Before operating the monitor, please read this manual thoroughly. This
manual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
As an ENERGY STAR Partner our company has determined that this
product meets the ENERGY STAR guidelines for energy efficiency.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or
moisture. Dangerously high voltages are present inside the monitor. Do not
open the cabinet. Refer servicing to qualified personnel only.
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST
BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR
FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE
2
ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG.
3
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl,
kitchen sink, laundry tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power outlet
as a safety feature. If your outlet does not accommodate the three-wire
plug, have an electrician install the correct outlet, or use an adapter to
ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
Unplug the unit during a lightening storm or when it will not be used for
long period of time. This will protect the monitor from damage due to
power surges.
Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
Do not attempt to service the monitor by yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily
accessible.
For use only with the attached power adapter (Output 12Vdc) which have
UL, CSA listed license.
4
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
Due to the nature of the fluorescent light, the screen may flicker during
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
Due to the nature of the LCD screen, an afterimage of the previous
screen may remain after switching the image when the same image has
been displayed for a long time. The monitor will slowly recover from this.
BEFORE YOU OPERATE THE MONITOR
FEATURES
19” (48cm) Wide screen TFT Color LCD Monitor
Crisp, Clear Display for Windows
Recommened Resolutions: 1440 X 900@60Hz
EPA ENERGY STAR®
Dual Input (DVI + Analog)
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner's Manual
3. Power Cord
4. D-Sub Cable
5. DVI Cable
6. External Adapter
5
INSTALLATION INSTRUCTIONS
SWIVEL BASE
Install
Remove
Figure 1 Installing and Removing the Swivel Base
POWER CORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s External Adapter
input socket, and then plug the other end of External adapter to LCD
monitor’s DC-power-input. The AC-power cord may be connected to
either a wall power outlet or the power outlet socket on your PC,
depending on the type of power cord supplied with your LCD monitor.
NOTES
A certified power supply cord has to be used with this equipment. The
relevant national installation and/or equipment regulations shall be
considered. A certified power supply cord not lighter than ordinary polyvinyl
chloride flexible cord according to IEC 60227 (designation H05VV-F 3G
0.75mm2 or H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible
cord be of synthetic rubber according to IEC 60245 (designation H05RR-F
3G
0.75mm2) shall be used.
6
CONTROLS AND CONNECTORS
Connecting Cables
Turn off your computer before performing the procedure below.
1. Connect the power adapter dc cable to the DC-In port on the back of the
monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and
connect the other end to the computer’s D-Sub port.
3. Plug the power cable of your monitor into a nearby outlet. Plug the other
end of the power cord into the power adapter.
4. (Optional – Requires a video card with DVI port) - Connect one end of the
24-pin DVI cable to the back of the monitor and
connect the other end to the computer’s DVI port.
5. Turn on your monitor and computer. If you monitor diplays an image,
installation is complete. If not, refer to the FAQ (frequently asked
questions) section for troubleshooting.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 2 Connecting Cables
1. DC-Jack Power Cable
2. D-sub Cable
3. AC Power Cord
4. DVI Cable
7
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face of the
monitor, then adjust the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
You are able to adjust the monitor’s angle from -5 to 20.
Figure 3
NOTES
Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
Careful attention is required not to catch your fingers or hands when you
change the angle.
8
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control
buttons are located at front panel of the monitor (See Figure 4). By changing
these settings, the picture can be adjusted to your personal preferences.
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor position. The power
indicator will light up.
Figure 4
External Control Button
EXTERNAL CONTROLS
1. Power Key
2. LED
3. MENU/ENTER
5. Brightness Preset
4. Luminance
6. Auto Adjust Key/Exit
9
FRONT PANEL CONTROL
Power Button:
Press this button to switch ON/OFF of monitor’s power.
MENU / ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Brightness/ Contrast
Adjust OSD status.
Luminance :
Adjust contrast and brightness or function adjust.
*Only adjustable at “STD” mode (see Brightness Preset below)
Brightness Preset:
Switch between “STD”, “OFFICE” & “VIVID”.
Auto Adjust button / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu).
