2
User's Manual for
Two-Line Digital
Answering System Telephone
with Speakerphone 1872
Fold open this paper for information about this
telephone's installation and operation. Please
read Part 1 — Important Product Information,
included in this package.
Part 2
© Copyright 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in Mexico. Issue 1AT&T
848229506
I N S T A L L A T I O N
Place line cord in channel.
Set the Dial Mode switch.
Connect the line
cord, as described
in instructions.
Reverse the handset tab.
4 Connect the line cord(s) to the
modular jack(s), and mount the phone
on the wall.
WALL MOUNTING INSTALLATION
SETTING THE CLOCK
1 Connect line cord(s) to the telephone.
See Step 1 in Table/Desk Installation.
Two-line jack — Use the 8-inch line
cord, and plug into the jack labeled
L1 OR L1/L2 on the bottom of the
phone.
The clock records the day and time each
message is received.
Two-line jack — Plug the free end of
the 8-inch cord into the wall jack.
Two separate jacks — Plug the free end
of the 8-inch cord into the jack where
the phone is to be mounted, and plug the
free end of the 7-foot cord into the other
jack.
1 Press C. You hear a day.
2 Press a number button (1 to 7) to choose
the current day (Sunday - Saturday).
3 Press C. You hear a time.
4 Use the number buttons to enter the
correct time.
5 Press * for AM or # for PM.
6 Press C. If you have entered a valid
time, you hear the new day and time. If
you hear five rapid beeps, repeat Steps
1-6.
Two separate jacks — Use the 8-inch
line cord, and the 7-foot line cord with
blue plugs.
Place the phone on the wall jack
mounting studs and pull down until it
is held securely.
2 Attach the base.
See Step 2 in Table/Desk Installation.
3 Reverse the handset tab.
5 Connect the handset to the telephone.
Plug the coiled cord into the handset jack
on the side of the phone. Plug the other
end into the handset and hang up.
SELECTABLE DIAL INFORMATION
This telephone has a push button dial
which will work with tone or dial pulse
(rotary) service. Even when set to dial
pulse service, the phone can be switched
temporarily to tone, for access to some
tone-activated computer systems.
Hold down the switchhook and slide the
tab up and out of its slot. Turn the tab
so the curved end is up, and insert it back
in the slot.
6 Follow Steps 5-8 in Table/Desk
Installation.
I N C A S E O F D I F F I C U L T Y
If you have difficulty operating this phone,
try the suggestions below. If you still have
trouble, call 1 800-722-9125.
flashing line might be set to Announce
Only, and no announcement is recorded for
that line. If you recorded an announce-
ment for AO, it might have been lost in a
power failure. Try recording a new an-
nouncement for AO, or switch to a differ-
ent announcement. See “Recording an
Announcement.”
commands, make sure you are responding
to the prompts in a clear, audible voice.
MESSAGES ARE INCOMPLETE
The system can accept messages up
NO DIAL TONE
Make sure all plugs are connected
❥
❥
to 4 minutes long. If a caller leaves a very
long message, part of it might be lost when
the system disconnects the call after 4
minutes.
properly. Inspect the line cord connections
at the modular jack and at the telephone.
Also inspect the coiled handset cord con-
nection at both ends.
SYSTEM DOES NOT DISCONNECT
WHEN YOU ANSWER FROM
❥
If the caller pauses for more than 7
❥
Unplug the telephone and connect it
seconds, the system stops recording and
disconnects the call.
to another modular jack.
ANOTHER TELEPHONE
❥
If the system’s memory fills up
The answering system will not always dis-
connect if you answer the call from another
phone at the same time that the system
answers. To stop the answering system,
press S, or quickly press and release
the switchhook on the phone you are using.
CALL CANNOT BE DIALED,
OR IS DIALED SLOWLY
See “Setting Up the System” in Installa-
tion to set the Dial Mode switch. If you
have pulse dialing service you cannot dial
numbers with the switch set to TT (touch
tone). Set the switch to DP (dial pulse),
then hang up and dial again.
during a message, the system stops
recording and disconnects the call.
LINE DOES NOT ANSWER AFTER
CORRECT NUMBER OF RINGS
❥
Make sure the ON/OFF light for that
line is on. See “Setting the System to
Answer Calls.”
TIME AND DAY FLASH
IN MESSAGE WINDOW
If the clock stops running because of a
power failure, the time and day flash in the
Message Window to indicate that the clock
should be reset. See “Setting the Clock.”
