D00864010A
»
CD-01U/CD-01UPro
CD PLAYER
OWNER’S MANUAL
˛
Important Safety Instructions
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
• Do not expose this apparatus to drips or splashes.
• Do not place any objects filled with liquids, such as
vases, on the apparatus.
• Do not install this apparatus in a confined space such as
a book case or similar unit.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
• The apparatus draws nominal non-operating power from
the AC outlet with its POWER switch in the off position.
• The apparatus should be located close enough to the AC
outlet so that you can easily grasp the power cord plug at
any time.
7 Do not block any ventilation openings. Install in accor-
dance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
• An apparatus with Class I construction shall be connect-
ed to an AC outlet with a protective grounding connec-
tion.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the appara-
tus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-
over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
TASCAM CD-01U/CD-01UPro
3
Safety Information
This product has been designed and manufactured
according to FDA regulations "title 21, CFR, chapter
1, subchapter J, based on the Radiation Control for
Health and Safety Act of 1968", and is classified as a
class 1 laser product. There is no hazardous invisible
laser radiation during operation because invisible
laser radiation emitted inside of this product is com-
pletely confined in the protective housings.
The label required in this regulation is shown 1.
CAUTION
• DO NOT REMOVE THE PROTECTIVE HOUSING
USING A SCREWDRIVER.
• USE OF CONTROLS OR ADJUSTMENTS OR PER-
FORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZ-
ARDOUS RADIATION EXPOSURE.
• IF THIS PRODUCT DEVELOPS TROUBLE, CON-
TACT YOUR NEAREST QUALIFIED SERVICE PER-
SONNEL, AND DO NOT USE THE PRODUCT IN
ITS DAMAGED STATE.
Optical pickup:
Type:
KSM-900AAA
Manufacturer: SONY Corporation
Laser output: Less than 0.5 mW on the objec-
tive lens
Wavelength: 775 to 815 nm
4
TASCAM CD-01U/CD-01UPro
Table of contents
1 - Introduction
7 - Advanced operations
Auto Cue ......................................................18
Auto Ready .................................................18
Resume .........................................................18
Call ....................................................................18
Incremental play ..................................................19
Repeat playback .........................................19
A to B repeat playback ...............................19
Intro check .......................................................20
Output in monaural ..............................................20
Power on play ................................................20
Pitch control ..................................................20
Changing the playback speed without changing
the key (Key original) ...................21
Supplied accessories ..................................6
Environmental considerations .....................6
Some notes and precautions ..........................6
Beware of condensation .....................6
Back up memory .................................6
Rack - mounting the unit .......................7
Handling of compact discs ...........................7
2 - Remote control unit
Some notes and precautions .......................8
Batteries ........................................................8
Inserting batteries .....................................8
3 - Connections
Program playback .......................................21
Editing a programmed track ......................21
Adding a track to the program .................21
Deleting a programmed track ....................22
Fade in and fade out .......................................22
Relay play ................................................22
Time display switching ..............................23
End of disc/track warning ......................................23
Eject block .............................................23
Fader start/Event start ..............................23
Fader start/stop .....................................23
Event start ...........................................24
Restoring factory default settings ...................24
External parallel control ........................................24
Audio equipment .......................................9
Connecting analog audio equipment ...........9
Connecting digital audio equipment ..........9
Power source ................................................9
4 - Features and their functions
Front panel ..................................................10
Display .......................................................11
Rear Panel ...................................................12
Remote Control Unit ..................................12
5 - Menu operation
Menu configuration ...................................14
Menu operation .........................................14
Operation basics .........................................14
8 - Specifications
Specifications ........................................................25
Dimensional drawing ................................26
Error Messages ...........................................26
6 - Playback
Discs for playback .......................................15
About finalization .......................................15
For MP3 CDs ............................................15
Playback modes ..........................................16
Basic playback operation ...........................16
Using headphones .......................................16
Track selection ............................................16
Selecting by track number .......................17
Search ..........................................................17
Frame search ...................................17
TASCAM CD-01U/CD-01UPro
5
Œ
1 - Introduction Environmental considerations
Thank you for your purchase of the TASCAM CD-
01U/CD-01U Pro CD player.
CD-01U/CD-01U Pro, as well as the operation of its
many useful and convenient functions. After you have
finished reading this manual, please keep it in a safe
place for future reference.
Before connecting and using the unit, please take time
to read this manual thoroughly to ensure you under-
stand how to properly set up and connect the
Supplied accessories
In addition to this manual, the CD-01U/CD-01U Pro
have been packed with the following:
Should any of these items be missing, or if you
encounter any damage, please contact your TASCAM
supplier.
≠ RC-01UC remote control unit
≠ 2 AAA batteries
≠ Power cord
≠ Rack-mounting kit
≠ Warranty document
This unit was packed in its carton with special materials
in order to prevent any damage during shipment.
Please save the carton and packing materials in the
event you need to transport the unit in the future.
Environmental considerations
The CD-01U/CD-01U Pro may be used in most places,
but to maintain top performance and prolong operating
life, do not place it in the following locations.
≠ Near heating or air conditioning vents, or in very hot or
cold places
≠ Places with high humidity or poor ventilation
≠ Next to tuners, televisions or video decks, as this
≠ On an unsteady surface, or where there is frequent
could cause noise or affect video images
vibration or resonance
≠ Near a window or where it can be exposed to direct
sunlight
Some notes and precautions
Connect the CD-01U/CD-01U Pro only to the specified
power source.
Clean only with a dry cloth. Do not use benzene, paint
thinner or other agents that could damage the surface.
Dust or grime on the top cover can be removed with a
soft cloth lightly moistened with a diluted mild detergent
solution.
When unplugging the cord, grasp the plug itself.
