User’s manual
EL42108
5.8GHzcordlesstelephone/
answering system with
caller ID/call waiting
ANNC.
RECORD
REMOVE
You must install and charge
the battery before using
the telephone.
See page 9
for easy instructions.
STOP!
If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL)
through your telephone lines, you must install a DSL filter between the
telephone base and the telephone wall jack (page 6). The filter will prevent
noise and caller ID problems caused by DSL interference. Please contact your
DSL service provider for more information about DSL filters.
Your product may be shipped with a protective sticker covering the handset
or telephone base display - remove it before use.
For customer service or product information, visit our website at
1 (866) 288-4268.
CAUTION: To reduce the risk of fire or injury to persons or damage to
the telephone, read and follow these instructions carefully:
• Use only the supplied rechargeable battery or replacement battery (part
number 89-1332-00-00) or equivalent. To order a replacement battery,
3111. In Canada, dial 1 (866) 288-4268.
• Do not dispose of the battery in a fire. Like other batteries of this type,
it could explode if burned. Check with local codes for special disposal
instructions.
• Do not open or mutilate the battery. Released electrolyte is corrosive and
may cause damage to the eyes or skin. It may be toxic if swallowed.
• Exercise care in handling batteries in order not to create a short circuit. Do
not allow conductive materials such as rings, bracelets, or keys to touch
the battery. The battery or conductor may overheat and cause harm.
• Charge the battery provided with or identified for use with this product
only in accordance with the instructions and limitations specified in this
manual.
• Observe proper polarity orientation between the battery and battery
charger.
• Do not disassemble your telephone. There are no user-serviceable parts
inside. Refer to qualified service personnel for servicing.
Parts checklist
Save your sales receipt and original packaging in the event warranty service is
necessary.
Your telephone contains the following items:
User’s manual
Quick start guide
EL42108
EL42108
5.8GHzcordlesstelephone/
answering system with
caller ID/call waiting
5.8GHzcordlesstelephone/
answering system with
caller ID/call waiting
ANNC.
RECORD
ANNC.
RECORD
REMOVE
REMOVE
REMOVE
User's manual
Quick start guide
Cordless handset
ANNC.
RECORD
Telephone base
Battery for cordless
handset
Battery compartment
cover
Telephone line cord
Power adapter for telephone
base
User’s manual
EL42108
5.8 GHz cordless telephone/
answering system with
caller ID/call waiting
ANNC.
RECORD
REMOVE
Table of contents
Getting started
Appendix A
Quick reference guide
Screen icons, indicator lights
& tones..............................................39
handset..................................................2
telephone base..................................3
Handset main menu..............................4
Telephone base installation...............5
Installation options................................7
Battery installation & charging..............9
Appendix B
Handset display screen
messages..............................................40
Appendix C
Troubleshooting.....................................41
Telephone operation
Appendix D
Important safety instructions..........49
Settings......................................................11
Basic operation......................................14
Options while on calls........................17
Appendix E
FCC part 68 & ACTA............................52
Directory
Appendix F
FCC part 15..............................................54
Directory....................................................18
Speed dial.................................................19
New directory entries.........................20
Directory search....................................22
To change or dial entries.....................23
Appendix G
Limited warranty...................................55
Appendix H
Technical specifications.....................58
Caller ID
Caller ID history.....................................24
Review the Caller ID history............27
Delete call history entries................28
Add entries to the directory............29
Appendix I
Index............................................................59
Answering system
Answering system.................................30
Day & time announcements............31
Outgoing announcements................32
Changing feature options.................33
Message playback.................................34
Record & play memos........................35
Message counter displays................36
Answering system mode...................37
Remote access.......................................38
1
Getting started
Quick reference guide - handset
CHARGE
MENU/SELECT
Press to display menu.
Press to store a
The light is on when
a cordless handset is
properly positioned to
charge in the telephone
base.
programming option.
CID/-VOLUME
DIR /VOLUME+
When in a menu, press
to scroll down. When
the phone is not in use,
press to display caller ID
history entries (page 27).
While entering names
or numbers, press to
move the cursor to the
left. During a call, press
to decrease listening
volume.
When in a menu, press
to scroll up. When the
phone is not in use, press
to display directory entries
(page 22). While entering
names, press to advance
the cursor. During a call,
press to increase listening
volume.
OFF/CLEAR
During a call, press to
hang up (page 14). While
using menus, press to
cancel an operation, or
exit the menu.
PHONE/FLASH
Press to make or answer
a call. During a call, press
to receive an incoming
call if call waiting is
activated (page 17).
REDIAL/PAUSE
When the phone is not
in use, press repeatedly
to display the last five
numbers called (page 15).
While dialing or entering
numbers to the directory,
press to insert a four-
second dialing pause
CHAN/REMOVE
When on a call, press to
scan for a clearer channel
when there is static or
interference on the line
REMOVE
(page 17). When in caller
ID mode, press to delete
the displayed caller ID
entry (page 28), or press
and hold to delete all
caller ID entries when the
phone is not in use
(page 28).
(page 21).
MUTE
While on a call, press to
mute the microphone.
Press again to resume your
conversation (page 17).
2
Getting started
Quick reference guide - telephone base
IN USE
• On steady when a handset is
in use.
• Flashes quickly while an
incoming call is ringing.
HANDSET LOCATOR
Press to make the handset
beep when a handset is not on
the telephone base (page 16).
ANNC.
RECORD
Answering System
Functions
PLAY/STOP
Press to start or stop
MESSAGE COUNTER
message playback
(page 34).
Number of messages
(or during playback,
message number
SKIP
currently playing).
Press to skip message
(page 34).
REPEAT
DELETE
Press to repeat message;
press twice to play
previous message
(page 34).
Press to delete message
currently playing; press
twice to delete all old
messages when the
phone is not in use
(page 34).
ON/OFF
Press to turn answering
system on or off
(page 37).
ANNC.
RECORD
VOL
Press to adjust playback
volume (page 34).
CLOCK
Press to review or set
clock (page 31).
RECORD
Press to record a
memo (page 35) or
after pressing ANNC.
to record an outgoing
announcement
ANNC.
SETUP
Press to review or
record announcement;
press again to quit
(page 32).
Press to review or
change answering
system options
(page 33).
(page 32).
3
Getting started
Handset main menu
To enter the main menu:
1. Press MENU/SELECT when the handset is not in use.
2. Press CID or DIR
to select a handset feature menu, then press
MENU/SELECT to enter that menu.
To return to the idle mode, press OFF/CLEAR.
DIRECTORY allows you
to store and search for
names and numbers
(page 18).
SPEED DIAL allows
you to store or dial a
number in a speed dial
location (page 19).
RINGER allows you to
set the ringer
(page 12).
DIRECTORY
SPEED DIAL
RINGER: 1
RINGER VOL allows
you to set the ringer
volume (page 12).
DATE/TIME allows you
to set the date and
time (page 13).
DIAL MODE allows you
to set tone or pulse
dialing (page 11).
DIAL MODE: TONE
RINGER VOL: HI
DATE/TIME
HOME AREA CODE
allows you to set your
home area code
(page 13).
LANGUAGE allows you
to set your handset
display language
(page 11).
LANGUAGE
HOME AREA CODE
4
Getting started
Telephone base installation
The telephone base can be placed on a flat surface or vertically mounted
on the wall (page 7). For optimum range and better reception, place the
telephone base in a central and open location.
Avoid placing the telephone base too close to:
• Communication devices such as: personal computers, computer routers,
television sets, VCRs, wireless routers (wireless broadband, wi-fi, or 802.11)
or other cordless telephones.
• Excessive heat sources.
• Noise sources such as a window with traffic outside, motors, microwave
ovens, refrigerators, or fluorescent lighting.
• Excessive dust sources such as a workshop or garage.
• Excessive moisture.
• Extremely low temperature.
• Mechanical vibration or shock such as on top of the washing machine or
work bench.
5
Getting started
Telephone base installation
If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL)
through your telephone lines, you must install a DSL filter between the
telephone base and the telephone wall jack. The filter will prevent noise
and caller ID problems caused by DSL interference. Please contact your DSL
service provider for more information about DSL filters.
Install the telephone base as shown below.
1. Plug the small
end of the power
adapter into the
power jack on
the underside of
the telephone
base.
2. Plug one end of
the telephone
line cord into the
telephone jack
on the underside
of the telephone
base.
3. Route cords
through slots.
DSL filter
5. Plug the
(available from your DSL Internet
provider)
large end of
the power
4. Plug the other
end of the
adapter into an
electrical outlet
not connected
to a wall switch.
Telephone line cord
telephone line
cord into a
telephone jack.
NOTES:
1. Use only the power adapter supplied with this product or equivalent. To order a replacement power
In Canada, dial 1 (866) 288-4268.
2. This power adapter is intended to be correctly oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or
cabinet outlet.
6
Getting started
Installation options
The telephone base is designed for both desktop installation and wall mount
installation. If wall mounting is desired, a telephone outlet wall mounting
plate with mounting studs is required. This mounting plate is available for
purchase at many hardware or consumer electronics retailers and may require
professional installation.
Desktop to wall mount installation
1. Plug the telephone line cord
and power adapter into the
telephone base. Bundle the
telephone line cord and route
cords through the slots, then
secure with a twist tie.