❥
If the Toll Saver feature is on, the num-
PROBLEMS WITH MESSAGE WINDOW
ber of rings changes from 4 to 2 or from 6
to 4 if a new message has been recorded in
any of the mailboxes. See “Toll Saver.”
OR INDICATOR LIGHTS
Make sure all plugs are connected
properly. Inspect the line cord connections
at the modular jack and at the telephone.
Make sure the power cord is securely
plugged into an electrical outlet not
controlled by a wall switch.
OTHER PROBLEMS
Make sure you have followed all the
instructions in this manual. If you cannot
correct the problem, press the reset but-
ton.
SYSTEM DOES NOT RESPOND TO
REMOTE COMMANDS
❥
If power failed when the backup
batteries were missing, or battery power
was low, the Remote Access Code might
have returned to its factory setting. See
“Remote Access Code.”
TELEPHONE DOES NOT RING
Make sure the Ringer Volume switch
1 Remove the directory card and its cover.
You will see the reset button.
2 The button is recessed. Use the end of a
paper clip to press the reset button.
❥
for the silent line is set to LO or HI.
If there are several other telephones
❥
If you are using dial buttons to enter
❥
remote commands, make sure you are call-
ing from a touch tone phone. When you
dial a number, you should hear tones; if
you hear clicks instead, the phone is not
using touch tone service.
on the same line, try disconnecting some
of the other telephones. Having too many
telephones connected can also create
problems such as low ringer volume, or
impaired sound quality during calls.
If there is a problem with the system, press-
ing the reset button will reset the system,
and might delete any messages as well as
your announcements. Follow the instruc-
tions in this manual to record a new an-
nouncement.
❥
Some telephones transmit only one
brief tone each time you press a number.
If you are using one of these telephones,
the answering system might not detect the
Remote Access Code while the announce-
ment is playing. Wait until the announce-
ment is over and enter the code again.
LOW BATTERY LIGHT IS ON
Make sure the batteries are installed
If there is no problem with the system,
pressing the reset button will have no
effect.
❥
correctly.
❥
If the light remains on, replace all 4
batteries with new batteries.
❥
There might be noise interference on
L1 or L2 ON/OFF LIGHT
the phone line you are using. Press firmly
on the number buttons.
FLASHES RAPIDLY
If both lights are flashing, then memory
may be full. See “When Memory is Full.”
If one or the other light is flashing, the
❥
Make sure you are entering the
Remote Access Code correctly.
If you are using voice-activated
❥
A N S W E R I N G S Y S T E M O P E R A T I O N
A w a y F r o m H o m e
You can use many answering system
features when you are away from home.
To protect your privacy, most features can
only be used after you enter a 3-digit
Remote Access Code. Enter commands
using the keys on any touch tone phone,
or by using Voice Activated Commands.
2 Press 00 to turn on both lines, or 01
toturn on only Line 1, or 02 to turn on
only Line 2.
FORWARD
To skip an entire message, press 5 while
that message is playing.
To skip part of a message, hold down 5.
Release 5 to resume playing.
NOTE: If you press 0 and hear five rapid
beeps, then either memory is full or
Announcement AO is selected and no
announcement is recorded.
STOP
Press # to stop message playback.
CONNECT WITH
THE ANSWERING SYSTEM
1 Dial your telephone number.
2 While the system is playing your
announcement, enter your Remote
Access Code. The system announces the
number of messages in each mailbox,
and beeps twice to indicate it is ready to
accept a command.
CHANGING THE
REMOTE ACCESS CODE REMOTELY
1 Access the system using the current
Remote Access Code.
2 After the two-beep signal, press 99.
You hear “Enter new code”
3 Enter your new Remote Access Code.
4 If a valid code is entered, the system
announces the new RemoteAccess Code
and beeps twice.
5 If an invalid code is entered, you hear
five rapid beeps followed by two beeps.
Repeat steps 2 and 3.
RECORDING A MEMO
After listening to your messages, you can
record a memo to be played back later.
1 Press the number of a line or mailbox
(1-4) and then *.
2 Begin speaking after the beep.
3 Press # when you are done.
CHANGING ANNOUNCEMENTS
You can re-record any of the announce-
ments currently in use by any
line or mailbox.
1 Contact the answering system.
2 After two beeps press a number key
(1-4) to select a line or mailbox, then
press 4*. The system beeps and begins
recording.
