Owner’s Manual
■ Before using this unit, carefully read the sections entitled:
“USING THE UNIT SAFELY” and “IMPORTANT NOTES”
(Page 4–5; Page 6–8). These sections provide important
information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a
good grasp of every feature provided by your new unit,
Owner’s Manual should be read in its entirety. The manual
should be saved and kept on hand as a convenient reference.
Copyright © 2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any
form without the written permission of ROLAND CORPORATION
Other Recording
Methods
Using [MARKER] to assign track numbers................................................................ 55
Erasing All Tracks...................................................................................................... 58
Formatting a CF Card................................................................................................ 63
More Functions
Erasing the Last Track............................................................................................... 64
Erasing All Tracks...................................................................................................... 64
Changing the Tuner’s Reference Pitch...................................................................... 67
■ Other Functions and Settings................................................................... 75
Displaying the Remaining Time................................................................................. 75
Adjusting the Output Level from the AUX OUT Jacks ............................................... 77
Switching the Line Input On/Off................................................................................. 78
Viewing the Track Titles on a CF Card...................................................................... 78
Adjusting the Playback Level of a Music CD/CF Card............................................... 79
Reference
3
Introduction
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the power-
cord plug must be unplugged from the outlet.
•
001 Before using this unit, make sure to read the
•
008cBe sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified on
the AC adaptor’s body. Other AC adaptors may
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
instructions below, and the Owner’s Manual.
..........................................................................................................
•
002cDo not open (or modify in any way) the unit or its
AC adaptor.
..........................................................................................................
..........................................................................................................
003 Do not attempt to repair the unit, or replace parts
008e
•
•
Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
..........................................................................................................
•
009 Do not excessively twist or bend the power cord,
distributor, as listed on the “Information” page.
..........................................................................................................
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements
and short circuits. Damaged cords are fire and
shock hazards!
•
004 Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
..........................................................................................................
•
010 This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
007 Make sure you always have the unit placed so it is
..........................................................................................................
•
•
011 Do not allow any objects (e.g., flammable
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the unit.
..........................................................................................................
4
012b
101b
•
Immediately turn the power off, remove the AC
•
The unit and the AC adaptor should be located so
adaptor from the outlet, and request servicing by
your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on
the “Information” page when:
their location or position does not interfere with
their proper ventilation.
..........................................................................................................
102cAlways grasp only the plug on the AC adaptor
•
• The AC adaptor, the power-supply cord, or the
plug has been damaged; or
cord when plugging into, or unplugging from, an
outlet or this unit.
• If smoke or unusual odor occurs
..........................................................................................................
103b
• Objects have fallen into, or liquid has been
spilled onto the unit; or
•
At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor insulation
and lead to fire.
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally
or exhibits a marked change in performance.
..........................................................................................................
013 In households with small children, an adult
•
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
•
104 Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
014 Protect the unit from strong impact.
•
..........................................................................................................
•
106 Never climb on top of, nor place heavy objects on
(Do not drop it!)
..........................................................................................................
015 Do not force the unit’s power-supply cord to
the unit.
•
..........................................................................................................
•
107cNever handle the AC adaptor or its plugs with
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
108b
•
Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..........................................................................................................
016 Before using the unit in a foreign country, consult
..........................................................................................................
110b
•
•
Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
..........................................................................................................
118a
•
Should you remove screws, keep them in a safe
place out of children’s reach, so there is no chance
of them being swallowed accidentally.
..........................................................................................................
•
120 Always turn the phantom power off when
connecting any device other than condenser mic
that require phantom power. You risk causing
damage if you mistakenly supply phantom power
to dynamic mics, audio playback devices, or other
devices that don’t require such power. Be sure to
check the specifications of any mic you intend to
use by referring to the manual that came with it.
(This instrument’s phantom power: 48 V DC, 10mA Max)
..........................................................................................................
5
Introduction
IMPORTANT NOTES
• If you place the unit on a piano or an item of furniture, the
rubber feet of this unit may discolor or damage the finish
of the piano. To prevent the rubber feet from causing this
type of problem, place a cloth under the unit.
Power Supply
301
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
Maintenance
401a
appliance is used, power supply noise may cause this unit
• For everyday cleaning wipe the unit with a soft, dry cloth
to malfunction or may produce audible noise. If it is not
or one that has been slightly dampened with water. To
practical to use a separate electrical outlet, connect a
remove stubborn dirt, use a cloth impregnated with a
power supply noise filter between this unit and the
mild, non-abrasive detergent. Afterwards, be sure to wipe
electrical outlet.
the unit thoroughly with a soft, dry cloth.
302
402
• The AC adaptor will begin to generate heat after long
• Never use benzine, thinners, alcohol or solvents of any
hours of consecutive use. This is normal, and is not a
kind, to avoid the possibility of discoloration and/or
cause for concern.
deformation.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
Additional Precautions
552
• Unfortunately, it may be impossible to restore the contents
of data that was stored on a CompactFlash or CD-R/RW
disc once it has been lost. Roland Corporation assumes no
liability concerning such loss of data.
Placement
351
• Using the unit near power amplifiers (or other equipment
553
containing large power transformers) may induce hum.
• Use a reasonable amount of care when using the unit’s
To alleviate the problem, change the orientation of this
buttons, sliders, or other controls; and when using its jacks
unit; or move it farther away from the source of
interference.
and connectors. Rough handling can lead to malfunctions.
554
352a
• Never strike or apply strong pressure to the display.
• This device may interfere with radio and television
556
• When connecting / disconnecting all cables, grasp the
reception. Do not use this device in the vicinity of such
receivers.
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or
initiating a call, or while conversing. Should you
experience such problems, you should relocate such
wireless devices so they are at a greater distance from this
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559a
unit, or switch them off.
• When you need to transport the unit, package it in the box
***
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
• Observe the following when using the unit’s CD-R/RW
562
• Use a cable from Roland to make the connection. If using
- Install the unit on a solid, level surface.
some other make of connection cable, please note the
following precautions.
- Do not move the unit or subject it to vibration while
the drive is operating.
- Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For infor-
mation on cable specifications, contact the manufac-
turer of the cable.
354a
• Do not expose the unit to direct sunlight, place it near
devices that radiate heat, leave it inside an enclosed
vehicle, or otherwise subject it to temperature extremes.
Excessive heat can deform or discolor the unit.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
6
Handling CompactFlash Cards
Handling CD-R/RW Discs
***
704
• Carefully insert the CompactFlash card all the way in—
• DO NOT play a CD-R/RW disc (CD-R/RW disc on which
track data from a CompactFlash card has been backed up
until it is firmly in place.
fig.M512-Insert
resulting sound may be of a level that could cause
permanent hearing loss. Damage to speakers or other
system components may result.
***
• Don’t use unusually shaped discs, such as heart-shaped or
octagonal discs. Doing so may damage the CD-2.
• Do not bend the disc.
***
• Do not drop or stack discs.
***
• Do not place heavy objects on a disc, or subject it to strong
physical shock.
(•801Hchaonlgde)a disc by inserting a finger in the center hole and
pressing your thumb against the outer edge. Be careful not
to get fingerprints on, or scratch the recording surface of
the disc (the green surface).
705
• Never touch the terminals of the CompactFlash card. Also,
avoid getting the terminals dirty.
707
• This unit’s memory card slot accepts the CompactFlash
card. Microdrive storage media are not compatible.
708
• CompactFlash cards are constructed using precision
components; handle the cards carefully, paying particular
note to the following.
- To prevent damage to the cards from static electricity,
be sure to discharge any static electricity from your
own body before handling the cards.
***
- Do not touch or allow metal to come into contact with
the contact portion of the cards.
• Do not use in dusty areas.
***
• Do not leave the disc in direct sunlight or an enclosed
- Do not bend, drop, or subject cards to strong shock or
vibration.
vehicle.
***
- Do not keep cards in direct sunlight, in closed vehicles,
or other such locations (storage temperature: -25 to 85˚
C).
• Do not keep the disc in the CD-R/RW drive for a long
time.
***
• To protect the disc, keep it in its original case.
- Do not allow cards to become wet.
***
- Do not disassemble or modify the cards.
• Do not put a sticker on the label of the disc.
***
• When writing a title on the label surface of the disc, use a
soft-tipped writing implement such as a felt pen.
***
Handling the CD-R/RW Drive
• Wipe the disc with a soft and dry cloth radially from
***
inside to outside. Do not wipe along circumference.
• Install the unit on a solid, level surface in an area free from
vibration.
***
• Never use the emergency eject hole to open the disc tray
while the this unit is operating.
***
• Remove any disc from the drive before powering up or
down.
***
•
When you carry this unit, remove the disc from the
loading tray.
***
• To avoid the risk of malfunction and/or damage, insert
only discs with into the CD-R/RW drive. Never
(•801Kcheanegpe)your discs clean using a commercially available CD
cleaner. Do not use benzine, record cleaner spray or
insert any other type of disc. Avoid getting paper clips,
coins, or any other foreign objects inside the drive.
solvents of any kind.
***
• Please read the documentation that is included with your
CD-R/RW discs.
7
Introduction
IMPORTANT NOTES (continued)
Copyright
8•51 Unauthorized recording, distribution, sale, lending, public
performance, broadcasting, or the like, in whole or in part,
of a work (musical composition, video, broadcast, public
performance, or the like) whose copyright is held by a
third party is prohibited by law.
(852a)
• This unit is designed for professional use. When using the
CD-R/RW drive to transfer audio signals, this unit can
perform recording without being subject to the restrictions
of the Serial Copy Management System (SCMS). This is
because the unit is intended solely for musical production,
and is designed not to be subject to restrictions as long as
it is used to record works (such as your own
compositions) that do not infringe on the copyrights of
others. (SCMS is a feature that prohibits second-
generation and later copying through a digital connection.
It is built into MD recorders and other consumer digital-
audio equipment as a copyright-protection feature.)
8•53 Do not use this unit for purposes that could infringe on a
copyright held by a third party. We assume no
responsibility whatsoever with regard to any
infringements of third-party copyrights arising through
your use of this unit.
About the License Agreement
***
• The CD-2’s CD-writing functionality, and its copying
functionality are designed to allow you to reproduce
material to which you have copyright, or material which
the copyright owner has granted you permission to copy.
Accordingly, reproduction of Music CD or other
copyrighted material without permission of the copyright
owner avoiding technical prohibiting features of second-
generation and later copying like SCMS or others
constitutes copyright infringement and may incur
penalties even in case such reproduction is for your own
personal use and enjoyment (private use). Consult a
copyright specialist or special publications for more
detailed information on obtaining such permission from
copyright holders.
8
Introduction
Check the Included Items
Check the CD-2 package to make sure it includes these items.
❑ CD-2
❑ Blank CD-R disc
: 700MB
❑ CompactFlash
(CF card): 128MB
* The card is already
formatted.
❑ AC Adaptor
(PSB-3U)
❑ Card Protector
(attached to the bottom
of the CD-2)
❑ Power Cord
❑ Owner’s Manual
❑ Leaflet (“Record Your
Performance and
Create a CD”)
9
Introduction
Main Features
Easily create an original music CD using only the CD-2
You can record on three types of media.
CompactFlash
(CF cards)
CD-R discs
CD-RW discs
●
●
You can create a music CD from selected songs recorded on a CompactFlash card.
You can create a music CD by directly recording onto a CD-R/RW disc.
Easily record using the internal mics, and listen back using the
built-in speakers
●
Since stereo mics are built in, you can start recording immediately.
For hands-free operation, there’s an “Auto Level Control” function which automatically adjusts the input
●
Since stereo speakers are built in, you can listen to your recordings right away.
Connect mics or instruments to directly record a vocal or
instrumental performance
●
You can directly record a performance from mics or instruments (e.g., guitar or digital piano) connected
to the input jacks.
The CD-2 provides external mic jacks, a guitar input jack to which a guitar or bass can be connected directly, and line
input jacks.
Use mix-recording for even greater possibilities
●
You can layer your own vocal or instrumental performance with a song from a music CD.
While listening to the accompaniment provided by a karaoke CD, you can add your own vocal or instrumental
performance and record the result to a CompactFlash card.
●
Songs you’ve recorded on a CompactFlash card can be layered with additional performances.
You can build up multi-part instrumental or vocal performances by yourself. For example, while listening to a piano
accompaniment you’ve previously recorded, you could mix in an additional vocal performance.
10
Convenient practice functions for music lessons
●
●
●
You can slow down the playback speed without affecting the pitch of a song.*
You can change the playback pitch (key) of a song.*
You can remove the vocal from the playback of a CD.*
The CD-2 provides a Center Cancel function that can eliminate much of the main vocal part from a CD so it becomes
less noticeable. This lets you use your favorite CDs as karaoke CDs.
●
You can repeatedly play back a desired section.
The A-B Repeat function lets you play back a specified section repeatedly.
* These functions are available only for CD.
Easy editing with CompactFlash
●
You can delete unwanted regions of silence that were recorded before or after the song, or divide a song
as desired.
Versatile built-in effects
You can process your vocal or instrumental performances by applying a variety of effects.
The CD-2 provides a wide range of effects for a variety of applications, such as for vocals or for guitar/bass.
●
You can make a professional-sounding CD.
The CD-2 provides mastering effects that can add a professional-sounding final touch to your music CD.
●
11
Introduction
Panel Descriptions
Top Panel
EDIT Button
Internal Speakers/Internal Mics
Use this button when you want to edit the tracks of a CF
card.
Stereo Speakers
These are a pair of stereo speakers built into the CD-2.
MIC L/MIC R
Stop ( ) Button
These are a stereo pair of mics built into the CD-2. You can
use these mics to record.
Press this button to stop playback or recording.
Play/Pause (
) Button
Press this button to start playback or recording.
During playback or recording, you can press this button to
pause. Press it once again to resume playback or recording
from the location at which you paused.
If you pause recording, the next track will be started at the
point you resume recording.
CompactFlash Operation Area
Use the controls in this area for operations on a
CompactFlash (CF card).
OVERDUBBING Button
Record ( )/MARKER Button
● Press this button to enter recording-standby mode for
Use this button when you want to play back a track (song)
from a music CD or CF card while overdubbing (layering)
an additional a vocal or instrumental performance.
a CF card.
from a Music CD”
from a CF Card”
● During recording, you can press this button to assign a
track number.
12
CD WRITE Area
COMPACT DISC Operation Area
The controls in this area let you create a music CD from
CF card tracks.
The controls in this area let you control the CD-R/RW disc
or music CD.
MASTERING Button
PITCH Button
This button lets you apply mastering effects to tracks on
the CF card.
●
You can use this button to adjust the pitch (fine
adjustments of less than a semitone) of the CD playback.
Pitch”
TRACK SELECT Button
This button lets you select the CF card tracks that you want
to write to a CD-R/RW.
● You can use this button to transpose the key
(adjustments of a semitone) of the CD playback.
SPEED Button
WRITE Button
This button plays the CD slowly without affecting its pitch.
This button writes the selected CF card tracks to a CD-R/
RW disc.
CENTER CANCEL Button
This button lets you eliminate (or reduce) the main vocal
or lead guitar sound from a CD.
CF Card/CD Common Area
Playback”
The controls in this area let you control the media (CF
card or CD) that you’ve selected as the source.
ERASE Button
This button lets you erase previously recorded tracks from
a CD-RW disc, or to “un-finalize” a disc.