2. Plug the power adapter and
telephone line cord into the wall
outlets, then align the mounting
studs on the telephone outlet
plate with the mounting holes
on the telephone base.
1
3. Place the telephone base
mounting holes just above the
mounting studs, then slide the
telephone base down until it is
secure.
2
7
Getting started
Installation options
Wall mount to desktop installation
To change the telephone base from the wall mount position to desktop
position, make sure that you first unplug the power adapter and telephone
line cord from the wall outlets before you begin.
1
2
1. Slide the telephone base
upwards, then pull the
telephone base away from the
wall off of the mounting studs.
2. Unplug the power adapter and
the telephone line cord from
the electrical outlet and the
telephone jack.
3. Plug the telephone line cord
into the telephone base and
telephone wall jack, then plug
the power adapter plug into the
telephone base and a power
outlet not connected to a wall
switch.
8
Getting started
Battery installation & charging
Install the battery as shown below. After installing the battery, you can
make and receive short calls, but replace the handset in the telephone
base when not in use. For optimal performance, charge the handset battery
for at least 16 hours before use. When fully charged, the handset battery
provides approximately five hours of talk time or six days of standby time.
If the handset has not been used for a long time or if the battery inside is
completely depleted, put it on the telephone base for recharging.
Step 1
Step 2
Step 3
Insert the battery plug as
indicated, making sure that
it matches the color-coded
label inside the battery
compartment.
Place the battery
and wires inside the
compartment.
Slide the battery
compartment cover
up until it clicks.
Step 4
CHARGE
Charge the handset, by placing the
handset face up in the telephone
base. The CHARGE light on the
handset should be on as soon as
the handset is properly placed on
the telephone base.
light
ANNC.
RECORD
REMOVE
9
Getting started
Battery installation & charging
Low battery indicator
LOW BATTERY
Return the handset to the telephone base to recharge
when this symbol flashes and the handset beeps or when
the handset screen displays LOW BATTERY.
10:08AM
02/14
To replace the battery, Press the tab and slide the
battery compartment cover downwards. Lift out the old
battery and disconnect it from the handset. Follow the
instructions on the previous page to install and charge
the new battery.
IMPORTANT INFORMATION
Use only the supplied rechargeable battery, replacement battery (part number 89-1332-00-00) or
equivalent. To order a replacement battery, visit our website at
1 (866) 288-4268.
10
Telephone operation
Settings
To customize how the handset works:
1. Press MENU/SELECT in the idle mode to enter
the handset main menu.
2. Use CID or DIR
to scroll to the desired
feature.
3. Press MENU/SELECT to select the feature.
To stop at any time, press OFF/CLEAR.
Language
To change the language to Espanol, or Francais:
1. Press MENU/SELECT in the idle mode to enter
the handset main menu
.
LANGUAGE
2. Press CID or DIR
until the screen displays
LANGUAGE.
3. Press MENU/SELECT. The current setting is
flashing.
4. Press CID or DIR
to choose ENGLISH,
FRANCAIS, or ESPANOL.
5. Press MENU/SELECT to save your selection and
return to the main menu.
Dial mode
The dial mode defaults to tone. If you do not have
touch tone service, you will need to change the
setting to pulse:
1. Press MENU/SELECT in the idle mode to enter
the handset main menu.
DIAL MODE: TONE
2. Press CID or DIR until the screen displays
DIAL MODE: and the current setting.
3. Press MENU/SELECT. The current setting is
flashing.
4. Press CID or DIR
to display TONE or
PULSE.
5. Press MENU/SELECT to save your selection and
return to the main menu.
11
Telephone operation
Settings
Ringer volume
You can set your handset to a ringer volume level
of HI, LOW, or OFF. To set the ringer level:
1. Press MENU/SELECT in the idle mode to enter
RINGER VOL: LOW
the handset main menu.
2. Press CID or DIR
until the screen displays
RINGER VOL: and the current setting.
3. Press MENU/SELECT. The current setting is
flashing. You will also hear the current volume
level.
NOTES:
4. Press CID or DIR
to choose the desired
1. If you choose OFF, the
cordless handset ringer
will be turned off, and the
screen will display RINGER
volume level. You will hear a sample of each
ringer volume.
OFF and
when the
5. Press MENU/SELECT to save your selection and
cordless handset is idle
(not in use). If there are
unreviewed calls, the screen
will display XX MISSED
CALLS and instead of
return to the main menu.
-OR-
1. Press and hold CID or DIR
when the
RINGER OFF and
.
cordless handset is idle (not in use).
2. When the volume level is at
the HI or OFF setting, you
will hear two alert beeps.
2. Press CID or DIR
to choose the desired
volume level. You will hear a sample of each
ringer volume.
3. Press MENU/SELECT to save your selection and
return to the main menu.
Ringer
1. Press MENU/SELECT in the idle mode to enter
the handset main menu.
2. Press CID or DIR
until the screen displays
RINGER: and the current setting.
RINGER: 1
3. Press MENU/SELECT. The current setting is
flashing. You also hear the current ringer
sound.
4. Press CID or DIR
to display 1, 2, 3 or 4.
You will hear a sample of each ringer sound.
5. Press MENU/SELECT to choose the displayed
ringer sound and return to the main menu.
12
Telephone operation
Settings
Date & time
To manually set the date and time on the handset
display:
DATE/TIME
1. Press MENU/SELECT in the idle mode to enter
the handset main menu.
2. Press CID or DIR
until the screen displays
DATE/TIME.
NOTES:
3. Press MENU/SELECT to view or set date and
1. You can choose to set
the time manually, or
you can allow it to
time.
4. Press CID or DIR
to change the month
be set automatically
in the date and time line at the bottom of the
display, then press MENU/SELECT.
with incoming caller ID
information. The time will
be set automatically only if
you subscribe to caller ID
service provided by your
local telephone company
(page 24). The date and
time for the answering
machine need to be set
separately (page 31).
5. Repeat step four to set the date, hour, minute,
and AM/PM.
6. Press MENU/SELECT to save selection and
return to the main menu.
Home area code
2. Caller ID will not set the
year. See page 31 for
instructions on how to set
the year.
If you dial seven digits to make a local call (area
code not required), you can program your area
code into the telephone as the home area code.
After setting, if you receive a call from within
your home area code, the screen will display
the telephone number with the home area code.
However, the home area code will not be shown
when reviewing the caller ID history.
HOME AREA CODE
To program the home area code:
1. Press MENU/SEL when the phone is not in use
NOTE: If, in the future,
your telephone service
provider requires you to
dial 10 digits to make a
local call (area code +
phone number), program
your home area code to
000.
to enter the handset main menu.
2. Press CID or DIR
until the screen displays
HOME AREA CODE.
3. Press MENU/SEL.
4. Press the dial pad keys to enter a three-digit
home area code.
5. Press MENU/SEL to save and return to the main
menu.
Please refer page 27 for other dialing options.
13
Telephone operation
Basic operation
Make & end a call
To make a call:
Elapsed
time
• Press PHONE/FLASH, then enter the
telephone number.
PHONE
0:00:30
To end a call:
• Press OFF/CLEAR or return the handset in the
telephone base.
On-hook dialing (predialing)
• Enter the telephone number, then press
PHONE/FLASH. To make corrections as you
enter the number, press CID or DIR
to
REMOVE
move to the digit you want to erase, then press
CHAN/REMOVE.
The screen displays the elapsed time of the
current call (in hours, minutes and seconds).
Answer a call
To answer a call:
• Press PHONE/FLASH.
-OR-
• Press any keys (except CID, DIR
and
OFF/CLEAR).
To end a call:
• Press OFF/CLEAR or return the handset in the
telephone base.
NOTE: During a call, pressing
PHONE/FLASH to access
service from your local telephone service provider will
not affect the elapsed time.
14
Telephone operation
Basic operation
Redial
While the phone is not in use, press
REDIAL/PAUSE repeatedly to display the last
five numbers called (up to 30 digits). To dial the
number displayed, press PHONE/FLASH. Or, after
pressing PHONE/FLASH, press REDIAL/PAUSE to
call the last dialed number.
To delete the redial memory, press REDIAL/PAUSE,
then press CHAN/REMOVE to delete one by one.
Ringer
silenced
Press OFF/CLEAR to exit.
REMOVE
NOTE: While on a call, press REDIAL/PAUSE to review
the last number dialed. You cannot delete from redial
while on a call.
Temporary ringer silencing
While the telephone is ringing, press OFF/CLEAR
to silence the ringer temporarily. This will silence
the ringer without disconnecting the call. You can
answer the call or let the caller leave a message.
The next incoming call will ring normally.
Auto off
A call will be ended automatically when you put
the handset in the telephone base.
15
Telephone operation
Basic operation
Handset locator
The handset locator feature is useful if you
misplace the handset.
ANNC.
RECORD
To start the paging tone:
• Press HANDSET LOCATOR at the telephone
base. This starts the paging tone at the handset
for 60 seconds to help you locate the handset.
NOTE: If the handset is charging in the telephone base,
pressing HANDSET LOCATOR does not generate a
paging tone.
** PAGING **
To stop the paging tone:
• Press HANDSET LOCATOR on the telephone
base.
