Acer B223W User Manual

Acer

Acer –LCD-B223W

Service Manual

LCD Monitor Acer B223W

- 0 -

Acer

Acer –LCD-B223W

Important Safety Notice

1. Safety precautions

This monitor is manufactured and tested on a ground principle that a user’s safety comes first.

However, improper used or installation may cause damage to the monitor as well as to the user.

Warning:

This monitor should be operated only at the correct power sources indicated on the label on the

rear of the monitor. If you’re unsure of the power supply in you residence, consult your local dealer

or Power Company.

Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor

should only be repaired by a qualified technician.

Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric

shock to human bodies.

Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.

Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable

immediately and consult your closed dealer.

Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply

non-ammonia based cleaner onto the cloth, not directly onto the class screen.

Do not place heavy objects on the monitor or power cord.

2. Product safety notice

Many electrical and mechanical parts in this chassis have special safety visual inspections and the

protection afforded by them cannot necessarily be obtained by using replacement components rated

for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this

manual carefully. The use of substitute replacement parts, which do not have the same safety

characteristics as specified in the parts list, may create shock, fire, or other hazards.

3. Service notes

When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.

Keep wires away from high voltage, high temperature components and sharp edges.

Keep wires in their original position so as to reduce interference.

Adjustment of this product please refers to the user’ manual.

Acer

Acer –LCD-B223W

01 Product Specification

1. General:

BV223W series LCD monitor is designed with a wide screen 22.0” WSXGA+ TFT LCD panel, LVDS interface, Analog RGB

signal input.

It featured with embedded universal AC power supply. This monitor can support maximum resolution up to 1680 x

1050@60Hz.

Details in this document DVI referred to is an option function depending on client’s requirement. In our factory, products

should be distinguished by module names.

1.1 Main Features

Maximum resolution

Back light system

Pixel pitch

: 1680 x 1050 @ 60Hz

: 4 CCFL (top & bottom edge side)

: 0.282 (H) x 0.282 (V)

Display area

: 473.76(H)x296.1(V) 22.0 inch diagonal

Brightness

: ≥250cd/m²

Contrast ratio

: 1000

1 (typ.)

: 5ms (typ.)

(1)

(2)

Response time (Tr+Tf)

Viewing angle

: 160°(H)/ 160°(V), typ

: Analog (D-sub 15 pin)

(3)

Input interface

Digital Option(DVI-D 24 pin)

Power management

Plug & Play

: Compatible with VESA DPMS

: VESA DDCCI

OSD language

: English, French, Spanish, Italian, Deutsch, Simplified Chinese,

Traditional Chinese, Japanese (Dutch, Finnish, Russian depend on sale region)

Universal AC power supply

Note (1)(2)(3): This item spec depend on the LCD panel.

1.2 Accessories

AC Power Cord

VGA cable

: 1.8 m. (Black. Cord type depend on sale region)

: 1.8 m. (15 pin D-SUB, black cable with blue male connector)

: English (640Mb CD)

User manual

Warranty card

DVI cable (option)

: 1.8 m. (18+1 pin, black cable with white connector)

2. Operation Specifications

The unit should suffer no visible cosmetic damage and should operate with no degradation in display quality during

exposure to the operating conditions and after exposure to the non-operating conditions, in any sequence.

2.1.1 Operating:

Temperature range

Relative humidity

: 0°C to 40°C

: 20% to 90%

2.1.2 Storage^{note 1}

Temperature range

Humidity range

: -20°C to 60°C

: 10% to 90%

2.1.3 Altitude ^{note 2}

Operating

10000 ft (Ta=50, t=24h)

40000 ft (Ta=30, t=24h )

Storage

Note 1: Temperature and relative humidity range must be in the area shown as the following figure due to panel limited

Acer

Acer –LCD-B223W

Note 2: Altitude spec must not over panel spec.

Figure 1 Absolute Ratings of Environment

2.1 Safety, EMC, Ergonomics and Compatibility Requirements

cUL, UL, CE, CB, CCC, TUV/GS, TUV/EGO,

Safety & EMC

TUV/ISO-13406-2, C-Tick (N214), VCCI, FCC, CE, CCC,

BSMI, C-Tick

Ergonomics

TCO99, TCO03

Compatibility

Windows 98/Me/2000, Windows XP, Window Vista

Energy Star V4

Power Management

2.2 Electrostatic Discharge Requirements

The subject unit must withstand ±8KV for contact discharge and ±15KV for air discharge of Electrostatic Discharge and

meet the standard of IEC61000-4-2(EN55024). (without discharge on VGA/DVI/HDMI pin)

2.3 Reliability

The MTBF of this product shall be greater than 40,000 hours excluding the LCD panel. The LCD panel life which is

defined as the time period for the maximum luminance to reduce to 50% of the initial value is 40,000 hours minimum at

the condition of displaying an all WHITE field at mid Brightness and Contrast settings.

3. Electrical and Optical Characteristics and Performance

3.1 Backlight Power Supply

3.1.1 AC Input Voltage Range

It is a universal type and the input voltage range is from 100 ~ 240Vrms

3.1.2 AC Input Current

1.2A (max) at 100VAC input

0.6A (max) at 240VAC input

3.1.3 AC Frequency Range

The frequency range is from 50Hz to 60Hz

3.1.4 Inrush Current

a. 40A max at cold-start, 25°C, DC output full-loading and 100Vac input

b. 60A max at cold-start, 25°C, DC output full-loading and 240Vac input

Notes: 1. Before each test, the buck capacitor need to be discharged.

2. Before each test, it must be 10 minutes at least after the latest test.

3.1.5 Regulator Efficiency≥75%

Acer

Acer –LCD-B223W

(DC output full loading and nominal AC input voltage range)

3.1.6 Ripple and Noise

Total composite ripple and noise less than 320mV for +16V output, and less than 150mV for +5V output, and 50mV for

+3.3V output tested by DC loading side parallel with a 47uF/EC and 0.1uF/Ceramic. Capacitors and measured band-width

with DC-20MHz

3.1.7 DC Output Voltage and Current

Current

Typ.

DC Output

Voltage

Max.

2.2 A

1.8A

VCC16V

VCC5V

15.2V-18.5V

4.75~5.25V

1.8A

1.5A

Note: For the normal loading test ,the output loading use typical current.

3.1.8 Protection

a. SCP: For short circuited protection and with auto-recovery function.(for 5V output it must be shorted before F802)

b. OPP: Over-power protection, Range: 60W ( min ) on nominal AC input.

c. BOP: Brown Out protection

Condition: Pattern: Dot pattern,

Timing: 1680x1050 60Hz,

Brightness: Max.

Contrast: Max

Spec:

system shutdown voltage must be > 50V

system restart voltage must be <85V

3.1.9 Power consumption

Max. 55W.

