Samsung SH D162D User Manual

Warning/Caution  
Introduction  
to the  
Safety Precautions  
The following are basic precautions to ensure user safety  
Connecting the Cables  
DVD-ROM  
Warning: To warn the user that failure to comply with the instructions may result in  
DVD-ROM DRIVE  
SH-D162D(TS-H352D)  
serious injury or death.  
Caution:  
To caution the user that failure to comply with the instructions may result in  
damage to property.  
and reduce the risk of property damage.  
Design and specifications are subject to change without prior notice.  
Eject Button  
Connecting the Cables  
User Guide - ENGLISH  
When you install the drive  
FCC Compliance  
This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against harmful interference in a  
residential installation.  
This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to radio or television reception,  
which can be  
Place the drive on a level  
surface.  
Do not drop the drive, and  
protect it fromsevere shocks.  
Never allow food particles or  
foreign substances to enter the  
drive casing.  
Avoid high-humidity environments.  
Failure to do so may cause the  
device to fall onto a hard surface,  
resulting in damage or malfunction.  
Power cable  
It can damage the drive or cause  
it to malfunction.  
Front  
EIDE cable  
Master/slave select terminal  
Audio cable  
deter-mined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
Disc compartment  
LED  
Emergency eject hole  
While operating  
• Re-orient or relocate the receiving antenna.  
If the compartment does not open  
when you press the Eject button,  
power off the computer, insert a pin  
or unfolded paper clip in the hole  
and push firmlhy)  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet on a circuit different from that to  
Do not move the drive while in operation and  
do not attempt to open the disc tray byforce.  
Make sure to close all working programs before  
attempting to open the tray and always use the  
open/close button.  
If the power cable is not connected  
properly, it may cause a fire or  
damage the drive. Check the direction  
of the power connector and the drive  
incline before connection.  
which the receiver is connected.  
To protect against the risk of  
fire, do ot spill such liquids as  
alcohol and benzene on the  
drive.  
• Consult the dealer or an experienced radio/TV technician for help.  
Avoid low- or high-temperature  
environments.  
Connecting the power cable  
1
2
CAUTION  
The 4-pin power cable from the internal power unit of your computer must  
be connected to the power terminal the rear of the DVD-ROM drive.  
Change or modifications not expressly approved by the manufacturer responsible for  
compliance could void the user ’s authority to operate the equipment.  
LASER STANDARD  
IEC 60825-1 :1993 +A1 :1997 +A2 :2001  
Connecting the EIDE cable  
•Insert the EIDE cable (40-pin), which is connected to the hard  
disk to the interface terminal.  
WEEE  
+5V DC  
Ground  
Ground  
Interface terminal  
Sound output terminal  
+12V DC  
Correct Disposal of This Product (Waste Electrical &Electronic Equipment)  
(Applicable in the European Union and other European countries with separate collection systems)  
Do not insert a pin into the emergency  
opening while in operation.  
(Place the red line of the cable close to the Pin 1.)  
This marking shown on the product or its literature,indicates that it should not be disposed with  
other household wastes at the end of its working life.To prevent possible harm to the  
environment or human health from uncontrolled waste disposal,please separate this from other  
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.  
Installing a jumper on the master/slave select terminal  
Other  
Rear  
3
•Connect  
a
jumper to the rear sideDV  
o
D
f
-RthOeM.  
Do not use cracked, distorted or  
damaged discs.  
Handle with caution to prevent  
damage from external shock.  
If the jumper is connected to MA (Master), it will work in the Master mode.  
If the jumper is connected to SL (Slave), it will work in the Slave mode.  
If the jumper is connected to CS (CSEL), you can control the device by using the  
host interface signal CSEL. (In general, connection to MA is recommended.)  
Do not disassemble, attempt to repair  
or modify the device without express  
approval as directed in the manual.  
Household users should contact either the retailer where they purchased this product,or their  
local government office,for details of where and how they can take this item for environmentally  
safe recycling.  
Do not place the drive in  
direct sunlight.  
Business users should contact their supplier and check the terms and conditions of the purchase  
contract.This product should not be mixed with other commercial wastes for disposal.  
To reduce the risk of damage,  
electric shock, and fire.  
