Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with manufacturer’s instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian Department
of Communications.
This class B digital apparatus complies with Canadian ICES-003.
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components as well as the packaging
information in different regions.
vi
REACH
Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of
Chemicals) regulatory framework, we published the chemical substances in our products at
DO NOT throw the motherboard in municipal waste. This product has been designed to
enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin
indicates that the product (electrical and electronic equipment) should not be placed in
municipal waste. Check local regulations for disposal of electronic products.
DO NOT throw the mercury-containing button cell battery in municipal waste. This symbol
of the crossed out wheeled bin indicates that the battery should not be placed in municipal
waste.
Safety information
Electrical safety
•
To prevent electric shock hazard, disconnect the power cable from the electric outlet
before relocating the system.
•
When adding or removing devices to or from the system, ensure that the power cables
for the devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.
•
•
•
Before connecting or removing signal cables from the motherboard, ensure that all
power cables are unplugged.
Seek professional assistance before using an adapter or extension cord. These devices
could interrupt the grounding circuit.
Ensure that your power supply is set to the correct voltage in your area. If you are not
sure about the voltage of the electrical outlet you are using, contact your local power
company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified service
technician or your retailer.
Operation safety
•
•
•
•
Before installing the motherboard and adding devices on it, carefully read all the manuals
that came with the package.
Before using the product, ensure that all cables are correctly connected and the power
cables are not damaged. If you detect any damage, contact your dealer immediately.
To avoid short circuits, keep paper clips, screws, and staples away from connectors,
slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Do not place the product in any area
where it may become wet.
•
•
Place the product on a stable surface.
If you encounter technical problems with the product, contact a qualified service
technician or your retailer.
vii
About this guide
This user guide contains the information you need when installing and configuring the
motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it
supports.
•
Chapter 2: BIOS information
This chapter tells how to change system settings through the BIOS Setup menus.
Detailed descriptions of the BIOS parameters are also provided.
Conventions used in this guide
To ensure that you perform certain tasks properly, take note of the following symbols used
throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying to
complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Where to find more information
Refer to the following sources for additional information and for product and software
updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and software
products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty flyers,
that may have been added by your dealer. These documents are not part of the
standard package.
Typography
Bold text
Italics
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key.
Example: <Enter> means that you must press the Enter or
Return key.
<Key1>+<Key2>+<Key3>
If you must press two or more keys simultaneously, the key
names are linked with a plus sign (+).
Example: <Ctrl>+<Alt>+<D>
viii
E45M1-I DELUXE specifications summary
CPU
AMD® Dual-Core processor E-450 with AMD RadeonTM HD 6320
Discrete-Class Graphics
Support AMD® Turbo Core Technology
Chipset
Memory
AMD® FCH A50M (Hudson M1)
2 x DDR3 1333/1066 MHz, max. 8GB, non-ECC, un-buffered
memory
Single-channel memory architecture
*
Vendors List).
** When you install a total memory of 4GB capacity or more,
Windows® 32-bit operating system may only recognize less
than 3GB. We recommend a maximum of 3GB system
memory if you are using a Windows® 32-bit operating system.
Expansion slots
Graphics
1 x PCI Express 2.0 x16 slot (at x4 mode, with latch)
Integrated AMD® Radeon HD 6320 Discrete-Class Graphics
Supports DVI with max. resolution up to 1920 x 1200 @60Hz
Supports HDMI with max. resolution up to 1920 x 1080 @60Hz
Storage
5 x Serial ATA 6.0 Gb/s connectors support AHCI mode
1 x eSATA 6.0 Gb/s connectors
LAN
Realtek® 8111E PCIe Gigabit LAN controller
Bluetooth
Bluetooth V3.0+ HS
ASUS BT GO! Utility
Audio
USB
ALC892 8-channel* High Definition Audio CODEC
Supports DTS Surround Sensation Ultra-PC
*
Use a chassis with HD audio module in the front panel to
support an 8-channel audio output.
NEC® USB 3.0 controller :
4 x USB 3.0/2.0 ports (2 ports at the mid-board, 2 ports at the back
panel [blue])
AMD® FCH A50M Chipset:
8 x USB 2.0 ports (4 ports at the mid-board, 4 ports at the back
panel)
ASUS special
features
Turbo Key II
AI Suite II
MemOK!
Anti-Surge protection
ASUS Q-Fan
ASUS BT GO!
