Woods Equipment 8000 User Manual

operator's manual  
INCLUDES SERVICE INFORMATION  
MODEL 8000 & 8100  
CHIPPER  
PN-51210 (Rev. 7/98)  
C
O N T E N T S  
Contents  
SafetyInstructions.............................................................. 2  
SafetyDecals ............................................................................. 6  
Assembly........................................................................... 7  
AttachChipperChute ................................................................... 7  
AttachChuteExtensionTray ......................................................... 8  
AttachBlowerDischargeTube ....................................................... 8  
ConnecttheHydrostaticControlCable ............................................. 9  
ConnectPTOShaft ...................................................................... 9  
Controls........................................................................... 10  
Operation ......................................................................... 11  
Starting.....................................................................................11  
Chipping....................................................................................12  
Stopping ...................................................................................12  
ServiceandMaintenanceSchedule .................................... 13  
ServiceandMaintenance................................................... 14  
SharpeningChipperBlades ...........................................................14  
SettingChippingBladeClearance .................................................. 15  
AdjustingorReplacingtheDriveBelts ............................................ 16  
ClearingPluggedRotor ................................................................16  
RepairingorReplacingRotorBearings ............................................ 17  
GreaseableBearings ...................................................................18  
HydraulicFeed ................................................................. 19  
InstallingtheOptionalHydraulicFeedKit ........................................19  
HydraulicFeedInstructions ..........................................................22  
ControlArmOperation .................................................................23  
HydraulicSchematic ...................................................................23  
HydraulicFeedMaintenance ......................................................... 24  
HydrostaticPumpTroubleshooting .................................................24  
Troubleshooting ............................................................... 25  
AssemblyDiagramsandPartsLists ................................... 26  
ServiceAccessories ...................................................................26  
ChuteandRotorAssemblyPartsList ............................................. 26  
ChuteandRotorAssemblyDiagram ...............................................27  
ChipperBaseAssemblyDiagram ................................................... 28  
ChipperBasePartsList ............................................................... 28  
Hyd.FeedAssy.DiagramandParts.................................... 30  
HydraulicFeedAssemblyDiagram .................................................30  
HydraulicFeedPartsList .............................................................32  
Specifications .................................................................. 33  
Warranty  
PN-51210 (Rev. 7/98)  
S
A F E T Y  
I
N S T R U C T I O N S  
SafetyInstructions  
Thischipperisdesignedandtestedtoofferreasonablysafeservice.  
Failuretooperateitinaccordancewiththefollowingsafety  
instructions MAY RESULT IN PERSONAL INJURY!  
A safety message alerts you to potential hazards that could hurt you or others.  
Each safety message is proceeded by one of three words: DANGER,  
WARNING, or CAUTION.  
You WILL be KILLED or  
SERIOUSLY HURT if you don't  
follow instructions  
DANGER  
You CAN be KILLED or  
WARNING  
CAUTION  
SERIOUSLY HURT if you don't  
follow instructions.  
You CAN be HURT or DAMAGE  
machine if you don't follow  
instructions.  
BeforeOperating  
Read the owners manual before operating this equipment.  
Do not allow children to operate this equipment.  
Do not operate this equipment in the vicinity of bystanders.  
Do not allow hands—or any part of body or clothing— inside the  
feeding chamber, discharge chute, or near any moving part.  
Shut off the power source and make sure all moving parts are com-  
pletely stopped before inspecting or servicing any part of the machine.  
Preparation  
Wear safety glasses at all times while operating the machine. One pair is  
provided with each chipper.  
Avoid wearing loose-fitting clothing. Never operate this machine  
wearing loose clothing particularly if it has drawstrings which can wrap  
around or get caught in the machine.  
Operate the machine only on a level surface.  
Do not operate the machine on a paved, concrete, or hard gravel surface.  
Operating on a hard surface causes discharged material to rebound and  
kickback. It will also cause increased machine vibration. Increased  
vibration causes the machine to move and will promote premature wear  
of parts or loosening of fasteners.  
PN-51210 (Rev. 7/98)  
2
S
A F E T Y  
I
N S T R U C T I O N S  
Visually check that all screws, nuts, bolts, and other fasteners are properly  
secured before starting the machine. Check all screws, nuts, bolts, and other  
fasteners once every 10 hours of operation for proper tightness to insure  
everything is in proper working condition.  
Operation  
Empty the cutting chamber before starting the machine.  
Exclude pieces of metal, rocks, bottles, cans, and other foreign objects  
when feeding chipable material into the machine.  
Shut off the engine or PTO and allow the machine to stop if the cutting  
mechanism strikes any foreign object or if the machine starts making an  
unusual noise or vibration. After machine stops:  
a) Inspect for damage.  
b) Replace or repair any damaged parts.  
c) Check for and tighten any loose parts.  
Do not allow processed material to build up in the discharge area; this may  
prevent proper discharge and result in kickback of material through the feed  
opening.  
Do not allow hands or any other part of the body or clothing inside the  
feeding chambers, discharge chute, or near any moving part.  
Keep all guards and deflectors in place and in good working condition.  
Stand clear of the discharge area when operating this machine.  
Keep your face and body back from the feed opening.  
Do not over reach. Keep proper balance and footing at all times.  
Do not transport or move machine while the machine is running.  
Disengage PTO and shut off tractor engine if the machine becomes clogged.  
Allow machine to come to a complete stop before clearing debris.  
WARNING: Keep body and clothing away from PTO shaft when running.  
Connect 3 pt. hitch pins and snap pins, connect PTO shaft, and have leg  
stands solidly on the ground when in use.  
Lock the rotor by inserting a bolt or punch through the locking holes on the  
side of the rotor housing before moving. To move unit: shut off PTO and lift  
3 pt. hitch.  
Keep guards and shields in place at all times while operating. Disengage  
tractor PTO and shut off engine before removing guards or shields.  
Keep hands, feet, and clothing away from all PTO drive parts.  
Never clean, lubricate, or adjust the chipper when it is running.  
PN-51210 (Rev. 7/98)  
3
S
A F E T Y  
I
N S T R U C T I O N S  
Put transmission in neutral or park and disengage before starting tractor.  
WARNING: This chipper is designed to be used with tractor PTO's rated at  
20 to 60 horsepower. Using this chipper with PTO's above 60 horsepower  
may cause belt and machine damage in overload conditions.  
AdditionalSafetyRulesforPTOModels  
Stay alert and pay attention when PTO chipper is operating.  
Keep bystanders, especially children, away from the PTO driveline.  
Connect 3 pt. hitch pins and snap pins, connect PTO shaft and have leg  
stands down and secure when in use.  
Check the driveline to ensure it is attached securely to the tractor.  
Keep guards and shields in place at all times while operating. Disengage  
tractor PTO and shut off engine before removing guards or shields.  
Keep hands, feet, and clothing away from all PTO drive parts.  
Do not clean, lubricate, or adjust the PTO when it is running.  
Clothing worn by operator must be fairly tight. Never wear loose  
jackets, shirts, shirt sleeves or pants when working around PTO. Tie  
long hair back or put under a cap.  
PN-51210 (Rev. 7/98)  
4
S
A F E T Y  
I
N S T R U C T I O N S  
Keep hydraulic hoses, electric cords, chains, and other items from  
contacting the driveline.  
Make sure transmission is in neutral or park and PTO is disengaged  
before starting the tractor.  
Do not exceed the recommended 540 RPM PTO operating speed.  
Disconnect PTO and shut off tractor when this unit is stopped for  
servicing, inspection, storage, or to change an accessory.  
