User Guide
Samsung Telecommunications America
1301 East Lookout Drive
Richardson, Texas 75082
1-800-SAMSUNG
www.samsungwireless.com
© 2004 Samsung Telecommunications America. Samsung is a registered
trademark of Samsung Electronics America, Inc. and its related entities.
Specifications subject to change without notice.
GH68-05083A
05/2004. Rev.1.0
DUAL BAND GPRS Series
SGH-e316
Portable Digital Telephone
User Manual
Please read this manual before operating your phone,
and keep it for future reference.
Printed in Korea
Code No.: GH68-05083A
English.05/2004. Rev. 1.0
Intellectual Property
All Intellectual Property, as defined below, owned by or which is
otherwise the property of Samsung or its respective suppliers
relating to the SAMSUNG Phone, including but not limited to,
accessories, parts, or software relating thereto (the “Phone
System”), is proprietary to Samsung and protected under
federal laws, state laws, and international treaty provisions.
Intellectual Property includes, but is not limited to, inventions
(patentable or unpatentable), patents, trade secrets,
copyrights, software, computer programs, and related
documentation and other works of authorship. You may not
infringe or otherwise violate the rights secured by the
Intellectual Property. Moreover, you agree that you will not (and
will not attempt to) modify, prepare derivative works of, reverse
engineer, decompile, disassemble, or otherwise attempt to
create source code from the software. No title to or ownership
in the Intellectual Property is transferred to you. All applicable
rights of the Intellectual Property shall remain with SAMSUNG
and its suppliers.
Samsung Telecommunications America,
L.P.
U. S. Headquarters:
1301 East Lookout Drive
Richardson, TX 75082
Tel: 972-761-7000
Fax: 972-761-7001
Customer Care Center:
1601 E. Plano Parkway
Suite 150
Plano, TX 75047
Tel: 888-987-HELP (4357)
Fax: 972-761-7501
Internet Address: http://www.samsungusa.com/
wireless
©2004 Samsung Telecommunications America, L.P. All rights
reserved. No reproduction in whole or in part allowed without
prior written approval. Samsung is a registered trademark of
Samsung Electronics America, Inc. and its related entities.
Table of Contents
Table of Contents
1
Table of Contents
2
Table of Contents
3
Table of Contents
4
Acknowledging Special Precautions and the FCC and Indus-
try Canada Notice ................................................ 175
Appendix B: Guide to Safe and Responsible Wireless Phone
Use.................................................................... 178
Table of Contents
5
Table of Contents
6
Important Safety Precautions
Read these guidelines before using your wireless
phone. Failure to comply with them may be
dangerous or illegal.
Road Safety at All Times
Do not use a hand-held phone while driving; park the
vehicle first.
Switching Off When Refueling
Do not use the phone at a refueling point (service
station) or near fuels or chemicals.
Switching Off in an Aircraft
Wireless phones can cause interference. Using them
in an aircraft is both illegal and dangerous.
Switching Off in Hospitals
Switch your phone off near medical equipment.
Follow any regulations or rules in force.
Interference
All wireless phones may be subject to interference,
which could affect their performance.
Special Regulations
Follow any special regulations in force in any area
and always switch your phone off whenever it is
Important Safety Precautions
7
forbidden to use it, or when it may cause
interference or danger (in a hospital for example).
Sensible Use
Use only in the normal position (held to the ear).
Avoid unnecessary contact with the antenna when
the phone is switched on.
Emergency Call
Ensure the phone is switched on and in service. Key in
the emergency number for your present location,
then press the
key. You must deactivate any
unnecessary features before you can make an
emergency call. Give all the necessary information
as accurately as possible. Do not end the call until
given permission to do so.
Water Resistance
Your phone is not water-resistant. Keep it dry.
Accessories and Batteries
Use only Samsung-approved accessories and
batteries. Use of any unauthorized accessories could
damage your phone and may be dangerous.
Qualified Service
Only qualified service personnel may repair your
phone.
For more detailed safety information, see “Health
Important Safety Precautions
8
Unpacking
Your package contains the following items:
Handset
Travel Charger
Battery
Ear-microphone
User’s Manual
Note: The items supplied with your phone may be different, depending upon
your country or service provider.
You can obtain the following accessories for your
phone from your local Samsung dealer:
Standard battery
Simple hands-free kit
Car power charger
Travel charger
Ear-microphone
Car holder
Battery charger
Data kit
Unpacking
9
Unpacking
10
Your Phone
Phone Layout
The following illustrations show the main elements of
your phone:
menu exit key
Your Phone
11
Ear-microphone
jack
Antenna
Camera
Camera key
Service light
External display
Service light
Key(s)
Description
In Menu mode, scrolls through the menu
options and Phone Book.
In Idle mode, the Up key allows you to access
the Camera menu and the Down key to access
your favorite menu option directly. For further
details about shortcuts, see “Using Shortcuts”
In Menu mode, the Left key returns to the
previous menu level and the Right key selects
the current menu.
When entering text, moves the cursor to the
left and right respectively.
In Idle mode, allows you to access your
favorite menu options directly. For further
details about shortcuts, see “Using Shortcuts”
Your Phone
12
Key(s)
Description (Continued)
Performs the functions indicated by the text
above them, on the bottom line of the display.
(soft keys)
In Idle mode, launches the WAP (Wireless
Application Protocol) browser.
Makes or answers a call.
In Idle mode, recalls the last number dialed,
received or missed.
In Menu mode, selects a menu function or
stores information that you have entered, such
as a name in the SIM card or phone’s memory.
Ends a call. Also switches the phone on and
off when held down.
In Menu mode, cancels your input and returns
to Idle mode.
In the text Input mode, deletes characters from
the display.
In Menu mode, returns to the previous menu
level.
In Idle mode, quickly accesses your voice mail
when held down.
Enters numbers, letters and some special
characters.
Your Phone
13
Key(s)
Description (Continued)
Enters special characters.
Performs various functions.
(on the right side of the phone)
In Standby mode, turns the camera on when held
down.
In Capture mode, works as a camera shutter.
(on the left side of the phone)
During a call, adjusts the earpiece volume.
In Idle mode with the folder open, adjusts the
keypad tone volume. With the folder closed,
turns the external display on when held down.
In Menu mode, scrolls through the menu
options and Phone Book.
Your Phone
14
Icons
Icon
Description
Shows the received signal strength. The greater
the number of bars, the stronger the signal.
Appears when a call is in progress.
Appears when you are out of your service area.
When it displays, you cannot make or receive a
call.
Appears when you are connected to the GPRS
network.
Appears when the GPRS data connection is
established.
Appears when you are out of your home area and
have logged onto a different network; for example,
when traveling in other countries.
Appears when a new text message has been
received.
Appears when a new multimedia message has
been received.
Appears when the Call Forwarding feature is
activated.
Appears when a new voice mail message has
been received.
Your Phone
16
Icon
Description (Continued)
Appears when you set an alarm to ring at a
specified time.
Appears when Silent mode is active or when you
set the Alert Type menu (Menu 5.3) to Vibration.
respectively.
Appears when Mute mode is active.
Shows the level of your battery. The more bars
you see, the more power you have remaining.
Backlight
The backlight illuminates the display and the keypad.
When you press any key or open the folder, the
backlight turns on and remains on for a given period
of time, depending on your setting in the Back Light
menu (Menu 6.1.4). When no keys are pressed, the
display dims and turns off after one minute to
conserve your battery power.
To specify the length of time the backlight is active,
for further details.
External Display
Your phone has an external display on the folder. It
indicates when you have an incoming call or a
message. At the specified time it also alerts you when
Your Phone
17
you have set an alarm by flashing the service light
and showing the corresponding icon on the display.
You can also select the color of an image to be
displayed in the Front LCD menu (Menu 6.1.2). See
“Front LCD” on page 118 for further details.
To turn the display on with the folder closed, press
and hold one of the Volume keys on the left side of
the phone. With the folder closed, you can take
photos using the external display by pressing the
Camera key on the right side of the phone. For
Service Light
The service light is on the folder. It flashes when
services are available on the phone.
To activate or deactivate the service light, set the
further details.
Your Phone
18
Your Phone
20
Getting Started
Installing the SIM Card
When you subscribe to a cellular network, you are
provided with a plug-in SIM card loaded with your
subscription details, such as your PIN, any optional
services available and so on.
Important! The plug-in SIM card and its contacts can
be easily damaged by scratches or bending, so be
careful when handling, inserting or removing the
card.
Keep all SIM cards out of the reach of small children.
1. If necessary, switch the phone off by holding
down the
displays.
key until the power-off image
2. Remove the battery. To do so:
Slide the battery lock towards the top of the phone
➀
and hold it in that position.
➁
Lift the battery away, as shown.
Getting Started
21
3. Slide the SIM card into the SIM card socket, as
shown, so that it locks the card into position.
Make sure the metal contacts of the card face into the
phone.
When you need to remove the SIM card, slide it upwards,
as shown, and take it out of the socket.
Getting Started
22
4. Replace the battery so that the tabs on the end
align with the slots at the bottom of the phone.
5. Press the battery down until it clicks into place.
Make sure that the battery is properly installed
before switching the power on.
Charging the Battery
Your phone is powered by a rechargeable Li-ion
battery. A travel charger comes with your phone for
charging the battery. Use only approved batteries
and chargers. Ask your local Samsung dealer for
further details.
Getting Started
23
The travel charger allows you to use the phone while
the battery is charging, but this causes the phone to
charge more slowly.
Note: You must fully charge the battery before using your phone for the first
time. A discharged battery is fully recharged in approximately 200 minutes.
1. With the battery in position on the phone, plug the
connector of the travel charger into the jack at
the bottom of the phone.
2. Plug the adapter into a standard AC wall outlet.
3. When charging is finished, unplug the adapter
from the power outlet and disconnect it from the
Getting Started
24
phone by pressing the buttons on both sides of the
connector and pulling the connector out.
Note: You must unplug the adapter before removing the battery from the phone
during charging; otherwise, the phone could be damaged.
Low Battery Indicator
When the battery is weak and only a few minutes of
talk time remain, a warning tone sounds and a
message repeats at regular intervals on the display. If
this happens, the display dims to conserve the
remaining battery power.
When the battery level becomes too low, the phone
automatically turns off.
Switching the Phone On or Off
1. Open the folder.
2. Press and hold the
switches on.
key until the phone
Getting Started
25
3. If the phone asks you to enter the phone
password, enter the password and press the OK
soft key. It is preset to “00000000” at the factory.
For further details, see page 159.
4. If the phone asks for a PIN, enter the PIN and press
The phone searches for your network and, after finding
it, the idle screen appears on the display. You can now
make or receive a call.
The display language is preset to English at the factory.
To change the language, use the Language (Menu 6.4).
5. When you wish to switch the phone off, press and
hold the
displays.
key until the power-off image
Getting Started
26
Call Functions
Making a Call
When the idle screen displays, enter the area code
and phone number, then press the
key.
Note: When you activate the Auto Redial option in the Extra Settings menu
(Menu 6.6), the phone automatically redials up to ten times when the person
details.
Making an International Call
1. Press and hold the
0
key.
The character appears.
+
2. Enter the country code, area code and phone
number and press the key.
Call Functions
27
Correcting the Number
To clear
Press the
the last digit
displayed
C key.
any other digit in Left or Right key until the cursor is
the number
immediately to the right of the digit to
be cleared. Press the C key. You can
also insert a missing digit simply by
pressing the appropriate key.
the whole
display
C key and hold it for more than one
second.
Ending a Call
When you want to end your call, briefly press the
key or close the folder.
Redialing the Last Number
The phone stores the numbers you have dialed,
received or missed if the caller is identified. See “Call
Records” on page 99 for further details.
To recall any of these numbers:
1. If you have typed characters on the display, press
the
key to return to Idle mode.
2. Press the
key to display a list of the last numbers
in the order you made, received or missed them.
Call Functions
28
3. Use the Up and Down keys to scroll through the
numbers until the number you want is highlighted.
To
Press the
dial the number
edit the number
key.
Options soft key and select
Edit. Change the number,
referring to “Correcting the
delete the
number
Options soft key and select
Delete.
delete all of the
numbers on the
Call Log list
Options soft key and select
Delete All. For further details,
Making a Call from Phone Book
You can store the phone numbers that you use
regularly in the SIM card or the phone’s memory,
which are collectively called Phone Book. Simply
select a name to recall the associated number. For
further details about the Phone Book feature, see
Adjusting the Volume
During a call, if you want to adjust the earpiece
volume, use the Volume keys on the left side of the
phone.
Call Functions
29
Press the key to increase the volume level and the
key to decrease the level.
In Idle mode, you can also adjust the keypad tone
volume using these keys.
Answering a Call
When somebody calls you, the phone rings and
displays the incoming call image.
When the caller can be identified, the caller’s phone
number or name, if stored in your Phone Book,
displays.
1. If necessary, open the folder.
2. Press the
key or the Accept soft key to answer
the incoming call.
When the Anykey Answer option in the Extra Settings
menu (Menu 6.6) is activated, you can press any key to
answer a call except for the
key and the Reject
Call Functions
30
When the Active Folder option in the Extra Settings
menu (Menu 6.6) is activated, you can answer the call
To reject the call, press and hold one of the Volume keys, or
press the Reject soft key or
key.
3. End the call by pressing the
key.
Note: You can answer a call while using Phone Book or menu features. After
ending the call, the phone returns to the function screen you were using.
Viewing Missed Calls
When you are unable to answer a call for any
reason, you can find out who called you so that you
can call the person back.
The number of calls you missed displays on the idle
screen immediately after a call is missed.
To view the missed call immediately:
1. If necessary, open the folder.
2. Press the View soft key.
The number for the most recent missed call displays, if
available.
To
Press the
scroll through the
missed calls
Up or Down key.
call the number
displayed
key.
Call Functions
31
To
Press the
edit or delete a
Select soft key. See below.
missed call number
Editing a Missed Call Number
Note: When the number for the missed call is not available, the Edit option
does not display.
1. Press the View soft key.
2. Press the Up or Down key to highlight the number
and press the Select soft key.
3. Press the Options soft key.
4. Select the Edit soft key. Enter your edits and press
the Save soft key.
5. Use the right and left soft keys to select the phone
category and press the Select soft key.
6. Choose between the SIM and Phone location
options and press the Select soft key.
7. Enter the Name or choose from the provided list
and press the OK soft key.
8. Enter the number and press the Save soft key.
For more options on this function, see “Using Phone
Call Functions
32
Deleting a Missed Call
1. Press the Options soft key.
2. If necessary, press the Up or Down key to highlight
the Delete option.
3. Press the Select soft key.
You can press the
key at any time to exit the
Missed Call feature.
Note: You can access the Missed Call feature at any time by selecting the
Quickly Switching to Silent Mode
Silent mode is convenient when you wish to stop the
phone from making noise, in a theater for example.
In Idle mode, press and hold the
key until the
“Silent Mode” message and the Vibration icon (
display.
)
In Silent mode, your phone changes the sound
settings as follows:
Option
New Setting
Alert Type (Menu 5.3)
Vibration
Off
Keypad Tone (Menu 5.4)
Message Tone (Menu 5.5) Vibration
Folder Tone (Menu 5.6)
Power On/Off (Menu 5.7)
Extra Tones (Menu 5.9)
Off
Vibration*
Off
Call Functions
33
Note: Menu 5.7 Power On/Off vibration occurs during power on not power off.
To exit and reactivate the previous sound settings,
press and hold the
key again until “Exit Silent
Mode” appears. The Vibration icon ( ) no longer
displays.
Call Functions
34
Selecting Functions and Options
Your phone offers a set of functions that allows you to
customize it. These functions are arranged in menus
and sub-menus, accessed using the two soft keys
marked
and . Each menu and sub-menu allows
you to view and alter the settings of a particular
function.
The roles of the soft keys vary according to the
function you are currently using; the labels on the
bottom line of the display just above each key
indicate its current role.
Example
:
Selecting Functions and Options
35
To view the various functions and options available
and to select the one you want:
1. Press the appropriate soft key.
To
Press the
select the:
Select soft key or the Right
• function displayed
• option highlighted
key.
view the next
function or highlight
the next option on a
list
Down key or the key on the
left side of the phone.
move back to the
previous function or
option on a list
Up key or the key on the left
side of the phone.
move back up one
level in the structure
Left key, C key or
soft key.
exit the structure
without changing the
settings
key.
In some functions, you may be asked for a password or
PIN. Enter the code and press the OK soft key.
Note: When you access a list of options, your phone highlights the current
option. If, however, there are only two options, such as On/Off or Enable/
Disable, your phone highlights the option that is not currently active so that you
can select it directly.
Selecting Functions and Options
36
Phone Book
You can store phone numbers and their
corresponding names in both your SIM card and
phone’s memory. They are physically separate but
are used as a single entity, called Phone Book.
Storing a Number with a Name
There are two ways to store a number:
♦Using the Save soft key in Idle mode
♦Using the New Entry option in the Phone Book menu
Storing a Number in Idle Mode
As soon as you start to enter a number, Save appears
above the left soft key to allow you to store the
number in Phone Book.
1. Enter the number you want to store.
Note: If you make a mistake while entering a number, correct it using the C key.
For further details, see page 28.
2. When you are sure that it is correct, press the Save
soft key.
Phone Book
37
3. Select the category of the number to be stored.
Three categories are available:
Mobile Number
Work Number
Home Number
To select the category, press the Left or Right key and
press the Select soft key.
4. Select a memory location, either SIM or Phone, by
pressing the Up or Down key and press the Select
soft key.
Note: When you change phones, any numbers stored in your SIM card
memory are automatically available with the new phone, whereas any numbers
stored in the phone’s memory must be reentered.
5. Enter a name and press the OK soft key.
For further details about entering characters, see
To
Press the
use the entry options Options soft key. For further
return to the idle
screen
key.
Phone Book
38
Storing a Number Using the Phone Book Menu
1. When the idle screen displays, press the Ph.Book
soft key.
2. Scroll to New Entry by pressing the Up or Down key
and press the Select soft key.
3. Select the category of the number to be stored by
pressing the Left or Right key, and press the Select
soft key.
Note: E-mail Address is available in this step. It allows you to save an e-mail
address instead of a phone number.
4. Select a memory location, either SIM or Phone, by
pressing the Up or Down key and press the Select
soft key.
If you are saving an e-mail address, SIM is not available.
5. Enter a name and press the OK soft key.
For further details about entering characters, see
6. Enter the number or e-mail address you want to
store and press the Save soft key.
To
Press the
use the entry options Options soft key. For further
Phone Book
39
To
Press the
return to the idle
screen
key.
Using Phone Book Entry Options
While accessing any Phone Book entry, press the
Options soft key to access the options for the entry.
To
Press the
select the
Select soft key or the Right key.
highlighted option
highlight a
different option
Up or Down key until the option you
want highlights.
The following options are available:
Paste: allows you to paste the number into the
normal dialing mode. Use this option to dial a
number similar to one in Phone Book, such as a
different extension in the same office.
Use the C key to change the number as required; see
page 28 for further details. When you are ready to
dial, press the
key.
Edit: allows you to edit the name and/or number.
Select One Entry to change the name and/or
number for the selected entry.
Select All Entry to change only the name of the entry.
Photo Caller ID: allows you to assign one of the
photos you took using the camera as a caller ID
image to be displayed when you receive a call from
Phone Book
40
the selected number. For details about the Camera
Select a Photo: allows you to select a photo for the
number.
