NF6-GLAN
User Manual
Version 1.2
Published May 2009
Copyright©2009 ASRock INC. All rights reserved.
1
Contents
1. Introduction ............................................................ 5
1.1 Package Contents ..................................................................... 5
1.2 Specifications ............................................................................ 6
1.3 Motherboard Layout ................................................................... 10
1.4 ASRock HD 6CH I/O .................................................................. 11
2. Installation ............................................................. 12
Pre-installation Precautions ................................................................ 12
2.1 CPU Installation ......................................................................... 13
2.2 Installation of CPU Fan and Heatsink......................................... 13
2.3 Installation of Memory Modules (DIMM) .................................... 14
2.4 Expansion Slots (PCI Express and PCI Slots) .................................. 16
2.5 Jumpers Setup.......................................................................... 17
2.6 Onboard Headers and Connectors.......................................... 18
2.7 HDMI_SPDIF Header ConnectionGuide .................................... 23
2.8 SATAII Hard Disk Setup Guide .................................................. 24
2.9 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks
Installation ................................................................................. 25
2.10 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs .... 25
2.11 SATA / SATAII HDD Hot Plug Feature and Operation Guide ..... 26
2.12 Driver Installation Guide ............................................................ 28
2.13 Installing Windows® 2000 / XP / XP 64-bit / VistaTM
VistaTM 64-bit Without RAID Functions ..................................... 28
2.14 Installing Windows® 2000 / XP / XP 64-bit / VistaTM
/
/
VistaTM 64-bit With RAID Functions........................................... 28
2.14.1 Installing Windows® 2000 / XP / XP 64-bit With RAID
Functions ...................................................................... 28
2.14.2 Installing Windows® VistaTM / VistaTM 64-bit With RAID
Functions ...................................................................... 29
2.15 Untied Overclocking Technology .............................................. 30
3. BIOS SETUP UTILITY ................................................... 31
3.1 Introduction ............................................................................... 31
3.1.1 BIOS Menu Bar ............................................................... 31
3.1.2 Navigation Keys ............................................................. 31
3.2 Main Screen.............................................................................. 32
3.3 Advanced Screen .................................................................... 33
3.3.1 CPU Configuration .......................................................... 33
3.3.2 Chipset Configuration ..................................................... 38
3.3.3 ACPI Configuration .......................................................... 39
3.3.4 IDE Configuration............................................................. 40
3
3.3.5 PCIPnP Configuration ...................................................... 42
3.3.6 Floppy Configuration ...................................................... 43
3.3.7 Super IO Configuration ................................................... 43
3.3.8 USB Configuration .......................................................... 44
3.4 Hardware Health Event Monitoring Screen ............................. 45
3.5 Boot Screen .............................................................................. 46
3.5.1 Boot Settings Configuration ........................................... 46
3.6 Security Screen........................................................................ 47
3.7 Exit Screen ............................................................................... 48
4. Software Support ................................................... 49
4.1 Install Operating System........................................................... 49
4.2 Support CD Information ............................................................. 49
4.2.1 Running Support CD ....................................................... 49
4.2.2 Drivers Menu .................................................................. 49
4.2.3 Utilities Menu ................................................................... 49
4.2.4 Contact Information ........................................................ 49
4
1. Introduction
Thank you for purchasing ASRock NF6-GLAN motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
If you require technical support related to this motherboard, please visit
our website for specific information about the model you are using.
1.1 Package Contents
1 x ASRock NF6-GLAN Motherboard
(ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm)
1 x ASRock NF6-GLAN Quick Installation Guide
1 x ASRock NF6-GLAN Support CD
1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)
1 x 3.5-in Floppy Drive Ribbon Cable
1 x Serial ATA (SATA) Data Cable (Optional)
1 x Serial ATA (SATA) HDD Power Cable (Optional)
1 x “ASRock HD 6CH I/O” I/O Shield
5
1.2
S
p
e
c
i
f
i
c
a
t
i
o
n
s
Platform
CPU
- ATX Form Factor: 12.0-in x 8.0-in, 30.5 cm x 20.3 cm
- Support for Socket AM2+ / AM2 processors: AMD PhenomTM
FX / Phenom / Athlon 64 FX / Athlon 64 X2 Dual-Core / Athlon
X2 Dual-Core / Athlon 64 / Sempronprocessor
- Support for AM3 processors: AMD PhenomTM II X4 / X3 and
Athlon II X4 / X3 / X2 processors
- Supports AMD’s Cool ‘n’ QuietTM Technology
- FSB 1000 MHz (2.0 GT/s)
- Supports Untied Overclocking Technology (see CAUTION 1)
- Supports Hyper-Transport Technology
- NVIDIA® GeForce 6150SE / nForce 430 or
GeForce 7025 / nForce 630a
Chipset
Memory
-Dual Channel DDR2 Memory Technology (see CAUTION 2)
- 4 x DDR2 DIMM slots
- Support DDR2 1066/800/667/533 non-ECC, un-buffered
memory (see CAUTION 3)
- Max. capacity of system memory: 16GB (see CAUTION 4)
- 1 x PCI Express x16 slot
Expansion Slot
- 2 x PCI Express x1 slots
- 3 x PCI slots
Audio
LAN
- 5.1 CH Windows® VistaTM Premium Level HDAudio
(Realtek ALC662 Audio Codec)
- Gigabit LAN 10/100/1000 Mb/s
- Giga PHY Realtek RTL8211B
- Supports Wake-On-LAN
Rear Panel I/O
ASRock HD 6CH I/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP Support)
- 6 x Ready-to-Use USB 2.0 Ports
- 1 x RJ-45 LAN Port
- HDAudio Jack: Line in / Front Speaker / Microphone
- 4 x Serial ATAII 3.0Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 0+1, RAID 5 and JBOD), NCQ and “Hot Plug”
functions (see CAUTION 5)
Connector
- 1 x ATA133 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
6
- 1 x HDMI_SPDIF header
- CPU/Chassis FAN connector
- 24 pin ATX power connector
- 4 pin 12V power connector
- CD in header
- Front panel audio connector
- 2 x USB 2.0 headers (support 3 USB 2.0 ports)
(see CAUTION 6)
- 1 x WiFi header (see CAUTION 7)
- 4Mb AMI BIOS
BIOS Feature
- AMI Legal BIOS
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- SMBIOS 2.3.1 Support
Support CD
- Drivers, Utilities, AntiVirus Software (Trial Version)
- ASRock OC Tuner (see CAUTION 8)
- Instant Boot
Unique Feature
- Hybrid Booster:
- CPU Frequency Stepless Control (see CAUTION 9)
- ASRock U-COP (see CAUTION 10)
- Boot Failure Guard (B.F.G.)
-ASRock AM2 Boost: ASRock Patented Technology to boost
memory performance up to 12.5% (see CAUTION 11)
- CPU Temperature Sensing
Hardware
Monitor
- Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, Vcore
OS
- Microsoft® Windows® 2000 / XP / XP 64-bit / VistaTM
VistaTM 64-bit compliant
/
Certifications
- FCC, CE, Microsoft® WHQL Certificated
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using the third-
party overclocking tools. Overclocking may affect your system stability, or even
cause damage to the components and devices of your system. It should be done at
your own risk and expense. We are not responsible for possible damage caused by
overclocking.
7
CAUTION!
1. This motherboard supports Untied Overclocking Technology. Please read
“Untied Overclocking Technology” on page 30 for details.
2. This motherboard supports Dual Channel Memory Technology. Before
you implement Dual Channel Memory Technology, make sure to read
the installation guide of memory modules on page 14 for proper
installation.
