User’s Manual
5.8 GHz Cordless
Telephone/Answering
System E5943B/
E5944B
with Caller ID/CallWaiting
IMPORTANT
Information about caller ID with call waiting
This product has a caller ID with call waiting feature that works
with service from your local telephone service provider.
Caller ID with call waiting lets you see who is calling before you
answer the phone, even when you’re on another call.
You may need to change your phone service to use this
feature. Contact your telephone service provider if:
• you have both caller ID and call waiting, but as separate ser-
vices (you may need combined service).
• you have only caller ID service, or only call waiting service.
• you don’t subscribe to any caller ID or call waiting services.
You can use this product with regular caller ID service, and you
can use this product’s other features without subscribing to
either caller ID or combined caller ID with call waiting service.
There are fees for caller ID services, and they may not be
available in all areas.
Depending on your service, you may see the caller’s number, or the caller’s name and
number. This product can provide information only if both you and the caller are in areas
offering caller ID service, and if both telephone companies use compatible equipment.
The time and date are sent by the service provider along with the call information.
Copyright © 2006 Advanced AmericanTelephones. All rights reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced AmericanTelephones.
Youꢀmustꢀinstallꢀandꢀ
chargeꢀbatteryꢀbeforeꢀ
usingꢀtheꢀtelephone.
See page 8
forꢀeasyꢀinstructions.
STOP!
For customer service or product information, visit our website at
In Canada, call 1ꢀ(866)ꢀ288-4268.
Add new handsets to make your phone more versatile (see page 43)
Your telephone can accommodate up to four cordless handsets. You can add
new handsets (model E597-2, purchased separately) at any time, but each
must be registered with the base before use.
The E5943B has three handsets automatically registered as handsets 1, 2 and
3. You can register one additional handset, which will then be assigned as
number 4.
The E5944B has four pre-registered handsets.You cannot register any addi-
tional handsets.
Handset 1 Handset 2 Handset 3
Handset 4
NOTE: At any time, a maximum of two handsets or one handset and the base can be used on an
outside call, and the other two handsets can be used on an intercom call.
User’s manual
5.8 GHz Cordless
Telephone/Answering
System E5943B/
E5944B
with Caller ID/CallWaiting
Table of contents
To review the call log ................28
To return a call...........................28
Getting started
Quick reference guide .................2
Parts checklist ..............................4
Before you begin ..........................6
Telephone base installation .........7
Battery installation & charging....8
Wall mounting ..............................9
Belt clip & optional headset......10
Answering system
operation
Message capacity ........................30
Answering system ......................30
Day & time announcements ......31
Outgoing announcements..........32
Announcement only mode ........33
Change feature options .............34
Message playback .......................35
Recording & playing memos......36
Message counter displays ..........37
Remote access............................38
Telephone operation
Basic handset operation ............11
Basic base operation..................12
Options while on calls - handset
and base ......................................13
Intercom calls.............................15
Call forward ..............................16
Call transfer .............................17
Handset settings.........................18
Base settings...............................20
Appendix
Screen icons, indicator lights
& tones........................................40
Handset display screen
messages .....................................41
Adding new handsets .................43
Replacing a handset....................44
Troubleshooting .........................45
Important safety instructions ...52
FCC Part 68 and ACTA .............55
FCC Part 15................................56
Limited warranty.......................57
Technical specifications .............60
Index............................................61
Remote access wallet card........62
Directory
Directory ....................................21
New directory entries...............22
Directory search........................24
To dial, delete or change
entries .........................................25
Caller ID log
Shared caller ID log ...................26
How caller ID works .................26
About names...............................27
ꢀ
Getting started
Quick reference guide
Cordless handset
SELECTꢀMENU
CallerꢀIDꢀ(VCID)
Press to scroll down while in menus.
Press to display caller ID information
(see page 28). While entering names
or numbers, press to move the cursor
to the left.
Press to display menu, or to select
highlighted item from menu or save
an entry.
^DIR
PHONEꢀFLASH
Press to scroll up while in menus.
Press to display directory entries
(see page 24). While entering
names, press to move the cursor to
the right.
Press to make or answer a call.
During a call, press to receive an
incoming call if call waiting is activated
(see page 13).
ꢀOFFꢀCLEAR
MUTEꢀDELETE
During a call, press to hang up.
While using menus, press to cancel
an operation, return to the previous
menu, or exit the menu display.
While on a call, press to mute micro-
phone (see page 14).
While reviewing the call log, press to
delete an individual entry, or press and
hold to clear the caller ID log (see page
28).
REDIALꢀPAUSE
Press to view redial memory (see
page 11). While entering numbers,
press and hold to insert a dialing
pause (see page 22).
While pre-dialing, press to delete digits
from a string (see page 11).
ꢀSPEAKER
ꢀINTERCOM
Press to activate handset speaker-
phone. Press again to resume normal
handset use (see page 11).
Press to initiate an intercom conver-
sation, transfer or forward a call (see
pages 15-17).
Feature menu
> shows a highlighted item
Featureꢀmenu
Press VCID or ^DIR to
scroll through menu items.
>DIRECTORY
CALL LOG
DIRECTORY....... See page 21
CALL LOG.......... See page 26
RINGER VOLUME
Press SELECTꢀMENU to select
or modify a highlighted item.
.......................... See page 18
RINGER TONE... See page 18
KEY TONE.......... See page 18
LANGUAGE........ See page 19
CLR VOICE MAIL
Press OFFꢀCLEAR to cancel
an operation, return to the
previous menu, or exit the
menu display.
.......................... See page 19
DIAL TYPE......... See page 19
Menu
ꢁ
Getting started
Quick reference guide
Telephone base
Telephoneꢀfunctionꢀkeys
HANDSETꢀLOCATOR/
INTERCOM...............Press to make handset(s) beep (see page 12),
initiate an intercom conversation, transfer or
forward a call (see pages 15-17).
REDIAL/PAUSE .......Press to activate the speakerphone to
dial out the most recently called number.
When the speakerphone is already on, press
to dial out the most recently called number or
press and hold to insert a three second dialing
pause.
FLASH ......................During a call, press to receive an incoming call
if call waiting is activated (see page 13).
VOLUME ................Press to adjust speakerphone listening volume
(see page 13) or base ringer volume (see page
20).
ꢀMUTE ....................While on a call, press to mute microphone;
press again to resume (see page 14).
ꢀSPEAKER .............Press to turn speakerphone on or off (begin or
end a call, see page 11).
Answering system controls (see pages 30-39)
Press to repeat mes-
sage. Hold to slow play-
back. Press twice to hear
previous message.
Press to skip to
next message.
Hold to speed up
playback.
Press to play or stop playing messages.
ꢀANSWERꢀON/OFF
.................................Press to turn answering system on or off.
DELETE ...................Press to delete a message during playback.
Press and hold to delete all old messages when
set is idle.
TIME/SET ................Press to review or set the answering system
clock.
SETUP .....................Press to review or change answering system
options.
CHANGE ..................Press to change a setup option.
REC/MEMO .............Press to record a memo or press after pressing
SETUP to record an outgoing announcement.
ꢂ
Getting started
Parts checklist for E5943B
Save your sales receipt and original packaging in case you need to ship your
telephone for warranty service. Check to make sure the telephone package
includes the following:
Telephone base
Cordless handsets
Cordless handset chargers
Power adapter for
telephone base
Power adapters for
handset charger
Battery packs
Telephone line cord
Belt clips
Wall mount bracket
ꢃ
Getting started
Parts checklist for E5944B
Save your sales receipt and original packaging in case you need to ship your
telephone for warranty service. Check to make sure the telephone package
includes the following:
Wall mount bracket
Telephone base
Cordless handsets
Belt clips
Power adapter for
telephone base
Power adapters for cord-
less handset charger
Cordless handset chargers
Battery packs
Telephone line cord
ꢄ
Getting started
Before you begin
About caller identification
Telephone operating range
Caller ID with call waiting features
in this telephone lets you see
who’s calling before you answer
the phone, even when you’re on
another call.These features require
services provided by your local
telephone company.
This cordless telephone operates
with the maximum power allowed
by the Federal Communications
Commission (FCC). Even so, the
handset and base can communi-
cate over only a certain distance
— which can vary with the loca-
tions of the base and handset, the
weather, and the construction of
your home or office.
Contact your telephone service
provider if:
• you have both caller ID and call
waiting, but as separate services
(you may need combined ser-
vice).
If you receive a call while you
are out of range, the handset
might not ring — or if it does ring,
the call might not connect when
you press PHONEꢀFLASH. Move
closer to the base, then press
PHONEꢀFLASH to answer the call.
• you have only caller ID service,
or only call waiting service.
• you don’t subscribe to any caller
ID or call waiting services.
If you move out of range during
a telephone conversation, you
might hear noise or interference.
To improve reception, move closer
to the base.
You can use this telephone with
regular caller ID service, and you
can use its other features without
subscribing to either caller ID or
combined caller ID with call wait-
ing service.There may be fees for
these services, and they may not be
available in all areas.
If you move out of range with-
out pressing
ꢀOFFꢀCLEAR, your
telephone will be left "off the
hook".To hang up properly, walk
back towards the telephone base,
Caller ID features will work only
if both you and the caller are in
areas offering caller ID service, and
if both telephone companies use
compatible equipment.
periodically pressing
ꢀOFFꢀCLEARꢀ
until the call is disconnected.
See Caller ID log, beginning on
page 26, for more details about
how these features work.
ꢅ
Getting started
Telephone base installation
Install the telephone base as shown below. Choose a location in a central loca-
tion within the home and:
• away from any other cordless (wireless) device such as cordless telephones,
802.11 wireless router (for example,WiFi).
• away from other electronic equipment such as microwave ovens, televisions,
computers, etc. Avoid excessive heat, cold, dust or moisture.
• if you need to install your phone within the same room as other cordless
phones or wireless products, you may need to select a different channel for
your router and or other cordless phones.
Plug telephone line cord
into telephone jack.
Plug the power adapter
into an electrical outlet
not controlled by a wall
switch.
NOTE: Use only the power adapter supplied with this product. If you need a replacement, call 1 (800)
222-3111. In Canada, call 1 (866) 288-4268. Be sure to use an electrical outlet not controlled by a wall switch.