View: displays a photo assigned to the number.
Delete: cancels the photo caller ID setting for the
number.
Delete: allows you to delete the selected number
from Phone Book. You are asked to confirm that you
wish to delete the name and number by pressing the
Yes soft key.
Copy: allows you to copy the number to another
location. You can select the memory location.
Caller Group: allows you to organize your Phone
Book entries in caller groups so that the phone alerts
you in a specific way when a person from one of your
groups calls you. Select one of the ten groups
available.
To remove an entry from a group, select the No
Group option.
For further details about how to change caller group
Add Entry: allows you to add a new number to the
currently selected name.
Dialing a Number from the Phone Book
Once you have stored phone numbers in the Phone
Book, you can dial them easily and quickly by using
the location numbers that were assigned to them in
the Phone Book.
Phone Book
41
Dialing a Number from the SIM Card
1. In Idle mode, enter the location number of the
number you want to dial and press the # key.
The list of the entries in the SIM card appears.
2. If necessary, scroll through the list using the Up or
Down key.
3. When the number displays, press the Dial soft key
or
key.
Dialing a Number from the Phone’s Memory
1. In Idle mode, press and hold the 0 key. A +
appears.
2. Enter the location number of the number you
want and press the # key.
3. The list of the entries in the phone’s memory
appears.
4. If necessary, scroll through the list using the Up or
Down key.
5. When the number displays, press the Dial soft key
or
key.
Speed Dialing
You can assign up to eight phone numbers from
Phone Book that you use most frequently to the
number keys (2 to 9), and then dial them easily
whenever you want, simply by pressing and holding
the associated number key.
Phone Book
42
Setting up Speed-dial Entries
1. When the idle screen displays, press the Ph.Book
soft key.
2. Scroll to speed dial by pressing the Up or Down key
and press the Select soft key.
3. Select a number between 2 to 9 to assign the
speed dialling number, and press the OK soft key.
Note: Memory location 1 is reserved for your Voice Mail server number.
If you have already assigned a number to the key,
the Options soft key replaces the OK soft key. Go to
step 6.
4. Select an entry from the list and press the View soft
key.
5. Press the Select soft key to save this entry in the
speed dial list.
6. When you are finished, press the
soft key or
the soft key or to edit the number use the
following options by pressing the Options soft key:
♦Change: allows you to assign a different number to
the key.
♦Delete: allows you to clear the setting so that no
number is assigned to the key.
♦Delete All: allows you to clear the settings for all
keys so that no numbers are assigned to any of the
keys.
Phone Book
43
♦Number: allows you to view the number assigned
to the key. You can dial the number by pressing the
key.
Speed-dialing from Phone Book
To speed-dial the numbers assigned to the 2 to 9
keys, press and hold the appropriate key.
Searching for and Dialing a Number in Phone Book
After storing numbers in Phone Book, you can search
for them in two ways; by name and by caller group.
Searching for a Number by Name
1. When the idle screen displays, press the Ph.Book
soft key.
2. Press the Select soft key when Search highlights.
You are asked to enter a name.
3. Enter the first few letters of the name that you
want to find. The Phone Book entries are listed,
starting with the first entry matching your input.
To
Press the
view the highlighted View soft key.
entry
select a different
entry
Up or Down key until the entry
you want highlights.
Phone Book
44
To
Press the
look for a name
starting with a
different letter
key labeled with the letter you
want.
4. Once you have found the entry, press the
key
to dial the number, or press the Options soft key to
access the Phone Book entry options; for further
details, see page 40.
Searching for a Number by Caller Group
1. When the idle screen displays, press the Ph.Book
soft key.
2. Scroll to Group Search by pressing the Up or Down
key and press the Select soft key. You are asked to
enter a group name.
3. Enter the first few letters of the group name that
you want to find. The caller groups are listed,
starting with the first group matching your input.
4. If necessary, scroll to a group by pressing the Up or
Down key and press the View soft key. The Phone
Book entries in the caller group are listed.
To
Press the
view the highlighted View soft key.
entry
Phone Book
45
To
Press the
select a different
entry
Up or Down key until the entry
you want highlights.
5. Once you have found the entry, press the
key
to dial the number, or press the Options soft key to
access the Phone Book entry options; for further
details, see page 40.
Editing a Caller Group
1. When the idle screen displays, press the Ph.Book
soft key.
2. Scroll to Group Edit by pressing the Up or Down key
and press the Select soft key.
3. Scroll through the group list by pressing the Up or
Down key.
4. When the group you want highlights, press the
Options soft key.
5. Select each option and change the settings, as
you want.
The following options are available:
♦Call Ring Tone: allows you to set a ring tone to be
used when you receive a call from a person in the
group.
♦SMS Tone: allows you to set a ring tone to be used
when you receive a message from a person in the
group.
Phone Book
46
♦Graphic: allows you to set a graphic icon to be
displayed when you receive a voice call from a
person in the group.
♦Group Name: allows you to assign a name to the
group. For further details about entering
characters, see page 51.
6. When you are finished, press the
or
key.
Speed-dialling from the SIM Card
To speed-dial the numbers saved in the SIM card:
1. Enter the location number and press the
key.
or
2. The display shows the information about the entry,
such as name, phone number and memory
location.
3. If necessary, press the Up or Down key to scroll to
the previous or next entry.
4. Press the
key or Dial soft key.
Deleting All of the Phone Book Entries
You can delete all of entries in the selected memory
or both memories.
1. When the idle screen displays, press the Ph.Book
soft key.
2. Scroll to Delete All by pressing the Up or Down key
and press the Select soft key.
Phone Book
47
3. To place a check mark by the memory you want
to empty, All, SIM or Phone, press the Mark soft
key.
You can remove the check mark by pressing the
Unmark soft key.
4. When you are finished marking, press the Delete
soft key to delete the entries in the selected
memory.
5. Enter the phone password and press the OK soft
key.
The password is preset to “00000000” at the factory. To
change this password, see page 159.
6. When a confirming message appears, press the
Yes soft key.
To cancel the deletion, press the No soft key.
7. When you are finished, press the C or
key.
Checking the Memory Status
You can check how many names and numbers are
stored in Phone Book, in both the SIM card and
phone’s memory. You can also see the capacity of
both memories.
1. When the idle screen displays, press the Ph.Book
soft key.
2. Select the Memory Status option by pressing the
Up or Down key and press the Select soft key.
Phone Book
48
3. Press the Up or Down key to view the number of
existing and total entries available in the SIM card
and phone’s memory.
4. When you are finished, press the C or
key.
Using the Service Dialing Numbers
You can view the list of Service Dialing Numbers
(SDN) assigned by your service provider. These
numbers include emergency numbers, directory
enquiries and voice mail numbers.
1. When the idle screen displays, press the Ph.Book
soft key.
2. Select the SDN option by pressing the Up or Down
key and press the Select soft key.
3. Scroll through the numbers by using the Up or
Down key.
4. To dial the number displayed, press the Dial soft
key.
Note: This option is available only when your SIM card supports Service
Dialing Numbers.
Phone Book
49
Phone Book
50
Entering Text
When using your phone, you will often need to enter
text, such as when storing a name in Phone Book,
creating your personal greeting or scheduling events
on your calendar. You can enter alphanumeric
characters by using your phone’s keypad.
Your phone has the following text input modes:
♦T9 mode
This mode allows you to enter words with only one
keystroke per letter. Each key on the keypad has
more than one letter; for example, when you press
the 5 key once, J, K or L displays. T9 mode
automatically compares your keystrokes with an
internal linguistic dictionary to determine the correct
word, thus requiring far fewer keystrokes than the
traditional Alphabet mode.
♦Alphabet mode
This mode allows you to enter letters by pressing the
key labeled with the letter you want. Press the key
once, twice, three or four times until it displays.
♦Number mode
This mode allows you to enter numbers.
♦Symbol mode
This mode allows you to enter various symbols and
special characters.
Changing the Text Input Mode
When you are in a field that allows characters to be
entered, you will notice the text input mode indicator
on the display.
Entering Text
51
Example: Writing a text message
To select
Press the right soft key until
T9 mode
Alphabet mode
Number mode
Symbol mode
the symbol list displays. See
Using T9 Mode
T9 is a predictive text input mode that allows you to
key in any character using single keystrokes. This text
input mode is based on a built-in dictionary.
To enter a word in T9 mode:
1. When you are in T9 mode, start entering a word by
pressing the 2 to 9 keys. Press each key only once
for each letter.
Entering Text
52
Example: To enter “HELLO” in T9 mode, press the 4, 3, 5, 5
and keys.
6
The word that you are typing appears on the display. It
may change with each key that you press.
2. Enter the whole word before editing or deleting
the keystrokes.
3. When the word displays correctly, go to step 4.
If not, press the
0
key or the Up or Down key repeatedly
to display alternative word choices for the keys that you
have pressed.
Example: Both “OF” and “ME” use the
6
and
3
keys. The
phone displays the most commonly used choice first.
4. Insert a space by pressing the
entering the next word.
key and start
To add a new word into the T9 dictionary:
1. After pressing the keys corresponding to the word
you want to add, press the 0 or Down key to
display the alternative words.
2. When you press the 0 or Down key on the last
alternative word, the display shows Add on the
bottom line. Press the Add soft key.
3. If necessary, clear the word using the C key and
enter the word you want using Alphabet mode.
4. Press the OK soft key.
Entering Text
53
The word is added to the T9 dictionary and becomes
the first word for the associated keypress.
♦To enter periods, hyphens or apostrophes, press the
1 key. T9 mode applies grammar rules to ensure
that the correct punctuation is used.
♦To shift the case in T9 mode, use the key. There
are three cases; Initial Capital ( ), Capital lock (
and Lower case ( ).
)
♦You can move the cursor by using the Left and
Right keys. To delete letters, press the C key. Press
and hold the C key to clear the display.
Entering Text
54
Using Alphabet Mode
Use the 1 to 0 keys to enter your text.
1. Press the keys labeled with the letter you want:
- Once for the first letter
- Twice for the second letter
- And so on
2. Select the other letters in the same way.
Note: The cursor moves to the right when you press a different key. When
entering the same letter twice or a different letter on the same key, just wait for
a few seconds for the cursor to move to the right automatically, and then select
the next letter.
Refer to the table below for further details about the
characters available:
Characters in the Order Displayed
Key
Lower Case
Upper Case
€
€
♦To insert a space, press the
key.
Entering Text
55
♦To shift the case in Alphabet mode, use the key.
There are three cases; Capital lock ( ), Lower
case ( ) and Initial Capital ( ).
♦You can move the cursor by using the Left and
Right keys. To delete letters, press the C key. Press
and hold the C key to clear the display.
Using Number Mode
Number mode enables you to enter numbers into a
text message. Press the keys corresponding to the
digits you want to enter.
Using Symbol Mode
Symbol mode enables you to insert symbols into a
text message.
To
Press the
select a symbol
corresponding number key.
display more
symbols
Up or Down key.
clear the symbol(s)
C key. When the input field is
empty, this key returns the
screen to the previous mode.
insert the symbol(s)
into your message
OK soft key.
cancel your input and Back soft key.
return to the previous
mode
Entering Text
56
Options During a Call
Your phone provides a number of control functions
that you can use during a call.
Putting a call on Hold
You can place the current call on hold whenever you
want. You can make another call while you have a
call in progress if your network supports this service.
To place a call on hold, simply press the Hold soft key.
You can reactivate the call whenever you want, by
pressing the Unhold soft key.
To make a call while you have a call in progress:
1. Put the current call on hold by pressing the Hold
soft key.
2. Enter the phone number that you wish to dial or
look it up in Phone Book.
For details about searching for a number in Phone Book,
3. Press the
key to dial the second call.
When you have an active call and a call on hold,
you may switch between the two calls, changing the
one on hold to active and placing the other on hold.
To switch between the two calls, simply press the
Swap soft key.
The current call is placed on hold and the call on
hold is reactivated so that you can continue
conversing with the other person.
Options During a Call
57
When you want to finish, end each call by pressing
the key.
Using the Menu Functions
During a call, you can access the main menu
functions.
1. Press the Options soft key.
2. Press the OK soft key when the Menu option
highlights.
3. Press the Up or Down key to scroll through the
menu list.
Note: You cannot use some menus during a call. They
are deactivated on this list.
4. When the menu you want highlights, press the
Select soft key.
5. If the selected menu has sub-options, repeat steps
3 and 4.
For further details about the menu functions
Switching the Microphone Off (Mute)
You can temporarily switch your phone’s
microphone off so that the other person on the
phone cannot hear you.
Example: You wish to say something to another person
in the room but do not want the person on the
phone to hear you.
Options During a Call
58
To switch the microphone off temporarily:
1. Press the Options soft key.
2. Press the Down key to highlight the Mute option.
3. Press the OK soft key.
The other person can no longer hear you.
To switch the microphone back on:
1. Press the Options soft key.
2. If necessary, press the Down key to highlight the
Unmute option.
3. Press the OK soft key.
The other person can hear you again.
Muting or Sending Key Tones
These options allow you to turn the key tones off or
on. If the Mute Keys option is selected, your phone
does not transmit the DTMF (Dual Tone Multi-
Frequency) tones of the keys, which allows you to
press keys without hearing annoying key tones during
a call.
Note: To communicate with answering machines or
computerized telephone systems, the Send Keys option
must be selected.
Options During a Call
59
Sending a Sequence of DTMF Tones
You can send the DTMF tones after entering the
entire number you need to send.
This option is helpful for entering a password or an
account number when you call an automated
system, like a banking service.
To send the DTMF tones:
1. When you are connected to the teleservice
system, press the Options soft key.
2. Press the Down key to highlight the Send DTMF
option.
3. Press the OK soft key.
4. Enter the number you want to send and press the
OK soft key. The tones are sent.
Searching for a Number in Phone Book
You can search for a number in Phone Book during a
call.
1. Press the Options soft key.
2. Press the Down key to highlight the Phonebook
option.
3. Press the OK soft key.
The Phone Book entries are listed.
4. Enter the name that you wish to find.
Options During a Call
60
If you enter the first few letters of the name, the Phone
Book entries are listed, starting with the first entry
matching your input.
5. To view the highlighted entry, press the View soft
key.
For further details about the Phone Book feature, see
Using the SMS Service
If you receive an SMS (Short Message Service)
message during a call, the Message icon ( ) flashes
on the display. The SMS Service option enables you to
read the message. You can also write a new text
message.
For further details about the SMS service, refer to
Call Waiting
You can answer an incoming call while you have a
call in progress, if your network supports this service
and you have set the Call Waiting menu (Menu 8.2) to
incoming call by a call waiting tone.
To answer a call while you have a call in progress:
1. Press the
key to answer the incoming call. The
first call is automatically put on hold.
2. To switch between the two calls, press the Swap
soft key.
Options During a Call
61
3. To end the call on hold, press the Options soft key
and select the End Held Call option.
To end the current call, press the
key.
Making a Multi-party Call
A multi-party call is a network service that allows up
to six people to take part simultaneously in a multi-
party or conference call. For information, contact
your service provider.
Setting up the Multi-party Call
1. Call the first participant in the normal way.
2. Call the second participant in the normal way. The
first call is automatically put on hold.
3. To join the first participant to the multi-party call,
press the Options soft key and select the Join
option. Press the OK soft key.
4. To add a new person to the multi-party call, call
the person in the normal way and press the
Options soft key. Select the Join option and press
the OK soft key.
You can add incoming callers by answering the call,
pressing the Options soft key, and selecting the Join
option. Repeat as required.
Having a Private Conversation with One Participant
1. Press the Options soft key and choose the Select
One option. Press the OK soft key.
Options During a Call
62
The list of call participants appears.
2. Highlight a person from the list by pressing the Up
or Down key, and press the Select soft key or the
key.
3. When the Private option highlights, press the OK
soft key.
You can now talk privately to that person. The other
participants can still converse with each other.
4. To return to the multi-party call, press the Options
soft key and select the Join option. Press the OK
soft key.
All the multi-party call participants can now hear each
other.
Dropping One Participant
1. Press the Options soft key and choose the Select
One option. Press the OK soft key.
The list of call participants appears.
2. Highlight a person from the list by pressing the Up
or Down key, and press the Select soft key or the
key.
3. Press the Down key to select the Remove option
and press the OK soft key.
The call ends with that participant, but you can
continue to talk to the others.
Options During a Call
63
Using the Menus
The phone offers a range of functions that allow you
to tailor it to your needs. These functions are
arranged in menus and sub-menus.
The menus and sub-menus can be accessed by
scrolling using the Navigation keys or by using the
shortcuts.
Accessing a Menu Function by Scrolling
1. In Idle mode, press the Menu soft key to access
Menu mode.
2. Scroll using the Up or Down key to reach a main
menu, Phone Settings for example. Press the Select
soft key or the Right key to enter the menu.
3. If the menu contains sub-menus, Language for
example, you can access them by scrolling using
the Up or Down key and pressing the Select soft
key or the Right key.
If the menu that you have selected contains further
options, repeat this step.
To
Press the
scroll through the
menus
Up or Down key, or use the
Volume keys.
confirm the chosen
setting
Select soft key or the Right
key.
Using the Menus
65
To
Press the
return to the previous
menu level
Left key, C key or
soft key.
exit the menu without
changing the settings
key.
Using Shortcuts
The menu items, such as menu, sub-menus and
options, are numbered and can be accessed quickly
by using their shortcut numbers. The shortcut number
is shown at the bottom right next to the
soft key on
the display. Simply press the Menu soft key and enter
the number of the menu you want.
Note: The numbers assigned to each menu are
the menu number on the phone, depending on the
services supported by your SIM card.
Example: Accessing the Language menu.
1. Press the Menu soft key.
2. Press the 6 key for Phone Settings.
3. Press the 4 key for Language.
The languages available display.
List of Menu Functions
The following list shows the menu structure available
and indicates the number assigned to each option
and the page where you can find a description of
each feature.
Using the Menus
66
Note: If you use a SIM AT card that provides additional
services, the SIM AT menu displays when you press the
Menu soft key to enter Menu mode. For further details,
see your SIM card instructions.
1. Text Messages (see page 73)
1.1 Inbox
1.2 Outbox
1.3 Write New
1.4 Templates
1.5 Settings
1.5.1 AWS SMS
*
1.5.2 Setting 2
*
1.5.3 Setting 3
*
1.5.4 Setting 4
1.5.5 Common Setting
1.6 Delete All
1.7 Memory Status
1.7.1 SIM Memory
1.7.2 PHONE Memory
*
1.7.3 CB Memory
1.8 Voice Mail
1.8.1 Connect to Voice Mail
1.8.2 Voice Mail Number
*
1.9 Broadcast
1.9.1 Read
1.9.2 Receive
1.9.3 Channel List
1.9.4 Language
2. Multimedia Messages (see page 85)
2.1 Inbox
2.2 Outbox
2.3 Draft
2.4 Write New
*.
Shows only if supported by your SIM card.
Using the Menus
67
2.5 Templates
2.6 Delete All
2.7 Memory Status
2.8 Setup
2.9 MMS Profile
3. Call Records (see page 99)
3.1 Missed Calls
3.2 Incoming Calls
3.3 Outgoing Calls
3.4 Delete All
3.5 Call Time
3.5.1 Last Call
3.5.2 Total Outgoing
3.5.3 Total Incoming
3.5.4 Life Time
3.5.5 Reset Timers
*
3.6 Call Cost
3.6.1 Last Call Cost
3.6.2 Total Cost
3.6.3 Max Cost
3.6.4 Reset Counters
3.6.5 Set Max Cost
3.6.6 Price/Unit
4. Camera (see page 103)
4.1 Take Photos
4.2 My Photos
4.3 Record Videos
4.4 My Videos
4.5 Delete All
4.6 Memory Status
5. Sound Settings (see page 113)
5.1 Ring Tone
*.
