Samsung SGH X497 User Manual

SGH-x497 Series  
P O R T A B L E T r i - B a n d  
T E L E P H O N E  
User Guide  
Please read this manual before operating your  
phone, and keep it for future reference.  
UCEG3_PMilton_101005_F11rev.  
GH68-06772A  
Openwave® is a registered Trademark of Openwave, Inc.  
RSA® is a registered Trademark RSA Security, Inc.  
Disclaimer of Warranties; Exclusion of Liability  
EXCEPT AS SET FORTH IN THE EXPRESS WARRANTY  
CONTAINED ON THE WARRANTY PAGE ENCLOSED WITH  
THEPRODUCT, THEPURCHASERTAKESTHEPRODUCT"AS  
IS", AND SAMSUNG MAKES NO EXPRESS OR IMPLIED  
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT  
TO THE PRODUCT, INCLUDING BUT NOT LIMITED TO THE  
MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS FOR  
ANY PARTICULAR PURPOSE OR USE; THE DESIGN,  
CONDITION OR QUALITY OF THE PRODUCT; THE  
PERFORMANCE OF THE PRODUCT; THE WORKMANSHIP  
OF THE PRODUCT OR THE COMPONENTS CONTAINED  
THEREIN; OR COMPLIANCE OF THE PRODUCT WITH THE  
REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION OR  
CONTRACT PERTAINING THERETO. NOTHING  
CONTAINED IN THE INSTRUCTION MANUAL SHALL BE  
CONSTRUED TO CREATE AN EXPRESS OR IMPLIED  
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT  
TO THEPRODUCT.IN ADDITION,SAMSUNG SHALLNOTBE  
LIABLE FOR ANY DAMAGES OF ANY KIND RESULTING  
FROM THE PURCHASE OR USE OF THE PRODUCT OR  
ARISING FROM THE BREACH OF THE EXPRESS WARRANTY,  
INCLUDING INCIDENTAL, SPECIAL OR CONSEQUENTIAL  
DAMAGES, OR LOSS OF ANTICIPATED PROFITS OR  
BENEFITS.  
Table of Contents  
Table of Contents  
5
6
Table of Contents  
7
Section 1: Getting Started  
Topics Covered  
Activating Your Phone  
Switching On or Off the Phone  
Setting Up Voice Mail  
This section allows you to start using your phone by  
activating your service and setting up your voice mail.  
Section 1: Getting Started  
9
   
Activating Your Phone  
When you subscribe to a cellular network, you are  
provided with a plug-in SIM card loaded with your  
subscription details, such as your PIN, any optional  
services available, and many others.  
Installing the SIM Card  
Important! The plug-in SIM card and its contacts can be easily damaged  
by scratches or bending, so be careful when handling, inserting, or  
removing the card.  
Keep all SIM cards out of reach of small children.  
Ifnecessary,switch offthephoneby holding down the  
key until the power-off image displays.  
Remove the battery. To do so:  
1. Slide the battery lock toward the top of the phone and  
hold it in that position.  
2. Lift the battery away, as shown.  
3. Slide the SIM card into the SIM card socket so that the  
card locks into place. Make sure the gold contacts of the  
card face into the phone.  
10  
       
Activating Your Phone  
Note: When you need to remove the SIM card, slide it, as shown, and take  
it out of the socket.  
4. Place the battery so that the tabs on the end align with  
the slots at the bottom of the phone.  
Section 1: Getting Started  
11  
5. Press the battery down until it clicks into place. Make  
sure that the battery is properly installed before  
switching on the phone.  
Charging a Battery  
Your phone is powered by a rechargeable Li-ion battery.  
A travel adapter comes with your phone for charging the  
battery. Use only approved batteries and chargers. Ask  
your local Samsung dealer for further details.  
You can use the phone while the battery is charging, but  
this causes the phone to charge more slowly.  
Note: You must fully charge the battery before using your phone for the  
first time. A discharged battery recharges fully in approximately  
200 minutes.  
1. With the battery in position on the phone, plug the  
connector of the travel adapter into the jack at the  
bottom of the phone.  
12  
     
Activating Your Phone  
2. Plug the adapter into a standard AC wall outlet.  
3. When charging is finished, unplug the adapter from the  
power outlet and disconnect it from the phone by  
pressing the buttons on both sides of the connector and  
pulling the connector out.  
Note: You must unplug the adapter before you remove the battery from the  
phone during charging; otherwise, the phone could be damaged.  
Low Battery Indicator  
When the battery is weak and only a few minutes of talk  
time remain, a warning tone sounds and the “Warning  
Low Battery” message repeats at regular intervals on the  
Section 1: Getting Started  
13  
 
display. When this happens, your phone turns off the  
backlight to conserve the remaining battery power.  
When the battery level becomes too low, the phone  
automatically turns off.  
Switching On or Off the Phone  
1. Open the phone.  
2. Press and hold the  
key until the phone switches on.  
3. If the phone asks you to enter the phone password, enter  
the password and press the OK soft key or the key.  
Note: Password registration will be done by the user. Users will input the  
first password.  
4. If the phone asks for a PIN, enter the PIN and press the  
OK soft key or the key. For further details, see "PIN  
The phone searches for your network and after finding it,  
the Idle screen appears. Now, you can make or receive  
calls.  
Note: The display language is preset to Automatic at the factory. To change  
the language, use the Language menu. See "Language" on page 101.  
When you wish to switch off the phone, press and hold the  
the power-off image displays.  
key until  
14  
       
Setting Up Your Voice Mail  
Setting Up Your Voice Mail  
All unanswered calls to your phone are automatically  
transferred to your voice mail,even ifyour phone is in use  
or turned off.Therefore,you willwant to set up your voice  
mail and personal greeting as soon as your phone is  
activated.  
To set up your voice mail:  
1. Press and hold  
.
2. Follow the system prompts to:  
Create your pass code  
Record your greeting  
Record your name announcement  
Accessing Your Voice Mail  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Highlight Recent Calls and press the key.  
3. Highlight Voice Mail and press the key.  
4. Highlight Connect to Voice Mail and press the key.  
Your phone dials the specified voice mail number.  
5. When connected, follow the voice prompts to access  
messages.  
To access you voice mail from your keypad, use the  
following steps:  
1. Open the phone to access your keypad.  
2. From an Idle screen, press and hold the  
key.  
3. Follow the voice mail prompts to access messages.  
Section 1: Getting Started  
15  
       
Changing the Voice Mail Number  
Your SIM card gives you default service number of the  
voice mail center. However, you may need to change the  
number. Use the following procedures to change your  
voice mail number.  
1. In Idle mode, press the Menu soft key to access the  
Menu mode.  
2. Highlight Recent Calls and press the key.  
3. Highlight Voice Mail and press the key.  
4. Highlight Voice Server Number and press the key.  
Highlight Voice Server 1 and press the Select soft key  
or the key. The following options appear in the  
display.  
Edit Number: allows you to edit voice mail number.  
Edit Name: allows you to change voice mail number name.  
Delete: deletes voice mail number.  
5. Highlight Edit Number and press the Select soft key or  
key to change the number. Enter new number.  
6. Press the OK soft key to save the update.  
7. Press the  
key to return to Idle mode.  
16  
 
Section 2: Understanding Your Phone  
Topics Covered  
Features of Your Phone  
Open View of Your Phone  
Front View of Your Phone  
Keys  
Understanding the Display Screen  
This section outlines some key features of your phone. It  
also displays the screen and the icons that are displayed  
when the phone is in use.  
Section 2: Understanding Your Phone  
17  
   
Features of Your Phone  
Your phone is lightweight, easy-to-use and offers many  
significant features. The following list outlines a few of  
the features included in your phone.  
User friendly,menu driven access to features and options.  
Instant Messaging capability  
Multimedia capability  
Personal Assistant feature provides calendar, to-do list, alarms,  
calculator, and a unit converter.  
Open View of Your Phone  
The following illustrations show the main elements of  
your phone:  
18  
     
Front View of Your Phone  
Front View of Your Phone  
Keys  
The following list correlates to with the open and closed  
view illustrations.  
1.  
2.  
The headset jack is used for the hands-free headset.  
Performs the functions indicated by the screen text on  
the bottom line of the display.  
3. Makes or answers a call.  
In Idle mode, recalls the last number dialed or received  
when held down.  
In Menu mode, selects a menu function or stores  
information that you have entered, such as a name in  
the phone or SIM memory.  
4. During a call, adjusts the earpiece volume.  
With the phone closed, you can set up or cancel "Silent  
mode" by holding down the volume key, located on the  
left side of the phone.  
5. Enters numbers, letters, and some special characters.  
Section 2: Understanding Your Phone  
19  
     
6. Enters the asterick [*] character for calling features. In  
text entry mode, press to change the character input  
type.  
7. This connector is used to plug in the charging  
accessories.  
8. The microphone used during phone calls and voice  
memo recordings.  
9. Enters the pound [#] character for calling features. In text  
entry mode, press to enter a space.  
10. Deletes characters from the display.  
In Menu mode, returns you to the previous menu level.  
When you hold down  
key, you can access New  
memo in Organize menu directly.  
11. Ends a call. Also switches the phone on and off when  
held down.  
In Menu mode, cancels your input and returns the phone  
to Idle mode.  
12. In Idle mode, launches the WAP (Wireless Application  
Protocol) browser.  
In Menu mode, selects the highlighted menu options.  
13. In Menu mode, use to scroll through the menus and  
Phone book.  
In Idle mode, the Down key allows you to access the  
Address Book menu directly.  
When entering text, moves the cursor to the left or right,  
depending on which side you push.  
14. Display area where text and graphics are displayed.  
20  
Understanding the Display Screen  
15. The earpiece is used to listen to audio from your phone.  
16. The antenna is used to obtain reception.  
17. The external display shows the received signal strength,  
the phone battery level, the date and time.  
Understanding the Display Screen  
The display has 3 areas:  
Icons  
Shows the received signal strength. The greater the  
number of bars, the stronger the signal.  
Appears when a new text message has been received.  
Appears when a new voice mail has been received.  
Appears when a new multimedia message has been  
received  
.
Appears when you set an alarm to ring at a specified time.  
For details, see page "Alarms" on page 126.  
Appears when you are out of your service area.  
Appears when a call is in progress.  
Section 2: Understanding Your Phone  
21  
   
Appears when you are connected to a WAP service.  
Appears when the Call Forwarding feature is active. For  
Appears when you are connected to the GPRS network.  
Appears when Silent mode is active or you set the phone  
to vibrate when you receive a call.  
Shows the level of your battery. The more bars you see,  
the more power you have remaining.  
Backlight  
A backlight illuminates the display and the keypad.  
When you press any key or open the phone, the backlight  
comes on. It goes off when no keys are pressed within a  
given period of time, depending on the setting in the  
Backlight Time menu. The display turns off after one  
minute to conserve battery power.  
To specify the length oftime the backlight is active, set the  
Back light menu.  
External Display  
Your phone has an external display on the front of the  
phone. It indicates when you have an incoming call or  
message. It also alerts you at a specified time when you  
have set an alarm. The backlight turns on and the  
corresponding icon appears on the external display.  
When you close the phone, the display shows the current  
time on a digital clock.  
22  
   
Section 3: Call Functions  
Topics Covered  
Making a Call  
Adjusting the Call Volume  
Answering a Call  
Call Log  
Recent Calls  
Silent Mode  
Selecting Functions and Options  
Options During a Call  
This section allows you to make or answer a call. It also  
includes the features and functionality associated with  
making or answering a call.  
Section 3: Call Functions  
23  
   
Making a Call  
When the idle screen displays, enter the area code and  
phone number, and press the  
key.  
Note: When you activate the Auto redial option in the Extra settings menu,  
the phone will automatically redial up to 10 times when the person does  
not answer the call or is already on the phone. See page "Extra Settings"  
on page 102 for further details.  
Making an International Call  
1. Press and hold the  
key. The + character appears.  
2. Enter the country code, area code, and phone number  
and press the  
key.  
Correcting the Number  
1. To clear the last digit displayed, press the  
key.  
2. To clear any other digit in the number, press the Left or  
Right key until the cursor is immediately to the right of  
the digit to be cleared. Press the  
3. To clear the whole display, press and hold the  
Ending a Call  
key.  
key.  
When you want to finish your call, briefly press the  
key.  
Redialing the Last Number  
The phone stores the numbers of the calls youve dialed,  
received, or missed if the call recipient or caller is  
identified. See "Caller ID" on page 152 for further details.  
To recall any of these numbers:  
24  
         
Making a Call  
1. If you have typed characters on the display, press the  
key to return to Idle mode.  
2. Press the key to display a list of the most recent  
numbers used in the order you dialed or received them.  
3. Use the Up and Down keys to scroll through the  
numbers until the number you want highlights.  
4. To dial the number, press the  
key.  
Before you dial the number, press the Options soft key  
to display the following options:  
To see details of the number, press the Options soft key and  
select Details. Press the Select soft key or the  
key.  
To call back the number, press the Options soft key and select  
Call back. Press the Select soft key or the  
number is dialed.  
key. The  
To save the number to your phone or SIM, press the Options  
softkey and select Paste. Press the Select soft key or the  
key.  
To send a text or picture message to the number, press the  
Options soft key and select Send Message. Press the Select  
soft key or the  
To delete the number, press the Options soft key and select  
Delete. Press the Select soft key or the key.  
To delete all of the numbers, press the Options soft key and  
key.  
select Delete all. Press the Select soft key or the  
key.  
Making a Call from the Address Book  
You can store phone numbers that you use regularly on  
the SIM card or in the phones memory. These entries are  
collectively called Address book.  
Section 3: Call Functions  
25  
 
Once you have stored a number in the Address Book, you  
can dialit by pressing a few keys.You can also assign your  
most frequently-used numbers to number keys using the  
Speed Dial feature.  
For further details about the Phone book feature, see  
Adjusting the Call Volume  
During a call, if you want to adjust the earpiece volume,  
use the Volume keys on the left side of the phone.  
Press the key to increase the volume level and the key  
to decrease the level.  
Answering a Call  
When somebody calls you, the phone rings and displays  
the incoming call image.  
The callers phone number, or name if stored in Phone  
book, displays.  
1. If necessary, open the phone. Press the  
key or the  
Accept soft key to answer the incoming call.  
If the Anykey answer option in the Extra settings menu  
is activated, you can press any key to answer a call  
except for the  
key and the Reject soft key.  
If the Open to Answer option in the Extra settings  
menu is activated, you can answer the call simply by  
opening the phone.  
26  
       
Call Log  
Note: To reject an incoming call, press and hold the Volume keys on the  
left side of the phone before opening the phone, or press the Reject soft  
key or  
key.  
2. End the call by closing the phone or pressing the  
key.  
Note: You can answer a call while using the Phone book or menu features.  
After ending the call, the phone returns to the function screen you were  
using.  
Call Log  
All made, received and missed calls are listed in the Call  
Log.  
1. To access the Call Log option, press the  
key. A list of  
calls displays.  
2. Press the Options soft key to get Details, Call Back,  
Paste, Send Message, or Delete the calls.  
3. To place a call press the  
key.  
Recent Calls  
In this menu,you can view missed calls,callreceived,and  
calls made.  
Viewing Missed Calls  
When you are unable to answer a call for any reason, you  
can find out who is calling you, ifthis service is available,  
so that you can call the person back.  
The number ofcalls you have missed displays on the idle  
screen immediately after a call is missed.  
Section 3: Call Functions  
27  
         
To view a missed call immediately:  
1. If the phone is closed, open the phone.  
2. Press the Missed soft key.  
The number corresponding to the most recent missed call  
displays, if available.  
3. To scroll through the missed calls, press the Up or Down  
key.  
4. To call the number displayed, press the  
key.  
Viewing Calls Received  
Your phone retains information about the last 20  
incoming calls and stores them in the Calls Received log.  
You can review the Calls Received log for the time and  
date of the call, as well as other information.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Recent Calls and then highlight Calls Received  
and press the Select soft key or the key. Your list of  
Calls Received appear in the display.  
3. Use the Up or Down Navigation key to highlight a call,  
then press the key to details about your call.  
4. Press the Options soft key to display the following  
options:  
Call Back: calls the selected number.  
Paste: saves the number to your phone or SIM.  
Send Message: allows you to send a SMS or Multimedia  
message to the specified number.  
Delete: erases the selected call from the Calls Made log.  
28  
 
Recent Calls  
Delete All: erases the entire Calls Made log.  
5. Use the Up or Down Navigation key to highlight an  
option.  
6. Press the key to perform the option’s function.  
Viewing Calls Made  
Your phoneretainsinformation about thelast 20outgoing  
calls and stores them in the Calls Made log. You can  
review the Calls Made log for the time and date ofthe call,  
as well as other information.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Recent Calls and then highlight Calls Made and  
press the Select soft key or the key. Your list of Calls  
Made appear in the display.  
3. Use the Up or Down Navigation key to highlight a call,  
then press the key to details about your call.  
4. Press the Options soft key to display the following  
options:  
Call Back: calls the selected number.  
Paste: saves the number to your phone or SIM.  
Send Message: allows you to send a SMS or Multimedia  
message to the specified number.  
Delete: erases the selected call from the Calls Made log.  
Delete All: erases the entire Calls Made log.  
5. Use the Up or Down Navigation key to highlight an  
option.  
Section 3: Call Functions  
29  
 
6. Press the key to perform the option’s function.  
Voice Mail  
information.  
Delete All  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Recent Calls and then highlight Delete All and  
press the Select soft key or the key. The following  
selections appear in the display.  
All Calls: deletes all calls.  
Missed Calls: deletes Missed Calls.  
Calls Received: deletes Calls Received.  
Calls Made: deletes Calls Made.  
3. Press the Up or Down Navigation key to highlight the  
Delete option.  
4. Press the Select soft key or the key.  
Note: A check mark displays next to the log(s) to be deleted.  
5. Press the OK soft key.  
6. To confirm deletion, press the Yes soft key or the No key  
to return.  
30  
   
Recent Calls  
Call Time  
Call Time allows you to view the duration of your Last  
Call, Total Made, and Total Received during the life cycle  
of your phone. Call Time is not for billing purposes.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Recent Calls and then highlight Call Time and  
press the Select soft key or the key. The options  
listed appear in the display.  
Last Call: view the duration of your last call.  
Total Made: view the duration of the Calls Made.  
Total Received: view the duration of the total of your Calls  
Received.  
Life time: view the duration of all calls on your phone since  
activation (Life time timers cannot be erased).  
Reset Timers: resets timer.  
Press the number of the option you wish to enter, or use  
the Navigation key to highlight the option and press the  
Select soft key or the key.  
Data Volume  
When using WAP browsing in GPRSmode,Data Volume  
tracks kilobytes.  
Data Call Time  
When using WAP browsing and performing CSD calls,  
Data Call Time tracks your connection time.  
Section 3: Call Functions  
31  
     
Silent Mode  
Silent mode is convenient when you wish to stop the  
phone from making noise, in a theater for example.  
In Idle mode, press and hold the  
key until the “Silent  
Mode Activated” message and the Mute icon (  
)
display.  
To exit and reactivate the previous sound settings, press  
and hold the key again until “Silent Mode  
Deactivated” appears. The Mute icon ( ) no longer  
displays.  
Selecting Functions and Options  
Your phone offers a set of functions that allow you to  
customize it. These functions are arranged in menus and  
sub-menus, accessed using the two soft keys. Each menu  
and sub-menu allows you to view and alter the settings of  
a particular function.  
Soft Keys  
The roles of the soft keys vary depending on the function  
you arecurrently using;thelabelson thebottom lineofthe  
display just above each key indicate their current role.  
32  
         