ꢆ
Getting started
Battery installation & charging
After battery installation, place each handset in the telephone base or a charger
and allow it to charge for 16 hours before use. You can keep the battery packs
charged by returning the handsets to the telephone base or chargers after each
use. When the battery is fully depleted, a recharge takes about 16 hours. The
average talk time on a fully charged battery is about eight hours depending on
environmental conditions, standby time is approximately four days.
Press in and downward on
the tab to open the battery
compartment cover.
Plug the battery
pack connector
into handset.
Place the battery
pack and wires in
the compartment.
Slide battery compart-
ment cover up until it
clicks closed.
Place handset in base or
charger to charge for 16 hours
before first use.
Plug power adapter into the jack
on the underside of charger as
shown, then plug into an electri-
cal outlet.
LOW BATTERY
Low battery indicator
Return handset to base
or charger to recharge
when this symbol flash-
es. (Handset will beep
when battery is low.)
Caution: Use only supplied rechargeable battery or replacement battery pack (part number 80-5848-
00-00).
NOTE: Use only the power adapter supplied with this product. If you need a replacement, call 1 (800)
222-3111. In Canada, call 1 (866) 288-4268. Be sure to use an electrical outlet not controlled by a wall switch.
ꢇ
Getting started
Wall mounting
The base can be installed on any standard wallphone outlet as shown below.
Choose a location away from any electronic equipment, such as personal com-
puters, computer routers, television sets or microwave ovens. Avoid excessive
heat, cold, dust or moisture.
1) Connect telephone line cord and
power adapter to telephone jacks
b
b
and wall jacks, as shown on page 7.
2) Install wall mount bracket onto set.
(a) First put the two front wall mount
bracket tabs into the front notches
on the bottom of telephone base.
(b) Squeeze the rear tabs of the wall
mount bracket as you insert them
into the rear notches on the bottom
of the telephone base.
a
a
Plug power adapter into an electrical
outlet not controlled by a wall switch.
3) Position the wall mount
bracket over the wall outlet
mounting pegs, and press
and slide the wall mount
bracket down firmly so it is
held securely on the outlet
mounting pegs.
Plug telephone line
cord into the telephone
jack.
ꢈ
Getting started
Belt clip & optional headset
Install belt clip as shown below if desired.
Snap belt clip into notches on
side of handset. Rotate and
pull to remove.
For hands-free telephone conversations, you can use any industry standard
2.5 mm headset (purchased separately). For best results, use an AT&T 2.5 mm
headset.
Plug 2.5 mm headset
into the jack on the side
of handset (beneath
small rubber cap).
ꢀ0
Telephone operation
Elapsed time
Basic handset operation
PHONE
00:00:12
Making and answering calls
To answer an incoming call, press PHONEꢀFLASH or
ꢀSPEAKER, or any dial pad key (0-9, * or #). To
make a call, press PHONEꢀFLASH or
ꢀSPEAKER,
then dial a number. Press ꢀOFFꢀCLEAR to hang up.
To preview numbers before dialing, enter numbers
first, then press PHONEꢀFLASH or ꢀSPEAKER to
dial. Press MUTEꢀDELETE or
ꢀOFFꢀCLEAR at any time
to make corrections as you are entering numbers.
The screen displays the elapsed time as you talk (in
hours, minutes and seconds).
SPEAKER
00:00:12
Hands-free speakerphone calls
To answer a call, press ꢀSPEAKER. To make a call,
press ꢀSPEAKER, then dial a number. During a
call, you can press ꢀSPEAKER to toggle between
hands-free speakerphone and normal handset use.
Press ꢀOFFꢀCLEAR to hang up.
Last number redial
REDIAL
Press REDIALꢀPAUSE to display the most recently
called numbers (up to 32 digits). Use the V^ but-
tons or REDIALꢀPAUSE repeatedly to view up to five
recently called numbers. The handset will beep at
the beginning or end of the list.
555-1234
To dial any redial number displayed, press PHONEꢀ
FLASH or
ꢀSPEAKER. Or, after pressing PHONEꢀ
FLASH or
ꢀSPEAKER, press REDIALꢀPAUSE to call the
most recently called number (up to 32 digits).
Press MUTE DELETEꢀto delete the number from the
redial memory.
ꢀꢀ
Telephone operation
Basic base operation
Making and answering calls
To answer an incoming call, press ꢀSPEAKER, or
any dial pad key (0-9, * or #). To make a call, press
ꢀSPEAKER, then dial a number. Press
ꢀSPEAKER
again to hang up.
Speakerphone
Last number redial
When the base is idle, press REDIALꢀ/PAUSE will
activate the speakerphone and dial out the most
recently called number (up to 32 digits).
-OR-
When the speakerphone is already on during an
external call, pressing REDIALꢀ/PAUSE to immediately
dial out the most recently called number (up to 32
digits).
NOTES:
1. After pressing speaker on the base, if you press and hold REDIALꢀ
/PAUSE
while dialing, it will insert a 3-second dialing pause.
2. If you dial a number after pressing FLASH, that dialed number will
not be saved for redial, so when you press ꢀSPEAKER and then
REDIALꢀ/PAUSE, you can only dial out the second latest called number.
Handset locator
If you misplace the handset(s), press HANDSETꢀ
LOCATORꢀ/INTERCOM at the base. This starts the pag-
ing tone at the handset(s) for 60 seconds to help
you locate it. To stop the paging tone, press PHONEꢀ
FLASH,ꢀ ꢀSPEAKER, or any dial pad key (0-9, *, or #)
on the misplaced handset(s) (the handset(s) not on
the cradle), or press HANDSETꢀLOCATOR/INTERCOM at
the base.
Tone
NOTES:
1. The handset ringer volume also determines the level of the paging
tone. If the handset ringer volume level is set to off (0), that handset
will be silenced for all calls and paging (see page 18).
2. During a page, if you press OFFꢀCLEAR on the misplaced handset(s)
(the handset(s) not on the cradle), the ringer of that handset will be
silenced, but the page will not be cancelled.
ꢀꢁ
Telephone operation
Options while on calls -
handset and base
Volume control
Press ^ꢀor V on the VOLUME button on the side
of the handset or press ^ or V on the VOLUME
button on the base to adjust the listening volume
levels (1-5, of which 5 is the highest).
Volume
When you change the volume level, the new set-
ting will automatically be saved.
Flash
Call waiting
If you subscribe to a call waiting service with your
local telephone service provider, you will hear
a beep if someone calls while you are already on
a call. Press PHONEꢀFLASH to put your current
call on hold and take the new call. You can press
PHONEꢀFLASH at any time to switch back and forth
between calls.
Flash
Volume
Three-way conference calls
While a call is in progress, a person at another
handset can press PHONEꢀFLASHꢀor
ꢀSPEAKER
to join the call. A person at the base can press
ꢀSPEAKER to join the call.
A person at either handset can press
ꢀOFFꢀCLEAR,
or place the handset in the base to drop out of the
conference call. A person at the base can press
ꢀSPEAKER to drop out of the conference call. A
conference call will not be terminated until all the
handsets and the base hang up.
Only two handsets (or one handset and the base)
can connect to an outside call at any one time.
ꢀꢂ
Telephone operation
Options while on calls -
handset and base
Mute
Press MUTEꢀDELETE to silence the microphone. You
will be able to hear the person at the other end,
but they will not be able to hear you until you
press MUTEꢀDELETE again and resume speaking.
Temporary ringer silencing
Tone
Mute
Press OFFꢀCLEAR or MUTEꢀDELETE while the phone
is ringing to silence the ringer temporarily.
The next phone call will ring normally.
Temporary tone dialing
If you have pulse dialing (rotary) service, you can
switch to touch tone dialing during a call by press-
ing *. This can be useful if you need to send tone
signals to access answering systems or long dis-
tance services.
Mute
After you hang up or press FLASH to access ser-
vices with your local telephone service provider,
the phone automatically returns to pulse dialing
(rotary) service.
ꢀꢃ
Telephone operation
Intercom calls
Intercom calls
If you have more than one handset, use the inter-
com feature to have conversations between the
handsets and base.
• Press the ꢀINTERCOM button on a handset or
HANDSETꢀLOCATOR/ꢀINTERCOM on the base to initi-
ate an intercom call.
• After entering the number of the handset (1-4
or 0 for the base) you wish to intercom with,
your handset (or base) will call the other hand-
set (or base).
Press INTERCOM.
To answer the intercom call:
• At a handset, press ꢀINTERCOM,ꢀ PHONEꢀ
FLASH,ꢀ ꢀSPEAKER or any dial pad key (0-9, * or
#).
• At the base, press HANDSETꢀLOCATOR/ꢀINTERCOM,ꢀꢀ
ꢀSPEAKER or any dial pad key (0-9, * or #).
Select a station to page.
INTERCOM TO:
To end the intercom call:
• At a handset, press
ꢀOFFꢀCLEAR or
ꢀINTERCOM,
or place the handset in a charger or base.
• At the base, press HANDSETꢀLOCATOR/ꢀINTERCOM or
ꢀSPEAKER.
Handling incoming calls
The phone will beep if you receive an outside call
during an intercom conversation.You can either:
NOTE: The intercom fea-
ture cannot be used while a hand-
set is in the directory or call log.
Pressing ꢀINTERCOM while on
an outside call will initiate call
transfer (see page 17). Pressing
and holding ꢀINTERCOM while
on an outside call will initiate call
forward (see page 16).
• Press PHONEꢀFLASH or ꢀSPEAKERꢀto end the
intercom call and answer the incoming call.
-OR-
• Press ꢀINTERCOM or
ꢀOFFꢀCLEAR on the hand-
set or HANDSETꢀLOCATOR/ꢀINTERCOM on the base
to disconnect the intercom connection without
answering the incoming call. The incoming call
will continue to ring.
ꢀꢄ
Telephone operation
Call forward
An external call can be forwarded between the fol-
lowing parties:
• From one handset to another handset (pur-
chased separately).
• From a handset to the base.
• From the base to a handset.
Call forward
During a conversation, you can forward the call to
another handset or to the base.
• Press ꢀINTERCOM on the handset or HANDSETꢀ
LOCATOR/ꢀINTERCOM on the base.