Previous track/Next track (
/
) Buttons
] Buttons
/
Rewind/Fast-forward (
● You can use these buttons to jump to the beginning of
FINALIZE Button
the preceding or the following track. During playback,
the [Previous track(
beginning of the currently playing track.
)] button takes you back to the
This button finalizes a CD-R/RW disc that you’ve finished
recording.
● While stopped, press and hold these buttons to rapidly
Player”
move to the beginning of the track.
● During playback, press and hold one of these buttons
EJECT ( ) Button
to rewind or fast-forward.
This button opens or closes the disc tray.
● While paused, press and hold these buttons to rapidly
rewind or fast-forward.
Stop ( ) Button
REPEAT: 1/ALL Button
● This button repeatedly plays one track or all tracks.
This button stops playback from or recording.
Tracks”
Play/Pause (
This button starts playback or recording.
) Button
During playback or recording, you can press this button to
pause. Press it once again to resume playback or recording
from the location at which you paused.
If you pause recording, the next track will be started at the
point you resumed recording.
● When assigning a title a CF card track, this button
enters a space between characters of the title.
REPEAT: A-B Button
● This button repeatedly plays back the region you
specify.
Record ( )/MARKER Button
● Press this button to enter recording-standby mode for
Section”
the CD-R/RW disc.
● During recording, you can press this button to assign a
● When assigning a title a CF card track, this button
track number.
deletes a character from the title.
13
Introduction
Panel Descriptions (continued)
Side Panel (CompactFlash Slot)
Display
MIC 1/MIC 2 Jacks
Mics with XLR-type plugs can be connected to these jacks.
The display shows various information or messages
related to the operation you’re performing, such as when
making various settings or editing tracks.
LEVEL Meter
Security Slot (
)
This indicates the volume level of the track that’s playing
or the instrument or mic that’s being input.
You can attach a commercially available security lock
here.
Source Name Indication
PHANTOM Power Supply Switch
This switch supplies phantom power to the XLR-type
MIC 1/MIC 2 jack.
This indicates the name of the currently selected audio
source.
TRACK Indication
This indicates the track number.
CompactFlash (CF Card) Slot
You can insert a CompactFlash (CF) card here.
TIME Indication
● This indicates the elapsed playback or recording time.
You can switch the time information that is shown
here.
If desired, you can attach the included card protector to
prevent theft of the CF card.
● The track titles of a CF card will be scrolled here.
Card Eject Button
Use this button to eject the CF card.
Icon Indications
● Functions specific to a CD
Displayed when the playback pitch is being
CD-R/RW Drive
altered.
Displayed when the key is being altered.
Displayed when the playback speed is being
Displayed when the Center Cancel function is
on. Page 42
● Functions common to both CD and CF
Disc Tray
Place the CD in this tray.
Displayed during 1-track repeat playback.
CD
Displayed during all-track repeat playback.
Displayed during A-B repeat playback.
Emergency Eject Hole
You can use this to remove the disc in case of emergency.
Normally, it is not used.
14
Front Panel
MIC SELECT Button
MIC 1/GUITAR Knob
This selects the audio input source that will be recorded.
This adjusts the input level of the MIC 1 jack or the
GUITAR jack.
EFFECT Button
This button applies an effect to the audio input source.
MIC 2 Knob
This adjusts the input level of the MIC 2 jack.
TUNER Button
GUITAR Jack
● Press this button to enter Tuner mode.
You can connect an electric guitar or bass to this jack. Since
this is a high-impedance jack, you can connect a guitar or
bass directly.
● You can use this button to sound a reference pitch.
MIC 1/MIC 2 Jacks
DATA Dial
Mics with phone plugs can be connected to these jacks.
● Use the dial to adjust the value of the setting shown in
the display.
METRONOME Button
● When assigning titles to CF card tracks, use the dial to
● This button sounds the metronome.
choose characters.
● You can use this button to specify a count-in.
ENTER Button
Press this to answer “yes” to messages shown in the
display.
Timing”
MENU Button
EXIT Button
Use this button to access various functions and settings,
such as those for adjusting the display contrast or selecting
the recording mode.
Press this to answer “no” to messages shown in the
display.
Also, this button is pressed to return to a previous screen
after you’ve modified a setting.
PHONES Jack
You can connect a set of headphones to this jack.
SPEAKER MUTE Button
This button temporarily silences the internal speakers.
OUTPUT LEVEL Knob
This knob adjusts the volume of the internal speakers and
the headphones.
15
Introduction
Panel Descriptions (continued)
Rear Panel
POWER Switch
AUX OUT Jacks
This turns the power on/off.
Use these jacks to output analog audio signals to an
external speaker system or electronic piano.
AC Adaptor Jack
You can choose the type of audio signal that is sent from
the AUX OUT jacks.
Connect the included AC adaptor to this jack.
Cord Hook
Wrap the AC power adaptor cord around this hook to
prevent the cord from being accidentally unplugged.
LINE IN Jacks
You can connect your electronic piano or keyboard to
these jacks, and record your performance.
Adaptor Jack”
FOOT SW (Foot Switch) Jack
LEVEL Knob
You can connect a foot switch (such as the Roland DP-2 or
BOSS FS-5U; separately available) to this jack. Use it to
play back, record, or assign track numbers.
This knob adjusts the input level of the LINE IN jacks.
MIDI OUT Connector
This connector transmits MIDI messages.
● If you want to play back SMF (Standard MIDI File)
data, connect this jack to the MIDI IN connector of
your external sound generating device.
16
Introduction
Media That Can Be Used with the CD-2
As its recording media, the CD-2 uses CompactFlash cards (CF cards) and CD-R/RW discs. The functions available for editing or
deleting songs (tracks) after recording will differ according to the media you use.
The table below shows the functions that can be used with each type of media.
Media
CF card
CD-R disc
CD-RW disc
Music CD
4x speed
supported
4x/8x speeds
supported
Logo (use a disc bearing one of the logos below)
CD-2 function
Recording
Playback
Conventional recording
Overdubbing
OK
OK
OK
OK
OK
OK
OK
Record mode selection
Conventional playback
Repeat playback
OK
OK
OK
OK
OK
OK
Special playback (Slow/Pitch/
Key/Center Cancel)
OK
OK
OK
OK
OK
SMF (Standard MIDI File) playback
Edit tracks
OK
OK
Delete tracks
OK
OK
OK
OK
OK
Cancel finalization
Create an original music CD
Back up a CF card
OK
OK
OK
Copy an original music CD
• We cannot guarantee that a music CD created on the CD-2 will play on all CD players. Depending on your CD player’s support
for CD-R/RW discs, music CDs you create may not play correctly.
• Even if a disc bears an appropriate logo, recording or playback may not be possible depending on the state of the disc.
• For details on how to handle CF cards and CD-R/RW discs, refer to the instructions that came with the media you’re using.
• We cannot guarantee that special discs not conforming to the music CD specification (e.g., “copy-control CDs” or “copy-guard
CDs”) will play. When using the CD-2 to play a music CD, please carefully read any statements printed on the CD package.
MEMO
•
•
About CD-R discs
Use CD-R discs that support 8x speed.
Example:
2-48x speed, 1-32x speed
About CD-RW discs
Use CD-RW discs that support 4x speed or 8x speed.
(CD-RW discs that support ultra-speed or ultra-speed plus cannot be used.)
Example:
multi-speed CD-RW discs:
High-speed CD-RW discs:
1-4x speed, 4x speed
4-10x speed, 4-12x speed
17
Notes Regarding CompactFlash (CF) Cards
In this manual, CompactFlash cards are referred to as “CF
cards.”
■
Recording Modes and Maximum Recording Times
When using a CF card for recording, you can select one of
three recording modes as appropriate for the desired
You can purchase CF cards at your local computer dealer or at
a store that handles digital cameras.
recording time and audio quality (
The following table shows the maximum recording times
possible with each recording mode on various capacities
of media.
■ Specifications
● Supported capacities:
Maximum recording time (approx.)
16 MB, 32 MB, 64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB
Capacity
Recording mode
● CF Type II card is not compatible.
Standard
Long
WAV
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
3 minutes
6 minutes
1.5 minutes
■ Recommended CF Cards
SanDisk, Kingston
6 minutes
12 minutes
24 minutes
49 minutes
98 minutes
12 minutes
24 minutes
49 minutes
98 minutes
3 minutes
6 minutes
12 minutes
24 minutes
• Even if recommended CF cards are used, there may be
cases in which they will not operate correctly.
■ Formatting a CF Card
196 minutes 49 minutes
A newly purchased CF card or one previously used in a
computer or digital camera may need to be formatted
before it can be used with the CD-2.
196 minutes 392 minutes 98 minutes
392 minutes 784 minutes 196 minutes
2 GB
• The maximum times given above are approximate. The
actual time may be slightly less depending on how tracks
have been edited.
■ Regarding the CF Card Protector
You can attach the included card protector in front of the
CF card slot. This will block the CF card slot, preventing
the CF card from being stolen.
• You can view the remaining time in the display.
• Tracks using differing recording modes may be recorded
on a single CF card.
Notes Regarding CD-R/RW Discs
■ Recommended Manufacturers: CD-R Discs
■ Maximum Recording Times
Taiyo Yuden Corp., Mitsubishi Chemical Corp.,
Ricoh Corp., Hitachi Maxell Corp.
Capacity
650 MB
700 MB
Maximum recording time
approximately 74 minutes
approximately 80 minutes
■ Recommended Manufacturers: CD-RW Discs
• The maximum times given above are approximate. The
actual time may be slightly less depending on the number
of tracks that are recorded.
Mitsubishi Chemical Corp., Ricoh Corp.,
Hitachi Maxell Corp.
• Even if recommended CD-R/RW discs are used, there
may be cases in which they will not operate correctly.
• You can view the remaining time in the display.
• CD-RW discs that support ultra-speed or ultra-speed plus
cannot be used.
18
Attaching the Card Protector
You can attach the included card protector in front of the CF card slot to block the slot and prevent theft of the CF
card.
To attach the card protector, proceed as follows.
Turn off the CD-2 and all connected equipment.
1
• Disconnect all cables from the CD-2.
NOTE
Turn the CD-2 upside down, and remove the card
protector.
2
When turning the CD-2 upside
down, place stacks of newspapers
or magazines to support the four
corners (or two sides) so that
stress is not placed on the buttons
or knobs, possibly damaging
them. Then, carefully position the
CD-2 in such a way that its
buttons and knobs won’t get
damaged.
Handle the CD-2 with care, and
avoid dropping it.
Card protector
MEMO
If you’re not using the card
1 Use a Philips (+) screwdriver to remove the two
protector
screws shown in the illustration.
To prevent the card protector
from being lost, leave it fastened
in its original location (shown in
the illustration for Step 2).
2 Pull out the card protector in the direction
indicated by the arrow.
MEMO
Don’t overtighten the screws,
since this may strip the threads
and even damage the CD-2.
Position the card protector as shown in the
illustration, and fasten it in place using the two
3
4
1
screws you removed in Step 2 -
.
Turn the CD-2 right side up.
19
Introduction
Connecting Other Equipment
NOTE
• To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power
on all devices before making any connections.
● Front Panel
Electric guitar
Electric bass
Mic
Headphones
● Side Panel
● Rear Panel
Foot switch
AC adaptor
(PSB-3U: included)
R
L
To analog output jacks
R
L
To analog input jacks
AC cord
(Included)
To MIDI IN connector
To power outlet
Amp, audio set, etc.
Electronic piano, keyboard, etc.
MIDI sound module, etc.
20
Cautions When Making Connections
AC Adaptor Jack
MIC 1/MIC 2 Jacks
• To prevent the inadvertent disruption of power to your
unit (should the plug be pulled out accidentally), and to
avoid applying undue stress to the AC adaptor jack,
anchor the power cord using the cord hook, as shown in
• This instrument is equipped with balanced (XLR/TRS)
type jacks. Wiring diagrams for these jacks are shown
below. Make connections after first checking the wiring
diagrams of other equipment you intend to connect.
the illustration.
fig.CordHook.e
Cord hook
Rear panel
• Howling could be produced depending on the location
of mics relative to speakers. This can be remedied by:
The cord of the supplied AC adaptor
1. Changing the orientation of the mic(s).
2. Relocating mic(s) at a greater distance from
speakers.
3. Lowering volume levels.
Connection Cables
• You must not connect a mic to both MIC jacks (XLR-type
and phone-type) of the same number. Doing so will
damage the mic and/or the CD-2.
• When connection cables with resistors are used, the
volume level of equipment connected to the inputs (MIC
1, MIC 2, GUITAR, LINE IN) may be low. If this
happens, use connection cables that do not contain
resistors, such as those from the Roland PCS-series.
MIC 1
MIC 1
MIC 2
MIC 2
Foot Switch
• If cables are plugged into both the MIC 1 (XLR-type or
phone-type) and the GUITAR jack, the input from MIC 1
jack will be cancelled.
• If you are using a Boss FS-5U, set the polarity switch of
the FS-5Uas shown in the illustration.
or
Priority
Priority
Polarity switch
21
Introduction
Connecting Other Equipment (continued)
Connecting Condenser Mics
If you’re using condenser mics, you must make settings so
that phantom power is supplied to them.
NOTE
• Supplying phantom power to a dynamic mic or an audio
playback device will cause malfunctions. Also, the CD-2
cannot be used with devices other than condenser mics
that require phantom power (such as the BOSS Direct
Box DI-1).
Carefully read the owner’s manual for the mic you’re
using, and be sure to set the phantom power switch
to “OFF” unless you are using a condenser mic that
requires phantom power.
Connecting a mic to the XLR type MIC 1
(or MIC 2) jack
1
MEMO
• Phantom power is not supplied to the phone type MIC 1
jack and MIC 2 jack located on the front panel. If your
mic requires phantom power, you must connect the mic
to the XLR type MIC 1 jack (or MIC 2 jack) located on the
side panel.
Turn on the power of the CD-2.
2
Slide the phantom power switch located
on the side panel toward the right to the
“ON” position.
3
Phantom power switch
22
Basic Operation
This section explains how to carry out basic CD-2 procedures, from recording and playback through
creating a music CD.
Turning the Power On/Off.................................................................................... 24
Adjusting the Screen Contrast............................................................................. 25
Getting Started
Adjusting the Volume........................................................................................... 25
Recording
to CF/CD
■
■
■ Settings for Recording ......................................................................... 36
Choosing the CF Card Recording Mode.............................................................. 36
Changing the Key of the Playback (Key)............................................................. 42
Repeatedly Playing a Section (A-B Repeat)........................................................ 43
Playback
Repeatedly Playing a Section (A-B Repeat)........................................................ 45
Creating a
Music CD
23
Getting Started
Basic Operation
Turning the Power On/Off
Turning the Power On
If Other Equipment is Connected to the
CD-2
NOTE
• Once the connections have been completed (
specified. By turning on devices in the wrong order, you
risk causing malfunction and/or damage to speakers
and other devices.
Make sure that the device connected to the
CHECK
AUX OUT jack is powered off.
• This unit is equipped with a protection circuit. A brief
interval (a few seconds) after power up is required
before the unit will operate normally.
Minimize the volume of all connected
devices.
1
If No Other Equipment is Connected to
the CD-2
Turn
counterclockwise to
“MIN” (minimum).
2
3
Turn
counterclockwise to
“MIN” (minimum).
1
2
On the rear panel, press
.
The power turns on. Once the power is on, the screen
lights up.
On the rear panel, press
.
The power turns on. Once the power is on, the screen
lights up.