Selecting Functions and Options  
The following diagram shows the soft key role while in  
idle mode.  
Selecting Options  
To view the various functions and options available and  
to select the one you want:  
1. Press the appropriate soft key.  
2. To select the function displayed or the option highlighted,  
press the Select soft key or the key.  
3. To view the next function or highlight the next option on a  
list, press the Down Navigation key.  
4. To move back to the previous function or option on a list,  
press the Up Navigation key.  
5. To move back up one level in the menu structure, press  
the key.  
6. To exit the menu structure without changing the  
settings, press the  
key.  
Section 3: Call Functions  
33  
In some functions, you may be asked for a password or  
PIN. Enter the code and press the OK soft key or the  
key.  
When you access a list of options, your phone highlights  
the currently active option.If,however,thereare only two  
options, such as On/Off or Enable/Disable, your phone  
highlights the option that is not currently active, so that  
you can select it directly.  
Options During a Call  
Your phone provides a number of control functions that  
you can use during a call.  
Using the Speakerphone  
While on a call, you can use your Speakerphone by  
following these steps:  
1. Press Options soft key.  
2. Highlight Loud Spkr On and press the Select soft key.  
3. To turn the Loud Spkr Off, press Options and select the  
Loud Spkr off and press the Select soft key.  
Putting a Call on Hold  
You can place the current call on hold whenever you  
want. You can make another call while you have a call in  
progress if your network supports this service.  
To place a call on hold, press the Options soft key.  
Highlight Hold and press the Select soft key or the key.  
You can reactivate the call, by pressing the Resume soft  
key.  
34  
     
Options During a Call  
To make a call while you have a call in progress:  
1. Enter the phone number that you wish to dial or look it up  
in the Address Book.  
2. Press the  
key to dial the second call.  
The first call is automatically put on hold.  
Or  
1. Put the current call on hold by pressing the Hold soft  
key.  
2. Make the second call in the normal way.  
When you havean activate calland a callin hold,you may  
switch between the two calls, changing the one on hold to  
activate and placing the other on hold.  
To switch between the two calls, simply press the Swap  
soft key.  
The current call is placed on hold and the call on hold is  
reactivated so that you can continue conversing with that  
person.  
When you want to finish, end each call normally by  
pressing the  
key.  
Switching off the Microphone (Mute)  
You can temporarily switch your phones microphone  
off, so that the other person cannot hear you.  
Example: You wish to say something to person in the room, but do not  
want the person on the phone to hear you.  
To switch the microphone off temporarily:  
1. Press the Mute soft key.  
Section 3: Call Functions  
35  
 
2. The other person can no longer hear you.  
To switch the microphone back on:  
1. Press the Unmute soft key.  
2. The other person can hear you again.  
Muting or Sending Key Tones  
These options allow you to turn the key tones off or on. If  
the Mute keys option is selected, your phone does not  
transmit the DTMF(DualTone Multi-Frequency)tones of  
the keys, which allows you to press keys without hearing  
annoying key tones during a call.  
Note: To communicate with answering machines or computerized  
telephone systems, the Send keys option must be selected.  
Searching for a Number in Address Book During a Call  
You can search for a number in Address Book during a  
call.  
1. Press the Options soft key or the key.  
2. Press the Down key to highlight the Address Book  
option.  
3. Press the Select soft key or the key.  
The Phone book entries are listed.  
4. Enter the name that you wish to find.  
5. If you enter the first few letters of the name, the Phone  
book entries are listed starting with the first entry  
matching your input.  
6. To view the highlighted entry, press the View soft key.  
36  
 
Options During a Call  
For further details about the Phone book feature, see  
Call Waiting  
You can answer an incoming call while you have a call in  
progress, if this service is supported by the network and  
you have set the Call waiting menu to Activate. You are  
notified of an incoming call by a call waiting tone.  
To answer a call while you have a call in progress:  
1. Press the  
key to answer the incoming call. The first  
call is automatically put on hold.  
2. To switch between the two calls, press the Swap soft  
key.  
To end a call on hold, press the Options soft key or the  
key and select the End held call option.  
To end the current call, press the  
key.  
Making a Multi-Party Call  
A multi-party callisa network servicethatallowsup tosix  
people to take part simultaneously in a multi-party or  
conference call.  
For further details about subscribing to this service,  
contact your service provider.  
Setting up a Multi-Party Call  
1. Call the first participant in the normal way.  
2. Call the second participant in the normal way. The first  
call is automatically put on hold.  
Section 3: Call Functions  
37  
   
3. To join the first participant to the multi-party call, press  
the Options soft key or the key and select Join.  
Press the OK soft key or the key.  
4. To add a new person to the multi-party call, call the new  
person in the normal way and then press the Options  
soft key or the key. Select the Join option and press  
the OK soft key or the key.  
You can add incoming callers by answering the call and  
pressing the Options soft key or the key, and selecting  
Join. Repeat as required.  
Having a Private Conversation With One Participant  
1. Press the Options soft key or the key and choose the  
Select one option. Press the OK soft key or the key.  
The list of call participants appears.  
2. Highlight a person by pressing the Up or Down key, and  
press the Select soft key, the  
key, or the key.  
3. When the Split option highlights, press the OK soft key  
or the key.  
Now you can talk privately to that person. The other  
participants can continue to converse with each other.  
4. To return to the multi-party call, press the Options soft  
key or the key and select Conference. Press the OK  
soft key or the key.  
All of the multi-party call participants can now hear each  
other.  
38  
 
Options During a Call  
Dropping One Participant  
1. Press the Options soft key or the key and choose the  
Select one option. Press the OK soft key or the key.  
The list of call participants appears.  
2. Highlight a person by pressing the Up or Down key, and  
press the Select soft key, the key.  
3. Press the Down key to select the Remove option and  
press the OK soft key or the key.  
The call with that participant ends, but you can continue  
to talk to the other participants.  
4. When you want to end the multi-party call, close the  
phone or press the  
key.  
Section 3: Call Functions  
39  
 
40  
Section 4: Menu Navigation  
Topics Covered  
Menu Navigation  
Navigation Key Shortcuts  
In Use Menu Outline  
Menu Outline  
This section explains the menu navigation for your  
phone. It also includes an outline of all the available  
menus associated with your phone.  
Section 4: Menu Navigation  
41  
   
Menu Navigation  
You can tailor the phones range of functions to your  
needs using menus and sub-menus. Menus and sub-  
menus can be accessed by scrolling using the Navigation  
keys or by using the shortcuts.  
There are two way for accessing a menu option.  
Navigating through the list.  
Entering the shortcut number of the menu option.  
Navigating through the List  
1. In Idle mode, press the Menu soft key to access the main  
menus.  
2. Scroll using the Navigation keys to reach a main menu,  
Settings for example. Press the Select soft key or the  
key to select the menu.  
3. You can access them by scrolling using the Up and  
Down Navigation key and pressing the Select soft key or  
the key.  
If the menu that you have selected contains further  
options, repeat this step.  
4. Select an option and press the Select soft key or the  
key to confirm the chosen setting  
Using Shortcuts  
The menu items,such as menus,sub-menus,and options,  
are numbered and can be accessed quickly by using their  
shortcut numbers. For the main menus, you can access  
any one of them by pressing the number keys (1 to 0)  
corresponding to their location on the screen.  
42  
   
Navigation key shortcuts  
Example: Accessing the Language menu.  
1. Press the Menu soft key.  
2. Press the  
3. Press the  
4. Press the  
5. Press the  
key for Settings.  
key for Phone Settings.  
key for Language.  
key for Text Language.  
The languages available display.  
Navigation key shortcuts  
Some applications can be launched by pressing one of the  
four navigation keys (see the illustration) while in the  
standby mode.  
Section 4: Menu Navigation  
43  
 
In Use Menu Outline  
Your phone includes both a standby menu and an In-Use  
Menu. The In-Use Menu applies to when you are in a call.  
1. While in a call press the Options soft key. The following  
options appear in the display:  
Loud Spkr On: turns the speaker phone on.  
Hold: allows you to place a caller on hold.  
New Call: allows you to make or accept another call.  
Address Book: accesses the Contact List.  
Text Message: allows you to send a text message to your caller.  
Mute Keys: allow you to turn the key tones off or on. If the Mute  
keys option is selected, your phone does not transmit the DTMF  
(Dual Tone Multi-Frequency) tones of the keys, which allows  
you to press keys without hearing annoying key tones during a  
call  
Send DTMF: send your phone number as tones (if youre the  
recipient of the call). Send the recipient’s phone number as  
tones (if youre the originator of the call).  
2. Use the Up or Down Navigation keys to highlight an  
option. Press the Select soft key to select the In-Use  
Menu of your choice.  
44  
 
Menu Outline  
Menu Outline  
The following list shows the menu structure and  
indicates the number assigned to each option.  
1. Recent Calls  
1.1 Missed Calls  
1.2 Calls Received  
1.3 Calls Made  
1.4 Voice Mail  
1.4.1 Connect to Voice Mail  
1.4.2 Voice Server Number  
1.5 Delete All  
1.6 Call Time  
1.6.1 Last Call  
1.6.2 Total Made  
1.6.3 Total Received  
1.6.4 Life time  
1.6.5 Reset Timers  
1.7 Data Volume  
1.7.1 Recent Volume  
1.7.2 Total Volume  
1.7.3 Reset Volume  
1.8 Data Call Time  
1.8.1 Recent Time  
1.8.2 Total Time  
Section 4: Menu Navigation  
45  
   
1.8.3 Reset Timers  
2. Messaging  
2.1 IM  
2.2 Text Message  
2.2.1 Create  
2.2.2 Inbox  
2.2.3 Outbox  
2.2.4 Delete All  
2.3 Multimedia Message  
2.3.1 Create  
2.3.2 Inbox  
2.3.3 Outbox  
2.3.4 Draft  
2.3.5 Delete All  
2.4 Browser Messages  
2.4.1 Inbox  
2.4.2 Setting  
2.4.3 Delete All  
2.5 Templates  
2.6 Broadcast Messages*  
2.7 Chat  
2.8 Settings  
2.8.1 Text Message  
2.8.1.1 Service Center  
46  
Menu Outline  
2.8.1.2 Validity Period  
2.8.1.3 Message Type  
2.8.1.4 Reply Path  
2.8.1.5 Delivery Report  
2.8.1.6 Character Support  
2.8.2 Multimedia Message  
2.8.2.1 Send Settings  
2.8.2.1.1 Priority  
2.8.2.1.2 Validity Period  
2.8.2.1.3 Delivery After  
2.8.2.1.4 Delivery Report  
2.8.2.1.5 Read Reply  
2.8.2.2 Receive Settings  
2.8.2.2.1 Msg. Reception  
2.8.2.2.2 Anonymous Reject  
2.8.2.2.3 Ads Reject  
2.8.2.2.4 Report Allowed  
2.8.2.3 Multimedia Message Profiles  
2.8.2.3.1 Current Profile  
2.8.2.3.2 Profile Setting  
2.9 Memory Status  
2.9.1 Text Message  
2.9.2 Multimedia Message  
Section 4: Menu Navigation  
47  
3. Games & Applications  
3.1 Games  
3.1.1 Shop Games  
3.1.2 My Games  
3.1.3 Settings  
3.1.3.1 APN  
3.1.3.2 Login ID  
3.1.3.3 Password  
3.1.3.4 DNS Settings  
3.1.4 Memory Status  
3.2 Alarm  
3.3 Organizer  
3.3.1 New Memo  
3.3.2 Calendar  
3.3.3 To Do List  
3.4 Calculator  
3.5 Record Audio  
3.5.1 Record  
3.5.2 Recorded Audio  
3.5.3 Delete All  
3.5.4 Settings  
3.5.4.1 Recording Time  
3.5.4.2 Volume  
3.5.4.3 Default Name  
48  
Menu Outline  
3.5.5 Memory Status  
3.6 Unit Conversion  
3.6.1 Length  
3.6.2 Weight  
3.6.3 Volume  
3.6.4 Area  
3.6.5 Temperature  
3.7 Timer  
3.8 Stopwatch  
3.9 World Time  
4. MEdia Mall  
4.1 Shop Ringtones  
4.2 Shop Games  
4.3 Shop Graphics  
4.4 Shop Multimedia  
4.5 Shop Applications  
4.6 MEdia Home  
5. MEdia Net  
5.1 MEdia Net Home  
5.2 Favorites  
5.3 Go to URL  
5.4 Browser Profiles  
5.4.1 Current Profile  
5.4.2 Profile Settings  
Section 4: Menu Navigation  
49  
5.5 Clear Cache  
6. IM  
7. My MEdia  
7.1 Graphics  
7.1.1 Shop Graphics  
7.1.2 Downloaded Graphics  
7.2 Audio  
7.2.1 Shop Ringtones  
7.2.2 Downloaded Ringtones  
7.2.3 Record Audio  
7.2.4 Recorded Audio  
7.3 Delete  
7.3.1 Graphics  
7.3.2 Audio  
7.4 Memory Status  
8. Address Book  
8.1 Contact List  
8.2 FDN List  
8.3 New Entry  
8.3.1 Phone  
8.3.2 SIM  
8.3.3 SIM (FDN)  
8.4 Speed Dial  
50  
Menu Outline  
8.5 Copy All to Phone  
8.6 Delete All  
8.7 Own Number *  
8.7.1 Voice Line 1  
8.7.2 Voice Line 2  
8.7.3 Data  
8.7.4 Fax  
8.8 Group Setting  
8.8.1 Family  
8.8.1.1 Ringtone  
8.8.1.2 Edit Name  
8.8.1.3 View Image  
8.8.2 Friends  
8.8.2.1 Ringtone  
8.8.2.2 Edit Name  
8.8.2.3 View Image  
8.8.3 Partnership  
8.8.3.1 Ringtone  
8.8.3.2 Edit Name  
8.8.3.3 View Image  
8.8.4 Office  
8.8.4.1 Ringtone  
8.8.4.2 Edit Name  
8.8.4.3 View Image  
Section 4: Menu Navigation  
51  
8.8.5 Other  
8.8.5.1 Ringtone  
8.8.5.2 Edit Name  
8.8.5.3 View Image  
8.9 Memory Status  
8.0 Service Number  
9. Settings  
9.1 Time & Date  
9.1.1 Set Time  
9.1.2 Set Date  
9.1.3 Time Format  
9.1.4 Auto Update  
9.2 Phone Settings  
9.2.1 Language  
9.2.1.1 Text Language  
9.2.1.2 Input Mode  
9.2.2 Greeting Message  
9.2.3 Extra Settings  
9.3 Display Settings  
9.3.1 Wallpaper  
9.3.1.1 Shop Graphics  
9.3.1.2 Animations  
9.3.1.3 Graphics  
52  
Menu Outline  
9.3.1.4 Text Position  
9.3.1.5 Text Color  
9.3.2 Skin  
9.3.3 Backlight Time  
9.3.4 Brightness Control  
9.3.4.1 Main LCD  
9.3.4.2 External LCD  
9.3.5 Dialing Font Color  
9.4 Sound Settings  
9.4.1 Incoming Calls  
9.4.1.1 Shop Ringtones  
9.4.1.2 Default Ringtones  
9.4.1.3 My Audio  
9.4.1.4 Ring Volume  
9.4.1.5 Alert Type  
9.4.2 Keypad Tone  
9.4.2.1 Default Keypad Tone  
9.4.2.2 Volume  
9.4.3 Message Tone  
9.4.3.1 Text Message  
9.4.3.1.1 Tone  
9.4.3.1.2 Alert Type  
9.4.3.1.3 Repetition  
Section 4: Menu Navigation  
53  
9.4.3.2 Multimedia Message  
9.4.3.2.1 Tone  
9.4.3.2.2 Alert Type  
9.4.3.2.3 Repetition  
9.4.4 Power On/Off  
9.4.5 Silent Mode  
9.4.6 Extra Tone  
9.5 Network Services  
9.5.1 Call Forwarding  
9.5.2 Call Waiting  
9.5.3 Network Selection*  
9.5.4 Caller ID  
9.6 Security  
9.6.1 PIN Check  
9.6.2 Change PIN  
9.6.3 Phone Lock  
9.6.4 Change Password  
9.6.5 Privacy  
9.6.6 SIM Lock  
9.6.7 FDN Mode*  
9.6.8 Change PIN2*  
9.7 Reset Settings  
9.7.1 All  
9.7.2 Phone Settings  
54  
Menu Outline  
9.7.3 Display Settings  
9.7.4 Sound Settings  
* Shows only if supported by your SIM card.  
Section 4: Menu Navigation  
55  
56  
Section 5: Entering Text  
Topics Covered  
Changing the Text Input Mode  
Using T9 Mode  
Using Alphabet Mode  
Keys  
Using Symbols  
Using Numbers  
This section outlines how to select the desired text input  
mode when entering characters into your phone. This  
section also describes how to use the T9 predictive text  
entry system to reduce the amount of key strokes  
associated with entering text.  
Section 5: Entering Text  
57  
     
Changing the Text Entry Mode  
When using your phone,you willoften need to enter text,  
such as when storing a name in the Address Book,  
creating your personal greeting or scheduling events on  
your calendar. You can enter alphanumeric characters by  
using your phones keypad.  
Your phone has the following text input modes:  
ABC mode  
This mode allows you to enter letters by pressing the key  
labeled with the letter you want. Press the key once,  
twice, three, or four times until it displays.  
T9 mode  
This mode allows you to enter words with only one  
keystroke per letter. Each key on the keypad has more  
than one letter; for example, pressing the  
key can  
enter J, K, or L. However, the T9 mode automatically  
compares the series of keystrokes you make with an  
internal linguistic dictionary to determine the most likely  
word, thus requiring far fewer keystrokes than the  
traditional Alphabet mode.  
Symbolic mode  
This mode allows you to enter symbols, such as  
punctuation marks.  
Number mode  
This mode allows you to enter numbers.  
Add Word  
Allows you to add a word to message and to T9.  
58  
         
Changing the Text Entry Mode  
Language Select  
Allows you to change the language being used in T9  
input mode.  
Changing the Text Input Mode  
When you are in a field that allows characters to be  
entered, you will notice the text input mode indicator on  
the display.  
Text input mode  
indicator  
1. To select change the text input mode, press the key.  
2. Highlight the input option, and press the Select soft key  
or the key.  
3. Choose from the following options:  
: ABC mode  
: T9 mode  
Symbolic  
: Number  
Add Word  
Language Select  
Section 5: Entering Text  
59  
 
Using T9 Mode  
T9 is a predictive text input mode that allows you to key  
in any character using single keystrokes. This text input  
mode is based on a built-in dictionary.  
To enter a word in T9 mode:  
1. When you are in T9 mode, start entering a word by  
pressing the  
once for each letter.  
Example: To enter Hello” press  
to  
keys. Press each key only  
H
E
L
L
O
The word that you are typing appears in the display. It  
may change with each key that you press.  
2. Enter the whole word before editing or deleting the  
keystrokes.  
3. When the word displays correctly, go to step 4.  
If the word doesnt display correctly, press the  
or the Up or Down key to display alternative word  
choices for the keys that you have pressed.  
key  
Example: Both Of and Me” have the  
and  
keys. The phone  
displays the most commonly used choice first.  
4. Insert a space by pressing the  
key and start  
entering the next word.  
60  
   
Using Alphabet Mode  
To add a new word into the T9 dictionary:  
1. After pressing the keys corresponding to the word you  
want to add, press the key or the Up or Down key  
to display the alternative words.  
2. When you press the  
key or the Up or Down key at  
the last alternative word, the display shows Add on the  
bottom line. Press the Spell soft key or the key.  
3. If necessary, clear the word using the  
key and  
enter the word you want to add using ABC mode. See  
4. Press the OK soft key or the key.  
The word is added to the T9 dictionary and becomes the  
first word for the associated keypress series.  
Note: This feature may not be available for some languages.  
To enter periods, hyphens, or apostrophes, press the  
T9 mode applies grammar rules to ensure that correct  
punctuation is used.  
key.  
To shift case in T9 mode, use the  
key. There are 3 cases:  
Initial capital, Capital lock, and Lower case.  
You can move the cursor by using the Left and Right keys. To  
delete letters, press the  
to clear the display.  
key. Press and hold the  
key  
Using Alphabet Mode  
To use theAlphabet Mode use the  
your text.  
to  
keysto enter  
1. Press the key labeled with the letter you want:  
Section 5: Entering Text  
61  
     
