Yamaha CD Player CD S300BL User Manual

U
Compact Disc Player  
Lecteur Compact Disc  
OWNER’S MANUAL  
MODE D’EMPLOI  
IMPORTANT SAFETY INSTRUCTIONS  
FCC INFORMATION (for US customers)  
1
IMPORTANT NOTICE: DO NOT MODIFY THIS  
UNIT!  
Compliance with FCC regulations does not guarantee that  
interference will not occur in all installations. If this  
product is found to be the source of interference, which  
can be determined by turning the unit “OFF” and “ON”,  
please try to eliminate the problem by using one of the  
following measures:  
This product, when installed as indicated in the  
instructions contained in this manual, meets FCC  
requirements. Modifications not expressly approved by  
Yamaha may void your authority, granted by the FCC, to  
use the product.  
Relocate either this product or the device that is being  
affected by the interference.  
2
3
IMPORTANT: When connecting this product to  
accessories and/or another product use only high quality  
shielded cables. Cable/s supplied with this product  
MUST be used. Follow all installation instructions.  
Failure to follow instructions could void your FCC  
authorization to use this product in the USA.  
NOTE: This product has been tested and found to  
comply with the requirements listed in FCC Regulations,  
Part 15 for Class “B” digital devices. Compliance with  
these requirements provides a reasonable level of  
assurance that your use of this product in a residential  
environment will not result in harmful interference with  
other electronic devices.  
Utilize power outlets that are on different branch (circuit  
breaker or fuse) circuits or install AC line filter/s.  
In the case of radio or TV interference, relocate/reorient  
the antenna. If the antenna lead-in is 300 ohm ribbon  
lead, change the lead-in to coaxial type cable.  
If these corrective measures do not produce satisfactory  
results, please contact the local retailer authorized to  
distribute this type of product. If you can not locate the  
appropriate retailer, please contact Yamaha Electronics  
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA  
90620.  
The above statements apply ONLY to those products  
distributed by Yamaha Corporation of America or its  
subsidiaries.  
This equipment generates/uses radio frequencies and, if  
not installed and used according to the instructions found  
in the users manual, may cause interference harmful to  
the operation of other electronic devices.  
CAUTION  
Use of controls or adjustments or performance of  
procedures other than those specified herein may result  
in hazardous radiation exposure.  
ii En  
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.  
1
2
To assure the finest performance, please read this manual  
carefully. Keep it in a safe place for future reference.  
Install this sound system in a well ventilated, cool, dry, clean  
place – away from direct sunlight, heat sources, vibration,  
dust, moisture, and/or cold. For proper ventilation, allow the  
following minimum clearances.  
19 The batteries shall not be exposed to excessive heat such as  
sunshine, fire or like.  
20 VOLTAGE SELECTOR (Asia and General models only)  
The VOLTAGE SELECTOR on the rear panel of this unit  
must be set for your local main voltage BEFORE plugging  
into the wall outlet. Voltages are:  
Top : 2.5 cm (1 inch)  
.....................................AC 110/120/220/230-240 V, 50/60 Hz  
Rear: 2.5 cm (1 inch)  
Sides: 2.5 cm (1 inch)  
As long as this unit is connected to the wall outlet, it is  
not disconnected from the AC power source even if  
3
4
Locate this unit away from other electrical appliances, motors,  
or transformers to avoid humming sounds.  
you turn off this unit by  
.
Do not expose this unit to sudden temperature changes from  
cold to hot, and do not locate this unit in an environment with  
high humidity (i.e. a room with a humidifier) to prevent  
condensation inside this unit, which may cause an electrical  
shock, fire, damage to this unit, and/or personal injury.  
Avoid installing this unit where foreign objects may fall onto  
this unit and/or this unit may be exposed to liquid dripping or  
splashing. On the top of this unit, do not place:  
WARNING  
TO REDUCE THE RISK OF FIRE OR ELECTRIC  
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN  
OR MOISTURE.  