-OR-
• Place the cordless handset in the telephone
base.
NOTE: When paging, pressing
OFF/CLEAR on the
REMOVE
cordless handset will cancel the page of the handset.
The handset locator feature will not be cancelled.
16
Telephone operation
Options while on calls
Volume control
While on a call, press CID/-VOLUME to decrease
the volume, press DIR /VOLUME+ to increase
the volume.
VOLUME
Call waiting
If you subscribe to call waiting service with your
local telephone company, there will be a beep if
there is an incoming call while you are already on
a call. Press PHONE/FLASH to put your current
call on hold and take the new call. Press
PHONE/FLASH anytime to switch back and forth
between calls.
Mute
REMOVE
The mute function allows you to silence the
microphone. You can hear the caller, but the
caller will not be able to hear you.
To mute the call:
• Press MUTE to silence the microphone. When
mute is on, MIC MUTED will display temporarily
on the handset screen and MUTE will be shown
until mute is turned off.
To un-mute the call:
• Press MUTE again and resume speaking.
When mute is turned off, MIC ON will display
temporarily on the handset screen.
Temporary tone dialing
If dial pulse (rotary) is selected, you can switch
to touch tone dialing during a call by pressing
TONE . This can be useful if it is necessary to
*
send tone signals for access to answering systems
or long-distance services.
REMOVE
After you hang up or press PHONE/FLASH
(to receive a call waiting call), the telephone
automatically returns to dial pulse (rotary) service.
Channel selection
During a call, if you hear clicks and pops, or if the
speech sometimes fades, press CHAN/REMOVE on
the handset to scan for a clearer radio channel
between cordless handset and base.
17
Directory
Directory
Memory capacity
The handset directory can store up to 30 entries
(including nine speed dial entries). Each entry can
contain a number up to 24 digits, and a name up
to 14 characters. A convenient search feature can
help you find and dial numbers quickly (page 22).
PAT WILLIAMS
5551234
Timeouts & error messages
If you pause for too long while creating an entry,
the telephone will time out and you will have to
begin again.
If all memory locations are in use, the screen
will display MEMORY FULL. You will not be able
to store a new number until an existing one is
deleted.
REMOVE
MEMORY FULL
18
Directory
Speed dial
You can enter nine speed dial numbers of up to
24 digits. Each number is stored in a speed dial
location (1-9).
The nine speed dial numbers on the handset will
be automatically added to the handset directory.
You can also make existing directory entries into
speed dial entries (page 23).
NOTE: The speed dial
feature occupies up to
nine of the thirty
memory locations in the
directory. For example, if
there are only five speed
dial entries, then up to
25 entries can be stored
in the directory. If there
are already 30 entries in
the directory, no new
directory and speed dial
entries can be stored in
memory until some of
the existing ones are
deleted.
Enter a speed dial number
1. Press MENU/SELECT.
2. Press CID or DIR
until the screen displays
SPEED DIAL.
3. Press MENU/SELECT.
DIRECTORY
4. Press a dial pad key (1-9) to select a speed dial
location.
5. Enter a name up to 14 characters (page 20),
then press MENU/SELECT.
SPEED DIAL
6. Enter a telephone number up to 24 digits (page
21), then press MENU/SELECT.
7. Choose distinctive ringing (N or Y) by pressing
CID or DIR . If you choose yes (and if you
have caller ID service), a different ringing style
will alert you when this person calls.
ENTER 1-9
8. Press MENU/SELECT to store the number. You
will hear a confirmation tone.
ENTER NAME
01
Call a speed dial number
To use speed dialing, press and hold a dial pad
key (1-9) to display the number and name stored
in that speed dial location, then press
PHONE/FLASH to dial.
Edit or delete a speed dial number
Press and hold a dial pad key (1-9) to display
the entry you want. Press MENU/SELECT, then
NOTE: You can convert
any directory entry into
a speed dial entry
(page 23).
press CID or DIR
until the option you want is
displayed (page 23).
19
Directory
New directory entries
Create & store a directory entry
NOTE: If all memory
locations are in use, an
error tone will sound
when you attempt to
enter a number. This
means the memory
is full, and you will
not be able to store a
new number until you
delete an existing one.
1. Press MENU/SELECT in the idle mode to enter
the handset main menu.
2. Press MENU/SELECT again to enter the
DIRECTORY menu.
3. Enter the name when prompted.
• Use the dial pad to enter a name (up to 14
characters). See the chart below.
- Press DIR
to move the cursor to the
DIRECTORY
right. Press CID to move the cursor to
the left.
- Press DIR
or CID to move to the
character you want to delete, then press
CHAN/REMOVE to erase the letter.
ENTER NAME
4. When finished entering the name, press
MENU/SELECT.
PAT JOHNSON_
20
Directory
New directory entries
5. Enter the telephone number when prompted.
• Use the dial pad to enter up to 24 digits.
- Press DIR
to move the cursor to the
ENTER NUMBER
right. Press CID to move the cursor to
the left.
- Press DIR
or CID to move to the digit
you want to delete, then press
CHAN/REMOVE to erase the digit.
- Press REDIAL/PAUSE to enter a four-
PAT JOHNSON
5556789_
second dialing pause. A P will be inserted.
-OR-
• Copy the last redial number by pressing
REDIAL/PAUSE. Press MENU/SELECT to copy
the number.
DISTINCT RING? N
5556789
6. When finished entering the telephone number,
press MENU/SELECT.
7. Select desired ring pattern.
• Press CID or DIR
to select Y (to assign
a distinctive ring tone) or N (for a normal
ring pattern). If you choose yes (and you
have caller ID service), a different ringer
style will alert you when this person calls.
8. Press MENU/SELECT to choose the desired
option and store this entry in the directory.
NOTE: A D appears in the display of each entry that has
been assigned a distinctive ring.
21
Directory
Directory search
Review directory entries
1. Press DIR when the phone is not in use.
DIRECTORY EMPTY will be displayed if there
are no directory entries in the handset.
2. Press CID or DIR
to browse through the
directory.
DIRECTORY
3. Press OFF/CLEAR to exit the directory.
NOTES:
1. When reviewing directory entries, all entries (including
those in the directory and in the speed dial) are displayed
in alphabetical order. The entries in the speed dial are
identified by its speed dial number (01-09) in the lower
right corner of the screen (page 19).
ADAM
5551234
2. A D appears in the display of each entry that has been
assigned a distinctive ring (page 21).
BETH
5554321
Search by name
To shorten your search, press DIR then use the
telephone dial pad keys to enter the first letter of
a name, then press DIR to scroll forward until
you find the desired name.
-OR-
If you have more than one name entry that begins
with the same letter, it is necessary to scroll
through all the names beginning with that letter
before seeing names that begin with the next
letter.
JOHN
5550123
Press dial pad keys once for the first letter, twice
for the second, three times for the third.
For example, if you have name entries JENNIFER,
KEVIN and LINDA in your directory, pressing the
dial pad key 5 (JKL) once will show JENNIFER,
twice KEVIN, three times LINDA.
NOTE: When searching alphabetically and you press a
dial pad button, if there are no entries beginning with
the letters on that button, the handset will show NO
DATA.
22
Directory
To change or dial entries
When any entry is displayed, press MENU/SELECT
to see options. Press CID or DIR
to highlight
the option you want (blinking text), then press
MENU/SELECT again to select it.
Edit an entry
When EDIT is blinking, press MENU/SELECT. You
can change the name and number (or distinctive
ring setting on the cordless handset) by following
the steps described on pages 20-21.
DIRECTORY
Delete an entry
ADAM
Press CID or DIR
until DEL is blinking, then
5551234
press MENU/SELECT to display a confirmation
screen of ERASE NO YES.
You can press CID or DIR
to alternate
between NO or YES to determine:
SPEED EDIT DEL
5551234
• When YES is blinking, press MENU/SELECT to
delete the entry.
• When NO is blinking, press MENU/SELECT to
cancel the procedure.
SPEED EDIT DEL
5551234
Change a directory entry into a speed dial entry
Press CID or DIR
until SPEED is blinking,
press MENU/SELECT, then press a memory
location (1-9) to transfer this entry to your speed
dial directory.
SPEED EDIT DEL
5551234
NOTE: If you use a memory location that is already
assigned to a different entry in the directory the original
entry will remain in the directory, but will no longer be a
speed dial number.
Display dial
When any directory entry is displayed, press
PHONE/FLASH to dial the displayed number.
23
Caller ID
Caller ID history
About caller ID with call waiting
This product has a caller ID function with call
waiting feature which works with service from
your local telephone company.
Caller ID with call waiting lets you see the name
and telephone number of the caller before
answering the telephone, even while on another
call.
CHRISTINE SMITH
908-555-0100
10:08AM
02/14
It may be necessary to change your telephone
service to use this feature. Contact your telephone
company if:
• You have both caller ID and call waiting, but
as separate services (you may need combined
service).
REMOVE
• You have only caller ID service, or only call
waiting service.
• You do not have any caller ID or call waiting
services.
This product can be used with regular caller ID
service, or this product’s other features can be
used without subscribing to either caller ID or
combined caller ID with call waiting service.
There are fees for caller ID services. In addition,
services may not be available in all areas.
Depending on your service, you may see the
caller’s number or the caller’s name and number.