Once for the first letter  
Twice for the second letter  
Andsoon  
2. Select the other letters in the same way.  
Note: The cursor moves to the right when you press a different key. When  
entering the same letter twice or a different letter on the same key, just  
wait for a few seconds for the cursor to move to the right automatically,  
and then select the next letter.  
Keys  
62  
 
Entering Symbols  
Entering Symbols  
Symbolmodeallowsyou to enter symbolsby pressing the  
key labeled with the letter you want. When in a text  
message screen, press the  
soft key to access the  
Symbol mode. The Symbol screen displays the available  
symbols for each key. Use the Up or Down Navigation  
keys to cycle through all available symbols.  
1. To select a symbol, press the corresponding number  
key.  
2. To display more symbols, press the Up or Down  
Navigation key.  
3. To clear the symbol(s), press the  
key. When the  
input field is empty, this key returns the display to the  
previous mode.  
4. To insert the symbol(s) into your message, press the OK  
soft key or the key.  
Using Numbers  
Number mode allows you to enter numbers by pressing  
the key labeled with the number you want.When in a text  
message screen, press the  
Number mode.  
soft key to access the  
Section 5: Entering Text  
63  
       
64  
Section 6: Understanding Your Address  
Book  
Topics Covered  
Adding a New Address Book Entry  
Finding an Address Book Entry  
Editing an Existing Address Book Entry  
Dialing a Number from the Address Book  
Dialing a Number from the SIM Card  
Speed Dialing  
Copy All to Phone  
Delete All  
OwnNumber  
Group Setting  
Memory Status  
Service Dialing Number  
This section allows you to manage your daily contacts by  
storing their name and number in your Address Book.  
Address Book entries can be sorted by name, entry, or  
group.  
Section 6: Understanding Your Address Book  
65  
   
Adding a New Address Book Entry  
There are two ways to store a number:  
Using the Save soft key or the key in the idle mode  
Using the New Entry option in the Address Book menu  
Storing a Number in Idle Mode  
1. Enter the number you want to store and press the Save  
soft key.  
Note: If you make a mistake while entering a number, correct it using the  
key.  
2. Select a Save To location and press the Select soft key  
or the key.  
The following Save To locations are available:  
Phone: allows you to save contact to your phone  
SIM: allows you to save contact to your SIM  
SIM (FDN): allows you to restrict your outgoing calls to a limited  
set of phone numbers.  
Note: When you change phones, any numbers stored in your SIM card  
memory are automatically available with the new phone, whereas any  
numbers stored in the phone’s memory will need to be re-entered.  
3. Select an icon to identify the category in which the  
number is to be stored. Use the Up or Down Navigation  
key to highlight the type and press the Select soft key or  
the key.  
Mobile: assigns the number entered to the Mobile entry.  
Home: assigns the number entered to the Home entry.  
66  
 
Adding a New Address Book Entry  
Office: assigns the number entered to the Office entry.  
Fax: assigns the number entered to the Fax entry.  
Other: allows you to enter more detailed information for the  
entry.  
4. Enter a name to associate with the number.  
To use the Entry Options press the Right soft key. For  
further details about how to enter characters See  
5. Press OK soft key or the key to store the name and  
number. After storing, the phone displays the phone  
number and name you just stored.  
6. To dial the number, press the  
key.  
7. To return to the idle screen, press the  
.
Storing a Number Using the New Entry Option  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Select New Entry.  
3. Select a Save To location, then press the Select soft  
key or the key.  
Three available categories:  
Phone: allows you to save contact to your phone  
SIM: allows you to save contact to your SIM  
SIM (FDN): allows you to restrict your outgoing calls to a limited  
set of phone numbers.  
Section 6: Understanding Your Address Book  
67  
Note: When you change phones, any numbers stored in your SIM card  
memory are automatically available with the new phone, whereas any  
numbers stored in the phone’s memory will need to be re-entered.  
4. Select an icon to identify the category in which the  
number is to be stored. To select the category, press the  
Up or Down Navigation key and press the Select soft  
key or the key.  
Mobile: assigns the number entered to the Mobile entry.  
Home: assigns the number entered to the Home entry.  
Office: assigns the number entered to the Office entry.  
Fax: assigns the number entered to the Fax entry.  
Other: allows you to enter more detailed information for the  
entry.  
E-Mail: allows you to enter an e-mail address for the  
number entered.  
5. Enter the number and press the Save soft key or the or  
the key.  
6. Enter the contact name and press the OK soft key or the  
key.  
Press the Options soft key to display options menu. For  
7. To return to the Idle screen, press the  
key.  
Storing a Number to the SIM Memory  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
68  
Adding a New Address Book Entry  
2. Scroll to New Entry by pressing the Up or Down  
Navigation key and press the Select soft key or the  
key.  
3. Select SIM and press the Select soft key.  
4. Enter a number you want to store and press the Save  
soft key or the key.  
5. Enter a name and press the OK soft key or the key.  
For further details about how to enter characters, see  
After storing, the phone displays the Address Book entry  
number you just created  
6. Select the SIM memory location, using the alphanumeric  
keypad and press the OK soft key or the key.  
7. Press the Options soft key to display options menu. For  
8. To return to the Idle screen, press the  
key.  
Storing a Number to the SIM (FDN) Memory  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Scroll to New Entry by pressing the Up or Down  
Navigation key and press the Select soft key or the  
key.  
3. Select SIM (FDN) and press the Select soft key.  
4. Enter your PIN2 number and press the OK soft key.  
Section 6: Understanding Your Address Book  
69  
5. Enter a number you want to store and press the Save  
soft key or the key.  
6. Enter a name and press the OK soft key or the key.  
After storing, the phone displays the Address Book entry  
number you just created  
7. Select the SIM memory location, using the alphanumeric  
keypad and press the OK soft key or the key.  
8. Press the Options soft key to display options menu. For  
9. To return to the Idle screen, press the  
key.  
Using Address Book Entry Options  
Whileviewing any AddressBook entry,presstheLeft soft  
key to use the options for the entry.  
The following options are available:  
Edit Number: allows you to edit the number.  
Edit Name: allows you to edit the name.  
Send Message: allows you to send a message to the selected  
number.  
Copy: allows you to copy the number to another location. You  
can select the memory location, either SIM or Phone, and the  
location number.  
Delete Entry: allows you to delete the name and number from  
Address Book. You are asked to confirm that you wish to delete  
the name and number by pressing the Yes soft key.  
70  
 
Finding an Address Book Entry  
Finding an Address Book Entry  
You can store phone numbers and their corresponding  
names in your SIM card or phone. They are physically  
separate but are used as a single entity, called Address  
Book.  
Depending on your SIM card, the maximum number of  
phone numbers the SIM card can store may differ.  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Using the Up or Down Navigation key highlight Contact  
List and press the Select soft key or the key.  
3. Enter the first few letters of the name.  
The Address Book entries are listed, starting with the  
first entry matching your input.  
4. To view the highlighted entry, press the View soft key.  
5. Press the  
key to dial the number, or press the Left  
soft key to access the Address Book entry options.  
Section 6: Understanding Your Address Book  
71  
   
Editing an Existing Address Book Entry  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Using the Navigation key highlight Contact List and  
press the Select soft key or the key.  
3. Using the Up or Down Navigation key select the Contact  
you would like to edit and press the View soft key.  
4. Press the Options soft key to display options menu. For  
Using the Navigation key highlight the Option and press  
the Select soft key.  
5. When your finished editing the Contact, press the OK soft  
key. Your changes are saved and a confirmation  
message appears.  
Dialing a Number from Address Book  
Once you have stored phone numbers in the Address  
Book, you can dial them easily and quickly by using the  
location numbers that were assigned to them in the  
Address Book.  
Note: If you cannot remember a location number, you must go into the  
Contact List in the Address Book menu to search for the entry by name.  
72  
       
Dialing a Number from the SIM Card  
Dialing a Number from the SIM Card  
1. In Idle mode, enter the location number for the phone  
number you want to dial and press the key.  
The list of entries in the SIM card appears, with the  
desired number highlighted.  
2. You can press the Up or Down key to find other numbers  
on the list.  
3. Press the Dial soft key, the  
key, or the key when  
you have selected the number you want.  
Speed Dialing  
Onceyou have stored phonenumbers from your Address  
Book list, you can set up to 8 speed dial entries and then  
dial them easily whenever you want, simply by pressing  
the associated numeric key.  
Setting Up Speed Dial Entries  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Scroll to Speed Dial by pressing the Up or Down  
Navigation key and press the Select soft key or the  
key.  
3. Select the key to which you wish to assign the speed-  
dialing number, from the  
to  
keys., and press  
the Select soft key or the key.  
Note: Memory location 1 is reserved for your Voice mail server number.  
Section 6: Understanding Your Address Book  
73  
       
4. Highlight Edit Number and press the Select soft key or  
the key. Enter a number or press the Names soft key.  
Highlight Contact List and press the Select soft key to  
display entries in the Contact List.  
5. Select an entry from the Contact List and press the  
View soft key or the key.  
6. Press the Select soft key or the key.  
7. Press the OK soft key or the key.  
Editing the Speed Dial List  
You can edit the speed dial list by changing the number  
assignment to a key or deleting all of the entries on the  
speed dial list.  
Changing a Number Assigned to a Key  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
2. Select Speed Dial and select the key you want to  
change.  
3. Using the Up or Down Navigation key highlight Speed  
Dial location you would like to edit and press the Select  
soft key.  
4. Select Edit Number and press the Select soft key. Using  
the alphanumeric keypad edit number and press OK.  
5. When you have finished, press the  
key.  
Deleting Speed Dial Entries  
1. In idle mode press the Menu soft key. Select Address  
Book and press the Select soft key or the key.  
74  
 
Copy All to Phone  
2. Select Speed Dial then select the number assigned key  
you want to delete.  
3. Using the Up or Down Navigation key highlight the  
Speed Dial location to be deleted and press the Select  
soft key.  
4. Using the Up or Down Navigation key highlight Delete  
and press the Select soft key.  
5. Press the Yes soft key to confirm the deletion.  
6. When you have finished, press the  
key.  
Copy All to Phone  
Copy All to Phone copies all information from the SIM  
memory to the phone memory.  
1. When the Idle screen displays, press the Menu soft key.  
Highlight Address Book and press the Select soft key  
or the key.  
2. Select Copy All to Phone and press the Select soft key  
or the key. Press Yes to copy or No to cancel.  
Delete All  
You can delete all your entries from your phones  
memory, your SIM card, or both.  
1. When the Idle screen displays, press the Menu soft key.  
Highlight Address Book and press the Select soft key or  
the key.  
2. Scroll to Delete all by pressing the Up or Down  
Navigation key and press the Select soft key or the  
key.  
Section 6: Understanding Your Address Book  
75  
   
3. To place a check mark by the memory location you want  
to empty.  
All  
SIM  
SIM(FDN)  
Phone  
Press the Select soft key or the key.  
You can remove the check mark by pressing the Select  
soft key or the key.  
4. Press the OK soft key to delete the entries in the selected  
memory location. A confirmation displays. Press Yes to  
confirm deletion or No to cancel.  
5. Enter the phone password and press the OK soft key or  
the key.  
Note: The password registration will be done by the user.  
6. When you are finished, press the  
key or the  
key.  
Own Number  
This function is a memory aid,which you can use to check  
your own phone number if you need to do so.  
You can assign a name to each of your own phone  
numbers registered on your SIM card. You can also edit  
the names and numbers. Any changes made here do not  
in any affect the actual subscriber numbers on your SIM  
card.  
1. When the Idle screen displays, press the Menu soft key.  
76  
   
Group Setting  
Highlight Address Book and press the Select soft key or  
the key.  
2. Select the Own Number option by pressing the Up or  
Down key and press the Select soft key or the key.  
3. Highlight Edit Number and press the Select soft key or  
the key. Enter the phone number you want and press  
the OK soft key or the key.  
4. Highlight Edit Name and press the Select soft key or the  
key. Enter the name and press the OK soft key or the  
key.  
5. Highlight Delete and press the Select soft key or the  
key. Select Yes to confirm deletion or No to cancel.  
Group Setting  
1. When the Idle screen displays, press the Menu soft key.  
Highlight Address Book and press the Select soft key  
or the key.  
2. Scroll to Group Setting by pressing the Up or Down  
Navigation key and press the Select soft key or the  
key.  
3. Scroll through the group list by pressing the Up or Down  
Navigation key.  
4. When the group you want highlights, press the Select  
soft key or the key.  
5. Select each option and change the settings, as required.  
The following options are available:  
Ring tone: allows you to set the ring tone to be used when you  
receive a voice call from a member of that group.  
Section 6: Understanding Your Address Book  
77  
 
Edit Name: allows you to rename the selected group setting.  
View Image: allows you to view the graphic displayed when you  
receive a voice call from a member of that group.  
6. When you are finished, press the  
key or the  
key.  
Memory Status  
Memory Status allows you to check how many Address  
Book entries are saved in your SIM card or internal phone  
memory.  
1. When the Idle screen displays, press the Menu soft key.  
Highlight Address Book and press the Select soft key or  
the key.  
2. Select the Memory status option by pressing the Up or  
Down key and press the Select soft key or the key.  
3. Displayed are the total numbers stored in the Phone and  
SIM and SIM (FDN).  
4. When you are finished, press the  
soft key or the  
key.  
Service Dialing Number  
You can view the list of Service Dialing Numbers (SDN)  
assigned by your service provider. These numbers  
include emergency numbers, directory enquiries and  
voice mail numbers.  
1. When the Idle screen displays, press the Menu soft key.  
Highlight Address Book and press the Select soft key or  
the key.  
78  
   
Service Dialing Number  
2. Select the Service Number option by pressing the Up or  
Down key and press the Select soft key or the key.  
3. Scroll through the numbers by using the Up or Down  
key.  
4. To dial the number displayed, press the Select soft key  
or the key.  
Note: This menu is available only when your SIM card supports Service  
Dialing Numbers.  
Section 6: Understanding Your Address Book  
79  
80  
Section 7: Messaging  
Topics Covered  
Types of Messages  
Using Instant Messenger  
Text Message  
Multimedia Message  
Browser Message  
Using Message Template  
Broadcast Message  
Chat  
Settings  
Checking Memory Status  
This section allows you to send or receive different types  
ofmessages.Italsoincludesthefeaturesand functionality  
associated with messaging.  
Section 7: Messaging  
81  
   
Type of Messages  
Your phone provides the following message types:  
Instant Messages (IM)  
Text Messages  
Multimedia Messages  
Browser Messages  
Broadcast Messages (SIM Dependent)  
Using Instant Messenger  
Instant Messenger (IM) is a way of sending short, simple  
messages that are delivered immediately to users online  
at the moment.  
Before using this feature, you need to subscribe to a  
messenger service.For further details,contact our service  
provider.  
Note: Your phone is set to use your service provider’s messenger service  
by default. You can change the configurations for Instant Messenger, such  
as the default community or auto sign on.  
Start Your Messenger  
Note: The x497 handset supports the following Instant Messaging  
Applications: AIM, ICQ, and Yahoo.  
1. In Idle mode, press the IM soft key  
Alternatively, press the Menu soft key to access Menu  
mode. Select IM and press the Select soft key or the  
key.  
82  
     
Text Messages  
2. Highlight your established IM application and press the  
Select soft key or the key.  
3. Enter your Logon ID (this field title will change reflect the  
name used in each instant message application) and  
your Password and press Options soft key and select  
Sign On and press the Select soft key.  
Note: Use the Down Navigation key to the Save password and/or Auto-  
Sign On option and press the key.  
4. Select the person you want to talk to.  
5. Start the conversation with the person as you would on a  
normal messenger for a PC.  
6. When you want to end the conversation, press the Exit  
soft key or Press the Menu soft key and select Sign Out.  
Menu Options  
Note: Menu items may vary depending on your IM provider.  
Viewing the Conversation Log  
You can view the log of your conversations in the Instant  
messenger Saved History.  
Online or offline, press the Options soft key and select  
Saved History.  
Text Messages  
Short Message Service (SMS) allows you to send and  
receive short text messages to and from other mobile  
phones. In addition, your phone supports the Enhanced  
Section 7: Messaging  
83  
   
Messaging Service (EMS), which enables you to include  
simple pictures, melodies, and animated images in your  
messages. To use this feature, you must subscribe to your  
service providers message service.  
When the Message icon ( ) appears, you have received  
new text messages. When the memory is full, an error  
message displays and you cannot receive any new  
messages. Use the Delete option in each message box to  
delete obsolete messages.  
Create  
Creating and Sending a Simple Text Message  
In this menu, you can write and send text message  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Messaging. Highlight Text Message and press  
the Select soft key or the key.  
3. Select Create and press the Select soft key or the  
key.  
4. Create your message.  
5. When you have finished writing the message, press the  
Options soft key. Choose from the following options:  
Send: allows you to send the message. The message is deleted  
after sending.  
Text Formatting: allows you to format the style of the text.  
For the Size attribute, Normal, Large, and Small size are  
available. Mode options are Normal, Underscore, and Strike  
through. Bold and Italic options are On or Off. Alignment options  
are Left, Center, and Right.  
84  
     
Text Messages  
Add Media: allows you to add a picture, melody, or animation to  
your message. Select the category of the item to be added. In  
each category, you can select from the various factory-set  
items or choose an item received from other sources, such as  
the Internet or other phones.  
Templates: allows you to apply one of the preset message  
templates to the text. Select one of the 10 items stored in the  
Templates menu.  
Save Message: allows you to save a copy of the message to the  
Phone or SIM card.  
Add from Favorites: allows you add favorite book marked URLs.  
6. Select Send to send the message. Continue to the next  
step. The Address screen displays.  
Alternatively, select Save Message to save the message  
in the Outbox folder.  
Note: For details about using other options, see the next page.  
7. Enter a destination number or press the Names soft key  
to select a contact from the Contact List. Press the  
Select soft key to display the contact number and press  
the Select soft key or the key. The Send screen  
displays.  
If you want to send the message to multiple destinations,  
scroll to the next location and press the Select soft key.  
8. When you have finished entering destination numbers,  
press the Send soft key.  
Inbox  
This message box is used to store messages that you have  
received.  
Section 7: Messaging  
85  
When you enter this menu, the list of messages in the box  
displays with the senders’ phone numbers or names, if  
available in your Address book.  
1. Select a text message from the list and press the  
Options soft key. The following options display.  
View: read the text message.  
Reply: create a new message to reply with.  
Forward: allows you to send/resend the message.  
Delete: deletes the text message.  
Call back: dials the number that sent the text message.  
2. Highlight the View option and press the Select soft key  
or the key to read the message contents.  
3. To scroll through the contents, press the Up or Down  
key.  
4. To scroll to the previous or next message, press the Left  
or Right key.  
While viewing a message, you can choose the following  
options by pressing the Options soft key:  
Reply: allows you to send a reply to the sender by sending a text  
message.  
Forward: allows you to send/resend the message.  
Delete: allows you to delete the message.  
Call Back: allows you to call the sender.  
Move to Phone: allows you to move the message from the SIM  
card to the phone’s memory. This option is only available for  
messages stored in the SIM card.  
86  
Text Messages  
Extract Address: allows you to extract the sender’s number and  
URL, e-mail addresses or phone numbers from the message  
text, so that you can save them in your phone’s memory.  
Outbox  
This message box is used to store messages that you have  
sent or will send.  
When you enter this menu, the list of messages in the box  
displays with the recipients’ phone numbers or names, if  
available in your Address book.  
1. Select a text message from the list and press the  
Options soft key.  
Options available are:  
View: read the text message.  
Delete: deletes the text message.  
Send: allows you to send the text message.  
2. Highlight the View option and press the Select soft key  
or the key to read the message contents.  
3. To scroll through the contents, press the Up or Down  
key.  
4. To scroll to the previous or next message, press the Left  
or Right key.  
While reading a message, you can choose the following  
options by pressing the Options soft key:  
Delete: allows you to delete the message.  
Extract Address: allows you to extract the sender’s number and  
URL, e-mail addresses or phone numbers from the message  
text, so that you can save them in your phone’s memory.  
Section 7: Messaging  
87  
Send: allows you to send the text message.  
Move to SIM: allows you to move the message from the phone’s  
memory to the SIM card. This option is only available for  
messages stored in the SIM card.  
Delete All  
This menu allows you to delete all of the text messages in  
each message box. You can also delete all of your  
messages at one time.  
1. From the Text Message menu, select Delete All.  
2. Select All Messages.  
To place or remove a check mark, press the Select soft  
key or the key.  
3. Press the OK soft key to delete all messages in the  
message folders.  
4. Press the Yes soft key to confirm deletion.  
5. When you have finished, press the  
key.  
Multimedia Message  
When you write a text message, the phone automatically  
splits it into severalmessages ifyour message exceeds the  
maximum number ofcharacters allowed for sending.The  
number of split messages to be sent is shown each time  
your message is split. Depending on your service  
provider, the maximum number of characters may vary.  
Create  
In this menu, you can write and send a multimedia  
message.  
88  
 