Power up the device connected to the
AUX OUT jack.
4
Turning the Power Off
If No Other Equipment is Connected to
the CD-2
If Other Equipment is Connected to the
CD-2
Turn
counterclockwise to
“MIN” (minimum).
Switch off the power on all connected
equipment.
1
2
1
On the rear panel, press
.
Turn
counterclockwise to
“MIN” (minimum).
2
3
The power turns off.
On the rear panel, press
.
The power turns off.
24
Adjusting the Screen Contrast
Temporarily Muting the Sound
(Speaker Mute)
If you’ve been using the CD-2 for an extended time, or
because of external temperature conditions, the characters in
the screen may seem difficult to read. If this occurs, you can
adjust the contrast for best visibility.
You can mute the sound of the internal speakers simply by
pressing a button.
For example, you might find this convenient when you need
to answer the telephone.
Press
until “LCD Contrast” appears
1
in the display, and then press
.
Press
.
1
2
• You can also select this item by turning [DATA].
The following screen appears.
The button lights, and the internal speaker is silenced.
• The sound from the headphones is not silenced.
When you want to once again hear the
sound, press
again.
Turn
to adjust the LCD contrast.
2
3
The button goes out, and the volume returns to the
previous setting.
• You can adjust this in a range of 1–10.
MEMO
• If you’re recording via the internal mic ([MIC SELECT] is
internal speaker during recording-standby mode or
while recording, and [SPEAKER MUTE] will light
automatically. This ensures that the sound being heard
from the internal speakers will not be recorded by the
internal mics.
Press
twice.
You’re returned to the previous readout.
HINT
• You can also adjust the LCD contrast by holding down
[MENU] and turning [DATA].
Adjusting the Volume
Turn [OUTPUT LEVEL] to adjust the volume of the CD-2’s
speakers and headphone jack.
softer
louder
MEMO
• If the AUX OUT level is set to “Variable” (
you can use [OUTPUT LEVEL] to adjust the output level
of the AUX OUT jacks.
25
Getting Started
Inserting/Removing a CD
Inserting a Disc
Removing a Disc
Press
.
Press
.
1
2
1
The disc tray opens.
The disc tray opens.
Place the disc on the disc tray.
Remove the disc.
2
3
Place with the label surface
facing upward
Press
once again.
The disc tray closes.
• You can also close the disc tray by gently pressing
the front of the disc tray.
Disc tray
Press
once again.
3
If the Disc Tray Doesn’t Open
The disc tray closes.
If pressing [EJECT ( )] fails to open the disc tray, you can
forcibly open the tray by pushing a straightened paper clip
into the emergency eject hole.
• You can also close the disc tray by gently pressing
the front of the disc tray.
• You can also close the disc tray by pressing
the CD side. When the disc is detected, playback
will begin automatically.
on
NOTE
•
Never use the emergency eject hole to open the disc
tray while the CD-2 is operating.
• When the disc has been detected, “CD” is indicated
as the audio source name.
Switch off the CD-2’s power.
1
Source name
In the case of a previously recorded disc or a music
CD, the total number of songs and the total
playback time will be displayed when this
information has been read from the disc.
Push a straightened paper clip (or similar
object) into the emergency eject hole.
2
Total number of tracks Total playback time
Emergency eject hole
The disc tray is ejected forcibly.
Pull out the disc tray, and remove the disc.
Push the disc tray closed.
3
26
Getting Started
Inserting/Removing a CF Card
Inserting a CF Card
Removing a CF Card
NOTE
• The CD-2’s power must be turned off before removing a
CF card. Keep the CF card inserted while the CD-2’s
power is turned on.
Insert the CF card into the CF card slot.
1
Carefully insert the CF card all the way in—until it is
firmly in place.
If a CF card is removed while the CD-2’s power is on, the
data in the CF card may be destroyed, or the CF card
may become unusable.
Switch off the CD-2’s power.
1
Press the card eject button located at the
right of the CF card slot.
CF card slot
2
•
If the CF card cannot be used in its current state
by the CD-2
The card eject button pops out.
The message “Not CD-2 Format. Format?” appears.
In order to use this CF card with the CD-2, you will
need to format it.
Card eject button
•
If the CF card has already been formatted
When the CD-2 recognizes the CF card, “CF” is
indicated as the source name.
Press the card eject button once again.
3
4
• Press the button in until you hear a click.
The CF card pops out slightly.
Grasp the CF card and pull it straight out.
NOTE
Source name
In the case of a previously recorded CF card, the
total number of songs and the total playback time
will be displayed when this information has been
read from the CF card.
• The card eject button may be damaged if you leave it in
the outward position; be sure to push it back in.
Total number of tracks Total playback time
27
Recording to CF/CD
Recording on the CD-2
Three Methods of Recording
Broadly speaking, there are three methods of recording on the CD-2.
■ Recording with the CD-2’s internal mics (
Media that you can record to
CD-R
discs
CD-RW
discs
Recording
CF cards
■ Recording from a Connected Mic or Instrument (
Media that you can record to
CD-R
discs
CD-RW
discs
Recording
CF cards
■ Layering a performance with the playback of a music CD or CF card (Overdubbing)
1 Layering a performance with a song from a music CD (
For example, if you play back a karaoke CD and sing along, the karaoke accompaniment and your voice will be recorded
together.
2 Layering a performance with a song recorded to a CF card (
For example, let’s suppose you’ve recorded a piano performance onto a CF card. Then, while playing back the recorded
piano performance, you can sing along and record the piano performance and your vocal together. A new song containing
the piano and vocal will be created on the CF card.
Playing
Music CD
1
2
Media that you
can record to
Recording
CF cards
or
CF card
28
Cautions When Recording on
a CF Card or CD-R/RW Disc
When Recording on a CF card (continued)
■ Recording Time for One Track (One Song)
■
Minimum Recording Rime for One Track
The maximum length of one track is three hours.
Each track on a music CD must be at least four seconds
long. Since the CD-2 creates music CDs from the songs you
record, it does not allow you to record a track that is less
than four seconds long.
If a recording exceeds three hours, a new track division
will automatically be created.
■
The Number of Recording Tracks for One CF Card
A maximum of 99 tracks can be recorded on one CF card.
Pressing [Stop ( )] or [Pause (
)] will not stop
recording if less than four seconds have passed since you
began recording. Moreover, you cannot assign a track
When Recording on a CD-R/RW disc
■ In Case Your Performance is Not Recordable
Further recording is not possible once you have reached
the maximum recordable time or the maximum number of
songs that can be recorded.
■ Maximum Recording Times
Capacity
650 MB
700 MB
Maximum recording time
approximately 74 minutes
approximately 80 minutes
• If there is no more recordable time, the message “CF Card
Full” or “CD Disc Full” will appear.
• The maximum times given above are approximate. The
actual time may be slightly less depending on the number
of tracks that are recorded.
• If the maximum number of tracks have already been
recorded, the message of “CF Track Full” or “CD Track
Full” will appear.
This message goes away when you press [ENTER].
• You can view the remaining time in the display.
If you’re using a CF card or a CD-RW disc, you can erase
recording.
■ Types of Discs that You Can Record
CD-R discs
• Blank CD-R discs
• Partially recorded (not yet
finalized) CD-R discs
When Recording on a CF card
CD-RW discs
• Blank CD-RW discs
■
Recording Modes and Maximum Recording Times
When using a CF card for recording, you can select one of
three recording modes as appropriate for the desired
• Partially recorded (not yet
finalized) CD-RW discs
recording time and audio quality (
• “Blank disc” refers to an “empty” disc on which nothing
The following table shows the maximum recording times
possible with each recording mode on various capacities
of media.
has been recorded or stored.
■ The Number of Recording Tracks on One
CD-R/RW Disc
Maximum recording time (approx.)
A maximum of 99/98 tracks can be recorded on one
CD-R/RW disc respectively.
Capacity
Recording mode
Long
Standard
3 minutes
6 minutes
12 minutes
24 minutes
49 minutes
98 minutes
WAV
16 MB
32 MB
64 MB
128 MB
256 MB
512 MB
1 GB
6 minutes
1.5 minutes
3 minutes
6 minutes
12 minutes
24 minutes
■ Recorded Songs
12 minutes
24 minutes
49 minutes
98 minutes
When you record on a CD-R/RW disc, a blank space of
two seconds will automatically be added at the end of each
track (song).
■ Finalization (
196 minutes 49 minutes
“Finalization” is a process that can be applied to a CD-R/
RW disc so that it will be playable by a conventional CD
player. Once a CD-R disc or CD-RW disc has been
finalized, it can be played back as a music CD in a CD
player that supports CD-R or CD-RW playback.
196 minutes 392 minutes 98 minutes
392 minutes 784 minutes 196 minutes
2 GB
• The maximum times given above are approximate. The
actual time may be slightly less depending on how tracks
have been edited.
No further songs can be recorded on a CD-R/RW disc that
has been finalized.
• You can view the remaining time in the display.
• If you’re using a CD-RW disc, you can remove the
finalization and add additional material.
• Tracks using differing recording modes may be recorded
on a single CF card.
29
Recording to CF/CD
Recording with the Internal Mics
Here’s how to record a vocal or instrumental performance via
the CD-2’s internal mics (see the illustration below).
2 Press
enough times to get it to
You can record to either a CF card or a CD-R/RW disc.
light in green.
HINT
This means that you’ll be recording the sound
from the internal mics.
• You can check the amount of time that remains on the
media.
• You can increase the amount of free space on a CF card
or CD-RW by deleting unwanted tracks.
3 Adjust the input level of the internal
CF card
mics.
• If you’re recording to a CF card, you can select the
recording mode that’s appropriate for the content you’re
● If Auto Level Control (
input level of the internal mics will be adjusted
automatically. You won’t need to adjust the
internal mic input level.
recording.
When the CD-2 is shipped from the factory, Auto
Level Control is turned “On.”
MEMO
• The sound from the internal mics will not be heard from
the internal speakers. You’ll need to use headphones in
order to audition the sound from the internal mics.
● If Auto Level Control is “Off,” you’ll need to
manually adjust the internal mic input level.
• Since the CD-2 is equipped with highly-sensitive mics,
undesired sounds such as the operating noise of the CD-
R/RW drive* or the sound of buttons being pressed may
be recorded inadvertently.
If you notice such problems, you can try lowering the
Press
.
3
input level of the internal mics.
• Press the button for the media (CF card or CD) on
which you want to record.
*
If you’re recording to a CF card, no CD-R/RW drive
operating noise will be recorded.
The button starts blinking red, and the CD-2 enters
recording-standby mode.
• Depending on where the CD-2 is positioned in relation
to the sound source, the recorded sound may not be
evenly distributed between the left and right speakers. In
such cases, you can adjust the left/right volume balance
of the internal mics and record your performance
Press
.
4
5
again.
• Press the button for the media (CF card or CD) on
which you want to record.
Recording begins.
Power up the CD-2.
1
2
When you’re finished recording, press
.
• Press the button for the media (CF card or CD) on
which you have been recording.
Make preparations for recording.
A new track is created at the end of the CF card or
CD-R/RW disc.
1 Insert a CF card or CD-R/RW disc.
• If the message “Not CD-2 Format” appears,
format the card as described in “Preparing a CF
MEMO
• A CD-R/RW disc must be finalized before it can be
played back by a conventional CD player.
“Make a Disc Playable in a Conventional CD Player”
30
Recording to CF/CD
Recording from a Connected Mic or Instrument
This section explains how to connect mics or instruments to
the CD-2, and record a vocal or instrumental performance.
You can record to either a CF card or a CD-R/RW disc.
2 Press
enough times to get it to
light in orange.
HINT
• The sound from a mic or instrument connected
to the MIC 1/MIC 2/GUITAR/LINE IN jacks
will be selected for recording.
• You can check the amount of time that remains on the
media.
• You can have the CD-2 sound a count-in before
Ensure Accurate Timing”
• If you’re recording only the sound from a
device connected to the LINE IN jacks, press
[MIC SELECT] so it is not lit.
• You can have recording be started automatically as soon
as you begin performing.
instrument connected to the LINE IN jacks”
• You can delete unwanted tracks to increase the free
space on a CF card or CD-RW disc.
3 Adjust the input level.
CF card
• If you’re recording to a CF card, you can select the
recording mode that’s appropriate for the content you’re
recording.
Only if you’re recording from connected mics
4 Specify the panning (stereo position)
of the mics.
• You can use a foot switch to start/pause recording.
In
Step 2 of “Specifying the function of the foot switch” on
mics”
Press
.
4
• Press the button for the media (CF card or CD) on
which you want to record.
The button starts blinking in red, and the CD-2 enters
recording-standby mode.
Connect your mic(s) or instrument(s)
(e.g., guitar or keyboard).
1
Press
.
5
6
• Press the button for the media (CF card or CD) on
which you want to record.
Power up the CD-2.
2
3
Recording begins.
When you’re finished recording, press
.
Make preparations for recording.
• Press the button for the media (CF card or CD) on
which you have been recording.
1 Insert a CF card or CD-R/RW disc.
A new track is created at the end of the CF card or
CD-R/RW disc.
• If the message “Not CD-2 Format” appears,
format the card as described in “Preparing a CF
MEMO
• A CD-R/RW disc must be finalized before it can be
played back by a conventional CD player.
“Make a Disc Playable in a Conventional CD Player”
31
Recording to CF/CD
Layering Your Performance with a Song from a Music CD
(Overdubbing)
While you play back a music CD, you can add your own vocal
or instrumental performance and record the combined result
on a CF card. This process is called “overdubbing.”
Connect your mic(s).
1
The CF card will contain the following recording.
Record your vocal while playing the music CD
Power up the CD-2.
2
Make preparations for recording.
3
Music CD + vocal
The track created by overdubbing
1 Insert a CF card.
• If the message “Not CD-2 Format” appears,
format the card as described in “Preparing a CF
MEMO
• The track created by overdubbing will be at the end of
the CF card.
• The metronome cannot be used while overdubbing a
2 Press
enough times to get it to
performance with a music CD (
light in orange.
• “The sound from the mic connected to the MIC
1/MIC 2 jacks” will be selected for recording.
HINT
• You can check the amount of recording time that
remains on the CF card.
• You can increase the amount of free space on a CF card
3 Adjust the input level.
• You can use the Center Cancel function to create a
karaoke CD by removing a vocal from a CD that
contains a vocal.
4
Set the panning (stereo position) of
the mics.
the Playback”
*
On some CD tracks (songs), this may not produce the
desired result.
mics”
• You can select the recording mode that’s appropriate for
the content you’re recording.
• You can use a foot switch to start/pause recording.
In
Step 2 of “Specifying the function of the foot switch” on
32
Prepare the music CD.
Press
on the CF card side.
4
6
The music CD track you selected in Step 4 begins
playing, and recording on the CF card begins
simultaneously. Record your vocal or instrumental
performance.
1 Insert the music CD.
• If you’re overdubbing with a song from a music CD,
the upper right of the screen will indicate
“CD→CF.”
2 Press
on the CD side.
The CD is selected as the source.
3 Press
or
to select the track
that you want to play back.
When the music CD track ends, recording ends
automatically (the music CD stops playing).
4
Adjust the playback level of the music
CD.
A new track is created at the end of the CF card.
MEMO
• If you decide to stop recording midway through the
track, press
on the CF card side.
If necessary, you can also adjust the input level of
the mic or guitar so that the overall balance is
appropriate (Step 3- 3 ).