Follow Energy Star V4 condition 49W

3.1.10 Power management

BV223W supports Energy Star V4 and VESA DPMS

Status

H-sync V-sync Video

Power

LED

Blue

On Mode/Active Power

active

≤ 55W

off

blanked

< 2W

< 1W

Orange

Off

Sleep Mode/Low Power

Off Mode/Standby Power

3.2Backlight

Item

Symbol Min.

Typ.

Max.

Unit Remark

Input Voltage

Vin

15.2

2.0

16.0

3.3

---

18.5

5.5

Von

Voff

Enable (On/Off)

-0.3

0.8

Kick off Voltage:

Item

Symbol Min.

1700

Typ. Max.

--- ---

Unit

Remark

Kick off Voltage Vs

Vrms

Acer

Acer –LCD-B223W

On Load Function:

Item Symbol Min.

Typ.

1.8

Max.

2.2

Unit

Remark

Input Current

---

Frequency

I_L

40.0

45.0

kHz

@Max-Load

Output Current for

One Lamp

PWM dimming control

mode: 2mA≤I_L≤8mA

3.0

---

7.0

8.0

---

mArms

Vrms

750

Operating Voltage

Brightness PWM

duty

Kick Off Voltage

Hold Up Time

35%

1.0

---

100%

---

@Vin=16.0V

Brightness=3.3V

1.5

---

@Vin=16.0V

Brightness=3.3V

75%

---

Efficiency

3.3 Brightness output

The test to verify specifications in this section shall be performed under the following standard conditions unless

otherwise noted.

Temperature

: 25 ± 5°C

Test pattern

: white

Video Resolution

Video input level

Warm-up time

: 1680 x 1050

: 700 mV ± 2%

: 30 minutes

Set brightness control and also contrast control at maximum, to measure the screen center, the light output

shall ≥ 250 cd/m²(as panel spec)

3.4 White balance

The test standard conditions refer to Sec 3.3.(Brightness control is at 100 contrast control is at 50 )

Chromaticity Coordinate

Mode

Cool

Warm

User

9300K

6500K

0.283 ± 0.030

0.313 ± 0.030

Panel While x

0.297 ± 0.030

0.329 ± 0.030

Panel While y

3.5 Brightness uniformity

The test standard conditions refer to Sec 3.4.

Min. luminance of nine points (backlight)

75%

≥

Max.luminance of nine points (backlight)

Acer

Acer –LCD-B223W

L/10

L/2

W/10

W/2

4. Input / Output Signal Specifications

4.1 Video signals

Analog RGB signal:

Sync:

0.7Vp-p (Input impedance = 75 Ohm)

TTL level (Input impedance ≧ 1k Ohm)

Positive and negative sync of Separate Horizontal/Vertical Sync

Digital : TMDS Signal: (min) ±200mVpp@24Bit

4.2 Signal Timing

Through D-SUB/DVI connectors, this unit can support F_H= 31.5~84 KHz, Fv=56~76Hz, with maximum

pixel clock 165MHz input signal and WSXGA+ output. Modes details as below:

VESA MODES

Horizontal

Vertical

Nominal

Pixel Clock

(MHz)

Mode

Resolution

Total

Nominal

Frequency

+/-0.5KHz

Nominal

Frequency

+/-1Hz

Sync

Polarity

Sync

Polarity

640*480@60Hz

640*480@72Hz

640*480@75Hz

800*600@56Hz

800*600@60Hz

800*600@72Hz

800*600@75Hz

1024*768@60Hz

1024*768@70Hz

1024*768@75Hz

1152*864@75Hz

1280*960@60Hz

1152*720@60Hz

1280*1024@60Hz

1280*1024@75Hz

1400x1050@60Hz

31.469

37.861

37.500

35.156

37.879

48.077

46.875

48.363

56.476

60.023

67.500

60.000

44.859

63.981

79.976

65.317

59.941

72.809

75.000

56.250

60.317

72.188

75.000

60.004

70.069

75.029

75.000

60.000

59.972

60.020

75.025

59.978

25.175

31.500

36.000

40.000

50.000

49.500

65.000

75.000

78.750

108.000

66.750

108.000

135.000

121.75

VGA

SVGA

XGA

SXGA

SXGA+

Acer

Acer –LCD-B223W

UXGA

1600*1200@60Hz

1360*768@60Hz

1440*900(Red)@60Hz

1440*900@75Hz

75.000

47.712

55.469

70.635

65.290

60.000

60.015

59.901

74.984

59.954

162.000

WXGA

85.5

88.75

WXGA+

136.75

146.250

WSXGA+ 1680*1050@60Hz

IBM MODES

640*350@70Hz

EGA

31.469

70.087

25.175

28.322

720x400@70Hz

MAC MODES

VGA

640*480@66.7Hz

832*624@75Hz

1024*768@75Hz

1152*870@75Hz

35.000

49.725

60.241

68.681

66.667

74.550

74.927

75.062

30.240

57.283

80.000

100.00

SVGA

XGA

Other MODES

XGA

1024*768@72Hz

1280*1024@70Hz

57.669

74.882

72.086

69.853

78.434

127.000

SXGA

Note: 1. Non-interlace signals only (An interlace signal cannot be display)

2. Please refer to F/W specification for more detail

3. Each frequency of Power Macintosh and Sun Ultra is a reference value

4.3 Timing requirements

The LCD monitor must be capable of displaying standard resolutions within the vertical frequency range of 56 ~ 76 Hz

and the horizontal scan range of 31.5 ~ 84 KHz with maximum pixel clock of 190MHz.

Vertical / Horizontal Sync polarity: positive or negative.

If input signal is out of range of horizontal 31.5~84 KHz or vertical 56-76Hz, or pixel clock large than 165MHz, message

“Input Not Supported” is shown on screen.

4.1DDC data

V223W Analog

EA DE 95

A3 54

40 01

4C 99

BF EF 90

1A 27

FD 00

DA 28

4D 1F

0A 00

20 20

Acer

Acer –LCD-B223W

V223W DVI

FF FF FF FF FF FF 00

1B 00 00

2F 1E 78

A9 40

EA DE 95

A3 54

40 01

1A 27

FD 00

00 00

0A 00

20 20

4C 99

BF EF 90

4F 81

0F 90

DA 28

4D 1F

0A 20

FF 00

0A 20

5. Function Specifications

All the tests to verify specifications in this section shall be performed under the following standard conditions

unless otherwise noted. The standard conditions are:

Temperature

: 25 ± 5°C

Warm-up time

: 30 minutes minimum

: All the specified modes

Checking display modes

5.1Panel general specifications

General specifications

InnoLux

Supplier

INL MT190AW01(V-5)

Model name

Display Area

Pixel Pitch

410.4 ( H ) x256.5 ( V )

0.285(H) x 0.285(V)

Display Colors:

16.7 Million (6-bit + HI-- FRC)

Number of Pixel

Pixel Arrangement

Brightness

1440x900 pixels

RGB vertical stripe

300cd/m²(Typ.) 250cd/m²(Min.)

