VK248
LCD Monitor
User Guide
MENU
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that
this product meets the Energy Star® guidelines for energy
efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouiller du Canada.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
•
Use the appropriate power plug which complies with your local power standard.
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
v
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
information in different region.
vii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power cord
VGA cable
DVI cable
USB cable
Audio cable
LifeFrame 2 CD
If any of the above items is damaged or missing, contact your retailer
immediately.
1.3
LifeFrame 2 software
ASUS VK248 provides the easy-to-use LifeFrame 2 software that can work with
the webcam, allowing users to create their own photos or video clips.
Installation instructions
•
LifeFrame 2 only supports Microsoft® Windows® 7/ Vista / XP Service
Pack 2 (3) operating systems.
•
The LifeFrame 2 software is bundled in the support CD.
1. Close all other applications.
2. Insert the support CD into the optical drive and run the LifeFrame 2 program.
3. Follow the on-screen instructions to complete the installation.
ASUS VK248 LCD Monitor
1-1
1.4
Monitor introduction
1.4.1
Front view
HD Webcam
MENU
1
2
3
4
5
6
1.
button:
Selects a desired preset mode.
•
•
Exits the OSD menu or goes back to the previous menu when the OSD
menu is active.
•
Automatically adjusts the image to its optimized position, clock, and phase
by pressing this button for 2-4 seconds (for VGA mode only).
2.
•
Decreases values or moves your selection left/down.
•
Activates the QuickFit function.(Please refer to 1.4.3 QuickFit Function).
3.
4.
MENU button:
•
Turns on the OSD menu. Enacts the selected OSD menu item.
•
•
Increases values or moves your selection right/up.
Brightness hotkey
1-2
Chapter 1: Product introduction
5.
6.
button:
Press
(Input Select button) to display HDMI signals after you connect
HDMI cable with the monitor.
•
Selects an available input source.
Power button/power indicator
•
•
Turns the monitor on/off.
The color definition of the power indicator is as the below table.
Status
Description
Blue
ON
Amber
OFF
Standby mode
OFF
1.4.2
Back view
4
6
7
Rear connectors
1.
2.
AC-IN port. This port connects the power cord.
Audio-in port. This port connects PC audio source by the bundled audio
cable.
3.
4.
Earphone jack. This port is only available when an HDMI cable is
connected.
USB upstream port. This port is for connection with a USB upstream cable.
The cable enables the built-in webcam on the monitor.
5.
6.
HDMI port. This port is for connection with an HDMI compatible device.
DVI port. This 24-pin port is for PC (Personal Computer) DVI-D digital signal
connection.
7.
VGA port. This 15-pin port is for PC VGA connection.
ASUS VK248 LCD Monitor
1-3
1.4.3
QuickFit Function
The QuickFit function allows users have a preview of the document or photo layout
directly on screen without printing test copies.
To activate Quickfit, press the Quickfit hotkey, and then press the MENU key to
switch between different pattern sizes.
Alignment Grid
Letter
Photo 4x6, 3x5, 2x2
Photo 8x10, 5x7
When QuickFit is activated, press the control buttons on the front panel to make
adjustments. The QuickFit QSD displayed in the lower right corner of the screen
will guide users to make selections.
The QuickFit OSD shown on the screen is not accessible by tapping on it.
1-4
Chapter 1: Product introduction
ASUS VK248 LCD Monitor
1-5
1-6
Chapter 1: Product introduction
2.1
Assembling the monitor arm/base
To assemble the monitor base:
1.
2.
Have the front of the monitor face down on a table.
Attach the base with the arm until it clicks into place.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
Hold the stand to prevent the monitor from falling when you change its angle.
+20˚ to -5˚
The recommended adjusting angle is
.
。
。
-5 to +20
It is normal that the monitor slightly shakes while you adjust the viewing angle.
ASUS VK248 LCD Monitor
2-1
2.3
Detaching the arm/base (for VESA
wall mount)
The detachable arm/base of this monitor is specially designed for VESA wall
mount.
To detach the arm/base:
1.
2.
3.
Have the front of the monitor face down on a table.
Remove the rubbers in the four screw holes. (Figure 1)
Use a screwdriver to remove the two screws on the arm (Figure 2), then slide
out the arm/base to detach it from the monitor (Figure 2).
Figure 1
Figure 2
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2-2
Chapter 2: Setup
2.4
Connecting the cables
1.
Connect the cables as the following instructions:
Audio-in
Earphone jack
USB 2.0
HDMI
DVI
VGA
•
•
•
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port.
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input, the other end to a power outlet.
