2-638-632-11(1)
This warranty is valid only in the United States.
Operating Instructions
MZ-M10
Recorder
Operation _____
page 12
Software
Operation _____
page 86
Portable
MD Recorder
“WALKMAN” is a registered trademark of Sony
Corporation to represent Headphone Stereo products.
is a trademark of Sony Corporation.
*
2
6
3
8
6
3
2
1
1
*
(1)
Printed in Malaysia
© 2005 Sony Corporation
Information
WARNING
IN NO EVENT SHALL SELLER BE
LIABLE FOR ANY DIRECT,
INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF
ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM
ANY DEFECTIVE PRODUCT OR
THE USE OF ANY PRODUCT.
To prevent fire or shock hazard, do
not expose the unit to rain or
moisture.
Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet.
For customers who purchased
this product in the USA
To prevent fire, do not cover the
ventilation of the apparatus with
newspapers, tablecloths, curtains, etc.
And don’t place lighted candles on the
apparatus.
Owner’s Record
The serial number is located at the rear of
the disc compartment lid and the model
number is located at the top and bottom.
Record the serial number in the space
provided below. Refer to them whenever
you call upon your Sony dealer regarding
this product.
To prevent fire or shock hazard, do not
place objects filled with liquids, such as
vases, on the apparatus.
Certain countries may regulate disposal of
the battery used to power this product.
Please consult with your local authority.
Model No. MZ-M10
Serial No.
Product registration
Caution
The use of optical instruments with this
product will increase eye hazard.
Please register this product on line at
www.sony.com/walkmanreg
<http://www.sony.com/walkmanreg>
Proper registration will enable us to send
you periodic mailings about software
upgrades, new products, services and
other important announcements. Thank
you.
CAUTION — INVISIBLE LASER
RADIATION WHEN OPEN
AVOID EXPOSURE TO BEAM
CAUTION — CLASS 1M INVISIBLE
LASER RADIATION WHEN OPEN
If you have any questions about
this product, contact:
DO NOT VIEW DIRECTLY WITH
OPTICAL INSTRUMENTS
— http://www.sony.com/
walkmansupport
— Sony Network Portable Audio
Support Line
1-(866)-456-7669
— Sony Customer Information
Services Center
12451 Gateway Blvd. Fort Myers,
FL 33913
2
— Consult the dealer or an experienced
radio/TV technician for help.
Declaration of Conformity
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
Trade Name: SONY
Model No.: MZ-M10
Responsible Party: Sony Electronics
Inc.
Address: 16450 W. Bernardo Dr, San
Diego, CA 92127 USA
Telephone No.: 858-942-2230
For customers in the USA and
Canada only
This device complies with Part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
RECYCLING NICKEL METAL
HYDRIDE BATTERIES
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Nickel Metal
Hydride batteries
are recyclable.
You can help
preserve our
environment by
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
returning your used
rechargeable batteries to the collection
and recycling location nearest you.
For more information regarding
recycling of rechargeable batteries, call
toll free
1-800-822-8837 or visit
http://www.rbrc.org/
Caution: Do not handle damaged or
leaking Nickel Metal Hydride batteries.
The validity of the CE marking is
restricted to only those countries where it
is legally enforced, mainly in the
countries EEA (European Economic
Area).
equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the
following measures:
— Reorient or relocate the receiving
antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
3
Disposal of Old Electrical &
Electronic Equipment
Notice for users
(Applicable in the European
Union and other European
countries with separate
collection systems)
On the supplied software
• Copyright laws prohibit reproducing the
software or the manual accompanying it
in whole or in part, or renting the
software without the permission of the
copyright holder.
This symbol on the product
or on its packaging indicates
that this product shall not be
treated as household waste.
Instead it shall be handed
over to the applicable
• In no event will SONY be liable for any
financial damage or loss of profits,
including claims made by third parties,
arising out of the use of the software
supplied with this recorder.
collection point for the
• In the event a problem occurs with this
software as a result of defective
manufacturing, SONY will replace it.
However, SONY bears no other
responsibility.
• The software provided with this
recorder cannot be used with equipment
other than that which is so designated.
• Please note that, due to continued efforts
to improve quality, the software
specifications may be changed without
notice.
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative consequences
for the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product. The recycling of materials will
help to conserve natural resources. For
more detailed information about recycling
of this product, please contact your local
city office, your household waste disposal
service or the shop where you purchased
the product.
• Operation of this recorder with software
other than that provided is not covered
by the warranty.
Applicable accessories: Remote control,
Earphones
• The ability to display specific languages
by the software will depend on the
installed OS on your PC. For better
results, please ensure that the installed
OS is compatible with the desired
language you want to display.
— We do not guarantee all the
languages will be able to be
displayed properly on the software.
— User-created characters and some
special characters may not be
displayed.
• Depending on the type of the text and
characters, the text shown by the
software may not be displayed properly
on the device. This is due to:
— The capability of the connected
device.
— The device is not functioning
normally.
4
• SonicStage and the SonicStage logo are
trademarks or registered trademarks of
Sony Corporation.
• MD Simple Burner, OpenMG, “Magic
Gate”, “MagicGate Memory Stick”,
“Memory Stick”, Hi-MD, Net MD,
ATRAC, ATRAC3, ATRAC3plus and
their logos are trademarks of Sony
Corporation.
• Microsoft, Windows, Windows NT and
Windows Media are trademarks or
registered trademarks of Microsoft
Corporation in the United States and /or
other countries.
• IBM and PC/AT are registered
trademarks of International Business
Machines Corporation.
section
• In Software Operations section, “Net
MD” refers to the recorder with
standard disc inserted and “Hi-MD”
refers to the recorder with a Hi-MD disc
or a standard disc in Hi-MD mode
inserted.
• The displayed items in the illustrations
that appear in this section may differ
from the actual items displayed by the
software.
• Explanations in this section cover
general Hi-MD/Net MD products. For
this reason, some explanations (and
some illustrations) may not be
applicable to your Hi-MD/Net MD.
Please refer to the operating instructions
of your Hi-MD/Net MD as well.
• Macintosh is a trademark of Apple
Computer, Inc. in the United States and/
or other countries.
• Pentium is a trademark or a registered
trademark of Intel Corporation.
• MPEG Layer-3 audio coding
technology and patents licensed from
Fraunhofer IIS and Thomson.
• All other trademarks and registered
trademarks are trademarks or registered
trademarks of their respective holders.
• ™ and ® marks are omitted in this
manual.
On the use of computers
Explanations in this manual assume a
familiarity with basic computer
operations. For details on the use of your
computer and the operating system,
please refer to the respective manuals.
Program © 2001, 2002, 2003, 2004, 2005
Sony Corporation
• CD and music-related data from
Gracenote, Inc., copyright © 2000-2004
Gracenote. Gracenote CDDBR Client
Software, copyright 2000-2004
Gracenote. This product and service
may practice one or more of the
following U.S. Patents: #5,987,525;
#6,061,680; #6,154,773, #6,161,132,
#6,230,192, #6,230,207, #6,240,459,
#6,330,593, and other patents issued or
pending. Services supplied and/or
device manufactured under license for
following Open Globe, Inc. United
States Patent 6,304,523.
Documentation © 2005 Sony Corporation
Gracenote is a registered trademarks of
Gracenote. The Gracenote logo and
logotype, and the “Powered by
Gracenote” logo are trademarks of
Gracenote.
5
Table of contents
Recorder Operation
Before recording .........................................................................................30
Viewing various information ......................................................................31
To start/stop recording in sync with the sound source
Viewing various information ......................................................................39
6
Adding titles (Title Input) ...........................................................................46
Dividing a track (Divide) ............................................................................53
Turning off the beep sound .........................................................................56
Viewing non-audio data stored on the disc in the display window of the
recorder (File List) .................................................................................63
7
9
About available functions and supplied
manuals
This section explains the functions of this portable MiniDisc recorder and the manuals that
have been supplied with it. Please refer to the manual that applies to each use of the
recorder.
Learning more about Hi-MD
“Hi-MD” is a new MiniDisc format with advanced capabilities over the standard MD
format.
The “What you can do with the Hi-MD Walkman” flyer
This flyer explains the major features of Hi-MD Walkman and how it
differs with standard MD Walkman.
Using the recorder
You can enjoy recording from a CD player or a microphone, then enjoy listening to the
recordings that you made.
This section explains all of the recorder functions. It also gives details
on the problems you may encounter while using the recorder and how to
solve them, and about what to do when a message appears in the display.
, When you encounter any problems or need more explanation
10
Using the recorder while it is connected to a computer (Windows)
The supplied SonicStage software allows you to transfer audio data between the recorder
and the computer.
The supplied MD Simple Burner software allows you to record audio data to the recorder.
Audio CDs
Internet
Music files
This section explains the installation and basic operations of the supplied SonicStage/MD
Simple Burner software.
SonicStage Help
This is an online help that you can view on your computer
screen.
Online help explains the detailed operations and information
about SonicStage software. You can also refer to online help
if you encounter any problems while using the SonicStage.
Using the recorder while it is connected to a computer (Macintosh)
The supplied Hi-MD WAV Importer allows you to import audio data recorded in
linearPCM on a Hi-MD Walkman to a Macintosh computer, automatically converting
linearPCM audio data to WAV-format.
LinearPCM
audio data
Hi-MD WAV
Importer
The “Hi-MD WAV Importer for Mac” operating
instructions
This operating instructions explains the installation and operations of
the supplied Hi-MD WAV Importer software.
11
Checking the supplied accessories
AC power adaptor (1)
Stereo microphone (1)
Battery carrying case (1)
Remote control (except for the
North American model) (1)
Earphones (1)
A clamp filter is attached to
the cord for the North
American model.
NH-10WM Nickel metal
hydride rechargeable
battery (1)
USB cable (1)
Clamp filters are not attached to
the cord for the Southeast Asian,
African, Mexican and tourist
models.
Dry battery case (1)
Optical cable (except for the North American and Mexican models) (1)
Clamp filters (small-size)
• for the North American model (1)
• for the European, Australian, Hong Kong and Korean models (2)
CD-ROM (SonicStage/MD Simple Burner/Hi-MD WAV Importer for Mac) (1)*
Carrying pouch (1)
* Do not play a CD-ROM on an audio CD player.
Note
When using this unit, remember to follow the precautions below in order to avoid warping the
cabinet or causing the unit to malfunction.
• Make sure not to sit down with the unit in
your back pocket.
• Make sure not to put the unit into a bag with the
remote control or the earphones cord wrapped
around it and then subject the bag to strong impact.
12
How to use the supplied clamp filters
When using the recorder connected to the computer, make sure to attach the clamp filters in
the way described. (You must attach a clamp filter to comply with the applicable EMC
standards.) It is unnecessary to attach the clamp filters if you use the unit without
connecting it to the computer.
• For the supplied remote control: small-size clamp filter/ESD-SR-110
(for the European, Australian, Hong Kong and Korean models)
• For the optional line cable (RK-G129/RK-G136): small-size clamp filter/
ESD-SR-110
(except for the Southeast Asian, African, Mexican and tourist models)
2
1
3
distance from the plug
connected to the recorder.
1 Open the clamp filter.
2 Attach the clamp filters as follows.
For the supplied remote control: Wind the cord around the clamp filter once/Approx. 4
cm (1.6 in.) from the plug
For the optional line cable: Pass the cord through the clamp filter/Approx. 1 cm (0.4
in.) from the plug
3 Close the clamp filter. Make sure the clasps are fully engaged.
13
Looking at controls
The recorder
A MIC (PLUG IN POWER) jack1)
J VOL (volume) +1), – button
K i (earphones) jack
B LINE IN (OPT) jack
C HOLD switch
L REC(+N)/T MARK button
M •SEARCH/ MENU button2)
N x (stop) • CANCEL/CHG button
O DC IN 3V jack
Slide the switch in the direction of the
arrow to disable the buttons on the
recorder. To prevent the buttons from
being accidentally operated when you
carry the recorder, use this function.
P
USB cable connecting jack
D Display window
Q The cover of the
USB cable
connecting jack
E OPEN switch
R Terminals for attaching dry battery
F Jog dial (N (play)/ENT)
case
G . (AMS, fast rewind), > (AMS,
1) There are tactile dots beside the VOL + button
and the MIC (PLUG IN POWER) jack.
2) • indicates a function that requires a slight
fast forward) button
H Battery compartment
press of the button.
indicates a function
I X (pause) button
that requires pressing the button for 2 seconds
or more.
14
The display window of the recorder
A Operating condition indication display
area
E Hi-MD/MD indication
“Hi-MD” lights up when the disc used
in Hi-MD mode is inserted in the
recorder and “MD” lights up when the
disc used in MD mode is inserted in
the recorder.
Displays the indications of each
operating condition.
x: stop
N: play
X: pause
F Battery indication
m: fast rewind
M: fast forward
., >: AMS
Shows the approximate remaining
battery power. If the batteries are
weak, the indication becomes empty
and starts flashing.
B Selected operating condition display
area
G Track number display area
Displays the recording mode, play
mode, or selected menu item, etc.
H Text information display area
Displays titles, menu items, error
messages, etc. Titles are preceded by
the following icons.
C SYNC (synchro-recording) indication
D REC indication
Lights up during recording or file
transfer from the Windows computer.
When flashing, the recorder is in
record standby mode.
: track name
: artist name*
: album name*
: group name
: disc name
* Appears only for discs used in Hi-MD mode.
I Time display area
Displays the elapsed time, remaining
time of the track or disc, etc.
15
The earphones with a remote control (except for
the North American model)
A
E
F
B
C
D
G
A VOL (volume) +, – control
C Clip
B HOLD switch
D
(group) +, – button
Slide the switch in the direction of the
arrow to disable the buttons on the
remote control. To prevent the buttons
from being accidentally operated
when you carry the recorder, use this
function.
E NX (play, pause) button
F x (stop) button
G . (AMS, fast rewind), > (AMS,
fast forward) button
16
Getting started
Charge the rechargeable battery before using.
1
Insert the rechargeable battery.
1Slide OPEN to open the
2Insert the NH-10WM
rechargeable battery E
end first.
3Close the lid.
battery compartment lid.
2
Charging the rechargeable battery.
1Connect the AC power adaptor to DC IN
3V on the recorder and the AC power
adaptor to a wall outlet.
2Press x • CANCEL/CHG.
“Charging” appears in the display, and
charging starts. When charging is
completed, “Charging” disappears.
x •
CANCEL/
CHG
To a wall
outlet
AC power
adaptor
To DC IN 3V
Make sure the
cover is closed.
continued
17
z
• If the display disappears after a short time, the
rechargeable battery is sufficiently charged.
• If the rechargeable battery is completely
drained at the start of charging, it will take
about 2.5 hours for the rechargeable battery
become sufficiently charged. The charging
time may vary, depending on the condition of
the rechargeable battery.
Using the alkaline dry battery for extended operation
2 Insert a LR6 (size AA) alkaline dry
1 Attach the dry battery case to the recorder.
battery.
Inset the battery E end first.
Rear of the
recorder
3
Make connections.
For models except USA and
Canadian models
For USA and Canadian
models
Connect the earphones with the remote
control to i.
Connect the earphones to i.
Connect firmly
Connect firmly
To i
To i
18
4
Unlock the control.
Slide HOLD to the opposite direction of the arrow (.) on the recorder or the remote
control to unlock the controls.
For models except USA and
Canadian models
For USA and Canadian
models
HOLD
HOLD
HOLD
For models supplied with the
AC plug adaptor
If the AC power adaptor does not fit the wall
outlet, use the AC plug adaptor.
When to charge the
rechargeable battery or
replace the dry battery
You can check the battery condition on the
display window of the recorder.
Notes
Battery power decreasing
• When the rechargeable battery is being
charged, the charging will stop when you
operate the recorder.
• Because of the battery’s characteristics, the
capacity of the rechargeable battery may be
smaller than normal when it is used for the
first time or after a long period of disuse. In
this case, charge and discharge the battery
several times. The normal battery life will be
restored.
• It is preferable to use the recorder on house
current when recording or editing. When
powering the recorder with batteries, make
sure to use a fully charged rechargeable
battery or a new alkaline dry battery.
• When operating the recorder with a dry
battery, make sure it is an alkaline type. Use of
another type may result in shorter battery life
or cause a deterioration in the performance of
the rechargeable battery being used in
conjunction with the dry battery.
m
Weak battery
m
The battery is drained.
“LOW BATTERY” flashes in the
display and the power goes off.
The battery level indicator is approximate. It
may be more or less than the indication
depending on the operating condition or the
operating environment.
19
Battery life
When recording continuously in Hi-MD mode
(Unit: approx.hours)(JEITA1))
Disc type
Batteries
LinearPCM
Hi-SP
Hi-LP
6.5
1GB Hi-MD disc
NH-10WM2)
LR63)
4
5.5
3
2
3.5
NH-10WM + LR6
NH-10WM
LR6
6.5
3.5
4
9
11
60/74/80-minute
standard disc
5.5
6.5
13
6.5
7.5
NH-10WM + LR6
8
15
1) Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries
Association) standard.
2) When using a 100% fully charged nickel metal hydride rechargeable battery
3) When using a Sony LR6 (size AA) alkaline dry battery (produced in Japan)
When playing continuously in Hi-MD mode
(Unit: approx.hours)(JEITA)
Disc type
Batteries
LinearPCM Hi-SP
Hi-LP
11
MP31)
1GB Hi-MD disc
NH-10WM
LR6
6.5
10.5
20
9.5
15.5
30
10
18
16.5
31.5
10
NH-10WM + LR6
NH-10WM
LR6
34.5
11
60/74/80-minute
standard disc
5.5
8.5
16.5
9
15
18
16.5
31.5
NH-10WM + LR6
28.5
34.5
1) Tracks transferred at 128 kbps
When playing continuously in MD mode
(Unit: approx.hours)(JEITA)
Disc type
Batteries
SP
10
LP2
LP4
12
60/74/80-minute
standard disc
NH-10WM
LR6
11
20
37
17.5
33
21
NH-10WM + LR6
39.5
Notes
• Stop the recorder before replacing the battery.
• When using a 1GB Hi-MD disc, the continuous recording time may be shortened if you repeatedly
make short recordings.
20
Recording a disc right away!
This section explains the basic procedure for making digital recordings using
an optical cable connected to a CD player, Digital TV or other digital
equipment. Make sure to use the optical cable.
Note
Recording cannot be done in MD mode when you record directly with this recorder without using a
Windows computer. You can record in Hi-MD mode on this recorder.
1
Make connections. (Insert the cables firmly and completely into
the appropriate jacks.)
1Connect the AC power adaptor to the
2Connect the optical cable to the
recorder and a house current.
recorder and an external component.
CD player,
MD player,
DVD video
player, etc.