FORWARD TO:
• Enter the handset number (1-4 or 0 for the
base) to which you want to forward the call.
• The destination set will ring.
• Press PHONEꢀFLASH, ꢀSPEAKER or any dial pad
key (0-9, * or #) on the destination handset to
answer the call. On the base, press ꢀSPEAKER
or any dial pad key (0-9, * or #) to answer
the call. Press ꢀOFFꢀCLEAR on the handset or
ꢀSPEAKER on the base that originated the for-
ward to drop out.
NOTE: If the forwarded call is not answered within 30 seconds,
the external call will be returned to the base or handset that originated
the forward, and its display will show CALL BACK. If the returned call is
not answered within an additional 30 seconds, the external call will end
automatically.
ꢀꢅ
Telephone operation
Call transfer
An external call can be transferred between the
following parties:
• From one handset to another handset (pur-
chased separately).
• From a handset to the base.
• From the base to a handset.
Call transfer
During a conversation, you can transfer the call to
another handset or to the base.
• Press ꢀINTERCOM on the handset or HANDSETꢀ
LOCATOR/ꢀINTERCOM on the base (the external
call is put on hold).
TRANSFER TO:
• Enter the handset number (1-4 or 0 for the
base) to which you want to transfer the call.
• The destination set will ring, showing an inter-
com call.
• Press ꢀINTERCOM, PHONEꢀFLASH, ꢀSPEAKER
or any dial pad key (0-9, * or #) on the des-
tination handset to answer the intercom call.
On the base, press HANDSETꢀLOCATOR/ꢀINTERCOM,
ꢀSPEAKER or any dial pad key (0-9, * or #) to
answer the intercom call.
• When the recipient answers the intercom call,
you can talk privately without the outside caller
hearing the conversation.
• On a handset, press ꢀOFFꢀCLEARꢀto transfer the
call. On the base, press ꢀSPEAKER to complete
the transfer to a handset.
NOTES:
1. If the intercom call is not answered within approximately 100 sec-
onds, the external call will be released from hold at the originating
set.
2. When the recipient answers the intercom call, the originating party
can toggle between the intercom and external calls by pressing
ꢀINTERCOM on the handset or HANDSETꢀLOCATOR/ꢀINTERCOM on the
base.
ꢀꢆ
Telephone operation
Highlighted
menu item
Handset settings
>DIRECTORY
CALL LOG
Using the feature menu, you can change settings to
customize how the telephone works.
Press SELECTꢀMENU, then use the V^ buttons
to scroll to the feature you want to change. As
you scroll through the menu, the top menu item is
always highlighted with a > symbol. Press SELECTꢀ
MENUꢀto select the highlighted item.
Press OFFꢀCLEAR at any time to cancel an opera-
tion, turn to the previous menu, or exit the menu
display.
RINGER VOLUME
Ringer volume
Using this menu you can set a ring volume level (1-
6), or turn the ringer off (0). Use the V^ buttons
to hear a sample of each volume level, then press
SELECTꢀMENUꢀto select the one you prefer.
-OR-
When the handset is in idle mode, press VOLUME
^V buttons on the right side of the handset to
change ringer volume directly.
Ringer tone
This feature allows you to choose one of 10 ring-
ing tones. Use the V^ buttons to hear a sample
of each ringer tone, then press SELECTꢀMENUꢀto
select the one you prefer.
RINGER TONE
1
Key tone
The handset is factory programmed to beep at
each key press. Use the V^ buttons to select ON
or OFF, then press SELECTꢀMENUꢀto save your pref-
erence.
KEY TONE
ON
NOTES:
1. The ringer volume level also determines the levels of ringing for
intercom calls (see page 15) and the paging tone when initiating the
handset locator feature (see page 12). If the handset ringer volume
level is set to off (0), that handset is silenced for all calls and paging.
2. If you select OFF, you will not hear the beep tone when you press
keys.
ꢀꢇ
Telephone operation
Handset settings
Language
LANGUAGE
ENGLISH
At this menu, you can select the language used in
all menus and screen displays. Use the V^ but-
tons to select ENGLISH, SPANISH or FRENCH,
then press SELECTꢀMENUꢀto save your preference.
The default language is English, only change this
option if you wish to see the menu and screen dis-
played in Spanish or French.
>DIRECTORY
CALL LOG
Clear voice mail indication
>CLR VOICE MAIL
DIAL TYPE
If you subscribe to voice mail services provided
by your local telephone company, you will receive
a text message NEW VOICE MAIL on the hand-
set when you have new voice mail. To manually
remove the voice mail message on the display:
TURN IDICATOR
OFF?
• Press SELECTꢀMENU.
• Press the V or ^ button to highlight CLR
>CLR VOICE MAIL
DIAL TYPE
VOICE MAIL.
• Press SELECTꢀMENU.
• Press SELECTꢀMENU again to remove the dis-
played message, or press OFFꢀCLEAR to exit.
NOTE: This only turns off the displayed message, it does not
delete your voice mail message(s). Use this feature when the phone
indicates there is voice mail when you have none. If there actually is a
new voice mail message, your local telephone company will continue to
send the message which turns the display message back on.
DIAL TYPE
TONE
Dial type
Using this menu, you can choose TONE or PULSE
dialing. The factory default setting is TONE.
Change this to PULSE only if you do not have
touch tone dialing service.
Use the V^ buttons to select TONE or PULSE,
then press SELECTꢀMENUꢀto save your preference.
ꢀꢈ
Telephone operation
Base settings
Ringer volume
You can set a base ring volume level (1-6), or turn
the ringer off (0).When the base is idle, use the ^
or V on the VOLUME button to hear an example
of each volume level and save the one you prefer.
NOTE: The ringer volume level also determines the level of ring-
ing for intercom calls (see page 15). If the base ringer volume level is
set to off (0), the base will be silenced for all calls.
ꢁ0
Directory
Shared directory
Pat Williams
555-1234
The directory is stored in the base, and is shared
by all handsets. Changes made at any one handset
will be reflected in all.
Memory capacity
The directory can store up to 50 entries. Each
entry can contain a number up to 32 digits, and a
name up to 16 letters long. A convenient search
feature can help you find and dial numbers quickly
(see page 24).
Timeouts and error messages
If you pause for too long while making an entry,
the procedure will time out and you will have to
begin again.
If all memory locations are in use, the screen will
display LIST FULL. You will not be able to store a
new number until you delete an existing one.
ꢁꢀ
Directory
HANDSET 1
New directory entries
To create a new directory entry
Press SELECTꢀMENU, then press SELECTꢀMENU to
choose DIRECTORY. Press V to highlight STORE.
Press SELECTꢀMENU, then enter the telephone
number when prompted.
>DIRECTORY
CALL LOG
Use the dial pad to enter up to 32 digits, or copy
a number from redial by pressing REDIALꢀPAUSE
and using V^ to locate the number to copy, and
then pressing SELECTꢀMENU to copy the number.
Press SELECTꢀMENU to save the number in the dis-
play. The display will show ALREADY SAVED if the
number is already in your directory.
>STORE
REVIEW
• Press MUTEꢀDELETEꢀto erase numbers if you make
a mistake.
• Press and hold REDIALꢀPAUSE to enter a 3-second
dialing pause.
ENTER NUMBER
555-1234_
To enter a name
Use the dial pad and the table below to enter a
name (up to 16 characters). Each press of a par-
ticular key will cause characters to be displayed in
the following order:
ENTER NAME
Pat Williams_
Characters by number of key presses
Dial
key
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
0
ꢀ
ꢂ
ꢄ
ꢆ
ꢍ
ꢑ
ꢒ
!
D
"
E
#
F
ꢇ
3
A
d
G
J
B
e
C
f
I
'
*
(
+
.
1
5
8
)
ꢈ
ꢉ
ꢊ
3
ꢋ
:
H
K
,
/
2
6
9
L
Pat Williams
555-1234
-
0
4
M
ꢎ
T
N
P
U
W
O
Q
V
X
R
S
Z
7
ꢁ
ꢏ
Y
ꢃ
ꢅ
ꢌ
ꢐ
#
SPACE
ꢁꢁ
Directory
New directory entries
The cursor moves to the right when you press
another dial pad button or the ^ button. Press V
to move the cursor to the left. Press MUTEꢀDELETE
to erase letters if you make a mistake.
Storing the entry
Press SELECTꢀMENUꢀto store your new directory
entry. To change it later, see page 25.
ꢁꢂ
Directory
HANDSET 1
Directory search
To browse through the directory
Press ^DIR to display the first listing in the direc-
tory. You can then use the V or ^ to browse
through the directory, or search to find a specific
entry. Entries will be displayed alphabetically by the
first letter in the name. Press OFFꢀCLEAR at any
time to exit the directory.
Andrew
555-6789
NOTE: You can also display the first listing in the directory by
first pressing SELECTꢀMENU, then SELECTꢀMENU to choose
DIRECTORY, and then SELECTꢀMENU again to choose REVIEW.
Barbara
555-9876
To search by name
Or
When any entry is displayed, you can press a dial
pad key to display the first name beginning with a
letter associated with that key.
5ꢀ
Press the appropriate dial pad keys once for the
first letter, twice for the second, three times for
the third, as shown on page 22.
Jennifer
555-4321
For example, press 5ꢀ(JKL) once to find Jennifer,
twice to find Kevin, or three times to find Linda.
7ꢀ
Pat
555-1234
Viewing long numbers
The screen can display only 16 digits at a time.To
view numbers longer than this, press * or # to
display the remaining digits.
ꢁꢃ
Directory
HANDSET 1
To dial, delete or change entries
To dial a displayed number
When any directory entry is displayed, press
PHONEꢀFLASH (or ꢀSPEAKER) to dial the displayed
number.
Andrew
555-6789
To delete an entry
When any directory entry is displayed, press MUTEꢀ
DELETE to delete the displayed entry from the
directory. Once deleted, an entry cannot be recov-
ered.
EDIT NUMBER
555-6789_
To change an entry
When any directory entry is displayed, press
SELECTꢀMENU to modify the entry:
• You are prompted to EDIT NUMBER. Press
MUTEꢀDELETE to erase digits.Then you can enter
the correct telephone number. You can use the
V button to move the cursor to the left and
the ^ button to move the cursor to the right.