HINT
• You can connect an instrument instead of a mic, and
overdub your own instrumental performance along with
the playback from a “minus-one” CD.
Repeatedly press
until “CD →CF”
5
• You can also use the internal mics for recording instead
of connecting a mic.
appears in the display.
Now you are ready for overdubbing.
If you’re recording using the internal mics, you won’t
hear any sound from the internal speakers. You’ll need
to use headphones to monitor your performance.
CD track number
you’re playing back
CF track number
you’re recording
MEMO
•
Canceling overdubbing
To cancel overdubbing, repeatedly press
[OVERDUBBING] until its indicator goes out.
You can also cancel overdubbing by pressing
CF card side.
on the
33
Recording to CF/CD
Layering Your Performance with a Song from a CF Card
(Overdubbing)
While playing back a previously recorded performance from
a CF card, you can layer—or “overdub”—another vocal or
instrumental performance and record the combined result to
a new track.
Connect your mic or guitar.
1
Since you can continue overdubbing parts, you can create a
song by adding elements one at a time. For example, you can
start with drums, then add bass, and then a vocal, and so on.
Power up the CD-2.
2
The CF card will contain the following.
Track
1
1
number
Drums
While playing, record the bass
Make preparations for recording.
3
Track
number
2
1 Insert a CF card.
Drums + Bass
Drums
The track created
by overdubbing
2 Press
enough times to get it to
MEMO
light in orange.
• The new track created by overdubbing is placed at the
• “The sound from the mic or instrument
connected to the MIC 1/MIC 2/GUITAR/
LINE IN jacks” will be selected for recording.
end of the CF card.
HINT
• You can switch the time display to show the remaining
recording time on the CF card.
• If you’re recording only the sound from a
device connected to the LINE IN jacks, press
[MIC SELECT] so it is not lit.
• You can select the recording mode that’s appropriate for
instrument connected to the LINE IN jacks”
the content you’re recording.
• You can increase the free space available on a CF card by
3 Adjust the input level.
• You can have the CD-2 sound a count-in before
Ensure Accurate Timing”
Only if you’re recording from connected mics
4 Set the panning (stereo position) of
the mics.
• You can use a foot switch to start/pause recording.
In Step 2 of “Specifying the function of the foot
switch.
mics”
34
Preparing the CF Card
On the CF card side, press
.
4
6
7
Recording begins. While you listen to the playback of
the track you selected in Step 4, perform your
additional vocal or instrumental part to record it.
1 Press
on the CF card side.
The CF card is selected as the source.
• If you’re overdubbing with a song from a CF card,
the upper right of the screen will indicate
“CF→CF.”
2 Press
or
to select the track
that you want to play back.
3 Adjust the playback level of the CF
card.
When you’re finished recording,
press
on the CF card side.
If necessary, you can also adjust the input level of
the mic or guitar so that the overall balance is
appropriate (Step 3- 3 ).
The newly recorded track is added at the end of the CF
card. Play back the last track (
result of your overdubbing.
Repeatedly press
until “CF →CF”
5
appears in the display.
Now you are ready for overdubbing.
CF track number
CF track number
you’re playing back you’re recording
MEMO
•
Canceling overdubbing
To cancel overdubbing, repeatedly press
[OVERDUBBING] until its indicator goes out.
You can also cancel overdubbing by pressing
CF card side.
on the
35
Recording to CF/CD
Settings for Recording
Preparing a CF Card for Use
(Formatting)
Choosing the CF Card Recording
Mode
When you use a CF card to record, you can choose one of three
recording modes as appropriate for the desired audio quality
and recording time.
When you insert a CF card, the CD-2 determines if it can use
the card in its current state. If the message “Not CD-2 Format”
appears, the CF card will have to be formatted before it can be
used with the CD-2.
MEMO
NOTE
• You can’t change the recording mode while recording;
you must choose the desired recording mode before you
record.
• You are free to select a different recording mode each
time you record. Also, a single CF card can hold and
play back recordings that were made with different
recording modes.
• Never turn off the power or remove the CF card while
formatting is being carried out. Doing so may destroy
the data on the CF card or render the CF card unusable.
• Formatting a CF card erases all data currently residing
on the card.
• The sampling rate is fixed at 44.1 kHz.
• There is no recording mode setting for a CD-R/RW disc.
MEMO
• The included CF card has already been formatted.
• If the CF card has already been formatted on the CD-2,
Press
until “CF Rec Mode” appears
1
2
you don’t need to format it again. Simply continue using
it.
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Insert the CF card into the CF card slot.
1
The message “Not CD-2 Format. Format?” appears.
Turn
to select the desired
recording mode.
Standard: Standard recording.
Normally, you should choose this mode.
Extended recording.
Press
.
2
3
Long:
This recording mode is suitable for
recording lectures or live performances.
The “You’ll Lose Data. Really Sure?” message appears.
WAV:
High-quality recording.
The audio will be recorded as a wave file
(WAV format). Choose this mode if you
will be transferring the audio data to
your computer.
To format the card, press
.
• For the approximate recording times available for
(If you decide to cancel, press
.)
Formatting begins. Once the formatting has been
successfully completed, the following screen appears.
• If desired, a track you recorded in “Standard” or
“Long” mode can be converted to a wave file (WAV
format) after recording.
Press
twice.
3
You’re returned to the previous readout.
36
Selecting the Recording Source
(MIC SELECT)
Adjusting the Input Level
Internal Mic
Select the audio source that you want to record.
If Auto Level Control (
adjust the internal mic input level manually.
Press
enough times to choose the
1
audio source you want to record.
Make sure that [MIC SELECT] is lit green.
CHECK
Each time you press [MIC SELECT], its button will
change color. Press the button until it is lighted in the
appropriate color, the one corresponding to the audio
source you want to record.
MEMO
• If Auto Level Control (
level of the internal mics will be adjusted automatically.
You won’t need to adjust the internal mic input level.
Lit green
Lit orange
Unlit (off)
When the CD-2 is shipped from the factory, Auto Level
Control is turned “On.”
Audio source that will be recorded
• The sound from the internal mics will not be heard from
the internal speakers. You’ll need to use headphones in
order to audition the sound from the internal mics.
The internal mics
Lit green
• Mics connected to the MIC1/MIC2
jacks
Lit orange
• An instrument (guitar or bass)
connected to the GUITAR jack
Press
until “Int MIC Gain” appears in
1
2
The internal mics or a mic or guitar
connected to the MIC1/MIC2/GUITAR
jacks will not be recorded.
Choose the off (unlit) setting if you’re
not recording a mic or guitar.
Unlit (off)
the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
MEMO
• If cables are plugged into both the MIC 1 (XLR-type or
phone-type) and the GUITAR jack, the input from MIC 1
jack will be cancelled.
While listening to the sound, turn
to adjust the input level.
• If you’re recording from the internal mics ([MIC
SELECT] is lit green), the sound of the internal mics will
not be heard from the speakers. You’ll need to use
headphones if you want to audition the sound of the
internal mics.
• You can adjust the input level in a range of 1–50.
POINT
NOTE
For best results, adjust the level so that the level meter
briefly reaches “-3 dB” when you play strongly or
speak loudly.
• You must not connect a mic to both MIC jacks (XLR-type
and phone-type) of the same number. Doing so will
damage the mic and/or the CD-2.
■ Auditioning the sound of an instrument
“-3dB”
connected to the LINE IN jacks
The sound from the LINE IN jacks is always active,
regardless of the [MIC SELECT] setting.
• If you want to record only the sound of an instrument
connected to the LINE IN jacks, turn [MIC SELECT] off
(unlit).
Press
twice.
3
• If you don’t want to record the sound of an instrument
connected to the LINE IN jacks, turn the line input “Off.”
You’re returned to the previous readout.
Sound will no longer be input via the LINE IN jacks.
37
Recording to CF/CD
Settings for Recording (continued)
Adjusting the Input Level (continued)
Temporarily Adjusting the Playback
Level of a Music CD or CF Card
MIC 1/MIC 2/GUITAR/LINE IN Jacks
If you’re playing back a music CD or CF card while recording
an additional vocal or instrument “layered” onto it (
CF card to create the correct balance.
In such cases, you can adjust the playback level of the music
CD or CF card to create the desired balance.
Here’s how to adjust the input level of the input jacks (MIC 1/
MIC 2/GUITAR/LINE IN jacks) to which you’ve connected
mics or instruments.
Make sure that [MIC SELECT] is lit orange.
Press
for the media (CD or CF)
CHECK
*
If you want to record only from a device
connected to the LINE IN jacks, make
sure that [MIC SELECT] is not lighted.
1
2
whose playback level you want to adjust.
Turn
to adjust the playback level.
While you listen to the sound, turn the
appropriate level knob to adjust the input
level.
1
When you turn [DATA], the playback level of the
music CD or CF card is displayed.
The different input jacks are controlled by the
following level knobs.
“CF Mix Level”
when using a CF card
Jack name
Level knob
• You can adjust the level in a range of -50– +25.
• A setting of “0” is the original playback level.
MIC 1
GUITAR
POINT
* Front panel
* Front panel
For best results, adjust the level so that the level meter
briefly reaches “-3 dB” when the sound from the music
CD or CF card is mixed with the sound of the mic or
instrument.
MIC 2
LINE IN
“-3dB”
MIN
MAX * Rear panel
POINT
For best results, adjust the level so that the level meter
briefly reaches “-3 dB” when you play strongly or
speak loudly.
When you’ve finished adjusting the
3
playback level, press
.
• Press the button for the media (CF card or CD)
you’re playing.
“-3dB”
• If you do not operate the [DATA] dial for five
seconds, you will be automatically returned to the
previous readout.
MEMO
MEMO
•
Adjust [OUTPUT LEVEL] so that you can comfortably
listen to the connected instrument or mic. Adjusting this
volume will not affect the sound (input level) that’s
• Noise may occur if you adjust the playback level during
playback. This is normal and does not indicate a
malfunction.
• The playback level setting you adjust here is temporary,
and will be cleared when you turn off the power. It will
be returned the original playback level the next time you
turn on the power. If you want to keep the playback
being recorded.
level setting, make settings as described in
38
When Recording from
Connected Mics (Pan Setting)
Adjusting the Left/Right Volume
Balance of the Internal Mics
“Pan” refers to the left/right position of the sound. On the
CD-2, the pan of the mics connected to the MIC1 and MIC2
jacks can be set to left, right, or center.
When you record via the internal mics, the left and right
channels of the recorded sound may be perceived as not being
balanced, depending on the location in which the CD-2 is
placed.
When using two mics to record a lecture or band performance,
you can set the pan to left and right so that the natural
spaciousness of the sound is captured (i.e., stereo recording).
For example, if the CD-2 has been placed at an angle relative
to the audio source you’re recording, the sound from the mic
that is closer to the audio source will sound louder.
You can adjust the left/right volume balance of the internal
mics as appropriate for the location in which the CD-2 is
placed.
Press
until “Ext MIC1/2 Pan” appears
1
2
in the display, and then press
.
Make sure that [MIC SELECT] is lit green.
• You can also select this item by turning [DATA].
The following screen appears.
CHECK
Press
until “Int MIC Bal” appears in
1
2
the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to select how MIC 1 and MIC 2
are to be panned.
MIC 1
Left
MIC 2
Right
Center
Left
L/R
C/C
R/L
L/C
R/C
C/L
C/R
Center
Right
Left
While making sound, adjust the volume
balance of the L and R channels.
Center
Center
Left
Right
Center
Center
Adjust the volume balance so that the L and R meters
show approximately the same level.
Right
• Normally, you should choose “C/C” when
recording a solo performer. You should also choose
“C/C” if you’re recording from a single mic.
Choose “L/R” when recording a band
performance or a lecture.
• You can adjust the balance from L50–R50. The
center position (C) indicates that both microphones
will pick up sound at equal level.
When set to L50, no sound will be picked up by the
R channel mic. When set to R50, no sound will be
picked up by the L channel mic.
Press
twice.
3
You’re returned to the previous readout.
Press
twice.
3
You’re returned to the previous readout.
39
Playback
Playing Back a CD
Playing Back at a Slower Speed
(Slow Playback)
Insert the CD.
1
2
You can play back the CD slowly without changing the pitch
of the sound. This is convenient when you want to play your
instrument along with a “minus-one” CD, or to learn phrases
by ear.
On the CD side, press
.
The CD is selected as the audio source, and playback
begins.
MEMO
• Slow Playback is a CD-only function. You can’t use it
with a CF card.
Elapsed playback time
HINT
Currently playing track number
• When you’re practicing difficult phrases, you may find it
convenient to use the A-B Repeat function (
in conjunction with the Slow Playback function.
MEMO
• You can switch the time display to show the remaining
playback time.
Press
.
1
Turn
to adjust the volume.
The CD speed control screen appears.
3
To do this
Perform this action
Stop playback
Press the CD
.
Turn
to adjust the CD playback
speed.
If you press this button while
stopped, you will return to the first
track.
2
3
• You can adjust the speed in a range of -50 (half
speed) through 0 (normal speed).
Pause playback
Press the CD
.
Press it once again to resume
playback from the point at which
you paused.
Press
.
Go to the
beginning
of a track (Skip)
Press
.
Each time you press this button, you
go back by one track. If you press
this button during playback, you
will return to the beginning of the
track that was playing.
You’re returned to the previous readout.
Thereafter, the CD will play back at the speed you
specified in Step 2.
MEMO
Press
.
• For some tracks (songs), decreasing the speed might
Each time you press this button, you
advance to the next track.
make the notes more difficult to distinguish.
•
Icon indication
While stopped, press and hold
Skip between
songs at
high-speed
The speed icon is displayed if you’ve changed the
playback speed.
or
.
During playback, press and hold.
Rewind/
fast-forward
(Search)
The speed icon disappears if you set the Speed to “0” in
Step 2.
: Rewind./
: Fast-forward.
Speed icon
While paused, press and hold
High-speed rewind/
fast-forward
or
.
40
Making Fine Adjustments to the Playback Pitch (Pitch)
You can make fine adjustments (of less than a semitone) to the
pitch of the CD playback.
Press
.
3
Sometimes when you are practicing your instrument along
with a CD, you may have difficulty because the CD playback
is pitched slightly different than your instrument. In such
cases, you can adjust the CD playback pitch to match your
instrument.
You’re returned to the previous readout.
Thereafter, the CD will play back at the pitch you
specified in Step 2.
Even if you’re using an instrument that is not easily tuned,
such as an acoustic piano, you can adjust the pitch of the CD
so that it matches your instrument.
MEMO
Icon indication
•
The Pitch icon is displayed if you’ve changed the Pitch
setting.
MEMO
The Pitch icon disappears if you set the Pitch to “0” in
Step 2.
• Pitch adjustment is a CD-only function. You can’t use it
with a CF card.
Pitch icon
Press
display.
until “Pitch” appears in the
1
2
Turn
to adjust the CD playback
pitch.
• The range of adjustment available for the pitch is
-50 cents through +50 cents.
• A setting of “0” produces the original pitch.
HINT
• If you have a CD that was recorded at a reference pitch
of A=440 Hz, and you want to play it back at a reference
pitch of A=442 Hz, you would set Pitch to “+8.” Refer to
the table below.
Pitch setting
Reference pitch (Hz) after adjustment
-8
-4
0
438
439
440
441
442
+4
+8
MEMO
• One cent is 1/100th of a semitone; i.e., a semitone is 100
cents.