To a wall
AC power
outlet
adaptor
To a digital (optical) out jack
Optical
mini-
plug
Optical
plug
To DC IN 3V
Optical cable*
Make sure the
cover is closed.
To LINE IN (OPT)
continued
21
2
Insert a recordable disc.
1Slide OPEN to open the lid.
2Insert a disc with the label side facing
front, and press the lid down to close.
Make sure to
check the
record-protect
tab is closed.
3
Confirm the operation mode.
This recorder has two operation modes, “Hi-MD mode” and “MD mode”. The operation
mode is automatically recognized whenever the disc is inserted. After you insert a disc,
check the operation mode on the display window of the recorder.
You can record on this recorder only in “Hi-MD mode”. It is not possible to record
in “MD mode”. If you want to record in “MD mode”, for example to allow the disc
to be played on another component that does not support Hi-MD, connect the
recorder to a Windows computer and use the supplied SonicStage or MD Simple
“Hi-MD” lights up when the operation mode is Hi-MD and
“MD” lights up when the operation mode is MD.
x
• When using a 1GB Hi-MD disc, the operation mode will only be Hi-MD.
• When using a standard disc (60/74/80 minutes), the operation mode can be set as follows.
Disc condition
Operation mode
Blank disc
The mode set for the “Disc Mode” in the menu.1)
, When recording on this recorder, set “Disc Mode” to “Hi-
MD” so that the operation mode will be “Hi-MD mode”.
The disc contains material Hi-MD
recorded in Hi-MD mode
The disc contains material MD
recorded in MD mode
, You cannot use this recorder to record in MD mode.
Recording in “MD mode” is possible if you use the
supplied SonicStage or MD Simple Burner software.
22
4
Record a disc.
1Select and pause the sound source to
2Make sure that the x indication
be recorded.
appears in the display window.
Make sure the x indication is displayed.
PAUSE
Connected component
3While the recorder is stopped, press
the jog dial (N/ENT) while pressing
REC(+N)/T MARK.
4Play the source you want to record.
If you insert a previously recorded disc,
the recording starts after the existing
contents.
“REC” lights up and recording starts.
Track marks are automatically added at
the same point as the sound source, and
the contents are recorded together as a
group.
REC(+N)/
T MARK
PAUSE
Jog dial
(N/ENT)
Connected component
To
Press
Stop
Pause
Press x.
Press X1).
Press X again to resume recording.
Remove the disc
Press x and open the lid. (The lid does not open while
“SYSTEM FILE WRITING” is displayed.)
1) A track mark is added at the point where you press X again to resume recording while pausing; thus
the remainder of the track will be counted as a new track.
23
z
Notes
• The recorder is factory set to make a new
group whenever recording is done. If you do
not want to make a group, set “Group REC” to
• To start recording from a specific point on the
disc, pause the recorder at the desired point,
and then start recording from that point.
• You can monitor the sound during recording.
Changing the volume level will not affect the
recording level.
• When you record on a 1GB Hi-MD disc,
connect the AC power adaptor to the recorder,
charge the rechargeable battery fully (battery
level indication shows
alkaline dry battery (battery level indication
shows ). When you attempt to start
), or use a new
recording on a 1GB Hi-MD disc, “NOT
ENOUGH POWER TO REC” may appear
and recording cannot be done even if the
battery level indication shows sufficient
remaining power while the recorder is stopped
or playing. This is because of a mechanism
that disables recording when the remaining
battery power is estimated by the recorder to
be insufficient due to the high power
consumption required for 1GB Hi-MD disc
recording.
• Make sure to place the recorder at a stable,
vibration-free place during recording.
• If you start recording before the x indication
appears in the display, the first few seconds of
the material may not be recorded. Make sure
the x indication is displayed before you start
recording.
• Do not move or jog the recorder or disconnect
the power source while recording, or while
“DATA SAVE” or “SYSTEM FILE
WRITING” is displayed. If you do, the data
recorded up to that point may not be recorded
to the disc, or data on the disc may be
damaged.
• Recording cannot be done when the disc does
not have enough space for recording.
• If the power supply is disrupted (i.e. the
battery is removed or becomes exhausted or
the AC power adaptor is disconnected) during
a recording or editing operation, or while
“DATA SAVE” or “SYSTEM FILE
WRITING” is displayed, then it will not be
possible to open the lid until power is restored.
24
Playing a disc right away!
1
Insert a recorded disc.
1Slide OPEN to open the lid.
2Insert a disc with the label side facing
front, and press the lid down to close.
2
Play a disc.
1Press the jog dial (N/ENT) on the
2Press VOL + or – to adjust the volume
on the recorder.
recorder.
Press NX on the remote control.
Turn the VOL +, – control on the remote
control.
The volume will be shown in the
display.
VOL +, –
X
x
VOL +, –
NX
x
Jog dial
(NENT)
., >
+, –
., >
To stop play, press x.
Playback starts from the point you last stopped playing. After you stop the recorder, the recorder
will automatically turn off in about 10 seconds (when using batteries) or about 3 minutes (when using
an AC power adaptor).
25
To
Operation on the recorder Operation on the remote
control
Stop
Press x.
Press x.
Pause
Press X. Press X again to
resume play.
Press NX. Press NX again to
resume play.
Select a track directly
Turn the jog dial to select a
—
viewing track number or track, and then press the jog dial
name
(N/ENT) to enter.
Find the beginning of
Press .. Press .
Press .. Press . repeatedly
until you reach the beginning of
the desired track.
the current track or the repeatedly until you reach the
previous track
beginning of the desired track.
Find the beginning of
the next track
Press >.
Press >.
Go backwards or
forward
Press and hold . or >.
Press and hold . or >.
Cue to the next or
—
Press
+ or –.
previous group while
playing a track in a
group (Group skip)1)
While the recorder is stopped,
press the jog dial (N/ENT) for 2
seconds or more.
Start with the first track
of the disc
While the recorder is stopped,
press NX for 2 seconds or more.
Remove the disc
Press x and open the lid.2)
1) Cues to the beginning of every 10th track during playback of the disc with no group settings or during
Bookmark play.
2) Once you open the lid, the point to start play will change to the beginning of the first track.
Note
The playback sound may skip if:
• the recorder is subject to strong, repeated
shocks.
• a dirty or scratched disc is played.
When using a disc in Hi-MD mode, sound may
drop out for a maximum of about 12 seconds.
26
Using menus
How to use the menu items
The recorder has many menus with useful functions for recording, playback, editing, etc.
To set the menu items, do the following procedure.
If you are doing a menu operation for the first time after purchasing the recorder, “Menu
Mode” appears in the display. Before the menu operation, you can set “Menu Mode” to
“Advanced” (all menu items appear) or “Simple” (only basic menu items appear). Refer to
“Changing the displayed menu items (Menu Mode)” (page 56) for menu mode setting.
x • CANCEL
Jog dial
MENU
Turn to select
Press to enter
Jog dial (N/ENT)
1 Press and hold MENU for 2 seconds or more to enter the menu.
2 Turn the jog dial to select the item.
3 Press the jog dial (N/ENT) to enter the selection.
The setting will be entered when you press the jog dial (N/ENT) at the last.
To return the preceding setting
Press x • CANCEL.
To cancel the operation while setting
Press x • CANCEL for 2 seconds or more.
27
List of menus
The following table shows the menu items that you can select. Menu items can be set with
the recorder only.
Items listed under “Menu 1” are the selectable items which appear when you enter the
menu, and items listed under “Menu 2” are the selectable items which appear when you
select an item in Menu 1.
It is possible to display all menu items only when “Menu Mode” is set to “Advanced”.
Menu items with an asterisk (*) are not displayed when “Menu Mode” is set to “Simple”.
Note
Different indication may be displayed depending on the operating conditions and disc settings.
The items can be displayed in other languages. For details, refer to “Selecting the display
Menu 1
Menu 2
Function
Site
page
Edit
Title Input*
Group Set*
Adding a track name, artist name,
album name, group name, or disc name.
new group.
GroupRelease*
Move*
Releases group settings.
Erase
contents.
Format*
Formats the disc and restores it to the
condition it was in at the time of
purchase (in Hi-MD mode only).
Display
Lap Time
Displays various information such as
the recorder status, etc. in the display
window.
1 Remain
Tr Property
REC Remain
All Remain
MainPlayMode
Play Mode
Selects tracks by category, such as
group name or artist name.
Sub PlayMode
Selects the type of play, such as single-
track play or shuffle play.
Repeat
Repeats playback.
Sound
Normal
Sound EQ
Plays with normal sound quality.
Customizes the sound quality.
28
Menu 1
REC Settings
Menu 2
Function
Site
page
REC Mode
SP or Hi-LP).
REC Level*
MIC AGC*
Manually adjusts the recording level.
Sets the microphone recording level
adjustment mode.
MIC Sens*
Time Mark*
Group REC*
the source sound.
Adds track marks automatically in a
specific time interval.
Selects or deselects creation of a new
group for each recording operation
(Group Recording).
SYNC REC*
—
Simplifies operations during digital
recording (Synchro-Recording).
File List
Option
Displays a list of the non-audio data
stored on a disc used in Hi-MD mode.
Menu Mode
AVLS*
Changes the displayed menu items.
protect your hearing.
Beep*
Turns the beep sound on or off.
Disc Memory*
Stores the recorder settings (Disc
Memory).
Quick Mode*
Disc Mode
Contrast*
Sets the recorder to start playback
quickly.
Selects MD mode or Hi-MD mode
when a blank disc is inserted.
Adjusts the contrast of the display
window.
Jog Dial*
display when turning the jog dial.
Language
29
Various ways of recording
Notes
Before recording
• When you record on a 1GB Hi-MD disc,
connect the AC power adaptor to the recorder,
charge the rechargeable battery fully (battery
About the operation mode
This recorder has two operation modes,
“Hi-MD mode” and “MD mode”. The
operation mode is automatically
recognized whenever the disc is inserted.
After you insert a disc, check the
operation mode on the display window of
the recorder.
You can record on this recorder only
in “Hi-MD mode”. It is not possible to
record in “MD mode”. If you want to
record in “MD mode”, for example to
allow the disc to be played on another
component that does not support Hi-
MD, connect the recorder to a
level indication shows
alkaline dry battery (battery level indication
shows ). When you attempt to start
), or use a new
recording on a 1GB Hi-MD disc, “NOT
ENOUGH POWER TO REC” may appear
and recording cannot be done even if the
battery level indication shows sufficient
remaining power while the recorder is stopped
or playing. This is because of a mechanism
that disables recording when the remaining
battery power is estimated by the recorder to
be insufficient due to the high power
consumption required for 1GB Hi-MD disc
recording.
• Make sure to disconnect the supplied USB
cable before recording. Recording may not
occur if the USB cable is connected to the
recorder.
• If you start recording before the x indication
appears in the display, the first few seconds of
the material may not be recorded. Make sure
the x indication is displayed before you start
recording.
Windows computer and use the
supplied SonicStage or MD Simple
Burner software to record in MD
mode (refer to the “Software
Operation” section).
“Hi-MD” lights up when the operation
mode is Hi-MD and “MD” lights up
when the operation mode is MD.
• Do not move or jog the recorder or disconnect
the power source while recording, or while
“DATA SAVE” or “SYSTEM FILE
WRITING” is displayed. If you do, the data
recorded up to that point may not be recorded
to the disc, or data on the disc may be
damaged.
x
For details on the operation mode for
different disc conditions, refer to
Selecting the Menu Mode
If the “Simple” menu mode is selected,
some menu items will not be displayed. If
you cannot find certain menu items while
operating the recorder, make sure that the
menu mode is set to “Advanced”.
For details on selecting the menu mode,
30
While the recorder is stopped
Lap Time
Viewing various
information
A
B
C
Track number
Elapsed time
Track name
You can check the remaining time, track
number, etc. when recording or during
stop.
Artist name (Hi-MD)/
MENU
Group name (MD)
Album name (Hi-MD)/
Disc name (MD)
1 Remain
Jog dial
A
B
Track number
Remaining time after the current
location in the track
1 Enter the menu and select “Display”.
2 Turn the jog dial to select the
information you want, and then press
the jog dial to enter the selection.
C
Track name
Artist name (Hi-MD)/
Group name (MD)
Album name (Hi-MD)/
Disc name (MD)
Each turn selects the menu item as
follows:
While the recorder is stopped:
“Lap Time” t “1 Remain” t “Tr
Property” t “REC Remain” t “All
Remain”
While recording:
“Lap Time”
Tr Property
A
B
C
Track number
Elapsed time
Track name
When you press the jog dial, the
selected information appears at A,
B and C.
Group name
Codec information (Hi-MD)1)/
Track mode information (MD) and
time and date of recording2)
1) If the case of an MP3 track that supports VBR
(Variable Bit Rate), the bit rate that appears
here may not match the one displayed by the
SonicStage software.
2) Appears for tracks that have time stamp
information.
REC Remain
A
B
C
Track number
Elapsed time
Disc name
Remaining recording time and
remaining free space (in Hi-MD
mode only)
continued
31
All Remain
Recording from a
microphone
A
B
C
Track number
Elapsed time
Disc name1)
Stereo
microphone
(supplied)
Remaining time after the current
location on the disc and number of
tracks after the current track
1) The title that is displayed varies according to
the selected Main play mode.
To MIC (PLUG IN
POWER)
While recording
Lap Time
REC(+N)/
T MARK
A
B
Track number
MENU
Elapsed time
Time mark indication1)
C
Remaining recording time
Recording level meter (L • R)
Jog dial
(N/ENT)
1) Appears when “Time Mark” is set to “On”.
1 Connect the stereo microphone to the
Notes
MIC (PLUG IN POWER) jack.
• When a disc used in Hi-MD mode is inserted
in the recorder, the free space will show as
“2.0MB” when the remaining recording time
becomes “–00:00”. This is a system
limitation, “2.0MB” being the capacity of the
reserve domain.
• Depending on the group settings, the
operating conditions, and the disc settings,
you may not be able to select certain
indications or the indications may appear
differently.
2 Press the jog dial (N/ENT) while
pressing REC(+N)/T MARK to
start recording.
To select microphone
sensitivity
You can select the microphone sensitivity
depending on the volume of the sound
source.
z
If you want to check the playing position or
track name while playing, see “Viewing various
1 While the recorder is recording or
stopped, enter the menu and select
“REC Settings” - “MIC Sens”.
32
2 Turn the jog dial to select “Sens
High” or “Sens Low”, and then press
the jog dial to enter the selection.
Notes
• The recorder automatically switches input in
the following order; optical input, microphone
input, and analog input. You cannot record
through the microphone while an optical cable
is connected to the LINE IN (OPT) jack.
• You cannot set the “MIC AGC” setting if you
are recording with the recording level
Sens High: When recording a soft
sound or a sound with a normal
volume.
Sens Low: When recording with a
loud or close-range sounds, such as
those during an oral recording or a
music concert.
• The microphone may pick up the operating
sound of the recorder itself. Use the
microphone away from the recorder in such
cases.
• If you record with the microphone
To change the microphone
recording level adjustment
mode
disconnected from its cord and directly
connected to the recorder, the sound of the
recorder operations may be picked up.
• Only the left-channel sound is recorded when
a monaural microphone is used.
• When recording a normal volume sound (soft
music, etc.), set “MIC AGC” to “Standard”. If
an unexpectedly loud sound is input when
“MIC AGC” is set to “ForLoudMusic”, the
recorded volume thereafter may drop very
low, depending on the sound source.
When recording with a microphone, you
can select automatic adjustment mode
which sets the microphone recording level
to suit the sound source.
1 While the recorder is recording or
stopped, enter the menu and select
“REC Settings” - “MIC AGC”.
2 Turn the jog dial to select “Standard”
or “ForLoudMusic”, and then press
the jog dial to enter the selection.
Standard: When recording a sound
source with a normal volume, such as
a conversation or soft music.
ForLoudMusic: When recording a
sound source with a comparatively
high volume, such as a music concert
or a practice session with a musical
instrument.
z
• When “MIC AGC” is set to “ForLoudMusic”,
sound can be recorded with less distortion
during high volume input, and with natural
volume transitions similar to those of the
original.
• When using a plug-in power-type
microphone, the microphone can be operated
even when its power switch is turned off since
power is supplied from the recorder itself.
33
Recording from a TV or
radio (Analog
Selecting the recording
mode
Recording)
Select each recording mode according to
the recording time that you want.
This section explains how to record from
equipment with analog output, such as a
cassette recorder, radio, or TV.
You can record only in Hi-MD mode
on this recorder. If you want to record
in MD mode, connect the recorder to
a Windows computer and record or
transfer audio data using the
supplied SonicStage or MD Simple
Burner software (refer to the
“Software Operation” section).
TV, cassette
recorder, etc.
MENU
To LINE OUT jacks, etc.
L
R
(red)
(white)
Jog dial
Line cable
RK-G129,
RK-G136, etc.
1 While the recorder is stopped, enter
the menu and select “REC Settings” -
“REC Mode”.
To LINE IN (OPT)
2 Turn the jog dial to select the desired
recording mode, and then press the
jog dial to enter the selection.
REC(+N)/
T MARK
The recording mode is saved on the
recorder until it is next changed.
Jog dial
(N/ENT)
Recording Display Recording time
mode
LinearPCM PCM
• Approx. 28 min.
on an 80-minute
standard disc
1 Make connections.
• Approx. 1 hour
and 34 min. on a
1GB Hi-MD disc
Use the appropriate connecting cord
to suit the source equipment. For
details, see “Optional accessories”
Hi-SP
Hi-SP
• Approx. 2 hours
and 20 min. on an
80-minute
2 Press the jog dial (N/ENT) while
pressing REC(+N)/T MARK to
start recording.
standard disc
• Approx. 7 hours
and 55 min. on a
1GB Hi-MD disc
3 Play the source you want to record.
34
3 Play the source.
Recording Display Recording time
mode
4 While observing the level meter in the
display, adjust the recording level by
turning the jog dial.
Hi-LP
Hi-LP
• Approx. 10 hours
and 10 min. on an
80-minute
Set the level so that the meter
segments light up around –12dB
segment. If high sound input causes
the segments beyond the “OVER”
segment to light up, lower the
recording level.
Each level meter shows the following.
Upper — L channel input level
Lower — R channel input level
standard disc
• Approx. 34 hours
on a 1GB Hi-MD
disc
z
Audio components that support the linearPCM,
Hi-SP and Hi-LP mode are indicated by the
or
logo mark.
Volume increases (,)
Notes
or decreases (<)
• It is recommended that you use the AC power
adaptor for long recordings.
• It is recommended that you use the recorder to
edit (dividing or combining) long tracks
recorded in linearPCM. Transferring such
tracks and editing them on a Windows
computer may require an extremely long time.
