Acer G195HQ User Manual

Acer G195HQ

Service Guide

Transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in

any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without

the prior written permission of Acer Incorporated.

Disclaimer

The information in this guide is subject to change without notice. Acer Incorporated makes no representations or

warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties

of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is

sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer

Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any

incidental or consequential damages resulting from any defect in the software.

Intel is a registered trademark of Intel Corporation.

Pentium and Pentium II/III are trademarks of Intel Corporation.

Other brand and product names are trademarks and/or registered trademarks of their respective holders.

Trademarks

Acer is a registered trademark of Acer Incorporated.

All other trademarks are property of their respective owners.

Conventions

The following conventions are used in this manual:

Screen messages

Note

Denotes actual messages that appear on screen.

Gives bits and pieces of additional information related to the current topic.

Alerts you to any damage that might result from doing or not doing specific actions.

Gives precautionary measures to avoid possible hardware or software problems.

Remind you to do specific actions relevant to the accomplishment of procedures.

Warning

Caution

Important

Preface

Before using this information and the product it supports, please read the following general information.

1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided

for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness,

your regional office may have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra

memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such

cases, please contact your regional offices or the responsible personnel/channel to provide you with further

technical details.

2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on

your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the

printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a

DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list

provided by your regional Acer office to order FRU parts for repair and service of customer machines.

Warning: (For FCC Certified Models)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this

equipment. It is the responsibility of the user to correct such interference.

As ENERGY STAR^®Partner our company has determined that this product meets the ENERGY STAR^®

guidelines for energy efficiency.

Warning:

To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerous high voltages are present

inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

Precautions

z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in

a wet basement.

z Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and

cause serious damage to the appliance. Use only a trolley or stand recommended by the manufacturer or sold

with the monitor. If you mount the monitor on a wall or shelf, uses a mounting kit approved by the manufacturer

and follow the kit instructions.

z Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable

operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered.

Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator

or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

z The monitor should be operated only from the type of power source indicated on the label. If you are not sure of

the type of power supplied to your home, consult your dealer or local power company.

z The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit

only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,

have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the

safety purpose of the grounded plug.

Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the

monitor from damage due to power surges.

z Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

z Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric

shock. Never spill liquids on the monitor.

z Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous

voltages and other hazards. Please refer all servicing to qualified service personnel

z To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate

configured receptacles marked between 100 - 240V AC, Min. 5A.

z The wall socket shall be installed near the equipment and shall be easily accessible.

Special Notes on LCD Monitors

The following symptoms are normal with LCD monitor and do not indicate a problem.

Notes

z Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and

then turn it on again to make sure the flicker disappears.

z You may find slightly uneven brightness on the screen depending on the desktop pattern you use.

z The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a

missing pixel or a pixel lit all of the time.

z Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image,

when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image

or turning off the Power Switch for hours.

Table of Contents

Chapter 1

Monitor Features

…………………………………………

Introduction

………………………………………

Electrical Requirements

LCD Monitor General Specification

LCD Panel Specification

Factory Preset Timing

Monitor Block Diagram

Main Board Diagram

Power Board Diagram

Software Flow chart

Main Board Layout

………………………………………

Installation

Chapter 2

Operating Instructions

………………………………………

User Controls

………………………………………

Front Panel Controls

eColor Management (OSD)

How to Adjust a Setting

How to Optimize The DOS-Mode

Enter into the factory mode

Chapter 3

Machine Disassembly

………………………………………

Chapter 4

Chapter 5

Troubleshooting

………………………………………

Connector Information

Chapter 6

Chapter 7

FRU (Field Replacement Unit) List

………………………………………

Exploded Diagram

………………………………………

Schematic Diagram

………………………………………

Monitor Features

Chapter 1

Introduction

Scope

This short specification describes the electrical, optical and functional performance requirements for a 47cm (18.5”)

TFT LCD color monitor with VGA&DVI compatible interface.

Description

The LCD monitor is designed with the latest LCD technology to provide a performance oriented product with no

radiation. This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop

space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF

target is 50k hours or more.

Chart of G195HQ

Panel

M185XW01

D-Sub 15pin;

DVI 24pin(Dual-Input Model);

Signal Interface

Sync Type

Separate / Compatible

Support

Color Temp User Adjust

DDC

DDC2B

Speaker

Option

Headphone Jack

Microphone Jack

USB Hub

Option

Tilt / Swivel

Yes /No

Electrical Requirements of G195HQ

Standard Test Conditions

All tests shall be performed under the following conditions, unless otherwise specified.

Warm up time

AC supply voltage

Ambient temperature

Humidity

＞ 30 min.

220V± 5％, 50± 3 Hz

20°C ± 5°C

50% ± 10%

Display mode

e-color mode

1366 x 768, 60 Hz, all white

Set to “User” mode

Set to The value under user mode, which allows that the brightest

two of 32 linear distributed gray-scales (0～ 700mv) can be

distinguished.

Contrast control

Color temperature

Brightness control

Analog Input signal

Picture position and size

Viewing angle

6500°K

The value under user mode

700 mVss

Factory preset value,

90 ° H and V

Viewing distance

40 cm for LCD performance, 20 cm for LCD failures

Dark room < 1 cd/m2

Ambient illumination

Measurement systems

The units of measure stated in this document are listed below:

1 gamma = 1 nano tesla

1 tesla = 10,000 gauss

cm = in x 2.54

Lb = kg x 2.2

Degrees F = [°C x 1.8] + 32

Degrees C = [°F - 32]/1.8

u' = 4x/(-2x + 12y + 3)

v' = 9y/(-2x + 12y + 3)

x = (27u'/4)/[(9u'/2) - 12v' + 9]

y = (3v')/[(9u'/2) - 12v' + 9]

nits = cd/(m2) = Ft-L x 3.426

lux = foot-candle x 10.76

LCD Monitor General Specification

Driving system

Pixel pitch

TFT Color LCD

0.3(H) x 0.3(V)

1000 : 1 (typ)

5ms(Typ.). 8ms(max)

250 cd/m²(Typ.)

H/V TTL

Contrast Ratio

Response time

Luminance of White

Separate Sync.

H-Frequency

LCD Panel

Input

30kHz – 80kHz

55-75Hz

V-Frequency

Viewing angle

H:170°/ V:160° ( type)(CR>10)

Display Colors

16.7M

Weight(with stand)

Weight(without stand)

Dimension(with stand)

3.7KG

3.36KG

452.59(H)x 348.90(V) x 173.80(D) (mm)

Dimension(without stand) 452.59(H)x 288.95(V) x 60.00(D) (mm)

Display mode

1366 x 768 @60Hz

ON Mode

< 37W

< 1W

EPA ENERGY STAR®

OFF Mode

Set to The value under user mode, which allows that the brightest two of 32 linear

distributed gray-scales (0～ 700mv) can be distinguished.