ASUS CrashFree BIOS 3
ASUS EZ Flash 2
ASUS @Vibe support
ASUS UEFI BIOS EZ Mode featuring friendly graphics user
interface
100% All High-quality Conductive Polymer Capacitors
ASUS MyLogo2
(continued on the next page)
ix
E45M1-I DELUXE specifications summary
Rear panel ports
1 x PS/2 Keyboard / Mouse combo port
1 x DVI-I port
1 x HDMI port
1 x eSATA 6.0Gb/s port
1 x LAN (RJ-45) port
4 x USB 2.0 ports
2 x USB 3.0/2.0 port (blue, compatible with USB 2.0 devices)
1 x Optical S/PDIF out port
1 x Bluetooth 3.0 adapter
2 x Wi-Fi antenna ports
3 x Audio jacks
Internal connectors/ 1 x USB 3.0/2.0 connectors support additional 2 USB 3.0/2.0 ports
switches
(20-1 pin)
2 x USB 2.0 connectors support additional 4 USB 2.0 ports
1 x CPU fan connector
1 x Chassis fan connector
1 x Chassis intrusion connector
5 x SATA 6.0Gb/s connectors
1 x S/PDIF Out connector
1 x System panel connector
1 x Front panel audio connector
1 x 24-pin EATX power connector
1 x 4-pin ATX 12V power connector
1 x MemOK! switch
1 x Turbo Key II switch
BIOS features
Accessories
32 Mb Flash ROM, AMI BIOS, PnP, DMI 2.0, WfM 2.0, ACPI 2.0a,
SM BIOS 2.6
2 x Serial ATA 6.0Gb/s cables
2 x Wi-Fi antennas
1 x I/O shield
1 x User Manual
1 x Support DVD
Support DVD
Form factor
Drivers
ASUS utilities
ASUS Update
Anti-virus software (OEM version)
Mini ITX form factor: 6.7 in x 6.7 in (17.0 cm x 17.0 cm)
* Specifications are subject to change without notice.
x
Chapter 1
Product introduction
Thank you for buying an ASUS® E45M1-I DELUXE motherboard!
Before you start installing the motherboard, and hardware devices on it, check the items in
your motherboard package. Refer to page x for the list of accessories.
If any of the items is damaged or missing, contact your retailer.
1.1
Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
•
Unplug the power cord from the wall socket before touching any component.
Before handling components, use a grounded wrist strap or touch a safely grounded
object or a metal object, such as the power supply case, to avoid damaging them due to
static electricity.
•
•
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the
bag that came with the component.
•
Before you install or remove any component, ensure that the ATX power supply is
switched off or the power cord is detached from the power supply. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
Chapter 1: Product introduction
1-1
1.2
Motherboard overview
1.2.1
Motherboard layout
Ensure that you install the motherboard into the chassis in the correct orientation. The edge
with external ports goes to the rear part of the chassis.
1
2
3
4
5
6
7
8
17cm(6.7in)
CLRTC
TURBO_KEY_II
USB3_34
O2LED2
ATX12V
EPU
NEC
KB_USB34
USB3.0
CHA_FAN
Super
I/O
CPU_FAN
AMD® E-450
Processor with
RadeonTM HD
6320 Graphics
AMD®
Hudson M1
ESATA6G
_USB12
_BT
NEC
USB3.0
MemOK!
5
9
DRAM_LED
SATA6G_2
SATA6G_1
SATA6G_3
SATA6G_5
32Mb
BIOS
RTL
8111E
SATA6G_4
LAN1_USB3_12
AUDIO
USB78
USB56
WLAN
AAFP
SB_PWR
ALC
892
PCIEX16
CHASSIS
SPDIF_OUT
17 16
15 14
13
12 11
10
Place four screws into the holes indicated by circles to secure the motherboard to the
chassis. DO NOT overtighten the screws! Doing so can damage the motherboard.
1.2.2
Layout contents
Connectors/Jumpers/Slots/LED
Page
Connectors/Jumpers/Slots/LED
Page
1.
CPU and chassis fan connectors (3-pin
CPU_FAN, 3-pin CHA_FAN)
1-12 10. Chassis intrusion connector (4-1 pin CHASSIS)
1-14
2.
3.
USB 3.0 connector (20-1 pin USB3_34)
Turbo Key II LED (O2LED2)
1-15 11. MemOK! switch
1-17
1-18
1-18 12. DARM LED (DRAM_LED)
4.
5.
Turbo Key II switch
1-16 13. USB 2.0 connectors (10-1 pin USB56, USB78)
1-15
1-13
ATX power connectors (24-pin EATXPWR,
4-pin ATX12V)
1-11 14. Serial ATA 6.0Gb/s connectors (7-pin
SATA6G_1~5)
6.
7.
8.
9.
Clear RTC RAM (3-pin CLRTC)
AMD® Zacate™ 18W processor
DDR3 DIMM slots
1-8
1-3
1-3
1-14
15. Standby power LED (SB_PWR)
1-18
1-12
1-13
16. Digital audio connector (4-1 pin SPDIF_OUT)
17. Front panel audio connector (10-1 pin AAFP)
System panel connector (10-1 pin F_PANEL)
1-2
ASUS E45M1-I DELUXE
1.3
Central Processing Unit (CPU)
The motherboard comes with an onboard AMD® Dual-Core Processor E-450 with AMD
RadeonTM HD 6320 Discrete-Class Graphics and a specially designed CPU heatsink.
