User Manual
PCM-9587
Onboard Intel® Celeron M EBX
SBC with Audio, VGA, LCD,
SATA
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
„
„
„
„
„
„
•1 PCM-9587 all-in-one single board computer
•1 CD disk for utility and drivers
•1 startup manual
•1 Mini Jumper*10 PCS Package (p/n: 9689000002)
1 ATX power cable (p/n:1700001112)
1 X Heatsink (50*50*30mm)
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately.
Order Information
L2
Cache
10/100
LAN
RS-232/ LPT/FDD/
PC/ PCI Mini Thermal Operation
Part No.
CPU
CRT LVDS DVI TV out
Audio USB2.0 RS-232
CF SATA
422/485
KB/MS
104+ Slot PCI Solution
Temp.
0~60°C
0~60°C
PCM-9587F-M0A1E Celeron M 600 MHz
PCM-9587F-S0A1E Celeron M 1.0 GHz
512 KB Yes 36-bit Yes Optional
0 KB Yes 36-bit Yes Optional
1
1
1
1
Yes
Yes
Yes
Yes
4
4
4
4
3
3
3
3
1
1
1
1
Yes
Yes
Yes
Yes
Yes
2
2
2
2
Yes
Yes
Yes
Yes
1
1
1
1
1
1
1
1
Passive
Passive
Yes
PCM-9587Z-M0A1E Celeron M 600 MHz
PCM-9587Z-S0A1E Celeron M 1.0 GHz
512 KB Yes 36-bit Yes Optional
0 KB Yes 36-bit Yes Optional
Yes
Passive -20~80°C
Passive -20~80°C
Yes
PS: 48-bit LVDS possible btu need to confirm with AE for evaluation
Optional accessories
Part No.
Description
PCM-10586-6200E
17030506
Wiring kit for PCM-9582/9587
TV-out cable
1703100260
USB cable (26 cm)
USB cable (12 cm)
1703100121
PCM-110-00A3E
PCM-120-00A3E
PCM-200-00A2E
MIO-3120-00A1E
MIO-3121-00A1E
MIO-3140-00A1E
MIO-3150-00A1E
MIO-3130-00A1E
MIO-3131-00A1E
1-slot PCI riser card for 5.25” biscuits
2-slot PCI riser card for 5.25” biscuits
PCI-104 to PCI bus module
Mini PCI interface to Wireless 802.11 b/g communication module
Mini PCI to 4 COM Module
Mini PCI interface to SATA storage module
Mini PCI interface to video capture module
Mini PCI interface to Dual LAN Communication Module
Mini PCI interface to Single Giga LAN Communication Module
iii
PCM-9587 User Manual
Declaration of Conformity
FCC Class A
This device complies with the requirements in part 15 of the FCC rules: Operation is
subject to the following two conditions:
1.This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.
Technical Support and Assistance
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
PCM-9587 User Manual
iv
Features.................................................................................................... 2
Specifications............................................................................................ 2
Board layout: dimensions.......................................................................... 4
2.19.2 Network boot............................................................................... 15
v
PCM-9587 User Manual
DIO connector (CN19) ............................................................................ 16
System test and initialization................................................................... 22
4.2.11 Set Password.............................................................................. 27
Save & Exit Setup................................................................................... 28
5.1.1 Chipset........................................................................................ 30
5.1.3 Display types .............................................................................. 30
PCM-9587 User Manual
vi
Features.................................................................................................. 40
Installation of Ethernet Driver.................................................................. 40
Timer...................................................47
.................................................................................. 52
DVI Connector (CN9).............................................................................. 55
vii
PCM-9587 User Manual
Mechanical Drawings.............................................................................. 72
PCM-9587 User Manual
viii
1.1 Introduction
The PCM-9587 series is a EBX SBC (Single Board Computer) designed with the
powerful Intel Celeron M processor, and Intel 852GM and 6300ESB chipsets, which
supports Dynamic Video Memory Technology For maximum performance. PCM-
9587 also supports one 184 PIN DIMM socket for ECC DDR memory up to 1GB.
These chipsets are specifically for embedded computing and provide an optimized
on-board integrated graphics solution.
Other on-board features include 1 EIDE, 2 SATAs, 1 FDD, 1 LPT, 4 USB2.0, 4 serial
ports(3 x RS-232 and 1 x RS-232/422/485), PS/2 KeyBoard/mouse, watchdog. The
SSD solution supports Type I/II CompactFlash cards.
The PCM-9587 complies with EBX form factor (Embedded Board eXpandable). It is
compact and suitable for embedded applications, yet large enough to contain the
functions of a full embedded computer system. The EBX system expansion is based
on popular existing industry standards-PC/104TM, PCI, and PC/104-PlusTM, hence
the PC/104-Plus interface on PCM-9587 brings the advantages of a wide variety of
embedded system expansion modules. The expandability can also be fulfilled by the
MiniPCI socket on the solder side.
1.2 Features
„
Embedded Intel® Celeron® M 600 MHz/Celeron® M 1.0 GHz
„
Supports ECC DDR memory up to 1 GB, accept 128/256/512/1024 MB
DDR200/266 DRAM
„
„
„
„
„
„
EBX form factor standard and support for PC/104-Plus bus
Supports 10/100Base-T Ethernet
Supports up to two channel 36-bit LVDS interface
Wide temperature optional
2 x SATA 150 (RAID 0/1), 4 x COM, 4 x USB 2.0, 8 bit GPIO
Support PC/104-Plus (PCI + 8-bit ISA), Mini PCI and 1 x PCI Slot
1.3 Specifications
Standard SBC Functions
„
„
„
CPU: Supports onboard Celeron® M processor
BIOS: Award 4 Mbit byte Flash memory
System memory: One 184 pin DIMM sockets, support ECC
Double Data Rate (DDR)128 MB to 1 GB, accepts 128/256/512/1000 MB
DDR200/266 DRAM.
„
„
System chipset:Intel 852GM GMCH/6300ESB Chipset 400MHz FSB
Enhanced IDE interface: One Enhanced IDE interface supports 2 IDE devices.
