AT&T
®
MERLIN
COMMUNICATIONS SYSTEM
USER’S GUIDE:
MODELS 1030 AND 3070
WITH FEATURE MODULE 5
Available Features
Tailor your voice terminal to
meet your individual needs
by programming available
buttons
features.
with
custom
Use line buttons to call peo-
ple who aren’t connected to
your MERLIN system.
Touch Intercom-Ring or
Intercom-Voice to use the
MERLIN system Intercom
feature.
Use Conference, Drop,
Transfer, and Hold for effi-
cient call-handling.
Test your voice terminal and
program its features by
sliding the T/P switch to T
(Test) or P (Program).
Touch Speaker for On-Hook
Dialing and for Group
Listening.
Adjust the volume of your
voice terminal’s speaker
and ringing using the
volume control.
Touch Recall to disconnect
a call without hanging up
your handset.
Call your MERLIN system
attendant for messages
when the light is on next to
Message. Use Message (in
program mode) to set your
voice terminal for making
data calls and voice calls
simultaneously.
Read on to learn how to use these features...and many more.
2
Key to Symbols
The following symbols are used throughout this guide to illustrate the steps for using your MERLIN system voice terminal.
After you are familiar with the steps, use the symbols to remind you how to perform each procedure.
555-1234
Slide the T/P switch to
the P position.
Lift your handset.
Touch a button.
(The symbols for buttons
are shaded and labeled
to look like the buttons
on your voice terminal.)
Transfer
Don’t lift your handset.
Slide the T/P switch to
the center position.
Dial a number.
(This can be an outside
number, an intercom
number, a feature code,
or an account number.)
Hang up your handset.
Since each symbol represents one action, a sequence of two or more symbols illustrates a procedure. For example:
Intercom
Ring
+
+
intercom
number
3
means lift your handset, touch Intercom-Ring, and dial an intercom number.
Placing Calls
With your MERLIN® system, you can place two types of calls:
outside calls and intercom calls.
OUTSIDE CALLS
To call someone who is not connected to your MERLIN system:
●
+
Lift your handset.
outside
number
The MERLIN system automatically selects an available outside
line.
●
Dial the number.
NOTE: When the red light is on next to a line button, it means
you are using that line or will get that line if you lift your hand-
set. When you lift your handset to place a call, the green light
goes on next to the red light to show that the line is busy.
To select a specific outside line:
555-1234
+
●
Touch the button for that line.
●
Lift your handset.
4
Button Access and Dial Access to Line Pools
Your MERLIN system may be “pooled,” meaning some or all
of your outside telephone lines are grouped into one or more
pools (for example, a pool of local lines, a pool of WATS lines,
and a pool of Foreign Exchange lines). You make outside calls
on pooled lines in one of two ways, depending on how your
system is set up: either you touch a button for direct access to
a line in a pool (Button Access), or you touch a button and then
dial a code for access to a specific line pool (Dial Access).
Ask your system administrator if your system is pooled. If it is,
find out whether you have Button Access or Dial Access to Line
Pools. If you have Dial Access, ask for a list of codes for the
pools.
To make an outside call with Button Access to Line Pools:
●
WATS
Touch the button for the line pool you want.
+
+
● Lift your handset.
outside
number
● When you hear a dial tone, dial the telephone number you
want.
To make an outside call with Dial Access to Line Pools:
●
Touch a Pool Access button.
●
Lift your handset.
Pool Access
+
+
+
●
When you hear a dial tone, dial a code for the line pool you
want.
line
pool
code
outside
number
●
When you hear another dial tone, dial the telephone
number you want.
5
NOTE: Ask your system administrator if your system has
Automatic Route Selection (ARS). If it does, follow the procedure
for making outside calls in the next section, “Automatic Route
Selection.” Neither of the above procedures works for you if your
system has ARS.
Automatic Route Selection
If you have Pool Access buttons, your MERLIN system may
have Automatic Route Selection (ARS). Ask your system admin-
istrator if your system has ARS.
ARS automatically selects an administered route for each out-
side call you make using a Pool Access button. For example,
if you touch Pool Access and dial a long distance number, ARS
may select WATS as the route for your call. In this case, ARS
automatically routes your call onto a WATS line.
To place an outside call using ARS:
●
Touch a Pool Access button.
This signals ARS to expect an outside call.
●
Pool Access
Lift your handset.
Dial the outside telephone number you want.
+
+
●
outside
number
You hear beeps instead of Touch-Tones or rotary clicks as you dial.
●
Wait a few moments.
If you hear a faster busy signal than normal:
●
Touch the same Pool Access button you used to begin your
call.
6
If you hear a fast MERLIN system busy signal:
●
Hang up and redial in a few moments using the Pool Ac-
cess procedure or the Saved Number Redial feature (see
page 23).
NOTE: For ARS to work, you must dial a “1” before dialing a
long distance number, even if you do not normally do so.
Line Request
If you are waiting to use a line that is busy, you can have the
MERLIN system signal you when the line is free:
●
Without lifting your handset, touch the button for the busy
line.
555-1234
The red light next to the button goes on.
+
●
When you hear the voice terminal ring briefly, indicating
the line is available, lift your handset.
You cancel your Line Request when you touch another line but-
ton or when you receive or place another call.
INTERCOM CALLS
Each voice terminal connected to your MERLIN system has a
unique 2-digit intercom number. You dial intercom numbers to
place either ringing or announced intercom calls to people con-
nected to your MERLIN system.
Ringing Intercom Calls
Place ringing intercom calls when you want to have a two-way
conversation with people connected to your MERLIN system.
Your calls ring at their voice terminals, and your coworkers lift
their handsets to hear you and to talk with you.
7
To place a ringing intercom call:
●
Touch Intercom-Ring.
Intercom
Ring
+
+
●
Lift your handset.
intercom
number
●
Dial a 2-digit MERLIN system intercom number.
Announced Intercom Calls
When you place an announced intercom call, your coworker
hears your voice through the voice terminal speaker. If your
coworker wants to respond to your announcement, he or she
speaks through the handset to talk with you. Your voice an-
nouncements do not interrupt your coworkers’ outside calls, so
if you need to, you can make an announcement to someone who
is busy on another line.
To announce your call through another person’s voice terminal
speaker:
●
Touch Intercom-Voice.
Intercom
Voice
●
Lift your handset.
+
+
●
intercom
number
When you hear a beep, speak into your handset.
●
If you try to place an announced intercom call to a voice terminal
that is programmed to prevent voice announcements (see
“Voice Announcement Disable,” page 45), your call becomes
a ringing intercom call.
8
Answering Calls
To answer a call:
●
Lift your handset.
You are automatically connected to the incoming call.
You can tell what kind of call you’re receiving by the way your
voice terminal rings.