3 Speak into the telephone in a normal tone
of voice.
4 Press # when you are finished. The
system beeps once and plays the new
announcement.
To review your announcement, press a
number key (1-4) to select a line or mail-
box. Press 41 after the two beeps to play
your announcement.
PLAYING YOUR MESSAGES
After the two beep signal you can:
• Wait four seconds or press 7 to play
all of your messages.
• Press 6 to play only new messages.
• Press the number of a line or mailbox
(1-4) and then 7 to play all of the
messages from that line or mailbox.
• Press the number of a line or mailbox
(1-4) and then 6 to play only new
messages from that line or mailbox.
VOICE HELP MENU
This feature allows you to use the system
from a remote location when you cannot
remember the touch-tone commands. You
need only to remember your Remote
Access Code and the system will prompt
you for commands. After listening to your
messages you hear “End of messages.” The
system then lists several command
prompts. When you hear the command you
want to use, press the corresponding buttons.
SAVE MESSAGES
The system automatically saves messages
after playback.
DELETE MESSAGES
To delete only selected messages, press
3 while that message is playing.
To delete all messages for all lines and
mailboxes, press 0 3 . You’ll hear
“Messages deleted.”
To delete all messages for a particular
line or mailbox, press the number of the
line or mailbox (1-4) and then press 3.
You’ll hear “Messages deleted.”
MEMORY FULL/NO ANNOUNCEMENT
NOTE: If announcement is being used by
both lines, re-recording the announcement
will change the announcement heard on
both lines.
If the system is off, memory is full, or your
AO message is lost due to a power or
battery failure, the system will answer
after ten rings and present two beeps
instead of your announcement.
TURNING THE SYSTEM OFF
After the two beep signal:
• Press 188 to turn off Line 1.
• Press 288 to turn off Line 2.
• Press 88 to turn off both lines.
To set your system to record messages
and answer calls:
1 Enter your RemoteAccess Code after the
two-beep signal.
2 Listen to any messages and delete some
or all of them.
3 Press 141 or 241 to review the
Line 1 or Line 2 announcement. If there
is no announcement, press 14* to
record an announcement on Line 1 or
24* to record on Line 2.
NOTE: If you try to delete a group of
messages that includes new messages, the
system beeps five times and doesn’t delete
any messages.
TURNING THE SYSTEM ON
If you forgot to turn on the system before
leaving home, you can do so from a
touch-tone phone using your Remote
Access Code.
REPEAT
To repeat an entire message, press 2
while that message is playing.
4 Press 00 to make sure the system is on
before you hang up.
1 Dial your phone number and wait for ten
rings. The system answers and beeps
twice. (No announcement will play.)
To repeat part of a message, hold down
2. To resume playing, release 2.
A N S W E R I N G S Y S T E M O P E R A T I O N
A w a y F r o m H o m e
3 You then hear, "First digit," followed by
"Enter 4," "Enter 5," "Enter six," and so
forth. When you hear the first digit of
the Remote Access Code, immediately
respond by saying "Enter code."
8 After the last message plays, the system
announces "End of messages" followed
by the prompt "Replay messages?"
Voice Activated Commands
When a touch tone telephone is not avail-
able, you can still call the system to listen
to your messages. Use your voice to enter
the Remote Access Code, to repeat the
messages, and to delete messages.
To replay all the messages, say "Replay
messages." If you remain silent, the
system prompts "Delete all messages?"
9 To delete all the messages you just heard,
say "Delete messages." The system then
repeats the "Delete all messages?"
prompt to confirm your choice. To
confirm the delete, say "Delete
messages." The system announces
"Messages deleted." If you remain silent
after the "Delete all messages?" prompt,
the messages are not deleted.
For example, if your Remote Access
Code is 543, wait to hear "Enter five,"
then say "Enter code."
4 You then hear "Second digit," followed
by "Enter zero," "Enter one," Enter two,"
and so forth. When you hear the second
digit of the Remote Access Code, say
"Enter code."
5 You then hear "Third digit," followed by
"Enter zero," "Enter one," Enter two,"
and so forth. When you hear the third
digit of the Remote Access Code, say
"Enter code."
6 If you enter the code correctly, the
system announces how many messages
have been received for each mailbox,
and begins to play all the messages.
Speak in response to the prompts presented
by the system as described below. You
must speak quickly and loudly in order for
the system to detect your voice.