AMD® Dual-Core Processor E-450
E45M1-I DELUXE AMD® E-450 processor
1.4
System memory
1.4.1
Overview
The motherboard comes with two Double Data Rate 3 (DDR3) Dual Inline Memory Modules
(DIMM) sockets.
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched
differently to prevent installation on a DDR2 DIMM socket. DDR3 modules are developed for
better performance with less power consumption.
The figure illustrates the location of the DDR3 DIMM sockets:
Channel
Sockets
Channel A
DIMM1 and DIMM2
E45M1-I DELUXE 240-pin DDR3 DIMM sockets
Chapter 1: Product introduction
1-3
1.4.2
Memory configurations
You may install 512MB, 1GB, 2GB, and 4GB unbuffered non-ECC DDR3 DIMMs into the
DIMM sockets.
•
•
We recommend that you install the memory modules from the blue slots for better
overclocking capability.
Due to the memory address limitation on 32-bit Windows® OS, when you install 4GB
or more memory on the motherboard, the actual usable memory for the OS can be
about 3GB or less. For effective use of memory, we recommend that you do any of the
following:
- Use a maximum of 3GB system memory if you are using a 32-bit Windows® OS.
- Install a 64-bit Windows® OS when you want to install 4GB or more on the
motherboard.
•
•
This motherboard does not support DIMMs made up of 512Mb (64MB) chips or less.
The default memory operation frequency is dependent on its Serial Presence Detect
(SPD), which is the standard way of accessing information from a memory module.
Under the default state, some memory modules for overclocking may operate at a
lower frequency than the vendor-marked value. To operate at the vendor-marked or at a
higher frequency, refer to section 2.4 Ai Tweaker menu for manual memory frequency
adjustment.
•
For system stability, use a more efficient memory cooling system to support a full
memory load (2 DIMMs) or overclocking condition.
E45M1-I DELUXE Motherboard Qualified Vendors Lists (QVL)
DDR3-1066 MHz capability
DIMM socket support
(Optional)
SS/
DS
Chip
Brand
Vendors
Crucial
Part No.
Size
Chip NO.
Timing
Voltage
1 DIMM
2 DIMM
CT12864BA1067.8FF
CT25664BA1067.16FF
EBJ10UE8EDF0-AE-F
EBJ21UE8EDF0-AE-F
1GB
2GB
1GB
2GB
1GB
2GB
4GB
1GB
SS
Micron
Micron
9GF22D9KPT
9HF22D9KPT
7
-
-
•
•
•
•
•
•
•
•
•
•
•
Crucial
ELPIDA
ELPIDA
DS
SS
DS
SS
DS
DS
SS
DS
DS
7
-
•
•
•
•
•
•
•
•
•
ELPIDA J1108EDSE-DJ-F
ELPIDA J1108EDSE-DJ-F
ELPIDA J1108BFSE-DJ-F
ELPIDA J1108BDSE-DJ-F
1.35V(low voltage)
-
1.35V(low voltage)
KINGSTON KVR1066D3N7/1G(矮版)
KINGSTON KVR1066D3N7/2G
KINGSTON KVR1066D3N7/4G
7
7
7
7
7
-
1.5V
1.5V
Hynix
H5TQ2G83AFR
9GF22D9KPT
1.5V
Micron
MT8JTF12864AZ-1G1F1
Micron
Micron
Hynix
-
-
-
Micron
MT16JTF25664AZ-1G1F1 2GB
2GB DIMM PC3-8500 2GB
9HF22D9KPT
Kingtiger
H5TQ1G83AFP G7C
1-4
ASUS E45M1-I DELUXE
DDR3-1333 MHz capability
DIMM socket
support
(Optional)
SS/
DS
Vendors
Part No.
Size
Chip Brand
Chip NO.