Shows only if supported by your SIM card.
Using the Menus
68
5.2 Ring Volume
5.3 Alert Type
5.4 Keypad Tone
5.5 Message Tone
5.5.1 SMS Tone
5.5.2 SMS-CB Tone
5.5.3 MMS Tone
*
5.6 Folder Tone
5.7 Power On/Off
5.8 Alerts on Call
5.9 Extra Tones
6. Phone Settings (see page 117)
6.1 Display Settings
6.1.1 Wallpaper
6.1.2 Front LCD
6.1.3 Menu Style
6.1.4 Back Light
6.1.5 Service Light
6.1.6 Graphic Logo
6.2 Greeting Message
6.3 Own Number
6.4 Language
6.5 Security
6.5.1 PIN Check
6.5.2 Change PIN
6.5.3 Phone Lock
6.5.4 Change Password
6.5.5 Privacy
**
6.5.6 FDN Mode
**
6.5.7 Change PIN2
6.6 Extra Settings
6.7 Short Cut
6.8 TTY Setting
6.9 Reset Settings
*.
Shows only if supported by your SIM card.
**. Shows only if supported by your SIM card.
Using the Menus
69
7. Organizer (see page 127)
7.1 Alarm
7.1.1 Once Alarm
7.1.2 Daily Alarm
7.1.3 Morning Call
7.1.4 Remove Alarm
7.1.5 Autopower
7.2 Calendar
7.3 Time & Date
7.3.1 Set Time
7.3.2 Set Date
7.3.3 World Time
7.3.4 Time Format
7.3.5 Auto Update
7.4 Calculator
7.5 To Do List
7.6 Voice Memo
7.6.1 Record
7.6.2 Voice Memo List
7.6.3 Delete All
7.6.4 Memory Status
7.7 Currency Exchange
8. Network Services (see page 139)
8.1 Call Forwarding
8.1.1 Forward Always
8.1.2 Busy
8.1.3 No Reply
8.1.4 Unreachable
8.1.5 Cancel All
8.2 Call Waiting
8.3 Network Selection
8.4 Caller ID
9. Funbox (see page 143)
9.1 WAP Browser
9.1.1 mMode
Using the Menus
70
9.1.2 Bookmarks
9.1.3 http://
9.1.4 Settings
9.1.5 Clear Cache
9.1.6 Push Message
9.2 Games
9.3 Sounds
9.4 Images
9.5 Delete All
9.6 Memory Status
9.6.1 Games
9.6.2 Sounds & Images
Using the Menus
71
Using the Menus
72
Text Messages
Short Message Service (SMS) allows you to send and
receive short text messages to and from other GSM
mobile phones. In addition, your phone supports the
Enhanced Messaging Service (EMS), which enables
you to include simple pictures, melodies and
animated images in your messages. To use this
feature, you must subscribe to your service provider’s
message service.
When the Text Message icon (
) appears, you
have received new text messages. If the memory is
full, an error message displays and you cannot
receive any new messages. Use the Delete option in
each message box to delete the old ones.
Inbox
This message box is used to store the messages that
you have received.
When you enter this menu, the list of messages in the
box displays with the senders’ phone numbers or
names, if available in your Phone Book.
1. Select a message from the list by pressing the Up
or Down key and press the View soft key to read
the message contents.
2. To scroll through the contents, press the Up or
Down key.
3. To scroll to the previous or next message, press the
or
key.
Text Messages
73
While reading a message, you can choose the following
options by pressing the Options soft key:
Delete: allows you to delete the message.
Send: allows you to forward the message. For further
Reply: allows you to reply to the sender by sending a text
message.
Call Back: allows you to call the sender back.
Cut Address: allows you to extract the sender’s number
and URL, e-mail addresses or phone numbers from the
message text.
Move to Phone: allows you to move the message from the
SIM card to the phone’s memory. This option is only
available when you select a message stored in the SIM
card.
Move to SIM: allows you to move the message from
the phone’s memory card to the SIM card. This
option is only available when you select a message
stored in the Phonebook.
Select Objects: allows you to save media objects, such as
sounds or images, from the message into your phone. You
can use the objects when writing a message. For details,
Outbox
This message box is used to store the messages that
you have already sent or will send.
When you enter this menu, the list of messages in the
box displays with the recipients’ phone numbers or
names, if available in your Phone Book.
Text Messages
74
1. Select a message from the list by pressing the Up
or Down key and press the View soft key to read
the message contents.
2. To scroll through the contents, press the Up or
Down key.
3. To scroll to the previous or next message, press the
or
key.
While reading a message, you can choose the
following options by pressing the Options soft key:
Delete: allows you to delete the message.
Send: allows you to send/resend the message. For
further details about how to send a message, see
Cut Address: allows you to extract the destination
number and URL, e-mail addresses or phone numbers
from the message text.
Move to Phone: allows you to move the message from
the SIM card to the phone’s memory. This option is
only available when you select a message stored in
the SIM card.
Move to SIM: allows you to move the message from the
phone’s memory card to the SIM card. This option is only
available when you select a message stored in the
Phonebook.
Select Objects: allows you to save media objects,
such as sounds or images, from the message into
your phone. You can use the objects when writing a
Text Messages
75
Write New
In this menu, you can write and send a text message.
Note: When you add media objects to the message, the
number of characters you can enter decreases.
Creating a Simple Text Message
1. Create your message.
For further details about entering characters, see page 51.
2. When you finish entering the message, press the
Options soft key. The following options are
available:
♦Send Only: allows you to send the message. The
message is deleted after sending.
♦Save and Send: allows you to save a copy of the
message and then send the message. You can
read the message in your Outbox.
♦Save Only: allows you to save the message so that
it can be sent later. You can read the message in
your Outbox.
For further details about Text Formatting, Add
Objects, Add Templates, Add Phonebook, Add
3. Select Send Only or Save and Send, and press the
Select soft key.
If you want to just save the message, select Save Only.
After saving the message, the phone returns to the Text
Messages menu screen.
Text Messages
76
4. If you select a save option, choose the memory
location and press the OK soft key.
5. Enter a destination number and press the OK soft
key. The message is sent
.
Note: When the phone fails to send the message, it asks
you if you want to retry. Press the OK soft key to confirm.
Otherwise, press the Exit soft key to return to the Write
New screen.
Creating a Message Using the Options
1. Create a message.
2. Press the Options soft key.
3. Select one of the following options by using the Up
and Down keys and pressing the Select soft key:
♦Text Formatting: allows you to format the style of
the text.
♦For the Size attribute, Normal, Large and Small sizes
are available. For the Underline and Strikethrough
attributes, select On or Off.
♦These attributes can be combined.
♦Add Objects: allows you to add a sound, melody,
picture or animated image to the message. Select
the category of the object to be added. In each
category, you can select from the various factory-
set items or choose an item received from other
sources, such as the Internet or other phones.
♦Add Templates: allows you to apply one of the
preset message templates to the text. Select one of
nine messages stored in the Templates menu (Menu
Text Messages
77
♦Add Phonebook: allows you to add a Phone Book
entry to your message. Select one from the list.
♦Add Bookmark: allows you to add a web page
address stored in your Bookmarks list (Menu 9.1.2).
Select one from the list.
♦Language: allows you to change the language to
be used in the T9 input mode. Select the language
you want to use.
4. Complete the message, and send or save it by
following the procedure from step 2 on page 76.
Templates
Using this menu, you can preset a maximum of nine
messages that you use most frequently.
Select the message template you want and press the
Options soft key.
The following options are available:
Edit: allows you to write a new message or edit the
message.
Note: For further details about entering characters, see
Send Message: allows you to retrieve the message. Once
you have completed the message, you can send, save and
send, or simply save it. For further details about how to
Delete: allows you to delete the message. You are asked
to confirm the deletion by pressing the Yes soft key.
Settings
In this menu, you can set up default message
information. A setting group is a collection of settings
Text Messages
78
required to send messages. The number of setting
groups available depends on the capacity of your
SIM card.
Note:
1.The setting options available in this menu may be
different depending on your service provider.
2.The last setting you accessed is automatically activated for
sending messages.
AWS SMS (default setting)/Setting x (where x is the setting
group number): each group has its own sub-menu.
Service Center: allows you to store or change the number of
your message center, which is required when sending
messages. You must obtain this number from your service
provider.
Default Destination: allows you to store the default
destination number. The number automatically displays on
the Destination screen when you create a message.
Default Type: allows you to set the default message type to
Text, Fax, Email or Paging. The network can convert the
messages into the selected format.
Default Validity: allows you to set the length of time your text
messages are stored in the message center while
attempts are made to deliver them.
Setting Name: allows you to give a name to the setting group
currently being defined.
Common Setting: The following options are available:
Reply Path: allows the recipient of your message to send
you a reply through your message center, if your network
supports this service.
Text Messages
79
Delivery Reports: allows you to activate or deactivate the
report function. When this function is activated, the
network informs you whether or not your message has
been delivered.
Bearer Selection: allows you to choose either GSM or GPRS,
depending on your network.
Character Support: allows you to choose either GSM-
Alphabet, Uni-Code or Automatic, depending on your
network. If you select Uni-Code and your recipient’s
phone does not support it, your recipient may not be
able to read your message.
Delete All
This menu allows you to delete all of the text
messages in each message box. You can also delete
all of your messages at one time.
To
Press the
select a message
box to clear
Up or Down key. To delete all of your
messages, select All Messages.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
delete the marked
messages
Delete soft key.
When a confirming message displays, press the Yes
soft key to confirm.
Text Messages
80
Memory Status
This menu shows how many messages are currently
stored in the SIM, phone and CB (cell broadcast)
memories.
Voice Mail
This menu allows you to access your voice mailbox, if
your network supports this service.
The following options are available:
Connect to Voice Mail: before using the Voice Mail
feature, you must enter the voice server number
obtained from your service provider; see menu
option 1.8.2. You can then select this option and press
the OK soft key to listen to your messages.
You can quickly connect to the voice server by
pressing and holding the 1 key in Idle mode.
Voice Mail Number: allows you to change the voice
mail server number, if necessary.
To
Press the
enter the server number corresponding numeric keys.
correct a digit C key.
move the cursor to the Left or Right key.
left or right without
clearing a digit
Note: Voice Mail is a network feature. Please contact
your service provider for further details.
Text Messages
81
Broadcast
This network service allows you to receive text
messages on various topics, such as the weather or
traffic. Cell Broadcast (CB) messages display as soon
as they are received, provided that:
♦the phone is in Idle mode.
♦the Receive option is set to Enable.
♦the message channel is currently active on the
channel list.
This menu may not be available depending on your
SIM card.
The following options are available:
Read: lets you view the received message. The
Volatile box displays the messages from the network,
but loses its contents as soon as the phone is
switched off. Scroll through the message by using the
Up and Down keys. While reading a message, press
the Save soft key to store the message in the Archive
box for later retrieval.
Receive: allows you to enable or disable the
reception of broadcast messages.
Channel List: allows you to indicate the channels
from which you wish to receive broadcast messages.
The following options are available:
Select: use to enable or disable channels on the list by
marking or unmarking them respectively. A check
mark displays in front of each selected channel.
Add Channel: use to enter the ID and title for a new
channel.
Delete: use to remove a channel from the list.
Text Messages
82
Edit: use to change the ID and title of an existing
channel.
Language: allows you to select your preferred
language to display cell broadcast messages.
Please contact your service provider for further
details.
Text Messages
83
Text Messages
84
Multimedia Messages
The menu allows you to use the Multimedia Message
Service.
Multimedia Message Service (MMS) is a messaging
service very similar to Short Message Service (SMS). It
provides automatic and immediate delivery of
personal multimedia messages from phone to phone
or from phone to e-mail.
In addition to the familiar text content of text
messages, multimedia messages can contain
images, graphics, voice and audio clips. An MMS
message is a multimedia presentation in a single
entry. It is not a text file with attachments.
Using the MMS feature, your phone can receive and
send messages that contain multimedia files, such as
your photos, videos and voice memos you recorded.
This function is available only if it is supported by your
service provider. Only phones that offer multimedia
message features can receive and display
multimedia messages.
Inbox
Viewing a Message When You Receive it
When a new multimedia message comes in, the
display shows the MMS Message icon ( ) and a text
notification along with the sender’s number.
1. Press the Select soft key to view brief information
about the message, such as the sender’s number,
the message size and the subject.
Multimedia Messages
85
If you want to view the message later in the Inbox, press
the Exit soft key.
2. To scroll through the message information, press
the Up or Down key.
3. Press the Options soft key to use the following
options:
♦Retrieve: retrieves the message from the MMS
server.
♦Delete: deletes the message.
♦Properties: shows you detailed information about
the message.
4. To read the message, press the Select soft key
when Retrieve is highlighted.
Your phone retrieves the message contents from the
server and display it.
5. To scroll through the message, press the Up or
Down key.
6. When you are finished, press the
key.
Viewing a Received Message in the Inbox
When you access the Inbox menu (Menu 2.1), the list
of multimedia, video or voice note messages you
received displays with the senders’ phone numbers, if
they are available in your Phone Book, or subjects.
The icons on the left tell you the status of the
messages.
♦
: Messages that have been opened.
Multimedia Messages
86
♦
: Messages that are unopened.
1. Select a message on the list and press the Select
soft key.
The message displays and scrolls to the next page, if it
has one, after a specified time; for details about setting
2. Press the OK soft key to go to the message view
screen.
Or, the display will automatically switch to the screen.
3. To scroll through the message, press the Up or
Down key.
If the message has more than one page, you can scroll
through the pages by using the Left and Right keys.
While viewing a message, you can choose the
Message options by pressing the Options soft key.
If you are viewing a new message, the options are
the same as when you view a message as soon as
When you are reviewing a message retrieved from
the MMS server, the following options are available:
Delete: deletes the message.
Reply: allows you to reply to the sender by sending a
text, multimedia or voice note message, depending
on the type of the received message.
Callback: allows you to call the sender back.
Cut Address: allows you to extract the sender’s
number or e-mail address and URL, e-mail addresses
or phone numbers from the message text.
Multimedia Messages
87
Send: allows you to forward the message to another
person.
Save Picture: allows you to save a picture from the
message into your phone. They are stored in the
Images folder (Menu 9.4).
Save Sound: allows you to save a sound from the
message into your phone. They are stored in the
Sounds folder (Menu 9.3).
Properties: shows you information about the
message, such as the subject, sender’s e-mail
address or phone number, message size, transaction
ID, message class, MMS version, recipient’s e-mail
address or phone number, priority and the time and
date when the message was received.
Outbox
When you access this menu, the list of the picture,
video or voice note messages you sent or saved
displays. The icons on the left tell you the status of the
messages.
♦
♦
♦
♦
♦
: Messages currently being sent
: Messages sent
: Messages your phone couldn’t send
: Messages to be sent
: Messages deferred
1. Select a message on the list and press the Select
soft key.
The message displays and scrolls to the next page, if it
has one, after a specified time; for details about setting
Multimedia Messages
88
2. Press the OK soft key to go to the message view
screen.
Or, the display will automatically switch to the screen.
3. To scroll through the message, press the Up or
Down key.
If the message has more than one page, you can scroll
through the pages by using the Left and Right keys.
While viewing a message, you can choose the
following options by pressing the Options soft key:
Delete: deletes the message.
Cut Address: allows you to extract the destination
numbers or e-mail addresses and URL, e-mail
addresses or phone numbers from the message text.
Send: allows you to resend the message.
Edit Message: allows you to change the message
contents, sound, photo or text.
Properties: shows you information about the
message, such as the status, subject, sender’s e-mail
address or phone number, message size, transaction
ID, MMS version and the time and date when the
message was sent.
Draft
After creating a multimedia message, you can store
it in this message box for later sending.
For further details about viewing a message, see
Multimedia Messages
89
Write New
This menu allows you to create a new multimedia
message and then send it to multiple destinations.
Creating and Sending a Multimedia Message
1. Enter the subject of your message and press the
OK soft key.
For further details about entering characters, see
2. When Add Here highlights, press the Options soft
key and add the message contents using one of
the following options:
♦Add Text: enter the message text and press the OK
soft key.
♦Add My Photo: allows you to add a photo you took
using the camera on your phone. Select New Photo
to take a new photo, or My Photos to add one of
the photos stored in the phone. For further details
about using the camera, see page 103.
♦Add Picture: allows you to add a photo stored in the
Images folder (Menu 9.4). Choose a photo and
press the Select soft key. You may not be able to
add some downloaded images if they are not in
the correct format.
♦Add Sound: allows you to add a sound file. Select
Record to record a new voice memo, or Sound List
to add one of the sounds in the Sounds folder (Menu
9.3) or Voice Memo List (Menu 7.6.2). You may not
be able to add some downloaded sounds if they
are not in the correct format.
♦Send: allows you to send the message. Use this
option when you finish creating the message.
Multimedia Messages
90
♦Save: saves the message in the Draft (Menu 2.3) or
Templates (Menu 2.5) box for later use. This option is
activated after you add content to the message.
♦Settings: allows you to change the message
settings. For further details about each setting
you need to press the
soft key or the C key to go
to back to the options screen.
♦Add Destination: allows you to enter destination
numbers or addresses. See steps 6 to 11 starting
press the
soft key or the C key to go to back to
the options screen.
♦Preview: shows your message as it will display on the
recipient’s phone.
You can add text, an image and a sound once for each
page.
3. Repeat step 2 until you finish creating your
message.
4. If you want to change the added items, press the
Up or Down key to highlight one and press the
Options soft key. The following options are
available:
The options available are different depending on whether
the item you select on the message screen is text, an
image, a sound, a video or the Page field.
♦Edit Text/Picture/Sound: allows you to change the
text or replace the photo, voice memo, video with
another one.
♦Add Page: allows you to add more pages. After you
add a page, the display shows you the current
page number and memory space used for the
Multimedia Messages
91
page. You can move to each page using the Left
or Right key on the message screen.
♦Delete: deletes the item from your message.
♦Duration: allows you to set when an image or a
sound displays on the message presentation screen
and a length of time it will display for. When the
message is opened, the display shows the item
after a specified time in Set Start Time and scrolls to
the next item after a specified time in Set Duration.
♦Send: allows you to send the message.
♦Save: saves the message in the Draft (Menu 2.3) or
Templates (Menu 2.5) box for later use.
♦Settings: allows you to change the message
settings. For further details about each setting
option, see page 93.
♦Add Destination: allows you to enter destination
addresses. See steps 6 to 11.
♦Preview: shows your message as it will display on the
recipient’s phone.
5. When you have finished creating the message,
choose Send from the options and press the Select
soft key.
6. Select a destination type, To, Cc or Bcc and press
the Select soft key.
7. Choose one of the following options and press the
Select soft key:
♦Phone Number: allows you to enter the phone
number you want.
♦E-Mail Address: allows you to enter the e-mail
address of the recipient.
♦Phone Book: allows you to retrieve a number from
your Phone Book.
Multimedia Messages
92
8. Enter a number or an e-mail address, or select a
number from your Phone Book.