PIO mode 3 or mode 4, Ultra DMA 100 transfer. 2 Serial ATA standard connec-
tor to support SATA 150
„
„
„
„
FDD interface: Supports one FDD
Serial ports: Three serial RS-232 ports, one serial RS-232/422/485 ports
Parallel port: One parallel port, supports SPP/EPP/ECP mode
Keyboard/mouse connector: Supports standard PS/2 keyboard and a PS/2
mouse
„
Power management: APM Rev. 1.2 compliant power management ACPI sup-
port
PCM-9587 User Manual
2
„
Watchdog timer: Winbond W83627, 255 levels timer interval, setup by soft-
ware
„
„
„
„
USB: Four USB 2.0 compliant host ports
IrDA: N/A
GPIO: 8-bit general purpose input/output
Expansion: PC/104 Plus(support 8bit ISA, not support ISA DMA mode), PCI
and miniPCI
Solid State Disk
„
Supports one 50-pin socket for CFC type I/II
VGA/LCD Interface
„
„
Chipset: Intel 852GM
Frame buffer: Optimized Shared Memory Architecture, supports up to 64MB
frame buffer using system memory
„
„
Interface: 4x AGP VGA/LVDS interface
Display mode: CRT Modes: pixel resolution up to 1600 x 1200 at 85-Hz and
2048 x 1536 at 75-Hz
„
„
LCD mode: Dual channel LVDS panel support up to UXGA panel resolution
with frequency range from 25-MHz to 112-MHz
LVDS: Supports 2 channel (48-bit) LVDS LCD panel
TV-Out/DVI (TV out optional by request)
„
„
„
Chipset: Chrontel CH7009
Supports composite, s-video or RGB output
Supports NTSC and PAL formats
Ethernet interface
„
„
„
„
„
„
Chipset:
Intel 82551ER /82551QM optional
Ethernet interface:
IEEE 802.3u 100 BASE-T Fast Ethernet compatible (PCM-9587)
I/O address switchless setting
Built-in boot ROM
Audio Function
„
„
„
Chipset: 6300ESB, Audio codec ALC 650
Audio controller: AC’97 3D surround stereo sound
Supports Speaker out, CD-input, Line-in, Line-out, Microphone
Mechanical and Environmental
„
„
„
„
„
„
„
„
Dimensions: (L x W)203 x 146 mm (8" x 5.75")
Power supply Voltage:ATX, with Vcore 2 phase, +5V power only can work
Power Requirement: (Celeron M 600 with 256MB)
Max: 2.63A@ 5V, 0.03A @ 12V
Typical: 2.62A@ 5V, 0.03A @ 12V
Operating temperature:0 ~ 60° C (32~140° F)
Operating Humidity:0% ~ 90% Relative Humidity, non-condensing
Weight: 0.85 kg (weight of total package)
3
PCM-9587 User Manual
2.1 Jumpers
The PCM-9587 has a number of jumpers that allow you to configure your system to
suit your application. The table below lists the functions of the various jumpers.
Table 2.1: Jumpers
Label
Function
J1
J2
J3
J5
LCD Voltage Select
PC104+ VIO Select
Clear CMOS function Select
COM2 RS232/422/485 function Select
2.1.1 Jumpers setting drawing
Table 2.2: J1: LCD Voltage Select
PIN
FUNCTION
1-2
2-3
+3.3 V*
+5 V
1
2
3
1
2
3
Table 2.3: J2: PC104+ VIO Select
PIN
FUNCTION
1-2
2-3
VIO = +5 V *
VIO = +3.3 V
1
2
3
1
2
3
Table 2.4: J3: Clear CMOS function Select
PIN
FUNCTION
1-2 Open
1-2 Close
Normal*
Clear CMOS
1
2
PCM-9587 User Manual
6
Table 2.5: J5: COM2 RS 232/422/485 Select
PINS
RS-232
RS-422
RS-485
1,2
Open
Open
Close
Close
Close
Open
Open
Close
Close
Open
Open
Open
Close
Open
Open
Open
Close
Close
Open
Open
Close
Close
Close
Open
Open
Open
Open
Close
Close
Open
Open
Close
Close
3,4
5,6
7,9
8,10
9,11
10,12
13,15
14,16
15,17
16,18
2 .. .. .. .. .. .. .. 18
○ ○ ■ ■ ■ ○ ■ ■ ○
RS-232
■
□ ○
■ ■ ○ ■ ■ ○
1 .. .. .. .. .. .. .. 17
2
.. .. .. .. .. .. .. 18
○ ■ ○ ○ ■ ■ ○ ■ ■
RS-422
RS-485
■
□
○ ○ ■ ■ ○ ■ ■
1
.. .. .. .. .. .. .. 17
2 .. .. .. .. .. .. .. 18
■ ○ ○ ○ ■ ■ ○ ■ ■
■
○ ○ ○ ■ ■ ○ ■ ■
1 .. .. .. .. .. .. .. 17
7
PCM-9587 User Manual
2.2 Connectors
On-board connectors link the PCM-9587 to external devices such as hard disk
drives, a keyboard, or floppy drives. The table below lists the function of each of the
board’s connectors.
Table 2.6: Connectors
Label
CN1
Function
LCD Backlight connector
TV-out connector (TV out optional by request)
CD-IN connector
CN2
CN3
CN4
Audio output connector
Power input connector
-12V and -5V connector
VGA connector
CN5
CN6
CN7
CN8
LVDS connector
CN9
DVI connector
CN10
CN11
CN12
CN13
CN14
CN15
CN16
CN17
CN18
CN19
CN20
CN21
CN22
CN23
CN24
CN25
CN26
CN27
CN28
CN29
CN30
PCI1
Gigabit LAN connector(Optional)
10/100M LAN connector
Gigabit LAN led connector(Optional)
System FAN connector
Floppy connector
Primary HDD connector
Printer port connector
PC104 and PC104+ connector
USB port 3/4
DIO connector
USB port 1/2
COM port 1/2/3/4 connector
Front panel connector
SATA connector 1
SATA connector 2
CPU FAN connector
Extension SMBUS connector
KB / Mouse connector
CPU FAN connector (wafer box)(Optional)
MINI-PCI connector
CompactFlash card connector
Extension PCI slot
PCM-9587 User Manual
8
2.4 Setting Jumpers
You may configure your card to match the needs of your application by setting jump-
ers. A jumper is a metal bridge used to close an electric circuit. It consists of two
metal pins and a small metal clip (often protected by a plastic cover) that slides over
the pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper, you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2 and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
open
closed
closed 2-3
The jumper settings are schematically depicted in this manual as follows:.
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your application,
contact your local distributor or sales representative before you make any changes.
Generally, you simply need a standard cable to make most connections.
2.5 Clear CMOS (J3)
Warning! To avoid damaging the computer, always turn off the power supply
before setting “Clear CMOS.” Before turning on the power supply, set
the jumper back to “3.0 V Battery On.”
This jumper is used to erase CMOS data and reset system BIOS information.
The procedure for clearing CMOS is:
1. Turn off the system.
2. Push J3.
3. Turn on the system. The BIOS is now reset to its default setting.
PCM-9587 User Manual
10
2.6 Installing DIMMs
The procedure for installing DIMMs is described below. Please follow these steps
carefully. The number of pins are different on either side of the breaks, so the module
can only fit in one way. DIMM modules have different pin contacts on each side, and
therefore have a higher pin density.
1. Make sure that the two handles of the DIMM socket are in the “open” position.
i.e. The handles remain leaning outward.
2. Slowly slide the DIMM module along the plastic guides on both ends of the
socket.
3. Press the DIMM module right down into the socket, until you hear a click. This is
when the two handles have automatically locked the memory module into the
correct position of the socket.
To remove the memory module, just push both handles outward, and the module will
be ejected from the socket.
2.7 IDE, CDROM hard drive connector (CN15)
The PCM-9587 provides 1 IDE channels which you can attach up to two Enhanced
Integrated Device Electronics hard disk drives or CDROM to the PCM-9587’s internal
controller. The PCM-9587's IDE controller uses a PCI interface. This advanced IDE
controller supports faster data transfer, PIO mode 3, mode 4 and UDMA/100.
2.7.1 Connecting the hard drive
Wire number 1 on the cable is red or blue, and the other wires are gray.
1. Connect one end of the cable to CN15. Make sure that the red (or blue) wire
corresponds to pin 1 on the connector, which is labeled on the board (on the
right side).
2. Plug the other end of the cable into the Enhanced IDE hard drive, with pin 1 on
the cable corresponding to pin 1 on the hard drive. (See your hard drive’s docu-
mentation for the location of the connector.)
2.8 Solid State Disk
The PCM-9587 provides a CompactFlash™ card socket.