Beware of condensation
If the unit is moved from a cold to a warm place, or
used after a sudden temperature change, condensation
inside the unit may occur, resulting in moisture on the
internal mechanism or an inserted disc, thus impairing
proper operation.
Should this occur, leave the player turned on for one or
two hours so that the condensation can evaporate
before you begin operation.
Also, please remove all discs from the unit if it will be
moved, or not operated for an extended period of time.
Backup Memory
Even when the power is turned off, the following set-
tings are retained.
≠ Playback mode
≠ Time display mode
≠ Auto ready ON/OFF
≠ Auto cue ON/OFF
≠ Pitch control value
≠ All menu settings
6
TASCAM CD-01U/CD-01UPro
Œ
1 - Introduction Environmental considerations
Rack-mounting the unit
Use the rack-mounting kit to mount the unit in a
standard 19-inch equipment rack, as shown below.
Remove the feet of the unit before mounting.
If you are mounting the unit in a rack, leave 1U of
space above it and 10cm (4 in) or more of space at
the rear. The CD-01U/CD-01U Pro can be mounted
in any angle between 0 to 90 degrees.
SeeEnvironmental considerationson the previous page.
Handling of compact discs
The CD-01U/CD-01U Pro have been designed for the
≠ Keep discs away from direct sunlight, and places of
high heat and humidity. If left in such places, warping
playback of CD-DA format discs and MP3 files record-
ed in ISO9660 format. In addition to ordinary 5-inch and
3-inch CDs, it can also play properly recorded CD-R
and CD-RW discs.
could result.
≠ Do not affix any labels or stickers to the label side of
the disc. Do not write on the disc with a ballpoint
pen.
When removing a CD from its case, press down on the
center of the disc holder to free the CD, then lift the disc
out, holding it carefully by the edges.
≠ Please do not insert discs that have adhesive remain-
ing from tape or stickers that have been removed. If
they are inserted into the player, they could stick to
the internal mechanism, requiring removal by a tech-
nician.
≠ Removing a disc
≠ Hold the CD like this
≠ Only use circular compact discs. Avoid using non-cir
cular promotional, etc. discs.
≠ The CD-01U/CD-01U Pro cannot play unfinalized
CD-R/RW discs.
≠ Do not use a C-thru disc.
≠ Avoid getting fingerprints on the signal side (opposite
the label side). When cleaning, wipe gently with a soft
cloth from the center towards the outside edge. Dust
and grime may cause skipping, so keep discs clean
and store them in their cases when not being played.
The unit does not support a C-thru disc. Therefore,
you may not be able to insert a C-thru disc or may
not be able to remove a C-thru disc that has been
successfully inserted to the unit.
In the latter case, try to press the DISPLAY and
EJECT keys simultaneously, which may solve the
problem.
≠ Do not use the DualDisc. DualDisc is two-sided play-
back only discs. Insertion or ejection of a DualDisc
into/from CD-01U/CD-01U Pro is likely to cause
scratches to the surface of the DualDisc. Scratched
discs may not play in CD products.
≠ Do not use any record spray, anti-static solutions,
benzene, paint thinner or other chemical agents to
clean CDs as they could damage the delicate playing
surface.
A DualDisc may not play in CD-01U/CD-01U Pro and
a DualDisc could get stuck in and may not be able to
be removed from the CD-01U/CD-01U Pro.
≠ Discs should be returned to their cases after use to
avoid serious scratches that could cause the laser
pickup to skip.
TASCAM CD-01U/CD-01UPro
7
2 - Remote control unit
Some notes and precautions
Batteries
≠ When the remote control will not be used for an
extended period of time, please remove the batteries
to prevent the possibility of battery acid leakage
which could damage the unit.
If batteries are used improperly, or if leakage or break-
age occurs, the unit will not function.
Please observe the cautions indicated on the batteries
and their packaging to ensure proper usage.
Should leakage occur, remove and discard the bat-
teries, and wipe the battery case thoroughly with a
cloth.
≠ Confirm + and - polarity and follow the indications
when inserting new batteries into the remote control.
Avoid getting the battery liquid on the skin. After
cleaning, replace with new batteries.
≠ Do not use old and new batteries together.
≠ Even if the battery is the same size, the voltage may
≠ The remote control functions by using an infrared
light signal. When using the unit to control the CD-
01U/CD-01U Pro, other devices that are turned on
could be operated by its signal.
differ.
Do not use batteries of different specifications
together.
≠ Do not attempt to recharge batteries that are non-
≠ If the range of remote operation becomes smaller, or
commands do not always function properly, the bat-
teries have become weak and should be replaced.
Always replace both batteries with new batteries of
the same type.
rechargeable.
≠ Do not open or disassemble batteries, throw them
into a fire or put them in water.
Inserting batteries
≠ Point the remote control to the remote sensor on the
main unit.
1. Open the lid.
Do not obstruct the path between the remote control
and the remote sensor.
2. Confirm +/- polarity, and insert two AAA batteries.
3. Close the lid.
7 m
8
TASCAM CD-01U/CD-01UPro
3 - Connections
Before connecting the CD-01U/CD-01U Pro to other units, please read their operation manuals thoroughly to ensure
proper connection. Turn the power on only after all connections have been made.
Audio equipment
Connecting analog audio equipment
Connecting digital audio equipment
Connect analog stereo amplifiers, mixers and recorders
to the analog line outputs.
Digital stereo amplifiers, mixers and recorders can be
connected through the optical digital output terminal.
Power source
≠ Connection cables are not supplied with this unit.
≠ Do not bundle the pin connection cords with the
power cord as noise or diminished sound quality
could result.
This unit has been designed to operate on the specified
power voltage only.
Do not plug the power cord into outlets of any other
voltage.