Multimedia Message  
Creating and Sending a Multimedia Message  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Messaging. Highlight Multimedia Message and  
press the Select soft key or the key.  
3. Select Create and press the Select soft key or the  
key.  
4. Create your message.  
5. Use the Up or Down Navigation key to highlight a menu  
option and press the Add soft key or the key to add  
the option.  
Subject: allows you to enter text for the subject.  
Picture: allows you to add a photo or Downloads to add one  
of the graphics stored in your graphics folder.  
Sound: allows you to add a sound file. Select Record Audio  
to record a new voice memo or My Audio to add one of the  
voice memos or sound clips stored in the phone’s memory.  
For further details about recording a voice memo, see  
"Record Audio" on page 139. You can add Downloaded  
sounds if they are in correct format and your service  
provider supports them.  
Message: enter the message text and press the key.  
While entering text, you can add a message template by  
pressing the Options soft key.  
6. Press the Opt. soft key to access the following options:  
Note: When you add media items to a message, the number of characters  
you can enter decreases.  
Preview: shows the message you created.  
Section 7: Messaging  
89  
   
Send: allows you to send message to specified number.  
Add Page: allows you to add an additional page(s).  
Page Timing: page timing allows you to set how long each page  
of the Picture Messaging message is displayed. The default  
time is 5 seconds, maximum 99 seconds.  
Text Effect: allows you to format the style of the text.  
For the Color attribute, Black, Blue, Green, Red, and Yellow are  
the colors available. For the Size attribute, Small, Medium, and  
Large sizes are available. For the Style attribute, Bold, Italic,  
and Underline are available.  
Clear Subject: clears subject from your message.  
Delete Page: deletes the page from your message.  
Save Message: allows you to save the message to Draft.  
Settings: allows you to set message parameters.  
7. Complete the message, and send or save it by following  
Inbox  
Retrieving New Messages  
While text messages from other phones are delivered  
directly to your phone,MMSmessages and emails willbe  
stored in the Inbox of the message server and the server  
will alert you to new messages. Therefore you need to  
retrieve new messages to your phone and read them on  
the phone.  
90  
Multimedia Message  
Retrieving an MMS Message  
When you receive a new MMS message, the display  
shows the MMS Message icon ( ) and a notifying text  
message.  
1. Press the View soft key or the key to view the  
sender’s phone number. The Inbox displays  
2. Press the Select soft key or press the key to view  
message.  
To scroll through the message, press the Up or Down  
Navigation keys.  
3. When you have finished, press the  
Outbox  
key.  
When you access this menu, the list of multimedia  
messages that you have sent or saved displays. The icons  
on the left tell you the status of each message:  
1. Select a message on the list and press the Select soft  
key or the key.  
The message displays and scrolls to the next page, if it  
has more than one, after a specified time.  
2. To scroll through the message, press the Up or Down  
Navigation key.  
If the message has more than one page, you can scroll  
through the pages by using the Left and Right  
Navigation keys.  
While viewing a message, you can choose the following  
options by pressing the Opt. soft key:  
Delete: allows you to delete the message.  
Section 7: Messaging  
91  
 
Replay: allows you to replay the message from the beginning.  
Send: allows you to send/resend the message.  
Properties: shows you information about the message, such as  
the time and date, to (recipient number), size, priority, and  
class.  
Draft  
After creating a multimedia message, you can store it in  
this message box to be sent at a later time.  
For further details about viewing a message in the  
Delete All  
This menu allows you to delete all of the text messages in  
each message box. You can also delete all of your  
messages at one time.  
1. From the Multimedia Message menu, select Delete All.  
2. Press the Up or Down key to select a Delete All  
parameter.  
3. To place or remove a check mark, press Select soft key  
or the key.  
4. Press the OK soft key to delete the marked objects.  
5. When the phone asks for confirmation, press the Yes  
soft key.  
6. When you have finished, press the  
key.  
Using Message Options  
While viewing a message, press the Opt. (Options) soft  
key to access the following options:  
92  
Multimedia Message  
Options for SMS Messages  
Reply: allows you to reply to the message received  
Forward: allows you to forward the message to another  
destination.  
Delete: deletes the currently selected message.  
Call Back: allows you to dial the number that the message has  
listed.  
Move to Phone: allows you to move the message to the Phone  
or SIM card’s memory.  
Extract Address: allows you to save the address from which the  
message originated.  
Options for Multimedia Messages  
Delete: deletes the message.  
Replay: allows you to replay the Sound from the message  
received.  
Reply: allows you to reply to the destination from which the  
message originated. Choose from Reply via Text Message or  
Reply via Multimedia Message.  
Reply All: allows you to reply to all addresses listed in the  
recipient list.  
Forward: allows you to forward the message to another  
destination. You may Add Subject or simply Send.  
Call Back: allows you to dial the number from which the  
message was originated.  
Save Media: allows you to save the Picture, or Sound from the  
message received.  
Extract Address: allows you to extract the recipient or sender’s  
number or address, and URL, email addresses or phone  
numbers from the message text so that you can make a call,  
send an SMS message, or save them in your phone’s memory.  
Section 7: Messaging  
93  
Properties: shows you information about the message.  
Browser Message  
This menu allows you to receive web messages from the  
server, or to set the phone not to receive Web messages.  
The following options are available:  
Inbox: allows you to read the messages received from the web  
server.  
Setting: allows you to set whether or not your phone receives  
web messages.  
Delete all: allows you to delete all of the web messages.  
Using Message Templates  
Your phone has message templates to allow you to  
retrieve them when creating a message. You can change  
the templates as your preferences or send a message  
immediately.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Messaging. Highlight Templates and press the  
Select soft key or the key.  
3. Select a template and press the Select soft key to  
access the following options:  
Edit: allows you to change the template.  
Send Message: allows you to send an SMS message using the  
template.  
Delete: deletes the template.  
4. When you have finished, press the  
key.  
94  
   
Broadcast Messages (SIM Dependent)  
Broadcast Messages (SIM Dependent)  
This network service allows you to receive text messages  
on various topics, such as the weather or traffic. Cell  
Broadcast (CB) messages display as soon as they are  
received, provided that:  
the phone is in Idle mode.  
the Receive option is set to Enable.  
the message channel is currently active on the channel list.  
Chat  
Chat allows you to participate in a synchronous exchange  
of remarks with one or more people using your handset.  
Settings  
You can set up various options for using messaging  
services.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Messaging and highlight Settings. Press the  
Select soft key or the key.  
3. Select the type of messages for which you want to  
change. Press the Select soft key or the key.  
Text Message  
The following options are available:  
Service Center: allows you to store or change the number of  
your message center, which is required when sending  
messages. You must obtain this number from your service  
provider.  
Section 7: Messaging  
95  
     
Validity Period (SIM dependent): allows you to set the length of  
time your text messages are stored at the message center  
while attempts are made to deliver them.  
Message Type (SIM dependent): allows you to view the type of  
message sent.  
Reply Path (SIM dependent): allows the recipient of your  
message to send you a reply message using your message  
center, if your network supports this service.  
Delivery Report (SIM dependent): allows you to activate or  
deactivate the report function. When this function is activated,  
the network informs you whether or not your message has  
been delivered.  
Character Support: Lets you select which character set to use in  
displaying your text messages: GSM-alphabet (Global System  
for Mobile communication), Uni-code (16-bit, multi-language),  
Automatic.  
Multimedia Message  
The following options are available:  
Send Settings  
Priority: you can select the priority level of your messages.  
Validity Period: set the length of time your messages are stored  
in the message center while the network attempts to deliver  
them.  
Delivery After: you can set a delay time before the phone sends  
your messages.  
Delivery Report: when this option is On, the network informs  
you whether or not your message has been delivered.  
Read Reply: when this option is On, your phone sends a request  
for a reply along with your message to the recipient.  
96  
Checking Memory Status  
Receive Settings  
Msg. Reception: you can set your phone to automatically  
receive or reject incoming messages.  
Anonymous Reject: you can set your phone to automatically  
reject or receive anonymous messages.  
Ads Reject: you can set your phone to automatically reject or  
receive advertising messages.  
Report Allowed: you can set the option to receive a delivery  
report.  
Multimedia Message Profiles  
Current Profile: you can select a connection profile to be used  
for sending and receiving MMS messages.  
Profile Setting: Lets you create or change your multimedia  
message connection profile(s).  
Checking Memory Status  
You can check the amount of the memory being used and  
the memory remaining for multimedia messages.  
The display shows the total space including the used and  
free space.You can also view how much space is currently  
occupied by each message box.  
1. In Idle mode, press the Menu soft key to access the  
Menu mode.  
2. Select Messaging. Highlight Memory Status and press  
the Select soft key or the key.  
3. Select the message type you want.  
For Text Message, scroll through the memory. The  
displays shows the number of messages you have  
stored in the SIM card and memory and the number of  
Section 7: Messaging  
97  
 
messages you have saved in each folder.  
For Multimedia Message, My MEdia and Games the  
displays show the total memory amount, including the  
amount of memory available and used for storing  
messages. It also shows the memory amount used for  
each message folder.  
4. When you have finished, press the  
key.  
98  
Section 8: Changing Your Settings  
Topics Covered  
Time&Date  
Phone Settings  
Display Settings  
Sound Settings  
Network Settings  
Security Settings  
Resetting Your Phone  
This section explains how to customize your settings for  
your phone.  
Section 8: Changing Your Settings  
99  
   
Time & Date  
This menu allows you to change the current time and date  
displayed.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings and highlight Time & Date. Press the  
Select soft key or the key. Select a menu and then  
change the setting. If the menu has submenus, repeat as  
necessary.  
3. When you have finished, press the  
Set Time  
key  
Allows you to enter the current time. You can choose the  
time format in the Time format menu.  
Set Date  
Allows you to enter the month, day, and year.  
Time Format  
Allows you to change the time format to 12 hours or  
24 hours.  
Auto Update  
Allows you to receive time information from your service  
providers network.  
Off: you need to manually set the time and date according to the  
current time zone using the Set time menu (Menu 9.1.1).  
On: the phone automatically updates the time and date  
according to the current time zone using the network service.  
100  
   
Phone Settings  
Confirm first: the phone asks for a confirmation before the  
update.  
Note: Automatic updates of time and date does not change the time you  
have set for alarm settings or calendar memos.  
Phone Settings  
To customize the settings for your phone use the  
following steps:  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings and highlight Phone Settings. Press the  
Select soft key or the key.  
3. Select a menu and then change the setting. If the menu  
has submenus, repeat as necessary.  
4. When you have finished, press the  
Language  
key  
You can select a display or text messaging language.  
When the language option is set to Automatic, the  
language is automatically selected according to the  
language of the SIM card used.  
Depending on your country, service provider, or the  
software version ofthe phone, the Automaticoption may  
not display.  
Greeting Message  
This menu allows you to set a greeting to be displayed  
briefly when the phone is switched on.  
Section 8: Changing Your Settings  
101  
     
Extra Settings  
You can turn the automaticredialor answer features on or  
off.  
1. From the Phone Settings menu, Select Extra Settings  
2. To turn a feature on, press the Select soft key or the  
key. A check mark displays in front of the option.  
3. To turn a feature off, press the Select soft key or the  
key. The check mark no longer displays.  
The following options are available:  
Note: The interval between call attempts varies.  
Auto redial: when this option is checked, the phone makes up to  
ten attempts to redial a phone number after an unsuccessful  
call.  
Anykey answer: when this option is checked, you can answer  
an incoming call by pressing any key, except the  
key or  
the Reject soft key. To reject the call, press the  
Reject soft key.  
key or the  
Open to Answer: when this option is checked, you can simply  
open the phone to answer a call. When it is unchecked, you  
must open the phone and press a key to answer a call,  
depending on the setting of the Anykey answer option. See  
below.  
When this option is unchecked, you must press the  
key or Accept soft key to answer a call.  
102  
 
Display Settings  
Display Settings  
In this menu, you can change various settings for the  
display or backlight.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings and highlight Display Settings and  
press the Select or key.  
3. Select a menu and then change the setting. If the menu  
has submenus, repeat this step.  
For the details of each menu, see the next sections.  
4. When you have finished, press the  
Wallpaper  
key  
This menu allows you to change the background image or  
the color of the text to be displayed in Idle mode.  
The following options are available:  
Shop Graphics: allows you to access the web site preset by your  
service provider to download images. Once you have  
downloaded images, they are saved in the Graphics folder.  
Animations: allows you to choose the multi-media or pictures  
that appear in your phone’s display when you turn it on, turn it  
off, and while in standby mode (wallpaper)  
Graphics: allows you to select a graphic that appear in your  
phone’s display when you turn it on, turn it off, and while in  
standby mode.  
Text Position: you can specify the positioning of the text in the  
display.  
Text Color: you can specify whether or not the phone displays  
the time and date on the Idle screen.  
Section 8: Changing Your Settings  
103  
     
Skin  
This menu allows you to select the menu display style.  
You can choose either Pattern 1 or Pattern 2.  
Backlight Time  
You can select the length of time the backlight is on. The  
backlight turns on when you press a key, when you open  
thephoneor you receivea callor message,and remainson  
for the specified length of time.  
Brightness Control  
You can adjust the display brightness to see it better in  
different lighting conditions.  
Press the Up or Down key or press the Volume keys to  
adjust the brightness.  
Main LCD  
You can adjust the Main LCD display brightness to see it  
better in different lighting conditions.  
Press the Up or Down key or press the Volume keys to  
adjust the brightness.  
External LCD  
You can adjust the external LCD display brightness to see  
it better in different lighting conditions.  
Press the Up or Down key or press the Volume keys to  
adjust the brightness.  
Dialing Font Color  
Dialing Font Color adjust the color ofthe numbers as they  
are entered into the display.  
104  
     
Sound Settings  
Press the Select soft key to select Black or Rainbow.  
Sound Settings  
You can customize the settings related to various sounds  
for the phone, such as the call ringer,key tone, power on/  
off tone, slider tone, and so on.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings. Highlight Sound Settings and press the  
Select soft key or the key.  
3. Select a menu and then change the setting. If the menu  
has submenus, repeat as necessary.  
4. When you have finished, press the  
Incoming Calls  
key.  
This menu allows you to specify how you are to be  
informed of incoming calls.  
The following options are available:  
Shop Ringtones: allows you to access the web site preset by  
your service provider to download melodies. Once you have  
downloaded melodies, they are saved in the Audio folder.  
Default Ringtones: allows you to use the preloaded ringtones  
that come with your phone.  
My Audio: allows you to use preloaded or downloaded  
ringtones.  
Ring Volume: allows you to adjust the ring volume to one of 5  
levels.  
Alert Type: allows you to specify how you are to be informed of  
incoming calls. The following options are available:  
Section 8: Changing Your Settings  
105  
   
Melody: the phone rings using the ring melody selected in the  
Ring Tone menu.  
Vibration: the phone vibrates but does not ring.  
Vibration then Melody: the phone first vibrates three times and  
then starts ringing.  
Keypad Tone  
This menu allows you to select the tone that the phone  
sounds when you press a key.To turn offthe sound, select  
Off.  
Message Tone  
This menu allows you to set up the ringer for incoming  
messages, text messages, multimedia messages, and  
broadcast messages  
Text Message  
This menu allows you to select how the phone informs  
you that a new text message has been received.  
The following options are available:  
Tone: allows you to use one of several message tones.  
Alert Type: allows you specify how you are informed of any  
incoming messages.  
Silent: only the text notification appears; the phone neither rings  
nor vibrates.  
Tone: the phone rings using the tone selected under the Tone  
option.  
Vibration: the phone vibrates.  
Vibration Then Tone: the phone vibrate then selected tone  
sounds.  
106  
Sound Settings  
Repetition: allows you to specify how often the phone informs  
you of a new message. The following options are available:  
Once: the phone alerts you to a new message just once at the  
time of receipt.  
Periodic: the phone alerts you to a new message every 2  
minutes until you open the message.  
Multimedia Message  
This menu allows you to select how the phone informs  
you that a new multimedia message has been received.  
The following options are available:  
Tone: allows you to use one of several message tones.  
Alert Type: allows you specify how you are informed of any  
incoming messages.  
Silent: only the text notification appears; the phone neither rings  
nor vibrates.  
Tone: the phone rings using the tone selected under the Tone  
option.  
Vibration: the phone vibrates.  
Vibration Then Tone: the phone vibrates then selected tone  
sounds.  
Repetition: allows you to specify how often the phone informs  
you of a new message. The following options are available:  
Once: the phone alerts you to a new message just once at the  
time of receipt.  
Periodic: the phone alerts you to a new message every 2  
minutes until you open the message.  
Section 8: Changing Your Settings  
107  
Power On/Off  
This menu allows you to select the melody that the phone  
sounds when it is switched on and off.  
To turn off the sound, select Off.  
Silent Mode  
Thismenu allows you to select how you are notified when  
silent mode is activated. You can specify whether the  
phone vibrates or mute all sound.  
The following options are available:  
Vibration: the phone vibrates in silent mode.  
Mute: the phone mutes the sound of an incoming call in silent  
mode.  
Note: When Silent mode is activated your keypad tones are muted. This  
feature should not be used when you access automated services that  
require you to enter numbers (such as your voice mail password).  
In idle mode press and hold the  
key, to activate or  
deactivate silent mode. When silent mode is active on  
your handset the  
appears in the top line ofthe display.  
Extra Tone  
You can customize additional tones for the phone.  
1. To turn a given tone on, press the Select soft key or the  
key. A check mark displays in front of the option.  
2. To turn a given tone off, press the Select soft key or the  
key. The check mark no longer displays in front of  
the option.  
108  
Network Services  
Network Services  
For more information about Network Services,  
Security Settings  
TheSecurity featureenablesyou to restricttheuseofyour  
phone by the others and to restrict the types of calls.  
Various codes and passwords are used to protect the  
features of your phone.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings. Highlight Security and press the Select  
soft key or the  
key.  
3. Select a menu and then change the setting. If the menu  
has submenus, repeat as necessary.  
4. When you have finished, press the  
PIN Check  
key.  
When the PIN Check feature is enabled, you must enter  
your PIN each time you switch on the phone.  
Consequently, any person who does not have your PIN  
cannot use your phone without your approval.  
Note: Before disabling the PIN Check feature, you must enter your PIN.  
The following options are available:  
Disable: the phone connects directly to the network when you  
switch it on.  
Section 8: Changing Your Settings  
109  
       
