AOC Computer Monitor 916SWA User Manual

916Swa User Manual

1. Preface

About This Guide

This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to change without notice.

The sections are as follows:

•

Safety Instructions: lists safety information.

Setup: describes the initial setup process.

Using the Monitor: gives an overview of how to use the monitor.

Drivers: provides driver installation instructions for Windows.

Technical Support : provides tips and solutions for common problems.

Product Information: lists the technical specifications of the monitor.

Warranty Statement: Warranty Statement used in Europe.

National Conventions

The following subsections describe notational conventions used in this document.

Notes, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are

used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your computer system.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.

Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory

authority.

Product Registration

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR

MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.

Precautions

WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards,

and/or mechanical hazards.

Read and follow these precautions when connecting and using your computer monitor:

PRECAUTIONS

•

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart

or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer

and follow the kit instructions.

•

Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating,

be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a

radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

•

The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult

your dealer or local power company.

The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety

feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do

not defeat the safety purpose of the grounded plug.

•

Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.

Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to

qualified service personnel.

•

To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between 100 - 240V AC,

Min. 5A.

•

The wall socket shall be installed near the equipment and shall be easily accessible.

For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license(Only for monitors with power adapter).

3. Setup

Setup the stand and base

Please setup or remove the base following below steps.

Adjusting Viewing Angle

•

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.

Hold the stand so you do not topple the monitor when you change the monitor's angle.

You are able to adjust the monitor's angle from -5°to 20°.

NOTE:

Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.

Attaching the Cables

Cable Connections On Back of Monitor and Computer

1.Power

2.Analog

3. audio

Turn off your computer before performing the procedure below.

1. Connect the power cable to the AC port on the back of the monitor.

2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port.

3. Turn on your monitor and computer.

If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting.

Attaching Wall Mounting Arm

Preparing to Install An Optional Wall Mounting Arm

4. Using the Monitor

Setting the Optimal Resolution

The recommended resolution for this monitor is 1440 by 900. To setup the monitor to this resolution, follow the steps below.

1. Click START.

2. Click SETTINGS.

3. Click CONTROL PANEL.

4. Double click DISPLAY.

5. Click SETTINGS.

6. Set the resolution SLIDE-BAR to 1440 by 900.

External Controls

Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture

can be adjusted to your personal preferences.

* The power cord should be connected.

* Press the power button to turn on the monitor. The power indicator will light up.

1. Auto Config

2. Volume / -

3. Volume / +

4. Menu / Enter

5. Power Button & Indicator

OSD Settings

•

Press the MENU-button to activate the OSD window.

Press+ or - to navigate through the functions. Once the desired function is highlighted, press the MENU-buttonto activate it.If the function selected has a sub-menu,

press or again to navigate through the sub-menu functions.Once the desired function is highlighted, press MENU-button to activate it.

•

Press+ or - to change the settings of the selected function. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-3.

OSD Lock Function: To lock the OSD, press and hold the MENUbutton while the monitor is off and then press power button to turn the monitor on. To un-lock the

OSD - press and hold the MENUbutton while the monitor is off and then press power button to turn the monitor on.

•

Press Exit key continually for 7 sec. to turn on or off DDC-CI.

DCB Adjustment

What is DCB?

Dynamic Color Boost (DCB) is an advanced color adjustment technology. Through analyzing RGB signals, DCB creates more vivid and natural images to suit various color

environment needs. DCB has two types of color enhancers: “Color Boost” and “Picture Boost” .

DDC: Dynamic color control

ICM: Intelligent color management

1) How to use Color Boost?

YCM adjustment: In addition to the basic R (red), G (green), B (blue) color adjustments, Color Boost has added Y (yellow), B (blue), and M (magenta) for more color fine-

tuning options. YCM adjustments are in the third icon labeled "Color Temperature "in the OSD menu. When adjusting YCM values, RBG values will also be changed

automatically due to the color correlation between RGB and YCM.

Five color-enhancement settings: To accommodate various display needs, Color Boost also offers 5 different color enhancement modes: Full Enhance, Natural Skin,

Green Field, Sky Blue, and Auto-Detect. Please go to the fourth icon labeled “Color Boost” in the OSD menu and select one of the five settings you desire to be turned on.

Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all colors become more vibrant.

Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents human skin with more natural and truer colors.

"Natural Skin" setting is ideal for viewing human portrait and detailed skin texture.

Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain landscape would look more natural and fresh. “Green Field”

setting is ideal for watching mountain scenery and outdoor sports.

Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will look more vivid and in-depth. "Sky Blue" setting is ideal

for viewing sky and ocean images.

Auto Detect: When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively picture.

Demo: Screen divided into two for demonstration purposes.

2) How to use Picture Boost?

Users can change the color settings of a self-selected zone on the screen. The size and position of the selected zone can also be adjusted. "Picture Boost" is located in the

fifth icon labeled "Picture Boost" in the OSD menu. Turn on "Bright Frame" to select a zone on the screen to be enhanced. Please note when adjust or turn on any one of

the DCB features, the rest of color settings including DCR will be disabled or return to default.

Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations.

DCR Adjustment

What is DCR?

Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in more depths. By increasing the

darkness of the dark areas and the brightness of the bright areas, contrast ratio is uplifted to exceed 2000:1. DCR value varies subject to the original CR values of the LCD

module. The higher the original CR, the higher DCR can be achieved. DCR is great for watching movie or video contents.

How to Use DCR?

Go to the first OSD icon labeled "Luminance", turn on or off DCR as desires. DCR boosts the contrasts between lightness & darkness and enables the viewer to see more

layers and details of the picture, especially in the darker areas. Please note when DCR is on, DCB will be disabled.

DCR Demos:

Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than the above illustrations.

Function Control Illustration

Luminance

Brightness

Contrast

Adjust Range

0-100

Description

Backlight Adjustment

Contrast from Digital-register.

Standard Mode

0-100

Standard

Text

Eco mode

Text Mode

Internet

Game

Internet Mode

Game Mode

Movie

Movie Mode

Sports

Gamma1

Gamma2

Gamma3

Off

Sports Mode

Adjust to Gamma1

Adjust to Gamma 2

Adjust to Gamma 3

Disable dynamic contrast ratio

Enable dynamic contrast ratio

Gamma

DCR

Image Setup

Clock

0-100

Adjust picture Clock to reduce Vertical-Line noise.

Adjust Picture Phase to reduce Horizontal-Line noise

Adjust the verticalposition of the picture.

Focus

H.Position

V.Position

Color Temp.

Warm

Adjust the horizontal position of the picture.

Recall Warm Color Temperature from EEPROM.

Recall Normal Color Temperature from EEPROM.

Recall Cool Color Temperature from EEPROM.

Recall SRGB Color Temperature from EEPROM.

Blue Gain from Digital-register

Normal

Cool

sRGB

User

User-B

User-G

User-R

User-Y

User-C

User-M

Green Gain Digital-register.

Red Gain from Digital-register

Yellow Gain from Digital-register

Cyan Gain from Digital-register

Magenta Gain from Digital-register

Color Boost

Full Enhance

Nature Skin

Green Field

Sky-blue

on or off

Disable or Enable Full Enhance Mode

Disable or Enable Nature Skin Mode

Disable or Enable Green Field Mode

Disable or Enable Sky-blue Mode

Disable or Enable AutoDetect Mode

Disable or Enable Demo

AutoDetect

Demo

Picture Boost

Frame Size

Brightness

Contrast

0-14

Adjust Frame Size

0-100

Adjust Frame Brightness

Adjust Frame Contrast

Adjust Frame Hue

Hue

Saturation

Adjust Frame Saturation

H. position

V.position

on or off

Adjust Frame horizontal Position

Adjust Frame vertical Position

Disable or Enable Bright Frame

Position

Bright Frame

OSD Setup

H.Position

V.Position

Timeout

0-100

Adjust the verticalposition of OSD

Adjust the horizontal position of OSD

Adjust the OSD Timeout

Language

Extra

Select the OSD language

Auto Config

yes or no

Auto adjust the picture to default

Reset

Reset the menu to default

EXIT/DDC-CI

Information

Turn ON/OFF DDC-CI Support

Show the information of the main image and sub-image source

LED Indicators

Status

LED Color

Full Power Mode

Active-off Mode

Green

Orange

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:

1. Remove the base.

2. Follow the manufacturer's instructions to assemble the wall mounting arm.

3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.

4. Insert the 4 screws into the holes and tighten.

5. Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall.

5. Drivers

Windows 2000

1. Start Windows® 2000

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select 'Monitor'

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.

- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.

6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.

7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk...'.

8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).

9. Click on the 'Open' button, then click on the 'OK' button.

10. Select your monitor model and click on the 'Next' button.

11. Click on the 'Finish' button then the 'Close' button.

If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.

