Samsung Cell Phone S5 User Manual

Available applications and services are subject to change at any time.  
Get Started  
The following topics give you all the information you need to set up your phone and Sprint service the  
first time.  
Your Phone at a Glance  
The following illustration outlines your phone’s primary features.  
Set Up Your Phone  
Before using your new phone, you must install and charge the battery.  
Note: Your phone’s battery should have enough charge to turn the phone on and find a signal,  
complete the setup wizard, set up voicemail, and make a call. You should fully charge the battery as  
soon as possible.  
Install the Battery  
1. Using the slot provided, gently lift the cover off the phone.  
2. Insert the battery, aligning the gold contacts on the battery with the gold contacts on the phone,  
and gently press the battery into place.  
Get Started  
1
       
3. Replace the battery compartment cover, making sure all the tabs are secure and there are no  
gaps around the cover.  
Important: Before closing the cover, check to see if there is any foreign substance such as dust or  
sand between the rubber on the back of the cover and the sealing area.  
Note: Water-resistant and dustproof based on IP67 rating, which tests submersion up to 1 meter for  
up to 30 minutes. Not shockproof. Covers must be tightly closed.  
Maintaining Water and Dust Resistance  
This device is rated IP67 using the Ingress Protection rating system. The dust rating is 6 (highest  
level of protection) and the water resistance rating is 7 (water resistant up to 1 meter for up to 30  
minutes). Despite this classification, your device is not impervious to water damage in any situation.  
It is important that all compartments are closed tightly.  
Follow these tips carefully to prevent damage to the device.  
n
Whenever your device gets wet, dry it thoroughly with a clean, soft cloth.  
n
Do not expose the device to salt water or ionized water, or to water over 1 meter deep for more  
than 30 minutes. If your device is exposed to salt water, wash the device with fresh water then  
dry thoroughly with a clean, soft cloth. Otherwise, when it dries, salt may accumulate and block  
the microphone, earpiece, and speaker.  
n
n
When drying off your device, be sure to pat the earpiece (top front of phone), microphone  
(bottom of phone), and speaker (rear of phone) with a clean, soft cloth to remove as much water  
as possible.  
When making a call immediately after your device is wet, the microphone may have water in it  
which may lower the volume that the other person will hear. After drying off the device, allow the  
device to air-dry before making a call.  
Get Started  
2
n
n
The back and USB/Accessory Port covers may be loosened slightly if the device is dropped or  
receives an impact. Ensure that all the covers are properly aligned and tightly closed. Otherwise,  
they may not provide protection from water and dust.  
Always keep the USB/Accessory Port cover clean and be careful to avoid damaging it.  
Note: The touch screen may not be active in water.  
Charge the Battery  
1. On the bottom of the phone, gently lift the multipurpose jack cover to reveal the USB  
Charger/Accessory Port.  
2. Plug the USB cable into the Charger/Accessory Port on the bottom of the phone.  
3. Plug the other end of the USB cable into the Charging Head, and then plug the Charging Head  
into an electrical outlet to charge your battery. Fully charging a battery may take up to three  
hours.  
Note: Your phone supports USB 3.0 and USB 2.0, and includes a USB 3.0 cable for higher data  
transfer speeds when connected to another USB 3.0 device. You can also use USB 2.0 cables (not  
included) to charge and connect your phone.  
Activate Your Phone  
Follow the instructions below to activate your phone if it has not already been activated. Depending  
on your account or how and where you purchased your phone, it may be ready to use or you may  
Get Started  
3
   
need to activate it on your Sprint account.  
n
If you purchased your phone at a Sprint Store, it is probably activated and ready to use.  
n
If you received your phone in the mail and it is for a new Sprint account or a new line of service, it  
is designed to activate automatically.  
l
When you turn the phone on for the first time, you should see a Hands Free Activation  
screen, which may be followed by a PRL Update screen and a Firmware Update screen.  
Follow the onscreen instructions to continue.  
n
If you received your phone in the mail and you are activating a new phone for an existing number  
on your account (you’re swapping phones), you can activate on your computer online or directly  
on your phone.  
l
Activate on your computer:  
o
Go to sprint.com/activate and complete the online instructions to activate your phone.  
l
Activate on your phone:  
o
Turn on your new phone. (Make sure the old one is turned off.) Your phone will  
automatically attempt Hands-Free Activation.  
o
Touch Activate to override auto-activation and start the manual activation wizard.  
o
Follow the onscreen prompts to complete the activation process.  
To confirm activation, make a phone call. If your phone is still not activated, visit sprint.com/support  
for assistance. If you do not have access to the Internet, call Sprint Customer Service at 1-888-211-  
4727 from another phone.  
Note: Do not press the Power/Lock key while the phone is being activated. Pressing the  
Power/Lock key cancels the activation process.  
Complete the Setup  
After you turn on your phone and activate it, your phone displays a Welcome screen. From the  
Welcome screen follow the prompts to set up features and preferences on your phone.  
Note: In some cases, you may be able to complete the setup process before your phone has been  
activated on your Sprint account.  
1. At the Welcome screen, choose options, and then tap Start to begin setup:  
l
Language: Choose the default language for your phone’s operation.  
l
Accessibility: Configure settings to access settings to improve the accessibility of your  
phone’s features if you are visually impaired or hard of hearing.  
Get Started  
4
 
2. Follow the onscreen instructions to complete setup for each topic. Tap Next, or the right arrow,  
to move through the steps. You can skip options to continue to the next one. During setup, you  
may see these options:  
l
Wi-Fi: By default, your phone prompts you to use Wi-Fi when accessing data services. Tap a  
Wi-Fi access point to connect to it, or you can continue setup using your phone’s connection  
to the wireless network.  
l
EULA & Diagnostic Data: Read the End User License Agreement (EULA) and then tap  
the check box to confirm that you understand and agree to it terms and conditions. If you do  
not agree to the EULA, you cannot continue with setup. If you consent to provide diagnostic  
and usage data to Samsung, tap Yes, or tap No thanks.  
l
Got Google?: Your phone uses your Google account to provide access to many features  
and apps. Complete the steps to sign in to your current Google account, or sign up for a new  
Google account right from your phone. You can also skip signing in to your Google account,  
or sign in later.  
l
l
l
l
l
Google services: Select Google service preferences, including Backup & Restore,  
Location and Communication options.  
Entertainment: You can set up Google Wallet with a credit card to use with Google Wallet  
to purchase items from Google Play.  
This phone belongs to: Enter your First and Last name, to personalize Google features  
and apps.  
Samsung account: Some apps and features use your Samsung account. You can sign in  
to your Samsung account, or follow the prompts to create a new account.  
Dropbox: Dropbox provides Web-based “cloud” storage, so you can save your pictures and  
videos to the Web, and any computers you link to. If you create a Dropbox account during  
setup, you can get a 50GB Dropbox account for 2 years. You can create a new account  
here, or sign in to your existing Dropbox account.  
l
l
Device name: Your device name is how you and other devices identify your phone, such as  
when sharing via Bluetooth or Wi-Fi Direct. If you want to use a different name, tap the field  
and enter a name.  
Easy mode: Easy mode offers a simpler home screen layout, with larger text and icons. Tap  
the check box to turn on Easy mode. You can also choose Easy mode from Settings at any  
time.  
3. Tap Finish to complete setup.  
You may see a series of informational or update screens. Follow the prompts to continue.  
l
Note: During or after setup, you may see a Sprint Connections Optimizer notice. Read the notice  
and then touch I Agree to allow your phone to connect automatically to the best available data  
network, including Wi-Fi. To turn Connections Optimizer off at any time, from home touch  
>
Apps  
Get Started  
5
Settings >  
More networks > Mobile networks > Connections optimizer and uncheck  
the box. See Mobile Networks Settings for details.  
Set Up Voicemail  
Your phone automatically transfers all unanswered calls to voicemail, even if your phone is in use or  
turned off. You should set up your Sprint Voicemail and personal greeting as soon as your phone is  
activated. Always use a password to protect against unauthorized access.  
Note: Voicemail Password – Sprint strongly recommends that you create a password when  
setting up your voicemail to protect against unauthorized access. Without a password, anyone who  
has access to your phone is able to access your voicemail messages.  
1.  
From home, tap  
Phone.  
If your screen is locked, press the Power/Lock key to turn on the display and then swipe your  
screen in any direction. See Turn Your Screen On and Off.  
2.  
Touch and hold  
to dial your voicemail number.  
3. Follow the system prompts to:  
l
l
l
Create your password.  
Record your name announcement.  
Record your greeting.  
Tip: You can also access and set up voicemail with the Visual Voicemail app. From home, tap  
Apps > Voicemail, and then tap Personalize now.  
Sprint Account Information and Help  
Find out about account passwords and information about managing your account and finding help.  
Sprint Account Passwords  
As a Sprint customer, you enjoy unlimited access to your personal account information, your  
voicemail account, and your data services account. To ensure that no one else has access to your  
information, you will need to create passwords to protect your privacy.  
Get Started  
6
     
Account User Name and Password  
If you are the account owner, you will create an account user name and password when you sign on  
to sprint.com/mysprint. (Click Sign in/Sign up and then click Sign up now! to get started.) If you  
are not the account owner (if someone else receives the bill for your Sprint service), you can get a  
sub-account password at sprint.com/mysprint.  
Voicemail Password  
You’ll create your voicemail password when you set up your voicemail. See Set Up Voicemail for  
more information on your voicemail password.  
Data Services Password  
With your Sprint phone, you may elect to set up an optional data services password to control access  
and authorize Premium Service purchases.  
For more information, or to change your passwords, sign on to sprint.com/mysprint.  
Manage Your Account  
Manage your Sprint account from your computer, your Sprint phone, or any other phone.  
n
n
n
n
n
n
n
n
Access your account information.  
Check your minutes used (depending on your Sprint service plan).  
View and pay your bill.  
Enroll in Sprint online billing and automatic payment.  
Purchase accessories.  
Shop for the latest Sprint phones.  
View available Sprint service plans and options.  
Learn more about data services and other products like games, ring tones, screen savers, and  
more.  
From Your Sprint Phone  
1.  
From home, tap  
Phone.  
2. Do any of the following:  
l
Tap  
to access a summary of your Sprint service plan or to get  
answers to other questions.  
Get Started  
7
     
l
l
Tap  
Tap  
to make a payment.  
to check minute usage and account balance.  
Note: For additional account information, you can access Sprint Zone from your device. From  
home, tap Apps > Sprint Zone.  
Sprint Support Services  
Sprint 411 and Sprint Operator Services let you easily access information and calling assistance  
from your Sprint phone.  
Sprint 411  
Sprint 411 gives you access to a variety of services and information, including residential, business,  
and government listings; movie listings or show times; driving directions, restaurant reservations,  
and major local event information. You can get up to three pieces of information per call, and the  
operator can automatically connect your call at no additional charge.  
There is a per-call charge to use Sprint 411, and you will be billed for airtime.  
1.  
2.  
From home, tap  
Tap  
Phone.  
.
Sprint Operator Services  
Sprint Operator Services provides assistance when you place collect calls or when you place calls  
billed to a local telephone calling card or third party.  
1.  
2.  
From home, tap  
Tap  
Phone  
.
Note: For more information or to see the latest in products and services, visit us online at  
Get Started  
8
     
Phone Basics  
Your phone is packed with features that simplify your life and expand your ability to stay connected to  
the people and information that are important to you. The following topics will introduce the basic  
functions and features of your phone.  
Your Phone’s Layout  
This illustration outlines your phone’s basic layout.  
See Features for more information.  
Features  
The following list defines the features listed in the above illustrations.  
n
LED indicator: Glows or blinks in different colors to show status when the screen is turned off.  
The LED glows red when charging, and blinks red when the battery is low; blinks blue when  
there’s a new notification, or when you are recording voice with the screen turned off; and glows  
green when the battery is fully charged and the phone is attached to a charger.  
n
n
Earpiece: Lets you hear the caller and automated prompts during calls.  
Proximity Sensor: Detects the presence of objects near the phone, such as when using air  
gesture or motion settings. For example, while talking on the phone the sensor detects when it’s  
near your ear and turns off the screen to prevent accidental key presses.  
Phone Basics  
9
         
n
Light Sensor: Detects the ambient light level, such as when setting screen brightness when  
Automatic brightness is enabled, and when using the Camera.  
n
n
Front Camera: Allows you to take pictures and videos of yourself.  
Power/Lock key: Lets you turn the phone on or off, turn the screen on or off, or lock the screen.  
Press and hold for a Device options menu, where you can turn the phone off or restart it, or for  
easy access to Airplane mode, Emergency Mode, and to Mute, Vibrate, and Sound modes.  
n
Back key: Lets you return to the previous screen, or close a dialog box, options menu, the  
Notification panel, or onscreen keyboard.  
n
n
Home Key: Returns you to the Home screen.  
Recent Apps: Displays a list of apps you’ve used recently. Press and hold to configure the  
home screen.  
n
Volume key: Adjusts the volume of your phone’s sounds. From the home screen, press to adjust  
master volume. During calls or playback, press to adjust volume. Press to mute the ringtone of  
an incoming call.  
n
n
3.5 mm Headset Jack: Allows you to plug in either a stereo headset or an optional headset for  
convenient, hands-free conversations.  
Microphones: Allow other callers to hear you when you are using the speakerphone, and  
captures sound during recording.  
n
n
Infrared transmitter: Allows you to control other devices, such as a TV.  
Heart rate sensor: Measures your heart rate when you hold your finger over the sensor, for use  
®
with apps like S Health .  
n
n
n
n
USB Charger/Accessory Port: Aallows you to connect the phone charger/USB cable  
(included) and other optional accessories (not included).  
Speaker: Plays ringtones and sounds. The speaker also lets you hear the caller’s voice in  
speakerphone mode.  
Flash: Helps illuminate subjects in low-light environments when the camera is focusing and  
capturing a photo or video.  
Camera: Lets you take pictures and record videos.  
Note: Your phone supports USB 3.0 and USB 2.0, and includes a USB 3.0 cable for higher data  
transfer speeds when connected to another USB 3.0 device. You can also use USB 2.0 cables (not  
included) to charge and connect your phone.  
CAUTION: Inserting an accessory into the incorrect jack may damage the phone.  
Phone Basics  
10  
                 
Turn Your Phone On and Off  
Use the Power/Lock key to turn the phone on or off.  
Turn the Phone On  
n
Press and hold the Power/Lock key.  
Turn the Phone Off  
1. Press and hold the Power/Lock key to display the device options menu.  
2. Tap Power off > OK to turn the phone off.  
The screen remains blank while your phone is off. If the phone is off during charging, the screen  
displays a charging animation.  
Turn Your Screen On and Off  
Your phone allows you to quickly turn the screen off when not in use and to turn it back on and unlock  
it when you need it.  
Turn the Screen Off When Not in Use  
n
To quickly turn the screen off, press the Power/Lock key. Pressing the Power/Lock key again  
will turn on the screen and display the lock screen.  
To save battery power, the phone automatically turns off the screen (times out) after a certain period  
of time when you leave it idle. You will still be able to receive messages and calls while the phone’s  
screen is off.  
Note: For information on how to adjust the time before the screen turns off, see Screen Timeout.  
Turn the Screen On and Unlock It  
1. To turn the screen on, press the Power/Lock key.  
2. Unlock the screen:  
l
If you are using the default screen lock, swipe the screen in any direction to unlock it.  
If you have set up a screen lock, use your screen lock. See Screen Lock.  
l
Features  
Your phone offers new features for using gestures to interact with your phone.  
Phone Basics  
11  
         
Motions and Gestures  
Control your phone by making specific gestures with your hand above the phone’s screen.  
n
n
n
n
Air browse: When on, you can scroll through pages, or move to the previous or next item, by  
moving your hand up and down, or left and right, over the screen.  
Direct call: When on, you can call the contact whose recent call log, message, or contact details  
are displayed by lifting the phone to your ear.  
Smart alert: When on, your phone will vibrate to alert you to missed calls and notifications that  
occurred since the last time you picked up your phone.  
Mute/pause: When on, you can mute incoming calls and pause playback by turning the phone  
screen-side down, or by covering the screen with your hand. You can also use Smart pause, to  
have the phone pause video playback when you look away from the screen.  
n
Capture screen: When on, you can create a copy of the current screen by swiping the side of  
your hand across the screen, from left to right or right to left. The screen shot is saved to the  
clipboard, and to the Screenshots folder.  
Enable Motions and Gestures  
n
From home, tap  
Apps >  
Settings >  
Motions and gestures.  
Air View  
Air View allows you to hover your finger over items on the screen to display more information.  
n
Information preview: Hover over items to display information previews, extended text, or  
enlarged images, depending on the type of item. For example, you can hover your finger over an  
event in Calendar to see event details, or hover over an album in Gallery to view the pictures in  
the album. You can also hover your finger over a progress bar when playing a video, to preview  
a scene and see elapsed time.  
n
Webpage magnifier: Hover over a webpage to magnify the content under your finger.  
Configure Air View  
Enable Air View features, and learn about using them.  
n
From home, tap  
Apps >  
Settings >  
Air View.  
Phone Basics  
12  
   
Multi Window  
Multi Window allows you to use two apps on the same screen, in separate, resizable windows.  
Turn Multi Window On or Off  
Turn Multi window on or off in Settings.  
1.  
From home, tap  
Apps >  
Settings >  
Multi window.  
2. Tap the ON/OFF switch beside Multi window to enable or disable the option.  
Display Multi Window  
After you turn Multi window on in Settings, you can control whether the Multi window tray displays on  
the screen, for easy access to its features.  
By default, the Multi window tray tab displays on the left side of the screen. You can drag the tab  
along the side of the screen, or tap the tab to open Multi Window, and then drag Multi window to the  
right side of the screen, or the bottom.  
n
To display the Multi window tab, touch and hold  
Back.  
Work with Multi Window  
After enabling Multi Window, you can use it to run two apps at the same time. You can launch apps  
from Multi window, or drag an app to the screen to run multiple apps at the same time.  
The apps display together on a split screen. You can switch between the apps, adjust the size of  
their display on the screen, and copy information from one app to the other.  
1. Tap the Multi window tab to display the tray, and then drag apps to the windows.  
2. You can also use these Multi window options:  
l
Adjust the Size of Apps in Multi Window: Drag the border between the windows to a  
new position.  
Phone Basics  
13  
 
l
Tap the circle at the center of the border between the windows to display the Multi window  
toolbar:  
l
l
Switch window positions: Switches the position of the app windows on the screen.  
Drag text or a screenshot: Enables drag and drop. In selected apps, you can you can  
touch text in a window, or tap the window, and then drag to copy content to the app in the  
other window.  
l
Close a window: Closes the active window. The active window is the window you touched  
last.  
Touchscreen Navigation  
Your phone’s touchscreen lets you control actions through a variety of touch gestures.  
Tap  
When you want to type using the onscreen keyboard, select items onscreen such as application and  
settings icons, or other items, simply tap them with your finger.  
Touch and Hold  
To open the available options for an item (for example, a contact or link in a Web page), touch and  
hold the item.  
Phone Basics  
14  
     
Swipe or Slide  
To swipe or slide means to quickly drag your finger vertically or horizontally across the screen.  
Drag  
To drag, touch and hold your finger with some pressure before you start to move your finger. While  
dragging, do not release your finger until you have reached the target position.  
Phone Basics  
15  
   
Flick  
Flicking the screen is similar to swiping, except that you need to swipe your finger in light, quick  
strokes. This finger gesture is always in a vertical direction, such as when flicking the contacts or  
message list.  
Rotate  
For most screens, you can automatically change the screen orientation from portrait to landscape by  
turning the phone sideways. When entering text, you can turn the phone sideways to bring up a  
bigger keyboard.  
Phone Basics  
16  
   
Note: You can control screen rotation with the Screen rotation setting. To make this selection, from  
home tap Apps > Settings > Display > Screen rotation. See Screen Rotation for  
more information.  
Pinch and Spread  
“Pinch” the screen using your thumb and forefinger to zoom out or “spread” the screen to zoom in  
when viewing a picture or a Web page. (Move fingers inward to zoom out and outward to zoom in.)  
Phone Basics  
17  
   
Tip: Pinching any home screen will show you options to customize home screens, or tap a thumbnail  
to go straight to another screen.  
Your Home Screen  
The home screen is the starting point for your phone’s applications, functions, and menus. You can  
customize your home screen by adding application icons, shortcuts, folders, widgets, and more. The  
home screen extends beyond the initial screen. Swipe the screen left or right to display additional  
screens.  
Note: You can keep swiping in one direction to move through all the home screens. The indicator  
near the bottom of the screen shows your current screen position.  
Tip: Press  
Home to return to the main home screen from any other screen.  
Customize Your Home Screen  
You can customize your home screen by adding shortcuts, shortcuts, folders, widgets, and more.  
Create a Shortcut  
Use shortcuts to launch an app from the home screen.  
1.  
From home, tap  
Apps.  
2. Touch and hold an app icon, and then drag it to a home screen and release it.  
Move a Shortcut  
Move a shortcut to another home screen.  
1. From home, touch and hold a shortcut to undock it.  
2. Drag the icon to a different location, and then release it.  
Phone Basics  
18  
     
Remove a Shortcut  
Remove a shortcut from the home screen.  
1. From home, touch and hold a shortcut to undock it.  
2. Drag the icon to the Remove icon and then release it.  
Note: Removing a shortcut does not delete the app, it just removes the shortcut from the home  
screen.  
Remove a Primary Shortcut  
Primary shortcuts are the Phone, Contacts, Messages, Internet, and Apps shortcuts that appear at  
the bottom of the home screen by default. You can remove or replace any of your primary shortcuts,  
except the Apps shortcut.  
1. From home, touch and hold a shortcut to undock it.  
2. Drag it to another screen, or to the Remove icon.  
Create a Primary Shortcut  
Primary shortcuts appear at the bottom of the home screen by default. You can remove or replace  
any of the primary shortcuts, except the Apps shortcut.  
1. From home, touch and hold a shortcut to undock it.  
– or –  
Tap  
Apps, and then touch and hold an app icon.  
2. Drag the shortcut to a new position in the primary shortcuts.  
Note: If there are already five primary shortcuts, the new shortcut will replace one of the existing  
shortcuts.  
Add a Widget  
Widgets are self-contained apps that display on a home screen. Unlike a shortcut, the Widget works  
like as an onscreen application. There are all kinds of widgets, including links to a specific contact,  
®
Internet bookmarks, Facebook status windows, Gmail and email accounts, and many others.  
1. From home, pinch the screen.  
– or –  
Touch and hold an empty space on the screen.  
2. Tap Widgets, and then scroll to find one.  
3. Touch and hold the widget, and then drag it to a home screen and release it  
Phone Basics  
19  
Remove a Widget  
1. From home, touch and hold on a widget to undock it.  
2. Drag the widget to the Remove icon and release it.  
Note: Removing a widget does not delete the widget, it just removes the widget from the home  
screen.  
Choose Wallpapers  
Change the look of the home and lock screens with wallpaper. You can display a favorite picture, or  
choose from preloaded wallpapers.  
1. From home, pinch the screen.  
– or –  
Touch and hold an empty space on the screen.  
2. Tap Wallpapers, and then choose Home screen, Lock screen, or Home and lock screens.  
3. Tap a wallpaper to see a sample, and then tap Set wallpaper. If you choose an image from  
Gallery or Dropbox, you can adjust the crop box to decide what’s displayed, and then touch  
Done to set it as the wallpaper.  
Configure Home Screen Settings  
Choose options for the home screen.  
1. From home, pinch the screen.  
– or –  
Touch and hold an empty space on the screen.  
2. Tap Home screen settings, and then enable or disable these options:  
l
l
Transition effect: When enabled, a page-turning effect displays as you scroll through the  
home screens.  
My Magazine: When enabled, My Magazine displays on the far-left home screen. For more  
information, see My Magazine.  
Extended Home Screens  
In addition to the main home screen, your phone has up to six extended home screens to provide  
more space for adding shortcuts, widgets, and more.  
Note: You can have up to seven screens, including the main home screen.  
Phone Basics  
20  
 
Add a Home Screen  
You can have up to seven home screens.  
1. From home, pinch the screen.  
– or –  
Touch and hold an empty space on the screen.  
2.  
Scroll to the last screen, and then tap  
to add a screen.  
Delete a Home Screen  
You can delete home screens, except for the default three screens.  
1. From home, pinch the screen.  
– or –  
Touch and hold an empty space on the screen.  
2. Scroll to the screen you want to delete, and then touch and hold it and drag it to the Remove icon  
at the top of the screen.  
Status Bar and Notification Panel  
The status bar at the top of the home screen provides phone and service status information on the  
right side and notification alerts on the left. To view notifications, open the Notification panel by  
touching and holding the Status bar and dragging it down.  
Status Bar  
The status bar displays icons to notify you of your phone’s status, as well as notifications.  
Status Icons  
Icon  
Description  
®
Bluetooth is on  
Bluetooth is on, and your phone is connected to another device  
®
Wi-Fi is on  
Phone Basics  
21  
     
Icon  
Description  
Wi-Fi networks available  
Vibrate  
Mute  
Speakerphone Active  
3G Data Service  
3G Data Service, in use. The rays spin when data is being transferred.  
Sprint Spark Enhanced LTE data service The rays spin when data is being  
transferred.  
Signal strength. More bars indicate a stronger signal.  
Roaming signal strength. More bars indicate a stronger signal.  
Airplane Mode  
Battery is charging  
Battery is fully charged  
Notification Icons  
Icon  
Description  
Missed call  
New email  
New Gmail  
New message  
New voicemail  
New Hangouts message  
New Sprint Zone message  
Event  
USB 2.0 or lower connection  
Phone Basics  
22  
 
Icon  
Description  
USB 3.0 connection  
App update(s) available  
App update(s) successful  
Downloading  
Keyboard active (choose input method)  
Screen lock setup needed  
Attention needed: System error or alert  
More notifications available: See notification panel  
Determining location.  
Notification Panel  
The Notification panel displays details about your phone’s status, and it provides easy access to  
common settings and features.  
Use the Notification Panel  
1. Open the Notification panel by touching and holding the Status bar and dragging it down.  
2. On the Notification panel, you have these options:  
l
Quick Settings: Quickly access popular settings. Tap a setting to turn the option on or off, or  
touch and hold to display its settings.You can swipe your finger across the quick settings, to  
see all available settings.  
l
l
S Finder: Search for content on your device, and find more on the Web. You can apply  
filters to your results, and view your search history.  
Quick connect: Search for nearby devices, to share information  
Quick Settings  
Use Quick settings from the Notification panel to control popular settings.  
1. From home, swipe your finger down from the Status bar at the top of the screen to display the  
Notification panel.  
Phone Basics  
23  
 
2. Tap a setting to turn the option on or off, or touch and hold on a setting to display its settings. You  
can swipe your finger across the quick settings, to see all available settings. You also have these  
options:  
l
Tap  
to display more quick settings.  
l
Choose which settings display on the Notification panel. Tap  
at the top of the Notification  
panel, and then tap  
Edit for options:  
o
Brightness adjustment: When enabled, a Brightness option displays on the  
Notification panel, so you can make adjustments to the screen brightness.  
o
o
Recommended apps: When on, your phone will display a selection of app icons on the  
Notification panel, according to your actions. For example, when you connect a headset,  
Music and other entertainment apps will display. Tap the ON/OFF switch to turn the  
option on, and then tap Edit to choose apps to display.  
Set quick setting buttons: You can customize which quick settings display on the  
Notification panel, and change the order they appear. To replace settings, touch and  
hold on a button, and drag it to a new position. You can drag buttons from the Available  
buttons area of the screen to a position in the Notification panel area, or from the  
Notification panel area to the Available buttons.  
l
Tap  
Settings to access the full Settings menu.  
Enter Text  
You can type on your device using the available touchscreen QWERTY keyboard, or by speaking  
your inputs.  
Text Input Methods  
Your device offers several text input methods.  
n
n
n
Samsung keyboard allows you to enter text by touching keys on a virtual QWERTY keyboard.  
Samsung keyboard includes optional predictive text, which matches your key touches to  
common words so you can select a word to insert it into your text.  
Swype™ lets you enter words by swiping across the virtual QWERTY keyboard. Instead of  
tapping each key, use your finger to trace over each letter of a word. You can also tap letters to  
enter words.  
Google voice typing allows you to speak your entries.  
Phone Basics  
24  
     
Select a Default Text Input Method  
You can select a default Text Input Method from Settings, or choose on at any time while entering  
text.  
From Settings:  
n
From home, tap  
Apps >  
Settings >  
Language and input > Default, and then  
choose a default entry method.  
While entering text:  
1. From a screen where you can enter text, drag down from the top of the screen to open the  
Notification panel.  
2. Tap Choose input method, and then choose a text entry method.  
Google Voice Typing  
This feature uses Google voice recognition to convert your spoken words into text.  
Use Google Voice Typing to Enter Text  
1. From a screen where you can enter text, drag down from the top of the screen to open the  
Notification panel, and then tap Choose input method > Google voice typing.  
– or –  
Tap  
or  
from the onscreen keyboard.  
2. Speak into the microphone and watch your text being entered onscreen.  
3. If the text is incorrect, tap DELETE.  
4. Once you have completed entering your text, tap Done. The onscreen keyboard will reappear.  
Note: Select a language from the menu at the top of the Listening area. Tap Add more  
languages to assign a new language via the Google voice typing menu. Removing the check mark  
from the Automatic field allows you to select additional languages.  
Configure Google Voice Typing  
n
From home, tap  
Apps >  
Settings >  
Language and input, and then tap  
beside Google voice typing.  
Phone Basics  
25  
     
Samsung Keyboard  
With Samsung Keyboard, it's easy to enter text, symbols, and numbers.  
Use Samsung Keyboard to Enter Text  
1. From a screen where you can enter text drag down from the top of the screen to open the  
Notification panel, and then tap Choose input method > Samsung keyboard.  
2. Tap keys to enter text. While entering text, use these options:  
l
If you make a mistake, tap  
whole word or field.  
to delete incorrect characters. Touch and hold  
to delete a  
l
l
Tap  
to change the case of the text (the arrow will turn blue). Tap  
twice to switch to  
all capitals (the key will turn blue).  
Tap  
to switch to a symbols keyboard, to enter symbols. There are two symbol  
keyboards.  
l
l
Tap  
If you have more than one language selected in Samsung Keyboard settings, you can swipe  
your finger over to switch between languages.  
to switch to Google Voice typing to enter text by speaking.  
Configure Samsung Keyboard  
n
From home, tap  
Apps >  
Settings >  
Language and input, and then tap  
beside Samsung keyboard.  
Note: For more information about Samsung Keyboard settings, see Samsung Keyboard Settings.  
Swype  
Swype lets you enter words by tracing over the letters on the virtual QWERTY keyboard. Instead of  
tapping each key, use your finger to trace over each letter of a word. You can also tap letters to enter  
words.  
Swype provides next-letter prediction and regional error correction, which can compensate for  
tapping the wrong keys on the virtual QWERTY keyboards.  
Phone Basics  
26  
   
Use Swype to Enter Text  
1. From a screen where you can enter text drag down from the top of the screen to open the  
Notification panel, and then tap Choose input method > Swype.  
2. Swipe your finger continuously over the letters to form a word. As you swipe over letters, words  
matching your pattern display at the top of the Swype keyboard. To enter a word, lift your finger,  
or tap a word at the top of the keyboard.  
3. While entering text, use these options:  
l
If you make a mistake, tap  
to delete a single character. Touch and hold  
to  
delete an entire word or field.  
l
By default, Swype starts with a capital at the beginning of text. Tap  
capital letter, or tap twice to enter all capitals.  
to start with a  
l
Tap  
to switch to a symbols keyboard, and then tap keys to enter symbols.  
Configure Swype  
n
From home, tap  
Apps >  
Settings >  
Language and input, and then tap  
beside Swype.  
– or –  
From the Swype keyboard, touch and hold  
.
Note: For more information about Swype settings, see Swype Settings.  
Tips for Editing Text  
These tips allow you to cut or copy selected text and paste it into a separate selected area.  
1. In a text entry field, double-tap the text, and then drag the sliders to select the text.  
2. Tap an onscreen option from the Edit text toolbar. You can drag your finger along the toolbar to  
see all the options:  
l
Select all: Highlights all the text in the field.  
l
Cut: Removes the selected text and saves it to the clipboard.  
l
Copy: Copies the selected text to the clipboard.  
Phone Basics  
27  
 
l
l
l
Paste: Insert the last copied or cut text into the current field.  
Clipboard: Display the clipboard to choose previously cut or copied text.  
Dictionary: Access your personal dictionary.  
Phone Basics  
28  
Phone Calls  
With the Sprint National Network and your phone, you can enjoy clear calling across the country.  
Make Phone Calls  
There are several convenient ways to place calls from your phone.  
Call Using the Keypad  
The most “traditional” way to place a call is by using the phone’s keypad screen.  
1.  
From home, tap  
Phone.  
2. Tap the number keys to enter the phone number.  
l
As you enter digits, matching numbers from recent calls or contacts display. If you see the  
number you want, tap it to call it without having to enter the rest of the number.  
3.  
Tap  
to call the number.  
Call from Logs  
All incoming and outgoing calls are recorded in Logs. You can call a number from a recent call from  
Logs.  
1.  
2.  
From home, tap  
Phone > Logs.  
to call the number.  
Tap a call record, and then tap  
Tip: You can also swipe across a recent call from left to right to call the number, or from right to left to  
send a message.  
Call from Contacts  
You can place calls directly from Contacts.  
Note: You can access Contacts directly from the Phone app. Tap  
Phone > Contacts tab at the  
top of the screen.  
Phone Calls  
29  
         
1.  
2.  
From home, tap  
Contacts.  
Tap a contact, and then tap  
– or –  
.
Touch the contact’s picture icon, and then tap  
– or –  
.
Swipe your finger across the contact from left to right.  
Call a Number in a Text Message  
While viewing a text message, you can place a call to a number that is in the body of the message.  
For more information, see Text and Multimedia Messaging.  
1.  
From home, tap  
Messages.  
2. Open the message with the phone number and then tap the phone number.  
3. Tap Call to dial the number.  
Call a Number in an Email Message  
While viewing an email or Gmail™ message, you can place a call to a number that is in the body of  
the message.  
1.  
From home, tap  
Apps >  
Email or  
Gmail.  
2. Open the message with the phone number and then tap the phone number.  
3. The Phone screen opens, with the phone number automatically entered and ready to be dialed.  
To place the call, tap  
.
Make an Emergency Call  
You can place calls to 9-1-1 even if the phone’s screen is locked or your account is restricted.  
Note: To call the 9-1-1 emergency number when the phone’s screen is locked, press the  
Power/Lock key to turn the screen on, and then touch Emergency call on the lock screen.  
Phone Calls  
30  
     
1.  
2.  
From home, tap  
Tap  
Phone.  
.
Enhanced 9-1-1 (E 9-1-1) Information  
This phone features GPS (Global Positioning System), which is used for E 9-1-1 emergency location  
service, where available.  
When you place a call to 9-1-1, the GPS feature of your phone provides information about your  
approximate location. Depending on several variables, including availability and access to satellite  
signals, it may take up to 30 seconds or more to determine and report your approximate location.  
Important: Always report your location to the 9-1-1 operator when placing an emergency call.  
Some designated emergency call takers, known as Public Safety Answering Points (PSAPs), may  
not be equipped to receive GPS location information from your phone.  
Receive Phone Calls  
When you receive a call, you can accept the call, or reject the call to send it to voicemail. You can  
also reject a call with a message, to send a text message to the caller.  
Note: If your phone is turned off, all calls automatically go to voicemail.  
Answer an Incoming Call  
When you receive a phone call from a number stored in Contacts, the contact’s information displays  
on the screen. When you receive a phone call from a number that is not stored in Contacts, the  
phone number displays on the screen.  
n
When your phone notifies you of an incoming call, drag  
to the right to answer the call.  
Mute the Ringing Sound  
You can mute the ringtone without rejecting the call by doing one of the following.  
n
Press the Volume key down.  
n
Place the phone screen-down on a level surface. See Motions and Gestures Settings for  
options, including the Mute/pause Motion to mute incoming calls by turning over the phone.  
n
Cover the screen with your hand. See Motions and Gestures Settings for options, including the  
Mute/pause motion to mute incoming calls by covering the screen with your hand.  
Reject an Incoming Call  
When you reject a call, the caller is sent to voicemail, where they can leave a voice message.  
Phone Calls  
31  
   
n
When your phone notifies you of an incoming call, drag  
to the left to reject the call.  
Reject an Incoming Call with a Text Message  
You can reject an incoming call by sending a text message to the caller.  
1.  
When your phone notifies you of an incoming call, drag  
toward the top of the screen.  
2. Select an existing message.  
– or –  
Tap  
Phone Call Options  
The Phone app provides many useful features and options to help you make the most of your calling  
experience.  
Dialing Options  
1.  
From home, tap  
Phone.  
2.  
While dialing a call, tap  
More for options, including:  
l
l
l
Add 2-sec pause: Insert a 2-second pause into the number you are dialing. This can be  
useful when storing numbers for automated phone menus.  
Add wait: Insert a pause into the number you are dialing, to wait for input from you. This can  
be useful when storing numbers for automated phone menus.  
Add to Contacts: Save the number to a new contact, or update an existing contact. See  
Add a Contact for more information.  
l
l
l
l
Send message: Send a text message to the number you dialed.  
Speed dial: View speed dials. For more information, see Speed Dials.  
Settings: Configure call settings. For more information, see Call Settings.  
Help: Learn about using the Phone app.  
Caller ID  
Caller ID identifies a caller while the phone is ringing, by displaying the number of the incoming call.  
Phone Calls  
32  
     