=
=
=
Intercom
Transferred
two short and one long ring
one long ring
one short and one long ring
You may personalize these rings to distinguish the ringing of
your voice terminal from that of others in your office (see “Per-
sonalized Ringing,” page 44).
9
Fixed Features
Fixed features are the features assigned to the permanently
labeled buttons on your voice terminal.
HOLD
Hold
To put a call on hold:
Pause
●
Touch Hold.
When you put a call on hold, the green light next to the call’s
line button flashes rapidly. If someone else puts a call on hold
from another voice terminal, the green light flashes slowly next
to the call’s line button on your voice terminal.
To take a call off hold:
555-1234
●
Lift your handset.
●
Touch the held call’s button.
When you leave a call on hold for more than a minute, your voice
terminal rings to remind you the call is still on hold.
TRANSFER
To transfer an outside call from your voice terminal to another
person in your MERLIN system or to a Group Call Distribution
group (see “Group Call Distribution,” page 30):
Transfer
+
+
●
Touch Transfer.
intercom
number
●
Dial the intercom number for the person or dial the Group
Call Distribution code.
Hang up.
10
●
If the call is not answered within a few rings, it returns to your
voice terminal.
Transfer with Voice Announcement
To announce a transferred call:
Transfer
Intercom
Voice
+
+
+
●
Touch Transfer.
● Touch Intercom-Voice.
●
Dial the intercom number of the voice terminal to which you
want to transfer the call.
● Announce the call through your handset.
intercom
number
●
Hang up.
You cannot transfer with voice announcement to a Group Call
Distribution group (see “Group Call Distribution,” page 30).
CONFERENCE
You can place a call that includes up to two people outside your
MERLIN system, two people inside, and you. To set up a con-
ference call when you already have one of the participants on
the line:
●
Touch Conference.
Conference
●
Touch a line button (or Intercom-Ring, or Intercom-Voice).
555-1234
+
+
●
Dial an outside number (or an intercom number).
outside
number
●
When the other person answers, announce the conference
call.
Repeat this procedure for each person you intend to include in
the conference.
11
If you don’t want a participant to listen as you set up the rest of
the conference call, touch Hold before repeating this procedure.
To take the person off hold:
Conference
555-1234
+
●
Touch Conference.
● Touch the button for the line you put on hold.
If you have several lines on hold, repeat this procedure for each
one.
Hold
Pause
To remove yourself from a conference call without ending the
call:
●
Touch Hold.
To rejoin the call:
555-1234
●
Touch a button associated with a line active in the call.
Drop
To disconnect a busy or unanswered line when you’re trying to
set up a conference call, or to disconnect one person at a time
from a conference call:
Drop
●
555-1234
Touch Drop.
+
Stop
●
Touch the button of the line to disconnect.
If you’re setting up a conference call, remember to touch Con-
ference again before trying to add another call to the
conference.
NOTE: You must use the Drop feature when you want to discon-
nect one person from a conference call. If you press the switch-
hook, you end the call.
12
SPEAKER
You can use your voice terminal’s speaker to monitor a call as
you dial it, to monitor a call on hold, and to let a group listen to
your conversation.
On-Hook Dialing
Instead of using your handset to listen while you place a call,
you can use your voice terminal’s built-in speaker:
Speaker
●
Touch Speaker.
+
+
The green light next to Speaker goes on, and you hear a dial tone
through your voice terminal’s speaker
outside
number
●
Dial the number.
●
When you hear the other person answer, lift your handset.
Speaker
If the line is busy, or if you get no answer:
●
Touch Speaker to cancel the call.
You can use On-Hook Dialing any time instructions tell you to
lift your handset before dialing. Simply touch Speaker instead
of lifting your handset.
Monitor-on-Hold
When you’ve been put on hold, you can hang up and continue
working while you wait for the person to return to the call:
Speaker
●
Touch Speaker.
+
+
●
Hang up.
●
When you hear the other person return to the call, lift your
13
handset.
Group Listening
Speaker
●
Without hanging up your handset, touch Speaker.
You can speak to the other person only through your handset
unless you have a Hands-Free Unit (see “Hands-Free Unit,”
page 50).
NOTE: Before hanging up, touch Speaker again. This prevents
a squeal from the speaker as your handset comes close to it.
MESSAGE
Your MERLIN system attendant can let you know that a
If you have a 5-button voice terminal, you do not have a Message
button. However, you can program a button to act as a Message
button (see “Basic Programming Instructions,” page 16, and the
Feature Programming Chart on page 55).
To turn off the message light:
Message
●
Touch Message.
You can set up a messaging system between your voice terminal
and another voice terminal using the Notify feature (see “Notify,”
page 17). The Notify feature works independently of the
Message feature.
14
Custom Features
Custom features are features that you select and program for
your voice terminal. The basic programming instructions below
describe the procedure you follow to program features on your
voice terminal. You can program most custom features on the
available buttons on your voice terminal; however, if you have
a limited number of feature buttons available, you can dial
special codes to use many of the custom features. Read through
each feature’s description before you program it on your voice
terminal.
BASIC PROGRAMMING INSTRUCTIONS
Using the following simple procedure, you can assign and
reassign custom features to any buttons that are not already
assigned outside lines, intercom lines, or fixed features:
●
Label the button(s) you want to program.
●
Slide the T/P (Test/Program) switch on the left side
of the voice terminal toward you to the P (Program)
position.
The voice terminal rings every 5 seconds to remind you that
you are programming and that you cannot place or receive
calls.
Home
+
+
+
programming
code
●
Without lifting your handset, touch the button you
want to program.
●
Dial the feature’s programming code and any other
numbers required.
16
●
●
If you want to program other buttons, repeat the two
previous steps.
Slide the T/P switch to the center position.
NOTE: If you make a mistake entering a programming code,
simply touch the button again and reenter the code.
The following feature descriptions include feature programming
codes and brief programming instructions. For example:
To program:
●
●
T/P to P
●
Touch the button Dial *84
●
T/P to center
means slide the T/P switch toP, touch the button you want to
program, dial the programming code (in this case, *84), and
slide the T/P switch to the center position.
NOTIFY
Use the Notify feature to set up a direct messaging system with
another voice terminal. With this feature, you program a Send
button to turn on a Notify light next to the corresponding Receive
button on the voice terminal of someone for whom you often
have messages. For example, a secretary can notify his or her
boss that a message is waiting. You can program multiple Send
and Receive buttons. For each Send button you program on
your voice terminal, there must be a Receive button that has
been programmed at the receiving voice terminal, and vice
versa. Be sure to label the buttons so you can identify the per-
son notifying you or receiving your notification.
17
Notify Send
To program:
●
T/P to P
+ the intercom number of the person you
want to notify T/P to center
●
Touch the button
●
Dial *87
●
To notify another voice terminal of a message:
●
Touch the Send button.
