Seagate Momentus ST9160414AS User Manual

Product Manual

Momentus 7200 FDE.1 SATA

ST9320424AS

ST9250424AS

ST9160414AS

ST9120414AS

ST9320424ASG

ST9250424ASG

ST9160414ASG

ST9120414ASG

ST980414ASG

100515958

Rev. A

July 2008

Contents

1.0

2.0

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1

1.2

System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

About Momentus 7200 FDE.1 SATA disc drive s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2.1

Drive state upon shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1

2.2

Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2.1

LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Power-management mode s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2

2.10

Environmental specification s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3

Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Altitud e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3

Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Vibratio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4

2.11

2.12

2.13

Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.13.1

Free Fall Protection feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.14

Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.14.1

2.14.2

2.14.3

Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.15

2.16

Environmental protectio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 0

2.15.1

2.15.2

European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 20

China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 20

Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.0

Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Drive integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.5.1

3.5.2

Drive installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Consumer usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.6

Security Erase--ATA security commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.6.1

3.6.2

Secure Erase procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Drive State after Secure Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.0

Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.1

4.2

Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Serial ATA device plug connector pin definition s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 7

ATA Security policy exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DriveTrust Mode support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Full Disc Encryption suppor t . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1

Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Identify Device command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.0

6.0

Compatibility summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.1

5.2

Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

System Compatibility using WIndows XP SP2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.2.1

5.2.2

BIOS versions tested in ATA Security mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

DriveTrust compatibility verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

5.3

5.4

Operating system versions tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Compatibility test configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

List of Figures

Figure 5.

Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Mounting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Momentus 7200 FDE.1 SATA drive label example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

iii

1.0

Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate

Momentus^®7200 FDE.1 SATA model drives:

ST9320424AS

ST9250424AS

ST9160414AS

ST9120414AS

ST9320424ASG (includes Free Fall Sensor)

ST9250424ASG (includes Free Fall Sensor)

ST9160414ASG (includes Free Fall Sensor)

ST9120414ASG (includes Free Fall Sensor)

ST980414ASG (includes Free Fall Sensor)

These drives provide the following key features:

• DriveTrust technology including:

• Hardware-based Full Disc Encryption (FDE)

• DriveTrust security interface and ATA security interface

• Integrates with standard security software packages to provide features such as: Pre-boot authentica-

tion and initialization using the drive’s secure partition and DriveTrust API

• Encryption key escrow.

• 7,200-RPM spindle speed

• 16-Mbyte buffer.

• Free Fall Protection (on ST9320424ASG, ST9250424ASG, ST9160414ASG,

ST9120414ASG and ST980414ASG models only)

• Quiet operation. Fluid Dynamic Bearing (FDB) motor.

• High instantaneous (burst) data transfer rates (up to 3 Gbits/sec).

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Native Command Queuing (NCQ) with command ordering.

• Full-track multiple-sector transfer capability without local processor intervention.

• 1,000 Gs nonoperating shock and 350 Gs operating shock.

• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

1.1

System requirements

The following hardware and software is required to use these drives.

Host system requirements:

• Windows XP with Service Pack 2 (or later) when utilizing the Windows DriveTrust API.

• System/BIOS that supports ATA Security commands.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

1.2

About Momentus 7200 FDE.1 SATA disc drives

Momentus^®7200 FDE.1 SATA drives contain DriveTrust technology providing Full Disc Encryption (FDE)

using proven Advanced Encryption Standard (AES) data encryption and decryption.

You can elect to use Momentus 7200 FDE.1 SATA drives in one of two different security modes:

1. The ATA Security mode

To operate in ATA Security mode, you only need a host system and operating system that supports the

existing ATA Security Command Set. The drive is shipped to operating in this mode, ready to use.

2. The DriveTrust Security mode

To enable a robust enterprise-level security and management policy, you may elect to operate in

DriveTrust Security mode. To do so, you will need to use a third-party security application to manage the

DriveTrust features. Please contact your system or software provider for more details.

Refer to the table below to determine which mode is best for your particular solution.

Table 1:

Security feature matrix

ATA Security mode

FDE drive with ATA

DriveTrust mode

Non-FDE drive

without ATA Security

enabled

FDE drive operating in

DriveTrust mode via

third-party software

Non-FDE drive with

Feature

ATA Security enabled Security enabled

Password required to unlock

Full Disk Encryption

At speed encryption

Passwords stored securely

Quick erase

Yes

Preboot authentication

Master/User passwords

FDE drive feature list

• Automatically encrypts (and decrypts) all data on the drive

• Operations are performed with no measurable performance loss

• All user data is encrypted on write operations and decrypted on read operations

FDE benefits

• Drive-level protection of data

• Drives that are stolen, taken out of service, or re-purposed remain fully protected

• Near instantaneous disposal and re-purposing of the drive (ensures that data from previous user is not

accessible by the new drive owner)

• Able to be deployed within a trusted computing environment

The drive encrypts every write operation and decrypts every read operation without user intervention. The

encryption and decryption is done on the drive itself, so there is a near-zero performance impact when the

drive writes and reads data. The performance-optimized encryption and decryption engine performs at the

SATA interface speed.

The purpose of full disc encryption on the drive is to protect the data stored on the drive in the event that the

host system is lost or stolen. This data at rest protection assures the system owner that if their system is lost or

stolen, their data will not be accessible without the correct credentials.

Note. The system reauthenticates the user on powerup and when awakening from sleep mode. It is not

necessary to power down to ensure that the system reauthenticates the user.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Having the encryption/decryption on the drive also provides the highest level of security for data because all

data, including the boot sector bytes, operating system, temp and even the swap files are encrypted at the

drive level.

1.2.1

Drive state upon shipment

Upon shipment from the Seagate factory, the ATA Security Interface is enabled and functioning. This is

referred to as operating in ATA Security mode. The following is the detailed state of the drive upon shipment.

• Full Disc Encryption is active and functioning. All user data is encrypted on write and decrypted on read.

• The user interface to the drive is active and all read and write commands are allowed.

• The ATA user password is null (no value).

• The ATA master password is set to the Security ID (SID).

• ATA Security is set to the unlocked state. No password is required to access the drive.

Momentus 7200 FDE.1 SATA drives may be integrated into the computer system in the same way you would

integrate a non-FDE Momentus drive.

The encryption key is enabled and operational when the drive leaves the Seagate factory. No user id is

required to access the drive, so the data on the drive is accessible to anyone possessing the drive.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.0

Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power.

2.1

Specification summary table

The specifications listed in this table are for quick reference. For details on specification measurement or defi-

nition, see the appropriate section of this manual.

Table 2:

Drive specifications

ST9320424AS

ST9250424AS

ST9160414AS

ST9120414AS

Drive specification

ST9320424ASG ST9250424ASG

ST9160414ASG

ST9120414ASG

ST980414ASG

Formatted Gbytes (512 bytes/sector)*

Guaranteed sectors

320

250

160

120

625,142,448

488,397,168

312,581,808

234,441,648

156,301,488

Bytes per sector

512

Physical read/write heads

Discs

Cache (Mbytes)

Recording density in BPI (bits/inch max)

Track density TPI (tracks/inch max)

1,334k

190k

253

7.200

1.1

Areal density (Gbits/inch max)

Spindle speed (RPM)

Internal transfer rate (Gbits/sec max)

I/O data transfer rate (Gbits/sec max)

ATA data-transfer modes supported

3.0

SATA 1.5/3.0, Serial ATA Revision 2.6

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–6

Height (max)

9.5 +/- 0.2 mm (0.374 +/- .0078 inches)

69.85 +/- .249 mm (2.75 +/- .0098 inches)

100.33 +/- 0.25 mm (3.95 +/- .010 inches)

Width (max)

Length (max)

Weight (typical)

110 grams (0.238 lb)

105 grams (0.227 lb)

Average latency (msec)

Power-on to ready (sec typical)

Standby to ready (sec typical)

Track-to-track seek time, read (msec typical)

Average seek, read (msec typical)

Average seek, write (msec typical)

Startup current, +5V (max)

Seek power (typical)

4.17

4.0

3.0

1.0

11.0

13.0

1.0 amps

2.3 watts

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 2:

Drive specifications

ST9320424AS

ST9250424AS

ST9160414AS

ST9120414AS

Drive specification

ST9320424ASG ST9250424ASG

ST9160414ASG

ST9120414ASG

ST980414ASG

Read power (typical)

2.1 watts

Write power (typical)

2.3 watts

Idle mode, low power (typical)

Standby mode

0.75 watts

0.21 watts (typical)***

+5V ± 5%

Sleep mode

Voltage tolerance (including noise)

Ambient temperature

0° to 60°C (operating), –40° to 70°C (nonoperating)

Temperature gradient (°C per hour max)

20°C (operating)

35°C (nonoperating)

Relative humidity

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

Wet bulb temperature (max)

30% per hour max

30°C (operating)

40°C (nonoperating)

Altitude, operating

–60.96 m to 3,048 m (–200 ft to 10,000+ ft)

–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)

Altitude, nonoperating

(meters below mean sea level, max)

Shock, operating

350

(Gs max at 2 msec)

Shock, nonoperating

(Gs max at 2 msec)

800

Shock, nonoperating

(Gs max at 1 msec)

1,000

600

Shock, nonoperating

(Gs max at 0.5 msec)

Vibration, operating

Vibration, nonoperating

Drive acoustics, sound power (bels)

Idle**

1.0 G (0 to peak, 5–500 Hz)

5 Gs (0 to peak, 5–500 Hz)

2.3 (typical)

2.5 (max)

Performance seek

2.6 (typical)

2.7 (max)

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Load/Unload (U/UL) cycles

1 per 10 bits read

0.48%

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

50,000 hard power on/off cycles

32°C, 80% relative humidity

5°C, 80% relative humidity

5°C, 10% relative humidity

55°C, 16% relative humidity

600,000 software-controlled power on/off cycles

50,000 hard power on/off cycles

Warranty

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the follow-

ing web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to provide

the drive serial number, model number (or part number) and country of purchase. The

system will display the warranty information for your drive.

Supports Hotplug operation per Serial ATA

Revision 2.5 specification

Yes (requires COMPRESET from host after a hotplug event)

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby

modes will not contribute to battery power consumption.

2.2

Formatted capacity

Model

Formatted capacity*

320 Gbytes

Guaranteed sectors

625,142,448

Bytes per sector

ST9320424AS and ST9320424ASG

ST9250424AS and ST9250424ASG

ST9160414AS and ST9160414ASG

ST9120414AS and ST9120414ASG

ST980414ASG

512

250 Gbytes

488,397,168

160 Gbytes

312,581,808

120 Gbytes

234,441,648

80 Gbytes

156,301,488

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

2.2.1

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

See Section 4.2.5, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-

bit addressing support of drives with capacities over 137 Gbytes.

2.3

Default logical geometry

Cylinders

Read/write heads

Sectors per track

16,383

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.4

Physical organization

Drive model

Read/write heads

Number of discs

ST9320424AS and ST9320424ASG

ST9250424AS and ST9250424ASG

ST9160414AS and ST9160414ASG

ST9120414AS and ST9120414ASG

ST980414ASG

2.5

Recording and interface technology

Interface

Serial ATA (SATA)

Perpendicular

1,334k

Recording method

Recording density BPI (bits/inch max)

Track density TPI (tracks/inch max)

190k

253

Areal density (Gbits/inch max)

Spindle speed (RPM) ( 0.2%)

Maximum Internal transfer rate (Gbits/sec)

I/O data-transfer rate (Gbits/sec max)

Interleave

7,200

1.1

3.0

1:1

Cache buffer

16 Mbytes (16,384 kbytes)

2.6

Physical characteristics

Drive specification

Height

(mm)

9.5 +/-0.2

(inches)

0.374 +/-0.0078

Width

(mm)

(inches)

69.85 +/-0.249

2.75 +/-0.0098

Length

(mm)

(inches)

100.33 +/-0.25

3.95 +/-0.010

Typical weight

ST9320424AS

110 grams

ST9320424ASG

ST9250424AS

ST9250424ASG

0.238 pounds

ST9160414AS

ST9160414ASG

ST9120414AS

ST9120414ASG

ST980414ASG

105 grams

0.227 pounds

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.7

Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using

drive diagnostics. The specifications in the table below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between

random tracks, less overhead.

Typical seek times (msec)

Track-to-track

Read

1.5

Average

11.0

22.0

4.17

Full-stroke

Average latency

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical

seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted

values. However, due to the manner in which these drives are formatted, benchmark tests that

include command overhead or measure logical seeks may produce results that vary from these

specifications.

2.8

Start/stop times

Max @ 25°C

Time to ready

Typical

4.0

Power-on to Ready (sec)

Standby to Ready (sec)

8.0

3.0

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.9

Power specifications

The drive receives DC power (+5V) through a native SATA power connector.

2.9.1 Power consumption

Power requirements for the drives are listed in table 3. Typical power measurements are based on an average

of drives tested, under nominal conditions, at 25°C ambient temperature.

• Spinup power

Spinup power is measured fromthe time ofpower-onto thetimethat the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does

not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on

three random seek operations every 100 msecs. This mode is not typical.

• Read/write power and current

Read/write power is measured with the heads on track, based on three 63 sector read or write operations

every 100 msecs.

• Idle mode power

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/

write electronics are in power-down model

Table 3:

DC power

Power dissipation

Spinup (max)

Seek

+5V input average (25° C)

1.0 amps

2.3 watts

Read

2.1 watts

Write

2.3 watts

Idle, performance*

Idle, active*

Idle, low power mode*

Standby

1.4 watts

1.0 watts

0.75 watts

0.21 watts

Sleep

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.9.1.1

Typical current profile

Figure 1. Typical +5V only startup and operation current profile

2.9.2

Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on

the +5 volt line.

Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write

current.

2.9.3

Voltage tolerance

Voltage tolerance (including noise):

5V 5%

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.9.4

Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems,

you can control power management through the system setup program. The drive features the following

power-management modes:

Table 4:

Power management modes

Power modes

Active (operating)

Idle, performance

Idle, active

Heads

Spindle

Rotating

Stopped

Buffer

Tracking

Floating

Parked

Full power

Self refresh—low power

Idle, low power

Standby

Sleep

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc

access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the

standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a

specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby

mode, the drive buffer is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest.

The drive accepts all commands and returns to Active mode any time disc access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer

is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep

mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep

mode and enters Standby mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and

begins counting down from its specified delay times to zero. If the standby timer reaches zero before any

drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the

drive accepts all commands and returns to Active mode when disc access is necessary.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.10

Environmental specifications

Ambient temperature

2.10.1

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.

Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.

Operating

0° to 60°C (32° to 140°F)

Nonoperating

–40° to 70°C (–40° to 158°F)

2.10.2

Temperature gradient

Operating

20°C per hour (68°F per hour max), without condensation

35°C per hour (95°F per hour max), without condensation

Nonoperating

2.10.3

Humidity

Relative humidity

2.10.3.1

Operating

5% to 95% noncondensing (30% per hour max)

Nonoperating

2.10.3.2

Wet bulb temperature

Operating

37.7°C (99.8°F max)

40°C (104°F max)

Nonoperating

2.10.4

Altitude

Operating

Nonoperating

–60.96 m to 3,048 m (–200 ft to 10,000+ ft)

–304.8 m to 12,192 m (–1,000 ft to 40,000+ ft)

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.10.5

Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive

mounting screws. Shock may be applied in the X, Y or Z axis.

Note. Additional shock protection is provided by the Free Fall Protection feature on ST9320424ASG,

ST9250424ASG, ST9160414ASG, ST9120414ASG, and ST980414ASG models. See Section

2.13.1 for additional information about this feature.

2.10.5.1

Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum

operating shock of 350 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more

than two times per second.

2.10.5.2

Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse

of 2 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 1,000 Gs based on a nonrepetitive half-sine shock

pulse of 1 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 600 Gs based on a nonrepetitive half-sine shock pulse

of 0.5 msec duration.

2.10.6

Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the

drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.10.6.1

Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards speci-

fied in this document are specified below.

5–500 Hz

1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.