TASCAM CD-01U/CD-01UPro
9
4 - Features and their functions
Front panel
1 POWER switch
0 DISPLY key
2 Disc slot
Pressing this key changes the time mode on the dis-
play. Even when the power is turned off, the time
mode is retained.
Insert CD into the slot, label side upwards.
3 Remote signal sensor
4 EJECT key
When in menu mode, exits the menu mode.
q SHIFT key and indicator
Ejects a disc. This key cannot be used when Eject
Block is on and disc is being played back.
Turns the shift mode on and off. When in shift mode,
the indicator lights and other keys have shift func-
tions which indicated under the keys.
5 Display
The display is used to show the current status of the
unit, as well as the current menu settings.
Pressing this key again exits shift mode.
w ¥?π (JOG) key and indicator
6 PITCH (MENU) control knob
Changes the playback mode between playback and
pause.
Push this control to turn the pitch control function on
or off. When it is on, pitch value is shown on the
Display, and pitch can be controlled +/- 12.5%.
Even when the power is turned off, the pitch control
ON/OFF setting is retained.
The indicator stays on solid in playback mode and
flashes in pause mode.
When playback is paused and SHIFT indicator is lit,
frame accurate search can be performed using with
the PITCH knob.
When in shift mode, functions as the menu dial when
rotated, and as the ENTER key when pushed.
e CALL (PLAY MODE) key
When playback is paused and SHIFT indicator is lit,
frame accurate search can be performed using with
this knob.
Locates the playback to the last play start point.
When SHIFT indicator is lit, selects the playback
7 SKIP (INDEX/DIR SEARCH) keys
mode.
Use these to perform track searches.
r ª (INTRO CHECK) key
When SHIFT indicator is lit, searches the index
Use this key to stop playback.
(Audio CD discs) or directory (MP3 discs).
When Incremental Play is activated, pressing this key
pauses at the beginning of next track.
8 SEARCH (A.CUE, A.RDY) keys
Performs review or cue playback (search).
When in shift mode, enters Intro Check mode.
When in shift mode, selects the Auto Cue level or
turns the Auto Ready mode on and off.
t PHONES jack
Use a standard pair of stereo headphones, equipped
with a 1/4-inch plug, with this jack.
9 PHONES level control
Adjusts the headphone output level.
10
TASCAM CD-01U/CD-01UPro
4 - Features and their functions
Display
1TRACK indicator
8 REPEAT indicators
2 Track number display
Indicates the current repeat mode.
Shows the track number. In the menu mode, shows
the menu number.
9 PITCH indicator and pitch value display
When pitch control is activated, shows the pitch
3 MP3 indicator
value and PITCH indicator lights.
Lights when a MP3 CD-ROM disc is inserted.
4 INDEX/DIR indicator
In the menu mode, shows the menu parameters.
0 A.CUE indicator
Shows the index number (CD-DA) or directory
number (MP3).
Lights when Auto Cue function is turned on.
q A.RDY indicator
5 T and REMAIN indicators
Lights when Auto Ready function is activated.
When the time mode is set to remain time mode,
these indicators light.
w RELAY indicator
Lights when Relay Play mode is activated.
Total remain mode: Both T and REMAIN indicators
light.
e FADE indicator
Lights when Fade in/out is turned on.
Track remain mode: REMAIN indicator lights.
6 Time display
r MONO indicator
Lights when in Mono output mode.
This section is used to show time values, menu
information or messages.
t RESUME indicator
Lights when Resume mode is on.
y INCR indicator
Lights when Incremental Play is activated.
7 Play mode indicators
u KEY ORIGINAL indicator
Indicates the current playback mode.
RANDOM: Random playback mode
S: Single playback mode
Lights when Key Original function is turned on.
PGM: Programmed playback mode
TASCAM CD-01U/CD-01UPro
11
4 - Features and their functions
Rear panel
1 ANALOG OUTPUT terminals
5ANALOG OUTPUT (BALANCED) terminals (CD-
01U Pro only)
The analog line output terminals are for RCA pin
jacks. The maximum output level is +6 dBV.
The analog line output terminals are for XLR
connectors. The maximum output level is +20 dBu.
2 DIGITAL (OPTICAL) OUTPUT terminal
6DIGITAL (AES/EBU) OUTPUT terminal (CD-01U
Provides the digital audio signal in S/PDIF format.
This connector outputs the 44.1KHz digital signals
constantly even if pitch control is activated.
Pro only)
Provides the digital audio signal in AES/EBU format.
This connector outputs the 44.1KHz digital signals
constantly even if both control is activated.
3 CONTROL I/O (RS-232C) connector
This RS-232C interface allows control by a computer
or by other serial controllers. Consult your TASCAM
dealer the TASCAM web site for details of this port if
you wish to use it.
7CONTROL I/O (PARALLEL) connector (CD-01U
Pro only)
Parallel control from an external devices can be
performed.
4 RELAY IN/OUT jacks
8
IN
These jacks are used to perform the relay play
operation between two or more CD-01U/CD-01U
Pro, or perform the fader start or event start
operation.
Connect the power cable supplied with the CD-
01U/CD-01U Pro.
Remote Control Unit
1 EJECT BLOCK key
This turns the Eject Block mode on and off.
2 DISPLAY key
Pressing this key changes the time mode on the
display.
3 PLAY MODE key
This selects the playback mode. During selection, the
playback mode is indicated on the display in the
following manner.
Normal playback (in disc order): no indication
Single playback: S lights up
Program playback: PGM lights up
Random playback: RANDOM lights up
4 EJECT key
Press this to eject the disc. This key cannot be used
when Eject Block mode is on and the disc is being
played back.
12
TASCAM CD-01U/CD-01UPro
4 - Features and their functions
5 PITCH key +/- keys
o SEARCH keys
Use these keys to perform the pitch control function.
