Seagate MOMENTUS ST94813A User Manual

Product Manual

Momentus 5400.2

ST9120821A

ST9100824A

ST98823A

ST96812A

ST94813A

ST93811A

100367120

Rev. B

August 2007

Contents

1.0

2.0

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Time to ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Power-management mode s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 0

2.10

Environmental specification s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Altitud e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Vibratio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2

Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.14.1

2.14.2

2.14.3

Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.15

2.16

Environmental protectio n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6

Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.0

Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.1

3.2

Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.2.1

3.2.2

Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.3

Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.0

5.0

ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.1.1

4.1.2

4.1.3

Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Compatibility summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

BIOS versions teste d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1

Operating system versions tested . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Compatibility test configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Software utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Other certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.0

Seagate Technology support service s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3

Momentus 5400.2 PATA Product Manual, Rev. B

1.0

Introduction

This manual describes the functional, mechanical and interface specifications for the following Seagate^®

Momentus^®5400.2 drives:

• ST9120821A

• ST9100824A

• ST98823A

• ST96812A

• ST94813A

• ST93811A

These drives provide the following key features:

• 5,400-RPM spindle speed and 8-Mbyte buffer combine for superior performance.

• Quiet operation. Fluid Dynamic Bearing (FDB) motor.

• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

• Tunneling Magnetoresistive (TMR) recording heads.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• 800 Gs nonoperating shock and 250 Gs operating shock.

• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• The 3D Defense System™, which includes Drive Defense, Data Defense, and Diagnostic Defense, offers the

industry’s most comprehensive protection for disc drives.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

• Support for autodetection of master/slave drives that use cable select (CSEL).

Figure 1. Momentus 5400.2 PATA disc drive

Momentus 5400.2 PATA Product Manual, Rev. B

2.0

Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal

power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate

ST9120821A, ST9100824A, ST98823A, ST96812A, ST94813A and ST93811A model drives.

2.1

Specification summary

The specifications listed in this table are for quick reference. For details on specification measurement or

definition, see the appropriate section of this manual.

Table 1:

Specifications

Drive specification

ST9120821A ST9100824A ST98823A

ST96812A ST94813A

ST93811A

Formatted Gbytes (512 bytes/sec-

tor)

120

100

Guaranteed sectors

Bytes per sector

Physical read/write heads

Discs

234,441,648

195,371,568

156,301,488

117,210,240

78,140,160

58,605,120

512

Cache (Mbytes)

Recording density,

BPI (bits/inch typical)

778k

126k

Track density.

TPI (tracks/inch typical)

Areal density (Gbits/inch max)

98.2

Spindle speed (RPM)

5,400

Internal data transfer rate OD

(Mbytes/sec max)

I/O data-transfer rate

(Mbytes/sec max)

100

PIO modes 0–4

Multiword DMA modes 0–2

Ultra DMA modes 0–5

ATA data-transfer

modes supported

Height

9.5 +/-0.2 mm (0.374 +/-.008 inches)

Width

69.85 +/-0.25 mm (2.750 +/-0.010 inches)

Length

100.2 +/-0.25 mm (3.945 +/-0.010 inches)

Weight (typical)

100 grams (0.22 lb)

Average latency (msec)

Power-on to ready (sec typical)

Standby to ready (sec typical)

Startup current 5V (typical)

5.6

3.5

3.0

1.0 amps

Track-to-track seek time

(msec typical)

1.0 (read), 1.5 (write)

Momentus 5400.2 PATA Product Manual, Rev. B

Table 1:

Specifications

Drive specification

ST9120821A ST9100824A ST98823A

ST96812A ST94813A

ST93811A

Average seek time (msec typical) 12.5

Average seek, read (msec typical) 12.5

Average seek, write (msec typical) 14.5

Full-stroke seek (msec)

Seek power (typical)

Read/write power (typical)

Idle mode (typical, low power)

Standby mode

22 (typical); 24 (max)

2.0 watts

Read: 1.8 watts; Write: 1.8 watts

0.80 watts

0.26 watts (typical)**

5V ± 5%

Sleep mode

Voltage tolerance

(including noise)

Ambient temperature

5° to 55°C (operating), –40° to 70°C (nonoperating)

Temperature gradient

(°C per hour max,

noncondensing)

20°C (operating)

30°C (nonoperating)

Relative humidity

(noncondensing)

5% to 90% (operating)

5% to 95% (nonoperating)

Relative humidity gradient

30% per hour max

Wet bulb temperature (°C max)

30°C (operating)

40°C (nonoperating)

Altitude, operating

–304.8 m to 3,048 m (–1000 ft to 10,000 ft)

–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)

Altitude, nonoperating

(below mean sea level, max)

Shock, operating

(Gs max at 2 msec)

250

800

900

400

Shock, nonoperating

(Gs max at 2 msec)

Shock, nonoperating

(Gs max at 1 msec)

Shock, nonoperating

(Gs max at 0.5 msec)

Vibration, operating

(max displacement may

apply below 10 hz)

1.0 Gs (0 to peak, 5–500 Hz)

5.0 Gs (0 to peak, 10–500 Hz)

Vibration, nonoperating

(max displacement may apply

below 22 hz)

Drive acoustics, sound power

(bels), 2 disc

2.4 (typical)

2.6 (max)

Idle*

2.9 (typical)

3.1 (max)

Performance seek

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Load/Unload (U/UL) cycles

1 per 10 bits read

0.73%

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

32°C, 80% relative humidity

5°C, 80% relative humidity

5°C, 10% relative humidity

55°C, 16% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

Momentus 5400.2 PATA Product Manual, Rev. B

Table 1:

Specifications

Drive specification

ST9120821A ST9100824A ST98823A

ST96812A ST94813A

ST93811A

Service life

5 years

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the following web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial

number, model number (or part number) and country of purchase. The system will display the war-

ranty information for your drive.

Warranty

*During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

**Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes

will not contribute to battery power consumption.

2.2

Formatted capacity

Model

Formatted capacity

Guaranteed sectors

234,441,648

195,371,568

156,301,488

117,210,240

78,140,160

Bytes per sector

ST9120821A

ST9100824A

ST98823A

ST96812A

ST94813A

ST93811A

120 Gbytes

100 Gbytes

80 Gbytes

60 Gbytes

40 Gbytes

30 Gbytes

512

58,605,120

2.3

Default logical geometry

Cylinders

Read/write heads

Sectors per track

16,383

LBA mode

When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,

where n is the number of guaranteed sectors as defined above.