2.8.1 CompactFlash (CN30)
The CompactFlash card shares a secondary IDE channel which can be enabled/dis-
abled via the BIOS settings.
11
PCM-9587 User Manual
2.9 Floppy drive connector (CN14)
You can attach up to two floppy drives to the PCM-9587’s on-board controller. This is
useful with 34 pin dual FDD cable (part no:1701340603).
You can use any combination of 5.25”(360 KB and 1.2MB) and/or 3.5”(720 KB,
1.44MB, and 2.88 MB) drives. An appropriate 34 pin flat cable is required.
2.9.1 Connecting the floppy drive
1. Plug the 34-pin dual FDD-cable connector into CN14 of PCM-9587 board. Make
sure that the red wire corresponds to pin one on the connector.
2. Attach the appropriate connector at the end of the cable to the floppy drive(s).
You can use only one connector in the set. The set on the end (after the twist in
the cable) connects to A: drive. The set in the middle connects to the B: drive.
If you are connecting a 3.5” floppy drive, you may have trouble determining which pin
is number one. Look for a number printed on the circuit board indicating pin number
one. In addition, the connector on the floppy drive may have a slot. When the slot is
up, pin number one should be on the right. Check the documentation that came with
the drive for more information.
If you desire, connect the B: drive to the connectors in the middle of the cable as
described above.
In case you need to make your own cable, you can find the pin assignments for the
board’s connector in Appendix B.
2.10 Parallel port connector (CN16)
Normally, the parallel port is used to connect the card to a printer. The PCM-9587
includes a multi-mode (ECP/EPP/SPP) parallel port accessed via CN16 and a 26-pin
flat-cable connector. You will need an adapter cable if you use a traditional DB-25
connector. The adapter cable has a 26-pin connector on one end, and a DB-25 con-
nector on the other.
The parallel port is designated as LPT1, and can be disabled or changed to LPT2 or
LPT3 in the system BIOS setup.
The parallel port interrupt channel is designated to be IRQ7.
You can select ECP/EPP/SPP DMA channel via BIOS setup.
2.11 Keyboard and PS/2 mouse connector (CN27)
The PCM-9587 board provides a keyboard connector that supports both a keyboard
and a PS/2 style mouse. In most cases, especially in embedded applications, a key-
board is not used. If the keyboard is not present, the standard PC/AT BIOS will report
an error or fail during power-on self-test (POST) after a reset. The PCM-9587’s BIOS
standard setup menu allows you to select “All, But Keyboard” under the “Halt On”
selection. This allows no-keyboard operation in embedded system applications, with-
out the system halting under POST.
PCM-9587 User Manual
12
2.12 Front Panel Connector (CN22)
Next, you may want to install external switches to monitor and control the PCM-9587.
These features are optional: install them only if you need them. The Front Panel con-
nector (CN22) is a 14-pin male, dual in-line header. It provides connections for a hard
disk access indicator, LAN Act., LAN Link, hardware reset, ATX power ON/OFF
switch connector, and power on indicator.
2.12.1 Power & HDD LED (pin 1-4 of CN22)
The HDD LED indicator for hard disk access is an active low signal (24 mA sink rate).
Power supply activity LED indicator.
2.12.2 Reset switch (pin 13-14 of CN22)
If you install a reset switch, it should be an open single pole switch. Momentarily
pressing the switch will activate a reset. The switch should be rated for 10 mA, 5 V.
2.13 Power connectors (CN25,CN5)
2.13.1 ATX power connector, +5V (CN5)
Supplies main power to the PCM-9587 (+5V) and to devices that require it.
2.13.2 CPU Fan power supply connector (CN25)
Provides power supply +12V to CPU cooling fan, and fan speed detects signal input.
2.14 ATX power ON/OFF switch con. pin 11-12 of
CN22
2.14.1 ATX feature (CN5) & soft power switch (CN22)
The PCM-9587 can support an advanced soft power switch function, if an ATX power
supply is used. To enable the soft power switch function connect the power on/off
button to CN22. (A momentary type of button should be used.)
Note!
Make sure that the ATX power supply can take at least a 10 mA load on
the 5 V standby lead (5VSB). If not, you may have difficulty powering on
your system.
13
PCM-9587 User Manual
2.15 Audio AC'97 Link interfaces (CN4)
The PCM-9587 is equipped with a high quality audio interface, which provides 16-bit
CD-quality recording and playback as well as OPL3 compatible FM music. It is sup-
ported by all major operating systems and is completely compatible with Sound
Blaster Pro.
2.15.1 Audio connector(CN4)
The PCM-9587 provides all major audio signals on a 16-pin flat-cable connector,
CN4. The audio signals include Microphone in (mono), Line in (stereo), Line out (ste-
reo) and Speaker out (stereo). You will need an adapter cable if you use traditional
jack connectors for these audio signals.
2.15.2 CD audio-in connector (CN3)
All CD-ROM drives can provide analog audio signal output when used as a music CD
player. The CN3 on PCM-9587 is a connector to input CD audio signal into the audio
controller. The audio cable of your CD-ROM drive will be used to connect to CN3.
2.16 COM port connector (CN21)
The PCM-9587 provides four RS-232 serial ports (COM1,3,4:RS-232, COM2: RS-
232/422/485) in one COM port connector. The COM port connector is a 40-pin,
20*2P 180D(M) 2.0mm, connector. It provides connections for serial devices (a
mouse, etc.) or a communication network. You can find the pin assignments for the
COM port connector in Appendix C. COM2 can be configured to operate in RS-
232,RS-422, or RS-485 mode. This is done via J5.
2.17 VGA/LVDS interface connections (CN7,
CN8,CN9)
The PCM-9587’s AGP SVGA interface can drive conventional CRT displays and is
capable of driving a wide range of LVDS flat panel displays. The board has three con-
nectors to support these displays: one for standard CRT VGA monitors, one for LVDS
type LCD panels and one for DVI type LCD panels.
2.17.1 CRT display connector (CN7)
CN7 is a 16-pin, dual-inline header used for conventional CRT displays. A simple
one-to-one adapter can be used to match CN7 to a standard 15-pin D-SUB connec-
tor commonly used for VGA. Users can drive a standard progressive scan analog
monitor with pixel resolution up to 1600 x 1200 at 85 Hz and up to 2048 x 1536 at 75
Hz. Pin assignments for CRT display connector CN7 are detailed in Appendix B.
2.17.2 LVDS LCD panel connector (CN8)
The PCM-9587 uses the Intel 852 GM chipset that supports single- or dual-channel
LVDS panel up to UXGA panel resolution with frequency range from 15MHz to
112MHz.
The PCM-9587 supports single or dual-channel LVDS panels up to UXGA panel res-
olution with frequency range from 25MHz to 112MHz. The display mode can be 2
channel (2 x 18bit) LVDS LCD panel displays, or optional (2 x 24bit) LVDS LCD panel
display. Users can connector to either an 18, 24, 36 or 48bit LVDS LCD with CN8
PCM-9587 User Manual
14
2.17.3 DVI LCD panel connector(CN9)
Digital Visual Interface (DVI) is the standard interface for high-performance connec-
tion between PCs and Flat Panel Displays, Digital CRT displays, Projectors, and
HDTV. The PCM-9587 is able to drive a DVI connector display at a pixel resolution up
to 1600 x 1200 at 85Hz.
Panel type and Resolution mode selection
Customer can select display type and boot number from BIOS menu selection.