–12dB
OVER
Adjusting the recording
level manually
5 Press X again to start recording.
If your source is an externally
connected component, play the
source to the beginning of the
material to be recorded, and then start
recording.
The recording level is adjusted
automatically while recording. If
necessary, you can set the recording level
manually during both analog and digital
recording.
To switch back to automatic
level control
Select “Auto (AGC)” in step 2.
REC(+N)/
T MARK
X
Notes
• You cannot adjust the left and right channel
levels separately.
MENU
• Once you stop recording, the recorder will
revert to automatic recording level adjustment
mode the next time you start a recording
operation.
• To adjust the recording level manually when
procedure in this section with “SYNC REC”
is set to “Off”. Afterwards, set “SYNC REC”
Jog dial
1 Press REC(+N)/T MARK while
pressing X.
The recorder stands by for recording.
2 Enter the menu and select “REC
Settings” - “REC Level” - “Manual”.
35
To cancel Time Mark
Select “Off” in step 1.
Adding track marks
while recording
Using Time Mark to add track
marks while recording
You can add track marks (track number)
while recording to divide the material into
separate parts, that allow you to go to
specific track quickly and easily.
When the elapsed recording time
exceeds the time interval for Time
Mark:
The recorder adds track marks at the point
you set the time interval and from that
point the recorder adds a track mark
whenever the time interval has elapsed.
REC(+N)/
T MARK
Example: Eight minutes of recording
has been completed when the Time Mark
time interval is set to 5 minutes.
A track mark will be added at the 8-
minute point (after the start of recording)
and after each 5-minute interval
thereafter.
Jog dial
MENU
Adding track marks manually
While the recorder is recording, press
REC(+N)/T MARK at the point you
want to add a track mark.
When the time interval set for Time
Mark exceeds the elapsed recording
time:
The recorder adds track marks when the
set Time Mark time interval has elapsed.
Adding track marks
automatically
Example: Three minutes of recording
has been completed when the Time Mark
time interval is set to 5 minutes.
A track mark will be added at the 5-
minute point (after the start of recording)
and after each 5-minute interval
thereafter.
Use this feature to add track marks
automatically at specified intervals when
recording through the analog input
connector or a microphone. This function
is convenient for recording long period of
time, such as lectures, meetings, etc.
1 While the recorder is recording or in
recording pause, enter the menu and
select “REC Settings” - “Time Mark”
- “On”.
z
“T MARK” appears before the time display for
track marks added automatically.
Notes
2 Turn the jog dial to select the desired
time interval, and then press the jog
dial to enter the selection.
• If you add a track mark by pressing
REC(+N)/T MARK or X, etc. while
recording, the recorder will start adding track
mark automatically each time the selected
time interval as elapsed.
One rotation changes the time setting
(Time __ min) by 1 minute, within the
range of 1 to 60 minutes.
• The setting is canceled when you connect a
digital optical cable to the recorder.
36
Disc with no groups recorded
Recording without
creating a new group
Disc
The recorder is factory set to
automatically create a new group for each
recording. To record without creating a
new group, set the recorder as follows.
1 2 3 4 5 6 7 8 12 13 1415
You can record a maximum of 255 groups
on a disc.
MENU
If you record a track without creating a
group, but then later want to create a
Jog dial
While the recorder is stopped, enter the
menu and select “REC Settings” - “Group
REC” - “Off”.
What is the group function?
The group function allows you to place
several tracks into one unit.
For example, if you create a group for all
your favorite tracks, then you can select
that group to play those tracks.
The following figure shows the difference
between a disc on which groups are
recorded and a disc on which no groups
are recorded.
Disc with groups recorded
Disc
Group 1
Group 2
Group 3
1 2345 6 7 1 2345 1 23
Tracks that were not assigned to a group are
treated as being part of “Group - -”.
37
Notes
To start/stop recording
in sync with the sound
source
• The pause function cannot be turned on or off
manually during synchro-recording.
• Do not switch the “SYNC REC” setting while
recording. Recording may not be done
properly.
(Synchro-recording)
When making a digital recording (e.g.,
from a CD), this function automatically
starts and stops the recorder in
synchronization with the sound source.
This eliminates the need for separate
operation of the recorder and the sound
source.
• Even when there is no sound on the sound
source, there may be cases when recording
does not pause automatically during synchro-
recording due to the noise level emitted from
the sound source.
• If a silent portion is encountered for
approximately 2 seconds during synchro-
recording from a sound source other than a
CD or an MD, a new track mark is
automatically added at the point where the
silent portion ends.
MENU
Jog dial
While the recorder is stopped, enter the
menu and select “REC Settings” - “SYNC
REC” - “On”.
z
When there is no sound from the player for
about 3 seconds during synchro-recording, the
recorder goes into the standby mode
automatically. When the sound comes from the
player again, the recorder resumes synchro-
recording. If the recorder is kept in the standby
mode for 5 minutes or longer, the recorder stops
automatically.
38
Various ways of playback
1 Remain
Viewing various
information
A
B
C
Track number
Remaining time of the current track
You can check the track name, disc name,
etc. during playback.
Track name
Artist name (Hi-MD)/
Group name (MD)
Album name (Hi-MD)/
Disc name (MD)
MENU
Tr Property
Jog dial
A
B
C
Track number
Elapsed time
Track name
1 Enter the menu and select “Display”.
2 Turn the jog dial to select the
information you want, and then press
the jog dial to enter the selection.
Group name
Codec information (Hi-MD)1)/
Track mode information (MD) and
time and date of recording2)
Each turn selects the display as
follows.
“Lap Time” t “1 Remain” t “Tr
1) If the case of an MP3 track that supports VBR
(Variable Bit Rate), the bit rate that appears
here may not match the one displayed by the
SonicStage software.
Property”
When you press the jog dial, the
selected information appears at A,
B and C.
2) Appears for tracks that have time stamp
information.
Note
Depending on the group settings, the operating
conditions, and the disc settings, you may not
be able to select certain indications or the
indications may appear differently.
z
If you want to check the remaining time or the
recording position while recording or in stop
mode, see “Viewing various information”
While the recorder is stopped
Lap Time
A
B
C
Track number
Elapsed time
Track name
Artist name (Hi-MD)/
Group name (MD)
Album name (Hi-MD)/
Disc name (MD)
39
Playing tracks in normal mode
(Normal Play)
Selecting the play
mode
You can listen to tracks in various play
modes. The play mode can consist of a
combination of Main play mode, Sub play
mode and Repeat play.
• Main play mode: selects the playback
unit, such as tracks or groups
2 When selecting a track out of a group,
skip this step.
When selecting a track within a
group, turn the jog dial to select the
group that the desired track belongs,
and then press the jog dial to enter.
• Sub play mode: selects the type of play
• Repeat play: selects Repeat play
MENU
A list of the tracks in the selected
group appears in the display.
3 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
Jog dial
The selected track starts playing. The
recorder plays from the selected track
to the last track in the disc.
Playing tracks in Main play
mode
Listening to tracks in a
specific group (Group Play)
Selects the first track to be played in Main
play mode.
1 While playing, enter the menu and
select “Play Mode” -
“MainPlayMode”.
A list of the groups on a disc appears.
The Main play mode display appears.
2 Turn the jog dial to select the desired
group, and then press the jog dial to
enter.
2 Turn the jog dial to select the desired
play mode, and then press the jog dial
to enter the selection.
A list of the tracks in the selected
group appears.
Display
Play mode
Normal Play
All tracks after the
selected track are played.
3 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
Group Play
Artist Play1)
Tracks in a specified
group are played.
The selected track starts playing. The
recorder plays the tracks in that
group, from the selected track to the
last track.
Tracks by a specified artist
are played.
album are played.
z
BookmarkPlay Bookmarked tracks are
played.
Tracks that do not belong to a group are placed
together in “Group - -” and displayed at the last
of the list of groups.
1) Appears only for discs used in Hi-MD mode.
40
Listening to tracks by a
specific artist (Artist Play) (in
Hi-MD mode only)
2 Turn the jog dial to select the desired
album name, and then press the jog
dial to enter.
If the track data includes the artist name,
you can listen to tracks by a specific artist
only.
A list of the tracks in the selected
album appears in recorded order.
3 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
The selected track starts playing. The
recorder plays the tracks in that
album, from the selected track to the
last track.
A list of the artists on the disc appears
in alphabetical order.
2 Turn the jog dial to select the desired
artist name, and then press the jog
dial to enter.
z
Tracks without album name data are placed
together in “
at the last of the list of albums.
__ (space)” and are displayed
A list of the tracks of the selected
artist appears in recorded order.
Listening to selected tracks
only (Bookmark Play)
You can bookmark tracks on a disc and
play them only. The sequence of
3 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
The selected track starts playing. The
recorder plays the tracks by the same
artist on the disc, from the selected
track to the last track.
bookmarked tracks cannot be changed.
To bookmark the tracks
1 While playing the track you want to
bookmark, press the jog dial for 2
seconds or more.
z
Tracks without artist name data are placed
together in “
__ (space)” and are displayed
at the last of the list of artists.
Listening to tracks of a
selected album (Album Play)
(in Hi-MD mode only)
If the track data includes the album name,
you can listen to tracks of a selected
album only.
tracks.
To play the bookmarked tracks
A list of the albums on the disc
appears in alphabetical order.
continued
41
2 Turn the jog dial to select a track, and
then press the jog dial to enter the
selection.
Listening to a section of a
track repeatedly (A-B Repeat)
Make sure that points A and B are within
the same track.
To erase bookmarks
While playing the track for which you
want to erase the bookmark, press the jog
dial for 2 seconds or more.
1 While playing a track that contains
the section you want to repeat, do step
Playing tracks in Sub play
mode
“Ap” flashes in the display.
2 Press the jog dial at the starting point
By specifying Sub play modes, you can
listen to tracks selected in Main play
mode in various ways.
For example, by selecting “Group Play”
in Main play mode and “Shuffle” in Sub
play mode, the recorder will play the
tracks in the selected group in random
order.
(A).
Point A is entered and “B” flashes in
the display.
3 Press the jog dial at the ending point
(B).
Point B is entered, “ApB” and “
lights up, and the section between
point A and B starts playing
repeatedly.
”
1 Enter the menu and select “Play
Mode” - “Sub PlayMode”.
2 Turn the jog dial to select the desired
play mode, and then press the jog dial
to enter the selection.
z
You can reset points A and B by pressing the
> button during A-B Repeat play.
Note
Display
Play mode
If the recorder comes to the end of the last track
on the disc while you are selecting point A, the
setting is canceled.
Normal
Normal play (All tracks
are played once.)
1 Track
Shuffle
Single-track play (A
single track is played.)
Playing tracks repeatedly
(Repeat Play)
Shuffle play (All tracks in
the selected Main Play
Mode are played in
random order.)
You can use the Repeat play function to
repeat tracks in all play modes except
when selecting A-B Repeat play.
A-B Repeat1)
A-B Repeat play (Tracks
between the selected
points A and B are played
repeatedly.)
1 While playing, enter the menu and
select “Play Mode” - “Repeat”.
1) “A-B Repeat ” does not appear when the
2 Turn the jog dial to select “On”, and
then press the jog dial to enter the
selection.
appears in the display.
42
To cancel Repeat Play
Searching for a track by initial
character (Initial Search)
You can search for a track, group, artist,
or album by its initial character.
Searching for a track
(Search)
2 Turn the jog dial to select “Initial”,
You can easily search for a track by track
name, group name, artist name, or album
name.
and then press the jog dial to enter.
SEARCH
Jog dial
3 Turn the jog dial to select the first
character of the name to be searched
for, and then press the jog dial to enter
the letter.
1 Press SEARCH.
2 Turn the jog dial to select the item
you want to use for searching, and
then press the jog dial to enter.
The following characters can be
entered for an initial search.
Display
To
Display
To
Alphabet
(A to Z)
Searches for a name
starting with an English
letter.
by Track
search by track name
search by group name
search by artist name
search by album name
by Group
by Artist1)
by Album1)
Num (Numbers) Searches for a name
starting with a number.
Other
Searches for a name
starting with a character
other than an English
letter or a number.
1) Appears only for discs used in Hi-MD mode.
skip this step.
When you press the jog dial, a list of
tracks, groups, artists, or albums with
names starting with the selected
initial character appears in the
display.
If you select an item other than “by
select the desired group, artist, or
album, and then press the jog dial to
enter.
A list of tracks for the selected group,
artist, or album appears in the display.
4 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
4 Turn the jog dial to select the desired
track, and then press the jog dial to
enter the selection.
The selected track starts playing.
43
Notes
Selecting the sound
quality (6-Band
Equalizer)
• During a search, unlabeled tracks appear at
the end of each list.
Jog dial
• During a search, ungrouped tracks are placed
together as “Group - -” and appear at the end
of the list of groups.
MENU
• During a search, tracks without artist name
data are placed together as “
__ (space)”,
and tracks without album name data are
placed together as “ __ (space)” and
appear at the end of the list.
., >
• While the recorder is sorting the selected
items, “SORTING” appears in the display.
• The Search function is automatically canceled
if no operation is made for 3 minutes.
1 While playing, enter the menu and
select “Sound” - “Sound EQ”.
2 Turn the jog dial to select the desired
sound mode, and then press the jog
dial to enter the selection.
When you press the jog dial, the
selected sound mode will appear at
A.
The icon “
” indicates that a sound
mode has been set.
Sound mode
A
Heavy
H
P
J
Pops
Jazz
Unique
Custom 11)
Custom 21)
U
1
2
1) “Custom 1” and “Custom 2” do not appear on
European models.
“Custom 1” and “Custom 2” do not appear
when the “Menu Mode” is set to “Simple”
44
To cancel the setting
Note
6-Band Equalizer will not function during
recording.
To modify and store the sound
(For models except European
models)
You can modify the sound and store the
results in “Custom 1” and “Custom 2”.
2 Press . or > repeatedly to
select the frequency.
Frequency (100 Hz)
From the left, you can select 100 Hz,
250 Hz, 630 Hz, 1.6kHz, 4 kHz, or 10 kHz
3 Turn the jog dial to adjust the level.
Level (+10 dB)
You can select from among seven levels.
–10 dB, –6 dB, –3 dB, 0 dB, +3 dB, +6 dB,
+10 dB
level for each frequency.
5 Press the jog dial to enter the
selection.
45
Editing recorded tracks
Before editing
Adding titles (Title
Input)
Notes
You can add titles to tracks, groups and
discs. You can also add artist names and
album names to tracks on a disc used in
Hi-MD mode.
• When you edit the contents of a 1GB Hi-MD
disc, connect the AC power adaptor to the
recorder, charge the rechargeable battery fully
(battery level indication shows
), or use a
new alkaline dry battery (battery level
indication shows
). When you attempt to
Available characters
edit on a 1GB Hi-MD disc, “NOT ENOUGH
POWER TO EDIT” may appear and editing
cannot be done even if the battery level
indication shows sufficient remaining power
while the recorder is stopped or playing. This
is because of a mechanism that disables
editing when the remaining battery power is
estimated by the recorder to be insufficient
due to the high power consumption required
for 1GB Hi-MD disc editing.
• Capital and small letters of the alphabet
for English and European languages1)
• Numbers 0 to 9
1) European alphabets appear only for discs used
in Hi-MD mode.
2) The available symbols will differ for Hi-MD
mode and MD mode (see “About the character
• Close the record-protect tab on the side of the
disc before editing.
Maximum number of
characters per name
Track names, group names, and disc
name: Approx. 200 each (containing a
mixture of all available characters)
• Do not move or jog the recorder or disconnect
the power source while editing or “SYSTEM
FILE WRITING” is displayed. If you do, the
data edited up to that point may not be
recorded to the disc, or data on the disc may
be damaged. “SYSTEM FILE WRITING” is
displayed while the editing results are being
recorded.
Maximum number of
characters that can be input
per disc*
• While “SYSTEM FILE WRITING” is
displayed, the lid becomes locked.
In Hi-MD mode:
A maximum of about 55,000 characters
In MD mode:
A maximum of about 1,700 characters
* The number of titles that can be stored on a
disc depends on the number of characters that
are input for track names, group names, artist
names, album names and disc name.
46
About the character palette
VOL +, –
X
During operations on the recorder,
characters can be selected from the
character palette in the display window.
The character palette has the following
configuration.
Jog dial
(N/ENT)
MENU
x
Characterpalette
for Hi-MD mode
Characterpalette
for MD mode
., >
Labeling
You can do a labeling operation while the
recorder is stopped or playing. You can
also label artist names and album names
to tracks in a disc used in Hi-MD mode.
To label a track with a track name, artist
name, or album name, you must first
select the track that you want to label. To
add a group name, you must first select a
track that belongs to the group you want
to label.
1 Enter the menu and select “Edit” -
“Title Input”.
Since only a part of the character palette
is visible on the display, use the controls
or buttons to move the cursor and enter
characters.
2 Turn the jog dial to select one of the
following, and then press the jog dial.
Title
Display
Track
Track name
Letter input area
Group name
Group
Artist1)
Album1)
Disc
The cursor appears.
Artist name (to a track)
Album name (to a track)
Disc name
1) Appears only for discs used in Hi-MD mode.
The cursor flashes in the letter input
area.
The cursor flashes.
Character palette
Note
If you enter the symbol “//” between the
characters in disc names such as “abc//def”, you
may be unable to use the group function (in MD
mode only).
continued
47
3 Turn the jog dial downward.
Functions1)
Operations
The cursor shifts from the letter input
area to the character palette.
To switch between
capital letters and
small letters.
Press X.
The cursor and character alternate.
1) Functions of the buttons or the control may
differ depending on when the cursor is in the
letter input area or in the character palette.
characters of the label name.
6 Press the jog dial for 2 seconds or
more to enter the title.
4 Select a letter and press the jog dial to
Re-labeling
enter.
You can change the titles by doing the
The selected letter appears in the
letter input area and the cursor moves
to the next input position.
Notes
The cursor flashes at the next input
position.
• The recorder is able to display, but cannot
label using Japanese “Katakana” characters.
• The recorder cannot rewrite a disc or track
name of more than 200 letters that was created
by another device (in MD mode only).
The buttons used for character input
and their functions are listed below.
Functions1)
Operations
To move the cursor Press . or >.
to the left or to the
right.
To move the cursor Turn the jog dial.
up or down
To enter a letter.
Press the jog dial
(N/ENT).
To insert a blank
space.
Press VOL +.
To delete a letter.
Press VOL –.
To move the cursor Press x.
from the character
palette to the letter
input area.
48
Notes
Assigning tracks or
groups as a new group
(Group Set)
• When the total number of characters in the
titles on a disc exceed the maximum that can
be input:
—If the disc is being used in Hi-MD mode,
you can make a group setting, but cannot
With this function, you can assign
existing tracks or groups to a new group,
and also you can assign a track that
currently belongs to no group to an
existing group.