Enable: you must enter the PIN each time the phone is switched  
on.  
Change PIN  
This feature allows you to change your current PIN,  
provided that the PIN Check feature is enabled.You must  
enter the current PIN before you can specify a new one.  
Once you have entered a new PIN, you are asked to  
confirm it by entering it again.  
Phone Lock  
When the Phone Lock feature is enabled, the phone is  
locked and you must enter the 4- to 8-digit phone  
password each time the phone is switched on.  
Once the correct password has been entered, you can use  
the phone until you switch it off.  
The following options are available:  
Disable: you are not asked to enter the phone password when  
you switch on the phone.  
Enable: you are required to enter the phone password when you  
switch on the phone.  
Change Password  
The Change Password feature allows you to change your  
current phone password to a new one. You must enter the  
current password before you can specify a new one.  
110  
Security Settings  
Privacy  
Using this menu, you can lock your media contents, such  
as picture messages, Voice messages, Voice list, images,  
and sounds. Once you have locked the contents, you  
must enter the phones password to access the associated  
menus.  
1. To select an item to lock, press the Up or Down key. To  
lock all of the contents, select All.  
2. To place a check mark, press the key.  
3. To remove a check mark, press the key.  
4. To lock the marked items, press the OK soft key.  
5. When the phone asks for the password, enter the  
password and press the OK soft key or the key.  
SIM Lock  
When the SIM Lock feature is enabled, your phone only  
works with the current SIM. You must enter the SIM lock  
code to unlock the SIM so you can use a different SIM card.  
Once you have entered the lock code, you are asked to  
confirm your entry.  
FDN Mode  
FDN (Fixed Dial Number) mode, if supported by your  
SIM card, allows you to restrict your outgoing calls to a  
limited set of phone numbers.  
The following options are available:  
Disable: you can call any number.  
Enable: you can only call phone numbers stored in Phone book.  
You must enter your PIN2.  
Section 8: Changing Your Settings  
111  
Note: Not all SIM cards have a PIN2. If your SIM card does not, this menu  
does not display.  
Change PIN2  
The Change PIN2 feature allows you to change your  
current PIN2 to a new one. You must enter the current  
PIN2 before you can specify a new one. Once you have  
entered a new PIN2, you are asked to confirm it by  
entering it again.  
Note: Not all SIM cards have a PIN2. If your SIM card does not, this menu  
does not display.  
Resetting Your Phone  
You can easily reset your phone to its’ default settings.  
1. In Idle mode, press the Menu sot key to access Menu  
mode.  
2. Select Settings. Highlight Reset Settings and press the  
Select soft key or the key.  
3. Select All or a specific setting to reset.  
All  
Phone Settings  
Display Settings  
Sound Settings  
Press the Yes soft key to confirm reset.  
Press the No soft key to return to Reset Settings screen.  
112  
   
Resetting Your Phone  
4. Enter the 4 to 8-digit password and press the OK soft  
key or the key.  
Section 8: Changing Your Settings  
113  
114  
Section 9: WAP  
Topics Covered  
Launching the WAP Browser  
Accessing a WAP site  
Navigating the WAP Browser  
Using Favorites  
Downloading Multimedia Files  
Clearing the Cache  
Your phone is equipped with a WAP (Wireless  
Application Protocol) browser which allows you to  
access Internet specified for mobile phones. This section  
explains how to access the WAP services of your service  
provider and navigate the WAP browser.  
Section 9: WAP 115  
     
Launching the WAP Browser  
1. In Idle mode, press the  
key to launch the WAP  
browser.  
or  
Press the Menu soft key to access menu mode and  
select MEdia Net and press the Select soft key or the  
key.  
2. Highlight MEdia Net Home and press the Connect soft  
key or the  
key.  
Your phone is connected to the network and loads the  
homepage of the Wireless Web service provider. The  
content of the start-up homepage depends on your  
Wireless Web service provider.  
3. To scroll through the screen, use the Up and Down  
Navigation keys.  
4. To exit the browser at any time, simply press the  
key.  
Access a WAP Site  
There are several ways to access a WAP site:  
Selecting a link on the browser  
Using a bookmark item in the Favorites folder; use the  
Bookmarks option on the browser menu list or Favorites menu.  
Entering a URL address manually; use the Go To URL option on  
the browser menu list or http:// menu.  
116  
   
Navigating the WAP Browser  
Navigating the WAP Browser  
1. To scroll through browser items, press the Up or Down  
Navigation keys.  
2. To select a browser item, press the  
key or press the  
Options soft key and choose Select.  
3. To select a numbered item, press the corresponding  
numeric key.  
4. To return to the previous page, press the  
key, or  
press the Options soft key and choose Back.  
5. To access the browser menu list, press the Menu soft  
key.  
6. To return to the start-up homepage, press and hold the  
key for more than two seconds, or press the Menu  
soft key and select the Home option.  
Entering Text in the WAP Browser  
When you are prompted to enter text, the currently active  
text input mode is indicated on the screen. To change the  
text input mode, press the  
key one or more times.  
The following modes are available:  
Upper-Case Alphabet Mode (A)  
allows you to enter upper-case characters.  
Lower-Case Alphabet Mode (a)  
allows you to enter lower-case characters.  
Note: You can enter symbols in upper or lower case alphabet mode by  
pressing the  
key.  
Section 9: WAP 117  
 
T9 Mode (T9)  
allows you to enter characters by pressing one key per  
letter. In this mode, you can use only the key to  
display alternative words. To change case, press the  
key.  
Number Mode (1)  
allows you to enter numbers.  
Selecting and Using Menu Options  
Various menus are available when using the WAP  
Browser to navigate the Wireless Web.  
To access menu options, using the Up or Down  
Navigation key,scrollto the WAP Browser icon (a blue  
square willdisplay around the icon)and press the key.  
The following options display:  
Go to URL: allows you to manually enter the URL address of a  
WAP site. After entering an address, press the OK soft key to go  
there directly.  
Favorites: shows the bookmarks list. You can bookmark the  
current page or access previously book marked pages.  
Text Message: allows you to send messages using the WAP  
server.  
My Media: displays My MEdia menu.  
Home: takes you back at any time to the homepage of the  
Wireless Web service provider.  
Back: allows you to move back one page.  
Show URL: displays the URL address of the page to which you  
are currently connected. It also enables you to set the current  
site as the startup homepage.  
118  
Using Favorites  
Reload: reloads the current page.  
Using Favorites  
While navigating the WAP browser, you can bookmark  
the site to quickly and easily access it at a future time. The  
URL addresses of the book marked sites are stored in the  
Favorites folder, wherein you can use the 5-preset URL  
addresses and store your favorite URL addresses.  
Accessing a WAP Site Using Favorites  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Highlight MEdia Net and press the Select soft key or the  
key.  
3. Select Favorites.  
4. Select a bookmark item from the Favorite list and press  
the Select soft key or the  
key.  
5. Select the option Go. You are accessed to the  
corresponding WAP site.  
Storing a URL Address  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Highlight MEdia Net and press the Select soft key or the  
key.  
3. Select Favorites.  
4. Select an Empty location, and press the Select soft key  
or  
key.  
Section 9: WAP 119  
 
5. Enter the address and press the OK soft key or the  
key.  
6. Enter a name for the bookmark and press the OK soft key  
or the  
key. The bookmark name displays in the  
selected location.  
7. When you have finished, press the  
key.  
Editing a Bookmark  
1. From the Favorite list, select the bookmark you want to  
change.  
2. Select Edit.  
3. Change the address and the name, as you would when  
storing a new one.  
4. When you have finished, press the  
key.  
Deleting a Bookmark  
1. From the Favorites list, select the bookmark you want to  
delete.  
2. Select Delete.  
3. Press the Yes soft key or the  
key to confirm the  
press the key.  
deletion.  
4. When you have finished,  
120  
Downloading Multimedia Files  
Downloading Multimedia Files  
You can buy a variety of multimedia files, such as  
ringtones, graphics, applications, Multimedia contents,  
and so on from the WAP browser and download them to  
your phones memory. Your phone has embedded links  
to the WAP site providing you with download services,  
preset by your service provider.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select MEdia Mall. Highlight Shop Ringtones, Shop  
Games, Shop Graphics, Shop Multimedia, or Shop  
Applications, depending on the type of items you want  
to buy.  
To access homepage of the online shopping mall, select  
MEdia Home.  
3. Find the item you want to download and follow the  
instructions on the screen to purchase it.  
Note: This content is delivered to you in Multimedia messages. You can  
retrieve the messages from the server and then save the items in your  
phone’s memory. you cannot forward these messages to other people or  
add the saved items to an Multimedia message.  
Clearing the Cache  
The cache is the phones temporary memory in which the  
most recently accessed WAP pages are stored. You can  
clear the cache at anytime.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
Section 9: WAP 121  
     
2. Highlight MEdia Net and press the Select soft key or the  
key.  
3. Select Clear Cache.  
4. Press the Yes soft key or the  
key to confirm deletion.  
key  
5. When you have finished, press the  
Changing the WAP Profiles  
You can set up 5 server profiles for the WAP browser.  
1. In Idle mode, press the Menu soft key to access menu  
mode and select MEdia Net and press the Select soft  
key or the  
2. Using the Up or Down Navigation key scroll to Browser  
Profiles and press the Select soft key or the key.  
3. Scroll to Profile Settings and press the Select soft key  
or the key.  
key.  
4. Select the profile you want.  
For each profile, the following options are available:  
Profile Name: enter a name that you wish to assign to the HTTP  
proxy server.  
Home URL: set the address of your startup homepage. When  
the default homepage displays, you can delete it using the  
key and enter your own choice.  
Bearer: select the bearer to be used for each type of network  
address accessed: GPRS First, GPRS Only or GSM Only.  
Proxy Use: enter the WAP gateway address required to connect  
to the Internet.  
122  
Clearing the Cache  
GPRS Setting:  
Proxy Address: enter the WAP gateway address required to  
connect to the Internet.  
Proxy Port: enter the Proxy port required to connect to the  
Internet.  
APN: enter the access point name used for the address of the  
GPRS network gateway.  
Login ID: enter the Login ID required to connect to the GPRS  
network.  
Password: enter the password required to connect to the  
GPRS network.  
GSM Setting:  
Proxy Address: enter the WAP gateway address required to  
connect to the Internet.  
Proxy Port: enter the Proxy port required to connect to the  
Internet.  
Dial Number: enter the server phone number.  
Login ID: enter the Login ID required to connect to the GSM  
network.  
Password: enter the password required to connect to the  
GSM network.  
Data Call Type: select the data call type: ISDN or Analog.  
Note: The WAP settings may vary depending on the service provider.  
Section 9: WAP 123  
124  
Section 10: Personal Organizer  
Topics Covered  
Alarms  
Organizer  
Using the Calendar  
Using the To Do List  
Using the Calculator  
Record Audio  
Unit Conversion  
Using the Timer  
Stopwatch  
WorldTime  
The topics covered in this section allow you to schedule  
appointments, view the calendar, create To-Do lists, set  
an alarm, and perform simple math calculations.  
Section 10: Personal Organizer  
125  
   
Alarms  
You can set thealarm to ring at a specifictime.You can also  
set the phone to switch on automatically and ring the  
alarm even if the phone is switched off.  
Setting an Alarm  
1. In Idle mode, press the Menu soft key and select Games  
& Applications.  
2. Highlight Alarm and press the Select soft key or the  
key.  
3. Select an Alarm Type  
Wake-up Call: the alarm rings to wake you up at the specified  
time.  
Alarm 1: primary alarm setting.  
Alarm 2: secondary alarm setting.  
Auto Power: the alarm rings even when the phone is turned off.  
4. Press the Select soft key or the key.  
Note: Your phone is preset to a 12-hour format.  
If you want to use the alarm options, press the Options  
soft key. The following options are available:  
Alarm Day: select the day or days the alarm will sound.  
Alarm Time: select the time the alarm will sound  
Alarm Tone: select the sound of the alarm  
Remove Alarm: removes alarm settings.  
5. Highlight Alarm Day and press the Select soft key.  
126  
   
Alarms  
6. Highlight the days you want the alarm to sound and  
press the Select soft key or the key. Press the OK  
soft key when finish. The Alarm Time screen displays.  
7. Enter the time for the alarm to sound using the  
alphanumeric keypad. Press the OK soft key or the  
key.  
8. Select AM or PM and press the Select soft key or the  
key.  
To stop the alarm when it rings, open the phone and  
press the Confirm soft key.  
Setting Autopower Alarms  
You can set the phone to ring the alarm when the time for  
an alarm comes, if the phone is switched off.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Alarm and  
press the Select soft key or the key.  
3. Select Autopower.  
4. Select On to activate the Autopower feature. The phone  
will automatically switch on to ring the alarm when the  
alarm time comes.  
If the menu option is set to Off, and the phone is  
switched off at the specified time, the alarm does not  
ring.  
5. When you have finished, press the  
key.  
Section 10: Personal Organizer  
127  
Deactivating Alarms  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Alarm and  
press the Select soft key or the  
key.  
3. Select Alarm Type and press the Select soft key or the  
key.  
4. Press the Options soft key and highlight Remove Alarm  
and press the Select soft key or the  
key.  
A pop-up message displays confirming Alarm  
Deactivate. Press Yes to remove or No to exit.  
5. When you have finished, press the  
key.  
Using Organizer  
Organizer is a suite of PIM (Personal Information  
Management)applications such as a Calendar,To Do List,  
and Memo Pad. Schedule events, set reminders, create to  
do lists, perform calculations, and more with the digital  
assistant functionality of this useful feature.  
1. Press the Menu soft key and select Games &  
Applications.  
2. Highlight Organizer and press the Select soft key or the  
key. The following appear in the display.  
New Memo: Enter a memo, which can be viewed at any time.  
Memos do not have an alarm setting.  
Calendar: Schedule events for any day by indicating each  
event’s start and end time.  
To Do List: Enter up to 25 tasks and set an alarm for each.  
128  
   
Using Organizer  
3. Use the Navigation key to highlight an application. Press  
the Select soft key or the key to enter the highlighted  
application’s sub menu. The following sections provide a  
detailed description on each application and its function.  
Writing a Memo  
Create and store notes in Memo Pad. You cant prioritize  
or set an alert for stored notes. Return to Memo Pad  
anytime to review and edit your notes.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
3. Highlight New Memo and press the Select soft key or  
the key.  
key.  
4. Add a new memo.  
5. While entering a memo, press the right soft key Options  
to display a the following text entry modes:  
ABC Mode  
T9 Mode  
Symbolic  
Number  
Add Word  
Language Select  
6. Highlight the text mode and press the Select soft key or  
the  
key.  
Section 10: Personal Organizer  
129  
7. When youre finished entering details for the memo,  
press the left soft key OK. The Save to sub menu appear  
in the display.  
8. Highlight Save to option and press the Select soft key or  
the key. The calendar displays with today’s date  
highlighted.  
9. Using the Navigation key select a date and press the  
Select soft key or the  
10. Using the keypad enter the memo time and press the OK  
soft key or the key.  
key.  
11. Select AM or PM, press the Select soft key or the  
key. The Alarm Time screen appear in the display.  
12. Press the Yes soft key to set alarm.  
Press the No soft key to save memo.  
13. Using the keypad enter the Alarm time and press the OK  
soft key or the  
key  
14. Select AM or PM, press the Select soft key or the  
key. The Alarm Tone screen displays.  
15. Using the Navigation key scroll alarm tones.  
16. Select alarm tone using the Select soft key or the  
key.  
Using Memo Pad Options  
You can access the following options by pressing the  
Options soft key:  
Add: allows you to add a memo.  
Delete: deletes a memo.  
130  
Using the Calendar  
Edit: allows you to edit the content of your memo.  
Move: allows you to move a memo.  
Copy: allows you to copy a memo.  
Using the Calendar  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight Calendar and press the Select soft key or the  
key. The calendar displays with today’s date  
highlighted.  
4. Scroll to a date on the calendar by pressing the  
Navigation key and the Select soft key or the  
key.  
Alternatively, press the Options soft key and select Go  
to Date. You can enter manually a specific date and  
press the OK soft key or the key.  
An empty memo screen displays allowing you to enter  
your memo.  
5. While entering your memo, press the right soft key  
Options to display a pop-up menu with the following  
text entry modes:  
ABCMode  
T9Mode  
Symbolic  
Number  
Add Word  
Language Select  
Section 10: Personal Organizer  
131  
 
6. Highlight the text mode and press the Select soft key or  
the key.  
7. When youre finished entering details for the memo,  
press the left soft key OK. The Save to sub menu appear  
in the display.  
Scheduler  
To Do List  
Call  
Anniversary  
8. Highlight Save to option and press the Select soft key or  
the key.  
9. Using the keypad enter the memo time and press the OK  
soft key or the  
key.  
10. Select AM or PM, press the Select soft key or the  
key. The Alarm Time screen appear in the display.  
The color of the date on the calendar changes to blue to  
indicate that a memo exist for that date.  
11. If you want an alarm to ring on the chose day press the  
Yes soft key or the key to set alarm. If not, Press the  
No soft key. The memo is saved.  
12. Using the keypad enter the Alarm time and press the OK  
soft key or the  
key  
13. Select AM or PM, and press the Select soft key or the  
key. The Alarm Tone screen displays.  
14. Using the Navigation key scroll through alarm tones.  
15. Select alarm tone using the Select soft key or the  
key.  
132  
Using the Calendar  
16. When you have finished, press the  
key.  
Consulting the Calendar  
Viewing Memos on the Selected Date  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight Calendar and press the Select soft key or the  
key. The calendar displays with today’s date  
highlighted.  
4. Select the date you want to view its memo(s).  
If there is more than one memo for that date, the latest  
memo displays  
5. Press the Up or Down key to scroll to the previous or  
next memo  
If you want to make a new memo for that date, press the  
Options soft key.  
Add Memo: allows you to add new memo.  
Go to Date: allows you to go directly to a specified date. Enter  
the date using the keypad.  
View All: allows you to view all memos in the calendar.  
Delete Day: allows you to delete the memo for that day.  
Delete All: allows you to delete all memos in the calendar.  
6. When you have finished, press the  
key.  
Section 10: Personal Organizer  
133  
Viewing All of the Memos on the Calendar  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight Calendar and press the Select soft key or the  
key. The calendar displays with today’s date  
highlighted.  
4. Press the Options soft key and select View All. The  
phone displays the latest memo. You can view all of the  
memos, starting with the oldest, regardless of the date.  
5. To scroll through the memos, press the Left or Right  
Navigation key  
6. When you have finished, press the  
Deleting Memos  
key.  
You can delete memos on the calendar one by one or all at  
one time.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight Calendar and press the Select soft key or the  
key. The calendar displays with today’s date  
highlighted.  
4. Select the date you want to view its memo(s),  
If there is more than one memo for that date, the latest  
memo displays.  
134  
Using the To Do List  
5. Press the Left or Right Navigation key to scroll to the  
previous or next memo.  
6. Press the Options soft key and select Delete.  
7. Press the Yes soft key to confirm deletion.  
8. When you have finished, press the  
key.  
Deleting All Memos  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight Calendar and press the Select soft key or the  
key. The calendar displays with today’s date  
highlighted.  
4. Press the Options soft key and select Delete All.  
5. Press the Yes soft key to confirm deletion.  
6. When you have finished, press the  
key.  
Using the To Do List  
The To Do List allows you to  
enter a list of task to be done  
assign a priority and a deadline to each task  
sort the tasks by priority and status  
Creating a To Do List  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
Section 10: Personal Organizer  
135  
   