To connect the VGA/DVI/HDMI cable:
a. Plug one end of the VGA/DVI/HDMI cable to the monitor’s VGA/DVI/
HDMI port.
b. Connect the other end of the VGA/DVI/HDMI cable to your computer's
VGA/DVI/HDMI port.
c. Tighten the two screws to secure the VGA/DVI connector.
•
•
To use the webcam: connect the upstream port of the monitor and the USB
port of your computer with the supplied USB cable.
To use the earphone (only when an HDMI cable is connected): connect the
end with plug type to the monitor’s earphone jack.
When these cables are connected, you can choose the desired signal from the
Input Select item in the OSD menu.
ASUS VK248 LCD Monitor
2-3
2.
Gather all the cables with the cable management slot.
cable management slot
2.5
Turning on the monitor
Press the power button
. See page 1-2 for the location of the power button. The
power indicator lights up in blue to show that the monitor is ON.
2-4
Chapter 2: Setup
ASUS VK248 LCD Monitor
2-5
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate
the OSD menu.
2.
Press
, and
to
navigate through the functions.
Highlight the desired function and
press the MENU button to activate
it. If the function selected has a sub-menu, press
and
again
to navigate through the sub-menu functions. Highlight the desired sub-menu
function and press the MENU button to activate it.
3.
4.
Press
To exit and save the OSD menu, press the
OSD menu disappears. To adjust other functions, repeat steps 1-3.
, and
to change the settings of the selected function.
button repeatedly until the
3.1.2
OSD function introduction
1.
Splendid
This function contains six sub-
functions you can select for your
preference. Each mode has the
Reset selection allowing you to
maintain your setting or return to
the preset mode.
•
•
Scenery Mode: best choice for scenery photo display with SPLENDID™
Video Enhancement.
Standard Mode: best choice for document editing with SPLENDID™
Video Enhancement.
•
•
•
Theater Mode: best choice for movies with SPLENDID™ Video
Enhancement.
Game Mode: best choice for games playing with SPLENDID™ Video
Enhancement.
Night View Mode: best choice for dark-scene games or movies with
SPLENDID™ Video Enhancement.
•
sRGB: best choice for viewing photos and graphics from PCs.
In the Standard Mode, the ASCR, Saturation and Sharpness functions are
not user-configurable.
ASUS VK248 LCD Monitor
3-1
2.
Color
You can adjust Brightness, Contrast,
Saturation, Color Temp., and Skin
Tone from this menu.
•
Brightness: the adjusting
range is from 0 to 100.
is a hotkey to activate this
function.
•
•
•
Contrast: the adjusting range is from 0 to 100.
Saturation: the adjusting range is from 0 to 100.
Color Temp.: contains four modes including Cool, Normal, Warm, and
User Mode.
•
•
Skin Tone: contains three color modes including Reddish, Natural, and
Yellowish.
Smart View: provides better display quality under big viewing angle.
In the User mode, colors of R (Red), G (Green), and B (Blue) are user-
configurable; the adjusting range is from 0-100.
3.
Image
You can adjust Sharpness, Trace
Free, Aspect Control, ASCR,
Position (VGA only), and Focus
(VGA only) from this menu.
Sharpness: the adjusting
•
•
•
range is from 0 to 100.
Trace Free: adjusts the
response time of the monitor.
Aspect Control: adjusts the aspect ratio to “Full”, “4:3”, or “OverScan”
(only available for the HDMI input).
•
•
ASCR: turns on/off the ASCR (ASUS Smart Contrast Ratio) function.
Position: adjusts the horizontal position (H-Position) and the vertical
position (V-Position) of the image. The adjusting range is from 0 to 100.
Focus: reduces Horizonal-line noise and Vertical-line noise of the image
by adjusting (Phase) and (Clock) separately. The adjusting range is from
0 to 100.
•
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
3-2
Chapter 3: General Instructions
4.
5.
Input Select
In this function, you can select your
desired input source.
System Setup
Allows you to adjust the system.
•
Splendid Demo Mode:
splits the screen into two for
Splendid modes comparison.
•
•
•
Volume: the adjusting range is from 0 to 100.
ECO Mode: reduces power consumption.
OSD Setup:
*
Adjusts the horizontal position (H-Position)/the vertical position
(V-Position) of the OSD from 0 to 100.
*
*
*
Adjusts the OSD timeout from 10 to 120 seconds.
Enables or disables the DDC/CI function.
Adjusts the OSD background from opaque to transparent.
•
•
Information: shows the monitor information.
Language: there are 10 languages for your selection, including English,
German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese,
Simplified Chinese, and Japanese.
•
All Reset: “Yes” allows you to restore the default settings.