2.4

Physical organization

Model

Read/write heads

Number of discs

ST9120821A

ST9100824A

ST98823A

ST96812A

ST94813A

ST93811A

Momentus 5400.2 PATA Product Manual, Rev. B

2.5

Recording and interface technology

Technology

Specification

Interface

Parallel ATA

Recording method

RLL 0,11

Recording density BPI (bits/inch typical)

Track density TPI (tracks/inch typical)

778k

126k

Areal density (Gbits/inch max)

98.2

Spindle speed (RPM) (± 0.2%)

Internal data-transfer rate OD (Mbytes/sec max)

I/O data-transfer rate (Mbytes/sec max)

Interleave

5,400

100 (Ultra DMA mode 5)

1:1

Cache buffer

8 Mbytes (8,192 kbytes)

2.6

Physical characteristics

Height

(mm)

(inches)

9.5 +/–0.2

0.374 +/–0.008

Width

(mm)

(inches)

69.85 +/–0.25

2.750 +/–0.010

Length

(mm)

(inches)

100.2 +/–0.25

3.945 +/–0.010

Typical weight

(grams)

(pounds)

100

0.22

Momentus 5400.2 PATA Product Manual, Rev. B

2.7

Seek time

Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using

drive diagnostics. The specifications below are defined as follows:

• Track-to-track seek time is an average of all possible single-track seeks in both directions.

• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between

random tracks, less overhead.

Typical seek times (msec)*

Track-to-track

Read

1.0

Write

1.5

Average

12.5

22.0

5.56

14.5

24.0

5.56

Full-stroke

Average latency

*Measured in performance mode

Note. These drives are designed to consistently meet the seek times represented in this manual. Physical seeks,

regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values.

However, due to the manner in which these drives are formatted, benchmark tests that include command

overhead or measure logical seeks may produce results that vary from these specifications.

2.8

Time to ready

Max @ 25°C

Time to ready

Typical

3.5

Power-on to Ready (sec)

Standby to Ready (sec)

8.0

3.0

Momentus 5400.2 PATA Product Manual, Rev. B

2.9

Power specifications

The drive receives DC power (+5V) through the interface connector.

2.9.1 Power consumption

Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on

an average of drives tested, under nominal conditions, at 25°C ambient temperature.

• Spinup power

Spinup power is measured fromthe time ofpower-onto thetimethat the drive spindle reaches operating speed.

• Seek mode

During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does

not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on

three random seek operations every 100 msecs. This mode is not typical.

• Read/write power and current

Read/write power is measured with the heads on track, based on three 63 sector read or write operations

every 100 msecs.

• Idle mode power*

Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in

a random track location.

• Standby mode

During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/

write electronics are in power-down model

Table 2:

DC power

Power dissipation

Spinup (typical)

Seek

+5V average (25° C)

1.0 amps

2.00 watts

1.80 watts

1.70 watts

0.99 watts

0.80 watts

0.26 watts

Read

Write

Idle, performance mode*

Idle, active*

Idle, low power mode*

Standby

Sleep

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

Momentus 5400.2 PATA Product Manual, Rev. B

2.9.1.1

Typical current profile

Figure 2. Typical 5V startup and operation current profile

2.9.2

Conducted noise

Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on

the +5 volt line.

Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave

injected noise at up to 10 MHz.

Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current.

2.9.3

Voltage tolerance

Voltage tolerance (including noise):

5V ± 5%

Momentus 5400.2 PATA Product Manual, Rev. B

2.9.4

Power-management modes

The drive provides programmable power management to provide greater energy efficiency. In most systems,

you can control power management through the system setup program. The drive features the following

power-management modes:

Table 3:

Power management modes

Power modes

Active (operating)

Idle, performance

Idle, active

Heads

Spindle

Rotating

Stopped

Buffer

Tracking

Floating

Parked

Full power

Self refresh—low power

Idle, low power

Standby

Sleep

• Active mode

The drive is in Active mode during the read/write and seek operations.

• Idle mode

The buffer remains enabled in performance mode, and the drive accepts all commands and returns to Active

mode any time disc access is necessary.

• Standby mode

The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the

standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a

specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby

mode, the drive buffer is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest.

The drive accepts all commands and returns to Active mode any time disc access is necessary.

• Sleep mode

The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer

is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep

mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep

mode and enters Standby mode with all current translation parameters intact.

• Idle and Standby timers

Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and

begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive

activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive

accepts all commands and returns to Active mode when disc access is necessary.

Momentus 5400.2 PATA Product Manual, Rev. B

2.10

Environmental specifications

Ambient temperature

2.10.1

Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.

Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.

Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.

Operating

5° to 55°C (41° to 131°F)

Nonoperating

–40° to 70°C (–40° to 158°F)

2.10.2

Temperature gradient

Operating

20°C per hour (68°F per hour max), without condensation

30°C per hour (86°F per hour max), without condensation

Nonoperating

2.10.3

Humidity

2.10.3.1

2.10.3.2

2.10.4

Relative humidity

Operating 5% to 90% noncondensing (30% per hour max)

Nonoperating 5% to 95% noncondensing (30% per hour max)

Wet bulb temperature

Operating 30°C (86°F max)

Nonoperating 40°C (104°F max)

Altitude

Operating

Nonoperating

–304.8 m to 3,048 m (–1,000 ft to 10,000 ft)

–304.8 m to 12,192 m (–1,000 ft to 40,000 ft)

Momentus 5400.2 PATA Product Manual, Rev. B

2.10.5

Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive

mounting screws. Shock may be applied in the X, Y or Z axis.

2.10.5.1

Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum

operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more

than two times per second.

2.10.5.2

Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse

of 2 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 900 Gs based on a nonrepetitive half-sine shock pulse

of 1 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse

of 0.5 msec duration.

2.10.6

Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the

drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.10.6.1

Operating vibration

The following table lists the maximum vibration levels that the drive may experience while meeting the perfor-

mance standards specified in this document.

5–500 Hz 1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.

2.10.6.2

Nonoperating vibration

The following table lists the maximum nonoperating vibration that the drive may experience without incurring

physical damage or degradation in performance when subsequently put into operation.

5–500 Hz

5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.

Momentus 5400.2 PATA Product Manual, Rev. B

2.11

Acoustics

Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-

surements are consistent with ISO document 7779. Sound power measurements are taken under essentially

free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.

Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is

defined by the following equation:

(Number of seeks per second = 0.4 / (average latency + average access time)

Table 4:

Drive level acoustics

Idle*

Performance Seek

2.4 bels (typ)

2.6 bels (max)

2.9 bels (typ)

3.1 bels (max)

*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

2.12

Electromagnetic immunity

When properly installed in a representative host system, the drive operates without errors or degradation in

performance when subjected to the rradio frequency (RF) environments defined in the following table:

Table 5:

Electromagnetic immunity

Performance

level

Reference

standard

Test

Description

Electrostatic discharge

Radiated RF immunity

Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV

EN 61000-4-2: 95

EN 61000-4-3: 96

80 to 2,000 MHz, 10 V/m,

80% AM with 1 kHz sine

900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz

ENV 50204: 95

Electrical fast transient

Surge immunity

± 1 kV on AC mains, ± 0.5 kV on external I/O

± 1 kV differential, ± 2 kV common, AC mains

EN 61000-4-4: 95

EN 61000-4-5: 95

EN 61000-4-6: 97

Conducted RF immunity

150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz

sine

Power Frequency H-field 1 A/m, 50Hz/60Hz, 3 axes

immunity

EN 61000-4-8: 97

EN 61000-4-11: 94

Voltage dips, interrupts

30% Reduction for 25 cycles

>95% Reduction for 250 cycles

>95%, 0.5 cycles

A - 1) No upset or degradation in performance beyond manufacturer’s specified limits.

2) No data loss.

B - 1) Unit self recovers without user intervention.

2) No data loss.

C - 1) Upset OK provided that unit will function after user intervention.

Momentus 5400.2 PATA Product Manual, Rev. B

2.13

Reliability

Measurement type

Specification

Nonrecoverable read errors

Annualized Failure Rate (AFR)

Load/Unload (U/UL)

1 per 10 bits read, max.

0.73%

25°C, 50% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

32°C, 80% relative humidity

5°C, 80% relative humidity

5°C, 10% relative humidity

55°C, 16% relative humidity

600,000 software-controlled power on/off cycles

20,000 hard power on/off cycles

Service Life

Warranty

5 years

5 years on distribution units.

To determine the warranty for a specific drive, use a web browser to access the fol-

lowing web page:

www.seagate.com/support/service/

From this page, click on the “Verify Your Warranty” link. You will be asked to pro-

vide the drive serial number, model number (or part number) and country of pur-

chase. The system will display the warranty information for your drive.

2.14

Agency certification

2.14.1

Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections

of IEC950 and EN 60950 as tested by TUV North America.

2.14.2

Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-

tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product

standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and

the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous

paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply

with the directives when used in the test systems, we cannot guarantee that all systems will comply with the

directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O

cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators

should confirm EMC compliance and provide CE marking for their products.

Momentus 5400.2 PATA Product Manual, Rev. B

Korean RRL

If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-

graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic

Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information

and Communication Republic of Korea.

These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-

ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-

nized lab.

• EUT name (model numbers): ST9120821A. ST9100824A, ST98823A, ST96812A, ST94813A and ST93811A.

• Certificate numbers:

ST9120821A

ST9100824A

ST98823A

ST96812A

ST94813A

ST93811A

E-D011-04-3510(B)

E-D011-04-3506(B)

E-D011-04-3503(B)

E-D011-04-3502(B)

E-D011-04-3504(B)

(pending)

• Trade name or applicant: Seagate Technology International

• Manufacturing date: June 2005

• Manufacturer/nationality: Seagate Technology International

Australian C-Tick (N176)

If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548

1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-

cation Authority (ACA).

2.14.3

FCC verification

These drives are intended to be contained solely within a personal computer or similar enclosure (not attached

as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-

keted to the customer. As a subassembly, no Federal Communications Commission verification or certification

of the device is required.

Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total

assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B

computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is

likely to result in interference to radio and television reception.

Radio and television interference. This equipment generates and uses radio frequency energy and if not

installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception.

This equipment is designed to provide reasonable protection against such interference in a residential installa-

tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television, which can be determined by turning the equipment on and off,

you are encouraged to try one or more of the following corrective measures:

• Reorient the receiving antenna.

• Move the device to one side or the other of the radio or TV.

• Move the device farther away from the radio or TV.

• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.

Momentus 5400.2 PATA Product Manual, Rev. B

If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-

gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:

How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-

intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-

ber 004-000-00345-4.

2.15

Environmental protection

Seagate designs its products to meet environmental protection requirements worldwide, including regulations

restricting certain chemical substances.

European Union Restriction of Hazardous Substances (RoHS)

A new law, the European Union Restriction of Hazardous Substances (RoHS) directive, will restrict the pres-

ence of chemical substances, including Lead (Pb), in electronic products effective July 2006. The directive's

requirements have not been finalized. This drive is manufactured with components and materials that are

expected to comply with the RoHS directive when the directive takes effect.

2.16

Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to

light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM

B845. However, this accelerated testing cannot duplicate every potential application environment. Users

should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive

chemicals as electronic drive component reliability can be affected by the installation environment. The silver,

copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-

ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components

should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-

nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any

electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.

Momentus 5400.2 PATA Product Manual, Rev. B

3.0

Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1

Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-

charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s

exposure to ESD.

• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal

chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire

installation procedure.

• Handle the drive only by its edges or frame.

• The drive is fragile—handle it with care. Do not press down on the drive top cover.

• Always rest the drive on a padded, antistatic surface until you mount it in the computer.

• Do not touch the connector pins or the printed circuit board.

• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids

the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are

used to seal out dirt and contamination.

Momentus 5400.2 PATA Product Manual, Rev. B

3.2

Jumper settings

3.2.1

Master/slave configuration

Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the

4-pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable

select option, see Section 3.2.2.

The “Master or single drive” option is the factory default setting.

Drive is master (or single drive)

Drive is slave

Cable select

Figure 3. Jumper settings

3.2.2

Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28,

CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To

enable cable select, set a jumper as shown in Figure 3. Refer to your computer manual to determine whether

your computer supports this option.

Momentus 5400.2 PATA Product Manual, Rev. B

3.3

Drive mounting

You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting

holes. See Figure 4 for drive mounting dimensions (dimensions in inches with mm in parentheses). Follow

these important mounting precautions when mounting the drive:

• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.

• Use only M3 x 0.5 mounting screws.

• Do not overtighten the mounting screws (maximum torque: 4.0 inch-lb).

• Four (4) threads (0.080 inches) minimum screw engagement recommended.

Measurements shown in Figure 4 are in inches.