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the key.  
3. Highlight To Do List and press the Select soft key or the  
key. Youre prompted to add a new memo.  
4. While entering a memo, press the right soft key Options  
to display a pop-up menu with the following text entry  
modes  
ABC Mode  
T9Mode  
Symbolic  
Number  
AddWord  
Language Select  
5. Highlight the text mode and press the Select soft key or  
the key.  
6. When youre finished entering details for the memo,  
press the OK soft key. The Calendar displays.  
7. Using the Navigation key select a date and press the  
Select soft key or the  
8. Using the keypad enter the memo time and press the OK  
soft key or the key.  
key.  
9. Select AM or PM,and press the Select soft key or the  
key. The Alarm Time screen appear in the display.  
10. Press the Yes soft key to set alarm.  
Press the No soft key to save memo.  
11. Using the keypad enter the alarm time and press the OK  
soft key or the  
key  
136  
Using the To Do List  
12. Select AM or PM, press the Select soft key or the  
key. The Alarm Tone screen displays.  
13. Using the Navigation key scroll alarm tones.  
14. Select alarm tone using the Select soft key or the  
key.  
15. When you have finished, press the  
key.  
Adding Tasks to the To Do List  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight To Do List and press the Select soft key or the  
key.  
4. Press the Options soft key and Select Add. Continue  
Viewing the To Do List  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Organizer and  
press the Select soft key or the  
key.  
3. Highlight To Do List and press the Select soft key or the  
key. The tasks displays.  
4. You can scroll through the task using the Up and Down  
Navigation key, if necessary.  
5. When you have finished, press the  
key.  
Section 10: Personal Organizer  
137  
Using To Do List Options  
You can access the following options by pressing the  
Options soft key  
Add: allows you to add a new task  
Mark: allows you to change the status of a task. Select  
appropriate status (Done or Undo)  
Edit: allows you to edit a task. You can change the text priority,  
and/or deadline for the task.  
Move: allows you to move a task.  
Copy: allows you to copy a task.  
Delete: deletes a task.  
Delete All: allows you to delete all tasks.  
Using the Calculator  
You can use the phone as a calculator. The calculator  
provides basic arithmetic functions: addition,  
subtraction, multiplication, and division using your  
phone.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Calculator and  
press the Select soft key or the  
key.  
3. Enter the first number in your equation using the keypad.  
Press the  
Press the  
to enter a decimal point  
to set the type of calculation you that you  
wish to perform. Your choices are as follows  
• [+ ] Addition  
138  
   
Record Audio  
• [ - ] Subtraction  
• [ x ] Multiplication  
[÷ ]Division  
[%]Percentage  
• [ ( ] Open Parenthesis  
• [ ) ]ClosedParenthesis  
4. Use the keypad to enter the second number into your  
equation.  
5. Press the Equal soft key or the  
key to perform the  
operation and view your results in the Answer field of  
the Calculator screen.  
6. Repeat steps 3 to 5 as many times as required.  
7. When you have finished, press the  
key.  
Record Audio  
This menu allows you to record a new memo.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. The following sub menu  
displays.  
3. Highlight Record Audio and press the Select soft key or  
the  
key.  
4. Highlight Record and press the Select soft key or the  
key. The following icons appear in the bottom of the  
display:  
Record  
Stop  
Play  
Section 10: Personal Organizer  
139  
   
Rewind  
Fast Forward  
5. Press the Select soft key or the  
key to start  
recording.  
Record a memo by speaking into the microphone.  
6. When you press the Select soft key or the key to stop  
recording or the time expires. The audio is automatically  
saved and the  
play icon is highlighted in red.  
7. Press the Select soft key or the key to play recording.  
During playback the following playback options are  
available.  
Stop  
Play  
Rewind  
Fast Forward  
Pause  
8. Press the Options soft key to display the following  
Send: allows you to send the recorded audio to other people by  
using the MMS feature. For details about sending a multimedia  
Rename: allows you to rename the recording.  
Delete: deletes the recording.  
Properties: displays detailed information about the recorded  
audio message such as name, size and format.  
9. When you have finished, press the  
key.  
140  
Record Audio  
Reviewing a Recorded Audio  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. The following sub menu  
displays.  
3. Highlight Record Audio and press the Select soft key or  
the  
4. Highlight Recorded Audio and press the Select soft key  
or the key. A list of recorded audios display.  
key.  
5. Scroll to an audio file. Press the Select soft key or the  
key to play audio.  
6. Press the Options soft key to display the following.  
Send: allows you to send the recorded audio to other people by  
using the MMS feature. For details about sending a multimedia  
Rename: allows you to rename the recording.  
Delete: deletes the recording.  
Properties: displays detailed information about the recorded  
audio message such as name, size and format.  
7. When you have finished, press the  
key.  
Deleting Recorded Audios  
You can delete your recorded audios one by one or all at  
one time.  
1. Access the Recorded Audio menu and select the audio  
file you want to delete.  
2. Press the Select soft key or the key.  
Section 10: Personal Organizer  
141  
3. Press the Options soft key and then select Delete.  
4. Press the Yes soft key or the key to confirm deletion.  
key.  
5. When you have finished, press the  
Delete All Recorded Audios  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Record Audio  
and press the Select soft key or the  
key.  
3. Scroll down using the Navigation key and highlight  
Delete All and press the Select soft key or the key.  
4. Press the Yes soft key or the  
to confirm Delete All.  
key.  
5. When you have finished, press the  
Changing Record Audio Settings  
You can change the default settings for using Record  
Audio.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Record Audio  
and press the Select soft key or the  
key.  
3. Select Settings and press the Select soft key or the  
key.  
The following options are available:  
Recording Time: allows you to set recording time.  
Volume: allows you to set the sound volume.  
Default Name: allows you to set a default name for all recorded  
audio.  
142  
Using Unit Conversion  
4. When you have finished, press the  
key.  
Checking Memory Status  
You can check the amount of memory being used and the  
memory remaining for voice memos.  
The display shows you the total, used, and free memory,  
including the number of memos you stored and the total  
number of memos you can store.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Record Audio  
and press the Select soft key or the  
key.  
3. Select Memory Status.  
This display show the Total, Used and Free memory  
amount for My MEdia, Games, and Multimedia  
Messages.  
4. When you have finished, press the  
key.  
Using Unit Conversion  
You can use the phone as a unit converter. The unit  
converter provides basic conversion functions: length,  
weight, volume, area, and temperature.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Unit  
Conversion and press the Select soft key or the key.  
The unit conversion sub menu appear display.  
Length  
Weight  
Section 10: Personal Organizer  
143  
 
Volume  
Area  
Temperature  
3. Use the Navigation key to highlight a conversion option  
and press the Select soft key or the  
key.  
4. Enter the amount to convert. Use the Navigation key to  
select the conversion method.  
Using the Timer  
Timer allows you to view the amount oftime between the  
current day and any event that you wish to schedule.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight Timer and  
press the Select soft key or the  
key. The Timer  
screen appear in the display.  
3. Press the Set soft key to set timer.  
4. Using the keypad enter the time and press the OK soft  
key.  
5. Press the Start soft key to start timer.  
Press the Stop soft key to stop timer.  
Stopwatch  
You can use this menu to set a stop watch. Press the OK  
soft key to start the stopwatch. Press the Reset soft key to  
erase all stop watch times recorded.  
World Time  
144  
       
World Time  
World Time allows you to view the time ofday or night in  
any part of the world.  
1. In Idle mode, press the Menu soft key to access menu  
mode.  
2. Select Games & Applications. Highlight World Time  
and press the Select soft key or the  
key.  
3. Use the Navigation key to display the city (or cities),  
date, and time that you wish to view. The following cities  
are supported.  
Chicago  
NewYork  
Caracas  
Rio  
GMT  
London  
Paris  
Cairo  
Moscow  
Dubai  
Karachi  
Delhi  
Dacca  
Bangkok  
Beijing/H.K.  
Seoul  
Sydney  
Noumea  
Wellington  
Section 10: Personal Organizer  
145  
Honolulu  
Anchorage  
LA  
Denver  
146  
Section 11: Network Services  
Topics Covered  
Network Services  
Call Forwarding  
Call Waiting  
Network Selection  
Caller ID  
This section allows set up the network functions  
supported by your carrier.Some ofthese services may not  
be available due to coverage area or service plans. If you  
have any questions,please contact the Customer Support  
center.  
Section 11: Network Services  
147  
     
Network Services  
You can customize the settings for network features,such  
as call forwarding, and call waiting.  
1. In Idle mode, press the Menu soft key to access Menu  
mode.  
2. Select Settings and highlight Network Services. Press  
the Select soft key or the key.  
3. Select a menu and then change the setting. If the menu  
has submenus, repeat as necessary.  
4. When you have finished, press the  
key  
Call Forwarding  
This network service enables incoming calls to be  
rerouted to the number that you specify.  
For example,you may wish toforward your businesscalls  
to a colleague while you are on vacation.  
1. From the Network Services menu screen, select Call  
Forwarding and press the Select soft key or the key.  
2. Select one of the following call forwarding options.  
Forward Always: all calls are forwarded  
Busy: calls are forwarded when you are already on another call  
No Reply: calls are forwarded when you do not answer the  
phone.  
Unreachable: calls are forwarded when you are not in an area  
covered by your service provider or when your phone is  
switched off.  
Cancel All: all call forwarding options are canceled.  
148  
       
Call Waiting  
3. Select the type of calls, Voice Calls or Data Calls. The  
current status displays. If the option has already been  
set, the number to which the calls are forwarded  
displays.  
4. Press the Activate soft key or the  
5. Using the keypad enter the forwarding number and press  
the OK soft key or the key.  
key.  
Call Waiting  
Thisnetwork serviceinformsyou when someoneistrying  
to reach you during another call. You can specify  
individualcallwaiting optionsfor voicecallsand/ or data  
calls.  
Section 11: Network Services  
149  
   
Setting Call Waiting Options  
1. From the Network Services menu screen, select Call  
Waiting.  
2. Select the type of calls, Voice Calls or Data Calls. The  
screen informs you whether call waiting is activated or  
deactivated.  
3. Press the Activate soft key or the key to activate the  
call waiting feature.  
4. The phone sends your settings to the network and the  
network’s acknowledgement displays.  
150  
Network Selection  
Deactivating Call Waiting Settings  
1. From the Network Services menu screen, select Call  
Waiting.  
2. Select the type of calls, Voice Calls or Data Calls. The  
screen informs you whether call waiting is activated or  
deactivated.  
Select Cancel All to cancel all call waiting options.  
3. Press the Deactivate soft key or the  
key.  
4. The phone sends your settings to the network and the  
network’s acknowledgement displays.  
Network Selection  
The Network Selection feature enables you to  
automatically or manually select the network used when  
roaming outside of your home area.  
Note: You can select a network other than your home network only if there  
is a valid roaming agreement between the two.  
1. From the Network Services menu screen, select  
Network Selection.  
2. Select the options you want.  
If you select Automatic, you are connected to the first  
available network when roaming.  
If you select Manual, go to step 3.  
3. Select the network you want. The phone will scan for  
that network and you will be connected.  
Section 11: Network Services  
151  
   
Caller ID  
You can prevent your phone number from being  
displayed on the phone of the person you are calling.  
Note: Some networks do not allow you to change this setting.  
The following options are available:  
Default: the default setting provided by the network is used.  
Hide Number: you number does not display on the other  
person’s phone.  
Send Number: your number is sent each time you make a call.  
152  
   
Section 12: Games  
Topics Covered  
Shop Games  
MyGames  
Settings  
Memory Status  
This section outlines the available gaming options and  
accessoriesfor your phone.For moreinformation,contact  
your service provider.  
Section 12: Games  
153  
 
Shop Games  
Your phone is equipped with a WAP (Wireless  
Application Protocol) browser to allow you to access and  
navigate the Wireless Web using your phone. For more  
You can download MIDlets (Java applications that run on  
mobile phones) from various sources using the WAP  
browser and store them in your phone. When you access  
the Games menu, the list of default games appears. Once  
you have downloaded games, they are added to the list.  
Note: Java services may not be available, depending on your service plan  
and phone model.  
My Games  
My Games stores all downloaded games.  
Settings  
You can customize the profiles containing the settings for  
connecting your phone to the network. These settings are  
also used for the WAP browser or Instant Messenger, or  
sending Multimedia messages or Emails.  
APN: enter the access point name used for the address of the network.  
Login ID: enter the user ID required to connect to the network.  
Password: enter the password required to connect to the network.  
DNS Settings: enter the DNS (Domain Name System) address.  
154  
           
Memory Status  
Memory Status  
You can check the amount of memory being used and  
memory remaining for games, multimedia messages,  
and My MEdia.  
Section 12: Games  
155  
   
156  
Section 13: Health and Safety  
Information  
Topics Covered  
Health and Safety Information  
Consumer Information on Wireless Phones  
Road Safety  
Operating Environment  
Using Your Phone Near Other Electronic Devices  
Potentially Explosive Environments  
EmergencyCalls  
FCC Notice and Cautions  
Other Important Safety Information  
Product Performance  
Availability of Various Features/Ring Tones  
Battery Standby and Talk Time  
Battery Precautions  
Care and Maintenance  
This section outlines the safety precautions associated  
with using your phone. These safety precautions should  
be followed to safely use your phone.  
Section 13: Health and Safety Information  
157  
   
Health and Safety Information  
Exposure to Radio Frequency (RF) Signals  
Certification Information (SAR)  
Your wireless phone is a radio transmitter and receiver. It  
is designed and manufactured not to exceed the exposure  
limits for radio frequency (RF) energy set by the Federal  
Communications Commission (FCC) of the U.S.  
government. TheseFCCexposurelimitsarederived from  
the recommendations of two expert organizations, the  
National Counsel on Radiation Protection and  
Measurement (NCRP) and the Institute of Electrical and  
Electronics Engineers (IEEE). In both cases, the  
recommendations were developed by scientific and  
engineering experts drawn from industry, government,  
and academia after extensive reviews of the scientific  
literature related to the biological effects of RF energy.  
The exposure limit set by the FCC for wireless mobile  
phones employs a unit of measurement known as the  
Specific Absorption Rate (SAR). The SAR is a measure of  
the rate of absorption of RF energy by the human body  
expressed in units of watts per kilogram (W/ kg). The  
FCC requires wireless phones to comply with a safety  
limit of 1.6 watts per kilogram (1.6 W/ kg). The FCC  
exposurelimit incorporates a substantialmargin ofsafety  
to give additional protection to the public and to account  
for any variations in measurements.  
158  
 
Health and Safety Information  
SAR tests are conducted using standard operating  
positions accepted by the FCC with the phone  
transmitting at its highest certified power level in all  
tested frequency bands. Although the SARis determined  
at the highest certified power level,theactualSARlevelof  
the phone while operating can be well below the  
maximum value. This is because the phone is designed to  
operate at multiple power levels so as to use only the  
power required to reach the network. In general, the  
closer you are to a wireless basestation antenna,the lower  
the power output.  
Before a new model phone is available for sale to the  
public, it must be tested and certified to the FCC that it  
does not exceed the exposure limit established by the  
FCC. Tests for each model phone are performed in  
positions and locations (e.g. at the ear and worn on the  
body)as required by the FCC. Body-worn operations are  
restricted to Samsung-supplied, approved, or non-  
Samsung designated accessories that have no metal and  
must provide at least 1.5 cm separation between the  
device, including its antenna (whether extended or  
retracted)and the user's body. Non-compliance with the  
above restrictions may result in violation of FCC RF  
exposure guidelines.  
The FCC has granted an Equipment Authorization for  
this mobile phone with all reported SAR levels evaluated  
as in compliance with the FCC RF exposure guidelines.  
The maximum SAR values for this model phone as  
reported to the FCC are:  
Section 13: Health and Safety Information  
159  
Head:1.4 W/Kg.  
Body-worn: 1.42 W/Kg.  
SAR information on this and other model phones can be  
viewed on-line at www.fcc.gov/ oet/ fccid. To find  
information that pertains to a particular model phone,  
this site uses the phone FCC ID number which is usually  
printed somewhere on the case of the phone. Sometimes  
it may be necessary to remove the battery pack to find the  
number. Once you have the FCC ID number for a  
particular phone, follow the instructions on the website  
and it should providevalues for typicalor maximum SAR  
for a particular phone. Additional product specific SAR  
information can also be obtained at www.fcc.gov/ cgb/  
sar.  
Consumer Information on Wireless Phones  
The U.S. Food and Drug Administration (FDA) has  
published a series of Questions and Answers for  
consumers relating to radio frequency (RF) exposure  
from wireless phones. The FDA publication includes the  
following information:  
What kinds of phones are the subject of this update?  
Theterm wirelessphonerefershereto hand-held wireless  
phones with built-in antennas, often called "cell,"  
"mobile," or "PCS" phones. These types of wireless  
phones can expose the user to measurable radio  
frequency energy (RF) because of the short distance  
between the phone and the user's head. These RF  
exposures are limited by Federal Communications  
Commission safety guidelines that were developed with  
the advice of FDA and other federal health and safety  
160  
 