9. When the correct number or address displays,
press the OK soft key.
10.To add a destination, press the Select soft key
when Add Destination highlights. Repeat from step
7.
If you want to edit the destinations, select one and press
the Select soft key. You can change or delete it.
11.To enter additional numbers or addresses to the
other destination types, press the C key or the
soft key and repeat steps 6 through 10.
You can enter up to 10 destinations each for To, Cc and
Bcc
.
12.When you are finished entering the destinations,
select Send Message and press the Select soft key.
Your phone sends the message.
Using the Message Setting Options
When you select Settings from the message options,
the following options are available:
Delivery Report: when this option is enabled, the
network informs you whether or not your message
has been delivered.
Read Reply: when this option is enabled, your phone
sends a request for a reply along with your message
to the recipient.
Multimedia Messages
93
Hide ID: when this option is enabled, your phone
number does not display on the recipient’s phone.
Expiry Date: you can select the length of time your
messages are stored in the message center after
they are sent.
Delivery Time: you can set a delay time before the
phone sends your messages.
Priority: you can select the priority level of your
messages.
Templates
This menu stores messages you saved as templates so
that you can use them to make new messages.
1. Scroll through the template list using the Up and
Down keys.
2. When the message template you want highlights,
press the Select soft key.
3. Press the OK soft key to use the following options,
or the display will automatically show the options
after a specified time:
♦Edit: allows you to send a message using the
template. For further details about how to send a
message, see page 90.
♦Delete: allows you to delete the message. You are
asked to confirm the deletion by pressing the Yes
soft key.
4. Press the
key to return to Idle mode.
Multimedia Messages
94
Delete All
This menu allows you to delete all of the multimedia
messages in each message box. You can also delete
all of your messages at one time.
To
Press the
select a message
box to clear
Up or Down key. To delete all of
your messages, select All
Messages.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
delete the marked
messages
Delete soft key.
When a confirming message displays, press the Yes
soft key to confirm.
Memory Status
You can check the amount of memory being used
and the memory remaining for multimedia
messages.
The display shows the total space, including the free
and used space. It also shows how much space is
currently occupied by each message box when you
press the Next soft key.
Setup
You can change the default settings for sending or
receiving multimedia messages.
The following options are available:
Multimedia Messages
95
Delivery Report: when this option is enabled, the
network informs you whether or not your message
has been delivered.
Read Reply: when this option is enabled, your phone
sends a request for a reply along with your message
to the recipient.
Auto Download: you can set whether or not your
phone retrieves new incoming messages from the
MMS server without notifications. When this option is
enabled, the phone automatically retrieves new
messages from the server. As soon as you receive a
message, you can use more options while you are
options.
Message Acceptance: you can specify the category
of messages you want to receive.
Hide ID: when this option is enabled, your phone
number does not display on the recipient’s phone.
Expiry Date: you can select the length of time your
messages are stored in the message center after
they are sent.
Delivery Time: you can set a delay time before the
phone sends your messages.
Priority: you can select the priority level of your
messages.
Report Allowed: when this option is enabled, the
sender of an incoming message receives a delivery
report from the network.
Page Duration: you can set the length of time one
page of a received message displays on the
Multimedia Messages
96
message presentation screen. After a specified time,
the display automatically scrolls to the next page.
MMS Profile
In this menu, you can configure various network
settings that are required when you send or receive
multimedia messages.
Note:
1.The last profile you accessed is automatically activated
for sending messages.
2.If you change the MMS settings without first checking with your
service provider, the MMS feature may not work properly.
The following options are available for each profile:
Profile Name: enter a name that you wish to assign to
the MMS server.
Connection URL: enter the address of your MMS
server.
Security: select a data transmission mode. Choose
Secure to protect your data against unauthorized
access; otherwise, choose Non-Secure.
IP Address: enter the gateway address required to
connect to the MMS server.
User Name: enter the user ID required to connect to
the MMS server.
Password: enter the password required to connect to
the MMS server.
APN: enter the access point name used for the
address of the MMS server.
For further details, contact your service provider.
Multimedia Messages
97
Multimedia Messages
98
Call Records
In this menu, you can view the:
♦calls you missed, received or dialed.
♦length of your calls.
♦cost of your calls.
Note:
1.You can access the numbers in the three types of call
records by pressing the
key in Idle mode.
2.The number of call records the phone can store may be different
depending on your SIM card.
Missed Calls
This menu lets you view the last 20 numbers of the
calls you received, but did not answer.
The number or name, if available, displays together
with the time and date when the call was received.
By pressing the Options soft key, you can:
♦edit the number, if available, and dial it or save it in
Phone Book.
♦delete the call from the list.
You can also dial the number by pressing the
key.
Incoming Calls
This menu lets you view the last 20 numbers of the
calls you received.
The number or name, if available, displays together
with the time and date when the call was received.
By pressing the Options soft key, you can:
♦edit the number, if available, and dial it or save it in
Phone Book.
Call Records
99
♦delete the call from the list.
You can also dial the number by pressing the
key.
Outgoing Calls
This menu lets you view the last 20 numbers you
dialed.
The number or name, if available, displays together
with the time and date when the call was made.
By pressing the Options soft key, you can:
♦edit the number and dial it or save it in Phone Book.
♦delete the call from the list.
You can also dial the number by pressing the
key.
Delete All
This menu allows you to delete all of the records in
each call record. You can also delete all of your call
records at one time.
To
Press the
select a call record Up or Down key. To delete all of your
to clear call records, select All Calls.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
delete the marked
records
Delete soft key.
When a confirming message displays, press the Yes
soft key to confirm.
Call Records
100
Call Time
This menu lets you view the timers for calls you made
and received.
Note: The actual time invoiced for calls by your service
provider may vary, depending on network features,
rounding-off for billing purposes and so on.
The following timers are available:
Last Call: length of the last call.
Total Outgoing: total length of all calls you made
since the timer was last reset.
Total Incoming: total length of all calls you received
since the timer was last reset.
Life Time: shows the number and total duration of all
calls made to or from your phone since the phone
was shipped from the factory.
Reset Timers: option used to reset the call timers. You
must first enter the phone password and then press
the OK soft key.
Note: The password is preset to “00000000” at the
factory. To change this password, see page 121.
Call Cost
This network feature lets you view the cost of calls.
This menu may not be available depending on your
SIM card.
The following options are available:
Last Call Cost: cost of the last call you made.
Total Cost: total cost of all calls you made since the
cost counter was last reset. If the total cost exceeds
the maximum cost set in the Set Max Cost option, you
Call Records
101
can no longer make any calls until you reset the
counter.
Max Cost: maximum cost set in the Set Max Cost
option. See below.
Reset Counters: option used to reset the cost counter.
then press the OK soft key.
Set Max Cost: option used to enter the maximum
cost that you authorize for your calls. You must first
OK soft key.
Price/Unit: option used to set the cost of one unit; this
price per unit is applied when calculating the cost of
your calls. You must first enter your PIN2 (see
Call Records
102
Camera
Using the camera module in your phone, you can
take photos of people or events while on the move.
Additionally, you can send photos to other people in
a multimedia message or set one as a wallpaper.
You can also record videos using your phone as a
camcorder.
Note: You can quickly enter the Camera menu by
pressing the UP key in Idle mode.
CAUTION:
Do not take photos of people without their permission.
Do not take photos in a place where cameras are not allowed.
Do not take photos in a place where you may interfere with another
person’s privacy.
Take Photos
This menu allows you to take a photo. Your camera
produces JPEG photos.
Notes:
1.When you take a photo in direct sunlight or in bright
conditions, shadows may appear on the photo.
2.When you take a photo in bright lighting conditions indoors,
white lines may appear on the display. To clear this problem,
press the
to exit this mode. Press the
6
key. If you want to take a photo outdoors, you need
key again.
6
Camera
103
Taking a Photo with the Folder Open
1. Access the Take Photos menu to turn the camera
on. Or you can press and hold the Camera key (
)
on the right side of the phone in Idle mode.
The image to be captured appears on the display.
2. Adjust the image by aiming the camera at the
subject.
3.
To
Press the
Left and Right keys.
adjust the brightness
of the image
zoom in or out
Up and Down keys.
Volume keys.
flip vertically or
horizontally
use the camera
options
right soft key.
1 key.
change the camera
mode
change the display
size
2 key.
change the image
quality
3 key.
change the shot
mode
4 key.
apply effects
5 key.
Camera
104
To
Press the
use a frame
set a delay time
7 key.
8 key.
Press the left soft key to
take the picture using
the delay function.
move to the My
Photos or My Videos
menu
9 key.
4. Press the Camera key on the right side of the
phone or the left soft key to take the photo.
5. Press the Save soft key.
To discard the photo and return to the capture mode,
press the Cancel soft key.
To
Press the
use the photo options Options soft key. For
further details, see
return to Capture mode
NewPhoto soft key or C
key.
return to Idle mode
key.
When you press the Options soft key after saving a
photo, the following options are available:
Send: allows you to send the photo using a
Camera
105
Set as Wallpaper: allows you to set the image as your
wallpaper for the idle screen.
Set as Caller ID: allows you to set the photo as a
caller ID image for Phone Book entries.
Protection: allows you to protect the photo from
being deleted.
Delete: deletes the photo.
Rename: allows you to change the name of the
photo.
Properties: shows the properties of the photo, such as
the time and date it was saved, file size, photo size,
protection status, file format and file name.
Using the Camera Options
In Capture mode, you can use various options by
pressing the right soft key.
To
Press the
scroll to an option
Up or Down key.
select the highlighted
option
Select soft key or the
Right key.
return to Capture mode
C key or
soft key.
The following options are available:
Effects: allows you to change the color tone or apply
special effects to the photo.
Frames: allows you to use a decorated frame. Select
a frame from the list using the Navigation keys.
Multi-Shot: allows you to take a series of action stills.
Select the capture speed, High Speed or Normal
Camera
106
Speed, and the number of photos the camera will
take. When you press the Camera key, the camera
takes photos successively.
After taking photos, press the SaveAll soft key to save
all of them or the Save soft key to save the selected
one.
Rotation: rotates the photo. You can reverse the
photo as a mirror image or flip the photo vertically.
Self Timer: allows you to have a delay time before the
camera takes the photo. Select the length of time
you want. When you press the Camera key, the
camera takes the photo after a specified time.
Settings: allows you to change the options for taking
a photo.
Photo Size: allows you to select a photo size. Once you
change this setting, it is saved for the next shots.
Photo Quality: allows you to change the image quality.
Once you change this setting, it is saved for the next
shots.
Taking a Photo with the Folder Closed
1. Close the folder.
2. To turn the camera on, press and hold the
Camera key on the right side of the phone.
The image to be captured appears on the external
display.
3. Adjust the image by aiming the camera at the
subject.
4. Press the Camera key to take the photo.
Camera
107
The photo is automatically saved in the My Photos menu
Menu 4.2).
(
My Photos
This menu allows you to review your photos.
When you access this menu, your phone displays
them in Thumbnail mode, which shows all your
photos as smaller images. Use the Navigation keys to
scroll through the photos.
To view photos on the full screen, select the photo
you want to view and then press the View soft key. In
this mode, you can scroll through the photos by using
the Left and Right keys. To go back to Thumbnail
mode, press the Multi soft key.
Press the Options soft key to use the following options:
Send: allows you to send the photo using a
Set as Wallpaper: allows you to set the photo as your
wallpaper on the idle screen.
Set as Caller ID: allows you to set the photo as a
caller ID image for Phone Book entries.
Protection: allows you to protect the photo from
being deleted.
Delete: allows you to delete the photo.
Rename: allows you to change the name of the
photo.
Properties: shows the properties of the photo, such as
the time and date it was saved, file size, photo size,
protection status, file format and file name.
Camera
108
Record Videos
You can record a video that is currently displayed on
the camera screen and save it as a video file.
Recording a Video
1. When the camera turns on, adjust the image by
aiming the camera at the subject.
2.
To
Press the
change the camera
mode
1 key.
adjust the brightness
of the image
Left and Right keys.
zoom in or out
Up and Down keys.
3. Press the left soft key or the Camera key to start
recording.
4. When you are finished, press the left soft key or
Camera key. The phone automatically stops when
the recording time expires. The length of the video
may vary depending on the lighting, background,
and recording resolution.
5. Press the Save soft key. The video is saved and the
display returns to Record mode.
Camera
109
My Videos
When you access this menu, the thumbnail images of
the videos display.
To play a video:
1. Press the Navigation keys to scroll to the video you
want to view.
2. Press the Play soft key to start playing the video.
To
pause the playback
resume
Press the
Pause soft key.
Continue soft key.
Stop soft key or C key.
stop
return to Idle mode
key.
Press the Options soft key to use the following options:
Rename: allows you to change the file name.
Delete: deletes the current video file.
Protection: allows you to protect the video from
being deleted.
Properties: show the properties of the video file, such
as the time and date it was saved, file size, protection
status and playing time.
Camera
110
Delete All
This menu allows you to delete each type of the
photos or videos saved in your phone. You can also
delete all of your photos and videos at one time.
To
Press the
select a photo or
video type to clear
Up or Down key. To delete all of your
photos and videos, select All.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
delete the marked
photos or (and)
videos
Delete soft key.
When a confirming message displays, press the Yes
soft key to confirm.
Memory Status
You can check the amount of the memory being
used and the memory remaining in the camera.
The display shows the total, free and used space for
photos. It also shows the space information for videos
when you press the Next soft key.
Camera
111
Camera
112
Sound Settings
You can use the Sound Settings feature to customize
various settings, such as the:
♦ring melody, volume and type.
♦sounds made when you press a key, receive a
message, open/close the folder or switch your
phone on or off.
♦alert tone made every minute during a call, when
you make an error or when your call is connected
to the system.
Ring Tone
This menu allows you to select a ring melody.
You can choose between many different melodies. If
you have downloaded sounds from the Internet or
EasyGPRS program, you can use them in this menu.
Ring Volume
This menu allows you to adjust the ring volume to one
of five levels.
Use the Up and Down keys or the Volume keys on the
left side of the phone to increase or decrease the
volume.
Alert Type
This menu allows you to specify how you are to be
informed of incoming calls or alarms you set.
The following options are available:
Light Only: the service light flashes; the phone neither
rings nor vibrates.
Sound Settings
113
Melody: the phone rings using the selected ring tone
or alarm melody.
Vibration: the phone vibrates but does not ring.
Vibra+Melody: the phone first vibrates three times
and then starts ringing.
Keypad Tone
This menu allows you to select the tone that the
phone sounds when you press a key.
To turn the sound off, select Off.
Message Tone
This menu allows you to select how the phone informs
you that a new message has been received.
SMS Tone
The following options are available for alerting you to
new SMS messages:
Off: the phone does not use an SMS tone.
Light Only: the service light flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
SMS Tone X: the phone uses one of several SMS tones.
SMS-CB Tone
This menu may not be available depending on your
SIM card.
The following options are available for alerting you to
new cell broadcast messages:
Off: the phone does not use a CB tone.
Sound Settings
114
Light Only: the service light flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
SMS-CB Tone X: the phone uses one of several CB
tones.
MMS Tone
The following options are available for alerting you to
new multimedia messages:
Off: the phone does not use a MMS tone.
Light Only: the service light flashes.
Vibration: the phone vibrates.
Single Beep: the phone beeps once.
MMS Tone X: the phone uses one of several MMS
tones.
Folder Tone
This menu allows you to select the tone that the
phone sounds when you open or close the folder.
Select either Future or Crystal.
To turn the sound off, select Off.
Power On/Off
This menu allows you to select the melody that the
phone sounds when it is switched on and off. Select
either Classical or Cheerful.
To turn the sound off, select Off.
Alerts on Call
This menu option allows you to turn off the following
alerts during a call:
Sound Settings
115
● Alarm
● Text messages
● MMS
● SMS
● Low Battery
● WAP Push
The default setting is On. To turn off this setting, select
the Off setting and press the Select soft key.
Extra Tones
You can customize additional tones used for the
phone.
To turn a given tone
Press the
on
off
On soft key. A check mark displays
in front of the option.
Off soft key again. The check
mark no longer displays.
The following options are available:
Error Tone: sets whether or not the phone informs you
when you make a mistake.
Minute Minder: sets whether or not the phone beeps
every minute during an outgoing call to keep you
informed of the length of your call.
Connect Tone: sets whether or not your phone beeps
when your call is connected to the system.
Sound Settings
116
Phone Settings
Many different features of your phone can be
customized to suit your preferences. All of these
features are accessed in the Phone Settings menu.
Display Settings
In this menu, you can change various settings for the
display or backlight.
Wallpaper
This menu allows you to change the background
image or the color of the text to be displayed in Idle
mode.
The following options are available:
Wallpaper: you can select a background image to
be displayed on the idle screen.
To change the background image:
1. Scroll through the list by pressing the Up or Down
key.
You have various preset images available. You can also
select a blank background or any images downloaded
from the Internet and the EasyGPRS program or
received in messages.
2. Press the Select soft key when the image you want
highlights.
3. When the image displays, press the Select soft key
to display it on the idle screen.
Phone Settings
117
Text Display: you can specify whether or not the
phone displays the time and date on the idle screen.
Text Color: you can select the color of the text to be
displayed on the idle screen.
Front LCD
This menu allows you to select the color of an image
to be displayed on the external display.
Menu Style
This menu allows you to select the menu display style.
You can choose either Bar Style or Page Style.
Back Light
You can select the length of time the backlight is on
for. The backlight turns on when you press a key or
receive a call or message and remains on for the
specified length of time.
Service Light
This menu allows you to select whether or not the
service light is used. It also allows you to select a color
in which the service light flashes.
Select one of the seven color settings. When the
phone is ready for use, the service light flashes in the
appropriate color.
If you do not wish to use the service light, select Off.
Phone Settings
118
Graphic Logo
This menu allows you to display your service
provider’s logo instead of its name.
Off: the service provider’s name displays in Idle
mode.
On: the service provider’s logo stored in your phone
displays in Idle mode; if no logo has been stored, the
service provider’s name displays.
Greeting Message
This menu allows you to set a greeting to be
displayed briefly when the phone is switched on.
To
Press the
clear the existing
message
C key and hold it down until the
message is cleared.
enter a new
message
appropriate alphanumeric keys.
right soft key.
change the text
input mode
For further details about entering characters, see
Own Number
This function is a memory aid, which you can use to
check your own phone number if you need to do so.
You can:
♦assign a name to each of your own phone
numbers registered on your SIM card.
♦edit the names and numbers.
Phone Settings
119
Any changes made here do not in any way affect
the actual subscriber numbers on your SIM card.
Language
You can select a display language. When the
language option is set to Automatic, the language is
automatically selected according to the language
of the SIM card used.
Security
The Security feature enables you to restrict the use of
your phone to others and the types of calls.
Various codes and passwords are used to protect the
features of your phone. They are described in the
PIN Check
When the PIN Check feature is enabled, you must
enter your PIN each time you switch the phone on.
Consequently, any person who does not have your
PIN cannot use your phone without your approval.
Note: Before disabling the PIN Check feature, you must
enter your PIN.
The following options are available:
Disable: the phone connects directly to the network
when you switch it on.
Enable: you must enter the PIN each time the phone
is switched on.
Phone Settings
120
Change PIN
This feature allows you to change your current PIN to
a new one, provided that the PIN Check feature is
enabled. You must enter the current PIN before you
can specify a new one.