5
LASER SAFETY  
This unit employs a laser. Due to possible eye injury, only a qualified  
service person should remove the cover or attempt to service this  
device.  
Other components, as they may cause damage and/or  
discoloration on the surface of this unit.  
Burning objects (i.e. candles), as they may cause fire,  
damage to this unit, and/or personal injury.  
Containers with liquid in them, as they may fall and liquid  
may cause electrical shock to the user and/or damage to  
this unit.  
DANGER  
This unit emits visible laser radiation when open. Avoid direct eye  
exposure to beam. When this unit is plugged into the wall outlet, do  
not place your eyes close to the opening of the disc tray and other  
openings to look into inside.  
6
Do not cover this unit with a newspaper, tablecloth, curtain,  
etc. in order not to obstruct heat radiation. If the temperature  
inside this unit rises, it may cause fire, damage to this unit,  
and/or personal injury.  
The laser component in this product is capable of  
emitting radiation exceeding the limit for Class 1.  
7
8
9
Do not plug in this unit to a wall outlet until all connections  
are complete.  
Do not operate this unit upside-down. It may overheat,  
possibly causing damage.  
Do not use force on switches, knobs and/or cords.  
10 When disconnecting the power cable from the wall outlet,  
grasp the plug; do not pull the cable.  
11 Do not clean this unit with chemical solvents; this might  
damage the finish. Use a clean, dry cloth.  
12 Only voltage specified on this unit must be used. Using this  
unit with a higher voltage than specified is dangerous and may  
cause fire, damage to this unit, and/or personal injury.  
Yamaha will not be held responsible for any damage resulting  
from use of this unit with a voltage other than specified.  
13 To prevent damage by lightning, keep the power cord  
disconnected from a wall outlet or the unit during a lightning  
storm.  
14 Do not attempt to modify or fix this unit. Contact qualified  
Yamaha service personnel when any service is needed. The  
cabinet should never be opened for any reasons.  
15 When not planning to use this unit for long periods of time  
(i.e. vacation), disconnect the power cable from the wall  
outlet.  
16 Install this unit near the wall outlet and where the power cable  
can be reached easily.  
17 Be sure to read the “TROUBLESHOOTING” section in this  
manual on common operating errors before concluding that  
this unit is faulty.  
18 Before moving this unit, press to turn off this unit and then  
disconnect the power cable from the wall outlet.  
iii En  
ADDITIONAL INFORMATION  
CONTROLS AND FUNCTIONS ......................... 2  
Front panel................................................................. 2  
Rear panel connections.............................................. 3  
PLAYABLE DISC AND FILE FORMAT............8  
USING THE ADVANCED SETUP.......................9  
TROUBLESHOOTING .......................................10  
SPECIFICATIONS...............................................11  
PLAYING BACK iPod/USB DEVICE................. 6  
Connecting iPod/USB devices................................... 6  
Playing back iPod ...................................................... 6  
Playing back USB devices......................................... 6  
Disconnecting iPod/USB devices.............................. 7  
Supported iPod/USB devices..................................... 7  
If the batteries have leaked, dispose of them  
immediately. Avoid touching the leaked material or  
letting it come into contact with clothing, etc. Clean the  
battery compartment thoroughly before installing new  
batteries.  
Do not throw away batteries with general house waste;  
dispose of them correctly in accordance with your local  
regulations.  
Features  
Optical Digital Output  
Coaxial Digital Output  
CD-R, CD-RW Disc Playability  
(For details, refer to page 8.)  
MP3, WMA Disc Playability  
MP3, WMA File Playability Stored on USB Device  
(For details, refer to page 8.)  
iPod Playability  
Program Play (Audio CD only)  
Random-Sequence Play  
Single Track/File, Entire Disc/Folder/Whole device  
Repeat Play  
Handling the remote control  
The area between the remote control and this unit must  
be clear of large obstacles.  
