3-081-707-11(1)
CD/DVD
Player
Operating Instructions
For customers in the U.S.A
Owner’s Record
The model and serial numbers are located at the rear of the unit.
Record the serial number in the space provided below. Refer to them
whenever you call upon your Aiwa dealer regarding this product.
Model No. XD-AX10
Serial No.______________
For assistance and information
visit us on the internet at
call toll free 1-800-BUY-AIWA
For Customers in Canada
If this product is not working properly, please call 1-877-869-2492 for
Peace of Mind Warranty Replacement service.
For other product related questions please contact our Customer
Information Service Centre at 1-877-869-2492 or write to us at:
Customer Information Service 115 Gordon Baker Road, Toronto,
Ontario, M2H 3R6
XD-AX10
© 2003 Sony Corporation
For the model supplied with the AC plug
adaptor
If the AC plug of your unit does not fit into
the wall autlet, attach the supplied AC plug
adaptor.
Precautions
• The power requirements and power
consumption of this player are indicated on
the back of the player. Check that the
player’s operating voltage is identical with
your local power supply.
MODEL NO.
1
On operation
AC 00V 00Hz
NO.
Power requirements t
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
0-000-000-00
On safety
• Caution – The use of optical instruments
with this product will increase eye hazard.
• To prevent fire or shock hazard, do not
place objects filled with liquids, such as
vases, on the apparatus.
• Should any solid object or liquid fall into
the cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
On adjusting volume
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
On power sources
• The player is not disconnected from the AC
power source as long as it is connected to
the wall outlet, even if the player itself has
been turned off.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord, grasp the plug itself; never pull
the cord.
• Should the AC power cord need to be
changed, have it done at a qualified service
shop only.
On cleaning discs
Do not use a commercially available cleaning
disc. It may cause a malfunction.
On placement
IMPORTANT NOTICE
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug that might block the
ventilation holes.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
Display Panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems
concerning your player, please consult your
nearest Aiwa dealer.
3
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Welcome!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
This Player Can Play the Following Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes about the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Index to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Guide to On-Screen Displays (Control Bar). . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hookups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hooking Up the Player. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 2: Inserting Batteries into the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Step 3: Connecting the Video Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Step 5: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Step 6: Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Resuming Playback from the Point Where You Stopped the Disc
(Disc Resume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using the DVD’s Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Playing VIDEO CDs with PBC Functions (PBC Playback) . . . . . . . . . . . . . . 29
Playing an MP3 Audio Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Various Play Mode Functions (Program Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Searching for a Particular Point on a Disc (Scan, Slow-motion Play,
Search, Freeze Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Searching for a Title/Chapter/Track/Scene, etc. (Search mode) . . . . . . . . . . 37
Viewing Information About the Disc . . . . . . . . . . . . . . . . . . . . . . . 39
Checking the Playing Time and Remaining Time . . . . . . . . . . . . . . . . . . . . . 39
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Virtual Surround Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Enjoying Movies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Displaying the Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Adjusting the Playback Picture (PICTURE MODE) . . . . . . . . . . . . . . . . . . . . 44
Changing the Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4
Locking Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Limiting Playback by Children (PARENTAL CONTROL). . . . . . . . . . . . . . . . 46
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Using the Setup Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . . 50
Settings for the Display (SCREEN SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . 51
Custom Settings (CUSTOM SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Self-diagnosis Function (When letters/numbers appear in the display). . . . . 57
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Language Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5
About This Manual
This Player Can Play the
Following Discs
• Instructions in this manual describe the
controls on the remote. You can also use the
controls on the player if they have the same
or similar names as those on the remote.
• The meaning of the icons used in this
manual is described below:
Format of discs
DVD VIDEO
VIDEO CD
Music CD
Icon
Meaning
Functions available for DVD
VIDEOs and DVD-RWs/
DVD-Rs in video mode or
DVD+RWs/DVD+Rs
Functions available for VIDEO
CDs, Super VCDs, or CD-Rs/
CD-RWs in video CD format
or Super VCD format
The “DVD VIDEO” is a trademark.
Region code
Functions available for music
CDs or CD-Rs/CD-RWs in
music CD format
Your player has a region code printed on the
back of the unit and only will play DVD
VIDEO discs (playback only) labeled with
identical region codes. This system is used to
protect copyrights.
Functions available for DATA
CDs (CD-ROMs/CD-Rs/CD-
RWs containing MP3* audio
tracks)
ALL
* MP3 (MPEG 1 Audio Layer 3) is a standard
format defined by ISO/MPEG which compresses
audio data.
DVDs labeled
player.
will also play on this
If you try to play any other DVD, the message
“Playback prohibited by area limitations.”
will appear on the TV screen. Depending on
the DVD, no region code indication may be
labeled even though playing the DVD is
prohibited by area restrictions.
MODEL NO.
1
Region code
AC 00V 00Hz
NO.
0-000-000-00
6
• Music discs encoded with copyright protection
technologies
Example of discs that the player
cannot play
The player cannot play the following discs:
• All CD-ROMs (including PHOTO CDs)/
CD-Rs/CD-RWs other than those recorded
in the following formats:
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
– music CD format
– video CD format
– MP3 format that conforms to ISO9660*
Level 1/Level 2, or its extended format,
Joliet
Note on playback operations of
DVDs and VIDEO CDs
• Data part of CD-Extras
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
• DVD-RWs in VR mode
• DVD-ROMs
• DVD Audio discs
• HD layer on Super Audio CDs
• Super VCDs in PAL format
* A logical format of files and folders on CD-
ROMs, defined by ISO (International Standard
Organization).
Also, the player cannot play the following
discs:
Copyrights
• A DVD with a different region code.
• A disc recorded in a color system other than
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents, other
intellectual property rights owned by
Macrovision Corporation, and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation, and is intended for
home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or
disassembly is prohibited.
Notes
• Notes about DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs or CD-Rs/CD-RWs
Some DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs cannot be played
on this player due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. For more information, see the operating
instructions for the recording device. Note that
discs created in the Packet Write format cannot be
played.
7
Notes about the Discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it
in a car parked in direct sunlight as the
temperature may rise considerably inside
the car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the center out.
• Do not use solvents such as benzine,
thinner, commercially available cleaners, or
anti-static spray intended for vinyl LPs.
8
Index to Parts and Controls
For more information, refer to the pages indicated in parentheses.
Front panel
A [/1 (on/standy) button (25)
B Disc tray (25)
F x (stop) button (26)
G X (pause) button (26)
C Front panel display (10)
H H (play) button (25)
D
(remote sensor) (15)
I > (next) button (26, 36)
J . (previous) button (26, 36)
E A (open/close) button (25)
,continued
9
Front panel display
When playing back a DVD
Lights up when you can change the angle (45)
Playing status
Disc type
Current title/chapter or playing
time (40)
Lights up during
Repeat Play (34)
Current audio signal (41)
When playing back a VIDEO CD with Playback Control (PBC) (29)
Disc type
Playing status
Lights up during A-B Repeat Play
(34)
Current scene or playing time (40)
When playing back a CD, DATA CD (MP3 audio), or VIDEO CD (without PBC)
Lights up during
Repeat Play (35)
Playing status
Current track (40)
Playing time (40)
Lights up when playing MP3
audio tracks (30)
Disc type
10
Rear panel
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
P
B
PR
A DIGITAL OUT (COAXIAL) jack (20,
21, 22)
B LINE OUT L/R (AUDIO) jacks (19,
20, 21)
D S VIDEO OUT jack (16)
E COMPONENT VIDEO OUT jacks
(16)
C LINE OUT (VIDEO) jack (16)
,continued
11
Remote
A Z OPEN/CLOSE button (26)
B Number buttons (28)
The number 5 button has a tactile dot.*
C CLEAR button (32)
D SUBTITLE button (44)
E AUDIO button (41)
F ./> PREV/NEXT (previous/
next) buttons (26)
G
m/M
SCAN/SLOW
buttons (36)
H X PAUSE button (26)
I H PLAY button (25)
The H button has a tactile dot.*
J C/X/x/c buttons (28)
K DISPLAY button (13)
L TOP MENU button (28)
M [/1 (on/standby) button (25)
N TIME/TEXT button (39)
O PICTURE MODE button (44)
P ANGLE button (45)
Q SUR (surround) button (42)
R SEARCH MODE button (37)
S REPEAT button (34)
T
INSTANT SEARCH/STEP
button (26, 37)
INSTANT REPLAY/STEP
button (26, 37)
U
V x STOP button (26)
W ENTER button (23)
X O RETURN button (29)
Y MENU button (28, 30)
* Use the tactile dot as a reference when operating
the player.
12
◆Display 2
The following playback information is
displayed.
Example: When playing a DVD
Guide to On-Screen
Displays (Control Bar)
The following explains the Control Bar. The
Control Bar is used for making adjustments to
the settings or displaying information during
playback.
–
DVD T41
8
T 1:01:57
The displayed contents differ according to the
type of disc being played. The numbers in
parentheses indicate reference pages.