During playback or playback standby, press the key
continuously for review or cue playback (search).
6 KEY ORIG key
p INDEX/DIR SEARCH key
This turns the Key Original function on and off.
Use this key to select the index (Audio CDs) or
directory (MP3 discs).
7 A.CUE/DEL key
Sets the Auto Cue level.
During program input, the selected program number
track is deleted.
a JOG +/- keys
Pressing the key in pause mode performs the frame
accurate search.
8 A.RDY/INS key
s¥PLAY key
Turns the Auto Ready function on and off.
During program input, inserts a track into the
program list.
Press this key to start CD playback.
When incremental play function is activated, pressing
this key play start from the next track.
9 REPEAT key
dπ READY key
Turns the Repeat Play mode on and off.
Pressing and holding this key for one second or
more enters the Repeat A-B mode.
When this key is pressed during playback or while
stopped, enters standby mode.
0 INTRO CHECK key
f CALL key
Enters the Intro Check mode.
Locates the playback to the last play start point.
q MENU key
gª STOP key
Enters the Menu mode.
Use this key to stop playback.
When incremental play function is activated, pressing
this key pauses at the beginning of the next track.
w ENTER key
Confirms the menu options and confirms the settings
and editing on the menu.
e PREV key
Selects the previous menu option or setting on the
menu.
r NEXT key
Selects the next menu option or setting on the menu.
t Number keys
These are used to select track numbers.
y CLEAR key
During track number input, the track number is
cleared when this key is pressed.
u PGM key
Pressing this key enters the Program mode.
i SKIP keys
Use these keys to skip to the previous track or the
next track.
TASCAM CD-01U/CD-01UPro
13
5 - Menu operation
The various settings and editing operations possible
with the CD-01U/CD-01U Pro are performed through
menu options shown on the display. Among the many
menu setting options, some may be made directly using
the keys on the remote control.
No.
Menu
Function
Parameter
Manual reference
Page
Underlined values are fac-
tory default settings
01
02
03
KEY-0
Key Original
ON, OFF
Key Original
21
23
19
19
21
22
21
BLOCK
REPEAT
Eject Block
ON, OFF
Eject Block
Repeat Playback
A-B Repeat Playback
Program
OFF, ON, A-B
Repeat Playback
04
05
06
PROG
FADE
rogram operation
OFF, 0.5-10.0
OFF, ON, FDR
Program Playback
Fade In/Out
Relay Play
23
Fade In/Out
RELAY
Relay Playback
Fader/Event Start
Power on Play
Mono Output
Resume
07
08
09
10
TIMER
MONO
RESUME
EOM
ON, OFF
Power on play
Output in Mono
Resume
20
20
18
23
ON, OFF
ON, OFF
EOM Time
OFF, 5, 10, 15, 20,
EOM
25, 30, 35 sec.
Incremental Play
Pitch Step
11
12
13
14
15
INCR
ON, OFF
Incremental Play
Pitch Control
19
20
PITCH
RS232C
F-PRE
U-DATA
0.1, 0.5, 1.0 %
96, 192, 384
(SURE)
Baud rate setting
Factory Preset
User Data
Restoring the default setting
24
ON, OFF
ÆÆ
ÆÆ When digital output signal from the AES/EBU terminal is not received correctly on the other digital equipment , set
the user data to OFF then try again.
Operation basics
1 Press the PITCH knob on the front panel when
SHIFT indicator is lit or press the MENU key on the
remote control.
4 Use the PITCH knob on the front panel or
PREV/NEXT keys on the remote control to select the
setting value.
5 Press the PITCH knob on the front panel or ENTER
Menu No.
Menu
Parameter
key on the remote control.
Pressing the DISPLAY key on either the front panel or
the remote control exits the menu mode.
2 Use the PITCH knob on the front panel, or
PREV/NEXT keys or number keys on the remote
control to select the menu item.
3 Press the PITCH knob on the front panel or ENTER
key on the remote control.
14
TASCAM CD-01U/CD-01U Pro
6 - Playback
Discs for playback
The CD-01U/ CD-01U Pro can playback the types of
discs listed below.
≠ MP3 files recorded in ISO9660 format on CD-R and
CD-RW discs, and properly finalized.
≠ CD-R/RW discs that have not been finalized cannot
be played back. Make sure the disc has been prop-
erly finalized before loading into the player.
≠ Ordinary audio CDs available commercially (recorded
in CD-DA format).
≠ CD-R and CD-RW discs recorded in CD-DA format,
and properly finalized.
About finalization
Even if audio data is recorded onto a CD-R/RW disc, if
the TOC (table of contents corresponding to the record-
ed data) is not written on the disc after recording, the
disc cannot be played back on conventional CD play-
ers. Finalization is the process of writing the TOC on the
disc.
copy control CD discs as a means of protecting artist
copyrights. Some of these discs do not comply with
standard CD format specifications, and may not be able
to be played on this unit.
The CD-01U/CD-01U Pro can play back MP3 files
recorded in formats which conform to ISO9660 level 1,
level 2 and Joliet.
A number of record companies have released titles on
For MP3 CDs
CDs containing MP3 files can be played by the CD-
01U/CD-01U Pro with the following limitations on the
number of files and directories.
MP3 files are played as the order in the following diagram.
In this manner, playback is performed from the top level
directories.
Maximum number of directories: 254
Maximum number of MP3 files: 255
File format: MPEG 1 audio layer 3
Bit rate: 32kbps to 320kbps
Sampling frequency: 44.1KHz, Stereo
File extension: mp3, Mp3, mP3, MP3
The CD-01U/CD-01U Pro can only read the files in the
first session of a multi-session disc.
ID3 tag display for MP3 playback is not supported.