3. Whether 1066MHz memory speed is supported depends on the AM2+ CPU
you adopt. If you want to adopt DDR2 1066 memory module on this
motherboard, please refer to the memory support list on our website for
the compatible memory modules.
4. Due to the operating system limitation, the actual memory size may be
less than 4GB for the reservation for system usage under Windows® XP
and Windows® VistaTM. For Windows® XP 64-bit and Windows® VistaTM 64-
bit with 64-bit CPU, there is no such limitation.
5. Before installing SATAII hard disk to SATAII connector, please read the “SATAII
Hard Disk Setup Guide” on page 24 to adjust your SATAII hard disk drive to
SATAII mode. You can also connect SATA hard disk to SATAII connector
directly.
6. Power Management for USB 2.0 works fine under Microsoft® Windows®
VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
7. WiFi header supports WiFi+AP function with ASRock WiFi-802.11g or
WiFi-802.11n module, an easy-to-use wireless local area network
(WLAN) adapter. It allows you to create a wireless environment and
enjoy the convenience of wireless network connectivity. Please visit our
website for the availability of ASRock WiFi-802.11g or WiFi-802.11n
module.
8. It is a user-friendly ASRock overclocking tool which allows you to surveil
your system by hardware monitor function and overclock your hardware
devices to get the best system performance under Windows® environment.
Please visit our website for the operation procedures of ASRock OC
9. Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
8
10. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC
system.
11. This motherboard supports ASRock AM2 Boost overclocking technology. If
you enable this function in the BIOS setup, the memory performance will
improve up to 12.5%, but the effect still depends on the AM2 CPU you
adopt. Enabling this function will overclock the chipset/CPU reference clock.
However, we can not guarantee the system stability for all CPU/DRAM
configurations. If your system is unstable after AM2 Boost function is enabled,
it may not be applicative to your system. You may choose to disable this
function for keeping the stability of your system.
9
1.3 Motherboard Layout
1
2
3
5
7
4
6
20.3cm (8.0-in)
PS2_USB_PW1
PS2
Mouse
CPU_FAN1
ATX12V1
USB 2.0
T: USB2
B: USB3
USB 2.0
T: USB0
B: USB1
Top:
RJ-45
IDE1
USB 2.0
T: USB4
B: USB5
8
31
Dual Channel
AM2+
PCI
PCIE1
30
29
AM2
EXPRESS
LAN
PHY
PCIE2
CLRCMOS1
1
9
NF6-GLAN
10
11
NVIDIA
GeForce 6150SE
/ nForce 430
or
PCIE3/DE
28
RoHS
SATAII
PCI1
GeForce 7025
/ nForce 630a
Chipset
12
27
26
25
1
13
14
15
USB8
USB6_7
1
PCI2
HDMI_SPDIF1
1
1
4Mb
BIOS
WIFI
AUDIO
CODEC
RAID
PCI3
CHA_FAN1
PANEL
PLED PWRBTN
1
16
CD1
FLOPPY1
HD_AUDIO1
SPEAKER1
1
1
1
1
IR1
HDLED RESET
23
21
17
20 19 18
24
22
1
2
3
4
5
6
PS2_USB_PW1 Jumper
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
SATAII Connector (SATAII_2(PORT1.1), Red)
System Panel Header (PANEL1)
Chassis Speaker Header (SPEAKER 1)
NVIDIA Chipset
ATX 12V Power Connector (ATX12V1)
CPU Heatsink Retention Module
AM2 940-Pin CPU Socket
CPU Fan Connector (CPU_FAN1)
2 x 240-pin DDR2 DIMM Slots
Chassis Fan Connector (CHA_FAN1)
Infrared Module Header (IR1)
Floppy Connector (FLOPPY1)
Internal Audio Connector: CD1 (Black)
Front Panel Audio Header (HD_AUDIO1)
WiFi Header (WIFI)
(Dual Channel A: DDRII_1, DDRII_2; Yellow)
2 x 240-pin DDR2 DIMM Slots
7
(Dual Channel B: DDRII_3, DDRII_4; Orange)
Primary IDE Connector (IDE1, Blue)
Clear CMOS Jumper (CLRCMOS1)
SATAII Connector (SATAII_4 (PORT 2.1), Red)
SATAII Connector (SATAII_3 (PORT 2.0), Red)
SATAII Connector (SATAII_1 (PORT 1.0), Red)
USB 2.0 Header (USB8, Blue)
8
9
HDMI_SPDIF Header (HDMI_SPDIF1)
PCI Slots (PCI1- 3)
10
11
12
13
14
15
PCI Express x1 Slot (PCIE3/DE)
PCI Express x16 Slot (PCIE2)
PCI Express x1 Slot (PCIE1)
ATX Power Connector (ATXPWR1)
USB 2.0 Header (USB6_7, Blue)
BIOS SPI Chip
1 0
1.4 ASRock HD 6CH I/O
1
2
3
4
5
11
10
9
6
8
7
1
2
3
4
5
6
Parallel Port
7
8
9
USB 2.0 Ports (USB01)
USB 2.0 Ports (USB23)
COM Port
RJ-45 Port
Line In (Light Blue)
Line Out (Lime)
Microphone (Pink)
USB 2.0 Ports (USB45)
10 PS/2 Keyboard Port (Purple)
11 PS/2 Mouse Port (Green)
* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. Please refer to below steps for the software setting of Multi-Streaming.
For Windows® XP:
After restarting your computer, you will find “Mixer” tool on your system. Please select “Mixer
ToolBox”
, click “Enable playback multi-streaming”, and click “ok”. Choose “2CH” or
“4CH” and then you are allowed to select “Realtek HDA Primary output” to use Rear Speaker
and Front Speaker, or select “Realtek HDA Audio 2nd output” to use front panel audio. Then
reboot your system.
For Windows® VistaTM
:
After restarting your computer, please double-click “Realtek HD Audio Manager” on the
system tray. Set “Speaker Configuration” to “Quadraphonic” or “Stereo”. Click “Device
advanced settings”, choose “Make front and rear output devices playbacks two different audio
streams simultaneously”, and click “ok”. Then reboot your system.
1 1
2. Installation
This is an ATX form factor (12.0-in x 8.0-in, 30.5 cm x 20.3 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to en-
sure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1.
2.
Unplug the power cord from the wall socket before touching any
component.
To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
Hold components by the edges and do not touch the ICs.
Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.
3.
4.
5.
1 2
2.1
C
P
U
I
n
s
t
a
l
l
a
t
i
o
n
Step 1. Unlock the socket by lifting the lever up to a 90o angle.
Step 2. Position the CPU directly above the socket such that the CPU corner with
the golden triangle matches the socket corner with a small triangle.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the CPU
into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.
Lever 90° Up
CPU Golden Triangle
Socker Corner Small Triangle
STEP 1:
STEP 2 / STEP 3:
STEP 4:
Match The CPU Golden Triangle Push Down And Lock
Lift Up The Socket Lever
To The Socket Corner Small
Triangle
The Socket Lever
2.2 Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat
dissipation. Make sure that the CPU and the heatsink are securely fas-
tened and in good contact with each other. Then connect the CPU fan to
the CPU FAN connector (CPU_FAN1, see Page 10, No. 5). For proper
installation, please kindly refer to the instruction manuals of the CPU fan
and the heatsink.