DIMENSIONS PER EIA-720 OR SFF 8201 SPECIFICATION.

DIMENSIONS PER SFF 8212 OR SFF 8223.

DRIVE LENGTH W/ PATA IS 3.945 .057 (WORST CASE).

DRIVE LENGTH W/ SATA IS 3.957 .062 (WORST CASE).

3.945

.010

(BASE)

( .490

.217

)

.050

.157

.399

( .673

)

OF CONN.

DATUM B

OF DRIVE

2.750

.010

(BASE)

( .189

)

SATA

PATA

3.567

.551

2X M3 X 0.5-6H

.020

)

(

MOUNTING HOLES; BOTH SIDES

.12 MIN FULL THREAD

0.148 .010 X 90

.374

-D-

.008

SECTION B-B (SATA)

2X .118

BOTH SIDES

.039

4X M3 X 0.5-6H

3.567

(BASE)

MOUNTING HOLES; BOTH SIDES

.10 MIN FULL THREAD

0.148 .010 X 90

.551

.152

.399

DETAIL A (PATA)

2.430

.039

.016

-B-

.012

.370

.160

DETAIL A

-C-

DETAIL A (SATA)

Figure 4. Mounting dimensions—top, side and end view

Momentus 5400.2 PATA Product Manual, Rev. B

4.0

ATA interface

These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports

ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The

drive also supports the use of the IORDY signal to provide reliable high-speed data transfers.

For detailed information about the ATA interface, refer to the draft of AT Attachment with Packet Interface

Extension (ATA/ATAPI-6), NCITS T13 1410D, subsequently referred to as the Draft ATA-6 Standard.

4.1

ATA interface signals and connector pins

The following table summarizes the signals on the 44-pin ATA interface connector. For a detailed description of

these signals, refer to the Draft ATA-6 Standard.

Table 6:

Connector signals

Connector

Contact

Cable

Conductor

Cable

Conductor

Connector

Contact

Signal Name

RESET-

DD7

Ground

DD8

DD6

DD9

DD5

DD10

DD4

DD11

DD3

DD12

DD2

DD13

DD1

DD14

DD0

DD15

Ground

DMARQ

DIOW-

DIOR-

IORDY

DMACK-

INTRQ

DA1

(keypin)

Ground

PSYNC:CSEL

Ground

IOCS16-

PDIAG-

DA2

DA0

CS1FX-

DASP-

+5 V (Logic)

CS3FX-

Ground

+5V (Motor)

No connection

Ground (Return)

Momentus 5400.2 PATA Product Manual, Rev. B

4.1.1

Supported ATA commands

The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA

commands, refer to the Draft ATA-6 Standard...

Table 7:

Supported commands

Command name

Command code (in hex)

ATA-standard commands

ATA Device Configuration Overlay

ATA Service

Check Power Mode

Download Microcode

Execute Device Diagnostics

Flush Cache

98 E5

Flush Cache Extended

Format Track (Legacy)

Identify Device

Idle

97 E3

Idle Immediate

95 E1

Initialize Device Parameters

Read Buffer

Read DMA

C8 C9

Read DMA Extended

Read Log Extended

Read Multiple

Read Multiple Extended

Read Native Max Address

Read Native Max Address Extended

Read Sectors

20 21

Read Sectors Extended

Read Verify Sectors

Read Verify Sectors Extended

Recalibrate

40 41

Security Disable Password

Security Erase Prepare

Security Erase Unit

Security Freeze Lock

Security Set Password

Momentus 5400.2 PATA Product Manual, Rev. B

Table 7:

Supported commands

Command name

Security Unlock

Seek

Command code (in hex)

Set Drive Parameters

Set Features

Set Max Address

Note: Individual Set Max com-

Address

mands are identified by the value Password

placed in the Set Max Features

Lock

Unlock

Freeze Lock 04

Set Multiple Mode

Sleep

99 E6

S.M.A.R.T.

Standby

96 E2

H, H

Standby Immediate

Vendor Unique

Write Buffer

94 E0

H, H

9A FA FB

Write DMA

CA CB

H, H

Write DMA Extended

Write Log Extended

Write Multiple

Write Multiple Extended

Write Sectors

30 31

Write Sectors Extended

ATA-standard power-management commands

Check Power Mode

Idle

98 or E5

97 or E3

Idle Immediate

95 or E1

Sleep

99 or E6

Standby

96 or E2

Standby Immediate

ATA-standard security commands

Security Set Password

Security Unlock

Security Erase Prepare

Security Erase Unit

94 or E0

Momentus 5400.2 PATA Product Manual, Rev. B

Table 7:

Supported commands

Command name

Command code (in hex)

Security Freeze Lock

Security Disable Password

Momentus 5400.2 PATA Product Manual, Rev. B

4.1.2

Identify Device command

The Identify Device command (command code EC ) transfers information about the drive to the host following

power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 7 on

page 22. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or

vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.

Thefollowingcommandscontaindrive-specificfeaturesthatmaynotbeincludedintheDraftATA-6Standard.

Word

Description

Value

0C5A

Configuration information:

• Bit 15: 0 = ATA; 1 = ATAPI

• Bit 7: removable media

• Bit 6: removable controller

• Bit 0: reserved

Number of logical cylinders

16,383

ATA-reserved

0000

Number of logical heads

Retired

0000

Retired

0000

Number of logical sectors per logical track: 63

Retired

003F

7–9

10–19

0000

Serial number: (20 ASCII characters, 0000 = none)

ASCII

Retired

Obsolete

0000

0400

0000

x.xx

23–26

Firmware revision

(8 ASCII character string, padded with blanks to end of string)

27–46

Drive model number (40 ASCII characters, padded with blanks

to end of string)

ST9120821A

ST9100824A

ST98823A

ST96812A

ST94813A

ST93811A

(Bits 7–0) Maximum sectors per interrupt on Read multiple and

Write multiple (16)

8010

Reserved

0000

Standard Standby timer, IORDY supported and may be disabled

ATA-reserved

2F00

0000

0200

0007

PIO data-transfer cycle timing mode

Retired

Words 54–58, 64–70 and 88 are valid

Number of current logical cylinders

Number of current logical heads

Number of current logical sectors per logical track

xxxx

Momentus 5400.2 PATA Product Manual, Rev. B

Word

57–58

Description

Value

Current capacity in sectors

xxxx

Number of sectors transferred during a Read Multiple or Write

Multiple command

60–61

Total number of user-addressable LBA sectors available

(see Section 2.2 for related information)