Press and hold REDIALꢀPAUSE to add a 3-second
pause if necessary.
EDIT NAME
Andy_
You can also press REDIALꢀPAUSE, then V^ to
scroll to the previously dialed number from the
redial list you want to store in the directory,
then press SELECTꢀMENU.
Andy
555-6789
• Press SELECTꢀMENU.
• You are now prompted to EDIT NAME. Press
MUTEꢀDELETE to erase characters, then use the
dialing keys to enter the correct name (see page
22).You can also use the V button to move the
cursor to the left and the ^ button to move
the cursor to the right.
• Press SELECTꢀMENU.
ꢁꢄ
Caller ID log
Shared caller ID log
The caller ID log is stored in the base, and is
shared by all handsets. Changes made at any one
handset will be reflected in all.
CHARLIE JOHNSON
1-888-883-2445
11/23 10:01AM
How caller ID works
If you subscribe to caller ID service provided by
your local telephone company, information about
each caller will be displayed between the first and
second ring.
Caller’s name
Caller’s number
CHARLIE JOHNSON
1-888-883-2445
NEW
Appears when
the call is
11/23 10:01AM
missed and un-
reviewed.
Time of call
Date of call
Information about the last 50 incoming calls is
stored in the call log. You can review the call log
to find out who has called, easily return the call, or
copy the caller’s name and number into your direc-
tory.
When the call log is full, the earliest entry is delet-
ed to make room for new incoming call informa-
tion.
If you answer a call before the information appears
on the screen, it will not be saved in the call log.
NOTES:
1. Caller ID features will work only if both you and the caller are in
areas offering caller ID service, and if both telephone companies use
compatible equipment.
2. When in idle mode, the cordless handset screen will show XX
MISSED CALLS. The call log review displays the caller ID in reverse
chronological order, with the latest one first. Each time a call log
entry marked NEW is displayed, the number of new calls decreases
by one. Any entries which have not been reviewed will be counted as
MISSED CALLS when the phone is idle.
ꢁꢅ
Caller ID log
Caller ID log
About names
Names of callers will be displayed only if the infor-
mation is provided by your local telephone com-
pany.
If the telephone number of the person calling
exactly matches a number in your directory, the
name that appears on screen will match the name
as you entered it into your directory.
(Example: If Christine Smith calls, her name will
appear as Chris if this is how you entered it into
your directory.)
ꢁꢆ
Caller ID log
HANDSET 1
6 MISSED CALLS
To review the call log
To review the call log
Press VCID to review the call log. The most recent
call is displayed first. Use the arrow buttons to
scroll through the list as shown on the left.
Pat Williams
555-1234
NEW 11/23 10:31AM
To return a call
Press PHONEꢀFLASH (or ꢀSPEAKER) to call the
number as displayed.
Caller ID numbers may appear with an area code
that may not be required for local calls, or without
a ꢀ that may be needed for long distance calls. If
the number displayed is not in the correct format,
you can change how it is dialed.
Chris Thompson
908-555-0100
11/23 10:21AM
NEW
To change the number before calling, press #
repeatedly to see different dialing options (you can
choose to dial with or without area code, and with
or without the ꢀ), then press PHONEꢀFLASH (or
ꢀSPEAKER) to place the call.
Jeffrey Adams
555-9876
11/23 10:11AM
NEW
Example:
VCID.......................Number displayed as 908-555-0100
#(three times).......Number changes to 555-0100 (drops 1 + area
code)
PHONEꢀFLASH/
ꢀSPEAKER..........Dials 555-0100
NOTE: If both the name
and number are not provided,
UNABLE TO SAVE will be dis-
played.
Other options
• Press MUTEꢀDELETE to delete this entry from the
call log.
• Press and hold MUTEꢀDELETE to delete all entries
from the call log. When asked to confirm, press
SELECTꢀMENUꢀto clear the call log of all entries,
or press ꢀOFFꢀCLEAR to exit and leave all call
log entries intact.
ꢁꢇ
Caller ID log
To review the call log
• Press SELECTꢀMENUꢀto copy this entry into your
directory. If the name or number is not pro-
vided, you will be prompted to enter them (see
page 22).
• Press and hold OFFꢀCLEAR for four seconds,
the number of missed calls shown on the mes-
sage counter will be reset to 0.
ꢁꢈ
Answering sys-
tem operation
Message capacity
The answering system can record up to 99 mes-
sages, depending on the length of each message.
Individual messages can be up to four minutes long,
and total maximum recording time is 18 minutes.
Messages will remain available for replay until you
delete them.
Message counter
Number of messages (or,
during playback, message
number currently playing).
Press repeatedly to hear
Press to select or change a Press to record a memo (see page
setup options (see page 34). setup option (see page 34). 35) or, after pressing SETUP, to
record an outgoing announcement
(see page 32).
Press to review or set
clock (see page 31).
Press to exit setup or clock
options. Press to stop
recording a memo or outgo-
ing announcement. Press to
start or stop message play-
back (see page 35).
Press to delete message
currently playing; hold to
delete all old messages
(see page 35).
Press to repeat message;
hold to slow playback,
press twice to play previ-
ous message (see page
35).
Press to skip message;
hold to speed up playback
(see page 35).
Press to turn answer-
ing system on or off.
ꢂ0
Answering system operation
Turning the answering sys-
tem on and off
Day and time announcements
To set day & time
Before playing each message, the answering sys-
tem announces the day and time the message was
received.
Press TIMEꢀ/SET
1.ꢀ
Before using the answering system, you should fol-
low the steps on the left to set the day and time,
so messages are dated correctly.
The system will announce the
current clock setting, then
announce “To begin setting the
clock, press TIME/SET, then press
CHANGE to change the setting or
press TIME/SET to continue.”
The system uses voice prompts to guide you. Each
time you press CHANGE, the day, hour, minute or
year advances by one. When you hear the correct
setting, press TIME/ꢀSET to move to the next setting.
Press TIMEꢀ/SET
2.
Press CHANGE
3.
To check day & time
until the system announces
the correct day, then press
TIME/ꢀSET.
You can press TIMEꢀ/SET at any time to hear the
current day and time without changing it.
Press CHANGE
4.
until the system announces
the correct hour, then press
TIME/ꢀSET.
NOTES:
1. Press and hold CHANGE to advance the minute or year by increments of
10 (the year can be set from 2000 to 2039).
2. Caller ID provides the time and date. Set the year so that the day of the
week can be calculated from the caller ID information. After you set the
time once, it will thereafter be set automatically with incoming caller ID
information. The time will be set automatically only if you subscribe to
caller ID service provided by your local telephone company (see page 6).
Press CHANGE
5.
until the system announces
the correct minutes, then
press TIME/ꢀSET.
Press CHANGEꢀ
6.
until the system announces
the correct year, then press
TIME/ꢀSET. The system
announces the current
clock setting.
ꢂꢀ
Answering system operation
Outgoing announcements
Outgoing announcements are the messages call-
ers hear when calls are answered by the answering
system.
The phone is pre-programmed with announce-
ments for normal (answer and record) mode and
for announcement only mode (see page 33). If the
phone is set up to record messages, the phone
answers calls with “Hello. Please leave a message
after the tone.” You can use this announcement, or
replace it with a recording of your own voice.
Elapsed
recording time
(in seconds).
Press to stop
recording.
SETUP
1.
2.
“Announcement. Press
PLAY or ...”
(Play /Stop)
To record your outgoing announcement
(Plays announce-
ment previously
recorded).
Press SETUP until you hear "Announcement. Press
PLAY or press RECORD. To continue setup, press
SETUP." Then press RECꢀ/MEMO and begin speaking
after you hear "Record after the tone. Press STOP
when you are done." Speak facing the telephone
base from about nine inches away. Press PLAY/ꢀSTOP
when you are done.
-OR-
RECꢀ/MEMO
2.
“Record after the tone. . .”
Elapsed time (in seconds) will be shown in
the message window as you record. You can
record an announcement up to 90 seconds long.
Announcements less than three seconds long will
not be recorded.
3. Speak into microphone.
To delete your outgoing announcement
Press SETUP until you hear “Announcement. Press
PLAY or press RECORD. To continue setup, press
SETUP.” Then press PLAYꢀ/STOP to begin play-
back. PressꢀDELETE during playback to delete your
announcement.
Microphone
4.
(Play /Stop)
(Announcement is
played back).
When your announcement is deleted, calls will be
answered with the pre-programmed announcement
described above.
ꢂꢁ
Answering system operation
Announcement only mode
In announcement only mode, callers hear an
announcement but cannot leave messages.
A
A is displayed when announce-
ment only is activated.
To turn Announcement only on or off
Press SETUP repeatedly until you hear
“Announcement only, record no messages.To change
the setting press CHANGE.” Then press CHANGE
until you hear the option you want (on or off).
Press PLAY/ꢀSTOP to store your selection and exit,
or press SETUP again to modify other features
(see page 34).
SETUP
1.
“Announcement
only, record no mes-
sages. To change
the setting press
CHANGE.”
CHANGEꢀ
2.
“Off”
To record your outgoing announcement
When announcement only is turned on, calls are
answered with a pre-recorded announcement that
says “We’re sorry, messages to this number cannot
be accepted.” You can use this announcement, or
replace it with a recording of your own voice.
CHANGEꢀ
3.
“On”
4.
(Play/ Stop)
After turning on the announcement only fea-
ture, follow the steps on page 32 to record your
announcement. Callers will hear this announce-
ment only when the announcement only feature is
turned on. Otherwise they will hear the standard
announcement asking them to leave a message.
Beep
(Option selected).
ꢂꢂ
Answering system operation
Change feature options
You can change how the answering system oper-
ates. Press SETUP repeatedly to hear each feature.
Press CHANGE when you hear the feature you want
to modify.
SETUP
1.
2.
Press until desired feature
is heard (see list at right).
Feature.options.(default.settings.underlined)
System announces:
Feature description:
CHANGEꢀ
“Announcement. Press
PLAY or press RECORD.
To continue setup, press
SETUP.”
Options: [record announce-
ment]
Press RECꢀ/MEMO to record your
outgoing announcement (see page
32). Press PLAY/ꢀSTOP to stop
recording.
Press until desired selec-
tion is heard.
SETUPꢀ
3.