Timing
Voltage
1 DIMM 2 DIMM
AD30908C8D-151C
E0906
A-Data
AD31333001GOU
1GB
2GB
SS A-Data
SS A-Data
-
-
-
-
•
•
A-Data
A-Data
AD63I1B0823EV
3CCA-1509A
-
•
•
•
•
AD31333G001GOU
3GB(3 x 1GB)
SS
SS
DS
-
-
-
8-8-8-24
1.65-1.85V
1.25V-1.35V(low
voltage)
A-Data
AXDU1333GC2G9-2G(XMP)
4GB(2 x 2GB)
-
9-9-9-24
•
•
A-Data
AD31333G002GMU
AD63I1C1624EV
78.A1GC6.9L1
2GB
-
8-8-8-24
1.65-1.85V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
A-Data
4GB
DS A-Data
DS Apacer
DS Apacer
DS Apacer
3CCA-1509A
-
-
Apacer
Apacer
Apacer
CORSAIR
CORSAIR
CORSAIR
CORSAIR
CORSAIR
Crucial
2GB
AM5D5808DEWSBG
-
-
78.A1GC6.9L1
2GB
AM5D5808FEQSBG
9
-
78.B1GDE.9L10C
CM3X1024-1333C9
TR3X3G1333C9 G
TR3X6G1333C9 G
4GB
AM5D5908CEHSBG
-
-
1GB
SS
SS
SS
DS
DS
-
-
-
-
-
-
9-9-9-24
1.60V
3GB(3 x 1GB)
6GB(3x 2GB)
-
9-9-9-24
1.50V
-
9-9-9-24
1.50V
CMD24GX3M6A1333C9(XMP) 24GB(6x4GB)
-
9-9-9-24
1.60V
TW3X4G1333C9D G
4GB(2 x 2GB)
1GB
-
9-9-9-24
1.50V
CT12864BA1339.8FF
SS Micron
DS Micron
9FF22D9KPT
9
-
Crucial
CT25664BA1339.16FF
BL25664BN1337.16FF (XMP)
EBJ10UE8EDF0-DJ-F
2GB
9KF27D9KPT
9
-
Crucial
6GB(3 x 2GB)
1GB
DS
-
-
7-7-7-24
1.65V
ELPIDA
ELPIDA
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
G.SKILL
GEIL
SS ELPIDA
DS ELPIDA
SS G.SKILL
J1108EDSE-DJ-F
-
1.35V(low voltage)
EBJ21UE8EDF0-DJ-F
2GB
J1108EDSE-DJ-F
-
1.35V(low voltage)
F3-10600CL8D-2GBHK(XMP)
F3-10600CL9D-2GBNQ
F3-10666CL7T-3GBPK(XMP)
1GB
-
-
-
2GB(2 x 1GB)
3GB(3 x 1GB)
SS
SS
DS
DS
DS
DS
DS
-
-
-
-
-
-
-
-
9-9-9-24
7-7-7-18
1.5V
-
1.5~1.6V
F3-10666CL8D-4GBECO(XMP) 4GB(2 x 2GB)
-
8-8-8-8-24 XMP 1.35V
F3-10666CL7T-6GBPK(XMP)
F3-10666CL7D-8GBRH(XMP)
GET316GB1333C9QC
GV32GB1333C9DC
6GB(3 x 2GB)
8GB(2 x 4GB)
16GB(4x 4GB)
2GB(2 x 1GB)
4GB(2 x 2GB)
4GB(2 x 2GB)
4GB(2 x 2GB)
1GB
-
7-7-7-18
1.5~1.6V
-
7-7-7-21
1.5V
-
9-9-9-24
1.5V
GEIL
-
9-9-9-24
1.5V
GEIL
GG34GB1333C9DC
DS GEIL
GL1L128M88BA12N
-
9-9-9-24
1.3V(low voltage)
GEIL
GV34GB1333C9DC
DS
DS
-
-
9-9-9-24
1.5V
GEIL
GVP34GB1333C7DC
HMT112U6TFR8A-H9
HMT325U6BFR8C-H9
HMT125U6TFR8A-H9
HMT351U6BFR8C-H9
FLFD45F-B8KL9 NAES
FLFE85F-C8KF9 CAES
FLFE85F-C8KL9 NAES
FLFE85F-C8KM9 NAES
FLFE85F-B8KL9 NEES
FLFF65F-C8KL9 NEES
FLFF65F-C8KM9 NEES
-
7-7-7-24
1.5V
Hynix
SS Hynix
SS Hynix
DS Hynix
DS Hynix
SS Kingmax
SS Kingmax
H5TC1G83TFRH9A
H5TQ2G83BFRH9C
H5TC1G83TFRH9A
H5TQ2G83BFRH9C
KKB8FNWBFGNX-27A
KFC8FMFXF-DXX-15A
-
1.35V(low voltage)
Hynix
2GB
-
-
Hynix
2GB
-
1.35V(low voltage)
Hynix
4GB
-
-
Kingmax
Kingmax
KINGMAX
Kingmax
Kingmax
KINGMAX
Kingmax
1GB
-
-
2GB
-
-
2GB
SS KINGMAX KFC8FNLXF-DXX-15A
-
-
2GB
SS Kingmax
DS Kingmax
KFC8FNMXF-BXX-15A
KKB8FNWBFGNX-26A
-
-
2GB
-
-
4GB
DS KINGMAX KFC8FNLXF-DXX-15A
-
-
4GB
DS Kingmax
SS ELPIDA
SS Hynix
KFC8FNMXF-BXX-15A
-
-
KINGSTON KVR1333D3N9/1G(矮矮)
KINGSTON KVR1333D3N9/2G(矮矮)
KINGSTON KVR1333D3N9/2G(矮矮)
KINGSTON KVR1333D3N9/2G
1GB
J1108BDBG-DJ-F
9
1.5V
2GB
H5TQ2G83AFRH9C
9
-
2GB
DS ELPIDA
DS KTC
J1108BFBG-DJ-F
9
1.5V
1.5V
1.5V
1.65V
XMP 1.25V
1.5V
1.5V
1.5V
-
2GB
D1288JPNDPLD9U
9