The green light next to your Send button goes on.
The green light next to the Receive button on the other voice
terminal goes on.
Send John
NOTE: Remember that for each Send button you
program on your voice terminal, there must be a
Receive button programmed on the receiving voice
terminal.
To turn off the green light next to the Send button:
●
Touch the Send button.
The green light next to the Send button on your voice ter-
minal goes off.
Send John
The green light next to the Receive button on the other voice
terminal goes off.
Notify Receive
To program:
●
T/P to P
+ the intercom number of the person
notifying you T/P to center
●
Touch the button Dial *88
●
●
A green light next to the Receive button indicates there is a
message waiting for you.
18
To turn off the green light next to the Receive button:
●
Touch the Receive button.
The green light next to your Receive button goes off.
The green light next to the Send button on the other voice
terminal also goes off.
Receive Susan
OUTSIDE AUTO DIAL
Use the Outside Auto Dial feature for one-touch dialing of fre-
quently used telephone numbers, account numbers, or PBX,
Centrex, or Custom Calling feature codes. You can include up
to 16 numbers and special characters in an Auto Dial sequence.
To program:
●
T/P to P
●
Touch the button Dial *90
●
+ an outside number, an account
number, or a PBX, Centrex, or Custom
Calling feature code T/P to center
●
To use the Outside Auto Dial feature:
●
Without lifting your handset, touch the Outside Auto
Dial button for the number you want to dial.
Home
+
+
Your voice terminal speaker goes on, and you hear dialing.
●
When you hear the other person answer, lift your
handset.
If the line is busy or if no one answers:
Speaker
●
Touch Speaker to cancel the call.
19
Special Characters in Programmed Dialing Sequences
You may occasionally need to program a pause, stop, or switch-
hook flash into an Outside Auto Dial or Speed Dial sequence,
or you may need to switch from rotary to Touch-Tone signals in
the middle of a programmed dialing sequence. To do so, you
need to enter the following special characters when you pro-
gram the sequence.
Pause. To program a pause (1.5 seconds) into a dialing se-
quence (for example, between a pool access code and an out-
side telephone number):
Hold
Drop
●
Touch Hold (Pause).
Pause
Stop. To program a stop into a dialing sequence (for example,
to program a stop between an alternate long distance telephone
number and your access code):
●
Touch Drop (Stop).
Stop
To resume the dialing sequence after the stop, touch the Auto
Dial button or dial the Speed Dial code again.
Touch-Tone Enable. To program Touch-Tone Enable into a dial-
ing sequence (for example, to use a credit card authorization
service):
Transfer
●
Touch Transfer.
Switchhook Flash. To program a switchhook flash into a dial-
ing sequence (for example, if you program a button with a PBX,
Centrex, or Custom Calling feature code):
20
●
●
Touch Recall.
Recall
Hold
Pause
+
Touch Hold (Pause).
AUTO INTERCOM
Use the Auto Intercom feature for one-touch dialing of intercom
numbers.
If you program this feature on a button with lights, the green light
next to the button goes on when the person at that intercom uses
his or her voice terminal or uses the Do Not Disturb feature. You
can use an Auto Intercom button whenever you would usually
dial an intercom number.
●
T/P to P
+ a MERLlN system intercom number
T/P to center
●
Touch the button
●
Dial *91
To program:
●
Ringing Intercom Calls
To place a ringing intercom call with one touch:
●
Touch the Auto Intercom button for the intercom number
John
+
you want to dial.
Your voice terminal speaker goes on, and you hear ringing.
NOTE: If the red light next to Intercom-Voice is on, touch
Intercom-Ring before you touch the Auto Intercom button.
●
When you hear the other person answer, lift your handset.
Speaker
If the line is busy or if no one answers:
●
Touch Speaker to cancel the call.
21
Announced Intercom Calls
To place an announced intercom call:
●
If the red light next to it is not already on, touch
Intercom-Voice.
Touch the Auto Intercom button for the intercom number
you want to dial.
Intercom
Voice
John
●
+
+
Your speaker goes on, and you hear a beep.
●
Lift your handset and begin speaking.
PERSONAL SPEED DIAL
(5- and 10-button voice terminals only)
When you don’t have many buttons available to program for Out-
side Auto Dial, you can use the programming instructions below
to assign a 3-character Personal Speed Dial code (#01 through
#22) to each telephone number, account number, or PBX, Cen-
trex, or Custom Calling code you frequently dial. You can assign
a sequence containing up to 16 numbers and special characters
to a Personal Speed Dial code.
●
T/P to P
●
Dial a Personal Speed Dial
Dial *90 + a
To program:
code (#01 through #22)
●
telephone number, an account number,
or a PBX, Centrex, or Custom Calling
feature code T/P to center.
●
To place a call using a Personal Speed Dial code:
+
●
Lift your handset.
personal
speed dial
code
●
Dial a Personal Speed Dial code (#01 through #22).
22
SYSTEM SPEED DIAL
System Speed Dial is similar to Personal Speed Dial in that
3-character codes (#60 through #99) represent frequently dialed
telephone numbers. However, you do not assign the codes to
telephone numbers; your system administrator is the only one
who can assign a System Speed Dial code to a telephone
number, and everyone connected to your MERLIN system can
use those System Speed Dial codes.
To place a call using a System Speed Dial code:
●
Lift your handset.
+
system
speed dial
code
●
Dial a System Speed Dial code (#60 through #99).
Using a System Speed Dial Button
You can use the instructions below to program buttons with fre-
quently used System Speed Dial codes.
To program:
●
T/P to P
+ a System Speed Dial code (60 through
99—do not enter the #) T/P to center
●
Touch the button
●
Dial *95
●
To place a call using a System Speed Dial button:
●
Lift your handset.
Denver Office
+
●
Touch the button for the System Speed Dial code you want
to dial.
SAVED NUMBER REDIAL
Use the Saved Number Redial feature to save a number for
quick redialing later. (The number cannot contain a pause, a
23
stop, a Touch-Tone enable, or a switchhook flash.) If you have
a 34-button voice terminal, use the instructions below to pro-
gram a button with the Saved Number Redial feature. If you have
a 5- or 10-button voice terminal, there’s no need for any special
programming. You simply dial a code to use this feature, thus
saving a feature button for a custom feature that requires a
button.
●
●
T/P to P
●
Touch the button Dial *74
●
To program:
T/P to center
If you program a Saved Number button, you can save a number
with the touch of a button. So when you dial a number you want
to redial later:
Saved Number
●
Before hanging up, touch Saved Number.
When you want to save a new number, repeat the above
procedure.
To redial the number later:
Saved Number
+
●
Lift your handset.
●
Touch Saved Number.
Using a Dial Code (5- and 10-button voice terminals only)
When you dial a number you want to save for later redialing:
●
Before hanging up, dial #23.