Do not spill water or other liquids on the remote  
control.  
Do not drop the remote control.  
Do not leave or store the remote control in the  
following types of conditions:  
Repeat A-B Play (Audio CD only)  
Adjustable Display Information and Brightness  
PURE DIRECT Function  
– places of high humidity, such as near a bath  
– places of high temperature, such as near a heater or a  
stove  
Supplied accessories  
Please check that you have received all of the following  
parts.  
– places of extremely low temperatures  
– dusty places  
Power cable  
Remote control  
Batteries (AA, R6, UM-3) (×2)  
RCA stereo cable  
Do not expose the remote control sensor to strong  
lighting, in particular, an inverter type fluorescent  
lamp; otherwise, the remote control may not work  
properly. If necessary, position this unit away from  
direct lighting.  
Notes on batteries  
Change all of the batteries if you notice that the  
operation range of the remote control decreases.  
Use AA, R6, UM-3 batteries.  
Make sure that the polarities are correct. See the  
illustration inside the battery compartment.  
Remove the batteries if the remote control is not used  
for an extended period of time.  
Do not use old batteries together with new ones.  
Do not use different types of batteries (such as alkaline  
and manganese batteries) together. Read the packaging  
carefully as these different types of batteries may have  
the same shape and color.  
About this manual  
y indicates a tip for your operation.  
In this manual, audio CDs are referred to as “Audio  
CD”, MP3/WMA discs as “Data Disc”, and MP3/  
WMA files stored on the USB device as “USB”.  
The Audio CD , Data Disc and  
icons indicate music data formats that can be used in  
the operation.  
This manual is printed prior to production. Design and  
specifications are subject to change in part as a result of  
improvements, etc. In case of differences between the  
manual and the product, the product has priority.  
USB  
1 En  
INTRODUCTION  
CONTROLS AND FUNCTIONS  
Front panel  
1
(Power)  
Note  
Press to turn the power on/off.  
Connect using the ANALOG OUT terminals when you use  
PURE DIRECT mode (refer to page 3).  
y
• The power indicator above lights up when this unit is turned on.  
• Playback starts automatically if the power is turned on while a  
disc is set in the disc tray.  
7 Disc tray  
Loads a disc.  
2 Power indicator  
Lights up as follows:  
ON: Bright  
8
(Open/Close)  
Opens or closes the disc tray.  
9 Remote control sensor  
OFF: Off  
Receives signals from the remote control.  
3 iPod/USB port  
0
/
/
(Skip/Search backward),  
(Skip/Search forward)  
: Skips to the next track.  
Connect your iPod or USB device. See page 6 for details.  
4 iPod/USB indicator  
Off: CD mode is selected.  
Green: iPod/USB is connected and playable files have  
been detected (playback ready).  
/
: Skips back to the beginning of the current  
track.  
/
Press and hold  
(twice): Skips to the previous track.  
/
or  
/
to search  
backward/forward.  
5 CD/USB  
Swithes between CD mode and iPod/USB mode (see  
page 6).  
A
(Play)  
Starts playback.  
y
B
(Pause)  
When the iPod/USB indicator is not lit, this unit is in the CD  
Pauses playback. Press  
or  
to resume playback.  
mode.  
C
(Stop)  
6 PURE DIRECT  
Stops playback.  
Turns on or off the PURE DIRECT mode to improve  
audio quality.  
y
• The PURE DIRECT indicator lights up.  
• The digital output is turned off.  
• The front panel display is turned off during playback and only  
the minimum required indicators and messages are displayed  
during in the operation.  
2 En  
         
CONTROLS AND FUNCTIONS  
D Playback Status Indicator  
G Advanced setup indicator  
Lights up when this unit is in the play or pause mode.  
Indicates the enabled special modes. See “USING THE  
ADVANCED SETUP” (page 9) for details.  
E Source type indicator  
H Multi-information display  
Indicates the type of content being played back.  