700:1 Typical

Contrast Ratio

Hor:160°, Ver: 160°

(Typical, CR>10)

Viewing Angle

Display Mode

Frame rate

Normally White

75Hz

Response Time

Tr + Tf = 5ms Typical

Anti-glare, Haze = 25%,

Hard coating (3H)

Surface Treatment

Lamp

4 CCFL

Outline Dimension

427.2(W)x277.4(H)x16(D) Typ

5.2Keypad Function

5.2.1

Control buttons on the front bezel

CONTROL KEY

KEYS FUNCTION

A. When OSD un-displays, press [AUTO] to perform auto-adjustment

B. When OSD displays, press [AUTO] to return to previous level menu

C. When “e Color OSD” OSD displays, press [AUTO] to exit the OSD

[AUTO]

Acer

Acer –LCD-B223W

A. When OSD isn’t shown on screen, press [MENU] to enter OSD interface. The OSD

interface uses “ACER e Color Management” and “User” to instead “Contrast” and

“Brightness” separately. When press “ACER e Color Management” to show “e Color

OSD”, and press “User” to show OSD interface before. The translations of “ACER e

Color Management” and “User” are always English.

[MENU]

B. When OSD displays, press [MENU] to perform function of menu icon that is highlight or

enter next level menu

A. When “MENU OSD” displays, press these keys to change the contents of an

adjustment item, or change an adjustment value

[►], [◄]

B. When “MENU OSD” un-displays, if it is with audio, press [►] to show “Audio” OSD and

increase the volume, press [◄] to show “Audio” OSD and decrease the volume; else

it has no use to press these keys.

A. When OSD un-displays, press [e Color] to show “e Color OSD”, and press again the

OSD can not disappear, but the time of “e Color OSD” disappearing is reset 10 second

again.

B. When OSD disappear not including “e Color OSD”, press [e Color] to show “e Color

OSD” OSD, the OSD before disappears, but the parameters of it should be saved

[e Color ]

[POWER]

Power on or power off the monitor

5.3Hot Key Operation

HOT KEY OPERATION

AUTO

◄

►

POWER

e Color

FUNCTION

Press [e Color ] & [MENU] at the

same time, and then press

[POWER] for DC power on. OSD

menu will be shown with “F” on the

left top. Select “F” for entering

factory mode.

●

FACTORY MODE

5.4OSD Structure

The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or remote control

unit. The unit shall leave the factory with all OSD controls set to their default values.

First

Second

Third

Control Range

Default Value

User mode

Text mode

---

Contrast

0 ~ 100

Standard mode

Graphics mode

Movie mode

User mode

Brightness

Text mode

Brightness

0 ~ 100

---

Standard mode

Graphics mode

Movie mode

Acer

Acer –LCD-B223W

Focus

0 ~ 100

---

Depend on each timing

Image

Clock

---

50 ○1

Horizontal

Vertical

---

Position

---

Depend on each timing

Warm (6500K)

Cool (9300K)

---

Color

Red

Green

Blue

0 ~ 100

User

NO-EMEA

English

EMEA

English

---

Deutsch

Español

Hollands

Русский

Français

Italiano

---

Español

---

简体中文

繁體中文

Français

Language

---

English

---

Italiano

---

日本語

Suomalainen

---

Hor. Position

Ver. Position

OSD Timeout

Analog

0 ~ 100

10~ 120

---

OSD

---

Input (Dual)

Digital

---

DDCCI ON/OFF

Input (Analg

only)

DDCCI ON/OFF

Resolution

H. Freq

V. Freq

S/N

---

Info

---

ET000….0000(22)

Reset

Exit

---

Notes; ○1 Clock default 50 is for Visa timing. Others depend on timing.

Acer

Acer –LCD-B223W

6. SOP of firmware upgrade

6.1 Operational condition:

Equipment: PC, ISP card, signal cable and power cable.

ESD requirements: antistatic wrists, antistatic gloves (fingers), and connecting cable

Name of ISP program: RTDTool_4.6.exe

：

Manufacture of FW IC RTD 2525L

6.2 Operational steps:

1. Connection: connect PC to PCBA with signal cable, and then keep AC and DC in open state.

One port of ISP

program card

is connected to

PC print port.

2. Adjust ISP programming

Firstly, double click ISP_Tool_v3.7.5EXEI and open ISP program, then select “Device”, next select

manufacturer model of FW IC, which should be correspondent with that of PCBA FW IC. Double click

Figure One.

FW IC

Model

Acer

Acer –LCD-B223W

﹐

Secondly download FW software: first select “READ”, and then load FW software in Rooter

(Fig.2).

FW software

rooter

Software

Checksum

Thirdly, select “Connect” and enter ISP MODE as in the following Figure 3.

Acer

Acer –LCD-B223W

Fourthly, select “AUTO”, and keep its default value. Click “RUN” for beginning programming. There

will be prompting if programming is OK.

Note: if programming fails or success rate is not high, click “Config” and adjust its speed in “E2PROM

DEVICE SETTING”

Acer

Acer –LCD-B223W

After connecting, AC ON,

DC ON

◆Flowing chart

Open ISP program

Choose manufacturer

and model of FW IC

LOAD FW software

Click Connect and enter

ISP MODE

Choose Config

and adjust

programming

Click AUTO and RUN for

beginning programming

Turn off power if

programming is OK

Acer

Acer –LCD-B223W

02. Flat Panel Specification

MT220WW01 V.0

3/23

SPEC NO.

PAGE

Contents:

A. General Specification

B. Electrical Specifications

1. Pin assignment

2. Absolute maximum ratings

3. Electrical characteristics

a. Typical operating conditions

b. Display color vs. input data signals

c. Input signal timing

d. Display position

e. Backlight driving conditions

C. Optical specifications

D. Reliability test items

E. Safety

F. Display quality

G. Handling precaution

H. Label

I. Mechanical drawings

Appendix

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

4/23

SPEC NO.

PAGE

A. General Specification

NO.

Item

Display resolution (pixel)

Active area (mm)

Screen size (inch)

Pixel pitch (mm)

Color configuration

Overall dimension (mm)

Weight (g)

Specification

Remark

1680(H) X 1050(V), WSXGA+ resolution

473.76(H) X 296.1(V)

22 inches diagonal

0.282(H) X 0.282(V)

R, G, B vertical stripe

493.7 (W) X 320.1 (H) X 16.5 (D) (typ.)

2900 (max.)

Surface treatment

Input color signal

Display colors

Anti-glare, Haze = 25%, Hard coating (3H)

8 bit LVDS

16.7 M (6 bit with Hi-FRC)

6 o’clock

Optimum viewing direction

Backlight

4 CCFL

RoHS

RoHS compliance

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

5/23

SPEC NO.

PAGE

B. Electrical Specifications

1.Pin assignment

Connector [

JAE FI-XB30SSRL-HF16, Foxconn GS23302-0311R-7F or mechanical interface equivalent connector.

Pin No.