G TIME/TEXT icon
H Title number of the DVD (37)
I Chapter number of the DVD (37)
J Playing time or remaining time (39)
Displaying the Control Bar during
playback
The following displays appear when the
DISPLAY button is pressed repeatedly
during playback. You can select the setting
that suits the current playback item and view
the related information.
m
◆Display 3 (DVD playback only)
3 / 2 .1
DOLBY DIGITAL
◆Display 1
The following play modes 1~4 can be set.
A check mark is indicated when activated.
Example: When Repeat Play is selected. (The
display will differ when A-B Repeat Play is
set.)
K Format of the current audio signal (41)
m
◆No display
m
CHAPTER
◆Return to Display 1
A Repeat Play (34)
B Shuffle Play (33)
C Program Play (32)
D A-B Repeat Play (35)
E Unit being repeated in this example
F Playback status (N Playback,
X Pause, x Stop, etc.)
m
,continued
13
◆No display
Displaying the Control Bar in
stop mode
The following displays appear when the
DISPLAY button is repeatedly pressed
during stop mode. You can make basic
adjustments and customize the player to suit
your viewing preferences.
m
◆Return to Display 1
◆Display 1
The following settings can be made.
QUICK
A
SETUP (49)
• Select QUICK to make the minimum
number of basic adjustments for using the
player.
• Select CUSTOM to make a full range of
adjustments.
• Select RESET to return the SETUP
adjustments to the default settings.
B
PARENTAL CONTROL (46)
• Set this to limit the playback of selected
discs on this player.
m
◆Display 2
Shows the same information as Display 1
during playback.
CHAPTER
m
◆Display 3
Shows the same information as Display 2
during playback.
–
DVD T41
8
T 1:01:57
m
14
Hookups
Hooking Up the Player
Follow Steps 1 to 6 to hook up and adjust the settings of the player.
Notes
• Plug cords securely to prevent unwanted noise.
• Refer to the instructions supplied with the components to be connected.
• You cannot connect this player to a TV that does not have a video input jack.
• Be sure to disconnect the power of each component before connecting.
Step 1: Unpacking
Check that you have the following items:
• Audio/video cord (pinplug × 3 y pinplug × 3) (1)
• Remote commander (remote) (1)
• Size AA (R6) batteries (2)
• A plug adaptor is included with some models.
Step 2: Inserting Batteries into the Remote
You can control the player using the supplied remote. Insert two Size AA (R6) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
15
Step 3: Connecting the Video Cords
Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.
Select one of the patterns A through C, according to the input jack on your TV monitor,
projector, or AV amplifier (receiver).
A
C
INPUT
VIDEO
COMPONENT
VIDEO IN
Component
video cord
(not supplied)
(yellow)
Audio/video cord
(supplied)
Y
(green)
PB
PR
L
(blue)
(red)
AUDIO
R
TV, projector, or AV
amplifier (receiver)
TV, projector, or AV
amplifier (receiver)
(red)
(yellow)
to LINE OUT (VIDEO)
to COMPONENT
VIDEO OUT
(green)
(blue)
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
PB
PR
CD/DVD player
to S VIDEO OUT
INPUT
S VIDEO
B
TV, projector, or AV
amplifier (receiver)
S VIDEO cord (not supplied)
l : Signal flow
A If you are connecting to a video input jack
Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will
enjoy standard quality images.
Yellow (Video)
White (L)
Yellow (Video)
White (L)
Red (R)
Red (R)
Use the red and white plugs to connect to the audio input jacks (page 19). (Do this if you are
connecting to a TV only.)
16
B If you are connecting to an S VIDEO input jack
Connect the S VIDEO cord (not supplied). You will enjoy high quality images.
C If you are connecting to a monitor, projector, or AV amplifier (receiver)
having component video input jacks (Y, PB, PR)
Connect the component via the COMPONENT VIDEO OUT jacks using a component video
cord (not supplied) or three video cords (not supplied) of the same kind and length. You will
enjoy accurate color reproduction and high quality images.
Green
Blue
Green
Blue
Red
Red
When connecting to a wide screen TV
Depending on the disc, the image may not fit your TV screen. If you want to change the aspect
ratio, please refer to page 51.
Note
Connect the player directly to the TV. If you pass the player signals via the VCR, you may not receive a clear
image on the TV screen.
VCR
CD/DVD player
TV
Connect
directly
17
Step 4: Connecting the Audio Cords
Refer to the chart below to select the connection that best suits your system. Be sure to also read
the instructions for the components you wish to connect.
Select a connection
Select one of the following connections,
A
through
D
.
Components to be connected
Connection
(page 19)
Your setup (example)
TV
A
B
C
D
• Surround effects: Virtual Surround WIDE (page
42)
Stereo amplifier (receiver) and two speakers
or
MD deck/DAT deck
(page 20)
(page 21)
(page 22)
AV amplifier (receiver) having a Dolby*
Surround (Pro Logic) decoder and 3 to 6
speakers
• Surround effects: Dolby Surround (Pro Logic)
(page 58)
AV amplifier (receiver) with digital input jacks
having a Dolby Digital or DTS** decoder and 6
speakers
• Surround effects:
– Dolby Digital (5.1ch) (page 58)
– DTS (5.1ch) (page 58)
*
Manufactured under license from Dolby
Laboratories. “Dolby,” “Pro Logic,” and the
double-D symbol are trademarks of Dolby
Laboratories.
** “DTS” and “DTS Digital Out” are trademarks
of Digital Theater Systems, Inc.
18
A
Connecting to your TV
This connection will use your TV speakers for sound.
CD/DVD player
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
PB
PR
A
LINE OUT
TV
(yellow)*
(yellow)*
(white)
(white)
(red)
R-AUDIO-L
VIDEO
(red)
Audio/video
cord (supplied)
to LINE OUT L/R
(AUDIO)
to audio input
l : Signal flow
* The yellow plug is used for video signals (page
16).
z Hint
When connecting to a monaural TV, use a stereo-
mono conversion cord (not supplied). Connect the
LINE OUT L/R (AUDIO) jacks to the TV’s audio
input jack.
,continued
19
Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to
B
an MD deck or DAT deck
B-1
If the stereo amplifier (receiver) has audio input jacks L and R only, use
. If the amplifier
B-2
(receiver) has a digital input jack, or when connecting to an MD deck or DAT deck, use
.
In this case, you can also connect the player directly to the MD deck or DAT deck without using
your stereo amplifier (receiver).
CD/DVD player
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
PB
PR
B-2
B-1
Coaxial digital
cord (not supplied)
Stereo audio cord
(not supplied)
DIGITAL OUT
LINE OUT
(white)
(red)
PCM/DTS/
DOLBY DIGITAL
or
COAXIAL
R-AUDIO-L
VIDEO
to DIGITAL OUT
(COAXIAL)
to LINE OUT L/R (AUDIO)
(white)
(red)
to coaxial digital input
to audio input
[Speakers]
Front (L)
Stereo amplifier (receiver)
MD deck/DAT deck
Front (R)
l: Signal flow
20
C
Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro
Logic) decoder and 3 to 6 speakers
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or multi-
channel audio (Dolby Digital) discs.
C-1
If your amplifier (receiver) has L and R audio input jacks only, use
. If your amplifier
(receiver) has a digital input jack, use
.
C-2
CD/DVD player
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
PB
PR
C-2
C-1
Stereo
audio cord (not
supplied)
Coaxial digital cord
(not supplied)
DIGITAL OUT
LINE OUT
(white)
(red)
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
or
to DIGITAL OUT
(COAXIAL)
to LINE OUT L/R (AUDIO)
(white)
(red)
to coaxial digital input
to audio input
[Speakers]
[Speakers]
Front (L)
Amplifier (receiver) with Dolby
Surround decoder
Front (R)
Rear (L)
Rear (R)
Subwoofer
Center
Rear (mono)
l: Signal flow
Note
When connecting 6 speakers, replace the monaural
rear speaker with a center speaker, 2 rear speakers
and a subwoofer.
,continued
21
D
Connecting to an AV amplifier (receiver) with a digital input jack having
a Dolby Digital or DTS decoder and 6 speakers
This connection will allow you to use the Dolby Digital or DTS decoder function of your AV
amplifier (receiver).
CD/DVD player
DIGITAL OUT
LINE OUT
S
VIDEO
OUT
COMPONENT VIDEO OUT
PCM/DTS/
DOLBY DIGITAL
COAXIAL
R-AUDIO-L
VIDEO
Y
PB
PR
D
DIGITAL OUT
PCM/DTS/
DOLBY DIGITAL
COAIAL
to DIGITAL OUT
(COAXIAL)
Coaxial digital cord
(not supplied)
to coaxial digital input
[Speakers]
[Speakers]
AV amplifier (receiver) having
a decoder
Rear (L)
Center
Subwoofer
Front (L)
Rear (R)
l: Signal flow
Front (R)
Note
After you have completed the connection, be sure to
set “DOLBY DIGITAL” to “DOLBY DIGITAL”
and “DTS” to “ON” (page 23) in Quick Setup.