1 3
2.3 Installation of Memory Modules (DIMM)
This motherboard provides four 240-pin DDR2 (Double Data Rate 2) DIMM slots,
and supports Dual Channel Memory Technology. For dual channel configuration,
you always need to install identical (the same brand, speed, size and chip-
type) DDR2 DIMM pair in the slots of the same color. In other words, you have to
install identical DDR2 DIMM pair in Dual Channel A (DDRII_1 and DDRII_2;
Yellow slots; see p.10 No.6) or identical DDR2 DIMM pair in Dual Channel B
(DDRII_3 andDDRII_4; Orange slots; see p.10No.7), so that Dual Channel Memory
Technology can be activated. This motherboard also allows you to install four
DDR2 DIMMs for dual channel configuration, and please install identical DDR2
DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration
Table below.
Dual Channel Memory Configurations
DDRII_1
DDRII_2
DDRII_3
DDRII_4
(Yellow Slot) (Yellow Slot) (Orange Slot) (Orange Slot)
(1)
(2)
(3)*
Populated
-
Populated
-
-
-
Populated
Populated
Populated
Populated
Populated
Populated
* For the configuration (3), please install identical DDR2 DIMMs in all four
slots.
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of yellow
slots (DDRII_1 and DDRII_2), or in the set of orange slots (DDRII_3
and DDRII_4).
2. If only one memory module or three memory modules are installed
in the DDR2 DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDRII_1
and DDRII_3, it is unable to activate the Dual Channel Memory
Technology .
4. It is not allowed to install a DDR memory module into DDR2 slot;
otherwise, this motherboard and DIMM may be damaged.
1 4
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
1 5
2.4 Expansion Slots (PCI and PCI Express Slots)
There are 3 PCI slots and 3 PCI Express slots on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE slots:
PCIE1 (PCIE x1 slot) is used for PCI Express cards with x1 lane
width cards, such as Gigabit LAN card, SATA2 card, etc.
PCIE2 (PCIE x16 slot) is used for PCI Express cards with x16 lane
width graphics cards.
PCIE3/DE (PCIE x1 slot) is used for PCI Express cards with x1 lane
width cards, such as Gigabit LAN card, SATA2 card and ASRock
PCIE_DEcard.
If you want to use ASRock DeskExpress function on this motherboard,
please install ASRock PCIE_DE card on PCIE3/DE slot.
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Step 3. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 4. Fasten the card to the chassis with screws.
1 6
2.5
J
u
m
p
e
r
s
S
e
t
u
p
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper
Setting
1_2
2_3
PS2_USB_PW1
(see p.10, No. 1)
Short pin2, pin3 to enable
+5VSB (standby) for PS/2 or
USB wake up events.
+5V
+5VSB
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
Clear CMOS Jumper
1_2
2_3
(CLRCMOS1)
(see p.10, No. 9)
Default
Clear CMOS
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3
on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right
after you update the BIOS. If you need to clear the CMOS when you just finish
updating the BIOS, you must boot up the system first, and then shut it down
before you do the clear-CMOS action.
1 7
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
FLOPPY1
Pin1
(see p.10 No. 22)
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.10 No. 8)
IDE1
PIN1
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100/133 cable
Note: Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These four SerialATAII (SATAII)
connectors support SATAII
or SATA hard disk for internal
storage devices. The current
SATAII interface allows up to
3.0 Gb/s data transfer rate.
(SATAII_1 (PORT 1.0): see p.10,No. 12)
(SATAII_2 (PORT 1.1): see p.10,No. 16)
(SATAII_3 (PORT 2.0): see p.10,No. 11)
(SATAII_4 (PORT 2.1): see p.10,No. 10)
SerialATA (SATA)
Data Cable
Either end of the SATA data cable
can be connected to the SATA /
SATAII hard disk or the SATAII
connector on the motherboard.
(Optional)
1 8
Serial ATA (SATA)
Power Cable
(Optional)
Please connect the black end of
SATA power cable to the power
connector on each drive. Then
connect the white end of SATA
power cable to the power
connect to the SATA HDD
powerconnector
connect to the
powersupply
connector of the power supply.
USB_PWR
USB 2.0 Headers
(9-pin USB6_7)
Besides six default USB 2.0
ports on the I/O panel, there are
two USB 2.0 headers on this
motherboard. USB6_7headercan
support two USB 2.0 ports, and
USB8 header can support one
USB 2.0 port.
P-7
P+7
GND
DUMMY
(see p.10 No. 14)
1
GND
P+6
P-6
USB_PWR
1
(4-pin USB8)
GND
P+8
P-8
USB_PWR
(see p.10 No. 13)
WiFi Header
(11-pin WIFI)
This header supports WiFi+AP
function with ASRock
USB+5V_2
NC
NC
GND1
NC
(see p.10 No. 25)
WiFi-802.11g or WiFi-802.11n
module, an easy-to-use wireless
local area network (WLAN)
adapter. It allows you to create a
wirelessenvironmentandenjoythe
convenience of wireless network
connectivity.
+3SVB
1
PME#
GND1
D0+
D0-
USB+5V_1
If you don’t plan to use WiFi+AP function on this motherboard, this header can be
used as a 4-Pin USB 2.0 header to support one USB 2.0 port. To connect the
4-Pin USB device cable to this header, please refer to this
picture for proper installation.
IRTX
+5V
DUMMY
Infrared Module Header
This header supports an
(5-pin IR1)
optional wireless transmitting
and receiving infrared module.
1
(see p.10 No. 21)
GND
IRRX
Internal Audio Connectors
(4-pin CD1)
This connector allows you
to receive stereo audio input
from sound sources such as
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
(CD1: see p.10 No. 23)
CD1
1 9
Front Panel Audio Header
(9-pin HD_AUDIO1)
GND
PRESENCE#
MIC_RET
OUT_RET
This is an interface for the front
panel audio cable that allows
convenient connection and
control of audio devices.
(see p.10, No. 24)
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on
the chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from
[Auto] to [Enabled].
F. Enter Windows system. Click the icon on the lower right hand
taskbar to enter Realtek HD Audio Manager.
For Windows® 2000 / XP / XP 64-bit OS:
Click “Audio I/O”, select “Connector Settings”
, choose
“Disable front panel jack detection”, and save the change by
clicking “OK”.
For Windows® VistaTM / VistaTM 64-bit OS:
Click the right-top “Folder” icon
, choose “Disable front
panel jack detection”, and save the change by clicking “OK”.
G. To activate the front mic.
For Windows® 2000 / XP / XP 64-bit OS:
Please select “Front Mic” as default record device.
If you want to hear your voice through front mic, please deselect "Mute"
icon in “Front Mic” of “Playback” portion.
For Windows® VistaTM / VistaTM 64-bit OS:
Go to the "Front Mic" Tab in the Realtek Control panel.
Click "Set Default Device" to make the Front Mic as the default record
device.
PLED+
System Panel Header
This header accommodates
several system front panel
functions.
PLED-
PWRBTN#
GND
(9-pin PANEL1)
(see p.10 No. 17)
1
DUMMY
RESET#
GND
HDLED-
HDLED+
2 0
Chassis Speaker Header
Please connect the chassis
speaker to this header.
1
SPEAKER
DUMMY
DUMMY
+5V
(4-pin SPEAKER 1)
(see p.10 No. 18)
Chassis Fan Connector
(3-pin CHA_FAN1)
Please connect a chassis fan
cable to this connector and
match the black wire to the
ground pin.
GND
+12V
CHA_FAN_SPEED
(see p.10 No. 20)
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.10 No. 5)
Please connect the CPU fan
cable to this connector and
match the black wire to the
ground pin.
+12V
CPU_FAN_SPEED
FAN_SPEED_CONTROL
GND
1
2
3
4
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
1
13
ATX Power Connector
Please connect an ATX power
supply to this connector.
