
TIPS AND SAFETY INSTRUCTIONS  
- The TFT color LCD panel used in this monitor is made with the  
application of high precision technology. However, there may  
be minute points on the screen where pixels never light or are  
permanently lit. Also, if the screen is viewed from an acute angle  
there may be uneven colors or brightness. Please note that these  
are not malfunctions but common phenomena of LCDs and will  
not affect the performance of the monitor.  
The Power Cord and AC adapter  
- Use only the power cord and AC adapter supplied with the  
monitor.  
- When handling the AC adapter, observe the following: Incorrect  
handling may result in fire, electric shock, or injury.  
• Do not drop the AC adapter or subject it to impact.  
• Never disassemble the AC adapter. It contains high voltage  
parts that are dangerous to touch.  
• The AC adapter is for indoor use only. Do not use it outside.  
• Do not use the supplied AC adapter with other devices.  
- Do not display a still picture for a long period, as this could cause  
a residual image.  
- Never rub or tap the monitor with hard objects.  
- Please understand that ASUSTek Computer Inc. bears no  
responsibility for errors made during use by the customer or a  
third party, nor for any other malfunctions or damage to this  
product arising during use, except where indemnity liability is  
recognized under law.  
- Do not damage the power cord and AC adapter nor place heavy  
objects on it, stretch it or over bend it. Also, do not add extension  
cords. Damage to the cord may result in fire or electric shock.  
- Do not use the power cord with a power tap.  
Adding an extension cord may lead to fire as a result of  
overheating.  
- This monitor and its accessories may be upgraded without  
advance notice.  
- Do not remove or insert the power plug with wet hands. Doing  
so could result in electric shock.  
- Do not use the monitor where there is a lot of dust, where  
humidity is high, or where the monitor may come into contact  
with oil or steam, as this could lead to fire.  
- Unplug the power cord if it is not used for a long time.  
-
Do not attempt to repair the power cord if it is broken or  
malfunctioning. Refer the servicing to the service representative.  
- Ensure that the monitor does not come into contact with water  
or other fluids. Ensure that no objects such as paper clips or pins  
enter the monitor as this could lead to fire or electric shock.  
- Do not stay in contact with the parts of the product and the AC  
adapter that become hot for long periods of time.  
Doing so may result in low-temperature burns.  
- Do not place the monitor on top of unstable objects or in unsafe  
places. Do not allow the monitor to receive strong shocks or to  
strongly vibrate. Causing the monitor to fall or topple over may  
damage it.  
-
Do not fasten the AC adapter to the monitor or other equipment.  
Doing so may result in fire and electrical shock.  
- Do not use the monitor near heating equipment or in places  
where there is likelihood of high temperature, as this may lead to  
generation of excessive heat and outbreak of fire.  
Manual Scope  
- Microsoft, Windows and Internet Explorer are registered  
trademarks of Microsoft Corporation.  
- Do not use the monitor in places where it may be exposed to  
direct sunlight.  
- The terms HDMI and HDMI High-Definition Multimedia Interface,  
and the HDMI Logo are trademarks or registered trademarks of  
HDMI Licensing LLC in the United States and other countries.  
- Images cannot be rotated on this monitor.  
When using in portrait orientation, you will need to prepare  
appropriately orientated content in advance.  
- DisplayPort is a registered trademark of Video Electronics  
Standards Association.  
- The AC outlet shall be installed near the equipment and shall be  
easily accessible.  
- Adobe, Acrobat, and Reader are either registered trademarks or  
trademarks of Adobe Systems Incorporated in the United States  
and/or other countries.  
- This product comes with RICOH Bitmap Fonts produced and sold  
by RICOH COMPANY, LTD.  
- All other brand and product names are trademarks or registered  
trademarks of their respective holders.  
- Language of OSD menu used in this manual is English by way of  
example.  
- Illustrations in this manual may not exactly represent the actual  
product or display.  
- This manual assumes use in landscape orientation, except where  
specifically noted.  
LED Backlight  
The LED backlight in this product has a limited lifetime.  
* If the screen gets dark or does not turn on, it may be  
necessary to replace the LED backlight. This LED backlight  
is exclusive to this product and must be replaced by an  
authorized ASUS servicing dealer or service center.  
* Please contact your local ASUS servicing dealer or service  
center for assistance.  
E
MOUNTING PRECAUTIONS  
This product is for use indoors.  
A mounting bracket compliant with VESA specifications is  
required.  
When installing the monitor in  
landscape orientation, you can  
attach the supplied horizontal  
sticker (Operation buttons) to the  
right side.  
To install on a stand (commercially available) or on a wall, or to  
remove or move the monitor, consult your dealer.  
Mounting the monitor on the wall requires special expertise  
and the work must be performed by an authorized ASUS  
dealer. You should never attempt to perform any of this work  
yourself. Our company will bear no responsibility for accidents  
or injuries caused by improper mounting or mishandling.  
Use the monitor with the surface perpendicular to a level  
surface. If necessary, the monitor may be tilted up to 25  
degrees upward or 20 degrees downward.  
This monitor should be used at an ambient temperature  
between 32°F (0°C) and 104°F (40°C). Provide enough space  
around the monitor to prevent heat from accumulating inside.  
For the monitor in landscape orientation  
Unit: inch [cm]  
7-7/8 [20]  
*
2
[5]  
2
[5]  
2 [5]  
For the monitor in portrait orientation  
Unit: inch [cm]  
7-7/8 [20]  
*
2
[5]  
2
[5]  
2 [5]  
*
When you install this monitor on a wall, the monitor emits  
heat during operation, please be aware that this heat may  
discolor or alter the wall.  
If it is difficult to provide sufficient space for any reason such  
as the installation of the monitor inside a housing, or if the  
ambient temperature may be outside of the range of 32°F (0°C)  
to 104°F (40°C), install a fan or take other measures to keep the  
ambient temperature within the required range.  
Do not block any ventilation openings. If the temperature  
inside the monitor rises, this could lead to a malfunction.  
Do not place the monitor on a device which generates heat.  
E
Contents  
Supplied Components  
If any component should be missing, please contact your dealer.  
Liquid Crystal Display Monitor: 1  
Power cord: 1  
AC adapter: 1  
Setup Manual: 1  
DisplayPort cable: 1  
RS-232C conversion cable (Φ3.5 mini-jack): 1  
Pedestal (for stand): 1  
Strut (for stand): 1  
Attachment plate (for stand): 1 (preinstalled on monitor)  
Countersunk screws (M4 x 6 without washers): 5  
Screws (M4 x 10 with washers): 4  
Hex wrench: 1  
Cable clamp: 2  
Cable clamp (small): 1  
Cable clamp (large): 2  
Horizontal sticker (operation buttons): 1  
E
8
 