F Time and playback mode indicator  
Indicates the current playback mode and the status of the  
time display (see pages 5 and 5 for playback modes, and  
page 5 for time display).  
Rear panel connections  
CAUTION  
Before making any connection, switch OFF the power to the unit, the amplifier and any other component.  
Connect the supplied power cable into  
the AC IN inlet on the rear panel when  
all connections are complete, and then  
plug in the power cable to the AC outlet.  
The audio signals are only output from the ANALOG OUT jacks  
when the PURE DIRECT mode is on.  
Amplifier  
Voltages are as follows:  
...............AC 110/120/220/230-240 V, 50/60 Hz  
VOLTAGE SELECTOR  
(Asia and General models only)  
CAUTION  
The VOLTAGE SELECTOR on the rear panel of this unit  
must be set for your local voltage BEFORE plugging the  
power cable into the AC wall outlet. Improper setting of  
the VOLTAGE SELECTOR may cause damage to this  
unit and create a potential fire hazard.  
230-  
Voltage indication  
240V  
VOLTAGE  
SELECTOR  
Rotate the VOLTAGE SELECTOR clockwise or  
counterclockwise to the correct position using a straight  
slot screwdriver.  
3 En  
   
CONTROLS AND FUNCTIONS  
Remote control  
Installing batteries in the remote control  
1
2
Press the  
compartment cover off.  
part and slide the battery  
Insert the two supplied batteries (AA, R6,  
UM-3) according to the polarity markings (+  
and –) on the inside of the battery  
compartment.  
3
Slide the cover back until it snaps into place.  
Using the remote control  
The remote control transmits a directional infrared beam.  
Be sure to aim the remote control directly at the remote  
control sensor on the front panel of this unit during  
operation.  
Within 6 m  
(20 ft)  
1 Infrared signal transmitter  
Sends infrared signals to this unit.  
y
This setting is retained even if you turn off this unit.  
5 Numeric buttons  
2 CD/USB  
Use to select directly a track on the disc or a file in the  
current folder.  
Switches between CD mode and iPod/USB mode (see  
page 6).  
6
(Search backward),  
forward)  
(Search  
y
This setting is retained even if you turn off this unit.  
Searches tracks backward/forward while the key is  
pressed.  
3 PROGRAM  
Turns on or off the program playback mode. See  
“Program playback” on the next page.  
7
(Skip backward),  
(Skip forward)  
: Skips to the next track.  
: Skips back to the beginning of the current track.  
(twice): Skips to the previous track.  
4 DIMMER  
Each time you press DIMMER, the brightness level  
changes by 4 levels.  
4 En  
   
CONTROLS AND FUNCTIONS  
8 FOLDER  
Data Disc  
(Folder down),  
USB  
(Folder up)  
D A/B Audio CD  
Repeats playback of a specified section of a track. To set  
the starting and end points (A and B), press A/B twice  
during playback.  
: Skips to the previous folder.  
: Skips to the next folder.  
Refer to page 6 for details.  
To cancel repeat A-B, press A/B again.  
9 OPEN/CLOSE  
Notes  
Opens or closes the disc tray.  
• You cannot set repeat A-B from one track to another track.  
• You cannot set repeat A-B for Data Disc and USB.  
0 PURE DIRECT  
Turns on or off the PURE DIRECT mode to improve  
audio quality. See page 2 for details.  
• If you stop playback by pressing  
(Stop), repeat A-B is canceled.  
• You cannot use repeat A-B when this unit is in the PURE  
DIRECT mode.  
y
E CLEAR  
This setting is retained even if you turn off this unit.  
Erases the programmed track.  
A RANDOM  
Turns on or off the random sequence playback mode.  
F ENTER  
Confirms a track number entered when you are  
programming tracks.  
Note  
The random playback mode is canceled when the disc is ejected.  
G
Pauses playback. Press  
(Play)  
Starts playback.  
B REPEAT  
or  
to resume playback.  