Shut off the PTO, lift 3 pt. hitch, and adjust leg stands if needed to move  
the unit.  
Read and follow instructions on PTO safety decals.  
WARNING!RecommendedtractorPTOhorsepoweris15HPto30HP.Useoftheseunitson  
tractorsabove30PTOhorsepowermaycausebeltandmachinedamageinoverloadconditions.  
SafeStorage  
Disengage PTO when this equipment is stopped for servicing,  
inspection, storage, or to change an accessory.  
Store the machine out of reach of children. Clear debris from inside the  
machine and store in a dry area for storage periods of three months or  
more.  
PN-51210 (Rev. 7/98)  
5
S
A F E T Y  
D
E C A L S  
SafetyDecals  
Safetyandinstructiondecalsarelocatedonthechipperframeandengine.  
Replaceanydamagedorunreadabledecal.  
NOTE: See parts drawings and lists for location of safety decals on the  
chipperframe.  
PN 57835, French Safety Decal Kit  
PN51284  
PN51361  
PN51281  
PN51373  
PN51375  
PN51312  
PN-51210 (Rev. 7/98)  
6
A
S S E M B L Y  
Assembly  
For instructions on assembling the hydraulic feed kit, see page 20.  
AttachChipperChute  
Do not operate this unit without the chipper chute correctly installed. Rotating  
cutting blades can cause serious personal injury.  
1. Remove chipper from shipping crate. Place unit on a level surface before  
attempting to assemble. See torque chart for minimum tightening torque.  
2. Mount the chipper chute to the frame mounting bracket using eight 3/8" x 1"  
bolts and locknuts. Use three bolts on each side and two on the bottom (see  
figure 1). Attach the chute directly to the hydraulic feed unit as described  
above for models with factory-installed hydraulic feed.  
TorqueChart  
Standardminimum  
tighteningtorquefor  
normalassembly  
applications.  
Bolts (SAE GR5)  
Size  
5/16"  
3/8"  
Ft.Lbs.  
20  
35  
1/2"  
75  
Screws  
Size  
Ft.Lbs.  
5/16"Set  
15  
Chipper  
Chute  
Figure1  
PN-51210 (Rev. 7/98)  
7
A
S S E M B L Y  
AttachChuteExtensionTray  
1. Slide the chute extension tray over the chipper chute as shown in figure  
2 after mounting the chute to the chipper frame. Make sure you position  
the lip on the extension tray behind the lip on the chipper chute. Align  
the five bolt holes in the chute extension tray with the bolt holes in the  
hinge.  
2. Insert five 3/8" x 1" carriage bolts (included in owners kit packaged with  
the chipper) through the tray and the extension hinge. Secure the bolts  
with washers and nuts. Secure with hairpin clips.  
AttachBlowerDischargeTube  
1. Attach the blower discharge tube to the mounting flange on the chipper  
frame (see figure 3). Half of the mounting clamp is already attached to  
the tube. Slide the tube into the flange and tighten the bolts to secure it.  
Install the second half of the clamp to the tube and flange. Rotate the  
ock it in place with the handle to make sure it is  
Hairpin  
Clip  
Positionthislip  
behindthelipon  
thechipperchute  
Blower  
shownbelow.  
Discharge  
Holdtheextension  
Tube  
traydirectlyabove  
thechipperchute  
andslideit  
ExtensionTray  
downward.  
FeedControl  
Lever(Models  
withhydraulic  
feedonly.)  
s
Chipper  
Chute  
Extension  
Hinge  
Figure2  
Figure3  
PN-51210 (Rev. 7/98)  
8
A S S E M B L Y  
ConnecttheHydrostaticControlCable  
(Formodelswithfactoryinstalledhydraulicfeed.)  
1. Remove the clevis assembly from the hydrostatic control cable end (see  
figure 4). Remove one nut on the cable end. Insert the cable end into the  
hole in the cable anchor weldment. Replace the nut and the clevis assembly.  
2. Attach the clevis assembly to the center hole on the feed control lever.  
3. Adjust the cable detent ball to contact the detents in the cable anchor  
weldment when the control arm is in the forward position or reverse position.  
Important! See hydrostatic pump start-up procedure.  
ConnectPTOShaft  
1. Connect the PTO shaft female end to the rotor shaft using key stock and two  
set screws contained in the owner's kit.  
2. Connect the opposite end of the PTO shaft to the tractor.  
3. Check all screws, bolts, and nuts for tightness. See torque chart, page 5 for  
minimum tightening torque.  
Clevis  
Assembly  
Detent  
Ball  
Insertcable  
throughhole  
Nut  
FeedControl  
Lever  
CableAnchor  
Weldment  
Hydrostat  
ControlCable  
Figure4  
PN-51210 (Rev. 7/98)  
9
C O N T R O L S  
Controls(seefigure5)  
1. Three pt. Hitch Connection: Mounts chipper to tractor 3 pt. hitch.  
Connect direct for category 1.  
2. PTO Shaft: Connects chipper to tractor PTO shaft. Avoid driveline  
angles over 20 degrees on PTO shaft when unit is in use.  
3. Drive Belt Shield: Never remove shield while machine is running.  
4. Chipper Chute: Feeds materials to the chipper blades for chipping.  
5. Leg Stands: Never move machine unless legs are in UP position and  
clear the ground.  
6. Rotor Access Cover: Tilts up to remove chipper blades and to service  
rotor assembly.  
7. Discharge Tube: Chipped materials will exit through this tube. Tube is  
adjustable 360 degrees.  
8. Adjustable Chipping Anvil: Adjusts to vary the size of chips.  
9. Rotor Shaft Bearing Cover: Rotor shaft has lock assembly to lock rotor  
in place while moving.  
PTOModel  
Controls  
Figure5  
7
6
4
9
8
3
2
1
5
PN-51210 (Rev. 7/98)  
10  
O
P E R A T I O N  
Operation  
CAUTION: Wear safety glasses at all times when operating the  
machine. Do not wear loose fitting clothing. The operator should always  
wear heavy boots, gloves, pants, and shirt. Use common sense and practice  
safety to protect yourself from branches, sharp objects, and other harmful  
objects.  
NOTE: The heavy rotor continues to turn for some time after the tractor  
has been shut off. The rotor is stopped when no noise or machine vibration  
is present. Inserting a branch into the chipper chute to contact the blades  
slows the rotor and shortens stopping time.  
NOTE: Minimum and maximum telescoping on the PTO shaft is 20-28  
inches. This will leave 4 inches overlap at maximum telescoping distance  
(see figure 6).  
Starting  
1. Place tractor transmission in park or neutral and set parking brake.  
Connect 3 pt. mounts between the chipper and tractor. Secure connec-  
tions with snap pins. Adjust 3 pt. top link so chipper sits level.  
2. Connect PTO shaft to tractor. Make sure you are using the correct RPM  
machine. Do not operate machine at speeds different than specified on  
shield.  
3. Do not inspect or work on PTO drive area without first disengaging PTO  
and shutting off tractor engine.  
4. Start tractor engine and engage PTO drive clutch (see tractor owner's  
manual). Increase engine speed to rated PTO RPM position.  
WARNING:This  
chipperisdesigned  
tobeusedwith  
tractorPTO'srated  
at20to60  
horsepower. Using  
thischipperwith  
PTO'sabove60  
horsepowermay  
causebeltand  
Figure 6  
Telescoping Type  
20 to 28 inches will leave  
at least 4 inches overlap  
machinedamagein  
overloadconditions.  