Once you have entered a new PIN, you are asked to
confirm it by entering it again.
Phone Lock
When the Phone Lock feature is enabled, the phone
is locked and you must enter an 8-digit phone
password each time the phone is switched on.
The password is preset to “00000000” at the factory.
To change the phone password, see the Change
Password menu (Menu 6.5.4) on the following page.
Once the correct password has been entered, you
can use the phone until you switch it off.
The following options are available:
Disable: you are not asked to enter the phone
password when you switch the phone on.
Enable: you are required to enter the phone
password when you switch the phone on.
Change Password
The Change Password feature allows you to change
your current phone password to a new one. You must
enter the current password before you can specify a
new one.
Phone Settings
121
The password is preset to “00000000” at the factory.
Once you have entered a new password, you are
asked to confirm it by entering it again.
Privacy
Using this menu, you can lock your contents, such as
multimedia messages, photos, video clips, voice
memo, downloaded images and sounds. Once you
have locked the contents, you must enter the phone
password to access the associated menus.
To
Press the
select an item to
lock
Up or Down key. To lock all of your
contents, select All.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
lock the marked
items
OK soft key.
When the phone asks for the phone password, enter
the password and press the OK soft key.
Note: The password is preset to “00000000” at the
factory. To change this password, see page 121.
FDN Mode
FDN (Fixed Dial Number) mode, if supported by your
SIM card, allows you to restrict your outgoing calls to
a limited set of phone numbers.
Phone Settings
122
The following options are available:
Disable: you can call any number.
Enable: you can only call phone numbers stored in
Phone Book. You must enter your PIN2.
Note: Not all SIM cards have a PIN2. If your SIM card
does not, this menu does not display.
Change PIN2
The Change PIN2 feature allows you to change your
current PIN2 to a new one. You must enter the current
PIN2 before you can specify a new one.
Once you have entered a new PIN2, you are asked
to confirm it by entering it again.
Note: Not all SIM cards have a PIN2. If your SIM card
does not, this menu does not display.
Extra Settings
You can turn the automatic redialing or answering
features on or off.
To turn a feature
Press the
on
On soft key.
A check mark displays in front of the
option.
off
Off soft key.
The check mark no longer displays.
The following options are available:
Phone Settings
123
Auto Redial: when this option is checked, the phone
makes up to ten attempts to redial a phone number
after an unsuccessful call.
Note: The interval between two attempts varies.
Active Folder: when this option is checked, you can
simply open the folder to answer a call.
When it is unchecked, you must open the folder and
press a key to answer a call, depending on the
setting of the Anykey Answer option. See below.
Anykey Answer: when this option is checked, you
can answer an incoming call by pressing any key,
except the
the call, press the
When this option is unchecked, you can only press
the key or Accept soft key.
key and the Reject soft key. To reject
key or the Reject soft key.
Short Cut
The Navigation keys can be used as shortcut keys. In
Idle mode, they allow you to access specific menus
directly.
The Up key is fixed as a shortcut to the Camera
menu. In this menu, you can change the shortcuts
assigned to the Down, Left and Right keys.
To assign a shortcut to a key:
1. Select the key to be used as a shortcut key by
pressing the Up or Down key and press the Select
soft key.
2. Select the menu to be assigned to the key by
pressing the Up or Down key.
Phone Settings
124
To deactivate a shortcut key, select the None option.
3. Press the Select soft key to save the selection.
TTY Setting
TTY, a TDD or Text Telephone, is a telecommunications
device that allows people who are deaf or hard of
hearing, or who have speech or language
disabilities, to communicate by telephone. In this
menu, you can enable your phone’s TTY feature.
The following options are available:
Enable: allows you to communicate with other TTY
users. You can communicate with other TTY users by
connecting certain
portable TTY terminal models to your phone using an
optional adapter.
Disable: does not allow you to communicate with
other TTY users.
Reset Settings
You can easily reset your phone to its default settings.
To reset your phone:
1. Select the Reset Settings menu.
2. Enter the 8-digit phone password and press the OK
soft key.
Note: : The password is preset to “00000000.” To change
this password, see page 121.
Phone Settings
125
Phone Settings
126
Organizer
The Organizer feature enables you to:
♦set an alarm so that the phone rings at a specific
time, such as to remind you of an appointment.
♦view the calendar and organize your schedule.
♦set the current time and date.
♦use the phone as a calculator for basic
mathematical equations or currency exchange
operations.
♦define a list of things to do.
♦record voice memos.
Alarm
This feature allows you to:
♦set the alarm to ring at a specific time.
♦set the phone to switch on automatically and ring
the alarm even if the phone is switched off.
The following options are available:
Once Alarm: the alarm rings only once and is then
deactivated.
Daily Alarm: the alarm rings every day at the same
time.
Morning Call: the alarm rings to wake you up in the
morning.
To set an alarm:
1. Choose the type of alarm to be set and press the
Select soft key.
2. Enter the time for the alarm to sound.
Organizer
127
Your phone is preset to use 12-hour format. To change the
format, see page 132.
If you want to use the alarm options, press the Options
soft key. The following options are available:
•
•
Remove Alarm: deactivates the current alarm.
Alarm Sound Set: allows you to select the alarm melody.
3. Press the OK soft key.
4. Select AM or PM for 12-hour format and press the
Select soft key.
5. If you select Morning Call in step 1, choose the
repeat option, Monday to Friday or Monday to
Saturday, and press the Select soft key.
To stop the alarm when it rings, open the folder and
press the Exit soft key.
Remove Alarm: deactivates all alarm settings.
Autopower: when this option is set to Enable, the
alarm rings at the specified time, even if the phone is
switched off.
If the menu option is set to Disable and the phone is
switched off at the specified time, the alarm does
not ring.
Calendar
With the Calendar feature, you can:
♦consult the calendar to check your memos.
♦write memos to keep track of your schedule.
♦set an alarm to act as a reminder.
Organizer
128
Consulting the Calendar
When you select the Calendar menu (Menu 7.2), the
calendar displays with today’s date highlighted. The
following options are available when you press the
Options soft key:
Search All: displays all of the memos, starting with the
oldest regardless of the day. To scroll through the
memos, press the Up or Down key.
Delete All: allows you to delete all of the memos. You
are asked to confirm your action.
Go to Date: allows you to go to a specific date.
Exit: exits the Calendar feature and returns to Idle
mode.
Writing a Memo
You can make up to 100 memos. To write or edit a
memo on a specific date:
1. Select a date on the calendar, using the
Navigation keys.
To skip to the previous or next month, press the Volume
keys on the left side of the phone.
2. Press the Select soft key.
An empty memo screen displays allowing you to enter
your memo.
3. Enter your memo and then press the OK soft key.
For further details about entering characters, see
Organizer
129
4. If you want the alarm to ring on the chosen day,
press the Yes soft key.
Otherwise, press the No soft key. The memo is saved.
5. If you press the Yes soft key, set the time for the
alarm and press the OK soft key.
Your phone is preset to use 12-hour format. To change
You can set the melody for the alarm by pressing the
Melody soft key.
6. Select AM or PM for 12-hour format and press the
Select soft key.
The color of the date on the calendar changes to
green to indicate that a memo exists for that date.
Viewing a Memo
When you select a day for which a memo already
exists on the calendar, the latest memo for the day
displays.
If more than one memo is stored, press the Up or
Down key to scroll to the previous or next memo.
Press the New soft key to add a new memo for the
day.
You can use the following options by pressing the
Options soft key:
Edit: allows you to change the memo text.
Alarm: allows you to set an alarm to ring at a
specified time to remind you of the memo. If you set
the alarm earlier, you can change or delete it.
Organizer
130
Delete: allows you to delete the memo.
Copy to: allows you to copy the memo to another
date.
Move to: allows you to change the date of the
memo.
Time & Date
This menu allows you to change the current time and
date displayed. You can also find out what time it is in
another part of the world.
The following options are available:
Set Time: allows you to enter the current time. You
can choose the time format in the Time Format menu
(Menu 7.3.4).
Note: Before setting the time, you must specify your
time zone in the World Time menu (Menu 7.3.3).
Set Date: allows you to enter the day, month and
year.
World Time: allows you to find out what time it is in
another part of the world, using the Left and Right
keys.
The screen shows the:
♦city name.
♦current time and date.
♦time difference between the selected city and
your city if you have set the local time.
♦city selected as your time zone.
To select your time zone:
1. Select the city corresponding to your time zone by
pressing the Left or Right key one or more times.
Organizer
131
The local time and date display.
2. Press the Set soft key.
Time Format: allows you to change the time format
to 24 Hours or 12 Hours.
Auto Update: allows you to receive time information
from your service provider’s network.
Off: you need to manually set the time and date
according to the current time zone using the Set Time
menu (Menu 7.3.1).
On: the phone automatically updates the time and
date according to the current time zone using the
network service.
Confirm First: the phone asks for a confirmation
before the update.
Note: Automatic updates of time and date does not
change the time you have set for alarm settings or
calendar memos.
Calculator
With this feature, you can use the phone as a
calculator. The calculator provides basic arithmetic
functions; addition, subtraction, multiplication and
division.
1. Enter the first number using the numeric keys.
Notes:
To delete mistakes or clear the display, press the
C
key.
To include a decimal point or a bracket, press the left soft
key until the symbol you want displays.
Organizer
132
2. Press the right soft key until the arithmetic symbol
you want appears: + (addition), - (subtraction),
* (multiplication), / (division).
3. Enter the second number.
4. To view the result, press the
key.
5. Repeat steps 1 to 4 as many times as required.
To Do List
This feature allows you to:
♦enter a list of tasks to be done.
♦assign a priority and a deadline to each task.
♦sort the tasks by priority and status mark.
Creating the To Do List
1. Press the New soft key.
2. Enter the first task.
For further details about entering characters, see page 51.
3. Press the OK soft key.
4. Select a priority status of high, normal or low using
the Up and Down keys and press the Select soft
key.
5. Enter your deadline and press the OK soft key.
If you do not want to set a deadline, press the Skip soft
key.
Organizer
133
Editing the To Do List
When you select the To Do List menu (Menu 7.5), the
current contents display with the status mark if the
task has been done and priority;
Normal and for Low.
You can use the following options:
for High,
for
Action
Procedures
View the details ➀ Highlight the task.
for a specific
task
➁ Press the View soft key.
➂ Scroll through the tasks using the
Up and Down keys, if necessary.
Change the
status of a
specific task
➀ Highlight the task.
➁ Press the key to mark the task as
completed as of the current time and
date.
or
➀ Highlight the task.
➁ Press the Options soft key.
➂ Select the Mark option.
➃ Select the appropriate status (Done
or Undo).
Create a new
task
➀ Press the Options soft key.
➁ Select the New option.
➂ Enter the text, priority and/or
deadline for the task.
Organizer
134
Action
Procedures (Continued)
Edit an existing ➀ Highlight the task.
task
➁ Press the Options soft key.
➂ Select the Edit option.
➃ Change the text, priority and/or
deadline for the task.
Sort the existing ➀ Press the Options soft key.
tasks by priority
or status
➁ Select the Sort option.
➂ Select the sort criterion (High, Low,
Done or Undo).
Copy a task
➀ Highlight the task.
➁ Press the Options soft key.
➂ Select the Copy option.
➃ Change the text, priority and/or deadline
for the task.
Copy a task to the ➀ Highlight the task.
calendar
➁ Press the Options soft key.
➂ Select the Copy to Calendar option.
➃ Change the text and deadline for the
task and set the alarm.
Delete a task
➀ Highlight the task.
➁ Press the Options soft key.
➂ Select the Delete option.
Delete all tasks ➀ Press the Options soft key.
➁ Select the Delete All option.
➂ Confirm the deletion by pressing
the OK soft key.
Organizer
135
Action
Procedures (Continued)
Exit the To Do
list
➀ Press the Options soft key.
➁ Select the Exit option.
Voice Memo
You can record voice memos. After recording, you
can send a memo to other people using the
Multimedia Message Service.
Record
This menu allows you to record a new memo. When
you select this option, the display shows the 30-
second timer.
1. To start recording, press the Record soft key.
2. Record a memo by speaking into the
microphone.
3. When you press the Stop soft key or if the
recording time expires, the following options
display:
♦Replay: plays back your memo.
♦Re-record: discards the memo and enables you to
record another one.
♦Save: allows you to save the memo.
♦Quit: cancels your recording and exits the Record
menu.
4. To save the memo, choose Save from the options
and press the Select soft key.
Organizer
136
5. Press the C key to clear the default name, if
necessary, and enter a name for the memo.
For further details about entering characters, see
.
6. Press the OK soft key.
The memo is saved and then the display shows the
memo information.
7. Press the Options soft key to use the following
memo options:
♦Send: allows you to send the memo to other people
by using the MMS feature. Follow the procedure on
♦Rename: allows you to change the memo’s name.
♦Delete: deletes the memo.
8. To exit, press the C or
key.
Voice Memo List
This menu shows your voice memo list. Scroll to a
memo and press the Options soft key. The following
options are available:
Play: plays the memo.
Send: allows you to send the memo to other people
by using the MMS feature. Follow the procedure on
Rename: allows you to change the memo’s name.
Information: displays information about the memo,
such as the name, date when the memo was made,
recording duration and memory size.
Organizer
137
Delete: allows you to delete the memo.
Delete All
In this menu, you can delete all of your voice memos.
When a confirming message appears, press the Yes
soft key. To cancel the deletion, press the No soft key.
Memory Status
You can check the amount of memory for voice
memos.
The display shows you the total, free and used space
including the number of memos you recorded and
the total number of memos you can record.
Currency Exchange
Using this menu, you can figure out currency
conversions.
1. Enter the current exchange rate of your source
currency and press the OK soft key.
You can insert a decimal point by pressing the key
.
2. Enter the amount to convert and press the OK soft
key.
The amount you entered and its equivalent value
display.
3. Press the Exit soft key to exit the currency
convertor.
Organizer
138
Network Services
These menu functions are network services. Please
contact your service provider to check their
availability and subscribe to them, if you wish.
Call Forwarding
This network service enables incoming calls to be
rerouted to a number that you specify.
Example: You may wish to forward your business calls
to a colleague while you are on holidays.
You can use the following options to forward voice
calls and/or data calls:
Forward Always: all calls are forwarded.
Busy: calls are forwarded when you are already on
another call.
No Reply: calls are forwarded when you do not
answer the phone.
Unreachable: calls are forwarded when you are not
in an area covered by your service provider.
Cancel All: all call forwarding options are canceled.
To set your call forwarding options:
1. Select a call forwarding option by pressing the Up
or Down key, and then press the Select soft key.
2. Select the type of calls, voice or data, by pressing
the Up or Down key, and then press the Select soft
key.
Network Services
139
The current status displays. If the option has already
been set, the number to which the calls are forwarded
displays.
To
Press the
activate call forwarding Activate soft key. Go to
step 4.
change the number to
be called
Change soft key. Go to
step 4.
deactivate call
forwarding
Remove soft key.
3. Enter the number to which the calls are to be
forwarded and press the OK soft key.
To enter an international code, press the
sign displays.
0
key until the
+
The phone sends your settings to the network and the
network’s acknowledgement displays.
You can deactivate all call forwarding settings by
selecting the Cancel All option.
Call Waiting
This network service informs you when someone is
trying to reach you during another call.
You can specify individual call waiting option for
voice calls and/or data calls:
To set your call waiting options:
Network Services
140
1. Select the type of calls, voice or data, to which
you want to apply the call waiting option by
pressing the Up or Down key, and then press the
Select soft key.
The screen informs you whether call waiting is activated
or deactivated.
2. You can activate or deactivate the call waiting
feature as necessary by using the Activate or
Deactivate soft key respectively.
To return to the previous screen, press the Exit soft
key.
You can also deactivate all call waiting settings by
selecting the Cancel All option.
Network Selection
The Network Selection feature enables you to
automatically or manually select the network used
when roaming outside of your home area.
Note: You can select a network other than your home network only if there is a
valid roaming agreement between them.
To automatically or manually connect to a network
when roaming:
1. When Network Selection displays, press the Select
soft key.
2. Press the Up or Down key until the appropriate
option highlights and then press the OK soft key.
Network Services
141
If you select Automatic, you are connected to the first
available network when roaming.
If you select Manual, the phone scans for the available
networks. Go to step 3.
3. Press the Up or Down key until the network you
want highlights and then press the OK soft key.
You are connected to that network.
Caller ID
You can prevent your phone number from being
displayed on the phone of the person being called.
Note: Some networks do not allow the user to change this setting.
The following options are available:
Default: the default setting provided by the network is
used.
Hide Number: your number does not display on the
other person’s phone.
Send Number: your number is sent each time you
make a call.
Network Services
142
Funbox
The Funbox menu contains several fun options.
WAP Browser
Your phone is equipped with a WAP (Wireless
Application Protocol) browser to allow you to access
and navigate the Wireless Web using your phone.
mMode
Selecting this menu connects the phone to the
network and loads the homepage of the Wireless
Web service provider. You can also press the
in Idle mode.
key
The content of the WAP Browser startup homepage
depends on your Wireless Web service provider. To
scroll through the screen, use the Up and Down keys.
Note: To access the startup homepage from any other screen in the WAP
browser, use the Home option. For further details about the WAP Browser
menus, see page 145.
Exiting the WAP Browser
To exit the browser at any time, simply press the
key.
Funbox
143
Navigating the WAP Browse
r
To
Press the
scroll through and
select browser
items
Up or Down key until the
symbol points to the item,
and then press the Select soft
key to confirm the selection.
select a numbered
item
corresponding numeric key.
return to the
Back soft key or the C key.
previous page
return to the startup
homepage
key for more than two
seconds and select the Home
option. For further details about
this option, see page 145.
Entering Text in the WAP Browser
When you are prompted to enter text, the current text input
mode is indicated on the screen. To change text input
mode, press the
key one or more times.
The following modes are available:
T9 mode (T9): allows you to enter English characters
by pressing one key per letter. In this mode, you can
use only the
0
key to display alternative words. To change
the case, press the key.
Number (1): allows you to enter numbers.
Upper-case character mode (A): allows you to enter
upper-case English characters.
Funbox
144
Lower-case character mode (a): allows you to enter
lower-case English characters.
Note: You can enter special characters in Upper-case or Lower-case Character
mode. For details about available characters, see page 55.
Selecting and Using Browser Menu Options
Various menu options are available when you are
using the WAP Browser to navigate the Wireless Web.
To access a menu option:
1. Press and hold the key.
A menu list displays.
2. Highlight a menu by pressing the Up or Down key.
3. Select an option by pressing the Select soft key.
4. If necessary, select a secondary option using the
Up and Down keys, and press the Select soft key to
confirm.
Note: The menus may vary, depending on your version of the WAP browser.
The following options are available:
Reload: reloads the current page.
Home: takes you back at any time to the home page
of the Wireless Web service provider.
Go to URL: allows you to manually enter the URL
address of a Web page. After entering an address,
press the OK soft key to go there directly.
Funbox
145
Show URL: displays the URL address of the Web page
to which you are currently connected. It also enables
you to set the current site as the startup home page.
To
Press the
set the current page as Option soft key and select
your startup home
the Save to Home option.
page
set a bookmark for the
current page
Option soft key and select
the Save to Bookmark
option
cancel your setting
Back soft key.
Edit Home: allows you to change the startup home
page manually. Enter the URL and press the OK soft
key. For further details about entering text, see
Clear Cache: deletes the information stored in the
cache, which stores the most recently accessed
Web pages.
