FireWire 800 CardBus DV-Kit
Quick Installation Guide
Introducing the FireWire 800 DV-Kit
The FireWire 800 Cardbus DV-Kit is designed to add
FireWire 800 (1394b) and 1394a (6-pin) interfaces to your
notebook computer. For your convenience, one FireWire
(1394a) 6-pin/4-pin DV cable is included for connecting
DV camcorders and other 1394 devices using 4-pin
connector. Ulead VideoStudio video editing software is
also included for producing greeting cards, video
e-mails, or home videos complete with attractive titles,
effects, and background music.
FeaturesandBenefits
•
•
•
•
Provides 2 FireWire 800 (9-pin) and 1 FireWire 400
(6-pin) ports for multiple device connections
Supports serial bus data transfer rates of 100, 200,
400 and 800 Mbps
Hot-swappingallowsyoutoconnect/detachdevices
without turning your system off
Works with DV camcorders, CD-RW/DVD-ROM
drives, scanners, FireWire hard disks, digital
cameras, video game systems and other
audio/video devices
SystemRequirements
•
Pentium® III or equivalent notebook PC with an
available PC Card slot
Windows® 2000/XP (32-/64-bit)/Server 2003 (32-/
64-bit)/Vista (32-/64-bit)
•
04-0461B
1
Hardware Installation
General instructions for installing the card are provided
below. Since the design of notebook computers may
vary, refer to your system’s reference manual for further
information, if needed.
1. Power off your notebook computer and any other
connected peripheral devices.
2. Insert the PC Card into the CardBus Type II slot of
your notebook computer with its 68-pin connector
facing the slot. Make sure it is inserted all the way
in for a solid connection.
3. Power on your notebook computer.
Software Installation
This section provides information on how to install the
FireWire 800 CardBus DV-Kit software.
Windows2000
Windows2000automaticallyinstallsit's built-inFireWire
400driverforthe FireWire800CardBusDV-Kit. Togetthe
full speed out of this controller, install the Firewire 800
driver using the directions below.
1. Insert the driver CD. Click Start, then click Run.
Type D:\setup.exe, click OK. (Change D: to match
your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. Typeinyourcustomerinformation,then clickNext.
5. At the Destination Location screen, click Next.
6.
Select Complete, then click Next.
7. At the Select Program Folder screen, click Next.
3
8. At the Digital Signature screen, click Yes, then click
Finish.
9. SelecttherestartWindowsoption, thenclickFinish.
WindowsXP
Windows XP automatically installs it's built-in FireWire
400 driver for the FireWire 800 CardBus DV-Kit. To get the
full speed out of this controller, install the Firewire 800
driver using the directions below.
1. Insert the driver CD. Click Start, Run. Type
32-bit : Type D:\setup32.exe, click OK. (Change D:
to match your CD-ROM drive letter)
64-bit: Type D:\setup64.exe, click OK. (Change D:
to match your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Select Program Folder screen, click Next.
7. At the Software Installation screen, click Continue
Anyway, then click Finish.
8. SelecttherestartWindowsoption, thenclickFinish.
WindowsServer2003
Windows Server 2003 automatically installs it's
built-in FireWire 400 driver for the FireWire 800 CardBus
DV-Kit. To get the full speed out of this controller, install
the FireWire 800 driver using the directions in the next
page.
4
.
1. Insert the driver CD. Click Start, Run.
32-bit : Type D:\setup32.exe, click OK. (Change D:
to match your CD-ROM drive letter)
64-bit: Type D:\setup64.exe, click OK. (Change D:
to match your CD-ROM drive letter)
2. At the Welcome screen, click Next.
3. At the License Agreement screen, click Yes.
4. At the Destination Location screen, click Next.
5.
Select Complete, then click Next.
6. At the Select Program Folder screen, click Next.
7. At the Security Alert box, click Yes. This step is for
32-bit operating system only.
8. At the Software Installation screen, click Continue
Anyway, then click Finish.
9. SelecttherestartWindowsoption, thenclickFinish.
WindowsVista™
WindowsVistaautomaticallyinstallsit'sbuilt-inFireWire
400 driver for the FireWire 800 CardBus DV-Kit. To get the
full speed out of this controller, install the FireWire 800
driver using the directions below.
1. Insert the driver CD. Click Start, in the Start Search
box.
32-bit : Type D:\setup32.exe, press Enter. (Change
D: to match your CD-ROM drive letter)
64-bit: Type D:\setup64.exe, press Enter. (Change
D: to match your CD-ROM drive letter).
2. Click Allow.
3. At the Welcome screen, click Next.
4. At the License Agreement screen, click Yes.
5. At the Destination Location screen, click Next.
5
6.
Select Complete, then click Next.
7. At the Select Program Folder screen, click Next.
8. At the Windows Security box, click Install three
times, then click Finish.