2. When OSD menu is in off status, press this button over 2 seconds to
activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock
and Focus.
Power Indicator:
Blue
Orange —
—
Power On mode.
Off mode.
OSD Lock Function: To lock the OSD, press and hold the MENU button
while the monitor is off and then press power button to turn the monitor
on. To un-lock the OSD - press and hold the MENU button while the monitor
is off and then press power button to turn the monitor on.
NOTES
Do not install the monitor in a location near heat sources such as
radiators or air ducts, or in a place subject to direct sunlight, or excessive
dust or mechanical vibration or shock.
Save the original shipping carton and packing materials, as they will
come in handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a
mild detergent solution. Never use strong solvents such as thinner,
benzene, or abrasive cleaners, since these will damage the cabinet. As a
safety precaution, always unplug the monitor before cleaning it.
10
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press
function is highlighted, press the MENU-button to activate it. If the
function selected has a sub-menu, press or again to navigate
or
to navigate through the functions. Once the desired
through the sub-menu functions. Once the desired function is highlighted,
press MENU-button to activate it.
3. Press
or
to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other
function, repeat steps 2-3.
Figure 5 The OSD Message
11
ADJUSTING THE PICTURE
The descriptions for function control LEDS
Main
Menu
Item
Main
Menu
Icon
Sub
Menu
Icon
Sub Menu
Item
Description
Contrast
Brightness
Focus
Contrast from Digital-register.
Backlight Adjustment
Luminance
Adjust Picture Phase to reduce
Horizontal-Line noise
Image
Setup
Adjust picture Clock to reduce
Vertical-Line noise.
Clock
Adjust the horizontal position of the
picture.
H. Position
V. Position
Image
Position
Adjust the verticalposition of the
picture.
Recall Warm Color Temperature
from EEPROM.
Warm
Cool
N/A
N/A
N/A
Recall Cool Color Temperature
from EEPROM.
Recall sRGB Temperature from
EEPROM.
sRGB
Color
Temp.
User / Red
Red Gain from Digital-register.
Green Gain Digital-register.
Blue Gain from Digital-register.
User /
Green
User / Blue
Select input signal from analog
source (D-Sub)
Select input signal from digital
source (DVI)
Analog
Digital
N/A
N/A
Input
Select
12
Main
Menu
Icon
Sub
Menu
Icon
Main
Menu Item
Sub Menu
Item
Description
Adjust the horizontal position of
the OSD.
H. Position
V. Position
OSD Setup
Adjust the verticalposition of the
OSD.
OSD
Timeout
Adjust the OSD timeout.
Language
Language
N/A Select the language you like.
Show the resolution,
H/V
Information
Information N/A frequency and input port of current
input timing.
Clear each old status of Auto-
configuration .
Yes
N/A
N/A
Reset
Exit
Do not execute reset, return to
main menu.
No
N/A
N/A Exit OSD
13
PLUG AND PLAY
Plug & Play DDC 2B Feature
This monitor is equipped with VESA DDC 2B capabilities according to the
VESA DDC STANDARD. It allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, communicate additional
information about its display capabilities.
The DDC 2B is a bidirectional data channel based on the I²C protocol. The
host can request EDID information over the DDC 2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO
OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to conserve electrical energy
by reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. The appearance is
similar to a "Screen Saver" feature except the display is completely off. The
display is restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet
plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage
rating for the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male
configuration. The other end terminates with a molded-on type connector
body, rated 10A, 250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
14
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
Possible Solution
*Check if the Power Switch is in the ON
position
*Power Cord should be connected
*Check if the PC system is Plug & Play
compatible
No Plug & Play
*Check if the Video Card is Plug & Play
compatible
*Check if the D-15 plug pin of Video
Cable is bent
*Adjust the Contrast and Brightness
Controls.
Picture is fuzzy
Picture bounces or a wave *Move electrical devices that may cause
pattern is present in the picture electrical interference.
The power LED is ON (orange) *Computer Power Switch should be in
but there’s no video or no the ON position.
picture.
*Computer Video Card should be snugly
seated in its slot.