#23
To redial the number you saved:
●
Lift your handset.
+
●
Dial #23.
24
#23
LAST NUMBER REDIAL
Use the Last Number Redial feature to redial the number you
dialed most recently. (The number cannot contain a pause, a
stop, a Touch-Tone enable, or a switchhook flash.) If you have
a 34-button voice-terminal, you can follow the programming in-
structions below to program this feature onto a button. If you
have a 5- or 10-button voice terminal, you can dial a code to use
this feature and save a button for another use.
To program:
●
●
T/P to P
T/P to center
●
Touch the button Dial *73
●
If you program a Last Number button, you can redial the number
you most recently called with the touch of a button:
●
Lift your handset.
Last Number
+
+
●
Touch Last Number.
Using a Dial Code (5- and 10-button voice terminals only)
To redial a number using the Last Number Redial code:
Lift your handset.
●
●
Dial #24.
#24
MANUAL SIGNALING
Use the Manual Signaling feature to generate a beep at a
coworker’s voice terminal. Assign a Manual Signaling button to
each person you want to signal.
●
T/P to P
●
Touch the button
●
Dial * 6
To program:
+ an intercom number
●
T/P to center
25
To signal a coworker:
●
Without lifting your handset, touch a Manual Signaling
button.
Signal Mary
+
You can also touch a Manual Signaling button to signal some-
one while you have an outside call in progress. If you program
this feature on a button with lights, the green light next to the
button goes on when your coworker uses his or her voice ter-
minal or uses the Do Not Disturb feature.
LOUDSPEAKER PAGE
If you have a loudspeaker paging system, you can make an-
nouncements using your voice terminal. Your system may have
as many as three paging zones; you can choose to make an an-
nouncement to one or all of the zones.
If you have available feature buttons, you can use the instruc-
tions below to program a button for each loudspeaker paging
zone. However, it isn’t necessary to program a button for
loudspeaker paging. You may dial a code instead.
To program:
●
T/P to P
●
Touch the button
●
Dial *91
+ a paging zone code (80=all zones,
81=zone 1, 82=zone 2, 83=zone 3)
to center
●
T/P
26
When you have a Loudspeaker Page button for the zone you
want to page:
●
Touch the Loudspeaker Page button for the zone you want
Lsp. Page 1
to page.
+
●
When you hear a beep, lift your handset and make your
announcement.
Using a Dial Code
To page a zone using a dial code:
●
Touch Intercom-Voice or Intercom-Ring.
●
Lift your handset.
Dial one of the following codes:
●
Intercom
Voice
+
+
80 for all zones
loudspeaker
page
zone 1
zone 2
zone 3
81
82
83
code
●
When you hear a beep, speak into your handset.
When you hang up, you turn off the loudspeaker.
27
GROUP PAGE
Use the Group Page feature to make announcements through
the speakers in groups of 10 voice terminals specified by your
system administrator. Your system can have as many as seven
groups. You can use the instructions below to program buttons
for the groups you want to page. Or, you can save your feature
buttons for other uses and dial a code to use the Group Page
feature.
●
T/P to P
●
Touch the button Dial *91
●
To program:
+ a Group Page code (841=group 1,
842=group 2, 843=group 3, 844=
group 4, 845=group 5, 846=group 6,
847=group 7) T/P to center.
●
To use a Group Page button to make an announcement through
a group of voice terminal speakers:
●
Touch the Group Page button for the group you want to
Group Page 1
+
page.
●
When you hear a beep, lift your handset and make your
announcement.
28
Using a Dial Code
To page a group using a dial code:
●
Touch Intercom-Voice or Intercom-Ring.
●
Lift your handset.
●
Dial the code for the group you want to page.
841 for group 1
842
843
844
845
846
847
group 2
group 3
group 4
group 5
group 6
group 7
Intercom
Voice
+
+
group
page
code
●
When you hear a beep, speak into your handset.
29
GROUP CALL DISTRIBUTION
Use the Group Call Distribution feature to place an intercom call
or transfer an outside call to a specific group of voice terminals.
When you place or transfer a call to a Group Call Distribution
group—for example, the Sales Department—the system selects
a voice terminal in the group to receive your call. Your system
administrator can assign up to 15 voice terminals to a group.
Your system can have as many as six groups. You can use the
instructions below to program buttons for the groups you want
to call. Or, you can save your feature buttons for other uses and
dial a code to use the Group Call Distribution feature.
●
T/P to P
●
Touch the button Dial *91
●
To program:
+ a Group Call Distribution code
(850=group 1, 851=group 2, 852=
group 3, 853=group 4, 854=group 5,
855=group 6)
●
T/P to center
To Place an Intercom Call
To use a Group Call Distribution button to call a group:
●
Touch the Group Call Distribution button for the group you
want to call.
Group Call
Sales
+
The system selects a voice terminal in the group to receive your call.
●
When you hear a beep, lift your handset.
Using a Dial Code
To call a group using a dial code:
●
Touch Intercom-Voice or Intercom-Ring.
●
Lift your handset.
30
●
Dial the code for the group you want to call.
850 for group 1
group 2
group 3
group 4
group 5
group 6
851
852
853
854
855
Intercom
Ring
+
+
group call
distribution
code
●
When you hear a beep or when the person answers, speak
into your handset.
To Transfer an Outside Call
To transfer a call to a Group Call Distribution group:
Transfer
●
Group Call
Sales
Touch Transfer.
+
+
●
Touch the Group Call Distribution button for the group to
whom you want to transfer the call.
The system selects a voice terminal in the group to receive the call.
NOTE: If your system is administered for One-Touch Transfer,
you do not have to touch Transfer to transfer an outside call (see
“One-Touch Transfer or One-Touch Hold with Call Announce-
ment,” page 32).
Using a Dial Code
To transfer an outside call to a Group Call Distribution group
using a dial code:
Transfer
●
Touch Transfer.
+
+
●
Dial the appropriate group code.
group call
distribution
code
31
●
Hang up.
ONE-TOUCH TRANSFER OR ONE-TOUCH HOLD WITH
CALL ANNOUNCEMENT
The way in which you use Auto Intercom buttons and Group Call
Distribution, Loudspeaker Page, or Group Page buttons with
outside calls depends on whether your system is administered
for One-Touch Transfer or One-Touch Hold with Call Announce-
ment. Ask your system administrator which feature is admin-
istered for your system, then follow the appropriate procedure
below.
One-Touch Transfer
If your system is administered for One-Touch Transfer and you
have an Auto Intercom or Group Call Distribution button for the
person or group to whom you want to transfer an outside call,
you can transfer the call with one touch:
●
Touch the button for the person or group to whom you are
transferring the call.
John
+
●
Hang up.