Table 2.7: CN9: DVI connector
PIN
Signal
PIN
Signal
1
C0#
C0
2
VCC_DVI
CK#
3
4
5
GND
C1#
C1
6
CK
7
8
GND
9
10
12
14
16
18
20
DVI_CLK
DVI_DATA
HP_DET
MI2C_DATA
MI2C_CLK
NC
11
13
15
17
19
GND
C2#
C2
VCC_DVI
NC
2.18 TV-out interface (CN2) (TV out optional by
request)
The PCM-9587 board provides TV-out function via CN2. This consists of a 5-pin
wafer box header. Output supports composite video, S-video and SCART(RBG). TV-
out generators use both NTSC and PAL formats.It supports up to 1024 by 768 with
full vertical and horizontal underscan capability.
To set up your video interface run the appropriate installation program located on the
utility disk.
2.19 Ethernet configuration (CN11)
The PCM-9587 is equipped with a high performance 32-bit PCI-bus Ethernet inter-
face which is fully compliant with IEEE 802.3U 10/100Mbps CSMA/CD standards. It
is supported by all major network operating systems.
2.19.1 100Base-T connector (CN11)
10/100Base-T connects to the PCM-9587 via an adapter cable to a 10-pin polarized
header (CN11).
2.19.2 Network boot
The Network Boot feature can be utilized by incorporating the Boot ROM image files
for the appropriate network operating system. The Boot ROM BIOS files are included
in the system BIOS, which is on the utility CD disc.
15
PCM-9587 User Manual
2.20 USB connectors (CN18,CN20)
The PCM-9587 board provides up to four USB (Universal Serial Bus) 2.0 ports. This
gives complete Plug and Play, and hot attach/detach for up to 127 external devices.
The USB interfaces comply with USB specification Rev. 1.1, and are fuse protected.
The PCM-9587 support three 5 x2 pin header connector for USB1,2 (CN20),
USB3,4(CN18). You will need an USB cable if you use USB connectors. The USB
interfaces can be disabled in the system BIOS setup.
Table 2.8: CN18: USB port 3/4
PIN
Signal
PIN
Signal
1
3
5
7
9
VCC
2
VCC
DAT2-
DAT2+
GND
4
DAT3-
DAT3+
GND
NC
6
8
GND
10
Table 2.9: CN20: USB PORT 1/2
PIN
Signal
PIN
Signal
1
3
5
7
9
VCC
2
VCC
DAT0-
DAT0+
GND
4
DAT1-
DAT1+
GND
NC
6
8
GND
10
2.21 LCD Backlight connector (CN1)
The LCD inverter is connected to CN1 via a 5-pin connector to provide +5V/+12V
power.
2.22 SATA Connector (CN23, CN24)
PCM-9587 can support Serial ATA by two COMAX C504C connectors (SA1, SA2),
data transfer rates up to 150 Mbyte/s, enabling very fast data and file transfer, and
independent DMA operation on two ports. It also supports alternate Device ID and
RAID Class Code option for support of Soft RAID.
2.23 DIO connector (CN19)
The PCM-9587 supports DIO interface by CN19, which is a 7 x 2 dual line pin header,
supply 8 general purpose input or output ports.
2.24 -12V and -5V connector (CN6)
Supply -5V/-12V for ISA/PCI device.
2.25 Extension SMBUS connector (CN26)
4-pin connector reserved for extra SMBus device.
PCM-9587 User Manual
16
2.26 System FAN connector (CN13)
The board supports one system housing cooling fan connector on the motherboard.
The connector is 3-pin headers and support fan speed monitoring. A temperature
monitor detects the internal system temperatures, which is displayed in the PC
Health section of the CMOS Setup Utility.
Table 2.10: CN13: System FAN connector
PIN
Signal
1
2
3
GND
+12V
Detection
Note!
PCM-9587 ISA bus only support 8 bit.
17
PCM-9587 User Manual
PCM-9587 User Manual
18
Chapter
3
3
Software
Configuration
This chapter details the software
configuration information. It
shows you how to configure the
card to match your application
requirements. The AWARD Sys-
tem BIOS is covered in Chapter 4.
Sections include:
„ Introduction
„ Connections for standard LCDs
„ Ethernet interface configura-
tion.
3.1 Introduction
The PCM-9587 system BIOS and custom drivers are located in a 512 Kbyte, Flash
ROM device, designated U6. A single Flash chip holds the system BIOS, VGA BIOS
and network Boot ROM image. The display can be configured via CMOS settings.
This method minimizes the number of chips and difficulty of configuration. To set dif-
ferent types of LCD panels, please choose “panel type” from the “integrated peripher-
als” menu in CMOS setup.
3.2 Connections to Standard LCDs
The following tables illustrate typical LCD connection pinouts for the PCM-9587.
3.2.1 LG LM150X06 (1024x768(16 colors) LVDS LCD)
Table 3.1: Connections to LCD/ Flat Panel (CN8)
LCD Connector
Flat Panel Connector
Unipac-UB104S01
DF-13 40P
Pin
Signal
Pin
Signal
1
VCC
1
3.3V
2
VCC
2
3.3V
3
GND
3
GND
4
GND
4
GND
5
RxIN0-
RxIN0+
GND
7
LVDS_YAM0R
LVDS_YAP0R
GND
6
9
7
11
13
15
17
19
21
23
25
27
29
8
RxIN1-
RxIN1+
GND
LVDS_YAM1R
LVDS_YAP1R
GND
9
10
11
12
13
14
15
16
17
18
19
20
RxIN2-
RxIN2+
GND
LVDS_YAM2R
LVDS_YAP2R
GND
CKIN-
CKIN+
GND
LVDS-CLKAMR
LVDS-CLKAPR
GND
NC
NC
GND
33
34
GND
GND
GND
* LCD connector type: HRS DF 19K-20P-1H or compatible
PCM-9587 User Manual
20
4.1 System test and initialization
These routines test and initialize board hardware. If the routines encounter an error
during the tests, you will either hear a few short beeps or see an error message on
the screen. There are two kinds of errors: fatal and non-fatal. The system can usually
continue the boot up sequence with non-fatal errors. Non-fatal error messages usu-
ally appear on the screen along with the following instructions:
press <F1> to RESUME
Write down the message and press the F1 key to continue the bootup sequence.
4.1.1 System configuration verification
These routines check the current system configuration against the values stored in
the board's CMOS memory. If they do not match, the program outputs an error mes-
sage. You will then need to run the BIOS setup program to set the configuration infor-
mation in memory.
There are three situations in which you will need to change the CMOS settings:
1. You are starting your system for the first time
2. You have changed the hardware attached to your system
3. The CMOS memory has lost power and the configuration information has been
erased.
The PCM-9587 Series' CMOS memory has an integral lithium battery backup. The
battery backup should last ten years in normal service, but when it finally runs down,
you will need to replace the complete unit.
4.2 Award BIOS setup
Award’s BIOS ROM has a built-in Setup program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed
CMOS RAM so that it retains the Setup information when the power is turned off.
4.2.1 Entering setup
Power on the computer and press <Del> immediately. This will allow you to enter
Setup.
Figure 4.1 BIOS setup program initial screen
PCM-9587 User Manual
22
4.2.2 Standard CMOS Features setup
When you choose the Standard CMOS Features option from the Initial Setup Screen
menu, the screen shown below is displayed. This standard Setup Menu allows users
to configure system components such as date, time, hard disk drive, floppy drive and
display. Once a field is highlighted, on-line help information is displayed in the left
bottom of the Menu screen.