(24-pin ATXPWR1)
(see p.10, No. 31)
12
24
1
Though this motherboard provides 24-pin ATX power connector,
it can still work if you adopt a traditional 20-pin ATX power supply.
To use the 20-pin ATX power supply, please plug your power
supply along with Pin 1 and Pin 13.
13
20-PinATX Power Supply Installation
12
24
ATX 12V Power Connector
(4-pin ATX12V1)
Please note that it is necessary
to connect a power supply with
ATX 12V plug to this connector.
Failing to do so will cause power
up failure.
(see p.10 No. 2)
2 1
HDMI_SPDIFHeader
(3-pin HDMI_SPDIF1)
(see p.10 No. 26)
HDMI_SPDIF header, providing
SPDIF audio output to HDMI VGA
card, allows the system to
connect HDMIDigital TV/
projector/LCD devices. Please
connect the HDMI_SPDIF
connector of HDMI VGA card to
this header.
1
GND
SPDIFOUT
+5V
HDMI_SPDIFCable
Please connect the black end (A)
of HDMI_SPDIF cable to the
HDMI_SPDIF header on the
motherboard. Then connect the
white end (B or C) of
C
(Optional)
B
A
HDMI_SPDIF cable to the
HDMI_SPDIF connector of HDMI
VGA card.
A. black end
+5V
B. white end (2-pin)
C. white end (3-pin)
SPDIFOUT
SPDIFOUT
blue
blue
GND
black
GND
black
SPDIFOUT
blue
GND
black
2 2
2.7 HDMI_SPDIF Header Connection Guide
HDMI (High-Definition Multi-media Interface) is an all-digital audio/video specification,
which provides an interface between any compatible digital audio/video source,
such as a set-top box, DVD player, A/V receiver and a compatible digital audio or
video monitor, such as a digital television (DTV). A complete HDMI system requires a
HDMI VGA card and a HDMI ready motherboard with a HDMI_SPDIF header. This
motherboard is equipped with a HDMI_SPDIF header, which provides SPDIF audio
output to HDMI VGA card, allows the system to connect HDMI Digital TV/projector/
LCD devices. To use HDMI function on this motherboard, please carefully follow the
below steps.
•
Step 1. Install the HDMI VGA card to the PCI Express Graphics slot on this
motherboard. For the proper installation of HDMI VGA card, please refer
to the installation guide on page 16.
Step 2. Connect the black end (A) of HDMI_SPDIF cable to the
HDMI_SPDIF header (HDMI_SPDIF1, yellow, see page 10,
No. 26) on the motherboard.
Make sure to correctly connect the HDMI_SPDIF cable to the motherboard and the
HDMI VGA card according to the same pin definition. For the pin definition of
HDMI_SPDIF header and HDMI_SPDIF cable connectors, please refer to page 22.
For the pin definition of HDMI_SPDIF connectors on HDMI VGA card, please refer to
the user manual of HDMI VGA card vendor. Incorrect connection may cause
permanent damage to this motherboard and the HDMI VGA card.
Step 3. Connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF
connector of HDMI VGA card. (There are two white ends (2-pin and 3-pin)
on HDMI_SPDIF cable. Please choose the appropriate white end according
to the HDMI_SPDIF connector of the HDMI VGA card you install.
white end
(2-pin) (B)
white end
(3-pin) (C)
Please do not connect the white end of HDMI_SPDIF cable to the wrong connector
of HDMI VGA card or other VGA card. Otherwise, the motherboard and the
VGA card may be damaged. For example, this picture shows the wrong
example of connecting HDMI_SPDIF cable to the fan connector of PCI
Express VGA card. Please refer to the VGA card user manual for
connector usage in advance.
Step 4. Connect the HDMI output connector on HDMI VGA card to
HDMI device, such as HDTV. Please refer to the user manual
of HDTV and HDMI VGA card vendor for detailed connection
procedures.
Step 5. Install HDMI VGA card driver to your system.
2 3
2.8
S
AT
A
I
I
H
a
r
d
D
i
s
k
S
e
t
u
p
G
u
i
d
e
Before installing SATAII hard disk to your computer, please carefully read below
SATAII hard disk setup guide. Some default setting of SATAII hard disks may not be
at SATAII mode, which operate with the best performance. In order to enable SATAII
function, please follow the below instruction with different vendors to correctly adjust
your SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard disk
may fail to run at SATAII mode.
Western Digital
7
5
6
3
1
8
4
2
If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 5 and pin 6.
SAMSUNG
7
5
6
3
1
8
4
2
If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 3 and pin 4.
HITACHI
Please use the Feature Tool, a DOS-bootable tool, for changing various ATA
features. Please visit HITACHI’s website for details:
The above examples are just for your reference. For different SATAII hard
disk products of different vendors, the jumper pin setting methods may not
be the same. Please visit the vendors’ website for the updates.
2 4
2.9
S
e
r
i
a
l
A
T
A
(
S
AT
A
)
/
S
e
r
i
a
l
AT
A
I
I
(
S
AT
A
I
I
)
H
a
r
d
D
i
s
k
s
Installation
This motherboard adopts NVIDIA® GeForce 6150SE / nForce 430 or GeForce 7025 /
nForce 630a chipset that supports Serial ATA (SATA) / Serial ATAII (SATAII) hard disks
and RAID functions. You may install SATA / SATAII hard disks on this motherboard for
internal storage devices. This section will guide you to install the SATA / SATAII hard
disks.
STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
2.10 Hot Plug and Hot Swap Functions for SATA / SATAII
HDDs
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII
Devices.
NOTE
What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is
called “Hot Plug” for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has
been installed into the SATA / SATAII HDD.
What is Hot Swap Function?
If SATA / SATAII HDDs are built as RAID1 or RAID 5 then it is called
“Hot Swap” for the action to insert and remove the SATA / SATAII
HDDs while the system is still power-on and in working condition.
2 5
2.11
S
AT
A
/
S
ATA
I
I
H
D
D
H
o
t
P
l
u
g
F
e
a
t
u
r
e
a
n
d
O
p
e
r
a
t
i
o
n
Guide
This motherboard supports Hot Plug feature for SATA / SATAII HDD. Please read
below operation guide of SATA / SATAII HDD Hot Plug feature carefully. Before you
process the SATA / SATAII HDD Hot Plug, please check below cable accessories
from the motherboard gift box pack.
A. 7-pin SATA data cable
B. SATA power cable with SATA 15-pin power connector interface
A. SATA data cable (Red)
B. SATA power cable
1x4-pin conventional
SATA 7-pin
connector
The SATA 15-pin power
connector (Black) connect
to SATA / SATAII HDD
power connector (White)
connect to power supply
Caution
1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug
cannot be processed.
2. Even some SATA / SATAII HDDs provide both SATA 15-pin power connector
and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin
conventional power connector interface is definitely not able to support Hot
Plug and will cause the HDD damage and data loss.
Points of attention, before you process the Hot Plug:
1. Below operation procedure is designed only for our motherboard, which supports
SATA / SATAII HDD Hot Plug.
* The SATA / SATAII Hot Plug feature might not be supported by the chipset
because of its limitation, the SATA / SATAII Hot Plug support information of our
motherboard is indicated in the product spec on our website:
2. Make sure your SATA / SATAII HDD can support Hot Plug function from your
dealer or HDD user manual. The SATA / SATAII HDD, which cannot support Hot
Plug function, will be damaged under the Hot Plug operation.