41
Playback
Playing Back a CD (continued)
Changing the Key of the
Playback (Key)
Removing the Vocal or Lead Guitar
from the Playback (Center Cancel)
You can raise or lower the key of the CD playback.
This can be useful in situations like the following.
You can remove the main vocal or lead guitar from the
playback of a CD, or make it less audible.
This is useful when you want to use a favorite CD to practice
soloing or to enjoy karaoke.
• You want to practice flute along with an accompaniment
CD that was created for alto sax.
• You want to sing along with a karaoke CD at a key that’s
easier for you to sing.
MEMO
• Center Cancel is a CD-only function. You can’t use it
with a CF card.
MEMO
• Key change is a CD-only function. You can’t use it with a
CF card.
Press
.
1
2
The Center Cancel function is turned on, and the “
icon appears.
”
Press
display.
until “Key” appears in the
1
2
Center Cancel icon
From this point on, the sound of the main vocal or lead
guitar is eliminated from the playback.
• Depending on the track (song) you’re playing back,
you may not obtain the desired result.
Turn
to adjust the CD playback
key.
• You can adjust the key in semitone steps over a
range of -6 through +5.
When you want to return to normal CD
playback, press
again.
“+” (positive): Raise the key
“-” (negative): Lower the key
The Center Cancel function is turned off, and the “
icon disappears.
”
• “0” returns to the original key.
Press
.
3
You’re returned to the previous readout.
Thereafter, the CD will play back at the key you
specified in Step 2.
MEMO
•
Icon indication
The Key icon is displayed if you’ve changed the Key
setting.
The Key icon disappears if you set the Key to “0” in
Step 2.
Key icon
42
Repeatedly Playing Tracks
(1 Track/All Repeat)
Repeatedly Playing a Section
(A-B Repeat)
You can have a favorite track (or all tracks) play back
repeatedly.
You can have a specified section play back repeatedly.
Repeatedly listening to a section of a song is convenient when
you’re practicing your instrument along with the song, or
learning the song by ear.
Press
to select Repeat mode.
HINT
1
• If you’re learning a difficult phrase by ear, you may find
Each time you press the button, the Repeat mode
indication will change as follows.
it convenient to use the A-B Repeat function together
with the Slow Play function (
While a CD is playing, press
at the
1
point where you want Repeat Play to
start.
No indication
(All repeat)
(Repeat off)
(1 track repeat)
The starting point (A) of A-B Repeat playback is
registered, and the point A icon blinks.
1 track
repeat:
The currently playing track, or any
track you play subsequently, will play
back repeatedly.
Point A icon (blinking)
All repeat: All tracks will play repeatedly. If you
select this during playback, all tracks
will play repeatedly, starting with the
currently playing track.
Press A-B at the point where you want
A-B Repeat to end.
2
The end point (B) of A-B Repeat playback is registered,
and the A-B region will play back repeatedly.
Repeat off: The Repeat Play function is cancelled.
MEMO
Icon indication
MEMO
To cancel Repeat Play
•
•
The A-B Repeat icon is displayed during A-B Repeat
playback.
To cancel Repeat Play, press [1/ALL] several times until
the
If you open the CD disc tray or cycle the power to the
CD-2, the icon disappears and the Repeat Play
function is cancelled.
/
icon disappears.
/
A-B Repeat icon
•
Canceling A-B Repeat
During A-B Repeat playback, press [A-B]; the A-B
Repeat function is cancelled, and you are returned to
normal playback.
If you press
on the CD side, A-B Repeat will be
cancelled, and the CD playback will stop.
43
Playback
Playing Back a CF Card
Repeatedly Playing Tracks
Insert the CF card.
1
2
(1 Track/All Repeat)
You can have a favorite track (or all tracks) play back
repeatedly.
On the CF card side, press
.
The CF card is selected as the source, and playback
begins.
Press
to select Repeat mode.
1
Each time you press the button, the Repeat mode
indication will change as follows.
Elapsed playback time
Currently playing track number
MEMO
• You can switch the time display to show the remaining
No indication
(Repeat off)
playback time.
to adjust the volume.
Perform this action
(All repeat)
(1 track repeat)
Turn
3
1 track
repeat:
The currently playing track, or any
track you play subsequently, will play
back repeatedly.
To do this
Stop playback
All repeat: All tracks will play repeatedly. If you
select this during playback, all tracks
will play repeatedly, starting with the
currently playing track.
Press the CF
.
If you press this button while
stopped, you will return to the first
track.
Repeat off: The Repeat Play function is cancelled.
Pause playback
Press the CF
.
Press it once again to resume
playback from the point at which
you paused.
MEMO
To cancel Repeat Play
•
Go to the
beginning
of a track (Skip)
To cancel Repeat Play, press [1/ALL] several times until
Press
.
the
If you cycle the power to the CD-2, the
disappears and the Repeat Play function is cancelled.
/
icon disappears.
Each time you press this button, you
go back by one track. If you press
this button during playback, you
will return to the beginning of the
track that was playing.
/
icon
Press
.
Each time you press this button, you
advance to the next track.
While stopped, press and hold
Skip between
songs at
high-speed
or
.
During playback, press and hold.
Rewind/
fast-forward
(Search)
: Rewind./
: Fast-forward.
While paused, press and hold
High-speed rewind/
fast-forward
or
.
44
Repeatedly Playing a Section
(A-B Repeat)
You can also play back wave files (WAV
format) that have been written to the CF
card using a computer
You can have a specified section play back repeatedly.
Repeatedly listening to a section of a song is convenient when
you’re practicing your instrument along with the song, or
learning the song by ear.
Wave files (WAV format) written to the CF card using a
computer can also be played back.
Playback
Computer
While a CF card is playing, press
at
1
the point where you want Repeat Play to
start.
CD-2
The starting point (A) of A-B Repeat playback is
registered, and the point A icon blinks.
Wave files
(WAV format)
Point A icon (blinking)
■ Wave files (WAV format) that can be played
The CD-2 can play wave files that meet the following
conditions.
Press A-B at the point where you want
A-B Repeat to end.
2
16-bit linear/44.1 kHz/stereo/
filename extension “.WAV” (.wav)/
Four seconds or longer (approximately 690 KB or
more)
The end point (B) of A-B Repeat playback is registered,
and the A-B region will play back repeatedly.
MEMO
Icon indication
■ Write-destination directory
•
Write the wave file to the “root directory” of the CF
card.
The A-B Repeat icon is displayed during A-B Repeat
playback.
NOTE
• We cannot guarantee that the CD-2 will operate
correctly if you manipulate any directories or files
that are not related to wave files.
A-B Repeat icon
•
Canceling A-B Repeat
■ CF cards that contain recorded data
During A-B Repeat playback, press [A-B]; the A-B
Repeat function is cancelled, and you are returned to
normal playback.
If you write wave files to a CF card that is being used
by the CD-2 (i.e., a CF card that already contains
recorded data), the files will be added following the
last track in alphabetical order of their title.
If you press
cancelled, and the CF card playback will stop.
on the CF side, A-B Repeat will be
* File names become track titles.
45
Creating a Music CD
Creating a Music CD from a CF Card
Here’s how you can create a music CD by writing tracks from
a CF card to a CD-R/RW disc.
Turn
to select the track that you
want to write.
4
NOTE
• We cannot guarantee that music CDs created by the
CD-2 will play back on all CD players. Depending on its
support for CD-R/RW discs, your CD player may be
unable to play them correctly.
• You can also press
or
to select the track.
CF card track number and title
MEMO
• Two seconds of silence are automatically inserted
between tracks on the CD-R/RW disc when you create a
music CD.
CD track number
• If you want to audition the selected track, press
on the CF card side. To stop playback, press
the CF card side.
HINT
on
• By using a mastering effect (
eliminate inconsistencies in the volume across the
various frequency ranges, making the CD more
professional sounding.
Press
.
If you want to use a mastering effect to create a music
CD, choose the type of mastering effect before you
5
6
The track you selected in Step 4 is selected as the track
to be written.
continue.
Sounding CD”
If there are other CF card tracks that you would like to
write to the CD, repeat Steps 4–5.
Insert the CF card.
1
2
When you’ve selected all of the tracks
that you want to write to the CD, press
.
Press
.
The message “CD WRITE. Are You Sure?” appears.
The “Insert Disc” message appears and the disc tray
opens.
To write the tracks to disc, press
.
7
(If you decide to cancel, press
The FINALIZE screen appears.
.)
Insert a blank or appendable CD-R/RW
disc.
3
When the CD-2 recognizes the CD-R/RW disc, the
following screen appears.
46
If “No” is selected in Step 8
1 Press
Choose whether you want to finalize the
disc.
8
.
Finalization is a process that makes the newly written
CD-R/RW disc playable in a conventional CD player.
(If you decide to cancel writing, press
.)
• The CD-2 is able to play back unfinalized CD-R/
RW discs.
Writing to the CD-R/RW disc begins.
When writing has been successfully completed, the
CD-R/RW disc is ejected and the message “Write
Completed. Another Disc?” appears.
When writing is finished, the disc will be
Yes
finalized to complete the music CD.
No further data can be written to a CD-R/
RW disc that has been finalized, even if
space remains on the disc.
However, if you’re using a CD-RW disc,
you can remove the finalization and add
additional material.
If you want to write the same tracks to
10
another CD-R/RW disc, press
.
The disc will not be finalized when writing
is finished.
No
The “Insert Disc” message appears.
After the tracks have been written, you
will still be able to add more tracks if space
remains on the disc.
You can also perform the finalization step
later to complete the music CD.
Insert another blank or appendable CD-R/RW disc,
close the disc tray, and the “CD WRITE. Are You
Sure?” message appears.
Conventional CD Player”
Return to Step 7 and continue the procedure.
If “Yes” is selected in Step 8
If you are finished with writing, press
.
9
You’re returned to the screen from which you started.
1 Press
.
(If you decide to cancel writing, press
.)
Play back the CD-R/RW disc you just wrote (
The message “FINALIZE. Are You Sure?” appears.
2 To write the tracks to disc, press
.
(If you want to return to Step 8, press
.)
Writing to the CD-R/RW disc begins. After the tracks
are written, the disc will be finalized.
When writing has been successfully completed, the
CD-R/RW disc is ejected and the message “Write
Completed. Another Disc?” appears.
● What to do if a track is larger than the capacity
of a CD-R/RW disc
● Creating a music CD using tracks from more
than one CF card
See the next page.
47
Creating a Music CD
Creating a Music CD from a CF Card (continued)
What to do if a track is larger than the capacity of a CD-R/RW disc
Even if a track is larger than can be written to a single CD-R/RW
disc, it can automatically be divided across multiple CD-R/RW
discs for writing.
First CD-R/RW disc
Second CD-R/RW disc
If you want to automatically divide and write a large track,
proceed as follows.
Automatically
divided
to be written. A track can be written across multiple discs only
if the first track specified for writing is larger than can be
written to a single CD-R/RW disc.
Track
• If you specify a large-size track, you will not be able to specify
more than one track for writing.
Portion that does not fit
on first CD-R/RW disc
● After the first CD-R/RW disc has been ejected, the message
“Insert Disc” will appear. Insert another CD-R/RW disc.
When the disc is detected, writing will begin automatically.
Continue inserting additional CD-R/RW discs as directed by the messages that appear.
When all the data has been written, the message “Write Completed. Another Disc?” will appear. Continue with the
• CD-R/RW discs that have no more space on them after the track has been written will be finalized automatically. For
example, if a track is divided across two discs, as in the example shown in the illustration at the upper right, the first
CD-R/RW disc will be finalized automatically.
Creating a music CD using tracks from more than one CF card
If the CD-R/RW disc has not been finalized, you can add tracks from another CF card. If you want to create a music CD
using tracks from more than one CF card, simply keep adding tracks to a CD-R/RW disc and finalize the disc when you’re
finished.
Write to
CD TRACK 01
Write to
CD TRACK 02
Completed music CD!
Finalize
TRACK03
TRACK05
CF card
CF card
48
Creating a Professional-Sounding CD (Mastering Effects)
When creating a music CD from tracks on a CF card, you can
apply a mastering effect to eliminate inconsistencies in the
volume across the various frequency ranges, making the
music CD more professional sounding.
■ Mastering Effect Patch List
Patch Name
Mixdown
Function
Basic mixdown for CD.
Final mix of live recording.
Mix for video or radio narration.
You can choose one of 25 different Mastering Effect patches.
Choose the patch that is most suitable for the music CD you
want to create.
Live Mixing
Narration
Jam Session
Use for recording a practice or jam
session in loud rehearsal room.
MEMO
OutDoors
Controls background noise of
recordings made outdoors.
• You can’t use a Mastering Effect at the same time as the
other effects (
Rock Band
Low Boost
Use for pop or rock bands.
Enhances the low frequency range of
drums and bass.
Press
.
Brighten
Piano
Adds crispness and sizzle to the overall
mix.
1
2
The Mastering Effect screen appears.
Use to control the dynamic range of
acoustic pianos.
Choir
Use for vocal ensembles.
Use for brass ensembles.
Use for woodwind ensembles.
Brass
• If an effect (
MASTERING? FX will be Off” message appears.
Woodwind
Orchestra
Press the [ENTER] button to turn off the effect; the
mastering patch screen appears.
Level control and air for live
recordings of bands or orchestras.
Acoustic
Adds clarity and warmth to strummed
or plucked acoustic instruments.
Turn
to select a Mastering Effect
patch.
Mix CD
Use when compiling tracks from
different sources for uniform levels.
CMP+FAT EQ
Maximized sound level and tonal
character suitable for dance music.
• For a list of patches, refer to the table on the right.
LO&SLOW FLNG Slow modulation effect.
• If you choose a selection other than “Off,” the
Mastering Effects will be on, and [MASTERING]
will light.
ST CHORUS
PS:DETUNE
ST DOUBLER
Deep and spacious sound produced by
a chorus effect.
Pitch-shifted sound added to create
depth.
• After selecting a Mastering Effect patch, you can
play back the CF card to audition the sound of the
chosen patch.
Doubling applied to produce a
spacious sound.
Mastering Effects applied.
CHORUS+DELAY Chorus and delay combined to
enhance the spatial spread.
1920’s RADIO
1960’s RADIO
VINTAGE 45’s
CLASSIC LP
Simulates the sound of an antique
radio that’s not tuned correctly.
MEMO
• If you’re using Mastering Effects, it will take longer to
write the tracks.
Simulates the sound of a noisy old
radio.
The writing time will be approximately 1.5 times the
length of the tracks.
Simulates the sound of a 45 RPM single
played on an antique phonograph.
• When the tracks have been written, Mastering Effects
will automatically be turned “Off.”
Simulates the sound of an LP played on
a turntable.
• If you don’t want to use Mastering Effects, choose “Off”
in Step 2. Alternatively, press the [MASTERING] button
once again.When MASTERING Effects are “Off,”
[MASTERING] is unlit.
49
Creating a Music CD
Make a Disc Playable in a Conventional CD Player (Finalize)
In order for a CD-R/RW disc you’ve recorded on the CD-2 to
be playable in a conventional CD player, you must “finalize”
the disc.
Insert the CD-R/RW disc that you want to
finalize.
1
A finalized CD-R disc or CD-RW disc can be played back as a
music CD in a CD player that supports CD-R or CD-RW
playback, respectively.
CD player that supports
The CD-2
Press
.
CD-R (CD-RW) playback
2
3
Finalized
disc
Playable
Playable
Playable
The “Are You Sure?” message appears.