CS : Cable Select(CSEL)  
SL : Slave  
MA: Master  
Digital output Master/slave select terminal  
terminal  
Power terminal  
Samsung Eco-mark  
The Samsung’s own Eco mark helps consumers to easily understand that  
Samsung develops eco-friendly products. This mark represents Samsung’s  
continuous effort to develop eco-friendly products.  
In particular, a disc with a crack on the  
inner tracks may break while in use.  
Accessories  
• RoHS  
(Restriction of the use of certain hazardous substances in electrical and electronic equipment)  
The RoHS, the environment regulation announced by European Union, restricts the use of  
lead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on the  
market in The European Union after July 1, 2006.  
User Guide, Screws.  
Any change or modification not expressly approved by designated qualified personnel could  
void your authority to operate this device.  
1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that  
you make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and it  
will eventually result in irreparable damage to the disc.  
Connecting the EIDE cable from a sound card  
•Connect the 4-pin audio cable between the sound output terminal on the  
DVD-ROM drive and the audio input terminal on the sound card.  
4
Design and specifications are subject to change without prior notice.  
Important to read and understand  
Do not disassemble  
at all times  
2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).  
BG68-01434A Rev.00  
1
3
4
2
Using the Drive/Storing and Cleaning  
Solving Technical Problems  
Technical Specifications  
Installing the Drive  
Your Discs  
The friction noise generated during SPIN-UP and STOP is caused by the  
Automatic Ball Balancing System(ABS) and is not a malfunction.  
When using one EIDE cable  
System Requirements  
Intel Pentium II 350MHz(or higher), 128 MB of RAM (or higher) with an EIDE interface,  
Using the DVD-ROM Drive  
Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear  
of the DVD-ROM drive.  
SH-D162D(TS-H352D)  
SECTIONS  
Windows 2000/XP/Vista / Windows NT 4.0 (or higher)  
CD  
DVD  
Check that the power, audio and EIDE cables are correctly  
connected to the computer.  
Push the power button and boot the computer.  
The DVD-ROM drive is not  
1
CD-DA(Audio), CD-ROM, CD-R, CD-RW, Photo-CD  
detected by the computer.  
(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV,  
CD-TEXT,CD-Plus, DVD-ROM, DVD-VIDEO, DVD+R, DVD-R,  
DVD+RW, DVD-RW, DVD-RAM, DVD+R/-R Dual  
Slave Drive (Choose the SL Jumper)  
Installing the DVD-ROM Drive  
Disc types supported  
Change the EIDE cable and reconnect it to the computer.  
Preferably, connect a second EIDE cable to the DVD-ROM  
drive in master mode.  
DISC  
After booting the computer, open the disc  
2
After installing the DVD-ROM  
drive, the PC gets slower.  
How to install the DVD-ROM drive on your PC. First, remove the cover;  
connect the cable to the DVD-ROM drive and then to the PC.  
compartment by pressing the Eject button.  
Disc diameter  
120mm or 80mm  
Check the position of the jumper in the master/slave select  
terminal.  
Insert the disc (CD) with the label on the disc  
Data transfer rate  
Sustained  
3
facing upwards and close the disc compartment  
The DVD-ROM drive is not  
recognized by MS-DOS.  
Reinstall the device driver or update it with the latest version  
by downloading it from the Samsung Web site.  
Max. 21,600KB/sec(16X)  
16.6MB/sec  
Max. 7,200KB/sec (48X)  
If necessary, attach a horizontal bracket  
MainBoard  
1
Hard Drive  
by pressing the Eject button. The indicator light  
comes on.  
Play the disc (CD).  
PIO mode 4  
to both sides of the drive.  
DMA mode 2  
UDMA mode 2  
16.6MB/sec  
33.3MB/sec  
You can purchase these accessories separately  
from your computer dealer.  
When using two EIDE cable  
The DVD-ROM drive is not  
detected by Windows.  
4
This case may occur when there is a Windows installation  
problem; reinstall Windows.  
Access time(RANDOM) 110ms (typical)  
(Screws for use: M3 X 6 X 4)  
Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear  
of the DVD-ROM drive.  