Windows ME

1. Start Windows® Me

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select the 'Monitor' button, then click on 'Change...' button.

6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.

7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'.

8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.

9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.

10. Click on 'Finish' button then the 'Close' button.

Windows XP

1. Start Windows® XP

2. Click on the 'Start' button and then click on 'Control Panel'.

3. Select and click on the category 'Printers and Other Hardware'

4. Click on the 'Display' Item.

5. Select the 'Settings' tab then click on the 'Advanced' button.

6. Select 'Monitor' tab

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.

- If the 'Properties' button is active, click on 'Properties' button.

Please follow the steps below.

7. Click on the 'Driver' tab and then click on 'Update Driver...' button.

8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.

9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.

10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F: (CD-ROM Drive).

11. Click on the 'Open' button, then click the 'OK' button.

12. Select your monitor model and click on the 'Next' button.

- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message, please click on the 'Continue Anyway' button.

13. Click on the 'Finish' button then the 'Close' button.

14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.

Windows Vista

1. Start Windows® Vista

2. Click the Start button; select and click on 'Control Panel'.

3. Select and click on 'Hardware and Sound'

4. Choose 'Device Manager' and Click on 'Update device drivers'.

5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.

6. Click on 'Update Driver Software'.

7. Select 'Browse my computer for driver software'.

8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:(CD-ROM Drive:\\Lcd\PC\drivers\).

9. Click the 'Next' button.

10. Wait few minutes for installing the driver, and then click 'Close' button.

6. Technical Support

Frequently Asked Questions

Problem & Question

Power LED Is Not ON

Possible Solutions

•

Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet

and to the monitor.

•

In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer

& video card. Check with your computer manufacturer. Also check the monitor's video cable and make

sure none of the pins are bent.

Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at :

http://www.aoc.com)

No Plug & Play

•

Adjust the Contrast and Brightness Controls.

Make sure you are not using an extension cable or switch box. We recommend plugging the monitor

directly to the video card output connector on the back of your computer.

Picture Is Fuzzy & Has Ghosting Shadowing

Problem

•

Move electrical devices that may cause electrical interference as far away from the monitor as possible.

Use the maximum refresh rate your monitor is capable of at the resolution your are using.

Picture Bounces, Flickers Or Wave Pattern Is

Present In The Picture

•

The Computer Power Switch should be in the ON position.

The Computer Video Card should be snugly seated in its slot.

Make sure the monitor's video cable is properly connected to the computer.

Inspect the monitor's video cable and make sure none of the pins are bent.

Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing

the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.

Monitor Is Stuck In Active Off-Mode"

•

Inspect the monitor's video cable and make sure that none of the pins arebent.

Make sure the monitor's video cable is properly connected to the computer.

Missing one of the primary colors (RED,

GREEN, or BLUE)

•

Adjust H-Position and V-Position or press hot-key (AUTO).

Screen image is not centered or sized

properly

Adjust RGB color or select color temperature

Picture has color defects (white does not

look white)

Use win 95/98 shut-down mode Adjust CLOCK and FOCUS or perform hot-key (AUTO-key )

Horizontal or vertical disturbances on the

screen

7. Product Information

Specifications

Model number

Driving system

Size

916Swa

TFT Color LCD

48.0cm ( 19" 16:10)

0.285mm(H) x 0.285mm(V)

R, G, B Analog lnterface

H/V TTL

Pixel pitch

LCD Panel

Video

Separate Sync.

Display Color

16.2 million Colors

135 MHz

Dot Clock

Horizontal scan range

31 kHz - 80 KHz

Horizontal scan

Size(Maximum)

410.4mm

Vertical scan range

55 Hz - 75 Hz

Vertical scan Size(Maximum)256.5mm

Optimal preset resolution

Highest preset resolution

Plug & Play

1440 x 900 (60 Hz)

Resolution

1440 x 900 (75 Hz)

VESA DDC2B/CI

Input Connector

D-Sub 15pin

Input Video Signal

Power Source

Analog: 0.7Vp-p(standard), 75 OHM, Positive

100~240VAC, 47~63Hz

Active < 37W

Standby < 2W

15-pin Mini D-Sub

Power Consumption

Connector Type

Signal Cable Type

Dimensions & Weight:

Height (with base)

Width

Detachable

362.9 mm

438.5 mm

209.86 mm

4.4 kg

Physical Characteristics

Depth

Weight (monitor only)

Weight (with packaging)

5.8 kg

Temperature:

Operating

0°to 50°

Non-Operating

Humidity:

-20°to 60°

Environmental

Operating

10% to 85% (non-condensing)

5% to 80% (non-condensing)

Non-Operating

Altitude:

Operating

0~ 3000m (0~ 10000 ft )

0~ 5000m (0~ 15000 ft )

Non-Operating

EPA Energy STAR ®

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this product meets the ENERGY

STAR® guidelines for energy efficiency.