This product can provide information only if both
you and the caller are in areas offering caller
ID service and if both telephone companies use
compatible equipment. The time and date are sent
by the telephone company along with the call
information.
24
Caller ID
Caller ID history
How caller ID works
If you subscribe to caller ID service provided by
your local telephone company, information about
each caller will be displayed between the first and
second ring.
Call number in
CHRISTINE SMITH
908-555-0100
Caller’s name
CHRISTINE SMITH
the call history
908-555-0100
Caller’s phone
number
02
10:08AM
02/14
Appears when
the call is
10:08AM
02/14
missed and
unreviewed
Time of call Date of call
Information about the last 30 incoming calls is
stored in the call history. You can review the call
history to find out who has called, return the
call, or copy the caller’s name and number into
directory.
REMOVE
When the call history is full, the oldest entry
is deleted to make room for new incoming call
information.
NOTES:
1. Caller ID features will work
only if both you and the
caller are in areas offering
caller ID service, and if both
telephone companies use
compatible equipment.
If you answer a call before the information
appears on the screen, it will not be saved in the
call history.
2. The number shown by
your caller ID will be in
the format sent by the
About names
Names of callers will be displayed only if the
information is provided by your local telephone
company.
telephone company. The
telephone company usually
delivers 10-digit telephone
numbers (area code plus
telephone number). If the
telephone number of the
person calling does not
exactly match a number in
your directory, the name
will appear as delivered by
the telephone company. For
example if the telephone
company includes the area
code and the directory
If the incoming telephone number exactly matches
a telephone number in your directory, the name
that appears on the screen will match the
corresponding name in your directory.
For example: If Christine Smith calls, her name will
appear as CHRIS if this is how you entered it into
your directory.
number does not, the name
will appear as delivered by
the telephone company.
25
Caller ID
Caller ID history
There are also occasions when other information
or no information is displayed for various reasons:
On-screen message Reason
PRIVATE NAME
Caller prefers to remain
anonymous.
PRIVATE CALLER
Caller's name and telephone
number not revealed at caller's
request.
CHRISTINE SMITH
908-555-0100
UNKNOWN NAME
UNKNOWN CALLER
Your local telephone company is
unable to determine the caller's
name.
10:08AM
02/14
Your local telephone company is
unable to determine the caller's
name and telephone number.
Calls from other countries may
also generate this message.
REMOVE
Missed (new) call indicator
When the handset is not in use and has calls that
have not been reviewed, its screen will show XX
MISSED CALLS.
Any entries which have not been reviewed will be
counted as MISSED CALLS when the telephone is
idle. Each time a call history entry marked NEW
is reviewed, the number of missed calls decreases
by one.
02 MISSED CALLS
10:08AM
02/14
Pat Williams
If there are too many missed calls and you don’t
want to review them one by one, but still want to
keep them in the call history, press and hold
OFF/CLEAR for two seconds when the handset
is idle. All the entries in the caller ID history will
be considered old (have been reviewed), and the
missed calls counter is reset to 0.
555-1234
NEW
01
AM
10:08
02/14
26
Caller ID
Review the caller ID history
The call history displays the caller ID in reverse
chronological order, with the latest one (the one
with the highest number) first.
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
When the telephone is not in use, press CID to
display information about the most recent caller.
CHRIS WILLIAMS
908-555-1234
Review your call history
02
10:08AM
02/14
Press CID to scroll backward (display older calls)
or DIR
to scroll forward (display newer calls).
The highest call number is the most recent call
received.
PHONE
9085551234
0:00:10
Each unreviewed caller ID entry in the call history
will be designated NEW until you have reviewed
it. After all calls have been reviewed, NEW will
disappear from the screen.
PAT JOHNSON
908-555-0100
03
Make a call from caller ID history
10:08AM
02/14
Press PHONE/FLASH to call the number currently
displayed.
- OR-
PAT JOHNSON
908-555-0100
NOTE: If the number displayed is not in the correct
format, see Dialing options for detail.
03
10:08AM
02/14
Dialing options
Caller ID numbers may appear with an area code
that may not be required for local calls.
PAT JOHNSON
1-908-555-0100
03
If the number displayed is not in the correct
format, you can change how it is dialed. Press
# repeatedly to see dialing options. With each
button press, a new option will be displayed. Press
PHONE/FLASH to dial when the number appears
in the proper format for your area.
10:08AM
02/14
PAT JOHNSON
555-0100
03
10:08AM
02/14
The various dialing options are:
908-555-0100
1-908-555-0100
555-0100
PAT JOHNSON
1-555-0100
03
10:08AM
02/14
1-555-0100
27
Caller ID
Delete call history entries
PAT JOHNSON
908-555-0100
Delete a single call history entry
03
10:08AM
02/14
Press CID to display the latest caller ID listing.
Use the CID or DIR
keys to find the entry
you want to delete, then press CHAN/REMOVE.
When the entry is deleted, the next oldest record
is displayed.
CHRIS WILLIAMS
908-555-1234
02
10:08AM
02/14
Delete all call history entries
MARK CLAYTON
908-555-5678
To clear your call history completely, press and
hold CHAN/REMOVE while the telephone is idle
(not in use). This will display a confirmation screen
asking if you want to erase all entries in the caller
ID history. If you select yes, the call history will
be cleared and the screen will return to normal
standby display, and the missed calls counter is
reset to 0.
01
10:08AM
02/14
- OR-
27 MISSED CALLS
10:08AM
02/14
NOTE: When there are already 30 entries in the caller ID
memory, the next incoming call will automatically cause
the oldest entry to be deleted from the caller ID memory.
ERASE ALL? N Y
ERASE ALL? N Y
10:08AM
02/14
28
Caller ID
Add entries to the directory
PAT JOHNSON
908-555-0100
Add entries to the directory
03
While you have a caller ID entry displayed, follow
the steps below to enter it into your telephone
directory.
10:08AM
02/14
DIAL PROGRAM
908-555-0100
1. Press CID when the phone is not in use. CID
EMPTY will be displayed if there are no call
history entries in the handset.
03
10:08AM
02/14
2. Press MENU/SELECT, then press CID or DIR
PAT JOHNSON
9085550100
until PROGRAM is flashing.
3. Press MENU/SELECT and edit the name and
number as desired.
PAT JOHNSON
9085550100_
4. Press MENU/SELECT, then press CID or DIR
to alternate between Y and N. If you choose
Y (and if you have caller ID service), a distinct
ring tone will alert you when this person calls.
DISTINCT RING? N
9085550100
5. Press MENU/SELECT to confirm, the entry is
added to the phone directory.
NOTE: The entry copied to your telephone directory
remains in the call history until deleted.
PAT JOHNSON
908-555-0100
03
10:08AM
02/14
29
Answering system
Answering system
Message capacity
The answering system can record up to 95
messages depending on the length of each
message. Individual messages can be up to
four minutes. The maximum record time can be
more than 11 minutes. The actual recording time
depends on individual message characteristics.
Messages will remain available for replay until you
delete them.
Message counter
Number of messages (or
during playback, message
number currently playing).
Voice prompts
Each time you press any answering system key,
the answering system uses voice prompts to
guide you.
Press to start or
stop message
playback (page 34).
Press to repeat
message; press
twice to play
previous message
(page 34).
Press to skip a
message (page 34).
Press to turn
answering system
on or off (page 37).
Press to delete
message currently
playing; press twice
to delete all old
messages when the
phone is not in use
(page 34).
Press to review
time and day or set
clock (page 31).
ANNC.
RECORD
Press repeatedly to
hear setup options
(page 33).
Press to adjust
playback volume
(page 34).
Press to review
or record
announcement;
press again to quit
(page 32).
Press to record a
memo (page 35)
or after pressing
ANNC. to record
an outgoing
announcement
(page 32).
30
Answering system
Day & time announcements
Check day & time
You can press CLOCK at any time to hear the
current day and time without changing it.
ANNC.
RECORD
Set day & time
Before playing each message, the answering
system announces the date and time when the
message was received.
Follow the steps below to set the day, time and
year, so that messages are dated correctly. Each
time you press SKIP or REPEAT, the day, hour,
minute or year increases or decreases by one.
Press and hold SKIP or REPEAT to increase or
decrease the minutes or year by increments of 10.
When you hear the correct setting, press CLOCK
to move to the next setting.
NOTES:
1. If the clock was not set
when the message was
recorded, the system will
announce "Time and day
not set."
2. Caller ID provides the
time and date. Set the
year so that the day
1. Press CLOCK, The system will announce the
current clock setting, then announces “To set
the clock, press CLOCK.”
of the week can be
calculated from the caller
ID information. The time
will be set automatically
only if you subscribe to
caller ID service provided
by your local telephone
company (page 25).
2. Press CLOCK, The system will announce the
current day setting, then announces “To change
the day, press SKIP or REPEAT, to change
the hour, press CLOCK.”
3. Press CLOCK, The system will announce the
current hour setting, and then announce “To
change the hour, press SKIP or REPEAT, to
change the minute, press CLOCK.”
4. Press CLOCK, The system will announce the
current minute setting, and then announce “To
change the minute, press SKIP or REPEAT, to
change the year, press CLOCK.”