PN-51210 (Rev. 7/98)  
11  
O
P E R A T I O N  
Chipping  
WARNING: Keep face and body away from the feed opening. Do not  
over reach. Keep proper balance and footing at all times.  
The Woods chipper is designed to chip a variety of materials into a more  
readily decomposing or handled condition. The following guidelines can be  
used to help you get started. Please read and follow all safety instructions in  
this manual. Failure to operate the chipper in accordance with the safety  
instructions MAY RESULT IN PERSONAL INJURY!  
Be sure the unit is at full operating speed before starting to chip material.  
Select limbs up to 8 inches in diameter. Trim side branches that cannot  
be bent enough to feed into the chipper chute. Hold small diameter  
branches in a bundle and feed simultaneously.  
Feed brush from the side of the infeed chute rather than from the front.  
Step aside to avoid being hit by brush moving into the chipper.  
Never lean into the infeed chute to push objects into the cutting device. Use  
a push stick or brush paddle.  
Do not use shovels or forks to push brush. They can go through the chipper,  
are expensive to replace, and cause major damage. Metal pieces can come  
back like shrapnel to injure or kill.  
Never push brush into the infeed chute with your feet.  
Place limb, butt end first, into the chipper chute until it contacts the  
chipper blades. The actual feed rate of the limb into the chipper will  
depend on the type of material fed and sharpness of the cutting blades.  
Alternately insert and retract the limb or insertcontinuouslyataratethat  
will not stall the tractor. Rotating the branch as you feed it will improve  
cuttingaction.  
NOTE: The chipping blades dull with use and require periodic sharpening.  
Refer to service and maintenance, "sharpening chipper blades" for  
instructions.  
Stopping  
WARNING: Do not leave machine unattended, or attempt any inspection or  
service unless PTO is disengaged and tractor engine is shut off. Allow  
machine to come to a complete stop. To stop machine, proceed as follows:  
1. Move tractor throttle to SLOW position.  
2. Disengage PTO lever and shut off tractor engine.  
3. Allow machine to come to a complete stop.  
NOTE: The heavy rotor continues to turn for some time after the engine or  
tractor has been shut off. The rotor is stopped when no noise or machine  
vibration is present. Inserting a branch into the chipper chute to contact the  
blades slows the rotor and shortens stopping time.  
PN-51210 (Rev. 7/98)  
12  
S
E R V I C E A N D  
M
A I N T E N A N C E  
S
C H E D U L E  
ServiceandMaintenanceSchedule  
Interval  
Every  
100  
Before  
Each  
Use  
Every  
10  
Hours  
Every  
25  
Hours  
Every  
50  
Hours  
Every  
200  
Hours  
Every  
300  
Hours  
Every  
800  
Hours  
Every  
1
years  
InspectionItems  
Check Nuts & Bolts (Entire machine)  
Check  
Hours  
Replace  
Check  
*
Clean  
Hydraulic Filter Element  
Replace  
Check Hydraulic Control Cable  
Check Sharpness of Chipper Blades  
Grease Bearings and Pivots  
Check Bolts: Chipper Blade, Chipper  
Anvil, Rotor Paddles  
Check Drive Belt  
Clean Machine  
Note: (*) Service more frequently when used in dusty conditions  
Beforeinspectingorrepairinganypartofthemachine,shutofftheengineandmakesureall  
movingpartshavecometoacompletestop.  
Indicates first hours of use.  
PN-51210 (Rev. 7/98)  
13  
S
E R V I C E A N D  
M
A I N T E N A N C E  
ServiceandMaintenance  
WARNING: Shut offPTO and make sure all moving parts have come  
toacompletestopbeforeinspectingorservicinganypartofthemachine.  
Thechippingbladesaresharp!Usecarewhenworkingonmachinetoavoid  
injury.  
WARNING: The rotor assembly has a lock mechanism. Use the lock  
mechanism at all times when working on the rotor assembly. Remove plastic  
bearing cover under chipper chute. There is a hole in the rotor jack shaft and  
a matching hole in the bracket mounted to the rotor bearing front side.  
Install a punch through the rotor shaft and bracket to lock the rotor in place.  
SharpeningChipperBlades  
The chipper blades dull, making chipping difficult. It is recommended to  
sharpen the chipper blades every 5-15 hours of chipper operation. To  
remove the chipping blades for sharpening:  
1. Remove the two 3/8" retaining bolts holding access cover to main frame  
assembly.  
2. Tilt access cover over to allow rotor access. Rotate the rotor so the bolts  
holding a chipping blade are most accessible.  
3. Remove the two allen head bolts holding the blade itself. Repeat for all  
four blades. The four chipping blades have two edges per blade and can  
be reversed one time each before sharpening. Remove and reverse the  
chipping blades if both sides have not been used. Reinstall chipping  
blades and proceed with chipping.  
To grind the angled edge of the chipping blade to 45 degrees (see figure 7):  
Grind the blades on a slow-speed wet grinder, if possible, or have them  
Sharpening  
Edges  
45  
t
s
t
t
Figure7  
0.38  
Figure8  
PN-51210 (Rev. 7/98)  
14  
S
E R V I C E  
A N D  
M
A I N T E N A N C E  
sharpened by a professional. Be careful when grinding if using a bench  
grinder so the blade material does not get too hot and change color–this will  
remove the blade's special heat treated properties. Use short grinding times  
and cool with water. Remove an equal amount off each blade to maintain  
balance. Replace the chipping blades and tighten bolts to 75 ft. lbs. Close  
cover and replace bolts.  
Youdonothaveto  
removetherotorfromthe  
mainframetorepairthe  
chipperbladesorpaddles  
locatedonthebackofthe  
rotorassembly.  
ChippingBladeSharpeningTips  
Poor chipping performance is usually a result of dull chipping blades. Check  
for the following symptoms if chipper performance has decreased:  
Severe vibration when feeding material into the chipper.  
Small diameter branches do not self-feed.  
Chips discharge unevenly or have stringy tails–especially when chipping  
green branches.  
Check for permanent damage before you sharpen the chipping blades.  
Replace the blade if:  
The blade is cracked (especially around the bolt holes) or the edges are  
too deeply chipped to be ground smooth.  
The base of the cutting edge is worn or has been re-sharpened so it is too  
close to the rotor chipping slot.  
SettingChippingBladeClearance  
Thefour-edgedchippinganvillocateddirectlyunderthechipperchute  
shouldclearthechippingbladeby1/16inchto3/16inch. Thechipping  
anvilisadjustableandreversible.  
ToAdjust:  
1. Lift rotor access cover and expose rotor (see figure 8, page 12). Loosen  
the three 1/2" bolts holding the chipper anvil to the frame.  
2. Measure the amount of clearance between chipping blade and chipping  
anvil from inside of housing.  
3. Adjust inward or outward to desired measurement.  
4. Tighten bolts on chipping anvil to 75 ft. lbs. and resume operation.  
Removethethreeboltsholdingtheanvilanduseoneoftheotherthree  
edges if the chipping anvil edge is damaged or worn unevenly. Adjust for  
correctmeasurement.  
PN-51210 (Rev. 7/98)  
15  
S
E R V I C E A N D  
M
A I N T E N A N C E  
AdjustingorReplacingDriveBelts  
Checktheconditionofthedrivebeltsannuallyorafterevery30hoursof  
operating,whichevercomesfirst.Replacecracked,frayed,orwornbelts.  