KINGSTON KVR1333D3N9/2G
2GB
DS ELPIDA
J1108BDSE-DJ-F
9
KINGSTON KHX1333C7D3K2/4GX(XMP)
4GB(2 x 2GB)
DS
DS
-
-
-
7
KINGSTON KHX1333C9D3UK2/4GX(XMP) 4GB(2 x 2GB)
-
9
KINGSTON KVR1333D3N9/4G(矮矮)
KINGSTON KVR1333D3N9/4G(矮矮)
KINGSTON KVR1333D3N9/4G
KINGSTON KVR1333D3N9/4G
4GB
DS ELPIDA
DS ELPIDA
DS KTC
J2108BCSE-DJ-F
9
4GB
J2108BCSE-DJ-F
-
4GB
D2568JENCNGD9U
-
4GB
DS Hynix
SS Micron
SS Micron
SS Micron
DS Micron
DS Micron
H5TQ2G83AFR
-
Micron
Micron
Micron
Micron
Micron
OCZ
MT4JTF12864AZ-1G4D1
MT8JTF12864AZ-1G4F1
MT8JTF25664AZ-1G4D1
MT16JTF25664AZ-1G4F1
MT16JTF51264AZ-1G4D1
OCZ3F13334GK
1GB
OJD12D9LGQ
-
-
1GB
9FF22D9KPT
9
-
2GB
OJD12D9LGK
-
-
2GB
9KF27D9KPT
9
-
4GB
OLD22D9LGK
-
-
4GB(2 x 2GB)
4GB(2 x 2GB)
4GB(2 x 2GB)
4GB(2 x 2GB)
6GB(3 x 2GB)
6GB(3 x 2GB)
DS
DS
DS
DS
DS
DS
-
-
-
-
-
-
-
-
-
-
-
-
9-9-9-20
7-7-7-20
7-7-7-20
7-7-7-20
9-9-9-20
7-7-7-20
1.7V
1.8V
1.65V
1.75V
1.65V
1.65V
OCZ
OCZ3P13334GK
OCZ
OCZ3P1333LV4GK
OCZ
OCZ3X13334GK(XMP)
OCZ3G1333LV6GK
OCZ
•
OCZ
OCZ3P1333LV6GK
(continued on the next page)
Chapter 1: Product introduction
1-5
DDR3-1333 MHz capability
DIMM socket
support
(Optional)
SS/
DS
Vendors
Part No.
Size
Chip Brand
Chip NO.
Timing
Voltage
1 DIMM 2 DIMM
OCZ
OCZ3X1333LV6GK(XMP)
AL7F8G73F-DJ2
6GB(3 x 2GB)
1GB
DS
-
-
8-8-8-20
1.60V
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PSC
SS PSC
DS PSC
A3P1GF3FGF
A3P1GF3FGF
-
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PSC
AL8F8G73F-DJ2
2GB
-
-
SAMSUNG
SAMSUNG
SAMSUNG
SAMSUNG
M378B2873FHS-CH9
M378B5773DH0-CH9
M378B5673FH0-CH9
M378B5273CH0-CH9
1GB
SS SAMSUNG K4B1G0846F
SS SAMSUNG K4B2G0846D
DS SAMSUNG K4B1G0846F
DS SAMSUNG K4B2G0846C
-
-
2GB
-
-
2GB
-
-
4GB
-
-
Super Talent W1333UA1GH
Super Talent W1333X2G8(XMP)
Super Talent W1333UB2GS
Super Talent W1333UB4GS
Super Talent W1333UX6GM
1GB
SS Hynix
SS
H5TQ1G83TFR
-
9
-
1GB
-
8
-
2GB
DS SAMSUNG K4B1G0846F
DS SAMSUNG K4B2G0846C
9
-
4GB
-
-
6GB(3x 2GB)
2GB
DS Micron
SS Micron
SS Hynix
0BF27D9KPT
9-9-9-24
1.5V
Transcend
Transcend
Transcend
Transcend
Century
Century
Elixir
JM1333KLN-2G
0YD77D9LGK
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
JM1333KLN-2G
2GB
H5TQ2G83BZRH9C
JM1333KLU-2G
2GB
DS Transcend TK243PDF3
TS256MLK64V3U
2GB
DS Micron
SS Micron
DS Micron
SS Elixir
9GF27D9KPT
PC3-10600 DDR3-1333 9-9-9
PC3-10600 DDR3-1333 9-9-9
M2F2G64CB88B7N-CG
M2F2G64CB88D7N-CG
M2F4G64CB8HB5N-CG
M2F4G64CB8HD5N-CG
1GB
8FD22D9JNM
2GB
8DD22D9JNM
2GB
N2CB2G80BN-CG
N2CB2G80DN-CG
N2CB2G80BN-CG
N2CB2G80DN-CG
PM128M8D385-15
Elixir
2GB
SS Elixir
Elixir
4GB
DS Elixir
Elixir
4GB
DS Elixir
KINGSHARE KSRPCD313332G
2GB
DS PATRIOT
SEC 904 HCH9
K4B1G0846D
Kingtiger
Kingtiger
2GB DIMM PC3-10666
KTG2G1333PG3
2GB
DS SAMSUNG
-
-
•
•
2GB
DS
DS MICRON
DS
DS PATRIOT
-
-
-
-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
KINGTIGER 4GB DIMM PC3-10600(矮矮)
4GB
ICD77D9LGK
-
-
PATRIOT
PATRIOT
PATRIOT
PATRIOT
RAMAXEL
RiDATA
PSD31G13332H
1GB
-
-
9
-
PSD31G13332
1GB
PM64M8D38U-15
-
-
PSD32G13332H
2GB
DS
DS
-
-
-
-
-