22
Step 5: Connecting the Power Cord
Plug the player and TV power cords into an AC outlet.
Step 6: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
MENU:
AUDIO:
SUBTITLE:
FRENCH
SPANISH
PORTUGUESE
5
6
Press X/x to select a language.
The player uses the language selected
here to display the menu and subtitles as
well.
ENTER
Press ENTER.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
1
2
3
Turn on the TV.
SCREEN SETUP
Press [/1.
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
TV TYPE:
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
BLACK LEVEL (COMPONENT OUT):
ON
“Press [ENTER] to run QUICK SETUP”
appears at the bottom of the screen. If this
message does not appear, select
“QUICK” under “SETUP” in the Control
Bar to run Quick Setup (page 50).
7
8
Press X/xto select the setting that
matches your TV type.
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 51)
4
Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 51)
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your amplifier
(receiver) appears.
,continued
23
“DTS” is selected.
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
DOLBY SURROUND
YES
LINE OUTPUT L/R (AUDIO)
ON
D-PCM
OFF
DIGITAL OUTPUT
NO
OFF
ON
9
Press X/xto select the type of jack
(if any) you are using to connect to
an amplifier (receiver), then press
ENTER.
12Press X/x to select whether or
not you wish to send a DTS signal
to your amplifier (receiver).
Choose the item that matches the audio
connection you selected on pages 19 to
Choose the item that matches the audio
connection you selected on pages 20 to
22 (
through
D
).
A
22 (
through
).
B
D
A
• If you connect just a TV and nothing
else, select “NO.” Quick Setup is
B-2
C-2
• OFF (page 54)
finished and connections are complete.
D
B-1
C-1
• ON (only if the amplifier (receiver) has
a DTS decoder) (page 54)
• Select “LINE OUTPUT L/R
(AUDIO).” Quick Setup is finished and
connections are complete.
13Press ENTER.
B-2
C-2
D
Quick Setup is finished. All connections
and setup operations are complete.
• Select “DIGITAL OUTPUT.” The Setup
Display for “DOLBY DIGITAL” appears.
Enjoying the surround sound
effects
To enjoy the surround sound effects of this
player or your amplifier (receiver), set the
following items as described below for the
audio connection you selected on pages 20 to
10Press X/x to select the type of
Dolby Digital signal you wish to
send to your amplifier (receiver).
Choose the signal that matches the audio
connection you selected on pages 20 to
22 (
B
through
D
).
22 (
through
). Each of these is the
B
D
default setting and does not need to be
adjusted when you first connect the player.
Refer to page 49 for using the Setup Display.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
DOLBY SURROUND
ON
D-PCM
Audio Connection (pages 19 to 22)
A
D-PCM
DOLBY DIGITAL
• No additional settings are needed.
C-1
B-1
B-2
C-2
• Set “DOWNMIX” to “DOLBY
SURROUND” (page 54)
• D-PCM (page 54)
• If the sound distorts even when the volume
is turned down, set “AUDIO ATT” to “ON”
(page 53)
D
• DOLBY DIGITAL (only if the
amplifier (receiver) has a Dolby Digital
decoder) (page 54)
B-2
C-2
D
• Set “DOWNMIX” to “DOLBY
SURROUND” (page 54)
• Set “DIGITAL OUT” to “ON” (page 54)
11Press ENTER.
24
4
5
Press Aon the player, and place a
disc on the disc tray.
Playing Discs
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
With the playback side facing down
Press H.
The disc tray closes, and the player starts
playback (continuous play). Adjust the
volume on the TV or the amplifier
(receiver).
Depending on the disc, a menu may
appear on the TV screen. For DVDs, see
page 28. For VIDEO CDs, see page 29.
To turn off the player
Press [/1. The player enters standby mode.
AUDIO
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn on this function, set “AUTO
POWER OFF” in “CUSTOM SETUP” to “ON”
(page 52).
Notes on playing DTS sound tracks on a CD
• When playing DTS-encoded CDs,
excessive noise will be heard from the
analog stereo jacks. To avoid possible
damage to the audio system, the consumer
should take proper precautions when the
analog stereo jacks of the player are
connected to an amplification system. To
enjoy DTS Digital Surround™ playback, an
external 5.1-channel decoder system must
be connected to the digital jack of the
player.
1
2
Turn on your TV.
Press [/1.
The player turns on.
3
Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
• Set the sound to “STEREO” using the
AUDIO button when you play DTS sound
tracks on a CD (page 41).
◆ When using an amplifier (receiver)
Turn on the amplifier (receiver) and
select the appropriate channel so that you
can hear sound from the player.
,continued
25
• Do not play DTS sound tracks without first
connecting the player to an audio
To
Operation
Stop play and remove Press Z
the disc
component having a built-in DTS decoder.
The player outputs the DTS signal via the
DIGITAL OUT (COAXIAL) jack even if
“DTS” in “AUDIO SETUP” is set to “OFF”
in the Setup Display (page 54), and may
affect your ears or cause your speakers to be
damaged.
Replay the previous
scene*
Press
INSTANT REPLAY
during playback
Briefly fast forward
the current scene**
Press
INSTANT SEARCH
during playback
Notes on playing DVDs with a DTS sound
track
• DTS audio signals are output only through
the DIGITAL OUT (COAXIAL) jack.
• When you play a DVD with DTS sound
tracks, set “DTS” to “ON” in “AUDIO
SETUP” (page 54).
• If you connect the player to audio
equipment without a DTS decoder, do not
set “DTS” to “ON” in “AUDIO SETUP”
(page 54). A loud noise may come out from
the speakers, affecting your ears or causing
the speakers to be damaged.
*
For DVD VIDEOs and DVD-RWs/DVD-Rs
only
** For DVD VIDEOs and DVD-RWs/DVD-Rs or
DVD+RWs only
zHints
• The Instant Replay function is useful when you
want to review a scene or dialog that you missed.
• The Instant Search function is useful when you
want to pass over a scene that you don’t want to
watch.
Note
You may not be able to use the Instant Replay or
Instant Search function with some scenes.
Additional operations
Locking the disc tray (Child
Lock)
You can lock the disc tray to prevent children
from opening it.
INSTANT REPLAY
INSTANT SEARCH
To
Operation
Press x
Stop
Pause
ENTER
Press X
RETURN
Resume play after
pause
Press X or H
When the player is in standby mode, press
O RETURN, ENTER, and [/1in this order
on the remote.
The player turns on and “LOCKED” appears
on the front panel display.
Go to the next chapter, Press >
track, or scene in
continuous play mode
Go back to the
Press .
The Zbutton on the player or the remote does
not work while the Child Lock is set.
previous chapter,
track, or scene in
continuous play mode
26
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
Resuming Playback from
the Point Where You
Stopped the Disc (Disc
Resume)
Note
Even if you select “RESET” under “SETUP” in the
Control Bar (page 50), the disc tray remains locked.
The player stores the point where you stopped
the disc for up to 6 discs and resumes
playback the next time you insert the same
disc. When you store a resume playback point
for the seventh disc, the resume playback
point for the first disc is deleted.
1 While playing a disc, press x to stop
playback.
“RESUME” appears on the front panel
display.
2 Press H.
The player starts playback from the point
where you stopped the disc in Step 1.
z Hints
• To play from the beginning of the disc, press x
twice, then press H.
• For CDs, and DATA CDs, the player remembers
the resume playback point for the current disc
unless the disc tray is opened, the power cord is
disconnected, or only for DATA CDs, the player
enters standby mode.
,continued
27
Notes
Using the DVD’s Menu
• “DISC RESUME” in “CUSTOM SETUP” must
be set to “ON” (default) for this function to work
(page 53).
• The resume playback point for the current disc is
cleared when:
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you want
using the TOP MENU button.
When you play DVDs that allow you to select
items such as the language for the subtitles
and the language for the sound, select these
items using the MENU button.
– you change the play mode.
– you change the settings on the Setup Display.
• This function may not work with some discs.
• Resume Play does not work during Shuffle Play
and Program Play.
• If “DISC RESUME” in “CUSTOM SETUP” is
set to “ON” and you play a recorded disc such as
DVD-RW, the player may play other recorded
discs from the same resume point. To play from
the beginning, press x twice and then press H.
Number
buttons
ENTER
TOP MENU
MENU
1
2
Press TOP MENU or MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
Press C/X/x/c or the number
buttons to select the item you want
to play or change.
If you press the number buttons, the
following display appears.
Press the number buttons to select the
item you want.
1
3
Press ENTER.
28
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
Playing VIDEO CDs with
PBCFunctions(PBCPlayback)
To return to PBC playback, press x twice then
press H.
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
Notes
• Depending on the VIDEO CD, “Press ENTER” in
step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case,
press H.
• The PBC functions of Super VCDs do not work
with this player. Super VCDs are played in
continuous play mode only.