Repeats playback of a single track or all tracks. Each time  
you press REPEAT during playback, the repeat playback  
mode changes as follows:  
H
REP TRACK (single repeat playback): A single track  
is played back repeatedly.  
REP ALL (all repeat playback): All tracks (the entire  
disc) are played back repeatedly.  
See pages 8 for more information on MP3/WMA  
playback.  
I
(Stop)  
Stops playback.  
Data Disc  
USB  
REP FOLDER (folder repeat playback): All files (the  
entire folder) are played back repeatedly.  
Audio CD  
Program playback  
y
In the program playback mode, you can play back tracks  
in a programmed sequence.  
Repeat play also works with program play and random-sequence  
play.  
C DISPLAY  
Switches the time display. Each time you press DISPLAY  
during playback, the time display changes as follows:  
1
2
Press PROGRAM while playback is stopped.  
This unit is set to the program editing mode.  
Audio CD  
Select a track by using the numeric buttons  
and ENTER.  
Album name  
Artist name  
Elapsed time of the current  
track (default)  
3
Repeat step 2 to program the next track.  
You can program up to 24 tracks.  
Remaining time of the current  
track  
y
To cancel the programmed track, press CLEAR.  
Total remaining time of the  
disc  
Track name  
4
Press  
.
(CD TEXT disc only)  
Playback starts from the beginning of the  
programmed sequence.  
Data Disc  
USB  
Album name  
Artist name  
Title  
Elapsed time of the current  
file (default)  
y
To erase all programmed tracks, press CLEAR when the  
playback is stopped.  
Note  
The programmed tracks are erased when the disc is ejected or this  
unit is turned off.  
(Files including tag  
information only)  
5 En  
     
OPERATION  
PLAYING BACK iPod/USB DEVICE  
Connecting iPod/USB devices  
Notes  
iPod  
• Use the USB cable supplied with your iPod. If no USB cable is supplied, purchase one from Apple Inc.  
• Turn off your iPod.  
• Do not use a USB hub.  
1
4
Connect your USB device or iPod via USB cable  
Playing back iPod  
Playing back USB devices  
1
Press CD/USB to select the iPod/USB mode.  
The iPod/USB indicator on the front panel lights up  
in orange, then changes to green when playback is  
ready.  
1
2
Press CD/USB to select the iPod/USB mode.  
The iPod/USB indicator on the front panel lights up.  
Start playback.  
Filename is displayed in the front panel display and  
playback starts automatically in order by date and  
time of creation if playable files are in the USB  
device.  
2
Start playback.  
Operate your iPod to start playback, select a track,  
pause, and stop playback.  
y
3
4
Select a track.  
Press FOLDER  
select a folder, and then press b/a or numeric  
You can also use the following buttons: p (Playback), e  
(Pause), s (Stop), b (Skip backward), a (Skip forward),  
w (Search backward), and f (Search forward) on this unit  
or Remote Control.  
/
on the remote control to  
Note  
Stop playback.  
Press s (Stop).  
iPod may not function properly with this unit if software on iPod  
is not updated. Be sure to use the latest version of iPod software.  
See pages 8 for more information on MP3/WMA  
playback.  
6 En  
             
PLAYING BACK iPod/USB DEVICE  
Disconnecting iPod/USB devices  
Stop playback, and then disconnect your iPod or USB  
device. It is recommended that you press CD/USB to  
switch to the CD mode, confirm that the CD/USB  
indicator goes off, and then disconnect your iPod/USB  
device.  
CAUTION  
Do not disconnect your iPod or USB device while playing  
back from the connected device, or while “USB  
READING” appears in the front panel display.  
Supported iPod/USB devices  
Supported iPod models  
iPod classic (including 120GB model)  
iPod nano (2nd, 3rd and 4th generations)  
iPod touch (1st and 2nd generations)  
(as of April 2009)  
Notes  
• iPod is licensed on the condition that individuals perform  
privately duplication and playback of uncopyrighted material or  
material legally approved of duplication and playback.  