Part Names  
Front view  
n
1. LCD panel  
2. Power LED (See page 15.)  
1
2
Rear view  
n
1
2
4
5
13  
14  
15  
16  
17  
18  
19  
6
7
8
9
10 11  
12  
3
2
1. Speakers  
2. Vents  
3. Attachment plate (for stand)  
4. RS-232C input terminal (See page 12.)  
5. PC/AV HDMI 1 input terminal (See page 12.)  
6. PC/AV HDMI 2 input terminal (See page 12.)  
7. DisplayPort input terminal (See page 12.)  
8. Audio input terminal (See page 12.)  
9. Headphone terminal (See page 12.)  
10. AC input terminal (See page 13.)  
13. Power button ( ) (See page 16.)  
14. Brightness adjustment button ( ) (See page 16.)  
15. Brightness adjustment button ( ) (See page 16.)  
16. [VOL+/ ] button (See page 16.)  
17. [VOL-/ ] button (See page 16.)  
18. [MENU/ENTER] button (See page 16.)  
19. [INPUT/RETURN] button (See page 16.)  
11. Main power switch (See page 15.)  
12. Antitheft hole (  
)
E
9
 
Installing the stand (supplied)  
5. Fasten the stand to the monitor with the supplied screws  
CAUTION!  
(M4 x 10 with washers) (x4).  
Use the supplied hex wrench.  
Disconnect all cables from the monitor.  
Firmly tighten the installation screws (supplied) with the hex  
wrench (supplied).  
• Landscape  
Ensure that you have sufficient space to work.  
Screw  
(M4 x 10 with washers)  
Attaching the stand  
n
Remove all packaging materials before starting work.  
To prevent the table (etc.) from being damaged by the stand  
pedestal, spread a thick, soft cloth (blanket, etc.) and work on  
the cloth.  
1. Insert the stand strut into the packaging material (upper  
left) as shown.  
Packing material  
(upper left)  
Front  
2. While supporting the stand pedestal with your hand, fasten  
to the stand strut with the supplied countersunk screws (M4  
x 6 without washers) (x5).  
• Portrait  
Operation buttons  
Use the supplied hex wrench.  
Screw  
(M4 x 10 with washers)  
Countersunk screw  
(M4 x 6 without washers)  
Front  
1
2
Insert by hooking the tab  
Pedestal  
Fixing pin  
* A bag containing the screws  
(supplied) and hex wrench  
(supplied) is attached to the  
round hole in the stand pedestal.  
3. Spread a thick, soft cloth (blanket, etc.) that will prevent  
damage to the LCD panel on a stable flat surface where the  
entire monitor can be placed, and place the monitor with  
the LCD panel face down on the cloth.  
* If the monitor will be used in the portrait orientation, pull  
out the fixing pin (1), and insert it into the hole (2) as shown  
above.  
* To remove the stand, place the monitor and stand as shown  
above and remove the screws.  
4. Place the stand on the monitor.  
Hook the tab on the stand under the mounting plate (pre-  
installed on monitor).  
CAUTION!  
Adhere to the following when installing the monitor in its  
portrait orientation. Failing to adhere to the following may  
cause malfunctions.  
- Install the monitor such that the operation buttons are  
located on the top side.  
- Set the MONITOR on the MONITOR menu to PORTRAIT.  
(See page 20.)  
Tab  
E
10  
 