Figure 4.2 CMOS Features setup
4.2.3 Advanced BIOS Features setup
By choosing the Advanced BIOS Features Setup option from the Initial Setup Screen
menu, the screen below is displayed. This sample screen contains the manufac-
turer’s default values for the PCM-9587 Series.
Figure 4.3 Advanced BIOS Features setup
23
PCM-9587 User Manual
4.2.4 Advanced Chipset Features setup
By choosing the Advanced Chipset Features option from the Initial Setup Screen
menu, the screen below is displayed. This sample screen contains the manufac-
turer’s default values for the PCM-9587 Series.
Figure 4.4 Advanced Chipset Features setup
4.2.5 Integrated Peripherals
Choosing the Integrated Peripherals option from the Initial Setup Screen menu
should produce the screen below. Here we see the manufacturer’s default values for
the PCM-9587 Series.
Figure 4.5 Integrated Peripherals
PCM-9587 User Manual
24
4.2.6 Power Management Setup
By choosing the Power Management Setup option from the Initial Setup Screen
menu, the screen below is displayed. This sample screen contains the manufac-
turer’s default values for the PCM-9587 Series.
Figure 4.6 Power Management Setup
4.2.7 PnP/PCI Configurations
By choosing the PnP/PCI Configurations option from the Initial Setup Screen menu,
the screen below is displayed. This sample screen contains the manufacturer’s
default values for the PCM-9587 Series.
Figure 4.7 PnP/PCI Configurations
25
PCM-9587 User Manual
4.2.8 PC Health Status
The PC Health Status option displays information such as CPU and motherboard
temperatures, fan speeds, and core voltage.
Figure 4.8 PC Health Status
4.2.9 Frequency/Voltage Control
By choosing the Frequency/Voltage Control option from the Initial Setup Screen
menu, the screen below is displayed. This sample screen contains the manufac-
turer’s default values for the PCM-9587.
Figure 4.9 Frequency/Voltage Control
Caution! Incorrect settings in Frequency/Voltage Control may damage the sys-
tem CPU, video adapter, or other hardware.
PCM-9587 User Manual
26
4.2.10 Load Optimized Defaults
Figure 4.10 Load Optimized Defaults
Load Optimized Defaults loads the default system values directly from ROM. If the
stored record created by the Setup program should ever become corrupted (and
therefore unusable), these defaults will load automatically when you turn the PCM-
9587 Series system on.
4.2.11 Set Password
Note!
To enable this feature, you should first go to the Advanced BIOS Fea-
tures menu, choose the Security Option, and select either Setup or Sys-
tem, depending on which aspect you want password protected. Setup
requires a password only to enter Setup. System requires the password
either to enter Setup or to boot the system.
A password may be at most 8 characters long.
To Establish Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password,” enter the desired password and press
<Enter>.
3. At the “Confirm Password” prompt, retype the desired password, then press
<Enter>.
4. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
27
PCM-9587 User Manual
To Change Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password,” enter the existing password and press
<Enter>.
3. You will see “Confirm Password” Type it again, and press <Enter>.
4. Select Set Password again, and at the “Enter Password” prompt, enter the new
password and press <Enter>.
5. At the “Confirm Password” prompt, retype the new password, and press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
To Disable Password
1. Choose the Set Password option from the CMOS Setup Utility main menu and
press <Enter>.
2. When you see “Enter Password,” enter the existing password and press
<Enter>.
3. You will see “Confirm Password.” Type it again, and press <Enter>.
4. Select Set Password again, and at the “Enter Password” prompt, don’t enter
anything; just press <Enter>.
5. At the “Confirm Password” prompt, again don’t type in anything; just press
<Enter>.
6. Select Save to CMOS and EXIT, type <Y>, then <Enter>.
4.3 Save & Exit Setup
If you select this option and press <Y> then <Enter>, the values entered in the setup
utilities will be recorded in the chipset’s CMOS memory. The microprocessor will
check this every time you turn your system on and use the settings to configure the
system. This record is required for the system to operate.
4.3.1 Exit Without Saving
Selecting this option and pressing <Enter> lets you exit the Setup program without
recording any new values or changing old ones.
PCM-9587 User Manual
28
5.1 Introduction
The PCM-9587 has an onboard PCI/AGP flat panel/VGA interface. The specifications and
features are described as follows:
5.1.1 Chipset
The PCM-9587 uses a Intel Montara-GM/GM+ GMCH chipset for its graphic controller. It sup-
ports LVDS LCD displays, conventional analog CRT monitors, DVI connection, and TV-out
function.
5.1.2 Display memory
The Intel Montara-GM/GM+ GMCH chip can support up to 64MB frame buffer shared with
system memory; the VGA controller can drive CRT displays up to 1600 x 1200 at 85-Hz and
2048 x 1536 at 75-Hz, color panel displays in LVDS model with resolutions up to UGXA panel
resolution with frequency range from 25 MHz to 112 MHz, or DVI model at a pixel resolution
up to 1600 x 1200 at 85 Hz.
5.1.3 Display types
CRT and panel displays can be used simultaneously. The PCM-9587 can be set in one of six
configurations: CRT only, LVDS only, both CRT and LFP (LVDS), EFP (DVO to DVI), TV, both
CRT and EFP (DVO to DVI). The system is initially set to simultaneous display mode - CRT
and LFP (LDVS). If you want to enable other display mode, please set up manually. Set up
example is shown as in the following chapters.
5.1.4 Dual/Simultaneous Display
The PCM-9587 uses a Intel Montara-GM/GM+ GMCH Chrontel 7009 controller that is capa-
ble of providing simultaneous dual view display of the same content on a flat panel and CRT.
To set up dual view (simultaneous mode) under Windows NT/2000/XP, follow these steps:
1. Open the Control panel, and select “Display”.
2. Select “Settings”.
3. Select "Advanced", "Graphic Properties."
4. Select "Devices" mode and click "OK".
PCM-9587 User Manual
30
31
PCM-9587 User Manual
5.2 Installation of the PCI Graphic driver
Complete the following steps to install the PCI graphic driver. Follow the procedures in the
flow chart that apply to the operating system that you are using within your PCM-9587.
Note!
1. The windows illustrations in this chapter are intended as examples
only. Please follow the listed steps, and pay attention to the instruc-
tions which appear on your screen.
2. For convenience, the CD-ROM drive is designated as "D" through-
out this chapter.
5.2.1 Installation for Windows 2000/XP
To install PCI Graphic driver for Windows 2000/XP, please run the set up wizard "Intel
Extreme Graphic 2" in CD-ROM. Example of installation steps is shown as bellow:
PCM-9587 User Manual
32
33
PCM-9587 User Manual
6.1 Introduction
The PCM-9587's on-board audio interface provides high-quality stereo sound and
FM music synthesis (ESFM) by using the Intel 6300ESB audio controller. The audio
interface can record, compress, and play back voice, sound, and music with built-in
mixer control.
6.2 Driver installation
6.2.1 Before you begin
Please read the instructions in this chapter carefully before you attempt installation.
The audio drivers for the PCM-9587 board are located on the audio driver CD. Run
the supplied SETUP program to install the drivers; don’t copy the files manually.
Note!
1. Note1: Before trying to install the driver, go to Chapter 3 to use the
"Chipset Software Installation Utility " first.
2. The files on the software installation diskette are compressed. Do
not attempt to install the drivers by copying the files manually. You
must use the supplied SETUP program to install the drivers.