Infringement of copyright is prohibited by law.  
• Yamaha and suppliers accepts no liability for the loss of data  
saved on iPod connected to this unit. As a precaution, it is  
recommended that the files are made backup copies.  
Supported USB devices  
This unit supports USB mass storage class devices (e.g.,  
flash memories, card readers or portable audio players)  
that use FAT16 or FAT32 format.  
Notes  
• Some devices may not work properly even if they meet the  
requirements.  
• This unit does not support encrypted USB memory devices.  
• Do not connect devices other than USB mass storage class  
devices: USB chargers, USB hubs, PCs, external HDD, etc.  
• When you insert two or more memory cards at the same time  
into a card reader connected to the iPod/USB port on this unit,  
only one of the memory cards is recognized.  
• Yamaha and suppliers accepts no liability for the loss of data  
saved on the USB devices connected to this unit. As a  
precaution, it is recommended that the files are made backup  
copies.  
• Playability of and power supply to all kinds of USB devices are  
not guaranteed.  
7 En  
     
ADDITIONAL INFORMATION  
PLAYABLE DISC AND FILE FORMAT  
Playable MP3 and WMA files (USB  
Playable discs  
Use compact discs bearing the marks below.  
device and Data Disc)  
....  
Compact discs (digital audio)  
MP3  
Sampling  
frequency  
(kHz)  
Bitrate  
(kbps)  
Format  
....  
CD-R, CD-RW digital audio discs  
CD-R or CD-RW discs bearing one of  
the following phrases.  
FOR CONSUMER  
FOR CONSUMER USE  
FOR MUSIC USE ONLY  
Finalized CD-R or CD-RW discs.  
32-320 *  
8-160 *  
8-160 *  
32/44.1/48  
16/22.05/24  
8/11.025/12  
MPEG 1 Audio Layer-3  
MPEG 2 Audio Layer-3, 2  
MPEG-2.5 Audio Layer-2  
* Variable bitrate is also supported.  
Note  
WMA  
This compact disc player may not be able to  
play some CD-R/CD-RW discs or discs on  
which recording was not made correctly.  
Version 8  
Version 9 (Standard and variable bitrates are  
supported. Professional and Lossless are not  
supported.)  
Sampling  
frequency  
(kHz)  
....  
CD-TEXT discs  
Bitrate  
(kbps)  
Profile  
The disc title, artist name, and track  
name are also displayed in addition to  
the time displays when playing back a  
CD with CD TEXT.  
32-320 *  
16-32  
32/44.1/48  
16/22.05  
High Profile  
Mid Profile  
To play back an 8-cm (3-inch) CD  
* Variable bitrate is also supported.  
Place it in the inner recessed area of the disc tray. Do not  
put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.  
Notes  
• Playback for Data Disc starts in alphanumeric order.  
• Playback for USB starts in order by date and time of creation.  
• Copyright-protected WMA (DRM) files cannot be played back  
by this unit.  
• The disc must be ISO 9660 compatible.  
• Elapsed time may not be displayed correctly while playing back  
variable bitrate contents.  
To prevent a malfunction of this unit:  
Do not use any nonstandard  
shaped disc (heart, etc.) available  
on the market because it might  
damage the unit.  
Data Disc  
999  
USB  
32767  
256  
Do not use a disc with tape, stickers, or paste on it. If  
you use such a disc, the disc may get stuck in the  
unit, or damage to the unit may result.  
Maximum file number  
256  
Maximum folder number  
512  
512  
Maximum file number per  
folder  
8 En  
       
PLAYABLE DISC AND FILE FORMAT  
Use a soft-tipped pen when writing on the label side of  
the disc.  
When a disc is not being used, remove it from this unit  
and store in an appropriate case.  
Do not expose discs to direct sunlight, high  
temperature or high humidity for a long time.  