Number
buttons
ENTER
RETURN
1
2
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
Select the item number you want
by pressing X/x or the number
buttons.
3
4
Press ENTER.
Follow the instructions in the
menu for interactive operations.
Refer to the instructions supplied with the
disc, as the operating procedure may
differ depending on the VIDEO CD.
To return to the menu
Press O RETURN.
29
(
)
1
3 0
Playing an MP3 Audio
Track
R O C K B E S T H I T
K A R A O K E
J A Z Z
R & B
M Y F A V O R I T E S O N G S
C L A S S I C A L
S A L S A O F C U B A
B O S S A N O V A
You can play back DATA CDs (CD-ROMs/
CD-Rs/CD-RWs) recorded in MP3 (MPEG1
Audio Layer 3) format.
2 Select an album using X/x and press
ENTER.
The list of tracks contained in the album
appears.
J A Z Z
(
)
1
9 0
0 1 S H E I S S P E C I A L
0 2 A L L Y O U N E E D I S . . .
0 3 S P I C Y L I F E
ENTER
0 4 H A P P Y H O U R
0 5 R I V E R S I D E
0 6
5
0 7 T A K E T I M E , T A K E T I M E
RETURN
MENU
3 Select a track using X/x and press
ENTER.
The selected track starts playing.
When a track or album is being played, its
title is shaded.
1
2
Press Z and place a DATA CD on
the disc tray.
To go to the next or previous page
Press c or C.
Press H.
The disc tray closes, and the player starts
to play the first MP3 audio track in the
first album on the disc.
To return to the previous display
Press O RETURN.
To turn off the display
Press MENU.
Notes
• This player can play MP3 audio tracks recorded in
the following sampling frequencies: 32 kHz, 44.1
kHz, 48 kHz.
• The playback order may be different from the
edited order. See “The Playback order of MP3
audio tracks” on the next page for details.
Notes
• Only the letters in the alphabet and numbers can
be used for album or track names. Anything else
is displayed as an “ * ”.
• ID3 tags cannot be displayed.
Selecting an album and track
About MP3 audio tracks
1 Press MENU.
You can play MP3 audio tracks on CD-ROMs
or CD-Rs/CD-RWs. However, the discs must
be recorded according to ISO9660 level 1,
level 2, or Joliet format for the player to
recognize the tracks.
The list of MP3 albums recorded on the
DATA CD appears.
You can also play discs recorded in Multi
Session.
30
See the instructions of the CD-R/CD-RW
device or recording software (not supplied)
for details on the recording format.
When you insert a DATA CD and press H,
the numbered tracks are played sequentially,
from 1 through 7. Any sub-albums/tracks
contained within a currently selected album
take priority over the next album in the same
tree. (Example: C contains D so 4 is played
before 5.)
When you press MENU and the list of MP3
albums appears (page 30), the albums are
arranged in the following order: A t B t
C t D t F t G. Albums that do not
contain tracks (such as album E) do not
appear in the list.
To play a Multi Session CD
This player can play Multi Session CDs when
an MP3 audio track is located in the first
session. Any subsequent MP3 audio tracks,
recorded in the later sessions, can also be
played back.
When audio tracks and images in music CD
format or video CD format are recorded in the
first session, only the first session will be
played back.
z Hints
• If you add numbers (01, 02, 03, etc.) to the front
of the track file names, the tracks will be played in
that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums of no more than two trees.
Notes
• If you put the extension “.MP3” to data not in
MP3 format, the player cannot recognize the data
properly and will generate a loud noise which
could damage your speaker system.
• The player cannot play audio tracks in MP3PRO
format.
Notes
• Depending on the software you use to create the
DATA CD, the playback order may differ from
the illustration above.
• The playback order above may not be applicable
if there are more than a total of 200 albums and
tracks in the DATA CD.
• The player can recognize up to 100 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks). The player
will not play any albums beyond the first 100
albums. Of the first 100 albums, the player will
play no more than a combined total of 200 albums
and tracks.
The Playback order of MP3 audio tracks
The playback order of albums and tracks
recorded on a DATA CD is as follows.
◆Structure of disc contents
Tree 1 Tree 2 Tree 3 Tree 4 Tree 5
ROOT
album
track
31
1 Press DISPLAY twice while the player
is in stop mode.
Various Play Mode
Functions (Program Play,
Shuffle Play, Repeat Play, A-B Repeat
Play)
The following Control Bar appears.
You can set the following play modes:
• Program Play (page 32)
• Shuffle Play (page 33)
• Repeat Play (page 34)
• A-B Repeat Play (page 35)
2 Press C/c to select
(PROGRAM), then press ENTER.
“TRACK” is displayed when you play
a VIDEO CD or CD.
PROGRAM
T
ALL CLEAR
Note
– –
1. TITLE
2. TITLE
3. TITLE
4. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
The play mode is canceled when:
– you open the disc tray.
– the player enters standby mode by pressing [/1.
5. TITLE
6. TITLE
7. TITLE
Creating your own program
(Program Play)
Titles or tracks
recorded on a disc
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own program. You can program up to 99
titles, chapters, and tracks.
3 Press c.
The cursor moves to the title or track row
“T” (in this case, “01”).
PROGRAM
T
C
ALL CLEAR
1. TITLE
– –
– –
01
02
03
04
05
ALL
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
06
Number
buttons
CLEAR
Chapters recorded on a disc
4 Select the title, chapter, or track you
want to program.
ENTER
◆ When playing a DVD
For example, select chapter “03” of title
“02.”
DISPLAY
Press X/x or the number buttons to select
“02” under “T,” then press ENTER.
PROGRAM
T
C
ALL CLEAR
– –
– –
ALL
1. TITLE
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
– –
– –
– –
– –
– –
– –
01
02
03
04
05
06
01
02
03
04
05
32
Next, press X/x or the number buttons to
select “03” under “C,” then press
ENTER.
3
Follow Step 4 for new programming. To
cancel a program, select “--” under “T,”
then press ENTER.
PROGRAM
To cancel all the titles, chapters, or tracks
in the programmed order
T
ALL CLEAR
1. TITLE 0 2 0 3
–
– –
– –
– –
– –
– –
– –
– –
2. TITLE
3. TITLE
4. TITLE
5. TITLE
6. TITLE
7. TITLE
01
02
03
04
05
1
Follow Steps 1 and 2 of “Creating your
own program (Program Play).”
2
3
Press X and select “ALL CLEAR.”
Press ENTER.
Selected title and chapter
z Hint
You can do Repeat Play or Shuffle Play of the
programmed titles, chapters, or tracks. During
Program Play, follow the steps of “Repeat Play”
(page 34) or “Shuffle Play” (page 33).
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x or the number buttons to select
“02” under “T,” then press ENTER.
Selected track
Notes
0:15:30
T
PROGRAM
• When playing Super VCDs, the total time of the
programmed tracks does not appear on the screen.
• You cannot use this function with VIDEO CDs
with PBC playback.
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
0 2
– –
– –
– –
– –
– –
– –
01
02
03
04
05
Playing in random order (Shuffle
Play)
Total time of the programmed tracks
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
5 To program other titles, chapters, or
tracks, repeat Steps 3 to 4.
The programmed titles, chapters, and
tracks are displayed in the selected order.
6 Press H to start Program Play.
Program Play begins.
When the program ends, you can restart
the same program again by pressing H.
CLEAR
To stop Program Play
Press CLEAR.
ENTER
To turn off the display
DISPLAY
Press DISPLAY repeatedly until the display
is turned off.
1 Press DISPLAY during playback.
To change or cancel a program
The following Control Bar appears.
1
Follow Steps 1 and 2 of “Creating your
own program (Program Play).”
2
Select the program number of the title,
chapter, or track you want to change or
cancel using X/x or the number buttons,
and press c.
,continued
33
2 Press C/c to select
(SHUFFLE),
then press ENTER repeatedly to select
the item to be shuffled.
Playing repeatedly (Repeat Play)
You can play all of the titles or tracks on a
disc or a single title, chapter, or track
repeatedly.
TITLE
You can use a combination of Shuffle or
Program Play modes.
◆ When playing a DVD
• TITLE
• CHAPTER
◆ When playing a VIDEO CD or CD
• TRACK
CLEAR
◆ When Program Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Program Play.
REPEAT
To return to normal play
Press CLEAR, or select “OFF” in Step 2.
To turn off the Control Bar
Press DISPLAY repeatedly until the Control
Bar is turned off.
1 Press REPEAT during playback.
The following display appears.
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
DISC
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
2 Press REPEAT repeatedly to select the
item to be repeated.
Note
You cannot use this function with VIDEO CDs with
PBC playback.
◆ When playing a DVD
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current
chapter.
◆ When playing a VIDEO CD or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
◆ When playing a DATA CD (MP3 audio)
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK: repeats the current track.
◆ When Program Play or Shuffle Play is
activated
• ON: repeats Program Play or Shuffle
Play.