Block Caller ID  
You can block your Caller ID (visible to other when you make a call), before making a call. The  
blocking only lasts for that call, and then returns to regular Caller ID.  
To permanently block your number, you must call Sprint Customer Service.  
1.  
2.  
3.  
From home, tap  
Tap  
Phone.  
.
Enter a phone number, and then tap  
.
Call Waiting  
When you’re on a call, your phone notifies you by displaying the call information on the screen, and  
vibrating, if you’ve set up vibration for incoming calls.  
Respond to an Incoming Call While You’re On a Call  
n
Slide  
to the right. This puts the first caller on hold and answers the incoming call.  
l
To switch between calls, tap Swap.  
3-way Calling  
With 3-Way Calling, you can talk to two people at the same time. When using this feature, the normal  
airtime rates will be charged for each of the two calls.  
1.  
2.  
From home, tap  
Phone.  
Make the first call by entering the phone number and pressing  
.
3. When the first call is established, tap Add call to put the first call on hold, and then dial the  
second number.  
4. When the second call is established, tap Merge.  
l
l
If one of the people you called hangs up during your call, you and the remaining caller stay  
connected.  
If you set up the call and are the first to end the call, all callers are disconnected.  
Phone Calls  
33  
   
Call Forwarding  
Call Forwarding lets you forward all your incoming calls to another phone number – even when your  
phone is turned off. You can continue to make calls from your phone when you have Call Forwarding  
is activated.  
Note: You are charged a higher rate for forwarded calls.  
Activate Call Forwarding  
1.  
2.  
From home, tap  
Phone.  
, and then enter the phone number to which you want your calls  
Tap  
forwarded.  
3.  
Tap  
. A tone confirms the activation of Call Forwarding.  
Deactivate Call Forwarding  
1.  
2.  
3.  
From home, tap  
Tap  
Phone.  
.
Tap  
. A tone plays to confirm the deactivation of Call Forwarding.  
In-call Options  
While you’re on a call, you can use options to find information or multitask during the call.  
Phone Calls  
34  
   
n
n
Add call: Display the Keypad to dial another call.  
Keypad: Display the Keypad, where you can enter numbers to use DTMF (Dual Tone Multi-  
Frequency). This can be useful if you need to enter an access code or other information while on  
a call.  
n
n
End call: Hang up the call.  
Speaker: Control whether call audio plays through the speaker or the earpiece.  
Warning: Because of higher volume levels, do not place the phone near your ear while using the  
speaker.  
n
Mute: Control whether the other party can hear your side of the call.  
n
Bluetooth: Connect to a Bluetooth device, or disconnect from a device.  
n
Tap  
Menu for more options:  
l
l
l
l
Contacts: Launch Contacts.  
Memo: Launch Memo, to create memo during a call.  
Messages: Launch Messages, to create a new message.  
Personalize call sound: Adjust sounds on the call to your preferences.  
o
Adapt sound: Tap Start, and then follow the onscreen prompts to find the best sound  
for you.  
o
Soft sound: Use softer sounds during calls.  
o
Clear sound: Use clearer sounds during calls.  
o
Off: Use the default call sound settings.  
l
l
Extra volume: Tap to enable or disable extra volume. When enabled, your phone boosts  
the volume during calls.  
Settings: Launch Call Settings. For more information, see Call Settings.  
Voicemail  
The following topics outline your phone’s voicemail service.  
Note: Your phone also supports the Visual Voicemail app. For information on setting up and using  
Visual Voicemail, see Visual Voicemail.  
Phone Calls  
35  
 
Voicemail Setup  
You should set up your voicemail and personal greeting as soon as your phone is activated.  
n
n
To set up voicemail using your phone’s traditional voicemail, see Set Up Voicemail.  
For information on using the Visual Voicemail app, see Visual Voicemail.  
Retrieve Your Voicemail Messages  
You can review your messages directly from your phone (using either traditional voicemail or Visual  
Voicemail), or from any other touch-tone phone.  
Use Traditional Voicemail to Access Your Messages  
1.  
2.  
From home, tap  
Touch and hold  
Phone.  
.
3. Follow the system prompts to enter your voicemail password and manage voicemail.  
Use Visual Voicemail to Access Your Messages  
1.  
From home, tap  
Apps >  
Voicemail  
2. Touch an entry to listen to the message.  
Note: You are charged for airtime minutes when you access voicemail from your wireless phone.  
Use Another Phone to Access Messages  
1. Dial your wireless phone number.  
2. When your voicemail answers, press the asterisk key on the phone (*).  
3. Enter your password.  
Voicemail Notification  
There are several ways your phone alerts you to a new message.  
n
By sounding the notification ringtone.  
By displaying in the Notifications area of the Status bar when there’s a new voicemail  
n
Phone Calls  
36  
     
message.  
n
By displaying the number of new voicemail message(s) on the Voicemail app icon.  
Note: When you are roaming off the network, you may not receive notification of new voicemail  
messages. It is recommended that you periodically check your voicemail by dialing 1 + area code +  
your wireless phone number. When your voicemail answers, touch  
and enter your password.  
Roaming rates apply when you access voicemail while roaming off the network.  
Note: Your phone accepts messages even when it is turned off. However, your phone notifies you  
of new messages only when it is turned on and you are in a network service area.  
Visual Voicemail  
Visual Voicemail gives you a quick and easy way to access your voicemail. Now you can find exactly  
the message you are looking for without having to listen to every voicemail message first. This new  
feature periodically goes out to your voicemail, and gathers the caller information from all of the  
current voicemails. It then populates a list with the caller name and number, along with the length of  
time and priority level of the voicemail message.  
1.  
From home, tap  
Apps >  
Voicemail.  
2. Follow the prompts to set up an account and learn about using Visual Voicemail.  
Note: You can also access Visual Voicemail from the  
Phone keypad by tapping  
.
Set Up Visual Voicemail  
Setting up Visual Voicemail follows many of the same procedures as setting up traditional voicemail.  
You should set up your voicemail and personal greeting as soon as your phone is activated. Your  
phone automatically transfers all unanswered calls to your voicemail, even if your phone is in use or  
turned off.  
Note: To set up your traditional voicemail, see Set Up Voicemail.  
1.  
From home, tap  
Apps >  
Voicemail.  
2. Touch Personalize now and follow the system prompts to:  
l
l
l
Create a password (part of standard voicemail).  
Record your name announcement.  
Record your greeting.  
Phone Calls  
37  
     
Review Visual Voicemail  
Visual Voicemail lets you easily access and select which messages you want to review.  
1.  
From home, tap  
2. Touch a message to review it.  
Tip: There are icons at the bottom of the review screen for maintenance, storage, messaging, and  
Apps >  
Voicemail.  
other options. For an explanation of all your options, touch  
> Help.  
Listen to Multiple Voicemail Messages  
When you are done listening to a voicemail message you can easily access other voicemail  
messages without returning to the main voicemail screen.  
You can navigate through voicemail messages as frequently as you'd like. You can even move to the  
next or previous message before you're finished listening to the current one.  
1. Listen to the current voicemail message.  
2. Swipe your finger left or right to display the next or previous message. (It will begin playing  
automatically.)  
Use Visual Voicemail to Delete Your Messages  
1.  
2.  
From home, tap  
Apps >  
Voicemail  
Open a message and touch  
Delete.  
Tip: You can restore messages you have sent to the trash folder. Touch Inbox > Trash, touch and  
hold the message you want to restore to the inbox, and then touch the restore icon.  
Visual Voicemail Options  
Your visual voicemail options appear as icons at the bottom of the voicemail review screen.  
1.  
From home, tap  
Apps >  
Voicemail.  
2. Touch a message to review it. The following options are available while reviewing a voicemail  
message:  
Note: Not all options are available for all messages.  
l
Call: Return the call.  
Phone Calls  
38  
     
l
Share: Send the message via Wi-Fi Direct, Bluetooth share, Dropbox, Scrapbook,  
Messages, Gmail, Email, Voicemail, S Note, Hangouts, Google+, or Flipboard.  
l
l
Delete: Erase the selected message(s) from your Visual Voicemail.  
Reply: Respond to the message via text or voice message.  
Configure Visual Voicemail Settings  
The Visual Voicemail settings menu lets you access settings for notifications, pictures, greetings,  
and more.  
1.  
2.  
From home, tap  
Apps >  
Voicemail.  
Touch > Settings. Select an option to change its settings.  
Note: Voicemail settings can also be accessed in Settings. From home, tap  
Settings > Call > Voicemail settings.  
Apps >  
Change Your Main Greeting  
Your main greeting can be changed directly via the Visual Voicemail system. This direct access  
saves you from having to navigate within the voicemail menu.  
1.  
2.  
From home, tap  
Apps >  
Voicemail.  
Touch > Settings > Personalize voicemail.  
3. Touch OK to connect to the voicemail system. Follow the prompts to change your current  
greeting.  
Edit the Display Name  
From your Visual Voicemail menu, you can quickly change the name or number attached to your  
voice messages. This name or number identifies you to recipients of your voicemail messages.  
1.  
2.  
From home, tap  
Apps >  
Voicemail.  
Touch > Settings > Display name.  
Phone Calls  
39  
     
3. Touch the existing identification field and enter a new identifying name or number (used to  
identify you to recipients of your voice messages).  
4. Touch OK to save your information.  
Logs  
The Logs tab of the Phone app lists all missed, dialed, received, and rejected calls.  
View Logs  
From Logs, you manage the list of recent calls.  
1.  
From home, tap  
Phone > Logs.  
2. While viewing the list of calls, you can use these options:  
l
Tap the menu to display All calls, Missed calls, Dialed calls, Received calls, or  
Rejected calls.  
l
l
Tap a call to display the call record, where you can tap  
message to the caller.  
to return the call, or  
to send a  
Touch and hold on a call record to select it. You can continue selecting calls to  
Make a Call from Logs  
You can return a call from a recent call record.  
1.  
2.  
From home, tap  
Phone > Logs.  
to call the number.  
Tap a call record, and then tap  
Tip: You can also swipe across a call record from left to right to call the number.  
Send a Message from Logs  
You can send a message to a number from a recent call record.  
1.  
2.  
From home, tap  
Phone > Logs.  
to create a message to the number.  
Tap a call record, and then tap  
Tip: You can also swipe across a call record from right to left to create a message.  
Phone Calls  
40  
 
Save a Number to Contacts from Logs  
You can save a number from a recent call record to create a new contact, or update an existing  
contact.  
1.  
2.  
From home, tap  
Phone > Logs.  
> Create contact or Update existing.  
Tap a call record, and then tap  
Search Logs  
Enter criteria to search for call records. You can enter numbers to find a phone number, or letters to  
find a contact name or caller ID.  
1.  
2.  
From home, tap  
Phone > Logs.  
Tap Menu > Search.  
3. Enter criteria to display matching call records.  
Send a Number from Logs  
You can send a number from a call record in a text message.  
1.  
2.  
3.  
From home, tap  
Tap a call record, and then tap  
Enter recipients for the message, and then tap  
Phone > Logs.  
Menu > Send number.  
Send.  
Add Numbers to the Reject List from Logs  
You can save numbers from recent logs to the reject list, to automatically reject incoming calls from  
the number. For more information about rejecting calls automatically, see Call Rejection.  
1.  
2.  
From home, tap  
Phone > Logs.  
Menu > Add to reject list.  
Tap a call record, and then tap  
Delete Logs  
Follow these steps to clear the Logs list.  
n
From home, tap  
Phone > Logs.  
Phone Calls  
41  
 
l
l
To delete a single call record, touch and hold on a call record to mark it, and then tap  
Delete > OK.  
To delete multiple call records, touch and hold on a call record to mark it, and continue  
tapping call records to mark them for deletion. Tap  
calls.  
Delete > OK to delete all the marked  
Access Call Settings  
You can access Call Settings from the phone app or through the main Settings menu.  
n
From the Phone app: From home, tap  
Phone >  
Menu > Settings > Call.  
n
From Settings: From home, tap  
Apps >  
Settings >  
Call.  
For details about Call settings, see Call Settings.  
Phone Calls  
42  
 
Contacts  
The Contacts application lets you store and manage contacts from a variety of sources, including  
contacts you enter and save directly in your phone as well as contacts synchronized with your  
Google account, your PC, compatible email programs (including Exchange Server), and your  
Facebook friends.  
Get Started With Contacts  
When you set up an account on your phone, the contacts you have stored in the account are also  
available on your phone. When you add contacts, you can choose to save the contacts to the phone,  
or to one of the accounts you have set up on the phone.  
n
n
n
n
Google contacts are synchronized between your phone and a Google account you set up on  
your phone.  
®
Microsoft Exchange ActiveSync contacts are synchronized between your phone and an  
®
®
Exchange Server or Microsoft Outlook account set up on your phone.  
Samsung account contacts are synchronized between your phone and your Samsung  
account, if you have a Samsung account set up on your phone.  
Device contacts are stored locally on the phone.  
Note: If you ever perform a factory reset on your phone, contacts stored on the device will be lost.  
Access Contacts  
There are a couple of ways to access Contacts.  
n
From home, tap  
– or –  
Apps >  
Contacts.  
From home, tap  
Phone > Contacts.  
Find a Contact  
You can search for a contact, or scroll the list to find one by name.  
Contacts  
43  
       
1.  
From home, tap  
Apps >  
Contacts.  
2. Tap the Search field, and then enter characters to find contacts that match.  
– or –  
Tap a letter on the side of the list to go directly to that letter in the alphabetical list.  
Access Contacts Settings  
Choose options for contacts, including choosing how contacts display, importing and exporting  
contacts, and more.  
You can access Contacts Settings in two ways:  
n
From the Contacts app: From home, tap  
Contacts >  
Menu > Settings > Contacts.  
n
From Settings: From home, tap  
Apps >  
Settings >  
Contacts.  
For details about Contacts settings, see Contacts Settings.  
Add a Contact  
You can add contacts directly from the Contacts application. Enter details such as name, phone  
numbers, email addresses, mailing addresses, and more.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap  
Add, and then touch contact fields to enter information.  
l
Tap  
to choose a storage account for the contact. You can choose Device to store the  
contact on the phone, or choose an account.  
l
Tap  
to assign a picture to the new contact:  
o
Image: Choose a picture from Gallery.  
o
o
Tagged pictures: Choose a tagged photo from Gallery.  
Take picture: Take a new picture.  
l
Tap the Name field to use the onscreen keyboard to enter the full name. Tap  
for  
additional name fields.  
Contacts  
44  
     
l
Tap the Phone number field, and then enter the phone number. Tap  
to add another  
Phone number. Tap to choose a label for the number. If you add more than one  
phone number, you’ll be prompted to choose a default phone number. The default phone  
number is the one your phone will use in most cases.  
l
Tap  
beside Email to enter an email address. If you add more than one email address,  
you’ll be prompted to choose a default email address. The default email address is the one  
your phone will use in most cases.  
l
l
l
Tap Groups to assign the contact to a group.  
Tap Ringtone to choose a ringtone to play for calls from the contact.  
Tap Add another field to add new fields for the contact.  
3. Tap Save to save the new contact.  
Save a Phone Number  
You can save a phone number to Contacts directly from the phone keypad.  
1.  
From home, tap  
Phone.  
2. Enter a phone number using the onscreen keypad.  
3. Tap Add to Contacts, and then tap Create contact or Update existing.  
4. Continue adding information for the contact, as desired.  
5. Tap Save to save the contact.  
Note: If you have accounts set up on your phone, you can save the contact to an account.  
Edit a Contact  
Once you’ve added a contact, you can add or edit any of the information in the entry, assign a  
picture, customize it with a unique ringtone, and more.  
Add or Edit Information for a Contact  
You can modify existing contact information to keep your information up-to-date.  
Contacts  
45  
     
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Edit.  
Tap a contact to display it, and then tap  
3. Tap any field you want to change or add. See Add a Contact.  
4. Add or edit the information, and then tap Save.  
Assign a Picture to a Contact  
Adding a picture to a contact entry creates a more personal and easily recognized entry. For  
example, when receiving a call from one of your contacts, the associated picture will display. You  
can assign a picture from Gallery, or take a new picture with Camera.  
1.  
2.  
3.  
From home, tap  
Apps >  
Contacts.  
Edit.  
Tap a contact to display it, and then tap  
Tap  
to assign a picture to the contact:  
l
l
l
Image: Choose a picture from Gallery.  
Tagged pictures: Choose a tagged photo from Gallery.  
Take picture: Take a new picture.  
4. Follow the prompts to save the picture to the contact.  
Assign a Ringtone to a Contact  
You can assign a special ringtone to individual contacts for more personalization.  
1.  
From home, tap  
Apps >  
Contacts.  
2. Tap a contact to display it, and then tap the Ringtone field.  
3. Choose a ringtone preloaded on your phone, or tap Add to choose a song from Music.  
4. Tap OK to assign the ringtone.  
Link Contacts  
When you have contacts from various sources (Gmail, phone, Facebook, etc.), you may have  
multiple similar entries for a single contact. Your phone’s Contacts application lets you link multiple  
Contacts  
46  
     
entries into a single contact.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Menu > Link contacts.  
Tap a contact to display it, and then tap  
3. Tap another entry to link it to the original contact.  
Note: You can link up to five contacts in a single entry.  
Delete Contacts  
You can delete a single contact, or choose multiple contacts to delete.  
Delete a Contact  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Menu > Delete > OK.  
Tap a contact to display it, and then tap  
Delete Multiple Contacts  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Delete, and then tap contacts to select them, or tap Select all.  
3. Tap Done, and then tap OK to confirm the deletion.  
Save a Business Card as a Contact  
Take a picture of a business card, and your phone recognizes the information to save the business  
card in Contacts, and create a new contact from the info on the business card.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Add.  
Tap Menu > Business cards >  
3. When the camera opens, center the business card in the guidelines on the screen. If the Camera  
can recognize the business card, it will take the picture automatically, or you can take the picture  
manually.  
4. Your phone analyzes the picture of the business card, and uses information it recognizes to  
create a new contact. You can also add more information to the contact.  
5. Tap Save to save the new contact. The business card is displayed as the picture for the contact.  
Contacts  
47  
   
Tip: You can view all your business cards by tapping  
Menu > Business cards.  
Merge Contacts  
If you have accounts set up on your phone, you can merge device contacts with the account’s  
contacts. Device contacts are stored only in the phone’s memory, and could be lost if you lose your  
phone or reset it to the factory defaults. Merging with an account means the contacts are synced with  
the account and stored there.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Merge accounts.  
3. Choose an account to merge with, and then follow the prompts to complete the merge.  
Speed Dials  
Speed dials are 1-to-3 digit shortcuts you can assign to contacts, to make dialing faster. Speed dial 1  
is reserved for Voicemail.  
Assign Speed Dials  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Speed dial.  
3. Tap an unused speed dial, and then select a contact to assign to the number.  
Remove Speed Dials  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Speed dial, and then tap X beside the speed dials you want to remove.  
Make a Call With a Speed Dial  
1.  
From home, tap  
Phone.  
2. Touch the speed dial digits, holding the last digit until the number dials.  
Contacts  
48  
   
Favorites  
The Favorites tab is a listing that can help you quickly access your most used or preferred Contacts  
entries.  
Mark Contacts as Favorites  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Favorite to turn the star yellow.  
Tap a contact to display it, and then tap  
Remove Contacts from Favorites  
1.  
Contacts.  
From home, tap  
Apps >  
2. Tap Favorites, and then touch and hold on a contact to select it. You can also tap other  
contacts, or choose Select all to select all contacts.  
3.  
Tap  
Make a Call from Favorites  
1.  
Delete.  
From home, tap  
Apps >  
Contacts.  
2. Tap Favorites, and then tap a contact to dial the contact’s default telephone number. The  
default number is set in contacts, when you enter multiple phone numbers for a contact.  
Create a Shortcut to a Favorite  
You can create a shortcut to a favorite, to access their information directly from the home screen.  
1.  
From home, tap  
Apps >  
Contacts.  
2. Tap Favorites, and then touch and hold on a contact to select it.  
3.  
Tap  
Menu > Add shortcut to home screen. The new shortcut displays in an empty area  
of the home screen.  
Groups  
You can use groups to organize your contacts. Your phone comes with preloaded groups, and you  
can create your own. You might create a group for your family, for coworkers, or a team. Groups  
make it easy to find contacts, and you can send messages to the members of a group.  
Contacts  
49  
   
Create a Group  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Groups, and then tap  
Add.  
3. Tap fields to enter information about the group:  
l
Tap Create group in to choose where to save the group. You can save it to a specific  
account, to the device memory, or to all accounts.  
l
l
Tap Group name to enter a name for the new group.  
Tap Group ringtone to select a ringtone for notifications for incoming calls from group  
members.  
l
l
Tap Group message tone to select a ringtone for notifications for new messages from  
group members.  
Tap Group vibration pattern to select a vibration pattern for alerts to incoming calls or  
messages from group members.  
4. Tap Add member and select a member or members to add to the new group, and then tap  
Done.  
5. Tap Save to save the new group.  
Add Contacts to a Group  
1.  
2.  
3.  
From home, tap  
Apps >  
Contacts.  
Tap  
Tap  
Groups, and then tap a group.  
Add, and then tap the contact(s) you want to add.  
4. Tap Done.  
Send a Message to a Group  
You can send a message to members of a group, if the members have a telephone number stored in  
their contact record.  
A message to multiple recipients is treated as a group conversation.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Groups, and then tap a group.  
Contacts  
50  
3.  
Tap  
Menu > Send message or email > Message.  
4. Tap contacts to select them, or tap Select all and tap Done.  
5. Continue to enter your message and send it. For more information, see Text and Multimedia  
Messaging.  
Send an Email to a Group  
You can send an email to members of a group, if the members have an email address stored in their  
contact record.  
1.  
2.  
3.  
From home, tap  
Apps >  
Contacts.  
Tap  
Tap  
Groups, and then tap a group.  
Menu > Send message or email > Email.  
4. Tap contacts to select them, or tap Select all and tap Done. Note that you’ll only see group  
members that have email addresses in their contact records.  
5. Continue to choose an email account, or Gmail, and then enter your email and send it. For more  
information, see Compose and Send Email.  
Share Contacts  
You can quickly share contacts via Bluetooth, Email, Gmail, Messages, or Wi-Fi Direct, or you can  
add them to Dropbox or send them to print.  
Send Contact Information  
You can copy a contact’s information into a text message and send it.  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Menu > Send contact information.  
Tap a contact to display it, and then tap  
3. Choose information to send, and then tap Done.  
4. Enter a recipient, and then continue with the text message. For more information on text  
Share a Name Card  
When you share a name card, the contact’s information is sent as a vCard file (.vcf). You can attach  
a vCard to a message, or save it to a storage location.  
Contacts  
51  
 
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Menu > Share name card.  
Tap a contact to display it, and then tap  
3. Choose a sharing method:  
l
Add to Dropbox: Save the contact to your Dropbox account, if you have one set up on your  
phone.  
l
Bluetooth: Send the information via Bluetooth. See Bluetooth for information on pairing and  
sending via Bluetooth.  
l
l
Drive: Save the contact to Google Drive.  
Email: Attach the contact to a new Email message. If prompted, select an email account.  
See Compose and Send Email for details on sending email.  
l
l
Gmail: Send the information as a Gmail attachment. See Send a Gmail Message for details.  
Messages: Attach the contact to a message (adding an attachment converts the message to  
MMS). For more information on messaging, see Text and Multimedia Messaging.  
l
Wi-Fi Direct: Transfer the contact via a peer-to-peer Wi-Fi connection. For more  
information, see Wi-Fi Direct Settings.  
Export and Import Contacts  
You can import or export contacts from the phone’s memory (USB storage), or from an optional,  
installed memory card (SD card, not included). You might have contacts stored in phone memory or  
on a memory card if you are moving from an old phone, or if you received them via Bluetooth from  
another device.  
Contacts you export are saved as namecards (.vcf), which can be imported into other apps or  
devices that support the namecard format.  
Export Contacts  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Settings > Contacts > Import/Export.  
3. Choose an option:  
l
Export to USB storage: Save the contacts to the phone’s memory.  
Export to SD card: Save the contacts to an optional installed memory card.  
l
4. Tap OK to complete the export.  
Contacts  
52  
 
Import Contacts  
1.  
2.  
From home, tap  
Apps >  
Contacts.  
Tap Menu > Settings > Contacts > Import/Export.  
3. Choose an option:  
l
Import from USB storage: Save contacts from the phone’s memory.  
Import from SD card: Save contacts from an optional installed memory card.  
l
4. Choose an account for the imported contacts, or choose Device to import the contacts to the  
device.  
Contacts  
53  
Accounts and Messaging  
With Sprint service and your phone’s messaging capabilities, you have the opportunity to share  
information through many different channels and accounts.  
Google Account  
Many of your phone’s applications, such as Gmail, Google Maps, Google Hangouts, and the Google  
Play Store, require a free Google account. To use these applications, you must set up your Google  
account on your phone. Setting up your account on your phone syncs your phone and your online  
Google account.  
Create a Google Account  
If you do not already have a Google account, you can create one using your phone. The first time you  
turn on your phone, the setup process prompts you to sign in to your Google account, or you can sign  
in anytime.  
Although you need a Gmail account to use certain features of your phone, such as Google Play, you  
do not need to use Gmail as the default account for your phone.  
1.  
From home, tap  
Apps >  
Settings.  
2. Tap Accounts > Add account > Google > New.  
3. Follow the onscreen prompts to create your free account.  
Sign In to Your Google Account  
If you have a Google Account but have not yet signed in with your phone, follow these instructions to  
sign in to your Google Account.  
1.  
From home, tap  
Apps >  
Settings.  
2. Tap Accounts > Add account > Google > Existing.  
3. Follow the prompts to enter your Google account and password, and choose options for your  
account on your phone.  
Access Gmail  
After you set up your Google account on your phone, you can access Gmail from your phone.  
Accounts and Messaging  
54  
         
1.  
From home, tap  
Google >  
Gmail.  
2. Do any of the following:  
l
l
l
Swipe your finger up the screen to view more messages and conversations.  
Tap a message or conversation to read it.  
If you have more than one Google account set up on your phone, tap the menu at the top of  
the screen to choose an account to view.  
Send a Gmail Message  
Send and receive Gmail from your phone.  
1.  
2.  
From home, tap  
Google >  
Gmail.  
From the Inbox, tap  
, and then enter the email address(s) in the To field. To send a carbon  
copy (Cc) or a blind carbon copy (Bcc) of the email to other recipients, tap  
Menu > Add  
Cc/Bcc.  
3. Tap the Subject field and enter the email subject.  
4.  
5.  
Tap the Compose email field and compose your email. To add an attachment, tap  
Attach file.  
Menu >  
To send the message, tap  
Send.  
l
To save the current email as a draft, tap  
Menu > Save draft. To view your draft email  
messages, from the Inbox, tap Inbox and then tap Drafts.  
l
To delete the current email message, tap  
Menu > Discard.  
Read and Reply to Gmail Messages  
Below are procedures for reading and replying to Gmail messages.  
1.  
From home, tap  
Google >  
Gmail.  
2. Tap a message to display its contents.  
Accounts and Messaging  
55  
   
3.  
Tap  
Reply to display the reply screen.  
4. Tap the menu at the top of the screen, and then tap Reply, Reply All, or Forward.  
5.  
To send the message, tap  
Send.  
Tip: You can also access new messages from the Notification panel. When a new Gmail message  
arrives, you’ll see the icon in the status bar. Touch and hold the bar and slide it down to display the  
Notification panel. Tap a message to display it.  
Samsung Account  
Create a Samsung account, for access to Samsung apps and services, such as Samsung Hub,  
Samsung Apps, Samsung Link, and much more.  
When you sign in to your Samsung account on your phone, you can access Samsung-specific  
content and features.  
1.  
From home, tap  
Apps >  
Settings.  
2. Tap Accounts > Add account > Samsung account, and then tap Sign in or Create new  
account.  
3. Follow the prompts to sign into your account, or create a new account.  
Note: Tap Help for more information about Samsung accounts, or for help with your account.  
Email  
Use the Email application to send and receive email on your phone.  
Add an Email Account  
Email allows you to send and receive email using various email services. You can also receive text  
message alerts when you receive an important email.  
Note: If your phone does not recognize the type of account you want to set up, you may need to  
consult the account administrator for some information, such as incoming and outgoing server  
settings, before you set up the account.  
1.  
From home, tap  
Apps >  
Email.  
Accounts and Messaging  
56  
     
2. Enter your email address in the Email address field.  
3. Enter your password in the Password field. To see your password as you enter it, tap Show  
password.  
4. Tap Next to start automatic email setup. If you need to configure custom settings, tap Manual  
setup and then enter your settings. These may include mail type, user name, password, server,  
security type, etc.  
5. Follow the onscreen prompts to configure options for the account.  
6. Tap Done to complete setup.  
Add Additional Email Accounts  
If you already have an email account set up on your phone, you can still add a new account from  
Email.  
1.  
2.  
3.  
From home, tap  
Apps >  
Email.  
Tap  
Menu > Settings > Manage accounts.  
Tap  
Add, and then follow the prompts to enter your log in credentials and configure options  
for the account.  
Note: You can also add email accounts from Settings. From home, tap  
Apps >  
Settings >  
Accounts > Add account > Email.  
Add a Microsoft Exchange ActiveSync Account  
You can set up your Microsoft Exchange ActiveSync account on your phone, to sync your email,  
Contacts, and Task information between your phone and account.  
Note: Before setting up a Microsoft Exchange ActiveSync Account, contact your company’s  
Exchange Server administrator for information you’ll need while setting up the account.  
1.  
From home, tap  
Apps >  
Settings >  
Accounts > Add account > Microsoft  
Exchange ActiveSync.  
2. Enter your email address in the Email address field.  
3. Enter your password in the Password field. To see your password as you enter it, tap Show  
password.  
4. Tap Manual setup and then enter your settings. You may need to consult your network  
administrator for this information:  
l
Domain\username: Enter your network domain and username, separated by “\”.  
Accounts and Messaging  
57  
 
l
l
Password: Enter your network access password (case-sensitive).  
Exchange server: Enter your system’s Exchange server remote email address. Obtain this  
information from your company network administrator.  
l
l
Use secure connection (SSL): Tap to place a checkmark in the box, if your system  
requires SSL encryption.  
Use client certificate: Tap to place a checkmark in the box, if your system requires  
certification.  
5. Follow the onscreen prompts to configure options for the account.  
6. Tap Done to complete setup.  
Note: You can also add email accounts from the Email app.  
Compose and Send Email  
Compose and send email using any account you have set up on your phone. Increase your  
productivity by attaching files such as pictures, videos, or documents to your email messages.  
1.  
2.  
From home, tap  
Apps >  
Email.  
From the Inbox, tap  
.
3. Tap fields to compose your message:  
l
l
Tap the To field and enter the recipient’s email address. You can add multiple message  
recipients.  
To send a carbon copy (Cc) or a blind carbon copy (Bcc) of the current email to other  
recipients, tap  
, and then tap Cc or Bcc.  
l
l
Tap the Subject field and enter the email subject.  
Tap the text entry field and compose your email.  
o
To add an attachment, tap  
. Choose My Files, Images, Take picture, Video, Record  
video, Audio, Record audio, Memo, Calendar, Contacts, or Maps.  
o
Tap  
Menu for more options, including Send email to myself, Scheduled email,  
Priority, and Security options.  
4.  
To send the message, tap  
.
Accounts and Messaging  
58  
 
Reply To or Forward Email  
Reading and replying to email on your phone is as simple as on your computer.  
1.  
From home, tap  
Apps >  
Email.  
2. On the email account Inbox, tap a message to view it.  
3. Choose an option:  
l
Reply: Send a message to the original sender.  
l
Reply all: Send a reply to the original recipient list.  
l
Forward: Send the message to new recipient(s).  
4.  
Enter a message (if desired) and then tap  
.
Manage Your Email Inbox  
The following procedures allow you to view, refresh, sort, and delete your email messages.  
View Your Email Inbox  
1.  
From home, tap  
Apps >  
Email.  
2. If you have multiple accounts set up on your phone, tap the toolbar at the top of the screen and  
then choose one from the menu.  
Synchronize an Email Account  
Whatever your automatic synchronization settings are, you can also synchronize your sent and  
received email messages manually at any time.  
1.  
From home, tap  
Apps >  
Email.  
2. Select an email account.  
l
If you are already in an email account, tap the account name field (upper-left) to open the  
complete email account list page.  
l
Select an available email account.  
3.  
Tap  
Sync.  
Accounts and Messaging  
59  
   
Filter Email Messages  
1.  
2.  
From home, tap  
Apps >  
Email.  
On the email account Inbox, tap  
> Filter by.  
3. Select an option, to display messages that match the filter.  
Delete an Email Message  
1.  
2.  
From home, tap  
Apps >  
Email.  
Touch and hold the message you want to delete, and then tap  
– or –  
Delete.  
Tap an email to display it, and then tap  
Delete.  
3. Follow the prompts to confirm the deletion.  
Delete Multiple Email Messages  
1.  
2.  
From home, tap  
Apps >  
Email.  
Tap  
Menu > Delete, and tap the check boxes beside messages you want to delete.  
– or –  
Touch and hold on a message you want to delete, and then tap check boxes for additional  
messages to delete.  
3. Follow the prompts to confirm the deletion.  
Edit Email Settings  
You can edit general preferences, which apply to all email accounts, or configure settings for specific  
email accounts, such as email address and password, name display and signature, frequency of  
retrieval, and more.  
You can access Email settings in two ways:  
n
From the Email app: From home, tap  
Apps >  
Email >  
Menu > Settings.  
n
From Settings: From home, tap  
Apps >  
Settings >  
Email.  
Accounts and Messaging  
60  
 
For details about Email settings, see Email Settings.  
Delete an Email Account  
If you no longer want an email account on your phone, you can remove it.  
1.  
2.  
From home, tap  
Apps >  
Email.  
Tap  
Menu > Settings > Manage accounts, and then choose an option:  
l
If you only have one email account set up, tap  
Delete.  
Menu > Delete account.  
l
If you have more than one email account set up, tap  
3. Tap an account to mark it for deletion.  
4. Tap Done > OK to delete the account.  
Text and Multimedia Messaging  
With Text Messaging (SMS), you can send and receive text messages between your phone and  
another phone that supports messaging.  
Multimedia messages, (MMS), can contain text and pictures, recorded voice, audio or video files,  
picture slideshows, contact namecards (vCard), or calendar events (vCalendar).  
See your service plan for applicable charges for messaging.  
Send a Text Message (SMS)  
Quickly compose and sent text messages on your phone.  
1.  
2.  
From home, tap  
Messages.  
Tap New message.  
3. Tap Enter recipients, and then enter a contact name, a mobile phone number, or an email  
address using the onscreen keyboard. As you enter letters, possible matches from your  
accounts and contacts display on the screen. Touch a match to add it to the message.  
4. Tap Enter message and enter your message.  
5.  
Review your message and tap  
Send.  
Accounts and Messaging  
61  
     