Installing the stand (supplied)  
Height/angle adjustment  
Adjusting the height  
n
Adjust to a height that is easy to view.  
Approx.  
5-29/32inch (15cm)  
NOTE:  
The height cannot be adjusted in a vertical installation.  
• Adjusting the angle  
Adjust to an angle that is easy to view.  
Approx.25°  
Approx.5°  
Approx.45°  
Approx.45°  
CAUTION!  
When moving the monitor, be sure to grasp only the frame.  
Grasping and applying pressure to the LCD panel may damage  
it.  
Take care not to pinch your fingers.  
If you are installing the monitor in landscape orientation, take  
caution when adjusting the angle at a raised height, so that it  
does not topple.  
E
11  
 
Connecting Peripheral Equipment  
1
2
3
4
5
6
4. DisplayPort input terminal  
CAUTION!  
Use the supplied DisplayPort cable.  
Select the audio input terminal to be used in DisplayPort of  
AUDIO SELECT on the SETUP menu.  
Be sure to turn off the main power switch and disconnect the  
plug from the power outlet before connecting/disconnecting  
cables. Also, read the manual of the equipment to be  
connected.  
When DisplayPort is selected, connection to the audio input  
terminal is unnecessary.  
Be careful not to confuse the input terminal with the output  
terminal when connecting cables. Accidentally reversing  
cables connected to the input and output terminals may cause  
malfunctions and the other problems.  
* Use the supplied cable.  
* If you need to extend the cable, consult your dealer.  
5. Audio input terminal  
Do not use any cable that has a damaged or deformed terminal.  
Using such a cable may cause malfunctions.  
Images may not be displayed properly depending on the  
computer (video cards), cables, or peripheral devices to be  
connected.  
Use a commercially available audio cable (mini stereo jack)  
without resistance.  
Set the audio input terminal used for each input mode in  
AUDIO SELECT on the SETUP menu.  
6. Headphone terminal  
NOTE:  
Use commercially available headphones (mini stereo jack).  
The output sound varies depending on the input mode.  
The volume can be adjusted using the volume adjustment.  
The audio input terminals used in each input mode are factory-  
set as follows.  
Audio input terminal  
(Factory setting)  
DisplayPort input terminal  
Input mode  
NOTE:  
DisplayPort  
HDMI1 [PC], HDMI1 [AV]  
HDMI2 [PC], HDMI2 [AV]  
The length of the signal cables or surrounding environment  
PC/AV HDMI input terminal  
may affect the image quality.  
Video output is disabled in the following cases:  
When the power is turned off  
When the monitor is in input signal waiting mode  
Connection with a PC or AV equipment  
1. RS-232C input terminal  
The monitor can be connected to a PC using the RS-232C  
conversion cable (supplied) and a commercially available  
RS-232 straight cable to control the monitor from the PC.  
2. PC/AV HDMI1 input terminal  
3. PC/AV HDMI2 input terminal  
Use a commercially available HDMI cable  
(High Speed cable compliant).  
Set HDMI1, HDMI2, or HDMI DUAL in INPUT SELECT on the  
SETUP menu according to the device to be connected.  
Select the audio input terminal to be used in HDMI1 [AV],  
HDMI1 [PC], HDMI2 [AV], or HDMI2 [PC] of AUDIO SELECT on  
the SETUP menu.  
When HDMI1 or HDMI2 is selected, connection to the audio  
input terminal is unnecessary.  
E
12  
 