34
To return to normal play
3 During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
Press CLEAR, or select “OFF” in Step 2.
z Hints
• You can set Repeat Play while the player is
stopped. After selecting the “REPEAT” option,
press H. Repeat Play starts.
–
A13
0:27:34 B
• You can also select “REPEAT” from the Control
Bar (page 13).
Note
4 When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
You cannot use this function with VIDEO CDs with
PBC playback.
Repeating a specific portion (A-
B Repeat Play)
You can play a specific portion of a title,
chapter or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
To return to normal play
Press CLEAR.
To turn off the Control Bar
Press DISPLAY repeatedly until the Control
Bar is turned off.
Note
When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Program Play are
canceled.
CLEAR
ENTER
DISPLAY
1 Press DISPLAY during playback.
The following Control Bar appears.
2 Press C/c to select
(A-B
REPEAT).
35
Playback direction
×2B t 1M t 2M t 3M
Searching for a Scene
3M (DVD/VIDEO CD only)
×2B (DVD/CD only)
Searching for a
Particular Point on a
Disc (Scan, Slow-motion Play,
Search, Freeze Frame)
Opposite direction
×2b t 1m t 2m t 3m
3m (DVD/VIDEO CD only)
×2b (DVD only)
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
The “×2B”/“×2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
Watching frame by frame (Slow-
motion play)
STEP
STEP
Press
m or M
when the player is
in pause mode. To return to the normal speed,
press H.
Each time you press
m or M
during Slow-motion play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
Playback direction
2
y 1
Opposite direction (DVD only)
2
y 1
The “2 y”/“2
than “1 y”/“1
” playback speed is slower
.”
Note
Depending on the DVD/VIDEO CD, you may not
be able to do some of the operations described.
To locate a point quickly using
the PREV (previous)/NEXT button
(Search)
You can search for a particular point on a disc
using . / > on the player.
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
During playback, press and hold > on the
player to locate a point in the playback
direction, or press and hold . to locate a
point in the opposite direction. When you find
the point you want, release the button to
return to normal playback speed.
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
playback speed changes. With each press the
indication changes as follows:
m or M
during scan, the
36
Playing one frame at a time
(Freeze Frame)
When the player is in the pause mode, press
STEP to go to the next frame. Press
STEP to go to the preceding frame
Searching for a Title/
Chapter/Track/Scene,
etc. (Search mode)
(DVD only). If you hold the button down, you
can view the frames in succession. To return
to normal playback, press H.
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD by track,
index, or scene. As titles and tracks are
assigned unique numbers on the disc, you can
select the desired one by entering its number.
Or, you can search for a scene using the time
code.
Number
buttons
CLEAR
SEARCH
MODE
ENTER
1
Press SEARCH MODE.
The following display appears.
“-- ( )” appears next to the icon (
refers to a number).
**
**
The number in parentheses indicates the
total number of titles, tracks, indexes,
scenes, etc. of the disc.
– –(
)
10
,continued
37
2
Press SEARCH MODE repeatedly
to select the search method.
Notes
• You cannot search for a scene on a DVD+RW
using the time code.
• The title, chapter, or track number displayed is the
same number recorded on the disc.
◆ When playing a DVD
TITLE
CHAPTER
TIME/TEXT
NUMBER INPUT
Select “TIME/TEXT” to search for a
starting point by inputting the time code.
◆ When playing a VIDEO CD without PBC
playback
TRACK
INDEX
◆ When playing a VIDEO CD with PBC
Playback
SCENE
INDEX
◆ When playing a CD
TRACK
INDEX
◆ When playing a DATA CD (MP3 audio)
ALBUM
TRACK
3
4
Select the number of the title,
track, scene, time code, etc. you
want by pressing the number
buttons to select the digit.
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, select “TIME/TEXT” in Step
2 and enter “2:10:20.”
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
Press ENTER.
The player starts playback from the
selected number.
z Hint
When the display is turned off, you can search for a
chapter (DVD) or track (CD) by pressing the
number buttons and ENTER.
38
◆ When playing a DVD
• T : : (hours: minutes: seconds)
Playing time of the current title
Viewing Information About the
Disc
* * *
• T– : :
* * *
Remaining time of the current title
Checking the Playing
Time and Remaining
Time
• C : :
* * *
Playing time of the current chapter
• C– : :
* * *
Remaining time of the current chapter
◆ When playing a VIDEO CD (with PBC
functions)
You can check the playing time and
remaining time of the current title, chapter, or
track. Also, you can check the DVD/CD text
or track name (MP3 audio) recorded on the
disc.
•
:
(minutes: seconds)
* *
Playing time of the current scene
◆ When playing a VIDEO CD (without
PBC functions) or CD
• T
:
(minutes: seconds)
* *
Playing time of the current track
• T– :
* *
Remaining time of the current track
• D
:
* *
TIME/TEXT
Playing time of the current disc
• D– :
* *
Remaining time of the current disc
◆ When playing a DATA CD (MP3 audio)
•
:
(minutes: seconds)
* *
Playing time of the current track
◆ When playing a Super VCD
• T (minutes: seconds)
Playing time of the current track
DISPLAY
:
* *
To check the DVD/CD text or track name
(MP3 audio)
Press TIME/TEXT repeatedly in Step 2 to
display text recorded on the DVD/CD/DATA
CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the
text. If the disc does not contain text, “NO
TEXT” appears.
For DATA CDs, only the track name of the
MP3 audio track appears.
1
2
Press TIME/TEXT during playback.
The following display appears.
T 1:01:57
Time
information
Press TIME/TEXT repeatedly to
change the time information.
The display and the kinds of time that you
can change depend on the disc you are
playing.
BRAHMS SYMPHONY
,continued
39
When playing a VIDEO CD (without PBC
functions) or CD
Checking the information on the
front panel display
You can view the time information and text
displayed on the TV screen also on the front
panel display. The information on the front
panel display changes as follows when you
change the time information on your TV
screen.
Playing time and number of the
current track
Remaining time of the current
track
When playing a DVD
Playing time of the disc
Remaining time of the disc
Text
Playing time of the current title
Remaining time of the current title
Playing time of the current chapter
Remaining time of the current
chapter
Current track and index number
(returns to top automatically)
z Hints
Text
• When playing VIDEO CDs with PBC functions,
the scene number or the playing time are
displayed.
• Long text that does not fit in a single line will
scroll across the front panel display.
• You can also check the time information and text
using the Control Bar (page 13).
Current title and chapter number
(returns to top automatically)
Notes
When playing a DATA CD (MP3 audio)
• Depending on the type of disc being played, the
DVD/CD text or track name may not be
displayed.
Playing time and number of the current track
• The player can only display the first level of the
DVD/CD text, such as the disc name or title.
• Playing time of MP3 audio tracks may not be
displayed correctly.
Track name
40
2
Press AUDIO repeatedly to select
the desired audio signal.
Sound Adjustments
◆ When playing a DVD
Depending on the DVD, the choice of
language varies.
Changing the Sound
When 4 digits are displayed, they
indicate a language code. Refer to
“Language Code List” on page 60 to see
which language the code represents.
When the same language is displayed two
or more times, the DVD is recorded in
multiple audio formats.
When playing a DVD recorded in multiple
audio formats (PCM, Dolby Digital, or DTS),
you can change the audio format. If the DVD
is recorded with multilingual tracks, you can
also change the language.
With CDs, DATA CDs, or VIDEO CDs, you
can select the sound from the right or left
channel and listen to the sound of the selected
channel through both the right and left
speakers. For example, when playing a disc
containing a song with the vocals on the right
channel and the instruments on the left
channel, you can hear the instruments from
both speakers by selecting the left channel.
◆ When playing a VIDEO CD, CD, or
DATA CD (MP3 audio)
The default setting is underlined.
• STEREO: The standard stereo sound
• 1/L: The sound of the left channel
(monaural)
• 2/R: The sound of the right channel
(monaural)
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: The stereo sound of the
audio track 1
• 1:1/L: The sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: The sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: The stereo sound of the
audio track 2
AUDIO
• 2:1/L: The sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: The sound of the right channel of
the audio track 2 (monaural)
DISPLAY
Checking the audio signal
format
If you press DISPLAY repeatedly during
playback, the format of the current audio
signal (Dolby Digital, DTS, PCM, etc.)
appears as shown below.
1
Press AUDIO during playback.
The following display appears.
The number in parentheses indicates the
total number of available audio signals.
( ):
1 4 ENGLISH
Example:
Dolby Digital 5.1 ch
Rear (L/R)
DOLBY DIGITAL
3 / 2 .1
Front (L/R)
+ Center
LFE (Low Frequency
Effect)
,continued
41
About audio signals
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
VirtualSurroundSettings
• Front (L)
• Front (R)
• Center
• Rear (L)
When you connect a stereo TV or 2 front
speakers, Virtual Surround lets you enjoy
surround sound effects by using sound
imaging to create virtual rear speakers from
the sound of the front speakers (L: left, R:
right) without using actual rear speakers.