Proceedasfollowstoreplaceoradjustthedrivebelt:  
1. Disengage PTO and shut off tractor engine.  
2. Remove PTO shaft from tractor; disconnect machine from 3 pt. hitch.  
3. Remove round shield connected to belt guard covering the PTO shaft by  
removing two 5/16" nuts.  
4. Remove PTO shaft from chipper by removing two set screws and pulling  
shaft off.  
5. Remove belt guard covering pulleys and belts.  
6. Lift spring loaded idler pulley off of belt and remove belt.  
7. Install new belt and reverse above instructions to complete belt  
replacement.  
ClearingPluggedRotor  
WARNING: Shut off the tractor engine and allow the machine to  
completely stop before clearing debris if the machine plugs. Do not operate  
the machine without proper guards and screens in place.  
The chipper can plug if too large or too much material is fed into it. Proceed  
as follows to clear plugged rotor:  
1. Disengage PTO and shut off tractor engine.  
2. Lift rotor access cover.  
3. Clean the debris out of the chipping rotor. Turn the rotor by hand to be  
sure it is free to rotate.  
4. Replace rotor access cover.  
5. Start tractor, engage PTO, and resume operation.  
PN-51210 (Rev. 7/98)  
16  
S
E R V I C E  
A N D  
M
A I N T E N A N C E  
RepairingorReplacingRotorBearings  
1. Remove two 3/8" retaining bolts holding access cover to main frame  
assembly. Tilt access cover over to allow rotor access.  
2. Remove large belt guard (three 5/16" bolts).  
3. Loosen bolts on hydraulic pump and remove hydraulic pump belt.  
Remove the bushing and pulley from the rotor shaft using the push bolts  
from the bushing.  
4. Lift belt idler pulley off drive belt and remove belt from pulleys. Remove  
the bushing and pulley from the rotor shaft using the push bolts from the  
bushing.  
WARNING: The rotor assembly has a lock mechanism. Use the lock  
mechanism at all times when working on the rotor assembly. Remove plastic  
bearing cover under the chipper chute. There is a hole in the rotor jack shaft  
and a matching hole in the bracket mounted to the rotor bearing front side.  
Install a punch through the rotor shaft and bracket to lock the rotor in place.  
5. Remove four 1/2" bolts on each rotor bearing and remove punch used to  
lock the rotor.  
6. Lift the rotor assembly completely out of the frame using an overhead  
hoist or lifting device. The complete rotor assembly weighs 275 lbs.  
7. Remove 3/8" bolts and collar from front once the rotor assembly is out  
of the frame. Remove both bearings with a puller and place new  
bearings on rotor shaft. Replace collar.  
8. Return the complete rotor assembly to the chipper frame with an  
overhead hoist or lifting device.  
9. Slide rotor back until front collar is tight against the front bearing. Lock  
the front bearing and install four 1/2" bolts on each bearing to secure  
them to the frame. Tighten bolts to 75 ft. lbs. Check and adjust chipper  
anvil if needed. Lock rear bearing.  
10. Slide rear collar on shaft against rear bearing. Slide bushing onto shaft  
with flange against collar and lock bushing to shaft. Attach large pulley  
to bushing. Replace drive belt on pulleys and lower belt idler. Check  
alignment of pulleys and adjust engine if needed.  
11. Close cover and replace bolts.  
12. Replace hydraulic pump bushing and pulley. Replace hydraulic pump  
belt. Readjust hydraulic pump belt tension by sliding the hydraulic pump  
in the mounting slots. Tighten bolts.  
13. Replace belt guard and resume operation.  
14. Start tractor engine and engage PTO drive clutch (see tractor owner's  
manual). Increase engine speed to rated PTO RPM Position. Test unit,  
readjust pulleys, and belt tension if needed.  
PN-51210 (Rev. 7/98)  
17  
S
E R V I C E  
A N D  
M
A I N T E N A N C E  
Important!  
Check the bolts on the following for correct torque (75 ft. lbs.) every  
10 hours of operation:  
• Hydraulic feed roller bearing  
• Hydraulic motor mounting  
• Chipper rotor bearing  
• Chipper blades  
• Rotor paddles  
• Chipper anvil  
Warning: Failure to maintain proper fastening torque (75 ft. lbs.) on bolts  
for the components listed above may result in severe damage to the chipper  
and/or personal injury!  
GreaseableBearings  
The PTO model has ten grease zerks. Minimal periodic greasing is needed  
on these points every 50 hours:  
Four grease zerks on the PTO shaft itself.  
Two greaseable bearings on the rotor shaft.  
Two greaseable bearings on the bottom jack shaft.  
One idler arm pivot  
One discharge chute  
PN-51210 (Rev. 7/98)  
18  
H
Y D R A U L I C  
F
E E D  
I
N S T A L L A T I O N  
HydraulicFeed  
InstallingtheOptionalHydraulicFeedKit(Formodelswithoutfactory  
installedhydraulicfeed.)  
InstalltheRollerAssembly  
1. Remove the bolts fastening the chipper chute to the rotor housing weldment.  
2. Remove the chipper chute mounting plate.  
3. Hold the roller assembly up to the rotor housing weldment. Secure the roller  
assembly with 3/8" x 1-1/2" bolts, washers, and nuts.  
4. Attach the chipper chute to the roller assembly with 3/8" x 1-1/2" bolts,  
washers, and nuts.  
AttachtheControlArm  
1. Remove the canvas chipper chute flap and angle.  
2. Fasten the cable anchor to the chipper chute with 3/8" x 1-1/4" bolts,  
washers, and nuts.  
3. Attach control pivot and extension hinge to the chipper chute bottom with  
3/8" x 1-1/2" bolts, washers, and nuts.  
4. Put three 5/8" washers on both control pivot shafts.  
5. Place the control arm shaft holes over the control pivot shafts.  
6. Place a 5/8" bearing over each pivot shaft and fasten each bearing to the  
control arm with two 3/8" x 1" bolts and nuts.  
7. Attach the feed control lever to the cable anchor weldment by inserting a  
5/16" x 2" bolt through the bolt holes. Place the drift cutter spring over the  
end of the bolt. Secure the bolt and spring with a 5/16" washer and nut.  
8. Put the detent ball into the detent cavity on the feed control lever. Insert the  
detent spring into the detent cavity. Secure the spring and the ball by  
threading a 3/8" x 1" bolt through a 3/8" nut and then threading the bolt into  
the detent cavity.  
9. Connect the control arm to the feed control lever with the control tie rod  
strip. Place a 5/16" washer and an idler pivot spacer over a 5/16" bolt. Insert  
the bolt through the bolt hole in one end of the control tie rod strip and the  
top bolt hole on the feed control lever. Secure the bolt with a 5/16" washer  
and nut. Insert a 5/16" x 1" bolt (with a 5/16" washer and idler pivot spacer)  
through the other bolt hole in the control tie rod strip and the control arm.  
Secure with a 5/16" washer and nut.  
PN-51210 (Rev. 7/98)  
19  
H
Y D R A U L I C  
F
E E D  
I
N S T A L L A T I O N  
Installthe6.6"Pulley  
1. Remove the chipper drive belt guard.  
2. Put the 6.6" pulley on the rotor shaft end.  
3. Place the 1.75" bushing on the rotor shaft and put the 3/8" x 1/4" key into  
the bushing slot. Do not tighten the bushing yet.  
MounttheHydrostaticPump  
1. Attach the pump control arm to the pump control on the hydrostatic pump  
with two 1/4" x 1/2" bolts.  