You can create a maximum of 255 groups
on a disc used in Hi-MD mode and 99
groups on a disc used in MD mode.
—If the disc is being used in MD mode, you
cannot make a group setting.
• The tracks or groups must be sequential. If the
desired tracks or groups are not consecutive,
you must move them to make them
consecutive before you can assign them
Disc
MENU
Track number
Group 2
Group 1
1 2 3 4 5 6 7 8 9 101112
Jog dial
Assigning tracks 1 to 3 to a new
group
Assigning group 1 and group 2 to a
new group
1 While the recorder is stopped, enter
the menu and select “Edit” - “Group
Set”.
2 Turn the jog dial to select the number
of the desired first track, and then
press the jog dial to enter.
Disc
Group 2
Group 1
This selects the first track of a new
group. If the disc contains groups,
only the first track number of each
group is displayed.
1 2 3 4 5 6 7 8 9 101112
Registration of non-consecutive tracks is
not possible (for example, track 3 and
tracks 7 and 8 cannot be assigned to a new
group).
It is not possible to make a new group if
the first track or last track of the group has
been selected from the middle of an
existing group.
Track numbers appear according to their
order on the disc, not their order within
the group.
continued
49
3 Turn the jog dial to select the number
of the desired last track, and then
press the jog dial to enter.
4 Turn the jog dial to select “OK”, and
then press the jog dial to release a
group.
This selects the last track of the new
group and the group can be labeled. If
the disc contains groups, only the last
track number of each group is
displayed.
The group setting of the selected
group is released.
Moving recorded tracks
or groups (Move)
You can change the order of the recorded
tracks or groups.
Notes
track of an existing group or a track that does
not belong to a group.
MENU
sure the track comes after the one selected in
track of an existing group or a track that does
not belong to a group.
Jog dial
Moving a track on a disc
Releasing a group
setting (Group Release)
You can move a track from one group to
another or from inside a group to outside
the group. When you move tracks, track
numbers are automatically renumbered.
Select a group you want to release and
check the contents (see “Listening to
1 While playing the track you want to
move, enter the menu and select
“Edit” - “Move” - “Track Move”.
x
MENU
If the selected track is in the group,
the name of the group to which the
currently selected track belongs
appears with “B” in the display.
Jog dial
When the currently selected track is
in a group
1 Select a group that you want to
release and check the contents (see
2 Press x.
3 Enter the menu and select “Edit” -
“GroupRelease”.
50
If the selected track is not in the
group, the name of the currently
selected track appears with “B” in the
display.
Changing the order of a
group on a disc
1 While playing a track within a group
whose order you want to change,
enter the menu and select “Edit” -
“Move” - “Group Move”.
When the currently selected track is
in a group
The name of the group to which the
currently selected track belongs
appears with “B” in the display.
2 If you are moving a track from inside
a group to outside the group, or if
there is no group on a disc, skip this
step.
Name of
the group
you want
to move
If you are moving a track to a
different group, turn the jog dial to
select the destination group, and then
press the jog dial to enter.
2 Turn the jog dial to select the
destination position, and then press
the jog dial to enter the selection.
Example: When moving the group “My Best” to
the position after the group “Single Collection”
Name of the
destination
group
Destination
position in
the disc
If you are moving a track within the
same group, select the group to which
the currently selected track belongs.
Note
3 Turn the jog dial to select the
destination position, and then press
the jog dial to enter the selection.
If all tracks are moved out of the group, the
group automatically disappears from the disc.
The track moves to the selected
destination.
Name of the
destination
group
Destination
position
51
To erase a track
Erasing tracks and the
entire disc (Erase)
Note that once a recorded item has
been erased, it cannot be recovered.
Make sure to confirm the contents of
the selected item before erasing it.
1 While playing the track you want to
erase, enter the menu and select
“Edit” - “Erase” - “Track Erase”.
2 Turn the jog dial to select “OK”, and
then press the jog dial to erase the
track.
When erasing tracks that have
been transferred from the
Windows computer
When you try to erase tracks that have
been transferred from the Windows
computer, “TRK FROM PC ERASE
OK?” appears in the display. If you erased
tracks that have been transferred from the
computer, the transfer authorization of the
tracks will be as follows.
The track is erased and the next track
starts to play. All the tracks after the
one erased are automatically
renumbered.
Note
If all tracks in a group are erased, the group is
automatically deleted from the disc.
• If the tracks were transferred in Hi-MD
mode, the transfer authorization of the
tracks are restored automatically when
you insert the disc into the recorder and
then connect the recorder to the
computer.
• If the tracks were transferred in MD
mode, the transfer authorization of the
tracks is lost. If you do not want to lose
the transfer authorization, restore the
authorization by transferring the tracks
to the computer again before erasing
them.
To erase a part of a track
Add track marks at the beginning and the
end of the part you want to erase, then
To erase a group
1 Select a group you want to erase and
2 Press x.
3 Enter the menu to select “Edit” -
“Erase” - “Group Erase”.
Note
4 Turn the jog dial to select “OK”, and
then press the jog dial to erase the
group.
You cannot erase non-audio data (for example,
text data or image data) on a disc used in Hi-
MD mode.
The group is erased.
x
MENU
Jog dial
52
To erase the whole disc
Dividing a track (Divide)
You can divide a track with a track mark,
creating a new track from the part
following the track mark. The track
numbers will increase as follows.
1 Play the disc you want to erase to
check the contents.
2 Press x.
3 Enter the menu to select “Edit” -
1
2
3
4
“Erase” - “All Tr Erase”.
“ALL TRACKS WILL BE
ERASED” appears in the display.
Track marking
1
2
3
4
5
4 Turn the jog dial to select “OK”, and
then press the jog dial to erase the
whole disc.
Track numbers increase.
“SYSTEM FILE WRITING” appears
in the display, and all the tracks will
be erased.
When erasing completes, “NO
TRACK” appears in the display in
Hi-MD mode and “BLANKDISC”
appears in MD mode.
Note
You cannot divide a track if:
• the track has been transferred from a Windows
computer.
• the track has been recorded in Hi-MD mode
using the MD Simple Burner software.
• the dividing point is at the beginning or end of
the track.
• the division would cause the total number of
tracks on the disc to exceed the maximum
allowed (2,047 tracks for a disc used in Hi-
MD mode or 254 tracks for a disc used in MD
mode).
T MARK
Dividing a track directly
While playing or pausing, press T MARK
at the point you want to mark.
53
To add track marks while
recording (except while
synchro-recording)
1 While playing the track with the track
mark you want to erase, press X to
pause.
Press T MARK on the recorder at the
point you want to add a track mark.
You can use the “Time Mark” setting to
add track marks automatically at specified
intervals (except while digital recording)
2 Find the track mark by pressing .
slightly.
For example, to erase the third track
mark, find the beginning of the third
track. “00:00” appears in the display.
“MARK” appears in the display for a
few seconds.
3 Press T MARK to erase the mark.
Combining tracks
(Combine)
“MARK OFF” appears in the display.
The track mark is erased and the two
tracks are combined.
When you record with analog (line) input,
unnecessary track marks may be recorded
where recording level is low. You can
erase a track mark to combine the tracks
before and after the track mark.
z
When a track mark is erased when you combine
two tracks, the title and the recording date of
the second track changes to those of the first
track.
The track numbers will change as follows.
Note
1
2
3
4
3
When you erase a track mark between the two
consecutive tracks that are assigned into
different groups, the second track is re-assigned
into the group containing the first track. In
addition, if you combine a track that is assigned
to a group with a track that is not assigned to a
group (two consecutive tracks), the second
track takes the same registration setting as the
first track.
Erase a track mark
1
2
Track numbers decrease
Note
You cannot combine tracks if:
• one of the two tracks or the both tracks have
been transferred from the Windows computer.
• one of the two tracks or the both tracks have
been recorded in Hi-MD mode using the MD
Simple Burner software.
• the tracks are recorded in different recording
mode.
T MARK
X
.
54
Formatting the disc
(Format)
MENU
When using a disc in Hi-MD mode, you
can use the Format function to restore a
disc to the condition it was in at the time
of purchase.
Jog dial
You can use this function only when using
a disc in Hi-MD mode.
1 While the recorder is stopped, enter
the menu and select “Edit” -
“Format”.
Disc
type
After disc formatting
1GB
Hi-MD
disc
“NO TRACK” appears.
All data including non-audio
data will be erased.
“ALL DATA WILL BE DELETED”
appears in the display.
2 Turn the jog dial to select “OK”, and
then press the jog dial to enter the
selection.
NOTE: Transfer authorization
of the transferred tracks can be
restored by inserting the disc
into the recorder and
connecting the recorder to the
Windows computer.
“SYSTEM FILE WRITING” appears
in the display, and a disc will be
formatted.
When formatting completes, “NO
TRACK” appears in the display if a
1GB Hi-MD disc is inserted in the
recorder, or “BLANKDISC” appears
if a standard disc in Hi-MD mode is
inserted.
60/74/80- “BLANKDISC” appears.
minute All data including non-audio
standard data will be erased.
disc
NOTE: Transfer authorization
of the transferred tracks will
decrease by one.
Notes
• By formatting a disc, all data (including non-
audio data) will be erased. If you think a disc
contains such data, insert the disc into the
recorder and connect the recorder to the
computer to check the contents of the disc.
• If you format a disc, the transferred tracks on
the disc will also be erased and the number of
transfer authorizations for those tracks will be
decreased by one. To prevent the reduction in
transfer authorizations, restore the transfer
authorization by transferring the tracks to the
Windows computer again before formatting
the disc.
• The operation mode set in the “Disc Mode”
menu is applied to a blank 60/74/80-minute
standard disc used on the recorder even if a
different operation mode was selected in the
SonicStage software or a different operation
mode appeared on the display after the disc
was formatted by the SonicStage software.
55
Other operations
1 Enter the menu and select “Option” -
Changing the displayed
menu items (Menu
Mode)
“AVLS”.
2 Turn the jog dial to select “On”, and
then press the jog dial to enter the
selection.
You can specify the display of all items in
the menu (Advanced mode) or only basic
items (Simple mode).
check the menu items that cannot be
displayed.
When you try to turn the volume too
high, “AVLS NO VOLUME
OPERATION” appears in the display.
The volume is kept to a moderate
level.
MENU
To cancel the AVLS
Select “Off” in step 2.
Turning off the beep
sound
Jog dial
1 Enter the menu and select “Option” -
You can turn off/on the beep sound on the
recorder and the remote control.
“Menu Mode”.
2 Turn the jog dial to select
“Advanced” or “Simple”, and then
press the jog dial to enter the
selection.
MENU
Jog dial
Protecting your hearing
(AVLS)
1 Enter the menu and select “Option” -
“Beep”.
The AVLS (Automatic Volume Limiter
System) function prevents the volume
from being raised above a given level to
minimize sound leakage, sound pressure
on the ears and the danger connected with
the failure to hear important exterior
sounds.
2 Turn the jog dial to select “Off”, and
then press the jog dial to enter the
selection.
To turn on the beep sound
Select “On” in step 2.
MENU
Jog dial
56
Notes
Storing the settings for
individual discs (Disc
Memory)
• Settings for up to 64 discs can be stored. Any
settings stored afterwards will replace the
settings with the lowest frequency of use
among the 64. The numbers of discs that can
be stored depend on the numbers of tracks
recorded on the discs. More tracks recorded
per disc means fewer discs can be stored.
• If you try to erase the disc information of a
disc that have never been stored, “NO DISC
MEMORY” appears in the display for a few
seconds.
The recorder is factory set to
automatically store settings for each disc.
The recorder automatically stores the
settings for a disc and retrieves them
whenever the disc is inserted.
The following setting can be stored:
• Bookmark
• “Custom 1” and “Custom 2” settings of
6-Band Equalizer (for models except
European models)
Starting the playback
quickly (Quick Mode)
You can check the setting as follows.
MENU
The recorder is factory set to quickly start
playback after the playback button is
pressed.
You can check the setting as follows.
MENU
Jog dial
1 Remove the disc from the recorder,
enter the menu and select “Option” -
“Disc Memory”.
Jog dial
2 Turn the jog dial to select “On”, and
then press the jog dial to enter the
selection.
1 While the recorder is stopped or
playing, enter the menu and select
“Option” - “Quick Mode”.
To set the recorder so that
disc settings are not stored
2 Turn the jog dial to select “On”, and
then press the jog dial to enter the
selection.
Erasing the disc information
If you will not use the recorder
for a long time
You can minimize battery drain while the
recorder is not being used.
1 Insert the disc whose information is
to be erased and verify its contents.
The disc information is erased.
Note
When “Quick Mode” is set to “On”, power
continues to flow in the recorder even when it is
not being operated. The power is automatically
cut off when the batteries become drained.
57
Selecting the disc
mode (Disc Mode)
Adjusting the contrast
of the display window
(Contrast Adjustment)
When you insert a 60/74/80-minute
standard disc (blank) into the recorder,
you can use this function to specify use of
the disc in Hi-MD mode or MD mode.
When recording on this recorder without
using a computer, set “Disc Mode” to
“Hi-MD”. Recording is not possible if
“Disc Mode” is set to “MD”. To allow a
disc recorded on this recorder to be used
on another component that does not
support Hi-MD, set “Disc Mode” to
“MD” and use a Windows computer to
record in MD mode (refer to the
You can adjust the contrast of the display
window.
MENU
Jog dial
1 While the recorder is stopped, enter
the menu and select “Option” -
“Contrast”.
“Software Operation” section).
2 Turn the jog dial to adjust the
contrast, and then press the dial to
enter the selection.
MENU
Jog dial
1 Enter the menu and select “Option” -
“Disc Mode”.
2 Turn the jog dial until “Hi-MD”
(factory setting) or “MD” appears in
the display, and then press the dial to
enter the selection.
Notes
• Even if you select “MD” as the “Disc Mode”
setting, the operation mode can only be “Hi-
MD” when using a 1GB Hi-MD disc.
• The operation mode set in the “Disc Mode”
menu is applied to a blank 60/74/80-minute
standard disc used on the recorder even if a
different operation mode was selected in the
SonicStage software or a different operation
mode appeared on the display after the disc
was formatted by the SonicStage software.
58
Changing the
Selecting the display
language
operational direction of
the display
You can select the language used in the
display window.
The following languages are available.
English (factory setting), French,
German, Italian and Spanish
When you turn the jog dial downward, the
display scrolls downward. This is the
factory setting. You can change the
factory setting to scroll in the opposite
direction.
MENU
MENU
Jog dial
Jog dial
1 Enter the menu and select “Option” -
1 Enter the menu and select “Option” -
“Language”.
“Jog Dial”.
2 Turn the jog dial to select the desired
language, and then press the jog dial
to enter the selection.
2 Turn the jog dial to select “Reverse”,
and then press the jog dial to enter the
selection.
To turn the setting to normal
Select “Default” in step 2.
59
Using the recorder with a computer
z
If you play audio files using the SonicStage
What you can do
through connection
with a computer
software, the sound is output from the computer
speakers when a disc used in Hi-MD mode is
inserted, and from the earphones connected to
the recorder when a disc used in MD mode is
inserted in the recorder.
To use the recorder connected to a
computer, you must install the software
from the supplied CD-ROM. For details
on the installation procedure, refer to the
“Software Operation” (page 86) section
(if you are using Windows) or the “Hi-
MD WAV Importer for Mac” operating
instructions (if you are using Macintosh).
Charging the rechargeable
battery of the recorder
You can charge the rechargeable battery
while the recorder is connected to a
computer (using USB bus power).
When you connect the recorder to the
computer, power (bus power) from the
computer begins to charge the recorder’s
rechargeable battery. However, this
charge is only provisional and cannot be
used to fully charge the rechargeable
battery. For example, if you charge a
completely drained rechargeable battery
in this way, the recorder will stop
charging after about 6 hours when the
battery level is between half and full
charge. The charging time may vary
according to the condition of the
When using the supplied
software
• SonicStage for Windows
The SonicStage software enables you to
transfer audio data between the recorder
and the computer. When a disc used in
Hi-MD mode is inserted in the recorder,
tracks recorded with a microphone or
from a CD player to the recorder can
also be migrated to your computer. (See
online help.)
• MD Simple Burner for Windows
The MD Simple Burner software
enables you to record a CD in the
computer’s CD drive directly to a disc in
the recorder. (See the “Software
Operation” section.)
rechargeable battery and the surrounding
temperature.
You can check the USB bus power
charging with the battery indication.
• Hi-MD WAV Importer for Macintosh
The Hi-MD WAV Importer software
enables you to import audio data
recorded in linearPCM on the recorder
to a Macintosh computer. (See the
supplied “Hi-MD WAV Importer for
Mac” operating instructions.)
Note
Charging by USB bus power charge is not
possible when the battery level indication
When using the disc in the
recorder as a storage device
(
) is flashing in the display.
When a disc used in Hi-MD mode is
inserted in the recorder, the recorder
appears on the computer display as an
external drive, allowing you to transfer
non-audio data such as text and image
files. For details, refer to “Storing non-
• Reinsert the rechargeable battery and close the
battery compartment lid firmly.
• The temperature of the battery-charging
location is too low or too high. The
rechargeable battery should be charged within
a temperature range of +5°C (+41°F) to
+35°C (+95°F).
60
1 Insert a recordable disc into the
Connecting the
recorder to your
computer
recorder.
2 Make sure the recorder is stopped and
HOLD is released.
When you connect the supplied USB cable
directly to the USB connecting jack on the
recorder, power (bus power) is supplied
from the USB port of the computer. This
allows the recorder to be used without
power being supplied from the battery.
3 Open the cover of the
USB
connecting jack on the recorder and
connect the supplied USB cable to the
recorder and to the computer.
4 Check the connections.
When the connections have been
properly made, “PC – – MD” appears
in the display.
Note
When using Windows ME or Windows 98SE
• If you connect the recorder to the computer
with the disc mode on the recorder set to “Hi-
MD” (factory setting), and then insert a 60/74/
80-minute standard disc, the operation mode
of the disc may automatically change to Hi-
MD mode even if you do not record anything.
• When you disconnect the USB cable, the
message “Unsafe Removal of Device” appears
in the computer display. This is not a problem.
Merely click “OK” to make the message
disappear.
When you unplug the USB
cable from the computer or
remove the disc from the
recorder
Be sure to remove the recorder or the disc
as follows. If not, damage to the data may
occur.
Computer
1 If you are using a Macintosh
To the USB port
computer, drag the
([NO NAME]
icon) on the desktop to the trash can.
If you are using a Windows computer,
skip this step.
USB cable
(supplied)
2 Make sure that the “REC” indication
is not displayed in the display
window of the recorder.