2.10.6.2

Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degrada-

tion in performance when subsequently put into operation are specified below.

5–500 Hz

5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.11

Acoustics

Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is

conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted

sound power levels for steady state, idle, and active seek modes of operation.

Idle*

Performance seek

2.3 bels (typ)

2.5 bels (max)

2.6 bels (typ)

2.7 bels (max)

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Test for Prominent Discrete Tones (PDTs)

Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this pro-

cess is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to

discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone

ratios according to Annex D of the ECMA-74 standards.

*Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies.

2.12

Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in

performance when subjected to the radio frequency (RF) environments defined in the following table:

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Performance

level

Reference

standard

Test

Description

Electrostatic discharge

Radiated RF immunity

EN 61000-4-2: 95

Contact, HCP, VCP: 4 kV; Air: 8 kV

80 to 2,000 MHz, 10 V/m,

80% AM with 1 kHz sine

EN 61000-4-3: 96

ENV 50204: 95

900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz

Electrical fast transient

Surge immunity

1 kV on AC mains, 0.5 kV on external I/O

1 kV differential, 2 kV common, AC mains

EN 61000-4-4: 95

EN 61000-4-5: 95

EN 61000-4-6: 97

Conducted RF immunity

150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz

sine

Power Frequency H-field

immunity

1 A/m, 50Hz/60Hz, 3 axes

EN 61000-4-8: 97

EN 61000-4-11: 94

Voltage dips, interrupts

30% Reduction for 25 cycles

>95% Reduction for 250 cycles

>95%, 0.5 cycles

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.13

Reliability

Measurement type

Specification

Nonrecoverable read errors

1 per 10 bits read, max.

Annualized Failure Rate (AFR)

Load/Unload (U/UL)

0.48%

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

50,000 hard power on/off cycles

32°C, 80% relative humidity

5°C, 80% relative humidity

5°C, 10% relative humidity

55°C, 16% relative humidity

600,000 software-controlled power on/off cycles

50,000 hard power on/off cycles

Warranty

5 years on distribution units.

Important: When returning a drive for warranty support, if possible, you should

provide the valid ATA Master password, or return the drive in the Security Erased

state with the User Data Area accessible.

If these recommendations are not followed, Seagate cannot access the drive to

perform failure analysis to verify your warranty claim.

To determine the warranty for a specific drive, use a web browser to access the

following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

vide the drive serial number, model number (or part number) and country of pur-

chase. The system will display the warranty information for your drive.

2.13.1

Free Fall Protection feature

The Free Fall Protection feature provides enhanced data protection against shock events that may occur while

the drive is operating. This feature is designed to decrease the likelihood of data loss by detecting a free fall

event and unloading the actuator before a shock takes place in falls of >8 inches (nominal). The drive uses a

0G sensor mounted on the printed circuit board assembly (PCBA) to sense this event.

To enable the Free Fall Protection feature on ST9320424ASG, ST9250424ASG, ST9160414ASG,

ST9120414ASG, and ST980414ASG models, use Set Features command 41h. To disable this feature, use

Set Features command C1h.

Information about Free Fall Events that have occurred is available through SMART Attribute FEh.

Note. The Free Fall Protection feature is provided only on ST9320424ASG, ST9250424ASG,

ST9160414ASG, ST9120414ASG, and ST980414ASG models.

2.14

Agency certification

Safety certification

2.14.1

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections

of IEC950 and EN 60950 as tested by TUV North America.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.14.2

Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-

tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and

the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous

paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply

with the directives when used in the test systems, we cannot guarantee that all systems will comply with the

directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O

cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators

should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-

graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic

Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information

and Communication Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-

ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-

nized lab.

• Certificate number: STX - Momentus 72003 (B)

• Trade name or applicant: Seagate Technology LLC

• Manufacturing date: April 23, 2008

• Manufacturer/nationality: USA and China

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548

1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-

cation Authority (ACA).

2.14.3

FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached

as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-

keted to the customer. As a subassembly, no Federal Communications Commission verification or certification

of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total

assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B

computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is

likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not

installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installa-

tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television, which can be determined by turning the equipment on and off,

you are encouraged to try one or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-

gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:

How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-

intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-

ber 004-000-00345-4.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

2.15

Environmental protection

Seagate designs its products to meet environmental protection requirements worldwide, including regulations

restricting certain chemical substances.

2.15.1

European Union Restriction of Hazardous Substances (RoHS)

Seagate designs its products to meet environmental protection requirements worldwide, including regulations

restricting certain chemical substances. A new law, the European Union Restriction of Hazardous Substances

(RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexava-

lent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured with

components and materials that comply with the RoHS Directive.

2.15.2

China Restriction of Hazardous Substances (RoHS) Directive

This product has an Environmental Protection Use Period (EPUP) of 20 years. The following

table contains information mandated by China's "Marking Requirements for Control of Pollution

Caused by Electronic Information Products" Standard.

"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower

than the threshold defined by the China RoHS MCV Standard.

“O”

RoHS MCV

"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over

the threshold defined by the China RoHS MCV Standard.

“X”

RoHS MCV

2.16

Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to

light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM

B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro-

sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil-

ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,

chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components

should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-

nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any

electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

Momentus^®7200 FDE.1 SATA drives may be connected to any computer system that supports a standard

SATA interface.

You can elect to use Momentus 7200 FDE.1 SATA drives in one of two different security modes:

1. The ATA Security mode

To operate in ATA Security mode, you only need a host system and operating system that supports the

existing ATA Security Command Set. The drive is shipped to operating in this mode, ready to use.

2. The DriveTrust Security mode

To enable a robust enterprise-level security and management policy, you may elect to operate in

DriveTrust Security mode. To do so, you will need to use a third-party security application to manage the

DriveTrust features. Please contact your system or software provider for more details.

Refer to Table 1 on page 2 to determine which mode is best for your particular solution.

Note. As with any disc drive, Seagate highly encourages consumers to consistently back up their data as

well as the security pre-boot password, user name, and domain name on another storage device.

Seagate is not responsible for lost or stolen authentication data such as passwords, user names,

domain names, or any authentication data perceived to be inoperative, and as a consequence of

lost or stolen passwords, user names, or domain names, Seagate cannot be held liable for data

that cannot be retrieved from the drive due to inability to authenticate the user to the drive as

required by the security pre-boot software.

3.1

Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-

charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s

exposure to ESD.

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire

installation procedure.

• Handle the drive only by its edges or frame.

• The drive is fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until you mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are

used to seal out dirt and contamination.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

• Do not obstruct the breather hole located on the top cover of the drive. Refer to Figure 4 for the exact location

of this hole.

3.2

Configuring the drive

Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host

adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point

relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the

two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are

Device 0 (master) devices.

Serial ATA drives are designed for easy installation with no jumpers, terminators, or other settings. It is not nec-

essary to set any jumpers on this drive for proper operation. The jumper block adjacent to the signal connector

is for factory use only.

3.0 Gbits per second operation

Limit data transfer rate to

1.5 Gbits per second

Jumper block

SATA interface connector

Figure 2. Serial ATA connectors

SATA power connector

3.3

Serial ATA cables and connectors

The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec-

tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See T a ble 5

for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.

For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive

and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind

mateable.

For installations which require cables, you can connect the drive as illustrated in Figure 3.

SATA interface connector

Power connector

SATA interface cable

Power cable

Figure 3. Attaching SATA cabling

Each cable is keyed to ensure correct orientation.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

3.4

Drive mounting

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting

holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mount-

ing the drive:

• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

• Use only M3 UNC mounting screws.

• Do not overtighten the mounting screws. Maximum torque: 4.0 inch-lb (0.4519 N-m).

• Four (4) threads (0.080 inches, 2.032 mm) minimum screw engagement recommended.

• Avoid excessive drive distortion when mounting.

Measurements shown in Figure 4 are in inches.

3.95 +/- .010

Breather Hole

Do not cover

or seal.

Recommended

case temperature

measurement

location

Figure 4. Mounting dimensions

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

3.5

Drive integration

Momentus 7200 FDE.1 SATA drives may be installed in the target computer system in exactly the same way as

a non-FDE Momentus drive.