2. Mount the pump mount bracket to the hitch weldment by inserting two 3/8"  
x 1-1/2" bolts through the bolt holes. Place the cable attachment angle over  
the bolt ends on the other side of the hitch weldment. Secure the bolts with  
two 3/8" washers and nuts.  
3. Slide the 4" pulley over the pump shaft. Slide the 15mm bushing next to the  
pulley. Place the 5mm x 25mm key into the bushing. Do not tighten the  
bushing yet.  
ConnecttheHydrostaticCable  
1. Insert the hydrostatic control cable end (the end without nuts attached)  
through the cable hole in the hitch weldment.  
Figure9  
Roller  
Assembly  
Hydrostatic  
Motor  
Crossover  
ReliefValve  
PN-51210 (Rev. 7/98)  
20  
H
Y D R A U L I C  
F
E E D  
I
N S T A L L A T I O N  
2. Thread the cable end into the cable pivot pin. Insert the pivot pin into the  
hole in the pump control arm. Secure the pivot pin with a 1/4" washer  
and a 3/32" x 3/4" cotter pin.  
3. Place the cable clamp shim and clamp on the cable exterior (as shown  
on page 20). Secure the cable, clamp, and shim to the cable attachment  
angle with two 1/4" x 3/4" bolts and locknuts.  
4. Remove one nut on the opposite cable end. Insert the cable end into the  
hole in the cable anchor weldment. Replace the nut.  
5. Attach the clevis assembly to the center hole on the feed control lever.  
AttachtheValveandMounttheReservoir  
1. Attach the crossover relief valve to the chipper stand with two 3/8" x 2"  
bolts, washers, and nuts.  
2. Attach the reservoir support weldment to the chipper rotor housing with  
two 5/16" x 3/4" bolts, washers, and nuts.  
3. Put the tank on the reservoir support.  
4. Place the reservoir straps over the tank and secure with 5/16" x 3/4"  
bolts, washers, and locknuts.  
ConnecttheBelt  
1. Attach the belt to the 6.6" rotor shaft pulley and the 4" hydrostatic pump  
pulley.  
2. Align the two pulleys with a straight edge.  
3. Tighten both pulley bushings.  
4. Move pump to tighten belt.  
5. Install the hydraulic hoses as shown on page 20. Follow hydrostatic  
pump start up and maintenance instructions on pages 20 and 21.  
6. Replace chipper drive belt guard.  
7. Install chute extension tray as described on page 6.  
PN-51210 (Rev. 7/98)  
21  
H
Y D R A U L I C  
F
E E D  
O
P E R A T I O N  
I
N S T R U C T I O N S  
HydraulicFeedOperatingInstructions  
Fluids  
Handle pressurized hydraulic fluid carefully. Escaping pressurized hydraulic  
fluid has sufficient force to penetrate skin causing serious injury. This fluid  
may also be hot enough to burn. Serious infection or reactions can develop  
if proper medical treatment is not administered immediately.  
Premium hydraulic fluids containing high quality rust, oxidation, and foam  
inhibitors are required. These include premium turbine oils, API CD engine  
oils per SAE J183, M2C33F or G automatic transmission fluids meeting  
Allison C-3 or Caterpillar TO-2, and certain specialty agricultural tractor  
fluids.  
HydrostaticPumpStartUpProcedure  
Follow this start-up procedure to start a new installation or to restart an  
installation if the hydrostatic pump was removed from the system.  
Hydrostaticpressure  
controlledbythe  
1. Make sure all system components (reservoir, fittings, etc.) are clean  
before starting the hydrostatic pump.  
crossoverreliefvalveis  
factorysetat1750PSI.  
A2000PSIshimkitis  
availableforextreme  
conditions.  
2. Fill the reservoir with recommended hydraulic fluid (filter before filling).  
3. Fill the inlet line leading from the reservoir to the charge pump before  
start-up. Loosen the fitting on this inlet line until oil bleeds out.  
Warning! Do not start engine unless pump is in neutral or detent position on the  
cable.  
4. Start the engine and run at the lowest possible RPM.  
5. Refill the reservoir as necessary. The oil level in the reservoir drops and  
bubbles appear in the fluid as air purges from the unit.  
6. Run the unit in both directions for several minutes until any remaining  
air is purged from the unit. Refill the reservoir as necessary.  
7. Loosen a motor fitting and oil-bled to remove air from the system (use  
same procedures as steps 3-5) if needed.  
8. Disengage PTO, check for and correct any fluid leaks, and check the  
reservoir level. Add fluid if necessary.  
The hydrostatic pump is now ready for operation.  
Input Shaft Seal  
ChargePump  
Figure10  
ChargeCheckValve  
Control Shaft Seal  
BypassValve  
Pump-Component  
Locations  
PN-51210 (Rev. 7/98)  
22  
H
Y D R A U L I C  
F
E E D  
O
P E R A T I O N  
I
N S T R U C T I O N S  
ControlArmOperation  
1. Engage the PTO. Bring the chipper up to operating speed. See the  
operationsectionforstarting, operation, andstoppinginstructions.  
Pleasereadand  
followallsafety  
2. Engage the hydraulic feed by moving the control arm as shown in figure  
11 below. The feed rate increases as the arm is moved in the forward  
direction.  
instructions in this  
manual.Failureto  
operatethechipperin  
accordancewiththe  
safetyinstructions  
MAYRESULTIN  
3. Feed the branch (up to eight inches in diameter).  
4. Reverse the feed by moving the control arm in the reverse direction if the  
chipperjams. Removethebranchandrotateitbeforereinsertingitintothe  
chute.  
PERSONALINJURY!  
Neutral  
Reverse  
Forward  
FeedControl  
Lever  
Figure11  
HydraulicSchematic  
Partslistedonpage28.  
PN-51210 (Rev. 7/98)  
23  
H
Y D R A U L I C  
F
E E D  
M
A I N T E N A N C E  
HydraulicFeedMaintenance  
NOTE:Checkthereservoirdailyforproperfluidlevel,thepresenceof  
water(notedbyacloudytomilkyappearanceorfreewaterinbottomof  
reservoir),andrancidfluidodor(excessiveheat).  
The hydrostatic pump normally does not require regular fluid changes.  
Change the system filter at 250 hour or annual intervals. Change the fluid  
and filter and clean the system if the fluid becomes contaminated with  
foreign matter (water, dirt, grease, etc.) or if the fluid has been subjected to  
temperature levels greater than the recommended maximum.  
There is a greaseable bearing on each side of the main jack shaft on the  
main hydraulic feed housing. Grease periodically.  
HydrostaticPumpTroubleshooting  
ProbableCause  
SuggestedRemedy  
Symptom  
Contactyourdealeror  
factoryservice  
Willnotattainnormalfeedrate.  
Enginenotoperatingat  
correct speed.  
Repairenginegovernor.  
Repair control linkage.  
Repair bypass valve.  
Control linkage damaged or  
binding.  
departmentBefore  
servicingorrepairing  
anyofthehydrostatic  
feedcomponents(pump,  
motor,and/orrelief  
valve).Warrantyon  
theseitemsmaybevoid  
withoutprior  
Bypass valve stuck partially  
open. (Probleminone  
direction only.)  
Removeforeignmaterialfrom  
valve.  
Willnotfeedwhencontrolarm  
ismoved.  
Control linkage damaged or  
notconnected.  
Repair or reconnect control  
linkage.  
Drive between engine and  
pumpdamaged.  
Repair drive (replace broken  
belt, repair sheared key, re-  
pair splined coupling, etc.).  