6.2.2 Windows 2000/XP drivers
1. To install Audio driver for Windows 2000/XP, please run the set up wizard
"Install Shield Wizard for Realtek AC'97 Audio" in CD-ROM. Example of
installation steps is shown as bellow.
PCM-9587 User Manual
36
2. In the Hardware Update Wizard window, click "Next".
37
PCM-9587 User Manual
3. In the following Hardware Update Wizard window, click "Finish" for Windows to
complete audio driver installation.
PCM-9587 User Manual
38
7.1 Introduction
The PCM-9587 is equipped with a high-performance 32-bit Ethernet chipset which is
fully compliant with IEEE 802.3 100 Mbps CSMA/CD standards. It is supported by
major network operating systems. It is also both 100Base-T and 10Base-T compati-
ble.
7.2 Features
„
Intel® 82551ER 10/100Base-T Ethernet LAN controller
„
Supports Wake-on-LAN remote control function.(Only support via Intel®
82551QM)
„
„
„
PCI Bus Master complies with PCI Rev. 2.2
Complies with 100Base-TX, and 10Base-T applications.
Single RJ-45 connector gives auto-detection of 10 Mbps or 100 Mbps network
data transfer rates and connected cable types.
„
„
„
Enhancements on ACPI & APM.
Complies with PCI Bus Power Management Interface Rev. 1.1,
ACPI Rev. 2.0, and Device Class Power Management Rev. 1.0.
7.3 Installation of Ethernet Driver
Before installing the Ethernet driver, note the procedures below. You must know
which operating system you are using in your PCM-9587, and then refer to the corre-
sponding installation procedure. Then just follow the steps described. You will quickly
and successfully complete the installation, even if you are not familiar with instruc-
tions for Windows.
Note!
The windows illustrations in this chapter are examples only. You must
follow the flow chart instructions and pay attention to the instructions
which then appear on your screen.
7.3.1 Installation for Windows 2000
1. a.Select "Start", "Settings". "Control Panel".
b. Double click "Network".
PCM-9587 User Manual
40
2. Click “Add new hardware wizard” and prepare to install networkfunction
41
PCM-9587 User Manual
3. Choose Hardware Device “Ethernet Controller”.
PCM-9587 User Manual
42
43
PCM-9587 User Manual
4. Insert the CD into D: drive
a. Fill in the Find the LAN chipset folder at the directory of PCM-9587 win2000
folder from CD ROM drive
b. Click “OK”.
5. Choose the "Intel(R) GD82559ER PCI Adapter" item. Click “Next”.
PCM-9587 User Manual
44
45
PCM-9587 User Manual
A.1 Supported GPIO Register
Below are detailed descriptions of the GPIO addresses and a programming sample.
A.1.1 GPIO Registers
CRF0 (GP10-GP17 I/O selection register. Default 0xFF)
When set to a '1', respective GPIO port is programmed as an input port.
When set to a '0', respective GPIO port is programmed as an output port.
CRF1 (GP10-GP17 data register. Default 0x00)
If a port is programmed to be an output port, then its respective bit can be read/writ-
ten.
If a port is programmed to be an input port, then its respective bit can only be read.
CRF2 (GP10-GP17 inversion register. Default 0x00)
When set to a '1', the incoming/outgoing port value is inverted.
When set to a '0', the incoming/outgoing port value is the same as in data register.
Extended Function Index Registers (EFIRs)
The EFIRs are write-only registers with port address 2Eh or 4Eh on PC/AT systems.
Extended Function Data Registers (EFDRs)
the EFDRs are read/write registers with port address 2Fh or 4Fh on PC/AT systems.
A.1.2 GPIO Example program-1
---------------------------------------------------------------------------------------------------------------
Enter the extended function mode, interruptible double-write
---------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,87H
OUT DX,AL
OUT DX,AL
---------------------------------------------------------------------------------------------------------------
Configured logical device 7 (GP10~GP17), configuration register CRF0,CRF1,CRF2
---------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,07H; point to Logical Device Number Reg.
OUT DX,AL
MOV DX,2FH
MOV AL,07H; select logical device 7
OUT DX,AL;
MOV DX,2EH
MOV AL,F0
OUT DX,AL
MOV DX,2FH
MOV AL,00H; 01:Input 00:output for GP10~GP17
OUT DX,AL
MOV DX,2EH
PCM-9587 User Manual
48
MOV AL,F2H;
OUT DX,AL
MOV DX,2FH
MOV AL,00H;Set GPIO is normal not inverter
OUT DX,AL;
MOV DX,2EH
MOV AL,F1H
OUT DX,AL
MOV DX,2FH
MOV AL,**H; Put the output value into AL **H
OUT DX,AL
---------------------------------------------------------------------------------------------------------------
Exit extended function mode |
---------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,AAH
OUT DX,AL
Note!
The input/output data (**) is a value of time interval. The value range is
from 01 (hex) to 3F (hex), and the related time interval is 1 sec. to 62
sec.
Data Time Interval
01
02
03
04
1 sec.
2 sec
3 sec
4 sec
49
PCM-9587 User Manual
A.2 Watchdog programming
Bellow is a sample of programming code for controlling the Watchdog Timer function.
---------------------------------------------------------------------------------------------------------------
Enter the extended function mode, interruptible double-write |
---------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,87H
OUT DX,AL
OUT DX,AL
---------------------------------------------------------------------------------------------------------------
Configured logical device 8, configuration register CRF6 |
---------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,07H; point to Logical Device Number Reg.