3. Please make sure the SATA / SATAII driver is installed into system properly. The
latest SATA / SATAII driver is available on our support website:
4. Make sure to use the SATA power cable & data cable, which are from our
motherboard package.
5. Please follow below instructions step by step to reduce the risk of HDD crash
or data loss.
2 6
How to Hot Plug a SATA / SATAII HDD:
Points of attention, before you process the Hot Plug:
Please do follow below instruction sequence to process the Hot Plug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1
Step 2
Please connect SATA power cable 1x4-pin end
(White) to the power supply 1x4-pin cable.
Connect SATA data cable to
the motherboard’s SATAII connector.
SATA power cable 1x4-pin
power connector (White)
Step 4
Step 3
Connect SATA 15-pin power cable connector
(Black) end to SATA / SATAII HDD.
Connect SATA data cable to
the SATA / SATAII HDD.
How to Hot Unplug a SATA / SATAII HDD:
Points of attention, before you process the Hot Unplug:
Please do follow below instruction sequence to process the Hot Unplug, improper
procedure will cause the SATA / SATAII HDD damage and data loss.
Step 1
Unplug SATA data cable from SATA / SATAII HDD side.
Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII HDD side.
Step 2
2 7
2.13
I
n
s
t
a
l
l
i
n
g
W
i
n
d
o
w
s®
2000 / XP / XP 64-bit / VistaTM
2.12
D
r
i
v
e
r
I
n
s
t
a
l
l
a
t
i
o
n
G
u
i
d
e
To install the drivers to your system, please insert the support CD to your optical
drive first. Then, the drivers compatible to your system can be auto-detected and
listed on the support CD driver page. Please follow the order from up to bottom
side to install those required drivers. Therefore, the drivers you install can work
properly.
/ VistaTM 64-bit Without RAID Functions
If you just want to install Windows® 2000, Windows® XP, Windows® XP 64-bit,
Windows® VistaTM or Windows® VistaTM 64-bit on your SATA / SATAII HDDs without
RAID functions, you don’t have to make a SATA / SATAII driver diskette. Besides,
there is no need for you to change the BIOS setting. You can start to install Windows®
2000, Windows® XP, Windows® XP 64-bit, Windows® VistaTM or Windows® VistaTM
64-bit on your system directly.
2.14 Installing Windows® 2000 / XP / XP 64-bit / VistaTM
/ VistaTM 64-bit With RAID Functions
If you want to install Windows® 2000, Windows® XP, Windows® XP 64-bit, Windows®
VistaTM or Windows® VistaTM 64-bit OS on your SATA / SATAII HDDs with RAID
functions, please follow below procedures according to the OS you install.
Before installing Windows® 2000 to your system, your Windows® 2000 optical
disk is supposed to include SP4. If there is no SP4 included in your disk, please
visit the below website for proper procedures of making a SP4 disk:
htm#the_integrated_installation_fmay
2.14.1 Installing Windows® 2000 / XP / XP 64-bit With RAID
Functions
If you want to install Windows® 2000, Windows® XP or Windows® XP 64-bit on your
SATA / SATAII HDDs with RAID functions, please follow below steps.
STEP 1: Make a SATA / SATAII Driver Diskette.
A.
B.
Insert the ASRock Support CD into your optical drive to boot your system.
During POST at the beginning of system boot-up, press <F11> key, and
then a window for boot devices selection appears. Please select CD-
ROM as the boot device.
C.
When you see the message on the screen, “Generate Serial ATA driver
diskette [YN]?”, press <Y>.
2 8
D.
E.
Then you will see these messages,
Please insert a blank
formatted diskette into floppy
drive A:
press any key to start
Please insert a floppy diskette into the floppy drive, and press any key.
The system will start to format the floppy diskette and copy SATA / SATAII
drivers into the floppy diskette.
STEP 2: Set Up BIOS.
A.
B.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
Set the “SATA Operation Mode” option to [RAID].
STEP 3: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure RAID function, you need to check the RAID installation
guide in the Support CD for proper configuration. Please refer to the BIOS RAID
installation guide in the following path in the Support CD:
.. \ RAID Installation Guide
STEP 4: Install Windows® 2000 / Windows® XP / Windows® XP 64-bit OS on
your system.
After step1, 2, 3, you can start to install Windows® 2000 / Windows® XP / Windows® XP
64-bit OS on your system. At the beginning of Windows® setup, press F6 to install a
third-party RAIDdriver. When prompted, insert the SATA/ SATAII driver diskette contain-
ing the NVIDIA® RAID driver. After reading the floppy disk, the driver will be presented.
Select the driver to install according to the mode you choose and the OS you install.
NOTE. If you install Windows® 2000 / Windows® XP / Windows® XP 64-bit on IDE
HDDs and want to manage (create, convert, delete, or rebuild) RAID functions
on SATA / SATAII HDDs, you still need to set up “SATA Operation Mode” to [RAID] in
BIOS first. Then, please set the RAID configuration by using the Windows RAID
installation guide in the following path in the Support CD:
.. \ RAID Installation Guide
2.14.2 Installing Windows® VistaTM / VistaTM 64-bit With
RAID Functions
If you want to install Windows® VistaTM or Windows® VistaTM 64-bit on your SATA /
SATAII HDDs with RAID functions, please follow below steps.
STEP 1: Set Up BIOS.
A.
B.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
Set the “SATA Operation Mode” option to [RAID].
2 9
STEP 2: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure RAID function, you need to check the RAID installation
guide in the Support CD for proper configuration. Please refer to the BIOS RAID
installation guide part of the document in the following path in the Support CD:
.. \ RAID Installation Guide
STEP 3: Install Windows® VistaTM / Windows® VistaTM 64-bit OS on your
system.
Insert the Windows® VistaTM / Windows® VistaTM 64-bit optical disk into the optical drive
to boot your system, and follow the instruction to install Windows® VistaTM / Windows®
VistaTM 64-bit OS on your system. When you see “Where do you want to install Windows?
” page, please insert the ASRock Support CD into your optical drive, and click the “Load
Driver” button on the left on the bottom to load the NVIDIA® RAID drivers. NVIDIA® RAID
drivers are in the following path in our Support CD:
.. \ I386 \ Vista (For Windows® VistaTM OS)
.. \ AMD64 \ Vista64 (For Windows® VistaTM 64-bit OS)
After that, please insert Windows® VistaTM / Windows® VistaTM 64-bit optical disk into
the optical drive again to continue the installation.
NOTE. If you install Windows® VistaTM / Windows® VistaTM 64-bit on IDE HDDs and want to
manage (create, convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs,
you still need to set up “SATA Operation Mode” to [RAID] in BIOS first. Then, please set
the RAID configuration by using the Windows RAID installation guide in the following
path in the Support CD:
.. \ RAID Installation Guide
2.15
U
n
t
i
e
d
O
v
e
r
c
l
o
c
k
i
n
g
Te
c
h
n
o
l
o
g
y
This motherboard supports Untied Overclocking Technology, which means during
overclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before you
enable Untied Overclocking function, please enter “Overclock Mode” option of BIOS
setup to set the selection from [Auto] to [CPU, PCIE, Async.]. Therefore, CPU FSB is
untied during overclocking, but PCI / PCIE buses are in the fixed mode so that FSB can
operate under a more stable overclocking environment.
Please refer to the warning on page 7 for the possible overclocking risk
before you apply Untied Overclocking Technology.
3 0
3. BIOS SETUP UTILITY
3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The Flash Memory on the motherboard stores the BIOS SETUP UTILITY. You may run
the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during
the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST
will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the following
BIOS setup screens and descriptions are for reference purpose only,
and they may not exactly match what you see on your screen.