Contrast control

Power Source

100 V ~ 240 V，50 ± 3Hz, 60 ± 3Hz

Operating Temp: 0° to 40°C

Storage Temp: -20° to 60°C

Operating Humidity: 15% to 90%

Storage Humidity: 15% to 90%

Operating Altitude: 12,000 feet

Storage Altitude: 40,000 feet

Environmental

Considerations

Peak surge current

Power line surge

< 55A peak at 240 VAC and cold starting

No advance effects (no loss of information or defect)

60.00 mm

452.59 mm

G195HQ

173.80 mm

261.18 mm

LCD Panel Specification of G195HQ

This specification applies to the 18.5 inch-wide Color a-Si TFT-LCD Module M185XW01.The display supports the

WXGA - 1366(H) x 768(V) screen format and 16.7M colors (RGB 6-bits +Hi-FRC data). All input signals are

1-channel LVDS interface and this module doesn’t contain an inverter board for backlight.

General Specifications

Block Diagram

TFT LCD Module

Optical Specifications

Factory Preset Timing of G195HQ

Monitor Block Diagram

The LCD MONITOR will contain a main board, a power board, and a key board which house the flat panel control

logic, brightness control logic and DDC.

The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips

each voltage.

Flat Panel and

CCFL backlight

CCFL Drive.

Main Board

Power Board

AC-IN

100V-240V

Key board

DVI Signal

D-SUB Signal

(Dual-Input model)

Main Board Diagram

T89AM6D8MXAFH2 (Dual-Input Model)

Crystal 14.31818MHZ

(X401)

Panel Interface

(CN301)

Scalar IC TSUMU5PEHL-LF

Flash Memory

EN25F20

(U402)

Key control Interface

(CN402)

(Include MCU, ADC, OSD)

(U401)

H sync

V sync

RGB

D-Data

D-Clock

D-Sub

Connector

(CN101)

DVI

Connector

(CN102)

T89AM5D8MXAFN2

Crystal 14.31818MHZ

(X401)

Panel Interface

(CN301)

Scalar IC TSUM1PEL

Flash Memory

EN25F20

(U402)

Key control Interface

(CN402)

(Include MCU, ADC, OSD)

(U401)

H sync

V sync

RGB

D-Sub

Connector

(CN101)

Power Board Diagram

14.5V

AC input

EMI filter

Bridge

Rectifier

and Filter

Rectifier

diodes

Transformer

Start Resistor

(R908)

Feedback

Circuit

PWM Control

(U901)

Power Switch

(Q901)

Photo coupler

(U902)

Output

Transformer

(T801)

MOSFET

(Q803)

14.5V

Circuit

Lamp

PWM Control

AM9000ES

(U801)

Feedback

Circuit

ON/OFF

DIM

Software Flow Chart

Remark:

1) MCU initializes.

2) Is the EEPROM blank?

3) Program the EEPROM by default values.

4) Get the PWM value of brightness from EEPROM.

5) Is the power key pressed?

6) Clear all global flags.

7) Are the AUTO and SELECT keys pressed?

8) Enter factory mode.

9) Save the power key status into EEPROM.

Turn on the LED and set it to green color.

Scalar initializes.

10) In standby mode?

11) Update the lifetime of back light.

12) Check the analog port, are there any signals coming?

13) Does the scalar send out an interrupt request?

14) Wake up the scalar.

15) Are there any signals coming from analog port?

16) Display "No connection Check Signal Cable" message. And go into standby mode after the

message disappears.

17) Program the scalar to be able to show the coming mode.

18) Process the OSD display.

19) Read the keyboard. Is the power key pressed?

Main Board Layout

715G2883 1 6

Symbol Description

TSUM1PEL PQFP-100

U401

TSUMU5PEHL-LF

CN302 WAFER

PQFP-100(Dual-Input Model)

U701

U106

U103

AP1117E33L-13

CN701 CONNECTOR 9P 2.0

AZC099-04S SOT23-6L

CN402 CONN 6PIN 2.0

CN101 D-SUB 15PIN VERTICAL CONN WITH SCREW

DVI 24PIN CONN F ATTACHED

CN102

U402

U104

X401

U106

EN25F20-100GCP 2Mb SOP-8

AZC099-04S SOT23-6L

SCREW(Dual-Input Model)

U105

U107

AZC099-04S SOT23-6L(Dual-Input Model)

14.31818MHZ/32PF/49US

AZC099-04S SOT23-6L(Dual-Input

Model)

Installation

To install the monitor to your host system, please follow the steps as given below:

Steps

1. 1-1 Connect Video Cable

a. Make sure both the monitor and computer are powered-OFF.

b. Connect the VGA video cable to the computer.

1-2 Digital Cable (Only Dual-Input Model)

a. Make sure both the monitor and computer are powered-OFF.

b. Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the

computer’s port.

1-3 Connect one end of the 19-pin HDMI cable to the back of the monitor and connect the other end to the

computer’s port(Optional).

2. Connect the Audio Cable (Only Audio-Input Model)(Optional)

3. Connect power cord

Connect the power cord to the monitor, then to a properly grounded AC outlet.

4. Power-ON Monitor and Computer

Power-ON the monitor first, then power-ON the computer. This sequence is very important.

5. If the monitor still does not function properly, please refer to the troubleshooting section to diagnose the problem.

Attaching / Removing the Base

Attaching:

Align the base with the stand and push the base towards the top of the monitor.

Removing:

Depress the release hooks as indicated first before removing the base and follow the arrow direction to remove it.

Screen Position Adjustment

To optimize the viewing position, you can adjust the monitor tilt by using both of your hands to hold the edges of the

monitor as shown below. The monitor can be adjusted to 15 degrees up or 5 degrees down.

Chapter 2

Operating Instructions

Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the

monitor. By changing these settings, the picture can be adjusted to your personal preferences.

• The power cord should be connected.

• Connect the video cable from the monitor to the video card.

• Press the power button to turn on the monitor position. The power indicator will light up.

User Controls

Power Switch / Power LED:

To turn the monitor ON or OFF.

Lights up to indicate the power is turned ON.

Using the Shortcut Menu

Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly

accessed settings.

Empowering:

Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes.

AUTO Auto Adjust:

Press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos,

VPos, Clock and Focus.

MENU OSD functions

Press this button to activate the OSD menu.

Volume Up / Down

Press to adjust volume (Only Audio-Input Model)(Optional)

INPUT Input Key

Use Input key to select from different video sources that may be connected to your monitor.

(a) VGA input (b) DVI input (c) HDMI input

As you cycle through the sources you will see the following messages on right top side of screen to indicate

currently selected input source. It may take 1 or 2 seconds for the image to appear.

VGA or DVI or HDMI

If either VGA or DVI input is selected ,but the VGA and DVI cables are not connected, a floating dialog box indicates:

“No Cable Connect” or “No Signal”

eColor Management (OSD)

Operation instructions

Step 1: Press “

Step 2: Press “

”Key to open the Acer eColor Management OSD and access the scenario modes

” or “ ” to select the mode

Step 3: Press “ AUTO “ Key to confirm the mode and exit the eColor menu.