9. SelecttherestartWindowsoption, thenclickFinish.
VerifyWindowsInstallation
1. Check Device Manger for proper installation.
For 2000/XP/Server 2003: Right click My Computer,
click Manage, then click Device Manager.
For Window Vista: Right click Computer, click
Manage, click Continue, click Device Manager.
2. Double click 1394 Bus host controllers. Unibrain
driver/OHCI Compatible Board should be
displayed.
6
Connecting Devices
General driver installation steps are provided below.
Pleasereviewyourdevice'susermanualformoredetails.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. SelectSearchforasuitabledriver...,thenclickNext.
3. Uncheck all check boxes, then click Next.
4. Click Next, then click Finish.
WindowsXP
1. At the Found New Hardware Wizard.
For XP w/SP2 or later: Select No, not this time, then
click Next.
For XP w/SP1 or earlier: Go directly to step #2.
2. SelectInstalltheSoftwareAutomatically,clickNext.
3. Click Continue Anyway. (Skip if not prompted).
4. Click Finish to complete the installation.
Server2003
1. At the Found New Hardware Wizard.
For2003w/SP1or later: Select No, not this time, then
click Next.
For 2003 no service pack installed: Go to step #2.
2. SelectInstalltheSoftwareAutomatically,clickNext.
3. At the Security Alert box click Yes, or the Hardware
Installation box click Continue Anyway, then click
Finish to complete the installation.
7
WindowsVista™
Windows Vista will automatically detect and install
most FireWire devices when connected. For devices that
do not install automatically, follow the steps below.
Refer to the device's users manual for more information.
1. Click Locate and install driver software.
2. Click Continue to complete the installation.
UleadVideoStudioInstallation
The FireWire 800 CardBus DV-Kit includes Ulead
VideoStudiodigitalvideoeditingsoftwareforproducing
home videos complete with attractive titles, transitions
and sounds.
1. Insert the Ulead VideoStudio DV software CD. The
installation should start automatically. If not, click
Start, Run, type in X:\Autorun.exe, then click OK.
(Replace X: with the drive letter of your CD-ROM)
2. Follow the on-screen instructions to complete.
Note: For instructions on how to use Ulead
VideoStudio, refer to the VStudio.pdf file located
in the Document\Manual directory on the Ulead
VideoStudio DV editing software CD.
8
ubSwitch Utility
In order to use a DV camcorder with this controller,
Microsoft's FireWire 400 driver must be installed in the
system. We have supplied an easy to use utility that
allows switching between Microsoft's driver and the
FireWire 800 driver. Before using this utility, unplug all
devices from the FireWire 800 cardbus.
1. Click Start, Programs, Unibrain ubcore, Tools then
ubSwitch.
2. Right click the ubSwitch icon located in the system
tray by the clock.
3. Click the 1394 adapter that you want to switch, then
click on Microsoft 1394 Drivers.
Note: If your system has multiple 1394 adapters
installed, make sure that you click on the 1394
adapter that the camcorder will be plugged into.
4. Windows will display an information box when the
driver is ready for use. It may take a few seconds for
this box to appear. Wait for this box to appear then
connect your DV camcorder.
Note: To switch back to the FireWire 800 driver,
follow the same procedures, but in step 3 instead of
clickingonMicrosoft1394Drivers, clickonUnibrain
1394 Drivers.
9
ConnectingaDVCamcorder
Before setting up the digital video camcorder, verify the
Microsoft FireWire 400 driver has been successfully
installed in your system, then follow the procedures
below.
1. Connect the 4-pin connector of the provided
FireWire 400 (1394a) DV cable to your camcorder.
2. Connect the 6-pin connector to the FireWire 400
(1394a) port.
3. Power on the camcorder. The camcorder should
appear in Device Manager.
VerifyDVCamcorderSetup
1. Right click My Computer, click Manage, then click
Device Manager.
2. Double click Imaging Device(s), and Microsoft DV
Camera and VCR or DV Camcorder should be
displayed.
10
Technical Support and Warranty
QUESTIONS? SIIG’sOnlineSupporthasanswers! Simplyvisitour
database is updated daily with new drivers and solutions. Answers
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
request to SIIG RMA. If the product is determined to be
defective,anRMAnumberwillbeissued. SIIGRMAdepartment
can also be reached at (510) 413-5333.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA#:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
11
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,andthroughe-commercesites.
PRODUCT NAME
FireWire 800 CardBus DV-Kit
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
FireWire 800 CardBus DV-Kit is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered
trademarksofSIIG,Inc. Microsoft,WindowsandWindowsVistaareeitherregisteredtrademarksor
trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a
registeredtrademarkofIntelCorporation. Othernamesusedinthispublicationareforidentification
onlyandmaybetrademarksoftheirrespectivecompanies.
January, 2008
Copyright © 2008 by SIIG, Inc. All rights reserved.
|