To the
USB cable
connecting jack
3 Press x on the recorder.
“EJECT DISC OK” appears in the
display.
Depending on the conditions, it may
take some time until “EJECT DISC
OK” appears in the display.
Make sure to
open the cover.
61
4 Unplug the USB cable from the
computer or remove the disc from the
recorder.
Storing non-audio data
to a disc
If you connect the recorder to a computer
with a disc in Hi-MD mode inserted, the
disc is recognized as storage media by the
computer, allowing you to store non-
audio data such as text data or image data.
For the storage space for each disc, refer
to the next page.
Notes
• If you use the recorder connected to the
computer, it is recommended that you insert a
fully charged rechargeable battery as a
precaution against power failures,
disconnection of the USB cable or other
unforeseen occurrences. We do not assure the
results should there be a mis-operation,
transfer failures, or destruction of audio data
caused by unforeseen occurrences.
• If you disconnect the USB cable from the
recorder and want to reconnect it, make sure
to wait at least 2 seconds before connecting it
again.
• Make sure to place the recorder at a stable,
vibration-free place during recording.
• Make sure not to connect the recorder to your
computer during recording or playing.
• Make sure to turn off any system suspend,
sleep, or hibernation function that may be
active on your computer. If the computer
changes to any of these modes while
connecting with the recorder, a malfunction
may occur; for example, the computer may
not recognize the recorder. If this happens,
reconnect the USB cable.
When you insert a disc in Hi-MD mode
into the recorder and make connection
with the computer, the recorder is
recognized as an external device and can
be viewed on the computer display. You
can use the recorder in the same way as
other devices.
z
You can view non-audio data stored on a disc in
the display window of the recorder. For details,
Notes
• Make sure not to connect the recorder and the
• When the SonicStage software is active, the
recorder is not recognized as a data storage
device.
• To format a disc on the computer, follow the
instructions below.
—If you are using a Windows computer,
format the disc with the SonicStage
software.
—If you are using a Macintosh computer, you
cannot format a disc on the computer.
• Make sure not to delete the file management
folder (HMDHIFI folder and HI-MD.IND
file) on the computer.
computer through a USB hub.
• When the recorder is connected to a computer,
power (bus power) is supplied to the recorder
through the computer’s USB port. If the
computer (a laptop PC, for example) is
operating on battery power, this connection
may cause the computer’s battery to drain. It
is thus recommended to use the computer with
an AC power adaptor.
• We do not ensure trouble-free operation on all
computers that satisfy the system
requirements.
62
1 While the recorder is stopped, enter
Viewing non-audio data
stored on the disc in
the display window of
the recorder (File List)
the menu and select “File List”.
The root directories appear in the
order saved.
Disc name
When using a disc in Hi-MD mode, you
can view non-audio data stored on the
disc in the display window of the
recorder. The name and size of files are
displayed.
x
A list of
files and
folders is
displayed.
Root
directory
(first level)
Sub-
directory
(2nd level)
Sub-
directory
(3rd level)
2 Turn the jog dial to select the file you
want to confirm, and then press the
jog dial to enter the selection.
File size appears.
x
File size
appears
If you want to go deeper, select the
folder containing the file you want to
check, and then press the jog dial. A
list of files and folders in the selected
folder appears in the display.
: Directory
: File
• Up to 16 levels of directories can be
viewed.
Afterwards, perform the operation in
• Up to 512 files or folders can be viewed
in a root directory in the order saved.
• Up to 1,024 files or folders can be
viewed in each sub-directory.
Notes
• This function cannot be used to open files.
• Text containing characters that are not
supported by the recorder will not be
displayed correctly.
• File or directory names more than 9 characters
long will be shortened.
MENU
• If you select “File List” while playing or
recording a track, “CANNOT SET” appears in
the display and no list will appear.
Jog dial
63
The storage space for each disc (formatted with the recorder/the
SonicStage software)
Disc type
Total size
Disc management
space1)2)
Free space
60-minute
standard disc
219 MB
(229,965,824 bytes)
832 KB
(851,968 bytes)
218 MB
(229,113,856 bytes)
74-minute
standard disc
270 MB
(283,312,128 bytes)
832 KB
(851,968 bytes)
269 MB
(282,460,160 bytes)
80-minute
standard disc
291 MB
(305,856,512 bytes)
832 KB
(851,968 bytes)
290 MB
(305,004,544 bytes)
1GB Hi-MD disc 964 MB
832 KB
963 MB
(1,010,761,728 bytes)
(1,011,613,696 bytes) (851,968 bytes)
1) This is space that is used for managing the files on the disc.
2) The size of the disc management space changes according to the operating conditions of your computer
and other factors. Therefore, the actual space available for use may be lower than that displayed on the
computer display.
64
Additional information
• Never wrap the recorder in anything when it is
being used with the AC power adaptor. Heat
build-up in the recorder may cause
malfunction or damage.
Precautions
On safety
Do not put any foreign objects in the DC IN 3V
jack.
On the earphones
Road safety
Do not use earphones while driving, cycling, or
operating any motorized vehicle. It may create
a traffic hazard and is illegal in many areas. It
can also be potentially dangerous to play your
recorder at high volume while walking,
especially at pedestrian crossings. You should
exercise extreme caution or discontinue use in
potentially hazardous situations.
On power sources
• Use house current, nickel metal hydride
rechargeable battery, or LR6 (size AA)
battery.
• For use in your house: Use the AC power
adaptor supplied with this recorder. Do not
use any other AC power adaptor since it may
cause the recorder to malfunction.
Preventing hearing damage
Avoid using earphones at high volume. Hearing
experts advise against continuous, loud and
extended play. If you experience a ringing in
your ears, reduce the volume or discontinue
use.
Polarity of the plug
• Connect the AC power adaptor to an easily
accessible AC outlet. Should you notice an
abnormality in the AC power adaptor,
disconnect it from the AC outlet immediately.
• The recorder is not disconnected from the AC
power source (mains) as long as it is
Caring for others
Keep the volume at a moderate level. This will
allow you to hear outside sounds and to be
considerate of the people around you.
connected to the wall outlet, even if the
recorder itself has been turned off.
On the remote control (except
for the North American model)
The supplied remote control is designed for use
with this recorder only. The recorder cannot be
operated with a remote control that was
supplied with another device.
• If you are not going to use this recorder for a
long time, be sure to disconnect the power
supply (AC power adaptor, dry battery, or
rechargeable battery). To remove the AC
power adaptor from the wall outlet, grasp the
adaptor plug itself; never pull the cord.
On heat build-up
On charging
Heat may build up in the recorder if it is used
for an extended period of time. This, however,
is not a malfunction.
• Do not charge any other battery beside the
supplied one or the one designated for it (NH-
10WM).
• Be sure to use the supplied AC power adaptor.
• Charge the rechargeable battery at a
temperature of +5°C (+41°F) to +35°C
(+95°F).
• The recorder may become hot during the
charging procedure; this, however poses no
danger.
On installation
• If you use the recorder at a place subject to
static or electrical noise, the recording may
not be properly done or the recorded data may
be lost. If you perform a transfer operation at
such a place, the track’s transfer authorization
may be lost.
• Never use the recorder where it will be
subjected to extremes of light, temperature,
moisture or vibration.
65
• Because of the battery’s characteristics, the
capacity of the rechargeable battery may be
smaller than normal when it is used for the
first time or after a long period of disuse. In
this case, charge and discharge the battery
several times. The normal battery life will be
restored.
• If the capacity of the rechargeable battery
drops to half the normal amount, replace with
the new one.
On batteries
Incorrect battery usage may lead to leakage of
battery fluid or bursting battery. To prevent
such accidents, observe the following
precautions:
• Install the + and – poles of the batteries
correctly.
• When the recorder is not to be used for a long
time, be sure to remove the batteries.
• If a battery leak should develop, carefully and
thoroughly wipe away battery fluid from the
battery compartment before inserting new
ones.
• If the recorder will be unused for a long time,
remove the rechargeable battery and remove
the AC power adaptor from the wall outlet.
On the dry battery case
On mechanical noise
The supplied dry battery case is designated for
this recorder only.
The recorder gives off mechanical noise while
operating, which is caused by the power-saving
system of the recorder and it is not a problem.
On the MiniDisc cartridge
• When carrying or storing the MiniDisc, keep
it in its case.
• Do not break open the shutter.
• Do not place the cartridge where it will be
subject to light, extreme temperatures,
moisture or dust.
To protect a recorded disc
To record-protect a disc, slide open the tab at
the side of the disc. In this position, the disc
cannot be recorded. To record again, slide the
tab back so the tab is visible.
• Attach the supplied disc label only in the
space designated for it on the disc. Do not
stick it on any other disc surface.
Tab
On cleaning
• Clean the recorder casing with a soft cloth
slightly moistened with water or a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent such
as alcohol or benzene as it may mar the finish
of the casing.
Recorded material is
protected.
Back of the disc
• Wipe the disc cartridge with a dry cloth to
remove dirt.
• Dust on the lens may prevent the unit from
operating properly. Be sure to close the disc
compartment lid after inserting or ejecting a
disc.
Recorded material is
not protected.
• To obtain the best sound quality, use a dry
cloth to wipe the plugs of the earphones or the
remote control. Dirty plugs may cause sound
distortion or intermittent breaks in the sound.
On maintenance
Clean the terminals periodically with a cotton
swab or a soft cloth.
If you have any questions or problems
concerning your recorder, please consult your
nearest Sony dealer. (If a trouble occurred when
the disc was in the recorder, we recommend that
the disc be left in the recorder when you consult
your Sony dealer so that the cause of trouble
may be better understood.)
66
Inputs1)
MIC: stereo mini-jack
(minimum input level 0.13 mV)
Specifications
Audio playing system
MiniDisc digital audio system
Systems
Line in:
stereo mini-jack for analog input
(minimum input level 49 mV)
optical (digital) mini-jack for optical
(digital) input
MiniDisc system, Hi-MD system
Laser diode properties
Emission duration: continuous
Laser output: less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the lens surface on the optical
pick-up block with 7 mm aperture.)
Recording and playback time
Outputs
i: stereo mini-jack (dedicated remote control
jack)
Maximum output (DC)
Headphones:
2.8 mW + 2.8 mW (16 Ω) (European
models)
5 mW + 5 mW (16 Ω) (Other models)
Power requirements
Sony AC Power Adaptor connected at the DC
IN 3V jack:
Revolutions
Approx. 350 rpm to 3,000 rpm (CLV)
Error correction
120 V AC, 60 Hz (Models for USA, Canada,
Mexico and Taiwan)
Hi-MD:
LDC (Long Distance Code)/BIS (Burst
Indicator Subcode)
MD:
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Sampling frequency
44.1 kHz
Sampling rate converter
Optical (digital) input: 32 kHz/44.1 kHz/
48 kHz
Audio formats supported by this
recorder
Recording:
LinearPCM (44.1 kHz/16 bit)
ATRAC3plus (Adaptive TRansform
Acoustic Coding 3 plus) (Hi-SP/Hi-LP)
Playback:
LinearPCM
ATRAC3plus
240 V AC, 50 Hz (Model for Australia)
220 V AC, 50 Hz (Models for China and
Argentine)
100 - 240 V AC, 50/60 Hz (Other models)
The recorder:
Nickel metal hydride rechargeable battery
NH-10WM 1.2V 900 mAh (MIN) Ni-MH
LR6 (size AA) alkaline battery
AC power adaptor DC 3V
Operating temperature
+5°C (+41°F) to +35°C (+95°F)
Battery operation time2)
Dimensions
Approx. 80.2 × 20.7 × 84.3 mm (w/h/d)
(31/4 × 27/32 × 33/8 in.) (excluding projecting
parts and controls)
Mass
Approx. 112 g (4.0 oz) (the recorder only)
Approx. 138 g (4.9 oz) (including the
rechargeable battery)
ATRAC3
ATRAC
MP3 (MPEG-1 Audio Layer-3/Sampling
frequency 44.1 kHz/Bit rate 32 - 320 kbps
(constant/variable bit rate))
Modulation system
Hi-MD:
1-7RLL (Run Length Limited)/PRML
(Partial Response Maximum Likelihood)
MD:
1)The LINE IN (OPT) jack is used to connect
either a digital (optical) cable or a line
(analog) cable.
2)Measured in accordance with JEITA.
US and foreign patents licensed from Dolby
Laboratories.
EFM (Eight to Fourteen Modulation)
Frequency response
20 to 20,000 Hz 3 dB
Design and specifications are subject to change
without notice.
67
Optional accessories
Optical Cable
POC-15B, POC-15AB
Line Cable
RK-G129, RK-G136
MDR-series Stereo Headphones/earphones*
SRS-series Active Speakers
Recordable MDs MDW-series
Recordable Hi-MD disc
HMD1G
Nickel metal hydride rechargeable battery
NH-10WM
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
∗ When using optional headphones, use only
headphones/earphones with stereo mini
plugs. You cannot use headphones/
earphones with micro plugs.
68
Troubleshooting and explanations
Troubleshooting
If a problem occurs during recorder operation, follow the steps described below before
consulting the nearest Sony dealer. If any messages appear, it is recommended to take
notes.
2 ICfhaefctekr“sMtepes1saygoeus”st(ipllagcaen7n7o)tfsoorlvtheethperopbrloebmleams,wcoelnls.ult your nearest Sony dealer.
While charging
Symptom
Cause/Remedy
The rechargeable
battery does not start
charging. The
rechargeable battery
cannot be fully
charged.
• The rechargeable battery has been inserted incorrectly or the AC
power adaptor has been connected incorrectly.
, Insert the rechargeable battery correctly or connect the AC
power adaptor correctly.
• Because of the battery’s characteristics, the capacity of the
rechargeable battery may be smaller than normal when it is used for
the first time or after a long period of disuse.
, Charge and discharge the battery several times. The normal
battery life will be restored.
• The surrounding temperature is too high or too low.
, Charge the battery at a temperature of +5°C (+41°F) to +35°C
(+95°F).
• You charged the rechargeable battery using USB bus power.
, USB bus power charging is only provisional and cannot be used
to fully charge the rechargeable battery. Disconnect the recorder
from the computer and charge the rechargeable battery with the
AC power adaptor.
The rechargeable
battery has become
drained even when the
recorder was not used
for a while.
• The Quick mode was set to “On”.
, If you set the Quick mode to “On”, the power stays on inside
recorder even when there is no operation, causing the
battery is not fully charged, the battery may become drained
after a while. If this happens, charge the rechargeable battery
Even when fully
• The useful life of the rechargeable battery may be ending.
, Replace the rechargeable battery with the new one.
charged, the life of the
battery is only about
half what it normally is.
The recorder become
hot during the charging
procedure.
• This is normal and poses no danger.
69
While recording
Symptom
Cause/Remedy
“NOT ENOUGH
• Recording is not possible when using a 1GB Hi-MD disc even when
the battery level indication shows enough power remaining while the
recorder is stopped or playing. This is because of a mechanism that
disables recording when the remaining battery power is estimated by
the recorder to be insufficient due to the high power consumption
required for 1GB Hi-MD disc recording.
POWER TO REC”
appears and recording
cannot be done on a
1GB Hi-MD disc.
, Connect the AC power adaptor to the recorder or insert a fully
charged rechargeable battery or a new alkaline dry battery.
The remaining
recording time appears
as “–00:00” and
• This is a system limitation. 2.0MB is the capacity of the reserve
domain.
recording cannot be
done, even though
2.0MB of free space is
displayed.
The recorder always
creates a new group
when recording.
• The group recording (“Group REC”) is set to “On”. (You cannot
overwrite tracks.)
The first few seconds • If you start recording before the x indication appears in the display,
of a track cannot be
recorded.
data will not be recorded to the first few seconds of the first track.
, Wait until the x indication appears before you start recording.
Recording cannot be
done correctly.
• You tried to record in MD mode on this recorder.
,
Only Hi-MD mode can be used to record directly on this recorder
without using a computer. To record in MD mode, connect the
recorder to a Windows computer and use the supplied SonicStage
• Audio sources may not be securely connected.
, Disconnect the audio sources once and connect them again
• There is no digital signal from the portable CD player.
, When recording digitally from a portable CD player, use the AC
power adaptor and disable the anti-skip function (such as ESP)
on the CD player.
• The analog recording was made using a connecting cord with an
attenuator.
, Use a connecting cord without an attenuator.
• Recording level is too small to record (when adjusting the recording
level manually).
• The recorder is connected to the computer.
, Disconnect the recorder from the computer when recording.
• The power sources was disconnected or a power outage occurred
during recording.
, The recording result is not recorded on the disc. Make recording
again.
• Recording may not be done if the remaining recordable time on the
disc is 48 seconds or less (“DISC FULL” appears).
, Replace the disc.
70
Symptom
Cause/Remedy
The lid does not open • The lid does not open until “SYSTEM FILE WRITING” disappears
after recording.
in the display.
“TRACK FULL”
• This is due to the MiniDisc system limitation. When 2,047 tracks (on
appears even before the a disc used in Hi-MD mode) have been recorded on the disc,
disc has reached the
maximum recording
time and the recording
cannot be done.
“TRACK FULL” appears regardless of the total recorded time. More
than 2,047 tracks cannot be recorded on the disc.
, To continue recording, erase unnecessary tracks.
The remaining
• This is due to the MiniDisc system limitation (in MD mode only).
recording time does not Tracks of under 12 seconds (in SP mode), 24 seconds (in LP2 mode
increase even after or monaural), or 48 seconds (in LP4 mode) in length are not counted
erasing numerous short and so erasing them may not lead to an increase in the recording
tracks. time.
The total recorded time • This is due to the MiniDisc system limitation (in MD mode only).
and the remaining time Normally, recording is done in minimum units of approximately 2
on the disc may not
total the maximum
seconds (in SP mode), 4 seconds (in LP2 mode or monaural), or 8
seconds (in LP4 mode). When recording is stopped, the last unit of
recording time (60, 74, recording always uses this unit of 2 seconds, 4 seconds, or 8 seconds
or 80 minutes).
even if the actual recording is shorter. Likewise, when recording is
restarted after the stop, the recorder will automatically insert a blank
space amounting to 2 seconds, 4 seconds, or 8 seconds before the
next recording. (This is to prevent accidental erasing of a previous
track whenever a new recording is started). Therefore, the actual
recording time will decrease whenever a recording is stopped by a
maximum of 6 seconds, 12 seconds, or 24 seconds.
“TRACK FULL”
• This is due to the MiniDisc system limitation. Repeated recording
appears even before the and erasing may cause fragmentation and scattering of data.
disc has reached the
maximum track
number or recording
time.
Although those scattered data can be read, each fragment is counted
as a track. In this case, the number of tracks may reach 2,047 (on a
disc used in Hi-MD mode) and further recording is not possible.