Consumer Information on Wireless Phones  
agencies. When the phone is located at greater distances  
from the user, the exposure to RF is drastically lower  
because a person's RF exposure decreases rapidly with  
increasing distance from the source. The so-called  
"cordless phones," which have a base unit connected to  
the telephone wiring in a house, typically operate at far  
lower power levels, and thus produce RF exposures well  
within the FCC's compliance limits.  
Do wireless phones pose a health hazard?  
The available scientific evidence does not show that any  
health problems are associated with using wireless  
phones. There is no proof, however, that wireless phones  
are absolutely safe. Wireless phones emit low levels of  
radio frequency energy (RF) in the microwave range  
while being used. They also emit very low levels of RF  
when in the stand-by mode. Whereas high levels of RF  
can produce health effects (by heating tissue), exposure  
to low level RF that does not produce heating effects  
causes no known adverse health effects. Many studies of  
low level RF exposures have not found any biological  
effects. Some studies have suggested that some  
biological effects may occur, but such findings have not  
been confirmed by additional research. In some cases,  
other researchers have had difficulty in reproducing  
those studies, or in determining the reasons for  
inconsistent results.  
What is FDA's role concerning the safety of wireless  
phones?  
Under the law, FDA does not review the safety of  
radiation-emitting consumer products such as wireless  
Section 13: Health and Safety Information  
161  
phones before they can be sold, as it does with new drugs  
or medicaldevices. However,the agency has authority to  
take action if wireless phones are shown to emit radio  
frequency energy (RF) at a level that is hazardous to the  
user. In such a case,FDA could require the manufacturers  
ofwirelessphones to notify users ofthehealth hazard and  
to repair,replace or recallthe phones so that the hazard no  
longer exists.  
Although the existing scientific data do not justify FDA  
regulatory actions, FDA has urged the wireless phone  
industry to take a number of steps, including the  
following:  
"Support needed research into possible biological effects of RF  
of the type emitted by wireless phones;  
"Design wireless phones in a way that minimizes any RF  
exposure to the user that is not necessary for device function;  
and  
"Cooperate in providing users of wireless phones with the best  
possible information on possible effects of wireless phone use  
on human health.  
FDA belongs to an interagency working group of the  
federal agencies that have responsibility for different  
aspects of RF safety to ensure coordinated efforts at the  
federal level. The following agencies belong to this  
working group:  
"National Institute for Occupational Safety and Health  
"Environmental Protection Agency  
"Federal Communications Commission  
"Occupational Safety and Health Administration  
"National Telecommunications and Information Administration  
162  
Consumer Information on Wireless Phones  
The National Institutes of Health participates in some  
interagency working group activities, as well.  
FDA shares regulatory responsibilities for wireless  
phones with the Federal Communications Commission  
(FCC). All phones that are sold in the United States must  
comply with FCC safety guidelines that limit RF  
exposure. FCC relies on FDA and other health agencies  
for safety questions about wireless phones.  
FCC also regulates the base stations that the wireless  
phone networks rely upon. While these base stations  
operate at higher power than do the wireless phones  
themselves, the RF exposures that people get from these  
base stations are typically thousands of times lower than  
those they can get from wireless phones. Base stations are  
thus not the primary subject of the safety questions  
discussed in this document.  
What are the results of the research done already?  
The research done thus far has produced conflicting  
results, and many studies have suffered from flaws in  
their research methods. Animal experiments  
investigating the effects of radio frequency energy (RF)  
exposures characteristicofwireless phones have yielded  
conflicting results that often cannot be repeated in other  
laboratories. A few animal studies, however, have  
suggested that low levels of RF could accelerate the  
development of cancer in laboratory animals. However,  
many of the studies that showed increased tumor  
development used animals that had been genetically  
engineered or treated with cancer-causing chemicalsso as  
to be pre-disposed to develop cancer in absence of RF  
exposure. Other studies exposed the animals to RFfor up  
Section 13: Health and Safety Information  
163  
to 22hours per day. Theseconditionsarenot similar to the  
conditions under which people use wireless phones, so  
we don't know with certainty what the results of such  
studies mean for human health.  
Three large epidemiology studies have been published  
since December 2000. Between them, the studies  
investigated any possible association between the use of  
wireless phones and primary brain cancer, glioma,  
meningioma, or acousticneuroma, tumors ofthe brain or  
salivary gland, leukemia, or other cancers. None of the  
studies demonstrated the existence ofany harmfulhealth  
effects from wireless phones RF exposures. However,  
none ofthe studies can answer questions about long-term  
exposures, since the average period of phone use in these  
studies was around three years.  
What research is needed to decide whether RF exposure  
from wireless phones poses a health risk?  
A combination oflaboratory studies and epidemiological  
studies of people actually using wireless phones would  
providesomeofthe data that areneeded. Lifetimeanimal  
exposure studies could be completed in a few years.  
However, very large numbers of animals would be  
needed to provide reliable proof of a cancer promoting  
effect if one exists. Epidemiological studies can provide  
data that is directly applicable to human populations,but  
ten or more years' follow-up may be needed to provide  
answers about some health effects, such as cancer. This is  
because the interval between the time of exposure to a  
cancer-causing agent and the time tumors develop - if  
they do -may be many, many years. The interpretation of  
epidemiological studies is hampered by difficulties in  
164  
Consumer Information on Wireless Phones  
measuring actual RF exposure during day-to-day use of  
wireless phones. Many factors affect this measurement,  
such as the angle at which the phone is held, or which  
model of phone is used.  
What is FDA doing to find out more about the possible  
health effects of wireless phone RF?  
FDA is working with the U.S. National Toxicology  
Program and with groups of investigators around the  
world to ensure that high priority animal studies are  
conducted to address important questions about the  
effects of exposure to radio frequency energy (RF).  
FDA has been a leading participant in the World Health  
Organization internationalElectromagneticFields(EMF)  
Project since its inception in 1996. An influential result of  
this work has been the development of a detailed agenda  
ofresearch needsthathasdriven theestablishmentofnew  
research programsaround theworld. TheProjecthasalso  
helped develop a seriesofpublicinformation documents  
on EMF issues.  
FDA and Cellular Telecommunications & Internet  
Association (CTIA) have a formal Cooperative Research  
and Development Agreement (CRADA) to do research  
on wireless phone safety. FDA provides the scientific  
oversight, obtaining input from experts in government,  
industry, and academic organizations. CTIA-funded  
research is conducted through contracts to independent  
investigators. The initial research will include both  
laboratory studies and studies of wireless phone users.  
The CRADA will also include a broad assessment of  
additional research needs in the context of the latest  
research developments around the world.  
Section 13: Health and Safety Information  
165  
What steps can I take to reduce my exposure to radio  
frequency energy from my wireless phone?  
If there is a risk from these products - and at this point we  
do not know that there is - it is probably very small. But  
if you are concerned about avoiding even potential risks,  
you can take a few simple steps to minimize your  
exposure to radio frequency energy (RF). Since time is a  
key factor in how much exposure a person receives,  
reducing the amount oftime spent using a wireless phone  
will reduce RF exposure.  
"If you must conduct extended conversations by wireless phone  
every day, you could place more distance between your body  
and the source of the RF, since the exposure level drops off  
dramatically with distance. For example, you could use a  
headset and carry the wireless phone away from your body or  
use a wireless phone connected to a remote antenna.  
Again,thescientificdata do notdemonstratethatwireless  
phonesareharmful. But ifyou areconcerned about theRF  
exposure from these products, you can use measures like  
those described above to reduce your RF exposure from  
wireless phone use.  
What about children using wireless phones?  
The scientificevidence does not show a danger to users of  
wireless phones,including children and teenagers. Ifyou  
want to take steps to lower exposure to radio frequency  
energy (RF), the measures described above would apply  
to children and teenagers using wireless phones.  
Reducing the time of wireless phone use and increasing  
the distance between the user and the RF source will  
reduce RF exposure.  
166  
Consumer Information on Wireless Phones  
Some groups sponsored by other national governments  
have advised that children be discouraged from using  
wi re l es s ph on es at a l l. Fo r e xa mpl e, t he g o ve rnm ent i n t he  
United Kingdom distributed leaflets containing such a  
recommendation in December 2000. They noted that no  
evidence exists that using a wireless phone causes brain  
tumors or other ill effects. Their recommendation to limit  
wireless phone use by children was strictly  
precautionary;it wasnot based on scientificevidencethat  
any health hazard exists.  
Do hands-free kits for wireless phones reduce  
risks from exposure to RF emissions?  
Since there are no known risks from exposure to RF  
emissions from wireless phones, there is no reason to  
believe that hands-free kits reduce risks. Hands-free kits  
can be used with wireless phones for convenience and  
comfort. These systems reduce the absorption of RF  
energy in thehead because thephone,which is thesource  
of the RF emissions, will not be placed against the head.  
On the other hand, if the phone is mounted against the  
waist or other part of the body during use, then that part  
of the body will absorb more RF energy. Wireless phones  
marketed in the U.S. are required to meet safety  
requirementsregardlessofwhether they areused against  
the head or against the body. Either configuration should  
result in compliance with the safety limit.  
Do wireless phone accessories that claim to shield  
the head from RF radiation work?  
Since there are no known risks from exposure to RF  
emissions from wireless phones, there is no reason to  
Section 13: Health and Safety Information  
167  
believe that accessories that claim to shield the head from  
thoseemissions reduce risks. Someproducts that claim to  
shield the user from RF absorption use special phone  
cases, while others involve nothing more than a metallic  
accessory attached to the phone. Studies have shown that  
these products generally do not work as advertised.  
Unlike "hand-free" kits, these so-called "shields" may  
interfere with proper operation of the phone. The phone  
may be forced to boost its power to compensate, leading  
to an increase in RF absorption. In February 2002, the  
Federaltrade Commission (FTC)charged two companies  
that sold devices that claimed to protect wireless phone  
users from radiation with making false and  
unsubstantiated claims. According to FTC, these  
defendants lacked a reasonable basis to substantiate their  
claim.  
What about wireless phone interference with  
medical equipment?  
Radio frequency energy (RF) from wireless phones can  
interact with some electronic devices. For this reason,  
FDA helped develop a detailed test method to measure  
electromagnetic interference (EMI) of implanted cardiac  
pacemakers and defibrillators from wireless telephones.  
This test method is now part of a standard sponsored by  
the Association for the Advancement of Medical  
instrumentation (AAMI). The final draft, a joint effort by  
FDA, medical device manufacturers, and many other  
groups, was completed in late 2000. This standard will  
allow manufacturers to ensure that cardiac pacemakers  
and defibrillators are safe from wireless phone EMI. FDA  
has tested wireless phones and helped develop a  
168  
Consumer Information on Wireless Phones  
voluntary standard sponsored by the Institute of  
Electrical and ElectronicEngineers (IEEE). This standard  
specifies test methods and performance requirements for  
hearing aids and wireless phones so that no interference  
occurs when a person uses a compatible phone and a  
compatible hearing aid at the same time. This standard  
was approved by the IEEE in 2000.  
FDA continues to monitor the use of wireless phones for  
possible interactions with other medical devices. Should  
harmfulinterference be found to occur,FDA willconduct  
testing to assess the interference and work to resolve the  
problem.  
Additional information on the safety of RF exposures  
from various sources can be obtained from the following  
organizations:  
FCC RF Safety Program:  
http://www.fcc.gov/oet/rfsafety/  
Environmental Protection Agency (EPA):  
http://www.epa.gov/radiation/  
Occupational Safety and Health Administration's (OSHA):  
http://www.osha.slc.gov/SLTC/radiofrequencyradiation/  
index.html  
National institute for Occupational Safety and Health (NIOSH):  
http://www.cdc.gov/niosh/emfpg.html  
World health Organization (WHO):  
http://www.who.int/peh-emf/  
International Commission on Non-Ionizing Radiation Protection:  
http://www.icnirp.de  
National Radiation Protection Board (UK):  
http://www.nrpb.org.uk  
Section 13: Health and Safety Information  
169  
Updated 4/3/2002: US food and Drug Administration  
http://www.fda.gov/cellphones  
Road Safety  
Your wireless phone gives you the powerful ability to  
communicateby voice,almost anywhere,anytime.But an  
important responsibility accompanies the benefits of  
wireless phones, one that every user must uphold.  
When driving a car, driving is your first responsibility.  
When using your wireless phone behind the wheel of a  
car, practice good common sense and remember the  
following tips:  
1. Get to know your wireless phone and its features, such  
as speed dial and redial. If available, these features help  
you to place your call without taking your attention off  
the road.  
2. When available, use a hands-free device. If possible, add  
an additional layer of convenience and safety to your  
wireless phone with one of the many hands free  
accessories available today.  
3. Position your wireless phone within easy reach. Be able  
to access your wireless phone without removing your  
eyes from the road. If you get an incoming call at an  
inconvenient time, let your voice mail answer it for you.  
4. Let the person you are speaking with know you are  
driving; if necessary, suspend the call in heavy traffic or  
hazardous weather conditions. Rain, sleet, snow, ice and  
even heavy traffic can be hazardous.  
170  
 
Road Safety  
5. Do not take notes or look up phone numbers while  
driving. Jotting down a "to do" list or flipping through  
your address book takes attention away from your  
primary responsibility, driving safely.  
6. Dial sensibly and assess the traffic; if possible, place  
calls when you are not moving or before pulling into  
traffic. Try to plan calls when your car will be stationary.  
If you need to make a call while moving, dial only a few  
numbers, check the road and your mirrors, then  
continue.  
7. Do not engage in stressful or emotional conversations  
that may be distracting. Make people you are talking  
with aware you are driving and suspend conversations  
that have the potential to divert your attention from the  
road.  
8. Use your wireless phone to call for help. Dial 9-1-1 or  
other local emergeny number in the case of fire, traffic  
accident or medical emergencies. Remember, it is a free  
call on your wireless phone!  
9. Use your wireless phone to help others in emergencies.  
If you see an auto accident, crime in progress or other  
serious emergency where lives are in danger, call 9-1-1  
or other local emergency number, as you would want  
others to do for you.  
10. Call roadside assistance or a special non-emergency  
wireless assistance number when necessary. If you see  
a broken-down vehicle posing no serious hazard, a  
broken traffic signal, a minor traffic accident where no  
Section 13: Health and Safety Information  
171  
one appears injured, or a vehicle you know to be stolen,  
call roadside assistance or other special non-emergency  
number.  
"The wireless industry reminds you to use your phone safely  
when driving."  
For moreinformation,pleasecall1-888-901-SAFE,or visit  
our web-site www.wow-com.com  
Provided by the Cellular Telecommunications & Internet  
Association  
Operating Environment  
Remember to follow any special regulations in force in  
any area  
and always switch your phone off whenever it is  
forbidden to use it, or when it may cause interference or  
danger. When connecting the phone or any accessory to  
another device, read its user's guide for detailed safety  
instructions. Do not connect incompatible products.  
Aswith other mobileradiotransmitting equipment,users  
are advised that for the satisfactory operation of the  
equipment and  
for the safety of personnel, it is recommended that the  
equipment should only be used in the normal operating  
position (held to your ear with the antenna pointing over  
your shoulder).  
UsingYourPhoneNearOtherElectronicDevices  
Most modern electronicequipmentisshielded from radio  
frequency (RF) signals. However, certain electronic  
equipment may not be shielded against the RF signals  
172  
   
Using Your Phone Near Other Electronic Devices  
from your wireless phone. Consult the manufacturer to  
discuss alternatives.  
Pacemakers  
Pacemaker manufacturers recommend that a minimum  
distance of 15 cm (6 inches) be maintained between a  
wireless phone and a pacemaker to avoid potential  
interference with the pacemaker.  
These recommendations are consistent with the  
independent research and recommendations of Wireless  
Technology Research.  
Persons with pacemakers:  
should always keep the phone more than 15 cm (6 inches) from  
their pacemaker when the phone is switched on.  
should not carry the phone in a breast pocket.  
should use the ear opposite the pacemaker to minimize  
potential interference.  
If you have any reason to suspect that interference is  
taking place, switch your phone off immediately.  
Hearing Aids  
Some digital wireless phones may interfere with some  
hearing aids. In the event of such interference, you may  
wish to consult your hearing aid manufacturer to discuss  
alternatives.  
Other Medical Devices  
Ifyou use any other personalmedicaldevices,consult the  
manufacturer of your device to determine if it is  
adequately shielded from external RF energy. Your  
physician may be able to assist you in obtaining this  
Section 13: Health and Safety Information  
173  
information. Switch your phone off in health care  
facilities when any regulations posted in these areas  
instruct you to do so. Hospitals or health care facilities  
may be using equipment that could be sensitive to  
external RF energy.  
Vehicles  
RF signals may affect improperly installed or  
inadequately shielded electronic systems in motor  
vehicles. Check with the manufacturer or its  
representative regarding your vehicle. You should also  
consult the manufacturer ofany equipment that has been  
added to your vehicle.  
Posted Facilities  
Switch your phoneoffin any facility whereposted notices  
require you to do so.  
Potentially Explosive Environments  
Switch your phone offwhen in any area with a potentially  
explosiveatmosphereand obey allsignsand instructions.  
Sparks in such areas could cause an explosion or fire  
resulting in bodily injury or even death.  
Users are advised to switch the phone off while at a  
refueling point (service station). Users are reminded of  
the need to observe restrictions on the use of radio  
equipment in fuel depots  
(fuel storage and distribution areas), chemical plants or  
where blasting operations are in progress.  
Areas with a potentially explosive atmosphere are often  
but not always clearly marked. They include below deck  
174  
 
Emergency Calls  
on boats, chemical transfer or storage facilities, vehicles  
using liquefied petroleum gas (such as propane or  
butane), areas where the air contains chemicals or  
particles, such as grain, dust or metal powders, and any  
other area where you would normally be advised to turn  
off your vehicle engine.  
Emergency Calls  
This phone,like any wireless phone, operates using radio  
signals, wireless and landline networks as well as user-  
programmed functions, which cannot guarantee  
connection in all conditions. Therefore, you should never  
rely solely on any wireless phone for essential  
communications (medical emergencies, for example).  
Remember,to makeor receiveany callsthephonemust be  
switched on and in a service area with adequate signal  
strength. Emergency calls may not be possible on all  
wireless phone networks or when certain network  
services and/ or phone features are in use. Check with  
local service providers.  
To make an emergency call:  
1. If the phone is not on, switch it on.  
2. Key in the emergency number for your present location  
(for example, 911 or other official emergency number).  
Emergency numbers vary by location.  
3. Press the  
key.  
If certain features are in use (call barring, for example),  
you may  
Section 13: Health and Safety Information  
175  
 
first need to deactivate those features before you can  
make an emergency call.Consult this document and your  
local cellular service provider.  
When making an emergency call,remember to giveallthe  
necessary information as accurately as possible.  
Remember that your phone may be the only means of  
communication at the scene of an accident; do not cut off  
the call until given permission to do so.  
Restricting Children's access to your Phone  
Your phone is not a toy. Children should not be allowed  
to play  
with it because they could hurt themselves and others,  
damage the phone or make calls that increase your phone  
bill.  
FCC Notice and Cautions  
FCC Notice  
The phone may cause TV or radio interference if used in  
close proximity to receiving equipment. The FCC can  
require you to stop using the phone if such interference  
cannot be eliminated.  
Vehicles using liquefied petroleum gas (such as propane  
or butane)must comply with the NationalFire Protection  
Standard (NFPA-58). For a copy of this standard, contact  
the National Fire Protection Association, One  
Batterymarch Park, Quincy, MA 02269, Attn: Publication  
Sales Division.  
176  
 
Other Important Safety Information  
Cautions  
Any changes or modifications to your phone not  
expressly approved in this document could void your  
warranty for this equipment, and void your authority to  
operate this equipment. Only use approved batteries,  
antennas and chargers. The use of any unauthorized  
accessories may be dangerous and void the phone  
warranty if said accessories cause damage or a defect to  
the phone.  
Although your phone is quite sturdy, it is a complex piece  
ofequipment and can bebroken.Avoid dropping,hitting,  
bending or sitting on it.  
Other Important Safety Information  
Only qualified personnel should service the phone or install the  
phone in a vehicle. Faulty installation or service may be  
dangerous and may invalidate any warranty applicable to the  
device.  
Check regularly that all wireless phone equipment in your  
vehicle is mounted and operating properly.  
Do not store or carry flammable liquids, gases or explosive  
materials in the same compartment as the phone, its parts or  
accessories.  
For vehicles equipped with an air bag, remember that an air  
bag inflates with great force. Do not place objects, including  
both installed or portable wireless equipment in the area over  
the air bag or in the air bag deployment area. If wireless  
equipment is improperly installed and the air bag inflates,  
serious injury could result.  
Switch your phone off before boarding an aircraft. The use of  
wireless phone in aircraft is illegal and may be dangerous to  
the aircraft's operation.  
Section 13: Health and Safety Information  
177  
 
Failure to observe these instructions may lead to the  
suspension or denial of telephone services to the offender, or  
legal action, or both.  
Product Performance  
Getting the Most Out of Your Signal Reception  
The quality of each call you make or receive depends on  
the signal strength in your area. Your phone informs you  
of the current signal strength by displaying a number of  
bars next to the signal strength icon. The more bars  
displayed, the stronger the signal.  
Ifyou're inside a building, being near a window may give  
you better reception.  
Understanding the Power Save Feature  
If your phone is unable to find a signal after 15 minutes of  
searching, a Power Save feature is automatically  
activated. If your phone is active, it periodically rechecks  
service availability or you can check it yourself by  
pressing any key.  
Anytime the Power Save feature is activated, a message  
displays on the screen. When a signal is found, your  
phone returns to standby mode.  
Understanding How Your Phone Operates  
Your phone is basically a radio transmitter and receiver.  
When it's turned on, it receives and transmits radio  
frequency (RF) signals. When you use your phone, the  
system handling your call controls the power level. This  
power can range from 0.006 watts to 0.2 watts in digital  
mode.  
178  
 