*Make sure monitor’s video cable is
properly connected to the computer.
*Inspect monitor’s video cable and make
sure none of the pins are bent.
*Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary *Inspect the monitor’s video cable and
colors (RED, GREEN, or
BLUE)
make sure that none of the pins are
bent.
Screen image is not centered or *Adjust pixel frequency (CLOCK) and
sized properly.
Picture has color defects
(white does not look white)
FOCUS or press hot-key (AUTO).
*Adjust RGB color or select color
temperature.
Horizontal
or
vertical *Use win 95/98 shut-down mode Adjust
disturbances on the screen
CLOCK and FOCUS or perform hot-
key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the picture has not correct width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-
down mode pattern.
15
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected , If the connector is
loose, tighten the connector’s screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode ,set the computer to
display mode given in the following table.(see page 17)
16
APPENDIX
SPECIFICATIONS
Driving system TFT Color LCD
LCD Panel
Input
Size
48cm(19")
Pixel pitch
Video
0.285mm( H ) × 0.285mm( V )
R,G,B Analog Interface
Digital Interface
Separate Sync. H/V TTL
H-Frequency
V-Frequency
30kHz –83kHz
55-75Hz
Display Colors
Dot Clock
16.2M Colors
135MHz
Max. Resolution
1440 × 900 @60Hz
VESA DDC 2BTM
≤36W
Plug & Play
EPA ENERGY STAR®
ON Mode
OFF Mode
≤1W
Input Connector
15-pin D-Sub
DVI 24pin
Input Video Signal
Analog:0.7Vp-p(standard),
75 OHM, Positive
Digital signal
Maximum Screen Size
Power Source
Horizontal : 410mm
Vertical : 256mm
100~240VAC,47~63Hz
Operating Temp: 5° to 50°C
Storage Temp.: -20° to 60°C
Operating Humidity :
10% to 85%
Environmental
Considerations
Dimension
440×356×215 (W ×H×D)mm
4kg Unit (net)
Weight (N. W.)
17
Switch
Auto Adjust Key
Brightness Preset
Luminance
Power Button
MENU
External Controls:
Functions
Contrast
Brightness
Focus
Clock
H. Position
V. Position
(Warm)Color
(Cool)Color
sRGB
RGB Color temperature
Input select
OSD Setup
Language
Information
Reset
Exit
36 Watts
Power Consumption
( Maximum )
Regulatory Compliance
cULus, FCC, CE, TUV/S
18
Preset Display Modes
HORIZONTAL
FREQUENCY
VERTICAL
FREQUENCY
STANDARD
Dos-mode
RESOLUTION
720 × 400
640 × 480
31.47kHz
70.0Hz
60.0Hz
75.0Hz
60.0Hz
75.0Hz
60.0Hz
70.0Hz
75.0Hz
60.0Hz
75.0Hz
59.8Hz
31.47kHz
37.50kHz
VGA
640 × 480
800 × 600
37.879kHz
46.875kHz
48.363kHz
56.476kHz
60.021kHz
64.000kHz
80.000kHz
55.935kHz
SVGA
800 × 600
1024 × 768
1024 × 768
1024 × 768
1280 × 1024
1280 × 1024
1440 × 900
XGA
SXGA
WXGA+
19
CONNECTOR PIN ASSIGNMENT
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
+5V
Detect Cable
Ground
DDC-Serial Data
H-Sync
V-Sync
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
DDC-Serial Clock
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
TMDS Data 2-
TMDS Data 2+
TMDS Data 2/4
Shield
13.
14.
15.
TMDS Data 3+
+5V Power
Ground(for+5V)
4.
5.
6.
7.
TMDS Data 4-
TMDS Data 4+
DDC Clock
16.
17.
18.
19.
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5
Shield
DDC Data
8.
9.
10.
11.
N.C.
20.
21.
22.
23.
TMDS Data 5-
TMDS Data 5+
TMDS Clock Shield
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3
Shield
TMDS Clock +
TMDS Clock -
12.
TMDS Data 3-
24.
20
21
|