Symbol

Description

Frame

VSS

RXinO0-

RXinO0+

RXinO1-

RXinO1+

RXinO2-

RXinO2+

VSS

Ground

-LVDS differential data input, Chan 0-Odd

+LVDS differential data input, Chan 0-Odd

-LVDS differential data input, Chan 1-Odd

+LVDS differential data input, Chan 1-Odd

-LVDS differential data input, Chan 2-Odd

+LVDS differential data input, Chan 2-Odd

Ground

RXOC-

RXOC+

RXinO3-

RXinO3+

RXinE0-

RXinE0+

VSS

-LVDS differential Clock input (Odd)

+LVDS differential Clock input (Odd)

-LVDS differential data input, Chan 3-Odd

+LVDS differential data input, Chan 3-Odd

-LVDS differential data input, Chan 0-Even

+LVDS differential data input, Chan 0-Even

Ground

Frame

RXinE1-

RXinE1+

VSS

-LVDS differential data input, Chan 1-Even

+LVDS differential data input, Chan 1-Even

Ground

RXinE2-

RXinE2+

RXEC-

RXEC+

RXinE3-

RXinE3+

VSS

-LVDS differential data input, Chan 2-Even

+LVDS differential data input, Chan 2-Even

-LVDS differential Clock input (Even)

+LVDS differential Clock input (Even)

-LVDS differential data input, Chan 3-Even

+LVDS differential data input, Chan 3-Even

Ground

VSS

Ground

No Connection

VSS

Ground

VCC

+5.0V power supply

VCC

+5.0V power supply

VCC

+5.0V power supply

VSS

Ground

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

6/23

SPEC NO.

PAGE

#30

Rear view of LCM

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

7/23

SPEC NO.

PAGE

2. Absolute maximum ratings

Values

Unit

Parameter

Symbol

Remark

Min.

-0.3

Max.

Power voltage

Input signal voltage

Operating temperature

Storage temperature

CCFL Current

V_cc

V_LH

At 25°C

Note 1

Note 2

4.3

Top

T_ST

°C

- 25

°C

ICFL

[mA]

Note 1: The relative humidity must not exceed 90% non-condensing at temperatures of 40°C or

less. At temperatures greater than 40°C, the wet bulb temperature must not exceed 39°C.

Note 2: The unit should not be exposed to corrosive chemicals.

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

8/23

SPEC NO.

PAGE

3. Electrical characteristics

a. Typical operating conditions

Item

Symbol

V_cc

Min.

4.5

Typ.

Max.

Unit

Remark

Input Voltage

5.5

Permissive Power Input Ripple

V_RF

0.25

Black

I_cc

900

700

800

Note 1

Note 2

Note 3

Note 4

Input Current

White

Mosaic

I_cc

Rush Current

I_Rush

Logic Input

Common Mode Voltage

Differential Input Voltage

Threshold Voltage (High)

Threshold Voltage (Low)

VCM

VID

1.2

Voltage

LVDS:

100

600

100

VTH

VTL

Note 5

IN+, IN-

-100

Note 1 : The specified current is under the V_cc=5V, 25°C, fv=60Hz (frame frequency) condition

whereas black pattern is displayed.

Note 2 : The specified current is under the Vcc =5V, 25#C, fv=60Hz (frame frequency) condition

whereas white pattern is displayed.

Note 3 : The specified current is under the Vcc =5V, 25#C, fv=60Hz (frame frequency) condition

whereas mosaic pattern(black & white [8*6] ) is displayed.

White : 255 Gray

Black : 0 Gray

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

9/23

SPEC NO.

PAGE

Note 4 : test condition :

(1) V_DD= 5 V, V_DDrising time = 470 Čs 10%

(2) Pattern: Mosaic pattern

V_DD

Ton=470 Čs $ 10%

(3) Test circuit

5 V

2SK1059

VDD ( LCD INPUT)

FUSE

47K

1uF

CONTROL SIGNAL

(HIGH to LOW)

2SK1399

12V

47K

1uF

10000pF

Note 5 : LVDS signal definition

VIN₊= Positive differential DATA & CLK Input

VIN- = Negative differential DATA & CLK Input

VID = VIN₊– VIN- ,

∆VCM =$VCM₊–VCM-$,

∆VID =$VID₊–VID-$,

VID+ =$VIH₊–VIH-$,

VID- =$VIL₊–VIL-$,

VCM = (VIN₊+VIN-)/2,

VCM+ = (VIH₊+VIH-)/2,

VCM- = (VIL₊+VIL-)/2,

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

10/23

SPEC NO.

PAGE

Note 6 : Power on sequence for LCD V_DD

Parameter

Value

Typ.

Unit

Min.

Max.

0.1

200

100

250

0.1

1000

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

11/23

SPEC NO.

PAGE

b. Display color vs. input data signals

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color;

the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.

Input color data

Red

Green

Blue

Color

MSB

LSB MSB

LSB

R7 R6 R5 R4 R3 R2 R1 R0

B7 B6 B5 B4 B3 B2 B1 B0

G7 G6 G5 G4 G3 G2 G1 G0

Black

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0 0

1 0 0 0 0 0

Red(255)

Green(255)

Blue(255)

Cyan

Magenta

Yellow

1 1 1 1 1

Basic

colors

0 0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

1 1 1 1 1 1

White

1 1 1 1 1

0 0 0 0 0

Red(000) dark

Red(001)

Red(002)

Red(253)

Red(254)

0 0 0 0 0

0 0 0 0 0 0 0

0 0 0 0 0

Red

Green

Blue

0 0 0 0 0

1 1 1 1 1 1 0

0 0 0 0 0

1 1 1 1 1

Red(255) bright 1 1 1 1 1

Green(000)dark 0 0 0 0 0

0 0 0 0 0

Green(001)

Green(002)

Green(253)

Green(254)

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

Green(255)bright 0 0 0 0 0

Blue(000) dark

Blue(001)

Blue(002)

Blue(253)

Blue(254)

0 0 0 0 0

0 0 0 0 0 0 0

0 0 0 0 0

0 0 0 0 0 0 0

0 0 0 0 0

1 1 1 1 1

0 0 0 0 0

Blue(255) bright 0 0 0 0 0

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

12/23

SPEC NO.

PAGE

c. Input signal timing

Support Input Timing Table

The input signal timing specifications are shown as the following table and timing diagram.

Signal

Clock

Item

Description

period

Min.

12.2

Typ.

16.8

59.6

1080

1050

Max.

Unit

17.9

Dclk

frequency

MHz

T_H

T_{V_TOTAL}

T_{V_DATA}

T_VB

V total line number

Data duration

V-blank

1059

1050

1100

1050

T_H

Vertical

T_H

f_V

frequency

Horizontal

T_{H_TOTAL}

T_{H_DATA}

T_HB

H total pixel number

Data duration

H-blank

890

840

920

840

1004

840

164

DClk

Note: Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

to low logic level or ground. Otherwise, this module would operate abnormally.