5. Press CLOCK, The system will announce the
current year setting, and then announce “To
change the year, press SKIP or REPEAT, press
CLOCK when you are done.”
6. Press CLOCK. The system announces the
current clock setting.
31
Answering system
Outgoing announcements
The outgoing announcement is the message
callers hear when calls are answered by the
answering system.
The telephone is factory set with an
announcement. If the telephone is set up to
record messages, it answers calls with “Hello.
Please leave a message after the tone.” You
can use this announcement, or replace it with a
recording of your own voice.
Elapsed
ANNC.
RECORD
recording
time (in
seconds).
Play your outgoing announcement
1. Press ANNC., you will hear "Announcement.
Press PLAY or press RECORD."
2. Press
PLAY/STOP. You will hear the
outgoing announcement.
3. Press ANNC. to exit the announcement menu.
Record your outgoing announcement
NOTE: While recording,
the elapsed time (in
seconds) will be shown
in the message window.
You can record an
announcement up to 90
seconds long.
Announcements shorter
than two seconds long
will not be recorded.
1. Press ANNC., you will hear "Announcement.
Press PLAY or press RECORD."
2. Press RECORD and begin speaking after
hearing "Record after the tone. Press STOP
when you are done." Speak facing the
telephone base from about nine inches away.
3. Press
PLAY/STOP when you are done. Your
recorded announcement will be played back.
4. Press ANNC. to exit the announcement menu.
Delete your outgoing announcement
1. Press ANNC., you will hear “Announcement.
Press PLAY or press RECORD.”
2. Press
PLAY/STOP to begin playback.
3. Press DELETE during playback to delete your
announcement.
4. Press ANNC. to exit the announcement menu.
When your announcement is deleted, calls will be
answered with the factory set announcement.
32
Answering system
Changing feature options
You can set and change the answering system
features described below:
1. Press SETUP repeatedly until you hear the
ANNC.
RECORD
feature you want to modify.
2. Press SKIP or REPEAT to change the
setting.
3. Press SETUP to set your selection and move to
the next menu option.
4. Press
PLAY/STOP to confirm the setting and
exit the menu.
Feature options (Default settings underlined)
System announces:
Feature description:
NOTES:
"Number of rings," current
setting, then "To change
the setting press SKIP
or REPEAT; to continue
setup, press SETUP."
Choose number of rings before
the system answers a call. When
toll saver is active, the system
answers after two rings if you
have new messages, and after
four rings if you have no new
messages. If you are making a
long distance call to retrieve
messages, you may disconnect
your call after three rings so that
there will be no long distance
charge incurred.
1. The message alert tone
will beep only if all the
conditions below are met:
Answering system is on;
Message alert tone setting
is on;
Options: 2/4/6/toll saver
There are new messages.
2. Press any base key to
temporarily silence the
message alert tone. If you
press DELETE twice when
the phone is not in use, you
will delete all old messages
and the message alert tone
will be temporarily silenced.
The message alert tone will
be re-activated with the
next incoming message.
“Base ringer,” current
setting, then “To change
the setting, press SKIP or
REPEAT; tocontinue setup,
press SETUP.”
Choose the telephone base
ringer volume between high and
low level, or turn the telephone
base ringer off.
Options: high/low/off
"Remote access code,"
current setting, then
"To change the setting
press SKIP or REPEAT;
to continue setup, press
SETUP."
Select a two-digit number (10-
99) for remote access from
another telephone (page 38).
NOTE: Press and hold SKIP
or REPEAT to increase or
decrease the remote access
code number by 10.
Options: (select a two-digit
code) 19
"Message alert tone,"
current setting, then
"To change the setting,
press SKIP or REPEAT;
to continue setup, press
SETUP."
When on, the telephone beeps
every 10 seconds when there are
new messages.
Options: on/off
33
Answering system
Number of messages (or during
playback, message number
currently playing).
Message playback
Press
PLAY/STOP to listen to messages. The
system announces the number of messages, then
begins playback.
If you have new messages, you will hear only the
new messages (oldest first). If there are no new
messages, the system will playback all messages
(oldest first).
ANNC.
RECORD
Press
PLAY/STOP
Announcements
to begin or end message
playback.
• When playback begins, you will hear the total
number of messages.
Press
PLAY/STOP
1.
• Before each message, you will hear the day
and time it was received.
“You have [XX] new
messages and [XX]
old messages.”
• After playing all new messages, you will hear
"End of new messages." You will hear “End
of messages” after the answering system has
finished the playback of all messages. If the
system has less than five minutes of recording
time left, you will hear the estimated time
remaining.
Message playback begins.
See options at right.
Press
PLAY/STOP to
2.
end message playback.
Options during playback
NOTES:
1. If F and the total message
number is flashing in the
message window, memory
is full. You will have to
delete some messages
before new ones can be
received.
• Press VOL button to adjust the speaker
volume.
• Press SKIP to skip to next message.
• Press REPEAT to repeat the message
currently playing. Press twice to hear previous
message.
2. The maximum record time
can be more than 11
minutes.
• Press DELETE to delete the message being
3. If you receive calls when
the memory is full, the
telephone will ring 10
times, then answer and
announce “Memory is
full, enter the remote
access code.”
played back.
• Press
PLAY/STOP to stop playback.
Delete all messages
To delete all old messages, press DELETE twice
when the phone is not in use.
4. New (unheard) messages
cannot be deleted.
34
Answering system
Record & play memos
Memos are messages you record yourself. They
are saved, played back and deleted exactly like
incoming messages. You can record a memo as
a reminder to yourself, or leave a message for
someone else if other members of your household
are using the answering system.
Elapsed
recording
time
ANNC.
RECORD
(seconds).
Record a memo
Press RECORD
1.
2.
Press RECORD. Elapsed time (in seconds) is shown
in the message window as you record. You can
record a memo up to four minutes. Memos less
than one second will not be saved.
“Record after the
tone. Press STOP
when you are done.”
Speak into microphone.
Press
PLAY/STOP to stop recording.
ANNC.
RECORD
Play back a memo
Press
PLAY/STOP to hear messages and memos
(see page 34 for other options).
Microphone
Press PLAY/STOP
“Recorded, beep.”
3.
35
Answering system
Message counter displays
When the answering system is idle, the message
counter displays the total number of answering
system messages. See the list below for
explanations of other displays in this counter.
ANNC.
RECORD
Message counter
Message counter displays
0
No messages.
0 (flashing)
The clock needs to be set (page 31).
1-95
Total number of messages and memos,
or message number currently playing.
1-95 (flashing)
Total number of messages and memos.
The number flashes when there are new
(unreviewed) messages.
If the telephone loses power, after power
is restored, the number in the message
counter will flash (even if you have only
old messages) to indicate the clock needs
to be set.
10-99
Current remote access code while setting
(page 33).
1-99 (counting)
Elapsed time while recording a memo
(page 35) or announcement up to 90
seconds (page 32).
99 (flashing)
F (flashing)
--
Memo recording time has exceeded the
maximum counter capacity of 99 seconds.
Memory is full. Messages must be deleted
before new messages can be received.
System is answering a call, being accessed
remotely, or the clock is being set, or a
handset is on a call
-- (flashing)
System is being setup or initialized.
2, 4, 6, S
Current number of rings-to-answer while
setting this feature (page 33).
1-8
Displayed for two seconds while telephone
base speaker volume is being adjusted.
HI, LO, OF
Displayed for two seconds while telephone
base ringer volume is being adjusted.
36
Answering system
Answering system mode
The answering system’s default factory setting is
ON in order to answer and record messages. You
can turn the answering system off, but if you do
so, the answering system will not answer calls or
record incoming messages.
ANNC.
RECORD
Turn the answering system off
Press ON/OFF until
the system announces
“Calls will not be
answered.”
1.
2.
Press ON/OFF until you hear “Calls will not be
answered” and a confirmation beep. The
ON/OFF will be turned off.
"Beep."
The system has been
turned off.
NOTE: If the answering system is off and someone calls,
the telephone will ring 10 times then answer and
announce “Please enter your remote access code.” Enter
your remote access code to enter remote access mode
(page 38). If you do not enter the correct remote access
code, the call will be ended automatically.
-OR-
Turn the answering system on
Press ON/OFF until the
system announces “Calls
will be answered.”
1.
2.
Press ON/OFF until you hear “Calls will be
answered” then a beep to confirm the ON setting.
The ON/OFF light will be turned on.
"Beep."
The system has been
turned on.
Call screening
If the answering system is on and the telephone
base volume is not set to off, you will hear the
announcement and the incoming message when a
call comes in.
Call intercept
While you are call screening, you can intercept
the call by pressing PHONE/FLASH on the
handset.
37
Answering system
Remote access
A two digit security code is required to access
your answering system from any touch-tone
telephone. This code is 19 by default, see
Changing feature options (page 33) to change it.
Dial your telephone number
from any touch-tone
telephone.
1.
2.
When the system answers,
enter two digit remote
access code (19 unless
you have changed it).
Press to hear all messages.
Press to hear new messages.
Play all messages
1
Play new messages
Enter remote commands
(see list at right).
3.
4.
2
Delete the message
Press once during playback to
delete current message. Press
twice to delete all old messages.
3
33
Hang up to end the call
and save all undeleted
messages.