Refillreservoir. Purgeairfrom  
transmission.  
authorization.  
Pumplowonfluid.  
Feed rate is sluggish under  
load.  
Loosedrivebeltbetween  
engineandpump.  
Pumplowonfluid.  
Tension drive belt (replace if  
necessary).  
Refillreservoir. Purgeairfrom  
transmission if necessary.  
Drainfluidfromreservoirand  
unit, replace filter element,  
and refill with new fluid.  
Large amount of water in hy-  
draulicfluid(evaporateswhen  
hot, resultinginlowfluidlevel).  
Hydraulic Feed will not pull in  
logs over 4" in diameter, or  
continuously stalls or stops.  
Hydraulicsystemoverloading  
and causing system to go  
over relief  
Check relief pressure in sys-  
tem with a pressure gauge  
ratedto2500psi. (Systemset  
by factory at 1750 psi.)  
PN-51210 (Rev. 7/98)  
24  
T
R O U B L E S H O O T I N G  
Troubleshooting  
Problem  
Probable Cause  
Suggested  
Remedies  
Reference  
1. Rotordoesnotturn  
a) Obstructed  
discharge.  
a) Usebranchor  
similarobjectto  
cleardischarge.  
b) Clearrotor.  
ServiceandMaintenance  
b) Pluggedrotor.  
2. Hardtofeedchipper  
orexcessivepower  
neededtochip  
a) Obstructed  
discharge.  
a) Usebranchor  
similarobjectto  
cleardischarge.  
ServiceandMaintenance  
ServiceandMaintenance  
b) Dullchipperblades.  
c) Improperblade  
clearance.  
b) Sharpenblades.  
c) Adjustclearance.  
3. Chipperrequires  
excessivepoweror  
stalls  
a) Obstructed  
discharge.  
a) Usebranchor  
similarobjectto  
cleardischarge.  
b) Clearrotor,feed  
materialinto  
b) Pluggedrotor.  
shreddermore  
slowly.  
c) Greenmaterialwill  
notdischarge.  
c) Alternatelyfeeddry  
material,orallow  
materialtodry.  
4. Drivebelts  
squealingor  
smoking  
a) Pluggedrotor.  
b) Looseorwornbelts.  
a) Clearrotor.  
b) Adjustbelttension  
orreplacebeltsif  
needed.  
ServiceandMaintenance  
5. PTO will not turn or  
hasslowRPM's  
a) PTOshaftnot  
engagedontractor.  
b) PTOshaftloose.  
a) EngagePTO.  
ServiceandMaintenance  
ServiceandMaintenance  
b) Checkall  
connectionsand  
repairifneeded.  
6. Vibrationwhile  
running  
a) Driveshaftvibration.  
a) Checkdrivebelts  
andpulleysforbad  
orwornspots.  
CheckPTOshaftfor  
wear.  
b) Rotoroutof  
balance.  
b) Inspectrotorfor  
brokenormissing  
chipperbladesand  
paddles. Repairif  
needed.  
c) Checkrotortoseeif  
itwobbles.  
d) Checktoseeifrotor  
isassembled  
correctly.  
PN-51210 (Rev. 7/98)  
25  
C
H U T E A N D  
R
O T O R  
A
S S E M B L Y  
P
A R T S  
L
I S T  
ChuteandRotorAssemblyPartList  
No. Part No.  
Description  
Qty. No.  
27.  
Part No.  
51514  
51311  
51312  
51310  
51484  
51489  
3379  
Description  
Qty.  
1
Grease Zerk 1/4" Drive Ball  
Spring, LockCompression  
Decal, Discharge  
1. 51458  
2. 51474  
3. 51459  
4. 51460  
5. 51464  
6. 51461  
7. 51462  
8. 51463  
9. 51682  
51982  
Disk, Chipper  
Collar, Chipper Lock  
1
1
4
4
1
1
1
1
1
1
1
1
1
2
2
1
1*  
1*  
1
1
1
2
1
1
1
1
2
28.  
29.  
30.  
31.  
32.  
33.  
34.  
35.  
36.  
37.  
38.  
39.  
40.  
41.  
42.  
43.  
44.  
45.  
46.  
47.  
48.  
49.  
50.  
51.  
52.  
53.  
54.  
55.  
1
2
Blade, Chipper  
Bearing, 1-3/4 4 Bolt Flange  
Shaft, Chipper Top Pivot  
1
Paddle, Big Chipper  
1
Weldment, ChipperRotorShaft  
Plate, ChipperBottom  
Base, ChipperChute  
Strip, Flap Retainer  
1*  
3
Bolt, 1/2 x 1-1/2" GR5 Hex Capscrew  
SerialNumberDecal  
N/A  
1
BearingBracket, Right  
Decal, Woods8000Chipper  
Decal, Woods8100Chipper  
51301  
51261  
3699  
854  
Cap, LargeShaft  
1
THD Stud 1/2"-13 X 3" LG, B7, ZP  
Bolt, 1/2 X 2" G5 Hex Capscrew, ZP  
Washer, 1/2" Flat ZP (56PC/LB)  
Nut, 1/2CenterLocknut  
2
14  
6
10. 51506 Assy, Top Housing (#23,29, 34, 55 Incl.)  
11. 51507 Assy, Chipper Chute (#21 Included)  
12. 51557 Assy, Chipper Discharge (#29 Included)  
765  
30  
2
1093  
58782  
12169  
2290  
565  
Nut, HexNutNC, ZP  
13. 51467  
14. 51468  
15. 51469  
16. 51472  
17. 51473  
18. 51470  
19. 51471  
20. 51554  
21. 51373  
22. 51374  
23. 51375  
24. 51361  
25. 51284  
26. 12650  
Ring, DischargeSpacer  
Ring, DischargeClamp  
Lever, DischargeLock  
Angle, FlapAnchor  
Screw, 1/2 X 2" FLT HD SKT  
Bolt, 3/8 X 1-1/4" HHCS GR5 ZP  
Bolt, 3/8 X 2-1/2 GR5 Hex HHCS ZP  
Washer, 3/8" FLT ZP-140PC/LB  
Locknut, 3/8" NYL Insert, NE, ZP  
Bolt, Carr 3/8" X 1-1/2" GR5 NC, ZP  
Bolt, 5/16 X 2-1/2" G5 HX CAP ZP  
Washer, 5/16" FLT ZP (195PC/#)  
Locknut, 5/16NYL, NC, TYPNE, ZP  
Bolt, 3/8" X 1" Carriage GR5 ZP  
Cotter Pin, 1/8 X 1.00 ZP  
8
12  
1
24  
25  
10  
1
Flap, Chipper Chute  
Weldment, Dis. LockPin  
Tube, Discharge Lock Pivot  
Deflector, BlowerDischarge  
Danger, Decal  
28093  
51239  
1059  
4378  
71061  
6697  
3597  
639  
1
1
Decal, MadeinUSA  
Decal, OperatingInstructions  
DangerDecal  
4
3
Bolt, 1/2 X 2-1/2" Hex HD  
SpoutKnob, 5/16-18  
6
Decal, AccessCover  
Screw, #6 x 1/2" Drive  
51270  
58776  
58775  
2
Spacer, Anvil  
1
Decal, CheckBolts  
1
*Notusedonhydraulicfeedmodels  
ServiceAccessories  
Part#  
Description  
51222  
Chipper blade kit for PTO and towable models.  
Includesfourchipperbladesandreplacementboltsandnuts.  