Features and Benefits

Adjusting the OSD settings

The OSD can be used for adjusting the settings of your LCD Monitor.Press the MENU key to open the OSD. You

can use the OSD to adjust the picture quality, OSD position and general settings. For advanced settings,please refer

to following page:

Adjusting the picture quality

1 Press the MENU key to bring up the OSD.

2 Using the

3 Use the

keys, select

Picture from the OSD. Then navigate to the picture element you wish to adjust.

/ keys to adjust the sliding scales.

4 The Picture menu can be used to adjust the current Brightness, Contrast,Colour Temp, Auto Config and other

image-related qualities.

Adjusting the OSD position

1 Press the MENU key to bring up the OSD.

2 Using the directional

adjust.

keys, select OSD from the on screen display.Then navigate to the feature you wish to

Adjusting the setting

1 Press the MENU key to bring up the OSD.

2 Using the

keys, select

Setting from the OSD. Then navigate to the feature you wish to adjust.

3 The Setting menu can be used to adjust the screen Menu Language and other important settings.

Product information

1 Press the MENU key to bring up the OSD.

2 Using the

keys, select

Information from the OSD. Then the basic information of LCD monitor will show

up for current input.

How to Optimize The DOS-Mode

Plug And Play

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the

monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional

information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over

the DDC2B channel.

This monitor will appear to be non-functional if there is no video input signal. In order for this monitor to

operate properly, there must be a video input signal.

This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA)

and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees

(NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no

video-input signal present. When there is no video input signals this monitor, following a time-out period, will

automatically switch to an OFF mode. This reduces the monitor's internal power supply consumption. After the video

input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to

a "Screen Saver" feature except the display is completely off. Pressing a key on the keyboard, or clicking the mouse

restores the display.

Using the Right Power Cord

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed

and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.

Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of

a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type

attachment plug, rated 10A, 250V, and CEE-22 male configuration. The other end terminates with a molded-on type

connector body, rated 10A, 250V, having standard CEE-22 female configuration.

Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

Enter into the factory mode:

Turn off the power, press the “e-color” and turn the power on. The factory OSD will be at the left top of the panel.

Chapter 3

Machine Disassembly

This chapter contains step-by-step procedures on how to disassemble the monitor-

G195HQ for maintenance.

The tool for disassembly is as follows:

Screwdriver, Hexagonal screwdriver, Putty knife.

Disassembly Procedure

1.Lay the monitor on a flat, soft and clean surface.

2.Press the button remarked in green the remove the base.

3. Remove the two piece of cover hinge and the four screws remarked in red to remove the hinge assembly.

4.Remove the rear cover.

Pry the monitor up then find out the hooks’ position, use the tool (like the picture or other card) to insert into the

gap of bezel and rear cover.

Turn over the monitor and take off the rear cover.

4. Remove the bezel.

Disconnect the connector remarked in green.

PS: be careful to Disconnect the Key board connector, because the keyboard connector maybe damage.

The cable connect

the main board and

key board

Remove the 2 screws remarked in red.

Remove the lamp connectors to remove the panel. Put attention to the LVDS cable.

LVDS CABLE

6. Turn over the main frame and remove the four screws remarked in red and disconnected remarked in green to

remove the main board and power board.

Power board

Main board

Remove the speakers.(Optional)

7.The panel

Chapter 4

Troubleshooting

This chapter provides troubleshooting information for the G195HQ:

1.Main Board

1) No Power

No power

Press power key and look if the

picture is normal

Please reinsert and make sure the

AC of 100-240 is normal

Reinsert or check the

power section

Measure U701 Pin2=3.3V, C704 (+) =1.8V

Check U701, Q702 and Q703

Check if X401 oscillate waveforms are

normal

Replace X401

Replace U401

2) No Picture (LED is orange)

No picture

The button if under

control

X401 oscillate

waveform is normal

Replace X401

Check reset circuit of

U401 is normal

Check Correspondent

component

Measure U701 Pin2=3.3V,

C704(+)=1.8V

Replace U401

X401 oscillate

waveform is normal

Check U701, Q702 and Q703

Replace X401

Check HS/VS from

CN101 is normal

Check Correspondent

component

Replace U401

3) Panel Power Circuit

White screen

Measure Q302 base

is low level?

X401 oscillate

waveform is normal

Replace X401

Check CN301 is solder

and Q302, Q301 is OK?

Check reset circuit of

U401 is normal

Check Correspondent

component.

Check Correspondent

component.

Replace U401

Replace PANEL

2. Key Board

OSD is unstable or not working

Connect Key Board

Replace Button Switch

Replace Key Board

Is Key Pad Board connecting normally?

Is Button Switch normally?

Is Key Pad Board normally?

Check Main Board

3. Power Board

1) No power

Check CN902 PIN6, 7 = 5V

Check AC line volt 110V or 220V

Check AC input

Check the voltage of C907 (+)

Check bridge rectified circuit and F902 circuit

Check start voltage for the pin8 of U901

Check R908 and Change U901

Check the auxiliary voltage is bigger than

11V and smaller than 25V

1) Check U901

2) Check D907/Q901 circuit

Check U901 pin5 PWM wave

Check U901

Check D902/ Q906/Q904/U902/ZD901/U903

2.) No Backlight

Check C811(+)=14.5V

Check adapter or MB

Check Interface board

Check ON/OFF signal

Check U801 PIN11,14 have the output of square wave at short time

Change U801

Check Q803 PIN5, 6, 7, 8 have the output of square wave at short time.

Check Q803

Check the output of T801

Change T801

Check connecter & lamp

Chapter 5

Connector Information

D-sub connect and DVI connect:

15-Pin Color Display Signal Cable

24-Pin Color Display Signal Cable (Dual-Input Model)

Chapter 6

FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of G195HQ. Refer to this

chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).

NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information

available on your regional web or channel (http://aicsl.acer.com.tw/spl/). For whatever reasons a part number

change is made, it will not be noted in the printed Service Guide. For ACER AUTHORIZED SERVICE

PROVIDERS, your Acer office may have a DIFFERENT part number code from those given in the FRU list of

this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order

FRU parts for repair and service of customer machines.

NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on

how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

Exploded Diagram (Model: G195HQ)

Item Description

TPV Part No.

A34G1522AEMA1B0130

A33G0779AEM 1L0100

A33G0780AEM 1L0100

Acer Part No.

60.LJM0B.001

Q`ty

BEZEL L185WA-9acer5

KEY BUTTON

POWER BUTTON

LENS

N/A

A33G0768 1 1C0100

A15G0933101401

60.LJM0B.008

MAINFRAME

A15G0933101301 (Dual-Input

Model)

A34G1523AEM 4B0100

60.LJM0B.009 (Dual-Input Model)

60.LJM0B.002

REAR COVER

L205WA-9ACER5-S5

A34G1523AEM 3B0100

(Dual-Input Model)

60.LJM0B.003 (Dual-Input Model)

HINGE

A37G0137

60.LJM0B.004

60.LJM0B.005

60.LJM0B.006

60.LJO0B.004

60.LJM0B.007

N/A

STAND FRONT

STAND REAR

HINGE COVER

BASE

A34G1524AEM 1B0100

A34G1525AEM 1B0100

A33G0772AEM 1L0100

A34G1521AEM 1B0100

A15G0932101

BRAKET BASE

RUBBER

Q12G6300 95

N/A

POWER BOARD

PWPC9821AQMY

55.LJM0B.003

756GQ9CB BA256 00

55.LJM0B.001

MAIN BOARD

756GQ9CB BA255 00

(Dual-Input Model)

55.LJM0B.002 (Dual-Input Model)

KEY BOARD

KEPC9QKO

55.LJO0B.002

N/A

SCREW(FOR PB/MAIN

FRAME)

0G1G1130 8120

SCREW,(FOR MB/MAIN

FRAME)

SCREW(FOR

0G1G1130 8120

0Q1G1740 12120

N/A

HINGE/REAR COVER)

S4 SCREW

0M1G 140 6125

0Q1G 130 6120

N/A

S5 SCREW (T3X6)

Part List

Above picture show the description of the following component.