3.1.1 BIOS Menu Bar
The top of the screen has a menu bar with the following selections:
Main
To set up the system time/date information
To set up the advanced BIOS features
Advanced
H/W Monitor To display current hardware status
Boot
To set up the default system device to locate and load the
Operating System
Security
Exit
To set up the security features
To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
3 1
3.1.2
N
a
v
i
g
a
t
i
o
n
K
e
y
s
Please check the following table for the function description of each navigation
key.
Navigation Key(s)
Function Description
/
/
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
+ / -
<Enter>
<F1>
<F9>
<F10>
<ESC>
To display the General Help Screen
To load optimal default values for all the settings
To save changes and exit the BIOS SETUP UTILITY
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the BIOS SETUP UTILITY, the Main screen will appear and display
the system overview.
BIOS SETUP UTILITY
Advanced
H/W Monitor
Boot
Security
Exit
Main
System Overview
Use [Enter], [TAB]
or [SHIFT-TAB] to
select field.
System Time
System Date
[17:00:09]
[Wed 07/09/2008]
NF6-GLAN BIOS P1.00
AMD Athlon(tm) 64 X2 Dual Core
Processor 5000+ (64bit)
2600 MHz
a
Use [+] or [-] to
configure system Time.
BIOS Version
Processor Type
:
:
Processor Speed
:
Microcode Update : 60FB2/0
:
L1 Cache Size
L2 Cache Size
256KB
1024KB
Select Screen
Select Item
:
+-
Tab
F1
F9
F10
ESC
Change Field
Select Field
General Help
Load Defaults
Save and Exit
Exit
Total Memory
: 512MB with 64MB shared memory
Dual-Channel Memory Mode
: 256MB/266MHz (DDRII533)
: 256MB/266MHz (DDRII533)
DDRII
DDRII
1
2
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
System Time [Hour:Minute:Second]
Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
3 2
3.3
A
d
v
a
n
c
e
d
S
c
r
e
e
n
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP
Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.
BIOS SETUP UTILITY
H/W Monitor
Boot
Security
Exit
Main
Advanced
Options for CPU
Advanced Settings
WARNING : Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
IDE Configuration
PCIPnP Configuration
Floppy Configuration
SuperIO Configuration
USB Configuration
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
General Help
Load Defaults
Save and Exit
Exit
F10
ESC
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
3.3.1 CPU Configuration
BIOS SETUP UTILITY
Advanced
CPU Configuration
If AUTO, multiplier and
voltage will be left at the
rated frequency/voltage. If
Manual, multiplier and
voltage will be set based
on User Selection in Setup.
[Disabled]
AM2 Boost
[Auto]
Overclock Mode
[200]
[100]
CPU Frequency (MHz)
PCIE Frequency (MHz)
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
CPU/LDT Spread Spectrum
PCIE Spread Spectrum
SATA Spread Spectrum
Boot Failure Guard
Cool' n' Quiet
Secure Virtual Machine
Enhanced Halt State
[Enabled]
[Disabled]
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
Processor Maximum Frequency
Processor Maximum Voltage
Multiplier/Voltage Change
x25.0 5000 MHz
F1
F9
F10
1.350
[Auto]
V
[Auto]
[Disabled]
Memory Clock
Flexibility Option
ESC Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
AM2 Boost
This option appears only when you adopt AM2 CPU. If you set this option to
[Enabled], you will enable ASRock AM2 Boost function, which will improve
the memory performance. The default value is [Disabled]. Please refer to
caution 11 on page 9 for details.
3 3
Overclock Mode
Use this to select Overclock Mode. The default value is [Auto]. Configura-
tion options: [Auto], [CPU, PCIE, Sync.] and [CPU, PCIE, Async.].
CPU Frequency (MHz)
Use this option to adjust CPU frequency.
PCIE Frequency (MHz)
Use this option to adjust PCIE frequency.
CPU/LDT Spread Spectrum
This feature will be set to [Enabled] as default. Configuration
options: [Disabled] and [Enabled].
PCIE Spread Spectrum
This feature will be set to [Enabled] as default. Configuration
options: [Disabled] and [Enabled].
SATA Spread Spectrum
This feature will be set to [Enabled] as default. Configuration
options: [Disabled] and [Enabled].
Boot Failure Guard
Enable or disable the feature of Boot Failure Guard.
Cool ‘n’ Quiet
Use this item to enable or disable AMD’s Cool ‘n’ QuietTM technology. The
default value is [Auto]. Configuration options: [Auto], [Enabled] and
[Disabled]. If you install Windows® VistaTM and want to enable this function,
please set this item to [Enabled]. Please note that enabling this function may
reduce CPU voltage and memory frequency, and lead to system stability or
compatibility issue with some memory modules or power supplies. Please
set this item to [Disable] if above issue occurs.
Secure Virtual Machine
This option appears only when you adopt AM2 CPU. When this option is set
to [Enabled], a VMM (Virtual Machine Architecture) can utilize the additional
hardware capabilities provided by AMD-V. The default value is [Enabled].
Configuration options: [Enabled] and [Disabled].
Enhance Halt State
All processors support the Halt State (C1). The C1 state is supported
through the native processor instructions HLT and MWAIT and requires no
hardware support from the chipset. In the C1 power state, the processor
maintains the context of the system caches.
Processor Maximum Frequency
It will display Processor Maximum Frequency for reference.
North Bridge Maximum Frequency
This option appears only when you adopt Phenom CPU. It will display North
Bridge Maximum Frequency for reference.
3 4
Processor Maximum Voltage
It will display Processor Maximum Voltage for reference.
Multiplier/Voltage Change
This item is set to [Auto] by default. If it is set to [Manual], you may adjust the
value of Processor Frequency and Processor Voltage. However, it is rec-
ommended to keep the default value for system stability.
BIOS SETUP UTILITY
Advanced
CPU Configuration
If AUTO, multiplier and
voltage will be left at the
rated frequency/voltage. If
Manual, multiplier and
voltage will be set based
on User Selection in Setup.
[Disabled]
AM2 Boost
[Auto]
Overclock Mode
[200]
[100]
CPU Frequency (MHz)
PCIE Frequency (MHz)
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
CPU/LDT Spread Spectrum
PCIE Spread Spectrum
SATA Spread Spectrum
Boot Failure Guard
Cool' n' Quiet
Secure Virtual Machine
Enhanced Halt State
[Enabled]
[Disabled]
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
Processor Maximum Frequency
Processor Maximum Voltage
Multiplier/Voltage Change
Processor Frequency
x25.0 5000 MHz
1.350
[Manual]
[x8]
[1.500V]
F1
F9
F10
V
ESC Exit
Processor Voltage
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Processor Frequency
This option appears only when you adopt AM2 CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for system stability, it is not recommended to ad-
just the value of this item.
Processor Voltage
This option appears only when you adopt AM2 CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for safety and system stability, it is not recom-
mended to adjust the value of this item.
Processor Target Frequency
This option appears only when you adopt Phenom CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for system stability, it is not recommended to ad-
just the value of this item.
North Bridge Target Frequency
This option appears only when you adopt Phenom CPU. This item will show
when “Multiplier/Voltage Change” is set to [Manual]; otherwise, it will be
hidden. The range of the value depends on the CPU you adopt on this
motherboard. However, for safety and system stability, it is not recom-
mended to adjust the value of this item.
3 5
CPU Frequency Multiplier
This option appears only when you adopt Phenom CPU. However, for
safety and system stability, it is not recommended to adjust the value of this
item.