INPUT SIGNAL TIMING DIAGRAM

Tvd

Tvb

DCLK

Thb

Thd

DATA

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

13/23

SPEC NO.

PAGE

d. Display Position

D(1, 1)

D(1, 2)

D(2, 1)

D(2, 2)

……

D(840, 1)

D(840, 2)

……

D(1679, 1)

D(1679, 2)

D(1680, 1)

D(1680, 2)

……

D(1, 525)

D(2, 525)

D(840, 525)

D(1679, 525) D(1680, 525)

D(1, 1049)

D(1, 1050)

D(2, 1049)

D(2,1050)

D(840, 1049)

D(840, 1050)

D(1679, 1049) D(1680, 1049)

D(1679,1050) D(1680, 1050)

e. Backlight driving conditions

Parameter

Symbol

Min.

Typ.

Max.

Unit

Remark

Lamp voltage

758(8mA) 794(7mA) 955(3mA) Vrms

Lamp operation current

Lamp starting voltage

mArms

Vrms

Note 1

1250

1570

T = 25Mꢀꢁ Note 2,3,4,5ꢁ

T = 0Mꢀ Note 2,3,4,5

Note 5

VLstart

Frequency

KHZ

Lamp life time

40000

Note 6

Note: The waveform of the voltage output of inverter must be area-symmetric and the design of the

inverter must have specifications for the modularized lamp. The performance of the Backlight,

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter

for the lamp. All the parameters of an inverter should be carefully designed to avoid producing too

much current leakage from high voltage output of the inverter. When designing or ordering the

inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the

inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module

should be operated in the same manners when it is installed in your instrument.

Note 1 :

The degree of unbalance: less than 10%

The ratio of wave height: less than 2 ꢀ10%

Ip: high side peak

I-p

I-p: low side peak

The degree of unbalance = |

The ratio of wave height = p(or I-p)/Irms

Lamp should be completely turned on.

p-I-p| /Irms*100(%)

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

14/23

SPEC NO.

PAGE

Note 2: Test equipment: AS-114B

Note 3: The voltage shown above should be applied to the lamp for more than 1 second after startup.

Otherwise, the lamp may not be turned on normally.

Note 4: Inverter should provide more than min. value, and then lamp could be completely turned on.

Note 5:Lamp frequency may produce interference with horizontal synchronous frequency and this

may cause line flow on the display. Therefore lamp frequency shall be detached from the

horizontal synchronous frequency and its harmonics as far as possible in order to avoid

interference.

Note 6:Lamp life definition: The brightness of lamp becomes 50% of the initial brightness or not

normal lighting.

Backlight connector : 35001HS-02L

Pin no.

Symbol

VIH

Function

Remark

Lamp high voltage input

Lamp low voltage input

Lamp high voltage input

Lamp low voltage input

Cable color: Pink

Cable color: White

Cable color: Blue

Cable color: Black

VIL

VIH

VIL

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

15/23

SPEC NO.

PAGE

C. Optical Specifications

Specification

Item

Symbol

Condition

Unit

Remark

Min.

Typ.

Max.

1.5

Response time

Contrast ratio

3.5

Ĉ= 0`

Note 4

Tr+Tf

θ= 0`

700

1000

Note 3,5

CR"10

CR"5

Top

Bottom

Left

CR"10

CR"5[

CR"10

CR"5[

CR"10

CR"5

Viewing angle

deg.

nit

Note 3,5,7

Right

Brightness (Center)

Note 3,6

Note 3

250

300

[

0.313

0.329

0.640

0.349

0.284

0.617

0.142

0.067

0.80

-0.03

+0.03

Color chromaticity(CIE)

Ĉ= 0`

White uniformity (9 points)

Cross talk

δw

[ [

0.75

Note 3,8

Note 9

[ [

Note 1: Ambient temperature = 25°C.

Note 2: To be measured in dark room after backlight warm up 30 minutes.

Note 3: To be measured with a viewing cone of 2°by Topcon luminance meter BM-5A.

Note 4: Definition of response time: The output signals of BM-7 are measured when the input

signals are changed from “Black” to “White” (falling time) and from “White” to “Black” (rising

time), respectively. The response time interval is between the 10% and 90% of amplitudes.

Refer to figure as below :

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW01 V.0

16/23

SPEC NO.

PAGE

"Black"

"White"

100%

90%

10%

Note 5: Definition of contrast ratio:

Contrast ratio is calculated by the following formula.

Brightness on the "white" state

Contrast ratio (CR)=

Brightness on the "black" state

Note 6: Driving conditions for CCFL: I_L= 7mA, 50 KHz Frequency.

Note 7: Definition of viewing angle.

Note 8: Definition white uniformity:

Luminance are measured at the following nine points (P1~P9).

Minimum Brightness of nine points (P1~P9).

ꢀ

W =

Maximum Brightness of nine points (P1~P9).

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW 01 V.0

17/23

SPEC NO.

PAGE

Note 9:

1/2

1/6

2/3

1/2

1/3

1/6

1/2

1/6

A’

1/3

1/2

B’

2/3

127 gray level

0 gray level

l L_A-L_A’l / L_Ax 100%= 2% max., L_Aand L_A’are brightness at location A and A’

l L_B-L_B’l / L_Bx 100%= 2% max., L_Band L_B’are brightness at location B and B’

Note 10: Optical characteristic measurement setup.

Photo-detector (BM-5A)

Field=2˚

50cm

LCD Panel

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW 01 V.0

SPEC NO.

PAGE :

18/23

D. Reliability test items

Test Item

Test Condition

60°C, 240Hrs

Judgment

Note 1

Remark

Note 2

High temperature storage

Low temperature storage

-25°C, 240Hrs

Note 1

Note 2

High temperature & high

humidity operation

40°C, 90%RH, 240Hrs

(No condensation)

50°C, 240Hrs

High temperature operation

Low temperature operation

Note 1

Note 2

0°C, 240Hrs

Thermal Shock

(non-operation)

-20°C~60°C

1Hr, 10mins, 1Hr, 100cycles

Electrostatic discharge (ESD)

(non-operation)

Note 1

Note 2

Contact:+/-8kV, 150pF(330ohms),

25 times/1 point, 1 time/1 sec

Air discharge:+/-15kV, 150pF(330ohms),

25 times/1 point, 1 time/1 sec

Vibration

Vibration level : 1.5G

Bandwidth : 10-300Hz

Waveform : sine wave,

sweep rate : 10min

Note 1

Note 2

(non-operation)

30 min for each direction X, Y, Z

(1.5 Hrs in total)

Mechanical Shock

(non-operation)

Shock level : 50G, 11ms

Waveform : Half sine wave

Direction : X, Y, Z

Note 1

Note 2

Note 3

One time each direction

MTBF Demonstration

40,000 hours with confidence level 90%

Note1: Pass: Normal display image with no obvious non-uniformity and no line defect. Partial

transformation of the module parts should be ignored.