“Remote access code. To
change the setting press
CHANGE.”
Options: [enter two-digit
code] 19
Enter a two-digit number (10-99) for
remote access from another phone
(see page 38).
Press to set selection and
move to next menu option.
-OR-
“Message alert. To change
the setting press CHANGE.”
Options: On / Off
When the answering system is turned
on (the ANSWERꢀON/OFF light is lit)
and the message alert function is acti-
vated, any new incoming message will
increase the flashing number in the
message window by one, and a beep
tone will sound every ten seconds as
a reminder that there are unreviewed
messages on the answering system.
(Play/ Stop)
Press to set selection and
exit setup.
NOTES:
1. To temporarily disable the
message alert tone, press any
answering machine key (TIME/
SET,ꢀSETUP,ꢀCHANGE,ꢀREC/
MEMO,ꢀPLAY/STOP,ꢀDELETE,ꢀ
“Announcement only,
record no messages. To
change the setting press
CHANGE.”
When on, callers hear an announce-
ment but cannot leave messages (see
page 33).
REPEAT and SKIP) on the base.
This turns off the audio message
alert tone but the number in the
message window will continue
to flash as a reminder that there
are unreviewed messages on the
answering system. The message
alert tone will be re-activated
with the next incoming message.
Options: On / Off
“Call screening. To change
the setting press CHANGE.”
Options: On / Off
When on, you can hear callers leave
messages, or answer the call.
“Number of rings. To
change the setting press
CHANGE.”
Choose number of rings before the
system answers a call. When toll saver
is active, the system answers after
two rings if you have new messages,
and after four rings if you have no new
messages.
2. To switch off the message
alert tone for all incoming mes-
sages, read the section on disa-
bling the message alert function
in the list on the right.
Options: 2 / 4 / 6 /Toll Saver
3. Press and hold CHANGE to
advance the remote access code
number by 10.
ꢂꢃ
Answering system operation
Number of messages (or, dur-
ing playback, message number
currently playing).
Message playback
Press PLAYꢀ/STOP to hear messages.The system
announces the number of messages, then begins
playback.
If you have new messages, you will hear only the
new messages (earliest first). If there are no new
messages, the system will play back all messages
(earliest first).
Press PLAY/STOP to begin
or end message playback.
Announcements
1.
(Play/Stop)
• When playback begins, you will hear the total
number of messages.
“You have [xx] new
messages and [xx]
old messages.”
Message playback begins. See
options at right.
• Before each message, you will hear the day and
time it was received.
• After the last message, you will hear "End of
messages." If the system has less than five min-
utes of recording time left, it will announce the
remaining time.
2.
(Play/Stop)
Message playback ends.
Options during playback
• Press the ꢀVOLUMEꢀbutton to adjust speaker
volume.
NOTES:
1. If F is flashing in the mes-
sage window, memory is full.
You will have to delete some
messages before new ones
can be recorded.
• Press ꢀSKIP to skip to next message (or hold
down to speed up message playback).
• Press ꢀREPEAT to repeat message currently
playing. Press twice to hear previous message
(or hold down to slow message playback).
2. New (unheard) messages
cannot be deleted.
• Press DELETEꢀto delete message being played
back.
• Press PLAY/ꢀSTOPꢀto stop playback.
To delete all messages
To delete all messages, press and hold DELETE
while the phone is idle (not during a call, or during
message playback).
ꢂꢄ
Answering system operation
Recording & playing memos
Memos are messages you record yourself. They are
saved, played back and deleted exactly like incoming
messages. You can record a memo as a reminder
to yourself, or leave a message for someone else if
others in your household use the answering system.
Elapsed
recording time
in seconds.
Press to stop
recording.
To record a memo
RECꢀ/MEMOꢀ
1.
2.
Press RECꢀ/MEMO. Elapsed time (in seconds) is shown
in the message window as you record. You can
record a memo up to four minutes long. Memos
less than one second long will not be recorded.
“Record after the
tone. Press STOP
when you are done.”
Speak into microphone.
Press PLAY/ꢀSTOP to stop recording.
To play back a memo
Press PLAYꢀ/STOP to hear messages and memos (see
page 35 for other options).
Microphone
(Play/Stop)
3.
"Recorded" then beep
(Memo has been record-
ed).
ꢂꢅ
Answering system operation
Message counter displays
The message counter usually displays the total
number of memos and incoming messages. See the
list below for explanations of other displays in this
counter.
Message counter
Message counter displays
0
No messages.
1-99
Number of messages/memos, or message
number currently playing (flashes if you have
new messages).
10-99
Current remote access code while setting (see
page 34).
1-8
Current volume level while adjusting.
1-99 (counting)
Elapsed time while recording a memo (see
page 36) or announcement up to 90 seconds
(page 32).
99 (flashing)
Memo recording exceeded 99 seconds.
F (flashing)
Memory is full. Messages must be deleted
before new messages can be received.
CL (flashing)
Clock needs to be set (see page 31).
A
Announcement only mode is on (see page 33).
--
System is answering a call, or being accessed
remotely.
-- (flashing)
System is being programmed or initialized.
On (or) OF
Displayed for one second when any feature
option setting is turned on or off.
02, 04, 06, tS
Current number of rings while setting (see
page 34).
ꢂꢆ
Answering system operation
Dial your telephone number
from any touch tone phone.
1.
2.
Remote access
When system answers, enter
two-digit remote access code
(19 unless you have changed
it).
A two-digit security code is required to access
your answering system from any touch tone phone.
This code is 19 by default; see page 34 to change it.
Enter remote commands
(see list at right).
3.
4.
Press to hear all messages.
Press to hear new messages.
Play all messages
1
Hang up to end call and save
all undeleted messages.
Play new messages
2
Delete the message
3
33
Press during playback to delete cur-
rent message. Press 3 twice to delete
all old messages.
Press during the caller’s message
to repeat the message. Press during
the beginning of the day and time
announcement to go back to the pre-
vious caller’s message.
Repeat or go back
4
Press to stop any operation (stop
playback, stop recording).
Stop
5
NOTE: If you pause for
Press to skip current message and
advance to next message.
Skip to next message
6
more than 10 seconds during
remote access, you will hear a
help menu listing all features &
commands. If you issue no
command for another 20 sec-
onds, the call will end automati-
cally.
Press to review current outgoing
announcement.
Review announcement
#7
Press * 7, wait for beep, then begin
speaking. Press 5 to stop record-
ing and hear playback of the new
announcement.
Record announcement
*7to begin recording
5to stop recording
Press 8, wait for beep, then begin
speaking. Press 5 to stop recording.
Record memo
8to begin recording
5to stop recording
Press # 9 to review remote access
code.
Review remote access
code
#9
Press * 9 to change remote access
code, then enter desired remote
access code from 10-99.
Change remote access
code
*9
ꢂꢇ
Answering system operation
Remote access
Press to hear list of features & com-
mands.
Help menu
*5
Press to turn off answering system.
Incoming calls will no longer be
answered.
Turn system off
0
If off, system will answer after 10
rings. Enter your access code, then
press 0 to turn it on.
Turn system on
0
ꢂꢈ
Appendix
Screen icons, indicator lights & tones
Screen icons & alert tones
Screen icons
Ringer off.
Battery charging (animated display).
HANDSET 1
Low battery (flashing); place handset in base or charger to
recharge.
MUTE 11/23 10:01AM
NEW
Microphone is muted.
Missed and un-reviewed calls.
MUTE
NEW
Handset alert tones
Two short beeps
Press VOLUME keys while the volume levels are
already at limits.
Four short beeps
Two beeps
Low battery warning.
Out of range during off-hook.
Confirmation tone
Programming command completed successfully.
Base tones
One beep every
10 seconds
Message alert.
A series of beeps
Press VOLUME keys while the volume levels are
already at limits.
Indicator lights
ANSWER ON/OFF
On when answering system is on and
ready to receive calls.
IN USE
On when handset is in use or you
are registering a handset. Flashes
when another phone is in use on the
same line, or the answering system is
answering an incoming call, or you are
de-registering a handset from the base.
CHARGE
MUTE
On when handset
is in the cradle of
the telephone base
and charging.
On when the
telephone base
mutes a call.
SPEAKER
On when speakerphone is in use.
ꢃ0
Appendix
Handset display screen messages
Screen display messages
The handset is in use.
PHONE
ENDED
You have just ended a call.
CALL LOG EMPTY
DIRECTORY EMPTY
LIST FULL
You are accessing an empty call log.
You are accessing an empty directory.
You are saving to a full directory.
MUTED
The call is on mute.
SPEAKER
The handset speakerphone is in use.
LOW BATTERY
INCOMING CALL
NEW VOICE MAIL
The battery needs to be recharged.
There is a call coming in.
There are new voice mail messages.
There are new calls in the caller ID log.
XX MISSED CALLS
CONNECTING ...
The handset has lost communication with
the base.
** PAGING **
The base is paging handset(s).
Another handset is calling.
HANDSET X
IS CALLING
The base is calling.
BASE
IS CALLING
LINE IN USE
NO LINE
An extension phone is in use.
There is no telephone line connected.
ALREADY SAVED
SAVED
The telephone number you have entered
is already stored in the directory.
The call log entry is saved to the direc-
tory successfully.
•
The battery is not installed or not installed
properly in the handset.
WARNING
CHECK BATTERY!
-OR-
•
•
The battery needs to be replaced.
-OR-
An incorrect battery has been installed
by mistake. Use only supplied battery
or AT&T replacement battery pack (part
number 80-5848-00-00).
PLACE
IN CHARGER
The battery is very low. The handset
should be placed in the telephone base
or charger.
ꢃꢀ
Appendix
Handset display screen messages
Screen display messages
A handset with a low battery has been
CHARGING
placed in the base unit or charger.
UNABLE TO CALL
TRY AGAIN
Failed intercom or conference call (There
are already two handsets or one handset
and the base being used).
ꢃꢁ
Appendix
Adding new handsets
Your telephone can accommodate up to four cordless handsets.You can add
a new handset (E597-2, purchased separately) to the E5943B at any time, but
each handset must be registered with the base before use.
The E5943B has three handsets automatically registered as handset 1, 2 and 3.
You can register one additional handset, which will be assigned as number 4.