ASUS VK248 LCD Monitor
3-3
3.2
Specifications summary (VK248)
Panel Type
Panel size
TFT LCD
24" (16:9, 61 cm) wide screen
Max. Resolution
Pixel pitch
1920 x 1080
0.2765 mm
250 cd/m2
Brightness (Typ.)
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
1000:1
50,000,000:1 (with ASCR on)
170˚/160˚
16.7 M
Response time
SPLENDID™ Video
Enhancement
2 ms (Gray to Gray)
Yes
SPLENDID™ selection
Auto adjustment
6 video preset modes (by hotkey)
Yes (by hotkey)
Color temperature selection 4 color temperatures
Skin-Tone selection
Digital input
Analog input
Audio-in port
Earphone jack
Colors
3 skin-tones
DVI-D with HDCP, HDMI v1.3
D-Sub
3.5 mm Mini-jack
Yes (only for HDMI)
Black
Speaker (Built-in)
Power LED
Tilt
2 W x 2 Stereo, RMS
Blue (On)/Amber (Standby)
+20˚~ -5˚
VESA wall mount
Kensington lock
Voltage rating
Power consumption
100 x 100 mm
Yes
AC: 100~240V
Power On: < 42 W, Standby: < 0.5 W,
Power Off: < 0.5 W
Temperature (Operating)
0˚C~40˚C
Temperature
-20˚C~+60˚C
(Non-operating)
Dimensions (W x H x D)
569.4 mm x 408.2 mm x 201 mm (machine)
641 mm x 473 mm x 161 mm (package)
Weight (Esti.)
5.0 kg (Net); 7.4 kg (Gross)
Multi-languages
10 languages (English, German, Italian, French, Dutch,
Spanish, Russian, Traditional Chinese, Simplified
Chinese, Japanese)
Accessories
VGA cable, DVI cable, USB cable, audio cable, power
cord, Quick start guide, warranty card, LifeFrame 2 CD
Regulation approvals
Energy Star®, CB, CE, Gost-R, CCC, UL/cUL, FCC,
C-Tick, BSMI, VCCI, RoHS, WEEE, J-MOSS, PSB, ErP,
Windows 7 WHQL
*Specifications are subject to change without notice.
3-4
Chapter 3: General Instructions
3.3
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
•
•
Press the
is in the ON mode.
Check if the power cord is properly
connected to the monitor and the power
outlet.
button to check if the monitor
The power LED lights amber and there is
no screen image
•
•
•
•
Check if the monitor and the computer are
in the ON mode.
Make sure the signal cable is properly
connected the monitor and the computer.
Inspect the signal cable and make sure
none of the pins are bent.
Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
•
•
Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
Press the
button for 2-4 seconds
to automatically adjust the image (for VGA
mode only).
•
•
Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
Make sure the signal cable is properly
connected to the monitor and the
computer.
•
Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
Perform All Reset via OSD.
Adjust the R/G/B color settings or select
the Color Temperature via OSD.
•
•
Screen image is blurry or fuzzy
•
Press the
button for 2-4 seconds
to automatically adjust the image (for VGA
mode only).
•
•
Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
Ensure that the HDMI cable is properly
connected to the monitor and the
computer.
•
•
Adjust the volume settings of both your
monitor and HDMI device.
Ensure that the computer sound card
driver is properly installed and activated.
ASUS VK248 LCD Monitor
3-5
3.4
Supported operating modes
Resolution
Frequency
Horizontal
Frequency (KHz)
Vertical Frequency Pixel (MHz)
(Hz)
640x480
31.5
35.0
37.9
37.5
31.5
35.16
37.9
48.1
46.9
49.7
48.4
56.5
60.0
67.5
45
60
67
72
75
70
56
60
72
75
75
60
70
75
75
60
60
60
60
60
75
60
60
60
60
60
25.18
30.24
31.50
31.50
28.32
36.00
40.00
66.75
49.50
57.28
65.00
75.00
78.50
108.00
75.25
79.50
83.50
108.00
108.00
135.00
85.50
85.50
106.50
162.00
146.25
640x480
640x480
640x480
720x400
800x600
800x600
800x600
800x600
832x624
1024x768
1024x768
1024x768
1152x864
1280x720
1280x768
1280x800
1280x960
1280x1024
1280x1024
1360x768
1366x768
1440x900
1600x1200
1680x1050
47.78
49.7
60.0
63.4
79.97
47.71
47.71
55.94
75.0
65.3
1920x1080
(Primary)
67.5
60
148.50
* Modes not listed in the table may not be supported. For optimal resolution, we recommend that
you choose a mode listed in the table above.
* This monitor supports full HD (480p, 576p, 720p, 1080i/p) video content from game consoles, DVD
players and other consumer video devices via HDMI.
3-6
Chapter 3: General Instructions
ASUS VK248 LCD Monitor
3-7
|