Availability of Various Features/Ring Tones  
Maintaining Your Phone's Peak Performance  
For the best care of your phone, only authorized  
personnel should service your phone and accessories.  
Faulty service may void the warranty.  
There are several simple guidelines to operating your  
phone properly and maintaining safe, satisfactory  
service.  
Hold the phone with the antenna raised, fully-extended and over  
your shoulder.  
Try not to hold, bend or twist the phone's antenna.  
Don't use the phone if the antenna is damaged.  
Speak directly into the phone's receiver.  
Avoid exposing your phone and accessories to rain or liquid  
spills. If your phone does get wet, immediately turn the power  
off and remove the battery. If it is inoperable, call Customer  
Care for service.  
Availability of Various Features/Ring Tones  
Many services and features are network dependent and  
may require additional subscription and/ or usage  
charges. Not allfeatures are available for purchase or use  
in all areas. Downloadable Ring Tones may be available  
at an additional cost. Other conditions and restrictions  
may apply. See your service provider for additional  
information.  
Battery Standby and Talk Time  
Standby and talk times will vary depending on phone  
usage patterns and conditions. Battery power  
Section 13: Health and Safety Information  
179  
   
consumption depends on factors such as network  
configuration, signal strength, operating temperature,  
features selected, frequency of calls, and voice, data, and  
other application usage patterns.  
Battery Precautions  
Never use any charger or battery that is damaged in any way.  
Use the battery only for its intended purpose.  
If you use the phone near the network's base station, it uses  
less power; talk and standby time are greatly affected by the  
signal strength on the cellular network and the parameters set  
by the network operator.  
Battery charging time depends on the remaining battery charge  
and the type of battery and charger used. The battery can be  
charged and discharged hundreds of times, but it will gradually  
wear out. When the operation time (talk time and standby time)  
is noticeably shorter than normal, it is time to buy a new  
battery.  
If left unused, a fully charged battery will discharge itself over  
time.  
Use only Samsung-approved batteries and recharge your  
battery only with Samsung-approved chargers. When a charger  
is not in use, disconnect it from the power source. Do not leave  
the battery connected to a charger for more than a week, since  
overcharging may shorten its life.  
Extreme temperatures will affect the charging capacity of your  
battery: it may require cooling or warming first.  
Do not leave the battery in hot or cold places, such as in a car in  
summer or winter conditions, as you will reduce the capacity  
and lifetime of the battery. Always try to keep the battery at  
room temperature. A phone with a hot or cold battery may  
temporarily not work, even when the battery is fully charged.  
Li-ion batteries are particularly affected by temperatures below  
0 °C (32 °F).  
180  
 
Care and Maintenance  
Do not short-circuit the battery. Accidental short- circuiting can  
occur when a metallic object (coin, clip or pen) causes a direct  
connection between the + and - terminals of the battery (metal  
strips on the battery), for example when you carry a spare  
battery in a pocket or bag. Short-circuiting the terminals may  
damage the battery or the object causing the short-circuiting.  
Dispose of used batteries in accordance with local regulations.  
In some areas, the disposal of batteries in household or  
business trash may be prohibited. For safe disposal options for  
Li-ion batteries, contact your nearest Samsung authorized  
service center. Always recycle. Do not dispose of batteries in a  
fire.  
Care and Maintenance  
Your phone is a product of superior design and  
craftsmanship and should be treated with care. The  
suggestions below will help you fulfill any warranty  
obligations and allow you to enjoy this product for many  
years  
Keep the phone and all its parts and accessories out of the  
reach of small children's.  
Keep the phone dry. Precipitation, humidity and liquids contain  
minerals that will corrode electronic circuits.  
Do not use the phone with a wet hand. Doing so may cause an  
electric shock to you or damage to the phone.  
Do not use or store the phone in dusty, dirty areas, as its  
moving parts may be damaged.  
Do not store the phone in hot areas. High temperatures can  
shorten the life of electronic devices, damage batteries, and  
warp or melt certain plastics.  
Do not store the phone in cold areas. When the phone warms  
up to its normal operating temperature, moisture can form  
inside the phone, which may damage the phone's electronic  
circuit boards.  
Section 13: Health and Safety Information  
181  
 
Do not drop, knock or shake the phone. Rough handling can  
break internal circuit boards.  
Do not use harsh chemicals, cleaning solvents or strong  
detergents to clean the phone. Wipe it with a soft cloth slightly  
dampened in a mild soap-and-water solution.  
Do not paint the phone. Paint can clog the device's moving  
parts and prevent proper operation.  
Do not put the phone in or on heating devices, such as a  
microwave oven, a stove or a radiator. The phone may explode  
when overheated.  
Use only the supplied or an approved replacement antenna.  
Unauthorized antennas or modified accessories may damage  
the phone and violate regulations governing radio devices.  
If the phone, battery, charger or any accessory is not working  
properly, take it to your nearest qualified service facility. The  
personnel there will assist you, and if necessary, arrange for  
service.  
182  
Section 14: Warranty Information  
Topics Covered  
Standard Limited Warranty  
Section 14: Warranty Information  
183  
   
Standard Limited Warranty  
What is Covered and For How Long? SAMSUNG  
TELECOMMUNICATIONS AMERICA, L.P.  
("SAMSUNG") warrants to the original purchaser  
("Purchaser") that SAMSUNG's Phones and accessories  
("Products") are free from defects in material and  
workmanship under normal use and service for the  
period commencing upon the date of purchase and  
continuing for the following specified period oftime after  
that date:  
Phone  
1 Year  
Batteries  
1 Year  
Leather Case/ Pouch  
Holster  
90 Days  
90 Days  
Other Phone Accessories 1 Year  
WhatisNotCovered?This Limited Warranty is conditioned  
upon proper use of Product by Purchaser. This Limited  
Warranty does not cover: (a) defects or damage resulting  
from accident, misuse, abuse, neglect, unusual physical,  
electrical or electromechanical stress, or modification of  
any part of Product, including antenna, or cosmetic  
damage; (b) equipment that has the serial number  
removed or made illegible; (c) any plastic surfaces or  
other externally exposed parts that are scratched or  
damaged due to normal use; (d) malfunctions resulting  
from the use of Product in conjunction with accessories,  
184  
   
Standard Limited Warranty  
products, or ancillary/ peripheral equipment not  
furnished or approved by SAMSUNG; (e) defects or  
damage from improper testing, operation, maintenance,  
installation, or adjustment; (f) installation, maintenance,  
and service of Product, or (g) Product used or purchased  
outside the United States or Canada. This Limited  
Warranty covers batteries only if battery capacity falls  
below 80% of rated capacity or the battery leaks, and this  
Limited Warranty does not cover any battery if (i) the  
battery has been charged by a battery charger not  
specified or approved by SAMSUNG for charging the  
battery, (ii) any of the seals on the battery are broken or  
show evidence of tampering, or (iii) the battery has been  
used in equipment other than the SAMSUNG phone for  
which it is specified.  
What are SAMSUNG's Obligations? During the applicable  
warranty period, SAMSUNG will repair or replace, at  
SAMSUNG's sole option, without charge to Purchaser,  
any defective component part of Product. To obtain  
service under this Limited Warranty, Purchaser must  
return Product to an authorized phone service facility in  
an adequate container for shipping, accompanied by  
Purchaser's sales receipt or comparable substitute proof  
ofsale showing the date ofpurchase, the serial number of  
Product and the sellers' name and address. To obtain  
assistance on where to deliver the Product, call Samsung  
Customer Care at 1-888-987-4357. Upon receipt,  
SAMSUNG will promptly repair or replace the defective  
Product. SAMSUNG may, at SAMSUNG's sole option,  
use rebuilt, reconditioned, or new parts or components  
when repairing any Product or replace Product with a  
rebuilt, reconditioned or new Product. Repaired/  
Section 14: Warranty Information  
185  
replaced leather cases, pouches and holsters will be  
warranted for a period of ninety (90) days. All other  
repaired/ replaced Product willbewarranted for a period  
equal to the remainder of the original Limited Warranty  
on theoriginalProduct or for 90days,whichever islonger.  
All replaced parts, components, boards and equipment  
shall become the property of SAMSUNG. If SAMSUNG  
determines that any Product is not covered by this  
Limited Warranty, Purchaser must pay all parts,  
shipping,and labor chargesfor therepair or return ofsuch  
Product.  
WHAT ARE THE LIMITS ON SAMSUNG'S WARRANTY/LIABILITY?  
EXCEPTASSETFORTH IN THEEXPRESSWARRANTY  
CONTAINED HEREIN, PURCHASER TAKES THE  
PRODUCT "AS IS," AND SAMSUNG MAKES NO  
WARRANTY OR REPRESENTATION AND THERE  
ARE NO CONDITIONS, EXPRESS OR IMPLIED,  
STATUTORY OR OTHERWISE, OF ANY KIND  
WHATSOEVER WITH RESPECT TO THE PRODUCT,  
INCLUDING BUT NOT LIMITED TO:  
"THE MERCHANTABILITY OF THE PRODUCT OR ITS FITNESS  
FOR ANY PARTICULAR PURPOSE OR USE;  
"WARRANTIES OF TITLE OR NON-INFRINGEMENT;  
"DESIGN, CONDITION, QUALITY, OR PERFORMANCE OF THE  
PRODUCT;  
"THE WORKMANSHIP OF THE PRODUCT OR THE COMPONENTS  
CONTAINED THEREIN; OR  
"COMPLIANCE OF THE PRODUCT WITH THE REQUIREMENTS OF  
ANY LAW, RULE, SPECIFICATION OR CONTRACT PERTAINING  
THERETO.  
186  
Standard Limited Warranty  
NOTHING CONTAINED IN THE INSTRUCTION  
MANUAL SHALL BE CONSTRUED TO CREATE AN  
EXPRESS WARRANTY OF ANY KIND WHATSOEVER  
WITH RESPECT TO THE PRODUCT. ALL IMPLIED  
WARRANTIES AND CONDITIONS THAT MAY ARISE  
BY OPERATION OF LAW, INCLUDING IF  
APPLICABLE THE IMPLIED WARRANTIES OF  
MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, ARE HEREBY LIMITED TO  
THE SAME DURATION OF TIME AS THE EXPRESS  
WRITTEN WARRANTY STATED HEREIN. SOME  
STATES/ PROVINCES DO NOT ALLOW  
LIMITATIONS ON HOW LONG AN IMPLIED  
WARRANTY LASTS, SO THE ABOVE LIMITATION  
MAYNOTAPPLYTO YOU.IN ADDITION,SAMSUNG  
SHALLNOTBELIABLEFORANYDAMAGESOFANY  
KIND  
RESULTING FROM THEPURCHASE,USE,ORMISUSE  
OF, OR INABILITY TO USE THE PRODUCT OR  
ARISING DIRECTLYORINDIRECTLYFROM THEUSE  
OR LOSS OF USE OF THE PRODUCT OR FROM THE  
BREACH OFTHEEXPRESSWARRANTY,INCLUDING  
INCIDENTAL, SPECIAL, CONSEQUENTIAL OR  
SIMILAR DAMAGES, OR LOSS OF ANTICIPATED  
PROFITS OR BENEFITS, OR FOR DAMAGES ARISING  
FROM ANY TORT (INCLUDING NEGLIGENCE OR  
GROSS NEGLIGENCE) OR FAULT COMMITTED BY  
SAMSUNG, ITS AGENTS OR EMPLOYEES, OR FOR  
ANY BREACH OF CONTRACT OR FOR ANY CLAIM  
BROUGHT AGAINST PURCHASER BY ANY OTHER  
PARTY. SOME STATES/ PROVINCES DO NOT  
ALLOW THE EXCLUSION OR LIMITATION OF  
Section 14: Warranty Information  
187  
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO  
THE ABOVE LIMITATION OR EXCLUSION MAY NOT  
APPLY TO YOU. THIS WARRANTY GIVES YOU  
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO  
HAVE OTHER RIGHTS, WHICH VARY FROM STATE  
TO STATE/ PROVINCE TO PROVINCE. THISLIMITED  
WARRANTY SHALL NOT EXTEND TO ANYONE  
OTHER THAN THEORIGINALPURCHASEROF THIS  
PRODUCT AND STATES PURCHASER'S EXCLUSIVE  
REMEDY. IF ANY PORTION OF THIS LIMITED  
WARRANTY IS HELD ILLEGAL OR  
UNENFORCEABLE BY REASON OF ANY LAW, SUCH  
PARTIAL ILLEGALITY OR UNENFORCEABILITY  
SHALL NOT AFFECT THE ENFORCEABILITY FOR  
THE REMAINDER OF THIS LIMITED WARRANTY  
WHICH PURCHASER ACKNOWLEDGES IS AND  
WILL ALWAYS BE CONSTRUED TO BE LIMITED BY  
ITS TERMS OR AS LIMITED AS THE LAW PERMITS.  
THE PARTIES UNDERSTAND THAT THE  
PURCHASER MAY USE THIRD-PARTY SOFTWARE  
OR EQUIPMENT IN CONJUNCTION WITH THE  
PRODUCT. SAMSUNG MAKES NO WARRANTIES OR  
REPRESENTATIONS AND THERE ARE NO  
CONDITIONS, EXPRESS OR IMPLIED, STATUTORY  
OR OTHERWISE, AS TO THE QUALITY,  
CAPABILITIES, OPERATIONS, PERFORMANCE OR  
SUITABILITY OF ANY THIRDPARTY SOFTWARE OR  
EQUIPMENT, WHETHER SUCH THIRD-PARTY  
SOFTWARE OR EQUIPMENT IS INCLUDED WITH  
THE PRODUCT DISTRIBUTED BY SAMSUNG OR  
OTHERWISE, INCLUDING THE ABILITY TO  
INTEGRATEANYSUCH SOFTWAREOREQUIPMENT  
188  
Standard Limited Warranty  
WITH THEPRODUCT. THEQUALITY, CAPABILITIES,  
OPERATIONS, PERFORMANCE AND SUITABILITY  
OF ANY SUCH THIRD-PARTY SOFTWARE OR  
EQUIPMENT LIE SOLELY WITH THE PURCHASER  
AND THE DIRECT VENDOR, OWNER OR SUPPLIER  
OF SUCH THIRD-PARTY SOFTWARE OR  
EQUIPMENT, AS THE CASE MAY BE.  
This Limited Warranty allocates risk of Product failure  
between Purchaser and SAMSUNG, and SAMSUNG's  
Product pricing reflects this allocation of risk and the  
limitations of liability contained in this Limited  
Warranty. The agents, employees, distributors, and  
dealers of SAMSUNG are not authorized to make  
modifications to this Limited Warranty, or make  
additional warranties binding on SAMSUNG.  
Accordingly, additional statements such as dealer  
advertising or presentation, whether oral or written, do  
not constitute warranties by SAMSUNG and should not  
be relied upon.  
Samsung Telecommunications America, L.P.  
1301 East Lookout Drive  
Richardson, Texas 75082  
Phone: 1-800-SAMSUNG  
Phone: 1-888-987-HELP (4357)  
©2005Samsung Telecommunications America.Allrights  
reserved.  
No reproduction in whole or in part allowed without  
prior  
Section 14: Warranty Information  
189  
written approval. Specifications and availability subject  
to change without notice.  
Intellectual Property Statement  
All Intellectual Property, as defined below, owned by or  
which is otherwise the property of Samsung or its  
respective suppliers relating to the SAMSUNG Phone,  
including but not limited to, accessories, parts, or  
software relating thereto (the "Phone System"), is  
proprietary to Samsung and protected under federal  
laws, state laws, and international treaty provisions.  
Intellectual Property includes, but is not limited to,  
inventions (patentable or unpatentable), patents, trade  
secrets, copyrights, software, computer programs, and  
related documentation and other works of authorship.  
You may not infringe or otherwise violate the rights  
secured by the Intellectual Property. Moreover,you agree  
that you willnot (and willnot attempt to)modify,prepare  
derivative works of, reverse engineer, decompile,  
disassemble, or otherwise attempt to create source code  
from the software. No title to or ownership in the  
Intellectual Property is transferred to you. All applicable  
rights of the Intellectual Property shall remain with  
SAMSUNG and its suppliers.  
190  
 
Samsung Telecommunications America (STA), L.P.  
Samsung Telecommunications America (STA),  
L.P.  
Internet Address: http://www.samsungusa.com  
©2005Samsung TelecommunicationsAmerica.Samsung  
is a registered trademark of Samsung Electronics  
America, Inc. and its related entities.  
Printed in South Korea  
GH68-06772A  
Openwave® is a registered Trademark ofOpenwave, Inc.  
RSA® is a registered Trademark RSA Security, Inc.  
Headquarters  
Customer Care Center  
,
1301 East Lookout Dr.  
Richardson, TX 75082  
Tel: 972.761.7000  
1601 E. Plano Parkway  
Suite 150  
Plano, TX 75074  
Toll Free Tel:  
1.888.987.HELP (4357)  
Section 14: Warranty Information  
191  
 
192  
Creating and Sending New  
Messages 84  
Index  
D
A
Dialing a Number  
Address Book 72  
SIM Card 73  
Add New Words to T9  
Dictionary 61  
Address Book 65  
Searching for a Number  
Display  
backlight 22  
icons 21  
Alphabet mode 58  
B
Display Settings  
Back Light 104  
Brightness Control 104  
Menu Style 104  
Wallpaper 103  
Backlight  
description 22  
Battery  
E
charging 12  
installing 12  
low indicator 13  
removing 10  
Entering Text 57  
Changing the Text Entry  
Mode 58  
Using Alphabet Mode 61  
Using Numbers 63  
Using Symbols 63  
Using T9 Mode 60  
C
Call Functions 23  
Adjusting the Call  
Volume 26  
External Display 22  
Answering a Call 26  
Call Log 27  
Correcting the  
Number 24  
Making a Call 24  
Redialing Last  
Number 24  
F
Functions and Options 32  
G
Games  
Memory Status 155  
My Games 154  
Settings 154  
Silent Mode 32  
Call Waiting 37  
Charging battery 12  
Create 84  
Shop Games 154  
Getting Started 9  
Activating Your Phone 10  
193  
 
Voicemail 15  
Number mode 58  
O
H
Health and Safety  
Information 157  
I
Icons, description 21  
Instant Messenger 82  
International Call 24  
L
Low battery indicator 13  
M
Making a Call  
Address Book 25  
On/off switch, phone 14  
Options  
During a Call 34  
Putting a Call on Hold 34  
Own Number 76  
P
Personal Organizer 125  
Phone  
icons 21  
switching on/off 14  
Phone Settings 101  
R
Menu Navigation 41  
Menu Outline 45  
Recent Calls 27  
Call Time 31  
Messaging 81  
Multimedia Files  
Downloading 121  
Data Call Time 31  
Data Volume 31  
Delete All 30  
Multimedia Message  
Creating and Sending 89  
Viewing Calls Made 29  
Viewing Calls  
Received 28  
Viewing Missed Calls 27  
Voice Mail 30  
Multi-Party Call 37  
Dropping One  
Participant 39  
Private Conversation 38  
Record Audio 139  
S
Setting Alarms 126  
Mute 35  
N
Network Services 147, 148  
Call Forwarding 148  
Call Waiting 149  
Settings 99  
Display Settings 103  
Resetting Your  
Caller ID 152  
Phone 112  
Network Selection 151  
Security Settings 109  
194  
Sound Settings 105  
Understanding Your  
Shortcuts 42  
SIM card  
Phone 17  
Features of Your  
installing 10  
Phone 18  
Front View of Your  
Phone 19  
Skin 104  
Soft Keys 32  
Speed Dial  
Edit List 74  
Using Organizer 128  
Using the Calculator 138  
Using the Timer 144  
V
Setting Up Entries 73  
Standard Limited  
Warranty  
Voice Mail 15  
Standard Limited  
changing number 16  
Warranty 184  
W
WAP 115  
Warranty Information 183  
Switching on/off  
phone 14  
T
T9 mode 58  
Text Input Mode  
Changing 59  
Text Messages 83  
Time & Date 100  
Travel adapter 12  
U
Understanding Your  
Address Book  
Editing an Existing  
Address Book Entry 72  
Finding an Address book  
Entry 71  
195  
196  

Sony Ericsson T280I User Manual
Sony CDX 3100 User Manual
Seagate MOMENTUS ST92011A User Manual
Samsung SII User Manual
Samsung SGH X820 User Manual
Samsung SGH A701 User Manual
Samsung GT S6102 User Manual
Salton FSCM200BM FSCM200M FSCM200RM FSCM200CBM User Manual
Philips AAJ3540 User Manual
Panasonic FP2 User Manual