If the player is set up to output the signal from
the DIGITAL OUT (COAXIAL) jack, the
surround effect will only be heard when
“DOLBY DIGITAL” is set to “D-PCM”
(page 54).
• Rear (R)
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
Notes
• If “DTS” is set to “OFF” in “AUDIO SETUP,”
the DTS track selection option will not appear on
the screen even if the disc contains DTS tracks
(page 54).
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or
“2:2/R.”
SUR
1
2
Press SUR during playback.
The following display appears.
WIDE
Press SUR repeatedly to select
one of the Virtual Surround
sounds.
Refer to the following explanations given
for each item.
• WIDE
• NIGHT
42
To cancel the setting
Select “OFF” in Step 2.
◆WIDE
Creates virtual rear speakers from the sound
of the front speakers (L, R) without using
actual rear speakers. The virtual speakers are
reproduced as shown in the illustration
below.
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
TV
: Virtual speaker
◆NIGHT
Large sounds, such as explosions, are
suppressed, but the quieter sounds are
unaffected. This feature is useful when you
want to hear the dialog and enjoy the
surround sound effects of “WIDE” at low
volume.
Notes
• When the playing signal does not contain a signal
for the rear speakers, the surround effects will be
difficult to hear.
• When you select one of theVirtual Surround
modes, turn off the surround setting of the
connected TV or amplifier (receiver).
• Make sure that your listening position is between
and at an equal distance from your speakers, and
that the speakers are located in similar
surroundings.
• Not all discs will respond to the “NIGHT”
function in the same way.
43
Adjusting the Playback
Picture (PICTURE MODE)
Enjoying Movies
Displaying the Subtitles
You can adjust the video signal of the DVD or
VIDEO CD from the player to obtain the
picture quality you want. Choose the setting
that best suits the program you are watching.
If subtitles are recorded on the discs, you can
change the subtitles or turn them on and off
whenever you want while playing a DVD.
PICTURE
MODE
SUBTITLE
1
2
Press SUBTITLE during playback.
The following display appears.
The number in parentheses indicates the
total number of available subtitles.
1
2
Press PICTURE MODE during
playback.
( )
1 8 :ENGLISH
The following display appears.
DYNAMIC
Press SUBTITLE repeatedly to
select the language.
Depending on the DVD, the choice of
language varies.
When 4 digits are displayed, they
indicate a language code. Refer to
“Language Code List” on page 60 to see
which language the code represents.
Press PICTURE MODE repeatedly
to select the setting you want.
The default setting is underlined.
• STANDARD: displays a standard
picture.
• DYNAMIC: produces a bold dynamic
picture by increasing the picture
contrast and the color intensity.
• CINEMA: enhances details in dark
areas by increasing the black level.
To turn off the subtitles
Select “OFF” in Step 2.
Note
Depending on the DVD, you may not be able to
change the subtitles even if multilingual subtitles
are recorded on it. You also may not be able to turn
them off.
z Hint
When you watch a movie, “CINEMA” is
recommended.
44
Changing the Angles
If various angles (multi-angles) for a scene
are recorded on the DVD, “ ” appears in the
front panel display. This means that you can
change the viewing angle.
ANGLE
1
2
Press ANGLE during playback.
The number of the angle appears on the
display.
The number in parentheses indicates the
total number of angles.
( )
2 7
Press ANGLE repeatedly to select
the angle number.
The scene changes to the selected angle.
Note
Depending on the DVD, you may not be able to
change the angles even if multi-angles are recorded
on the DVD.
45
2 Press X/x to select
(PARENTAL
CONTROL), then press ENTER.
The options for “PARENTAL
CONTROL” appear.
Locking Discs
Limiting Playback by
Children (PARENTAL CONTROL)
PLAYER
PLAYER
PASSWORD
The “PARENTAL CONTROL” function
allows you to set a playback limitation level.
Playback of some DVDs can be limited
according to a predetermined level such as the
age of the users. Scenes may be blocked or
replaced with different scenes.
3 Press X/x to select “PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
Number
buttons
PARENTAL CONTROL
Enter a new 4-digit password, then
ENTER
press
.
ENTER
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
DISPLAY
◆ When you have already registered a
password
The display for entering the password
appears.
1 Press DISPLAY while the player is in
stop mode.
The following Control Bar appears.
QUICK
PARENTAL CONTROL
Enter password, then press ENTER
.
46
4 Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
8 Select the level you want using X/x,
then press ENTER.
Parental Control setting is complete.
The display for setting the playback
limitation level appears.
PARENTAL CONTROL
LEVEL:
4: PG13
USA
STANDARD:
PARENTAL CONTROL
LEVEL:
OFF
USA
STANDARD:
The lower the value, the stricter the
limitation.
5 Press X/x to select “STANDARD,”
then press ENTER.
To turn off the Parental Control function
Set “LEVEL” to “OFF” in Step 8.
The selection items for “STANDARD”
are displayed.
To play a disc for which Parental Control is
set
PARENTAL CONTROL
LEVEL:
OFF
USA
USA
1
Insert the disc and press H.
The display for entering your password
appears.
STANDARD:
OTHERS
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
6 Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
z Hint
If you forget your password, remove the disc and
repeat Steps 1 to 3 of “Limiting Playback by
Children (PARENTAL CONTROL).” When you
are asked to enter your password, enter “199703”
using the number buttons, then press ENTER. The
display will ask you to enter a new 4-digit
password. After you enter a new 4-digit password,
replace the disc in the player and press H. When
the display for entering your password appears,
enter your new password.
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 48 using the number buttons.
7 Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
Notes
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
canceled, the level returns to the previous level.
PARENTAL CONTROL
LEVEL:
OFF
OFF
STANDARD:
8:
7: NC17
6:
5:
R
,continued
47
Area Code
If you make a mistake entering your
password
Press C before you press ENTER and input
the correct number.
Standard
Code
number
Standard
Code
number
Argentina
Australia
Austria
Belgium
Brazil
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
Korea
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
If you make a mistake
Malaysia
Mexico
Press O RETURN.
To turn off the display
Press DISPLAY repeatedly until the display
is turned off.
Netherlands
New Zealand
Norway
Canada
Chile
Pakistan
Philippines
Portugal
Russia
China
Denmark
Finland
France
Germany
India
Singapore
Spain
Sweden
Indonesia
Italy
Switzerland
Thailand
Japan
United
Kingdom
Changing the password
1 Press DISPLAY while the player is in
stop mode.
The Control Bar appears.
2 Press X/x to select
(PARENTAL
CONTROL), then press ENTER.
The options for “PARENTAL
CONTROL” appear.
3 Press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
4 Enter your 4-digit password using the
number buttons, then press ENTER.
5 Enter a new 4-digit password using the
number buttons, then press ENTER.
6 To confirm your password, re-enter it
using the number buttons, then press
ENTER.
48
3
4
Press X/x to select “CUSTOM,”
then press ENTER.
Settings and Adjustments
The Setup Display appears.
LANGUAGE SETUP
Using the Setup Display
OSD:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
MENU:
AUDIO:
SUBTITLE:
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things. For details on each Setup Display
item, see pages from 50 to 54.
Press X/x to select the setup item
from the displayed list:
Note
Playback settings stored in the disc take priority
over the Setup Display settings and not all the
functions described may work.
“LANGUAGE SETUP,” “SCREEN
SETUP,” “CUSTOM SETUP,” or
“AUDIO SETUP.” Then press
ENTER.
The Setup item is selected.
Example: “SCREEN SETUP”
Selected item
SCREEN SETUP
TV TYPE:
4:3 LETTER BOX
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
ON
JACKET PICTURE
ON
ENTER
BLACK LEVEL (COMPONENT OUT):
ON
Setup items
DISPLAY
5
Select an item using X/x, then
press ENTER.
The options for the selected item appear.
Example: “TV TYPE”
1
2
Press DISPLAY when the player is
in stop mode.
The Control Bar appears.
SCREEN SETUP
4:3 LETTER BOX
4:3 LETTER BOX
4:3 PAN SCAN
16:9
TV TYPE:
QUICK
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
BLACK LEVEL (COMPONENT OUT):
ON
Options
Press X/x to select
(SETUP),
then press ENTER.
,continued
49
6
Select a setting using X/x, then
press ENTER.
The setting is selected and setup is
complete.
Example: “16:9”
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
Selected setting
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
SCREEN SETUP
TV TYPE:
16:9
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
ON
JACKET PICTURE
ON
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
BLACK LEVEL (COMPONENT OUT):
ON
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
MENU:
AUDIO:
SUBTITLE:
To turn off the display
Press DISPLAY repeatedly until the display
is turned off.
To enter the Quick Setup mode
◆ OSD (On-Screen Display)
Select “QUICK” in Step 3. Follow from Step
5 of the Quick Setup explanation to make
basic adjustments (page 23).
Switches the display language on the screen.