Preset Display Modes

HORIZONTAL

VERTICAL

STAND

RESOLUTION

FREQUENCY(kHZ)

FREQUENCY(Hz)

640 X 480

832 X 624

1152 X 870

640 X 350

720 X 400

640 X 480

800 X 600

1024 X 768

1152 X 864

1024 X 768

35.0kHz

66.7Hz

VGA

49.7kHz

68.7kHz

31.5kHz

37.9kHz

37.5kHz

35.2kHz

37.9kHz

48.1kHz

46.9kHz

48.4kHz

56.5kHz

60.0kHz

67.5kHz

57.7kHz

74.5Hz

75.0Hz

70.1Hz

60.0Hz

72.8Hz

75.0Hz

56.3Hz

60.3Hz

72.2Hz

75.0Hz

60.0Hz

70.1Hz

75.0Hz

72.0Hz

VGA

SVGA

Dos-mode

VGA

SVGA

XGA

Normal

Special

XGA

1024 X 768

1280 X 1024

1440 X 900

60.023kHz

64.0kHz

74.4kHz

77.9kHz

80.0kHz

55.5kHz

70.6kHz

75.0Hz

60.0Hz

70.0Hz

72.0Hz

75.0Hz

60.0Hz

75.0Hz

SXGA

WXGA

Pin Assignments

Pin Number

15-Pin Side of the Signal Cable

Video-Red

Video-Green

Video-Blue

N.C.

Detect Cable

GND-R

GND-G

GND-B

+5V

Ground

N.C.

DDC-Serial data

H-sync

V-sync

DDC-Serial clock

Plug and Play

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and,

depending on the level of DDC used, communicate additional information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.

8. Warranty Statement

Warranty Statement

LIMITED THREE-YEAR WARRANTY*

AOC Color Monitors sold within Europe

AOC International (Europe) GmbH warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the

original date of consumer purchase. During this period, AOC International (Europe) GmbH will, at its option, either repair the defective product with new or

rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. The defective products that are replaced become the property

of AOC International (Europe) GmbH.

If the product appears to be defective, please contact your local dealer or refer to the warranty card when attached to the product.

Deliver the product freight pre-paid, along with the dated proof of purchase, to the AOC Authorized Service Center. If you cannot deliver the product in

person:

•

Pack it in its original shipping container (or equivalent)

Put the RMA number on the address label

Put the RMA number on the shipping carton

Insure it (or assume the risk of loss/damage during shipment)

Pay all shipping charges

AOC International (Europe) GmbH is responsible neither for any damage or loss during inbound transport damage nor to inbound product that was not

properly packaged.

AOC International (Europe) GmbH will pay the return shipping charges within one of the countries specified within this warranty statement. AOC

International (Europe) GmbH is not responsible for any costs associated with the transportation of product across international borders. This includes the

international border within the European Union.

* This limited warranty does not cover any losses or damages that occur as a result of

•

Shipping or improper installation or maintenance

Misuse

Neglect

Any cause other than ordinary commercial or industrial application

Adjustment by non-authorized source

Repair, modification, or installation of options or parts by anyone other than an AOC Authorized Service Center

Improper environment

Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other irregularities

This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole

responsibility and liability for any such modification or alteration.

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE

OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD.

AOC INTERNATIONAL (EUROPE) GMBH OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED

HERE. AOC INTERNATIONAL (EUROPE) GMBH LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR

OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN

NO EVENT SHALL AOC INTERNATIONAL (EUROPE) GMBH BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR

EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS

LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO

COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.

HP Hewlett Packard Hewlett Packard Computer Monitor V185E User Manual
Fujitsu PDS6101W User Manual
Frigidaire LA04CT80425 1A User Manual
Electrolux E30GC74G User Manual
DCS RGS 486GL User Manual
Cisco Systems Convection Oven ASC 2E User Manual
British Telecommunications BT 101 User Manual
AT T SL80108 User Manual
Asus Computer Hardware P4V533 MX User Manual
Addonics Technologies Computer Drive MSCFASA User Manual