Picture

Description

TPV Part No.

Acer Part No.

60.LJM0B.008

A15G0933101401

60.LJM0B.009

(Dual-Input

Model)

Main_frame

A15G0933101301

(Dual-Input Model)

Bezel

A34G1522AEMA1B0130

60.LJM0B.001

Panel

750GLU185X1414N000

LK.18005.016

60.LJM0B.002

A34G1523AEM 4B0100

60.LJM0B.003

(Dual-Input

Model)

Rear Cover

A34G1523AEM 3B0100

(Dual-Input Model)

Power Board PWPC9821AQMY

55.LJM0B.003

756GQ9CB BA256 00

55.LJM0B.001

55.LJM0B.002

(Dual-Input

Model)

Main Board

756GQ9CB BA255 00

(Dual-Input Model)

Key Board

KEPC9QKO

55.LJO0B.002

60.LJM0B.004

Hinge

A37G0137

60.LJM0B.007

Base

A34G1521AEM 1B0100

Bracket Base A15G0932101

N/A

LVDS ASS'Y 095G8018 3XH60

50.LEF0B.002

D-SUB Cable 089G 728CAA DB

50.LAL0B.002

50.LAN0B.003

50.LBT0B.004

DVI Cable

(Dual-Input

Model)

089G1748HAAAC

Power Cord

089G404A18N CX

Chapter 7

Schematic Diagram

Main Board

T89AM6D8MXAFH2 (Dual-Input Model)

FB102

BEAD

MVCC_1

VGA_B+

VGA_B-

VGA_G+

VGA_G-

VGA_R+

VGA_R-

DVI_5V

R105

100R 1/16W 5% C102

0.047uF

DSUB_B+

DSUB_B-

H_Sy nc R102

V_Sy nc

0R05 1/10W 5%

R103 1K 1/16W 5%

R104 1K 1/16W 5%

R108

C105

5pF/50V

DSUB_H

DSUB_V

D109

75R 1/16W 5%

R106

R107

C103 C104

22pF

BAT54C

R109

100R 1/16WC51%06

0.047uF

2K2 1/16W 5%

22pF

U104

ESD_VCC

R110

470R 1/16W 5% C107

1000pF

DSUB_5V

DSUB_SOG

DSUB_G+

DSUB_SCL

DSUB_SDA

H_Sync

V_Sy nc

FB103

BEAD

I/O1 I/O4

GNDVDD

I/O2 I/O3

CN101

R111

100R 1/16W 5% C108

0.047uF

FB107

R101

AZC099-04S

C112

R112

C109

5pF/50V

DDC1_SCL

DSUB_SCL 15

VGA_PLUG

DSUB_5V

DDC1_SCL

DDC1_SDA

300 OHM

75R 1/16W 5%

100R 1/16W 5%

候綼　U103

VGA_B-

C124

0.1uF 16V

R114

100R 1/16W 5% C110

0.047uF

DSUB_G-

DSUB_R+

DSUB_SDA 12

VGA_B+

VGA_G-

VGA_G+

VGA_R-

VGA_R+

ZD104

RLZ5.6B

R113

ZD105

RLZ5.6B

VGA_G+

DDC1_SDA

100R 1/16W 5%

U103

ESD_VCC

FB101

BEAD

I/O1 I/O4

GNDVDD

I/O2 I/O3

DB15

VGA_R+

VGA_B+

R115

100R 1/16W 5%

C111

0.047uF

AZC099-04S

C101

R116

C113

5pF/50V

75R 1/16W 5%

候綼　U101

R117

100R 1/16W 5%C114

0.047uF

CMVCC

DSUB_R-

DSUB_5V

CN102

DVI_5V

D104

VSYNC

BAT54C

15 DVI_HPD

SYNC GND

DDC SCL

DDC SDA

+5V

R118 100R 1/16W 5% DDC2_SCL

R119 100R 1/16W 5% DDC2_SDA

DDC2_SCL

DDC2_SDA

R120 10K 1/16W 5%

R140

HPD

R123

R125

4K7 1/16W 5%

C116

C115

R121

1/3shield

2/4shield

0/5shield

clk shield

R122

HDCP_CTRL

R124

4K7 1/16W 5%

U101

0.1uF/16V

Q101

VCC A0

WP A1

SCL A2

SDA VSS

R126

R127

R128

R129

R130

R131

10R 1/16W 5% RX0P

10R 1/16W 5% RX0N

10R 1/16W 5% RX1P

10R 1/16W 5% RX1N

10R 1/16W 5% RX2P

10R 1/16W 5% RX2N

DDC1_SCL

DDC1_SDA

RX0P

RX0N

RX1P

RX1N

RX2P

RX2N

DAT0+

DAT0-

DAT1+

DAT1-

DAT2+

DAT2-

DAT3+

DAT3-

DAT4+

DAT4-

DAT5+

DAT5-

clk+

DDC_WP

NC / M24C02-WMN6TP

DVI_5V

FB105

CMVCC

FB104

300 OHM

C121

1000pF

300 OHM

D108

BAT54C

C122

R132

R134

10R 1/16W 5% RXCP

10R 1/16W 5% RXCN

RXCP

RXCN

1000pF

VCC3.3

clk-

JACK

U107

AZC099-04S

ESD_VCC2

U105

AZC099-04S

ESD_VCC1

U106

AZC099-04S

ESD_VCC1

ESD_VCC

FB108

R133

10K 1/16W 5%

C117

I/O1 I/O4

GNDVDD

I/O2 I/O3

I/O1 I/O4

GNDVDD

I/O2 I/O3

R136

GNDVDD

300 OHM

R137

R138

4K7 1/16W 5%

I/O2 I/O3

U102

DVI_HPD R135

VGA_PLUGR139

10K 1/16W 5%

6K8 1/16W 5%

C120

C118

C119

4K7 1/16W 5%

VCC A0

SCL A2

SDA VSS

DET_CABLE

DDC2_SCL

DDC2_SDA

候綼　U107

候綼　U105

候綼　U106

DDC_WP

GND POWERDGND

NC / M24C02-WMN6TP

T P V ( Top Victory Electronics Co .