Fail: No display image, obvious non-uniformity, or line defects.

Note2: Evaluation should be tested after storage at room temperature for one hour.

Note 3: The MTBF (exclude the CCFL ) calculation is based on the assumption that the failure rate

distribution meets the Exponential Model.

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

MT220WW 01 V.0

SPEC NO.

PAGE :

19/23

E. Safety

1. Sharp Edge Requirements

There will be no sharp edges or corners on the display assembly that could cause injury.

2. Materials

a. Toxicity

There will be no carcinogenic materials used anywhere in the display module. If toxic materials

are used, they will be reviewed and approved by the responsible InnoLux Toxicologist.

b. Flammability

All components including electrical components that do not meet the flammability grade UL94-V1

in the module will complete the flammability rating exception approval process. The printed circuit

board will be made from material rated 94-V1 or better. The actual UL flammability rating will be

printed on the printed circuit board.

c. Capacitors

If any polarized capacitors are used in the display assembly, provisions will be made to keep

them from being inserted backwards.

F. Display quality

The display quality of the color TFT-LCD module should be in compliance with the

Innolux’s Incoming inspection standard.

G. Handling precaution

The Handling of the TFT-LCD should be in compliance with the Innolux’s handling principle

standard.

TO ANY OTHER FORMS WITHOUT PRIOR WRITTEN PERMISSION FROM INNOLUX DISPLAY CORPORATION.

Acer

Acer –LCD-B223W

03 Exploded Diagram

3.1 Screw List

Fixed

Item

Part No.

Description

Qty T(kg*cm

)

Remark

SCREW P CROSS W/W-SPR

M3*6 Zn

3.75

0.25 FOR POWER

509146306102R

509000000700R

BOLT,#4-40x11.8,Ni

4.0 0.25

D-SUB CON&DVI

SCREW,P,CROSS,M4*12,BLK-Zn,RO

HS(NYLOK)

50911661210

10.5 0.25 For back-cover to STAND ASSY

SCREW P CROSS W/WAS M3*6

ZN-Cc

3.75

0.25 FOR POWER&IF

509146306200R

Acer

Acer –LCD-B223W

3.2. LCD Exploded drawing (All)

Acer

Acer –LCD-B223W

04 Troubleshooting

1. No Power & LED Off

Unstable power

Check sampling

Circuit

Check R822,

R823, R824

Change R822,R823,

R824

Check the C pin

voltage of IC803

if 3V

Check the R pin

voltage of IC803

about 2.5V

Change

IC803

Check R819, R820

Check pin2 of

IC802 voltage

is 3V

Check R818, D804,

C807 if short

Change

R818, D804,

C807

Check pin1 of

IC802 voltage

below 1V

Change R808, R 809,

R810, R 811, R815,

R814 Q803

END

Acer

Acer –LCD-B223W

2. No raster

N o b ack lig h t

Y es

L ED lam p is O K

Y es

N o p o w e r su p p ly to

inv erter

C h eck th e cab le th at fro m

I/F B D to P/I B D is o k

N o

Y es

Is th ere 1 6 V v o ltag e o n

p in 3 ,4 o f T5 0 1,T 5 02

C hec k p o w e r

su pp ly

N o

U 5 0 1, U 5 0 2 fail

N o

Y es

R eplace U 5 0 1,U 5 0 2

Y es

Is th ere PW M sig n al o n

pin 4 o f IC 5 0 1

N o

C h eck I/F B D

Y es

Is th ere H ig h lev el vo ltag e

o n pin 1 0 o f IC 5 0 1

N o

C h eck I/F B D

Y es

V se nse vo ltage is 2 .9 V

N o

L am p co n n ecto r

o p en ed

Y es

A re there PW M sign al on p in 1 ,

pin 1 5 o f IC 5 0 1

N o

IC 50 1 failu re

Y es

Pin 5 o f IC 5 0 1 v o ltag e is

L ow leve l

Feed ba ck circu it

failu re

C he ck C 5 2 4 ,R 5 28 , R 5 3 3,

D 5 07

Y es

N O

Pin 3 o f IC 50 1 vo ltage is h igh

lev el v o lta ge

C h eck D 5 0 5 , D 5 1 1,

D 5 12 , D 51 3 , R 5 20 , C 5 2 0

Y es

IC 5 01 p ro tected

Y es

EN D

Acer

Acer –LCD-B223W

3.Black screen

B la c k s c re e n

N G

C h e c k p o w e r

s u p p ly :p in 1 ,2 o f

C N 1 0 1

P o w e r fa il

O K

N G

C h e c k

F B 1 0 2 ,F B 1 0 3 ,

C h e c k p o w e r s u p p ly

fo r U 1 0 4

O K

N G

C h e c k re se t (p in 1 0 8 )

o f U 1 0 4

C h e c k C 1 5 1 ,R 1 6 5

O K

N G

C h e c k c ry s ta l (p in

1 2 7 ,1 2 8 ) w a v e fo rm o f

U 1 0 5

C h e c k

X 1 0 1 ,C 1 5 0 ,C 1 5 2

O K

C h e c k C C F L -

E n a b le ,B rig h tn e ss (p in

1 0 9 ,1 2 5 )

O K

C h e c k p in 5 ,6 o f

C N 1 0 1

In v e rte r F a il

o f U 1 0 4

N G

C h e c k R 1 1 1 ,Q 1 0 6 ,

R 1 1 2 ,R 1 4 7 ,R 1 4 8

U 1 0 4 F A IL

Acer

4.Bad Screen

Acer –LCD-B223W

Black screen

Check power

supply:pin 1,2 of

CN101

Power fail

YES

Check power supply

for U104

Check FB102,FB103,

YES

Check reset (pin108)

of U104

Check C151,R165

YES

Check crystal (pin

127,128) waveform of

U105

Check

X101,C150,C152

YES

Check CCFL-

Enable,Brightness(pin

109,125)

YES

Check pin5,6 of

CN101

Inverter Fail

of U104

Check R111,Q106,

R112,R147,R148

U104 FAIL

Acer

Acer –LCD-B223W

5. White screen

White screen

LVDS Cable

Reinsert

Workmanship

Change

LVDSCable

LVDS cable NG

Check VLCD

is 5V

Check LVDS

Panel Fail

signal

Check Panel-Enable of

U104(pin73)

