VB172 Series
LCD Monitor
User Guide
Table of contents
Notices.......................................................................................................... iv
Safety.information........................................................................................ v
Care.&.Cleaning........................................................................................... vi
Chapter.1:.
Product.introduction.
1.1.
1.2.
1.3.
Welcome!....................................................................................... 1-1
Package.contents.......................................................................... 1-1
Monitor.introduction..................................................................... 1-2
1.3.1
1.3.2
Front of the LCD monitor ................................................ 1-2
Rear of the LCD monitor ................................................ 1-3
Chapter.2:.
Setup
2.1.
2.2.
2.3.
2.4.
2.5.
Assembling.the.monitor.base...................................................... 2-1
Adjusting.the.monitor................................................................... 2-1
Detaching.the.arm/base.(for.VESA.wall.mount)......................... 2-2
Connecting.the.cables.................................................................. 2-3
Turning.on.the.monitor................................................................. 2-3
Chapter.3:.
General.Instruction..
3.1.
OSD.(On-Screen.Display).menu.................................................. 3-1
3.1.1
How to reconfigure.......................................................... 3-1
3.1.2
OSD Function Introduction.............................................. 3-1
3.2.
3.3.
3.4.
Specifications summary............................................................... 3-4
Troubleshooting.(FAQ)................................................................. 3-5
Supported.operating.modes........................................................ 3-6
iii
Notices
Federal.Communications.Commission.Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’
s instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
As an Energy Star® Partner, our company has determined that this product meets
the Energy Star® guidelines for energy efficiency.
Canadian.Department.of.Communications.Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
•
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
Use the appropriate power plug which complies with your local power standard.
•
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed computers
which have appropriate configured receptacles marked between 100-240V AC.
If you encounter technical problems with the monitor, contact a qualified service
technician or your retailer.
v
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the LCD. Never spray cleaner directly on the screen, as it may drip
inside the monitor and cause an electric shock.
The.following.symptoms.are.normal.with.the.monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
•
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions.used.in.this.guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.. ASUS.websites
The ASUS websites worldwide provide updated information on ASUS
2.. Optional.documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
vii
viii
1.1
Welcome!
Thank you for purchasing the ASUS® VB172 Series LCD monitor!
The latest LCD monitor from ASUS provides a host of features that enhance your
viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the VB172 Series brings you!
1.2
Package contents
Check your VB172 Series LCD monitor package for the following items:
LCD monitor
Monitor base
User manual CD
Quick Start Guide
1 x Power cord
1 x VGA cable
1 x DVI cable (Only for VB172T)
1 x Audio cable (Only for VB172T, VB172S, and VB172F))
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS LCD Monitor VB172 Series
1-1
1.3
Monitor introduction
1.3.1.
Front.of.the.LCD.monitor
6
4
5
1
2
3
1.
Button:
•
Use this hotkey to switch from five video preset modes (Game
Mode, Night View Mode, Scenery Mode, Standard Mode, Theater Mode)
with SPLENDID™ Video Enhancement Technology.
•
Exit the OSD menu or go back to the previous menu as the OSD menu
is active.
•
Automatically adjust the image to its optimized position, clock, and phase
by pressing this button for 2-4 seconds (for VGA mode only).
2.
Button:
•
Press this button to decrease the value of the function selected or move
left/up to the previous function.
•
This is also a hotkey for Volume adjustment.
3.
MENU Button:
•
Press this button to enter/select the icon (function) highlighted while the
OSD is activated.
4.
Button:
•
•
Press this button to increase the value of the function selected or move
right/down to the next fuction.
This is also a hotkey for Brightness adjustment.
1-2
Chapter 1: Product introduction
5.
6.
Power button
•
Press this button to turn the monitor on/off.
Power indicator
The color definition of the power indicator is as the below table.
•
Status
Blue
Description
ON
Amber
OFF
Standby mode
OFF
1.3.2.
Rear.of.the.LCD.monitor.
Screw.holes.for.
VESA.Wall.Mount
Rear.connectors
3
4
1
2
Rear.connectors
1.
2.
AC-IN.port. This port connects the power connector from the bundled power
cord.
DVI.port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
3.
VGA.port. This 15-pin port is for PC VGA connection.
4.
Audio-in.port. This port connects PC audio source by the bundled audio
cable.