Ltd. )

OEM MODEL

TPV MODEL

Size

Rev

Acer G185H Dual Only

CBPC9M6AFQH

ESD_VCC2

FB109

ESD_VCC1

G2883-1-6-X-37-090901

2.0.INPUT

絬

隔

瓜

絪

腹

Key Component

Date

300 OHM

PCB NAME

Sheet

称爹>

称爹

Tuesday, September 01, 2009

CN301

LVB0M

LVB0P

LVB1M

LVB1P

LVB2M

LVB2P

RXO0-

RXO0+

RXO1-

RXO1+

RXO2-

RXO2+

PA[0..9]

PA0 LVA3P

PA1 LVA3M

PA2 LVACKP

PA3 LVACKM

PA4 LVA2P

PA5 LVA2M

PA6 LVA1P

PA7 LVA1M

PA8 LVA0P

PA9 LVA0M

LVBCKM RXOC-

CN302

LVBCKP

LVB3M

LVB3P

LVA0M

LVA0P

RXOC+

RXO3-

RXO3+

RXE0-

RXE0+

LVA0M

LVA1M

LVA2M

LVACKM

LVA3M

RXE0-

RXE1-

RXE2-

RXEC-

RXE3-

RXE0+

RXE1+

RXE2+

RXEC+

RXE3+

LVA0P

LVA1P

LVA2P

LVACKP

LVA3P

PB[0..9]

LVA1M

LVA1P

RXE1-

RXE1+

PB[0..9]

PB0 LVB3P

PB1 LVB3M

PB2 LVBCKP

PB3 LVBCKM

PB4 LVB2P

PB5 LVB2M

PB6 LVB1P

PB7 LVB1M

PB8 LVB0P

PB9 LVB0M

LVA2M

LVA2P

LVACKM RXEC-

LVACKP

LVA3M

LVA3P

RXE2-

RXE2+

CONN

RXEC+

RXE3-

RXE3+

PANEL_VCC

CMVCC

NC/CONN

U301

R301

330 OHM 1/4W

C301

R303

C302

0.1uF/16V

10K 1/16W 5%

R304

0.1uF/16V

R302

NC\AO4411

Q301

4K7 1/16W 5%

47K 1/16W 5%

AO3401

C303

Q302

2N3906S-RTK/PS

C304

PPWR_ON#

PANEL_VCC

R305

0 OHM +-5% 1/8W

C305

100uF25V

AO3401L

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

TPV MODEL

Size

Rev

Acer G185H Dual Only

CBPC9M6AFQH

G2883-1-6-X-37-090901

絬隔瓜絪腹

Key Component

3.0.OUTPUT

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

Date

CMVCC

VCC1.8

C710

0.1uF 16V

FB702

300 OHM

CN701

VCC3.3

C705

C704

100uF25V

SM340A

D701

MVCC

0.1uF/16V

CMVCC

BKLT-VBRI

BKLT-EN

PANEL_ID#

Volume#

Mute

Q702

KN2907AS

R705

10K 1/16W 5%

R706

R709

R710 NC

Volume#

PANEL_ID#

FB704

Q703

KN2907AS

BKLT-VBRI

Mute

adj_BACKLIGHT

VCC3.3

1K 1/16W 5%

CONN

C713

C701

0.1uF/16V

R708

NC/2.2 OHM 2W

C712

lock type

R701

0R05 1/4W

DGND

1,2,3

VCTRL

DVI_5V DSUB_5V

D702

VCC3.3

R702

VCC3.3

D702

BAT54C

External EDID

MVCC_1

Internal EDID BAT54C

10K 1/16W 5%

R703

10K 1/16W 5%

FB701

BKLT-EN

FB703

300 OHM

C711

R701

0R05 1/4W

R708

U701

223

C702

0.1uF 16V

MVCC

VCC3.3

TSUM5PFHL

R704

U701

VIN

on_BACKLIGHT

TSUMU58EHL

TSUMO58CWHL

3.3 OHM 2W 223

3.3 OHM 2W 252

VOUT

Q701

4K7 1/16W 5%

2N3904S-RTK/PS

C707

C706

C708

AP1117E33LA

C709

100uF25V

0.1uF/16V

100uF25V

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

Size

Rev

Acer G185H Dual Only

CBPC9M6AFQH

G2883-1-6-X-37-090901

TPV MODEL

絬

隔瓜絪腹

Key Component

Date

4.0.POWER

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

VCC1.8

VDDC

VDDP

FB403

VCC3.3 FB401

AVDD VCC3.3 FB402

VPLL

VCC3.3

VCC1.8

0 OHM +-5% 1/8W

C412

300OHM

VCC3.3

C409

C408

0.1uF/16V

C403

C404

C406

C402

10uF/50V 0.1uF/16V

C410 C411

0.1uF/16V

C407

0.1uF/16V

C405

0.1uF/16V 0.1uF/16V

0.1uF/16V

VDVI VMPLL VPLL AVDD VDDP

VDDC

0.1uF/16V

VCC3.3 FB404

300OHM

VMPLL

VCC3.3

VDVI

VCC3.3

VCTRL

R403

0 OHM +-5% 1/8W

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PA8

PA9

LVA3P

LVA3M

LVACKP

LVACKM

LVA2P

LVA2M

LVA1P

LVA1M

LVA0P

LVA0M

DSUB_R+

RIN0P

RIN0M

GIN0P

GIN0M

SOGIN0

BIN0P

BIN0M

HSYNC0

C414

0.1uF/16V

C415

0.1uF/16V

DSUB_R-

DSUB_G+

DSUB_G-

DSUB_SOG

DSUB_B+

DSUB_B-

DSUB_H

DSUB_V

DDC1_SDA

DDC1_SCL

R402

C413

0.1uF/16V

R404

Q405

VSYNC0

DDCA_SDA/RS232_TX

DDCA_SCL/rs232_RX

LF_B

100

R405

RX2P

RX2N

RX1P

RX1N

RX0P

RX0N

RXCP

RXCN

DDC2_SDA

DDC2_SCL

R+

R-

G+

G-

B+

B-

CK+

CK-

PA[0..9]

PB[0..9]

DVI_5V

PA[0..9]

PB[0..9]