The E5944B has four pre-registered handsets.You cannot register any additional
handsets.
Before using a new E597-2 handset, you must regis-
NOT REGISTERED
ter it with the base.
To add a new handset:
• When first purchased, all optional accessory
PRESS HNDST LOC
4 SEC ON BASE
handsets show NOT REGISTERED on the
screen.
• Make sure your handset battery is properly
HS X REGISTERED
installed and charged.
• Put the handset in a cradle which is plugged into
AC power. After a few seconds PRESS HNDST
LOC 4 SEC ON BASE will be shown on the
screen.
• Press and hold HANDSETꢀLOCATORꢀ/INTERCOM on
the main telephone base until the INꢀUSE light
comes on (about four seconds), then release the
button.
Handset 1 Handset 2 Handset 3
• The handset will show PLEASE WAIT... for a
while.
• The handset will show HS X REGISTERED and
beep once if registration was successful.
NOTES:
Handset 4
Telephone base
1. If you are on a call, using the call log or directory, or another phone
on the same line, you cannot register a handset.
2. If the registration is not successful the display will show NOT
REGISTERED. Reset the handsets by lifting the handset out of their
cradle and then place the handset back in the cradle.
3. You can register only one handset to the base at a time.
ꢃꢂ
Appendix
Replacing a handset
If you are replacing a handset on a system that has the maximum number of
registered handsets (four) or wish to change the assigned handset number of
your registered handsets, you must first de-register the handsets, then re-regis-
ter all handsets.
To de-register all handsets
•
Press and hold HANDSETꢀLOCATORꢀ/INTERCOM on the main telephone base
until the INꢀUSE light starts to turn on then flash (about 10 seconds), then
release the HANDSETꢀLOCATORꢀ/INTERCOM button.
•
Press and release HANDSETꢀLOCATORꢀ/INTERCOM again.The INꢀUSE light will
turn off and in a few seconds, all handsets will be de-registered.
• All handsets will show NOT REGISTERED if de-registration was successful.
NOT REGISTERED
NOTES:
1. If the de-registration process was not successful you may need to reset the system and try again. To reset:
pick up the handset and press the PHONEꢀFLASH button, then press the ꢀOFFꢀCLEAR button and place
the handset back into the cradle.
2. You can only de-register handsets when the handsets and the base are not being used.
3
To re-register the handset to the telephone base, follow the registration instructions on page 43.
ꢃꢃ
Appendix
Troubleshooting
If you have difficulty with your phone, please try the suggestions below. For
(800) 222-3111. In Canada, call 1 (866) 288-4268.
•
•
Make sure the power cord is securely plugged in.
Myꢀphoneꢀ
doesn’tꢀworkꢀ
atꢀall.
Make sure that the battery wire is securely plugged into the
cordless handset.
•
•
Make sure the telephone line cord is securely and firmly
plugged into the telephone base and the telephone wall jack.
Charge the battery pack in the cordless handset for at least
ꢀꢅ hours. For optimum daily performance, return the cordless
handset to its base when not in use.
•
•
Reset the base. Unplug the unit’s electrical power. Wait for
approximately ꢀꢄ seconds, then plug it back in. Allow up to one
minute for the cordless handset and base to reset.
You may need to purchase a new battery pack, please refer to
page ꢇ of this user’s manual.
Iꢀcannotꢀgetꢀaꢀ
dialꢀtone.
•
•
First try all the suggestions above.
Move the cordless handset closer to the base. You might have
moved out of range.
•
•
Your telephone line cord might be malfunctioning. Try installing a
new line cord.
If the previous suggestions don’t work, disconnect the telephone
base from the telephone jack and connect a different phone. If
there is no dial tone on that phone either, the problem is in your
wiring or local service. Contact your local telephone company.
Iꢀcannotꢀdialꢀ
out.
•
•
First try all the suggestions above.
Make sure you have a dial tone before dialing. The cordless
handset may take a second or two to find the base and produce
a dial tone. This is normal. Wait an extra second before dialing.
•
Make sure your phone is set to the correct dial mode for the
type of service that you have (pulse or touch tone). Refer to the
installation section of this user’s manual (page ꢀꢈ) to set the
dial mode.
•
•
If the other phones in your home are having the same problem,
the problem is in your wiring or local service. Contact your local
telephone company (charges may apply).
Eliminate any background noise. Noise from a television, radio
or other appliance may cause the phone to not dial out properly.
If you cannot eliminate the background noise, first try muting
the cordless handset before dialing, or dialing from another
room in your home with less background noise.
ꢃꢄ
Appendix
Troubleshooting
•
Make sure the power cord is securely plugged into the base.
Plug the unit into a different, working electrical outlet not con-
trolled by a wall switch.
Myꢀcordlessꢀ
handsetꢀisn’tꢀ
performingꢀ
normally.
•
•
Move the cordless handset closer to the base. You might have
moved out of range.
Reset the base. Unplug the unit’s electrical power. Wait for ꢀꢄ
seconds then plug it back in. Allow up to one minute for the
cordless handset and base to reset.
•
Other electronic products can cause interference to your cord-
less phone. Try installing your phone as far away from these
types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room moni-
tors, televisions, personal computers, kitchen appliances and
other cordless phones.
•
•
Ensure that the base is powered up.
CONNECTING...
displaysꢀonꢀmyꢀ
cordlessꢀhand-
set.
Place the cordless handset in base cradle for one minute to
allow the cordless handset and base to resynchronize channels.
•
•
Move the cordless handset closer to the base. You might have
moved out of range.
If the cordless handset is in its base and the charging light does
not come on, refer to Theꢀchargeꢀlightꢀisꢀoff in this trouble-
shooting guide.
•
•
Reset the base. Unplug the unit’s electrical power. Wait for ꢀꢄ
seconds then plug it back in. Allow up to one minute for the
cordless handset and base to reset.
Other electronic products can cause interference with your
cordless phone. Try installing your phone as far away from
these types of electronic devices as possible: wireless rout-
ers, radios, radio towers, pager towers, cell phones, intercoms,
room monitors, televisions, personal computers, kitchen appli-
ances and cordless phones.
•
Charge the battery in the cordless handset for at least ꢀꢅ hours.
For optimum daily performance, return the cordless handset to
its base when not in use.
Theꢀbatteriesꢀ
willꢀnotꢀholdꢀaꢀ
charge.
•
•
•
You may need to purchase a new battery, please refer to the
battery section of this user’s manual.
Your phone might be malfunctioning. Please refer to the war-
ranty section of this user’s manual for further instruction.
If the cordless handset is in its base and the charging light does
not come on, refer to Theꢀchargeꢀlightꢀisꢀoff in this trouble-
shooting guide.
ꢃꢅ
Appendix
Troubleshooting
•
Other cordless phones and ꢇ0ꢁ.ꢀꢀ wireless routers that are
used for home computer networks also use internal radios to
communicate. The radios may interfere with one another. You
can improve the performance of your cordless phones and your
router by:
Iꢀgetꢀnoise,ꢀ
static,ꢀorꢀ
weakꢀsignalꢀ
evenꢀwhenꢀI’mꢀ
nearꢀtheꢀbase.
a. positioning your new phone as far away as possible from
any other existing cordless telephone system that is already
installed in your home to avoid the two systems interfering with
each other.
b. positioning your telephone base as far as possible from your
router, computer or any other computer devices.
c. selecting channels ꢃ through ꢀ0 for your router (refer to your
router’s user’s manual for more information).
•
Other electronic products can cause interference to your cord-
less phone. Try installing your phone as far away from the fol-
lowing electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room moni-
tors, televisions, personal computers, kitchen appliances and
other cordless phones.
•
•
Microwaves operate on the same frequency as your phone. It is
normal to experience static on your phone while the microwave
oven is operating. Do not install this phone in the same outlet or
near a microwave oven.
If your phone is plugged in with a modem or a surge protec-
tor, plug the phone (or modem/surge protector) into a different
location. If this solves the problem, re-locate your phone or
modem farther apart from one another, or use a different surge
protector.
•
•
Relocate your phone to a higher location. The phone will likely
have better reception when not installed in a low area.
If the other phones in your home are having the same problem,
the problem is in your wiring or local service. Contact your local
telephone company (charges may apply).
•
If you subscribe to DSL service and if you hear noise during
conversations and/or your caller ID features are not functioning
properly, install a DSL filter to the telephone line between the
telephone base and the telephone line jack. Contact your DSL
provider to obtain a DSL filter.
•
Disconnect the telephone base from the telephone jack, and
plug in a different telephone. If you still hear other calls, the
problem is probably in your wiring or local service. Call your
local telephone company.
Iꢀhearꢀotherꢀ
callsꢀwhileꢀ
usingꢀmyꢀ
phone.
ꢃꢆ
Appendix
Troubleshooting
•
Make sure the power cord is plugged in securely.
Iꢀhearꢀnoiseꢀinꢀ
theꢀcordlessꢀ
handset,ꢀandꢀ
noneꢀofꢀtheꢀ
keysꢀorꢀbut-
tonsꢀwork.
•
Make sure that the ringer is not turned off. Refer to the
section(s) on ringer selection in this user’s manual.
Myꢀcordlessꢀ
handsetꢀdoesꢀ
notꢀringꢀwhenꢀ
Iꢀreceiveꢀaꢀ
call.
•
Make sure the telephone line cord is plugged securely into the
telephone base and the telephone jack. Make sure the power
cord is securely plugged in.
•
•
The cordless handset may be too far from the telephone base.
Charge the battery in the cordless handset for at least ꢀꢅ hours.
For optimum daily performance, return the cordless handset to
its base when not in use.
•
•
•
•
•
You may have too many extension phones on your telephone
line to allow all of them to ring simultaneously. Try unplugging
some of the other phones.
The layout of your home or office might be limiting the operat-
ing range. Try moving the base to another location, preferably
on an upper floor.
If the other phones in your home are having the same problem,
the problem is in your wiring or local service. Contact your local
telephone company (charges may apply).
Test a working phone at the phone jack. If another phone has
the same problem, the problem is the phone jack. Contact your
local telephone company (charges may apply).
Other electronic products can cause interference with your
cordless phone. Try installing your phone as far away as pos-
sible from electronic devices such as wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room moni-
tors, televisions, personal computers, kitchen appliances and
other cordless phones.