OUT DX,AL
MOV DX,2FH
MOV AL,08H; select logical device 8
OUT DX,AL;
MOV DX,2EH
MOV AL,30H;Set watch dog activate or inactivate
OUT DX,AL
MOV DX,2FH
MOV AL,01H; 01:activate 00:inactivate
OUT DX,AL;
MOV DX,2EH
MOV AL,F5H; Setting counter unit is second
OUT DX,AL
MOV DX,2FH
MOV AL,00H
OUT DX,AL;
MOV DX,2EH
MOV AL,F6H
OUT DX,AL
MOV DX,2FH
MOV AL,05H; Set 5 seconds
OUT DX,AL
;--------------------------------------------------------------------------------------------------------------
; Exit extended function mode |
;--------------------------------------------------------------------------------------------------------------
MOV DX,2EH
MOV AL,AAH
OUT DX,AL
PCM-9587 User Manual
50
B.1 LCD Backlight Connector (CN1)
Table B.1: LCD Backlight Connector (CN1)
Pin
Signal
1
2
3
4
5
+12 V
GND
LVDS_BKLTEN
VBR
+5 V
B.2 TV Out Connector (CN2) (TV out optional by
request)
Table B.2: TV Out Connector (CN2) (TV out optional by request)
Pin
Signal
1
2
3
4
5
Y
C
GND
GND
CVBS
B.3 CD-IN Connector (CN3)
Table B.3: CD-IN Connector (CN3)
Pin
Signal
1
2
3
4
CD_R
GND
GND
CD_L
PCM-9587 User Manual
52
B.4 Audio Output Connector (CN4)
Table B.4: Audio Output Connector (CN4)
Pin
Signal
Pin
Signal
1
SPK_R+
SPK_L+
LOUT_R
A_GND
LIN_R
2
SPK_R-
SPK_L-
LOUT_L
A_GND
LIN_L
3
4
5
6
7
8
9
10
12
14
16
11
13
15
A_GND
NC
A_GND
MIC_L
MIC_R
A_GND
B.5 Power input Connector (CN5)
Table B.5: Power input Connector (CN5)
Pin
Signal
Pin
Signal
1
GND
VCC
VCC
GND
VCC
VCC
2
GND
3
4
GND
5
6
5VSB
PSON#
GND
7
8
9
10
12
11
+12V
B.6 -12V and -5V Connector (CN6)
Table B.6: -12V and -5V Connector (CN6)
Pin
Signal
1
2
3
-5V
GND
-12V
53
PCM-9587 User Manual
B.7 VGA Connector (CN7)
Table B.7: VGA Connector (CN7)
Pin
Signal
Pin
Signal
1
VGA_R
VGA_G
VGA_B
NC
2
VGA_VCC
GND
3
4
5
6
NC
7
8
VGA_DATA
VGA_HS
VGA_VS
VGA_CLK
NC
9
GND
10
12
14
16
11
13
15
GND
GND
GND
B.8 LVDS Connector (CN8)
Table B.8: CN8 LVDS connector
Signal
VDD_FP
GND
Pin
1
Pin
Signal
VDD_FP
GND
2
3
4
VDD_FP
YAM0
YAP0
5
6
VDD_FP
YBM0
YBP0
GND
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
GND
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
YAM1
YAP1
YBM1
YBP1
GND
GND
YAM2
YAP2
YBM2
YBP2
GND
GND
CLKAM
CLKAP
GND
CLKBM
CLKBP
GND
DCLK
GND
DDAT
GND
YAM3
YAP3
YBM3
YBP3
NC
BKLTEN
PCM-9587 User Manual
54
B.9 DVI Connector (CN9)
Table B.9: DVI Connector (CN9)
Pin
Signal
Pin
Signal
1
C0#
C0
2
VCC_DVI
CK#
3
4
5
GND
C1#
C1
6
CK
7
8
GND
9
10
12
14
16
18
20
DVI_CLK
DVI_DATA
HP_DET
MI2C_DATA
MI2C_CLK
NC
11
13
15
17
19
GND
C2#
C2
VCC_DVI
NC
B.10 Gigabit LAN Connector (CN10 Optional)
Table B.10: Gigabit LAN Connector (CN10)
Pin
Signal
Pin
Signal
1
3
5
7
9
NC
2
NC
RJ45_7
RJ45_4
RJ45_3
RJ45_1
4
RJ45_8
RJ45_5
RJ45_6
RJ45_2
6
8
10
B.11 10/100M LAN Connector (CN11)
Table B.11: 10/100M LAN Connector (CN11)
Pin
Signal
1
2
3
4
5
6
7
8
9
10
VCC_LAN
ACTLED
RX+
RX-
LILED
GND
NC
GND
TX+
TX-
55
PCM-9587 User Manual
B.12 Gigabit LAN LED Connector (CN12 Optional)
Table B.12: Gigabit LAN LED Connector (CN12)
Pin
Signal
Pin
Signal
1
3
5
7
VCC_LAN25
LINK
2
4
6
8
GND
ACT
LINK100
NC
LINK1000
NC
B.13 System FAN Connector (CN13)
Table B.13: System FAN Connector (CN13)
Pin
Signal
1
2
3
GND
+12V
Detection
B.14 Floppy Disk Drive Connector (CN14)
3 1
4 2
33 31
34 32
Table B.14: Floppy Disk Drive Connector (CN14)
Pin
Signal
Pin
Signal
1
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
2
RWC#
NC
3
4
5
6
DS1
7
8
INDEX#
MOA#
DSB#
DSA#
MOB#
DIR#
9
10
12
14
16
18
20
22
24
26
28
30
32
34
11
13
15
17
19
21
23
25
27
29
31
33
STEP#
WD#
WE#
TRACK0#
WP#
RDATA#
HEAD
DSKCHG#
PCM-9587 User Manual
56
B.15 Primary HDD Connector (CN15)
Table B.15: Primary HDD Connector (CN15)
Pin
Signal
Pin
Signal
1
Reset
D7
2
GND
D8
1
3
2
4
3
4
5
D6
6
D9
7
D5
8
D10
9
D4
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
D11
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
D3
D12
D2
D13
D1
D14
D0
D15
GND
DREQ
DIOW
DIOR
IORDY
DACK
IDE IRQ14
ADDR 1
ADDR 0
CS1
KEY
GND
GND
GND
GND
GND
NC
66DET
ADDR 2
CS3
GND
37
39
38
40
DASP
B.16 Printer Port Connector (CN16)
Table B.16: Printer Port Connector (CN16)
Pin
Signal
Pin
Signal
1
STROBE*
D0
2
AUTOFD*
ERR
3
4
5
D1
6
INIT*
SLCTINI*
GND
7
D2
8
9
D3
10
12
14
16
18
20
22
24
26
11
D4
GND
13
D5
GND
15
D6
GND
17
D7
GND
19
ACK*
BUSY
PE
GND
21
GND
23
GND
25
SLCT
NC
* low active
57
PCM-9587 User Manual
B.17 USB Connector (CN18,20)
Table B.17: USB Connector (CN18,20)
Pin
Signal
Pin
Signal
1
3
5
7
9
+5 V
2
+5 V
UV0-/2-/4-
UV0+/2+/4+
GND
4
UV1-/3-/5-
UV1+/3+/5+
GND
6
8
GND
10
NC
B.18 DIO Connector (CN19)
Table B.18: DIO Connector (CN19)
Pin
1
Signal
DIO IN0
GND
Pin
2
Signal
DIO OUT0
GND
3
4
5
DIO IN1
VCC
6
DIO OUT1
NC
7
8
9
DIO IN2
GND
10
12
14
DIO OUT2
GND
11
13
DIO IN3
DIO OUT3
PCM-9587 User Manual
58
B.19 COM Port Connector (CN21)
Table B.19: COM Port Connector (CN21)
Pin
1
Signal
Pin
2
Signal
COM1 DCD
COM1 RX
COM1 DSR
COM1 RTS
COM1 CTS
COM1 RI
GND
3
4
5
COM1 TX
6
7
COM1 DTR
GND
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
COM2 DCD/485TX-
COM2 RX /485TX+
COM2 TX /485RX+
COM2 DTR/485RX-
GND
COM2 DSR
COM2 RTS
COM2 CTS
COM2 RI
GND
COM3 DCD
COM3 RX
COM3 DSR
COM3 RTS
COM3 CTS
COM3 RI
GND
COM3 TX
COM3 DTR
GND
COM4 DCD
COM4 RX
COM4 DSR
COM4 RTS
COM4 CTS
COM4 RI
GND
COM4 TX
COM4 DTR
GND
59
PCM-9587 User Manual
B.20 Front Panel Connector (CN22)
Table B.20: Front panel Connector (CN22)
Pin
Signal
Pin
Signal
1
HDD LED+