DDC_WP

R447

R406

PB0

PB1

PB2

PB3

PB4

PB5

PB6

PB7

PB8

PB9

Q401

LVB3P

LVB3M

LVBCKP

LVBCKM

LVB2P

LVB2M

LVB1P

LVB1M

LVB0P

LVB0M

R407

C416

DDCD_SDA

DDCD_SCL

R446

AVDD

REXT

MVCC

R401 390 OHM 1/16W

TSUMU5PEHL-LF

0.1uF/16V 26

C417

CMVCC

REFP

REFM

R448

VCC3.3

Q406

10K 1/16W 5%

EE_WP

GPIO_P23

GPIO_P22

C401

0.22uF16V

AO3401

R410

R445

R409

NC/100R 1/16W 5%

100R 1/16W 5%

PANEL_ID#

U402

GPIO_P15/PWM0

PWM2/GPIO_P24

R412

10K 1/16W 5%

LVDS

CS# VCC

DO HOLD#

WP# CLK

SDO

SCZ

SCK

SDI

6K8 1/16W 5%

on_BACKLIGHT

adj_BACKLIGHT

GPIO_P12

PWM1/GPIO_P25

R449

VSS

RSTN

GPIO_P00/SAR1

GPIO_P01/SAR2

GPIO_P02/SAR3

R415

R416

R417

100R 1/16W 5%

KEY1

KEY2

47K1/16W

EN25F20-100GCP

PPWR_ON#

GPIO_P27/PWM1

RST

C418

0.1uF/16V

R413

10K 1/16W 5%

C419

DET_CABLE

Reduce the luminance of LED-090901

MVCC

R419

R420

R422

1K1/16W

620R 1/16W 5%

LED_GRN/BLUE

LED_ORANGE

GPIO_P06

GPIO_P07

10UF50V

R421

100K 1/16W 5%

PWM0/GPIO_P26

GPIO_P13

R423

0R05 1/16W 96

HDCP_CTRL

Mute

R424

R425

R426

CMVCC

XI N

GPIO_P14

C420 47pF

C421 47pF

100R 1/16W 5%

POWER_KEY#

VCC3.3

GPIO_P16/PWM2

X401

14.31818MHz

CMVCC

10K 1/16W 5%

XOUT

BYPASS

R427

CMVCC

R428 100R 1/16W 5%

C422 0.1uF/16V80

C437

10UF50V

NC/10K 1/16W 5%

R450

R430

100K 1/16W 5%

FB406

R429

R431

MSCL

MSDA

Volume#

GPIO_P10/I2C_MCL

GPIO_P11/I2C_MDA

MODE[0]

MODE[1]

Q404

VCC3.3

R444

3.9K OHM 1% 1/16W

R443

3.9K OHM 1% 1/16W

CN402

C423

KEY2

KEY1

POWER_KEY#

LED_GRN/BLUE

LED_ORANGE

R440

R441

R442

U403

EE_WP

VCC NC

WC E1

MSCL

MSDA

SCL E2

LF_B

C436

SDA VSS

C431

0.1uF/16V

C432

C433

C434

R411

C435

0.1uF/16V

R408

CONN

FB405

0.1uF/16V

10K 1/16W 5%

lock type

T P V ( Top Victory Electronics Co .

Ltd.

)

OEM MODEL

TPV MODEL

Size

Rev

Acer G185H Dual Only

CBPC9M6AFQH

G2883-1-6-X-37-090901

絬

隔

瓜

絪

腹

Key Component

Date

5.0.SCALER

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

T89AM5D8MXAFN2

FB102

BEAD

VGA_B+

VGA_B-

VGA_G+

VGA_G-

VGA_R+

VGA_R-

R105

100R 1/16W 5% C102

0.047uF

DSUB_B+

DSUB_B-

R108

C105

5pF/50V

75R 1/16W 5%

R109

100R 1/16WC51%06

0.047uF

R110

470R 1/16W 5% C107

1000pF

DSUB_SOG

DSUB_G+

FB103

BEAD

R111

100R 1/16W 5% C108

0.047uF

R112

C109

5pF/50V

MVCC_1

75R 1/16W 5%

R114

100R 1/16W 5% C110

0.047uF

DSUB_G-

DSUB_R+

H_Sync R102

V_Sync

0R05 1/10W 5%

R106

R103 1K 1/16W 5%

R104 1K 1/16W 5%

DSUB_H

DSUB_V

D109

R107

C103 C104

22pF

BAT54C

FB101

BEAD

2K2 1/16W 5%

R115

100R 1/16W 5%

C111

22pF

0.047uF

U104

ESD_VCC

DSUB_5V

DSUB_SCL

DSUB_SDA

H_Sync

V_Sync

R116

I/O1 I/O4

GNDVDD

I/O2 I/O3

C113

5pF/50V

CN101

75R 1/16W 5%

FB107

R117

100R 1/16W 5%C114

0.047uF

CMVCC

DSUB_R-

DSUB_5V

R101

100R 1/16W 5%

R113

AZC099-04S

C112

DDC1_SCL

DSUB_SCL 15

VGA_PLUG

DSUB_5V

DDC1_SCL

DDC1_SDA

300 OHM

候綼　U103

VGA_B-

C124

0.1uF 16V

DSUB_SDA 12

VGA_B+

VGA_G-

VGA_G+

VGA_R-

VGA_R+

D104

ZD104

ZD105

RLZ5.6B

VGA_G+

RLZ5.6B

BAT54C

DDC1_SDA

U103

ESD_VCC

100R 1/16W 5%

I/O1 I/O4

GNDVDD

I/O2 I/O3

DB15

VGA_R+

VGA_B+

R123

C116

AZC099-04S

C101

R124

4K7 1/16W 5%

R125

4K7 1/16W 5%

U101

VCC A0

WP A1

SCL A2

候綼　U101

DDC1_SCL

DDC1_SDA

SDA VSS

DDC_WP

NC / M24C02-WMN6TP

CMVCC

C121

1000pF

VCC3.3

R133

10K 1/16W 5%

VGA_PLUGR139

6K8 1/16W 5%

DET_CABLE

GND POWER DGND

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

TPV MODEL

Size

Rev

Acer G185H Analog Only

CBPC9M5AFQN

G2883-1-6-X-42-090901

絬

隔

瓜

絪

腹

Key Component

Date

2.0.INPUT

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

CN301

LVB0M

LVB0P

LVB1M

LVB1P

LVB2M

LVB2P

RXO0-

RXO0+

RXO1-

RXO1+

RXO2-

RXO2+

PA[0..9]

PA0 LVA3P

PA1 LVA3M

PA2 LVACKP

PA3 LVACKM

PA4 LVA2P

PA5 LVA2M

PA6 LVA1P

PA7 LVA1M

PA8 LVA0P

PA9 LVA0M

CN302

LVBCKM RXOC-

LVBCKP

LVB3M

LVB3P

LVA0M

LVA0P

RXOC+

RXO3-

RXO3+

RXE0-

RXE0+

LVA0M

LVA1M

LVA2M

LVACKM

LVA3M

RXE0-

RXE1-

RXE2-

RXEC-

RXE3-

RXE0+

RXE1+

RXE2+

RXEC+

RXE3+

LVA0P

LVA1P

LVA2P

LVACKP

LVA3P

PB[0..9]

LVA1M

LVA1P

RXE1-

RXE1+

PB[0..9]

