AP-64e EPROM WRITER
For Apple II, II+, IIe, III.
Hobby Model
THE BEST combination programmer
Features:
1. Eprom: 2716, 27.32, 2764.
2. Reliable
3. Easy to use (no external equipment needed)
4. Auto blank check.
5. Auto verify.
6. Error indicated.
7. voltage for program adjustable
8. Type selection by DIP switch
9. Fireware included
10. Write, Read, Copy, Compare. Blankcheck, Monitor functions
6. MONITOR: To enter the Apple machine language, you
can examine, change, move, compare and run
the contents of memory in machine language
of 6502 CPU.
User's guide: After you make installations of AP-64e EPROM WRITER
the following will be come to the screen:
A?—64 EPROM PROGRAMMER
ENHANCED VELCCM WRITTEN BY CARL
2)2716
4)2732
8)2764
?
Now you must key in the number 2,4 or 8 to choice how many
bytes you want to program your EPROMS. 2 represents 2K bytes (0000-07FF). 4
represents 4K bytes (C000-0FFF). 8 represents
8K bytes (0000-1FFF). Please reconfirm whether the DIP switch already set or not
before you key in any number, Errors could
be occurred in the following steps if you make wrong selection
When everything is right, you will see the next lines come to the screen:
1) WRITE
2) READ
3) COPY
4) COMPARE
5) BLANKCHECK
6) MONITOR
Before you make any action, the first thing is to learn how
to insert the EPROM into TEXTOOL:
1. To pull up the stick of textool that can release any ROM
or EPROM which already installed in place of textool.
2. To put the right EPROM into the textool. Because the textool
is 28 pins DIP socket that is for 2764 EPROMs, and 2716,2732
EPROMs are 24 pins, so the installation of 2716 and 2732 must
2 pins below calculated from the up side of textool. It is very
important to recheck the EPROM goes into the textool in right
pins, otherwise it might be caused a damage.
3. To push the stick of textool down to the PCB side. Now
the EPROM will be tightly held in the textool socket.
Now you may key in a number from 1 to 6 to choice any
function we mentioned before. Details are as follows:
1) WRITE: When you type”1”that means you will programing any
a block of memory content into EPROMs. The next line
come to the screen is:
START ADDRESS ?
just key in a start address of memory in hex code
and hit RETURN.
BLANK ? (Y/N)
A. If you went to “burn” a blank EPROM, now insert
the EPROM and type “Yes”, will test EPROM blank automatically.
ROM CHECK OK! (Means your eprom is ready to write)
SW ON
In case the EPROM has been programmed, Then
ROM CHECK ERR!! (Means your eprom can't write)
BLANK ? (Y/N)
Please change another one and do it again.
B. Sometimes you only want to correct data that already programmed in
EPROM, So please type “No”.
The blank check procedure will be omitted and
directly display:
SW ON
Now you just turn on the switch which is on the front
edge of AP-64e, and hit RETURN key. The writing function will start and address
hex code should be show on the
right down corner of the screen.
For 2716 it will take 95 seconds to fully programming,
When the “burning” is completed, the screen display:
COMPARE OK !!
SW OFF
Please turn the switch off and take the EPROM away
from the TEXTOOL, a new fully programming EPROM
has been produced. Or the screen displayed as:
COMPARE ERR !! SW OFF
that means your EPROM not be written. as you need,
please turn off the switch and change a new good
EPROM and do again until you get a fully programmed
EPROM.
2) READ: To instal the EPROM into the TEXTOOL and type 2,
the follows will come to the screen:
START ADDRESS ? $
Also please key in a start address of memory in hex
code. Where wish to reed in from EPROMs. and hit
RETURN. After one second, Read function finished:
READ
(Show on the screen)
1) WRITE
2) READ
3) COPY
4) COMPARE
5) BLANKCHECK
6) MONITOR
Now you may key in 4 or 6 to check what you READ
from EPROMs according the next procedures we will
explained later.
3) COPY: To key in “3” means you Want to burn a new copy
EPROM from a old master ROM. You will see the follows
from the screen:
SET EASTER ROM
Please do it carefully, and hit RETURN
READ
SET BLANK ROM
Please take the master ROM away and put a blank EPROM
in the textool, press RETURN:
BLANK ? (Y/N)
The next procedure is same as WRITE until you get a
new copy EPROM.
4) COMPARE: To compare a block of memory and the master EPROM.
Only to hit “4” for compare function, the following
come to the screen:
START ADDRESS ? $
Please key in start address of memory location in
where you want to compare with the master EPROM
which is inserted in the TEXTOOL. and hit RETURN
SET MASTER ROM
please do it, or you already have cone just hit RETURN, COMPARE OK!
or
COMPARE ERR!! CONTINUE ? (Y/N)
Just key in “Yes” for continue or “No” to Stop it.
If you want to compare two or more EPROMs, the first step is to read data from
eprom t.o the memory location of
your system as READ function and then set another eprom
as master rom and do COMPARE function.
BLANKCHECK: To test EPROMS is blank or riot. please key
in “5” and then you will see the follows on the screen:
SET BLANK ROM
5)
Please insert the EPROM you want to test and hit
RETURN:
ROM CHECK OK! (If the EPROM is blank.)
or
EPROM CHECK ERR!! (When the EPROM is not blank.)
MONITOR: To enter the Apple machine language when you
type “6”. You can examine, change, move, compare
and run the contents of memory in machine language.
Please refer the Apple reference manual for more
details.
6)
Problems and Solutions: After using AP-64e EPROM WRITER, you will find out so many
advantages such as faster, portable and
more reliable. But some problems will come to bother you too. Hereafter we like to point
out problems may be occurred and
show you how to settle.
1. The EPROMs can not be programmed: Since the EPROMs which
could be already stored program, you can't write any
more, except you erase and program again.
2. If you forget to key in ROM SIZE (represented by 2,4,8)
the errors could be occurred when you use WRITE, READ,
COPY functions, please reset your computer and
boot AP64e again.
3. Don’t forget to turn the switch off when you use AP-64e
from cold start or when screen indicate you “SW OFF”.
|