, To continue recording, erase unnecessary tracks.
While playing
Symptom
Cause/Remedy
A disc is not played
normally.
• Repeat play is selected.
, Set the Repeat play to “Off” to change back to the normal play
• Playback mode is changed.
, Enter the Main play mode or Sub play mode to change back to
the normal play (page 40).
A disc is not played
from the first track.
• Disc playing stopped before it came to the last track.
, Press the jog dial (N/ENT) on the recorder or press NX on
the remote control for 2 seconds or more to start playing.
71
Symptom
Cause/Remedy
Playback sound skips. • The recorder is placed where it receives continuous vibration.
, Put the recorder on a stable place.
• A very short track may cause sound to skip.
, Try not to create a short track.
Momentary noise is
heard.
• Due to the special digital audio compression technology used in
LP4 mode, momentary noise may occur on very rare occasions with
certain sound sources.
Sound has a lot of static. • Strong magnetism from a television or such device is interfering
with operation.
, Move the recorder away from the source of strong magnetism.
The volume of the
recorded track is low.
• The track was recorded in analog mode (in digital mode, the
recording level is automatically set to the same level as that of the
sound source). Or you used a connecting cord with an attenuator.
, Use a correct connecting cord without an attenuator.
• The recording level was low.
Volume cannot be
turned up.
• AVLS is on.
No sound comes
through the earphones.
• The earphones plug is not firmly connected.
, Plug in the plug of the earphones or the remote control firmly to
the appropriate jacks.
• The plug is dirty.
, Clean the plug.
The disc cannot be
played on another
component.
• The component does not support Hi-MD.
, Discs recorded on this recorder can be played only on
components that support Hi-MD.
The edited tracks may • This occurs due to the MiniDisc system limitation. The
exhibit sound dropout
during search
fragmentation of data may cause sound dropout while searching
because the tracks are played in higher speed than normal playback.
operations.
There is no R-channel • There is no R-channel output if the cassette deck or an amplifier is
sound output when connected with a monaural cord.
playing a track recorded , Make sure to use a stereo connecting cord. If, however, the
from a cassette deck or
through an amplifier, or
when listening to sound
from a cassette deck or
amplifier.
connected equipment is monaural, there will be no R-channel
sound output even with a stereo connecting cord.
The recorder cannot
play MP3 tracks.
• You tried to play an MP3 track with a format not supported by this
recorder.
, This recorder only supports MP3 tracks (MPEG-1 Audio Layer-
3/Sampling frequency 44.1 kHz) that have been transferred
using the SonicStage software.
“R” appears in the
display window during
playback.
• “R” appears when the contents of an editing operation performed
during recorder playback are ready to be written to the disc.
, When playback on the recorder is stopped, the edited contents
are written to the disc and the “R” disappears.
72
While editing
Symptom
Cause/Remedy
“NOT ENOUGH
POWER TO EDIT”
appears and editing
cannot be done on a
1GB Hi-MD disc.
• Editing is not possible when using a 1GB Hi-MD disc even when the
battery level indication shows enough power remaining while the
recorder is stopped or playing. This is because of a mechanism that
disables editing when the remaining battery power is estimated by
the recorder to be insufficient due to the high power consumption
required for 1GB Hi-MD disc editing.
, Connect the AC power adaptor to the recorder or insert a fully
charged rechargeable battery or a new alkaline dry battery.
The lid does not open. • The recorder is saving the contents of an editing operation. The lid
will not open until “SYSTEM FILE WRITING” disappears from the
display.
Editing cannot be done. • The power source has been disconnected or a power outage has
occurred during editing.
, The editing done to that point is not saved to the disc. Do the
editing operation again.
Non-audio data cannot • Non-audio data cannot be erased with the Erase function.
be erased.
, Confirm the contents by connecting the recorder to your
computer. If it is okay to delete the contents, then perform the
Format function (page 55).
Tracks cannot be
combined.
• This is due to the MiniDisc system limitations. When the tracks are
scattered and the length of each track is short*, you may not be able
to combine the tracks.
* Combining tracks of the following lengths may not be possible.
Hi-MD mode
LinearPCM: 9 seconds or less
Hi-SP: 8 seconds or less
Hi-LP: 32 seconds or less
MD mode
SP: 12 seconds or less
LP2/Monaural: 24 seconds or less
LP4: 48 seconds or less
• You cannot combine tracks recorded in different recording modes,
e.g., a track recorded in stereo and a track recorded in monaural; nor
can you combine a track recorded with digital connection and a track
recorded with analog connection.
The disc cannot edit on • The component does not support Hi-MD.
other component. , Edit on other component that support Hi-MD.
While using group function
Symptom
Cause/Remedy
The group function does • While using a disc without group setting, an attempt was made to
not operate.
select some group-related menu.
, Use a disc with group setting.
73
Symptom
Cause/Remedy
A new group cannot be • This is due to the MiniDisc system limitations (in MD mode only).
created.
Group information has been written to the area where the disc name
is stored. The disc name and track names are recorded in the same
area, which can store a maximum of approximately 1,700
characters. If the total number exceeds this amount, it is impossible
to make group settings.
While the recorder is connected to the computer
Symptom
Cause/Remedy
The recorder is not • The supplied USB cable is not firmly connected.
, Connect the USB cable firmly to the recorder and the computer.
recognized by the
computer.
• A USB hub is used.
, Connect the USB cable directly to the USB port of the computer.
• Network communication has failed.
, Disconnect the USB cable, wait at least 2 seconds, and then
reconnect it. If the recorder is still not recognized, disconnect the
USB cable, restart the computer, and then connect the USB cable
again.
• When using Windows 2000 Professional, you turned on or restarted the
computer while the supplied USB cable was connected, and then
disconnected it afterwards.
, Disconnect the USB cable, restart the computer, and then reconnect
the USB cable. This problem may be resolved by updating your
Windows operating system so that it contains all the latest features.
Charging by USB
bus power cannot be
• The battery compartment lid is not firmly closed.
, Reinsert the rechargeable battery and close the battery compartment
lid firmly.
done (
flashes
• The temperature of the battery-charging location is too low or too high.
, Charge the rechargeable battery within a temperature range of +5°C
(+41°F) to +35°C (+95°F).
in the display).
The rechargeable
battery cannot be
charged sufficiently
through USB bus
power.
• The rechargeable battery is charged through USB bus power.
, USB bus power only charges temporary and cannot charge the
rechargeable battery sufficiently. Disconnect the recorder from the
computer and charge the rechargeable battery using the AC power
adaptor.
Even though the
recorder is
recognized by the
• A USB hub is used.
, Connect the supplied USB cable directly to the USB port of the
computer.
computer, it does not • You are using the recorder at a place with vibration.
operate normally. , Use the recorder at a place with no vibration.
The recorder cannot • The SonicStage or MD Simple Burner software is active.
be used as a storage
device.
, Close the SonicStage or MD Simple Burner software.
• A disc which is not used in Hi-MD mode is inserted.
, Insert a disc used in Hi-MD mode. Only discs used in Hi-MD mode
can be used as a storage media.
74
Symptom
Cause/Remedy
The playing time of This is due to a calculation discrepancy between the recorder and the
a transferred track is computer.
different from the
time that appears on
your computer
monitor.
You cannot transfer • The minimum recordable time on a disc is normally 2 seconds in SP
tracks that will fill
up the remaining
recording time on
the disc.
mode, 4 seconds in LP2 mode, and 8 seconds in LP4 mode. When you
transfer a track from your Windows computer, the recorder needs a 2-
second (or 4- or 8-second) space for a track even if the track is under 2
seconds (or 4 or 8 seconds) in length. Also, the recorder inserts a 2-
second (or 4 -or 8-second) space in between tracks during transfer
operation. For this reason, the recorder needs an additional 6 seconds
(or 12 or 24 seconds) for each track. This reduces the maximum
recording time for each track by 6 seconds (or 12 or 24 seconds) during
transfer operation (in MD mode only).
The disc size
displayed on the
computer is not the
• The difference is due to the use of the binary system to indicate the disc
size on the computer and the decimal system to express the disc size on
the disc and other recording media. For details on the disc size, see
printed on the disc.
You cannot operate • You cannot operate the recorder while the recorder is connected to the
the recorder.
computer.
The lid does not
open.
• It happens if you disconnect the supplied USB cable in the middle of a
data transfer, recording, or editing operation on the computer, but while
the rechargeable battery is missing from the recorder or is drained.
, Reconnect the USB cable or insert a fully charged rechargeable
battery into the recorder, and then press x.
Others
Symptom
Cause/Remedy
“Advanced” or
“Simple” is
displayed.
• You attempted to do a menu operation for the first time after purchase
of the recorder (by pressing the MENU button for 2 seconds or more).
Some menu items
cannot be displayed.
• “Menu Mode” is set to “Simple”.
, Set the “Menu Mode” to “Advanced” to display all the menu items.
The recorder does
not work or works
poorly.
• The rechargeable battery is not charged.
, Charge the rechargeable battery.
• The volume is low.
, Turn up the volume.
• No disc is inserted.
, Insert a recorded disc.
• The HOLD function is turned on (“HOLD” appears in the display when
you press an operation button on the recorder).
, On the recorder, disable HOLD by sliding the HOLD switch to the
75
Symptom
Cause/Remedy
The recorder does
not work or works
poorly.
• The lid is not firmly closed.
, Close the lid until it clicks. Then slide OPEN to open the lid.
• Moisture has condensed inside the recorder (for example, when the
recorder has been brought in from a cold place to a warm place).
, Take the disc out and leave the recorder in a warm place for several
hours until the moisture evaporates.
• The AC power adaptor is not firmly connected.
, Connect the AC power adaptor firmly to the DC IN 3V jack on the
recorder.
• The rechargeable battery or dry battery is weak (“LOW BATTERY”
flashes or nothing appears).
, Charge the rechargeable battery, replace the dry battery with a new
one, or use the supplied AC power adaptor.
• The disc is damaged or does not contain proper recording or editing data.
, Reinsert the disc. Rerecord the disc. If the error message still
appears, replace it with another disc.
• There is a built-in malfunction in the system.
• While operating, the recorder received a mechanical shock, too much
static, abnormal power voltage caused by lightning, etc.
, Restart the operation as follows.
1 Disconnect all the power sources and the USB cable.
2 Leave the recorder for about 30 seconds.
3 Connect the power source.
File names or folder • File names and folder names that exceed the maximum display length
names displayed by
the File list function
are different from
those saved on the
computer.
supported by the recorder are shortened.
The file names or
folder names are not
correctly displayed
by the File list
• The names contain characters that are not supported by the recorder.
function.
The operation mode • When using a blank 60/74/80-minute standard disc in the recorder, the
of the blank 60/74/
80-minute standard
disc differs from the
mode following
operation mode set in the “Disc Mode” menu is applied.
, Use the “Disc Mode” menu to change the operation mode as
desired.
formatting or the
mode selected in the
SonicStage software.
76
Messages
If the following messages appear in the display window on the recorder, check the chart
below.
Message
Meaning/Remedy
AVLS NO
VOLUME
OPERATION
• AVLS is set to “On” and so the volume cannot rise higher.
BLANKDISC
• A disc with no recording on it is inserted.
BUSY WAIT A • The recorder is accessing disc information.
MOMENT • You tried to operate the recorder while it was accessing the recorded data.
, Wait until the message goes out (in rare cases, it may take a few
minutes).
CANNOT EDIT • You selected, “Group Set”, “GroupRelease”, “Move”, or “Erase” while
recording.
• You tried to erase the track mark at the beginning of the first track or group.
• You tried to erase a track mark to combine tracks the recorder cannot
combine (a track recorded in stereo and in mono, for example).
• You tried to overwrite a track marks.
• You tried to change a title that includes characters the recorder cannot edit.
, Editing titles cannot be done if the title includes characters that cannot
be input on the recorder.
CANNOT
OPERATE
• You tried to press X or T MARK during synchro-recording.
CANNOT PLAY • You tried to play a track that is subject to play restrictions.
• You tried to play an MP3 track with a format not supported by this recorder.
, This recorder only supports MP3 tracks (MPEG-1 Audio Layer-3/
sampling frequency 44.1 kHz) that have been transferred using the
SonicStage software.
CANNOT
RECORD
• You tried to record on a disc that has already been recorded in MD mode.
, On this recorder, you cannot do additional recording on a disc that is
already recorded in MD mode. If you want to do additional recording
on such a disc, connect the recorder to a Windows computer and use the
supplied SonicStage or MD Simple Burner software.
CANNOT
RECORD OR
PLAY
• There is no audio data that can be played on the recorder.
• The audio data or disc management file has been damaged.
CANNOT SET
• You tried to set “Time Mark” during synchro-recording.
• You selected “REC Level” while the recorder is not in recording-pause.
, Set “REC Level” while the recorder is in recording-pause.
• You tried to make the following settings while recording.
— Recording mode
— Disc Memory
— Play mode
— Selection of “Group REC” in menu
Charging
• The rechargeable battery is being charged.
77
Message
Meaning/Remedy
DATA SAVE
• The recorder is writing information to the system file, such as the recorded
data or editing information.
, Wait until the message disappears from the display.
DC IN TOO
HIGH
• Voltage of the power supply is too high (The supplied AC power adaptor is
not used).
, Use the supplied AC power adaptor.
DISC FULL
• Recording may not be done if the remaining recordable time on the disc is
48 seconds or less.
, Replace the disc.
DOWNLOAD
READY
• MD Simple Burner is now ready to record an audio CD to the disc in the
EJECT DISC OK • The recorder has finished communicating with the computer and it is safe
to eject the disc from the recorder or disconnect the USB cable.
END
• The recorder reached to the end of the disc while playing or pressing >.
ERROR
• There is an internal malfunction in the system.
ERROR XX
• There is an internal malfunction in the system.
appears again, please consult your nearest Sony dealer.
FOLDER NO
EXPAND
• You tried to use the File List function to expand a folder that is already at
the 16th level.
, Files and folders can be expanded down to 16 levels. Expansion beyond
this level is not possible.
FORMAT
ERROR DISC
• A disc with a format that the recorder does not support was inserted.
, Insert a disc used in Hi-MD mode.
• A disc formatted on a computer was inserted.
, A disc formatted on a Windows or Macintosh computer cannot be used.
Format the disc on the recorder or with the SonicStage software.
GROUP FULL
• You tried to create a 256th group on a disc used in Hi-MD mode or 100th
group on a disc used in MD mode.
, You can create only up to 255 groups (on a disc used in Hi-MD mode)
or 99 groups (on a disc used in MD mode) on a disc. Keep the group
number within 255 or 99.
HOLD
• The recorder is locked.
IN MENU
• You pressed a key on the remote control while selecting a menu on the
recorder.
LOW BATTERY • Batteries are weak.
MEMORY
OVER
• You tried to record with the recorder placed where it receives continuous
vibration.
, Put the recorder on a stable place, and start recording again.
NO
• You selected bookmark play without setting bookmarks.
BOOKMARKED
TRACK
78
Message
Meaning/Remedy
NO DIGITAL
COPY
• You tried to make a copy from a disc that is protected by the Serial Copy
Management System. You cannot make copies from a digitally connected
source which was itself recorded using digital connection.
NO DISC
• You tried to play or record with no disc in the recorder.
, Insert a disc.
NO DISC
MEMORY
• You tried to erase a setting in the Disc Memory on a disc that contains no
NO FILE
• While viewing the file list, you selected a folder that have no folders or files
NO GROUP
• You selected “Group Erase” with a disc without group setting.
, You cannot erase groups with a disc with no groups.
• You tried to release a group setting with a disc that has no groups.
, Insert a disc with group settings.
NO INPUT
SIGNAL
• The recorder could not detect digital input signals.
NON GROUPED • You selected “Group Move” or “Group Erase”, or you tried to label a group
TRACK
while selecting a track that does not belong to a group.
, Select a track within a group you want to edit, and then do the editing
operation again.
NOT ENOUGH • You tried to edit the contents of a 1GB Hi-MD disc with insufficient battery
POWER TO
EDIT
power for editing (page 73).
, Connect the AC power adaptor to the recorder or insert a fully charged
rechargeable battery or a new alkaline dry battery.
NOT ENOUGH • You tried to record on a 1GB Hi-MD disc with insufficient battery power
POWER TO
REC
, Connect the AC power adaptor to the recorder or insert a fully charged
rechargeable battery or a new alkaline dry battery.
NO TRACK
• You tried to play a disc with no recorded tracks.
, Insert a recorded disc.
NO TRACK IS • You selected “Track Move” or “Track Erase”, or you tried to label a track
SELECTED
without first selecting a track.
, Do the editing operation again after selecting the desired track first.
P/B ONLY DISC • You tried to record or edit on a premastered disc (P/B stands for
“playback”).
, Insert a recordable disc.
PC – – MD
• The recorder is connected to the computer.
PROTECTED
DISC
• You tried to record or edit on a disc with the tab in the record-protect
position.
PUSH STOP
BUTTON
• You tried to open the lid by sliding the OPEN switch or operate the recorder
while the recorder was storing disc information with the supplied USB
cable connecting the recorder to a computer.
, Operation must be done only after pressing x and “SYSTEM FILE
WRITING” has disappeared from the display.
79
Message
Meaning/Remedy
READ ERROR • The recorder cannot read the disc information correctly.
, Reinsert the disc.
REC ERROR
• Recording was not correctly done.
, Place the recorder at a place with no vibrations and record again.
• The disc is soiled with an oil film or finger prints, is scratched, or is not a
standard disc.
, Try recording again with another disc.
SEARCH
• You pressed a button or a control on the remote control while using the
Search function on the recorder.
, Use the buttons and controls on the recorder.
SYSTEM FILE • The recorder is storing information (track start and end position) from the
WRITING
memory to the disk.
, Wait until this process is completed. Do not expose the player to
physical shock, nor disrupt power supply.
TEMP OVER
REC STOP
• Heat has built up in the recorder.
, Let the recorder cool down.
TITLE FULL
• You tried to enter more than 200 letters to label a single track, group, or
disc.
• You tried to enter a total of more than approximately 55,000 letters (in a
disc used in Hi-MD mode) or 1,700 letters (in a disc used inMD mode) for
titles.
TOC DATA
ERROR
• The recorder cannot read the disc information correctly.
, Insert another disc.
TRACK FULL
• You tried to record more than 2,047 tracks on a disc used in Hi-MD mode.
TRK FROM PC • You tried to combine or divide tracks that were transferred from the
NO EDIT
Windows computer.
, You cannot combine or divide transferred tracks.
• You tried to combine or divide tracks that were recorded in Hi-MD mode
using the MD Simple Burner software.
, You cannot combine or divide tracks recorded in Hi-MD mode with the
MD Simple Burner software.