PB0 LVB3P

PB1 LVB3M

PB2 LVBCKP

PB3 LVBCKM

PB4 LVB2P

PB5 LVB2M

PB6 LVB1P

PB7 LVB1M

PB8 LVB0P

PB9 LVB0M

LVA2M

LVA2P

LVACKM RXEC-

LVACKP

LVA3M

LVA3P

RXE2-

RXE2+

CONN

PANEL_VCC

RXEC+

RXE3-

RXE3+

PANEL_VCC

CMVCC

NC/CONN

U301

R301

330 OHM 1/4W

C301

R303

C302

0.1uF/16V

10K 1/16W 5%

R304

0.1uF/16V

R302

NC\AO4411

Q301

4K7 1/16W 5%

47K 1/16W 5%

AO3401

C303

Q302

2N3906S-RTK/PS

C304

PPWR_ON#

PANEL_VCC

R305

0 OHM +-5% 1/8W

C305

100uF25V

AO3401L

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

Size

Rev

Acer G185H Analog Only

CBPC9M5AFQN

G2883-1-6-X-42-090901

TPV MODEL

絬隔瓜絪腹

Key Component

3.0.OUTPUT

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

Date

CMVCC

VCC1.8

C710

0.1uF 16V

FB702

300 OHM

CN701

VCC3.3

C705

C704

100uF25V

SM340A

D701

MVCC

0.1uF/16V

CMVCC

BKLT-VBRI

BKLT-EN

PANEL_ID#

Volume#

Mute

Q702

KN2907AS

R705

10K 1/16W 5%

R706

R709

R710 NC

Volume#

PANEL_ID#

FB704

Q703

KN2907AS

BKLT-VBRI

Mute

adj_BACKLIGHT

VCC3.3

1K 1/16W 5%

CONN

C713

C701

0.1uF/16V

R708

NC/2.2 OHM 2W

C712

lock type

R701

0R05 1/4W

DGND

1,2,3

VCTRL

DVI_5V DSUB_5V

VCC3.3

R702

VCC3.3

D702

BAT54C

MVCC_1

10K 1/16W 5%

R703

10K 1/16W 5%

FB701

BKLT-EN

FB703

300 OHM

C711

C702

0.1uF 16V

MVCC

VCC3.3

R704

U701

VIN

on_BACKLIGHT

VOUT

Q701

4K7 1/16W 5%

2N3904S-RTK/PS

C707

C706

C708

AP1117E33LA

C709

100uF25V

0.1uF/16V

100uF25V

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

TPV MODEL

Size

Rev

Acer G185H Analog Only

CBPC9M5AFQN

G2883-1-6-X-42-090901

絬隔瓜絪腹

Key Component

Date

4.0.POWER

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

VCC1.8

VDDC

VDDP

FB403

VCC3.3 FB401

AVDD VCC3.3 FB402

VPLL

VCC3.3

VCC1.8

OHM +-5% 1/8W

C412

300OHM

VCC3.3

C409

C408

0.1uF/16V

C403

C404

C406

C402

10uF/50V 0.1uF/16V

C410 C411

0.1uF/16V

C407

0.1uF/16V

C405

0.1uF/16V 0.1uF/16V

0.1uF/16V

VDVI VMPLLVPLL AVDD

VDDP

VDDC

0.1uF/16V

VCC3.3 FB404

300OHM

VMPLL

VCC3.3

VDVI

VCC3.3

VCTRL

R403

OHM +-5% 1/8W

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PA7

PA8

PA9

LVA3P

LVA3M

LVACKP

LVACKM

LVA2P

LVA2M

LVA1P

LVA1M

LVA0P

LVA0M

DSUB_R+

RIN0P

RIN0M

GIN0P

GIN0M

SOGIN0

BIN0P

BIN0M

HSYNC0

C414

0.1uF/16V

C415

0.1uF/16V

DSUB_R-

DSUB_G+

DSUB_G-

DSUB_SOG

DSUB_B+

DSUB_B-

DSUB_H

DSUB_V

DDC1_SDA

DDC1_SCL

R402

C413

0.1uF/16V

R404

Q405

VSYNC0

DDCA_SDA/RS232_TX

DDCA_SCL/rs232_RX

LF_B

100

R405

RX2P

RX2N

RX1P

RX1N

RX0P

RX0N

RXCP

RXCN

DDC2_SDA

DDC2_SCL

PA[0..9]

PB[0..9]

DVI_5V

PA[0..9]

PB[0..9]

DDC_WP

R447

R406

PB0

PB1

PB2

PB3

PB4

PB5

PB6

PB7

PB8

PB9

Q401

LVB3P

LVB3M

LVBCKP

LVBCKM

LVB2P

LVB2M

LVB1P

LVB1M

R407

C416

R446

AVDD

REXT

LVB0P

LVB0M

MVCC

R401 390 OHM 1/16W

TSUM1PEL

0.1uF/16V 26

C417

CMVCC

REFP

REFM

GPIO_P40

GPIO_P41

GPIO_P42

R448

VCC3.3

Q406

10K 1/16W 5%

EE_WP

GPIO_P23

GPIO_P22

C401

0.22uF16V

AO3401

R410

R445

R409

NC/100R 1/16W 5%

100R 1/16W 5%

PANEL_ID#

U402

GPIO_P22/PWM0

PWM2/GPIO_P24

R412

10K 1/16W 5%

LVDS

CS# VCC

DO HOLD#

WP# CLK

SDO

SCZ

SCK

SDI

6K8 1/16W 5%

on_BACKLIGHT

adj_BACKLIGHT

GPIO_P12

PWM1/GPIO_P25

R449

VSS

GPIO_P17/SAR0

GPIO_P00/SAR1

GPIO_P01/SAR2

GPIO_P02/SAR3

R415

R416

R417

100R 1/16W 5%

KEY1

KEY2

47K1/16W

EN25F20-100GCP

PPWR_ON#

GPIO_P27/PWM1

C418

0.1uF/16V

R413

10K 1/16W 5%

C419

DET_CABLE

Reduce the luminance of LED-090901

MVCC

RST

R419

R420

R422

1K1/16W

620R 1/16W 5%

LED_GRN/BLUE

LED_ORANGE

GPIO_P06

GPIO_P07

PWM0/GPIO_P26

GPIO_P13

GPIO_P14

GPIO_P16/PWM2

10UF50V

R421

100K 1/16W 5%

R423

0R05 1/16W 96

HDCP_CTRL

Mute

R424

R425

R426

CMVCC

XIN

C420 47pF

C421 47pF

100R 1/16W 5%

POWER_KEY#

VCC3.3

X401

14.31818MHz

CMVCC

10K 1/16W 5%

XOUT

BYPASS

R427

CMVCC

R428 100R 1/16W 5%

C422 0.1uF/16V80

C437

10UF50V

NC/10K 1/16W 5%

R450

R430

100K 1/16W 5%

FB406

Volume#

GPIO_P10/I2C_MCL

GPIO_P11/I2C_MDA

MODE[0]

MODE[1]

Q404

VCC3.3

R444

R443

3.9K OHM 1% 1/16W

CN402

3.9K OHM 1% 1/16W

C423

KEY2

KEY1

POWER_KEY#

LED_GRN/BLUE

LED_ORANGE

R440

R441

R442

U403

EE_WP

VCC NC

WC E1

SCL E2

SDA VSS

MSCL

MSDA

LF_B

C436

C431

C432

C433

C434

R411

C435

0.1uF/16V

R408

10K 1/16W 5%

CONN

FB405

0.1uF/16V

10K 1/16W 5%

lock type

T P

(

Top Victory Electronics Co

G2883-1-6-X-42-090901

Ltd.