Unfinalized
disc
Not playable
NOTE
• We cannot guarantee that music CDs created by the
CD-2 will play back on all CD players. Depending on its
degree of support for CD-R/RW discs, your CD player
may be unable to play them correctly.
To finalize the disc, press
.
(If you decide to cancel, press
.)
The disc is finalized. During this process, a timer is
displayed, counting-down the time until finalization is
completed.
MEMO
• No more data can be written/recorded to a CD-R/RW
disc that has been finalized, even though there may be
space remaining on the disc.
However, in the case of a CD-RW disc, you can remove
the finalization and add/record additional material.
Counting-down
When finalization is completed, the CD-R/RW disc is
ejected. Your music CD is now ready.
50
Advanced Operation
This section explains the more advanced functions of the CD-2.
■ Using the Metronome ........................................................................... 52
Other Recording
Methods
Erasing All Tracks................................................................................................ 58
More Functions
Formatting a CF Card.......................................................................................... 63
Erasing the Last Track......................................................................................... 64
Erasing All Tracks................................................................................................ 64
Changing the Tuner’s Reference Pitch................................................................ 67
Displaying the Remaining Time........................................................................... 75
Switching the Line Input On/Off........................................................................... 78
Viewing the Track Titles on a CF Card................................................................ 78
51
Other Recording Methods
Using the Metronome
You can sound a metronome—a convenient feature for
practicing your instrument.
Setting the tempo.
3
MEMO
1 Press
until “Tempo” appears in
• The metronome cannot be used while overdubbing a
the display, and then press
.
performance with a music CD (
• You can also select this item by turning [DATA].
The following screen appears.
Press
.
1
2
The metronome is turned on, and the [METRONOME]
button blinks.
2 Turn
to set the metronome’s
tempo.
Setting the sound.
1 Press
.
• You can adjust the metronome’s tempo in a
range of =20–250 (the number of quarter notes
in one minute).
“[METRONOME] Sound” appears in the display.
3 Press
.
• If [MENU] is pressed while the metronome is
turned on, the screen to select the metronome
sound (“Sound”) will appear instead.
You’re returned to the previous readout.
Specifying which beats are emphasized.
2 Press
.
4
The following screen appears.
1
Press
until “Beat” appears in the
display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
3 Turn
to select the metronome
sound.
Click: An electronic tone will be heard.
Bell: A bell will be heard.
Off: The metronome sound is turned off (the
[METRONOME] button will continue to
blink).
4 Press
.
You’re returned to the previous readout.
52
Sounding a Count-In to Ensure
Accurate Timing (Count-in)
2 Turn
to choose which
metronome beats are
emphasized.
You can sound a count-in before recording begins.
This provides a timing reference for your recorded
performance.
• A quarter-note will be counted as one beat.
0:
1:
2:
3:
4:
5:
6:
7:
No beats are emphasized.
Every beat is emphasized.
MEMO
Every second beat is emphasized.
Every third beat is emphasized.
Every fourth beat is emphasized.
Every fifth beat is emphasized.
Every sixth beat is emphasized.
Every seventh beat is emphasized.
• If you’re recording from the internal mics (when [MIC
SELECT] is lit green:
be heard from the internal speakers. You’ll need to use
headphones in order to hear the count-in.
: Each beat is divided into a triplet, and an
emphasized beat will sound at the beginning
of each triplet.
Following Step 5 on left column...
6
Press
until “Count-in (Beat)” appears
: Each beat is divided into sixteenth notes, and
an emphasized beat will sound on the
sixteenth note at the beginning of each beat.
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Press
twice.
5
6
You’re returned to the previous readout.
To stop the metronome, press
again.
Turn
to specify the number of
beats that will be counted
before recording begins.
7
8
The metronome is turned off, and the [METRONOME]
button becomes unlit.
Off:
No count-in will sound.
1–16:
The specified number of count-in beats will
sound.
MEMO
Press
twice.
•
How the [METRONOME] button indicates the tempo
and emphasized beats
You’re returned to the previous readout.
When the metronome is on, the [METRONOME] button
will blink in time with the beat. Red indicates the
emphasized beats, and green indicates the un-
emphasized beats.
• If you want to disable the count-in, choose “Off” in
Step 7.
■ When recording with the metronome
If you’re recording from the internal mics (when [MIC
heard from the internal speakers in recording-standby
mode or during recording. You’ll need to use
headphones in order to hear the metronome.
53
Other Recording Methods
Automatically Starting Recording When Sound Begins
You can have the CD-2 start recording when it detects sound
that is louder than a specified level.
Press
twice.
4
If you start recording the usual way, by pressing a button, a
length of silence will be recorded until you begin playing your
instrument. However, if you use the CD-2’s Auto Rec Start
function, recording will start automatically in response to
your voice or instrument, letting you record without creating
a length of silence at the beginning of the track.
You’re returned to the previous readout.
This completes preparations for automatically starting
recording.
Press
.
HINT
5
6
• If you record on a CF card, you can delete unwanted
silence at the beginning of the track after you’re finished
recording (
• Press the button that controls the media (CF card or
CD) to which you’re recording.
MEMO
Press
.
• The Auto Rec Start function will not operate if you’ve
enabled a count-in (
count-in “Off.”
• Press the button that controls the media (CF card or
CD) to which you’re recording.
The message “Waiting Signal..” appears, and the CD-2
enters recording-standby mode.
Make preparations for recording.
1
2
• If you’re recording with the internal mics
Begin playing your instrument.
7
8
• If you’re recording from a connected mic or
When the CD-2 detects sound at a level higher than the
level you specified in Step 3, recording will start
automatically.
instrument
Press
until “Auto Rec Start” appears
in the display, and then press
.
When you’re finished recording,
• You can also select this item by turning [DATA].
The following screen appears.
press
.
• Press the button that controls the media (CF card or
CD) to which you’re recording.
A new track is created at the end of the CF card or
CD-R/RW disc.
Turn
to specify the level at which
recording is to start
automatically.
MEMO
• You can press
3
to pause recording.
Recording will begin automatically the next time the
CD-2 detects sound at a level higher than the level you
specified in Step 3.
Off:
Recording will be started manually.
-48 dB –
-6 dB:
This is the minimum level at which
recording will start. For example if you
choose “-6 dB,” recording will start as
soon as the CD-2 detects any sound
louder than -6 dB.
If you pause recording, a new track will be created at the
point you resume recording.
54
Other Recording Methods
Assigning Tracks Numbers While You Record
You can assign a track number while recording, so that
Using [MARKER] to assign track
subsequently recorded material will be on a new track.
numbers
MEMO
If several songs are being recorded in succession, such as
during a live performance, you can assign a track number to
• You can’t delete a track number once it’s been assigned.
each song while you continue recording.
• You can assign track numbers only during recording.
• The track numbers can be assigned no closer than four
seconds apart. You can’t assign a new track number less
than four seconds after assigning the previous track
number.
At the point where you want to assign a
track number during recording, press
1
.
• You can assign up to 99 track numbers (99 tracks) in one
CF card or CD-R disc. In case of a CD-RW disc, you can
assign up to 98 track numbers (98 tracks).
• Press the button that controls the media (CF card or
CD) to which you’re recording.
The track number is incremented, and the material that
follows will be recorded as on that track.
● When you assign track numbers to a CD-R/RW disc
• When you assign a track number, two seconds of silence
is automatically inserted in front of the new track
number.
HINT
• You can also use a foot switch to assign track numbers.
foot switch at the appropriate moment during recording.
Track number Track number
Performance
A
B
C
Track number
B
Track number
C
CD-R/RW
Disc
A
Silence (two seconds)
• You can’t assign another track number while the
following message is displayed. However, recording will
continue.
This message indicates that the track number is being
written to the CD-R/RW disc.
HINT
• Tracks recorded on a CF card can be split afterward as
desired.
55
Other Recording Methods
Assigning Tracks Numbers While You Record (continued)
Assigning Track Numbers at Specified Intervals
When making a long recording such as a lecture, you can
automatically assign track numbers at fixed time intervals to
divide the recording into tracks. If you’ve assigned track
numbers, it will be easier to find a desired location in the
recording.
Turn
to specify the time interval
at which track numbers are
to be assigned.
5
• You can specify a time interval of 5 min–15 min
(minutes).
Press
until “Auto Marker” appears in
1
2
the display, and then press
.
Press
twice.
6
• You can also select this item by turning [DATA].
The following screen appears.
You’re returned to the previous readout.
Subsequently, when you begin recording, track
numbers will automatically be assigned at every time
interval you’ve specified in Step 3.
• To defeat this setting, choose “Off” in Step 2.
Turn
to select “Time.”
Off:
Track numbers will be assigned at the
points where you press
recording.
while
Time:
Level:
During recording, track numbers will be
assigned at every specified time interval.
During recording, track numbers will be
assigned when the sound drops below a
specified level.
Press
.
3
4
You’re returned to the previous readout.
Press
until “Auto Marker Time” appears
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
56
Assigning Track Numbers When Silence is Detected
You can have track numbers automatically assigned
whenever the CD-2 detects a region of silence (longer than one
second) during recording.
Press
twice.
6
You’re returned to the previous readout.
Subsequently, when you begin recording, the CD-2
will automatically assign a track number when it
detects a period of silence; i.e., a period with a level
that is below the level you specified in Step 3, and that
is at least one second in length.
Press
until “Auto Marker” appears in
1
2
the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
• To defeat this setting, choose “Off” in Step 2.
Turn
to select “Level.”
Off:
Track numbers will be assigned at the
points where you press
recording.
while
Time:
Level:
During recording, track numbers will be
assigned at every specified time interval.
During recording, track numbers will be
assigned when the sound drops below a
specified level.
Press
.
3
4
You’re returned to the previous readout.
Press
until “Auto Marker Lvl” appears
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to specify the level that will
be considered as silence.
5
• You can specify the level in a range of -60 dB– -30
dB.
57
More Functions
Editing a CF Card
Eight editing operations such as Delete or Rename are
provided so songs recorded on a CF card can be edited.
Erasing All Tracks
Insert the CF card that you want
to edit.
Preparations
common to all
CF card editing
operations
1
2
The contents of the CF card will change as follows.
1
2
3
4
Track number
Press the CF card
button to
A
B
C
D
select the CF card as the source.
Delete
NOTE
• You can’t recover a track that you’ve erased. Use caution
before erasing a track.
Blank CF card
Erasing a Track
Press
until “ERASE ALL TRACKS”
1
2
appears in the display.
The contents of the CF card will change as follows.
1
2
3
4
Track number
A
B
C
D
Delete
Press
.
1
2
3
Track number
A
C
D
Blank
The “Are You Sure?” message appears.
Use
or
to select the track you
1
2
want to erase.
Press
.
3
4
The “Really Sure?” message appears.
Press
until “ERASE 1 TRACK”
appears in the display.
To erase all tracks, press
.
Press
.
(If you decide to cancel, press
.)
3
The “Are You Sure?” message appears.
All tracks will be erased, and then you’re returned to
the original readout.
Number of the track
you’re erasing
To erase the track, press
.
4
(If you decide to cancel, press
.)
The track will be erased, and then you’re returned to
the original readout.
58
Assigning a Title to a Track
You can assign a title of up to 250 characters to each track on
a CF card.
■ Entering characters
Characters are entered at the location of the cursor. Move
the cursor and enter the desired characters.
MEMO
To move
the cursor
• Track titles such as “SNG01_00 ➔ SNG02_00 ➔...
Press
or
SNG99_00” are automatically assigned to each track.
The cursor will move backward or
forward.
Track number assigned
when recording.
If there are two or more tracks with
the same title, a two-digit number
is appended to distinguish them.
To choose
a character
Turn
•
Track title display
You can show the track titles in the screen. If you’ve
switched the title display setting “On,” the title will
appear on screen when you switch tracks. Few seconds
To insert a
space
Press
A space (blank) is inserted at the cursor.
Choose the desired character.
later, the screen returns to the time display.
To delete a
character
Press
The character at the cursor is deleted.
Subsequent characters will move forward.
Use
or
to select the track to which
1
2
you want to assign a title.
• You can enter the following characters.
Press
until “RENAME” appears in the
display.
As you turn [DATA] clockwise, the characters will
appear in the order of A ➔ B ➔... Z ➔ [ ➔...
Turning [DATA] counterclockwise will cause the
characters to appear in the opposite order.
*
A blank space or a “.” (period) cannot be used as the
first character of a title. If you try to do so, the CD-2
will delete the first character automatically and use
the subsequent characters for the track title.
Press
.
3
The title entry screen appears.
■ If you rename the file on your computer
Number of the track you’re editing
The tracks are stored in the root directory of the CF card.
The files with an extension of “.WAV” and “.DAT” are
the track files.
Track title
The CD-2 uses the filename as the track name. You can
change the title by renaming the file. This will change the
order of the tracks on the CF card. Tracks you rename
will move to a location following the last track.
Cursor (blinking)
Enter the title. See “Entering characters”
in the next column.
NOTE
4
5
•
•
You must not change the filename extension of
“.WAV” or “.DAT”.
We cannot guarantee that the CD-2 will operate
correctly if you manipulate any directories or files
with extensions other than “.WAV” or “.DAT”.
To confirm the title you’ve entered,
press
.
• Don’t use double-byte characters (e.g., Japanese) or “~”
(tilde) in the filename; the CD-2 is unable to recognize
them.
(If you decide to cancel, press
.)
The title you specified is assigned to the track, and then
you’re returned to the original readout.
• The filename must be 250 characters or fewer (not
including the filename extension).
59
More Functions
Editing a CF Card (continued)
Insert the CF card that you want
to edit.
1
2
Preparations
common to all
CF card editing
operations
Trimming Silence from the Beginning of a Track
Press the CF card
button to
select the CF card as the source.
Use
or
to select the track you
1
2
want to edit.
Trimming Silent Regions at the
Beginning and End of a Track
(Trim In/Out)
Press
until “TRIM IN” appears in the
display.
When recording an instrumental or vocal performance, you
might start recording somewhat earlier than the actual
beginning of the performance and stop recording somewhat
later than the actual end, so as not to lose any of the
performance.
In such cases, there may be an unwanted silence at the
beginning or end of the track.
Press
.
The CD-2 lets you trim such silences from the beginning or
end of the track, so that the sound will begin the moment you
start playing the track.
3
The trim in editing screen appears.
MEMO
• If the CF card does not have enough remaining free
space, you won’t be able to execute the Trim In/Out
operation.
Number of the track you’re editing
Start Point and End Point
On the CF card side, press
.
4
5
If you want to trim silent regions from the beginning or end of
a track, you must first specify the desired Start Point and End
Point. The silent regions will be trimmed as shown below,
according to the Start Point and End Point you specify.
The track will begin playing.
At the desired Start Point, press
the CF card side.
on
• Start Point: The location at which the sound begins.
• End Point: The location at which the sound ends.
Four seconds of sound preceding the Start Point will
play repeatedly.
Beginning of the track
End of the track
Delete
Delete
Plays repeatedly
Four seconds
Silence
Silence
Start Point
End Point
Start Point
Beginning of the track
End of the track
Turn
to precisely adjust the Start
Point.
6
Start Point
End Point
• Turn [DATA] clockwise/counterclockwise to move
the Start Point forward or backward in small steps.
MEMO
• You can’t specify Start Point and End Point locations that
would cause the edited song to be less than four seconds
long.
• Slowly turn [DATA] to adjust the Start Point so that
you don’t hear the beginning of the sound.