One-Touch Hold with Call Announcement
If your system is administered for One-Touch Hold with Call
Announcement and you have an Auto Intercom, Group Call
Distribution, Loudspeaker Page, or Group Page button for the
person or group you want to notify, you can put the outside call
on hold and place an announced intercom call with one touch:
●
Touch the button for the person or group whom you want
to notify.
John
The call is put on hold. The announced intercom call is placed.
●
When you hear a beep, speak into your handset.
32
son or group answer the call by using the Line Pickup feature.
NOTE: If you try to place an announced intercom call to a voice
terminal that is programmed to prevent voice announcements
(see “Voice Announcement Disable,” page 45), your call
becomes a ringing intercom call.
AUTO ANSWER-ALL
If you have a modem or answering machine connected to your
voice terminal, program an Auto Answer-All button so you can
set your answering equipment to go on automatically when you
receive ringing calls. Program this feature on a button with lights.
To program:
●
●
T/P to P
T/P to center
●
Touch the button Dial *75
●
To have calls answered automatically:
Auto Answer-
All
●
Touch Auto Answer-All.
The green light next to the button goes on.
To go back to answering calls yourself:
Auto Answer-
All
●
Touch Auto Answer-All.
The green light next to the button goes off.
33
AUTO ANSWER-INTERCOM
If you have an optional Hands-Free Unit connected to your voice
terminal, program an Auto Answer-Intercom button so you can
set your Hands-Free Unit to go on automatically when you
receive intercom calls. Program this feature on a button with
lights.
To program:
●
●
T/P to P
●
Touch a button Dial *70
●
T/P to center
To have intercom calls answered automatically:
Auto Answer-
Intercom
●
Touch Auto Answer-Intercom.
The green light next to the button goes on.
To go back to answering calls yourself:
●
Touch Auto Answer-Intercom.
Auto Answer-
Intercom
The green light next to the button goes off.
CALL COVERAGE
Use the Call Coverage feature to receive calls directed to
another voice terminal. Follow the instructions below to program
a Cover button for each person you want to cover (you can have
up to six Cover buttons). Program this feature on buttons with
lights.
●
T/P to P
the intercom number of the person you
want to cover T/P to center
●
Touch a button
●
Dial *4 +
To program:
●
34
When you receive a call for a person you’re covering, your voice
terminal rings and the green light next to that person’s Cover
button flashes. To answer the call:
●
Lift your handset.
You can program Cover buttons so covered calls ring im-
mediately, after a delay, or don’t ring at all (see “Programmable
Line Ringing,” page 43). If you program a Cover button not to
ring, the green light still flashes next to the Cover button when
a call comes in, and you can still answer the call:
Cover John
●
+
Touch the Cover button.
Lift your handset.
●
If someone is covering your calls, you may want to program your
voice terminal to ring after a delay, but your voice terminal can-
not be set to “no ring.” If you share lines with another person,
use Programmable Line Ringing to cover one another’s calls
(see “Programmable Line Ringing,” page 43).
Coverage Inhibit
With a Coverage Inhibit button, you can temporarily turn off the
Call Coverage feature so your calls don’t ring at another voice
terminal. Program this feature on a button with lights.
To program:
●
●
T/P to P
●
Touch the button Dial *77
●
T/P to center
To stop Call Coverage:
●
Touch Coverage Inhibit.
Coverage
Inhibit
35
The green light next to the button goes on.
To restore Call Coverage:
●
Touch Coverage Inhibit again.
Coverage
Inhibit
The green light next to the button goes off.
Using Call Coverage and Coverage Inhibit to Forward Calls
You can set up a call forwarding feature using Call Coverage
and Coverage Inhibit. If you are often away from your voice ter-
minal, but near another voice terminal connected to your
MERLIN system:
●
Program a Cover button on the other voice terminal to cover
your calls.
Calls to you ring at the other voice terminal as well as at your own.
When you want calls to ring only at your voice terminal:
Coverage
Inhibit
●
Touch Coverage Inhibit.
DO NOT DISTURB
If you don’t want to be interrupted as you work, use the Do Not
Disturb feature to prevent calls from ringing at your voice ter-
minal. Program this feature on a button with lights.
To program:
●
●
T/P to P
T/P to center
●
Touch the button Dial *71
●
To prevent calls from ringing at your voice terminal:
●
Touch Do Not Disturb.
Do Not Disturb
The green light next to the button goes on.
36
When the Do Not Disturb feature is active, the green light next
to your line button flashes when you receive outside calls, but
your voice terminal does not ring. Calls transferred to you return
to the sender after a prescribed number of rings (set by your
system administrator), and intercom calls to you get a busy
signal.
●
Do Not Disturb
Touch Do Not Disturb again.
The green light next to the button goes out.
NOTE: If you have a Cover button for one or more people (see
“Call Coverage,” page 34), their voice terminals ring when you
call them on the intercom from your voice terminal even if they
are using the Do Not Disturb feature.
PRIVACY
If you share an outside line with other people connected to your
MERLIN system, you can use the Privacy feature to prevent
others from accidentally joining your telephone conversations.
Program this feature on a button with lights.
●
●
T/P to P
T/P to center
●
Touch the button Dial *72
●
To program:
To prevent others from joining your calls:
●
Before placing or receiving a private call, touch Privacy.
Privacy
The green light next to the button goes on.
37
The feature remains active until you:
●
Touch Privacy again.
Privacy
The green light next to the button goes off.
TOUCH-TONE ENABLE
(Only for systems with rotary lines)
If you have telephone lines that carry rotary signals, you can use
the Touch-Tone Enable feature to switch to Touch-Tone signals
midway through a dialing sequence. This lets you take advan-
tage of bank-by-phone, credit card authorization, and alternate
long distance services.
●
●
T/P to P
T/P to center
●
Touch the button Dial *76
●
To program:
To switch from rotary pulse to Touch-Tone signals as you dial a
number:
●
Lift your handset.
●
Dial the first part of the number.
Touch Touch-Tone Enable.
Touch-Tone
Enable
+
+
+
●
●
Dial the remaining numbers.
The Touch-Tone Enable feature turns off when you hang up your
handset or touch Recall.
38
ACCOUNT NUMBER ENTRY
(For use only with the SMDR feature)
With an Account Number button, you can enter an account
number that identifies who should be billed for the call. Program
this feature on a button with lights.
To program:
●
●
T/P to P
T/P to center
●
Touch a button Dial *82
●
To enter an account code:
●
Touch Account Number while you have a call in progress.
The green light next to the button flashes.
Dial the account code.
Account Number
Account Number
+
+
●
●
account
code
Touch Account Number again.
If the account code is entered properly, the green light next to the
button stops flashing and stays on.
If you enter the account code incorrectly, keep the call in pro-
gress and simply repeat the above procedure.