Press during the caller’s
message to repeat the message.
Press during the beginning of
the day and time announcement
to go back to the previous
message.
Repeat or go back
4
Press to stop any operation (stop
playback, stop recording).
Stop
5
Press to skip the current
message and advance to next
message.
Skip to next message
6
Press *7, wait for the beep, then
begin speaking. Press 5 to stop
recording and hear the playback
of new announcement.
Record announcement
*7 to begin recording
5 to stop recording
Help menu
Press to hear list of features &
commands.
*5
NOTE: If you pause
for more than four
seconds during
Press to turn off answering
system. Incoming calls will no
longer be answered.
Turn system off
0
remote access, you
will hear a help menu
listing all features
and commands. If
there is no command
entered for another
15 seconds, the call
will end automatically.
If off, system will answer after
10 rings. Enter your access
code, then press 0 to turn the
answering system on.
Turn system on
0
Exit
8
Press 8 or hang up to end the
remote access call.
38
Appendix A
Screen icons, indicator lights & tones
Screen icons & alert tones
Screen icons
Microphone is muted.
06 MISSED CALLS
Ringer off.
02
10:08AM
02/14
Low battery (flashing); place handset in telephone base to
recharge.
Missed and unreviewed calls.
REMOVE
Handset alert tones
Two short beeps
The volume level is at the maximum or minimum setting.
Low battery warning.
Double beep every
minute when on a call
Four beeps
Out of range when on the line.
Error tone.
Five beeps
Confirmation tone
Command completed successfully.
Telephone base tones
One beep every
10 seconds
Message alert.
A series of beeps
Press VOL keys while the volume level is already at the maximum or
minimum setting.
Indicator lights
CHARGE
The light is on when
the cordless handset
is properly positioned
to charge in the
telephone base.
IN USE
•
On steady when the
handset is in use.
•
Flashes quickly while
an incoming call is
ringing.
Large lighted
display
ANNC.
RECORD
ON/OFF
Lighted dial
pad
The light is on when the
answering system is on and
ready to receive messages.
REMOVE
39
Appendix B
Handset display screen messages
Screen display messages
CONNECTING...
The cordless handset is waiting
for a dial tone.
** RINGING **
** PAGING **
There is an incoming call.
CONNECTING .. .
The cordless handset locator
has been activated (the cordless
handset beeps to help you locate
it).
Cordless handset battery is low.
Place the cordless handset in
base to charge the battery (it may
take up to 10 minutes).
LOW BATTERY
SCANNING...
Cordless handset is scanning for
a clear channel to improve sound
quality.
REMOVE
There are missed and unreviewed
calls in your call history.
XX MISSED CALLS
RINGER OFF
The cordless handset ringer is
turned off.
The handset directory is full.
MEMORY FULL
MIC MUTED
The handset microphone is
temporarily muted.
The handset microphone is no
longer muted.
MIC ON
Another telephone on the same
line is in use.
PARALLEL SET ON
Cordless handsets cannot
communicate with the base.
Check base power, or move
closer.
POWER FAILURE
followed by
OR OUT OF RANGE
40
Appendix C
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below.
call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
My telephone
does not work
at all.
• Make sure the battery is installed and charged correctly
(page 9). For optimum daily performance, return the
cordless handset to the telephone base after use.
• Make sure the power adapter is securely plugged into an
outlet not connected to a wall switch.
• Make sure the telephone line cord is plugged firmly into
the telephone base and the modular wall jack.
• Unplug the telephone’s electrical power. Wait for
approximately 15 seconds, then plug it back in. Allow
up to one minute for the cordless handset and base to
synchronize.
• Charge the battery in the cordless handset for at least
16 hours.
• Remove and re-insert the battery. If that still does not
work, it may be necessary to purchase a new battery.
• Disconnect the telephone base from the modular jack
and plug in a working telephone. If this telephone does
not work, the problem is probably in the wiring or the
local service. Call the local telephone company.
• Place the handset in the telephone base for recharging.
The CHARGE light on the handset should be on as soon
as the handset is properly placed on the telephone
base. If the handset has not been used for a long
time or if the battery inside is completely depleted.
Depending on the strength of the battery in the handset,
it may take up to 10 minutes before the handset screen
shows NEEDS CHARGING.
LOW BATTERY
is displayed on
screen.
• Remove and re-install the battery and use it normally
until fully discharged, then recharge the handset on the
telephone base for 16 hours.
• If the above measures do not correct the problem, the
battery may need to be replaced.
41
Appendix C
Troubleshooting
• Make sure the handset is placed in the telephone base
The battery
does not
charge in the
handset or the
handset battery
does not
correctly. The CHARGE light on the handset should be
on.
• If the cordless handset is in the telephone base, but the
CHARGE light is not on, refer to The CHARGE light is
off in this section.
accept charge.
• It may be necessary to purchase a new battery. Please
refer to the Batteries section of this user’s manual.
• The telephone might be malfunctioning. Please refer to
the Limited warranty section of this user’s manual for
further instruction.
• Clean the metallic charging contacts on the cordless
handset and telephone base each month using a pencil
eraser or a dry non-abrasive fabric.
The CHARGE
light is off.
• Make sure the power adapter and telephone line cords
are plugged in correctly and securely.
• Unplug the power adapter. Wait for 15 seconds before
plugging it back in. Allow up to one minute for the
cordless handset and telephone base to reset.
• The telephone might be malfunctioning. Please refer to
the Limited warranty section of this user’s manual for
further instruction.
There is no dial • First, try all the suggestions in My telephone does not
tone.
work at all, on the previous page.
• Move the cordless handset closer to the telephone base.
It might be out of range.
• The telephone line cord might be malfunctioning. Try
installing a new telephone line cord.
• Disconnect the telephone base from the telephone jack
and connect a different telephone. If there is no dial
tone on that telephone either, the problem is in your
wiring or local service. Contact your local telephone
company.
42
Appendix C
Troubleshooting
• Make sure the ringer is on (page 12).
The telephone
does not ring
when there is
an incoming
call.
• Make sure the telephone line cord and power adapter
are plugged in properly (page 6).
• The cordless handset may be too far from the telephone
base. Move it closer to the telephone base.
• There may be too many extension telephones on
the telephone line to allow all of them to ring
simultaneously. Try unplugging some of them.
• If the other telephones in your home are having the
same problem, the problem is in the wiring or local
service. Contact the local telephone company (charges
may apply).
• Other electronic products can cause interference to your
cordless telephone. Try installing your telephone as far
away as possible from the following electronic devices:
wireless routers, radios, radio towers, pager towers,
cellular telephones, digital telephones, intercoms, room
monitors, televisions, VCRs, personal computers, kitchen
appliances, and other cordless telephones.
• Test a working telephone at the same telephone jack. If
another telephone has the same problem, the problem
is in the telephone jack. Contact your local telephone
company (charges may apply).
• The telephone line cord might be malfunctioning. Try
installing a new telephone line cord.
• Re-install the battery and place the cordless handset in
the telephone base.
• Wait for the cordless handset to synchronize with the
telephone base. Allow up to one minute for this to take
place.
My phone rings
but when I try
to answer the
call the handset
screen shows
• The cordless handset may be too far from the telephone
base. Move closer to the telephone base and try to
answer the call.
CONNECTING…
43
Appendix C
Troubleshooting
I cannot dial
out.
• First, try all the suggestions in The telephone does not
ring when there is an incoming call, on the previous
page.
• Make sure there is a dial tone before dialing. It is
normal if the cordless handset takes a second or two to
synchronize with the telephone before producing a dial
tone. Wait an extra second before dialing.
• Make sure the telephone is set to the correct dial mode
(pulse dial or tone dial) for the service in your area.
Refer to the Dial mode section of this user’s manual
(page 11) to set the dial mode.
• If the other telephones in your home are having the same
problem, the problem is in the wiring or local service.
Contact your local telephone company (charges may apply).
• Eliminate any background noise. Noise from a television,
radio, or other appliances may cause the telephone
to not dial out properly. If you cannot eliminate the
background noise, first try muting the cordless handset
before dialing, or dialing from another room in your
home with less background noise.
There is noise
or interference
during a
• The handset may be out of range. Move it closer to the
telephone base.
telephone
conversation.
My calls fade
out or cut in
and out when
I am using
• Appliances or other cordless telephones plugged into
the same circuit as the telephone base can cause
interference. Try moving the appliance or telephone
base to another outlet.
the cordless
handset.
• Other electronic products can cause interference to
your cordless telephone. Try installing your telephone
as far away as possible from the following electronic
devices: wireless routers, radios, radio towers, pager
towers, cellular telephones, digital telephones,
intercoms, room monitors, televisions, VCRs, personal
computers, kitchen appliances, and other cordless
telephones.
44
Appendix C
Troubleshooting
• Microwave ovens operate on the same frequency
as your telephone. It is normal to experience static
on your telephone while the microwave oven is
operating. Do not install this telephone in the same
outlet or near a microwave oven.
• If your telephone is plugged in with a modem or
a surge protector, plug the telephone (or modem/
surge protector) into a different location. If this
doesn't solve the problem, re-locate your telephone
or modem farther apart from each other, or use a
different surge protector.