The system does not recognize the actual
words you are saying; it responds to any
sufficiently intense auditory signal. For
example, you could say any phrase that is
easy for you to remember, instead of say-
ing "Enter Code."
If you do not enter
the correct Remote Access Code.
If you enter an incorrect Remote Access
Code, the system beeps five times and be-
gins the sequence of prompts again. If you
enter the wrong code on the second try, the
system disconnects the call.
You can hang up at any time during the
call. The system saves your messages,
unless you respond to the "Delete all mes-
sages?" prompt.
If no messages have been received, the
system disconnects the call.
1 Dial your telephone number, listen for
the announcement, and then remain
silent after the beep.
If you do not respond to the correct digit
while entering the RemoteAccess Code (or
if the system fails to detect your response),
you can remain silent until after you hear
the "Enter nine" prompt. The system beeps
five times and begins the sequence of
prompts again. If you do not respond cor-
rectly during the second sequence of
prompts, the system disconnects the call.
7 At the end of each messages, the system
prompts "Repeat message?" To hear the
message again, say "Repeat message."
If you remain silent, the system plays
the next message. You can repeat each
message once.
If the system answers after 10 rings
(because it is off or the memory is full),
remain silent after the two-beep signal.
2 After about 10 seconds, the system
prompts "Enter remote access code."
Immediately respond by saying "Enter
code."
T E L E P H O N E O P E R A T I O N
MAKE OR ANSWER A CALL
AUTO REDIAL
MUTE
1 Lift the handset
If you place a call and hear a busy signal,
hang up, and then press (. The
system redials the number you just called.
To mute a call, press M. You can hear
the other party, but the other party cannot
hear you.
— OR —
Press K
2 Press L or l.
When you hear the line ringing, lift the
handset or press K to talk. If you don’t
do so within 60 seconds, the system hangs
up. If the system detects a busy signal, it
will hang up, wait 40 seconds, and try again
(up to 10 times).
Press M again to continue 2-way
conversation.
ENDING A CALL
Place the handset in the cradle
— OR —
NOTE: Mute is canceled if you switch
between speakerphone and handset, or if
you put the call on Hold.
Press K (if on a speakerphone call).
SWITCHING BETWEEN HANDSET AND
SPEAKERPHONE
To switch from handset to speakerphone
during a call, press K.
To switch from speakerphone to handset
during a call, lift the handset.
To cancel automatic redialing, press
( or lift the handset or press K.
FLASH
Use h instead of pressing the
switchhook to activate services such as
Call Waiting or Three-Way Calling.
HOLD
Press H. You can now replace the hand-
set in the cradle without disconnecting the
call. The speakerphone is automatically
turned off.
AUTOMATIC LINE SELECTION
The system is preset to select a line for you
in most cases when you lift the handset or
press K.
To change how the system selects a line,
see “Line Selection Options” later in this
manual.
TEMPORARY TONE
To take a line off hold, press the
appropriate line button or lift the handset
of an extension phone on that line.
If you have rotary service, you can change
from pulse to tone dialing during a call by
pressing T. This is useful if you need
to send tone signals for access to telephone
banking or long-distance services.
1 Dial a number.
The hold feature allows you to switch
between calls on both lines without dis-
connecting either call.
2 Press T. Buttons pressed after this
will send tone signals.
3 After you hang up, the phone
automatically returns to rotary service.
LINE STATUS
CONFERENCE CALLS
1 Make or answer a call, then press c.
2 Establish a call on the other line, then
press c.
Line 1 and Line 2 lights indicate when a
line is in use. A flashing red light
indicates the line is on hold. A flashing
green light indicates the line is ringing.
To end a conference call, hang up both
lines. All parties will be disconnected.
Each line has its own ringer tone to signal
an incoming call. If you are on a call when
the other line starts to ring, you will hear
only one short ring, so you can continue
your call without further interruption.
If one caller hangs up during a conference
call, you might hear a dial tone. Press the
line button of the remaining call to
eliminate the dial tone.
REDIAL
The last number dialed on this phone is
stored in redial memory until you dial an-
other number.
CONFERENCE CALL OPTIONS
To place a conference call on hold:
1 Press H to hold both lines.
2 Press c to continue your conference
call.
1 Lift the handset
— OR —
press K
— OR —
press L or l.
The number stored in redial memory is
displayed.