CALL PARK
Use the Call Park feature to put a call on hold for someone to
pick up from any voice terminal in your MERLIN system. You
can use the instructions below to program a Call Park button
on your voice terminal. Or, you can save a feature button for
another use, and dial a code to park a call.
If you have a loudspeaker paging system, you can use it to an-
nounce the call.
39
If no one answers a parked call, your voice terminal rings to re-
mind you the call is still parked.
●
●
T/P to P
●
Touch a button Dial *86
●
To program:
T/P to center
To park a call using a Call Park button:
Call Park
●
Touch Call Park.
+
●
Hang up.
Using a Dial Code
To park a call using a dial code:
Transfer
●
Touch Transfer.
+
+
The green light next to the line’s button flashes.
Dial your own intercom number.
Hang up.
your
intercom
number
●
●
CALL PICKUP
Use the Call Pickup feature to answer a call that is ringing,
parked, or on hold at another MERLIN system voice terminal.
You can use the instructions below to program a button for Call
Pickup, or, if you want to save a feature button for another use,
you can use a dial code to pick up a call.
●
●
T/P to P
T/P to center
●
Touch a button Dial *85
●
To program:
40
To pick up a call using a Call Pickup button:
+
+
Call Pickup
●
Touch Call Pickup.
intercom
number
●
Lift your handset.
●
Dial the intercom number of the voice terminal holding the
call.
Using a Dial Code
To pick up a call using a dial code:
●
Touch Intercom-Ring or Intercom-Voice.
●
Lift your handset.
●
Intercom
Ring
Dial *7.
+
+
●
Dial the intercom number of the voice terminal holding the
call.
LINE PICKUP
+
Use this feature to pick up a specific line that is parked, on hold,
or ringing at another voice terminal. This feature offers three
options:
* 7
intercom
number
●
Program one Line Pickup button and use it with 2-digit line
codes to pick up lines.
●
Program individual buttons to pick up specific lines.
●
Use a dial code and a 2-digit line code to pick up a line.
If you do not have a list of 2-digit line codes for your outside lines,
ask your system administrator for one.
41
Using a Single Line Pickup Button
T/P to P Touch the button Dial
●
●
●
To program:
*84 T/P to center.
●
To pick up a line using this option:
●
Touch Line Pickup.
Line Pickup
+
+
●
Lift your handset.
line
code
●
Dial the 2-digit line code for the line you want to pick up.
Using Buttons Programmed to Pick Up Specific Lines
●
T/P to P
*84 + the 2-digit line code for the line
T/P to center
●
Touch the button
●
Dial
To program:
●
To pick up a line using this option:
●
Touch the button for the line you want to pick up.
●
Lift your handset.
Pickup
+
555-1234
Using a Dial Code
To pick up a line using a dial code:
●
Touch Intercom-Ring or Intercom-Voice
●
Lift your handset.
Intercom
Ring
●
Dial *8.
+
+
+
●
Dial the 2-digit line code for the line you want to pick up.
*8
line
code
42
Ringing and Line Selection Options
RINGING OPTIONS
Programmable Line Ringing
You can determine whether calls coming in through a line pool,
your individual line, or a line you’re covering ring immediately,
ring after a delay, or do not ring at all.
NOTE: This does not affect intercom calls or calls transferred
to you.
If you share lines with someone, use this feature to cover out-
side calls for one another. For example, if you want your
coworker’s calls always to ring first at your voice terminal, pro-
gram your lines to ring immediately and your coworker’s to ring
after a delay or not at all. Or, if you want to cover that person’s
outside calls only when he or she is out of the office, program
your lines to ring after a delay and your coworker’s lines to ring
immediately.
If your voice terminal has Pool Access buttons, calls coming in
on the pooled lines do not ring at your voice terminal unless you
change the setting for your Pool Access buttons.
43
To program line ringing:
●
Slide the T/P switch to the P position.
●
Touch the line button successively until the red light in-
dicates the type of ringing you want.
555-1234
+
+
Red light on
immediate ring
delayed ring
no ring
=
=
=
Red light flashing
Red light off
●
Slide the T/P switch to the center position.
If your lines are not pooled, the green light flashes next to the
line button when a call comes in for you, even if you program
the line not to ring. If you want to answer the call:
●
Touch the button next to the flashing green light.
555-1234
+
●
Lift your handset.
Personalized Ringing
If your voice terminal’s ringing is easily confused with the ring-
ing of other nearby voice terminals, you can choose another
ringing pattern from eight different ringing options.
To program Personalized Ringing:
●
Slide the T/P switch to the P position.
You hear the ringing sound that your voice terminal makes when
you receive an outside call.
●
Touch Speaker.
The ringing sound changes.
44
●
●
Touch Speaker repeatedly until you hear a ringing sound
you like.
Slide the T/P switch to the center position.
Speaker
Speaker
+
+
+
Voice Announcement Disable
Ordinarily, people can announce calls through your voice ter-
minal speaker. However, you can prevent voice announcements
and have all intercom calls ring instead.
To program Voice Announcement Disable:
●
Slide the T/P switch to the P position.
●
Touch Intercom-Voice.
=
=
Green light on
Green light off
voice signal allowed
voice signal prevented
Intercom
Voice
+
+
●
Slide the T/P switch to the center position.
AUTOMATIC LINE SELECTION
This feature controls the order in which the system selects out-
side lines when you lift your handset to place a call. You can,
for instance, program the line you use most often to be the first
line in the Automatic Line Selection sequence, and a line you
use less often to be the next line the system selects. Then, when
you lift your handset, the system automatically selects the line
you usually use, if that line is not busy. If it is busy, the system
automatically selects your second choice, unless that line is
busy, and so on.
You can specify up to eight of your outside lines (both individual
and pooled) and intercom lines for Automatic Line Selection.
45
NOTE: If you plan to program other features when you program
Automatic Line Selection, you must program Automatic Line
Selection first. If you are already in the middle of a programming
session, slide the T/P switch to center and then back to P before
programming this feature.
●
Slide the T/P switch to the P position.
●
Dial **.
555-1234
+
+
+
●
Touch the line buttons in the order you prefer.
●
Slide the T/P switch to the center position.
**
NOTE: If you dial ** and then do not touch a line button, Pool
Access button, or Intercom button, you cancel Automatic Line
Selection.
46
Simultaneous Voice and Data Calls
If you have a General Purpose Adapter and a modem connected
to your voice terminal, you can use the Simultaneous Voice and
Data Calls feature. You may be speaking with someone on the
telephone and wish to obtain some data from a computer to sup-
port your conversation. Or you may want to make a voice call
while you are sending data to someone outside your business.
With Simultaneous Voice and Data Calls, you can make voice
calls and data calls at the same time.
NOTE: You cannot use your Hands-Free Unit when the
Simultaneous Voice and Data Calls feature is active.
To enter simultaneous voice and data mode:
●
Slide the T/P switch to the P position.