Send a Multimedia Message (MMS)  
When you need to add a little more to a text message, you can send a multimedia message (MMS)  
text and pictures, recorded voice, audio or video files, picture slideshows, contact namecards  
(vCard), or calendar events (vCalendar).  
Composing MMS messages is the same as composing text messages, except that you attach a file  
to the message.  
1.  
2.  
From home, tap  
Messages.  
Tap New message.  
3. Tap Enter recipients, and then enter a contact name, a mobile phone number, or an email  
address using the onscreen keyboard. As you enter letters, possible matches from your  
accounts and contacts display on the screen. Touch a match to add it to the message.  
4. Tap Enter message and enter your message.  
5.  
To add an attachment, tap  
, and then select a file to attach:  
l
Image: Choose a picture from Gallery.  
l
Take picture: Launch the Camera to take a photo, and then add it to your message by  
tapping Save.  
l
l
Video: Choose a video from Gallery.  
Record video: Launch the Camera to record a video, and then add it to your message by  
tapping Save.  
l
l
l
l
l
l
l
Audio: Choose a sound from Music.  
Record audio: Launch Voice Recorder to record a new sound.  
Memo: Launch Memo to choose or create a memo. For more information, see Memo.  
Calendar: Add an event from your calendar.  
My location: Attach a map showing your location.  
Maps: Attach a map.  
Contacts: Add a contact entry (namecard) to the message.  
5.  
Review your message and tap  
Send.  
Accounts and Messaging  
62  
 
Save and Resume a Draft Message  
If you tap  
Back while composing a text or multimedia message, or leave the Messages screen,  
the message is automatically saved as a draft.  
To resume composing a Draft message:  
1.  
From home, tap  
Messages.  
2. On the Messages screen, tap the message with the with Draft marked.  
3.  
When you finish editing the message, tap  
Send.  
New Messages Notification  
Depending on your notification settings, the phone will play a ringtone, vibrate, or display the  
message briefly in the status bar when you receive a new text or multimedia message. To change  
the notification for new text and multimedia messages, see Access Messages Settings for details.  
A new message icon  
also appears in the notifications area of the status bar to notify you of a  
new text or multimedia message. The Messages app icon  
messages.  
also displays the number of new  
n
To open the message, touch and hold the status bar, and then slide the status bar down to open  
the Notification panel. Tap the new message to open and read it. For information on reading and  
replying to messages see Managing Conversations.  
Managing Conversations  
Text and multimedia messages that are sent to and received from a contact (or a number) are  
grouped into conversations or message threads in the Messages screen. Threaded text or  
multimedia messages let you see all the messages you exchange with a contact on the screen,  
similar to a chat program.  
To read a text message:  
n
On the Messages screen, tap the text message or conversation to open and read it.  
n
If you have a new message notification, slide the status bar down to open the Notification panel.  
Tap the new message to open and read it.  
Note: To view the details of a particular message, in the conversation, touch and hold the message  
to open the options menu, and then tap View message details.  
Accounts and Messaging  
63  
     
If a message contains a link to a Web page, tap the message and then tap the link to open it in the  
Web browser.  
If a message contains a phone number, tap the message and then tap the phone number to dial the  
number or add it to your contacts.  
To view a multimedia message (MMS):  
1.  
From home, tap  
Messages.  
2. From the message list, tap a message to display it.  
3. While the message is open, tap the play icon (on a video or audio file) to play back the file or tap  
an image to view a picture.  
Note: The file attachment on a MMS message can be saved to an optional installed memory card  
(not included). Touch and hold on the attachment, and then tap Save attachment. Select the  
attachment check box and tap Save.  
Reply to a Message  
1.  
From home, tap  
Messages.  
2. From the message list, tap a message.  
3. Tap the Enter message field and then type your reply message.  
4.  
When the message is complete, tap  
Send.  
Protect a Message from Deletion  
You can lock a message so that it will not be deleted even if you delete the other messages in the  
conversation.  
1.  
From home, tap  
Messages.  
2. On the Messages screen, tap a conversation.  
3. Touch and hold the message that you want to lock.  
4. Tap Lock on the options menu. A lock icon displays at the lower right hand side of the message.  
Delete a Conversation  
1.  
From home, tap  
Messages.  
2. Touch and hold the conversation you want to delete.  
3.  
Tap  
Delete > OK.  
Accounts and Messaging  
64  
Delete Multiple Conversations  
1.  
2.  
From home, tap  
Messages.  
Tap Menu > Delete.  
3. Select the conversations you want to delete, and then tap Done > OK.  
Note: Locked messages will not be deleted, unless you select the Include protected messages  
check box before confirming the deletion.  
Delete a Message  
1.  
From home, tap  
Messages.  
2. While viewing a conversation, touch and hold the message that you want to delete.  
3. Tap Delete on the options menu, and then follow the prompts to confirm the deletion.  
Access Messages Settings  
The messages settings menu lets you control options for your text and MMS messages including  
message limits, size settings, and notifications.  
You can access Message settings in two ways:  
n
From the Messages app: From home, tap  
Messages >  
Menu > Settings.  
n
From Settings: From home, tap  
Apps >  
Settings >  
Messages.  
For details about Messages settings, see Messages Settings.  
Note: If you choose a default messaging app other than Messages (for example, Google Hangouts),  
you will not be able to use the Messages app unless you restore it as the default messaging app. For  
Messaging Plus  
Messaging Plus gives you the highest quality video calling, group chat, and sharing experience on  
mobile. Share your favorite photos, videos, and current location.  
n
From home, tap  
Apps >  
Messaging+.  
Accounts and Messaging  
65  
   
Social Networking Accounts  
Stay in touch on the go with all your social networking accounts. Post updates on Facebook and  
®
®
Twitter , review your LinkedIn contacts, see what everyone’s talking about on YouTube™, and  
more.  
Facebook  
Post updates, read what your friends are up to, upload pictures and check-ins, and more with on-  
the-go Facebook access.  
Install the Facebook App on Your Phone  
Before you use Facebook on your phone, you must download and install the app from the Google  
Play Store app.  
1.  
From home, tap  
Play Store.  
2. Touch the Search icon and search for "facebook".  
3. Touch Facebook from the results list.  
4. Touch Install, and then touch Accept.  
5. When the download and installation is complete, touch Open. To open the app from the home  
screen, touch  
Apps > Facebook.  
Sign in to Your Facebook Account from Settings  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Accounts > Add account.  
3. Touch Facebook, and then follow the prompts to enter your Facebook account details and  
complete sign-in.  
YouTube  
YouTube is a video sharing website on which users can upload and share videos. The site is used to  
display a wide variety of user-generated video content, including movie clips, TV clips, and music  
videos, as well as video content such as video blogging, informational shorts, and other original  
videos.  
Accounts and Messaging  
66  
     
YouTube is a data-intensive feature. Sprint recommends that you upgrade to an unlimited data plan  
to avoid unexpected data charges.  
1.  
2.  
From home, tap  
Google >  
YouTube.  
Tap  
to enter keywords in the Search field to search for specific videos, scroll down to  
browse through the main page thumbnails, or scroll to the bottom to explore additional options.  
3. To view a video, tap an available preview thumbnail or tap the title link.  
Note: It is not necessary to sign in to YouTube to view content. However, if you wish to sign in to  
access additional options, tap  
Menu > Sign in. Select an account (if available) or create a new  
account. (Even if you sign in to YouTube via the Web, you must separately sign in via your phone.)  
Google+  
Google+™ makes messaging and sharing with your friends a lot easier. You can set up Circles of  
friends, visit the Stream to get updates from your Circles, use Messenger for fast messaging with  
everyone in your Circles, or use Instant Upload to automatically upload videos and photos to your  
own private album on Google+.  
Visit www.google.com/mobile/+/ for more information.  
Google+ is part of your Google account, and uses your Google account sign-in. Before using  
Google+, set up your Google account on your phone. For more information, see Create a Google  
1.  
From home, tap  
Google >  
Google+.  
2. If you are signed into more than one Google account, choose an account to use with Google+.  
3. Follow the onscreen instructions to use Google+.  
Hangouts  
Hangouts is an application for instant messaging offered by Google. Conversation logs are  
automatically saved to a Chats area in your Gmail account. This allows you to search chat logs and  
store them in your Gmail accounts.  
1.  
From home, tap  
Apps >  
Hangouts.  
2. If you have already signed in to a Google account, it displays on the Hangouts screen.  
– or –  
Accounts and Messaging  
67  
   
If you have not already signed in to a Google account, tap ADD ACCOUNT, and then tap New  
to create a new Google account, or tap Existing to sign in to an existing Google account.  
3. Follow the prompts to begin using Google Hangouts.  
Note: You can use Hangouts as your phone’s default messaging app, or as a standalone IM app. If  
you set Hangouts as the default messaging app, the Messages app will be disabled. For more  
information, see Default Messaging App Settings.  
Accounts and Messaging  
68  
Apps and Entertainment  
All your phone’s features are accessible through the Applications list.  
Note: Available apps and services are subject to change at any time.  
Google Play Store  
The Google Play™ Store app is the place to go to find new Android apps, games, movies, music,  
and books for your phone. Choose from a wide variety of free and paid apps ranging from  
productivity apps to games. When you find an app you want, you can easily download and install it  
on your phone.  
To access the Google Play Store app, you must first connect to the Internet using your phone’s Wi-Fi  
or Sprint 4G or 3G data connection and sign in to your Google Account. See Web and Data and  
Google Account for details.  
Important: Sprint’s policies often do not apply to third-party applications. Third-party applications  
may access your personal information or require Sprint to disclose your customer information to the  
third-party application provider. To find out how a third-party application will collect, access, use, or  
disclose your personal information, check the application provider’s policies, which can usually be  
found on their website. If you aren’t comfortable with the third-party application’s policies, don’t use  
the application.  
Find and Install an App  
When you install apps from the Google Play Store app and use them on your phone, they may  
require access to your personal information (such as your location, contact data, and more) or  
access to certain functions or settings of your phone. Download and install only apps that you trust.  
Note: You need a Google Wallet account to purchase items from the Google Play Store app. See  
Create a Google Wallet Account to set up a Google Wallet account if you do not have one.  
1.  
From home, tap  
Play Store.  
2. Browse through the categories to find and learn about apps.  
3. Tap Install (for free applications) or the price (for paid applications).  
4. Follow the prompts to learn about how the app uses your personal information, or access to  
certain functions or settings of your phone. If you agree to the conditions, tap Accept (for free  
apps) or Accept and then Buy (for paid apps) to begin downloading and installing the app.  
Apps and Entertainment  
69  
     
Warning: Read the notification carefully! Be especially cautious with apps that have access to  
many functions or a significant amount of your data. Once you agree to the download and installation  
on this screen, you are responsible for the results of using this item on your phone.  
Create a Google Wallet Account  
You must have a Google Wallet account associated with your Google Account to purchase items  
from the Google Play Store app.  
The first time you turn on your phone, the setup process will prompt you to create a Google Wallet  
account. If you did not create one at setup, you can create an account at any time using one of these  
methods:  
n
On your computer, go to google.com/wallet/ to create a Google Wallet account.  
– or –  
The first time you use your phone to buy an item from Google Play, follow the prompts to enter  
your billing information to set up a Google Wallet account.  
Warning: After you use Google Wallet to purchase an app from the Google Play Store, the phone  
remembers your password, so you don’t need to enter it the next time. For this reason, you should  
secure your phone to prevent others from using it without your permission. For more information,  
see Screen Lock.  
Open an Installed App  
After you install an app, it’s available in the Apps tray.  
n
From home, tap  
Apps, and then tap the app icon.  
Uninstall an App  
You can uninstall any app that you have downloaded and installed from Google Play.  
1.  
From home, tap  
Apps >  
Settings >  
Application manager.  
2. Tap the DOWNLOADED tab, and then select the app you want to uninstall.  
3. Tap Uninstall, and then follow the prompts to remove the app from your phone.  
Apps and Entertainment  
70  
     
Navigation  
Your phone offers a number of location-based navigation programs to help you figure out where you  
are and get you where you’re going.  
Google Maps  
Use the Google Maps™ application to find directions, location information, business addresses, etc.  
Determine your current location with or without GPS, get driving and transit directions, and find  
phone numbers and addresses for local businesses.  
For more information about Google Maps, visit maps.google.com.  
Enable Location  
To use Google Maps, enable your phone’s GPS location service and agree to share location  
information with Google.  
1.  
From home, tap  
Apps >  
Settings >  
Location.  
2. Tap the ON/OFF switch beside Location to turn the service on.  
To launch the Google Maps application:  
n
From home, tap  
Google >  
Maps.  
Scout  
Scout™ by Telenav is a daily personal navigator that helps you get where you’re going. It lets you  
see and hear turn-by-turn directions and it can provide important, personalized information about  
traffic and alternate routes.  
1.  
From home, tap  
Play Store.  
2. Touch the Search icon and search for "scout".  
3. Touch Scout from the results list.  
4. Touch Install, and then touch Accept.  
5. When the download and installation is complete, touch Open. To open the app from the home  
screen, touch  
Apps >  
Scout.  
Apps and Entertainment  
71  
     
Samsung Apps  
Browse, search, and find apps to download and install on your phone. Log in to your Samsung  
account to manage your downloads.  
n
From home, tap  
Apps >  
Samsung Apps.  
Music Apps  
Your phone lets you discover, download, and listen to your favorite music through a variety of  
applications.  
Note: For information about loading music onto your phone, see Transfer Files Between Your  
Phone and a Computer.  
Google Play Music  
Google Play Music lets you browse, shop, and play back songs purchased from the Google Play  
Store app, as well as songs you have loaded from your own music library. The music you choose is  
automatically stored in your Google Music library and instantly ready to play or download.  
For more information about Google Play Music, visit music.google.com.  
Note: For information about loading music onto your phone, see Transfer Files Between Your  
Phone and a Computer.  
n
From home, tap  
Google >  
Play Music.  
Music  
The Music app plays music files. Use Music to browse your music library, play songs, and create  
playlists. You can also set songs as ringtones for incoming calls, or as alarm tones.  
Note: For information about loading music onto your phone, see Transfer Files Between Your  
Phone and a Computer.  
When you close the Music screen, playback will continue in the background, so you can listen to  
music while you use other features of your phone. When music is playing in the background, you can  
access playback controls from the Notification panel.  
Apps and Entertainment  
72  
       
Play Music  
1.  
From home, tap  
Apps >  
Music.  
2. Tap the category tabs at the top of the screen. The default tabs are Playlists, Tracks, Albums,  
Artists, Music square, Folders, and Devices. You may have to swipe your finger right or left  
along the tabs to see all of them.  
3. Scroll through the list and tap a song to begin. While playing music, use these controls:  
l
Tap  
Tap  
to pause playback. To start playback again, tap  
.
l
l
to move to the previous song. Tap to move to the next song.  
Tap the repeat button to control playback. Choose  
to play all songs once. Choose  
to  
repeat all songs. Choose to repeat the current song.  
l
Tap the shuffle button to control the order songs are played. Choose  
order they appear in the list. Choose to play songs in random order.  
to play songs in the  
l
l
l
Tap  
to mark a song as a favorite. When a song is a favorite, the star is orange. Favorite  
songs are included in the Favorites playlist.  
Tap  
to set the volume, or tap  
to choose a SoundAlive option. You can also set  
volume by pressing the Volume key on the side of the phone.  
Tap  
to share music with nearby devices using Group Play.  
Use Playlists  
Create playlists to group songs, so you can listen to them together.  
1.  
From home, tap  
Apps >  
Music.  
2. Tap the Playlists tab, and then use these options:  
l
Tap an existing playlist to play its songs. While playing, tap  
Menu for playlist options.  
l
Tap  
Create playlist to create a new playlist. Follow the prompts to name the playlist,  
and then select songs for the playlist.  
l
Tap  
Menu for other options, including Edit title, to rename playlists.  
Note: While playing music, you can touch and hold on a song to choose Add to playlist.  
Apps and Entertainment  
73  
Set a Song as a Ringtone or Alarm Tone  
You can set a song as a ringtone for all incoming calls, or for a contact. You can also set a song as an  
alarm tone.  
1.  
From home, tap  
Apps >  
Music.  
2. Scroll to find a song, and then touch and hold on the song.  
3. Choose Set as, and then use these options:  
l
Choose how to use the song:  
o
From the beginning: Plays the song from the beginning.  
o
Auto recommendations: Plays the best part of the song, as detected by the Music app.  
l
Choose what to set the song as:  
o
Phone ringtone: Plays the song for all incoming calls.  
o
Caller ringtone: Plays the song for calls from a Contact.  
o
Alarm tone: Plays the song as the notification for alarms.  
4. After choosing options, tap Done, and then follow the prompts to complete the setup.  
Share Music  
You can share music with other nearby DLNA-compatible devices.  
Note: Your phone, and the other DLNA-compatible device, must be connected to the same Wi-Fi  
network, and the other device must have its Nearby devices feature turned on. For more  
information, For more information, see Nearby Devices Settings.  
1.  
From home, tap  
Apps >  
Music.  
2. Tap the Devices tab, and then select the target device from the list.  
Music Options and Settings  
1.  
2.  
From home, tap  
Apps >  
Music.  
Tap  
Menu for options. Available options depend on the tab:  
l
Select: Choose items.  
l
Add to playlist/Create playlist: Depending on the tab, you can add songs to a playlist, or  
create a new playlist.  
Apps and Entertainment  
74  
l
Listen via Bluetooth: Play music through a Bluetooth-compatible device that is paired with  
your phone. For more information about using Bluetooth, see Bluetooth.  
l
l
l
Grid view/List view: Choose a format for displaying items.  
Delete: On the Tracks or Playlists tabs, you can choose songs to delete, or delete playlists.  
Settings:  
o
Tabs: Choose tabs to display on the Music screen.  
o
Playlists: Choose default playlists. These default playlists will automatically update to  
include songs you play.  
o
SoundAlive: Choose a setting to match the type of music you’re playing.  
o
Adapt Sound: Customize sound output when you are listening with earphones. Only  
available when earphones or a headset are inserted into the 3.5mm Headset Jack.  
o
Play speed: Touch and drag the slider to set the default speed for music playback.  
o
Music auto off: Choose a time period for music to play, after which Music will close.  
o
Lyrics: When enabled, lyrics display for songs as they play, if the lyric information is  
stored in the music file.  
o
Smart volume: When enabled, Music automatically adjusts the volume of all songs to  
an equal level.  
Sprint Music Plus  
With Sprint Music Plus and the Music Store, Ringtone Store, and Ringback Tone Store, you can  
purchase, download, and play music, ringtones, and ringback tones for your phone.  
Install the Sprint Music Plus App on Your Phone  
Before you use Sprint Music Plus on your phone, you must download and install the app from the  
Google Play Store.  
1.  
From home, tap  
Apps >  
Play Store.  
2. Tap the Search icon and search for "sprint music plus".  
3. Tap Sprint Music Plus from the results list.  
4. Follow the prompts to download and install the app.  
5. When the download has completed, tap Open.  
Apps and Entertainment  
75  
 
Access Sprint Music Plus  
1.  
From home, tap  
Apps >  
Sprint Music Plus.  
2. The first time you launch the app, tap Accept to accept the Terms and Conditions.  
3. Tap a store option from the main page (Ringbacks Store, Music Store, or Ringtones Store), or  
tap  
> Music (under Library) to access your music.  
l
Tap the onscreen navigation tools to skip ahead or rewind. Touch  
additional options.  
at any time to see  
l
For more information, tap  
> Settings > About or Help.  
Note: If you have loaded music on to your phone from your computer (see Transfer Files Between  
Your Phone and a Computer), you will need to sync your music to listen to it through Sprint Music  
Plus. From the Sprint Music Plus app, tap  
> Settings > Synchronize your music library.  
Once synced, you will see your music in the library.  
Purchase and Download Music from the Sprint Music Plus Store  
From the Sprint Music Plus Store, you can shop for songs to purchase and download to your phone.  
1.  
From home, tap  
Apps >  
Sprint Music Plus > Music Store.  
2. Enter a song or artist in the search field or browse through options in the tabs in the center of the  
screen.  
3. Touch a song to select it. (The song information screen is displayed.)  
4.  
Follow the onscreen instructions to preview or purchase the song. Touch  
display the Sprint Music Plus menu.  
at any time to  
Tip: For ringtones or ringback tones, touch Ringtone Store or Ringback Tone Store from the  
Sprint Music Plus main menu.  
Google Play Movies & TV  
Google Play Movies & TV allows you to watch movies and TV shows purchased on Google Play.  
You can stream instantly on your Android phone or tablet, or download so you can watch from  
anywhere, even when you’re not connected. Also, get quick access to your personal video  
collection, including those taken on your phone or tablet.  
Learn more about Google Play Movies & TV at play.google.com/about/movies.  
Apps and Entertainment  
76  
 
n
From home, tap  
Google folder >  
Play Movies & TV.  
Google Play Books  
Discovering your favorite books and authors has never been easier. With Google Play Books, you  
can shop the world's largest selection of ebooks and read them anywhere you like - on a tablet,  
phone, ereader, or the Web.  
n
From home, tap  
Google folder >  
Play Books.  
Google Play Games  
Google Play Games is the easiest way for you to discover new games, track achievements and  
scores, and play with friends around the world. It brings all your gaming on Google Play together in a  
unified Android experience.  
n
From home, tap  
Google folder >  
Play Games.  
Google Play Newsstand  
With Google Play Newsstand, discover more of the news and magazines you care about all in one  
app on your Android tablet or phone. Enjoy breaking news and in-depth articles featuring audio,  
video and more. From sports, business, cooking, entertainment, fashion and more - now get both  
free and paid news plus subscribe to vibrant full HD magazines, all in one place. With hundreds of  
premier publishers - it’s all there, easy to follow, read, and share.  
n
Enjoy Read Now to find more of the articles you care about and discover new ones you will love.  
n
Explore categories like Arts & Photography, Business & Finance, Food & Drink and more and  
subscribe to topics tagged to the articles that interest you most  
n
n
Go Offline with any news edition, topic or magazine without missing a page. Bookmark news  
stories you don't have time to read for later.  
All in one - Google Play Newsstand is the new home for all your Google Currents subscriptions  
and Google Play Magazines. Now with one app and one tap, it’s never been easier to stay  
informed on the news of the day.  
Access Google Play Newsstand  
n
From home, tap  
Google folder >  
Play Newsstand.  
Apps and Entertainment  
77  
     
Sprint Money Express  
Make payments, purchases, and manage your cash from your Android phone or linked Visa Prepaid  
card. The Sprint Money Express™ app lets you send money to nearly anywhere in the world, load  
checks directly to your phone, get paid faster with direct deposit, pay bills using prepaid cash, and  
more, all from your Sprint Money Express account and right from your phone.  
n
From home, tap  
Apps >  
Sprint Money Express.  
Note: Available apps and services are subject to change at any time.  
Sprint Zone  
Access your Sprint account, get device information and help, find recommended apps, and more.  
1.  
From home, tap  
Apps >  
Sprint Zone.  
2. Touch My Account to sign in to and manage your Sprint account, My Device to access  
information about your phone, or touch any other category to explore additional options, such as  
Apps, Games, Sprint News, TV & Movies, Music & Tones, and more.  
Note: Sprint Zone categories and options are subject to change. Check back frequently for new  
content and updates.  
Sprint TV & Movies  
With Sprint TV & Movies, you can watch live TV and access movies and other on demand  
entertainment on the go.  
Note: Coverage not available everywhere. Content and lineup subject to change. Select channels  
also available for casual usage. Go to sprintchannels.mobitv.com for more information.  
Your Sprint TV Channel Options  
The Sprint TV application offers a wide variety of accessible channels. Subscription options include  
comprehensive basic packages as well as a full menu of “a la carte” channels. Visit  
sprintchannels.mobitv.com for more information on channels and pricing.  
Watch TV  
1.  
From home, tap  
Apps >  
Sprint TV & Movies.  
2. Follow the prompts to browse categories and find programs.  
Apps and Entertainment  
78  
     
l
l
l
Depending on your settings, your phone may prompt you to accept a data connection.  
You may be prompted to update your app. Tap Update to update Sprint TV & Movies.  
Browse horizontally through the category options in the center of the screen to see what's  
available. For quick access, touch a featured item in the center of the screen or select a live  
channel from the bottom bar.  
l
Scroll up and down in a category list and then touch a clip or channel to view the program.  
Note: The first time you access a channel that requires a subscription, you will be prompted to  
purchase access. Touch Subscribe to purchase access, or touch Preview to see a preview of the  
selected channel.  
NASCAR Mobile 2014  
Welcome to the 2014 NASCAR season! NASCAR MOBILE is designed to bring you what you, our  
fans, want directly to your Android device. Follow NASCAR News, Video Highlights, and immerse  
yourself even further into the NASCAR experience with driver informational stats, plus more.  
n
From home, tap  
Apps >  
NASCAR Mobile 2014.  
Note: Available apps and services are subject to change at any time.  
NBA Game Time  
The award-winning NBA Game Time is the official app to follow the NBA wherever you are!  
n
From home, tap  
Apps >  
NBA Game Time.  
Note: Available apps and services are subject to change at any time.  
NextRadio  
Listen to your favorite FM radio stations on the go with NextRadio. Tune in to any FM frequency in  
your area and listen to the radio without the hassle and cost of streaming music. Participating radio  
stations show you song information and artwork as you listen, so you can buy your favorite music,  
give feedback on the songs you like, and share what you’re listening to on Facebook or Twitter.  
NextRadio provides the radio experience today’s listeners have come to expect.  
n
From home, tap  
Apps >  
NextRadio.  
Note: Available apps and services are subject to change at any time.  
Apps and Entertainment  
79  
     
eBay  
At eBay we work hard every day to build a world-class online shopping experience on Android the  
eBay app is packed full of features that make it easy to browse, buy, sell, and manage your eBay  
experience whenever and wherever you are!  
n
From home, tap  
Apps >  
eBay.  
Note: Available apps and services are subject to change at any time.  
Eureka Offers  
Eureka is a unique, convenient, feature-packed shopping companion that provides discount  
opportunities for major brands and local merchants, all under one roof! Eureka provides unbeatable  
deals with a clean, easy-to-use package, with powerful features. Take advantage of discounts from  
major brands and local merchants, share your favorite deals with friends and family, access loyalty  
cards, and create/manage personalized product lists.  
n
From home, tap  
Apps >  
Eureka Offers.  
Note: Available apps and services are subject to change at any time.  
Apps and Entertainment  
80  
   
Web and Data  
The following topics address your phone’s data connections and the built-in Web browser.  
Additional data-related features can be found in Accounts and Messaging, Applications and  
Entertainment, and Tools and Calendar.  
Your phone’s data capabilities let you wirelessly access the Internet or your corporate network  
through a variety of connections, including:  
Wi-Fi  
Wi-Fi provides wireless Internet access over distances of up to 300 feet. To use your phone’s Wi-Fi,  
you need access to a wireless access point or “hotspot”.  
The availability and range of the Wi-Fi signal depends on a number of factors, including  
infrastructure and other objects through which the signal passes.  
Turn Wi-Fi On or Off  
When Wi-Fi is turned on, your device will notify you of available Wi-Fi networks, and you can connect  
to the Wi-Fi networks. Turn Wi-Fi off when not in use, to conserve battery power.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Wi-Fi, and then tap the ON/OFF switch beside Wi-Fi to turn Wi-Fi on or off.  
Note: You can also turn Wi-Fi on or off from the Notification panel. Drag down from the top of the  
screen, and then tap Wi-Fi.  
Turn Wi-Fi On and Connect to a Wireless Network  
By default, your phone’s Wi-Fi feature is turned off. Turning Wi-Fi on makes your phone able to  
discover and connect to compatible in-range Wi-Fi networks (or WAPs - wireless access points).  
Turn Wi-Fi On  
1.  
From home, tap  
Apps >  
Settings >  
Wi-Fi.  
2. Tap the ON/OFF switch to turn Wi-Fi on.  
Note: Wi-Fi networks are self-discoverable, which means no additional steps are required for your  
phone to connect to a Wi-Fi network. It may be necessary to provide a user name and password for  
certain closed wireless networks.  
Web and Data  
81  
       
Scan and Connect to a Wi-Fi Network  
1.  
From home, tap  
Apps >  
Settings >  
Wi-Fi.  
2. The network names and security settings (Open network or Secured) of detected Wi-Fi  
networks are displayed.  
l
When you select an open network, you will be automatically connected to the network.  
l
When you select a secured network, you will need to enter the wireless password to connect  
to the network. Enter the password and tap Connect. You can use the show password  
option to display the password as you enter it.  
Add a New Wi-Fi Network Manually  
1.  
From home, tap  
Apps >  
Settings >  
Wi-Fi.  
2. Tap Add Wi-Fi network.  
3. Enter the Network SSID. This is the name of the Wi-Fi network.  
4. Tap the Security field and select the security method used by the Wi-Fi network. If a password  
is required, enter it in the Enter password field.  
5. Tap Connect to store the new information and connect to the Wi-Fi network.  
Note: The next time your phone connects to a previously accessed or secured wireless network,  
you won’t be prompted to enter the wireless password again, unless you reset your phone back to its  
factory default settings.  
Connect to a Different Wi-Fi Network  
The following information is designed to help you connect your device to a different Wi-Fi network.  
1.  
From home, tap  
2. Detected Wi-Fi networks are displayed. To manually scan for available Wi-Fi networks, on the  
Wi-Fi settings screen, tap Menu > Scan.  
Apps >  
Settings >  
Wi-Fi.  
3. Tap another Wi-Fi network to connect to it.  
Note: If the wireless network you want to connect to is not in the list of detected networks, scroll  
down the screen, and tap Add Wi-Fi network. Enter the wireless network settings and tap  
Connect.  
Web and Data  
82  
Internet  
Your phone’s Internet browser gives you full access to both mobile and traditional websites on the  
go, using your phone’s 3G or 4G mobile data or Wi-Fi connections.  
n
From home, tap  
Internet.  
Note: The first time you launch Internet, you may be prompted to enter your 10-digit wireless phone  
number to access the SprintWeb home page.  
Chrome  
Use Chrome for Mobile to browse fast and sign in to bring your Chrome experience from your  
computer, anywhere you go.  
n
From home, tap  
Apps >  
Google >  
Chrome.  
Data Services General Information (Sprint  
Spark LTE and 3G Networks)  
The following topics will help you learn the basics of using your data services, including managing  
your user name, launching a data connection, and navigating the Web with your phone.  
Important: Certain data services requests may require additional time to process. While your  
phone is loading the requested service, the touchscreen or QWERTY keyboard may appear  
unresponsive when in fact they are functioning properly. Allow the phone some time to process your  
data usage request.  
Sprint Spark LTE  
The Sprint Spark enhanced LTE network provides your phone with wireless Internet access over  
greater distances than Wi-Fi and delivers data transfer rates of up to 60 Mbps. To connect your  
phone to Sprint Spark, you need to be in an area covered by the Sprint Spark enhanced LTE  
network.  
For more information about the availability of Sprint Spark in your location, visit sprint.com/coverage.  
Web and Data  
83  
         
Note: The availability and range of the network depends on a number of factors, including your  
distance to the base station and infrastructure and other objects through which the signal passes.  
Set Your Network Options  
1.  
From home, tap  
Apps >  
Settings >  
More networks > Mobile networks >  
Network mode.  
2. Select LTE/CDMA or Automatic. The phone will scan for the best available Sprint network and  
will automatically connect to it.  
When your phone is connected to the Sprint Spark enhanced LTE network, the  
Spark icon appears in the status bar.  
Sprint  
Note: The Sprint Spark network is self-discoverable, which means no additional steps are required  
for your phone to connect to it.  
Your User Name  
When you buy your phone and sign up for service, you’re automatically assigned a user name, which  
is typically based on your name and a number, followed by “@sprintpcs.com”. (For example, the  
third John Smith to sign up for Sprint data services might have [email protected] as his user  
name.)  
When you use data services, your user name is submitted to identify you to the Nationwide Sprint  
Network. Your user name is automatically programmed into your phone. You don’t have to enter it.  
Update Your User Name  
If you choose to change your user name and select a new one online, or make any changes to your  
services, you must then update the profile on your phone.  
1.  
From home, tap  
Apps >  
Settings >  
System Update.  
2. Tap Update Profile.  
Data Connection Status and Indicators  
Your phone displays the current status of your data connection through indicators at the top of the  
screen. The following symbols are used:  
Icon  
Description  
3G Coverage. The phone is connected to the Sprint 3G network.  
Web and Data  
84  
   
Icon  
Description  
3G network in use. The icon spins when your phone is scanning and connecting.  
Sprint Spark LTE Coverage: The phone is connected to the Sprint Spark enhanced  
LTE network. The icon spins when your phone is scanning and connecting.  
Hotspot  
Use the Hotspot feature to share your phone’s data connection with other devices via Wi-Fi.  
Important: Use of the Hotspot feature requires an additional subscription. Sign on to your account  
at sprint.com/mysprint or access your account via Sprint Zone (tap  
to learn more.  
Apps >  
Sprint Zone)  
Note: Turning on Hotspot on will disable your phone's connection to other Wi-Fi networks.  
Note: Using the Hotspot feature consumes battery power and uses data services.  
Turn Hotspot On or Off  
To conserve battery life, turn Hotspot on when you need it and turn it off when you’re finished. You  
can control Hotspot from Settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Hotspot, and then tap the ON/OFF switch beside Hotspot to turn Hotspot on or off.  
Connect a Device to Your Phone’s Hotspot  
When you connect a device to your phone’s Hotspot feature, the device can access your phone’s  
connection to the mobile data network.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Hotspot, and then tap the ON/OFF switch beside Hotspot to turn Hotspot on.  
3. On the other device, scan for Wi-Fi hotspots, and then select your phone’s hotspot.  
Your phone’s Network SSID will appear in the list of available devices. To find your phone’s  
l
Network SSID, go to  
of the screen.  
Settings > Hotspot. The network SSID is displayed near the top  
4. At the prompt, enter your phone’s password.  
Web and Data  
85  
 
l
Your phone uses WPA2 security, which requires a password. To find your phone’s  
password, go to  
instructions.  
Settings > Hotspot, and look for the password in the connection  
Virtual Private Networks (VPN)  
From your phone, you can add, set up, and manage virtual private networks (VPNs) that allow you  
to connect and access resources inside a secured local network, such as your corporate network.  
Prepare Your Phone for VPN Connection  
Depending on the type of VPN, you may be required to enter your login credentials or install security  
certificates before you can connect to your company’s local network. You can get this information  
from your network administrator.  
To connect to a VPN, you must have Mobile data enabled, or your phone must be connected to a  
Wi-Fi network. For information about setting up and using these connections on your phone, see  
Set a Screen Lock  
Before setting up a VPN, you must set a screen lock to prevent access to your phone by  
unauthorized users. A PIN or password screen lock provides sufficient security to set up trusted  
credential storage.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Lock screen > Screen lock.  
3. Choose a screen lock, either PIN or Password.  
4. Follow the prompts to configure the screen lock. For more information, see Screen Lock.  
Add a VPN  
Configure a connection to a VPN. You must have a PIN or Password screen lock set before adding  
a VPN.  
Tip: You may need to contact your network administrator for some of the information needed to set  
up a VPN connection.  
Web and Data  
86  
     
Add a Basic VPN  
1.  
2.  
3.  
From home, tap  
Apps >  
Settings.  
Tap  
More networks > VPN > Basic VPN.  
Tap  
Add to configure options:  
l
l
l
l
l
Name: Enter the name of the VPN.  
Type: Choose the type of VPN.  
Server address: Enter the address for the VPN server.  
PPP Encryption (MPPE): Tap to enable, if applicable for the VPN.  
Show advanced options:  
o
DNS Search domains  
o
DMS servers  
o
Forwarding routes  
4. Tap Save to save the VPN settings.  
Add an Advanced IPsec VPN  
1.  
2.  
3.  
From home, tap  
Apps >  
Settings.  
Tap  
More networks > VPN.  
Tap  
Add to configure options:  
l
l
l
l
l
l
VPN connection name: Enter the name of the VPN.  
IPsec connection type: Choose the type of VPN.  
Gateway: Enter the IP address or DNS name.  
Identity: Enter the Key ID.  
Pre-shared key: Enter the PSK.  
Show advanced options: Tap to set other options, depending on the type of VPN.  
o
Extended authentication  
o
Aggressive mode  
o
Perfect forward secrecy (PFS)  
Web and Data  
87  
o
o
o
o
o
o
Disable split tunneling  
Algorithm suite  
IKE groups  
IKE lifetime  
IPsec lifetime  
Connection attempt timeout  
4. Tap Save to save the VPN.  
Connect to a VPN  
Connect to a VPN that’s already set up on your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap More networks > VPN.  
3. In the VPNs section, tap a VPN.  
4. Follow the prompts to enter your login credentials, and connect. When you are connected, the  
VPN connected icon appears in the notification area of the title bar.  
Disconnect from a VPN  
The following describes how to disconnect from a VPN connection.  
1. Touch and hold the title bar, and then drag down to open the Notification panel.  
2. Tap the VPN connection to return to the VPN settings screen, and then tap the VPN connection  
to disconnect from it.  
When your phone has disconnected from the VPN, the VPN disconnected icon displays in the  
notification area of the title bar.  
Web and Data  
88  
   