•
•
•
Your line cord might be malfunctioning. Try installing a new line
cord.
Re-install the battery pack, and place cordless handset in base
cradle.
Wait for the cordless handset to re-establish its connection with
the base. To be safe, allow up to one minute for this to take
place.
ꢃꢇ
Appendix
Troubleshooting
•
Other electronic products can cause interference with your
cordless phone. Try installing your phone as far away from the
following electronic devices as possible: wireless routers, radi-
os, radio towers, pager towers, cell phones, intercoms, room
monitors, televisions, personal computers, kitchen appliances
and other cordless phones.
Myꢀcallsꢀfadeꢀ
outꢀorꢀcutꢀinꢀ
andꢀoutꢀwhileꢀ
I’mꢀusingꢀ
myꢀcordlessꢀ
handset.
•
•
Microwaves operate on the same frequency as your phone. It is
normal to experience static on your phone while the microwave
oven is operating. Do not install this phone in the same outlet or
near the microwave oven.
If your phone is plugged in with a modem or surge protector,
plug the phone (or modem/surge protector) into a different loca-
tion. If this solves the problem, re-locate your phone or modem
farther apart from one another, or use a different surge protec-
tor.
•
•
Relocate your telephone base to a higher location. The phone
will have better reception when not installed in a low area.
If the other phones in your home are having the same problem,
the problem is in your wiring or local service. Contact your local
telephone company (charges may apply).
•
•
•
Clean the cordless handset and base charging contacts each
month using a pencil eraser or cloth.
Theꢀchargeꢀ
lightꢀisꢀoff.
Make sure the power and line cords are plugged in correctly
and securely.
Unplug the unit’s electrical power. Wait for ꢀꢄ seconds, then
plug it back in. Allow up to one minute for the cordless handset
and base to reset.
•
•
Your phone might be malfunctioning. Please refer to the war-
ranty section of this user’s manual for further instruction.
Caller ID is a subscription service. You must subscribe to this
service from your local telephone company for this feature to
work on your phone.
MyꢀcallerꢀIDꢀ
isn’tꢀworking.
•
•
Your caller must be calling from an area that supports caller ID.
Both you and your caller’s telephone companies must use caller
ID compatible equipment.
Systemꢀdoesꢀ
notꢀreceiveꢀ
callerꢀIDꢀinfor-
mationꢀorꢀsys-
temꢀdoesꢀnotꢀ
displayꢀcallerꢀ
IDꢀinforma-
•
Make sure you subscribe to caller ID with call waiting features
services provided by your local telephone company. Caller ID
features will work only if both you and the caller are in areas
offering caller ID service, and if both telephone companies use
compatible equipment.
tionꢀduringꢀcallꢀ
waiting.
ꢃꢈ
Appendix
Troubleshooting
•
If the phone does not seem to be responding normally, try
putting the cordless handset in its base. If it does not seem to
respond, do the following (in the order listed):
Commonꢀcureꢀ
forꢀelectronicꢀ
equipment.
•
•
Disconnect the power to the base.
Disconnect the cordless handset battery, and spare battery, if
applicable.
•
•
•
Wait a few minutes.
Connect power to the base.
Re-install the battery pack, and place the cordless handset into
the base.
•
Wait for the cordless handset to re-establish its connection with
the base. To be safe, allow up to one minute for this to take
place.
•
•
•
•
If a caller leaves a very long message, part of it may be lost
when the system disconnects the call after four minutes.
Incompleteꢀ
messages.
If the caller pauses for more than seven seconds, the system
stops recording and disconnects the call.
If the system’s memory becomes full during a message, the sys-
tem stops recording and disconnects the call.
If the caller's voice is very soft, the system may stop recording
and disconnects the call.
Difficultyꢀhear-
ingꢀmessages.
•. Press.VOLUME.^.to increase speaker volume.
•
•
Make sure that the answering system is on (see page ꢂ0).
Systemꢀdoesꢀ
notꢀanswerꢀ
afterꢀcorrectꢀ
numberꢀofꢀ
rings.
If Toll Saver is activated, the number of rings changes to two
when you have new messages waiting (see page ꢂꢃ).
•
•
In some cases, the system may be affected by the ringing sys-
tem used by the local telephone company.
If the memory is full or the system is off, the system will answer
after ꢀ0 rings.
•
You need to reset the answering system clock (see page ꢂꢀ).
“CL”ꢀflashesꢀ
inꢀmessageꢀ
window.
ꢄ0
Appendix
Troubleshooting
•
•
Make sure to enter your remote access code correctly (see page
ꢂꢇ).
Systemꢀ
doesꢀnotꢀ
respondꢀꢀ
toꢀremoteꢀꢀ
commands.
Make sure you are calling from a touch tone phone. When you
dial a number, you should hear tones. If you hear clicks, the
phone is not a touch-tone telephone and cannot activate the
answering system.
•
•
The answering system may not detect the remote access
code while your announcement is playing. Try waiting until the
announcement is over before entering the code.
There may be noise or interference on the phone line you are
using. Press dial pad keys firmly.
•
•
Make sure answering system is on (see page ꢂ0).
Make sure announcement only is off.
Systemꢀdoesꢀ
notꢀrecordꢀꢀ
message.
•
•
When you record your announcement, make sure you speak in a
normal tone of voice, about ꢈ inches from the base.
Announcementꢀ
messageꢀisꢀ
notꢀclear.
Make sure there is no background noise (TV, music, etc.) while
you are recording.
ꢄꢀ
Appendix
Important safety instructions
This symbol is to alert you to important operating or servicing instructions that may appear in this
user’s manual. Always follow basic safety precautions when using this product to reduce the risk of
injury, fire, or electric shock.
Safety information
• Read and understand all instructions in the user’s manual. Observe
all markings on the product.
• Avoid using a telephone during a thunderstorm. There may be a slight
chance of electric shock from lightning.
• Do not use a telephone in the vicinity of a gas leak. If you suspect
a gas leak, report it immediately, but use a telephone away from the area
where gas is leaking. If this product is a cordless model, make sure the base
is also away from the area.
• Do not use this product near water, or when you are wet. For exam-
ple, do not use it in a wet basement or shower, or next to a swimming pool,
bathtub, kitchen sink, or laundry tub. Do not use liquids or aerosol sprays
for cleaning. If the product comes in contact with any liquids, unplug any
line or power cord immediately. Do not plug the product back in until it has
dried thoroughly.
• Install this product in a protected location where no one can trip over
any line or power cords. Protect cords from damage or abrasion.
• If this product does not operate normally, read “Troubleshooting”
in the user’s manual. If you cannot solve the problem, or if the product is
damaged, refer to the Limited Warranty. Do not open this product except as
may be directed in your user’s manual. Opening the product or reassembling
it incorrectly may expose you to hazardous voltages or other risks.
• If this product has user-replaceable batteries, replace batteries only
as described in your user’s manual. Do not burn or puncture batteries
— they contain caustic chemicals.
• If this product has a three-prong (grounding) plug or a polarized
plug with one wide prong, it may not fit in non-polarized outlets.
Do not defeat the purpose of these plugs. If they do not fit in your outlet,
the outlet should be replaced by an electrician.
CAUTION: Use only the power adapter provided with this product. To obtain a replacement, call 1 (800)
222–3111. In Canada, call 1 (866) 288-4268.
ꢄꢁ
Appendix
Important safety instructions
Especially about cordless telephones
• Privacy: The same features that make a cordless phone convenient create
some limitations.Telephone calls are transmitted between the base and the
handset by radio waves, so there is a possibility that your cordless phone
conversations could be intercepted by radio receiving equipment within
range of the cordless handset. For this reason, you should not think of
cordless phone conversations as being as private as those on cord-
ed phones.
• Electrical power: The telephone base of this cordless telephone must be
connected to a working electrical outlet.The electrical outlet should not be
controlled by a wall switch. Calls cannot be made from the handset if
the telephone base is unplugged or switched off, or if the electrical
power is interrupted.
• Potential TV interference: Some cordless telephones operate at frequen-
cies that may cause interference to TVs and VCRs. To minimize or prevent
such interference, do not place the telephone base of the cordless telephone
near or on top of a TV or VCR. If interference is experienced, moving the
cordless telephone farther away from the TV or VCR will often reduce or
eliminate the interference.
• Rechargeable batteries: This product contains either nickel-cadmium or
nickel-metal hydride rechargeable batteries. Exercise care in handling batter-
ies in order not to short the battery with conducting material such as rings,
bracelets, and keys.The battery or conductor may overheat and cause harm.
Observe proper polarity between the battery and the battery charger.
• Nickel-cadmium rechargeable batteries: Must be recycled or disposed
of properly. Do not dispose of them in household garbage. Do not burn
or puncture. Like other batteries of this type, if burned or punctured, they
could release caustic material which could cause injury.
The RBRC™ Seal means that the manufacturer is voluntarily participating in an industry program
to collect and recycle nickel-cadmium rechargeable batteries when taken out of service within the
United States. These batteries may be taken to a participating local retailer of replacement batteries or recy-
cling center. Or you may call 1 (800) 8BATTERY for locations accepting spent nickel-cadmium batteries. Nickel-
metal hydride rechargeable Batteries: Dispose of these batteries in a safe manner. Do not burn or puncture.
Like other batteries of this type, if burned or punctured, they could release caustic material which could cause
injury.
ꢄꢂ
Appendix
Important safety instructions
• Nickel-metal hydride rechargeable batteries: Dispose of these batter-
ies in a safe manner. Do not burn or puncture. Like other batteries of this
type, if burned or punctured, they could release caustic material which could
cause injury.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to 900 MHz digital cordless telephones):
Wireless Technology Research, LLC (WTR), an independent research entity, led
a multidisciplinary evaluation of the interference between portable wireless
telephones and implanted cardiac pacemakers. Supported by the U.S. Food and
Drug Administration,WTR had recommended to physicians that:
Pacemaker patients
• Should keep wireless phones at least six inches from the pacemaker.
• Should NOT place wireless phones directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless phone at the ear opposite the pacemaker.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from
other persons using wireless phones.