◆ MENU (DVD only)
You can select the desired language for the
disc’s menu.
To reset all of the “SETUP” settings
If you select “RESET” in Step 3, you can
reset all of the “SETUP” settings on pages 50
to 54 to the default settings. After you select
“RESET” and press ENTER, select “YES”
and press ENTER to reset the settings (it
takes a few seconds to complete), or select
“NO” and press ENTER to return to the
Control Bar. Do not press [/1 when resetting
the player.
◆ AUDIO (DVD only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
◆ SUBTITLE (DVD only)
Switches the language of the subtitle recorded
on the DVD.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according to
the language you selected for the sound track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 60 using the number buttons.
Note
When you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
the DVD, one of the recorded languages will be
automatically selected.
50
Note
Settings for the Display
(SCREEN SETUP)
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
◆ SCREEN SAVER
Choose settings according to the TV to be
connected.
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play back a CD or
DATA CD (MP3 audio) for more than 15
minutes. The screen saver will help prevent
your display device from becoming damaged
(ghosting). Press H to turn off the screen
saver.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
The default settings are underlined.
SCREEN SETUP
TV TYPE:
4:3 LETTER BOX
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
ON
JACKET PICTURE
ON
ON
Turns on the screen saver.
Turns off the screen saver.
BLACK LEVEL (COMPONENT OUT):
ON
OFF
◆ BACKGROUND
Selects the background color or picture on the
TV screen in stop mode or while playing a
CD or DATA CD (MP3 audio).
◆ TV TYPE
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
JACKET
PICTURE
The jacket picture (still picture)
appears, but only when the
jacket picture is already
4:3
LETTER
BOX
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
recorded on the disc (CD-
EXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
4:3
Select this when you connect a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background color is blue.
The background color is black.
portions that do not fit.
BLACK
16:9
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
◆ BLACK LEVEL
Selects the black level (setup level) for the
video signals output from the jacks other than
4:3 LETTER BOX
COMPONENT VIDEO OUT.
.
ON
Sets the black level of the
output signal to the standard
level.
4:3 PAN SCAN
OFF
Lowers the standard black
level. Use this when the picture
becomes too white.
16:9
,continued
51
◆ BLACK LEVEL (COMPONENT OUT)
Selects the black level (setup level) for the
video signals output from the COMPONENT
VIDEO OUT jacks.
Custom Settings (CUSTOM
SETUP)
ON
Sets the black level of the
output signal to the standard
level.
Use this to set up playback related and other
settings.
OFF
Lowers the standard black
level. Use this when the picture
becomes too white.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
The default settings are underlined.
CUSTOM SETUP
AUTO POWER OFF:
AUTO PLAY:
OFF
OFF
BRIGHT
AUTO
OFF
DIMMER:
PAUSE MODE:
TRACK SELECTION:
DISC RESUME:
ON
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
OFF
ON
Switches this function off.
The player enters standby mode
when left in stop mode for more
than 30 minutes.
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
OFF
ON
Switches this function off.
Automatically starts playback
when the player is turned on.
◆ DIMMER
Adjusts the lighting of the front panel display.
BRIGHT
DARK
Makes the lighting bright.
Makes the lighting dark.
52
◆ PAUSE MODE (DVD only)
Selects the picture in pause mode.
Settings for the Sound
AUTO
The picture, including subjects
(AUDIO SETUP)
that move dynamically, is
output with no jitter. Normally
select this position.
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
FRAME
The picture, including subjects
that do not move dynamically,
is output in high resolution.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 49).
◆ TRACK SELECTION (DVD only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD on which multiple audio formats
(PCM, DTS, or Dolby Digital format) are
recorded.
The default settings are underlined.
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
DOLBY SURROUND
ON
D-PCM
OFF
No priority given.
Priority given.
OFF
AUTO
◆ AUDIO ATT (attenuation)
Notes
If the playback sound is distorted, set this
item to “ON.” The player reduces the audio
output level.
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 50).
• If you set “DTS” to “OFF” (page 54), the DTS
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
• If PCM, DTS, and Dolby Digital sound tracks
have the same number of channels, the player
selects PCM, DTS, and Dolby Digital sound
tracks in this order.
This function affects the output of the LINE
OUT L/R (AUDIO) jacks.
OFF
ON
Normally, select this position.
Select this when the playback sound
from the speakers is distorted.
◆ AUDIO DRC (Dynamic Range Control)
(DVD only)
◆ DISC RESUME (DVD/VIDEO CD only)
Switches the Disc Resume setting on or off.
Resume playback can be stored in memory
for up to 6 different DVD/VIDEO CD discs
(page 27).
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.” This affects the
output from the following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (COAXIAL) jack only
when “DOLBY DIGITAL” is set to “D-
PCM” (page 54).
ON
Stores the resume settings in
memory for up to six discs (The
settings remain in memory even
if you select OFF.)
OFF
Does not store the resume
STANDARD Normally select this position.
settings in memory. Playback
restarts at the resume point only
for the current disc in the player.
TV MODE
Makes the low sounds clear
even if you turn the volume
down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
,continued
53
If you connect a component that does not
conform to the selected audio signal, a loud
noise (or no sound) will come out from the
speakers, affecting your ears or causing the
speakers to be damaged.
◆ DOWNMIX (DVD only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 41). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
◆ DOLBY DIGITAL (DVD only)
Selects the type of Dolby Digital signal.
D-PCM
Select this when the player is
connected to an audio
– DIGITAL OUT (COAXIAL) jack when
“DOLBY DIGITAL” is set to “D-PCM”
(page 54).
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
DOLBY
SUR-
ROUND
Normally, select this position.
Multi-channel audio signals are
output to two channels for
enjoying surround sounds.
“DOWNMIX” item in
“AUDIO SETUP” (page 54).
NORMAL Multi-channel audio signals are
downmixed to two channels for
use with your stereo.
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (COAXIAL) jack.
◆ DTS (DVD only)
Selects whether or not to output DTS signals.
ON
Normally select this position. When
you select “ON,” see “Setting the
digital output signal” for further
settings.
OFF
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
OFF The influence of the digital circuit
upon the analog circuit is minimal.
ON
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
Setting the digital output signal
Switches the method of outputting audio
signals when you connect a component such
as an amplifier (receiver) or MD deck with a
digital input jack.
For connection details, see page 18.
Select “DOLBY DIGITAL” and “DTS” after
setting “DIGITAL OUT” to “ON.”
AUDIO SETUP
AUDIO ATT:
AUDIO DRC:
DOWNMIX:
DIGITAL OUT:
DOLBY DIGITAL:
DTS:
OFF
STANDARD
DOLBY SURROUND
ON
D-PCM
OFF
54
Sound
Additional Information
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the amplifier (receiver) (page 20,
21, 22).
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs.
Should any problem persist, consult your
nearest Aiwa dealer (for customers in the
U.S.A only).
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the audio settings (page 54).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
Power
The power is not turned on.
, Check that the AC power cord is connected
securely.
Picture
Sound is noisy.
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 16)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, When playing a CD with DTS sound tracks,
noise will come from the LINE OUT L/R
(AUDIO) jacks (page 25) or DIGITAL
OUT (COAXIAL) jack.
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 53).
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, please try
connecting your player to your TV’s S
VIDEO input (page 16).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” to “TV MODE” (page 53).
, Set “AUDIO ATT” in “AUDIO SETUP” to
“OFF” (page 53).
Operation
The remote does not function.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
Even though you set the aspect ratio in “TV
TYPE” of “SCREEN SETUP,” the picture
does not fill the screen.
, The aspect ratio of the disc is fixed on your
DVD.
, The remote is not pointed at the remote
sensor on the player.
, The batteries in the remote are weak.
,continued
55
The disc does not play.
, The disc is turned over.
Insert the disc with the playback side facing
down on the disc tray.
You cannot perform some functions such
as Stop, Search, Slow-motion Play,
Repeat Play, Shuffle Play, or Program
Play.
, The disc is skewed.
, Depending on the disc, you may not be able
to do some of the operations above. See the
operating manual that comes with the disc.
,
The player cannot play certain discs (page 7).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 3).
, The player cannot play a recorded disc that
is not correctly finalized (page 7).
The language for the sound track cannot
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote (page
28).
, Multilingual tracks are not recorded on the
DVD being played.
The MP3 audio track cannot be played
(page 30).
, The DATA CD is not recorded in the MP3
format that conforms to ISO9660 Level 1/
Level 2 or Joliet.
, The DVD prohibits the changing of the
language for the sound track.
, The MP3 audio track does not have the
extension “.MP3.”
The subtitle language cannot be changed
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG1 Audio Layer 3 data.
, The player cannot play audio tracks in
MP3PRO format.
or turned off.
, Try using the DVD’s menu instead of the
direct selection button on the remote (page
28).
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of the
subtitles.
The title of the MP3 audio album or track
is not correctly displayed.
,
The player can only display numbers and
alphabet. Other characters are displayed as
“*”.
