Quick start guide
AT3211-2
DECT 6.0 dual handset cordless
telephone with caller ID/
call waiting
Telephone base installation
Install the telephone base as shown below.
6. Plug the large end
of the power adapter
into a power outlet
not controlled by a
wall switch.
5. Plug the other end
of the telephone line
cord into a telephone
wall jack.
If you have DSL high
speed Internet service, a
DSL filter (not included)
is required.
1. Plug the small end
of the power adapter
into the power jack
on the bottom of the
telephone base.
ꢂ. Route the telephone
line cord through the
channel.
ꢀ. Route the power
adapter cord through
the channel.
ꢁ. Plug one end of the telephone line
cord into the telephone jack on the
bottom of the telephone base.
IMPORTANT INFORMATION
1. Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, please call the appropriate number listed below based on your
location: If you live in CT, please call 1 (800) 508-9995. If you live in AL, FL,
GA, KY, LA, MS, NC, SC or TN, please call 1 (800) 733-2355. For all other
states, please call 1 (800) 667-2118.
ꢀ. The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
ꢁ
Charger installation
Install the charger as shown below.
ꢀ. Plug the large end of the power
adapter into an electrical outlet not
controlled by a wall switch.
1. The small end of the power adapter
has been already plugged into the
jack on the bottom of the charger
at the factory. Check to make sure it
clicks firmly into place.
IMPORTANT INFORMATION
1. Use only the power adapter(s) supplied with this product. To order a replacement
power adapter, please call the appropriate number listed below based on your
location: If you live in CT, please call 1 (800) 508-9995. If you live in AL, FL,
GA, KY, LA, MS, NC, SC or TN, please call 1 (800) 733-2355. For all other
states, please call 1 (800) 667-2118.
ꢀ. The power adapters are intended to be correctly oriented in a vertical or floor mount
position. The prongs are not designed to hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
ꢂ
Battery installation & charging
Install the battery as shown on the next page. Once you have installed the
battery, the screen indicates the battery status (see table below). If necessary,
place the handset in the telephone base to charge the battery. For best
performance, keep the handset in the charger when not in use. The battery is
fully charged after 16 hours of continuous charging. See the table on page 5ꢁ
of the user’s manual for battery operating times.
If the screen is blank, you need to charge the handset without interruption for
at least 10 minutes to give the handset enough charge to use the telephone
for a short time. The screen shows LOW BATTERY and the backlight is off until
you have charged the battery without interruption for at least one hour. The
following table summarizes the battery charge indicators and actions to take.
Battery indicators
Battery status
Action
The screen is blank.
Battery has no charge and
the handset cannot be
used.
Charge without interruption until the
screen shows LOW BATTERY (at least
10 minutes).
The screen shows
PLACE IN CHARGER
and flashes.
Battery has very little
charge and the handset
cannot be used.
Charge without interruption until the
screen shows LOW BATTERY (at least
four minutes).
The screen shows LOW
Battery has enough charge
Charge without interruption until the
BATTERY, flashes, and to be used for a short time. screen shows HANDSET X (at least one
the handset beeps.
hour).
The screen shows
Battery is charged.
To keep the battery charged, place it
in the telephone base or charger when
not in use.
HANDSET X.
NOTE: If you are on a phone call in low battery mode, you hear four short beeps every
minute.
5
Battery installation & charging
Step 1
Step 2
Plug the battery
connector securely
into the socket
inside the handset
battery compartment,
matching the color-
coded label. Insert the
supplied battery with
the label THIS SIDE UP
facing up as indicated.
Align the cover flat
against the battery
compartment, then
slide it upwards
until it clicks into
place.
CHARGE light
Step 3
Charge the handset by placing it
face forward in the telephone base
or charger. The CHARGE light is on
when charging.
IMPORTANT INFORMATION
1. Use only the supplied rechargeable battery or replacement battery. To order, please
call the appropriate number listed below based on your location: If you live in CT,
please call 1 (800) 508-9995. If you live in AL, FL, GA, KY, LA, MS, NC, SC or
TN, please call 1 (800) 733-2355. For all other states, please call
1 (800) 667-2118.
ꢀ. If you do not use the handset for a long time, disconnect and remove the battery to
prevent possible leakage.
6
Quick reference guide - handset
qCID/VOL
Press qCID to display caller ID
history.
PLAY/MENU/SELECT
Press to play voicemail messages.
Press to show the menu.
Press to scroll down while in
menus.
While entering names or
numbers, press to move the
cursor to the left.
While in the menu, press to
select an item or save an entry or
setting.
CHARGE indicator
On when the handset is charging
in the telephone base or charger.
Press to decrease the listening
volume when on a call.
ERASE
SKIP
Press to erase a voicemail
message.
Press to skip to the next
voicemail message.
VOICEMAIL
p
/VOL
Press to dial to the voicemail
provider for accessing to your
voicemail messages.
Press DIRp to show directory
entries.
Press to scroll up while in menus.
OFF/CLEAR
While entering names or
numbers, press to move the
cursor to the right.
Press to increase the listening
volume when on a call.
During a call, press to hang up.
While in a menu, press to cancel
an operation, back up to the
previous menu, or exit the menu
display.
Press and hold while the
(Speakerphone)
telephone is not in use to erase
the missed calls indicator.
Press to switch between
speakerphone and handset.
#
/FLASH
Press repeatedly to display other
dialing options when reviewing a
call log entry.
Press to make or answer a call.
During a call, press to answer an
incoming call when you receive a
call waiting alert.
INT
Press to begin an intercom
1
conversation or to transfer a call.
While reviewing a call log
entry, press repeatedly to add
or remove 1 in front of the
telephone number before dialing
or saving it in the directory.
MUTE/REMOVE
During a call, press to mute the
microphone.
While reviewing the caller ID
history, the directory or the
redial memory, press to delete an
individual entry.
REDIAL/PAUSE
Press repeatedly to view the last
five numbers dialed.
While predialing, press to delete
digits.
While entering numbers,
press and hold to insert a dialing
pause.
ꢃ
Quick reference guide - handset
Main menu
>Highlights a menu
item.
Main menu
DIRECTORY
CALL LOG
RINGER VOLUME
RINGER TONE
KEY TONE
>DIRECTORY
CALL LOG
LCD LANGUAGE
SET DATE/TIME
CLR VOICEMAIL
SET VOICEMAIL
HOME AREA CODE
Menu
Using menus
Press PLAY/MENU/SELECT to show the first
menu item, DIRECTORY.
Press qCID or
p
to scroll through menu
items.
Press PLAY/MENU/SELECT to select or save
changes to a highlighted menu item.
Press OFF/CLEAR to cancel an operation,
back up to the previous menu, or exit the
menu display.
ꢄ
Quick reference guide - telephone base
VOICEMAIL indicator
IN USE indicator
Flashes when you have new
voicemail. Voicemail service
is offered by your local
telephone company.
On when the handset is
in use or when you are
registering a handset.
Flashes when another
telephone on the same line
is in use, or when you are
de-registering handset(s)
from the telephone base.
Flashes quickly when there
is an incoming call.
FIND HANDSET
Press to make handsets
beep so you can locate
them.
ꢅ
© 2009 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 4 AT&T 09/09.
|