Figure 5. Momentus 7200 FDE.1 SATA drive label example

To install the drive in the system:

1. Remove the drive from the packaging material.

2. Install the drive in the computer system.

3. Load any desired images and operating system to the drive.

4. Install other components and options.

5. Set the original Master Password to a new value (see Section 1.2.1 for information about setting the SID)

utilizing System/BIOS or third party software (optional).

No password is required to change the Master password when the drive is in the unlocked state.

The drive remains in the unlocked state until a User password is set.

After the installation procedure is complete, the computer is ready to be shipped to the customer.

Note. The manufacturer of the computer system (system integrator) does not have to enter any password.

The installation procedure for the Momentus 7200 FDE.1 SATA is exactly the same as the Momentus

7200.3 SATA.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

3.5.1

Drive installation

Upon receipt by the consumer, the drive’s user interface is identical to a Momentus 7200.3 drive. The normal

ATA security commands are functioning and available for initialization of the password as follows:

Per normal ATA Security Commands specifications, the drive is unlocked and all ATA security commands and

all normal ATA commands may be issued.

1. Consumer accesses the computer manufacturer’s BIOS set-up screen.

2. Consumer selects option to set User Password.

After setting the User password, the drive is now under access control (locked) and will require a password

for future accesses.

3. Optional: Consumer selects the option to set the Master password from the BIOS choices.

4. Consumer exits the BIOS settings menu and continues with the boot process.

5. The BIOS enters the Security Freeze Command (F5) prior to exiting the boot sequence.

3.5.2

Consumer usage

After initialization, the consumer will just need to enter their User password each time the computer is booted

according to the following description:

1. The computer system is turned on or the hardware is reset.

2. The drive reports to the BIOS that it is in the locked state per standard ATA Security Command reporting.

3. The BIOS queries the user for the password.

4. The BIOS supplies the password to the drive using the Security Unlock Command (F2).

5. The drive is unlocked and the BIOS may continue the booting process.

6. The BIOS enters the Security Freeze Lock Command (F5) prior to exiting the boot sequence.

Note. To ensure that the system reauthenticates the user, turn the laptop power off (shut down) rather

than putting it in sleep mode. The system will authenticate the user at powerup.

3.6

Security Erase--ATA security commands

The Momentus 7200 FDE.1 SATA provides powerful features for cryptographically erasing the drive for dis-

posal or repurposing. The drive uses the ATA Security Erase Prepare (F3) and ATA Security Erase (F4) com-

mands to perform the cryptographic erase.

3.6.1

Secure Erase procedure

Using the Security Erase commands, the drive's cryptographic key can be replaced according to the following

procedure:

1. Consumer boots up the computer normally according to the Consumer Usage section above.

2. Consumer invokes software or BIOS option for Erase.

3. The software or BIOS queries the user for either the User or Master password.

4. The software or BIOS issues the Security Erase Prepare (F3) command.

5. The software or BIOS issues the Security Erase Unit (F4) command.

Select the Enhanced erase for cryptographic key erasure that completes in less than one second.

3.6.2

Drive State after Secure Erase

Upon completion of the erase sequence, the existing cryptographic key is erased, rendering all existing data

unintelligible, and the drive has been returned to the manufactured state as follows:

• The existing encryption key is deleted.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

• A new random encryption key has been created on the drive.

• Encryption function is active and functioning.

The new key is used to encrypt all user data on write and decrypt on read.

• The user interface to the drive is active and all read and write commands are allowed.

• The ATA User password is reset to null (no value).

• The ATA Master password is not modified

The ATA Master password is the same value as it was before the erase.

• The ATA Security is set to the Unlocked state.

No password is required to access the drive.

The drive may now be disposed of safely, or the drive may be returned to service for another consumer follow-

ing the initialization procedure defined above. Drives returned to Seagate for warranty purposes have special

requirements. See the warranty information in Section 2.13 for additional details.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.0

Serial ATA interface

These drives use the industry-standard Serial ATA (SATA) interface that supports FIS data transfers. It sup-

ports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.

The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT

Attachment” specification.

4.1

Hot-Plug compatibility

Momentus 7200 FDE.1 SATA drives incorporate connectors which enable you to hot plug these drives in

accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specifi-

cation can be downloaded from http://www.serialata.org. This device requires a COMRESET from the host

after a hotplug event.

4.2

Serial ATA device plug connector pin definitions

Table 5 summarizes the signals on the Serial ATA interface and power connectors..

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 5:

Serial ATA connector pin definitions

Segment Pin

Function

Ground

A+

Definition

2nd mate

Differential signal pair A from Phy

A-

Ground

B-

2nd mate

Differential signal pair B from Phy

B+

Signal

Ground

2nd mate

Key and spacing separate signal and power segments

P10

P11

V₃₃

3.3V power

V₃₃

3.3V power

V₃₃

3.3V power, pre-charge, 2nd mate

Ground

V₅

1st mate

2nd mate

5V power, pre-charge, 2nd mate

V₅

5V power

Power

V₅

5V power

Ground

Reserved

2nd mate

The pin corresponding to P11 in the backplane receptacle connector is also reserved

The corresponding pin to be mated with P11 in the power cable receptacle connector

shall always be grounded

P12

P13

P14

P15

Ground

V₁₂

1st mate.

12V power, pre-charge, 2nd mate

12V power

V₁₂

12V power

Notes:

1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.

2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this

case, the mating sequences are:

• the ground pins P4 and P12.

• the pre-charge power pins and the other ground pins.

• the signal pins and the rest of the power pins.

3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when

installed in a blind-mate backplane configuration.

4. All used voltage pins (V_x) must be terminated.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.1

ATA Security policy exceptions

In the ATA Security Interface mode, the drive conforms to the ATA Security Policy, except the following desir-

able exceptions to implement the desired Momentus 7200 FDE.1 SATA behavior:

Upon execution of the secure erase sequence, the drive will have the following behavior:

• All secure erase modes will instantaneously delete the encryption key rendering all user data unintelligible.

• A new encryption key will be generated inside the drive replacing the previous encryption key.

• The new encryption/decryption key will be applied to the data for all subsequent writes/reads prior to the

next secure erase sequence.

• The user password will be cleared to a null value.

• The master password will retain the current value per the ATA specification.

Note. On completion of this sequence, the user is assured that all sectors on the drive are unintelligible and

the drive is returned to the default factory state. It is then immediately ready for disposal or repurpos-

ing.

The ATA Security Erase Unit Command provides for normal and enhanced erase modes as follows:

Table 6:

ATA Security Erase Unit bits

Word

Content

Control word

Bit 0

Identifier

0 = Compare User password

1 = Compare Master password

0 = Normal Erase

Bit 1

Erase mode

Reserved

1 = Enhanced Erase

Bit (15:2)

1 - 16

Password (32 bytes)

Reserved

17 - 255

Choosing enhanced erase mode will simply perform the cryptographic erase described above, and return sta-

tus almost immediately. This is the recommended option.

To maintain consistency with the ATA Security specification, Momentus 7200 FDE.1 SATA drives provide an

option to perform the Normal Erase mode.

Choosing normal erase will result in the drive performing the cryptographic erase which is the same as choos-

ing enhanced erase.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.2

DriveTrust Mode support

Identify Page - Word 150 decimal (0x96h)- Bit 12 Identifies DriveTrust Support.

Value = 1 = DriveTrust is supported

Table 7:

DriveTrust Identify Page

Ident Value

BIT set

Bit

Description

Vendor specific

DriveTrust Enabled

Vendor specific

DriveTrust Supported

Vendor specific

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.3

Full Disc Encryption support

Identify Page--Word 243 decimal (0xF3h)--bit 14 indicates Full Disc Encryption capability.

1 = Full Disc Encryption supported.

Table 8:

Full Disc Encryption Identify Page

Ident Value

BIT set

Bit

Description

Vendor specific

Full Disc Encryption

Vendor specific

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.4

Supported ATA commands

The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA

commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See “S.M.A.R.T. com-

mands” on page 41 for details and subcommands used in the S.M.A.R.T. implementation.