U104 Fail

Check

Q101,Q103,Q104,

R108,R104,C110,C

108

END

Acer

Acer –LCD-B223W

6. No Sound

No sound

Pin1,pin2 of

P701

No sound signal

input

Check 16V Power

supply

Pin13 of U701

Check

Check pin7,pin8 of

CN101

R141,R142,R157,R

158 of IF board

Check

Q701,Q702,Q703,Q

704,R701,R702,

Check Pin3,Pin10 of

U701

Check C705,C707

U701 Fail

Check speaker

Acer

Acer –LCD-B223W

05 Spare parts List

8221D271A1E0R

ET.LBM0C.003

OEM PART NO

DESCRIPTION

791411301601R

PCBA,I/F BOARD(V2,EMEA,W/SPK)LE22D2-612

PCBA,I/F BOARD(V2,W/SPK),LE22D2-612 ROHS

PCBA,P/I BOARD,W/SPK,LE22D2-612 ROHS

PCBA,KEYPAD BOARD,LE9D0-612 ROHS

PWRCORD 16A/250V BLK 6FT VDE/KTL H05VV-F

PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/

CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS

CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH

CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0

HRN ASSY 2x4P 100mm UL1571#28,ROHS

HRN ASSY 2x4P to 8P 245mm UL1571#28,ROHS

HRN LVDS FFC 30P 228mm W/TASTE ROHS

ASSY,STAND,B223W/LE22D2

791411301602R

791411401610R

791401500000R

453070801190R

453070800230R

453030300370R

453010100380R

453030300120R

430300801700R

430300801690R

430303001510R

714011202700R

714030015520R

714050014231R

502090310311R

618100200350R

ASSY,BEZEL,FRONT,(black),B223W/LE22D2

ASSY,COVER,BACK,W/DVI,W/SPK,AUO,B223W/LE

CHASSIS,W/DVI,W/SPK,B223W/LE22D2

SPEAKER 2W 8 340mm 370mm R/G/B W/CASE

＆

631102220180RA

631102220190RA

631102220220RA

LCP 22" M220EW01-V0-000(A)(AUO)ROHS

LCP 22" M220EW01-V0-00A(A)(AUO)ROHS

LCP 22" M220EW01-V0B(AUO)ROHS

Acer

Acer –LCD-B223W

06 Schematics and Layouts

6.1 PI BD Layout

Acer

Acer –LCD-B223W

6.2 IF BD Layout

R827

C815

1000p/500V

C805

2200p/400V

T801

SPW-100

D803 SP10100C

5uH

L802

DC 380V Max.

+16V 3,4

R805

0R2 1W

R831

100Ω 1W

R828

C816

1000p/500V

C817

D801

BL4-06

ZD802

C818

C819

470u/25V

680u/25V /NC

ZD801

13V

C806

4700p/400V

1000u/25V

C804

150u/450V

P6KE150A

D805 SP1040C /NC

Q801

2PC1815GR

R830

200

D802

MUR1100ERL

5uH

L803

DC 650V Max

R806

82K

R807

82K

R808

82K

VCC5V

D804

FR103

F802

5A/35V

C824

470u/16V

D806

SP1040C

R809

FB801

120Ω 3A

C822

C810

0.1/50V

R818

100K 1%

C820

1000u/10V

C823

0.1/50V

L801

20mH

C807

10u/35V

1000u/10V /NC

R810

C812

100P/50V

Q804

R832

VCC

R801

330K

R802

330K

AP2761I

C828

2200p/400V

470Ω 1%

R811

R819

R813

10R

C808

R822

15K4 1%

R823

C826

OVP

BNO

OUT

10K 1%

100p/1KV

100k 1% 0.1/50V

LD7522

IC802

R803 330K

LTV817M

IC801

R816

R826 NC

R833

10K

R820

4K7 1%

C821

0.47/100V

R821

2K2 1%

C814

100p/50V

C803

0.47/275V

R814

10K

R815

0R43 2W

C813

1000p/50V

D807

1N4148

RT801

NTC 5R

IC803

TLV431ALP

F801

2.5A/250V

C809

R824

10K 1%

10u/35V

C801

1000p/400V

C802

1000p/400V

CN801

VCC5V

TO SCALER BD CN101

B223W

C825 0.1/50V

InnoLux

SW801

Document Number :

SIZE :

APPRO BY :

CHECK BY :

DRAWN BY :

SW DPST

ON/OFF

BRIGHTNESS

VOLUME

MUTE

TITLE :

POWER SUPPLY

HDMI_Audio_L

HDMI_Audio_R

PC_HDMI_SWT

12P 2.0mm

2008-01-23

DATE :

SHEET

P801

AC_SKT

Rev :

V01

2,4

+16V

R504

R505

CN501

4100-D02

C501

470u/25V

op1

C502

2.2u/25V

R506

1M5 3KV

C504

1000p/50V

C505

T501

R524

910

1000p/50V SPW-080

D502

R540

BAV99

C506

12p/3KV

8.2K 1%

C508

R510

2K 1%

R517 33

CN502

4100-D02

R521

470

VCC5V

U501

AP9971GD

C509

3p/3KV

C503

D503

R508

43K 1%

BAV99

D504

R507

BAV99

3M3 1%

IS1

2,4 +16V

C513

270p/50V NC

C514

R522

200K

R534 33

R536

6K8 1%

4700p/50V

C530

C531

470u/25V

C507

2.2u/16V

R523

820 1%

R535 33

2200p/50V

op2

R532

R530

DRV1

VDDA

DIM

DRV2

R512

10K

GNDA

TIMER

CN503

4100-D02

C515

2.2u/16V

C529

1000p/50V

R525

BRIGHTNESS

C522

1000p/50V

1M5 3KV

D508 BAV99

ISEN

PID

R527

910

C510

1000p/50V

SSTCMP

LCT

RSTR

R513

68K 1%

R541

8.2K 1%

C526

C523

12p/3KV

OVPT

VSEN

R531

2K 1%

ENA

R542

200K

T502

SPW-080

R515

1M 1%

IC501

INL837

U502

AP9971GD

CN504

4100-D02

R529

470

R520

C528

3p/3KV

30K 1%

D505

SN4148

D511

SN4148

D509

D507

BAV99

IS2

op1

C520

0.1/50V

BAV99

R526

ON/OFF

C525

270p/50V NC

C527

op2

R501

10K

4700p/50V

C524

D512

SN4148

R528

820 1% 6K8 1%

R533

R518

470K 1%

2200p/50V

C518

0.01/50V

R537

10K 1%

R519

C519

0.1/50V

R539

5K1 1%

IS1

IS2

InnoLux

D506

BAT54

Document Number :

SIZE :

Custom

APPRO BY :

CHECK BY :

DRAWN BY :

R538

10K 1%

C517

6800p/50V

doc

TITLE :

Inverter B223W

DATE :

SHEET

2008-01-23

Rev :