: Folder (Directory)
: MP3 File
TASCAM CD-01U/CD-01UPro
15
6 - Playback
Playback modes
There are four different playback modes. The mode
changes the playback mode in the following order:
selected is indicated on the display.
Cont ∑ Single ∑ Program ∑ Random
Normal (continuous) playback mode: no indication lamp
Single playback mode: S is lit
You can also select the playback mode pressing the
CALL/PLAY MODE key on the front panel when in
SHIFT mode.
Program playback mode: PGM is lit
Random playback mode: RANDOM is lit
While the mode can be changed from any playback
mode, the explanation in this manual will assume the
user is starting from the normal Continuous mode.
The playback mode can be selected using the PLAY
MODE key on the remote control. Pressing the key
Basic playback operation
1 Push the POWER switch to turn on the unit.
The display will indicate NO DISC.
back standby mode.
To resume playback, press the ¥?π key or the front
panel or ¥key on the remote control.
2 Insert a disc into the slot, label side upwards.
After a disc is inserted, the total playing time and
number of tracks will be displayed.
To remove the disc
Press the EJECT key on either the front panel or
remote control unit.
Do not force the disc into the slot, the CD-01U/CD-
01U Pro will pull the disc when partially inserted.
You can insert back a disc into the slot by pressing the
EJECT key or pull the disc and slot it in again.
3 Press the ¥?π key on the front panel or ¥ key on
the remote control unit.
The play indication will light up, and playback begins
from track 1. The number of the current track in play
is indicated on the display.
When Eject Block is activated, EJECT key cannot be
used when disc is being played back.
To stop playback, press the ª key on the front panel
or remote control unit.
To play a desired track
To pause playback, press the ¥?π key on the front
panel again or π key on the remote control unit.
The indication will blink, and the unit will enter play-
Press the SKIP key to select the desired track or
numerical keys.
Using headphones
Plug the headphone cord into the PHONES jack.
ume too high. Listening at high volumes for extended
periods of time may result in permanent hearing dam-
age.
Adjust the volume with the volume control.
When using headphones, take care not to turn the vol-
Track selection
Select desired tracks for playback with the skip keys on
the front panel or on the remote control.
When Auto Cue is off and the CD-01U/CD-01U Pro is
in pause mode, the beginning of selected track is locat-
ed ,and the unit enters playback standby mode.
To restart playback from the beginning of the track in
play, press the µ once.
When Auto Cue is on and the CD-01U/CD-01U Pro is
in play mode, playback begins after selecting the track.
To skip to the previous track, press µ twice.
To skip to the next track, press ≤ once.
When Auto Cue is on and the CD-01U/CD-01U Pro is
in pause or stop mode, when a track is selected, the
point where sound begins (not where the track begins)
on that track is located, and the unit enters playback
standby mode.
When Auto Cue is off and the CD-01U/CD-01U Pro is
in stop or play mode, playback begins after selecting
the track.
16
TASCAM CD-01U/CD-01UPro
6 - Playback
Selecting by track number
Frame search
Using the number keys on the remote control, the num-
ber of the desired track can be entered directly.
Even numbers with two (Audio CD) or three (MP3) digits
can be entered easily.
During playback standby, using the PITCH knob in shift
mode performs the frame accurate search.
Also, during playback standby, pressing the JOG +/-
keys on the remote control performs the frame search.
For example:
Track 9 (Audio CD): press 0 then press 9.
Track 9 (MP3): press 0, 0, and 9.
This function does not operate with MP3 discs.
Search
During playback or playback standby, pressing the
SEARCH keys continuously enables the search of a
desired portion within a track for playback.
The search function does not operate with MP3 discs.
TASCAM CD-01U/CD-01UPro
17
7 - Advanced operations
Auto Cue
When the Auto Cue function is turned on and a track is
selected, the point where sound begins (not where the
track begins) on that track is located to and the unit
enters pause mode.
Turning the Auto Cue function on and off
Press the µ key on the front panel when SHIFT indi-
cator is lit or A.CUE/DEL key on the remote control to
select the auto cue level.
When the ¥ key is pressed, playback begins at exactly
that point.
Auto cue level: OFF (default), -24, -30, -36, -42,
-48, -54, -60, -66, -72 (dB)
Auto Cue is not supported for MP3 playback.
When the Auto Cue function is activated, A.CUE indica-
tor is lit on the display.
Even when the power is turned off, the Auto Cue setting
is maintained.
During stop mode, to cue to the start of sound on track
one, just press the π key.
Auto Ready
When the Auto Ready function is on, after each track is
played, playback standby mode is entered at the begin-
ning of the next track.
When the Auto Cue function is also on, playback stand-
by mode is entered at the beginning of the sound on
the selected track, and not the beginning of that track.
The behavior of Auto Ready function is follows.
Continuous play mode:
Turning the Auto Ready function on and off
Press the ≤ key on the front panel when SHIFT indi-
cator is lit or A.RDY/INS key on the remote control to
turn the function on and off.
Pause the beginning of the next track when playback
of the current track is finished.
Single play mode:
Pause the beginning of the current track when play-
back of the current track is finished.
When the Auto Ready function is on, A.RDY indicator is
lit on the display.
Program play mode:
Even when the power is turned off, the Auto Ready set-
ting is maintained.
Pause the beginning of the next programmed track
when playback of the current track is finished.
Resume
When the resume function is on, the playback stop
position is memorized and playback starts from that
position when playback is resumed.
number 09 RESUME).
In the case of MP3 discs, the playback starts from the
beginning of the last playing track when playback is
resumed.
When the Resume function is on, RESUME indicator is
lit on the display.
Turning the Resume function on and off
Even when the power is turned off, this setting is main-
tained.
Set the resume function on and off on the menu (menu
Call
Pressing the CALL key on either the front panel or
remote control locates the unit to last play start point,
and the unit enters playback standby mode.