51315  
57835  
Set of three matched belts for PTO model  
French Safety Decal Kit  
PN-51210 (Rev. 7/98)  
26  
C
H U T E A N D  
R
O T O R  
A
S S E M B L Y  
D
I A G R A M  
ChuteandRotorAssemblyDiagram  
PN-51210 (Rev. 7/98)  
27  
C
H I P P E R  
Chippe
Chippe
No. Part No.  
1. 51505  
2. 51465  
3. 51466  
4. 51475  
5. 51570  
6. 51273  
7. 81286  
8. 51314  
9. 51234  
HitchSupportWeldment  
Spacer, RH  
15.  
16.  
17.  
18.  
19.  
20.  
21.  
22.  
Pin, Top Link 3/4 X 4-1/2" LG  
Pin Lynch 7/16 X 5/8"  
1
1
2
1
1
1
1
1
51280  
51276  
51281  
51316  
51367  
51310  
51483  
51481  
1
3
Decal, 540PTODanger  
Driveshaft, 540 PTO Chipper  
Spring, Ext. 3/4" OD  
1
Bearing, 2 BLT FLG 1-1/2" Bore  
Pulley, Idler 5" X 2.50"  
Sheave, 3B13.6SK  
Sheave, 3B4.8SD  
1
1
Bearing, 1-3/4 4 Bolt Flange  
Weldment, LeftBearingBracket  
Weldment, LowerBeltGuard  
2
1
10.  
11.  
51224  
51315  
BushingSK1.5  
1
Belt, BX 64 (Matched Set of 3)  
PN-51210 (Rev. 7/98)  
28  
H I P P E R  
B
A S E  
A
S S E M B L Y  
26. 51419  
27. 51480  
28. 51490  
29. 51503  
30. 51504  
Description  
Qty.  
/2" Flat ZP (56PC/LB)  
1/2" Center Lock  
25  
1
/8"FLT ZP-140PC/LB  
/8" NYL Insert, NE, ZP  
Bolt, 5/16 X 1" GR5 HHCS NC ZP  
Washer, 5/16" FLT ZP (195PC/#)  
Locknut, 5/16" NYL, NC, TYP NE, ZP  
Bolt, CARR 1/2 X 1-1/2" GR5, ZP  
Bolt, CARR 1/2 X 1-1/2" GR5 ZP  
Bolt, 3/8 X 3-1/4" HXHD GR5 ZP  
DangerDecal  
21  
26  
10  
19  
5
38. 14562  
JointShieldWeldment  
Weldment,IdlerArm  
1
1
39.  
40. 71061  
41. 839  
4378  
Cover, HoseAccess  
1
Shield, Shaft  
1
2
Plate, Spring Anchor  
1
42. 12735  
43. 12169  
44. 51361  
45. 58777  
46. 15131  
2
31.  
32.  
33.  
3379  
3699  
1637  
Bolt 1/2 X 1-1/2 GR5 Hex Capsw Zp  
Bolt, 1/2 X 2 GR5 Hex Capscrew Zp  
Bolt, 1/2 X 3-1/2 GR5 HCS ZP  
9
1
10  
1
1
Wldmt,PickupSprocket  
1
Screw, 5/16" x 5/8" Cup PT  
PN-51210 (Rev. 7/98)  
29  
1
H
Y D R A U L I C  
Hydraul
PN-51210 (Re
30  
31  
H
Y D R A U L I C  
F
E E D  
P
A R T S  
L
I S T  
HydraulicFeedPartsList  
No. Part No.  
1. 51476  
2. 51477  
3. 51479  
4. 51478  
5. 51486  
6. 51487  
7. 51256  
8. 51522  
Description  
Weldment, RollerSupport  
Weldment, TopGrabRoller  
Weldment, Roller Slide  
Bearing, Roller Slide  
Weldment, TopRollerCover  
Shield, Coupler  
Qty.  
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
No. Part No.  
Description  
Qty.  
1
42.  
43.  
44.  
45.  
46.  
47.  
48.  
49.  
50.  
51.  
52.  
53.  
54.  
55.  
56.  
57.  
58.  
59.  
60.  
61.  
62.  
63.  
64.  
65.  
66.  
67.  
68.  
69.  
70.  
71.  
72.  
73.  
74.  
75.  
76.  
77.  
78.  
79.  
80.  
81.  
82.  
83.  
84.  
85.  
51369  
51373  
1686  
Spring, Drift Cutter 1-1/4"LG  
Decal, Danger  
2
Cotter Pin, 1/16 X 3/4" Steel ZP  
Screw, #10 X 3/4" Phillips  
1
35709  
51252  
5337  
2
Locknut, #10NYLInsertTPNEZP  
Bolt, 1/4 X 1/2" HCS G5 ZP  
Bolt, 1/2" x 1-3/4" Carriage GR5 ZP  
Locknut, 5/16" NYL, NC, TYP NE, ZP  
2
4
Coupler 1-1/4" Shaft  
Weldment, ControlPivot  
Weldment,ControlArm  
Weldment,CableAnchor  
Weldment, FeedControlLever  
Spacer, Idler Pivot  
51248  
71061  
51591  
51589  
24576  
51239  
21757  
28093  
3632  
6
9
9.  
51493  
Washer, 5/16" SAE FLT ZP (195PC/#) 11  
10. 51494  
11. 51495  
12. 51393  
13. 51496  
14. 51497  
15. 51498  
Clip, Hairpin  
2
4
8
Bolt, 1/2 X 1-3/4" GR5 Hex CPS ZP  
Bolt, Carr 3/8 X 1-1/ 2" GR5 NC ZP  
Strip, Control Tie Rod  
Weldment,PumpControlArm  
Angle, CableAttachment  
Bracket,PumpMount  
Strap Reservoir  
Washer, 3/8" SAE FLT ZP-140 PC/LB 41  
Locknut, 3/8" NYL Insert, NE, ZP  
Washer, 5/8" SAE Flat ZP(37PC/LB)  
Decal, Oil Level  
36  
8
16.  
51485  
58780  
58781  
14562  
6697  
1
17. 51492  
18. 51491  
19. 51510  
20. 51240  
21. 51507  
22. 51432  
23. 51304  
24. 51317  
51262  
Decal, Oil  
1
Weldment, ReservoirSupport  
Cover, Reservoir Base  
Bolt, 5/16" x 2" GR5 HCS ZP  
Assy, ChipperChute(Inc. #43)  
Spacer, 0.75X0.620  
Sheave, 1B5.2SDS  
Pump, Hydrostatic  
Bolt, 5/16 X 1" GR5 HHCS NC ZP  
Bolt, 3/8 X 1" CRG  
2
5
839  
Bolt, 3/8 X 1" GR5 Hex Capscrew ZP 12  
3597  
Pin, 1/8 X 1" Cotter  
Nut, 3/8" Hex NC ZP  
2
1
835  
51236  
12169  
3231  
Spring, Extension  
2
Bolt, 3/8 X 1-1/4" Hex Hd  
Bolt 3/8 X 2" GR5 Hex Capscrew ZP  
Bolt, 1/2 X 2" GR5 Hex Capscrew ZP  
Nut, 1/2" Center Locknut ZP  
Washer, 1/2" Flat, ZP, (26PCS/LB)  
Hinge, Extension  
2
Kit Hydrostatic Pump Seal  
Motor, 45Cu. In. Hydraulic  
Kit White Motor Seal  
Valve, Crossover Relief  
Kit, Relief Cartridge Seal  
Kit, 2000 PSI Relief Shim  
Filter, Spin-on  
2
25. 51318  
51263  
3699  
4
765  
12  
12  
1
26. 51319  
51271  
854  
51513  
63013  
51264  
3912  
51287  
Key, 5/16" Sq X 2  
2
27. 51320  
28. 51321  
29. 51306  
30. 51330  
31. 51237  
32. 51254  
33. 51380  
34. 51329  
35. 51245  
36. 51242  
37. 51768  
38. 51246  
39. 51238  
40. 51365  
41. 51366  
Key,5mmSqX25mm  
1
Tank, Oil Reservoir  
Key, 3/8 X 1/4"  
1
Sheave, 1B3.6SH  
51294  
51302  
51325  
51392  
51391  
51300  
51265  
51327  
51328  
51324  
51258  
51512  
Adapter Oring to Flare  
2
Bushing, 1.75SDS  
Adapter Oring to Flare  
6
Bushing,15mmSH  
Reducer Bushing 3/4 X 1/2" NPT  
Elbow, 90Deg, 2024-8-6  
Elbow, 90Deg, 2062-6-6  
HydHSAssy2X/-10MJICSWVL  
Eyebolt, 1/2 x 2  
2
Bearing, 1-1/4" Dia. 2 Bolt Flng.  