Inbox: allows you to read messages received from
the web server.
Bookmarks
This menu allows you to store the URL addresses of up
to ten of your favorite web sites. You can access this
menu directly by pressing and holding the key
while using the WAP browser.
To store a URL address:
Funbox
146
1. Select an empty location and press the Options
soft key.
2. Enter the address and press the Enter soft key.
For further details about entering characters, see
3. Enter a name for the favorite item and press the
Enter soft key.
After saving favorite items, you can use the following
options by pressing the Options soft key:
Goto URL: takes you to the site.
Edit: allows you to edit the address and name.
Delete: allows you to delete the item.
http://
This menu allows you to manually enter the URL
address of the Web site that you wish to access.
For further details about entering characters, see
Settings
This menu allows you to set up five proxy servers for
the WAP browser. Contact your service provider for
details about your Settings options.
For each server, the following options are available:
Profile Name: enter a name that you wish to assign to
the HTTP server.
Funbox
147
Homepage URL: set the address of your startup
homepage. When the default homepage displays,
you can delete it using the C key and enter your own
choice.
Security: select a data transmission mode. Choose
Secure to protect your data against unauthorized
access; otherwise, choose Non-Secure.
Bearer: select a bearer to be used for each type of
network address accessed; GPRS or Data.
The remaining options depend on the Bearer setting.
When the bearer is set to GPRS:
IP Address: enter the WAP gateway address required
to connect to the Internet.
User Name: enter the User ID required to connect to
the GPRS network.
Password: enter the password required to connect to
the GPRS network.
APN: enter the access point name used for the
address of the GPRS network gateway.
When the bearer is set to Data:
IP Address: enter the WAP gateway address required
to connect to the Internet.
Login Name: enter the PPP server login ID.
Password: enter the PPP server password.
Dial-up Number: enter the PPP server phone number.
Funbox
148
Data Call Type: select a data call type; Analogue or
ISDN.
Note: The WAP browser settings may vary, depending on the service provider.
Contact your service provider for further details.
Clear Cache
You can clear the information stored in the cache,
the phone’s temporary memory which stores the
most recently accessed Web pages.
Press the Yes soft key to confirm the deletion.
Otherwise, press the No soft key.
Push Message
In this menu, you can receive and access web
messages from the server.
The following options are available:
Inbox: allows you to read the messages received
from the web server.
Receive: allows you to set whether or not your phone
receives web messages.
Delete All: allows you to delete all of the web
messages.
Games
You can download MIDlets (Java applications
running on mobile phones) from various sources using
the WAP Browser and store them in your phone.
When you access the Games menu, the list of the
default games appears.
Funbox
149
Downloading a New Game
You can download more games from the web site
given by your service provider using the mMode
Downloads option. Once you have downloaded
games, they are added to the list.
Note: Java services may not be available depending upon your service
provider.
Launching a MIDlet
Note: The procedures explained below are for the default games. For
downloaded games, the procedure may be different.
1. Scroll to the MIDlet you want on the Games list
and press the Launch soft key.
2. On the startup screen of the MIDlet, scroll to an
option using the Navigation keys.
The following options are available:
•
•
START GAME: starts a new game.
CONTINUE: allows you to continue the last game you
were playing.
•
•
•
HIGH SCORE: shows the high score table. This option
may not be available for some games.
HOW TO PLAY: shows how to play the game and the key
functions for the game.
OPTION: allows you to switch the game sound on or off.
3. Press the
key to confirm your selection.
Funbox
150
While you are playing a
game, to
Press the
adjust the sound
volume
Volume keys
stop the game and
return to the startup
screen
C key.
exit the game
key.
Viewing MIDlet Information
1. Scroll to the MIDlet you want and press the Info
soft key.
The display shows information about the MIDlet, such as
the file size, application version and its vendor.
2. To scroll to other MIDlet information, press the
Navigation keys.
3. If you want to delete the MIDlet, press the Delete
soft key and then press the Yes soft key to confirm
the deletion.
4. To exit and return to the Games screen, press the
Back soft key or the C key.
Note: When you select the default games from the list, the Delete option is
not available, so that you cannot delete them.
Funbox
151
Entering Text
If you need to enter text while using a MIDlet, you
can use the following input modes:
Upper-case character mode (A): allows you to enter
upper-case English characters.
Lower-case character mode (a): allows you to enter
lower-case English characters.
Number mode (1): allows you to enter numbers.
Symbol mode: allows you to enter symbols. After
highlighting a symbol by pressing the Navigation
keys, press the
key to insert it.
T9 mode (T9): allows you to enter English characters
by pressing one key per letter. In this mode, you can
change the case by pressing the 0 key.
To change the text input mode, press the key until
the appropriate indicator appears.
Sounds
In this menu, you can view the list of sounds
downloaded from the web server or received in
multimedia messages. You can set the downloaded
sounds as the current ring tone or send them to other
phones.
By pressing the Options soft key, you can use the
following options:
Rename: allows you to change the name of the
sound.
Delete: deletes the sound.
Set as Ring Tone: sets the sound as your ring tone.
Funbox
152
Images
In this menu, you can view the list of pictures
downloaded from the web server or received in
multimedia messages. You can set the downloaded
pictures as the current background image or send
them to other phones.
If you set a photo as your wallpaper, it displays as My
Photo on the list.
By pressing the Options soft key, you can use the
following options:
Rename: allows you to change the name of the
image.
Delete: deletes the image.
Set as Wallpaper: sets the image as your wallpaper
for the idle screen.
Delete All
This menu allows you to delete all of the downloaded
items in the Games, Sounds or Images folders. You
can delete all of the items at one time.
To
Press the
select a folder to
clear
Up or Down key. To delete all of
your items, select All.
place a check mark Mark soft key.
remove a check
mark
Unmark soft key.
delete the marked
items
Delete soft key.
Funbox
153
When a confirming message displays, press the Yes
soft key to confirm.
Memory Status
You can check the amount of memory being used
and the memory remaining for games, sounds and
images.
Games: the display shows the total, free and used
space and the number of games downloaded.
Sounds & Images: the display shows the total, free
and used space, including the memory status used
by sounds and images.
Funbox
154
Solving Problems
If you are experiencing problems with your phone,
perform the following simple checks before
contacting a service professional. This may save you
the time and expense of an unnecessary service call.
When you switch your phone on, the following messages
may appear:
Insert SIM Card
♦Check that the SIM card is correctly installed.
Phone Locked Enter Password
♦The automatic locking function has been enabled.
You must enter the phone’s password before you
can use the phone.
Enter PIN
♦You are using your phone for the first time. You must
enter the Personal Identification Number (PIN)
supplied with the SIM card.
♦The PIN Check feature is enabled. Every time the
phone is switched on, the PIN has to be entered. To
disable this feature, use the PIN Check menu (Menu
6.5.1).
Enter PUK
♦The PIN code was entered incorrectly three times in
succession and the phone is now blocked. Enter
the PUK supplied by your service provider.
Solving Problems
155
“No service,” “Network failure” or “Not done” displays
♦The network connection was lost. You may be in a
weak signal area (in a tunnel or surrounded by
buildings). Move and try again.
♦You are trying to access an option for which you
have not taken out a subscription with your service
provider. Contact the service provider for further
details.
You have entered a number but it was not dialed
♦Have you pressed the
key?
♦Are you accessing the right cellular network?
Your correspondent cannot reach you
♦Is your phone switched on (the
more than one second)?
key pressed for
♦Are you accessing the right cellular network?
Your correspondent cannot hear you speaking
♦Have you switched off the microphone?
♦Are you holding the phone close enough to your
mouth? The microphone is located at the bottom
of the phone.
The phone starts beeping and “**Warning** Low Battery”
flashes on the display
♦Your battery is insufficiently charged. Recharge the
battery.
Solving Problems
156
The audio quality of the call is poor
♦Check the signal strength indicator on the display
(
); the number of bars indicates the signal
strength from strong (
) to weak ( ).
♦Try moving the phone slightly or moving closer to a
window if you are in a building.
No number is dialed when you recall a Phone Book entry
♦Check that the number has been stored correctly,
by using the Phone Book Search feature.
♦Re-store the number, if necessary.
If the above guidelines do not help you to solve
the problem, take note of:
• the model and serial numbers of your phone
• your warranty details
• a clear description of the problem
Then contact your local dealer or Samsung after-sales
service.
Solving Problems
157
Solving Problems
158
Access Codes
There are several access codes that are used by your
phone and its SIM card. These codes help you
protect the phone against unauthorized use.
When requested for any of the codes explained
below, enter the appropriate code (displayed as
asterisks) and press the OK soft key. If you make a
mistake, press the C key one or more times until the
incorrect digit is cleared and then continue entering
the correct code.
The access codes, except for the PUK and PUK2
codes, can be changed using the Security menu
Important! Avoid using access codes resembling
emergency numbers, such as 911, so that
you do not accidentally dial an emergency
number.
Phone Password
The Phone Lock feature uses the phone password to
protect your phone against unauthorized use. The
phone password is supplied with the phone and is
preset to “00000000” at the factory.
To
See
activate/deactivate the
Phone Lock feature
(Menu 6.5.3).
change the phone
password
Access Codes
159
PIN
The Personal Identification Number or PIN (4 to
8 digits) protects your SIM card against unauthorized
use. It is usually supplied with the SIM card.
If you enter an incorrect PIN three times in succession,
the code is disabled and cannot be used until you
re-enable it by entering the PUK (see below).
To
See
Check feature
change the PIN
PUK
The 8-digit PUK (PIN Unblocking Key) is required to
change a disabled PIN. The PUK may be supplied
with the SIM card. If not, or you have lost it, contact
your service provider.
To re-enable your PIN:
1. Enter the PUK and press the OK soft key.
2. Enter a new PIN of your choice and press the OK
soft key.
3. When the Confirm New PIN message displays,
enter the same code again and press the OK soft
key.
If you enter an incorrect PUK ten times in succession,
the SIM card becomes invalid. Contact your service
provider for a new card.
Access Codes
160
PIN2
The PIN2 (4 to 8 digits), supplied with some SIM cards,
is required to access specific functions, such as
setting the maximum cost of a call. These functions
are available if supported by your SIM card.
If you enter an incorrect PIN2 three times in
succession, the code is disabled and you cannot
access the functions until you re-enable it by entering
the PUK2.
PUK2
The 8-digit PUK2 (PIN Unblocking Key 2), supplied with
some SIM cards, is required to change a disabled
PIN2. If you lose the code, contact your service
provider.
To re-enable your PIN2:
1. Enter the PUK2 and press the OK soft key.
2. Enter a new PIN2 of your choice and press the OK
soft key.
3. When the Confirm PIN2 message displays, enter
the same code again and press the OK soft key.
If you enter an incorrect PUK2 ten times in succession,
you will not be able to access the functions requiring
the PIN2. Contact your service provider for a new
card.
Access Codes
161
Access Codes
162
Health and Safety Information
Exposure to Radio Frequency (RF) Signals
Your wireless phone is a radio transmitter and
receiver. It is designed and manufactured not to
exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal
Communications Commission (FCC) of the U.S.
Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy
for the general population. The guidelines are based
on the safety standards that were developed by
independent scientific organizations through
periodic and through evaluation of scientific studies.
The standards include a substantial safety margin
designed to assure the safety of all persons,
regardless of age and health.
The exposure standard for wireless phones employs a
unit of measurement known as Specific Absorption
Rate (SAR). The SAR limit recommended by the FCC
is 1.6W/kg.*
*. In the U.S. and Canada, the SAR limit for
mobile phones used by the public is 1.6 watts/kg
(W/kg) averaged over one gram of tissue. The
standard incorporates a substantial margin of
safety to give additional protection for the public
and to account for any variations in measure-
ments.
Health and Safety Information
163
SAR tests are conducted using standard operating
positions specified by the FCC with the phone
transmitting at its highest certified power level in all
tested frequency bands. Although the SAR is
determined at the highest certified power level, the
actual SAR level of the phone while operating can
be well below the maximum value. This is because
the phone is designed to operate at multiple power
levels so as to use only the power required to reach
the network. In general, the closer you are to a
wireless base station antenna, the lower the power
output of the phone.
Before a new model phone is available for sale to the
public, it must be tested and certified to the FCC that
it does not exceed the limit established by the
government adopted requirement for safe exposure.
The tests are performed in positions and locations
(e.g., at the ear and worn on the body) as required
by the FCC for each model. While there may be
differences between the SAR levels of various phones
and at various positions, they all meet the
government requirement.
The FCC has granted an Equipment Authorization for
this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this model
phone is on file with the FCC and can be found
under the Display Grant section of http://
www.fcc.gov/oet/fccid after searching on FCC ID
printed in the label on the phone.
Health and Safety Information
164
FCC certification information for this model phone is
attached separation paper.
For Body Operation
For body worn operation, this model phone has been
tested and meets the FCC RF exposure guidelines
when used with a Samsung-supplied or approved
accessory designated for this product or when used
with and accessory that contains no metal and that
positions the handset a minimum from the body.
The minimum distance for this model phone is written
in the FCC certification information from the body.
None compliance with the above conditions may
violate FCC RF exposure guidelines.
For more Information concerning exposure to radio
frequency signals, see the following websites:
Federal Communications Commission (FCC)
http://www.fcc.gov
Cellular Telecommunications Industry Association
(CTIA): http://www.wow-com.com
U.S.Food and Drug Administration (FDA)
http://www.fda.gov/cdrh/consumer
World Health Organization (WHO)
http://www.who.int/peh-emf/en
Precautions When Using Batteries
♦Never use any charger or battery that is damaged
in any way.
♦Use the battery only for its intended purpose.
♦If you use the phone near the network’s base
station, it uses less power; talk and standby time are
greatly affected by the signal strength on the
Health and Safety Information
165
cellular network and the parameters set by the
network operator.
♦Battery charging time depends on the remaining
battery charge, the type of battery and the
charger used. The battery can be charged and
discharged hundreds of times, but it will gradually
wear out. When the operation time (talk time and
standby time) is noticeably shorter than normal, it is
time to buy a new battery.
♦If left unused, a fully charged battery will discharge
itself over time.
♦Use only Samsung-approved batteries and
recharge your battery only with Samsung-
approved chargers. When a charger is not in use,
disconnect it from the power source.
♦Do not leave the battery connected to a charger
for more than a week, since overcharging may
shorten its life.
♦Extreme temperatures will affect the charging
capacity of your battery: it may require cooling or
warming first.
♦Do not leave the battery in hot or cold places, such
as in a car in summer or winter conditions, as you
will reduce the capacity and lifetime of the battery.
Always try to keep the battery at room
temperature. A phone with a hot or cold battery
may temporarily not work, even when the battery is
fully charged. Li-ion batteries are particularly
affected by temperatures below 0 C (32 F).
♦Do not short-circuit the battery. Accidental short-
circuiting can occur when a metallic object (coin,
clip or pen) causes a direct connection between
the + and terminals of the battery (metal strips on
the battery), for example when you carry a spare
battery in a pocket or bag. Shortcircuiting the
terminals may damage the battery or the object
causing the short-circuiting.
Health and Safety Information
166
♦Dispose of used batteries in accordance with local
regulations. Always recycle. Do not dispose of
batteries in a fire.
Road Safety
Your wireless phone gives you the powerful ability to
communicate by voice, almost anywhere, anytime.
But an important responsibility accompanies the
benefits of wireless phones, one that every user must
uphold.
When driving a car, driving is your first responsibility.
When using your wireless phone behind the wheel of
a car, practice good common sense and remember
the following tips:
♦Get to know your wireless phone and its features,
such as speed dial and redial. If available, these
features help you to place your call without taking
your attention off the road.
♦When available, use a hands-free device. If
possible, add an extra layer of convenience and
safety to your wireless phone with one of the many
hands-free accessories available today.
♦Position your wireless phone within easy reach. Be
able to access your wireless phone without
removing your eyes from the road. If you get an
incoming call at an inconvenient time, let your
voice mail answer it for you.
♦Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice and even heavy traffic can be
hazardous.
♦Do not take notes or look up phone numbers while
driving. Jotting down a To Do list or flipping through
Health and Safety Information
167
your phonebook takes your attention away from
your primary responsibility, driving safely.
♦Dial sensibly and assess the traffic; if possible, place
calls when you are not moving or before pulling
into traffic. Try to plan calls when your car will be
stationary. If you need to make a call while moving,
dial only a few numbers, check the road and your
mirrors, then continue.
♦Do not engage in stressful or emotional
conversations that may be distracting. Make the
people with whom you are talking aware that you
are driving and suspend conversations that have
the potential to divert your attention from the road.
♦Use your wireless phone to call for help. Dial the
emergency number in the case of fire, traffic
accident or medical emergencies. Remember, it is
a free call on your wireless phone!
♦Use your wireless phone to help others in
emergencies. If you see a car accident, crime in
progress or other serious emergency where lives are
in danger, call the emergency number, as you
would want others to do for you.
♦If you see a broken-down vehicle posing no serious
hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a
vehicle you know to be stolen, call roadside
assistance or any other special non-emergency
wireless number.
Operating Environment
Remember to follow any special regulations in force
in any area and always switch your phone off
whenever it is forbidden to use it, or when it may
cause interference or danger.
When connecting the phone or any accessory to
another device, read its user’s guide for detailed
Health and Safety Information
168
safety instructions. Do not connect incompatible
products.
As with other mobile radio transmitting equipment,
users are advised that for the satisfactory operation
of the equipment and for the safety of personnel, it is
recommended that the equipment should only be
used in the normal operating position (held to your
ear with the antenna pointing over your shoulder).
Electronic Devices
Most modern electronic equipment is shielded from
radio frequency (RF) signals. However, certain
electronic equipment may not be shielded against
the RF signals from your wireless phone. Consult the
manufacturer to discuss alternatives.
Pacemakers
Pacemaker manufacturers recommend that a
minimum distance of 15 cm (6 inches) be maintained
between a wireless phone and a pacemaker to
avoid potential interference with the pacemaker.
These recommendations are consistent with the
independent research and recommendations of
Wireless Technology Research.
Persons with pacemakers:
♦should always keep the phone more than 15 cm (6
inches) from their pacemaker when the phone is
switched on.
♦should not carry the phone in a breast pocket.
♦should use the ear opposite the pacemaker to
minimize potential interference.
Health and Safety Information
169
If you have any reason to suspect that interference is
taking place, switch your phone off immediately.
Hearing Aids
Some digital wireless phones may interfere with some
hearing aids. In the event of such interference, you
may wish to consult your hearing aid manufacturer
to discuss alternatives.
Other Medical Devices
If you use any other personal medical devices,
consult the manufacturer of your device to
determine if it is adequately shielded from external
RF energy. Your physician may be able to assist you in
obtaining this information. Switch your phone off in
health care facilities when any regulations posted in
these areas instruct you to do so. Hospitals or health
care facilities may be using equipment that could be
sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or
inadequately shielded electronic systems in motor
vehicles. Check with the manufacturer or its
representative regarding your vehicle. You should
also consult the manufacturer of any equipment that
has been added to your vehicle. You should also
consult the manufacturer of any equipment that has
been added to your vehicle.
Health and Safety Information
170
Posted Facilities
Switch your phone off in any facility where posted
notices require you to do so.
Potentially Explosive Environments
Switch your phone off when in any area with a
potentially explosive atmosphere and obey all signs
and instructions. Sparks in such areas could cause an
explosion or fire resulting in bodily injury or even
death.