Table 9:

Supported commands

ATA Security API

Unlocked Frozen

DriveTrust Security API

Code

Secure

State

Authenticated

State

Command

Locked

Special Commands

TRUSTED RECEIVE (PIO)

TRUSTED RECEIVE DMA

TRUSTED SEND (PIO)

TRUSTED SEND DMA

Executable Executable Executable Executable

Normal Commands

Executable

CHECK POWER MODE

CONFIGURE STREAM

Executable Executable Executable Executable

Executable

Aborted

Executable Executable Aborted

DEVICE CONFIGURATION Aborted

DEVICE RESET

DOWNLOAD MICROCODE Aborted

Executable Executable Executable Executable

Aborted Aborted Aborted

Executable Executable Executable Executable

EXECUTE DEVICE

DIAGNOSTIC

Executable

FLUSH CACHE

Aborted

Executable Executable Aborted

Executable

FLUSH CACHE EXT

IDENTIFY DEVICE

Executable Executable Executable Executable

IDENTIFY PACKET

DEVICE

IDLE

Executable Executable Executable Executable

Executable

IDLE

IDLE IMMEDIATE

NOP

READ BUFFER

READ DMA

READ DMA EXT

Aborted

Executable Executable Aborted

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 9:

Supported commands

ATA Security API

Unlocked Frozen

DriveTrust Security API

Code

Secure

State

Authenticated

State

Command

READ LOG EXT

Locked

Executable Executable Executable Executable

Executable

READ MULTIPLE

READ MULTIPLE EXT

Aborted

Executable Executable Aborted

READ NATIVE MAX

ADDRESS

Executable Executable Executable Executable

READ NATIVE MAX

ADDRESS EXT

Executable Executable Executable Executable

Executable

READ SECTOR(S)

Aborted

Executable Executable Aborted

Executable

READ SECTOR(S)

READ SECTOR(S) EXT

READ STREAM DMA EXT

READ STREAM EXT

READ VERIFY SECTOR(S) Aborted

READ VERIFY SECTOR(S)

EXT

Aborted

RECALIBRATE

Executable Executable Executable Executable

Executable

Aborted

SECURITY DISABLE

PASSWORD

Aborted

Executable Aborted

Aborted

SECURITY ERASE

PREPARE

Executable Executable Aborted

Aborted

SECURITY ERASE UNIT

SECURITY FREEZE LOCK

Aborted

Executable Executable Aborted

Executable

Aborted

SECURITY SET PASS-

WORD

Executable Aborted

Aborted

SECURITY UNLOCK

SEEK

Executable Executable Aborted

Executable

Executable Executable Executable Executable

SET DRIVE PARAMETERS Executable Executable Executable Executable

SET FEATURES

Executable Executable Executable Executable

SET MAX ADDRESS

Aborted

Executable Executable Aborted

F9 / 00

SET MAX ADDRESS EXT

Executable

F9 / 01

SET MAX SET

PASSWORD

F9 / 02

SET MAX LOCK

Aborted

Executable Executable Aborted

Executable

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 9:

Supported commands

ATA Security API

Unlocked Frozen

DriveTrust Security API

Code

Secure

State

Authenticated

State

Command

Locked

F9 / 04

SET MAX FREEZE LOCK

Aborted

Executable Executable Aborted

Executable

F9 / 03

SET MAX UNLOCK

Aborted

SET MULTIPLE MODE

SLEEP

Executable Executable Executable Executable

Executable

SLEEP

B0 / D9

SMART DISABLE

OPERATIONS

B0 / D2

SMART ENABLE/DISABLE

AUTOSAVE

Executable Executable Executable Executable

Executable

B0 / D8

SMART ENABLE

OPERATIONS

B0 / D4

SMART EXECUTE

OFF-LINE

IMMEDIATE

B0 / 08

SMART READ DATA

SMART READ LOG

Executable Executable Executable Executable

Executable

B0 / D5

B0 / DA

SMART RETURN STATUS

SMART WRITE LOG

B0 / D6

STANDBY

Executable Executable Executable Executable

Executable

STANDBY

STANDBY IMMEDIATE

WRITE BUFFER

WRITE DMA

Aborted

Executable Executable Aborted

WRITE DMA

WRITE DMA EXT

WRITE DMA FUA EXT

WRITE LOG EXT

WRITE MULTIPLE

WRITE MULTIPLE EXT

WRITE SECTOR(S)

WRITE SECTOR(S) EXT

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 9:

Supported commands

Command

ATA Security API

Unlocked Frozen

DriveTrust Security API

Code

Secure

State

Authenticated

State

Locked

WRITE STREAM DMA EXT Aborted

WRITE STREAM EXT Aborted

Executable Executable Aborted

Executable

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.5

Identify Device command

The Identify Device command (command code EC ) transfers information about the drive to the host following

power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table

below. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary

with the state of the drive.

The following commands contain drive-specific features that may not be included in the Serial ATA specifica-

tion.

Word

Description

Value

0C5A

Configuration information:

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

Number of logical cylinders

ATA-reserved

16,383

0000

Number of logical heads

Retired

0000

Retired

0000

Number of logical sectors per logical track: 63

Retired

003F

7–9

10–19

0000

Serial number: (20 ASCII characters, 0000 = none)

ASCII

Retired

Obsolete

0000

0400

0000

x.xx

23–26

Firmware revision (8 ASCII character string, padded with

blanks to end of string)

27–46

Drive model number: (40 ASCII characters, padded with

blanks to end of string)

ST9320424AS

ST9250424AS

ST9160414AS

ST9120414AS

ST9320424ASG

ST9250424ASG

ST9160414ASG

ST9120414ASG

ST980414ASG

(Bits 7–0) Maximum sectors per interrupt on Read multiple

and Write multiple (16)

8001

Reserved

0000

Standard Standby timer, IORDY supported and may be dis-

abled

2F00

ATA-reserved

0000

0200

PIO data-transfer cycle timing mode

Retired

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Word

Description

Value

0007

Words 54–58, 64–70 and 88 are valid

Number of current logical cylinders

Number of current logical heads

xxxx

Number of current logical sectors per logical track

Current capacity in sectors

57–58

Number of sectors transferred during a Read Multiple or

Write Multiple command

60–61

Total number of user-addressable LBA sectors. This field

contains a value that is one greater than the total number of

user-addressable sectors. The maximum value that shall be

placed in this field is 0FFFFFFh. The 0FFFFFFFh value

applies to all capacities over 137 Gbytes (see Section 2.2

and 2.3 for related information).

ST9320424AS = 0FFFFFFFh

ST9320424ASG = 0FFFFFFFh

ST9250424AS = 0FFFFFFFh

ST9250424ASG = 0FFFFFFFh

ST9160414AS = 0FFFFFFFh

ST9160414ASG = 0FFFFFFFh

ST9120414AS = 234,441,648

ST9120414ASG = 234,441,648

ST980414ASG = 156,301,488

Retired

0000

Multiword DMA active and modes supported

(see note following this table)

xx07

Advanced PIO modes supported (modes 3 and 4 supported)

0003

0078

Minimum multiword DMA transfer cycle time per word

(120 nsec)

Recommended multiword DMA transfer cycle time per word

(120 nsec)

0078

Minimum PIO cycle time without IORDY flow control

(240 nsec)

00F0

Minimum PIO cycle time with IORDY flow control (120 nsec)

ATA-reserved

0078

0000

0508

0000

0048

0040

69–74

Queue depth

Serial ATA capabilities

ATA-reserved

Serial ATA features supported

Serial ATA features enabled

Major version number

003E

Minor version number

0000

Command sets supported

Command sets support extension

346B

7D09

61E3

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Word

Description

Value

34xx

Command sets enabled

BC09

Command sets enable extension

61E3

Ultra DMA support and current mode

(see note following this table)

xx7F

Security erase time

0001

Enhanced security erase time

Master password revision code

FFFE

Hardware reset value

xxxx

(see description following this table)

Auto acoustic management setting

ATA-reserved

xxxx

95–99

0000

100–

103

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

ST9320424AS = 625,142,448

ST9320424ASG = 625,142,448

ST9250424AS = 488,397,168

ST9250424ASG = 488,397,168

ST9160414AS = 312,581,808

ST9160414ASG = 312,581,808

ST9120414AS = 234,441,648

ST9120414ASG = 234,441,648

ST980414ASG = 156,301,488

These words are required for drives that support the 48-bit

addressing feature. Maximum value: 0000FFFFFFFFFFFFh.