Bearing, Side Flng. Mount, 5/8"  
Cable, Hydrostat Control  
Cable Pivot Pin  
2
1
2
4
ClevisAssembly  
Hyd. HoseAssy, NoneX-6JIC  
Hyd. HoseAssy. 2X-6JIC  
Adapter, Oring to Flare  
2
Cable ClampShim  
1
Cable Clamp  
1
Belt, BX43  
Hy-Hose-Asy-10FM90JICSW/-10FM  
Tray, Chute Extension  
2
Detent Ball  
1
Detent Spring  
PN-51210 (Rev. 7/98)  
32  
S
P E C I F I C A T I O N S  
Specifications  
Model8000  
87"  
Model8100  
87"  
Height(todischarge)  
FrameWidth  
FrameLength  
OverallSize  
38"  
38"  
36"  
36"  
45" x 47" x 90"  
32" x 36"  
0.25"+0.38"Steel  
SelfFeed  
Blower  
45" x 47" x 90"  
32" x 36"  
0.25"+0.38"Steel  
Hydraulic  
Blower  
ChuteSize  
FrameMaterial  
FeedSystem  
Discharge  
8"  
8"  
MaximumChipperCapacity(dia.)  
ChipperBladeQty. (*=toolsteel)  
RotorSpeed  
4ToolSteel  
1500RPM  
4ToolSteel  
1500RPM  
30" Dia. x 1.25"  
275lbs.  
30" Dia. x 1.25"  
275lbs.  
RotorSize  
RotorWeight  
1.75"  
1.75"  
RotorShaftDiameter  
Belt  
Belt  
DriveType  
BX64, (3)  
BX64, (3)  
Belt Size (qty.)  
SplineSize  
1.375Diameter(6Spl)  
1.375Diameter(6Spl)  
TopTube  
TopTube  
Discharge  
8"Diameter  
8"Diameter  
DischargeOpening  
Specificationsaresubjecttochangebecauseofdesignmodifications.  
PN-51210 (Rev. 7/98)  
33  
Warranty  
Woods warrants each new Woods products to be free from defects in material and  
workmanship. This warranty is applicable only for the normal service life expectancy of the  
machine or components, not to exceed twelve consecutive months from the date of delivery  
of the new Woods product to the original purchaser.  
Genuine Woods replacement parts and components will be warranted for 90 days from date  
of purchase, or the remainder of the original equipment warranty period, whichever is longer.  
Under no circumstances will it cover any merchandise or components thereof, which, in the  
opinion of the company, has been subjected to negligent handling, misuse, alteration, an  
accident, or if repairs have been made with parts other than those obtainable through Woods.  
The company in no way warrants engines, batteries, tires or other trade accessories since  
these items are warranted separately by their respective manufacturers.  
Our obligation under this warranty shall be limited to repairing or replacing, free of charge to  
the original purchaser, any part that in our judgement shall show evidence of such defect,  
provided further that such part shall be returned within thirty (30) days from date of failure to  
Woods, routed through the dealer and distributor from whom the purchase was made,  
transportation charges prepaid.  
This warranty shall not be interpreted to render us liable for injury or damages of any kind or  
nature to person or property. This warranty does not extend to loss of crops, loss because of  
delay in harvesting, or nay expense or loss incurred for labor, supplies, substitute machinery,  
rental or for any other reason.  
Except as set forth above, WOODS SHALL HAVE NO OBLIGATION OR LIABILITY OF  
ANY KIND ON ACCOUNT OF ANY OF ITS EQUIPMENT AND SHALL NOT BE LIABLE  
FOR SPECIAL OR CONSEQUENTIAL DAMAGES. WOODS MAKES NO OTHER  
WARRANTY, EXPRESS OR IMPLIED, AND, SPECIFICALLY, WOODS DISCLAIMS ANY  
IMPLIED WARRANTY OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR  
PURPOSE. SOME STATE OR PROVINCES DO NOT PERMIT LIMITATIONS OR  
EXCLUSIONS OF IMPLIED WARRANTIES OR INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE LIMITATIONS OR EXCLUSIONS IN THIS WARRANTY MAY NOT  
APPLY.  
This warranty is subject to any existing conditions of supply which may directly affect our  
ability to obtain materials or manufacture replacement parts.  
Woods reserves the right to make improvements in design or changes in specifications at any  
time, without incurring any obligations to owners of units previously sold.  
No one is authorized to alter, modify, or enlarge this warranty nor the exclusions, limitations  
and reservations.  
PN-51210 (Rev. 7/98)  
HEALTHWARNING  
GASOLINE, DIESEL, AND  
OTHER PETROLEUM PRODUCTS  
Harmful or fatal if swallowed.  
Long-term exposure to vapors has caused cancer in  
laboratory animals.  
• Avoid prolonged breathing of vapors.  
• Keep face away from nozzle and gas tank/container  
opening.  
• Never siphon by mouth.  
Failure to use caution may cause serious injury or illness.  
WARNING  
CHEMICALS KNOWN TO THE STATE OF CALIFOR-  
NIA TO CAUSE CANCER, BIRTH DEFECTS, OR  
OTHER REPRODUCTIVE HARM ARE FOUND IN  
GASOLINE, DIESEL, CRUDE OIL, AND MANY OTHER  
PETROLEUM PRODUCTS AND THEIR VAPORS, OR  
RESULT FROM THEIR USE.  
READ AND FOLLOW LABEL DIRECTIONS AND USE  
CARE WHEN HANDLING OR USING ALL PETRO-  
LEUM PRODUCTS.  
ENGINE EXHAUST FROM THIS PRODUCT CON-  
TAINS CHEMICALS KNOWN TO THE STATE OF CALI-  
FORNIA TO CAUSE CANCER, BIRTH DEFECTS, OR  
OTHER REPRODUCTIVE HARM.  

Tekkeon MP1250 User Manual
Tascam CD RW5000 User Manual
Samsung SCH 210 User Manual
Rosewill GIGABIT RC411 User Manual
RCA GES050 User Manual
Pelco Computer Drive DVR5KUP 250 500 User Manual
Panasonic SC AK403 User Manual
Panasonic DVCPRO AJ PCS060G User Manual
Oregon JM889NA User Manual
Nokia PUSHTOTALK SERIES 40 User Manual