)

OEM MODEL

TPV MODEL

Size

Acer G185H Analog Only

CBPC9M5AFQN

絬

隔

瓜

絪

腹

Rev

Key Component

Date

5.0.SCALER

PCB NAME

Sheet

<称爹>

称爹

Tuesday, September 01, 2009

Power board

R929 100 OHM 1/4W

BD901

C916

F801

KBP208G

R930 100 OHM 1/4W 0.001uF

0R05 1/4W 5% +14.5V

R903 100 OHM 1/4W

ZD901

R904

220 OHM 2W

MTZJ T-72 16B

D901

NC/SR5150

C918

1000UF25V

R905

470R 1/10W 5%

D902

SB5150

Q904

2SD1207T

R906

100KOHM +-5% 2WS

T901

C911

1500PF2KV

POWER X'FMR

R907

1K 1/10W 1%

R931

C937

C923

0.001uF

R909 100 OHM 1/4W

R910 100 OHM 1/4W

R912 100 OHM 1/4W

C909

NC/0.22uF/275V

0.01uF/2KV

D903

FR107

C917

0.001uF

L906

F901

C907

82uF 450V

R908

10K OHM 1/4W +-5%

FUSE

+5V

R932

1000uF M 16V

C925

D904

FR103

L901

1000PF/250VAC

C938

C920

1000UF25V

C922

470uF 16V

R913

D905 NC/31DQ06FC3

C913

1.5 OHM 1/4W +-5%

22uF/50V

R933

30mH

R901

D906

D907

D908

NC/IN4148

R921

IN4148

U901

NC/100K 1/10W 1%

FMW-2156

R917

COMPNC

CS VCC

GNDOUT

R900

620K OHM 1/4W R902

10R 1/4W 5%

Q901

FMA07N65GX

C927

R919

150R 1/8W 5%

620K OHM 1/4W

LD7576

0.047uF

R934

C912

0.1uF/25V

R918

10K 1/10W 1%

FB901

BEAD

R920

1K 1/10W 1%

C908

0.47uF/275V

C914

470pF

R923

220 OHM 1/4W

U902

PC123X2YFZOF

NR901

NTCR

R914

43.2K OHM 1% 1/4W

R924

0.39 OHM 2W +-5%

C924

0.1uF/16V

F902

FUSE

R916

3.65K OHM 1% 1/10W

R928

1K 1/10W 1%

C902

C903

C900

U903

KIA431A-AT/P

1000pF

C915

0.0022UF

R925

2.43K OHM 1% 1/10W

R935

CN902

L907

F903

CN901

SOCKET

MUTE

VOL

+5V1

HS1

HS2

+5V

HEAT SINK(Q901)

NC/HEAT SINK(D906_5V/4A)

C921

NC/1000uF25V

C931

NC/470uF/16V

ON/OFF

DIM

C926

0.1uF/16V

Wire Harness

HS3

HEAT SINK(D906_5V/2.5A)

GND1

GND

Custom

T P V ( Top Victory Electronics Co .

Ltd.

)

OEM MODEL

Size

Rev

ACER 22" LCD

G2892-2-3-X-21-090817

TPV MODEL PWPC9821AQMY

絬

隔

瓜

絪

腹

Key Component

Date

01.POWER

PCB NAME

Sheet

715G2892-2-3

ODM MODEL

称爹

Saturday , August 15, 2009

REF

+14.5V

C811

470uF 25V

R805

10K 1/10W 5%

CN801

C814

1uF 25V

R803

R816

CONN

0.1uF50V

C801

5pF6KV

LI1

2K 1/10W 5%

10 OHM +-5% 1/10W

R807

T801

POWER X'F7MR

RJ805

OV2

R811

C815

DIM

R815

C802

0.0022uF/50V

10K 1/10W 5%

C809

0.001uF

0R05 1/4W 5%

C813

10 OHM +-5% 1/10W

R801

412 OHM 1/10W

D803

2N2 50V

R817

0.01uF

AM9000ES

BAW56

C806

0.047uF

ON/OFF

Q803

C810

RJ807

RJ803

DBRT

VIN

10K 1/10W 5%

RJ801

0R05 1/4W 5%

FSET

20K 1/10W 1%

R813

0R05 1/4W 5%

R810

100K 1/10W 5%

C808

COMP

LI2

VCC

GND

OV1

R809

3.3 OHM +-5% 1/10W

0R05 1/4W 5%

LI1

OV2

P8008HV

REF

1uF 16V

C805

RJ806

0R05 1/4W 5%

U801

C812

C807

R814

REF

0.0039uF/16V

1uF 16V

R806

CN802

10K 1/10W 5%

2N2 50V

10 OHM +-5% 1/10W

R812

3.3 OHM +-5% 1/10W

R804

LI2

OV2

LI1

OV1

CONN

C803

LI2

5pF6KV

2K 1/10W 5%

RJ802

R808

OV1

0R05 1/4W 5%

10K 1/10W 5%

C804

0.0022uF/50V

R802

412 OHM 1/10W

RJ804

0R05 1/4W 5%

Custom

T P V ( Top Victory

Electronics Co .

Ltd.

)

OEM MODEL

TPV MODEL

Size

PWPC9821AQMY

G2892-2-3-X-21-090817

絬

隔

瓜

絪

腹

Rev

Key Component

Date

02.INVERTER

PCB NAME

Sheet

715G2892-2-3

ODM MODEL

称爹

Saturday , August 15, 2009

Key board

ZD007

NC/UDZSNP5.6B

LED001

LED

ZD008

NC/UDZSNP5.6B

CN001

LBADC1

LBADC2

DC_POWERON

LED_GRN#

LED_RED#

R002

2Kohm 1/10W +/-1%

LED_GRN#

LED_RED#

R004

R005

2Kohm 1/10W +/-1%

1K 1/10W 1%

CONN

C001

C002 C003

NC 0.1uF 50V

C004

0.1uF 50V

C005

SW001

GND

SW006

SW003

SW004

SW002

SW005

MENU(2K)

VOL- (GND)

VOL+(2K)

AUTO(1K)

1.1V

GND

LBADC1

LBADC2

0 V

1.1V

0.65V

ECOLOR(GND) 0 V

CN001

CONNECTOR LED POWER

ECOLOR AUTO MENU

VOL-

VOL+

T P V ( Top Victory Electronics Co . , Ltd. )

OEM MODEL

TPV MODEL

Size

G series

G3573-1-X-X-2-20090629

絬

隔

瓜

絪

腹

ACER

715G3573-1

Rev

Key Component

Date

02.Key Board

PCB NAME

Sheet

称爹>

称爹

Thursday, July 09, 2009

HP Hewlett Packard Compaq Business LA2306x 23 LED LCD Monitor C0H31A8#ABA User Manual
GPX CRT Television TDE1982 User Manual
Fujitsu Siemens Computers Fujitsu Siemens SCENICVIEW P20 2 User Manual
Electrolux Thermaline 9CHG584143 User Manual
Dell Computer Monitor E1912H User Manual
Dacor EPICURE EG486 User Manual
CTX PV720A User Manual
Boston Acoustics S95 User Manual
Bertazzoni C36500X Z36500X, C36600X Z36600X User Manual
Antec MX 25 User Manual