PDC34G1333ELK
RMR1870ED48E8F-1333
C304627CB1AG22Fe
E304459CB1AG32Cf
4GB(2 x 2GB)
2GB
-
9-9-9-24
1.5V
DS ELPIDA
DS RiDATA
DS RiDATA
J1108BDBG-DJ-F
-
-
-
-
2GB
N/A
N/A
9
9
RiDATA
4GB
SILICON
POWER
SP001GBLTU133S01
SP001GBLTU133S02
SP002GBLTU133S02
1GB
1GB
2GB
SS NANYA
SS Elixir
DS Elixir
NT5CB128M8AN-CG
N2CB1680AN-C6
N2CB1680AN-C6
9
9
9
-
-
-
•
•
•
•
SILICON
POWER
SILICON
POWER
•
•
•
•
TAKEMS
TAKEMS
TAKEMS
TAKEMS
TAKEMS
UMAX
TMS1GB364D081-107EY
TMS1GB364D081-138EY
TMS2GB364D081-107EY
TMS2GB364D081-138EY
TMS2GB364D082-138EW
E41302GP0-73BDB
1GB
1GB
2GB
2GB
2GB
2GB
2GB
2GB
SS
SS
DS
DS
DS
-
-
-
-
-
-
7-7-7-20
1.5V
1.5V
1.5V
1.5V
1.5V
-
-
8-8-8-24
-
7-7-7-20
•
•
•
•
•
•
•
•
•
•
•
•
-
8-8-8-24
-
8-8-8-24
DS UMAX
DS Hynix
DS AMPO
U2S24D30TP-13
H5TQ1G83AFP
AM3420803-13H
-
-
-
V-Color
TD2G16C9-Z8
-
WINTEC
3WVS31333-2G-CNR
-
SS: Single-sided / DS: Double-sided
DIMM support:
•
1 DIMM: Supports one module inserted into any slot as single-channel memory
configuration.
1-6
ASUS E45M1-I DELUXE
1.5
Expansion slots
In the future, you may need to install expansion cards. The following sub-sections describe
the slots and the expansion cards that they support.
Unplug the power cord before adding or removing expansion cards. Failure to do so may
cause you physical injury and damage motherboard components.
1.5.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with it and
make the necessary hardware settings for the card.
2.
3.
Remove the system unit cover (if your motherboard is already installed in a chassis).
Remove the bracket opposite the slot that you intend to use. Keep the screw for later
use.
4.
Align the card connector with the slot and press firmly until the card is completely
seated on the slot.
5.
6.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
1.5.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See Chapter 2 for
information on BIOS setup.
2.
3.
Assign an IRQ to the card.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share IRQ” or that
the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI
groups, making the system unstable and the card inoperable.
1.5.3
PCI Express x16 slot
This motherboard has a PCI Express 2.0 x16 slot that supports PCI Express 2.0 x16 graphic
cards complying with the PCI Express specifications.
Chapter 1: Product introduction
1-7
1.6
Jumpers
Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can
clear the CMOS memory of date, time, and system setup parameters by erasing
the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in
CMOS, which include system setup information such as system passwords.
CLRTC
1
2
2
3
Normal
Clear RTC
(Default)
E45M1-I DELUXE Clear RTC RAM
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3
for about 5-10 seconds, then move the cap back to pins 1-2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter
data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default
position. Removing the cap will cause system boot failure!