60
Press
.
At the desired End Point, press
the CF card side.
on
7
8
5
6
The message “Are You Sure?” appears.
Four seconds of sound following the End Point will
play repeatedly.
Plays repeatedly
Four seconds
To execute the Trim In operation,
press
.
End Point
(If you decide to cancel, press
.)
The Trim In operation will be carried out. Once it’s
complete, you’re returned to the original readout.
Turn
to precisely adjust the End
Point.
• Turn [DATA] clockwise/counterclockwise to move
the End Point forward or backward in small steps.
• Slowly turn [DATA] to adjust the End Point so that
you don’t hear the end of the sound.
Trimming Silence from the End of a Track
Press
.
7
8
Use
or
to select the track you
The message “Are You Sure?” appears.
1
2
want to edit.
Press
until “TRIM OUT” appears in
the display.
To execute the Trim Out operation,
press
.
(If you decide to cancel, press
.)
The Trim Out operation will be executed. When it has
been completed, you’re returned to the original
readout.
Press
.
3
4
The trim out editing screen appears.
Number of the track you’re editing
On the CF card side, press
.
The track begins playing.
61
More Functions
Editing a CF Card (continued)
Insert the CF card that you want
to edit.
1
2
Preparations
common to all
CF card editing
operations
On the CF card side, press
.
4
5
Press the CF card
button to
The track will begin playing.
select the CF card as the source.
Dividing a Track (Divide)
Press
at the approximate location
where you want to divide the
track.
The contents of the CF card will change as follows.
1
2
Track number
Track number
MEMO
Four seconds of sound preceding this location will
play repeatedly.
A
B
3
Divide
1
2
Turn
to adjust the precise
location at which you want
to divide the track.
A’
B
A”
6
7
• Tracks that follow the location of the division will be
placed at the end of the CF card.
Press
.
• If the CF card does not have enough remaining free
space, you won’t be able to execute the Divide operation.
The message “Are You Sure?” appears.
• You can’t edit a track that is shorter than eight seconds.
To divide the track, press
.
8
Use
or
to select the track you
1
2
(If you decide to cancel, press
.)
want to divide.
The track will be divided. When the operation is
completed, you’re returned to the original readout.
Press
until “DIVIDE” appears in the
The new track is created at the end of the CF card. Play
display.
back the last track (
Press
.
3
The divide editing screen appears.
Number of the track you’re editing
62
Converting a Track to a Wave
File (Wave Convert)
Formatting a CF Card
If you turn off the power or subject the CF card to a strong
physical shock while the CD-2 is operating, the data in the CF
card may be damaged, and the system may stop operating
correctly.
Tracks that were recorded with a recording mode (
(WAV format) that can be handled by your computer or other
device.
If this occurs, re-format the CF card.
NOTE
MEMO
• Never turn off the power or remove the CF card while
formatting is being carried out. Doing so may destroy
the data on the CF card or render the CF card unusable.
• The new track produced by this conversion is placed at
the end of the CF card.
• If the CF card does not have enough remaining free
space, you won’t be able to execute the Wave Convert
operation.
• Formatting a CF card erases all data currently residing
on the card.
Press
appears in the display.
until “FORMAT CF CARD”
Use
or
to select the track that you
1
2
1
2
want to convert into a wave file.
Press
until “WAVE CONVERT”
appears in the display.
Press
.
The message “Are You Sure?” appears.
Press
.
3
The message “Wave Convert?” appears.
Press
.
3
4
Track number of the source
The message “You’ll Lose Data. Really Sure?” appears.
Track number of the
conversion result
• The message “Already WAV Trk” will appear if the
track you selected in Step 1 was recorded with a
recording mode of “WAV,” and you will be
returned to the original readout. Select a different
track.
To format the card, press
.
(If you decide to cancel, press
.)
Formatting begins. Once the formatting has been
successfully completed, the following screen appears.
To execute the conversion, press
.
4
(If you decide to cancel, press
.)
The track is converted to a wave file. When the
conversion is finished, you’re returned to the original
readout.
63
More Functions
Erasing Tracks from a CD-RW Disc
If you’re using a CD-RW disc, you can erase previously
Erasing All Tracks
recorded tracks.
• You can’t erase tracks from a CD-R disc.
Here’s how to erase all tracks from the CD-RW disc.
Insert the CD-RW disc from
which you want to erase
tracks.
Preparations common
to all CD-RW editing
operations
MEMO
• If the CD-R/RW disc has been finalized (
finalization will automatically be removed when you
erase all tracks.
NOTE
• You can’t recover a track that’s been erased. Use caution
before executing these operations.
Press
until “ERASE ALL TRACKS”
1
2
appears in the display.
Erasing the Last Track
Here’s how to erase the last track recorded on the CD-RW
disc.
MEMO
Press
.
• If you want to erase a track from a CD-RW disc that’s
been finalized (
finalization (
The “Are You Sure?” message appears.
Press
until “ERASE LAST TRACK”
1
2
appears in the display.
Press
.
3
4
The “Really Sure?” message appears.
Press
.
The “Are You Sure?” message appears.
To erase all tracks, press
.
(If you decide to cancel, press
.)
The tracks will be erased. During this process, a timer
is displayed, counting-down the time until the
operation is completed.
To erase the last track, press
.
3
(If you decide to cancel, press
.)
The track is erased. During this process, a timer is
displayed, counting-down the time until the operation
is completed.
Counting-down
When all tracks have been erased, you’re returned to
the original readout.
Counting-down
When the track has been erased, you’re returned to the
original readout.
64
Removing Finalization
You can remove finalization from a CD-RW disc (
so that the disc can once again be used for recording.
MEMO
• You can’t remove finalization from a CD-R disc.
• Removing finalization will not erase the recorded tracks.
Press
until “UNFINALIZE” appears in
1
2
the display.
Press
.
The message “Are You Sure?” appears.
To remove finalization, press
.
3
(If you decide to cancel, press
.)
Finalization is removed from the disc. During this
process, a timer is displayed, counting-down the time
until the operation is completed.
Counting-down
When finalization has been removed, you’re returned
to the original readout.
65
More Functions
Tuning Your Instrument (Tuner)
You can use the CD-2’s chromatic tuner function to tune your
instrument.
Tune the string so that the left and right
tuning guides are both displayed.
4
The tuner function can be used with any of the CD-2’s inputs,
including the internal mics.
If the string is tuned within +/-50 cents of the correct
pitch, tuning guides are displayed in the screen,
indicating the distance between the actual pitch and
the displayed note name.
MEMO
• You can’t play back or record while using the tuner.
• The effect (
the tuner.
• If you don’t want to hear the sound while using the
tuner, you can turn down the [OUTPUT LEVEL] knob
Tuning guides
(
sound (
When only the right guide
is displayed:
Tuning your electric guitar.
Example
The pitch is above the
displayed note name (i.e.,
sharp).
Connect your guitar to the
GUITAR jack.
1
2
Preparations
When only the left guide
is displayed:
Repeatedly press [MIC SELECT]
The pitch is below the
displayed note name (i.e.,
flat).
When both the right and
left guides are displayed:
The pitch matches the
Press
until “TUNER” appears in the
1
display.
displayed note name.
Repeat Steps 2–4 to tune each of your
instrument’s strings.
5
Play a single note on the open string you
want to tune.
2
MEMO
• If you’re tuning a guitar that has a vibrato tailpiece,
tuning one string may cause other strings to drift out of
tune.
The screen will show the name of the closest note to the
pitch you played.
If so, start by tuning each string to the approximate
pitch, and then continue tuning each string in turn until
they are all at the correct pitch.
Note name
• You must cleanly play a single note on only the
string you want to tune.
When you’re finished using the tuner,
6
press
.
Tune the string so that the correct note
name for that string appears in the screen.
3
You’re returned to the previous readout.
• Conventional tuning
6th
5th
4th
3rd
2nd
1st
string string string string string string
Guitar
Bass
E
A
D
E
G
A
B
E
D
G
66
Changing the Tuner’s Reference
Pitch
Listening to a Guide Tone While
Tuning
You can calibrate the CD-2’s Tuner to another instrument or
tuning standard by adjusting its “reference pitch.”
As a tuning aid, you can have the CD-2 sound a guide tone
from the internal speakers.
The reference pitch is the frequency of the A4 note. For
example, this is the pitch of the middle A note on a piano.
Press
until “Tone” appears in the
1
2
display.
Press
until “TUNER” appears in the
1
You will hear the guide tone shown in the screen.
display.
Guide tone
Reference pitch
Turn
to select the guide tone you
want to hear.
Turn
to change the reference
pitch.
2
3
• You can choose one of 25 chromatic notes in the
range A3–A5.
• You can adjust this in a range of 435–445 Hz.
Tune your instrument to the guide tone.
When you’re finished adjusting the
reference pitch, press
3
4
.
You’re returned to the previous readout.
To stop the guide tone, press
.
You’re returned to the previous readout.
MEMO
• The reference pitch for the guide tone can be adjusted in
67
More Functions
Copying an Original Music CD
You can use the CD-2 to copy a CD containing your original music.
Copyright
• Unauthorized recording, distribution, sale, lending, public performance, broadcasting, or the like, in whole or in part,
of a work (musical composition, video, broadcast, public performance, or the like) whose copyright is held by a third
party is prohibited by law.
• This unit is designed for professional use. When using the CD-R/RW drive to transfer audio signals, this unit can
perform recording without being subject to the restrictions of the Serial Copy Management System (SCMS). This is
because the unit is intended solely for musical production, and is designed not to be subject to restrictions as long as it
is used to record works (such as your own compositions) that do not infringe on the copyrights of others. (SCMS is a
feature that prohibits second-generation and later copying through a digital connection. It is built into MD recorders
and other consumer digital-audio equipment as a copyright-protection feature.)
• Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility
whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit.
About the License Agreement
• The CD-2’s CD-writing functionality, and its copying functionality are designed to allow you to reproduce material to
which you have copyright, or material which the copyright owner has granted you permission to copy. Accordingly,
reproduction of Music CD or other copyrighted material without permission of the copyright owner avoiding technical
prohibiting features of second-generation and later copying like SCMS or others constitutes copyright infringement and
may incur penalties even in case such reproduction is for your own personal use and enjoyment (private use). Consult
a copyright specialist or special publications for more detailed information on obtaining such permission from
copyright holders.
■ Workflow to Copy CDs
MEMO
When copying a music CD, the CD tracks are stored
temporarily on the CF card. Then, the temporary tracks
on the CF card are written to a blank CD-R/RW disc.
• You can’t copy a CD-R/RW disc that has not been
finalized (
• Music CDs that do not contain silence between tracks
will be copied with two seconds of silence inserted
between each track (see illustration below). In some
cases, this may mean that the copy will not be identical
to the original music CD.
Your original music CD
Blank
CD-R/RW disc
Original
Music CD tracks
Track01 Track02 Track03
music CD
CD-R/RW Track01
Disc
Track02
Track03
CF card
Silence (two seconds)
• The music CD tracks stored on the CF card will be
erased after they have been written to the blank
CD-R/RW disc.
NOTE
• The music CD’s tracks will be stored up to the amount of
free space available on the CF card. You may not be able
to copy an entire CD if there’s not enough free space
remaining. If you use a CF card with 1 GB of free space,
you will be able to copy an entire music CD.
68
Insert a CF card to hold the music
CD tracks.
Preparations
To proceed copying, press
.
5
6
(If you decide to cancel, press
.)
Press
until “CD COPY” appears in
The CD-2 will begin writing the data to the disc.
1
the display.
When the data has been written successfully, the
CD-R/RW disc is ejected and the “Another Disc?”
message appears.
• You can also select this item by turning [DATA].
Press
.
2
3
If you want to write the data to another
The message “Insert Master CD” appears.
CD-R/RW disc, press
.
The “Insert Blank CD” message appears.
Insert the music CD that you want to copy.
Insert another blank CD-R/RW disc, and the “CD
COPY. Are You Sure?” message appears.
The music CD’s tracks will be stored on the CF card.
The display will indicate the progress.
Return to Step 5 and continue the procedure.
Track currently being copied/
Total number of tracks to be copied
If you’re finished writing, press
.
Progress (per track)
You’re returned to the previous readout.
Play back the newly written CD-R/RW disc (
When the music CD’s tracks have been stored on the
CF card, the “Insert Blank CD” message will appear,
and the music CD will be ejected.
■ If the screen indicates “Copy ##/xx Tr. Are
You Sure?” in Step 3
The music CD’s tracks will be written as far as the free
space on the CF card allows. This means that if the CF
card contains less free space than the amount of data
from the music CD, you won’t be able to record all of the
tracks.
Remove the music CD, and insert a blank
CD-R/RW disc.
4
In this case, the message “Copy ##/xx Tr. Are You
Sure?” will appear. This indicates that of the total
number of tracks (xx), only track one through track ##
will be copied.
When the disc has been detected, the “Are You Sure?”
message appears.
Number of tracks to be copied/
Total number of tracks on CD
•
If the display indicates “Short of Capa”
If the capacity of the CD-R/RW disc is less than the
amount of data stored on the CF card, the message
“Short Of Capa” will appear, and the CD-R/RW
disc will be ejected. Please insert a CD-R/RW disc
with more writable space.
Verify the number of tracks for recording, and press
[ENTER] to continue the procedure. If you decide to
cancel, press [EXIT].
69
More Functions
Applying Effects to Your Vocal or Instrumental Performance
You can apply a variety of effects (acoustical processing) to
your vocal or instrumental performance.
Repeatedly press
to select the
1
For example, you can apply echo to your vocal, or apply
distortion to the sound of your electric guitar.
desired patch group.
The CD-2 provides a variety of preset patches that are suitable
for different instruments, and these are organized by category
into three groups. Use the effect patch that’s appropriate for
your instrument and situation.
Each time you press the button, the selection will
change as follows.
• If anything other than “Off” is selected, the effect
will be on and the [EFFECT] button will light.
• DYNAMICS group:
For various instruments.
Off
• VOCAL group:
For vocal/various instruments.
• GUITAR/BASS group: For guitar/bass/guitar + vocal.
Dynamics
DYN
MEMO
• You can freely select effects regardless of the group.
• Effects will not be applied to the instrument or audio
source connected to the LINE IN jacks.
Vocal
VCL
• You can’t use an effect simultaneously with the
Guitar
GTR
•
Verifying which effects patch is currently selected
The patch that appears first when you press [EFFECT] is
the currently selected patch. After noting the name of the
patch, press [EXIT] to return to the original readout.
• If the Mastering Effects (
“Use EFFECT? MST will be Off” message appears.
• The following effect patches allow you to simultaneously
apply different effects to a guitar and a microphone.
When using these patches, set the “Ext MIC1/2 Pan”
When you press [ENTER], the Mastering Effects
are turned off, and the effect screen appears.
parameter to “L/R” (
to the GUITAR jack and a mic to the MIC 2 jack.
Turn
to select the patch you want.
-
-
-
-
-
-
-
-
JC-120+COMP
CRUNCH+COMP
BLUES+COMP
HVY CM + VO
S-PZO+DL EFX
SIM+50msDL
2
3
Input sound into the CD-2 and you will hear it
processed by the selected effect. Try out various
patches while you listen to the result, and choose the
patch that’s most suitable for your situation.
SIM+HVY CM
H-ENH+LNG DL
Press
.
You’re returned to the previous readout.
• If you want to turn off the effect, choose “Off” in
Step 1. The [EFFECT] button becomes unlit.