104–

127

ATA-reserved

0000

128

Security status

0021

129–

159

Seagate-reserved

xxxx

160–

254

ATA-reserved

Integrity word

0000

xxA5

255

Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data:

Description (if bit is set to 1)

Bit

Word 63

Multiword DMA mode 0 is supported.

Multiword DMA mode 1 is supported.

Multiword DMA mode 2 is supported.

Multiword DMA mode 0 is currently active.

Multiword DMA mode 1 is currently active.

Multiword DMA mode 2 is currently active.

Word 88

Bit

Ultra DMA mode 0 is supported.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Ultra DMA mode 1 is supported.

Ultra DMA mode 2 is supported.

Ultra DMA mode 3 is supported.

Ultra DMA mode 4 is supported.

Ultra DMA mode 0 is currently active.

Ultra DMA mode 1 is currently active.

Ultra DMA mode 2 is currently active.

Ultra DMA mode 3 is currently active.

Ultra DMA mode 4 is currently active.

Ultra DMA mode 5 is currently active.

Word 93

Bit

1 = 80-conductor cable detected, CBLID above VIH

0 = 40-conductor cable detected, CBLID below VIL

4.2.6

Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives

this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-

rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.

Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the

Features register are defined as follows:

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 10:

Set Features command values

Enable write cache (default).

Set transfer mode (based on value in Sector Count register).

Sector Count register values:

00 Set PIO mode to default (PIO mode 2).

01 Set PIO mode to default and disable IORDY (PIO mode 2).

08 PIO mode 0

09 PIO mode 1

0A PIO mode 2

0B PIO mode 3

0C PIO mode 4 (default)

20 Multiword DMA mode 0

21 Multiword DMA mode 1

22 Multiword DMA mode 2

40 Ultra DMA mode 0

41 Ultra DMA mode 1

42 Ultra DMA mode 2

43 Ultra DMA mode 3

44 Ultra DMA mode 4

45 Ultra DMA mode 5

46 Ultra DMA mode 6

Disable read look-ahead (read cache) feature.

Disable write cache

Enable read look-ahead (read cache) feature (default).

Report full capacity available

Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-

cated above.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

4.2.7

S.M.A.R.T. commands

S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-

tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines

that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.

S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.

commands and implementation, see the Draft ATA-5 Standard.

SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-

nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:

http://seatools.seagate.com.

This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that

supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the

drive uses.

Table 11:

S.M.A.R.T. commands

Code in features register

S.M.A.R.T. command

S.M.A.R.T. Read Data

Vendor-specific

S.M.A.R.T. Enable/Disable Attribute Autosave

S.M.A.R.T. Save Attribute Values

S.M.A.R.T. Execute Off-line Immediate (runs DST)

Vendor-specific

S.M.A.R.T. Enable Operations

S.M.A.R.T. Disable Operations

S.M.A.R.T. Return Status

Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04

(abort) is written to the Error register.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

5.0

Compatibility summary

5.1

Installation considerations

Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard

drive. Refer to your system’s user manual for the location of the hard drive compartment and the specific

instructions regarding replacement. Refer to your system manufacturer’s support website for the most up-to-

date information. Read and follow all instructions regarding the proper steps to be taken when replacing the

system hard drive.

Some mobile systems are sealed and require specialized tools to gain access to the hard drive. Special train-

ing or tools may be needed to service some mobile computers. In some cases, opening the case may void

your warranty. Consult your system documentation. Seagate recommends taking your system to an authorized

service technician to replace your hard drive.

5.2

System Compatibility using WIndows XP SP2

Seagate Product Assurance has tested Momentus drives in systems using ATA Security mode. Testing

included multiple BIOS versions and the Windows XP SP2 Pro operating system. This testing was done to

demonstrate compatibility with various hardware and software configurations.

5.2.1

BIOS versions tested in ATA Security mode

The following list indicates the types of BIOS Seagate tested during the compatibility testing process. The list

highlights the major BIOS manufacturers. Individual systems contain variations of these BIOS versions and

were tested with regard to their implementation in the individual systems.

Table 12:

Tested BIOS versions with Windows XP SP2

Manufacturer

AMD

Model

BIOS Vendor

AMI

BIOS Release

MSIA7207NMS

V02.59

BIOS Version

V3.00

AMD

AMI

AMD

AMI

VER 02.59

VER 08.00.13

AMD

AWARD

AMD

V1.B

11/28/2005

AMD

V6.00

AMD

V6.00PG

786B9

AMD

11/17/2005

V2.00

AMD

PHOENIX

AWARD

6.00P

VER 6.00PG

AMD

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 12:

Tested BIOS versions with Windows XP SP2

Manufacturer

AMD

ATI

Model

BIOS Vendor

PHOENIX

INSYDE

AMI

BIOS Release

AWARD

BIOS Version

V5.1.39

AWARD

V6.00PG

AWARD

DELL

1.1.2

VER 2004Q3

0X5A31

RS400-200

RS480

R1.00

ATI

V02.59

ATI

AMI

V0707

ATI

AMERICAN

2/13/2006

MEGATRENDS

ATI

RS480

5000X

865

AMI

VER V3.1

3.13

ATI

AWARD

11/15/2005

11/22/2005

V1.04

ATI

VER1.09

ATI

PHOENIX

PHOENIX AWARD

PHOENIX

GATEWAY

ATI

V1.04

5/24/2005

A00

INTEL

DELL

510A 15A.0027

510A 15A.0043

510A 15A.0045

510A 15A.0066

786B1

865

V1.14

865

786B2

2.43

865

786B2

V1.11

865

786B2

V2.04

865

1.11

865

786B2 V1.10

10/26/2004

865

IBM

2CKT20AUS

510A.86A.0053

510A.86A.003

510A.86A.0033

DELL

865

INTEL

865

MICRON

PHOENIX

AWARD

865

A04

865

DELL

A06

865

DELL

A08

865

DELL

A10

865

875P

4/23/2003

875P-6A79BG00C

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 12:

Tested BIOS versions with Windows XP SP2

Manufacturer

INTEL

Model

875P

BIOS Vendor

GATEWAY

BIOS Release

510A.15A.0080

786B3

BIOS Version

875P

V1.09

875P

MICRON

PHOENIX

AMI

510A.86A.0076

DELL

875P

A02

875P

DELL

A03

915G/P

915M

3.1

8.00.10 11/12/04

5/6/2004

AMI

VVPGI635

786C1

AMI

V1.05

786C2

V1.02

IBM

2/4/2005

MPC

EV91510A.86A.0308

PHOENIX

AMI

AWARD BIOS 6.00PG

R01-03

A01

DELL

A03

A05

R0060F2

1.03A (77ET40WW)

1.05

915M

IBM

915M

PHOENIX

30/05/2005

915M

PHOENIX BIOS

1.06

915M

1.07

915M

R0071V0

R0160X5

V1.04

915M

925X

786C3

DELL

925X

PHOENIX

AWARD

A06

945G/P

NT94510J.86A.2487.2005.0906.