•
•
If the steps above do not help, remove the onboard battery and move the jumper again
to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.
You do not need to clear the RTC when the system hangs due to overclocking. For
system failure due to overclocking, use the CPU Parameter Recall (C.P.R.) feature. Shut
down and reboot the system, then the BIOS automatically resets parameter settings to
default values.
1-8
ASUS E45M1-I DELUXE
1.7
Connectors
1.7.1
Rear panel connectors
1
2
3
4
5
6
7 8
14
13
12
11
10
9
1.
2.
WLAN antenna ports. These ports connect to the WLAN antennas.
PS/2 Keyboard / Mouse Combo port. This port is for a PS/2 keyboard or PS/2
mouse.
3.
4.
Optical S/PDIF output port. This port connects to an external audio output device via
an optical S/PDIF cable.
Onboard Bluetooth module. This onboard Bluetooth module allows wireless
connection and data transfer between your system and other Bluetooth devices.
•
•
Under Windows® 7 OS, to achieve the complete Bluetooth functions, download the latest
Bluetooth Electrical Specification:
Bluetooth specification V3.0 compliant;
Transmission rate up to 24 Mbps;
Working distance up to 10 meters;
Intergrated 32-bit CPU with 32KB data RAM and 256KB program RAM;
5V single supply voltage.
•
Under Windows® XP, if the Bluetooth Driver item is not displayed on the Support DVD’s
Drivers screen, follow the steps below:
1. Shut down your computer and switch off the Power Supply Unit (PSU).
2. Switch on the PSU and boot up your computer.
3. Open the Support DVD and click ASUS InstAll.
5.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are for USB
2.0/1.1 devices.
Chapter 1: Product introduction
1-9
6.
LAN (RJ-45) port. This port allows Gigabit connection to a Local Area Network (LAN)
through a network hub. Refer to the table below for the LAN port LED indications.
LAN port LED indications
Speed
LED
Activity Link
LED
ACT/LINK LED
Description
No link
SPEED LED
Status
OFF
Status
Description
OFF
10 Mbps connection
ORANGE
Linked
ORANGE 100 Mbps connection
GREEN 1 Gbps connection
BLINKING Data activity
LAN port
7.
8.
Line In port (light blue). This port connects the tape, CD, DVD player, or other audio
sources.
Line Out port (lime). This port connects to a headphone or a speaker. In 4-channel,
6-channel, and 8-channel configurations, the function of this port becomes Front
Speaker Out.
9.
Microphone port (pink). This port connects a microphone.
Refer to the audio configuration table below for the function of the audio ports in the 2, 4, 6,
or 8-channel configuration.
Audio 2, 4, 6, 8-channel configuration
Port
Headset 2-channel
4-channel
Rear Speaker Out
Front Speaker Out
Mic In
6-channel
Rear Speaker Out
Front Speaker Out
Bass/Center
-
8-channel
Light Blue (Rear panel)
Lime (Rear panel)
Pink (Rear panel)
Lime (Front panel)
Line In
Line Out
Mic In
-
Rear Speaker Out
Front Speaker Out
Bass/Center
-
Side Speaker Out
To configure an 8-channel audio output:
Use a chassis with HD audio module in the front panel to support an 8-channel audio
output.
10. USB 3.0 ports 1 and 2. These two 9-pin Universal Serial Bus (USB) ports are for USB
3.0/2.0 devices.
•
•
DO NOT connect a keyboard / mouse to any USB 3.0 port when installing Windows®
operating system.
Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows®
OS environment and after the USB 3.0 driver installation.
•
•
USB 3.0 devices can only be used as data storage only.
We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster
and better performance for your USB 3.0 devices.
1-10
ASUS E45M1-I DELUXE
11. eSATA port. This port connects to an external Serial ATA hard disk drive.
12. DVI-I port. This port is for any DVI-I compatible device and are HDCP compliant,
allowing playback of HD DVD, Blu-Ray and other protected content.
13. HDMI port. This port is for a High-Definition Multimedia Interface (HDMI) connector,
and is HDCP compliant allowing playback of HD DVD, Blu-ray, and other protected
content.
14. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are
available for connecting USB 2.0/1.1 devices.
1.7.2
Internal connectors
1.
ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are
designed to fit these connectors in only one orientation. Find the proper orientation and
push down firmly until the connectors completely fit.
ATX12V
EATXPWR
PIN 1
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
GND
GND
+12V DC
+12V DC
GND
GND
+5 Volts
+5 Volts
+5 Volts
-5 Volts
GND
+5 Volts
GND
GND
GND
+5 Volts
GND
PSON#
GND
+3 Volts
+3 Volts
-12 Volts
+3 Volts
PIN 1
E45M1-I DELUXE ATX power connectors
•
For a fully configured system, we recommend that you use a power supply unit (PSU)
that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum
power of 350 W.