Especially about telephone answering systems
Two-way recording: This unit does not sound warning beeps to let the other
party know that the call is being recorded.To ensure that you are in compliance
with any federal or state regulations regarding recording a telephone call, you
should start the recording process and then inform the other party that you are
recording the call.
SAVE THESE INSTRUCTIONS
ꢄꢃ
Appendix
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical
requirements adopted by the Administrative Council for Terminal Attachments
(ACTA). The label on the back or bottom of this equipment contains, among
other things, a product identifier in the format US:AAAEQ##TXXXX. This
identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the
telephone network must comply with applicable Part 68 rules and technical
requirements adopted by ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a compat-
ible modular jack that is also compliant. An RJ11 jack should normally be used
for connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices
you may connect to your telephone line and still have them ring when you are
called. The REN for this product is encoded as the 6th and 7th characters fol-
lowing the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In
most, but not all areas, the sum of all RENs should be five (5.0) or less. For
more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired
alarm dialing equipment connected to your telephone line, ensure the con-
nection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack
until the problem has been corrected. Repairs to this telephone equipment can
only be made by the manufacturer or its authorized agents. For repair proce-
dures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company
may temporarily discontinue your telephone service. The telephone company is
required to notify you before interrupting service. If advance notice is not prac-
tical, you will be notified as soon as possible. You will be given the opportunity
to correct the problem and the telephone company is required to inform you of
your right to file a complaint with the FCC. Your telephone company may make
changes in its facilities, equipment, operation, or procedures that could affect the
proper functioning of this product. The telephone company is required to notify
you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid
compatible.
ꢄꢄ
Appendix
FCC Part 15
If this product has memory dialing locations, you may choose to store emergency
telephone numbers (e.g., police, fire, medical) in these locations. If you do store
or test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before hanging
up.
• Perform such activities in off-peak hours, such as early morning or late
evening.
This equipment has been tested and found to comply with the requirements
for a Class B digital device under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are intended to provide reason-
able protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate the
equipment.
To ensure safety of users, the FCC has established criteria for the amount of
radio frequency energy that can be safely absorbed by a user or bystander
according to the intended usage of the product. This product has been tested
and found to comply with the FCC criteria. The handset may be safely held
against the ear of the user. The telephone base shall be installed and used such
that parts of the user’s body other than the hands are maintained at a distance
of approximately 20 cm (8 inches) or more. If you choose to use a clipping
device, please make sure to only use the supplied AT&T belt clip.
ꢄꢅ
Appendix
Limited warranty
The AT&T brands are used under license. Any repair, replacement or warranty
service, and all questions about this product should be directed to:Advanced
call 1 (866) 288-4268.
1. What does this limited warranty cover?
The manufacturer of this AT&T-branded product, Advanced American
Telephones (“AAT”), warrants to the holder of a valid proof of purchase
(“CONSUMER” or “YOU”) that the product and all accessories provided by
AAT in the sales package (“PRODUCT”) are free from material defects in
material and workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with operation instruc-
tions. This limited warranty extends only to the consumer for products pur-
chased and used in the United States of America.
2. What will AAT do if the product is not free from material defects in mate-
rials and workmanship during the limited warranty period (“MATERIALLY
DEFECTIVE PRODUCT”)?
During the limited warranty period, AAT’s authorized service representative
will repair or replace, at AAT’s option, without charge, a materially defec-
tive product. If AAT repairs this product, AAT may use new or refurbished
replacement parts. If AAT chooses to replace this product, AAT may replace
it with a new or refurbished product of the same or similar design. AAT will
return repaired or replacement products to you in working condition.
AAT will retain defective parts, modules, or equipment. Repair or replace-
ment of product, at AAT’s option, is your exclusive remedy. You should
expect the repair or replacement to take approximately 30 days.
3. How long is the limited warranty period?
The limited warranty period for the product extends for ONE (1) YEAR
from the date of purchase.
If AAT repairs or replaces a materially defective product under the terms
of this limited warranty, this limited warranty also applies to repaired or
replacement products for a period of either (a) 90 days from the date the
repaired or replacement product is shipped to you or (b) the time remaining
on the original one-year limited warranty, whichever is longer.
ꢄꢆ
Appendix
Limited warranty
4. What is not covered by this limited warranty?
This limited warranty does not cover:
• product that has been subjected to misuse, accident, shipping or other
physical damage, improper installation, abnormal operation or handling,
neglect, inundation, fire, water, or other liquid intrusion; or
• product that has been damaged due to repair, alteration, or modification
by anyone other than an authorized service representative of AAT; or
• product to the extent that the problem experienced is caused by signal
conditions, network reliability or cable or antenna systems; or
• product to the extent that the problem is caused by use with non-AAT
accessories; or
• product whose warranty/quality stickers, product serial number plates or
electronic serial numbers have been removed, altered or rendered illeg-
ible; or
• product purchased, used, serviced, or shipped for repair from outside the
United States, or used for commercial or institutional purposes (including
but not limited to products used for rental purposes); or
• product returned without valid proof of purchase (see 6 below); or
• charges for installation or setup, adjustment of customer controls, and
installation or repair of systems outside the unit.
5. How do you get warranty service?
To obtain warranty service in the United States of America, call 1 (800)
222-3111 (In Canada, please dial 1 (866) 288-4268) for instructions regard-
ing where to return the product. Before calling for service, please check the
user’s manual. A check of the product controls and features may save you a
service call.
Except as provided by applicable law, you assume the risk of loss or damage
during transit and transportation and are responsible for delivery or han-
dling charges incurred in the transport of product(s) to the service location.
AAT will return repaired or replaced product under this limited warranty to
you, transportation, delivery or handling charges prepaid. AAT assumes no
risk for damage or loss of the product in transit.
If the product failure is not covered by this limited warranty, or proof of
purchase does not meet the terms of this limited warranty, AAT will notify
you and will request that you authorize the cost of repair prior to any fur-
ther repair activity. You must pay for the cost of repair and return shipping
ꢄꢇ
Appendix
Limited warranty
costs for the repair of products that are not covered by this limited warranty.
6. What must you return with the product to get warranty service?
You must:
a return the entire original package and contents including the product to
the AAT service location along with a description of the malfunction or
difficulty;
b include “valid proof of purchase” (sales receipt) identifying the product pur-
chased (product model) and the date of purchase or receipt (keep a copy
for your records); and
c provide your name, complete and correct mailing address, and telephone
number.
7. Other limitations
This warranty is the complete and exclusive agreement between you and AAT.
It supersedes all other written or oral communications related to this product.
AAT provides no other warranties for this product. The warranty exclusively
describes all of AAT’s responsibilities regarding the product. There are no
other express warranties. No one is authorized to make modifications to this
limited warranty and you should not rely on any such modification.
State Law Rights: This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Limitations:
Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the product is fit for ordinary
use) are limited to one year from date of purchase.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
In no event shall AAT be liable for any indirect, special, incidental, consequential,
or similar damages (including, but not limited to lost profits or revenue, inability
to use the product, or other associated equipment, the cost of substitute equip-
ment, and claims by third parties) resulting from the use of this product.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to you.
Please retain your receipt as your proof of purchase.
ꢄꢈ
Appendix
Technical specifications
RF frequency band
(Handset to base)
2400 MHz — 2483.5 MHz
5725 MHz — 5850 MHz
95
RF frequency band
(Base to handset)
Channels
Operating temperature
32°F — 122°F
0°C — 50°C
Telephone base voltage
(AC Voltage, 60Hz)
96 — 130 Vrms
Telephone base voltage
(AC adapter output)
9VDC @600mA
Handset voltage
3.2 — 4.7 VDC 700mAh
9VDC @200mA
Charger voltage
(AC adapter output)
Replacement battery
Battery pack (part number 80-5848-
00-00) 3.6V 700mAh
ꢅ0
Appendix
Index
A
I
AC adapter, 7
Adding new handsets, 43
Alert tones, 40
Answering calls, handset, 11; base,
12
Answering system, 30-39
Intercom, 15
Incoming call log, 26
Incoming calls, answering, handset,
11; base, 12
Indicator lights, 40
L
B
Last number redial, handset, 11;
base, 12
Low battery, 8
Battery charging, 8
Battery installation, 8
Belt clip, 10
M
C
Making calls, handset, 11; base, 12
Menus, 2
Messages, 30-39
Mute, 14
Call waiting, 13
Call transfer, 17
Caller ID, 26
add entries to phone directory, 29
delete entries, 28
dial entries, 28
N
Names,
enter into directory, 22
search for, 24
Clear voice mail indication, 19
D
O
Delete call log entries, 28
Delete redial entries, 11
Dialing,
from a caller ID record, 28
directory dialing, 25
Directory, 21
Operating range, 6
Q
Quick reference guide, 2-3
R
dial number, 25
edit entries, 25
name search, 24
new entries, 22
Receiving calls, 12
Recharging, 8
Redial, handset, 11; base, 12
Replacing a handset, 44
Ringer silencing, 14
Ring tone options, 18
E
Elapsed time, 11
Ending calls, handset, 11; base, 12
S
F
Search for names, 24
Speakerphone, 11
Flash (switchhook flash), 13
Switchhook flash, 13
H
T
Hands-free use, 11
Handset locator, 12
Headset, 10
Technical specifications, 60
Troubleshooting, 45-51
V
Volume controls, 13
ꢅꢀ
Appendix
Remote access wallet card
Use the wallet card below to help you remember commands to control your
answering system from any touch tone telephone.
Cut along dotted line
Call your phone number, then enter
your two-digit access code (preset
to 19).
Action
Remote command
Play all messages....................... 1
Play new messages................... 2
Delete the message................. 3
Delete all old messages .......... 33
Repeat or go back.................... 4
Stop.............................................
Help menu.................................
5
*5
Fold here
Skip the message...................... 6
Review announcement............ #7
Record announcement............ *7
Record memo...........................
8
Review remote access code.. #9
Change remote access code.. *9
Answer machine ON/OFF... 0
5.8 GHz CordlessTelephone/Answering System E5943B/E5944B
Copyright © 2006 Advanced AmericanTelephones. All rights reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced AmericanTelephones. Printed in China.
Copyright © 2006 Advanced AmericanTelephones. All rights reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced AmericanTelephones. Printed in China. Issue 2 AT&T 08/06.
91-000840-020-000
|