ST9120821A = 234,441,648

ST9100824A = 195,371,568

ST98823A = 156,301,488

ST96812A = 117,210,240

ST94813A = 78,140,160

ST93811A = 58,605,120

Retired

0000

Multiword DMA active and modes supported (see note following

this table)

xx07

Advanced PIO modes supported (modes 3 and 4 supported)

0003

0078

Minimum multiword DMA transfer cycle time per word (120

nsec)

Recommended multiword DMA transfer cycle time per word

(120 nsec)

0078

Minimum PIO cycle time without IORDY flow control (240 nsec)

Minimum PIO cycle time with IORDY flow control (120 nsec)

ATA-reserved

00F0

0078

0000

69–74

Queue depth

76–79

ATA-reserved

Major version number

007E

Minor version number

0000

Command sets supported

346B

Command sets supported

7D01

Command sets support extension

Command sets enabled

4003

34xx

Command sets enabled

3xxx

Command sets enable extension

4003

Ultra DMA support and current mode

(see note following this table)

xx3F

Security erase time

0000

0040

Enhanced security erase time

Advanced power management value

Master password revision code

Hardware reset value (see description following this table)

Auto acoustic management setting

ATA-reserved

FFFE

xxxx

95–127

128

0000

0001

Security status

Momentus 5400.2 PATA Product Manual, Rev. B

Word

Description

Value

xxxx

129–159

160–254

255

Seagate-reserved

ATA-reserved

Integrity word

0000

xxA5

Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data.

Description (if bit is set to 1)

Bit

Word 63

Multiword DMA mode 0 is supported.

Multiword DMA mode 1 is supported.

Multiword DMA mode 2 is supported.

Multiword DMA mode 0 is currently active.

Multiword DMA mode 1 is currently active.

Multiword DMA mode 2 is currently active.

Bit

Word 88

Ultra DMA mode 0 is supported.

Ultra DMA mode 1 is supported.

Ultra DMA mode 2 is supported.

Ultra DMA mode 3 is supported.

Ultra DMA mode 4 is supported.

Ultra DMA mode 0 is currently active.

Ultra DMA mode 1 is currently active.

Ultra DMA mode 2 is currently active.

Ultra DMA mode 3 is currently active.

Ultra DMA mode 4 is currently active.

Ultra DMA mode 5 is currently active.

Bit

Word 93

1 = 80-conductor cable detected, CBLID above VIH

0 = 40-conductor cable detected, CBLID below VIL

Momentus 5400.2 PATA Product Manual, Rev. B

4.1.3

Set Features command

This command controls the implementation of various features that the drive supports. When the drive receives

this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-

rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.

Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the

Features register are defined as follows:

Table 8:

Features register values

Enable write cache (default).

Set transfer mode (based on value in Sector Count register).

Sector Count register values:

Set PIO mode to default (PIO mode 2).

Set PIO mode to default and disable IORDY (PIO mode 2).

PIO mode 0

PIO mode 1

PIO mode 2

PIO mode 3

PIO mode 4 (default)

Multiword DMA mode 0

Multiword DMA mode 1

Multiword DMA mode 2

Ultra DMA mode 0

Ultra DMA mode 1

Ultra DMA mode 2

Ultra DMA mode 3

Ultra DMA mode 4

Ultra DMA mode 5

Enable advanced power management

Disable read look-ahead (read cache) feature.

Disable write cache.

Enable read look-ahead (read cache) feature (default).

Report full capacity available

Note. At power-on or after a hardware or software reset the default values of the features are as indicated

above.

Momentus 5400.2 PATA Product Manual, Rev. B

5.0

Compatibility summary

5.1

Installation considerations

Many of today’s mobile computers have been designed to make it possible for the end user to replace the hard

drive. Refer to your system’s user manual for the location of the hard drive compartment and the specific

instructions regarding replacement. Refer to your system manufacturer’s support website for the most up-to-

date information. Read and follow all instructions regarding the proper steps to be taken when replacing the

system hard drive. Some mobile systems are sealed and require specialized tools to gain access to the hard

drive. Special training or tools may be needed to service some mobile computers. In some cases, opening the

case may void your warranty. Consult your system documentation. Seagate recommends taking your system

to an authorized service technician to replace your hard drive.

Momentus 5400.2 PATA Product Manual, Rev. B

System Compatibility

Seagate Product Assurance has tested Momentus drives in the systems listed in Table 9. Testing included mul-

tiple BIOS versions and operating systems. This testing was done to demonstrate compatibility with various

hardware and software configurations. Hardware and software combinations, other than those tested, may

also be compatible with this drive.

Table 9:

Tested systems

Gateway 300SE

Gateway 450RGH

Gateway 500XL

Gateway 700S

Gateway 700X

ABIT BL7

Acer Aspire 2000

Amilio

ASUS P4SGL-VM

AZZA P4X2-AV

Bonatti

EVO D300

EVO D300V

EVO D310

EVO D310M

EVO D310V

EVO D500

EVO D500M

EVO D500S

Lavie LJ700/7E

Lavie LL750/8

Lavie LL970/9D

Lavie LR700/9E

Lavie LS830/9D

Microstar MSI-6561

Microstar MSI-6566E

Millennia 920I PRO

MIM 2020

Micron T2000

Micron T2100

Micron T2200

Thinkpad

Thinkpad A22E

ThinkpadG40

Thinkpad T30

Thinkpad T40

Tian YI S180

EVO D510

EVO D510 SFF

EVO D510C

MIT-RHE-BT

Netvista

Transport GX3

Transport T1000

Transport V1000

Travel Mate 660

Travel Mate 800LCI

Travel Mate 2500

Travel Mate 290VCI

Travel Mate 650

Travel Mate 660

Travel Mate 800

Travel Mate 8000

Trigem S7 7570

Trigem V7 7600

NECUNI-TRI-NT

Micron V2000

Vaio PCG-V505/B

Vaio PCG-ZIR/P

Vaio PCV RX770

Vaio PCV7753

Vaio PCV-7753

Valuestar VC300/4D

Valuestar VF500/8D

Valuestar VF500/D

Valuestar VG17H/8

Valuestar VG17H2Z38

Valuestar VT500/4D

Veriton 7200D

Brasilia

EVO E-6000

EVO N620C

EVO W-4000

FID 2040

FID 2100

FMV 16C/V

Optiplex GX150

Optiplex GX260

Optiplex GX400

Pavillion 774Y

Pavillion ZD7000

Pavillion ZT3000

Pavillion ZV5000

Pavillion ZX5000

Sony PCV-RZ60

Performance

Client Pro 345

Client Pro 345E

Compaq NX9500

Compaq D315

HP D330

HP D330 MT

HP D330 UT

HP D530

FMV Biblo MG 75HT/ST

FMV Biblo NB75H/T

FMV Biblo NH90H/T

FMV CE50G7 (IVY6)