•
DO NOT forget to connect the 4-pin ATX +12V power plug. Otherwise, the system will
not boot up.
•
We recommend that you use a PSU with higher power output when configuring a
system with more power-consuming devices. The system may become unstable or may
not boot up if the power is inadequate.
•
If you are uncertain about the minimum power supply requirement for your system,
com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for details.
Chapter 1: Product introduction
1-11
2.
CPU and chassis fan connectors (3-pin CPU_FAN, 3-pin CHA_FAN)
Connect the fan cables to the fan connectors on the motherboard, ensuring that the
black wire of each cable matches the ground pin of the connector.
CHA_FAN
Rotation
+12V
GND
CPU_FAN
Rotation
+12V
GND
E45M1-I DELUXE Fan connectors
Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the
system may damage the motherboard components. These are not jumpers! Do not place
jumper caps on the fan connectors!
•
•
The CPU_FAN connector supports a CPU fan of maximum 2A (24 W) fan power.
Only the CPU_FAN connector supports the ASUS Q-Fan feature.
3.
Digital audio connector (4-1 pin SPDIF_OUT)
This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port. Connect
the S/PDIF Out module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
SPDIF_OUT
E45M1-I DELUXE Digital audio connector
The S/PDIF module is purchased separately.
1-12
ASUS E45M1-I DELUXE
4.
Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~5)
These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0
Gb/s signal cables.
SATA6G_2
SATA6G_4
SATA6G_1
SATA6G_3
SATA6G_5
E45M1-I DELUXE SATA 6.0Gb/s connectors
•
•
These connectors are set to [IDE Mode] by default. In IDE mode, you can connect Serial
ATA boot/data hard disk drives to these connectors.
When using hot-plug and NCQ, set the OnChip SATA Type item in the BIOS to [AHCI
Mode]. See section 2.5.2 SATA Configuration for details.
5.
Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports
either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel
audio I/O module cable to this connector.
AAFP
PIN 1
PIN 1
PORT1 L
PORT1 R
PORT2 R
GND
PRESENCE#
SENSE1_RETUR Line out_R
NC
SENSE2_RETUR Line out_L
MIC2
MICPWR
AGND
NC
NC
SENSE_SEND
PORT2 L
NC
HD-audio-compliant
pin definition
Legacy AC’97
compliant definition
E45M1-I DELUXE Front panel audio connector
•
We recommend that you connect a high-definition front panel audio module to this
connector to avail of the motherboard’s high-definition audio capability.
•
If you want to connect a high-definition front panel audio module to this connector, set
the Front Panel Type item in the BIOS setup to [HD]. If you want to connect an AC'97
front panel audio module to this connector, set the item to [AC97]. By default, this
connector is set to [HD]. See section 2.5.5 Onboard Devices Configuration for details.
Chapter 1: Product introduction
1-13
6.
System panel connector (10-1 pin F_PANEL)
This connector supports several chassis-mounted functions.
F_PANEL
Reset
Ground
GND
PWR
IDE_LED-
IDE_LED+
PLED-
PLED+
PIN 1
E45M1-I DELUXE System panel connector
•
System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED
cable to this connector. The system power LED lights up when you turn on the system
power, and blinks when the system is in sleep mode.
•
Hard disk drive activity LED (2-pin +HDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable
to this connector. The IDE LED lights up or flashes when data is read from or written to
the HDD.
•
•
Power/Soft-off button (2-pin PWRBTN)
This 2-pin connector is for the system power button.
Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without
turning off the system power.
7.
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch. Connect
one end of the chassis intrusion sensor or switch cable to this connector. The chassis
intrusion sensor or switch sends a high-level signal to this connector when a chassis
component is removed or replaced. The signal is then generated as a chassis intrusion
event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a jumper
cap. Remove the jumper caps only when you intend to use the chassis intrusion
detection feature.
CHASSIS
E45M1-I DELUXE Chassis intrusion connector
1-14
ASUS E45M1-I DELUXE
8.
USB 3.0 connector (20-1 pin USB3_34)
This connector is for the additional USB 3.0 ports. Connect the bundled USB 3.0
bracket cable to this connector, then install the USB 3.0 bracket to the rear side of the
chassis. If your chassis support customised front panel installation, with ASUS USB 3.0
header, you can have a front panel USB 3.0 solution.
E45M1-I DELUXE USB3.0 front panel connector
9.
USB 2.0 connectors (10-1 pin USB56, USB78)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of
these connectors, then install the module to a slot opening at the back of the system
chassis. These USB connectors comply with USB 2.0 specification that supports up to
480 Mbps connection speed.
USB78
USB56
E45M1-I DELUXE USB2.0 connectors
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
The USB module cable is purchased separately.
Chapter 1: Product introduction
1-15
|