Handling compact discs  
Always handle with care so that the playing surface is  
not scratched. Do not warp discs.  
Note: Do not use any lens cleaners as they may be a  
cause of malfunction.  
To keep clean the playing surface, wipe with a clean,  
dry cloth. Do not use any type of disc cleaner, spray, or  
any other chemical-based liquid.  
Do not wipe with a circular motion; wipe straight  
outward from the center.  
USING THE ADVANCED SETUP  
This unit is equipped with the following two special  
modes, which may be useful for special purposes at stores  
or offices.  
To activate and configure Advanced setup, follow the  
steps below. Use the buttons on the front panel.  
POWER OFF  
Note  
Activate  
Advanced  
The special mode functions are incompatible with iPod.  
setup  
PURE DIRECT +  
PLAY MEM OFF  
(Open/Close) + POWER ON  
Play mode  
memory  
Play mode memory  
/
Retains the current playback mode (REPEAT and  
RANDOM) after turning off the power, saving the time of  
setting the playback mode again each time you turn on the  
power.  
PLAY MEM ON  
/
The RESUM indicator in the front panel display lights up  
when enabled.  
(Stop)  
Ready  
mode  
Ready mode  
/
Pauses playback after each track, allowing you to start the  
next track at any desired timing.  
The RDY indicator in the front panel display lights up  
when enabled.  
RDY MODE OFF  
RDY MODE ON  
/
Store  
settings  
(Play)  
POWER OFF  
*: Default Setting  
Next time you turn on the power, the unit turns on with  
the settings that you specified above.  
9 En  
   
TROUBLESHOOTING  
If the unit fails to operate normally, check the following points to determine whether the problem can be corrected by the  
simple measures suggested. If it cannot be corrected, or if the problem is not listed in the Problems column, disconnect  
the power cable and contact your authorized Yamaha dealer or service center for help.  
Referto  
page  
Problems  
Possible Causes  
Solutions  
This unit fails to turn The power cable is not connected to the AC IN  
Connect the power cable firmly.  
on.  
inlet on the rear panel or not plugged in the wall  
outlet.  
3
The disc tray does  
not close completely.  
A foreign object is obstructing the tray.  
Carefully check the disc tray and remove the  
foreign object.  
Disc playback does  
not start.  
The disc is damaged.  
Check the disc carefully; replace it if necessary.  
There is moisture on the laser pickup.  
Wait 20 to 30 minutes after turn on this unit ON  
before trying to play back a disc.  
The disc is loaded upside down.  
The disc is dirty.  
Reload the disc with the label side up.  
Clean the disc.  
9
The format of the MP3 or WMA file is not  
compatible with this unit.  
Replace the disc with a correctly recorded disc  
playable with this unit.  
9
9
The CD-RW (ReWritable) disc is not recorded  
correctly.  
Replace the disc with a correctly recorded disc  
playable with this unit.  
The disc is a non-standard disc not playable with Replace the disc with a correctly recorded disc  
9
2
this unit.  
playable with this unit.  
This unit is in iPod/USB mode.  
The connected iPod is not compatible with this  
Switch to disc mode by pressing CD/USB.  
iPod playback does  
Connect an iPod compatible with this unit.  
The compatible iPod are as follows:  
not start though iPod unit.  
is connected.  
iPod classic (including 120GB model)  
iPod nano (2nd, 3rd and 4th generations)  
iPod touch (1st and 2nd generations)  
7
(As of April 2009)  
This unit is in disc mode.  
Switch to iPod/USB mode by pressing CD/  
USB.  
6
6
8
USB playback does  
not start.  
Improper USB device connections.  
Connect the USB device again.  
The format of the MP3 or WMA file is not  
compatible with this unit.  
Replace the file with a correctly recorded file  
playable with this unit.  
This unit is in disc mode.  
Switch to iPod/USB mode by pressing CD/  
USB.  
6
8
Playback is delayed,  
or begins at the  
wrong place.  