DRIVE  
PERFORMANCE  
198KB  
Data Buffer capacity  
Playing CD-DA/Audio CDs  
Check whether the CD is of good quality and clean it,  
if necessary.  
A CD is not read or is read  
too slowly.  
Semiconductor laser  
Stepping motor  
Laser  
- If there is only one Optical drive: select MA (Master).  
Run the CD player program supplied with the sound card or play the  
Windows Media Player.  
Slide mechanism  
Master Drive (Choose the MA Jumper)  
Brushless Sensorless DC motor  
Spindle motor  
The disc compartment will  
not open.  
Check that the power cable is correctly connected.  
Playing Video CDs  
Follow the instructions provided with the disc.  
•A video card or MPEG software and  
Load mechanism  
Tray. DC motor (Soft Eject). Horizontal/Vertical.  
Power off and disconnect the PC.  
Insert a pin or unfolded paper clip in the emergency hole and push  
firmly until the disc compartment opens.  
SEC 1  
PRI 1  
ERROR RATE  
10-15  
Mode 1:10-12, Mode 2:10-9  
a
sound card need to be installed to view video CDs.  
Eject, Insert  
Remove the plate from a free expansion slot and install the  
DVD-ROM drive, as shown in the illustration.  
Eject button  
Indicator(LED)  
Required power  
Interface connector  
Audio output  
Jumper block  
Operations  
If the drive is vertically installed, you cannot use an 8 cm Mini Disc  
because the disc is movable.  
2
FRONT PANEL  
REAR PANEL  
BUSY  
When the MPEG software  
plays a Video CD, the pictures  
are not regular and the running  
speed is too slow.  
Adjust the size of the replay screen.  
1.5A (rms)  
After checking the display resolution, adjust it, if necessary.  
If you have no free expansion slot, install the drive in place of the  
diskette drive.  
MainBoard  
Hard Drive  
Storing Your Discs  
ATAPI  
-If there is two Optical drive, select MA (Master) / SL (Slave).  
Make sure to use the standardized screws supplied (M3X6).  
Line out 0.7V 20% : 47kΩ  
Do not place a disc in direct sunlight.  
Store a disc vertically in a well-ventilated and  
stable location.  
Master Drive (Choose the MA Jumper)  
Slave Drive (Choose the SL Jumper)  
- To use screws other than M3X6 may result in malfunction.  
Molex 70203 or other compatible models  
Temperature: 5~45°C Humidity: 10~80%  
Temperature: -25~60°C Humidity: 10~90%  
148.2 (W) x 42 (H) x 170 (D) mm (including bezel)  
740 g  
The Disc is not in message is  
displayed even though a disc  
has been inserted.  
The computer may not recognize the disc if you start playback  
too quickly after inserting the disc.  
OPERATING  
ENVIRONMENT  
Do not write or attach a label on a disc.  
Do not drop a disc or place heavy objects on it.  
Open and close the disc compartment and try again.  
Clean the disc and try again.  
SEC 1  
PRI 1  
Storage  
Dimensions  
Net weight  
GENERAL  
The DVD-ROM drive is not  
detected after it is connected  
to a sound card.  
The interface mode of the sound card is AT-BUS.  
You must therefore connect the DVD-ROM drive to the EIDE  
port on the PC mother board, rather than to the sound card,  
or install an EIDE compatible sound card.  
Cleaning Your Discs  
(Choose the SL Jumper)  
(Choose the MA Jumper)  
MainBoard  
DVD-ROM  
Hard Drive  
Plate  
Drive  
Horizontal  
Bracket  
Do not touch the surface  
of a disc; hold it by the  
edges.  
To clean a disc, polish lightly  
from the inside of the disc to the  
outside with a soft cotton cloth.  
The disc may not function properly if there are fingerprints, foreign substances or  
dust on the disc surface.  
5
7
8
9
6

Timex T100 User Manual
Sony ICFC11IPBLK User Manual
Sony Ericsson T237 User Manual
Sony CDX CA760X User Manual
Seagate ST2000VX000 User Manual
Samsung SGH S300M User Manual
RCA GUIDE PLUS+1 F36685 User Manual
Philips AX 5021 User Manual
Palm Treo 300 User Manual
Olympus Floppydisk Adapter MAFP 1E User Manual