To talk privately with one caller:
1 Press H.
2 Press the line button of the person with
whom you want to speak privately.
3 Press c to continue your conference
call.
2 Press (.
To disconnect only one party from a
conference call, press the line button of the
call you want to continue.
Message Window
Choose settings.
Record outgoing announcement
Set clock or review time.
Choose feature.
Skip a message.
Stop message
playback.
Line Ringing Lights
Turn Answering
System On or Off.
Message playback light.
Repeat
a message.
Listen to messages.
Delete messages.
Memory
dialing buttons.
Press before memory
button to access "gray"
memory numbers.
Record a memo
or phone call.
Volume Up or Down
Store numbers
in memory.
Use Flash to access
subscriber services.
Redial last
number called.
Press for Speakerphone.
Temporary Tone
Use for conference calls.
Microphone
Press to
select line.
Line-in-Use Light
Speakerphone-in-Use Light
Press to put a call on hold.
Insert a pause when
storing memory numbers.
Mute the microphone.
T E L E P H O N E M E M O R Y
This telephone can store up to 16 telephone
numbers, each up to 16 digits long.
DIRECTORY CARD
DIALING A STORED NUMBER
Remove the plastic cover from the memory
button area to write your telephone
numbers for both lines in the spaces pro-
vided on the card.
1 Lift the handset
— OR —
Press K
— OR —
Press L or l.
2 Listen for a dial tone.
3 Press a memory button to dial a one-
touch number
— OR —
Press W and then a memory button
NOTE: The number stored in memory may
be lost if the batteries are missing or low
on power and there is a power failure.
You can also write names or telephone
numbers for each memory location. The
eight white spaces on the directory card
are for numbers you can dial by pressing
the memory button next to the number. The
eight gray spaces are for numbers you can
dial by pressing W, then the memory
button next to the number.
STORING A NUMBER IN MEMORY
1 Press p.
2 Enter the telephone number. To insert a
hyphen between digits, press _. The
screen displays the number as you
enter it.
3 Press a memory button to store the
number in a white space (for one-touch
dialing)
to dial a two-touch number.
VIEWING NUMBERS IN MEMORY
To view a number when the phone is not
in use, press the memory button (or W
and then the memory button) where the
number is stored. The number is displayed
but not dialed.
STORING A PAUSE
— OR —
Press W and then a memory button
to store the number in a grey space (for
two-touch dialing).
IN A MEMORY DIAL NUMBER
To store a 2-second pause as part of a
number, press _ twice (a P is
displayed).
You will hear two beeps to confirm the
number has been stored. If you hear a long
sequence of beeps and the screen displays
a series of “Es,” you have not correctly
stored the number. Try again.
To store a 30-second “halt” as part of a
number, press _ 3 times (an H is
displayed).
CLEAR A MEMORY LOCATION
1 Press p.
2 Press the memory button (or press W
and then the memory button) of the
location you want to clear.
To resume dialing after a “halt,” press a
memory button.
NOTE: You may choose to store
emergency numbers in memory locations.
This feature is provided only as a
convenience and the manufacturer
assumes no responsibility for customer
reliance upon the memory feature.
STORING A NUMBER JUST DIALED
1 Press p.
2 Press (.
3 Press a memory button (or W and
then a memory button).
A N S W E R I N G S Y S T E M O P E R A T I O N
LINE SELECTION OPTIONS
The system is preset so that when you lift
the handset or press K, it will choose
the ringing line. The system is preset to
choose Line 1 (preferred) if both lines are
are not in use.
VOICE MAILBOXES
RECORD AN ANNOUNCEMENT
This system provides four voice mailboxes
for you to customize. Mailbox 1 normally
handles calls received on Line1. Mailbox
2 normally handles calls received on Line
2. Two secondary mailboxes, 3 and 4, can
be accessed by touch tone callers on either
Line 1 or Line 2.
1 Press A.
2 Choose the announcement location by
pressing s until the appropriate
mailbox is displayed.
3 Press R. Begin speaking after the
beep.
4 When you are finished, press S.
You will hear your new announcement.
5 Repeat Steps 1-4 to record another
announcement
To change the selection option:
1 Press p.
2 Press F.
3 The line status lights showthecurrent option
Steady light indicates preferred line
Flashing light indicates line selected
if other line is in use
Light off indicates line is never
automatically selected.
4 To choose a new preferred line, press
ANNOUNCEMENT OPTIONS
— OR —
Press S.