Users are advised to switch the phone off while at a
refueling point (service station). Users are reminded
of the need to observe restrictions on the use of radio
equipment in fuel depots (fuel storage and
distribution areas), chemical plants or where blasting
operations are in progress.
Areas with a potentially explosive atmosphere are
often but not always clearly marked. They include
the areas below deck on boats, chemical transfer or
storage facilities, vehicles using liquefied petroleum
gas (such as propane or butane), areas where the air
contains chemicals or particles, such as grain, dust or
metal powders, and any other area where you
would normally be advised to turn off your vehicle
engine.
Emergency Calls
This phone, like any wireless phone, operates using
radio signals, wireless and landline networks as well as
user-programmed functions, which cannot
guarantee connection in all conditions. Therefore,
Health and Safety Information
171
you should never rely solely on any wireless phone for
essential communications (medical emergencies, for
example).
Remember, to make or receive any calls the phone
must be switched on and in a service area with
adequate signal strength. Emergency calls may not
be possible on all wireless phone networks or when
certain network services and/or phone features are
in use. Check with local service providers.
To make an emergency call:
1. If the phone is not on, switch it on.
2. Key in the emergency number for your present
location (for example, 911 or other official
emergency number). Emergency numbers vary
by location.
3. Press the <Send> key.
If certain features are in use (call barring, for
example), you may first need to deactivate those
features before you can make an emergency call.
Consult this document and your local cellular service
provider.
When making an emergency call, remember to give
all the necessary information as accurately as
possible. Remember that your phone may be the
only means of communication at the scene of an
accident; do not cut off the call until given
permission to do so.
Health and Safety Information
172
Other Important Safety Information
♦Only qualified personnel should service the phone
or install the phone in a vehicle. Faulty installation or
service may be dangerous and may invalidate any
warranty applicable to the device.
♦Check regularly that all wireless phone equipment
in your vehicle is mounted and operating properly.
♦Do not store or carry flammable liquids, gases or
explosive materials in the same compartment as
the phone, its parts or accessories.
♦For vehicles equipped with an air bag, remember
air bag inflates with great force. Do not place
including both installed or portable wireless
equipment the area over the air bag or in the air
bag deployment area. If wireless equipment is
improperly installed air bag inflates, serious injury
could result.
♦Switch your phone off before boarding an aircraft.
The use of wireless phones in aircraft is illegal and
may be dangerous to the aircraft’s operation.
♦Failure to observe these instructions may lead to
the suspension or denial of telephone services to
the offender, or legal action, or both.
Care and Maintenance
Your phone is a product of superior design and
craftsmanship and should be treated with care. The
suggestions help you fulfill any warranty obligations
and allow enjoy this product for many years:
♦Keep the phone and all its parts and accessories
reach of small children’s.
♦Keep the phone dry. Precipitation, humidity and
contain minerals that will corrode electronic
circuits.
Health and Safety Information
173
♦Do not use the phone with a wet hand. Doing so
may cause an electric shock to you or damage to
the phone.
♦Do not use or store the phone in dusty, dirty moving
parts may be damaged.
♦Do not store the phone in hot areas. High
temperatures can shorten the life of electronic
devices, damage batteries, and warp or melt
certain plastics.
♦Do not store the phone in cold areas. When the
phone warms up to its normal operating
temperature, moisture can form inside the phone,
which may damage the phone’s electronic circuit
boards.
♦Do not drop, knock or shake the phone. Rough
handling can break internal circuit boards.
♦Do not use harsh chemicals, cleaning solvents or
strong detergents to clean the phone. Wipe it with
a soft cloth slightly dampened in a mild soap-and-
water solution.
♦Do not paint the phone. Paint can clog the
device’s moving parts and prevent proper
operation.
♦Do not put the phone in or on heating devices,
such as a microwave oven, a stove or a radiator.
The phone may explode when overheated.
♦Use only the supplied or an approved replacement
antenna. Unauthorized antennas or modified
accessories may damage the phone and violate
regulations governing radio devices.
♦If the phone, battery, charger or any accessory is
not working properly, take it to your nearest
qualified service facility. The personnel there will
assist you, and if necessary, arrange for service.
Health and Safety Information
174
Acknowledging Special Precautions and the FCC and
Industry Canada Notice
Cautions
Modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
FCC Compliance Information
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference,
and
2. This device must accept any interference
received.
Including interference that may cause undesired
operation.
Information to User
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
Health and Safety Information
175
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
♦Reorient or relocate the receiving antenna.
♦Increase the separation between the equipment
and receiver.
♦Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
♦Consult the dealer or an experienced radio/ TV
technician for help.
Appendix A: CERTIFICATION INFORMATION (SAR)
THIS MODEL PHONE MEETS THE GOVERNMENT’S
REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.
Your wireless phone is a radio transmitter and
receiver. It is designed and manufactured not to
exceed the emission limits for exposure to radio
frequency (RF) energy set by the Federal
Communications Commission of the U.S.
Government. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy
for the general population. The guidelines are based
on safety standards that were developed by
independent scientific organizations through
periodic and thorough evaluation of scientific
studies. The standards include a substantial safety
margin designed to assure the safety of all persons,
regardless of age and health.
Health and Safety Information
176
The exposure standard for wireless mobile phones
employs a unit of measurement known as the
Specific Absorption Rate (SAR). The SAR limit set by
the FCC is 1.6 W/kg. SAR Tests are conducted using
standard operating positions accepted by the FCC
with the phone transmitting at its highest certified
power level in all tested frequency bands. Although
the SAR is determined at the highest certified power
level, the actual SAR level of the phone while
operating can be well below the maximum value.
This is because the phone is designed to operate at
multiple power levels so as to use only the power
required to reach the network. In general, the closer
you are to a wireless base station antenna, the lower
the power output.
Before a new model phone is available for sale to the
public, it must be tested and certified to the FCC that
it does not exceed the limit established by the
government adopted requirement for safe exposure.
The tests are performed in positions and
locations(e.g., at the ear and worn on the body) as
required by the FCC for each model.
The highest SAR values of this model phone as
reported to FCC are Head: 1.440 W/kg, Body-worn:
1.300 W/kg in GSM 850 and Head: 0.663 W/kg, Body-
worn: 0.449 W/kg in GSM 1900.
Body-worn operations are restricted to Samsung-
supplied, approved or none Samsung designated
accessories that have no metal and must provide at
least 1.5cm separation between the device,
including its antenna whether extended or retracted,
Health and Safety Information
177
and the user’s body. None compliance to the above
restrictions may violate FCC RF exposure guidelines.
The FCC has granted an Equipment Authorization for
this model phone with all reported SAR levels
evaluated as in compliance with the FCC RF
exposure guidelines. SAR information on this model
phone is on file with the FCC and can be found
under the Display Grant section of http://
www.fcc.gov/oet/fccid after searching on FCC ID
A3LSGHE316.
In the United States and Canada, the SAR limit for
mobile phones used by the public is 1.6 watts/kilogram
(W/kg) averaged over one gram of tissue. The standard
incorporates a substantial ma gin of safety to give addi-
tional protection for the public and to account for any
variations in measurements.
Appendix B: Guide to Safe and Responsible Wireless
Phone Use
Cellular Telecommunications & Internet Association
“Safety is the most important call you will ever make.”
Health and Safety Information
178
A Guide to Safe and Responsible Wireless Phone Use
TENS OF MILLIONS OF PEOPLE IN THE U.S. TODAY TAKE
ADVANTAGE OF THE UNIQUE COMBINATION OF
CONVENIENCE, SAFETY AND VALUE DELIVERED BY THE
WIRELESS TELEPHONE. QUITE SIMPLY, THE WIRELESS
PHONE GIVES PEOPLE THE POWERFUL ABILITY TO
COMMUNICATE BY VOICE-ALMOST ANYWHERE,
ANYTIMEWITH THE BOSS, WITH A CLIENT, WITH THE KIDS,
WITH EMERGENCY PERSONNEL OR EVEN WITH THE
POLICE. EACH YEAR, AMERICANS MAKE BILLIONS OF
CALLS FROM THEIR WIRELESS PHONES, AND THE
NUMBERS ARE RAPIDLY GROWING.
But an important responsibility accompanies those
benefits, one that every wireless phone user must
uphold. When driving a car, driving is your first
responsibility. A wireless phone can be an invaluable
tool, but good judgment must be exercised at all
times while driving a motor vehicle whether on the
phone or not.
The basic lessons are ones we all learned as
teenagers. Driving requires alertness, caution and
courtesy. It requires a heavy dose of basic common
sense-keep your head up, keep your eyes on the
road, check your mirrors frequently and watch out for
other drivers. It requires obeying all traffic signs and
signals and staying within the speed limit. It means
using seat belts and requiring other passengers to do
the same.
But with wireless phone use, driving safely means a
little more. This brochure is a call to wireless phone
Health and Safety Information
179
users everywhere to make safety their first priority
when behind the wheel of a car. Wireless
telecommunications is keeping us in touch,
simplifying our lives, protecting us in emergencies
and providing opportunities to help others in need.
When it comes to the use of wireless phones, safety is
your most important call.
Wireless Phone “Safety Tips”
Below are safety tips to follow while driving and using
a wireless phone which should be easy to remember:
1. Get to know your wireless phone and its features
such as speed dial and redial. Carefully read your
instruction manual and learn to take advantage
of valuable features most phones offer, including
automatic redial and memory. Also, work to
memorize the phone keypad so you can use the
speed dial function without taking your attention
off the road.
2. When available, use a hands free device. A
number of hands free wireless phone accessories
are readily available today. Whether you choose
an installed mounted device for your wireless
phone or a speaker phone accessory, take
advantage of these devices if available to you.
3. Position your wireless phone within easy reach.
Make sure you place your wireless phone within
easy reach and where you can grab it without
removing your eyes from the road. If you get an
Health and Safety Information
180
incoming call at an inconvenient time, if possible,
let your voice mail answer it for you.
4. Suspend conversations during hazardous driving
conditions or situations. Let the person you are
speaking with know you are driving; if necessary,
suspend the call in heavy traffic or hazardous
weather conditions. Rain, sleet, snow and ice can
be hazardous, but so is heavy traffic. As a driver,
your first responsibility is to pay attention to the
road.
5. Do not take notes or look up phone numbers while
driving. If you are reading an address book or
business card, or writing a to do list while driving a
car, you are not watching where you are going.
It’s common sense. Don’t get caught in a
dangerous situation because you are reading or
writing and not paying attention to the road or
nearby vehicles.
6. Dial sensibly and assess the traffic; if possible,
place calls when you are not moving or before
pulling into traffic. Try to plan your calls before you
begin your trip or attempt to coincide your calls
with times you may be stopped at a stop sign, red
light or otherwise stationary. But if you need to dial
while driving, follow this simple tip-dial only a few
numbers, check the road and your mirrors, then
continue.
7. Do not engage in stressful or emotional
conversations that may be distracting. Stressful or
emotional conversations and driving do not mix-
Health and Safety Information
181
they are distracting and even dangerous when
you are behind the wheel of a car. Make people
you are talking with aware you are driving and if
necessary, suspend conversations which have the
potential to divert your attention from the road.
8. Use your wireless phone to call for help. Your
wireless phone is one of the greatest tools you can
own to protect yourself and your family in
dangerous situations-with your phone at your side,
help is only three numbers away. Dial 9-1-1 or
other local emergency number in the case of fire,
traffic accident, road hazard or medical
emergency. Remember, it is a free call on your
wireless phone!
9. Use your wireless phone to help others in
emergencies. Your wireless phone provides you a
perfect opportunity to be a Good Samaritan in
your community. If you see an auto accident,
crime in progress or other serious emergency
where lives are in danger, call 9-1-1 or other local
emergency number, as you would want others to
do for you.
10.Call roadside assistance or a special wireless non
emergency assistance number when necessary.
Certain situations you encounter while driving may
require attention, but are not urgent enough to
merit a call for emergency services. But you still
can use your wireless phone to lend a hand. If you
see a broken-down vehicle posing no serious
hazard, a broken traffic signal, a minor traffic
Health and Safety Information
182
accident where no one appears injured or a
vehicle you know to be stolen, call roadside
assistance or other special non-emergency
wireless number.
Careless, distracted individuals and people driving
irresponsibly represent a hazard to everyone on the
road. Since 1984, the Cellular Telecommunications
Industry Association and the wireless industry have
conducted educational outreach to inform wireless
phone users of their responsibilities as safe drivers and
good citizens. As we approach a new century, more
and more of us will take advantage of the benefits of
wireless telephones. And, as we take to the roads, we
all have a responsibility to drive safely.
The wireless industry reminds you to use your phone
safely when driving.
Cellular Telecommunications & Internet Association
For more information, please call 1-888-901-SAFE.
For updates: http://www.wow-com.com/consumer/
issues/driving/articles.cfm?ID =85
Appendix C: Consumer Update on Wireless Phones
U.S. Food and Drug Administration
1. What kinds of phones are the subject of this
update?
The term wireless phone refers here to hand-held
wireless phones with built-in antennas, often called
cell, mobile, or PCS phones. These types of wireless
phones can expose the user to measurable radio
frequency energy (RF) because of the short distance
Health and Safety Information
183
between the phone and the user s head. These RF
exposures are limited by Federal Communications
Commission safety guidelines that were developed
with the advice of FDA and other federal health and
safety agencies. When the phone is located at
greater distances from the user, the exposure to RF is
drastically lower because a person’s RF exposure
decreases rapidly with increasing distance from the
source. The so-called “cordless phones,” which have
a base unit connected to the telephone wiring in a
house, typically operate at far lower power levels,
and thus produce RF exposures well within the FCC’s
compliance limits.
2. Do wireless phones pose a health hazard?
The available scientific evidence does not show that
any health problems are associated with using
wireless phones. There is no proof, however, that
wireless phones are absolutely safe. Wireless phones
emit low levels of radio frequency energy (RF) in the
microwave range while being used. They also emit
very low levels of RF when in the stand-by mode.
Whereas high levels of RF can produce health effects
(by heating tissue), exposure to low level RF that does
not produce heating effects causes no known
adverse health effects. Many studies of low level RF
exposures have not found any biological effects.
Some studies have suggested that some biological
effects may occur, but such findings have not been
confirmed by additional research. In some cases,
other researchers have had difficulty in reproducing
Health and Safety Information
184
those studies, or in determining the reasons for
inconsistent results.
3. What is FDA’s role concerning the safety of
wireless phones?
Under the law, FDA does not review the safety of
radiation emitting consumer products such as
wireless phones before they can be sold, as it does
with new drugs or medical devices. However, the
agency has authority to take action if wireless
phones are shown to emit radio frequency energy
(RF) at a level that is hazardous to the user. In such a
case, FDA could require the manufacturers of
wireless phones to notify users of the health hazard
and to repair, replace or recall the phones so that
the hazard no longer exists.
Although the existing scientific data do not justify FDA
regulatory actions, FDA has urged the wireless phone
industry to take a number of steps, including the
following:
♦Support needed research into possible biological
effects of RF of the type emitted by wireless phones;
♦Design wireless phones in a way that minimizes any
RF exposure to the user that is not necessary for
device function; and
♦Cooperate in providing users of wireless phones
with the best possible information on possible
effects of wireless phone use on human health
FDA belongs to an interagency working group of the
federal agencies that have responsibility for different
aspects of RF safety to ensure coordinated efforts at
Health and Safety Information
185
the federal level. The following agencies belong to
this working group:
♦National Institute for Occupational Safety and
Health
♦Environmental Protection Agency Federal
Communications Commission
♦Occupational Safety and Health Administration
♦National Telecommunications and Information
Administration
♦The National Institutes of Health participates in
some interagency working group activities, as well.
FDA shares regulatory responsibilities for wireless
phones with the Federal Communications
Commission (FCC). All phones that are sold in the
United States must comply with FCC safety guidelines
that limit RF exposure. FCC relies on FDA and other
health agencies for safety questions about wireless
phones.
FCC also regulates the base stations that the wireless
phone networks rely upon. While these base stations
operate at higher power than do the wireless phones
themselves, the RF exposures that people get from
these base stations are typically thousands of times
lower than those they can get from wireless phones.
Base stations are thus not the primary subject of the
safety questions discussed in this document.
4. What is FDA doing to find out more about the
possible health effects of wireless phone RF?
FDA is working with the U.S. National Toxicology
Program and with groups of investigators around the
world to ensure that high priority animal studies are
Health and Safety Information
186
conducted to address important questions about the
effects of exposure to radio frequency energy (RF).
FDA has been a leading participant in the World
Health Organization International Electromagnetic
Fields (EMF) Project since its inception in 1996. An
influential result of this work has been the
development of a detailed agenda of research
needs that has driven the establishment of new
research programs around the world. The Project has
also helped develop a series of public information
documents on EMF issues.
FDA and the Cellular Telecommunications & Internet
Association (CTIA) have a formal Cooperative
Research and Development Agreement (CRADA) to
do research on wireless phone safety. FDA provides
the scientific oversight, obtaining input from experts
in government, industry, and academic
organizations. CTIA-funded research is conducted
through contracts to independent investigators. The
initial research will include both laboratory studies
and studies of wireless phone users. The CRADA will
also include a broad assessment of additional
research needs in the context of the latest research
developments around the world.
5. What steps can I take to reduce my exposure to
radio frequency energy from my wireless phone?
If there is a risk from these products—and at this point
we do not know that there is—it is probably very
small. But if you are concerned about avoiding even
potential risks, you can take a few simple steps to
minimize your exposure to radio frequency energy
Health and Safety Information
187
(RF). Since time is a key factor in how much exposure
a person receives, reducing the amount of time
spent using a wireless phone will reduce RF exposure.
If you must conduct extended conversations by
wireless phone every day, you could place more
distance between your body and the source of the
RF, since the exposure level drops off dramatically
with distance. For example, you could use a headset
and carry the wireless phone away from your body or
use a wireless phone connected to a remote
antenna
Again, the scientific data do not demonstrate that
wireless phones are harmful. But if you are
concerned about the RF exposure from these
products, you can use measures like those described
above to reduce your RF exposure from wireless
phone use.
6. What about children using wireless phones?
The scientific evidence does not show a danger to
users of wireless phones, including children and
teenagers. If you want to take steps to lower
exposure to radio frequency energy (RF), the
measures described above would apply to children
and teenagers using wireless phones. Reducing the
time of wireless phone use and increasing the
distance between the user and the RF source will
reduce RF exposure.
Some groups sponsored by other national
governments have advised that children be
discouraged from using wireless phones at all. For
Health and Safety Information
188
example, the government in the United Kingdom
distributed leaflets containing such a
recommendation in December 2000. They noted
that no evidence exists that using a wireless phone
causes brain tumors or other ill effects. Their
recommendation to limit wireless phone use by
children was strictly precautionary; it was not based
on scientific evidence that any health hazard exists.
7. Do hands-free kits for wireless phones reduce risks
from exposure to RF emissions?
Since there are no known risks from exposure to RF
emissions from wireless phones, there is no reason to
believe that hands-free kits reduce risks. Hands-free
kits can be used with wireless phones for
convenience and comfort. These systems reduce the
absorption of RF energy in the head because the
phone, which is the source of the RF emissions, will
not be placed against the head. On the other hand,
if the phone is mounted against the waist or other
part of the body during use, then that part of the
body will absorb more RF energy. Wireless phones
marketed in the U.S. are required to meet safety
requirements regardless of whether they are used
against the head or against the body. Either
configuration should result in compliance with the
safety limit.