●
Touch Message.
Message
+
+
The green light next to the button goes on.
●
Slide the T/P switch to the center position.
The green light next to the button goes off unless you have a
message waiting.
To make a data call:
●
Touch Speaker.
Speaker
●
+
Dial the outside telephone number or intercom number for
your host computer.
outside
number
47
●
When the computer returns the carrier signal, turn on your
modem.
The green light next to the line or Intercom button you used to call
the computer begins to flash and continues to flash until you end
the data call.
●
Log on from your terminal keyboard.
To end a data call:
●
Log off from your terminal keyboard.
●
Turn off your modem.
The green light next to the line or Intercom button you used to make
your data call goes off.
You can keep your voice terminal in simultaneous voice and data
mode indefinitely. If you want to leave this mode, however, follow
these steps:
●
Slide the T/P switch to theP position.
The green light next to Message goes on.
Message
●
Touch Message.
+
+
The green light next to the button goes off.
●
Slide the T/P switch to the center position.
48
Using PBX, Centrex, or Custom Calling Features
If you have PBX, Centrex, or Custom Calling features, use them
exactly as their instructions describe with one important excep-
tion: Any non-
MERLIN system feature code that begins with
a “#” must be preceded by another “#”. For example, if PBX,
Centrex, or Custom Calling instructions tell you to dial
#1234
you must dial
##1234
to use the feature with your MERLIN system.
Similarly, when you program a PBX, Centrex, or Custom Call-
ing feature code beginning with “#” for Outside Auto Dial or
Speed Dial, you must enter “##” before you enter the rest of
the feature code.
49
Optional Equipment
HANDS-FREE UNIT
The Hands-Free Unit is a high-quality speakerphone that allows
you to use your voice terminal without lifting your handset.
NOTE: Any custom feature that ordinarily activates your voice
terminal’s speaker activates your Hands-Free Unit.
Placing Calls
To place outside calls using your Hands-Free Unit:
●
Touch Speakerphone On/Off on the Hands-Free Unit.
●
Dial a number, or touch an Outside Auto Dial button.
● When you hear the other person answer the phone, begin
talking.
●
To end the call, touch Speakerphone On/Off.
To place intercom calls using your Hands-Free Unit:
●
Touch Intercom-Ring or Intercom-Voice.
●
Touch Speakerphone On/Off on the Hands-Free Unit.
●
Dial an intercom number.
●
Speak when you hear the other person answer (ringing in-
tercom calls), or when you hear a beep (announced inter-
com calls).
●
To end the call, touch Speakerphone On/Off.
50
Answering Calls
To answer a call with your Hands-Free Unit:
●
Touch Speakerphone On/Off and begin speaking.
To temporarily remove yourself from a conversation to consult
with someone else in your room:
●
Touch Microphone On/Off.
The green light next to the button goes off.
●
To participate in the conversation again, touch Microphone
On/Off again.
The green light next to the button goes on.
If you lift your handset during a call, you turn off the Hands-Free
Unit. To turn it on again:
●
Touch Speakerphone On/Off.
●
Hang up your handset.
GENERAL PURPOSE ADAPTER
The General Purpose Adapter enables you to place and receive
calls through a cordless telephone, a facsimile machine, or data
transmission equipment. It also allows you to place calls with
a Touch-Tone autodialer and to receive calls with an answering
machine.
To learn how to use the adapter with your equipment, refer to
the instructions that come with the adapter.
51
Index
Personalized Ringing, 44 - 45
Placing Calls, 4 - 8, 50
Intercom, 7 - 8, 50
Outside, 4 - 6, 50
Privacy, 37 - 38, 55
Programmable Line Ringing, 43 - 44
Delayed Ring, 43 - 44
Immediate Ring, 43 - 44
No Ring, 43 - 44
Hands-Free Unit, 14, 47, 50 - 51
Hold, 10
SMDR, 39
Answering Calls, 9, 51
Answering Machine, 51
And General Purpose Adapter, 51
Assigning Custom Features to Buttons, 16
Auto Answer-All, 33, 54
Auto Intercom, 21 - 22, 54
32 - 33
Intercom Calls, 7 - 8, 50
Announced, 8, 50
Ringing, 7 - 8, 50
Last Number Redial, 25, 53
Line Pickup, 41 - 42
Line Pools, 5 - 6
Recall, 2, 15
Ringing Options, 43 - 45
Button Access,
5
Call Coverage, 34 - 35, 43, 55
Call Forwarding, 36
Call Park, 39 - 40, 55
Call Pickup, 40 - 41, 55
Conference Calls, 2, 11 - 12
Drop, 12
Hold, 10
Rejoining, 12
Coverage Inhibit, 35 - 36, 55
Programming Instructions, 16
SMDR, 39
Speaker, 2, 13 - 14
Special Characters, 20 - 21
Pause, 20
Message, 14, 47 - 48, 55
Modem, 47 - 48
Notify, 17 - 19, 56
32 - 33
On-Hook Dialing, 2, 13
Optional Equipment, 50 - 51
Outside Auto Dial, 19 - 21, 53
Outside Calls, 4 - 7, 50
Stop, 20
Touch-Tone Enable, 20
System Speed Dial, 23, 53
Data Calls, 47 - 48
Do Not Disturb, 36 - 37, 55
Drop, 2, 12
Touch-Tone Enable, 20, 38
T/P Switch, 2, 16
Transfer, 2, 10 - 11, 32
Paging, 26 - 29, 54
Feature Programming Chart, 53 - 56
Fixed Features, 10 - 15
One-Touch Transfer, 32
Transfer with Voice Announcement, 11
Group Page, 28 - 29, 54
Loudspeaker Page, 26 - 27, 54
Personal Speed Dial, 22, 53
Group Page, 28 - 29, 54
Group Call Distribution, 30 - 31
Voice Announcement Disable, 45
Volume Control,
2
52
Feature Programming Chart
Use the chart below as a quick reference when you want to program features onto your voice terminal.
Feature Name
(Suggested Button Label)
Programming Code
Notes
QUICK DIALING FEATURES
Dial *90 + an outside number, an account
number, or a PBX, Centrex, or Custom Calling
feature code.
Outside Auto Dial
(name or location)
See page 19.
A button with lights is recommended but not re-
quired. See page 21.
Auto Intercom
(name or location)
Dial *91 + a MERLIN system intercom
number.
Dial a Personal Speed Dial code (#01 through
#22) + *90 + an outside telephone number,
an account number, or a PBX, Centrex, or
Custom Calling feature code.
This feature does not use a button. For 5- and
10-button voice terminals only. See page 22.
Personal Speed Dial
(does not use a button)
Dial *95 + a System Speed Dial code (60
through 99).
System Speed Dial
(name or location)
See page 23.