FMV NB18C

Gigabyte GA-7DXR+

Gigabyte GA-8IDX

Gigabyte GA-8SIML

Gigabyte GA-8SR533

HP/Compaq NX7000

IBM XNote

Imedia 7150(Discovery)

Inspirion 8100

Inspirion 1150

Inspirion 2650

Inspirion 300M

Inspirion 5100

Inspirion 5150

Inspirion 600M

Inspirion 8600

Inspirion 9100

Inspirion XPS

Intel 845GBV

Intel SPRINGDALE-G

Intellistation EPVO

Intellistation M PRO

JIA HE H150

Latitude 100L

Latitude 8600

Latitude D400

Latitude D505

Latitude D600

Latitude D800

Latitude X300

HP D530 CMT

HP D530 SFF

HP D530 USDT

Dimensio GX400

Dimension 4100

Dimension 4100 XPSZ

Dimension 4400

Dimension 4500S

Dimension 4600

Dimension 8100

Dimension 8200

Dimension 8250

Dimension 8300

Dimension XPS

Dynabook TX/2513CMCW

Compaq E -6000

Gateway E Series

Gateway E-2000

Gateway E-4000

Gateway E-4100

Gateway E4600

Gateway E6000

Gateway E-6100

Elite ECS-K7S6A

Elite ECS-L4S5MG

Elite K7S5A

Performance 1400

Performance 1500

Powerbook 5

Powerbook 5,2

Powerbook G4

Precision 330

Precision 340

Precision 350

Precision 360

Precision 530

Precision M60

Presario 2100

Presario 2500

Presario 6000

Presario 8000

Presario 8000Z

Presario R3000

Presario X1000

Pro S P4-1300SE

Pro S P4-1400

Qosmio E10/1JCDT

IBM R50

Veriton 7500

VGN-A70P

W 6000

Workstation XW5000

Workstation XW8000

Presario X1000

MPC X3000

IBM R50P

SB-4100A

SB-4100-C

SB-4100-E

SB-4100-B

Shuttle AV40

Slotek SL-85SD

Scnic

Yi He A760D

Zhao Yang E260

Zhao Yang E600A

Zhao Yang S620

Equium 3140CS

Equium 3150

Equium 5070CS

ES2 300X

ES2 500S

ESX- SB-400 E PC

ESX500S

Momentus 5400.2 PATA Product Manual, Rev. B

5.2

BIOS versions tested

The following list indicates the types of BIOS Seagate tested during the compatibility testing process. The list

highlights the major BIOS manufacturers. Individual systems contain variations of these BIOS versions and

were tested with regard to their implementation in the individual systems.

Table 10:

Tested BIOS versions

Release

Vendor

ACER

ACPI

Revision

1.01

Ver. 1.20

Various

AMI

Various

4.71F1

4.8.4F1

Various

38118

68xxx

Apple

Award

Compal

Compaq

Dell

Various

v2.00

Various

v1.08

78xxx

8602

F.07

Various

A03

Gateway

Various

1.1

IBM

Insyde SCU

Insyde

Intel

Various

Mobilepro

786B2

Various

v1.11

M1300

Medion

Micron

Mobile Pro

NEC

A02

37763

1.0D-1373-0812

Various

4.00.01

Various

V1.04 EC1.01M

Various

Phoenix

Toshiba

Various

Momentus 5400.2 PATA Product Manual, Rev. B

5.3

Operating system versions tested

This list indicates the types of Operating Systems Seagate tested during the compatibility testing process and

highlights the major OS manufacturers. Several variations of the major operating systems have been tested.

Table 11:

Operating systems tested

Manufacturer

Apple

Version/Release

MacOS 9.22

Apple

MacOS X 10.2.3

Microsoft

MSDOS 6.22

Windows 98, 98SE, ME (multiple languages)

Windows 2000, 2000-Pro (+SP 1 thru 4) (multiple languages)

Windows NT 4.0 (+SP 6 and 6a) (+Japanese)

Windows XP, XP Pro, XP Home (+SP1) (multiple languages)

5.4

Compatibility test configurations

The Momentus drives have been tested to demonstrate compliance with ATA/ATAPI-6 in both the master drive

and slave drive positions. These tests were preformed to ensure the functionality to ATA/ATAPI-6 specifications

and the compatibility of Seagate Momentus drives with other ATA/ATAPI-6 compliant peripherals.

5.5

Software utilities

The following is a brief overview of a some of the Seagate utilities used during the Seagate competitive analy-

sis process.

The Seagate SeaTools application is an exclusive disc drive diagnostic software designed to troubleshoot most

hard drive issues. Desktop edition works with most ATA, SATA, or SCSI drives in desktop systems and has a

98 percent accuracy rate.

The Seagate DiscWizard™ application simplifies the installation of disc drives. This software also overcomes

many system BIOS and operating system limitations that can complicate the installation of higher-capacity ATA

(IDE) interface drives.

This is a list of some of the third party utilities used in the testing process.

Vendor

AMI

Application

Diagnostic

Apple

Macbench

Intel

PCI-EXE

Microsoft

Symantec

Winbench99

Norton Utilities

5.6

Other certification

Microsoft software compatibility.

Momentus 5400.2 PATA Product Manual, Rev. B

6.0

Seagate Technology support services

Online services

Internet

www.seagate.com for information about Seagate products and services. Worldwide support is available 24

hours daily by e-mail for your questions.

Presales Support: www.seagate.com/support/email/email_presales.html or [email protected]

Technical Support: www.seagate.com/support/email/email_disc_support.html or [email protected]

mySeagate

my.seagate.com is the industry’s first Web portal designed specifically for OEMs and distributors. It provides

self-service access to critical applications, personalized content and the tools that allow our partners to man-

age their Seagate account functions. Submit pricing requests, orders and returns through a single, password-

protected Web interface—anytime, anywhere in the world.

reseller.seagate.com

reseller.seagate.com supports Seagate resellers with product information, program benefits and sales tools.

You may register for customized communications that are not available on the web. These communications

contain product launch, EOL, pricing, promotions and other channel-related information. To learn more about

the benefits or to register, go to reseller.seagate.com, any time, from anywhere in the world.