Camera and Video  
Use your phone’s built-in camera and camcorder.  
Camera  
You can use the camera or camcorder to take and share pictures and videos.  
Open the Camera  
Follow the below procedure to access your phone’s camera.  
n
From home, tap  
Camera.  
n
n
Front/Back Camera: Switch between the front and back cameras.  
Customizable shortcuts: Shortcuts to favorite settings, which you can customize. The defaults  
shown here are Selective focus and HDR (Rich tone).  
n
n
n
n
n
Settings: Access camera settings.  
Mode Indicator: Shows the current Mode, which you can choose with Mode Selector.  
Record: Tap to start recording.  
Capture: Tap to take a picture.  
Mode Selector: Tap to choose a shooting mode. The current mode displays on the camera  
screen. Shooting modes allow you to choose modes for automatically adjusting settings to suit  
conditions, or to access special features like panorama or other specialty shots.  
n
Gallery: View your pictures or video, and access picture sharing and editing options.  
Camera and Video  
89  
     
Take a Picture  
You can take pictures with your phone’s front or back camera, or combine shots with Dual mode.  
1.  
From home, tap  
Camera.  
2. Using the phone’s screen as a viewfinder, compose your shot by aiming the camera at the  
subject. While composing your picture, use the onscreen options, or these gestures:  
l
Press the Volume key up or down to zoom in or out, or touch the screen with two fingers and  
pinch or spread them on the screen to zoom.  
l
Tap the screen to focus on the area you tapped.  
3.  
Tap  
Capture to take the picture.  
Note: To include your location in photos, turn on GPS tag in Settings.  
Record Videos  
In addition to taking pictures, you can record, view, and send videos with your phone’s built-in video  
camera.  
1.  
From home, tap  
Camera.  
2. Using the phone’s screen as a viewfinder, compose your shot by aiming the camera at the  
subject. While composing your shot, use the onscreen options, or these gestures:  
l
Press the Volume key up or down to zoom in or out, or touch the screen with two fingers and  
pinch or spread them on the screen to zoom.  
l
Tap the screen to focus on the area you tapped.  
3.  
Tap  
Record to begin recording. While recording, you can use these options:  
l
Tap the screen to change the focus area to the area you tapped.  
l
l
l
Tap  
Tap  
Tap  
Capture to take a still picture while continuing recording.  
Pause to temporarily stop recording.  
Stop to stop recording.  
Camera and Video  
90  
   
Review Pictures and Videos from the Camera  
After you take a picture or record a video, you can review and edit it right from the camera, using  
special Studio options.  
Review and Edit a Picture from the Camera  
1.  
From home, tap  
Camera.  
2. Take a picture, and then tap the Gallery thumbnail at the bottom right corner of the screen.  
3. While reviewing a picture, you can use these options:  
l
Screen mirroring: Choose a device to share the picture via Group Play.  
l
Share: Choose an option for sharing the picture. Options may include Dropbox,  
Bluetooth, Drive, Email, Flipboard, Gmail, Google+, Hangouts, Memo, Messages, Photos,  
Picasa, or Wi-Fi Direct.  
l
Studio: Edit the picture using the Studio tool. Options include:  
o
Adjustment: Rotate, crop, or resize the photo.  
o
Tone: Adjust the brightness, contrast, saturation, the red/green/blue color, the color  
temperature, or the Hue.  
o
Effect: Add an effect to the picture.  
o
Portrait: Adjust pictures of faces. You can remove redeye, brighten faces, airbrush, or  
adjust the focus on faces in the picture.  
l
l
Delete: Erase the current picture.  
Menu: Choose other options.  
Review and Edit a Video from the Camera  
1.  
From home, tap  
Camera.  
2. Record video, and then tap the Gallery thumbnail at the bottom right corner of the screen.  
3. While reviewing a video, you can use these options:  
l
Share: Choose an option for sharing the video. Options may include Dropbox,  
Bluetooth, Drive, Email, Flipboard, Gmail, Google+, Hangouts, Memo, Messages, Photos,  
Camera and Video  
91  
 
Picasa, or Wi-Fi Direct.  
l
Video trimmer: Edit the length of the video. Drag the trimmer from the end of the video  
(the right side of the screen), to shorten the video.  
l
l
Delete: Erase the current video.  
Menu: Choose other options.  
Configure the Camera  
Camera settings are special options that you can choose, right on the camera screen, to make taking  
pictures or recording videos easy, and to make your pictures or videos special.  
Customize Shortcuts  
The Camera screen offers two customizable shortcuts, to give you the ability to choose favorite  
settings on the fly.  
1.  
2.  
From home, tap  
Camera.  
Tap Settings, and then touch and drag settings to or from the two shortcuts.  
Choose a Shooting Mode  
Your phone’s camera offers many shooting modes, to make your pictures or videos special.  
1.  
2.  
From home, tap  
Camera.  
On the Camera screen, tap  
to choose a shooting mode. Scroll available modes, and then  
tap a mode to select it. Modes include:  
l
Auto: Automatically adjusts the exposure to optimize the color and brightness of pictures. In  
Auto mode, you can take single or burst shots (take burst shots by holding Capture to take  
multiple shots until you lift your finger).  
l
l
Beauty face: Automatically enhances facial features.  
Shot & more: Explore the various effects available for burst shots. You can apply effects  
right after taking the pictures, or in Studio.  
l
l
Panorama: Take multiple pictures to merge into one expansive picture. You can create a  
horizontal or vertical panorama picture.  
Virtual tour shot: Create an interactive virtual tour of your surroundings.  
Camera and Video  
92  
 
l
l
Dual camera: Take pictures and record videos using the front and rear cameras at the same  
time, to create a picture-in-picture shot. You can switch between the front and rear camera  
to control which picture appears in the smaller shot.  
Download: Browse and download additional modes to use with Camera. Read and accept  
the terms, and then browse for new modes.  
Choose Camera Settings  
1.  
2.  
From home, tap  
Camera.  
Tap  
Settings to configure options:  
l
Picture size: Choose a default size for the pictures you take.  
l
Burst shots: When on, you can take multiple pictures when you touch and hold the Capture  
button.  
l
l
Picture stabilization: When on, the Camera adjusts settings to minimize the effect of  
camera movement while shooting.  
Face detection: When on, the Camera will automatically adjust settings for taking pictures  
of faces.  
l
l
l
l
l
l
ISO: Set the sensitivity of the camera’s light meter.  
Metering modes: Choose how the Camera measures the light source.  
Tap to take pics: When on, you can tap the screen to take a picture.  
Selective focus: When on, you can choose areas of the screen to focus on.  
Video size: Choose a default size for videos.  
Recording mode: Choose a recording mode. You can choose to limit a video to a size that  
can be attached to a message, or record in slow, fast, or smooth motion.  
l
l
Video stabilization: When on, the Camera adjusts settings to minimize the effect of camera  
movement while recording.  
Audio zoom: While recording videos, zooming in on an object will amplify sound from that  
area and diminish other surrounding sound.  
l
l
l
l
Effects: Choose an effect to add to pictures.  
Flash: Choose a flash setting.  
Timer: Choose a timer setting to delay the taking of pictures or recording.  
HDR (Rich tone): When on, you can take pictures in various exposures and merge them to  
create pictures with rich color.  
l
Location tags: When on, GPS location information is stored in picture files.  
Camera and Video  
93  
l
l
l
Storage: If you have an optional memory card installed (not included), you can choose  
whether to save files to device memory or to the memory card.  
Review pics/videos: When on, pictures and videos display briefly after you take them so  
you can review them.  
Remote viewfinder: When turned on, you can take pictures using the viewfinder of a  
connected device. Your device and the remove device must be connected via Wi-Fi Direct  
connection to use this option.  
l
l
l
l
l
l
White balance: Choose a setting for current light conditions.  
Exposure value: Adjust the brightness of pictures.  
Guide lines: When on, guidelines display on the screen to aid in composition.  
Voice control: When on, you can take pictures or record videos by speaking commands.  
Help: Learn about using the Camera.  
Reset: Return settings to the defaults.  
Gallery  
Using the Gallery application, you can view pictures and watch videos that you’ve taken with your  
phone’s camera, downloaded, or copied to an optional memory card (not included).  
For pictures stored on an optional memory card, you can do basic editing such as rotating and  
cropping. You can also set a picture as your contact picture or wallpaper and share pictures with  
your friends.  
While viewing pictures in the Gallery, scroll up the screen to view more albums. Simply tap an album  
to view the photos or videos in that album.  
If you have pictures or videos stored on an optional memory card (not included), they will be display  
folders they are stored in, and folders are treated as albums. The actual folder names will be used as  
the album names. If you have downloaded any photos and videos, these will be placed in the All  
downloads album.  
Note: Tap  
More > Help to learn about Gallery.  
From home, tap Apps > Gallery.  
1.  
2. Select a folder location (such as Camera) and tap a thumbnail to view the picture or video.  
3. From the Gallery screen, you can use these options:  
l
Tap a picture or video to display it in full screen view.  
l
Touch and hold thumbnails to select them (indicated by a check mark).  
Camera and Video  
94  
 
l
Tap  
View by/Filter by to choose a display style. You can view by Time or Album, or  
Filter to show only scenery or documents.  
l
l
l
Tap  
Tap  
Tap  
Search to enter keywords to search for items, or choose a view or filter.  
Camera to launch the Camera to take pictures or record video.  
Menu for options. Available options depend on which gallery screen you are  
viewing, and may include:  
o
Select album/Select item: Depending on the view, tap albums or items to select them.  
After selection, you can tap Menu again for options you can use with the selected item.  
o
Delete: Erase item(s).  
o
Sort by oldest/Sort by latest: Choose how items are listed by time.  
o
Create album: Create a new album to group pictures.  
o
Content to display: Choose whether to display all content, or only pictures stored on  
your device, or from Dropbox, Facebook, or Picasa (if you have those accounts set up on  
your device).  
o
Slideshow: Choose options to create a slideshow for viewing your pictures and videos.  
o
Studio: Edit the item using the Studio tool.  
o
Settings: Configure Gallery settings. For more information, see Gallery Settings.  
o
Help: Learn about Gallery.  
Note: Available options depend on which gallery screen you are viewing. Additional options may  
include Content to display, Scan for nearby devices, and Show nearby devices.  
View Photos and Videos  
After selecting an album from the Albums tab, you can browse the photos and videos of that album in  
either photo pile or grid view. Tap a photo or video to view it in full screen.  
View Photos  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap a thumbnail to view the picture. While viewing a picture full-screen you can use these  
options:  
l
Screen mirroring: Choose a device to share the picture via AllShare or Group Play.  
Camera and Video  
95  
 
l
Share: Choose an option for sharing the picture. Options may include Group Play,  
Dropbox, Bluetooth, Email, Flipboard, Gmail, Google+, Hangouts, Messages, Picasa,  
Memo, or Wi-Fi Direct.  
l
l
Delete: Erase the current picture.  
Camera: Launch the Camera, to take pictures or record video.  
l
Menu: Choose other options, including:  
o
Edit: Modify the picture.  
o
More info: View information about the video.  
o
Copy to clipboard: Save a copy of the picture to the clipboard, so you can paste it into  
another app.  
o
Rotate left/Rotate right: Change the orientation of the picture.  
o
Crop: Adjust the size of the picture.  
o
Rename: Change the name of the video file.  
o
Slideshow: Create a slideshow.  
o
Set as: Set the picture as wallpaper on the lock or home screen.  
o
Print: Print the picture to a compatible Wi-Fi printer (not included).  
o
Settings: Configure Gallery settings.  
View Videos  
Note: If no icons are displayed on the screen in addition to the picture, tap anywhere on the screen  
to display them.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap a video to select it. When the video is displayed full-screen, you can use these options:  
l
Share: Choose an option for sharing the video. Options may include Bluetooth,  
Dropbox, Email, Gmail, Google+, Messages, Picasa, Wi-Fi Direct, or YouTube.  
l
Video trimmer: Edit the length of the video. Drag the trimmer from the end of the video  
(the right side of the screen), to shorten the video.  
l
Delete: Erase the current video.  
Camera and Video  
96  
l
l
Tap  
to play the video.  
Menu: Choose other options, including:  
More info: View information about the video.  
Rename: Change the name of the video file.  
Slideshow: Create a slideshow.  
o
o
o
o
Settings: Configure Gallery settings.  
Working with Photos  
You can touch and hold on a photo to open a selection menu and choose what to do with it. You can  
choose to delete the photo, rotate or crop it, and more.  
Rotate and Save a Photo  
To rotate or save your photo, follow the below procedures.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Select a folder location (such as Camera) and tap an image to view your picture.  
3.  
Tap  
Menu > Rotate left or Rotate right.  
The rotated picture is saved in your default storage location as a copy.  
Crop a Photo  
To crop your photos, follow the below procedures.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Select a folder location (such as Camera) and tap an image to view your picture.  
3.  
Tap  
Menu > Crop.  
4. To adjust the crop box size, touch and hold the edge of the box. When directional arrows appear,  
drag your finger inward to or outward to resize the crop box.  
5. To move the crop box to the part of the photo that you want to crop, drag the crop box to the  
desired position.  
6. Tap Done to apply the changes to the picture.  
The cropped picture is saved along with the original copy in your default storage location.  
Camera and Video  
97  
 
Share Photos and Videos  
You can share and send pictures and videos from your phone using several different methods,  
including messaging, email, social media apps, Bluetooth, cloud storage, and more. To share  
photos and videos, follow these procedures.  
Send Photos or Videos by Email  
You can send several photos, videos, or both in an email message. They are added as file  
attachments in your email.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the photos or videos you want to share.  
3. Tap the photos you want to send.  
4.  
5.  
Touch the screen and then tap  
Share > Gmail or Email.  
Send or Send.  
Compose your message and then tap  
Note: If you selected Email and you have multiple email accounts, the default email account will be  
used.  
Send a Photo or Video by Multimedia Message  
Although you can send several photos or videos in a multimedia message, it may be better to send  
one at a time, especially if the files are large in size.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the photos or videos you want to send.  
3. Tap the photo or video you want to send.  
4.  
5.  
Touch the screen and then tap  
Share > Messages.  
Send.  
Compose your message and then tap  
Send Photos or Videos Using Bluetooth  
You can select several photos, videos, or both and send them to someone’s phone or your computer  
using Bluetooth.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the photos or videos you want to send.  
Camera and Video  
98  
   
3. Select the photos or videos you want to send.  
4.  
Touch the screen and then tap  
Share > Bluetooth.  
In the next few steps, you’ll be asked to turn on Bluetooth on your phone and connect to the receiving  
Bluetooth phone so the files can be sent. For more information, see Bluetooth.  
Share Photos or Videos on Google+  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the photos or videos you want to send.  
3. Tap the photo or video you want to send.  
4.  
5.  
Touch the screen and then tap  
Share > Google+.  
Compose your message and then tap  
.
Share Photos on Picasa  
You need to be signed in to a Google Account to upload pictures to the Picasa photo organizing  
service.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the photos or videos you want to share.  
3. Select the photos you want to share.  
4.  
Touch the screen and then tap  
Share > Picasa.  
5. Select the online album where you want to upload the pictures.  
6. Tap Upload. You can view the photos online at picasaweb.google.com.  
Share Videos on YouTube  
You can share your videos by uploading them to YouTube. Before you do this, you must create a  
YouTube account and sign in to that account on your phone.  
1.  
From home, tap  
Apps >  
Gallery.  
2. Tap the album that contains the videos you want to share.  
3. Select the video you want to share.  
4.  
Touch the screen and then tap  
Share > YouTube.  
Camera and Video  
99  
     
5. Enter the prompted information, such as description and tags, and select a privacy option.  
6. Tap Upload.  
Photos  
Keep all your photos backed up and organized with Google+ Photos.  
n
Google >  
Photos.  
Video  
Play videos stored on your phone, or from your other devices (you must sign in to your Samsung  
account to play videos synced from your other devices).  
1.  
From home, tap  
Apps >  
Video.  
2. Scroll through the videos stored on your device. After a few seconds, each video thumbnail  
begins playing a preview of the clip.  
3. Tap a video to view it.  
Use Pop-up Play  
Multitask with Pop-up Play - transform your video player into a pop-up window floating on the  
screen. The video will continue to play, and the pop-up window can be resized or moved anywhere  
on the screen.  
1.  
From home, tap  
Apps >  
Video.  
2. Tap a video to view it.  
3.  
Tap  
to continue playing the video in a floating window. Drag the window to any location on  
the screen, and use two fingers to pinch or spread to resize the floating window.  
Camera and Video  
100  
   
Tools and Calendar  
Learn how to use many of your phone’s productivity-enhancing apps and features.  
Bluetooth  
Bluetooth is a short-range communications technology that allows you to connect wirelessly to a  
number of Bluetooth phones, such as headsets and hands-free car kits, and Bluetooth-enabled  
handhelds, computers, printers, and wireless phones. The Bluetooth communication range is  
usually approximately 30 feet.  
Turn Bluetooth On or Off  
When Bluetooth is on, you can scan and find other Bluetooth devices, to share information between  
the devices. Turn Bluetooth off when not in use to conserve battery power.  
1.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
2. Tap the ON/OFF switch to turn Bluetooth on or off.  
Note: You can also turn Bluetooth on or off from the Notification panel. Drag down from the top of  
the screen, and then tap Bluetooth.  
Note: for Bluetooth settings information see Bluetooth Settings.  
Connect a Bluetooth Headset or Car Kit  
You can listen to music over a Bluetooth stereo headset, or have hands-free conversations using a  
compatible Bluetooth headset or car kit. It’s the same procedure to set up stereo audio and hands-  
free devices.  
To listen to music with your headset or car kit, the headset or car kit must support the A2DP  
Bluetooth profile.  
1.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
2. Tap the ON/OFF switch to turn Bluetooth on.  
3. Make sure that the target device is discoverable, so that your phone can find it. Refer to the  
instructions that came with the device to find out how to set it to discoverable mode.  
4. Tap Scan. Your phone will start to scan for Bluetooth devices within range.  
Tools and Calendar  
101  
       
5. When you see the name of the target device displayed in the Bluetooth devices section, tap the  
name. Your phone then automatically tries to pair with the target device.  
6. If automatic pairing fails, enter the passcode supplied with the target device.  
The pairing and connection status is displayed below the hands-free headset or car kit name in the  
Bluetooth devices section. When the Bluetooth headset or car kit is connected to your phone,  
(Bluetooth connected) displays in the status bar. Depending on the type of headset or car kit you  
have connected, you can then start using the headset or car kit to listen to music or make and receive  
phone calls.  
Note: Due to different specifications and features of other Bluetooth-compatible devices, display  
and operations may be different, and functions such as transfer or exchange may not be possible  
with all Bluetooth-compatible devices.  
Reconnect a Headset or Car Kit  
When you have paired a headset with your phone, you should be able to reconnect it automatically  
by turning on Bluetooth on your phone and then turning on the headset. However, sometimes you  
will need to reconnect manually, for example if you have been using your headset with another  
Bluetooth device.  
1.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
2. Tap the ON/OFF switch to turn Bluetooth on.  
3. Make sure that the target device has Bluetooth turned on.  
4. Tap the target device’s name in the Bluetooth devices section.  
5. If prompted to enter a passcode, try 0000 or 1234, or consult the target device’s documentation  
to find the passcode.  
Tip: If you still cannot reconnect to the target device, follow the instructions in Disconnect or Unpair  
From a Bluetooth Device, and then follow the instructions in Connect a Bluetooth Headset or Car  
Kit.  
Disconnect or Unpair from a Bluetooth Device  
Follow these instructions to disconnect or unpair your phone from a Bluetooth device.  
Disconnect from a Bluetooth Device  
You can disconnect from a Bluetooth device, without removing the pairing relationship between the  
devices.  
Tools and Calendar  
102  
   
1.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
2. Tap the device name, and then tap OK.  
Unpair from a Bluetooth Device  
You can make your phone forget its pairing connection with another Bluetooth device. To connect to  
the device again, you will need to pair with it again.  
1.  
2.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
In the Bluetooth devices section, tap  
beside the device name, and then tap Unpair.  
Send Information Using Bluetooth  
You can use Bluetooth to transfer information between your phone and another Bluetooth-enabled  
device such as a phone or notebook computer. The first time you transfer information between your  
phone and another device, you need to enter or confirm a security passcode. After that, your phone  
and the other device are paired, and you will not need to exchange passcodes to transfer information  
in the future.  
You can send the following types of information, depending on the device you are sending to:  
n
n
n
n
Images and videos  
Calendar events  
Contacts  
Audio files  
Send Information from Your Phone to Another Device  
Follow the steps below to transfer information from your phone to another device.  
1. Set the receiving device to discoverable mode. You may also need to set it to “Receive Beams”  
or “Receive Files”. Refer to the device’s documentation for instructions on receiving information  
over Bluetooth.  
2. On the phone, open the application that contains the information or file you want to send. Follow  
the steps for the type of item you want to send:  
l
Photo or video (in Camera). After capturing a photo, on the preview screen, tap  
>
Bluetooth.  
l
Photos and videos (in Gallery). Tap a picture or video, and then tap  
> Bluetooth.  
Tools and Calendar  
103  
   
Tip: If your phone remembers Bluetooth as a previous selection within the Camera or Gallery, you  
can tap  
(to the right of the  
icon).  
l
Calendar event: In the Calendar’s Day view, Agenda view, or Week view, tap the event and  
then tap  
> Share via > Bluetooth.  
l
l
Music. While playing a song in the Music app, tap  
Voice recording. On the main Voice Recorder screen, touch and hold a recording and then  
tap > Bluetooth.  
Menu > Listen via Bluetooth.  
3. If you are prompted to turn on Bluetooth, tap Yes.  
4. Tap the name of the receiving device.  
5. If prompted, accept the connection on the receiving phone, and enter the same passcode on  
both your phone and the other device, or confirm the auto-generated passcode.  
6. On the receiving device, accept the file.  
Receive Information Using Bluetooth  
Your phone is capable of receiving a wide variety of file types with Bluetooth, including photos, music  
tracks, and documents such as PDFs.  
1.  
From home, tap  
Apps >  
Settings >  
Bluetooth.  
2. If Bluetooth is not on, tap the ON/OFF switch to turn it on.  
3. Tap the check box beside your phone's Bluetooth name to make it discoverable.  
4. On the sending device, send one or more files to your phone. Refer to the device’s  
documentation for instructions on sending information over Bluetooth.  
5. If prompted, enter the same passcode on both your phone and the other device, or confirm the  
auto-generated passcode. A Bluetooth authorization request is displayed on your phone.  
6. When your phone receives a file transfer request notification, tap Accept.  
7. When the file is transferred, a notification displays. To open the file immediately, slide down the  
Notification panel, and then tap the relevant notification.  
When you open a received file, what happens next depends on the file type:  
n
n
Media files and documents are usually opened directly in a compatible application. For example,  
if you open a music track, it starts playing in the Music application.  
For a vCalendar file, select the calendar where you want to save the event, and then tap Import.  
Tools and Calendar  
104  
 
n
n
The vCalendar is added to your Calendar events. (For more information on using the Calendar,  
see Calendar.)  
For a vCard contact file, if there are multiple vCard files on your storage card, you can choose to  
import one, several, or all of those contacts to your contacts list.  
Calendar  
Use Calendar to create and manage events, meetings, and appointments. Your Calendar helps  
organize your time and reminds you of important events. Depending on your synchronization  
settings, your phone’s Calendar stays in sync with your Calendar on the Web, Exchange ActiveSync  
calendar, and Outlook calendar.  
Note: For information about Calendar options, see Calendar Settings.  
Add an Event to the Calendar  
Add events to your Calendar to help you organize your time and remind you of important events.  
Note: To synchronize calendar events among your Google and Corporate accounts, make sure  
they are being managed by your phone. See Accounts and Messaging for more information.  
1.  
From home, tap  
Apps >  
Calendar.  
2. Double-tap a day to which you would like to add an event to reveal the Add event/Add task  
screen.  
3. If you have accounts set up on your phone, you can assign the new event to an account by  
tapping the Calendar field and then selecting an account.  
l
l
l
l
My calendar: Calendar entries that are stored locally on the phone and not part of an  
account.  
Samsung Calendar: Calendar entries that are synchronized between your phone and your  
Samsung account.  
Google/Gmail: Calendar entries that are synchronized between your phone and your  
Google account.  
Microsoft Exchange ActiveSync: Calendar entries that are synchronized between your  
phone and a Microsoft Exchange ActiveSync account.  
4. Enter information about the event:  
l
Tap the Title field and enter a title for the event.  
l
Tap the Location field to enter a location for the event in the Location field or tap the icon to  
select the location on the a map.  
Tools and Calendar  
105  
   
l
Select a Start and End date and time for the event by tapping the corresponding fields, and  
adjusting the month, day, and year. Tap the All day field to set this as an all-day event. If set  
as an all-day event, the time fields are removed.  
5. Tap Save, or tap View more options to enter more information about the event. Available  
options depend on the type of event, and the account it’s assigned to:  
l
l
l
Select an alarm time by tapping the Reminder field.  
Enter participants in the Participants field.  
Tap Show me as to choose how the event shows on your calendar to other event  
organizers.  
l
Tap Privacy to select who is allowed to see this event. Private allows only the participants to  
see the event. Public allows anyone with access to your calendar to see the event.  
l
l
l
l
Select a recurrence cycle for the event by tapping the Repeat field.  
Enter a description for the event in the Description field.  
Tap a sticker to add an sticker to the event.  
Tap the Time zone to adjust the time zone.  
6. Tap Save to store the new event and synchronize it with your selected account.  
Event Alerts  
When your phone is turned on and you have an event alarm scheduled, your phone alerts you and  
displays the event summary. There are several ways your phone alerts you to scheduled events:  
n
n
By playing the assigned ringtone.  
By showing the Alert screen.  
Event Reminders  
When your phone is turned on and you have an event alarm scheduled, there are several ways your  
phone alerts you to scheduled events:  
n
By playing a short beep.  
n
By indicating an icon within the Status bar.  
To view additional options:  
1. Tap the Status bar, and then slide your finger down the screen to open the Notification panel.  
2. Tap the upcoming event name from the onscreen list to display the event within the Calendar  
notifications screen.  
3. Tap an option.  
Tools and Calendar  
106  
 
l
Set snooze duration to set the length of time to allow before you are reminded of the event.  
Choose from: 3 minutes, 5 minutes, 10 minutes, 15 minutes, or 30 minutes.  
l
l
Snooze to be reminded of the event at a future time.  
Dismiss to dismiss the reminder.  
View Events  
The following procedure helps you view your calendar events.  
1.  
2.  
From home, tap  
Apps >  
Calendar.  
To view a Calendar event farther out, tap  
, and then tap Week or Month.  
3. Tap the day for which you would like to view events.  
4. To display an event’s details, tap it from the current screen.  
Day and Agenda Views  
Day view displays a list of the events of one day.  
Agenda view shows a list of events in chronological order.  
The color bars on the left side of the events indicate the type of calendar that includes the event.  
When in Day view, slide left or right across the screen to view earlier or later days.  
Month and Agenda View  
Month and Agenda view shows the month, with a list of events for the month below.  
While in Month and agenda view:  
n
n
n
You can touch and hold on a day to create a new event on that day.  
Tap an event to view its details.  
Slide left or right across the screen to view earlier or later months.  
Week View  
Week view displays a chart of the events of one week.  
When in Week view:  
n
n
n
You can touch and hold on a time slot to create a new event at that time.  
Tap an event to view its details.  
Slide left or right across the screen to view earlier or later weeks.  
Tools and Calendar  
107  
 
Year and Month Views  
In Year or Month view, you’ll see markers on days that have events.  
When in Year or Month view:  
n
n
n
Tap a day to view the events of that day.  
Touch and hold a day to create a new event on that day.  
Slide left or right to view earlier or later months or years.  
Erase Events  
The following procedures show you how to erase your calendar events.  
1.  
From home, tap  
Apps >  
Calendar.  
2. Open the calendar event details:  
l
l
In Agenda, Day, and Week views, tap the calendar event you want to delete.  
In Month view, tap the date where the calendar event occurs, and then tap the calendar  
event.  
l
In Year view, tap the month in which the event is located.  
3.  
Tap the event, and then tap  
Delete.  
4. In the Delete confirmation box, tap OK.  
– or –  
If the calendar event is recurring, select Only this event, This and future events, or All  
events in series, and tap OK.  
Calculator  
Use the Calculator app to perform mathematical calculations.  
Note: Rotate the phone to switch to a scientific calculator, for advanced calculator functions.  
1.  
From home, tap  
Apps >  
Calculator.  
2. Tap the keypad to enter your equation. You can touch and hold C to clear all numbers.  
Tools and Calendar  
108  
   
Clock  
The Clock app offers features for keeping track of time and setting alarms.  
1.  
From home, tap  
Apps >  
Clock.  
2. Tap a tab to use a feature:  
l
l
Alarm: This feature allows you to set an alarm to ring at a specific time.  
World clock: allows you to view the time of day or night in other parts of the world. World  
Clock displays time in hundreds of different cities, within all 24 time zones around the world.  
l
l
Stopwatch: You can use this option to measure intervals of time.  
Timer: You can use this option to set a countdown timer. Use a timer to count down to an  
event based on a preset time length (hours, minutes, and seconds).  
Create an Alarm  
Create an alarm event. You can set one-time or recurring alarms, and choose options for how to be  
notified for the alarm.  
1.  
2.  
From home, tap  
Apps >  
Clock.  
Tap  
Create alarm, and then enter information for the alarm. Alarm options include:  
l
l
l
l
Time: Choose a time for the alarm.  
Days: Choose the days to use this alarm.  
Repeat weekly: When enabled, the alarm will repeat every week on the selected days.  
Alarm type: Choose whether the alarm will use sound, vibration, or vibration and sound to  
alert you.  
l
l
l
Alarm tone: If you have chosen an alarm type that includes sound, choose a sound to play  
for the alarm.  
Volume: If you have chosen an alarm type that includes sound , drag the slider to set the  
volume of the alarm.  
Smart alarm: When on, the alarm will start playing a tone at a low volume at an interval  
before the alarm time, and slowly increase in volume. Choose a time interval and a tone to  
use with smart alarm. Available when you have chosen an alarm type that includes sound.  
l
Name: Enter a name for the alarm.  
3. Tap Save.  
Tools and Calendar  
109  
 
Delete an Alarm  
1.  
2.  
From home, tap  
Apps >  
Clock.  
Touch and hold an alarm, and then tap  
Delete.  
Drive  
With the Google Drive application, everything that you add to your Drive from work or home is also  
available on your device. You can create and edit documents on your device and the changes are  
saved everywhere.  
For more information, visit google.com/drive/.  
Note: You’ll need to set up your Google account on your phone to use Drive.  
n
From home, tap  
Google >  
Drive .  
Dropbox  
Dropbox works to provide access to your desktop files directly from your phone. This applications  
allows you to bring your files with you when you're on the go, edit files in your Dropbox from your  
phone, upload photos and videos to Dropbox, and share your selected files freely with family and  
friends.  
The in-phone application works in conjunction with a partner program placed on a target computer  
using an active Internet connection.  
Dropbox creates a folder that automatically synchronizes its contents across all of your connected  
devices on your account. Update a file to your Dropbox on your computer, and it’s automatically  
updated to the same folder on your other devices.  
Download the Desktop Application  
Follow the procedures below to download the desktop application.  
1. Use your computer’s browser to navigate to: dropbox.com/.  
2. Follow the onscreen setup and installation instructions on your target computer containing the  
desired files.  
Important: The computer application must be installed on the computer containing the desired files.  
This computer must have an active Internet connection.  
Tools and Calendar  
110  
     
Note: The Dropbox service offers 2GB of free “Cloud” storage.  
Accessing Dropbox on Your Device  
Follow the procedures below to access the Dropbox app.  
1.  
From home, tap  
Apps >  
Dropbox.  
2. Tap Sign in, and then enter your current account credentials, to sign in to your Dropbox  
account.  
– or –  
Swipe through the information screens, tap Sign up, and then follow the onscreen instructions  
to register for a new account.  
Manually Uploading a Picture to Dropbox  
Follow the below procedures to manually upload pictures to the Dropbox app.  
1.  
From home, tap  
Apps >  
Camera.  
2. After you take a picture, tap Gallery to preview the current image.  
3. Tap the image to reveal the image options at the top of the screen.  
4.  
Tap  
> Add to Dropbox, select a folder location, and tap Add.  
Note: If your share folder is located on your computer, you will momentarily receive an onscreen  
popup notifying you that a new image was uploaded to your shared Dropbox folder.  
Flipboard  
Use Flipboard to create a personalized digital “magazine” out of everything being shared with you.  
Access news stories, personal feeds and other related material. Flip through your Facebook  
newsfeed, tweets from your Twitter account, photos from friends and much more.  
n
From home, tap  
Apps >  
Flipboard.  
Google Now  
Google Now gets you just the right information at just the right time.  
Tools and Calendar  
111  
       
It tells you today’s weather before you start your day, how much traffic to expect before you leave for  
work, when the next train will arrive as you’re standing on the platform, or your favorite team's score  
while they’re playing. And the best part? All of this happens automatically. Cards appear throughout  
the day at the moment you need them.  
For more information, visit google.com/now.  
1.  
Press and hold  
Home.  
2. Follow the prompts to learn about Google Now, and set up your preferences.  
Google Search  
Use Google Search to search the Internet.  
n
From home, tap  
Apps >  
Google.  
Help  
Help provides information to help with your phone questions.  
n
From home, tap  
Apps >  
Help.  
Lookout Security  
Lookout Security™ provides mobile device-specific security features that are coupled with a minimal  
performance hit. Lookout Mobile Security provides key security options that are unique to the mobile  
market. Along with the antivirus and anti-malware tech, there's a lost and stolen phone locator  
service, an application privacy adviser, and a backup service.  
n
From home, tap  
Apps >  
Lookout Security.  
Lumen Toolbar  
The Lumen Toolbar, available to Sprint Customers, enables an extensive array of new browser  
extensions that enhance user experience – from contextual recommendations to App discovery to  
social applications and browser utilities. With one-click access to News Feeds and one-click sharing  
of content via Facebook™, Twitter™ and other networks, along with community- and friend-based  
recommendations.  
Tools and Calendar  
112  
       
1.  
From home, tap  
Apps >  
Lumen Toolbar.  
2. Tap Settings and select your Lumen Toolbar options.  
Memo  
The Memo application allows you to write memos that can include text, audio, and images.  
1.  
From home, tap  
Apps >  
Memo.  
2. In Memo, you can use these options:  
l
Tap  
Tap  
Tap  
Add to create a new memo.  
l
l
l
Options for available Memo categories or Manage categories.  
Search to enter key words to find a memo.  
Tap  
Menu and select one of the following options:  
o
Select: Choose memo(s), to delete them or for other options like sharing or printing.  
Delete: Select memo(s) to erase.  
o
o
Account: Access your Samsung account, to sync memos with your account.  
My Files  
My files allows you to manage your manage your sounds, images, videos, Bluetooth files, Android  
files, and other memory card data in one convenient location. This application allows you to launch a  
file if the associated application is already on your phone.  
1.  
From home, tap  
Apps >  
My files.  
2. Folders display, including:  
l
All files: Tap to choose Device storage, or SD memory card, to show files stored in the  
phone’s internal memory, or on an optional installed memory card (not included).  
l
l
l
Images: Pictures stored on your phone.  
Videos: Videos stored on your phone.  
Audio: Songs stored on your phone.  
Tools and Calendar  
113  
   
l
l
Documents: Other files stored on your phone.  
Downloaded apps: Apps you’ve downloaded and installed.  
Note: Different folders may appear depending on how your phone is configured.  
My Magazine  
Find content, information and apps, recommended for you, all in one place.  
You can enable location services for personalized results based on your results. For more  
information about location services, see Location Settings.  
To launch My Magazine:  
n
From home, scroll to the far-right home screen.  
Polaris Office 5  
®
®
Polaris Office Mobile for Android is a Microsoft Office compatible office suite. This application  
provides a central place for managing your documents online or offline.  
Polaris Office lets you open, create, and edit Word documents, PowerPoint presentations, Excel  
®
spreadsheets, and text files. Polaris Office can also open Adobe PDF (Portable Document Format)  
files.  
®
n
From home, tap  
Apps >  
POLARIS Office 5.  
S Health  
S Health™ is a wellness application that can help you manage your health. Set fitness goals, check  
your progress, and keep track of your overall health.  
1.  
From home, tap  
Apps >  
S Health.  
2. Follow the prompts to get started:  
l
l
l
Read the introduction and tap Start.  
Read and agree to the terms and conditions, and then tap Next.  
Sign in to your Samsung account if you have not already done so. For more information,  
refer to Samsung Account. You must sign in to a Samsung account to set and save goals,  
and use other advanced S Health features.  
l
Follow the onscreen instructions to enter information about yourself, and then tap Start.  
Tools and Calendar  
114  
     