CPU Frequency Divider
This option appears only when you adopt Phenom CPU. However, for
safety and system stability, it is not recommended to adjust the value of this
item.
CPU Voltage
This option appears only when you adopt Phenom CPU. It allows you to
adjust the value of CPU voltage. However, for safety and system stability,
it is not recommended to adjust the value of this item.
NB Frequency Multiplier
This option appears only when you adopt Phenom CPU. However, for
safety and system stability, it is not recommended to adjust the value of this
item.
NB Voltage
This option appears only when you adopt Phenom CPU. It allows you to
adjust the value of NB voltage. However, for safety and system stability, it
is not recommended to adjust the value of this item.
Memory Clock
This item can be set by the code using [Auto]. You can set one of the
standard values as listed: [200 MHz (DDR2 400)], [266 MHz (DDR2 533)],
[333 MHz (DDR2 667)] and [400MHz (DDR2 800)]. If you adopt Phenom
CPU, there is one more option: [533MHz (DDR2 1066)].
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
Memory Controller Mode
This option appears only when you adopt Phenom CPU. It allows you to
adjust the memory controller mode. Configuration options: [Unganged] and
[Ganged]. The default value is [Unganged].
CAS Latency (CL)
Use this item to adjust the means of memory accessing. Configuration
options: [Auto], [3CLK], [4CLK], [5CLK], [6CLK] and [7CLK]. The default
value is [Auto].
TRCD
Use this to adjust TRCD values. Configuration options: [Auto], [3CLK], [4CLK],
[5CLK] and [6CLK]. The default value is [Auto].
TRP
Use this to adjust TRP values. Configuration options: [Auto], [3CLK], [4CLK],
[5CLK] and [6CLK]. The default value is [Auto].
3 6
TRTP
Use this to adjust TRTP values. Configuration options: [Auto], [2-4CLK] and
[3-5CLK]. The default value is [Auto].
TRAS
Use this to adjust TRAS values. Configuration options: [Auto], [5CLK] to
[18CLK]. The default value is [Auto].
TRRD
Use this to adjust TRRD values. Configuration options: [Auto], [2CLK], [3CLK],
[4CLK] and [5CLK]. The default value is [Auto].
TRC
Use this to adjust TRC values. Configuration options: [11CLK] to [26CLK].
The default value is [Auto].
TWR
Use this to adjust TWR values. Configuration options: [Auto], [3CLK], [4CLK],
[5CLK] and [6CLK]. The default value is [Auto].
TWTR
Use this to adjust TWTR values. Configuration options: [Auto], [1CLK],
[2CLK] and [3CLK]. The default value is [Auto].
Addr/Cmd Fine Delay
Use this to adjust values for Addr/Cmd Fine Delay feature. Configuration
options: [Auto], [No Delay], [1/64CLK] to [31/64CLK]. The default value is
[Auto].
CS/ODT Fine Delay
Use this to adjust values for CS/ODT Fine Delay feature. Configuration
options: [Auto], [No Delay], [1/64CLK] to [31/64CLK]. The default value is
[Auto].
MA Timing
Use this to adjust values for MA timing. Configuration options: [Auto], [2T],
[1T]. The default value is [Auto].
Bank Interleaving
Interleaving allows memory accesses to be spread out over banks on the
same node, or accross nodes, decreasing access contention.
3 7
3.3.2
C
h
i
p
s
e
t
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
Chipset Settings
To set DRAM Voltage.
Onboard LAN
Onboard HD Audio
Front Panel
[Enabled]
[Auto]
[Auto]
[PCI]
Primary Graphics Adapter
CPU-NB Link Speed
CPU-NB Link Width
[Auto]
[Auto]
[Auto]
[Auto]
DRAM Voltage
Chipset Core Voltage
Select Screen
Select Item
+ -
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard LAN
This allows you to enable or disable the onboard LAN feature.
OnBoard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If
you select [Auto], the onboard HD Audio will be disabled when PCI Sound
Card is plugged.
Front Panel
Select [Auto], [Enabled] or [Disabled] for the onboard HDAudio Front Panel.
Primary Graphics Adapter
This item will switch the PCI Bus scanning order while searching for video
card. It allows you to select the type of Primary VGA in case of multiple
video controllers. The default value of this feature is [PCI]. Configuration
options: [PCI] and [PCI Express].
CPU - NB Link Speed
This feature allows you selecting CPU to NB link frequency. Configuration
options: [Auto], [200 MHz], [400 MHz], [600 MHz], [800 MHz] and [1000 MHz].
CPU - NB Link Width
This feature allows you selecting CPU to NB link width. Configuration options:
[Auto], [8 Bit] and [16 Bit].
DRAM Voltage
Use this to select DRAM voltage. Configuration options: [Auto], [1.80V],
[1.85V], [1.90V], [1.95V], [2.00V], [2.05V], [2.15V], [2.20V], [2.30V],
[2.35V], [2.40V], [2.45V], [2.55V], [2.60V], [2.65V] and [2.70V]. The default
value is [Auto].
Chipset Voltage
Use this to select chipset voltage. Configuration options: [Auto], [1.24V],
[1.30V], [1.37V] and [1.42V]. The default value is [Auto].
3 8
3.3.3
A
C
P
I
C
o
n
f
i
g
u
r
a
t
i
o
n
BIOS SETUP UTILITY
Advanced
ACPI Settings
Select auto-detect or
disable the STR
feature.
[Auto]
[No]
[Disabled]
Suspend To RAM
Repost Video on STR Resume
Away Mode Support
Restore on AC / Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Select Screen
Select Item
ACPI HPET Table
OSC Control
[Disabled]
[Auto]
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Suspend to RAM
Use this item to select whether to auto-detect or disable the Suspend-to-
RAM feature. Select [Auto] will enable this feature if the OS supports it. If
you set this item to [Disabled], the function “Repost Video on STR Resume”
will be hidden.
Repost Video on STR Resume
This feature allows you to repost video on STR resume. (STR refers to
suspend to RAM.)
Away Mode Support
Use this item to enable or disable Away Mode support under Windows® XP
Media Center OS. The default value is [Disabled].
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power
loss. If [Power Off] is selected, the AC/power remains off when the
power recovers. If [Power On] is selected, the AC/power resumes
and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from
the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
3 9
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Disabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® VistaTM certification.
OSC Control
Use this option to adjust OSC control. The default value is [Auto]. Configu-
ration options: [Auto], [Enabled] and [Disabled].
3.3.4 IDE Configuration
BIOS SETUP UTILITY
Advanced
ENABLED: enables the
integrated IDE
Controller.
IDE Configuration
DISABLED: disables the
integrated IDE
Controller.
[Enabled]
[Enabled]
[non-RAID]
OnBoard IDE Controller
OnBoard SATA Controller
SATA Operation Mode
IDE Master
IDE Slave
[Hard Disk]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
[Not Detected]
SATAII
SATAII
SATAII
SATAII
1
2
3
4
Select Screen
Select Item
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard IDE Controller
Use this item to enable or disable the “OnBoard IDE Controller” feature.
OnBoard SATA Controller
Use this item to enable or disable the “OnBoard SATA Controller” feature.
SATA Operation Mode
Use this item to adjust SATA Operation Mode. The default value of this
option is [non-RAID]. If you want to operate RAID function on SATA / SATAII
HDDs, please select [RAID].
* If you select [RAID] mode, SATA / SATAII HDDs can not be accessed until you finish
configuring RAID functions in NVIDIA BIOS / Windows RAID Utility.