ASUS LCD Monitor VB172 Series
1-3
1-4
Chapter 1: Product introduction
2.1
Assembling the monitor base
To assemble the monitor base:
1.
2.
Have the front of the monitor face down on a table.
Connect the base with the arm according to the below drawing. A click shows
that the base has been connected successfully.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
You can adjust the monitor’s angle from -5º to 20º.
-5º~20º
It is normal that the monitor slightly shakes while you adjust the the viewing
angle.
ASUS LCD Monitor VB172 Series
2-1
2.3
Detaching the arm/base
(for VESA wall mount)
The detachable arm/base of the VB172 Series LCD monitor is specially designed
for VESA wall mount.
To detach the arm/base:
1.
2.
3.
Have the front of the monitor face down on a table.
Remove the rubbers in the four screw holes (Figure 1).
Use a screwdriver to remove the four screws on the arm (Figure 1), then slide
out the arm/base to detach it from the monitor (Figure 2).
Rubbers.in.the.
screw.holes.
Four.screws.
Arm/base
Figure.2
Figure.1
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2-2
Chapter 2: Setup
2.4
Connecting the cables
1.
Connect the cables as the following instructions:
•
•
•
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer's audio-out port.
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input port, the other end to a power outlet.
To connect the VGA/DVI cable:
a. Plug the VGA/DVI connector to the LCD monitor’s VGA/DVI port.
b. Connect the other end of the VGA/ DVI cable to your computer’s VGA/
DVI port.
c. Tighten the two screws to secure the VGA/DVI connector.
When both the VGA and the DVI cables are connected, you can choose either
VGA mode or DVI mode from the Input Select item of the OSD functions.
2.
Gather all the cables by putting them through the cable hole.
Cable hole
2.5
Turning on the monitor
Gently press the power button
button. The power indicator
. See page 1-2 for the location of the power
lights up in blue to show that the monitor is ON.
ASUS LCD Monitor VB172 Series
2-ꢀ
2-4
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate
the OSD menu.
2.
Press
the desired function by pressing the MENU button. If the function selected
has a sub-menu, press and again to navigate through the sub-menu
and
to navigate through the functions. Highlight and activate
functions. Highlight and activate the desired sub-menu function by pressing
the MENU button.
3.
Press
and
to change the settings of the selected function.
4.
To exit the OSD menu, press the
button. Repeat step 2 and step 3 to
adjust any other function.
3.1.2.
OSD.Function.Introduction
1.. Spendid
This function contains five
sub-functions you can select
for your preference. Each mode has the
Reset selection, allowing you to maintain
your setting or return to the preset mode.
•
•
•
•
•
Scenery.Mode: best choice for scenery photo display with SPLENDID™
Video Enhancement.
Standard.Mode: best choice for document editing with SPLENDID™
Video Enhancement.
Theater.Mode: best choice for movie with SPLENDID™ Video
Enhancement.
Game.Mode: best choice for game playing with SPLENDID™ Video
Enhancement.
Night.View.Mode: best choice for dark-scene game or movie with
SPLENDID™ Video Enhancement.
•
•
In the Standard Mode, the Satuation and Sharpness functions are not
user-configurable.
In the other modes, the sRGB function is not user-configurable.
ASUS LCD Monitor VB172 Series
3-1
2.. Image.
You can adjust brightness, contrast,
sharpness, saturation,position (VGA
only), ASCR, and focus (VGA only) from
this main function.
•
Brightness: the adjusting range is from 0 to 100.
activate this function.
is a hotkey to
•
•
•
•
•
Contrast: the adjusting range is from 0 to 100.
Sharpness: the adjusting range is from 0 to 100.
Saturation: the adjusting range is from 0 to 100.
ASCR: turns on/off the ASCR(ASUS Smart Contrast Ratio) function.
Position: adjusts the horizontal postition (H-Position) and the vertical
position (V-Position) of the image. The adjusting range is from 0 to 100.
Focus: reduces Horizonal-line noise and Vertical-line noise of the image
by adjusting (Phase) and (Clock) separately. The adjusting range is from
0 to 100.
•
•
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
3.. Color..
Select the image color you like
from this function.
•
•
Color Temp.: contains five color modes including Cool, Normal,
Warm, sRGB, and User mode.