3. Use S Health to track your health activities:  
l
l
l
l
Pedometer: Count the number of steps you take. Tap Start to start counting. You can  
pause counting and then tap Start to begin again. If you signed in to your Samsung account,  
you can set goals, track your progress, and share your results.  
Exercise: Set and manage exercise goals, and track your progress. You can track activities  
by type, such as running, walking, cycling, and hiking. S Health also offers access to the  
Music app, to work out to your favorite songs.  
Heart rate: Measure your heart rate, using the heart rate sensor on the back of your phone  
(next to the Camera flash). Place your finger over the sensor, and then tap the screen to  
start. Hold your finger on the sensor, and keep still until the sensor reports your heart rate.  
Food intake: Track your daily food intake, by entering your meals and snacks. You can keep  
track of your favorite foods, and take pictures of your meals.  
Note: Tap  
Menu > Help for more detailed information.  
Before You Start Exercising  
This app can be used to monitor your exercise. While moderate physical activity, such as brisk  
walking, is safe for most people, health experts suggest that you talk with your doctor before you  
start an exercise program, particularly if you have any of the following conditions:  
n
n
n
n
Heart disease;  
Asthma or lung disease;  
Diabetes, or liver or kidney disease;  
Arthritis.  
You should also check with your doctor if you have symptoms suggestive of heart, lung, or other  
serious disease, such as:  
n
n
n
n
n
n
Pain or discomfort in your chest, neck, jaw, or arms during physical activity;  
Dizziness or loss of consciousness;  
Shortness of breath with mild exertion or at rest, or when lying down or going to bed;  
Ankle swelling, especially at night;  
A heart murmur or a rapid or pronounced heartbeat;  
Muscle pain when walking upstairs or up a hill that goes away when you rest.  
Finally, the American College of Sports Medicine recommends that you see your doctor before  
engaging in vigorous exercise if two or more of the following apply:  
n
You are a man older than age 45 or a woman older than age 55;  
You have a family history of heart disease before age 55;  
n
Tools and Calendar  
115  
n
n
n
n
n
You smoke or quit smoking in the past six months;  
You have not exercised for three months or more;  
You are overweight or obese;  
You have high blood pressure or high cholesterol;  
You have impaired glucose tolerance, also called pre-diabetes.  
When in Doubt - Check it Out  
If you are unsure of your health status, have several health problems, or are pregnant, you should  
speak with your doctor before starting a new exercise program. Working with your doctor ahead of  
time is a good way to plan an exercise program that is right and safe for you. Consider it the first step  
on your path to physical fitness.  
S Voice  
S Voice™ is a voice recognition application you can use to activate a wide variety of functions on  
your phone.  
This is a natural language recognition application. You can ask questions (Is it raining in Dallas?) or  
speak commands (Show me where to find cheap gas).  
1.  
From home, tap  
Apps >  
S Voice.  
2. Follow the prompts to learn about S Voice, and to review and accept the terms and conditions.  
3. Tap Tutorial to learn about S Voice, or tap Start S Voice to skip the tutorial and start using  
S Voice.  
4. Speak a command. The screen gives you some examples.  
5. Tap the microphone icon if the phone does not hear you, or to give it a command.  
Configure S Voice  
Configure options for interacting with your phone with S Voice.  
You can access S Voice settings in two ways:  
n
From S Voice: From home, tap  
Apps >  
S Voice >  
Menu > Settings.  
n
From Settings: From home, tap  
S Voice >  
Menu > Settings.  
For details about S Voice settings, see S Voice Settings.  
Tools and Calendar  
116  
 
Smart Remote  
Use your phone to control your TV, Set-top box, DVR, Stereos, and other electronic devices.  
Configure Smart Remote  
Choose your TV service and personalize your selections.  
1.  
From home, tap  
Apps >  
Smart Remote.  
2. Follow the prompts to configure the service:  
l
l
Find your TV service: Follow the prompts to select your country or region, enter your ZIP  
code, and then select your TV service provider from the list.  
Personalize: Smart Remote offers Just For You suggestions based on what you like to  
watch. Personalize your top picks by answering a few questions, and then tap the star on  
shows you like. Smart Remote will suggest similar programs. You can skip personalization  
and continue with configuration.  
3. Continue following the prompts to read and agree to the disclaimer and complete configuration.  
Customize Your Smart Remote  
Set up your phone to control your TV, Set-top box, DVR, Stereos, and other electronic devices.  
Note: Your TV or other device must be turned off to customize Smart Remote.  
Set Up Your Smart Remote to Control Your TV  
1.  
2.  
From home, tap  
Apps >  
Smart Remote.  
Tap Universal Remote Control > Continue.  
3. Tap to select your TV brand.  
l
If your TV is not listed, tap Show other brands to choose from a full list of brands.  
l
If you are using a projector, tap I have a home projector, and then choose the brand of  
projector.  
4.  
Aim your phone at the TV, and then tap  
Power to turn on your TV. Be sure the Infrared  
Transmitter on the top of your phone is pointed at the TV.  
5. Confirm the codes:  
Tools and Calendar  
117  
     
l
l
If the TV turned on, tap Yes, this code 1 works.  
If the TV did not turn on, tap No, text next code 2, or Send this code 1 again. Depending  
on the model of your TV, you may need to try several codes to find the one that works.  
6. From the Select your channel source screen, select the entry that matches your current method  
for changing channels:  
l
Set-top Box: Choose this if you use a set-top box from your TV service provider to change  
channels. Continue to choose the brand of your set-top box, and then tap Enable IR to  
configure your set-top box to receive commands from your phone’s Infrared Transmitter.  
l
My xxx TV: Choose this when your TV signal is fed directly into the TV, and you currently  
use your TV remote to change channels.  
Use Your Smart Remote to Control Your TV  
After customizing Smart Remote, you can use it to control your TV.  
1.  
2.  
From home, tap  
Apps >  
Smart Remote.  
From the Smart Remote screen, tap  
Universal Remote Control for options:  
l
l
Easy remote: provides the most common used control features. Scroll down to view  
additional functions.  
In a single motion touch and drag up from the bottom right of the screen to access additional  
remote options, including:  
o
TV: Control functions for your TV.  
o
[Set top box]: Control your set-top box.  
Voice Recorder  
The Voice recorder allows you to record an audio file up to one minute long and then immediately  
share it. Recording time will vary based on the available memory within the phone.  
Make a Voice Recording  
1.  
From home, tap  
Apps >  
Voice Recorder.  
2. Use the Voice Recorder controls:  
l
To start recording, tap  
Record and speak into the microphone.  
Tools and Calendar  
118  
   
l
l
l
To pause recording, tap  
Pause. To end the recording, tap  
Stop.  
To cancel the recording, tap  
Cancel.  
To mark a spot in the recording so you can find it later, tap  
Bookmark.  
Share a Voice Recording  
1.  
From home, tap  
Apps >  
Voice Recorder.  
2.  
3.  
Tap  
Tap  
List, and then touch and hold on a recording to display options.  
Share, and then follow the prompts to choose a method and share the file.  
Modify a Voice Recording  
1.  
2.  
3.  
From home, tap  
Apps >  
Voice Recorder.  
Tap  
List, and then touch and hold on a recording to select it.  
Tap  
Menu to display options:  
l
Change category: You can use categories to organize voice recordings. Choose a  
category, or tap Add category to create a new one.  
l
l
Rename: Change the name of the voice recording.  
Set as: Use the recording as the default Device ringtone, as a Caller ringtone, or as an  
Alarm tone.  
l
l
Write to Voice Label: You can save the voice recording to a Voice Label via NFC.  
Details: View information about the voice recording.  
Voice Recorder Options  
1.  
2.  
From home, tap  
Apps >  
Voice Recorder.  
Tap  
List to view a list of recordings. While viewing the list, you can use these options:  
Search: Enter keywords to search for a recording.  
Delete: Erase recording(s).  
l
l
l
Close: Return to the recording screen.  
Tools and Calendar  
119  
l
Select mode: Choose a recording mode to match the type of voice recording.  
3.  
Tap  
Menu for options:  
l
Select: Choose voice recording(s). After selection, you can Share or Delete the selected  
recordings, or use other Menu options.  
l
l
Sort by: Choose an order to display the list.  
Filter by category: Choose a category, to display only voice recordings assigned to that  
category.  
l
l
Edit categories: Enter and manage a list of categories you can use to organize voice  
recordings.  
Settings: the following settings are available:  
o
Save to: If you have an optional memory card installed (not included), you can choose  
whether your recordings will be saved to device memory, or to the card.  
o
Recording quality: Set the recording quality to High or Normal.  
o
Recording volume: Choose the default volume for recordings.  
o
Contextual filename: Choose whether the phone automatically creates a filename that  
includes location information, when the Location tags option is enabled (below).  
o
Default file name: Choose the name prefix for your recordings. For example, if your  
Default name is Voice, your recordings would be named Voice 001, Voice 002, Voice  
003, etc.  
o
Noise reduction: Choose whether the phone uses noise reduction during recording, to  
improve recording quality.  
o
Display logo: When turned on, you can choose to have an image display on the screen  
during recording. Tap the ON/OFF switch to turn the option on, and then choose an  
image.  
o
Location tags: When enabled, location information will be saved in recording files.  
o
Language: Choose a language.  
o
Skip interval: Choose the number of seconds to skip when you touch the Forward and  
Back buttons during playback.  
Voice Search  
Use Google Voice Search to search the Web by speaking commands.  
Tools and Calendar  
120  
 
1.  
From home, tap  
Apps >  
Voice Search.  
2. When the Google Voice Search screen displays, say “OK Google” or tap the microphone icon,  
and then speak your command.  
3. Scroll down the Voice Search screen to learn about using Voice Search and hear examples,  
including:  
l
l
l
l
l
l
l
l
l
Make phone calls  
Get directions  
Send messages  
Set reminders  
Ask questions  
Schedule meetings  
Play music & movies  
Set alarms  
Try more voice actions  
microSD Card  
A microSD™ memory card is an optional accessory (not included) that allows you to store images,  
videos, music, documents, and other data on your phone.  
Important: You can damage a microSD card by improper installation. Please be careful when  
inserting, removing, or handling it.  
Install a microSD Card  
Follow the instructions below to install an optional memory card (not included).  
1. Using the slot provided, gently lift the cover off the phone.  
2. With the gold contacts facing down, slide the card into the slot. Note that the microSD card slot is  
on top of the SIM card, which holds information about your phone and service, and should  
remain installed.  
Tools and Calendar  
121  
   
3. Replace the battery compartment cover, making sure all the tabs are secure and there are no  
gaps around the cover.  
Important: Ensure that the back cover and the multipurpose jack cover are closed tightly to prevent  
water and dust entering the device. Open or loose covers may allow water and dust to enter the  
device and cause damage.  
Remove a microSD Card  
Use the following procedure to remove an optional microSD card from your phone.  
Important: Before removing an optional installed microSD card, you must unmount the card first to  
prevent corrupting the data stored on it or damaging the card. For more information, see Unmount a  
microSD Card.  
1. Using the slot provided, gently lift the cover off the phone.  
2. Carefully slide the card out of the slot.  
3. Replace the battery compartment cover, making sure all the tabs are secure and there are no  
gaps around the cover.  
View microSD Card Memory  
Use the following procedure to view memory usage information for an optional installed microSD  
card (not included).  
n
From home, tap  
Apps >  
Settings >  
Storage. (The total and available memory  
space will be displayed.)  
Format a microSD Card  
Formatting a microSD card permanently removes all files stored on the card.  
1.  
From home, tap  
Apps >  
Settings >  
Storage.  
2. Scroll down the screen, tap Format SD card > Format SD card > Delete all.  
Tools and Calendar  
122  
     
Note: Formatting erases all the data on an installed microSD card, after which the files CANNOT be  
retrieved. To prevent the loss of important data, please check the contents before you format the  
card.  
Unmount a microSD Card  
When you need to remove an optional installed microSD card, you must unmount the card first to  
prevent corrupting the data stored on it or damaging the card.  
1.  
From home, tap  
Apps >  
Settings >  
Storage.  
2. Tap Unmount SD card.  
3. Remove the microSD card. See Remove a microSD Card.  
Transfer Files Between Your Phone and a  
Computer  
You can use the supplied USB cable to connect your phone directly to your computer and transfer  
music, pictures, and other content files. For example, if you have a music album stored on your  
computer that you want to listen to on your phone with the music player, Google Play Music, or  
Sprint Music Plus, just attach your phone to the computer and copy the files to the Music folder.  
1. Connect your phone to your computer using the supplied USB/charging cable. You may need to  
remove the USB cable from the Charging Head.  
l
Insert one end of the cable into the USB Charger/Accessory port at the bottom of the phone.  
Insert the other end of the cable into an available USB port on your computer.  
l
2. Your phone will automatically detect the connection. Continue to set up the connection:  
l
When  
appears in the Status bar, swipe your finger down from the Status bar to open the  
Notification panel. The Notification panel shows the type of connection.  
l
To change the connection type, tap it in the Notification panel, and then choose an option:  
o
Connected as a media device: Used for most transfers. You can transfer files in  
Windows or from a Mac.  
o
Connected as a camera: Used for transfers of photos using camera software on your  
computer.  
3. On your computer, navigate to view the contents of your phone (for example, using My  
computer).  
Tools and Calendar  
123  
   
4. Select a folder (for example, Music for songs and albums) and copy files to it from your  
computer.  
5. When you are done, disconnect your phone from the computer.  
System Updates  
From time to time, updates may become available for your phone. Use System update options to  
update your phone’s internal software.  
Before Updating Your Firmware  
Updating your phone firmware will erase all user data from your phone. You must back up all critical  
information before updating your phone firmware.  
Back Up Information to Your Google Account  
1.  
From home, tap  
Apps >  
Settings >  
Backup and reset.  
2. Tap Back up my data to turn on the feature (checkmark).  
l
l
Tap Backup account to choose or sign in to a Google account to use for backups.  
Tap Automatic restore if you want information saved to the Google account above to be  
restored when you reinstall apps, such as after a firmware update, or when setting up a new  
device.  
Back Up Account Information  
1.  
2.  
3.  
From home, tap  
Apps >  
Settings.  
Tap  
Tap  
Accounts, and then tap an account.  
Menu > Sync all.  
Preserve Information on an Optional Installed Memory Card  
As an added precaution, to preserve any data on an optional installed microSD card, please remove  
it from your phone prior to starting the update process.  
Update Your Phone  
Use the System Update setting to update your phone’s software, firmware, Preferred Roaming List  
(PRL), and other features.  
Tools and Calendar  
124  
     
1.  
From home, tap  
Apps >  
Settings > System Update.  
2. Select an option:  
l
l
Update now: Check for software updates, and install them, if desired.  
Auto update: When enabled, your phone will automatically check for updates and install  
them.  
l
l
l
Wi-Fi only: When enabled, your phone will only download updates when your phone is  
connected to a Wi-Fi network.  
Update PRL: Download and the latest Preferred Roaming List (PRL), used by your phone  
to access the network.  
Update Profile: Update the user profile related to your wireless service account. If you  
choose to change your user name online, use this option to update the user name on your  
phone.  
l
UICC Unlock: Unlock your device’s Universal Integrated Circuit Card.  
Tools and Calendar  
125  
Sprint Worldwide Wireless Service  
With your phone and global roaming service from Sprint WorldwideWireless Service, you can  
make phone calls and use wireless data services around the globe on compatible CDMA and  
GSM/UMTS networks. For a country-specific travel guide, select your device and destination from  
Activate Sprint Worldwide Service on  
Your Account  
Before using your phone in global roaming mode, you must activate Sprint Worldwide service.  
To activate Sprint Worldwide service:  
n
Chat with or email an international support rep by visiting sprint.com/swwsupport.  
– or –  
Call Sprint Worldwide Customer support at 1-888-226-7212.  
Your Phone’s SIM Card for International  
Roaming  
Your phone comes with a preinstalled SIM (Subscriber Identity Module) card to support roaming on  
compatible GSM networks.  
Note: Your SIM card should be preinstalled. If you need to reinstall your SIM card, follow the  
instructions below. The SIM included contains information specific to your phone and should be  
retained with the phone for use on GSM networks.  
1. Using the slot provided, gently lift the cover off the phone. Remove the battery.  
2. Hold the SIM card so that the metal contacts on the SIM card face down and the cut off corner  
points to the bottom-right corner of your phone.  
3. Slide the SIM card into the SIM card slot until it stops.  
4. Replace the battery and battery cover.  
Sprint Worldwide Wireless Service  
126  
     
Set Network Mode Options  
In order to roam internationally on different types of network technology (CDMA/LTE and  
GSM/UMTS), you may need to set your phone’s network mode to allow use of a specific technology.  
Once set, your phone is designed to enter global roaming mode automatically when you activate  
your Sprint Worldwide service, meaning that it should automatically connect to an appropriate  
CDMA/LTE or GSM/UMTS network when you travel.  
To set your network mode options manually:  
1.  
From home, tap  
Apps >  
Settings >  
More networks  
2. Tap Mobile networks > Network mode to configure options:  
l
l
l
To allow connections to CDMA or LTE networks only, touch CDMA or LTE/CDMA.  
To allow connections to GSM or UMTS networks only, touch GSM/UMTS.  
To allow connections to available CDMA/LTE or GSM/UMTS networks, touch Automatic.  
This is the recommended setting for international use.  
Make and Receive Worldwide Calls  
When travelling on international networks, you can place and answer calls as you would on the  
Sprint network (see Make Phone Calls and Receive Phone Calls), although some additional  
instructions may be required to place a call. Some features and services are not available in all  
countries. For more information on services that are available while roaming, visit sprint.com/sww.  
Make Calls Using Plus (+) Code Dialing  
Placing calls from one country to another country is simple with the Plus (+) Code Dialing feature.  
When placing international calls, you can use Plus Code Dialing to enter the appropriate  
international access code for your location (for example, 011 for international calls placed from the  
United States).  
Note: Plus Code Dialing is only available when roaming internationally on GSM networks and on  
certain CDMA networks in the United States, Canada, and the Caribbean.  
Note: International access codes and dialing information are available online at sprint.com/sww.  
To use Plus Code Dialing to place an international call:  
1.  
From home, tap  
Phone > Keypad to display the phone screen.  
2. Dial the appropriate sequence for your location:  
Sprint Worldwide Wireless Service  
127  
     
l
l
If you are on the GSM network, touch  
symbol automatically inserts the international access code for the country from which you are  
calling.)  
to insert a “+” on the dialer screen. (The “+”  
If you are on the CDMA network outside Canada or the Caribbean, enter the international  
access code for the country from which you are calling.  
3.  
4.  
Touch  
Touch  
to insert the US country code, and then enter the area code and number.  
to place the call.  
Sprint International Voicemail Service  
Your Sprint voicemail will follow you as you travel. All of your unanswered calls will be forwarded to  
your Sprint voicemail. You will need to be sure your voicemail box is already set up and that you  
know your voicemail password.  
Note: Sprint voicemail may not be available on all networks; check sprint.com/sww for service  
information.  
Set Up Your Voicemail Access Number for  
International Use  
To simplify accessing your Sprint Voicemail while travelling, you can set up your voicemail access  
number as a Contacts entry. Save the voicemail access number with the international dialing code,  
to make it faster and easier to access your messages while roaming internationally.  
1.  
2.  
From home, tap  
Apps >  
Contact.  
Touch to add a contact.  
3. If you have accounts set up on your phone, tap a storage account.  
4. Enter a name for the new contact, for example, “Voicemail”.  
5.  
Touch  
(+1), your area code, and your wireless phone number.  
6. Touch Save.  
Access Your Voicemail Internationally  
You will need to call your voicemail number to access your voicemail while roaming internationally.  
Sprint Worldwide Wireless Service  
128  
     
New Message Indicators  
Your voicemail message indicators may be displayed differently when roaming internationally.  
n
A “Message Waiting” indicator icon or a text message is displayed when a voicemail message is  
received.  
n
n
You may see “Missed Call” on your screen prior to receiving a message notification.  
You must call voicemail in order to retrieve messages. Follow the instructions on the previous  
page to store your voicemail number for easy access.  
Retrieve Voicemail Messages  
The voicemail retrieval process while travelling is the same as on the Sprint Network; however, you  
will be required to enter your voicemail password.  
To retrieve your voicemail messages:  
1.  
2.  
From home, tap  
number to call it.  
Phone > Contacts tab, touch the voicemail entry and then touch the  
When your voicemail answers, touch  
your voicemail.  
, enter the password, and touch  
to access  
International Voicemail Troubleshooting  
There are a few tips to keep in mind when using Sprint voicemail while traveling.  
n
Some carriers may not support voicemail indicators. It may be necessary to call your voicemail to  
see if you have any new messages.  
n
If you hear the message “Please enter the number of the subscriber you wish to call,” enter your  
10-digit wireless phone number.  
International Data Roaming  
Sprint Worldwide Wireless Service can also keep you connected via email and Web browsing when  
travelling in countries in which Sprint offers data service. Data services are available on both CDMA  
and GSM/UMTS networks. Check sprint.com/sww to determine the services available where you  
are travelling.  
Note: Prior to using your Sprint Worldwide GSM/UMTS Data Services, you must establish and  
utilize your CDMA data services domestically on the Sprint Network.  
Sprint Worldwide Wireless Service  
129  
   
Get Started With Sprint Worldwide Data Services  
To use Sprint Worldwide Data Services, you will need to have these services activated on your  
account.  
n
To activate, call Sprint Worldwide Customer Support at 1-888-226-7212. Representatives are  
available 24 hours a day, 7 days a week to assist you.  
Access Email and Data Services Internationally on  
GSM/UMTS Networks  
To access your email and browse the Web when travelling, you may need to manually select the  
carrier that provides Sprint service in your location. You can find a list of carriers for each country  
where GSM data service is offered at sprint.com/sww. Then, follow the instructions below to select  
the appropriate carrier network on your phone.  
To select a GSM data service carrier for a specific country:  
1.  
From home, tap  
Apps >  
Settings >  
More networks > Mobile networks.  
2. Ensure the Mobile data check box is selected.  
3. Tap Network mode, and then change the preferred network mode to Automatic.  
Access Email and Data Services on Internationally on  
CDMA Networks  
If data service is available on a CDMA network, then you only need to set the phone to CDMA, you  
will not need to select the specific carrier. Selecting a specific carrier is only necessary for providers  
on the GSM network. If your phone has automatically selected a GSM network while traveling, then  
you will need to set the phone to CDMA to access CDMA data services. (See Set Network Mode  
Options.) Visit sprint.com/sww for a list of services available in each country.  
International Roaming Status Messages  
You may receive status messages under certain conditions. Before contacting Sprint Worldwide  
Customer Support, note the message, numeric code, and the conditions under which it appeared.  
The following table lists and describes the status messages.  
Sprint Worldwide Wireless Service  
130  
       
Status Messages  
Number Not in Service  
User Not Available  
Message Description  
The number that you entered is not valid.  
The phone that you called is either busy, out-of-range, or turned  
off. Please try again later.  
User Not Authorized  
The phone that you called is either busy, out-of-range, or turned  
off. Please try again later.  
Please Try Later  
This service is temporarily not available. Please try again later.  
Service Restricted  
Service may not be activated properly. Please contact Sprint  
Customer Service to report the issue for resolution.  
Service Not Available  
Emergency Calls Only  
This feature is not available on the current network.  
Either the service is not activated properly or the current network  
is available for emergency calling only. Adjust your network  
settings to check for other available networks. If service is still not  
available after adjusting the settings, contact Sprint Customer  
Service to report the issue for resolution.  
System Busy. Try Later  
Service Conflict  
The system is experiencing heavy traffic. Please try again later.  
This service cannot be enabled because an incompatible service  
has already been turned on.  
Please Try Again  
Self Check Error  
An error occurred. Note the error code and try again.  
A fault was detected with your phone. If this error recurs, note the  
error and contact Sprint Customer Service.  
Self Check Fail  
Wrong PIN  
An operational fault was detected with your phone. Note the  
numeric code, turn your phone off, and contact Sprint Customer  
Service.  
You have entered an incorrect SIM PIN number. You have only  
three attempts to enter your PIN. After a third unsuccessful  
attempt, your phone will be locked and you will have to call Sprint  
Customer Service to have it unlocked. Sprint sets the default to  
PIN off; if you elect to enable the PIN then you will need to contact  
Sprint for the default PIN and PUK.  
PIN Blocked. Call Your  
Provider  
An incorrect SIM PIN was entered three consecutive times. You  
will be unable to send or receive calls on your phone. Contact  
Sprint Customer Service to obtain the PIN Unblocked Key (PUK)  
code. Sprint sets the default to PIN off; if you elect to enable the  
PIN then you will need to contact Sprint for the default PIN and  
PUK.  
Insert SIM  
Your SIM Card is not being detected. Please check to ensure that  
you have inserted the SIM Card.  
Check SIM Card  
Please check your SIM card to make sure it is properly inserted.  
Sprint Worldwide Wireless Service  
131  
Contact Sprint for Assistance with  
International Service  
If you experience any issues with voice or data services while outside of the United States, Sprint  
offers customer support 24 hours a day. In the event that you do experience an issue, try the  
following actions:  
n
First try powering your phone off and then back on; this will force your phone to reregister with  
the network.  
n
Try manually selecting another network. Information for selecting networks can be found in the  
phone guide.  
If neither of these actions resolves your issue, you will need to contact customer service (see below).  
When calling to report an issue, the following information will be beneficial in trying to resolve your  
issue as quickly as possible:  
n
n
n
n
n
Your wireless phone number.  
The city and country you are travelling in.  
Any error message that displays on your phone or that you heard when trying to place a call.  
If the issue is with data, were you able to place voice calls?  
If the issue is with voice service, were you able to access data?  
Please call the numbers below if you need assistance:  
While in the United States: Call 1-888-226-7212.  
While traveling outside the United States:  
n
In GSM mode: touch  
and then dial 1-817-698-4199.  
n
In CDMA mode: enter the country code and then dial 1-817-698-4199.  
There is no charge for this call from your wireless phone.  
From a landline phone when outside the United States:  
Sprint Worldwide Customer Support can be reached from a landline phone at 1-817-698-4199.  
Access or connection fees may apply. The toll free numbers below can also be used to contact  
Sprint Worldwide Customer Support in the following countries:  
Country  
From Landline Phone  
1-888-226-7212  
Caribbean (Anguilla, Barbados,  
Sprint Worldwide Wireless Service  
132  
 
Country  
Cayman Islands, and Dominica)  
France  
From Landline Phone  
0800-903200  
Germany  
0800-180-0951  
800-787-986  
Italy  
Mexico  
001-877-294-9003  
1-800-201-7545  
0808-234-6616  
Trinidad and Tobago  
United Kingdom  
Note: This toll free service is available on ordinary landline phones and some public pay phones.  
This service does not cover any hotel access charges.  
Sprint Worldwide Wireless Service  
133  
Settings  
Use Settings to configure your phone to your preferences.  
Using Settings  
Use Settings to configure your phone to your preferences.  
Access Settings  
You can access Settings in a variety of ways.  
n
From home, tap  
– or –  
Apps >  
Settings.  
From home, touch and hold on the Status bar, and then drag down to display the Notification  
panel. Tap Settings to access Settings.  
Search Settings  
Enter key words to search for settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Search, and then enter key words.  
Settings Options  
Configure options to make Settings easy for you to use.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Menu for these options:  
l
List view/Grid view: Display Settings in a list, or grid layout.  
l
Tab view: Display Settings on tabs, by category.  
Settings  
134  
         
l
l
Edit quick settings: Twelve quick settings appear at the top of the list or grid of Settings.  
Tap settings to select them for display as quick settings.  
Help: Learn about Settings.  
Wi-Fi Settings  
Use Wi-Fi settings to control your phone’s connections to Wi-Fi networks, and for using Wi-Fi Direct  
to connect directly to other Wi-Fi Direct devices.  
Configure Wi-Fi Settings  
Set up and manage wireless access points.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Wi-Fi, and then tap the ON/OFF switch beside Wi-Fi to turn Wi-Fi on. Wi-Fi must be On  
to configure settings.  
3. Configure settings:  
l
Tap Add Wi-Fi network to connect to a new Wi-Fi network. For more information about  
using Wi-Fi, see Wi-Fi.  
l
Tap  
Menu for these options:  
o
Scan: Search for available Wi-Fi networks.  
o
o
o
o
o
Wi-Fi Direct: Connect to other Wi-Fi Direct devices. For more information, see Wi-Fi  
Direct Settings.  
Advanced: Configure more settings. For more information, see Advanced Wi-Fi  
Settings.  
WPS push button: Set up a connection to a WPS (Wi-Fi Protected Setup) router or  
other equipment.  
WPS PIN entry: View the PIN used by your device to set up a PIN-secured connection  
to a Wi-Fi router or other equipment.  
Help: Learn about setting up and using Wi-Fi networks, and other settings.  
Advanced Wi-Fi Settings  
Set up and manage wireless access points.  
Settings  
135  
       
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Wi-Fi, and then tap the ON/OFF switch to turn Wi-Fi on. Wi-Fi must be on to configure  
settings.  
3.  
Tap  
Menu > Advanced to configure these settings:  
l
l
Network notification: When enabled, your phone alerts you when a new Wi-Fi network is  
available.  
Passpoint: When turned on, your phone will connect to passpoint-enabled Wi-Fi networks  
automatically.  
l
l
Sort by: Choose a sorting order for Wi-Fi networks on the Wi-Fi screen.  
Keep Wi-Fi on during sleep: Specify when to switch from Wi-Fi to mobile data for data  
communications, when the device goes to sleep (when the backlight goes out). This setting  
can affect data usage, and the behavior of devices you connect to your device, such as when  
using it as a hotspot.  
l
l
Always allow scanning: When enabled, your phone will allow Google location service and  
other apps to scan for networks, even when Wi-Fi is turned off.  
Smart network switch: When enabled, your phone will automatically switch between  
known Wi-Fi networks and mobile networks. Known Wi-Fi networks are those you have  
already connected to.  
l
l
l
l
Wi-Fi timer: When turned on, your phone will automatically connect or disconnect from a  
Wi-Fi network, using the Starting time and Ending times you set.  
Install certificates: If you have certificates stored on an installed optional memory card (not  
included), you can use this option to install the certificates.  
MAC address: (Not configurable) View your device’s MAC address, needed for connecting  
to some secured networks.  
IP address: (Not configurable) View your device’s IP address.  
Wi-Fi Direct Settings  
Wi-Fi Direct allows devices to connect to each other directly via Wi-Fi, without a Wi-Fi network or  
hotspot, and without having to set up the connection. For example, your device can use Wi-Fi Direct  
to share photos, contacts and other content with other Wi-Fi Direct devices.  
1.  
From home, tap  
Apps >  
Settings.  
Settings  
136  
 
2.  
3.  
Tap  
Wi-Fi, and then tap the ON/OFF switch beside Wi-Fi to turn Wi-Fi on. Wi-Fi must be on  
to configure Wi-Fi Direct settings.  
Tap  
Menu > Wi-Fi Direct. Your device automatically scans for nearby Wi-Fi Direct  
devices, or you can tap Scan to start scanning.  
4. After scanning for devices, select a device, and then follow the prompts to complete the  
connection.  
– or –  
Tap  
Menu > Multi connect to scan for devices that support multi connect. Select the  
devices and follow the prompts to establish the connections.  
Hotspot Settings  
Use the Hotspot feature to share your phone’s data connection with other devices via Wi-Fi.  
Note: Using the Hotspot feature consumes battery power and uses data services.  
Turn Hotspot On or Off  
To conserve battery life, turn Hotspot on when you need it and turn it off when you’re finished. You  
can control Hotspot from Settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Hotspot, and then tap the ON/OFF switch beside Hotspot to turn Hotspot on or off.  
Configure Hotspot  
Set up Hotspot to your preferences.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Hotspot > Menu to set these options:  
l
Configure:  
o
Network SSID: View and change the name of your mobile hotspot.  
Settings  
137  
     
o
Hide my device: When enabled, your mobile hotspot is not visible to other Wi-Fi devices  
during a scan. Other devices can still connect to your mobile hotspot, but will have to set  
up the connection manually with your Network SSID and Password.  
o
o
Security: Choose the security level for your Mobile Hotspot.  
Password: If you choose a security level that uses a password, set a password. By  
default, the password is your mobile telephone number.  
o
o
Show password: When enabled, the contents of the Password field are visible.  
Show advanced options: When enabled, you can access advanced options, including  
Broadcast channel, to specify the channel your device uses for Hotspot, and you can set  
the maximum number of connections to your Hotspot.  
l
l
Timeout settings: Choose a time period, after which Hotspot will automatically turn off if  
there is no activity.  
LAN settings: View and configure settings related to using your Hotspot as a Local Area  
Network.  
o
IP address: View the default IP address, or tap to enter a valid IPv4 address.  
o
Subnet mask: View the default subnet mask, or tap to enter a subnet mask.  
o
DHCP: Tap to enable or disable DHCP. When DHCP is enabled, your phone assigns IP  
addresses to devices that connect to Hotspot.  
o
Starting IP: When DHCP is enabled, view the default starting IP address for assigning  
IP addresses to connecting devices, or enter a enter a valid IPv4 address. When other  
devices connect to your device using DHCP, the IP address your phone assigns will be  
between the Starting IP and Ending IP.  
o
Ending IP: When DHCP is enabled, view the default ending IP address for assigning IP  
addresses to connecting devices, or enter a enter a valid IPv4 address. When other  
devices connect to your device using DHCP, the IP address your phone assigns will be  
between the Starting IP and Ending IP.  
o
Lease time: When DHCP is enabled, set a length of time a connected device may use  
an assigned IP address.  
o
Maximum DHCP users: When DHCP is enabled, set the maximum number of devices  
allowed to connect to your Hotspot.  
Allowed Devices  
Control whether devices can connect to your Mobile Hotspot with the Allowed devices list. After you  
add devices to the list, they can scan for your phone and connect using your phone’s Hotspot name  
and password.  
Note: Using the Hotspot feature consumes battery power and uses data services.  
Settings  
138  
 
1.  
2.  
3.  
From home, tap  
Apps >  
Settings.  
Tap  
Hotspot >  
Menu > Allowed Devices.  
Tap  
, and then enter the other device’s Device name and MAC address. Consult the other  
device’s settings to find these details.  
4. Tap OK to add the device to the Allowed devices list.  
Bluetooth Settings  
Bluetooth is a short-range wireless communications technology for exchanging information over a  
distance of about 30 feet. You don’t need to line up the devices to send information with Bluetooth. If  
the devices are in range, you can exchange information between them, even if they are in different  
rooms.  
Your device can use Bluetooth to share photos, contacts and other content with other Bluetooth  
devices. Many of the apps on your device provide options for sharing via Bluetooth under  
or with the Share icon.  
Menu,  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Bluetooth, and then tap the ON/OFF switch to turn Bluetooth on. Bluetooth must be on  
to configure settings.  
3. From the Bluetooth screen, configure these settings:  
l
Tap the ON/OFF switch to turn Bluetooth on or off.  
l
Tap your device’s name to enable or disable visibility to other Bluetooth devices. When your  
device is visible, other devices can find your devices during a scan. Your device remains  
visible for the period of time set in the Visibility timeout setting.  
l
l
Tap a paired device to connect to it, or touch  
beside a device to change its settings.  
Tap Scan to search for visible Bluetooth devices. After searching, tap a device to pair with it.  
4.  
Tap  
Menu for more settings:  
l
Visibility timeout: Set the length of time your device is visible to other devices when you  
turn on visibility.  
l
Received files: View files transferred to your device via Bluetooth.  
Settings  
139  
 
l
l
Rename device: Change the name your phone uses to identify itself when you make your  
phone visible to other Bluetooth devices.  
Help: Learn about Bluetooth, and other settings.  
Tethering Settings  
Use Tethering to share your device’s Internet connection with a computer that connects to your  
device via USB cable, or by Bluetooth.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Tethering to choose an option:  
l
USB tethering: Connect the computer to your phone via USB cable, and then touch USB  
tethering to turn tethering on or off.  
l
Bluetooth tethering: Pair your device with the computer via Bluetooth. Consult the  
computer’s documentation for more information about configuring your computer to pair via  
Bluetooth. Touch Bluetooth tethering to turn tethering on or off.  
Note: Tap  
Menu > Help for information about using Tethering.  
Airplane Mode  
When you turn on Airplane mode, your phone disconnects from all networks, meaning you cannot  
use make calls, send or receive messages, or access the Internet. It also turns off other connectivity  
features, such as Wi-Fi and Bluetooth.  
While in airplane mode, you can use other features of your device, such as playing music, watching  
videos, or other applications.  
To use Wi-Fi and Bluetooth after turning on Airplane mode, turn them on in Settings, or on the  
Notification panel.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Airplane mode, and then tap the ON/OFF switch beside Airplane mode to enable or  
disable the option.  
Note: You can also control Airplane mode from the Device options menu. Press and hold the  
Power/Lock key, and then tap Airplane mode.  
Settings  
140  
   