Connecting the Power Cord  
CAUTION!  
Use only the power cord and AC adapter supplied with the monitor.  
1. Turn off the main power switch.  
2. Connect the AC adapter (supplied) to the power cord (supplied).  
3. Connect the AC adapter (supplied) to the AC input terminal.  
4. Plug of the power cord (supplied) into the AC power outlet.  
3
For power  
outlet  
4
AC input terminal  
2
Main power switch  
1
AC Adapter (Supplied)  
Power cord  
(Supplied)  
NOTE:  
Be sure to clamp the AC adapter cable (supplied) onto the cable clamp attachment using the supplied cable clamp.  
When clamping the AC adapter cable, take care not to stress the terminal of the AC adapter cable. Do not bend the AC adapter cable  
excessively.  
• Landscape  
• Portrait  
Cable clamp  
attachment  
Operation buttons  
Operation buttons  
Cable  
clamp  
attachment  
AC adapter cable (Supplied)  
AC adapter cable (Supplied)  
CAUTION!  
Do not fasten the supplied AC adapter to the monitor or other equipment.  
E
13  
 
Binding Cables  
Fastening the cables  
n
The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.  
Attach the cable clamps to the attachment parts on the back of the monitor and the stand, and bind the cables.  
Cable  
Cable clamp  
attachment  
Cable clamp  
Cable clamp (small)  
Cable clamp (large)  
Cable  
Cable  
Cable clamp  
attachment  
Cable clamp  
attachment  
Storing the cables  
n
The cables connected to the rear of the monitor can be bound using the cable clamp on the stand.  
• Landscape  
• Portrait  
Cable clamp (large)  
Cable  
Cable clamp  
attachment  
CAUTION!  
Do not forcibly bend or apply force to the cables. Risk of wire breakage or other damage.  
E
14  
 
Turning Power On/Off  
CAUTION!  
Turning power on/off  
Press the power button ( ) to turn the power ON/OFF.  
Turn on the monitor first before turning on the PC or playback  
device.  
Power button ( )  
Turning on the main power  
Power LED  
Power lamp status  
Green lit  
Status of the monitor  
Power on  
Main power switch  
Off  
Power off (Standby mode)  
Input signal waiting mode  
Orange lit  
CAUTION!  
When switching the main power switch or the power button  
) off and back on, always wait for at least 5 seconds. A short  
interval may result in a malfunction.  
CAUTION!  
(
The main power must be turned on/off with the main power  
switch. Do not connect/disconnect the power cord or turn the  
breaker on/off while the main power switch is on.  
When switching the main power switch or the power button  
NOTE:  
(
) off and back on, always wait for at least 5 seconds.  
When the main power switch is off, the monitor cannot be  
For a complete electrical disconnection, pull out the main plug.  
turned on.  
If the monitor is in the input signal standby mode and you  
press the power button ( ), the monitor enters standby mode.  
E
15  
 
Basic Operation  
6. [MENU/ENTER] button  
Displays and turns off the menu screen. (See page 18.)  
Settings can be entered when the menu screen is displayed.  
1
7. [INPUT/RETURN] button  
The input selection menu is displayed.  
Press the [VOL+/ ]/[VOL-/ ] buttons to select the input mode,  
and press [INPUT/RETURN] button to enter.  
2
3
Input mode  
DisplayPort  
Video  
Audio  
DisplayPort input terminal  
4
5
HDMI1 [PC]  
HDMI1 [AV]  
HDMI2 [PC]  
HDMI2 [AV]  
PC/AV HDMI input terminal*1  
PC/AV HDMI input terminal*2  
*3  
When HDMI DUAL is set to ON  
6
7
Input mode  
Video  
Audio  
*3  
*5  
DisplayPort  
DisplayPort input terminal  
HDMI DUAL [PC]*4  
HDMI DUAL [AV]*4  
PC/AV HDMI input terminal*4  
*1 Select the terminal to be used in HDMI1 of INPUT SELECT.  
(See page 20.)  
*2 Select the terminal to be used in HDMI2 of INPUT SELECT.  
(See page 20.)  
1. Power button (  
)
Press this button to turn the power ON/OFF.  
*3 Select the terminal for AUDIO SELECT which is used for audio  
input. (See page 20.)  
*4 Same as the HDMI1 terminal setting.  
*5 Same as the AUDIO SELECT of HDMI1.  
2,3. Brightness adjustment button (  
The brightness menu appears.  
/
)
B R I G H T  
15  
In a menu screen, returns the cursor to the previous screen.  
Adjust the brightness with the brightness adjustment button  
).  
* If you do not press any buttons for about 4 seconds, the BRIGHT