TRK FROM PC • You tried to record in the middle of a protected track that has been
NO REC
transferred from the Windows computer.
• You tried to record in the middle of a track that was recorded in Hi-MD
mode with the MD Simple Burner software.
, You cannot record new material in the middle of a protected track or a
track that was recorded in Hi-MD mode with the MD Simple Burner
software.
80
Explanations
About Hi-MD
“Hi-MD” is a new MiniDisc format.
Incorporating the new ATRAC3plus audio compression technology, Hi-MD is a new recording format
that delivers longer recording times than ordinary MDs. Hi-MD discs can also be used as a computer
storage medium for non-audio data such as text and images. This recorder supports Hi-MD only.
For more details on Hi-MD, refer to the supplied flyer “What you can do with the Hi-MD Walkman”.
About ATRAC3plus
ATRAC3plus is an enhanced version of ATRAC3.
Compared to ATRAC3 (used in LP2 and LP4 recording mode of MiniDisc components), which attains
a compression ratio 10 times higher than that of a CD, ATRAC3plus (used in Hi-SP and Hi-LP mode of
the recorder) achieves a higher compression ratio that is 20 times higher than that of a CD, but with no
loss in sound quality.
“Hi-MD mode” and “MD mode”
This recorder has two operation modes, “Hi-MD mode” and “MD mode”. The operation mode is
automatically recognized whenever the disc is inserted.
• When using a 1GB Hi-MD disc, the operation mode will only be Hi-MD.
• When using a standard disc (60/74/80 minutes), the operation mode can be set as follows.
Disc condition
Operation mode
Blank disc
The mode set for the “Disc Mode” in the menu.1)
, When recording on this recorder without using a Windows
computer, set “Disc Mode” to “Hi-MD” so that the operation
mode will be “Hi-MD mode”.
The disc contains material
recorded in Hi-MD mode
Hi-MD
The disc contains material
recorded in MD mode
MD
, You cannot use this recorder to record in MD mode without
using a Windows computer. Recording in “MD mode” is
possible if you use the supplied SonicStage or MD Simple
Burner software.
About LinearPCM
LinearPCM is a digital, non-compressed audio coding system. You can enjoy high-quality sound equal
to that of CDs by recording in this mode.
The meaning of “no sound”
“No sound” describes a recorder condition in which the input level is about 4.8 mV during analog input
or less than –89 dB during optical (digital) input (with 0 dB as full bit (the maximum recordable level
for a MiniDisc)).
81
About “System File”
The system file is space on the disc that is used to store information other than audio files; for instance,
track numbers.
If the MiniDisc were a book, the system file would correspond with the index or table of contents.
The recorder rewrites the system file whenever an operation such as recording, adding or deleting track
marks, or moving tracks has been done. (“SYSTEM FILE WRITING” appears in the display when the
recorder is rewriting the system file.) While the recorder is writing disc information, make sure not to
move or jog the recorder or disconnect the power source as this may cause the information to be
incorrectly recorded or the disc contents to be lost.
List of the recording time for each disc
When using a disc in Hi-MD mode
When recording on the
recorder
Recording time1)
Recording
Codec/
1GB Hi-MD 80-minute
74-minute 60-minute
mode on the Bit rate
recorder
disc
standard
disc
standard
disc
standard
disc
PCM
LinearPCM/
1.4Mbps
1 hour and 34 28 minutes
minutes
26 minutes
21 minutes
Hi-SP
Hi-LP
ATRAC3plus/ 7 hours and 55 2 hours and 20 2 hours and 1 hour and 40
256kbps minutes minutes 10 minutes minutes
ATRAC3plus/ 34 hours
64kbps
10 hours and 9 hours and 7 hours and
10 minutes 20 minutes 40 minutes
When transferring from the
Windows computer
Codec/Bit rate
1GB Hi-MD 80-minute
74-minute 60-minute
disc
standard
disc
standard
disc
standard
disc
LinearPCM/1.4Mbps
ATRAC3plus/256kbps
ATRAC3plus/64kbps
ATRAC3plus/ 48 kbps
ATRAC3/132kbps
ATRAC3/105kbps
ATRAC3/66kbps
1 hour and 34 28 minutes
minutes
26 minutes
21 minutes
7 hours and 55 2 hours and 20 2 hours and 1 hour and 40
minutes
minutes
10 minutes
minutes
34 hours
10 hours and 9 hours and 7 hours and
10 minutes 20 minutes 40 minutes
45 hours
13 hours and 12 hours and 10 hours
30 minutes 30 minutes
16 hours and 4 hours and 50 4 hours and 3 hours and
30 minutes minutes 30 minutes 40 minutes
20 hours and 6 hours and 10 5 hours and 4 hours and
40 minutes
minutes
40 minutes
40 minutes
32 hours and 9 hours and 50 9 hours
7 hours and
20 minutes
40 minutes
17 hours
minutes
5 hours
MP3/128kbps
4 hours and 3 hours and
30 minutes
30 minutes
1) Approximate time
2) When transferring 4-minute tracks
82
When using a disc in MD mode
You cannot record in MD mode on this recorder.
When transferring from the
Windows computer
Recording time1)2)
74-minute 60-minute
Codec/Bit rate
80-minute
standard disc standard disc standard disc
ATRAC(stereo)/292kbps
ATRAC3/132, 105kbps
80 minutes
74 minutes
60 minutes
2 hours and 40
minutes
2 hours and 28 2 hours
minutes
ATRAC3/66kbps
5 hours and 20
minutes
4 hours and 56 4 hours
minutes
1) Approximate time
2) When transferring 4-minute tracks
About recordable audio formats
The audio formats that can be recorded on this recorder vary according to the disc type and recording
method. Check the following table for details.
Disc type
Recording
method
Format
Component used for playback
Component
Component
MD
that supports that supports component
Hi-MD1)
MDLP2)
1GB Hi-MD
disc
When recording
on the recorder
Hi-MD
When transferring Hi-MD
from the Windows
computer
60/74/80-
minute
When recording
on the recorder
Hi-MD
standard disc
When transferring Hi-MD
from the Windows
computer
MDLP
MD
1)Audio components marked with the
2)Audio components marked only with the
or
logo mark
or
logo mark
83
Note on digital recording
This recorder uses the Serial Copy Management System, which allows only first-generation digital
copies to be made from premastered software. You can only make copies from a home-recorded disc by
using the analog (line out) connections.
Premastered software such as CDs or MDs.
Microphone, record player, tuner, etc. (with
analog output jacks).
Analog recording
Digital recording
Home-recorded disc
Digital recording
Home-
recorded
disc
No
digital
recording
Recordable
disc
No
digital
recording
Recordable
disc
Recordable
disc
Restrictions on the editing of tracks transferred from your
Windows computer
This unit was designed so that editing functions (i.e., adding track marks and erasing track
marks) do not function for tracks that have been transferred from your Windows computer. This
is to prevent the loss of transfer authorization by the transferred tracks. To edit these tracks, first
transfer them into the computer, and then edit them on the computer.
About the DSP TYPE-S for ATRAC/ATRAC3
This recorder supports DSP TYPE-S, a specification for high-level Sony MiniDisc decks
equipped with digital signal processors (DSP). This specification allows the recorder to produce
high-quality sound from tracks recorded in MDLP mode. Since it retains DSP TYPE-R support,
the recorder produces superior results during playback in SP (normal stereo) mode.
Suppressing the skips of the sound (G-PROTECTION)
The G-PROTECTION function was developed to provide a higher level of shock resistance than
that of existing players.
84
Difference between digital (optical) and analog (line) inputs
The input jack of this recorder works as both digital and analog input jacks. Connect the
recorder to a CD player or a cassette recorder using either digital (optical) input or analog
record using analog (line) input.
Difference Digital (optical) input
Analog (line) input
Connectable Equipment with a digital (optical) output jack Equipment with an analog (line)
source
(CD player, DVD player, etc.)
output jack (Casette deck, radio,
record player, etc.)
Usable cord
Optical cable (with an optical or an optical-
mini plug) (page 21)
Line cable (with 2 phono plugs
or a stereo-mini plug) (page 34)
Signal from
the source
Digital
Analog
Even when a digital source
(such as a CD) is connected, the
signal sent to the recorder is
analog.
Track marks1) Marked (copied) automatically
Marked automatically
• at the same positions as the source (when the • after more than 2 seconds of
sound source is a CD or an MD).
• after more than 2 seconds of no sound
(page 81) or low-level segment (with a
sound source other than a CD or an MD).
• when the recorder is paused (3 seconds of no
sound is encountered while synchro-
recording)
level segment.
• when the recorder is paused
while recording.
Recorded
sound level
Same as the source.
Can also be adjusted manually (Digital REC also be adjusted manually
Adjusted automatically. Can
Note
Track marks may be copied incorrectly:
• when you record from some CD players or multi disc players using digital (optical) input.
• when the source is in shuffle or program play mode while recording using digital (optical) input. In
this case, play the source in normal play mode.
• when programs with audio that is digitally broadcast (e.g., digital TV) are recorded through the digital
(optical) input.
85
What you can do with SonicStage/
MD Simple Burner
Refer to the supplied “Hi-MD WAV Importer for Mac” operating instructions for details on
operations of the Hi-MD WAV Importer software.
What you can do with SonicStage
SonicStage allows you to import audio data to your computer from music sources such as
audio CDs and the Internet, and then transfer the audio data stored in your computer to an
MD.
Audio CD
MD Walkman
Transfer
Import
Music files in the
MP3,WAV, and
WMA* formats
Internet
∗ Copyright-protected WMA files cannot be transferred.
What you can do with MD Simple Burner
MD Simple Burner allows you to record music tracks from an audio CD in the CD drive of
your computer to an MD Walkman, without first recording the music tracks to the
computer.
MD Walkman
Audio CD
86
Basic operational flow using an MD Walkman
SonicStage
MD Simple Burner
Providing the required system environment (page 88)
Installing the software onto your computer (page 89)
Connecting an MD
Importing audio data to
your computer (page 91)
walkman to your
Connecting an MD
walkman to your computer
Recording music tracks
from an audio CD in the
CD drive of your
Transferring audio data
from your computer
Listening to an MD
87
Installing
Providing the required system environment
System requirements
The following system environment is required in order to use the SonicStage Ver. 3.1/MD
Simple Burner Ver. 2.0 software for the MD Walkman.
Computer
IBM PC/AT or Compatible
• CPU: Pentium III 450 MHz or higher
• Hard disk drive space: 200 MB or more (1.5 GB or more is
recommended) (The amount of free space will vary according to
Windows version and the number of music files stored on the hard
disk.)
• RAM: 128 MB or more
Others
• CD drive (capable of digital playback by WDM) (A CD-R/RW drive
is necessary for CD writing)
• Sound Board
• USB port
Operating
System
Factory installed:
Windows XP Media Center Edition 2005/Windows XP Media Center
Edition 2004/Windows XP Media Center Edition/Windows XP
Professional/Windows XP Home Edition/Windows 2000 Professional
(Service Pack 3 or later)/Windows Millennium Edition/Windows 98
Second Edition
Display
Others
High Color (16bit) or higher, 800 × 600 dots or better (1,024 × 768 dots
or better is recommended)
• Internet access: for Web registration, EMD services and CDDB
• Windows Media Player (version 7.0 or higher) installed for playing
WMA files
This software is not supported by the following environments:
• OSs other than those indicated above
• Personally constructed PCs or operating systems
• An environment that is an upgrade of the original manufacturer-installed operating system
• Multi-boot environment
• Multi-monitor environment
• Macintosh
Notes
• We do not ensure trouble-free operation on all computers that satisfy the system requirements.
• The NTFS format of Windows XP/Windows 2000 Professional can be used only with the standard
(factory) settings.
• We do not ensure trouble-free operation on computers which have changed to the system suspend,
sleep, or hibernation mode.
88
Installing the software onto your computer
Before installing the software
• Make sure to close all Windows software programs. Especially, make sure to close any
virus-check software, as such software usually demands a large amount of system
resources.
• When you use the MD Walkman, make sure to install the software with the supplied CD-
ROM.
— If OpenMG Jukebox, SonicStage or Net MD Simple Burner is installed already, the
current software will be overwritten by the new version. The new version retains the
functions of the older version, but with new functions added.
— If SonicStage Premium or SonicStage Simple Burner is installed already, the current
software will co-exist with the new version.
— You will still be able to use music data registered by the older software version even
after the new SonicStage has been installed. As a precaution, we recommend that you
back up your music data. To back up the data, refer to [Backing Up My Library] on
SonicStage Help.
The method for managing music data differs in part from conventional methods. For
details, refer to [For Users of Earlier Versions of SonicStage] in SonicStage Help.
• Make sure to install SonicStage before connecting the MD Walkman to the computer
with the supplied USB cable.
1 Turn on your computer and start up Windows.
2 Insert the supplied CD-ROM into the CD drive of your computer.
The setup program starts up automatically and the installation window appears.
3 When the [Region Selection] screen appears, select the region where the
SonicStage software will be used, and then click [Next].
continued
89
4 Click [Install SonicStage and MD Simple Burner] and then follow the
displayed instructions.
Click [Install SonicStage and MD Simple
Burner]
Read the instructions carefully.
Depending on your region, the buttons other than [Install SonicStage and MD Simple
Burner] may differ from those in the illustration above.
The installation may take 20 to 30 minutes, depending on your system environment.
Make sure to restart your computer only after the installation is completed.
Was the installation successful?
If any trouble occurs during the installation, see “Troubleshooting” (page 110).
90
Using SonicStage
Importing audio data
This section explains how to record and store audio data from an audio CD to My Library
of SonicStage on the hard disk drive of your computer. You can also assign cover art for
imported albums.
You can record or import music from other sources such as the Internet and your
computer’s hard disk. Refer to SonicStage Help for details.
Notes
• Only audio CDs with a
mark can be used with SonicStage.
• We do not guarantee normal operation in the case of the copy-controlled CDs.
Playback
control
section
[
Music Source]
Cover art
display
[CD Info]
[Settings]
1 Start up SonicStage.
Select [Start] – [All Programs]*– [SonicStage] – [SonicStage].
∗[Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition
SonicStage starts up and the main window appears.
z
You can also start SonicStage with double click
([SonicStage] icon) on the desktop.
2 Insert the audio CD that you want to record into the CD drive of your
computer.
continued
91
3 Point to [ Music Source] on the upper-left side of the screen and click
[Import a CD].
The screen switches to the “Music Source” (Importing CD) screen and all the tracks on
the audio CD are listed.
4 If necessary, click
to uncheck tracks you do not want to record.
If you unchecked a box by mistake, click it again to restore the check.
To check all boxes, click
To uncheck all boxes, click
.
.
5 If necessary, change the format and bit rate for audio CD recording.
When you click [Settings] on the right side of the screen, “CD Importing Format”
dialog box will appear. The dialog box will ask you to select the format and bit rate for
recording an audio CD.
6 Click
.
To stop recording
Click
.
To assign cover art for imported albums
Find the desired image file (jpg, gif, bmp file) using Windows Explorer and drag it to the
cover art display in the playback control section.
z
If CD information such as album title, artist name, and track names could not be obtained
automatically, click [CD Info] on the right side of the screen. When you do this, your computer must be
connected to the Internet.
92
Transferring audio data from your computer to the
MD Walkman
Audio data stored in My Library of SonicStage can be transferred to your MD Walkman an
infinite number of times.
[Transfer
]
The My Library
list
[Settings]
1 Insert a disc into the MD Walkman and connect the MD Walkman to your
computer.
Use the supplied USB cable for the MD Walkman to connect the MD Walkman to your
computer.
Do not disconnect the power source or the USB cable before the transfer has
completed.
2 Point to [Transfer ] on the upper-right side of the screen and click [Hi-MD]
or [Net MD].
The screen is switched to the transfer (Hi-MD or Net MD) screen.
3 Click the tracks you want to transfer in the My Library list on the left side of
the screen.
To transfer more than one track, hold down the [Ctrl] key while selecting the tracks.
To transfer all tracks of the album, click the album.
continued
93
4 If necessary, change the transfer mode.
As the default setting, tracks in the OpenMG (PCM/ATRAC3/ATRAC3plus) format
will be transferred in the same format and bit rate (normal transfer).
If the device connected to the computer does not support the above format, the format
and bit rate will be converted to those of the device. In some case, this process may
take time.
If you want to change the format and bit rate, click [Settings] in the center of the screen
to display “Transfer Mode Settings” dialog box.
5 Click
.
To stop transferring
Click
.
To play a disc on a Net MD device that does not support Hi-MD
If you want to play the transferred tracks on a Net MD Walkman that does not support Hi-
MD, select [Net MD] for the mode (operation mode) on the right side of the screen after
disc in Hi-MD mode for recording.
Notes
• A transfer will fail and an error message will appear in the following cases:
—When there is no enough free space on the disc.
—When the track is subject to playback restrictions.
• During the transfer, the system suspend, sleep, or hibernation function will not operate.
• Depending on the type of the text and number of characters, the text entered by SonicStage may not be
displayed on the connected MD Walkman. This is due to the limitations of the connected MD
Walkman.
z
If you are using a camera-equipped Hi-MD Walkman in Hi-MD mode, whenever you select an album
for which album art has been registered, the cover art is transferred to the Hi-MD Walkman along with
the album. Cover art is not be transferred in the case of individual tracks.
94
Transferring back audio data from the MD Walkman
to your computer
[Transfer
]
The My Library
list
List of tracks on
the MD
Transferring from the MD Walkman back to your computer
Audio data that has been transferred from your computer and stored on the MD can be
transferred back to My Library of SonicStage on your computer.
1 Insert a disc into the MD Walkman and connect the MD Walkman to your
computer.
Use the supplied USB cable for the MD Walkman to connect the MD Walkman to your
computer.
Do not disconnect the power source or the USB cable before the transfer has
completed.
2 Point to [Transfer ] on the upper-right side of the screen and click [Hi-MD]
or [Net MD].
The screen is switched to the transfer (Hi-MD or Net MD) screen.
3 In the list on the right side of the screen (Hi-MD or Net MD), click to select
the tracks you want to transfer to your computer.
continued
95
4 Click
in the middle of the screen.
To stop transferring
Click
.
To import cover art set using a camera-equipped Hi-MD Walkman
to My Library
If you are using a camera-equipped Hi-MD Walkman in Hi-MD mode, you can modify the cover art for
any group transferred from My Library, as well as register the covet art for another group. The
following two ways can be used to import the cover art to My Library.
• Insert the disc with the updated cover art, and then press the [
right side of the screen.
Auto Import] button on the bottom-
The cover art in My Library is automatically updated.
• Select the group for which you want to import the cover art by clicking it on the right side (Hi-MD
side) of the display, select [Import Cover Art] from the right-click menu, and then select the album for
which you want to add the cover art from the “Select an Album” dialog box.