Data Usage Settings  
Monitor data usage, and control your device’s connection to mobile data service.  
Note: Data is measured by your phone. Your service provider may account for data usage  
differently.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Data usage to configure options:  
l
Mobile data: Enable or disable your phone’s access to mobile data service. You can also  
control mobile data at the Notification panel.  
l
l
l
Limit mobile data usage: When enabled, your mobile data connection will be disabled  
when the specified limit is reached. After enabling the setting, drag the red limit line on the  
graph below to set the data usage limit.  
Alert me about data usage: When enabled, your device will alert you when mobile data  
usage reaches the warning limit you set. After enabling the setting, drag the orange warning  
line on the graph below to set the data usage warning limit.  
Data usage cycle: Tap the menu, and then choose a time period for data usage. Data  
usage for the period displays on the graph, along with usage by application below.  
3.  
Tap  
Menu for other options:  
l
Data roaming: When enabled, your device can connect tomobile data service when outside  
your home network area. Using data while roaming may incur additional costs; contact your  
service provider for more information.  
l
Restrict background data: Your device is capable of connecting to the network in the  
background, for synchronization or other services. When enabled, background connections  
will not occur.  
l
l
l
Auto sync data: When enabled, your device will synchronize with accounts automatically,  
at any time.  
Show Wi-Fi usage: When turned on, a separate tab displays data used while connected to  
Wi-Fi.  
Mobile hotspots: Select Wi-Fi networks that are mobile hotspots. You can restrict apps  
from using these networks, and you can configure apps to warn you before using these  
networks for large downloads.  
l
Help: Learn about data usage settings.  
Settings  
141  
 
Location Settings  
Control apps’ access to your location, and configure location sources. Some apps may require one  
or more location services be turned on for full app functionality. When Location is turned on, you are  
allowing Google’s location service to collect anonymous location data. Some data may be stored on  
your device, and collection may occur even when no apps are running.  
GPS signals may be affected by your surroundings, including:  
n
n
n
n
n
Buildings  
Tunnels or underground structures  
Weather conditions  
High-voltage or electromagnetic fields  
Tinted windows  
Note: E 9-1-1 location service is standard on all mobile phones, to allow sharing of GPS information  
with emergency personnel when you make a call to emergency services, such as 9-1-1.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Location, and then tap the ON/OFF switch beside Location to turn location services  
on or off. Location must be turned on to configure settings. When you turn Location on, you are  
allowing Google’s location service to collect anonymous location data. Some data may be stored  
on your device, and collection may occur even when no apps are running.  
3. After you turn Location on, you can configure settings:  
l
Mode: Choose the method your phone uses to determine your location.  
o
High accuracy: When enabled, your phone uses GPS information, Wi-Fi, and mobile  
networks to estimate your location.  
o
Power saving: When enabled, your phone uses Wi-Fi and mobile networks to estimate  
your location.  
o
GPS only: When enabled, your phone uses only GPS information to estimate your  
location. (Wi-Fi and mobile network information is not used.)  
l
Recent location requests: View services or apps that have recently accessed your  
location information.  
l
l
Location services: Select sources for reporting your location information to Google.  
Location sources: Tap My places to save your favorite locations, to allow your device to  
provide relevant information by recognizing saved locations.  
Settings  
142  
 
o
o
Tap Home, Work, or Car, and then follow the prompts to configure options for  
identifying the location.  
Tap  
to set up a new location.  
More Networks Settings  
More networks settings provide additional options for configuring connections between your phone  
and the network or to other devices.  
Default Messaging App Settings  
If you have multiple messaging apps installed on your phone, you can choose the app your phone  
uses for messaging. The app you select here will be used when you choose Messages in other apps,  
such as when sharing items like pictures or video.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap More networks > Default messaging app.  
3. Choose a messaging app. The default Messages app included with your phone is available,  
along with any other messaging apps you’ve installed.  
Note: If you choose a default messaging app other than Messages (for example, Google Hangouts),  
you will not be able to use the standard Messages app unless you restore it as the default messaging  
app.  
Mobile Networks Settings  
Set options for network selection and data service.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap More networks > Mobile networks.  
3. Configure options:  
l
Mobile data: When enabled, your device connects to the mobile data network, and can use  
the network to access the Internet and transfer information.  
l
Network mode: Choose a preferred network mode. Available options depend on your  
phone’s features.  
Settings  
143  
       
l
Connections optimizer: When enabled, Connections optimizer helps you manage and  
enhance your data experience by finding and connecting to “remembered” Wi-Fi networks,  
and, if applicable, the Sprint Spark Enhanced LTE Network. Remembered networks are  
those to which you have already connected.  
l
l
Access Point Names: Configure access points (not common).  
Network operators: Configure network operators.  
VPN Settings  
Set up and manage Virtual Private Networks (VPN).  
Note: VPN settings include storage of login credentials on your device. You must configure a screen  
unlock PIN or password before setting up a VPN.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
More networks > VPN > Basic VPN. (If prompted, configure a screen lock PIN or  
password before continuing.)  
3.  
Tap  
to add a VPN, and then enter details for the VPN. Available options depend on the type  
of VPN; consult your VPN’s administrator for more information.  
l
Name: Enter the name of the VPN.  
l
Type: Choose the type of VPN, from PPTP, L2TP/IPSec PSK, L2TP/IPSec RSA, IPSec  
Xauth PSK, IPSec Xauth RSA, or IPSec Hybrid RSA.  
l
l
l
Server address: Enter the VPN server address.  
PPP Encryption (MPPE): Tap to enable, if applicable for the VPN.  
Show advanced options: Tap to set other options, depending on the type of VPN.  
4. Tap Save to save the VPN.  
Tip: For advanced VPN setup, tap Advanced IPSec VPN from the VPN screen, and then follow  
the prompts.  
Roaming Settings  
When you are outside your home network area, your phone can still connect to other networks that  
your provider supports via roaming. There may be additional costs for accessing networks while  
roaming, so you may want to control your phone’s roaming behavior with Roaming settings.  
Settings  
144  
   
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap More networks > Roaming.  
3. Configure options:  
l
l
l
Roaming network: Select a roaming default. Choose Home only, to only connect to the  
Sprint network, or Automatic, to allow connections to Sprint’s partner networks, when  
available.  
Roaming settings: Choose options for roaming, including Voice and data for Domestic  
CDMA and International CDMA networks, and Data for GSM networks (if supported by your  
phone).  
Roaming guard: Choose options for preventing roaming for certain functions. Enable or  
disable roaming access for Voice and data for Domestic CDMA, Voice, Data and Outgoing  
SMS for International CDMA networks, and Voice, Data and Outgoing SMS for GSM  
networks (if supported by your phone).  
NFC Settings  
Use NFC (Near Field Communication) to share information between your device and another NFC  
device by touching the devices together, typically back-to-back.  
NFC is used with S Beam and Android Beam, and must be turned on to use these features.  
Turn NFC On or Off  
Use NFC (Near Field Communication) to share information between your device and another NFC-  
capable device or NFC tag, by touching the devices together, typically back-to-back. For example,  
you can beam Web pages from the browser, contacts from Contacts, and videos from YouTube.  
The app determines what is beamed.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap NFC, and then tap the ON/OFF switch beside NFC to turn NFC on or off.  
Android Beam  
With Android beam, you can transmit app content via NFC to other NFC devices that support  
Android Beam.  
Android Beam uses NFC, so NFC must be turned on before you can turn on Android Beam.  
Settings  
145  
     
Turn Android Beam On or Off  
Turn on NFC and Android Beam, so that beaming is available from the apps on your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap NFC, and then tap the ON/OFF switch beside NFC to turn NFC on or off.  
3. Tap Android Beam and then tap the ON/OFF switch beside Android Beam to turn Android  
Beam on or off.  
S Beam Settings  
Share more and share it faster with S Beam. From photos to documents, large video files to maps,  
you can share almost anything instantly with one touch, simply by placing your devices back-to-back.  
S Beam uses your device’s NFC (Near Field Communication) feature to send, or “beam,” content to  
other NFC devices.  
S Beam works in the background. Use the sharing options from your favorite apps to select content  
to share via S Beam. For example, you can beam pictures or videos from Gallery, or songs from  
Music player. Just bring the devices together (typically back to back), and then tap the screen.  
Note: You must have both NFC and S Beam turned on to use S Beam to share information.  
Turn S Beam On or Off  
When S Beam is turned on, you can send or receive data by touching your device to another NFC-  
capable device.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
NFC, and then tap the ON/OFF switch beside NFC to turn NFC on or off. NFC must be  
turned on before you can turn S Beam on.  
3. Tap S Beam, and then tap the ON/OFF switch beside S Beam to turn S Beam on or off.  
Note: Tap Menu > Help for information about using S Beam.  
Tap and Pay  
With your phone and a payment app, you can use your device to pay for items by tapping it to an item  
at the point-of-purchase. Google Wallet is an example of a payment app. You must have the  
payment app set up on your phone to use it with Tap and Pay.  
Settings  
146  
   
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
NFC, and then touch the ON/OFF switch beside NFC to turn NFC on. NFC must be on  
to use Tap and Pay.  
3. Touch Tap and Pay to access Tap and Pay settings. Available settings depend on the payment  
app(s) you have set up on your phone.  
Nearby Devices Settings  
Share files with devices that support DLNA (Digital Living Network Alliance) standards, over Wi-Fi.  
To use Nearby devices, you must connect to the same Wi-Fi network as the devices you wish to  
share with, and the other devices must support DLNA. From an app, look for the Nearby devices  
sharing options.  
Note: Use care when enabling file sharing. When enabled, other devices can access data on your  
device.  
Turn Sharing via Nearby Devices on or off  
To use sharing with nearby devices, you must have the option turned on.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Nearby devices to configure these options:  
l
Tap the ON/OFF switch beside Nearby devices to turn Nearby devices on or off. Nearby  
devices must be turned on to configure options.  
l
Under Advanced, configure options to control how content is shared from your device:  
o
Shared contents: Choose the type of content to share, from Videos, Photos, or Music.  
o
Allowed devices: View and manage a list of devices allowed to connect to your device.  
o
Denied devices: View and manage a list of devices restricted from connecting to your  
device.  
o
Download to: Choose a location to save downloaded content, from USB storage  
(device memory) or optional installed SD card (not included).  
o
Download from other devices: Choose how to handle incoming files from other  
devices, from Always accept, Always ask, or Always reject.  
Settings  
147  
 
Printing Settings  
You can print from your phone, via Wi-Fi, to an optional compatible printer (not included). Your  
phone and the optional printer must be connected to the same Wi-Fi network.  
Turn Print Services On or Off  
Before you can print from your phone, a print service must be turned on. The print service  
communicates with the printer when you select something to print.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Printing, and then choose a print service from the list. The Samsung Print Service  
Plugin is available by default.  
3. Tap the ON/OFF switch to turn the service on or off. The service must be on to configure settings  
or print.  
Add a Printer  
Before you can print to a printer, you must set it up on your phone. You’ll need to know the IP  
address of the printer; consult the printer’s documentation for this information.  
1.  
2.  
From home, tap  
Tap Printing.  
Apps >  
Settings.  
3. Choose a print service from the list, and then tap the ON/OFF switch to turn the service on or off.  
The service must be on to add a printer.  
4.  
Tap  
Menu > Add printer >  
, and then enter a name and the IP address of the printer.  
Configure Print Settings  
Choose options for printing from your phone.  
Note: Below settings are examples only. Available settings will differ depending on the type of print  
service and printer you are using.  
1.  
2.  
From home, tap  
Tap Printing.  
Apps >  
Settings.  
3. Choose a print service from the list, and then tap the ON/OFF switch to turn the service on or off.  
The service must be on to add a printer.  
Settings  
148  
 
4.  
Tap  
Menu > Settings to configure options. Available options may vary depending on the  
type of printer, and not all printers support all options.  
l
2-Sided printing for documents: Choose Simplex to print one page per piece of paper, or  
choose Long edge or Short edge to print on both sides. Short edge and Long edge refer to  
how the pages flip when moving through multiple pages.  
l
l
Secure Release: If the optional printer supports secure release, and it is enabled, you must  
enter a User ID to retrieve your printouts. Tap Secure release, and then enter a User ID.  
Confidential Print: If the optional printer supports confidential printing, and it is enabled,  
you must enter a User ID and Password to retrieve your printouts. Tap Confidential Print,  
and then enter a User ID and Password.  
l
Job Accounting: If the optional printer supports job accounting, and it is enabled, you must  
enter a User ID and Password when printing, to track printing by group or other set.  
l
l
l
Version: View the version of the print service software.  
Open source licenses: View licenses related to the print service software.  
About: View information about the print service software.  
Screen Mirroring Settings  
With Screen mirroring, you can share your device’s screen with another device, using an optional  
AllShare Cast accessory (not included).  
Turn Screen Mirroring On or Off  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Screen mirroring, and then tap the ON/OFF switch beside Screen Mirroring to turn  
Screen mirroring on or off.  
Sound Settings  
Configure the sounds and vibrations your phone plays, for incoming calls, notifications, screen  
touches, connections, and other options.  
Sound Mode  
You can switch between sound modes, while preserving the individual sound settings you’ve made.  
Settings  
149  
     
Note: Sound modes are also available from the Device options menu. Press and hold the  
Power/Lock key, and then choose Mute, Vibrate, or Sound from the Device options.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Sound mode, and then choose a mode:  
l
Mute: Your phone plays no sounds or vibrations. Onscreen reminders will still occur.  
l
Vibrate: Your phone vibrates for notifications and alerts. This uses the Vibration intensity  
you choose in Sound settings.  
l
Sound: Your phone uses the sounds, vibrations, and volume levels you’ve chosen in Sound  
settings for notifications and alerts.  
Volume  
Set the system volume level, and set default volume for call ringtones, notifications, and other media.  
Note: You can also set System volume from the home screen by pressing the Volume key.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Volume and then drag the sliders to set the default volume for:  
l
l
l
l
Music, video, games, and other media  
Ringtone  
Notifications  
System  
3. Tap OK to save the settings.  
Vibration Intensity  
Set the level for vibration to accompany ringtones, notifications, and feedback for your screen  
touches, also known as haptic feedback.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Vibration intensity to set vibrations. Drag the sliders to set the vibration  
intensity for:  
l
Incoming call  
Settings  
150  
   
l
l
Notification  
Haptic feedback  
3. Tap OK to save the settings.  
Ringtones  
Choose a ringtone for incoming calls.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Ringtones to choose a ringtone:  
l
Tap a ringtone to select it. As you tap a ringtone, a sample plays.  
l
Tap Add to choose a music track from Google Music, a sound file from Dropbox, or use  
Sound picker to choose a song from Music player.  
3. Tap OK to save the setting.  
Vibrations  
Choose vibrations to play for notifications, such as for incoming calls, new messages, and event  
reminders.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Sound > Vibrations to choose a vibration.  
3. Tap a vibration to play a sample and select the vibration, or tap Create to create your own  
pattern.  
4. Tap OK to save the setting.  
Notifications  
Choose a sound for notifications, such as for new messages and event reminders.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Sound > Notifications, and then tap a sound to play a sample and select the sound.  
3. Tap OK to save the setting.  
Settings  
151  
     
Vibrate When Ringing  
When Vibrate when ringing is enabled, a vibration plays for calls and notifications, along with the  
ringtone or sound. You can use the Vibration intensity and Vibrations settings to customize the  
vibration.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap the check box beside Vibrate when ringing to enable or disable  
the option.  
Dialing Keypad Tone  
When Dialing keypad tone is enabled, tones play when you tap keys on the Phone keypad.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap the check box beside Dialing keypad tone to enable or disable  
the option.  
Touch Sounds  
When Touch sounds is enabled, tones play when you tap or touch the screen to make selections.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap the check box beside Touch sounds to enable or disable the  
option.  
Screen Lock Sound  
When Screen lock sound is enabled, tones play when you touch the screen to lock or unlock it.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap the check box beside Screen lock sound to enable or disable  
the option.  
Settings  
152  
       
Haptic Feedback  
When Haptic feedback is enabled, vibration plays when you tap the Menu and Back keys, and for  
certain screen touches.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap the check box beside Haptic feedback to enable or disable the  
option.  
Emergency Tone  
You can choose to have a tone play, or have your phone vibrate, periodically during an emergency  
call.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap Emergency tone to select a tone:  
Off: No tone or vibration plays during emergency calls.  
Alert: A tone plays during emergency calls.  
l
l
l
Vibrate: A vibration plays during emergency calls.  
Samsung Keyboard Sound Settings  
You can choose whether sounds and vibrations play when you tap keys on the Samsung Keyboard  
while entering text.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound, and then tap an option to enable or disable it:  
l
Sound when tapped: When enabled, a sound plays when you tap keys.  
Vibrate when tapped: When enabled, a vibration plays when you tap keys.  
l
Samsung Applications Sound Settings  
You can configure options for sound used in Samsung apps.  
Settings  
153  
       
Call Sound Settings  
Configure sounds your phone makes during phone calls.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Call, and then configure sounds:  
l
Call alerts: Choose whether tones or vibration play for certain stages when making phone  
calls.  
o
Vibrate on connection to network: When enabled, your phone will vibrate when a call  
connects to the network.  
o
Call-end vibration: When enabled, the phone vibrates when the other caller ends the  
call.  
o
Call connect tone: When enabled, the phone plays a tone when the other caller  
answers a call.  
o
Minute minder: When enabled, a tone plays once per minute during a call.  
o
Call end tone: When enabled, the device plays a tone when the other caller ends the  
call.  
o
Alerts on call: When enabled, notifications for alarms and new messages play during  
calls. When disabled, these notifications will be muted during a call.  
l
Ringtones and keypad tones: Choose tones and/or vibration to play for incoming call  
notifications.  
o
Ringtones: Select a ringtone for incoming calls. Tap OK to save your selection.  
o
Vibrations: Select a vibration pattern to play for incoming calls when the Vibrate when  
ringing option is enabled. You can tap Create to create a custom pattern. Tap OK to  
save the settings.  
o
Vibrate when ringing: Play a vibration for incoming calls. The vibration pattern is set at  
the Vibrations setting.  
o
Dialing keypad tone: Enable or disable tones for keypad taps.  
l
l
Personalize call sound: Choose options to adapt sound to your preferences. This option  
can only be configured when on a call. For more details, see In-call Options.  
Noise reduction: When enabled, your phone uses noise reduction to minimize background  
noise during calls.  
Messages Sound Settings  
Configure sounds your phone uses for messages.  
Settings  
154  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Messages to configure sounds:  
l
Tap the ON/OFF switch to turn Messages sounds on or off. Sounds must be turned on to  
configure settings.  
l
l
Notification sound: Choose a ringtone for message notifications.  
Vibrate: Enable or disable vibration, to play along with the ringtone for message  
notifications. If you have enabled Vibrations for setting, Vibrate for messages will also be  
enabled.  
l
Repeat message alert: Choose how often your phone notifies you of new message(s).  
Email Sound Settings  
Configure sounds your phone uses for emails.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Email, and then configure sounds:  
l
Priority senders: Choose sounds to use for email notifications from priority senders. You  
can configure a list of priority senders in the Email app settings.  
o
Email notifications: When enabled, an icon displays in the Status bar when you  
receive new emails from priority senders.  
o
Notification sound: Choose a ringtone to play for notifications for new email from  
priority senders.  
o
Vibrate: When enabled, vibration plays for notifications for new email from priority  
senders.  
l
Tap an email account to choose sounds to use for email notifications for a specific account.  
o
Email notifications: When enabled, an icon displays in the Status bar when you  
receive new emails notifications for a specific account.  
o
Notification sound: Choose a ringtone to play for notifications for new email  
notifications for a specific account.  
o
Vibrate: When enabled, vibration plays for notifications for new email notifications for a  
specific account.  
Calendar Sound Settings  
Configure sounds your phone uses for the Calendar.  
Settings  
155  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Sound > Calendar, and then configure sounds:  
l
l
l
Select alert type: Choose how you want your phone to alert you to Calendar events.  
Notification sound: Choose a ringtone to play for notifications for Calendar notifications.  
Vibration: When enabled, vibration plays for notifications for new email for Calendar  
notifications.  
Music Effects  
Choose effects to apply when playing music on your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Sound > Music effects, and then choose a control panel for music effects.  
Display Settings  
Configure settings for your phone’s display.  
Brightness  
Adjust the screen brightness to suit your surroundings, or to your personal preference. You may also  
want to adjust screen brightness to conserve battery power.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display > Brightness to configure options:  
l
Tap the checkmark beside Automatic brightness to allow the phone to adjust brightness  
automatically.  
l
To set a custom brightness level, clear the Automatic brightness checkmark and then touch  
and drag the Brightness level.  
3. Tap OK to save the settings.  
Settings  
156  
     
Font  
You can set the font style and size for all text that displays on the screen.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Display > Font to choose a Font style and Font size.  
Tip: Tap Download to find new fonts from Google Play Store.  
Screen Rotation  
When Screen rotation is turned on, the screen automatically updates when you rotate the phone.  
See Rotate for more information. You can also choose to enable Smart rotation, to have your phone  
use the front camera to check the orientation of your face to the screen, and adjust the screen  
automatically.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display > Screen rotation for options:  
l
Tap the ON/OFF switch beside Screen rotation to turn the option on or off.  
l
Tap the checkbox beside Smart rotation to enable or disable the options. When enabled,  
the phone will automatically rotate the screen based on the orientation of your face to the  
screen.  
Smart Stay  
When Smart stay is enabled, your phone uses the front camera to detect your face, and will not time  
out as long as you are facing the screen.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Display and then tap the check box beside Smart stay to enable or disable the option.  
Screen Timeout  
Screen timeout lets you choose how long the display screen remains lit after you touch the screen or  
press any key.  
Settings  
157  
       
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Display > Screen timeout, and then choose a time period.  
Screen Mode  
Choose a screen mode to match your type of viewing. You can choose to have the phone  
automatically adapt the display depending on the type of image being displayed, and other criteria  
such as battery level.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display > Screen mode, and then choose a mode:  
l
To have your phone automatically optimize the display to match the type of image being  
displayed and other criteria, such as battery level, enable Adapt display.  
l
To choose a specify type of display, enable Dynamic, Standard, Professional photo, or  
Cinema.  
3. Tap Save.  
Auto Adjust Screen Tone  
When Auto adjust screen tone is enabled, your phone analyzes the images displayed on the screen  
and automatically adjusts the brightness to conserve battery power.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display, and then tap the check box beside Auto adjust screen tone to enable or  
disable the option.  
Daydream  
The Daydream setting controls what the screen displays when the phone is docked, or while  
charging. You can choose to display colors, or display photos stored on your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display > Daydream, and then tap the ON/OFF switch beside Daydream to turn the  
option on or off. When on, you can configure these options:  
l
Colors: Tap the selector to enable or disable display of a colorful screen.  
Settings  
158  
       
l
l
l
Flipboard: Display pictures from Flipboard. After enabling the option, tap  
pictures to display.  
to choose  
Google Photos: Display pictures from Google Photos. After enabling the option, tap  
choose pictures to display.  
to  
Photo frame: Display pictures in a photo frame. After enabling the option, tap  
pictures to display.  
to choose  
to  
l
l
Photo table: Display of pictures in a photo table. After enabling the option, tap  
choose pictures to display.  
Tap Preview to see a demonstration of Daydream.  
LED Indicator Settings  
The LED indicator on the front of the device displays when the device is locked, to notify you of status  
changes and events. Use LED indicator settings to configure how the LED functions.  
Note: The LED indicator only displays when the screen is locked.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Display > LED indicator, and then tap the check box beside options to enable or  
disable the option:  
l
Charging: When enabled, the LED glows red during charging, and green when the battery  
is fully charged.  
l
l
Low battery: When enabled, the LED blinks red to indicate low battery charge.  
Notifications: When enabled, the LED blinks blue to show that you have missed calls, new  
messages, or application events.  
l
Voice recording: When enabled, the LED blinks blue when recording with the screen  
turned off.  
Touch Key Light Duration  
This feature allows you to set the length of time  
them.  
Recent and  
Back remain lit after you touch  
Settings  
159  
   
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Display, and then tap Touch key light duration to choose a timeout period.  
Increase Touch Sensitivity  
When enabled, the sensitivity of the touch screen is increased, to improve results when using an  
optional touch pen (not included), or when wearing gloves.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Display, and then tap Increase touch sensitivity to enable or disable the option.  
Wallpaper Settings  
Customize the background of the home and Lock screens.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Wallpaper, and then choose a screen to customize, from Home screen, Lock  
screen, or Home and lock screens.  
3. Scroll the options to choose a wallpaper, or choose another source:  
l
More images: Select a picture from Gallery, Dropbox, or Photos. Follow the prompts to crop  
the picture and save it as wallpaper.  
l
l
l
Live wallpapers: Select a moving scene for the background.  
Travel wallpaper: Display travel destinations on the screen.  
ID Wallpapers: Choose an image from the ID wallpapers included with your phone.  
Lock Screen Settings  
Configure settings for locking the screen, to improve security.  
Screen Lock  
Choose a screen lock, to secure the screen. Depending on the Screen lock you choose, you can  
also choose screen lock options to work along with the screen lock.  
Settings  
160  
       
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Lock screen > Screen lock, and then select a screen lock option.  
Set a Swipe Screen Lock  
When a Swipe screen is set, you swipe your finger across the screen to unlock the device.  
This is the default screen lock on your phone, and offers no security, but you can set special lock  
screen options.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Lock screen > Screen lock > Swipe.  
3. When you have a Swipe screen lock set, you can also configure these options:  
l
Dual Clock: When turned on, Dual clock displays the time in your home city, and in your  
current location, when your phone is roaming. Tap the ON/OFF switch to turn Dual clock on  
or off, and then tap Set home city to choose your home time zone.  
l
l
l
Clock size: Choose the size of clock displayed on the lock screen.  
Show date: Enable or display the display of the current date on the lock screen.  
Camera shortcut: When enabled, a shortcut to Camera displays on the lock screen. You  
can drag the Camera shortcut to unlock the screen and launch the Camera in one step. Note  
that Camera is the only app you can access with this method; you’ll need to enter your  
screen unlock to unlock the screen.  
l
l
l
l
Owner information: Enter owner information text, and then tap the checkbox to control  
whether it displays on the lock screen.  
Unlock effect: You can choose an effect to display on the screen when you touch it without  
swiping to unlock.  
Additional information: Choose whether to display weather information or information  
from S Health when Walking mode is enabled in the S Health app.  
Help text: When enabled, your phone displays helpful hints on the lock screen.  
Set a Pattern Screen Lock  
When a Pattern screen lock is set, you draw a pattern, which you create, on the screen to unlock the  
device. You will also set a PIN to use as a backup, in case you forget the pattern.  
Settings  
161  
   
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Lock screen > Screen lock > Pattern, and then follow the prompts to create or  
change your screen unlock pattern.  
3. When you have a Pattern screen lock set, you can also configure these options:  
l
Dual Clock: When turned on, Dual clock displays the time in your home city, and in your  
current location, when your phone is roaming. Tap the ON/OFF switch to turn Dual clock on  
or off, and then tap Set home city to choose your home time zone.  
l
l
l
l
Clock size: Choose the size of clock displayed on the lock screen.  
Pattern type: Choose the type of pattern to display.  
Show date: Enable or display the display of the current date on the lock screen.  
Camera shortcut: When enabled, a shortcut to Camera displays on the lock screen. You  
can drag the Camera shortcut to unlock the screen and launch the Camera in one step. Note  
that Camera is the only app you can access with this method; you’ll need to enter your  
screen unlock to unlock the screen.  
l
l
l
l
l
Owner information: Enter owner information text, and then tap the checkbox to control  
whether it displays on the lock screen.  
Additional information: Choose whether to display weather information or information  
from S Health when Walking mode is enabled in the S Health app.  
Make pattern visible: When enabled, your pattern will display on the screen briefly as you  
draw it.  
Vibration feedback: When enabled, your phone will vibrate if you draw the incorrect  
pattern.  
Lock automatically: Choose whether the screen will lock automatically immediately after  
the screen turns off (dims), or choose a time interval to delay locking. During the time  
interval, your phone will still be unlocked, but the screen will be dim.  
l
Lock instantly with power key: When enabled, pressing the Power/Lock key locks the  
screen instantly.  
Set a Fingerprint Screen Lock  
With a Fingerprint screen lock, you can use your fingerprint to unlock the screen, or for other  
purposes you decide. Fingerprint recognition provides a lower level of security than a password.  
Follow the onscreen instructions to register your fingerprint. If other apps support the use of your  
fingerprint for security, you can select that option in the app.  
Settings  
162  
 
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Lock screen > Screen lock > Fingerprint, and then follow the prompts to register  
your fingerprints. You must swipe the pad of your finger across the Home key multiple times, to  
allow your phone to store your fingerprint.  
3. When you have a Fingerprint screen lock set, you can also configure these options:  
l
Dual Clock: When turned on, Dual clock displays the time in your home city, and in your  
current location, when your phone is roaming. Tap the ON/OFF switch to turn Dual clock on  
or off, and then tap Set home city to choose your home time zone.  
l
l
l
Clock size: Choose the size of clock displayed on the lock screen.  
Show date: Enable or display the display of the current date on the lock screen.  
Camera shortcut: When enabled, a shortcut to Camera displays on the lock screen. You  
can drag the Camera shortcut to unlock the screen and launch the Camera in one step. Note  
that Camera is the only app you can access with this method; you’ll need to enter your  
screen unlock to unlock the screen.  
l
l
l
Owner information: Enter owner information text, and then tap the checkbox to control  
whether it displays on the lock screen.  
Additional information: Choose whether to display weather information or information  
from S Health when Walking mode is enabled in the S Health app.  
Lock automatically: Choose whether the screen will lock automatically immediately after  
the screen turns off (dims), or choose a time interval to delay locking. During the time  
interval, your phone will still be unlocked, but the screen will be dim.  
l
Lock instantly with power key: When enabled, pressing the Power/Lock key locks the  
screen instantly.  
Set a PIN Screen Lock  
With a PIN screen lock, you enter a Personal Identification Number, which you create, on the screen  
to unlock the device.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Lock screen > Screen lock > PIN, and then follow the prompts to create or change  
your screen unlock PIN.  
3. When you have a PIN screen lock set, you can also configure these options:  
l
Dual Clock: When turned on, Dual clock displays the time in your home city, and in your  
current location, when your phone is roaming. Tap the ON/OFF switch to turn Dual clock on  
Settings  
163  
 
or off, and then tap Set home city to choose your home time zone.  
Clock size: Choose the size of clock displayed on the lock screen.  
Show date: Enable or display the display of the current date on the lock screen.  
l
l
l
Camera shortcut: When enabled, a shortcut to Camera displays on the lock screen. You  
can drag the Camera shortcut to unlock the screen and launch the Camera in one step. Note  
that Camera is the only app you can access with this method; you’ll need to enter your  
screen unlock to unlock the screen.  
l
l
l
Owner information: Enter owner information text, and then tap the checkbox to control  
whether it displays on the lock screen.  
Additional information: Choose whether to display weather information or information  
from S Health when Walking mode is enabled in the S Health app.  
Lock automatically: Choose whether the screen will lock automatically immediately after  
the screen turns off (dims), or choose a time interval to delay locking. During the time  
interval, your phone will still be unlocked, but the screen will be dim.  
l
Lock instantly with power key: When enabled, pressing the Power/Lock key locks the  
screen instantly.  
Set a Password Screen Lock  
With a Password screen lock, you enter an alphanumeric password, which you create, on the  
screen to unlock the device.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Lock screen > Screen lock > Password, and then follow the prompts to create or  
change your screen unlock password.  
3. When you have a PIN screen lock set, you can also configure these options:  
l
Dual Clock: When turned on, Dual clock displays the time in your home city, and in your  
current location, when your phone is roaming. Tap the ON/OFF switch to turn Dual clock on  
or off, and then tap Set home city to choose your home time zone.  
l
l
l
Clock size: Choose the size of clock displayed on the lock screen.  
Show date: Enable or display the display of the current date on the lock screen.  
Camera shortcut: When enabled, a shortcut to Camera displays on the lock screen. You  
can drag the Camera shortcut to unlock the screen and launch the Camera in one step. Note  
that Camera is the only app you can access with this method; you’ll need to enter your  
screen unlock to unlock the screen.  
Settings  
164  
 
l
l
l
Owner information: Enter owner information text, and then tap the checkbox to control  
whether it displays on the lock screen.  
Additional information: Choose whether to display weather information or information  
from S Health when Walking mode is enabled in the S Health app.  
Lock automatically: Choose whether the screen will lock automatically immediately after  
the screen turns off (dims), or choose a time interval to delay locking. During the time  
interval, your phone will still be unlocked, but the screen will be dim.  
l
Lock instantly with power key: When enabled, pressing the Power/Lock key locks the  
screen instantly.  
Multi Window Settings  
Multi window allows you to use two apps on the same screen, in separate, resizable windows. For  
more information, see Multi Window.  
After you turn on Multi window in Settings, you can control whether the Multi window tab displays on  
the screen by touching and holding  
Back.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Multi window, and then tap the ON/OFF switch beside Multi window to enable or  
disable the option.  
l
Tap the check box beside Open in multi window view to display content in Multi window  
automatically, when you open files from My Files or Video, or attachments from emails and  
messages.  
Notification Panel Settings  
Configure options for the Notification panel, available when you swipe your finger down from Status  
bar at the top of the screen.  
At the top of the Notification panel, you can control settings with the Quick settings. Choose the quick  
settings to display in Notification panel settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Notification panel to configure settings:  
l
Brightness adjustment: Tap the check box to display a slider for adjusting the screen  
brightness on the notification panel.  
Settings  
165  
   
l
Recommended apps: When on, your phone will display a selection of app icons on the  
Notification panel, according to your actions. For example, when you connect a headset,  
Music and other entertainment apps will display. Tap the ON/OFF switch to turn the option  
on, and then tap Edit to choose apps to display.  
l
Set quick setting buttons: Quick setting buttons display at the top of the Notification panel,  
to allow you to set favorite options quickly.  
o
Tap buttons to add or hide the button from the Notification panel.  
o
Touch and hold a button, and then drag it into a new position in the list.  
Toolbox  
Toolbox is a floating shortcut menu that displays on every screen, so you can access your favorite  
apps quickly. You can choose items to display in Toolbox, and you can drag the Toolbox anywhere  
on the screen.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Toolbox to configure settings:  
l
Tap the ON/OFF switch to turn Toolbox on or off. Toolbox must be turned on to configure  
settings.  
l
Tap Edit to choose up to five apps to display in Toolbox.  
Use the Toolbox  
When Toolbox is turned on, you can use these options:  
n
To access a toolbox app, tap  
Toolbox , and then tap the app you want to run.  
n
To reposition Toolbox, touch and hold on  
the screen.  
Toolbox, and then drag it to another position on  
n
n
To turn Toolbox off, touch and hold on  
Toolbox, and then drag it to the Delete icon.  
To quickly access Toolbox settings, touch and hold on  
icon.  
Toolbox, and then drag it to the Edit  
Settings  
166  
 