V01

+16V

VCC16V

+16V

2,3

R734

0R2 1W

C703

C702

220u/25V

C712

220u/25V

0.1/50V

R701

10K

Line_L

Line_R

P702/NC

U701

TDA8496SA

R732

R733

220/NC

13a

12a

Left_in

C704 0.47/16V

R702

10K

Left_Out

Right_Out

INL

D701

ESD

D702

ESD

OUTL

C706 0.47/16V

220u/25V C705

Right_in

C707

INR

OUTR

SVR

220u/25V

S_GND

MUTE

STBY

ST-510

FB701

VCC16V

600Ω

R717

10K

VAROUT_R

VAROUT_L

R703

R704

47K

VOLUME

CN701

Q702

R705

30K

PMBT3904

4P 2.0mm 90°

Q704

R718

R714

30K

C715

PMBT3904

Q703

220u/25V

FB702

FERR BEAD

MUTE

PMBT3904

VCC16V

R712

5K6

VCC5V

R713

100

Q701

PMBT3904

VOLUME

C720

100u/16V

C716

0.1/16V

Line_L

VCC5V

U702

VCC

Pin9(1B0) PC

Audio L

input

GND

1B0

C7171u/16V

C7181u/16V

HDMI_Audio_L

1B1

VCC

Pin6(1B1) HDMI

Audio L input

P701

GND

2B0

AUDIO IN

PC_Line_R

PC_Line_L

HDMI_Audio_R

2B1

Pin1(2B0)

PC Audio R

input

Pin4(2B1) HDMI

Audio R input

FSA2257

Line_R

VCC5V

Pin10,13 Connect to MCU GPIO

to Switch PC_HDMI_Audio

PC_HDMI_SWT

InnoLux

Document Number :

SIZE :

Custom

APPRO BY :

CHECK BY :

doc

TITLE :

Audio_ BV223W

2007-12-12

DATE :

SHEET

DRAWN BY :

Rev :

V01

Pin Define

IF CN102

CON CN301

CON CN302

KEYPD CON

1x8p 1.25mm180degree

2x4p 2.0mm 180degree

2x4p 2.0mm 90degree

CN302

CN301

Auto

RIGHT&Left

E-color

LED_A

LED_G

GND

POWER

2x4P 2.0mm

From IF BD

2x4P 2.0mm

To Keypad

InnoLux

Document Number :

SIZE :

APPRO BY :

CHECK BY :

doc

TITLE :

Connector_ BV223W

2007-12-12

DATE :

SHEET

DRAWN BY :

Rev :

V01

Acer

Acer –LCD-B223W

7.0 Assembly and Disassembly

Description

Sequence

Item

Photo

Procedures

P/N

(1).Take panel out of box and place it on

the foam.

(2).Tear open the PE bag and put it in

the designated carton.

(3).Place panel on the foam like the

attached picture.

Remark:Do not touch the lamp cord and

place the surface of panel downsides on

the cushion.

LCP

22"MT220WW0

1-V0-

G1,AM2200001

001(INNO

Place

panel

631102220091R

HRN ASSY

2x4P to 8P

245mm

430300801690R

1.Check if the keypad and relevent wire

you choose are OK.

2.Insert the wire into the keypad like the

Picture

Insert

Keypay's

wrie

UL1571#28,RO

1.Check if there is any lacquer missed or

sctratch happened to the front bezel.

2.Insert the fixed keypad into the front

bezel as picture

ASSY,BEZEL,F

RONT,(silver),LE

22D3

Fix front

bezel

714030015400R

Acer

Acer –LCD-B223W

Assembly and Disassembly (continue)

1.Reverse the panel by 180 degree,put

the surface of panel upsides and insert

front bezel in the panel.

2.Reverse the panel by 180 degree using

both hands,put the surface of panel

downsides and make sure FFC interface

is closer to operator.

3.Paste tinfoil on the position which refers

to attached picture,in order to cover the

gap in the panel completely.

Assemble

front

ASSY,BEZEL,F

RONT,(silver),LE

22D3

714030015400R

bezel

Remark:Make sure the fixed job is

finished properly and lamp wire is closer

to right hand;Make the tinfoil smooth in

the corner of panel.

(1).Insert FFC wire into its relevant

interface of mainboard properly like

attached picture1.

(2).Insert the short keypad into its

relevant interface like picture1.

(2).Put the fixed mainboard in the right

position.

PCBA,I/F

Fix

mainboar

BOARD(V0,EME

A,W/O),LE22D3

-612 R

791411300600R

Fix

chassis

&powebo

ard

Place the chassis on the cushion after

check,like the attached Picture1.

ASSY,CHASSIS

,W/DVI,LE22D3

701000007010R

Acer

Acer –LCD-B223W

Assembly and Disassembly (continue)

Fix

chassis

&powebo

ard

PCBA,P/I

Insert powerboard into the designated

location of chassis ,like the attached

Picture

BOARD,W/O

SPK,LE22D2-

612 ROHS

791411401600R

Connect

mainboar

d&powerb

oard

Connent powerboard with the relevant

PIN in the mainboard like the attached

Picture

Twist

PCBA

screw

SCREW,P,CRO

SS,W/WAS,M3*

6,Zn-Cc

Handle electric opener and one pcs of

M3*6 screw

509146306200R

Acer

Acer –LCD-B223W

Assembly and Disassembly (continue)

Twist

PCBA

screw

Fix 3 pcs of screws separately on the

poweboard and mainboard like the

attached Picture1

SCREW,P,CRO

SS,W/WAS,M3*

6,Zn-Cc

509146306200R

S10

Twist

screw for

ground-

wire

Paste FFC wire on the disignated

location like the attached Picture

S11

(1). Handle hexagonal screws and

electric opener

(2). Twist screw in the interface like the

attached Picture1.

(3). Place cushion on the designated

location after iron frame is taken away.

Twist

Hexagonal

screws

S12

Acer

Acer –LCD-B223W

Assembly and Disassembly (continue)

Thread lamp wire into the relevant hole of

chassis like the attached Picture

S13

S14

S15

S16

Fix chassis

1)Fix chassis on the back of panel and

front bezel

2)Put lamp wire and FFC wire in order as

picture

Fix chassis

1.Tear off the adhensive tape of FFC

wire;

2.Insert FFC wire into the interface of

panel

3.Put FFC wire in order and paste them

on the panel

4.Fix chassis on the back of panel

Insert FFC

cable

1)Insert 4pcs light wire into the relevant

position

2) put the balance light wire to the

position as picture

Insert light

wire

Acer

Acer –LCD-B223W

Assembly and Disassembly (continue)

make sure the

1)Insert keypad wire into the relevant PIN

red cabel in left

in the keypad

Insert

keypad

Cable

2)Fix button on the relevant position of

（

S17

assemble

3)Confirm if keypad is inserted properly

（

and make sure the red cable in left

Fix back

cover

Check if back cover is fixed properly

S18

Use 4pcs screw fix stand on the back of

assemble like attached Picture

S19

Fix stand

HP Hewlett Packard Hewlett Packard Computer Monitor LA1905WG User Manual
GE General Electric Cooktop JVB67 User Manual
GE 26995 User Manual
Fujitsu Siemens Computers Fujitsu Siemens SCENICVIEW P17 2 User Manual
Fairchild SEMICONDUCTOR RC5050 User Manual
Cisco Systems 5515 X User Manual
Cisco Systems 2500 User Manual
Bloomfield WVOC 2HSG User Manual
Asus Crosshair V Formula Z Crosshair V Formula User Manual
AOC Computer Monitor E2343F2K User Manual