The angles cannot be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote (page
28).
, Multi-angles are not recorded on the DVD
being played.
The disc does not start playing from the
beginning.
, Program Play, Shuffle Play, Repeat Play, or
A-B Repeat Play has been selected (page
32).
, The angle can only be changed when the
“
” indicator lights up on the front panel
display (page 10).
, Resume play has taken effect (page 27).
, The DVD prohibits changing of the angles.
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
set to “ON” (page 52).
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
5 numbers or letters are displayed on the
Playback stops automatically.
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
screen and on the front panel display.
, The self-diagnosis function was activated.
(See the table on page 57.)
56
The disc tray does not open and “LOCKED”
appears on the front panel display.
, Child Lock is set (page 26).
Self-diagnosis Function
(When letters/numbers appear in the
display)
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen and the front panel
display. In this case, check the following
table.
display.
, Contact your Aiwa dealer or local
authorized Aiwa service facility.
“Data error” appears on the TV screen
when playing a DATA CD.
, The MP3 audio track you want to play is
broken.
, The data is not MPEG 1 Audio Layer 3 data.
C:13:50
First three
Cause and/or corrective
characters of action
the service
number
C 13
The disc is dirty.
,Clean the disc with a soft
cloth (page 8).
C 31
The disc is not inserted
correctly.
,Re-insert the disc
correctly.
E XX
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
,Contact your nearest
Aiwa dealer or local
authorized Aiwa service
facility and give the 5-
character service number.
Example: E 61 10
57
The picture data uses the MPEG 2 format, one
of the worldwide standards of digital
compression technology. The picture data is
compressed to about 1/40 (average) of its
original size. The DVD also uses a variable
rate coding technology that changes the data
to be allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more real audio
presence.
Glossary
Chapter (page 10)
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
Dolby Digital (page 22, 54)
Digital audio compression technology
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
developed by Dolby Laboratories. This
technology conforms to 5.1-channel surround
sound. The rear channel is stereo and there is
a discrete subwoofer channel in this format.
Dolby Digital provides the same 5.1 discrete
channels of high quality digital audio found in
Dolby Digital cinema audio systems. Good
channel separation is realized because all of
the channel data are recorded discretely and
little deterioration is realized because all
channel data processing is digital.
DVD-RW (page 6)
A DVD-RW is a recordable and rewritable
disc that is the same size as a DVD VIDEO.
The DVD-RW has two different modes: VR
mode and Video mode. DVD-RWs created in
Video mode have the same format as a DVD
VIDEO, while discs created in VR (Video
Recording) mode allow the contents to be
programmed or edited.
Dolby Surround (Pro Logic) (page 21)
Audio signal processing technology that
Dolby Laboratories developed for surround
sound. When the input signal contains a
surround component, the Pro Logic process
outputs the front, center and rear signals. The
rear channel is monaural.
DVD+RW (page 6)
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
Index (CD)/Video Index (VIDEO CD) (page
37)
A number that divides a track into sections to
easily locate the point you want on a CD or
VIDEO CD. Depending on the disc, no index
may be recorded.
DTS (page 22, 54)
Digital audio compression technology that
Digital Theater Systems, Inc. developed. This
technology conforms to 5.1-channel surround
sound. The rear channel is stereo and there is
a discrete subwoofer channel in this format.
DTS provides the same 5.1 discrete channels
of high quality digital audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
Scene (page 10)
On a VIDEO CD with PBC (playback
control) functions, the menu screens, moving
pictures and still pictures are divided into
sections called “scenes.”
DVD (page 6)
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
The data capacity of a single-layer and single-
sided DVD is 4.7 GB (Giga Byte), which is 7
times that of a CD. The data capacity of a
double-layer and single-sided DVD is 8.5
GB, a single-layer and double-sided DVD is
9.4 GB, and double-layer and double-sided
DVD is 17GB.
Title (page 10)
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
Track (page 10)
Sections of a picture or a music feature on a
CD or VIDEO CD (the length of a song).
58
Specifications
System
Laser: Semiconductor laser
Signal format system: NTSC
General
Power requirements:
120 V AC, 60 Hz
110 to 240 V AC, 50/60 Hz
See page 3 for further information.
Power consumption: 13 W
Dimensions (approx.): 430 ×55.5 ×
Audio characteristics
Frequency response: DVD VIDEO (PCM
96 kHz): 2 Hz to 44 kHz ( 1.0 dB)/DVD
VIDEO (PCM 48 kHz): 2 Hz to 22 kHz
( 0.5 dB)/CD: 2 Hz to 20 kHz ( 0.5 dB)
Signal-to-noise ratio (S/N ratio): 115 dB
(LINE OUT (L/R) AUDIO jacks only)
Harmonic distortion: 0.003 %
234 mm (17 × 2 3/16 × 9 1
in.) (width/
/
4
height/depth) incl. projecting parts
Mass (approx.): 2.2 kg (4 lb 14 oz)
Operating temperature: 5 °C to 35 °C
(41 °F to 95 °F)
Dynamic range: DVD VIDEO: 103 dB/CD:
99 dB
Wow and flutter: Less than detected value
( 0.001% W PEAK)
Operating humidity: 25 % to 80 %
Supplied accessories
See page 15.
The signals from LINE OUT L/R (AUDIO)
jacks are measured. When you play PCM
sound tracks with a 96 kHz sampling
frequency, the output signals from the
DIGITAL OUT ( COAXIAL) jack are
converted to 48 kHz sampling frequency.
Specifications and design are subject to
change without notice.
ENERGY STARR is a U.S. registered mark.
As an ENERGY STARR Partner, Sony
Corporation has determined that this product
meets the ENERGY STARR guidelines for
energy efficiency.
Outputs/Inputs
(Jack name: Jack type/Output or Input level/
Load impedance)
LINE OUT (AUDIO): Phono jack/2 Vrms/
10 kilohms
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
COMPONENT VIDEO OUT (Y, PB, PR):
Phono jack/Y: 1.0 Vp-p/PB, PR:
0.65 Vp-p/75 ohms
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/Y:
1.0 Vp-p, C: 0.286 Vp-p/75 ohms
59
Language Code List
For details, see pages 41, 44, 50.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
60
Index
Numerics
F
S
16:9 51
Fast forward 36
Fast reverse 36
Freeze Frame 36
Front panel display 10
S VIDEO output 16
Scan 36
4:3 LETTER BOX 51
4:3 PAN SCAN 51
5.1 Channel Surround 41
SCENE 37
Scene 10, 58
SCREEN SAVER 51
SCREEN SETUP 51
Searching 36
A
H
A-B REPEAT 35
ALBUM 37
Handling discs 8
Hooking up 15
SETUP 49
Album 30
ANGLE 45
Setup Display 49
SHUFFLE 33
Shuffle Play 33
Slow-motion Play 36
Speakers
Hooking up 18
SUBTITLE 44, 50
SURROUND 18, 42
I
INDEX 37
Index 58
AUDIO 41, 50
AUDIO ATT 53
AUDIO DRC 53
AUDIO SETUP 53
AUTO PLAY 52
AUTO POWER OFF 52
Instant Replay 26
Instant Search 26
L
LANGUAGE SETUP 50
Locating
B
T
a specific point by watching
the TV screen 36
BACKGROUND 51
Batteries 15
TIME/TEXT 38, 39
TITLE 37
BLACK LEVEL 51
Title 10, 58
M
TOP MENU 28
TRACK 37
C
MENU 50
MP3 6, 30, 56
CD 6, 25
Track 10, 30, 58
TRACK SELECTION 53
Troubleshooting 55
TV TYPE 51
CHAPTER 37
Chapter 10, 58
Child Lock 26
Connecting 16
Continuous play
CD/VIDEO CD 25
DVD 25
N
NUMBER INPUT 38
O
U
On-screen display
Control Bar display 13
Setup Display 49
OSD 50
Usable discs 6
V
Control Bar 13
CUSTOM 49
CUSTOM SETUP 52
VIDEO CD 6, 25
Virtual Surround 42
P
PARENTAL CONTROL 46
PAUSE MODE 53
PBC Playback 29
PICTURE MODE 44
PRO LOGIC 21, 54, 58
PROGRAM 32
D
DATA CD 6, 30
DIGITAL OUT 54
Digital output 54
DIMMER 52
DISC RESUME 27, 53
Program Play 32
Display
Control Bar display 13
Front panel display 10
Setup Display 49
DOLBY DIGITAL 22, 41,
54, 58
Q
QUICK 50
Quick Setup 23, 50
R
DOWNMIX 54
DTS 22, 41, 54, 58
DVD 6, 25
Remote 15
REPEAT 34
Repeat Play 34
RESET 50
Resume Play 27
DVD+RW 6, 26, 58
DVD’s Menu 28
DVD-RW 6, 26, 58
61
Printed on 100% recycled magazine paper.
Printed using VOC (volatile organic compound)-free vegetable oil based ink.
Sony Corporation Printed in Malaysia
|