One-handed Operation Settings  
When One-handed operation is turned on, you can swipe the edge of all screens to adjust the scale  
and position of the screen. This can be useful when using your phone with one hand – you can move  
the screen closer to your hand.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
One-handed operation.  
l
Tap the ON/OFF switch beside One-handed operation to turn the option on or off.  
l
Follow the onscreen instructions to set up your screen. For easy right-hand access, swipe  
from the right side of the screen, to the middle, and then back to the right. For left-hand use,  
swipe from the left side, to the middle, and then back to the left.  
Easy Mode Settings  
Easy mode provides an simpler experience using your phone, with a simpler home screen layout  
and simpler app interactions. If you’re a first-time smartphone user, or just to want to simplify the  
operation of your phone, you can turn on Easy mode at any time.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Easy mode to configure options:  
l
Tap the button beside Easy mode to enable or disable the option. Easy mode must be  
enabled to set other options.  
l
Easy applications: Choose apps, to apply Easy mode to their operation.  
3. Tap Done to apply your Easy mode settings.  
Accessibility Settings  
Your device offers features to make using the device easier for those with certain physical  
disabilities. Use Accessibility settings to configure these features.  
Configure Vision Accessibility Settings  
Your phone offers many features to assist users who are blind or low-vision.  
Settings  
167  
       
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessibility > Vision to configure options:  
l
TalkBack: Enable or disable the TalkBack feature and configure options. When TalkBack is  
on, your device speaks descriptions of items you touch or activate on your phone, to help  
blind and low-vision users. When TalkBack is turned on, you may need to use a double-tap  
to select items, because a single tap is used to trigger TalkBack. Tap the ON/OFF switch  
beside TalkBack to turn the feature on or off. When TalkBack is on, tap Settings to configure  
specific options.  
l
l
Dark screen: When TalkBack is on, you can enable Dark screen to keep your phone’s  
screen turned off at all times. When Dark screen is enabled, double-press the Power/Lock  
key to turn it on or off while using your phone.  
Rapid key input: When TalkBack is on, you can enable Rapid key input, to allow you to  
release your finger to enter a selection, instead of double-tapping it. By default, when you  
have TalkBack turned on, you must double-tap items on the screen to select them. If you turn  
on Rapid key input, you can tap and release your finger to select and item instead of double-  
tapping.  
l
Speak passwords: When Explore by touch is turned on, you can enable Speak passwords  
to have your phone read out characters entered in password fields.  
NOTE: Use caution with this feature, because others near you will be able to hear your  
passwords.  
l
l
Font size: Choose the size of text for your phone’s screens.  
Magnification gestures: When turned on, you can use special magnification gestures,  
including:  
o
Triple-tap on most screens to zoom in or out.  
o
While zoomed in, you can drag two or more fingers across the screen to pan (move  
around the screen).  
o
While zoomed in, you can use pinch with two fingers to adjust the zoom level. Move your  
fingers closer together to zoom in, or apart to zoom out.  
o
Triple-tap and hold to temporarily magnify what’s under your finger. You can then drag  
your finger across the screen to explore the screen. Lift your finger to return to the  
regular-size screen.  
l
l
Notification reminder: When turned on, your phone beeps at set intervals to remind you of  
unread notifications. Tap the ON/OFF switch beside Notification reminder to turn the option  
on, and then tap Reminder interval to set the interval for reminder beeps.  
Negative colors: When enabled, screen colors are reversed.  
Settings  
168  
l
l
Color adjustment: When turned on, you can adjust the color of the screen if you have  
difficulty reading the screen because of the color. Follow the prompts to fine-tune screen  
colors.  
Accessibility shortcut: When turned on, you can quickly turn on accessibility features by  
performing a special gesture:  
o
Press and hold the Power/Lock key until you hear a sound or feel a vibration, and then  
press and hold with two fingers until you hear an audio confirmation.  
l
Text-to-speech options: Configure options for converting text to speech. For more  
information, see Text-to-speech Options.  
Configure Hearing Accessibility Settings  
Your phone offers many features to assist users who are deaf or hearing-impaired.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessibility > Hearing to configure options:  
l
Flash notification: When enabled, your phone blinks the Camera flash for notifications.  
l
Turn off all sounds: When enabled, every sound made by the phone during taps,  
selections, notifications, etc. is muted.  
l
l
Hearing aids: When enabled, your phone automatically adjusts to attempt to improve the  
sound quality for use with hearing aids.  
Samsung subtitles (CC): When turned on, your phone displays Samsung subtitles where  
available. Tap the ON/OFF switch to turn the option on or off, and then tap Samsung  
subtitles to configure options.  
l
Google subtitles (CC): When turned on, your phone displays Google subtitles where  
available. Tap the ON/OFF switch to turn the option on or off, and then tap Google subtitles  
to configure options like Language, Text size, and Caption style.  
l
l
Sound balance: Adjust the sound sent to the left and right when using earphones.  
Mono audio: Enable or disable the compression of stereo audio into a single mono audio  
stream for use with a single earphone.  
l
Baby crying detector: When turned on, your phone will vibrate when it detects a baby  
crying. Tap the ON/OFF switch to turn the feature on or off. When turned on, you can tap  
Menu to configure options:  
o
Recent alerts: Display a list of recent detector alerts.  
Settings  
169  
 
o
Settings: Choose options for the vibration alert your phone plays when it detects a  
crying baby. You can set the pattern and intensity of the vibration, and enable or disable  
flash notification, to have your phone also flash the camera light.  
l
Auto haptic: When enabled, your device automatically vibrates in response to the sounds of  
downloadable apps, such as games. Not all apps support this feature.  
Configure Dexterity and Interaction Settings  
Your phone offers many features to improve accessibility related to the way you interact with touch  
and movement.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessibility > Dexterity and interaction to configure options:  
l
Assistant menu: Assistant menu can improve device accessibility by providing quick  
access to important functions.  
When turned on, a shortcut  
menu.  
appears on all screens to give you access to the Assistant  
Tap Assistant menu to configure options:  
o
Tap the ON/OFF switch beside Assistant menu to turn the feature on or off. When you  
turn on Assistant menu, Single tap mode is also enabled.  
o
Dominant hand: Choose whether the Assistant menu displays on the left or right side of  
the screen  
o
Edit: Re-order or remove items from the Assistant menu.  
o
Assistant plus: When turned on, Assistant plus displays contextual menu options for  
some apps in Assistant menu. Not all apps support this option. Tap Assistant plus, and  
then tap the ON/OFF switch to turn the option on or off. After you turn on Assistant plus,  
enable or disable apps to use with Assistant plus.  
o
Touchpad size: Choose a size for touchpads for use in your phone’s screens.  
o
Cursor size: Choose the size of cursors, to display on the screen.  
o
Cursor speed: Choose a speed for cursor blinks.  
l
l
Air wake up: When turned on, you can move your hand over the screen to turn it on, if the  
phone is face up on a stable surface. Tap the ON/OFF switch to turn the option on or off.  
Smart scroll: When turned on, your phone uses the front camera to recognize the  
movements of your head, to control scrolling on the screen. You can scroll through Web  
Settings  
170  
 
pages and email messages by tilting your head or the phone, while looking at the screen. Not  
all apps support this feature.  
o
Tap the ON/OFF switch to turn the option on or off, and then configure options.  
o
Tilting head: When enabled, your phone scrolls when you tilt your head while looking at  
the screen.  
o
Tilting device: When enabled, your phone scrolls when you tilt the device while looking  
at the screen.  
o
Speed: Set the speed of scrolling with Smart scroll.  
o
Visual Feedback display: When enabled, an icon displays when using Smart scroll.  
l
l
Press and hold delay: Choose how long your phone waits during a tap and hold gesture  
on the screen, before continuing with the tap and hold action.  
Interaction control: Control how your phone interprets motions and screen touches. To  
turn Interaction control on or off at any time, press and hold the Home key and the down  
Volume key at the same time. When Interaction control is on, you can use motions to control  
your phone, and screen timeout is turned on. You can also block areas of the screen from  
touch interaction. Automatic screen rotation and hard-key functions (Power/Lock key,  
Volume key, etc.) will be turned off, and app notifications will only be shown in the  
Notification panel and status bar.  
Configure Other Accessibility Settings  
Your phone offers many features to improve device accessibility .  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessibility to configure options:  
l
Direct access: When turned on, you can access common accessibility settings from any  
screen by pressing the Home key rapidly 3 times in a row. Tap the ON/OFF switch to turn the  
feature on, and then enable or disable options to display with direct access.  
l
Answering and ending calls: Select options for answering and ending calls.  
o
Answer calls by: You can choose to answer calls by pressing  
Home, with voice  
commands, by waving your hand over the device, or by bringing the device to your ear.  
o
End calls by: You can choose to end calls by pressing the Power/Lock key.  
l
Single tap mode: When enabled, you can use a single tap to dismiss or snooze alarms,  
notifications and alerts, and answer or reject calls.  
Settings  
171  
 
l
Manage accessibility: Choose settings for exporting, updating, and sharing the  
accessibility settings as a file.  
Configure Accessibility Services  
If you have installed any accessibility-related services on your phone, you can access their settings  
from the main Accessibility settings menu.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessibility.  
l
Services you have installed display under the Services heading.  
Blocking Mode Settings  
When Blocking mode is turned on, notifications for selected features are blocked, and you only  
receive the notifications you choose. You can choose to block notifications by feature or contact, and  
choose blocking all the time, or during a specific time period.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Blocking mode to configure options:  
l
Tap the ON/OFF switch beside Blocking mode to enable or disable the setting. Blocking  
mode must be turned on to configure options.  
l
l
l
Block incoming calls: When enabled, notifications for incoming calls will not display.  
Turn off notifications: When enabled, notifications for new messages will not display.  
Turn off alarm and timer: When enabled, notifications for alarms and timers will not  
display.  
l
Set a time for blocking mode:  
o
Tap the check box beside Always, to block notifications at all times.  
o
To set a specific time period to block notifications each day, disable the Always option,  
and then set a starting (From field) time and ending time (To field). Tap the time fields  
and then set the time.  
l
Choose an option for blocking by contact:  
o
Tap Allowed contacts, and then choose whether to allow notifications for all contacts,  
just your favorites, or a custom list you create. If you choose a custom list, you’ll be  
Settings  
172  
   
prompted to select contacts for the list.  
o
If you created a Custom list of allowed contacts, you can tap Allowed contact list to  
modify the list of allowed contacts. This option is only available when the Custom list is  
enabled.  
Private Mode Settings  
Private mode secures your personal content and keeps it hidden on your device. Private mode is  
available for certain applications, including Gallery, Video, Music, Voice Recorder, and My files.  
When Private mode is enabled, you can select items you want to mark as private.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Private mode. When you access Private mode the first time, you’ll be prompted to set  
up a secure screen unlock, such as Pattern, PIN, Fingerprint, or Password.  
l
To turn off Private mode, you can use the ON/OFF switch in Settings, or turn it off on the  
Notification panel.  
Finger Scanner  
You can use fingerprint recognition as an alternative to entering passwords.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Finger Scanner to configure options:  
l
l
l
l
Fingerprint manager: Tap to register up to three fingerprint(s).  
Change alternative password: Modify the password you set to back up your fingerprints.  
Screen lock: Select a screen lock. For more information, see Screen Lock.  
Verify Samsung account: You can choose to verify your identity using your fingerprints  
when logging in to your Samsung account. Tap the ON/OFF switch to turn the option on or  
off.  
l
Pay with PayPal: Configure options to link your PayPal account to your device to make  
faster and more secure PayPal payments using any of your registered fingerprints. After  
linking your PayPal account, you have access to special offers from your favorite stores. If  
you do not have a PayPal account, you can sign up for one on your phone.  
o
FIDO Ready™ support: FIDO Ready support must be installed before you can link  
your PayPal account. Tap Install, and then follow the onscreen instructions to install the  
Settings  
173  
   
application.  
o
PayPal account: After you install FIDO Ready support, tap Link to link your PayPal  
account to your phone and fingerprint.  
Motions and Gestures Settings  
The Motion settings allow you to set up various Motion activation services.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Motions and gestures to configure features. Tap the ON/OFF switch to turn a feature  
on or off. When a feature is on, tap the feature name to configure options:  
l
Air browse: When on, you can scroll between items like pictures, pages, or music tracks by  
moving your hand up and down, or left and right above the screen. Tap the ON/OFF switch  
to turn the feature on, and then configure options:  
o
The body of emails: When enabled, you can use air browse to scroll through the body  
of emails.  
o
Gallery: When enabled, you can use air browse to move between pictures in Gallery  
o
Internet: When enabled, you can use air browse to scroll through a Web page and move  
between open windows in the Internet app.  
o
Music: When enabled, you can use air browse to change music tracks on the Music  
screen.  
o
Music on lock screen: When enabled, you can use air browse to change music tracks  
on the lock screen.  
l
l
Direct call: When on, you can lift the device to your ear while viewing a contact to call the  
contact. Tap the ON/OFF switch to turn the feature on or off.  
Smart alert: When on, you can lift the phone to receive notifications of missed calls and  
notifications that occurred while the device was stationary. Tap the ON/OFF switch to turn  
the feature on or off.  
l
Mute/pause: When on, you can mute incoming calls and pause playback by turning the  
phone screen-side down. Tap the ON/OFF switch to turn the feature on, and then configure  
options:  
o
Covering screen with hand: When enabled, covering the screen with your hand will  
mute the ring of incoming calls and alarms, and pause media playback.  
o
Turning device over: When enabled, turning the device screen-down will mute the ring  
of incoming calls, and pause music playback  
Settings  
174  
 
o
Smart pause: when enabled, your phone use the front camera to detect if you are facing  
the screen, and will pause video playback when you look away.  
l
Palm swipe to capture: When on, you can save a copy of the current screen to the  
clipboard by swiping the side of your hand across the screen. Tap the ON/OFF switch to turn  
the feature on or off.  
Air View Settings  
With Air View, you can preview information, extend text selection, or enlarge pictures by hovering  
your finger over the screen. For example:  
n
n
n
Calendar: See more details by hovering your finger over an events.  
Gallery: View the pictures in an album by hovering your finger over the album.  
Video player: Preview a scene or show the elapsed time by hovering your finger over the  
progress bar.  
n
Phone: Preview the contacts assigned to speed dial numbers by hovering your finger over the  
keypad.  
To set your Air View options:  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Air view, and then tap the ON/OFF switch to turn the feature on or off.  
Accounts Settings  
When you set up accounts on your phone, such as your Google or Samsung accounts, and your  
email or social networking accounts, you can synchronize account information between your phone  
and the account. Types of information you can synchronize include contacts, pictures, videos, and  
other types of files.  
You can also set up options for backing up information from your phone to the cloud, and back up or  
reset your device.  
Add an Account  
Add an account to your phone to share information between your phone and the account.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Accounts > Add account, and then choose a type of account.  
Settings  
175  
   
3. Follow the prompts to enter your account credentials and complete the account set up.  
Manage Existing Accounts  
1.  
2.  
3.  
From home, tap  
Tap Accounts, and then tap an existing account.  
Select available settings from the account menu, or tap  
Apps >  
Settings.  
Menu for additional options.  
Cloud Settings  
Set up accounts on your phone to save information from your phone to the account.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Cloud, and then configure options:  
l
Add Samsung account: Sign in to your Samsung account, or create a new Samsung  
account. You can sync contacts, calendar events, memos, and Internet shortcuts. You can  
back up Logs, SMS and MMS messages, and current wallpaper settings.  
l
Link Dropbox account: Sign in to your Dropbox account, or set up a new account, to sync  
pictures, videos and documents.  
Backup and Reset Settings  
Set options for backing up your data to the Google servers.  
Backup and Restore Settings  
You can back up your data to a Google account, and use the backed-up date to restore information  
when you re-install an app, or when you get a new device.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Backup and Reset to configure backup features:  
l
Back up my data: Tap the check box to turn on automatic backup to a Google account, and  
then set up an account for the backups.  
l
Backup account: When Back up my data is turned on, set up a Google account for  
backups. You can set up a new Google account, or sign in to an existing account.  
Settings  
176  
   
l
Automatic restore: When Back up my data is turned on, you can also turn on Automatic  
restore to automatically restore settings and other information from the backup when you  
reinstall an app.  
Factory Data Reset  
When you perform a Factory data reset, all your personal information is erased from the phone, and  
all settings are returned to the factory defaults. All data will be erased, and cannot be recovered. A  
factory data reset also erases the key for decrypting files stored on an optional installed memory  
card, so files on the card cannot be used after the reset.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Backup and Reset > Factory data reset > Reset device > Delete all.  
Language And Input Settings  
Use Language and input settings to choose a default language for your phone’s operations, plus  
settings for text entry and other inputs.  
Choose a Default Language  
Choose the language for operating your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Language and input, and then tap Language to select a language.  
Set a Default Input Method  
The following procedure allows you to select and set the default method you will use when accessing  
the keyboard.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Language and input, and then tap Default to select the default input method.  
Settings  
177  
     
Samsung Keyboard Settings  
The Samsung Keyboard is an onscreen QWERTY keyboard, so you can enter text by “typing” on  
the keyboard. Samsung keyboard is enabled by default, and you can choose options for using it.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap  
beside Samsung keyboard to configure  
these options:  
l
l
Input languages: Choose language(s) for use with Samsung keyboard. When you have  
more than one language enabled, you can slide your finger on the space bar while entering  
text to switch languages.  
Predictive text: Tap the ON/OFF switch to turn predictive text on or off. Predictive text  
suggests words matching your text entries, and optionally, complete common words  
automatically. Tap Predictive text to configure options:  
o
Live word update: When enabled, predictive text automatically updates with popular  
new words.  
o
Personalized data: When enabled, predictive text uses personal language data you  
have entered to make better predictions. Samsung keyboard can collect all the text you  
enter, including personal data and credit card numbers, in order to give better prediction  
results.  
o
Learn from Facebook: When Personalized data is enabled, you can log into Facebook  
to allow your device to learn from your Facebook postings.  
o
Learn from Gmail: When Personalized data is enabled, you can log into Gmail to allow  
your device to learn from your Gmail email.  
o
Learn from Twitter: When Personalized data is enabled, you can log into Twitter to  
allow your device to learn from your Twitter postings.  
o
Learn from Messages: When Personalized data is enabled, you can allow your device  
to learn from your text and multimedia messages.  
o
Learn from Contacts: When Personalized data is enabled, you can allow your device  
to learn from your Contacts entries.  
o
Clear server data: Delete your anonymous information stored on the personalization  
server.  
o
Clear personal data: Remove all personalized data you have entered.  
o
Privacy Policy: Read the privacy policy.  
Settings  
178  
 
l
l
l
Auto replacement: When turned on, predictive text will complete or replace the word you  
are typing with the most probable word when you tap the Space bar or a punctuation mark.  
My shortcuts: Assign text shortcuts to number keys. This option is only available when  
using QWERTY keyboards.  
Auto capitalization: When enabled, predictive text automatically capitalizes words in your  
text based on common usage, such as at the beginning of sentences.  
l
l
Auto spacing: When enabled, predictive text automatically inserts spaces between words.  
Auto punctuate: When enabled, a period and space are automatically entered to end a  
sentence, when you tap the space bar twice.  
l
Keyboard swipe: When enabled, you can enter text by sliding your finger across the keys  
on the keyboard.  
o
None: When enabled, Samsung Keyboard will not accept text entry by swiping.  
o
SwiftKey Flow: When enabled, you can enter text by swiping your finger across the  
keyboard.  
o
Cursor control: When enabled, you can slide your finger across the keyboard to move  
the cursor to begin entering text.  
o
Flick input: When enabled, you can flick your finger upwards on a key to view symbols  
and alternative characters available from the key. Tap a symbol or character to insert it  
into your text.  
l
Key-tap feedback: Enable or disable options for sound or vibration feedback to your  
onscreen keyboard touches.  
o
Sound: When enabled, a sound plays for your key touches.  
o
Vibration: When enabled, a vibration plays for your key touches.  
o
Character preview: When enabled, the character appears in a bubble as you tap keys.  
o
Press and hold delay: Choose a period for the keyboard to wait before interpreting a  
touch as a press and hold.  
l
More settings:  
o
Reset settings: Return settings to the defaults.  
Swype Settings  
Swype is a new way to enter text on touch screens. Instead of touching each key individually, use  
your finger to trace over the letters of a word. For each word, place your finger on the first letter and  
glide to the subsequent letters, lifting on the last letter.  
Settings  
179  
 
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap  
beside Swype to configure these options:  
l
Settings: Set Swype options:  
o
Vibrate on keypress: When enabled, the device vibrates for your Swype touches.  
Sound on keypress: When enabled, the device plays sounds for your Swype touches.  
Pop-up on keypress: When enabled, the characters display briefly as you tap keys.  
o
o
o
Long-press delay: Choose a period for the keyboard to wait before interpreting a touch  
as a press and hold.  
o
o
o
o
o
Show complete trace: When enabled, Swype displays the trace of each word until you  
start the next word.  
Auto-capitalization: When enabled, Swype automatically capitalizes the first word of  
sentences.  
Auto-spacing: When enabled, Swype automatically inserts spaces between words as  
you complete them.  
Next word prediction: When enabled, Swype predicts the next word based on the  
previous word.  
Show Voice key: When enabled, a Voice input key displays on the Swype keyboard.  
l
Themes: Configure options for the look and position of the keyboard.  
o
Portrait keyboard: Choose whether the keyboard extends the full width of the screen,  
or as a smaller keyboard on the left or right.  
o
Landscape keyboard: Choose the location and style of the keyboard when you rotate  
the phone to landscape orientation (on its side).  
o
Keyboard height: Choose how tall the keyboard is, when the phone is in Portrait  
(upright) and Landscape (on its side) position.  
o
Word choice list font size: Set the size of the text for the words Swype suggests as  
you enter text.  
l
My Words: Choose options for customizing Swype based on your text entries.  
o
Backup & Sync: Use Swype Connect to back up your words.  
o
Living Language: When enabled, Swype will automatically update with popular new  
words.  
o
Social integration: Log into your favorite social networking sites to use your entries  
there to update Swype,  
Settings  
180  
o
o
o
Edit my dictionary: Modify words added to Swype.  
Clear language data: Delete all the words you’ve added to the Swype dictionary.  
Contribute usage data: Allow Nuance to collect usage data to provide better text  
prediction.  
o
Cellular data: When enabled, Swype can use your phone’s connection to the wireless  
data network for updates, language downloads, and other Swype Connect features.  
l
l
l
Languages: Choose the current language for Swype, and download new languages to use  
with Swype.  
Gestures: Learn about shortcuts you can use on the keyboard to quickly accomplish  
common tasks.  
Help: Learn about using Swype.  
o
How to Swype: Learn about using Swype.  
o
Show helpful tips: When enabled, tips display on the screen as you enter text.  
o
Version: Tap to see specific version information and Nuance Communications  
copyright.  
l
Updates: Check for updates to Swype, and install them if desired.  
Google Voice Typing Settings  
Google voice typing allows you to speak your entries. When you enable Google voice typing, it’s  
available for use when you touch a field to enter text.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap the check box beside Google voice typing to  
enable or disable the feature.  
3.  
Tap  
beside Google voice typing to configure options:  
l
Choose input languages: Choose language(s) for use with Google voice typing.  
l
Block offensive words: Tap the check box to control whether Google displays words  
generally recognized as offensive.  
l
Offline speech recognition: Download and install speech recognition engines, to allow  
you to use voice input while not connected to the network, such as during Airplane mode.  
Settings  
181  
 
Speech Settings  
Configure options for using your voice to control your phone.  
Voice Search Settings  
Use Voice search to perform Google searches by speaking the criteria.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap Voice search for these options:  
l
l
l
Language: Choose a language for voice searching.  
Speech output: Choose options for speech output.  
Block offensive words: When enabled, words many people find offensive are not shown in  
results of Google voice searches. Offensive words are replaced in results with a placeholder  
(####).  
l
l
l
Hotword detection: When enabled, you can say “OK Google” to launch voice search from  
the search app.  
Offline speech recognition: Download speech recognition, to enable voice input while  
offline.  
Personalized recognition: Enable to have your device improve recognition based on your  
speech.  
l
l
Google Account dashboard: View and manage your collected data.  
Bluetooth headset: When enabled, audio is recorded when using an optional Bluetooth  
headset (not included).  
Text-to-speech Options  
Text-to-speech (TTS) provides audible readout of text, for example, the contents of text messages  
and the Caller ID for incoming calls.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap Text-to-speech options:  
l
Preferred TTS engine: Select Samsung text-to-speech engine, or Google Text-to-  
speech Engine. Tap  
to configure options.  
l
General:  
Settings  
182  
   
o
o
o
Speech rate: Choose a rate for text readouts.  
Listen to an example: Play an example of speech used for readouts.  
Default language status: View the status of language support for voice recognition.  
Read Notifications Aloud  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input > Read notifications aloud to configure options:  
l
Calls from favorite contacts: When enabled, your phone will read out callers’ information  
for incoming calls from contacts marked with a star in Contacts.  
l
l
l
l
Messages from priority senders: When enabled, your phone will read out senders’  
information for new messages from contacts marked with a star in Contacts.  
Emails from priority senders: When enabled, your phone will read out senders’  
information for new emails from contacts marked with a star in Contacts.  
Calendar event info: When enabled, your phone will read out event information for  
Calendar event notifications.  
Alarm info: When enabled, your phone will read out alarm information when an alarm rings.  
Mouse/Trackpad Settings  
This feature allows you to adjust the speed of the Mouse/trackpad.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Language and input, and then tap Pointer speed to set the pointer speed. Tap OK  
to save your selection.  
Date and Time Settings  
By default, your device receives date and time information from the wireless network. When you are  
outside network coverage, you may want to set date and time information manually using the Date &  
time settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Date and time to configure settings:  
Settings  
183  
   
l
Automatic date and time: When enabled, the device takes date and time updates from the  
wireless network.  
l
l
l
Set date: Enter the current date (only available when Automatic date and time is disabled).  
Set time: Enter the current time (only available when the Automatic setting is disabled).  
Automatic time zone: When enabled, the device takes the time zone from the wireless  
network.  
l
Select time zone: Choose your local time zone (only available when the Automatic setting  
is disabled).  
l
l
Use 24-hour format: Set the format for time displays.  
Select date format: Set the format for date displays.  
Safety Assistance  
Safety assistance is intended to help users send a quick notice of their approximate location and  
visual surroundings to the mobile device of an emergency contact chosen in advance.  
Important: This feature is only for your convenience and is not intended as, nor should it be treated  
as, a substitute for emergency calls to the authorities.  
1.  
From home, tap  
Apps >  
Settings.  
2. Tap Safety assistance to configure these options:  
l
l
l
Emergency mode: Save power during an emergency by using a minimal home screen  
layout and limiting the number of usable apps. Touch the ON/OFF switch to turn the option  
on or off.  
Geo News: Get news about extreme weather conditions that may affect you. Touch the  
ON/OFF switch to turn the option on or off. You can enable or disable pop-ups notifications  
as well.  
Send help messages: Send a quick notice of your approximate location and visual/auditory  
surroundings to the mobile phone of the Emergency contact that you have created. Press  
the Power/Lock Key 3 times in a row to send an emergency message to your emergency  
contact: You should still make an emergency call to the appropriate authorities if needed.  
Touch the ON/OFF switch to turn the option on or off. The following additional options are  
available:  
o
Send pictures: Send pictures from the front and rear cameras to your emergency  
contact when you press the Power/Lock Key 3 times in a row.  
o
Send sound recording: Send a sound recording to your emergency contact when you  
press the Power/Lock Key 3 times in a row.  
Settings  
184  
 
l
Manage primary contacts: Create and maintain primary contact information. To use  
Safety assistance, you must have at least one primary contact saved in Contacts. Follow the  
prompts to set up primary contact(s) if you do not already have them.  
Note: Tap  
Menu > Help for more information about using the safety assistance feature.  
Accessories Settings  
Configure your device’s behavior when it is connected to optional accessories (not included).  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Accessories to configure settings:  
l
HDMI: Configure settings when you connect your phone to other devices via an optional  
HDMI cable (not included).  
o
Audio output: Choose a destination for audio output when you connect to devices via  
HDMI cable.  
Battery Settings  
See what’s using battery power.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Battery to view battery usage for apps and services. Tap an item for more information,  
or to configure options for managing power use.  
Show Battery Percentage  
The battery charge level displays as an icon in the notification panel by default. This feature allows  
you to display the battery icon plus the percentage of remaining charge.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Battery, and then tap the check box beside Show battery percentage to enable or  
disable the option.  
Power Saving Settings  
Configure Power saving mode settings to conserve battery power.  
Settings  
185  
     
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Power saving, and then tap a mode to configure settings:  
l
Power saving mode: Tap the ON/OFF switch beside Power saving mode to turn the  
mode on or off. Power saving mode must be turned on to configure settings.  
o
Block background data: When enabled, your phone blocks the transfer of data in the  
background. This may affect the performance of some apps.  
o
Restrict performance: Tap the ON/OFF switch to turn the option on, and then choose  
the types of performance to restrict. Features such as vibration, screen backlight, and  
key backlights consume power.  
o
Grayscale mode: Tap the ON/OFF switch to switch from color screens to grayscale.  
l
Ultra power saving mode: Tap the ON/OFF switch to turn the mode on. When on, your  
phone will conserve power by changing to grayscale screen mode, limiting the number of  
usable apps, turning off mobile data when the screen is off, and turning off connectivity  
features such as Wi-Fi and Bluetooth.  
Storage Settings  
Manage the use of memory resources in your phone’s Device memory, and on an optional installed  
memory card (not included).  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Storage to view information about memory usage, and for other options:  
l
Device memory: View memory usage for the different types of information stored on your  
phone’s memory. Tap an item for more information.  
l
SD card: View memory usage for the different types of information stored on an optional  
installed memory card (not included).  
o
Mount SD card: Prepare an optional installed memory card for use as storage in the  
phone. This option is only available if an optional memory card is installed, and is not  
already mounted. Usually, your phone mounts a memory card as soon as you install it.  
o
Unmount SD card: Prepare an optional installed memory card for safe removal or  
formatting.  
o
Format SD card: Permanently remove all content from an optional installed memory  
card. After formatting, the content cannot be retrieved.  
Note: For details about using an optional memory card, see microSD Card.  
Settings  
186  
 
Security Settings  
Configure options for securing information on your phone.  
Encryption  
You can encrypt accounts, settings, downloaded apps and their data, media, and other files. After  
encryption, you must enter the PIN or password you set each time you turn on your phone. You can  
also encrypt information stored on an optional installed memory card (not included).  
Encryption may take an hour or more to complete. Start with a charged battery, and keep the device  
on the charger until encryption is complete. Interrupting the encryption process may result in the loss  
of some or all data.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Security, and then tap an option:  
l
Encrypt device: Tap Set screen lock type to start, and then follow the prompts to encrypt  
information.  
l
Encrypt external SD card: Tap Set screen lock type to start, and then follow the  
prompts to encrypt information on an optional installed memory card (not included).  
Tip: To perform encryption, your battery must be charged to at least 80%. It’s best to plug your  
phone in and leave it charging during the encryption process.  
Passwords  
Use the Make passwords visible setting to briefly display password characters as you enter them  
into password fields.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Security, and then tap the check box beside Make passwords visible to enable or  
disable the setting.  
Device Administration  
Some applications, such as Corporate email, may require you allow access to your device by device  
administrators in certain circumstances, such as if your device is lost or stolen.  
Settings  
187  
       
Some features a device administrator might control include:  
n
n
n
Setting the number of failed password attempts before the device is restored to factory settings.  
Automatically locking the device.  
Restoring factory settings on the device.  
Configure Device Administration Options  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Security, and then tap an option:  
l
Device administrators: Tap to view, enable, or disable device administrators.  
o
Android Device Manager: When enabled, Android Device Manager can lock or erase  
a lost device.  
l
l
Unknown sources: Tap the check box to enable or disable your phone’s ability to install  
apps from sources other than Google Play Store.  
Verify apps: Tap the check box to enable or disable a warning before installing apps that  
may cause harm.  
Security Update Service  
Choose options for updating your phone’s security policy.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Security, and then tap an option:  
l
Security policy updates: When enabled, your phone will automatically check for changes  
to the security policy and download any updates, to improve security and service.  
o
Tap the check box beside Automatic updates to enable or disable automatic updating  
of the security policy when connected to preferred networks.  
o
Tap Preferred networks to select an option for downloading security updates.  
o
To manually check for updates, tap Check for updates.  
l
Send security reports: When enabled, your phone will only send security reports to  
Samsung when it is connected to a Wi-Fi network.  
Settings  
188  
 
Credential Storage  
You can install credentials from an optional installed memory card (not included), and use the  
Credential storage settings to allow applications to access the security certificates and other  
credentials.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Security, and then tap an option:  
l
Storage type: Select a storage type to store data in key-value pairs, on the device memory,  
in a private database, or your own network server.  
l
l
Trusted credentials: Tap to view credentials you’ve installed.  
Install from phone storage: Tap to install encrypted certificates from an optional installed  
memory card (not included).  
l
Clear credentials: Tap to clear stored credentials and reset the password (only available  
when credentials are installed).  
Help  
Learn about using your phone.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Help, and then tap topics to display information.  
Activate This Device  
Connect to the network and activate your device. If your device is already activated, use this option  
to view information about your plan and usage.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Activate this device, and then follow the prompts to activate your device on the  
network.  
Settings  
189  
     
System Update Settings  
Use System update options to update your phone’s software.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
System Update to use these options:  
l
Update now: Tap to check for updates, and install them if desired.  
l
Auto update: Enable or disable automatic checking for security updates. You can still  
choose whether to install updates.  
l
l
l
Wi-Fi only: When enabled, your phone will only download updates when connected to a Wi-  
Fi network.  
Update PRL: Download the latest Preferred Roaming List (PRL), used by your phone to  
access the network.  
Update Profile: Update the user profile related to your wireless service account. If you  
choose to change your user name online, use this option to update the user name on your  
phone.  
l
UICC Unlock: Unlock your device’s Universal Integrated Circuit Card.  
About Device Settings  
View information about your device, including status, legal information, hardware and software  
versions, and a tutorial.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
About device, and then tap items for more details:  
Software version: View your phone’s software version.  
Hardware version: View the hardware version of your device.  
Status: View information about your device’s current status.  
l
l
l
l
Legal information: Display open source licenses, Google legal information, a privacy alert,  
and licenses.  
l
Report diagnostic info: When enabled, your phone reports diagnostic and usage data to  
Samsung, to improve the quality and performance of products.  
Settings  
190  
   
l
l
l
l
l
l
l
l
Device name: View your device’s name, and enter a new name if desired.  
Model number: View your device’s model number.  
Android version: View the firmware version of your device.  
Baseband version: View the baseband version of your device.  
Kernel version: View the kernel version of your device.  
Build number: View the build number of your device.  
SE for Android status: View your device’s current status.  
Security software version: View your device’s security software version.  
Application Manager Settings  
You can download and install applications from the Google Play Store or Samsung Apps, or create  
applications using the Android SDK and install them on your device. Use Application manager to  
manage applications on your device.  
Warning: Because this device can be configured with system software not provided by or supported  
by Google or any other company, end-users operate these devices at their own risk.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Application manager to view app status. While in Application manager, you can use  
these options:  
l
l
Tap Downloaded, SD Card, Running, or All to view the status of apps and services. Tap  
an app or service for more information, and for app options, such as stopping and  
uninstalling.  
Tap  
More for other options, including sorting by app size or name, or resetting app  
preferences.  
Default Applications Settings  
If you have installed multiple apps that perform the same kind of task, for example more than one  
messaging app, you can choose the app you want to use as the default.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Default applications to configure options:  
Settings  
191  
   
l
l
l
Home: Choose a default home screen mode.  
Messages: Choose a default app for messaging (SMS and MMS).  
Clear defaults: Tap Clear to clear the defaults.  
Note: If you choose a default messaging app other than Messages (for example, Google Hangouts),  
you will not be able to use the Messages app unless you restore it as the default messaging app. For  
Calendar Settings  
Configure settings for your phone’s Calendar app.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Calendar to configure these options:  
l
l
l
First day of week: Choose a day to start each calendar week.  
Show week numbers: Enable or disable display of week numbers on the calendar.  
Hide declined events: When enabled, events for which you declined the invitation are not  
shown on the calendar.  
l
l
l
l
l
Hide completed tasks: When enabled, tasks you’ve completed are no longer shown on the  
calendar.  
Weather: When enabled, weather information from AccuWeather.com displays on the  
calendar.  
Lock time zone: When enabled, event times will be locked to the time zone you select. This  
means that times and dates will not change, even if you travel to another time zone.  
Select time zone: When you enable Lock time zone, choose a time zone to lock events to  
the time zone.  
Select alert type: Choose the type of notifications for calendar events. You can choose to  
be notified with a sound, or by an icon in the status bar, or choose no notifications.  
l
l
l
Notification sound: Choose a sound for calendar event notifications.  
Vibration: Enable or disable vibration, to play for calendar event notifications.  
Quick responses: Manage text phrases, which you can use to send to event attendees.  
Settings  
192  
 