Dial *74.
can dial a code to use this feature. See page 23.
Saved Number Redial
(Saved Number)
Dial *73.
If you have a 5- or 10-button voice terminal, you
can dial a code to use this feature. See page 25.
Last Number Redial
(Last Number)
Dial *6 + the intercom number for the person
you want to signal.
Manual Signaling
(Signal “name”)
See page 25.
53
Feature Programming Chart (continued)
Feature Name
(Suggested Button Label)
Programming Code
Notes
PAGING FEATURES
Dial *91 + one of the following codes:
80 for all zones
Loudspeaker Page
(Page “number or name”)
See page 26.
zone 1
zone 2
zone 3
81
82
83
Dial *91 + one of the following codes:
841 for group 1
See page 28.
Group Page
(Grp. Page “number or
name”)
842 group 2
group 3
844 group 4
843
group 5
group 6
847 group 7
845
846
AUTO ANSWER FEATURES
Requires a General Purpose Adapter and a but-
ton with lights. Used only with a modem or an
answering machine. See page 33.
Dial *75.
Dial *70.
Auto Answer-All
(Auto Answer-All)
Requires a Hands-Free Unit and a button with
lights. See page 34.
Auto Answer-Intercom
(Auto Answer-Intercom)
54
Feature Programming Chart (continued)
Feature Name
(Suggested Button Label)
Programming Code
Notes
CALL COVERAGE FEATURES
Dial *4 + the intercom number of the person
you want to cover.
Requires a button with lights. See page 34.
Requires a button with lights. See page 35.
Call Coverage
(Cover “name”)
Dial *77.
Coverage Inhibit
(Coverage Inhibit)
OTHER FEATURES
Privacy
(Privacy)
Dial *72.
Dial *71.
Dial *76.
Dial *82.
Dial *86.
Dial *85.
Do Not Disturb
(Do Not Disturb)
Touch-Tone Enable
(Touch-Tone Enable)
Account Number Entry
(Account Number)
Call Park
(Call Park)
See page 40.
Call Pickup
(Call Pickup)
Dial *84 (or dial *84 + a line code to program
buttons to pick up specific lines).
Line Pickup
(Line Pickup)
See page 41.
Dial *98.
Requires a button with lights. For 5-button voice
terminals only. See page 14.
Message
(Message)
55
Feature Programming Chart (continued)
Feature Name
(Suggested Button Label)
Notes
Programming Code
OTHER FEATURES (continued)
Notify
Notify Send
(Send to “name”)
Dial *87 + the intercom number of the person
you want to notify.
Dial *88 + the intercom number of the person
notifying you.
Requires a button with lights. See page 18.
See page 30.
Notify Receive
(Receive from “name”)
Dial *91 + one of the following codes:
850 for group 1
Group Call Distribution
(Grp. Call “number or
name”)
group 2
group 3
group 4
group 5
group 6
851
852
853
854
855
56
®
MERLIN Communications System
Models 1030 and 3070 with Feature Module 5
Quick Reference Card
FIXED FEATURES
HOW TO USE
FEATURES
INTERCOM CALLS
Intercom-Ring Calls
1. Touch Intercom-Ring. 2. Lift handset. 3. Dial
2-digit intercom number.
1. Touch Intercom-Voice. 2. Lift handset. 3. Dial
2-digit number. 4. When you hear a beep, talk into
your handset.
Intercom-Voice Calls
OUTSIDE CALLS
1. Touch line button you want if red light next to it is
not lit. 2. Lift handset. 3. Dial number.
Outside Calls (Regular)
1. Touch Pool Access button you want if red light
next to it is not lit. 2. Lift handset. 3. Dial outside
number.
Outside Calls (with ARS)
1. Touch Pool Access button you want if red light
next to it is not lit. 2. Lift handset. 3. When you
hear a dial tone, dial the code for the line pool you
want. 4. When you hear another dial tone, dial the
outside telephone number.
Outside Calls with Dial
Access to Line Pools
1. Touch the pool button you want if red light next to
it is not lit. 2. Lift handset. 3. Dial number.
Outside Calls with Button
Access to Line Pools
CALLS ON HOLD
Put Call On Hold
Take Call Off Hold
TRANSFER CALLS
Transfer Calls
Touch Hold.
Touch the held call’s button.
1. Touch Transfer. 2. Dial appropriate intercom
number. 3. Hang up.
1. Touch Transfer. 2. Touch Intercom-Voice. 3. Dial
appropriate intercom number. 4. Announce call
through handset. 5. Hang up.
Transfer Calls with Voice
Announcement
CONFERENCE CALLS
1. Touch Conference. 2. Touch line button (or
Intercom-Ring or Intercom-Voice). 3. Dial outside
number (or intercom number). 4. When the person
answers, announce the conference call. 5. Repeat
this procedure for each person you want to include
in the conference.
Connect Conference Calls
1. Touch Drop. 2. Touch the button of the line you
want to disconnect.
Disconnect Conference
Calls
PROGRAMMABLE FEATURES
HOW TO PROGRAM
Slide T/P to P Touch button
FEATURES
●
●
●
Dial this code:
QUICK DIALING
Outside Auto Dial
*90 + outside number, account number, or a
PBX/Centrex feature code
*91 + MERLIN system intercom number
Auto Intercom
Personal Speed Dial
A Personal Speed Dial code (#01—#22) + *90 +
outside number (does not use a button)
*95 + System Speed Dial code (without #)
*74
System Speed Dial
Saved Number Redial
Last Number Redial
*73
*6 + the intercom number
Manual Signaling
PAGING
*91 + appropriate code (uses additional
equipment)
Loudspeaker Page
*91 + appropriate code
Group Page
AUTO ANSWER
Auto Answer-All
Auto Answer-Intercom
CALL COVERAGE
Call Coverage
*75 (uses additional equipment)
*70 (uses additional equipment)
*4 + intercom number of the person you want to
cover (use a button with lights)
*77 (use a button with lights)
Coverage Inhibit
OTHER
*72 (use a button with lights)
Privacy
*71 (use a button with lights)
*76
Do Not Disturb
Touch-Tone Enable
Account Number Entry
Call Park
*82 (use a button with lights)
*86
*85
Call Pickup
*84 (or *84 + line code to program buttons to
pick up specific lines)
Line Pickup
*98 (use a button with lights)
Message
No dial code is necessary. Just slide T/P to P and
touch Message (light goes on).
Simultaneous Voice and
Data Calls
*87 + intercom number of the person you want to
notify (use a button with lights)
Notify Send
*88 + intercom number of the person notifying
you (use a button with lights)
Notify Receive
*91 + appropriate code
Group Call Distribution
AT&T
MERLIN is a registered trademark of AT&T
© Copyright 1986 AT&T. Printed in U.S.A.
999-500-143 IS
May 1986
Issue 1
|