IDE Device Configuration
You may set the IDE configuration for the device that you specify. We will
use the “IDE Master” as the example in the following instruction, which can
be applied to the configurations of “IDE Slave” as well.
4 0
BIOS SETUP UTILITY
Advanced
IDE Master
Select the type
of device connected
to the system.
Device
Vendor
Size
:Hard Disk
:MAXTOR 6L080J4
:80.0 GB
:Supported
LBA Mode
Block Mode :16Sectors
PIO Mode :4
Async DMA :MultiWord DMA-2
Ultra DMA :Ultra DMA-6
S.M.A.R.T.
:Supported
Type
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Disabled]
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S . M . A . R . T .
32Bit Data Transfer
+-
F1
F9
F10
ESC Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read data
from the hard disk. Make sure to set the partition of the Primary
IDE hard disk drives to active.
[CD/DVD]:This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for
compatible IDE devices.
4 1
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY
Advanced
Value in units of PCI
Advanced PCI / PnP Settings
clocks for PCI device
latency timer
register.
PCI Latency Timer
PCI IDE BusMaster
[32]
[Enabled]
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
F1
F9
F10
ESC Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
PCI Latency Timer
The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
4 2
3.3.6
F
l
o
p
p
y
C
o
n
f
i
g
u
r
a
t
i
o
n
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY
Advanced
Floppy Configuration
Floppy
Select the type of
floppy drive
connected to the
system.
[1.44 MB 31 "]
A
2
Select Screen
Select Item
+-
Change Option
General Help
Load Defaults
Save and Exit
F1
F9
F10
ESC Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
3.3.7 Super IO Configuration
BIOS SETUP UTILITY
Advanced
Configure Super IO Chipset
Allow BIOS to Enable
or Disable Floppy
Controller.
[Enabled]
[3F8 / IRQ4]
[Disabled]
[378]
[ECP + EPP]
[1.9]
OnBoard Floppy Controller
Serial Port Address
Infrared Port Address
Parallel Port Address
Parallel Port Mode
EPP Version
ECP Mode DMA Channel
Parallel Port IRQ
[DMA3]
[IRQ7]
Select Screen
Select Item
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard Floppy Controller
Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Infrared Port Address
Use this item to set the address for the onboard infrared port or disable it.
Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].
4 3
Parallel Port Address
Use this item to set the address for the onboard parallel port or disable it.
Configuration options: [Disabled], [378], and [278].
Parallel Port Mode
Use this item to set the operation mode of the parallel port. The default
value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP
version in the following item, “EPP Version”. Configuration options:
[Normal], [Bi-Directional], and [ECP+EPP].
EPP Version
Use this item to set the EPP version. Configuration options: [1.9]
and [1.7].
ECP Mode DMA Channel
Use this item to set the ECP mode DMA channel. Configuration
options: [DMA0], [DMA1], and [DMA3].
Parallel Port IRQ
Use this item to set the IRQ for the parallel port. Configuration options:
[IRQ5] and [IRQ7].
3.3.8 USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration
To enable or disable
the onboard USB
controllers.
[Enabled]
USB Controller
USB 2.0 Support
Legacy USB Support
[Enabled]
[BIOS Setup Only]
Select Screen
Select Item
+-
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this option to select legacy support for USB devices. There are four
configuration options: [Enabled], [Auto], [Disabled] and [BIOS Setup
Only]. The default value is [BIOS Setup Only]. Please refer to below
descriptions for the details of these four options:
4 4
[Enabled] - Enables support for legacy USB.
[Auto] - Enables legacy support if USB devices are connected.
[Disabled] - USB devices are not allowed to use under legacy OS and
BIOS setup when [Disabled] is selected. If you have USB compatibility
issue, it is recommended to select [Disabled] to enter OS.
[BIOS Setup Only] - USB devices are allowed to use only under BIOS
setup and Windows / Linux OS.
3.4
H
a
r
d
w
a
r
e
H
e
a
l
t
h
E
v
e
n
t
M
o
n
i
t
o
r
i
n
g
S
c
r
e
e
n
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
BIOS SETUP UTILITY
Boot
Security
Exit
Main
Advanced
H/W Monitor
Hardware Health Event Monitoring
CPU Temperature
M / B Temperature
:
:
37 C / 98 F
31 C / 87 F
CPU Fan Speed
Chassis Fan Speed
:
:
2833 RPM
N / A
Vcore
:
:
:
:
1.532 V
3.129 V
4.877 V
11.741 V
+
+
+
3.30V
5.00V
12.00V
Select Screen
Select Item
General Help
Load Defaults
Save and Exit
Exit
F1
F9
F10
ESC
CPU Quiet Fan
[Disabled]
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
CPU Quiet Fan
This item allows you to control the CPU fan speed and fan noise. If you set
this option as [Disabled], the CPU fan will operate in full speed. If you set
this option as [Enabled], you will find the items “Target CPU Temperature”
and “Target Fan Speed” appear to allow you adjusting them. The default
value is [Disabled]. You are allowed to enable this function only when you
install 4-pin CPU fan.
Target CPU Temperature
The target temperature will be between 45 C/113 F and 65 C/149 F.
The default value is [50 C/122 F].
Target Fan Speed
Use this option to set the target fan speed. You can freely adjust the
target fan speed according to the target CPU temperature that you
choose. The default value is [Fast]. Configuration options: [Fast], [Middle]
and [Slow].
4 5
3.5
B
o
o
t
S
c
r
e
e
n
In this section, it will display the available devices on your system for you to config-
ure the boot settings and the boot priority.
BIOS SETUP UTILITY
Main
Advanced
H/W Monitor
Boot
Security
Exit
Boot Settings
Configure Settings
during System Boot.
Boot Settings Configuration
[1st Floppy Device]
1st Boot Device
2nd Boot Device
3rd Boot Device
4th Boot Device
Hard Disk Drives
Removable Drives
CD/DVD Drives
[HDD: PM - HDS722580VL]
[CD / DVD: 3S - CD - ROM C]
[USB]
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
F10
ESC
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
3.5.1 Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
To enable or disable the
boot from onboard LAN
feature.
Boot From Onboard LAN
Bootup Num-Lock
[Disabled]
[On]
Select Screen
Select Item
+ -
F1
F9
F10
ESC
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Boot Onboard LAN
Use this item to enable or disable the Boot Onboard LAN feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
4 6
3.6
S
e
c
u
r
i
t
y
S
c
r
e
e
n
In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.
BIOS SETUP UTILITY
Main
Advanced
H/W Monitor
Boot
Security
Exit
Security Settings
Install or Change the
password.
Supervisor Password : Not Installed
User Password : Not Installed
Change Supervisor Password
Change User Password
Select Screen
Select Item
Enter Change
F1
F9
F10
ESC
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
4 7
3.7
E
x
i
t
S
c
r
e
e
n
BIOS SETUP UTILITY
H/W Monitro Boot
Main
Advanced
Security
Exit
Exit Options
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Select Screen
Select Item
Enter Go to Sub Screen
F1
F9
F10
General Help
Load Defaults
Save and Exit
ESC Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Dis-
card changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Dis-
card changes?” Select [OK] to discard all changes.
Load Optimal Defaults
When you select this option, it will pop-out the following message, “Load
optimal defaults?” Select [OK] to load the default values for all the setup
configurations.
4 8
4. Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems:
2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit. Because motherboard
settings and hardware options vary, use the setup procedures in this chapter for
general reference only. Refer to your OS documentation for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the file
“ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects the
installed devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard supports.
Click on a specific item then follow the installation wizard to install it.
4.2.4 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome
dealer for further information.
4 9
|