Power LED+
Suspend LED
LAN ACT+
LAN Link+
VCC_DUAL
GND
2
HDD LED-
GND
3
4
5
6
GND
7
8
LAN ACT-
LAN Link-
ATX Power Button
Reset
9
10
12
14
11
13
B.21 SATA Connector 1 (CN23)
Table B.21: SATA Connector 1 (CN23)
Pin
Signal
1
2
3
4
5
6
7
GND
TX0
TX0#
GND
RX0#
RX0
GND
PCM-9587 User Manual
60
B.22 SATA Connector 2 (CN24)
Table B.22: SATA Connector 2 (CN24)
Pin
Signal
1
2
3
4
5
6
7
GND
TX1
TX1#
GND
RX1#
RX1
GND
B.23 CPU FAN Connector (CN25)
Table B.23: CPU FAN Connector (CN25)
Pin
Signal
1
2
3
GND
+12V
SPEED DETECT
B.24 Extension SMBUS Connector (CN26)
Table B.24: Extension SMBUS Connector(CN26)
Pin
Signal
1
2
3
4
GND
SMBDATA
SMBCLK
3VSB
61
PCM-9587 User Manual
B.25 Keyboard and PS/2 Mouse Connector (CN27)
Table B.25: Keyboard and Mouse Connector (CN27)
Pin
Signal
1
2
3
4
5
6
KB CLOCK
KB DATA
MS CLOCK
GND
+5V
MS DATA
B.26 CPU FAN Connector (wafer
box)(Optional)(CN28)
Table B.26: CPU FAN Connector (wafer box)(Optional)(CN28)
Pin
Signal
1
2
3
Detection
VCC 5V
GND
PCM-9587 User Manual
62
B.27 Mini PCI Connector(CN29)
Table B.27: Mini PCI Connector (CN29)
Pin
Signal
Pin
Signal
1
TIP Key
2
RING Key
8PMJ-13, 4
8PMJ-23, 4
8PMJ-43, 4
8PMJ-53, 4
LED2_YELP
LED2_YELN
RESERVED
5V
3
8PMJ-33, 4
8PMJ-63, 4
8PMJ-73, 4
8PMJ-83, 4
LED1_GRNP
LED1_GRNN
CHSGND
INTB#
4
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
11
13
15
17
19
21
23
25
27
3.3V
INTA#
RESERVED
GROUND
CLK
RESERVED
3.3VAUX
RST#
GROUND
3.3V
B.28 CompactFlash Card Connector (CN30)
Table B.28: CompactFlash Card Connector (CN30)
Pin
Signal
Pin
Signal
1
GND
2
SDD3
SDD5
SDD7
GND
3
SDD4
SDD6
SDCS#1
GND
4
5
6
7
8
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
GND
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
GND
GND
+5V
GND
GND
GND
GND
SDA2
SDA0
SDD1
NC
SDA1
SDD0
SDD2
NC
NC
SDD11
SDD13
SDD15
NC
SDD12
SDD14
SDCS#3
SDIOR
+5V
SDIOW
IRQ15
CSEL
IDERST
NC
+5V
NC
SDIORDY
+5V
SDDASP
SDD8
SDD10
S66DET
SDD9
GND
63
PCM-9587 User Manual
PCM-9587 User Manual
64
C.1 System I/O Ports
Table C.1: System I/O Ports
Addr. range (Hex)
Device
000-01F
020-021
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0
DMA controller
Interrupt controller 1, master
8254 timer
8042 (keyboard controller)
Real-time clock, non-maskable interrupt (NMI) mask
DMA page register
Interrupt controller 2
DMA controller
Clear math co-processor
Reset math co-processor
Math co-processor
0F1
0F8-0FF
1F0-1F8
170- 178
200-207
278-27F
2E8-2EF
2F8-2FF
300-31F
360-36F
378-37F
380-38F
3A0-3AF
3B0-3BF
3C0-3CF
3D0-3DF
3E8-3EF
3F0-3F7
3F8-3FF
Fixed disk
Fixed disk (2nd IDE)
Reserved (Game I/O)
Parallel printer port 2 (LPT 3)
Series port 4
Serial port 2
Prototype card
Reserved
Parallel printer port 1 (LPT 2)
SDLC, bisynchronous 2
Bisynchronous 1
Monochrome display and printer adapter (LPT1)
Reserved
Color/graphics monitor adapter
Series port 3
Diskette controller
Serial port 1
* PNP audio I/O map range from 220 ~ 250H (16 bytes)
MPU-401 select from 300 ~ 330H (2 bytes)
PCM-9587 User Manual
66
C.2 1st MB memory map
Table C.2: 1st MB memory map
Addr. range (Hex)
Device
F0000h - FFFFFh
*CC000h - EFFFFh
C0000h - CBFFFh
B8000h - BFFFFh
B0000h - B7FFFh
A0000h - AFFFFh
00000h - 9FFFFh
System ROM
Unused (reserved for Ethernet ROM)
Expansion ROM (for VGA BIOS)
CGA/EGA/VGA text
Unused
EGA/VGA graphics
Base memory
* If Ethernet boot ROM is disabled (Ethernet ROM occupies about 16 KB)
* E0000 - EFFFF is reserved for BIOS POST
C.3 DMA channel assignments
Table C.3: DMA channel assignments
Channel
Function
0
1
2
3
4
5
6
7
Available
Reserved (audio)
Floppy disk (8-bit transfer)
Available (parallel port)
Cascade for DMA controller 1
Available
Available
Available
* Audio DMA select 1, 3, or 5
** Parallel port DMA select 1 (LPT2) or 3 (LPT1)
67
PCM-9587 User Manual
C.4 Interrupt assignments
Table C.4: Interrupt assignments
Interrupt#
Interrupt source
IRQ 0
IRQ 1
IRQ 2
IRQ 3
IRQ 4
IRQ 5
IRQ 6
IRQ 7
IRQ 8
IRQ 9
IRQ 10
IRQ 11
IRQ 12
IRQ 13
IRQ 14
IRQ 15
Interval timer
Keyboard
Interrupt from controller 2 (cascade)
COM2
COM1
COM4
FDD
LPT1
RTC
Reserved (audio)
COM3
Reserved for watchdog timer
PS/2 mouse
INT from co-processor
Primary IDE
Secondary IDE for CFC
* Ethernet interface IRQ select: 9, 11, 15
* PNP audio IRQ select: 9, 11, 15
* PNP USB IRQ select: 9, 11, 15
* PNP ACPI IRQ select: 9, 11, 15
PCM-9587 User Manual
68
The PCM-9587 requires several cables for normal operation. You can make them
yourself or purchase an optional cable kit assembly, which includes the following
D.1 PCM-10586-6200E Cable kit for PCM-9587
Table D.1: PCM-10586-6200E wiring kit 9587
PCM-9587F
Connector
Part No.
Cable Description
Terminating Connector
Dual floppy, 3.5" and
5.25" (34p)
1701340603
1700260250
1700001296
CN14
CN16
CN7
34-pin dual floppy
Parallel Port
26pin,female DSUB
2 x 8-pin header (2 mm) 15-pin
DSUB
VGA CRT
1703060191
1701400181
KB/mouse cable
COM 1-4 cable
CN27
CN21
6-pin circular DIN
40-pin, 9-pin male DSUB x 4
F3.5 mm 16-pin, 5 female phone
jacks
1700160160
1701400452
1703100260
Audio cable
CN4
40-pin, 2.54 mm, female IDC
(450 mm)
3.5" IDE DMA/66 (40p) CN15
10-pin, IDE 2.0 mm, USB x 2 (26
cm)
USB cable
CN20
1700071000
1703050106
1700000410
1701100202
SATA cable
TV-out cable
TMDS cable
CN23
CN2
CN9
7P/7P 100CM
Wire 10 cm 5P TV-out
Cable DVI- 26P/DF13-20P 20 cm
RJ45 8-pin modular
Network, 10/100 Base-T CN11
PCM-9587 User Manual
70
|