This function is not supported for MP3 playback.
18
TASCAM CD-01U/CD-01UPro
7 - Advanced operations
Incremental play
Turning the Incremental play function on and off
This function allows auto-cueing of the playback point
to the start of the next track when the ª key on either
the front panel or remote control is pressed, or a stop
command is received from the external device.
Set the incremental play function on and off on the
menu (menu number 11 INCR).
Pressing the ª key again or receiving the stop com-
mand again, unit enters stop mode.
When the this function is on, INCR indicator is lit on the
When this mode is enabled, pressing the ¥ key on the
remote control or receiving the play command from the
external device starts playback from the beginning of
the track following the current track.
display.
Even when the power is turned off, this setting is main-
tained.
Repeat playback
Press the REPEAT key on the remote control to turn on
the repeat mode. In this mode, all the tracks on the disc
are played continuously.
enable Program Repeat, Single-track Repeat and
Random Repeat operations, respectively.
During playback, if the repeat mode is turned on, play-
back continues as before, and when the last track fin-
ishes, playback resumes from the first track. If repeat
mode is turned on when the deck is stopped, press the
PLAY key to begin operation.
Turning the Repeat play function on and off
Turn the repeat play function on and off on the menu
(menu number 03 REPEAT). Or press the REPEAT key
on the remote control.
When the this function is on, REPEAT indicator is lit on
the display. Even when the power is turned off, this set-
ting is maintained.
Combining the repeat mode with the Program, Single-
track playback and Random playback functions will
A to B repeat playback
If a specific portion between two points on the disc is
specified, that portion can be played back repeatedly.
To cancel Repeat A-B mode and resume normal
playback
Press the REPEAT key on the remote control once more.
1 During playback and the repeat function is off, press
and hold the REPEAT key on the remote control
more than 1 second. Or set the repeat mode to A-B
on the menu (menu number 03 REPEAT).
There are three additional ways to cancel repeat A-B
mode:
Press ª key.
Search the other track.
Eject the CD.
REPEAT indicator flashes on the display.
2 Press the REPEAT key on the remote control or
PITCH knob on the front panel at the beginning of
the desired portion on the disc.
A-B indicator flashes on the display.
Both repeat start (A) and end (B) points can set to with-
in a track.
3 At the end of the desired portion on the disc, press
the REPEAT key on the remote control or PITCH
knob on the front panel again.
REPEAT and A-B indicators are lit up on the display,
and the desired A-B section will be played repeatedly.
This function is not supported for MP3 playback.
TASCAM CD-01U/CD-01UPro
19
7 - Advanced operations
Intro Check
The Intro Check function allows only the beginning of
each track to be played for 10 seconds.
This function is operational both at stop and during nor-
mal playback.
This function works in normal (continuous) play mode
and program play mode.
To exit the intro check mode, press ª key on either the
front panel or remote control, or INTRO CHECK key on
the remote control.
1 Press the STOP/INTRO CHECK key on the front
panel when SHIFT indicator is lit and playback stops.
Or, pressing the INTRO CHECK key on the remote
control to turn the intro check function on and off.
Int is shown on the display.
The intro check mode is also canceled when play mode
is changed.
2 Press the ¥?π key on the front panel or ¥key on
the remote control.
Output in monaural
Both analog and digital output can be set to mono out-
When the this function is on, MONO indicator is lit on
put mode.
the display.
Set the mono output mode on and off on the menu
(menu number 08 MONO).
Even when the power is turned off, this setting is main-
tained.
Power on play
By using an external timer, you can set the CD-
01U/CD-01U Pro to play the loaded disc automatically
when the unit is turned on by the timer.
4 Set the timer to the desired time.
Consult the timer's operation manual for details.
At the set time, the power to the CD-01U/CD-01U Pro
will be turned on, and playback will automatically begin.
1 First, plug the power cord of the CD-01U/CD-01U
Pro into the power outlet of the timer.
2 Load a CD into the unit.
3 Set the TIMER menu (menu number 07 TIMER) to on.
Pitch control
When playing back an audio CD or MP3, the pitch (or
speed) of the playback can be varied.
Pitch can be varied +/- 12.5%.
value is shown on the display and PITCH indicator
lights.
2 Rotate the PITCH knob or use the PITCH +/- keys to
set the pitch.
Use the PITCH menu (menu number 12 PITCH) to
adjust the pitch control steps from 0.1, 0.5, or 1.0%
(Default: 0.1%).
1 Press the PITCH knob on the front panel when
SHIFT indicator is unlit or press the PITCH key on
the remote control to turn the Pitch Control function
on and off.
Digital output provides the 44.1KHz digital signals con-
stantly even if pitch control is activated.
When the pitch control function is activated, pitch
20
TASCAM CD-01U/CD-01UPro
7 - Advanced operations
Changing the palyback speed without changing the key (Key Original)
When the Key Original function is ON, you can change
the playback speed without changing the key.
When the Key Original function is ON, you may find that
the audio has artifacts not present when just Pitch is
used. This is an expected result of the Key Original pro-
cessing, it does not indicate a problem with the unit.
Turn the Key Original function on and off on the menu
(menu number 01 KEY-O). Or pressing the KEY ORIG
key on the remote control turns this function on and off.
Use the PITCH knob on the front panel when SHIFT
indicator is unlit, or use the PITCH and PITCH +/- keys
to change the playback speed without affecting the key.
Program playback
This function enables playback of selected tracks in any
desired order. Up to 100 tracks can be selected from a
CD for Program playbacK.
3 Press the SEARCH ˚ key. The track number will be
entered into the program.
Or turning the PITCH knob right enters the selected
track number into the program.
1 During stop mode, press the PGM key on the remote
control.