Note
Tracks transferred to the MD Walkman from another computer cannot be transferred back to My
Library on your computer.
Importing tracks recorded on a Hi-MD Walkman* to your
computer
Tracks that have been recorded on a Hi-MD Walkman* can be imported to My Library of
SonicStage on your computer only once.
You can save analog-recorded tracks as WAV format files, which makes them easier to
handle during editing, etc.
∗ Only tracks recorded in Hi-MD mode
1 Insert recordable disc into the Hi-MD Walkman and connect the Hi-MD
Walkman to your computer.
2 Point to [Transfer ] on the upper-right side of the screen and click [Hi-MD].
The screen is switched to the transfer (Hi-MD) screen.
96
3 Click the tracks you want to transfer in the Hi-MD list on the right side of the
screen.
To transfer more than one track, hold down the [Ctrl] key while selecting the tracks.
To transfer all tracks of the group, click the group.
4 Click
in the middle of the screen.
The “Import” dialog box appears.
5 Click [Yes].
To stop importing
Click
.
z
When tracks recorded in analog are included on a Hi-MD, a dialog box appears confirming whether to
save those tracks in WAV format. To save the tracks as WAV format music files, select the check box
next to “Save in WAV format when importing”, click Browse button and specify a destination folder as
necessary, and click the [OK] button.
Note
Notes
• You cannot import tracks that were recorded in a Net MD mode (MD mode) to your computer, or
tracks that have been recorded on a device that does not support Hi-MD mode.
• Before importing tracks recorded on the Hi-MD Walkman to the computer, click [Settings] in the
middle of the screen to display “Transfer Mode Settings” dialog box, and then confirm the status of
the [Import settings] check box (it is checked by default) in [Advanced...]. Then do as follows:
—To import tracks to My Library while deleting them on the Hi-MD Walkman, uncheck the box.
—To import tracks to My Library while leaving the copy of them on the Hi-MD Walkman, check the
box. Tracks left on the Hi-MD Walkman are treated the same as tracks that have been automatically
transferred from the computer. For this reason, they cannot be divided or combined on the Hi-MD
Walkman.
• When you transfer tracks recorded in linearPCM on the Hi-MD Walkman to a computer for editing
(dividing or combining) in My Library, the editing may take a long time, depending on the length of
the tracks and capabilities of your computer. This is due to limitations in the MiniDisc system. If you
want to edit long tracks recorded in linearPCM, we recommend that you do the editing on the Hi-MD
Walkman first, and then transfer the edited data to a computer afterwards.
97
Writing audio data to a CD-R/CD-RW disc
You can write tracks in My Library of SonicStage to a CD-R/CD-RW disc. Analog tracks
recorded on a Hi-MD device and imported to My Library can be written to and enjoyed on
a CD-R/CD-RW. The number of times data can be written may be limited due to copyright
restrictions.
[Transfer
]
Operation Status
Display
The My Library list
The tentative list
of items to be
written to the
CD-R/CD-RW
disc
1 Point to [Transfer ] on the upper-right side of the screen, and then select the
type of CD to be created.
To create an audio CD, select [Create an Audio CD]. To create an ATRAC CD, select
[Create an ATRAC CD]. To create an MP3 CD, select [Create an MP3 CD].
ATRAC CDs can be played only on devices that support ATRAC CDs. MP3 CDs can
be played only on devices that support MP3 CDs.
2 Insert a blank CD-R/CD-RW disc into the disc drive of your computer.
Use a CD-R/CD-RW with a recording capacity of 650MB or 700MB. Data may not be
correctly written if a disc of another capacity is used.
3 Select the albums or tracks to be written to the CD-R/CD-RW disc by clicking
them in the My Library list on the left side of the screen.
By double-clicking an album, you can see a list of the tracks on the album and select
the tracks you want.
98
4 Click
in the middle of the screen.
The selected albums or tracks appear on the right side of the screen (the CD-R/CD-
RW) as a tentative list of items to be written.
5 Click
in the right of the screen.
The “Writing Settings” dialog box appears allowing you to set options for writing.
6 Click [OK].
Writing to the disc begins.
A message appears when writing has completed.
7 Click [OK].
The disc is automatically ejected, and the screen returns to the Transfer (CD Creation)
screen.
To cancel track writing
1 Click
in the Operation Status Display while tracks are being written to the disc.
Writing to the disc is canceled and a message appears.
2 Click [OK].
The disc is automatically ejected, and the screen returns to the Transfer (CD Creation) screen.
Note
Notes
• Only tracks in MP3 format can be written to an MP3 CD.
• Tracks that have been digitally recorded on a Hi-MD device and then imported to SonicStage cannot
be written to an audio CD. However, analog tracks recorded on a Hi-MD device can be written to a
CD.
99
Using SonicStage Help
SonicStage Help provides further details on how to use SonicStage. SonicStage Help
allows you to search easily for information from a list of operations, such as “Importing
Tracks” or “Transferring Tracks”, or from large list of keywords, or by typing in words that
might lead you to the appropriate explanations.
To display SonicStage Help
Click [Help] – [SonicStage Help] while SonicStage is running.
[SonicStage Help]
z
You can display SonicStage Help by selecting the following:
[Start] – [All Programs]*– [SonicStage] – [SonicStage Help].
∗ [Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition
Notes
• In SonicStage Help, “Device/Media” is the general term for the external device such as the MD
Walkman, the Network Walkman, and the CD Walkman.
• Follow the instructions of your internet provider regarding such things as recommended system
environment when using EMD services.
100
Understanding SonicStage Help
The left side frame
The right side frame
1 Double click [Overview] in the left-side frame.
2 Click [About This Help File].
The explanation will appear in the right-side frame.
3 Read the text.
Scroll the display if necessary.
Click underlined words to jump to their explanations.
Searching for a word inside an explanation
[Search]
“Type in the keyword
to find” text box
An explanations
of the selected
item
[List Topics]
The list of the words
that you searched
[Display]
1 Click [Search] to open the “Search” window.
2 Type in the words.
3 Click [List Topics].
A list of the words that were searched is displayed.
4 Click to select the desired item among those displayed.
5 Click [Display].
An explanation of the selected item is displayed.
101
Referring to SonicStage Help
Click [Contents] on the left side of the Help window to view a list of items for each
operation. Click on any items for details.
Importing audio data to the computer
To
SonicStage Help
Import audio data from the
Internet
[Importing Tracks] – [Purchasing Tracks from a Music
Service Site]
Import audio files on the
computer in SonicStage
[Importing Tracks] – [Importing Music Files]
Listening to audio data on the computer
To
SonicStage Help
Listen to audio data from the
CD drive or My Library
[Music Playback] – [Playing Back an Audio CD] or
[Playing Back a Track in My Library]
Listen to audio data on the MD [Music Playback] – [Playing Back a Track on a Device/
Walkman connected to the
computer
Media]
Managing and editing imported tracks
To
SonicStage Help
Change information related to [Changing SonicStage Settings] – [Changing Settings
CD information downloading
for the CD Drive]
Edit an album
Delete the tracks
[Managing Tracks and Albums] – [Creating/Editing
Albums]
Change the destination directly [Changing SonicStage Settings] – [Changing the
for track storage Location for Saving Imported Files]
102
Backing up audio data
We recommend that you back up your music data as a precaution against hard disk crashes
or computer replacement.
To
SonicStage Help
Back up audio data in My
Library
[Backing Up My Library] – [Backing Up Data to a
Disk]
Look up about SonicStage
backup
[Backing Up My Library] – [FAQ-About SonicStage
Backup Tool]
Troubleshooting
To
SonicStage Help
Look up troubleshooting
procedure
[Additional Information] – [Troubleshooting]
When you want to know
To
SonicStage Help
Look up unknown words
[Additional Information] – [Glossary]
Look up the kinds of audio data [Overview] – [Content Handled Within SonicStage]
that can be managed by
SonicStage
Look up the kinds of functions [Overview] – [Features]
that can be used with
SonicStage
Look up changes since an
earlier version
[For Users of Earlier Versions of SonicStage] –
[Differences from Earlier Versions]
103
Using MD Simple Burner
Before using MD Simple Burner
MD Simple Burner allows you to record music tracks from an audio CD in the CD drive of
your computer to the MD Walkman.
There are two ways to record from an audio CD.
You can use MD Walkman operations to record an entire CD or only the first track
without launching MD Simple Burner.
You can launch MD Simple Burner to record using computer operations. Record an entire
CD or selected tracks.
Notes
• You cannot record in simple mode while the MD Simple Burner in standard mode or OpenMG
software (SonicStage, OpenMG Jukebox, etc.) is active.
• Only audio CDs with a
mark can be used with MD Simple Burner.
• We do not guarantee normal operation in the case of the copy-controlled CDs.
104
Recording using MD Walkman operations (Simple mode)
1 Insert a recordable disc into the MD Walkman and then connect the MD
Walkman to the computer.
Do not disconnect the power source or the USB cable before the transfer has
completed.
2 Insert the audio CD that you want to record into the CD drive of your
computer.
The CDDB registration window appears when you use the CDDB for the first time.
You need to connect the computer to the Internet in order to use the CDDB.
3 Press the jog dial (N/ENT) while pressing REC(+N)/T MARK on the MD
Walkman.
The recording starts.
All tracks on the CD are recorded as a new group.
To stop recording
Click
on the computer display.
While the first track is being recorded, you can use x (stop) button to stop on the MD
Walkman.
Setting the recording mode
Before starting recording, right-click the
then select in [recording mode].
MD Simple Burner icon in the task tray, and
• [Net MD]: [LP2] or [LP4]
• [Hi-MD]: [PCM], [Hi-SP], [Hi-LP], or [48kbps]
Recording first track only
Before starting recording, right-click the
MD Simple Burner icon in the task tray, and
then select [Recording settings] – [Record 1st Track Only].
Setting when the CDDB has more than one item of information
Right-click the
MD Simple Burner icon in the task tray, and then select the setting by
clicking [CDDB(r)] – [Multiple Matches].
— [User Selection]: A selection window is displayed
— [No Resolve]: No CD information is downloaded
— [First Choice]: The first item is downloaded
105
Recording by computer operations (Standard mode)
To start MD Simple Burner, click [Start] – [All Programs]* – [MD Simple Burner] – [MD
Simple Burner].
∗ [Programs] in the case of Windows 2000 Professional/Windows Millennium Edition/Windows 98
Second Edition
z
There are other ways to start up MD Simple Burner as follows:
• Double-click the
Standard Mode].
• Double-click the
MD Simple Burner icon in the task tray, or right-click and select [Show
MD Simple Burner shortcut icon on the desktop.
The window for recording all tracks on the CD
[REC/STOP]
To start recording all tracks on the CD as
a new group, click here.
To stop recording, click [STOP].
Total time of the
selected tracks of CD
CD icon
Disc name (MD)
MD icon
Remaining
recording time of
the inserted MD
Album name (CD)
[Open]
Artist name (CD)
To open the display
as shown on page
107, click here.
Recording mode drop down menu
Net MD: LP2/LP4
Hi-MD: PCM/Hi-SP/Hi-LP/48kbps
106
The window for recording selected tracks from an audio CD
[CONFIG]
Track information
(CD)
Click here to do the following:
-Set the CD-ROM drive
-View version information for MD Simple Burner
-Confirm CD information registered in the CDDB
Total time of the
selected tracks of CD
Track information (MD)
Artist name
You can change the
track name and track
number
[REC/
STOP]
Disc name
(MD)
Album Title
[Get CD Info]
[New Group]
Information of an audio CD
(album name, track title,
etc.) will be reflected in the
track list.
Recording mode
drop down menu
[Close]
To close the display as shown
CD operating section
Use these controls to confirm the tracks on audio CD to
be recorded
[Erase]
[All Erase]
Remaining time of the inserted MD
To deselect all tracks, click here.
To select all tracks, click here.
Check boxes
Check the box of the tracks
that you want to record
107
Other information
Uninstalling SonicStage/MD Simple Burner
To uninstall SonicStage/MD Simple Burner, follow the procedures below.
1 Click [Start]–[Control Panel]*.
∗ [Settings]–[Control Panel] in the case of Windows 2000 Professional/Windows Millennium
Edition/Windows 98 Second Edition
2 Double-click [Add/Remove Programs].
3 Click [SonicStage 3.1.xx] or [MD Simple Burner 2.0.xx] in the “Currently
Installed Programs” list, and then click [Change and Remove]*.
Follow the displayed instruction and restart your computer. The uninstallation is
completed when the computer has restarted.
∗ [Change/Remove] in the case of Windows 2000 Professional, [Add/Remove] in the case of
Windows Millennium Edition/Windows 98 Second Edition
Note
When you install SonicStage Ver. 3.1/MD Simple Burner Ver. 2.0, OpenMG Secure Module 4.1 is
installed at the same time. Do not delete OpenMG Secure Module 4.1 since it may be used by other
software.
108
On copyright protection
The OpenMG technology allows you to enjoy digital music, while maintaining the
copyrights of its holders.
Restrictions on audio content
High-quality digital audio content is widely available through music distribution services
on the Internet. To protect the copyrights of its holders from unauthorized distribution,
some audio content is distributed with certain restrictions on recording and playback. For
example, the playback period or playback count for the data may be limited.
109
Troubleshooting
Please refer to the following steps if you encounter a problem while using SonicStage/MD
Simple Burner.
2 Check the symptoms in SonicStage Help when you use SonicStage.
3 If the problem cannot be solved after checking the above references, check the
following table and then consult your nearest Sony dealer.
Computer
• Manufacturer:
• Model:
• Type: Desktop type / Laptop type
Name of operating system:
RAM capacity:
Hard disk drive (containing SonicStage/MD Simple Burner and audio data)
• Capacity of the drive:
• Free space:
Version of the software
• SonicStage Ver. 3.11)
• MD Simple Burner Ver. 2.02)
Error Message (if one appear):
If an externally connected CD-ROM drive is used
• Manufacturer:
• Model:
• Type: CD-ROM / CD-R/RW / DVD-ROM / Other (
)
• Type of connection to the computer: PC card / USB / IEEE1394 / Other (
)
If another device with USB connection is used
• Name of the device (or devices):
1)
To check the SonicStage software version, go to [Help] – [About SonicStage] in the SonicStage
window.
To check the MD Simple Burner software version, go to [CONFIG] – [Version] in the MD Simple
Burner window.
2)
110
The software cannot be installed onto your computer
Problem
Cause/Remedy
The installation was not
successful.
You are using an OS that does not support this
software.
All Windows applications are not closed.
tIf you start the installation while other programs are
running, a malfunction may occur. This is especially
true for programs that require large amounts of
system resources, such as virus-check software.
There is not enough hard disk space on your hard disk.
tYou need 200MB or more free space on your hard
disk.
The installation appears to have Check for the appearance of an error message beneath
stopped before it has
completed.
the installation window.
tPress the [Tab] key while holding down the [Alt]
key. If an error message has appeared, press the
[Enter] key. The installation will resume. If there is
no message, the installation is still in progress. Wait
a little while longer.
The progress bar on the display The installation is progressing normally.
is not moving. The access lamp
has not lit for a few minutes.
tPlease wait.
The installation may take 30 minutes or more,
depending on your CD drive or system environment.
111
Using a MD Walkman connected to the computer
Problem
Cause/Remedy
Your computer does not
recognize the MD Walkman.
The MD Walkman is not firmly connected with the
supplied USB cable to the computer.
tReconnect the MD Walkman to the computer firmly.
tRemove and reconnect the MD Walkman. If the
computer still does not recognize the MD Walkman,
disconnect the cable, restart the computer, and then
make the connection again.
A disc is not inserted in the MD Walkman.
tCheck if a disc is inserted in the MD Walkman.
The Net MD driver is not installed.
tInstall the SonicStage/MD Simple Burner software
using the supplied CD-ROM.
The software installation failed.
tDisconnect the connected device and install the
software again using the supplied CD-ROM.
The supplied USB cable is disconnected.
tConnect the supplied USB cable firmly.
The connections are made through a USB hub.
tOperations are not guaranteed for USB-hub
connections. Connect the MD Walkman directly to
the USB connector on the computer.
Even though the supplied USB It takes time to recognize SonicStage.
cable is used to connect the
MD Walkman to the computer,
the display on the MD
Walkman does not indicate it is
connected.
tPlease wait.
The other application software is running.
tReconnect the supplied USB cable after a while. If
the computer still does not recognize the MD
Walkman, disconnect the MD Walkman, restart the
computer, and connect the USB cable again.
Even though your computer
recognize the MD Walkman, it
does not operate normally.
The supplied USB cable is disconnected.
tConnect the supplied USB cable firmly.
The connections are made through a USB hub.
tOperations are not guaranteed for USB-hub
connections. Connect the MD Walkman directly to
the USB connector on the computer.
112
Index
A
G
A-B Repeat 42
Accessories
Group
erasing 52
moving 51
recording 37
releasing 50
setting 49
optional 68
supplied 12
ATRAC3plus 81
AVLS 56
Group skip 26
H
B
Battery life 20
BEEP 56
Hard disk
free space 88
Hi-MD 81
Hi-MD WAV Importer 11
Bookmark 41
C
CD drive 88
I
CD-R/RW drive 88
CD-ROM 89
Character palette 47
Charging 17
Clamp filter 13
Cleaning 66
Combining tracks 54
Computer 60
Connecting 105
Importing 91
Initial Search 43
Installing 88
L
LinearPCM 81
M
MD Simple Burner 104
Menu list 28
Menu Mode 56
Move
analog 34
computer 61
digital 21
groups 51
tracks 50
when charging 17
Contrast 58
My Library 91
Copyright protection 109
D
O
OpenMG Secure Module 4.1 108
Operation mode 22
Data storage 62
Disc memory 57
Disc Mode 58
Display language 59
P
Play mode
Main Play Mode 40
Repeat Play 42
Sub Play Mode 42
E
Q
EMD service 88
Erasing 52
Quick mode 57
F
File list 63
Format 55
113
R
W
WAV 97
Recording
analog 34
digital 21
from microphone 32
recording mode 34
Synchro-recording 38
time 82
Windows Media Player 88
Recording mode 105
Recording mode (Bit rate) 92
Windows XP Home Edition 88
Windows XP Media Center Edition 88
Windows XP Media Center Edition 2004 88
Windows XP Media Center Edition 2005 88
Windows XP Professional 88
S
Simple mode 105
SonicStage 91
SonicStage Help 100
Start (software)
MD Simple Burner 106
SonicStage 91
Storage space 64
System environment 88
System limitations 88
T
Title 46
Track mark
erase 54
Track search 43
Transferring
to the MD Walkman 93
to your computer 95
U
Uninstalling 108
USB bus power 60
USB port 88
114
This warranty is valid only in Canada.
|