The disc may be scratched or damaged.  
Check the disc carefully; replace it if necessary.  
No sound.  
Improper output cable connections.  
Improper amplifier operation.  
PURE DIRECT is turned on.  
Connect the cables properly. If the problem  
persists, the cables may be defective.  
3
Set the amplifier controls to the correct input  
selection.  
Sound of a  
component  
Turn PURE DIRECT off. Or make an analog  
connection.  
connected to the  
DIGITAL OUT jacks  
is not played.  
2, 3  
10 En  
 
TROUBLESHOOTING  
Referto  
page  
Problems  
Possible Causes  
Solutions  
Sound “skips”.  
This unit is being subjected to vibrations or  
impacts.  
Relocate this unit.  
Clean the disc.  
8
The disc is dirty.  
Sound “hums”.  
Improper cable connections.  
Securely connect the audio cables. If the  
problem persists, the cables may be defective.  
3
Noise from a nearby  
tuner.  
The tuner is too close to this unit.  
The disc may be warped.  
Move the tuner and this unit farther apart or turn  
off this unit.  
Noise from inside of  
the disc tray.  
Replace the disc.  
The remote control  
does not work or  
function properly.  
Wrong distance or angle.  
The remote control functions within a  
maximum range of 6 m (20 ft) and no more than  
30 degrees off-axis from the front panel.  
4
Direct sunlight or lighting (from an inverter type Reposition this unit.  
of fluorescent lamp, etc.) is striking the remote  
control sensor of this unit.  
4
The batteries are weak.  
Replace all batteries.  
SPECIFICATIONS  
Audio Section  
General  
• Frequency response ..................................... 2 Hz - 20 kHz, ± 0.5 dB  
• Harmonic distortion + noise (1 kHz).........................0.003 % or less  
• S/N ratio.................................................................... 105 dB or more  
• Dynamic range............................................................ 96 dB or more  
• Output voltage (1 kHz, 0 dB) ...........................................2.0 ± 0.3 V  
• Power requirements  
U.S.A. and Canada models .............................. AC 120 V, 60 Hz  
Australia model................................................ AC 240 V, 50 Hz  
Europe and U.K. models.................................. AC 230 V, 50 Hz  
Asia and General models ...... AC 110-120/220-240 V, 50/60 Hz  
China model ..................................................... AC 220 V, 50 Hz  
• Operating temperature............... +5 °C to +35 °C (+41 °F to +95 °F)  
Laser Diode Properties  
• Power consumption................................................................... 13 W  
• Dimensions (W × H × D)................................... 435 × 86 × 260 mm  
(17 1/8 × 3 3/8 × 10 1/4 in)  
• Material..................................................................................GaAlAs  
• Wavelength.............................................................................790 nm  
• Laser Output ..............................................................max. 1.23 μW*  
• Weight........................................................................3.5 kg (7.7 lbs)  
* This output is the value measured at a distance of about 200 mm  
from the objective lens surface on the Optical Pick-up Block.  
Please note that all specifications are subject to change  
without notice.  
iPod™  
“iPod” is a trademark of Apple Inc., registered in U.S. and  
other countries.  
“Made for iPod” means that an electronic accessory has  
been designed to connect specifically to iPod and has been  
certified by the developer to meet Apple performance  
standards.  
Apple is not responsible for the operation of this device or  
its compliance with safety and regulatory standards.  
11 En  
 
© 2009 Yamaha Corporation All rights reserved.  
Printed in Malaysia  
WU27830  

Yard Man 24A 061I401 User Manual
Superior W302 User Manual
Sony USM8GL User Manual
Sony Net MD Walkman MZ NF520D User Manual
Samsung SGH X820 User Manual
Samsung Cell Phone C3050 User Manual
Sabrent EC 3US35 User Manual
RCA RP5502I User Manual
Pioneer DVR 212DBK User Manual
Pioneer DVJ 1000 User Manual