Automated phone services

SeaFONE (1-800-SEAGATE) is the Seagate toll-free number (1-800-732-4283) to access our automated

directory assistance for Seagate Service Center support options. International callers can reach this service by

dialing +1-405-324-4770.

Seagate Service Centers

Presales Support

Our Presales Support staff can help you determine which Seagate products are best suited for your specific

application or computer system, as well as drive availability and compatibility.

Technical Support

If you need help installing your drive, consult your system's documentation or contact the dealer's support ser-

vices department for assistance specific to your system. Seagate technical support is also available to assist

you online at support.seagate.com or through one of our call centers. Have your system configuration informa-

tion and your drive’s “ST” model number available.

SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or

comments 24 hours daily and exchange messages with a technical support specialist during normal business

hours for the call center in your region.

Momentus 5400.2 PATA Product Manual, Rev. B

Customer Service Operations

Warranty Service

Seagate offers worldwide customer support for Seagate drives. Seagate distributors, OEMs and other direct

customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-

related issues. Resellers or end users of drive products should contact their place of purchase or one of the

Seagate CSO warranty centers for assistance. Have your drive’s “ST” model number and serial number avail-

able.

Data Recovery Services

Seagate offers data recovery services for all formats and all brands of storage media. Our Data Recovery Ser-

vices labs are currently located in North America. To get a free quick quote or speak with a case management

representative, call 1-800-475-0143. Additional information, including an online request form and data loss pre-

vention resources, is available at www.datarecovery.seagate.com.

Authorized Service Centers

In some locations outside the US, you can contact an Authorized Service Center for service.

USA/Canada/Latin America support services

Seagate Service Centers

Presales Support

Call center

Toll-free

Direct dial

FAX

+1-405-324-4704

Americas

1-877-271-3285¹

+1-405-324-4730¹

Technical Support

Call center

Americas

Toll-free

Direct dial

FAX

+1-405-324-3339

1-800-SEAGATE²

+1-405-324-4700²

Customer Service Operations

Warranty Service

Call center

Toll-free

Direct dial

—

FAX / E-mail

+1-956-664-4725

USA, Canada, Mexico and

Latin America

1-800-468-3472³

Brazil

Jabil Industrial Do Brasil

—

+55-11-4191-4761

+55-11-4191-5084

[email protected]

LTDA⁴

Data Recovery Services

Call center

Toll-free

Direct dial

FAX

USA, Canada,

and Mexico

1-800-475-01435

+1-905-474-2162

1-800-475-0158

+1-905-474-2459

Hours of operation are 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 6:00 P.M., Monday through Friday (Central time).

Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday (Central time).

Hours of operation are 8:00 A.M. to 5:00 P.M., Monday through Friday (Central time).

Authorized Service Center

Hours of operation are 8:00 A.M. to 8:00 P.M., Monday through Friday, and 9:00 A.M. to 5:00 P.M., Saturday (Eastern time).

Momentus 5400.2 PATA Product Manual, Rev. B

European support services

For presales and technical support in Europe, dial the Seagate Service Center toll-free number for your spe-

cific location. If your location is not listed here, dial our presales and technical support call center at +1-405-

324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Monday through Friday.

The presales and technical support call center is located in Oklahoma City, USA.

For European warranty service, dial the toll-free number for your specific location. If your location is not listed

here, dial our European CSO warranty center at +31-20-316-7222 from 8:30 A.M. to 5:00 P.M. (Central Europe

time) Monday through Friday. The CSO warranty center is located in Amsterdam, The Netherlands.

Seagate Service Centers

Toll-free support numbers

Call center

Austria

Belgium

Denmark

France

Germany

Ireland

Italy

Presales and Technical Support

—

Warranty Service

00 800-47324289

00 800-311 12 38

00 800-47324289

00 800-31 92 91 40

00 800-47324289

00 800-47324283 (00 800-4SEAGATE)

00 800-47324283

00 800-311 12 38

00 800-47324283

00 800-31 92 91 40

00 800-47324283

Netherlands

Norway

Poland

Spain

Sweden

Switzerland

Turkey

United Kingdom

FAX services—All Europe (toll call)

Technical Support

Warranty Service

+1-405-324-3339

+31-20-653-3513

Africa/Middle East support services

For presales and technical support in Africa and the Middle East, dial our presales and technical support call

center at +1-405-324-4714 from 8:00 A.M. to 11:45 A.M. and 1:00 P.M. to 5:00 P.M. (Central Europe time) Mon-

day through Friday. The presales and technical support call center is located in Oklahoma City, USA.

For warranty service in Africa and the Middle East, dial our European CSO warranty center at +31-20-316-

7222 from 8:30 A.M. to 5:00 P.M. (Central Europe time) Monday through Friday, or send a FAX to +31-20-653-

3513. The CSO warranty center is located in Amsterdam, The Netherlands.

Momentus 5400.2 PATA Product Manual, Rev. B

Asia/Pacific support services

For Asia/Pacific presales and technical support, dial the toll-free number for your specific location. The Asia/

Pacific toll-free numbers are available from 6:00 A.M. to 10:45 A.M. and 12:00 P.M. to 6:00 P.M. (Australian East-

ern time) Monday through Friday, except as noted. If your location is not listed here, direct dial one of our tech-

nical support locations.

Warranty service is available from 9:00 A.M. to 6:00 P.M. April through October, and 10:00 A.M. to 7:00 P.M.

November through March (Australian Eastern time) Monday through Friday.

Seagate Service Centers

Call center

Australia

China (Mandarin)

Hong Kong

Toll-free

1800-14-7201

800-810-9668

800-90-0474

Direct dial

—

+86-10-6225-5336

FAX

—

1, 4

—

1, 4

Hong Kong (Cantonese)

001-800-0830-1730

1-600-180-1104

001-803-1-003-2165

0034 800 400 554

007 98 8521 7635

1-800-80-2335

0800-443988

800-1101-150

00-800-0830-1730

001-800-11-0032165

2, 4

India

Indonesia

3, 4

Japan

Korea

3, 4

—

Malaysia

New Zealand

Singapore

Taiwan (Mandarin)

Thailand

+65-6488-7525

—

1, 4

Customer Service Operations

Warranty Service

Call center

Asia/Pacific

Australia

Toll-free

—

1800-12-9277

—

Direct dial

+65-6485-3595

—

FAX

+65-6485-4860

—

India

+91-44-821-6164

+91-44-827-2461

Hours of operation are 8:30 A.M. to 5:30 P.M., Monday through Friday (Australian Western time).