8. Do wireless phone accessories that claim to shield
the head from RF radiation work?
Since there are no known risks from exposure to RF
emissions from wireless phones, there is no reason to
Health and Safety Information
189
believe that accessories that claim to shield the
head from those emissions reduce risks. Some
products that claim to shield the user from RF
absorption use special phone cases, while others
involve nothing more than a metallic accessory
attached to the phone. Studies have shown that
these products generally do not work as advertised.
Unlike “hand-free” kits, these so-called “shields” may
interfere with proper operation of the phone. The
phone may be forced to boost its power to
compensate, leading to an increase in RF
absorption. In February 2002, the Federal trade
Commission (FTC) charged two companies that sold
devices that claimed to protect wireless phone users
from radiation with making false and unsubstantiated
claims. According to FTC, these defendants lacked a
reasonable basis to substantiate their claim.
9. What about wireless phone interference with
medical equipment?
Radio frequency energy (RF) from wireless phones
can interact with some electronic devices. For this
reason, FDA helped develop a detailed test method
to measure electromagnetic interference (EMI) of
implanted cardiac pacemakers and defibrillators
from wireless telephones. This test method is now part
of a standard sponsored by the Association for the
Advancement of Medical instrumentation (AAMI).
The final draft, a joint effort by FDA, medical device
manufacturers, and many other groups, was
completed in late 2000. This standard will allow
Health and Safety Information
190
manufacturers to ensure that cardiac pacemakers
and defibrillators are safe from wireless phone EMI.
FDA has tested hearing aids for interference from
handheld wireless phones and helped develop a
voluntary standard sponsored by the Institute of
Electrical and Electronic Engineers (IEEE). This
standard specifies test methods and performance
requirements for hearing aids and wireless phones so
that no interference occurs when a person uses a
compatible phone and a compatible hearing aid at
the same time. This standard was approved by the
IEEE in 2000.
FDA continues to monitor the use of wireless phones
for possible interactions with other medical devices.
Should harmful interference be found to occur, FDA
will conduct testing to assess the interference and
work to resolve the problem.
10.What are the results of the research done
already?
The research done thus far has produced conflicting
results, and many studies have suffered from flaws in
their research methods. Animal experiments
investigating the effects of radio frequency energy
(RF) exposures characteristic of wireless phones have
yielded conflicting results that often cannot be
repeated in other laboratories. A few animal studies,
however, have suggested that low levels of RF could
accelerate the development of cancer in laboratory
animals. However, many of the studies that showed
increased tumor development used animals that
had been genetically engineered or treated with
Health and Safety Information
191
cancer causing chemicals so as to be pre-disposed
to develop cancer in the absence of RF exposure.
Other studies exposed the animals to RF for up to 22
hours per day. These conditions are not similar to the
conditions under which people use wireless phones,
so we don’ t know with certainty what the results of
such studies mean for human health.
Three large epidemiology studies have been
published since December 2000. Between them, the
studies investigated any possible association
between the use of wireless phones and primary
brain cancer, gioma, meningioma, or acoustic
neuroma, tumors of the brain or salivary gland,
leukemia, or other cancers. None of the studies
demonstrated the existence of any harmful health
effects from wireless phone RF exposures. However,
none of the studies can answer questions about
long-term exposures, since the average period of
phone use in these studies was around three years.
11.What research is needed to decide whether RF
exposure from wireless phones poses a health risk?
A combination of laboratory studies and
epidemiological studies of people actually using
wireless phones would provide some of the data that
are needed. Lifetime animal exposure studies could
be completed in a few years. However, very large
numbers of animals would be needed to provide
reliable proof of a cancer promoting effect if one
exists. Epidemiological studies can provide data that
is directly applicable to human populations, but 10 or
more years follow-up may be needed to provide
Health and Safety Information
192
answers about some health effects, such as cancer.
This is because the interval between the time of
exposure to a cancer-causing agent and the time
tumors develop - if they do - may be many, many
years. The interpretation of epidemiological studies is
hampered by difficulties in measuring actual RF
exposure during day-to-day use of wireless phones.
Many factors affect this measurement, such as the
angle at which the phone is held, or which model of
phone is used.
12.Which other federal agencies have responsibilities
related to potential RF health effects?
Additional information on the safety of RF exposures
from various sources can be obtained from the
following organizations.
FCC RF Safety Program:
http://www.fcc.gov/oet/rfsafety/
Environmental Protection Agency (EPA):
http://www.epa.gov/radiation/
Occupational Safety and Health Administration’s
(OSHA):
http://www.osha-slc.gov/SLTC/
radiofrequencyradiation/index.html
National Institute for Occupational Safety and Health
(NIOSH):
http://www.cdc.gov/niosh/emfpg.html
World health Organization (WHO):
http://www.who.int/peh-emf/
Health and Safety Information
193
International Commission on Non-Ionizing Radiation
Protection:
http://www.icnirp.de
National Radiation Protection Board (UK):
http://www.nrpb.org.uk
Updated 4/3/2002: US Food and Drug Administration
http://www.fda.gov/cellphones
Health and Safety Information
194
STANDARD LIMITED WARRANTY
What is Covered and For How Long? SAMSUNG
TELECOMMUNICATIONS AMERICA, L.P. (SAMSUNG)
warrants to the original purchaser ("Purchaser") that
SAMSUNG’s Phones and accessories ("Products") are
free from defects in material and workmanship under
normal use and service for the period commencing
upon the date of purchase and continuing for the
following specified period of time after that date:
Phone
1 Year
Batteries
1 Year
Leather Case/Pouch
Holster
90 Days
90 Days
1 Year
Other Phone Accessories
What is Not Covered? This Limited Warranty is
conditioned upon proper use of Product by
Purchaser. This Limited Warranty does not cover: (a)
defects or damage resulting from accident, misuse,
abuse, neglect, unusual physical, electrical or
electromechanical stress, or modification of any part
of Product, including antenna, or cosmetic damage;
(b) equipment that has the serial number removed or
made illegible; (c) any plastic surfaces or other
externally exposed parts that are scratched or
damaged due to normal use; (d) malfunctions
STANDARD LIMITED WARRANTY
195
resulting from the use of Product in conjunction with
accessories, products, or ancillary/peripheral
equipment not furnished or approved by SAMSUNG;
(e) defects or damage from improper testing,
operation, maintenance, installation, or adjustment;
(f) installation, maintenance, and service of Product,
or (g) Product used or purchased outside the United
States or Canada.
This Limited Warranty covers batteries only if battery
capacity falls below 80% of rated capacity or the
battery leaks, and this Limited Warranty does not
cover any battery if (i) the battery has been charged
by a battery charger not specified or approved by
SAMSUNG for charging the battery, (ii) any of the
seals on the battery are broken or show evidence of
tampering, or (iii) the battery has been used in
equipment other than the SAMSUNG phone for
which it is specified.
What are SAMSUNG’s Obligations? During the
applicable warranty period, SAMSUNG will repair or
replace, at SAMSUNG’s sole option, without charge
to Purchaser, any defective component part of
Product. To obtain service under this Limited
Warranty, Purchaser must return Product to an
authorized phone service facility in an adequate
container for shipping, accompanied by Purchaser’s
sales receipt or comparable substitute proof of sale
showing the date of purchase, the serial number of
Product and the sellers’ name and address. To
obtain assistance on where to deliver the Product,
call Samsung Customer Care at 1-888-987-4357.
Upon receipt, SAMSUNG will promptly repair or
STANDARD LIMITED WARRANTY
196
replace the defective Product. SAMSUNG may, at
SAMSUNG’s sole option, use rebuilt, reconditioned, or
new parts or components when repairing any
Product or replace Product with a rebuilt,
reconditioned or new Product. Repaired/replaced
leather cases, pouches and holsters will be
warranted for a period of ninety (90) days. All other
repaired/replaced Product will be warranted for a
period equal to the remainder of the original Limited
Warranty on the original Product or for 90 days,
whichever is longer. All replaced parts, components,
boards and equipment shall become the property of
SAMSUNG. If SAMSUNG determines that any Product
is not covered by this Limited Warranty, Purchaser
must pay all parts, shipping, and labor charges for
the repair or return of such Product.
What Are the Limits On SAMSUNG’s Liability? EXCEPT
AS SET FORTH IN THE EXPRESS WARRANTY CONTAINED
HEREIN, PURCHASER TAKES THE PRODUCT “AS IS,” AND
SAMSUNG MAKES NO WARRANTY OR
REPRESENTATION AND THERE ARE NO CONDITIONS,
EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, OF
ANY KIND WHATSOEVER WITH RESPECT TO THE
PRODUCT, INCLUDING BUT NOT LIMITED TO:
♦THE MERCHANTABILITY OF THE PRODUCT OR ITS
FITNESS FOR ANY PARTICULAR PURPOSE OR USE;
♦WARRANTIES OF TITLE OR NON-INFRINGEMENT;
♦DESIGN, CONDITION, QUALITY, OR PERFORMANCE
OF THE PRODUCT;
♦THE WORKMANSHIP OF THE PRODUCT OR THE
COMPONENTS CONTAINED THEREIN; OR
STANDARD LIMITED WARRANTY
197
♦COMPLIANCE OF THE PRODUCT WITH THE
REQUIREMENTS OF ANY LAW, RULE, SPECIFICATION
OR CONTRACT PERTAINING THERETO.
NOTHING CONTAINED IN THE INSTRUCTION MANUAL
SHALL BE CONSTRUED TO CREATE AN EXPRESS
WARRANTY OF ANY KIND WHATSOEVER WITH RESPECT
TO THE PRODUCT. ALL IMPLIED WARRANTIES AND
CONDITIONS THAT MAY ARISE BY OPERATION OF LAW,
INCLUDING IF APPLICABLE THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY LIMITED TO THE SAME
DURATION OF TIME AS THE EXPRESS WRITTEN
WARRANTY STATED HEREIN. SOME STATES/PROVINCES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION
MAY NOT APPLY TO YOU. IN ADDITION, SAMSUNG
SHALL NOT BE LIABLE FOR ANY DAMAGES OF ANY
KIND RESULTING FROM THE PURCHASE, USE, OR
MISUSE OF, OR INABILITY TO USE THE PRODUCT OR
ARISING DIRECTLY OR INDIRECTLY FROM THE USE OR
LOSS OF USE OF THE PRODUCT OR FROM THE BREACH
OF THE EXPRESS WARRANTY, INCLUDING INCIDENTAL,
SPECIAL, CONSEQUENTIAL OR SIMILAR DAMAGES, OR
LOSS OF ANTICIPATED PROFITS OR BENEFITS, OR FOR
DAMAGES ARISING FROM ANY TORT (INCLUDING
NEGLIGENCE OR GROSS NEGLIGENCE) OR FAULT
COMMITTED BY SAMSUNG, ITS AGENTS OR
EMPLOYEES, OR FOR ANY BREACH OF CONTRACT OR
FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY
ANY OTHER PARTY. SOME STATES/PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
STANDARD LIMITED WARRANTY
198
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH
VARY FROM STATE TO STATE/PROVINCE TO PROVINCE.
THIS LIMITED WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL PURCHASER OF
THIS PRODUCT AND STATES PURCHASER’S EXCLUSIVE
REMEDY. IF ANY PORTION OF THIS LIMITED WARRANTY
IS HELD ILLEGAL OR UNENFORCEABLE BY REASON OF
ANY LAW, SUCH PARTIAL ILLEGALITY OR
UNENFORCEABILITY SHALL NOT AFFECT THE
ENFORCEABILITY FOR THE REMAINDER OF THIS LIMITED
WARRANTY WHICH PURCHASER ACKNOWLEDGES IS
AND WILL ALWAYS BE CONSTRUED TO BE LIMITED BY ITS
TERMS OR AS LIMITED AS THE LAW PERMITS.
THE PARTIES UNDERSTAND THAT THE PURCHASER MAY
USE THIRD-PARTY SOFTWARE OR EQUIPMENT IN
CONJUNCTION WITH THE PRODUCT. SAMSUNG
MAKES NO WARRANTIES OR REPRESENTATIONS AND
THERE ARE NO CONDITIONS, EXPRESS OR IMPLIED,
STATUTORY OR OTHERWISE, AS TO THE QUALITY,
CAPABILITIES, OPERATIONS, PERFORMANCE OR
SUITABILITY OF ANY THIRD-PARTY SOFTWARE OR
EQUIPMENT, WHETHER SUCH THIRD-PARTY SOFTWARE
OR EQUIPMENT IS INCLUDED WITH THE PRODUCT
DISTRIBUTED BY SAMSUNG OR OTHERWISE, INCLUDING
THE ABILITY TO INTEGRATE ANY SUCH SOFTWARE OR
EQUIPMENT WITH THE PRODUCT. THE QUALITY,
CAPABILITIES, OPERATIONS, PERFORMANCE AND
SUITABILITY OF ANY SUCH THIRD-PARTY SOFTWARE OR
EQUIPMENT LIE SOLELY WITH THE PURCHASER AND THE
STANDARD LIMITED WARRANTY
199
DIRECT VENDOR, OWNER OR SUPPLIER OF SUCH
THIRD-PARTY SOFTWARE OR EQUIPMENT, AS THE CASE
MAY BE.
This Limited Warranty allocates risk of Product failure
between Purchaser and SAMSUNG, and SAMSUNG’s
Product pricing reflects this allocation of risk and the
limitations of liability contained in this Limited
Warranty. The agents, employees, distributors, and
dealers of SAMSUNG are not authorized to make
modifications to this Limited Warranty, or make
additional warranties binding on SAMSUNG.
Accordingly, additional statements such as dealer
advertising or presentation, whether oral or written,
do not constitute warranties by SAMSUNG and
should not be relied upon.
Samsung Telecommunications America, L.P.
1301 East Lookout Drive
Richardson, TX 75082
Phone: 1-800-SAMSUNG
Phone: 1-888-987-HELP (4357)
©2004 Samsung Telecommunications America, L.P.
All rights reserved.
No reproduction in whole or in part allowed without
prior written approval.
Specifications and availability subject to change
without notice. [080802]
STANDARD LIMITED WARRANTY
200
Glossary
To help you understand the main technical terms
and abbreviations used in this booklet, and to take
full advantage of the features of your mobile phone,
here are a few definitions:
Active Folder
Ability to answer a call simply by opening the phone.
Call Forwarding
Ability to reroute calls to another number.
Call Holding
Ability to put one call on standby while answering or
making another call; you can then switch between
the two calls, as required.
Call Waiting
Informs you that you have an incoming call when
you are engaged on another call.
Caller Line Identification Services (Caller ID)
Services allowing subscribers to view or block the
telephone numbers of callers.
Dual Band
Ability to handle any of the following types of
network: GSM 850 and GSM 1900 MHz bands, for
greater call success and wider roaming.
Glossary
201
EMS (Enhanced Message Service)
An adaptation of the Short Message Service (SMS)
that allows you to send and receive ring tones and
the service provider’s logo, as well as combinations
of simple media to and from EMS-compliant
handsets. Because EMS is based on SMS, it can use
SMS centers the same way that SMS does. EMS works
on all Global System for Mobile communications
(GSM) networks. EMS senders can use text, melodies,
pictures, sounds, and animations to enhance the
expressive power of messages that are limited by the
display constraints of mobile devices.
GPRS (General Packet Radio Service)
New non-voice value-added service that allows
information to be sent and received across a mobile
telephone network. GPRS provides continuous
connection to the Internet for mobile phone and
computer users. It is based on the Global System for
Mobile Communication (GSM) circuit-switched
cellular phone connections and the Short Message
Service (SMS).
GSM (Global System for Mobile Communication)
International standard for cellular communication,
guaranteeing compatibility between the various
network operators. GSM covers most European
countries and many other parts of the world.
Java
Programming language generating applications that
can run on all hardware platforms, whether small,
medium or large, without modification. It has been
Glossary
202
promoted for and geared heavily to the Web, both
for public Web sites and Intranets. When a Java
program runs from a Web page, it is called a Java
applet. When it is run on a mobile phone or pager, it
is called a MIDlet.
MMS (Multimedia Message Service)
A message service for the mobile environment,
standardized by the WAP Forum and the 3rd
Generation Partnership Program (3GPP). For phone
users, MMS is similar to Short Message Service (SMS)-it
provides automatic, immediate delivery of user-
created content from phone to phone. The message
addressing used is primarily phone numbers, thus the
traffic goes from phone to phone. MMS also provides
support for e-mail addressing, so that messages can
be sent by e-mail. In addition to the text content of
SMS, MMS messages can contain still images, voice
or audio clips, and also video clips and presentation
information.
Multi-party Calling
Ability to establish a conference call involving up to
five additional parties.
Phone Password
Security code used to unlock the phone when you
have selected the option to lock it automatically
each time it switches on.
PIN (Personal Identification Number)
Security code that protects the phone against
unauthorized use. The PIN is supplied by the service
Glossary
203
provider with the SIM card. It may be a four to eight-
digit number and can be changed, as required.
PUK (PIN Unblocking Key)
Security code used to unlock the phone when an
incorrect PIN has been entered three times in
succession. The eight-digit number is supplied by the
service provider with the SIM card.
Roaming
Use of your phone when you are outside your home
area (when traveling for example).
SDN (Service Dialing Numbers)
Telephone numbers supplied by your network
provider and giving access to special services, such
as voice mail, directory inquiries, customer support
and emergency services.
SIM (Subscriber Identification Module)
Card containing a chip with all the information
required to operate the phone (network and
memory information, as well as the subscriber’s
personal data). The SIM card fits into a small slot on
the back of the phone and is protected by the
battery.
SMS (Short Message Service)
Network service sending and receiving messages to
and from another subscriber without having to speak
to the correspondent. The message created or
received can be displayed, received, edited or sent.
Glossary
204
Soft Keys
Two keys marked
purpose of which:
and
on the phone, the
♦varies according to the function that you are
currently using.
♦is indicated on the bottom line of the display just
above the corresponding key.
Voice Mail
Computerised answering service that automatically
answers your calls when you are not available, plays
a greeting (optionally in your own voice) and records
a message.
Glossary
205
Glossary
206
Index
Caller groups
A
Calls
Answering
making •,
B
Camera
CB (Cell Broadcast) messages •,
Backlight
Battery
charging •,
D
Deleting
C
Calendar memos
copying •,
Call records
dialed •,
Index
207
Inbox, messages
Display
icons •,
J
K
Keypad tones
Keys
E
Emergency calls •,
EMS (Enhanced Message Service)
•
,
L
F
Locking
FDN (Fixed Dial Number) mode •,
Forwarding
M
Memory status
G
Menus
H
Messages
I
Index
208
text •,
layout •,
MMS (Multimedia Message Service)
unpacking •,
•,
Phone Book
Multimedia messages
copying •,
editing •,
Muting
Photos
PIN
PIN2
N
Names
PUK •,
Numbers, phone
O
R
Outbox, messages
Received messages
Recording
P
Redialing
Phone
Index
209
Text, enter •,
Tone
S
Safety
information •,
SDN (Service Dialing Numbers) •,
Sent messages
U
SIM card
V
SMS (Short Message Service)
Video
Voice memos
Switching on/off
Volume, adjust
T
Tasks, to do list
Templates
W
WAP browser
Text messages
Index
210
Index
212
213
214
|