You can record up to 4 different primary
announcements —A, B, C, andAO. Each
announcement can be presented to callers
on either Line 1 or Line 2. (If you choose
not to record an announcement, or if your
announcement is lost because of a power
failure, the system has a back-up an-
nouncement.) You can assign the same
announcement to both Line 1 and Line 2,
or you can assign different announcements
to each line. If you are using the second-
ary mailboxes, you can record separate
announcements for Mailboxes 3 and 4.
Callers need to press 3 or 4 to access Mail-
box 3 or Mailbox 4.
REVIEW YOUR ANNOUNCEMENT
1 Press A.
2 Press s to choose the announce-
ment you want to review (A, B, C, AO,
MBOX 3, MBOX 4).
3 Press P to hear the selected
announcement.
L or l.
5 To set the remaining line so it is never
automatically selected, press * to turn
the remaining light off.
To set the remaining line so it is selected
when ringing or when preferred line is
in use, press # so the remaining light is
flashing.
6 Press p when you are finished.
NOTE: The system provides about 23 min-
utes of total recording time for announce-
ments and callers’ messages.
A N S W E R I N G S Y S T E M O P E R A T I O N
SECONDARY MAILBOX
ANNOUNCE ONLY
You can set the system to play an
announcement, but not record messages,
for callers who access Mailbox 3 or 4.
1 Press A.
2 Press s to choose MBOX 3 or
MBOX 4.
3 Press F.
MESSAGE WINDOW
SAVE MESSAGES
The system automatically saves messages
until you delete them.
The display you see in the message
window indicates the number of messages
that have been recorded in each mailbox.
RECORDING A MEMO
MESSAGE ALERT
A memo is stored as a message, and is
played back like a message. The memo
can be up to 4 minutes long. You can
select a mailbox for the memo.
The message light indicates whether or not
you have messages. If there are new
messages, the light flashes. If there are
messages, but no new ones, the light is on
steady.
4 Press 1 to set to Announce Only (AO).
Press 0 to turn off Announce Only.
1 Press R. The system beeps and
begins recording.
2 Speak toward the microphone; your
memo can be up to 4 minutes long. The
message window displays 1-.
3 Press S when you are finished
recording.
NOTE: You cannot select Announce Only
for Mailboxes 3 and 4 unless the mailbox
has an announcement.
To set the system to beep every 15
seconds to notify you of new messages:
1 Press F until the screen displays
ALERT.
2 Press 1 to turnAlert on. Press 0 to turn
Alert off.
ANSWER CALLS
To choose which lines the system will
answer, or to turn the system off, press
O. Pressing O repeatedly cycles
through in the following manner
only Line 1 on
DELETE MESSAGES
3 Press S when you are finished. The
message window displays ALERT.
To delete messages for all lines and mail-
boxes, both Line 1 and Line 2 should be
displayed in the message window. If they
are not, press 0.
PLAY MESSAGES
only Line 2 on
both Lines on
entire system off.
To play messages for all lines and mail-
boxes, both Line 1 and Line 2 should be
displayed in the message window. If they
are not, press 0.
To delete all messages, hold down D,
until the system announces “Messages
deleted.”
RING SELECT/TOLL SAVER
To delete messages for a selected line or
mailbox, press s until the line or
mailboxyouwantisdisplayed. Thenhold
down D until the system
announces “Messages deleted.”
If there are new messages among those
you are trying to delete, the system
beeps 5 times and does not delete any
messages.
To delete a specific message, press D
while the message is playing. You can
press r to replay a message after
listening to it, before pressing D.
To play all messages, press P.
To play new messages, hold down P
until the system begins playing.
To select messages from only one line or
only one mailbox, press the number
of the line or mailbox you want, or
press s until the line or mailbox
you want is displayed.
To play all messages for the selected line
or mailbox, press P.
To play new messages forthe selected line
or mailbox, hold down P until the
system begins playing.
1 Press F until the screen displays
RINGS, and the line you choose.
2 Press a number key (1 - 7) to select the
number of times the line rings before the
system answers. To select Toll Saver,
press 8 (the machine to answer after 4
rings when you have no messages, after
2 rings when you have messages), or
press 9 (the machine to answer after 6
rings when you have no messages, after
4 rings when you have messages).
3 Repeat Steps 1 and 2 to set the number
of rings for the other line.