4 Repeat the above step 2 and 3 until the desired
program is completed.
Track No.
Program No.
5 When program is completed, press the PITCH knob
on the front panel or PGM key on the remote control.
Even when the power is turned off, program is main-
tained.
Or enter the program menu (menu number 4 ProG)
then press the PITCH knob.
When the disc is ejected, the program lists are erased.
2 Use the number keys or SKIP keys on the remote
control, or SKIP keys on the front panel to select
each desired track for program playback.
Editing a programmed track
1 Enter the program mode.
3 Use the number keys or SKIP keys on the remote
control or SKIP keys on the front panel to edit the
programmed track.
2 Use the SEARCH keys to select the track for editing.
Also using the PITCH knob on the front panel to
select the track for editing.
4 When editing is completed, press the PITCH knob on
The track number will be shown in the display.
the front panel or PGM key on the remote control.
Adding a track to the program
1 Enter the program mode.
4 Use the number keys or SKIP keys on the remote
control or SKIP keys on the front panel to input the
track number of the track to be added.
2 Use the SEARCH keys on the front panel or remote
control, or using the PITCH knob on the front panel
to select the programmed track before the portion
you wish to add a track.
5 Press the PITCH knob on the front panel or PGM key
on the remote control to exit the program mode.
The track number should be shown in the display.
3 Pressing the DISPLAY key and SEARCH ˚ key
simultaneously on the front panel or pressing the
A.RDY/INS key adds the program step.
TASCAM CD-01U/CD-01UPro
21
7 - Advanced operations
Deleting a programmed track
1 Enter the program mode.
3 Pressing the DISPLAY key and SEARCH ∆ key
simultaneously on the front panel or pressing the
A.CUE/DEL key deletes the selected track.
2 Use the SEARCH keys to select the track for deletion.
Also using the PITCH knob on the front panel to
select the track for deletion. The track number will be
shown in the display.
4 Pressing the PITCH knob on the front panel or PGM
key on the remote control exits the program mode.
Fade-in and fade-out
When this function is on and CD playback begins, the
song fades in. When playback is finished, the song
fades out.
3 Set the Fade in time using with the PITCH knob on
the front panel or PREV/NEXT keys on the remote
control.
4 Press the PITCH knob on the front panel or ENTER
key on the remote control to set the fade in time and
enter the fade out time setting.
The length of the fade in/out to/from the normal level
can be set between 0.5 and 10 seconds in 0.5 second
increments (Default setting: OFF).
1 To set the fade operation, enter the fade menu (menu
number 05 FADE).
5 Set the Fade out time using with the PITCH knob on
the front panel or PREV/NEXT keys on the remote
control.
6 Press the PITCH knob on the front panel or ENTER
key on the remote control to set the fade out time
and exit the menu.
2 Press the PITCH knob on the front panel or ENTER
key on the remote control to enter the fade in time
setting.
Relay Play
When the disc in the first unit in a chain plays to the
end, the disc in the next unit in the chain will start.
4. To activate the relay play function, set the relay play
menu (menu number 06 RELAY) to on for all the units
in the chain.
Make all connections with power off.
RELAY IN
RELAY OUT
1. Check to see that all the CD-01Us are turned off.
RELAY IN
2. Refer to the diagrams, and connect the first CD-
01U's RELAY OUT to the second CD-01U's RELAY
IN, the second CD-01U's RELAY OUT to the third
CD-01U's RELAY IN, and so on. Finally, connect the
last CD-01U's RELAY OUT to the first CD-01U's
RELAY IN.
RELAY OUT
RELAY OUT
RELAY IN
3. Switch on power to all the CD-01Us.
RELAY OUT
RELAY IN
RELAY IN
22
TASCAM CD-01U/CD-01UPro
7 - Advanced operations
Time display switching
During audio CD playback (or playback standby), when
the DISPLAY key on either the front panel or the
remote control is pressed, the time display will switch
through several modes in the following order.
When playing an MP3 disc, elapsed track time is always
displayed, and the DISPLAY key does not operate.
Even when the power is turned off, the time display
mode setting is retained.
Elapsed track time (no display light indication)
Remaining track time (REMAIN is lit in the display)
Remaining disc time (T. and REMAIN are lit in the display)
When in program play mode, remaining total program
time (when T.REMAIN is lit) and total program time
(when stopped) are shown.
When stopped, the total recording time is shown, regard-
less of the status of the TOTAL and REMAIN indicators.
End of track warning (EOM)
When nearing the end of a track, a warning indication is
shown on the display.
To set the warning display time, use the EOM menu
(menu number 10 EOM).
The number of seconds before the track end that the
warning is displayed can be set beforehand, so that
when playback reaches that point, the two colons will
begin flashing on the display.
EOM time can be set from OFF, 5, 10, 15, 20, 25, 30
(default), and 35.
This function is not supported for MP3 playback.
Eject block
When eject block is on, the EJECT key cannot be used
when a disc is being played back or paused.
Use the eject block menu (menu number 02 BLOCK) to
turn this function on and off.
Fader start/Event start
Fader start/stop
Connect the RELAY IN jack (mini jack) on the rear panel
and fader start terminal on the external device which
supports the fader start function.
For CD-01U Pro only, connect the CONTROL I/O
(PRALLEL) terminal on the rear panel and fader start
terminal on the external device.
SLEEVE
STOP
CONTROL I/O
RELAY IN
STOP
PIN8 GND
START
START
PIN11
FADER STRAT/STOP
TIP
SLEEVE
TIP
The relay play menu (menu number 06 RELAY) should
be set to FDR.
See more detailes for the CONTROL I/O terminal in the
secsion External parallel control on page 24.
TASCAM CD-01U/CD-01UPro
23
7 - Advanced operations
Event start
The relay play menu (menu number 06 RELAY) should
be set to ON.