1451

INTEL

945G/P

786D1

AWARD

DELL

V1.03

V6.00PG

A01

945G/P

PHOENIX

DELL

945G/P

DELL

A02

945G/P

DELL

A05

945GM/PM

A02

DELL

A04

DELL

A05

DELL

A09

F.05

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 12:

Tested BIOS versions with Windows XP SP2

Manufacturer

INTEL

NVIDIA

SIS

Model

BIOS Vendor

IBM

BIOS Release

BIOS Version

1.02 (79ET56WW)

1.04 (7BET44WW)

945GM/PM

955X

IBM

LENOVO

PHOENIX

AMI

1.02 (7CET47WW)

1.10 (7FET50WW)

2.00 (79ETC0WW)

V1.20

12/21/2005

206

955X

786D3

AWARD

V1.02

955X

PHOENIX

W7158IMS

955X

975X

AMI

206

12/21/2005

A00

975X

AWARD

PHOENIX

INSYDE

PHOENIX

AMI

VER F1

DELL

E7221

G/P965

0X0070

NFORCE 4SLI

661

1.0.3

8/14/2006

1.0.3

DELL

2.1.0

V6.00PG

V310

2/7/2006

PHOENIX

AWARD

AMI

DELL

A04

V6.00PG

R1.00

V2.54

7/11/2005

6/13/2005

SIS

760

SIS

760

PHOENIX

AMI

V3.01

8/18/2004

VIA

K8M800

V0210

V2.54

VIA

AMI

8/30/2005

VIA

AWARD

V6.00PG

10/17/2005

5.2.2

DriveTrust compatibility verification

The systems documented in Table 13 passed DriveTrust compatibility tests running Windows XP Pro with ser-

vice pack 2 (SP2). The system configurations listed below support the Trusted Send/Receive capabilities

required for pre-boot and other SeaCOS (dcard) features. Refer to your DriveTrust software vendor for addi-

tional considerations.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 13:

DriveTrust compatibility

Chipset

Manufacturer Southbridge System Vendor System Model

SATA Mode

ATA

BIOS

Intel

ICH6M

ICH7M

LW40-DOX1

K40D

Phoenix OLMPSF07

Phoenix1.00

TCL

Acer

ATA

Aspire 3690 BL50

Aspire 5572WXMI

Aspire 9410 MS2195

Aspire 9800 LA01

Aspire 9815WKH1

Travelmate 3270-ZR1

6263

ATA

Phoenix V3.50

Phoenix V1.3505

Phoenix V1.18

Phoenix I1.05

Phoenix V2.12

Phoenix V1.3505

Phoenix 2.03

Asus

ATA

Asus

Dell

F9J

ATA

G2P

ATA

Asus 009.012.001.027.A07408.025

Asus 13.13.I06405.009

Asus V310

R1F

ATA

V1JP

ATA

Inspiron 6400/E1505

Inspiron 9400/E1705

Precision M65

Precision M90

XPS M1210

XPS M1710

FMVNE2KD3

FMVNF70W

FMVNS5C4

FMVNX70WD

FMVNX90RW

ATA

Dell A09

ATA

Dell A04

ATA

Dell A05

ATA

Dell A04

ATA

Dell A04

ATA

Dell A02

Fujitsu

AHCI

Phoenix V1.09

Fujitsu Phoenix 1.04

Fujitsu Phoenix 1.25

Fujitsu Phoenix 1.06

Phoenix V1.04

Lifebook FMV8250

E-100M

ATA

Phoenix V1.02

PhoenixBIOS 76.09

PhoenixBIOS 71.04

PhoenixBIOS 72.02

PhoenixBIOS 71.04

HP F.08

Gateway

HP-BPC

AHCI

M465-E

M685-E

NX560X

Compaq NC4400

Compaq NC6400

Compaq NC8430

Compaq NW8440

Compaq NW9440

Compaq NX7400

Compaq NX8420

Compaq NX9420

Compaq TC4400

Pavilion DV2000T

Pavilion DV6000T

Pavilion DV9000T

HP F.08

HP F.12

HP F.1B

HP F.15

HP F.1C

HP F.0B

HP F26

HP F27

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 13:

DriveTrust compatibility

Chipset

Manufacturer Southbridge System Vendor System Model

SATA Mode

AHCI

BIOS

ICH7M

Intel

HP-BPC

Presario V3000T

Presario V6000T

HP F26

HP F.29

AHCI

Lenovo China Sunrise 210

ATA

Phoenix Trustedcore 1.0B-

1264-8A20

Sunrise 410

ATA

Phoenix Trustedcore LE4

Q3B72

Sunrise 410L

Phoenix Trustedcore LE4

Q3B72

TIAN YI F30A

TIAN YI F40A

ATA

Phoenix Trustedcore Q3A82

V1.08

ATA

LGE-DMLGR40(B)

AHCI

ATA

Phoenix LHONSF04

Phoenix 3A22-1284-1A22

Phoenix R0170J3

Phoenix R0107J3

Phoenix

NEC-SAS

NEC Versa M160

NEC Versa M360

VGN FE31B/W

VNG FE51B/H

VGN-AR92S

VGN-C71B/W

VGN-FE53B/W

VGN-N51HB

VGN-SZ73B/B

K42

ATA

Sony

ATA

Phoenix

ATA

Phoenix

ATA

Phoenix

ATA

Phoenix N0G72-13

Phoenix 1.08

TCL

ATA

Toshiba

Acer

Satelite M100

AS9920

ATA

Phoenix V1.20

Phoenix V1.11.0

Phoenix V1.08

Phoenix V1.3708

Acer

ICH8M

AHCI

ATA

Aspire 4720

Aspire 5920G

Aspire 7720WSMI

G1S

AMI V1.12

Asus

Dell

Asus

G2S

Asus 1000B50001

Phoenix A00

Inspiron 1420

Inspiron 1720

Precision M4300

Precision M6300

FMB BIBLO NF70X

FMVNE5FD4

Celsius H250

Lifebook S6410

AHCI

ATA

Phoenix A00

Phoenix A02

AHCI

Phoenix A00

Fujitsu

Phoenix V1.12

Fujitsu Phoenix 1.06

Phoenix 1.08

Fujitsu

Siemens

Phoenix 1.11

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 13:

DriveTrust compatibility

Chipset

Manufacturer Southbridge System Vendor System Model

SATA Mode

AHCI

ATA

BIOS

Intel

ICH8M

HP-BPC

Compaq 2210B

Compaq 6510B

Compaq 6710B

Compaq 6720S

Compaq 6910P

Compaq 8710P

Pavilion DV2500T

Pavilion DV6500T

Pavilion DV9500T

Pavilion HDX

HP F00

HP F10

HP F.0B

HP F.06

Phoenix F.21

Phoenix F.33

Levovo China TIANYI F41A

XURI C430A

Lenovo 05N23WW (V1.03)

Lenovo Q3B14

Lenovo 1.06T05

AMI A1636IL 1 V1.17

Phoenix STNYSF05

Phoenix COLSSF0B

Phoenix 05AB

Phoenix 06ST

Phoenix A 0B-0401-0011

Phoenix 1.00TG

Phoenix V1.14

Phoenix A00

ATA

XURI C430G

ATA

ZHAOYANG K42A

AHCI

ATA

LGE-DML GE50(B)

LGE-DML GM1(B)

LGE-DML GP3

SEC-NT-R70(B)

SQ45S70S

ATA

AHCI

ATA

Samsung

ATA

TCL

T45

AHCI

ATA

Trigem

Acer

Dell

N8393WFGK

AMD(ATI)

SB600

Travelmate 5520G

Inspiron 1521

ATA

Inspiron 1721

ATA

Phoenix 2 3.1

Phoenix 1.00

Dell 1.4.0

Trigem

Dell

N8172SH1K

ATA

Inspiron 1501

ATA

Nvidia

MCP51

HP-BPC

Pavilion DV2000Z

Pavilion DV6000Z

Pavilion TX1000Z

Pavilion TX1200

Presario V6000Z

ATA

HP F34

ATA

HP F38

ATA

HP F.18

HP-BPC

ATA

Phoenix F.1C

HP F.38

ATA

5.3

Operating system versions tested

This list indicates the types of Operating Systems Seagate tested during the compatibility testing process. Sev-

eral variations of these operating systems have been tested.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Table 14:

Supported operating systems

Manufacturer

Microsoft

Version/Release

Windows Server 2003 (Compatibility evaluated, but not tested)

Windows XP, XP Pro, XP Home (Service Pack 2) (multiple languages)

Microsoft

Windows Vista.

Note: Some systems will require a “hotfix” from Microsoft. Refer to www.miocrosoft.com and

search for knowledgebase (KB) article number 943170 for important information about obtaining

and installing the necessary operating system fixes necessary to successfully use Vista with FDE

drives in DriveTrust mode. These fixes are not required to use the drive in ATA Security mode.

5.4

Compatibility test configurations

Tests are performed to ensure functionality to the ATA/ATAPI-7 specification and are constantly evolving to

match the evolution of the ATA/ATAPI specifications. Momentus 7200 FDE.1 SATA drives should be expected

to be largely compliant to the emerging ATA/ATAPI-8 specification.