• The layout of your home or office might be limiting
the operating range. Try moving the telephone base
to another location, preferably a higher location for
better reception.
• Disconnect the telephone base from the modular
jack and plug in a corded telephone. If calls are still
not clear, the problem is probably in the wiring or
local service. Contact your local service company
(charges may apply).
• Select channels four through 10 for your router
(refer to the user’s manual of your router for more
information).
• If the other telephones in your home are having
the same problem, the problem is in the wiring or
local service. Contact the local telephone company
(charges may apply).
• If you subscribe to high-speed Internet service
(Digital Subscriber Line - DSL) through your
telephone line, you must install a DSL filter between
the telephone base and the telephone wall jack
(page 6). The filter will prevent noise and caller ID
problems caused by DSL interference. Please contact
your DSL service provider for more information
about DSL filters.
I hear other
calls when using
the telephone.
• Disconnect the telephone base from the telephone
jack. Plug in a different telephone. If you still hear
other calls, the problem is probably in the wiring or
local service. Call your local telephone company.
45
Appendix C
Troubleshooting
• Caller ID is a subscription service. You must subscribe to
My caller ID
features are
not working
properly.
this service from your local telephone company for this
feature to work on your telephone.
• The caller may not be calling from an area that supports
caller ID.
• Both you and the caller’s telephone companies must use
equipment compatible with caller ID service.
• If you subscribe to high-speed Internet service (Digital
Subscriber Line - DSL) through your telephone line, you
must install a DSL filter between the telephone base
and the telephone wall jack (see page 6). The filter will
prevent noise and caller ID problems caused by DSL
interference. Please contact your DSL service provider
for more information about DSL filters.
• Make sure you subscribe to caller ID with call waiting
features services provided by the local telephone
company.
The system
does not receive
caller ID or the
system does not
display caller
ID during call
waiting.
• The caller may not be calling from an area that supports
caller ID.
• Both you and the caller’s telephone companies must use
equipment compatible with caller ID service.
• If you subscribe to high-speed Internet service (Digital
Subscriber Line - DSL) through your telephone line, you
must install a DSL filter between the telephone base
and the telephone wall jack (see page 6). The filter will
prevent noise and caller ID problems caused by DSL
interference. Please contact your DSL service provider
for more information about DSL filters.
“Time and
day not set”
prompts.
• You need to set the answering system clock (page 31).
The
• When recording the announcement, make sure you
speak in a normal tone of voice about nine inches from
the telephone base.
• Make sure there is no background noise (television,
music, traffic, etc.) when recording.
announcement
message is not
clear.
46
Appendix C
Troubleshooting
• Make sure the answering system is on. When the
The answering
system does
not answer
after the
correct number
of rings.
answering system is on, the red light on the ON/OFF
key should be lit.
• If toll saver is activated, the number of rings changes to
two when there are new messages waiting (page 33).
• If the memory is full or if the answering system is off,
the system will answer after 10 rings. If the memory is
full, you need to delete some old messages in order to
make room for new messages.
• In some cases, the answering system may be affected
by the ringing system used by the local telephone
company.
• Make sure the answering system is on.
The answering
system does
not record
• If the memory is full the system will answer after 10
rings and announce “Memory is full. Enter the remote
access code.” You need to delete some old messages in
order to make room for new messages.
messages.
The messages
on the
answering
system are
incomplete.
• If a caller reaches the maximum recording time of four
minutes, for each message, the system will disconnect
and part of the message may be lost.
• If the caller pauses for more than seven seconds, the
system stops recording and disconnects the call.
• If the memory on the system becomes full during a
message, the system stops recording and disconnects
the call.
• If the caller’s voice is very soft, the system may stop
recording and disconnect the call.
The messages
on the system
are difficult to
hear.
• Press VOL on the telephone base to increase the
speaker volume.
47
Appendix C
Troubleshooting
• Make sure your remote access code is correct (page 38).
The answering
system does
not respond
to remote
• Make sure you are calling from a touch-tone telephone.
When dialing a number, you should hear tones. If you
hear clicks, then it is not a touch-tone telephone and
cannot activate the answering system.
commands.
• The answering system may not detect the remote
access code when your announcement is playing. Wait
until the announcement is over before entering the
code.
• There may be interference on the telephone line you are
using. Press the dial pad keys firmly when dialing.
Common cure
for electronic
equipment.
• If the telephone is not responding normally, try putting
the cordless handset in the telephone base. If it does
not seem to respond, try the following (in the order
listed):
1. Disconnect the power to the telephone base.
2. Disconnect the battery on the cordless handset.
3. Wait a few minutes before connecting power to the
telephone base.
4. Re-install the battery and place the cordless handset
into the telephone base .
5. Wait for the cordless handset to synchronize its
connection with the telephone base. Allow up to one
minute for this to take place.
48
Appendix D
Important safety instructions
This symbol is to alert you to important operating or servicing
instructions that may appear in this user’s manual. Always follow basic safety
precautions when using this product to reduce the risk of injury, fire, or
electric shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe all
markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight
chance of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak. If you suspect a gas
leak, report it immediately, but use a telephone away from the area where
gas is leaking. If this product is a cordless model, make sure the telephone
base is also away from the area.
• Do not use this product near water, or when you are wet. For example,
do not use it in a wet basement or shower, or next to a swimming pool,
bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays
for cleaning. If the product comes in contact with any liquids, unplug any
line or power cord immediately. Do not plug the product back in until it
has dried thoroughly.
• Install this product in a protected location where no one can trip over
any line or power cords. Protect cords from damage or abrasion.
• If this product does not operate normally, read Troubleshooting in
this user’s manual. If you cannot solve the problem, or if the product
is damaged, refer to the limited warranty. Do not open this product
except as may be directed in your user’s manual. Opening the product or
reassembling it incorrectly may expose you to hazardous voltages or other
risks.
• If this product has user-replaceable batteries, replace batteries only
as described in your user’s manual. Do not burn or puncture batteries
— they contain caustic chemicals.
• If this product has a three-prong (grounding) plug or a polarized plug
with one wide prong, it may not fit in non-polarized outlets. Do not defeat
the purpose of these plugs. If they do not fit in your outlet, the outlet
should be replaced by an electrician.
CAUTION: Use only the power adapter provided with this product. To
call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.
49
Appendix D
Important safety instructions
Especially about cordless telephones
• Privacy: The same features that make a cordless telephone convenient
create some limitations. Telephone calls are transmitted between the
telephone base and handset by radio waves, so there is a possibility that
your cordless telephone conversations could be intercepted by radio
receiving equipment within range of the cordless handset. For this reason,
you should not think of cordless telephone conversations as being as
private as those on corded telephones.
• Electrical power: The telephone base of this cordless telephone must be
connected to a working electrical outlet. The electrical outlet should not be
controlled by a wall switch. Calls cannot be made from the handset if the
telephone base is unplugged or switched off, or if the electrical power
is interrupted.
• Power adapter: This power adapter is intended to be plugged into a
vertical wall outlet or a floor outlet.
• Potential TV interference: Some cordless telephones operate at
frequencies that may cause interference to TVs and VCRs. To minimize or
prevent such interference, do not place the telephone base of the cordless
telephone near or on top of a TV or VCR. If interference is experienced,
moving the cordless telephone farther away from the TV or VCR will often
reduce or eliminate the interference.
• Rechargeable batteries: This product contains either Nickel-Cadmium
or Nickel-Metal Hydride rechargeable batteries. Exercise care in handling
batteries in order not to short the battery with conducting material such
as rings, bracelets, and keys. The battery or conductor may overheat and
cause harm. Observe proper polarity between the battery and the battery
charger.
• Nickel-cadmium rechargeable batteries: Must be recycled or disposed of
properly. Do not dispose of in household garbage. Do not burn or puncture.
Like other batteries of this type, if burned or punctured, they could release
caustic material which could cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an
industry program to collect and recycle nickel-cadmium rechargeable batteries when
taken out of service within the United States. These batteries may be taken to a
participating local retailer of replacement batteries or recycling center. Or you may
call 1 (800) 8-BATTERY for locations accepting spent nickel-cadmium batteries.
50
Appendix D
Important safety instructions
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led
a multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR had recommended to physicians that:
Pacemaker patients
• Should keep wireless telephones at least six inches from the pacemaker.
• Should NOT place wireless telephones directly over the pacemaker, such
as in a breast pocket, when it is turned ON.
• Should use the wireless telephone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from
other persons using wireless telephones.
Especially about telephones answering systems
Two-way recording: This telephone does not sound warning beeps to let
the other party know that the call is being recorded. To ensure that you are
in compliance with any federal or state regulations regarding recording a
telephone call, you should start the recording process and then inform the
other party that you are recording the call.
SAVE THESE INSTRUCTIONS
51
Appendix E
FCC part 68 & ACTA
This equipment complies with Part 68 of the FCC rules and with technical
requirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among
other things, a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. An RJ11 jack should normally be used
for connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices
you may connect to your telephone line and still have them ring when you
are called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0) or less. For
more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially
wired alarm dialing equipment connected to your telephone line, ensure
the connection of this equipment does not disable your alarm equipment. If
you have questions about what will disable alarm equipment, consult your
telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular
jack until the problem has been corrected. Repairs to this telephone
equipment can only be made by the manufacturer or its authorized agents.