Connect the RELAY IN jack (mini jack) on the rear panel
and event start terminal on the external device which
supports the event start function.
Restoring factory default settings
To restore all settings to their factory defaults:
The following settings are restored to default values.
1 Select the factory preset menu (menu number 14 F-
PRE).
≠ Playback mode
≠ Time display mode
≠ Auto ready
2 The display shows 14 flashing, then press the PITCH
knob on the front panel or ENTER key on the remote
control to confirm the selection.
≠ Auto cue
≠ Pitch control value
≠ All menu settings
3 The display shows - SURE - flashing to recomfirm
that this operation is surely desired.
You can cancel to restore the default settings either the
stage 14 F-PRE or SURE is flashing by pressing the
other keys except the SHIFT key and the PITCH knob
on the front panel.
4 Press the PITCH knob on the front panel or ENTER
key on the remote control to restore all settings to
their default values.
External parallel control
The CD-01U Pro can be controlled from an external
devices which supports a parallel interface via the CON-
TROL I/O terminal on the rear panel.
Pin No. Description
In/Out
Out
In
1
2
3
4
5
6
7
8
9
Stop tally
Skip (Back)
Skip (Forward)
No Disc tally
EOM tally
Search (Back)
Search (Forward)
GND
In
Out
Out
In
REMOTE(PARALLEL)
In
1
8
Play tally
Out
Out
In
10 Pause tally
11 Fader start/stop
12 Stop
15
9
In
13 Play
In
14 Pause
In
15 +5V
In:
Input signals are active when low (ground) for > 30 ms.
Out:
Tally signals are open collector, with a maximum current of 50 mA.
+5V:
The maximum current supplied from this terminal is 50 mA.
24
TASCAM CD-01U/CD-01UPro
8 - Specifications
Specifications
Type
Compact Disc player
Discs
8 or 12cm (3.1 to 4.7inch) CD, CD-R/CD-RW
Formats
Audio CD (CD-DA), MP3
2-channel
Number of channels
Resolution
16-bit
Sampling frequency
Analog line outputs
Connectors
44.1kHz
RCA
Maximum Output level
Output impedance
Analog line outputs (CD-01U PRO only)
Connectors
+6 dBV dBu
1kØ
XLR-3-32 (1:GND, 2:HOT, 3:COLD)
Maximum Output level
Output impedance
Headphones
+20 dBu
150Ø
Connectors
standard stereo jack
20 mW + 20 mW
32Ø
Maximum Output level
Load impedance
Digital input (Coaxial)
Connectors
Optical
Format
IEC60958-3 (S/PDIF)
Digital output (AES/EBU, CD-01U PRO only)
Connector
XLR-3-32
Format
IEC60958-4 (AES/EBU)
Frequency response
S/N ratio
20Hz to 20kHz +0.5/- 1.0dB
> 95dB (20kHz LPF A-WTD)
> 98dB (20kHz LPF A-WTD)
< 0.01% (200Hz HPF, 20kHz LPF)
> 90 dB (at 1 kHz)
Dynamic range
Total harmonic distortion
Channel separation
Wow and flutter
Voltage requirements
Below measurable limits (less than 0.001%)
USA/CANADA
U.K./Europe
120 CVAC, 60 Hz
230 VAC,50HZ
240 VAC,50Hz
Australia
Power consumption
Dimensions
9 W (CD-01U)
11 W (CD-01U PRO)
482.6 x 50 x 333.9 mm
19 x 2 x 13.1 (in)
Weight
3.5 kg (7.7 lbs)(CD-01U)
3.7 kg (8.1 lbs)(CD-01U Pro)
5 to 40 degrees C (41∞ F to 104∞ F)
Operating temperature range
For product improvememt, specifications and external
appearance are subject to change without notice.
Due to product improvement, the actual unit may
appear differently than illustrations in the operation
manual.
TASCAM CD-01U/CD-01UPro
25
8 - Specifications
Dimensional drawing
435mm (17.1")
482.6mm (19")
Error messages
Err 01 TOC Read error - the disc's Table of Contents cannot be read - try with another disc or remove and clean the
existing disc before replacing it
Err 02 GFS error GFS signal cannot be detected - try with another disc or remove and clean the existing disc
before replacing it
Err 03 Focus error - after repeating the attempt eight times to focus, an error still occurs - try with another disc or
remove and clean the existing disc before replacing it
Err 04 Sub-Q error - the sub-Q code cannot be detected - try with another disc
Err 05 Loading error - the loading operation cannot be completed, even after retries, or there is an internal error - make sure
that there are no obstructions preventing the loading operation
Err 06 Sled error - an internal drive error - try turning the power off, waiting a few seconds, and turning it on again
Err 07 S-DRAM error - an internal S-DRAM error - try turning the power off, waiting a few seconds, and turning it on again
Err 08 System error - an internal error - try turning the power off, waiting a few seconds, and turning it on again
If any of the numbered error messages occur, try using another disc.
If the errors continue with a number of discs, turn the unit off, wait for a few seconds, and turn it on again.
If the errors still continue or other error occurs, contact your TASCAM distributor for repair.
26
TASCAM CD-01U/CD-01UPro
CD-01U/CD-01UPro
27
»
CD-01U /CD-01UPro
TEAC CORPORATION
Phone: +81-422-52-5082
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. De C.V
Phone: +52-555-581-5500
Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF
TEAC UK LIMITED
Phone: +44-1923-438880
5 Marlin House, Croxley Business Park, Watford, Hertfordshire. WD1 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
TEAC ITALIANA S.p.A.
Phone: +39-02-66010500
Via C. Cantu 11, 20092 Cinisello Balsamo, Milano, Italy
Printed in China
|