Call Settings  
Configure options for calling with your phone.  
Tip: You can also access Call settings from the Phone app. From home, tap  
Phone >  
Menu > Settings > Call.  
Call Rejection  
Create and manage a list of phone numbers, to have your device automatically reject calls you  
receive from those numbers.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Call rejection to configure these options:  
l
Auto reject mode: When All numbers is selected, calls from all numbers are rejected.  
When Auto reject numbers is selected, calls from numbers on the Auto reject list are  
rejected.  
l
Auto reject list: Enter telephone numbers, to reject calls from the numbers when Auto  
reject mode is turned on.  
o
Tap  
Add to enter a telephone number, or select a number from a contact. Tap  
Match criteria to set options for using the reject number list.  
o
Tap the check box beside Unavailable to reject calls with numbers that display  
“Unavailable” in Caller ID.  
l
Set up call rejection messages: Create and manage text messages to send to callers  
when rejecting incoming calls. Messages you create here are available from the incoming  
call screen when you use the Reject with message option  
o
To create new messages, tap Create, and then follow the prompts.  
o
To modify an existing message, tap the message, and then edit the text.  
Answering and Ending Calls  
Manage settings for answering and ending calls.  
Settings  
193  
     
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Answering and ending calls to configure these options:  
l
Answer calls by:  
o
o
Pressing the Home key: When enabled, you can answer incoming calls by pressing  
the Home key.  
Voice control: When enabled, you can answer or reject calls with the voice commands  
“Answer” and “Reject”. When you answer a call with a voice command, the Speaker will  
automatically turn on for hands-free calls. Voice control will not be available if you set call  
alerts to vibration.  
o
Waving hand over device: When enabled, you can answer a call by passing your hand  
over the device.  
l
End calls by:  
o
Pressing the power key: When enabled, you can end calls by pressing the  
Power/Lock key. In this case, pressing the power key during a call will not lock the  
screen.  
Call Notification Pop-ups  
When enabled, notifications for incoming calls display in pop-ups if an application is open on the  
screen.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Call notification pop-ups to enable or disable the option.  
In-call Status Pop-ups  
When enabled, a pop-up displays on the screen to show call status if an application is open on the  
screen.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > In-call status pop-ups to enable or disable the option.  
Settings  
194  
   
Show Caller Information  
When enabled, information about the caller’s recent social network activity, and the history of your  
communication with them, displays when you receive a call.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Show caller information to enable or disable the option.  
Call Alerts  
Set options for sounds and vibrations to occur during calls.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Call alerts to configure settings:  
l
Vibrate on connection to network: When enabled, your phone will vibrate when a call  
connects to the network.  
l
l
Call-end vibration: When enabled, the phone vibrates when the other caller ends the call.  
Call connect tone: When enabled, the phone plays a tone when the other caller answers a  
call.  
l
l
l
Minute minder: When enabled, a tone plays once per minute during a call.  
Call end tone: When enabled, the device plays a tone when the other caller ends the call.  
Notify during calls: When enabled, notifications for alarms and new messages play during  
calls. When disabled, these notifications will be muted during a call.  
Call Accessories  
Configure options for using an optional headset for calling.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Call accessories to configure settings:  
l
Automatic answering: When enabled, and you have a headset connected to the Headset  
Jack, incoming calls are answered automatically after a delay, which you can set at  
Automatic answering timer. Tap to enable or disable the setting.  
Settings  
195  
     
l
l
Automatic answering timer: Choose a time period to delay before automatically  
answering an incoming call when Automatic answering is enabled and a headset is  
connected to the device. Tap to choose 2 seconds, 5 seconds, or 10 seconds.  
Outgoing call conditions: When the device is paired with a Bluetooth headset, you can  
choose to make calls even when the device is locked. Tap to choose Even when device  
locked, or Only when device unlocked.  
TTY Mode  
A TTY (teletypewriter, also known as a TDD or Text Telephone) is a telecommunications phone that  
allows people who are deaf, hard of hearing, or who have speech or language disabilities, to  
communicate by telephone.  
Your phone is compatible with select TTY phones. Please check with the manufacturer of your TTY  
phone to ensure that it supports digital wireless transmission. Your phone and TTY phone will  
connect using a special cable that plugs into your phone’s headset jack. If this cable was not  
provided with your TTY phone, contact your TTY phone manufacturer to purchase the connector  
cable.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Additional settings > TTY mode to choose a mode, from TTY Off, TTY Full,  
TTY HCO, or TTY VCO.  
Hearing Aids  
When enabled, your phone improves the sound quality for use with hearing aids.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Additional settings > Hearing aids to enable or disable the option.  
Ringtones and Keypad Tones  
Choose tones and vibrations to play for incoming calls and keypad taps.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call > Ringtones and keypad tones to configure settings:  
l
Tap Ringtones, and then select a ringtone for incoming calls. Tap OK to save your  
selection.  
Settings  
196  
     
l
Tap Vibrations, and then select a vibration pattern to play for incoming calls when the  
Vibrate when ringing option is enabled. You can tap Create to create a custom pattern. Tap  
OK to save the settings.  
l
l
Tap Vibrate when ringing to play a vibration for incoming calls. The vibration pattern is set  
at the Vibrations setting.  
Tap the check box beside Dialing keypad tone to enable or disable tones for keypad taps.  
Personalize Call Sound  
Choose options for call audio, in cases where you might need the sound softer or more clear, or  
optimized for your right or left ear.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Personalize call sound.  
3. Tap a setting, and then configure options if available:  
l
Adapt sound: Tap Start, and then follow the onscreen prompts to find the best sound for  
you.  
l
l
l
Soft sound: Use softer sounds during calls.  
Clear sound: Use clearer sounds during calls.  
Off: Use the default call sound settings.  
Noise Reduction  
When enabled, Noise reduction suppresses background noise from your environment during calls.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Noise reduction to enable or disable noise reduction.  
US Dialing  
When enabled, the US dialing option replaces “+” with the international access code for your  
location.  
Settings  
197  
     
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call, and then tap the check box beside US dialing to enable or disable the setting.  
International Dialing  
When US dialing is enabled, it uses the International dialing code to replace “+”. US dialing must be  
disabled to access the International dialing code.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call, and then tap the check box beside US dialing to disable the setting. US dialing  
must be disabled to access the International dialing setting.  
3. Tap International dialing, and then use the keypad to enter the international dialing code.  
4. Tap OK to save the code.  
DTMF Tones  
Set the length of Dual-tone Multi-frequency (DTMF) tones, which play when you use the keypad  
during a call, such as when navigating menus.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > DTMF tones to choose a tone length, from Normal, or Long.  
Voicemail Settings  
Set options for Visual Voicemail.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap Call > Voicemail settings to configure options for voicemail.  
Voice Privacy  
When enabled, Voice privacy improves the security of voice calls.  
Settings  
198  
       
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Call, and then tap the check box beside Voice privacy to enable or disable enhanced  
privacy mode.  
Contacts Settings  
Configure options for contacts stored on your phone.  
Tip: You can also access Contacts Settings from the Contacts app. From home, tap  
Contacts  
>
Menu > Settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Contacts to configure options:  
l
Import/Export: You can import contacts from your phone’s internal memory, from the SIM  
card, or from an optional installed memory card. Tap to choose an import source, and then  
follow the prompts to import contacts.  
l
l
l
Contacts to display: Choose contacts to display in Contacts. You can choose only  
contacts from your phone’s memory, or from an account, or choose other sources. You can  
also create a customized list of contacts to display.  
Swipe to call or send message: When enabled, you can swipe your finger across a  
contact record to call or send a message to the contact’s default number. Swipe right to call,  
or left to create a message addressed to the contact.  
Only contacts with phones: When enabled, only contacts with at least one phone number  
display in Contacts. Other contacts will be hidden.  
l
l
l
Sort by: Choose how contacts are sorted, by first or last name.  
Display contacts by: Choose how contacts are displayed, by first or last name.  
Send contact information: You can choose how to transfer contacts, when sharing them  
with other devices, such as via Bluetooth.  
o
Send all namecards: Multiple contacts are sent together. This method can be faster,  
but depends on whether the target device can accept multiple namecards. If not, only  
one contact will be sent.  
o
Send individual namecards: Namecards are sent individually. This method may take  
longer, because the other device must accept each namecard individually, but it helps  
ensure that no namecards are missed.  
Settings  
199  
 
l
Accounts: Add or manage accounts. Many accounts include contacts, which are synced  
with your phone when you set up the account on your phone.  
Email Settings  
Configure options for email accounts you set up on your phone.  
Tip: You can also access Email settings from the Email app. From home, tap  
Apps >  
Email >  
Menu > Settings.  
Edit General Email Preferences  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Email to configure options. Available settings depend on the type of email account, and  
may include:  
l
l
Manage accounts: Configure options for specific accounts. Available settings depend on  
the type of account.  
Display: Choose how emails are shown in the email list, and when you open them.  
o
Auto fit content: When enabled, email content shrinks to fit the screen. You can still  
view details by zooming in.  
o
Message preview line: Choose whether up to 3 lines display with the email subject in  
the Inbox.  
o
Title line in list: Choose what displays as the title in the list of emails, the sender, or the  
subject of the email.  
o
Hide checkboxes: Enable or disable the display of checkboxes beside each email.  
When checkboxes are displayed, you can use them to select email(s). If you choose to  
hide checkboxes, you can touch and hold on an email to temporarily display them, such  
as when you want to select multiple emails.  
l
l
Default display: Select what’s displayed after you move or delete emails. You can choose  
to move to the next email, or the previous email, or return to the list of emails in the inbox.  
Priority sender settings: Choose options for handling emails from priority senders.  
o
Set as default folder: When enabled, the priority sender inbox displays when you open  
the Email app.  
o
Email notifications: When enabled, notifications for new emails display in the status  
bar. When disabled, you can control notifications for each of your email accounts  
individually in the account’s settings.  
Settings  
200  
 
o
o
Notification sound: Choose a ringtone to use for notifications for new email from  
priority senders.  
Vibrate: Enable or disable vibration, to play for notifications for new email from priority  
senders.  
l
l
Spam addresses: Create and maintain a list of email addresses and domains, to  
automatically block emails from those senders.  
Delay email sending: Choose options for delaying the sending of emails, so that they can  
be cancelled if needed.  
o
Delay email sending: When enabled, the sending of emails is delayed, and a cancel  
button is displayed, for a period of time you set below.  
o
Set length of delay: Choose a time period to delay sending of emails.  
Manage Email Account Settings  
You can edit settings for your individual email accounts, such as email address and password, name  
display and signature, frequency of retrieval, and more.  
Note: Available settings depend on the type of email account.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Email > Manage accounts, and then choose an account to configure settings:  
l
Sync settings: Tap to configure options for synchronizing your phone with your account:  
o
Sync Email: When enabled, your phone maintains synchronization with your email  
account. The last synchronization is displayed.  
o
Sync schedule: When Sync email is enabled, set options for synchronizing your phone  
with your email account.  
o
Period to sync Email: Choose a time period to have your phone maintain  
synchronization.  
o
Limit retrieval size: Choose a maximum size for emails for your phone to automatically  
retrieve during synchronization. For larger emails, your phone will prompt you to  
download the contents when you open them. You can set a separate retrieval limit to use  
when roaming.  
l
l
Signature: When on, a text signature is automatically added to emails you send. Tap the  
ON/OFF switch to turn signatures on or off. After turning signatures on, tap Edit signature  
to edit the default text signature.  
Out of office settings: Configure options for automatically sending replies when you are  
out of the office.  
Settings  
201  
l
Default account: Assign an account as the default email account for outgoing messages.  
When you launch an email from other apps, the email will automatically be from this account.  
l
l
Password: Update your account password to match the password set on your account.  
Email notifications: When enabled, an icon displays in the Status bar when you receive  
new emails.  
l
l
l
Notification sound: Choose a ringtone to play for new email notifications.  
Vibrate: When enabled, vibration plays for new email notifications.  
More settings: Configure other options, including the account name, carbon copy and blind  
carbon copy, synchronization, and security options.  
o
Account name: Enter a name to identify this email account.  
o
Your name: Enter a name, to be shown to recipients in emails from this account.  
o
Always Cc/Bcc myself: Choose options for sending a copy of emails you send to  
yourself, as a copy (Cc) or blind copy (Bcc).  
o
Show images: Choose whether to automatically display embedded images in the body  
of an email.  
o
Auto download attachments: Choose whether the phone automatically downloads  
email attachments when you are connected to Wi-Fi. You might use this option to control  
how and whether you use your plan’s data services to download attachments.  
o
Auto resend times: Choose the number of times the phone attempts to resend an  
email after a delivery failure.  
o
Folder sync settings: Choose folders to synchronize between your phone and  
account.  
o
Period to sync Calendar: Choose the period for synchronizing calendar events  
between your phone and account.  
o
Empty server trash: Delete the contents of the trash folder on the account server.  
o
In case of sync conflict: Choose whether information from the server or phone has  
priority when there is a conflict.  
o
Security options: Configure advanced security options, including encryption.  
o
Number of emails to load: Choose the number of emails displayed at one time.  
o
Sync Contacts: Choose whether contacts are synchronized between your phone and  
the account.  
o
Sync Calendar: Choose whether calendar events are synchronized between your  
phone and the account.  
Settings  
202  
o
o
o
o
Sync Task: Choose whether emails are synchronized between your phone and the  
account.  
Exchange server settings: Configure the Domain\user name, Password, and other  
Exchange server settings.  
Incoming settings: Configure settings for the account server to access your account on  
your phone.  
Outgoing settings: Configure settings for accessing your account from your phone.  
Gallery Settings  
Configure options for the Gallery app.  
Tip: You can also access Gallery settings from the Gallery app. From home, tap  
Apps >  
Gallery >  
Menu > Settings.  
From home, tap Apps >  
Gallery to configure options:  
1.  
2.  
Settings.  
Tap  
l
Accounts: Tap an account to enable or disable sync options. The sync options for pictures  
and videos affect Gallery.  
l
SNS Data Management: Configure options for synchronizing pictures and videos with your  
SNS (Social Networking Site) accounts.  
o
Sync via Wi-Fi only: When enabled, Gallery will only sync pictures with your SNS  
(Social Networking Site) accounts when connected to Wi-Fi.  
l
Cloud Sync: Select options to sync gallery items, for example, to use Dropbox sync to store  
your gallery items.  
l
l
Filter by: Choose a filter to apply to pictures displayed in Gallery.  
Tag buddy: When on, Tag buddy automatically adds tag information to pictures you take.  
Tap the ON/OFF switch to turn the option on, and then tap items to enable tags in pictures.  
l
l
Face tag: When enabled, your phone identifies faces in the pictures you take, so you can tag  
them in the picture.  
Tap  
Menu > Add account to add an account for picture and video storage.  
Settings  
203  
 
Internet Settings  
Configure Internet settings, to customize the browser to your preferences.  
Basic Internet Settings  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Internet to configure options:  
l
Account: Tap to sign in to your Samsung account. Signing in to your Samsung account  
allows you to sync bookmarks and open pages with your other devices.  
l
l
Set homepage: Tap to choose a homepage, to display when you launch Internet.  
Auto fill forms: Manage text phrases for automatically filling out Web forms.  
Advanced Internet Settings  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Internet to configure options:  
l
Privacy: Choose options related to privacy.  
o
Suggest search terms and Web addresses: When enabled, the browser will predict  
related queries and popular sites based on what you enter in the Navigation bar.  
o
Preload available links: When enabled, the browser will preload links from the cache,  
to improve performance when loading pages.  
o
Remember form data: When enabled, the browser will remember data you enter in  
Web form, to help you fill out these fields in the future.  
o
Remember passwords: When enabled, the browser saves user names and  
passwords you enter, to help you fill out those fields in the future.  
o
Delete personal data: Choose types of personal data to delete from browser settings.  
l
Screen and text: Configure options for the browser’s screens.  
o
Text scaling: Drag the slider to adjust the size of type on the screen. Use the Preview to  
see an example.  
o
Force zoom: When enabled, the browser overrides requests from websites to control  
zoom level.  
Settings  
204  
 
o
o
o
Text encoding: Choose a type of text encoding, or choose Auto detect to have the  
browser detect the type.  
Full screen: When enabled, pages display full-screen, hiding the status bar. You can  
touch the screen to display the status bar.  
Text booster: When enabled, the browser increases the size of text for easier reading,  
especially when viewing desktop versions of websites on your phone. This may affect the  
screen’s layout.  
l
Content settings: Choose settings to control how the browser treats content.  
o
Accept cookies: When enabled, the browser allows sites to save and read cookies.  
o
Turn on location: When enabled, sites can access your phone’s location information.  
o
Turn on JavaScript: When enabled, the browser allows sites to run JavaScript.  
o
Block pop-ups: When enabled, the browser does not display pop-up screens from  
websites  
o
Default storage: If you have an optional installed memory card installed (not included),  
you can choose where to store browser data.  
o
Website settings: Set advanced settings for individual websites. If you’ve visited sites  
that offer advanced settings, you can configure those settings here. Available websites  
and settings depend on your browsing history.  
o
Turn on notifications: Control whether the browser notifies you of Web notifications.  
o
Clear notifications: Remove Web notification access information.  
o
Reset settings: Restore the browser’s default settings.  
l
Bandwidth management: Configure options to allow the browser to manage data use.  
o
Preload webpages: Choose whether the browser preloads Web pages for faster  
browsing all the time, only when connected to Wi-Fi, or never.  
o
Load images: When enabled, the browser will automatically load and display images on  
Web pages.  
o
Open pages in overview: When enabled, newly opened pages display as an overview.  
Messages Settings  
The messages settings menu lets you control options for your text and MMS messages including  
message limits, size settings, and notifications.  
Settings  
205  
 
Tip: You can also access Message settings from the Messages app. From home, tap  
Messages > Menu > Settings.  
1.  
2.  
From home, tap  
Apps >  
Settings.  
Tap  
Messages to configure settings:  
Default messaging app: Choose an app to use by default.  
Display:  
l
l
o
Bubble style: Choose how messages appear on the screen. Bubbles are the boxes that  
surround each message.  
o
Background style: Choose the background of the message screen.  
o
Change font size: When enabled, you can change the text size while reading a  
message by pressing the Volume key up or down.  
Quick responses: Create and manage text phrases that you can add to messages.  
Text messages:  
l
l
o
Auto combination: Choose whether long messages that are received in multiple parts  
are automatically re-assembled to display as a single message.  
l
Multimedia messages:  
o
Group conversation: Control how messages to multiple recipients are handled. When  
enabled, a single message is sent to multiple recipients. When disabled, a separate  
message is sent to each recipient.  
o
Auto retrieve: Choose whether message attachment(s) are automatically downloaded  
when you display a multimedia message. If you disable this option, only the message  
header displays in the message list, and you’ll be prompted to download the attachment  
(s).  
o
Roaming auto retrieve: Choose whether message attachment(s) are automatically  
downloaded when your phone is outside its home network.  
o
MMS alert: When enabled, your phone will alert you when you make a change to a  
message that will convert the message to a multimedia message (MMS).  
l
Delete old messages: When turned on, your phone will automatically delete the oldest  
messages when the maximum number of messages is reached. Tap the ON/OFF switch to  
turn the setting on, and then set the maximum number of messages with the Text message  
limit and Multimedia message limit settings below.  
o
Text message limit: Set the maximum number of text messages per conversation.  
Settings  
206  
o
Multimedia message limit: Set the maximum number of multimedia messages per  
conversation.  
l
Notifications: When turned on, notifications for new messages display in the status bar.  
Tap the ON/OFF switch to turn the setting on, and then configure options:  
o
Notification sound: Choose a sound to play for new message notifications.  
o
Vibrate: Choose whether vibration plays along with the sound for new message  
notifications.  
o
Repeat message alert: Choose how often your phone notifies you of new message(s).  
o
Pop-up display: Choose whether a new message pops up on the display to notify you.  
o
Preview message: Choose whether a short preview of new messages displays in the  
Lock screen and/or Status bar.  
l
Emergency alerts: Configure emergency alert settings. You can enable or disable some  
alerts: Extreme Alert, Severe Alert, Amber Alert, and Emergency alert test messages. You  
cannot disable Presidential alerts.  
o
Emergency alerts: Choose types of messages to receive. You can enable or display  
any of the message types, except for Presidential Alert. You can also choose to receive  
emergency alert test messages.  
Important: The Commercial Mobile Alert System (CMAS) system provides the government the  
ability to send geographically targeted notifications of emergencies, such as threats to public safety,  
severe weather events, a hazardous material spill or a missing child in the phone user’s area.  
o
Emergency notification preview: Play a sample emergency alert tone. Tap Stop to  
cancel the playback.  
o
Vibrate: Select vibration options for emergency message notifications.  
o
Alert reminder Configure the reminder interval.  
l
l
Signature: When turned on, a text signature is included in all messages you send. Tap the  
ON/OFF switch to turn the setting on, and then edit the signature text to include.  
o
Edit signature: Enter a text signature, when Add signature is enabled.  
Spam filter: When turned on, your phone block messages that may be spam, by filtering  
based on criteria you set. Tap the ON/OFF switch to turn the setting on, and then configure  
filters:  
o
Add to spam numbers: Enter telephone numbers, to automatically flag messages  
from the numbers as spam, when Spam settings is enabled.  
o
Add to spam phrases: Enter text phrases, to automatically flag messages as spam  
when they contain the phrase. Available when Spam settings are enabled.  
Settings  
207  
o
Block unknown senders: When enabled, your phone blocks messages from numbers  
that are not stored as contacts.  
l
l
Delay message sending: When turned on, you can choose to delay the sending of  
messages, so that they can be canceled if needed. Tap the ON/OFF switch to turn the  
setting on, and then set the length of delay.  
Safe mode: Choose options for working with messages when your phone is in safe mode.  
S Voice Settings  
Configure options for using your voice to interact with your phone.  
Tip: you can also access S Voice settings from the S Voice app. From home, tap  
Apps >  
S
Voice >  
Menu > Settings.  
1.  
2.  
From home, tap Apps >  
Settings.  
Tap  
S Voice >  
Menu > Settings to configure options:  
l
Language: Choose a language to use for S Voice.  
l
Hide offensive words: When enabled, potentially offensive words are replaced with  
asterisks (*).  
l
l
About: Learn about S Voice.  
Open via the home key: When enabled, you can launch S Voice by pressing the Home key  
twice quickly.  
l
Voice wake-up: When turned on, you can launch S Voice by speaking a wake-up  
command. Tap the ON/OFF switch beside Voice wake-up to turn the option on, and then  
tap Set wake-up command to record a command.  
l
l
l
l
l
Auto start speakerphone: When enabled, the speaker is automatically turned on when  
you make a call with S Voice.  
Show body of message: When enabled, the body of new message is displayed on the  
screen when it arrives.  
Check missed events: When enabled, you can check missed events when you open S  
Voice via an optional headset.  
Personal briefing: When enabled, S Voice will provide a briefing on your schedule when  
you open S Voice.  
Home address: Configure your home address.  
Settings  
208  
 
l
l
Log in to Facebook: Log in to your Facebook account. If you have not already installed an  
optional Facebook app, follow the prompts to do so before logging in.  
Log in to Twitter: Log in to your Twitter account. If you have not already installed an  
optional Twitter app, follow the prompts to do so before logging in.  
Settings  
209  
Copyright Information  
©2014 Sprint. Sprint and the logo are trademarks of Sprint. Other marks are trademarks of their  
respective owners.  
©2014 Samsung. Samsung, Galaxy, S Beam, Air View, S Health, and S Voice are trademarks of  
Samsung Electronics Co., Ltd.  
©2014 Google. Android, Chrome, Gmail, Google Maps, Play Music, Play Movies & TV, Play Books,  
Play Newsstand, Play Games, Drive, YouTube, Photos, Hangouts, Google Mobile Services, and  
Google Play are trademarks of Google, Inc.  
Other marks are property of their respective owners.  
Screen images simulated.  
Appearance of device may vary.  
Copyright Information  
210  
 
Index  
Answering and Ending Calls 193  
Application Manager Settings 191  
Applications 69  
3
4
3-way Calling 33  
Auto Adjust Screen Tone 158  
B
Backup and Reset Settings 176  
Battery  
A
Install 1  
About Device Settings 190  
Access Contacts 43  
Access Email and Data Services  
Internationally  
CDMA Networks 130  
GSM/UMTS Networks 130  
Access Settings 134  
Accessibility 167  
Battery Settings 185  
Before Updating Your Firmware 124  
Blocking Mode Settings 172  
Bluetooth 98, 101  
Connect to a Car Kit 101  
Receive Information 104  
Reconnect a Headset or Car Kit 102  
Send Information 103  
Turn On or Off 101  
Settings 167  
Accessibility Services 172  
Accessibility Settings  
Dexterity and Interaction 170  
Hearing 169  
Unpair 102  
Bluetooth Settings 139  
Brightness 156, 158  
Browser 83  
Other 171  
Vision 167  
Accessories Settings 185  
Account  
Manage 7  
Services 8  
Account Passwords 6  
Accounts 54  
C
Calculator 108  
Calendar 105  
Add an Event 105  
Calendar Settings 192  
Call a Number in a Text Message 30  
Call Accessories 195  
Call Alerts 195  
Call Forwarding 34  
Call Notification Pop-ups 194  
Call Rejection 193  
Call Settings 42, 193  
Call Waiting 33  
Email 56  
Gmail 54  
Google 54  
Social Network 66  
Accounts Settings 175  
Activate This Device 189  
Activation 3  
Add an Email Account 56  
Add or Edit Information for a Contact 45  
Advanced Wi-Fi Settings 135  
Air View 12  
Caller ID 32  
Camera 10, 89  
Camera and Video 89  
Chrome 83  
Air View Settings 175  
Airplane Mode 140  
Alarm & Timer 109  
Allowed Devices 138  
Android Beam 145  
Clock 109  
Cloud Settings 176  
Configure Hotspot 137  
Configure Smart Remote 117  
Configure the Camera 92  
Index  
211  
 
Configure Wi-Fi Settings 135  
Connect to a Wireless Network 81  
Contact Sprint for Assistance with  
International Service 132  
Contacts 43  
E
Earpiece 9  
Easy Mode Settings 167  
eBay 80  
Edit Email Settings 60  
Editing Text 27  
Add 44  
Assign a Picture 46  
Assign a Ringtone 46  
Edit 45  
Get Started 43  
Email 56  
Compose 58  
Corporate Accounts 57  
Email Message  
Groups 49  
Make call from 30  
Email Settings 200  
Emergency Numbers 30  
Emergency Tone 153  
Encryption 187  
Enhanced 9-1-1 (E 9-1-1) 31  
Enter Text 24  
Entertainment 69  
Erase Events 108  
Eureka Offers 80  
Make call from 29  
Save a Number 45  
Share 51  
Contacts Settings 44, 199  
Create a Google Account 54  
Credential Storage 189  
Customize Your Home Screen 18  
Customize Your Smart Remote 117  
D
Event Alerts 106  
Export and Import Contacts 52  
Extended Home Screen 20  
Data 83  
Data Connection  
Status and Indicators 84  
Data Services 83  
F
Password 7  
Data Usage 141  
Date and Time Settings 183  
Daydream 158  
Default Applications Settings 191  
Default Input Method 177  
Default Language 177  
Default Messaging App Settings 143  
Delete an Email Account 61  
Delete Contacts 47  
Device Administration 187  
Dialing Keypad Tone 152  
Dialing Options 32  
Facebook 66  
Favorites 49  
Features 9, 11  
Files  
Transfer between phone and  
computer 123  
Find a Contact 43  
Finger Scanner 173  
Fingerprint Screen Lock 162  
Flash 10  
Flick 16  
Flipboard 111  
Font 157  
Display Settings 156  
Drag 15  
Drive 110  
Forward Email 59  
Front camera 10  
Dropbox 110  
G
Accessing Dropbox on Your  
Device 111  
Gallery 94  
Download the Desktop Application 110  
Manually Uploading a Picture 111  
DTMF Tones 198  
Gallery Settings 203  
Gestures 14  
Global Roaming Mode 127  
Gmail 54  
Index  
212  
Google  
Sign in 54  
Voice Typing 24  
Google Checkout 70  
Google Maps 71  
L
Language and Input 177  
LED Indicator Settings 159  
Link Contacts 46  
Location Settings 142  
Lock Screen Settings 160  
Logs 40  
Lookout Security 112  
Lumen Toolbar 112  
Google Now 111  
Google Play Books 77  
Google Play Games 77  
Google Play Movies 76  
Google Play Music 72  
Google Play Newsstand 77  
Google Play Store 69  
Install an App 69  
Google Search 112  
Google Voice Typing 25, 181  
Configuring 25  
M
Make and Receive Worldwide Calls 127  
Manage Your Email Inbox 59  
Managing Conversations 63  
Maps  
Google 71  
Memo 113  
Using 25  
Google+ 67, 99  
Merge Contacts 48  
Messages Settings 205  
Messaging 61  
Options 65  
Messaging Plus 65  
Microphones 10  
MMS Messaging 61  
Mobile Networks Settings 143  
More Networks Settings 143  
Motion  
H
Hangouts 67  
Haptic Feedback 153  
Headset Jack 10  
Hearing Aids 196  
Help 112, 189  
Home Screen 18  
Extended 20  
Shortcuts 18  
Hotspot 85  
Settings 174  
Motions and Gestures 12  
Mouse/Trackpad Settings 183  
Multi Window 13  
Hotspot Settings 137  
I
Multi Window Settings 165  
Music 72  
In-call Options 34  
In-call Status Pop-ups 194  
Infrared transmitter 10  
Install a microSD Card 121  
International Data Roaming 129  
International Dialing 198  
International Roaming Status  
Messages 130  
Google Play Music 72  
Player 72  
Sprint Music Plus 72  
Music Effects 156  
My Files 113  
My Magazine 114  
International Voicemail 128  
International Voicemail Troubleshooting 129  
Internet Settings 204  
N
NASCAR Mobile 2014 79  
Navigation 71  
K
Scout 71  
NBA Game Time 79  
Nearby Devices Settings 147  
New Messages Notification 63  
NextRadio 79  
Keyboard 178-179  
Samsung 178-179  
Keypad Tones 196  
Index  
213  
NFC Settings 145  
Make call from 29  
Reply to Email 59  
Retrieve Your Voicemail Messages 36  
Review Pictures and Videos 91  
Review Visual Voicemail 38  
Ringtones 151, 196  
Noise Reduction 197  
Notification Icons 22  
Notification Panel 23  
Notification Panel Settings 165  
Notifications 21, 151  
Roaming Settings 144  
Rotate 16  
O
One-handed Operation Settings 167  
Open an Installed App 70  
Open the Camera 89  
S
S Beam Settings 146  
S Health 114  
P
S Voice 116  
S Voice Settings 208  
Safety Assistance 184  
Samsung Account 56  
Samsung Applications Sound Settings 153  
Samsung Apps 72  
Samsung Keyboard 26, 178-179  
Samsung Keyboard Sound Settings 153  
Save a Business Card 47  
Save and Resume a Draft Message 63  
Scout 71  
Password Screen Lock 164  
Passwords 187  
Pattern Screen Lock 161  
Personalize Call Sound 197  
Phone 29  
Layout 9  
Navigation 14  
Phone Call Options 32  
Phone calls  
Using contacts 29  
Phone Calls  
Screen Lock 160  
Screen Lock Sound 152  
Screen Mirroring Settings 149  
Screen Mode 158  
Screen Rotation 157  
Screen Timeout 157  
SD Card 121  
Emergency numbers 30  
From email messages 30  
From text messages 30  
Make calls 29  
Receive 31  
Using phone keypad 29  
Using recent calls 29  
Phone Overview 1  
Photos 100  
Format 122  
Remove 122  
Unmount 123  
View Memory 122  
Picasa 99  
Search Settings 134  
Security Settings 187  
Security Update Service 188  
Send a Gmail Message 55  
Send a Multimedia Message 62  
Send a Text Message 61  
Send Information to Another Device 103  
Set Up Phone 1  
PIN Screen Lock 163  
Pinch 17  
Play Store 69  
Plus (+) Code Dialing 127  
Polaris Office 5 114  
Power Saving Settings 185  
Printing Settings 148  
Private Mode Settings 173  
Proximity sensor 9  
Set Up Visual Voicemail 37  
Settings 134  
Accessibility 167  
Data Usage 141  
Display 156  
Language and Input 177  
Motion 174  
R
Read and Reply to Gmail Messages 55  
Recent Calls  
Clear 41  
Index  
214  
Wi-Fi 135  
Text Messaging 61  
Make call from 30  
Toolbox 166  
Tools and Calendar 101  
Touch 14  
Touch and Hold 14  
Touch Key Light Duration 159  
Touch Sensitivity 160  
Touch Sounds 152  
Touchscreen  
Settings Options 134  
Setup Application 4  
Share Photos and Videos 98  
Show Caller Information 195  
SIM Card 126  
Slide 15  
Smart Remote 117  
Control Your TV 118  
Smart Stay 157  
SMS  
Turn off 11  
Messaging 61  
Turn on 11  
Social Network Accounts 66  
Sound Mode 149  
Sound Settings 149  
Speaker 10  
Speech Settings 182  
Speed Dialing 48  
Spread 17  
TTY Mode 196  
Turn Hotspot On or Off 137  
Turn NFC On or Off 145  
Turn Phone On or Off 11  
Turn Screen On or Off 11  
Typing 24  
U
Sprint 411 8  
Sprint Account  
Uninstall an App 70  
Update  
Firmware 124  
Update Your Phone 124  
US Dialing 197  
USB Charger/Accessory port 10  
USB Support 3, 10  
Using Settings 134  
Information and Help 6  
Sprint Money Express 78  
Sprint Music Plus 75  
Sprint Operator Services 8  
Sprint TV & Movies 78  
Sprint Worldwide Data Services  
Get Started 130  
Sprint Worldwide Wireless Service 126  
Sprint Zone 78  
Status 21  
V
Vibrate When Ringing 152  
Vibration Intensity 150  
Vibrations 151  
Video 100  
Videos  
Status Bar 21  
Status Icons 21  
Storage Settings 186  
Swipe 15  
Swipe Screen Lock 161  
Swype 26  
Record 90  
View Events 107  
View Photos and Videos 95  
Visual Voicemail 37  
Configure Settings 39  
Listen to multiple messages 38  
Options 38  
Voice Privacy 198  
Voice Recorder 118  
Voice Search 120  
Voice Typing 24  
Configuring 25  
System Update Settings 190  
T
Take a Picture 90  
Tap and Pay 146  
Tethering Settings 140  
Text-to-Speech 182  
Text Editing 27  
Text Entry 24  
Text Input  
Methods 24  
Using 25  
Index  
215  
Voicemail 35  
Display name 39  
Greeting 39  
International 128  
Notification 36  
Password 7  
Setup 6  
Voicemail Access Number 128  
Voicemail Settings 198  
Voicemail Setup 36  
Volume 150  
VPN 86, 144  
Add a VPN 86  
Connect to a VPN 88  
Disconnect from a VPN 88  
Prepare Your Phone for VPN  
Connection 86  
W
Wallpaper Settings 160  
Web 81  
Wi-Fi 81  
Settings 135  
Turn On or Off 81  
Wi-Fi Direct Settings 136  
Working with Photos 97  
Y
Your User Name 84  
YouTube 66, 99  
Z
Zoom 17  
Index  
216  

Sunbeam 3280 User Manual
Sony CDX F7710 User Manual
Sonic Alert SBA475SS User Manual
Seagate SAVVIO ST600MM0026 User Manual
Seagate SAVVIO 15K2 SAS ST9146652SS User Manual
Seagate Momentus ST91008220AS User Manual
Samsung 20040414141622906 User Manual
Panasonic EB VS2 User Manual
Panasonic CQ DFX55 User Manual
Numark Industries M6 User Manual