For repair procedures, follow the instructions outlined under the Limited
Warranty.
If this equipment is causing harm to the telephone network, the telephone
company may temporarily discontinue your telephone service. The telephone
company is required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible. You will be
given the opportunity to correct the problem and the telephone company is
required to inform you of your right to file a complaint with the FCC. Your
telephone company may make changes in its facilities, equipment, operation,
or procedures that could affect the proper functioning of this product. The
telephone company is required to notify you if such changes are planned.
52
Appendix E
FCC part 68 & ACTA
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
If this product has memory dialing locations, you may choose to store
emergency telephone numbers (e.g., police, fire, medical) in these locations. If
you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging
up.
Perform such activities in off-peak hours, such as early morning or late
evening.
Industry Canada
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference,
including interference that may cause undesired operation.
The term ‘’IC:‘’ before the certification/registration number only signifies that
the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
The REN is an indication of the maximum number of devices allowed to be
connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that
the sum of the RENs of all the devices does not exceed five.
This product meets the applicable Industry Canada technical specifications.
53
Appendix F
FCC part 15
This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of
radio frequency energy that can be safely absorbed by a user or bystander
according to the intended usage of the product. This product has been tested
and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base shall be installed and used
such that parts of the user’s body other than the hands are maintained at a
distance of approximately 20 cm (8 inches) or more. If you choose to use a
clipping device, please make sure to only use the supplied AT&T belt clip.
This Class B digital apparatus complies with Canadian ICES-003.
54
Appendix G
Limited warranty
The AT&T brand is used under license - any repair, replacement or warranty
service, and all questions about this product should be directed to: In the
United States of America, visit our website at
dial 1 (866) 288-4268.
1. What does this limited warranty cover?
The manufacturer of this AT&T-branded product warrants to the holder of
a valid proof of purchase (“CONSUMER” or “you”) that the product and all
accessories provided in the sales package (“PRODUCT”) are free from defects
in material and workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with the PRODUCT
operating instructions. This limited warranty extends only to the CONSUMER
for products purchased and used in the United States of America and Canada.
2. What will be done if the PRODUCT is not free from defects in materials
and workmanship during the limited warranty period (“materially defective
PRODUCT”)?
During the limited warranty period, the manufacturer’s authorized service
representative will repair or replace at the manufacturer’s option, without
charge, a materially defective PRODUCT. If the manufacturer repairs the
PRODUCT, they may use new or refurbished replacement parts. If the
manufacturer chooses to replace the PRODUCT, they may replace it
with a new or refurbished PRODUCT of the same or similar design. The
manufacturer will retain defective parts, modules, or equipment. Repair
or replacement of the PRODUCT, at the manufacturer’s option, is your
exclusive remedy. The manufacturer will return repaired or replacement
products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the PRODUCT extends for ONE (1) YEAR
from the date of purchase. If the manufacturer repairs or replaces a
materially defective PRODUCT under the terms of this limited warranty,
this limited warranty also applies to repaired or replacement PRODUCT for
a period of either (a) 90 days from the date the repaired or replacement
PRODUCT is shipped to you or (b) the time remaining on the original one-
year limited warranty; whichever is longer.
55
Appendix G
Limited warranty
4. What is not covered by this limited warranty?
This limited warranty does not cover:
• PRODUCT that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water, or other liquid intrusion; or
• PRODUCT that has been damaged due to repair, alteration, or
modification by anyone other than an authorized service representative
of the manufacturer; or
• PRODUCT to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
• PRODUCT to the extent that the problem is caused by use with non-
AT&T accessories; or
• PRODUCT whose warranty/quality stickers, PRODUCT serial number
plates or electronic serial numbers have been removed, altered or
rendered illegible; or
• PRODUCT purchased, used, serviced, or shipped for repair from outside
the United States of America or Canada, or used for commercial or
institutional purposes (including but not limited to products used for
rental purposes); or
• PRODUCT returned without valid proof of purchase (see item 6 below);
or
• Charges for installation or setup, adjustment of customer controls, and
installation or repair of systems outside the telephone.
5. How do you get warranty service?
To obtain warranty service in the United States of America, call
1 (800) 222-3111; In Canada, please dial 1 (866) 288-4268.
NOTE: Before calling for service, please review the user’s manual - a check
of the PRODUCT controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or
damage during transit and transportation and are responsible for delivery
or handling charges incurred in the transport of the PRODUCT(s) to
the service location. The manufacturer will return repaired or replaced
PRODUCT under this limited warranty. Transportation, delivery or handling
charges are prepaid. The manufacturer assumes no risk for damage or loss
of the PRODUCT in transit. If the PRODUCT failure is not covered by this
limited warranty, or proof of purchase does not meet the terms of this
limited warranty, the manufacturer will notify you and will request that
you authorize the cost of repair prior to any further repair activity. You
must pay for the cost of repair and return shipping costs for the repair of
products that are not covered by this limited warranty.
56
Appendix G
Limited warranty
6. What must you return with the PRODUCT to get warranty service?
You must:
a. Return the entire original package and contents including the PRODUCT
to the service location along with a description of the malfunction or
difficulty; and
b. Include “valid proof of purchase” (sales receipt) identifying the PRODUCT
purchased (PRODUCT model) and the date of purchase or receipt; and
c. Provide your name, complete and correct mailing address, and telephone
number.
7. Other limitations
This warranty is the complete and exclusive agreement between you and
the manufacturer of this AT&T branded PRODUCT. It supersedes all other
written or oral communications related to this PRODUCT. The manufacturer
provides no other warranties for this PRODUCT. The warranty exclusively
describes all of the manufacturer’s responsibilities regarding the PRODUCT.
There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state or
province to province.
Limitations: Implied warranties, including those of fitness for a particular
purpose and merchantability (an unwritten warranty that the PRODUCT is
fit for ordinary use) are limited to one year from date of purchase. Some
states/provinces do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. In no event shall the
manufacturer be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue,
inability to use the PRODUCT or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting from the use
of this PRODUCT. Some states/provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
Please retain your original sales receipt as
proof of purchase.
57
Appendix H
Technical specifications
RF frequency band
(handset to telephone base)
5857.2 MHz — 5865.9 MHz
RF frequency band
(telephone base to handset)
912.75 MHz — 917.10 MHz
Channels
30
Modulation
FM
Operating temperature
32°F — 122°F
0°C — 50°C
Telephone base voltage
(AC voltage, 60Hz)
104 — 129Vrms
Telephone base voltage
(AC adapter output)
AC7.5V @350mA
Handset voltage
DC3.1 — 4.3V 400mAh
3.6V 400mAh Ni-Cd
Replacement battery
5.8 GHz analog technology
Dual band transmission combines the best of 5.8 GHz and 900MHz analog
technologies to provide quality performance and complete signal coverage for
a standard home, while not interfering with wireless routers.
Telephone operating range
This cordless telephone operates with the maximum power allowed by
the Federal Communications Commission (FCC). Even so, the handset and
telephone base can communicate over only a certain distance - which can
vary with the locations of the telephone base and handset, the weather, the
layout, and the construction of your home or office.
58
Appendix I
Index
A
I
Alert tones, 39
Incoming call history, 27
Indicator lights, 39
Answer a call, 14
Answering system, 30-38
M
B
Make a call, 14
Message playback, 34
Missed calls, 26
Mute, 17
Battery charging, 9
Battery installation, 9
Battery low, 10
P
C
Power adapter, 6
Predialing, 14
Call waiting, 17
Caller ID, 24
Q
add entries to the directory, 29
delete entries, 28
dial entries, 27
Quick reference guide, 2-3
R
Channel, 17
Call screening, 37
Call intercept, 37
Recharging, 9
Redial, 15
Ringer silencing, 15
Ringer, 12
Ringer volume, 12
D
Delete call history entries, 28
Delete redial entries, 15
Dialing,
S
Screen display messages, 40
Search for names, 22
Speed dial, 19
directory dialing, 23
from a CID record, 27
mode, 11
T
Directory, 18
Technical specifications, 58
Temporary tone dialing, 17
Troubleshooting, 41-48
dial number, 23
edit entries, 23
search, 22
DSL filter, 6
V
Volume control,
Ringer, 12
Telephone, 17
Voice prompts, 30
E
Elapsed time, 14
End a call, 14
F
Flash (switchhook flash), 17
H
Handset locator, 16
Home area code, 13
59
Remote access wallet card
Use the wallet card below to help you remember commands to control your
answering system from any touch tone telephone.
Cut along dotted line.
Call your phone number, then
enter your two-digit access code
(preset to 19).
Action
Remote command
Play all messages..................1
Play new messages...............2
Delete the message..............3
Delete all old messages.....33
Repeat or go back.................4
Stop...............................................5
Help menu.................................*5
Fold here.
Skip the message...................6
Record announcement........*7
Turn system off or on..........0
End remote access call ......8 (or hang up)
EL42108
5.8 GHz cordless telephone/answering system
with caller ID/call waiting
© 2008 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P.
d/b/a AT&T Intellectual Property licensed to Advanced American Telephones.
Printed in China.
© 2008 Advanced American Telephones. All rights reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a
AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China.
Issue 9 AT&T 09/08.
|