4 Press S when you are finished.
A N S W E R I N G S Y S T E M O P E R A T I O N
Set the Priority Calling Code to any num-
REPEAT/REVIEW MESSAGES
To repeat an entire message, tap r.
To return to an earlier message, press
r two or more times until the
number of the desired message is
displayed.
To repeat part of a message (review),
hold down r for a few seconds,
then release it to resume playing. (The
system beeps while the button is held.)
RECORDING A PHONE CONVERSATION
ber between 500 and 999, except for the
current Remote Access Code. The preset
code is 999.
1 Press F until the Priority Calling
Code is displayed.
1 Press R at any time during a phone
conversation.
2 The message window displays 2-.
3 Press S when you are finished.
The system stores the recorded conversa-
tion as a message on the line you were using.
2 Usethenumberkeystoenteryournewcode.
3 Press S when you are finished.
NOTE: This unit does not sound warning
beeps to alert the other party that the call
is being recorded. To ensure that you are
in compliance with any state and federal
regulations that concern recording a
telephone call, you should start the
recording process and then inform the
caller that you are recording the call.
CALL SCREENING/CALL INTERCEPT
Adjust the volume using + or -,
so that you can hear a caller’s voice. To
take the call, press the appropriate line
button, or lift the handset of another phone
on the same line. The system stops record-
ing and resets to answer the next call. If
the announcement doesn’t stop, tap the
switchhook, or press S.
FORWARD/SKIP MESSAGES
To skip to the next message, tap f.
To skip part of a message (cue), hold
down f for a few seconds, then
release it to resume playing. (The
system beeps while the button is held.)
To stop playing messages, press S.
WHEN MEMORY IS FULL
The system can record about 23 minutes
of announcements and messages, or a
maximum of 50 messages. When memory
is full, the ON/OFF lights flash rapidly, the
screen displays FULL, and the system
answers calls after 10 rings and announces
“Memory is full.”
To set your system so you do not hear the
announcement while screening calls.
1 Press F until the screen displays
ANNC PLAY.
2 Press 0 for ANNC SILENT. Press 1
for ANNC PLAY.
PRIORITY CALLING
Callers using a touch tone phone can
signal you with the Priority Calling Code
you give them. Your caller should
1 Dial your telephone number.
3 Press S when you are finished.
2 When the announcement begins, enter
the current Priority Calling Code.
3 The system beeps 3 times, then pauses.
This pattern is repeated for 30 seconds,
or until someone picks up the call. The
beeps can be heard on both ends of the call.
REMOTE ACCESS CODE
The Remote Access Code is preset to 500.
To review or change the code (at home)
1 Press F until the screen displays
the current Remote Access Code.
2 Use the number keys to enter a new code
(between 500 and 999, except the current
Priority Calling Code).
If the call is not answered within 30
seconds, the beeps stop and the caller can
press * to leave a message.
3 Press S when you are finished.
2
Answering System 1872
1 Dial telephone number and wait
for system to answer.
2 Enter Remote Access Code.
3 Listen for messages
— OR —
Enter touch tone command.
4 Hang up to save messages.
Your Remote Access Code ______
© Copyright 1998 Philips Consumer Communications L.P.
All Rights Reserved Printed in Mexico
848229530 Issue 1AT&T
2
Answering System 1872
1 Dial telephone number and wait
for system to answer.
2 Enter Remote Access Code.
3 Listen for messages
— OR —
Enter touch tone command.
4 Hang up to save messages.
Your Remote Access Code ______
© Copyright 1998 Philips Consumer Communications L.P.
All Rights Reserved Printed in Mexico
848229530 Issue 1AT&T
Play all messages
Play all new messages
Play all messages
7
6
in a mailbox 17, 27, 37, or 47
Play new messaes
in a mailbox 16, 26, 36, or 46
Repeat message
2
Skip message
5
Delete selected message
Delete all message
Delete all message
3
03
in a mailbox 13, 23, 33, or 43
Turn system on
Turn system off
00
88
Change RemoteAccess Code 99
Help menu
#
Play all messages
Play all new messages
Play all messages
7
6
in a mailbox 17, 27, 37, or 47
Play new messaes
in a mailbox 16, 26, 36, or 46
Repeat message
2
Skip message
5
Delete selected message
Delete all message
Delete all message
3
03
in a mailbox 13, 23, 33, or 43
Turn system on
Turn system off
00
88
Change RemoteAccess Code 99
Help menu
#
|