Exceptions to the specifications for the Momentus 7200 FDE.1 SATA drives are listed in Section 4.0.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

6.0

Seagate Technology support services

Internet

For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is

available 24 hours daily by email for your questions.

Presales Support:

[email protected]

Technical Support:

[email protected]

Warranty Support:

http://www.seagate.com/support/service/index.html

mySeagate

my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides

self-service access to critical applications, personalized content and the tools that allow our partners to

manage their Seagate account functions. Submit pricing requests, orders and returns through a single,

password-protected Web interface-anytime, anywhere in the world.

spp.seagate.com

spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You

may register for customized communications that are not available on the web. These communications contain

product launch, EOL, pricing, promotions and other channel-related information. To learn more about the

benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.

Seagate Service Centers

Presales Support

Our Presales Support staff can help you determine which Seagate products are best suited for your specific

application or computer system, as well as product availability and compatibility.

Technical Support

Seagate technical support is available to assist you online at support.seagate.com or through one of our call

centers. Have your system configuration information and your “ST” model number available.

SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or

comments 24 hours daily and exchange messages with a technical support specialist during normal business

hours for the call center in your region.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Customer Service Operations

Warranty Service

Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct

customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-

related issues. Resellers or end users of drive products should contact their place of purchase or Seagate

warranty service for assistance. Have your serial number and model or part number available.

Data Recovery Services

Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery

services labs are currently located throughout the world. . Additional information, including an online request

form and data loss prevention resources, is available at http://services.seagate.com/index.aspx

Authorized Service Centers

Seagate Service Centers are available on a global basis for the return of defective products. Contact your

customer support representative for the location nearest you.

USA/Canada/Latin America support services

For an extensive list of telephone numbers to technical support, presales and warranty service in USA/

Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.

Global Customer Support

Presales, Technical, and Warranty Support

Call Center

USA, Canada,

and Mexico

Toll-free

Direct dial

1-800-SEAGATE

+1-405-324-4700

Data Recovery Services

Call Center

Toll-free

Direct dial

FAX

USA, Canada,

and Mexico

1-800-475-01435

+1-905-474-2162

1-800-475-0158

+1-905-474-2459

Europe, the Middle East and Africa Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the

Middle East and Africa, go to the "Contact Us" page on www.seagate.com.

Asia/Pacific Support Services

For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,

go to the "Contact Us" page on www.seagate.com.

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

current 5

cycles 17

Cylinders 7

Index

ACA 18

acoustics 6, 15

Active mode 12

AFR 17

Agency certification 17

Altitude 13

Altitude, nonoperating 6

Altitude, operating 6

Ambient temperature 6, 13

ambient temperature 9

Annualized Failure Rate 17

Annualized Failure Rate (AFR) 6

Areal density 5, 8

ATA data-transfer modes supported 5

ATA-standard commands 32

Australia/New Zealand Standard AS/NZS3548 1995

data-transfer rates 1

DC power 10

Default logical geometry 7

density 5

diagnostic software 1

dimensions 23

Discs 5

dissipation 10

drive monitoring 1

drive self-test 1

Electrical fast transient 16

Electromagnetic compatibility 18

Electromagnetic Compatibility Directive (89/336/EEC)

Electromagnetic immunity 15

Electrostatic discharge 16

electrostatic discharge (ESD) 21

EN 55022, Class B 18

EN 55024 18

Australian Communication Authority (ACA) 18

Australian C-Tick 18

Average seek time 9

Average seek, read 5

bels 6

BIOS manufacturers 43

BPI 5

buffer 1, 5, 8

burst 1

EN 60950 17

Environmental protection 20

Environmental specifications 13

error-correction algorithms 1

errors 6, 17

ESD 21

EU 18

Bytes per sector 5, 7

European Union (EU) requirements 18

European Union Restriction of Hazardous Substanc-

es 20

cables and connectors 22

Cache 5

cache 1, 8

capacity 7

case temperature 13

CE mark 18

certification 17

FCC verification 18

Federal Communications Commission 18

Formatted capacity 7

Formatted Gbytes 5

chemical substances 20

China RoHS directive 20

Class B computing device 18

commands 32

compatibility 18, 43

compatibility summary 43

compatibility test configurations 50

Conducted noise 11

Conducted RF immunity 16

Configuring the drive 21

connectors 22

Gbytes 7

geometry 7

gradient 6

Guaranteed sectors 5, 7

guaranteed sectors 7

handling 21

Handling precautions 21

CSA C22.2 (950) 17

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

heads 7

Height 5

height 8

Operating vibration 14

OS manufacturers 49

Humidity 13

humidity 6

Physical characteristics 8

Physical organization 8

Physical read/write heads 5

point-to-point 22

Power consumption 10

power dissipation 10

I/O data-transfer rate 5, 8

Identify Device command 36

Idle 10

Idle and Standby timers 12

Idle mode 6, 12

power management 12

power on/off cycles 17

Power specifications 10

Power-management modes 12

Power-on to Ready 9

Power-on to ready 5

precautions 21, 23

programmable power management 12

Idle mode power 10

IEC950 17

Information Technology Equipment (ITE) 18

Input noise ripple 11

Interface 8

interface 27

Interleave 8

Internal data transfer rate 5

Internal data-transfer rate 8

ITE 18

quick reference 5

Radiated RF immunity 16

Radio and television interference 18

radio frequency (RF) 15

random track location 10

read errors 6, 17

Read Multiple 1

Read/write heads 7

Read/write power 6

read/write power and current 10

Recording density 5, 8

Recording method 8

Recording technology 8

Relative humidity 6, 13

Reliability 17

Korean RRL 18

latency 5

LBA mode 7

Length 5

length 8

Load/Unload 17

logical geometry 7

maximum temperature 13

monitoring 1

mounting 23

mounting screws 14

mounting the drive 21

resistance 11

RF 15

RoHS 20

RPM 5

RRL 18

noise 11

nominal power 9

S.M.A.R.T. drive monitoring 1

Safety certification 17

SATA 8, 27

screws 14, 23

SeaTools 1

Nonoperating shock 14

Nonoperating vibration 14

Nonrecoverable read errors 6

nonrecoverable read errors 17

sector 7

sectors 7

Operating shock 14

operating system 43

Sectors per track 7

seek mode 10

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Seek power 5

Seek time 9

Wet bulb temperature 6, 13

Width 5

seek time 5

width 8

Seeking 10

Write Multiple 1

Self refresh, low power 12

Serial ATA 8

Serial ATA (SATA) interface 27

servo electronics 10

Shock 14

Shock, nonoperating 6

Shock, operating 6

single-track seeks 9

Sleep 10

Sleep mode 6, 12

sound power 6

Specification summary table 5

Spindle speed 5, 8

Spinup 10

spinup power 10

Standby 10

Standby mode 6, 10, 12

Standby to Ready 9

Standby to ready 5

Start/stop times 9

Startup current 5

static-discharge 21

support services 51

Surge immunity 16

technical support services 51

temperature 6, 9, 13

Temperature gradient 6, 13

timers 12

TPI 5

Track density 5, 8

Track-to-track seek time 5, 9

TUV North America 17

UL 1950 17

Vibration 14

Vibration, nonoperating 6

Vibration, operating 6

Voltage dips, interrupts 16

Voltage tolerance 6, 11

Warranty 17

Weight 5

weight 8

Momentus 7200 FDE.1 SATA Product Manual, Rev. A

Seagate Technology LLC

920 Disc Drive, Scotts Valley, California 95066-4544, USA

Publication Number: 100515958, Rev. A, Printed in USA

TRENDnet Computer Accessories TK 210 User Manual
Sprint Nextel Cell Phone Dura XT User Manual
Sony Radio Cassette Player FX485 User Manual
Seagate DB35 SERIES 72002 ST3500841ACE User Manual
Samsung Spinpiont M7 HM250HI User Manual
Samsung SGH B300 User Manual
Samsung GH68 23417A User Manual
Sabrent EC UEIS7 User Manual
Philips SPD5220 User Manual
Nokia CLASSIC 6500 User Manual