Skin Tone: contains three color modes including Reddish, Natural,
and Yellowish.
In the User mode, colors of R (Red), G (Green), and B (Bluee) are user-
configurable; the adjusting range is from 0-100.
3-2
Chapter 3: General Instruction
4.. Input.Select.
In this function, you can select
either VGA or DVI input source.
(Only for some models)
5.. System.Setup.
Allow you to adjust the system.
•
Volume: the adjusting range is from 0 to 100.
this function.
is a hotkey to activate
•
OSD Setup: adjusts the horizontal postition (H-Position) and
the vertical position (V-Position) of the OSD. The adjusting range is
from 0 to 100. In the OSD Timeout selection, you can adjust the
OSD timeout from 10 to 120.
•
Language: there are ten languages for your selection,
including English, German, Italian, French, Dutch, Spanish, Russian,
Traditional Chinese, Simplified Chinese, Japanese, and Korean.
•
•
Information: shows the monitor information.
Reset: “Yes” allows you to restore the default setting.
ASUS LCD Monitor VB172 Series
3-3
3.2
Specifications summary
Panel.Type
Panel.size
TFT LCD
17" wide screen
Max...Resolution
SXGA+ 1280 x 1024
Brightness.(Typ.)
Contrast.Ratio.(Typ.)
Viewing angle(H/V) CR ≥ 10
Display.colors
300 cd/m2 ; 250 cd/m2 (VB172F only)
700:1 / 1000:1 (VB172F only)
160º/160º; 170º/160º (VB172F only)
16.2M
Response.time
5ms (Tr+Tf) / 2sms (GtG) (VB172F only)
Yes
SPLENDID™.Video.
Enhancement
SPLENDID™.selection
Auto.adjustment
5 video preset modes (by hotkey)
Yes (by hotkey)
Color.temperature.selection 5 color temperatures
Skin-Tone.selection
Digital.input
Analog.input
Audio-in.port
Colors
3 skin-tones
DVI-D (VB172T only)
D-Sub
3.5 mm Mini-jack (VB172T, VB172S, VB172F only)
Black
Speaker.(Built-in)
Power.LED
1W x 2 Stereo (VB172T, VB172S, VB172F only)
Blue (On)/ Amber (Standby)
VESA.wall.mount
Tilt
100 mmx 100 mm (purchased separately)
+20º~-5º
Yes
Kensington.lock
Voltage.rating
AC: 100~240V
*Specifications are subject to change without notice.
3-4
Chapter 3: General Instruction
3.3
Troubleshooting (FAQ)
Problem
Possible.Solution
Power LED is not ON
• Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
The power LED lights amber and there is no • Check if the monitor and the computer are
screen image
in the ON mode.
• Make sure the signal cable is properly
connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings
via OSD.
Screen image is not centered or sized
• Press the
button for two seconds to
properly
automatically adjust the image.
• Adjust the H-Position or V-Position settings
via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure that
not look white)
none of the pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the
Color Temperature via OSD.
Screen image is blurry or fuzzy
• Press the
button for two seconds to
automatically adjust the image (for VGA
mode only).
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
• Ensure that the audio cable is properly
connected to the monitor and the computer
• Adjust the volume settings of both your
monitor and computer.
• Ensure that the computer sound card driver
is properly installed and activated.
ASUS LCD Monitor VB172 Series
3-5
3.4
Supported operating modes
Display.resolution
Horizontal.frequency
Refersh.rate
640 x 350
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
720 x 400
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 870
1280 x 1024
1280 x 1024
31.5KHz
31.5KHz
31.5KHz
35.0KHz
37.9KHz
37.5KHz
31.5KHz
35.1KHz
37.9KHz
46.7KHz
48.1KHz
49.7KHz
48.4KHz
56.5KHz
60.0KHz
67.5KHz
68.7KHz
64KHz
70Hz
70Hz
60Hz
67Hz
72Hz
75Hz
70Hz
56Hz
60Hz
75Hz
72Hz
75Hz
60Hz
70Hz
75Hz
75Hz
75Hz
60Hz
75Hz
80KHz
*.Modes.not.listed.in.the.table.may.not.be.supported..For.optimal.resolution,.we.recommend.that..
...you.choose.a.mode.listed.in.the.table.above.
3-6
Chapter 3: General Instruction
|