Hours of operation are 9:00 A.M. to 6:00 P.M., Monday through Saturday.

Hours of operation are 9:30 A.M. to 6:30 P.M., Monday through Friday.

Authorized Service Center

Momentus 5400.2 PATA Product Manual, Rev. B

Publication feedback survey

We are interested in your comments and suggestions regarding this publication. Please take a few minutes to

participate in our survey at the following URL:

http://survey.seagate.com/survey/techpubs.nsf

Thank you for your time and comments.

Momentus 5400.2 PATA Product Manual, Rev. B

Index

Data Defense 1

data-transfer rates 1

DC power 8

demonstrate compliance 32

density 6

Numerics

3D Defense System 1

Diagnostic Defense 1

diagnostic software 1

discs 5

acoustics 13

Active mode 10

AFR 14

dissipation 8

Download Microcode 22

Drive Defense 1

drive diagnostics 7

drive monitoring 1

drive self-test 1

agency certification (regulatory) 14

altitude 11

ambient conditions 3

ambient temperature 7, 11

Annualized Failure Rate 14

areal density 6

ATA interface 21

ATA-standard commands 22

Australian C-Tick 15

autodetection 1

electrical fast transient 13

electromagnetic compatibility 14

Electromagnetic Compatibility Directive 14

electromagnetic immunity 13

electrostatic discharge 13

EMC compliance 14

average seek time 7

EN 60950 14

enclosures 15

BIOS manufacturers 31

BPI 6

Environmental protection 16

environmental specifications 11

error-correction algorithms 1

errors 14

European Union 14

European Union Restriction of Hazardous Substanc-

es 16

buffer 1, 6

burst 1

cable select 1

cable-select option 18

cache 1, 6

case temperature 11

CE mark 14

Execute Device Diagnostics 22

certification 14

FCC verification 15

Features register 28

Flush Cache 22

Flush Cache Extended 22

formatted capacity 5

frequency 13

Check Power Mode 23

chemical substances 16

commands 22

compatibility 30

compatibility summary 29

compatibility test configurations 32

compliance 14

conducted noise 9

conducted RF immunity 13

configuring the drive 17

connector pins 21

Corrosive environment 16

CSA C22.2 (950) 14

CSEL 18

C-Tick 15

current profile 9

cycles 14

guaranteed sectors 5

handling 17

Hazardous Substances 16

heads 1, 5

height 6

humidity 11

Momentus 5400.2 PATA Product Manual, Rev. B

I/O data-transfer rate 6

Identify Device 22

Identify Device command 25

Idle 8, 23

Idle and Standby timers 10

Idle Immediate 23

physical characteristics 6

physical organization 5

pins 21

PIO 21

power consumption 8

power dissipation 8

Idle mode 10

Idle mode power 8

IEC950 14

Information Technology Equipment 14

Initialize Device Parameters 22

interface 6, 21

interface signals 21

interference 15

power frequency h-field immunity 13

power management 10

power on/off cycles 14

power specifications 8

power-management commands 23

power-management modes 10

Power-on to Ready 7

precautions 19

interleave 6

programmable power management 10

internal data-transfer rate OD 6

ISO document 7779 13

radiated RF immunity 13

radio and television interference 15

radio frequency (RF) 13

random track location 8

Read Buffer 22

Read DMA 22

Read DMA Extended 22

read errors 14

Read Multiple 1, 22

Read Multiple Extended 22

Read Native Max Address 22

Read Native Max Address Extended 22

Read Sectors 22

jumper settings 18

Korean RRL 15

LBA mode 5

length 6

Load/Unload 14

logical geometry 5

Read Sectors Extended 22

Read Verify Sectors 22

Read Verify Sectors Extended 22

read/write heads 5

read/write power and current 8

recording and interface technology 6

recording density 6

master/slave 1

Master/slave configuration 18

maximum temperature 11

modes 21

monitoring 1

mounting the drive 17, 19

recording heads 1

recording method 6

relative humidity 11

noise 9

reliability 14

nominal power 3

resistance 9

nonoperating shock 12

nonoperating vibration 12

nonrecoverable read errors 14

RF 13

RoHS 16

S.M.A.R.T. 23

operating shock 12

operating system 30

operating vibration 12

OS manufacturers 32

other certification 32

S.M.A.R.T. drive monitoring 1

safety certification 14

screws 19

SeaTools 1

sectors 5

Momentus 5400.2 PATA Product Manual, Rev. B

security commands 23

Security Disable Password 24

Security Erase Prepare 23

Security Erase Unit 23

Security Freeze Lock 24

Security Set Password 23

Security Unlock 23

Seek 23

vibration 12

voltage 9

voltage dips, interrupts 13

voltage tolerance 9

seek mode 8

Warranty 14

seek time 7

weight 6

Seeking 8

Self refresh, low power 10

Service Life 14

wet bulb temperature 11

width 6

Write Buffer 23

servo electronics 8

Set Features 23

Set Features command 28

Set Max 23

Set Multiple Mode 23

shock 12

Write DMA 23

Write DMA Extended 23

Write Multiple 1, 23

Write Multiple Extended 23

Write Sectors 23

Write Sectors Extended 23

signals 21

single-track seeks 7

Sleep 8, 23

Sleep mode 10

software utilities 32

sound 13

specifications 3

spindle speed 6

Spinup 8

spinup power 8

Standby 8, 23

Standby Immediate 23

Standby mode 8, 10

Standby to Ready 7

static-discharge precautions 17

subassembly 15

support services 33

surge immunity 13

technical support services 33

temperature 11

temperature gradient 11

third party utilities 32

time to ready 7

timers 10

TMR 1

track density 6

track-to-track seek time 7

TUV North America 14

UL 1950 14

Momentus 5400.2 PATA Product Manual, Rev. B

Seagate Technology LLC

920 Disc Drive, Scotts Valley, California 95066-4544, USA

Publication Number: 100367120, Rev. B, Printed in U.S.A.

Texas Instruments TMS320DM648 User Manual
Teac CD WE552G User Manual
Sanyo SCP 5300 User Manual
SanDisk SDUSB 101 1024 User Manual
Samsung SGH d407 User Manual
Rotel Compact Disc Changer RCC 945 User Manual
Research In Motion Blackberry Cell Phone 9550 User Manual
Oregon RMR616HGA User Manual
Nokia E60 User Manual
Nokia 6682 User Manual