70
More Functions
Backing Up Tracks from a CF Card
You can back up all tracks (recorded data) from a CF card to a
Obtain the necessary number of
1
Preparations
CD-R/RW disc.
CD-R/RW discs for the backup.
If you’re using a high-capacity CF
card that holds 1 GB or 2 GB, the
data may be too large to fit on a
single CD-R/RW disc.
It’s a good idea to back up important tracks to a CD-R/RW
disc as a precaution against accidental damage or loss of the
CF card.
If so, the backup will span two or
more discs. Obtain the necessary
number of CD-R/RW discs before
you continue.
NOTE
• Roland Corporation will take no responsibility for any
loss of CF card tracks or recorded content that may result
from failure of the backup operation, and will not be
liable for any damages resulting from such loss.
Insert the CF card that you want
to back up.
2
Additionally, Roland Corporation does not make any
guarantee regarding the backed-up data, regardless of
the performance or the state of the CD-R/RW drive.
MEMO
Press
until “BACKUP CF→CD”
• The backup operation applies to all tracks on the CF
card. You can’t back up a single specific track.
1
appears in the display.
• You can use the following CD-R/RW discs for backup.
• You can also select this item by turning [DATA].
CD-R
OK
CD-RW
OK
An unused disc
A previously recorded disc
OK *
*
Once you’ve used a CD-RW disc for backup, no further
tracks can be added to the backup even if there is remaining
space on that disc. All data contained on the CD-RW disc
will be erased before the backup is performed.
Press
.
2
3
The “Insert Backup CD” message appears.
• In order to play or edit data that you’ve backed up to a
CD-R/RW disc, you’ll need to restore the backup data to
a CF card.
■ If the screen indicates “Insert CD” in Step 4
Insert the CD-R/RW disc.
If the CF card contains more data than can fit on a single
CD-R/RW disc, the backup will be performed across
multiple CD-R/RW discs.
When the disc has been detected, the “[ENTER] to
start” message appears.
In Step 4, the first CD-R/RW disc will be ejected. Then,
the message “Insert CD” will be displayed. Insert
another CD-R/RW disc. When the disc is detected,
writing will begin automatically.
As directed by the messages that appear, exchange
CD-R/RW discs to proceed with the backup.
To begin the backup, press
.
• If the backup of a single track spans more than one
CD-R/RW disc, you will be asked to insert the CD-R/
RW discs in the correct order when you execute the
4
(If you decide to cancel, press
.)
Recover operation (
The backup begins.
We recommend that you label each CD-R/RW disc with
the correct number to indicate the backup order.
When the backup is complete, the CD-R/RW disc will
be ejected, and you’re returned to the original readout.
■
If the screen indicates “CD-RW Erase?” in Step 4
If you are using a previously recorded CD-RW disc, the
“CD-RW Erase?” message appears.
If you press [ENTER], the existing data will be erased
from the CD-RW disc, and then the backup will begin.
71
More Functions
Recovering Backed-up Data (Recover)
Here’s how backed-up data from a CD-R/RW disc can be
recovered to a CF card so that it can be played or edited.
Use
or
to select the track that you
4
want to recover.
MEMO
• Backed-up data can be recovered to a CF card in units of
individual tracks.
• If a track with an identical title is recovered, a two-digit
number will automatically be appended to the title.
Track title
• The lower line of the screen indicates the track title
• You can’t recover data from a CD-R/RW disc if there is
no free space on the CF card.
(
• If the backup spans two or more CD-R/RW discs,
you won’t know which disc contains the track you
want to recover. You may need to swap discs in
order to find and select the track you want to
recover.
Insert the CF card to which you will
recover the backed-up data.
Preparations
Press [EJECT ( )] to eject the CD-R/RW disc, and
return to Step 2. Insert another CD-R/RW disc in
that backup set, and continue.
Press
until “RECOVER CD→CF”
1
appears in the display.
• You can also select this item by turning [DATA].
To recover the track you’ve selected,
5
press
.
(If you decide to cancel, press
.)
Recovery begins. When recovery is completed, you’re
returned to the original readout.
Press
.
2
3
The message “Insert Backup CD” appears.
■ If the screen indicates “Insert CD#” at Step 5
If the backup of one track spans two or more CD-R/RW
discs, the “Insert CD #” message appears. (“#” indicates
the disc number in the backup set.)
Insert disc number # of the backup set, and press
[ENTER]. Recovery begins.
Insert the CD-R/RW disc that contains the
data you want to recover.
As directed by the messages, exchange CD-R/RW discs
as you continue the recovery procedure.
When recovery has been completed, you’re returned to
the original readout.
When the CD-2 recognizes the CD-R/RW disc, the
following screen appears.
72
More Functions
Playing SMF (Standard MIDI File) Data
The CD-2 can play back SMF (Standard MIDI File) data from
a CD-R/RW disc, and transmit the MIDI data to an external
MIDI device (sound module or electronic keyboard) to play its
sounds.
Insert the CD-R/RW disc that contains the
SMF data.
1
• SMF data written on a CF card cannot be played.
When the CD-2 detects the CD-R/RW disc, the SMF
screen appears.
Name of the currently selected directory
Connection Example
SMF file name
• Up to eight characters of the directory or SMF file
name are displayed.
CD-2 rear panel
Directory name:
eight characters
L R
To analog
output jacks
File name:
To MIDI IN connector
eight characters extension
MIDI sound module
Turn
to select the SMF you want
to play.
2
3
Cautions When Creating an SMF Data Disc
• You can also press
or
to select the SMF.
Please observe the following points when you create an SMF
data disc for playback on the CD-2.
Toviewthedirectory
one level below
Press
Press
.
.
• We recommend that the file names and directory names
be no more than eight characters long. Double-byte
characters (e.g., Japanese) are not supported.
Toviewthedirectory
one level above
File name
Eight or fewer single-byte
characters + filename extension
Directory name
Eight or fewer single-byte
characters (no filename extension
allowed)
On the CD side, press
.
The SMF will play.
• Add a filename extension of “.MID” or “.mid” to the
SMF files.
• Write the data to the CD-R/RW disc in ISO9660 format.
• The CD-2 can play only Format 0 SMF files.
Format 0
Format 1
Format 2
Playable
Not playable
Not playable
73
More Functions
Restoring the Factory Settings (Initialize)
When you execute the Initialize operation, all settings will
Parameter Name/
Function
Pitch
Initial Value
revert to their factory settings. If the CD-2 does not operate as
you expect even when you follow the steps in this manual,
you may wish to execute the Initialize operation.
Button Name
Pitch
0
0
0
Key
Key
The table on the right shows the factory settings.
Speed
Speed
Center Cancel
Menu
[CENTER CANCEL] Off
LCD Contrast
Time Display
Show Track Title
Foot Switch
5
Press
until “INITIALIZE” appears in
Elapse
Off
1
SYSTEM
the display.
Play
On
• You can also select this item by turning [DATA].
Int MIC Auto Lvl
Int MIC Gain
Int MIC Bal
25
MIC
C
Ext MIC1/2 Pan
CF Rec Mode
Auto Rec Start
C/C
Standard
Off
Press
.
2
3
RECORDING Auto Marker
Auto Marker Time
Off
The message “Are You Sure?” appears.
5min
-60dB
Bell
120
Auto Marker Lvl
Sound
Tempo
METRONOME
Beat
4
Count-in (Beat)
LINE IN
Off
To execute the Initialize operation, press
.
On
CF Mix Level
0
AUIDO CD Mix Level
AUX OUT Select
AUX OUT Level
Pitch
0
(If you decide to cancel, press
.)
Mix
Fixed
440
The Initialize operation is executed.
When initialization has been completed, you’re
returned to the original readout.
Tuner
Effect
Tone
A4
Effect Patch
Off
Mastering Effect
Mic select
Mute
Mastering Effect
[MIC SELECT]
Off
Off (Unlit)
Off (Unlit)
Off
[SPEAKER MUTE]
REPEAT [1/ALL]
REPEAT [A-B]
Repeat
Off
74
More Functions
Other Functions and Settings
Displaying the Remaining Time
You can switch the display to show either elapsed time or
remaining time during playback and recording.
You can also switch the time display as follows.
When you press
from the main screen, the time display
Press
until “Time Display” appears in
1
2
will change as follows.
the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
■ While recording or in recording-standby
mode
Elapsed recording time
Turn
to select the time display that
will appear in the screen.
Remaining recording time on the entire
CF card or CD-R/RW disc
Elapse: During playback, the track’s elapsed
playback time is displayed.
During recording-standby/recording, the
track’s elapsed recording time is displayed.
■ While playing or stopped
Remain: During playback, the track’s remaining
Elapsed track playback time
playback time is displayed.
During recording-standby/recording, the
remaining recording time on the CF card or
CD-R/RW disc is displayed.
Remaining track playback time
Press
twice.
3
You’re returned to the previous readout.
75
More Functions
Other Functions and Settings (continued)
Specifying the Function of the
Foot Switch
Automatically Adjusting the
Input Level of the Internal Mics
(Auto Level Control)
You can use a separately sold foot switch (such as the Roland
DP-2 or BOSS FS-5U) to perform the following functions.
Auto Level Control is a function that automatically adjusts the
input level according to the loudness of the audio source
when you record via the internal mics.
• Start/pause track playback
• Assign track numbers (only during recording)
It is convenient to use Auto Level Control when you’re
recording material that consists mainly of speaking voices,
such as a lecture.
You can choose one of the above functions for the foot switch
to control.
• When the CD-2 is shipped from the factory, Auto Level
Control is turned “On.”
MEMO
• Connect the foot switch to the FOOT SW jack located on
the rear panel of the CD-2.
Press
until “Int MIC Auto Lvl” appears
1
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Press
until “Foot Switch” appears in
1
2
the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to select “On.”
2
3
Turn
to choose the function of the
foot switch.
Press
twice.
Play:
Performs the same function as
.
You’re returned to the previous readout.
Alternately start or pause playback each
time you press the foot switch.
MEMO
When in recording-standby mode,
alternately start or pause recording each
time you press the foot switch.
• If you want the recording to retain the original ambience
of the room, turn Auto Level Control “Off” in Step 2.
Then, adjust the internal mic input level manually.
Marker: Performs the same function as
during
recording.
A track number will be assigned at the time
location where you press the foot switch
during recording.
Press
twice.
3
You’re returned to the previous readout.
76
Adjusting the Output Level from the AUX OUT Jacks
Choosing the Audio Source that is Output
from the AUX OUT Jacks
Adjusting the Output Level of the AUX OUT
Jacks
Here’s how to choose the audio source that will be output
from the CD-2’s rear panel AUX OUT jacks.
Here’s how to adjust the output level of the AUX OUT jacks.
Press
until “AUX OUT Level” appears
1
2
Press
until “AUX OUT Select” appears
in the display, and then press
.
1
2
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to select “Variable.”
Turn
to select the audio source
that is output from the AUX
OUT jacks.
Fixed:
The output level is fixed.
The audio signal selected for “AUX OUT
Mix:
MIC:
The audio of all sources is mixed and
output.
Select” (
level.
The audio from the MIC 1/MIC 2/GUITAR
jacks or the CD-2’s internal mics is output.
Variable: The [OUTPUT LEVEL] knob will adjust the
output level.
LINE:
CD:
The audio from the LINE IN jacks is output.
The audio from the CD is output.
CF:
The audio from the CF card is output.
Press
twice.
3
You’re returned to the previous readout.
Use the [OUTPUT LEVEL] knob to adjust the output
level of the AUX OUT jacks.
Press
twice.
3
You’re returned to the previous readout.
Electronic piano
HINT
• If you want to record your performance on an
electronic piano together with your voice, make
connections as shown below so that the sound from
the mic will also be output from the speakers of the
electronic piano.
INPUT
OUTPUT
At this time, set AUX OUT to “MIC” to prevent a
feedback loop from occurring between the CD-2 and
the electronic piano.
LINE IN
AUX OUT
Mic
MIC 1 or MIC 2
CD-2
77
More Functions
Other Functions and Settings (continued)
Switching the Line Input On/Off
Viewing the Track Titles
on a CF Card
When you’re using mics as well as instruments connected to
the LINE IN jacks, you may want to temporarily use only the
mics.
You can assign titles to the tracks on a CF card (
If you want to view the track titles, use the following
procedure.
If so, you can turn off the line input. Sound will no longer be
input from the LINE IN jacks, and only the sound from the
mics will be heard.
MEMO
• For wave files (WAV format) written by a computer to a
CF card (
Press
until “LINE IN” appears in the
1
display, and then press
.
Press
until “Show Track Title” appears
• You can also select this item by turning [DATA].
The following screen appears.
1
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to select “Off.”
2
3
Turn
to select “On.”
2
3
• Sound will no longer be input via the LINE IN jacks.
Press
twice.
Press
twice.
You’re returned to the previous readout.
You’re returned to the previous readout.
MEMO
Subsequently, when you switch tracks on the CF card,
the track title will be shown briefly, and then the time
display will reappear.
• The “Off” setting is temporary, and will be cleared when
you turn off the power. It will automatically be turned
“On” the next time you turn on the power.
If the title is so long that it cannot be displayed at one
time, it will scroll to display additional characters (up
to the first 27).
78
Adjusting the Playback Level of
a Music CD/CF Card
Here’s how to adjust the playback level of a music CD or CF
card.
• To adjust the playback level of a music CD
1
Press
until “CD Mix Level” appears
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
• To adjust the playback level of a CF card
Press
until “CF Mix Level” appears
in the display, and then press
.
• You can also select this item by turning [DATA].
The following screen appears.
Turn
to adjust the playback level.
2
• You can adjust the level in a range of -50–+25.
• A setting of “0” is the original playback level.
MEMO
• For tips on adjusting the playback level, refer to Step 2 of
Press
twice.
3
You’re returned to the previous readout.
Subsequently, the music CD or CF card will play back
at the level you specified.
MEMO
• You can also change the playback level temporarily.
79
80
Reference
Troubleshooting
If you suspect a malfunction, please check the following points. If this does not resolve the problem, contact a nearby Roland Service
Center.
■ Power Supply
See
Page
Problem
Cause and Action
The power does not turn
on when you press the
[POWER] switch.
● Could the AC adaptor plug have been disconnected from the CD-2’s AC adaptor
jack? Could the power cable have been disconnected from the AC outlet or the AC
adaptor’s connector?
➔ Firmly reconnect the AC adaptor and power cable.
■ Screen
See
Page
Problem
Cause and Action
The screen is difficult to
read
● Depending on the location or environment in which the CD-2 is placed, the screen
may be difficult to read.
➔ Readjust the display contrast.
—
Unreadable characters
appear on the screen
● Could the language of the display be set to “Japanese”?
➔ Change the Language setting to “English”.
■ Problems with the Sound
See
Page
Problem
Cause and Action
No sound
● Could the connections be incorrect?
➔ Make the correct connections.
● Could the power on the connected equipment (mic, digital piano, etc.) be switched
off?
➔ Turn on the power.
—
—
—
● Are condenser mics connected?
➔ If you’re using condenser mics, turn the CD-2’s phantom power switch “ON.”
● Could the volume of the connected device be turned down?
➔ Raise the volume of the connected device.
● Could headphones be plugged in?
➔ Unplug the headphones.
● Is the volume set to the minimum (MIN)?
➔ Use the [OUTPUT LEVEL] knob to raise the volume.
● Could speaker muting be on ([SPEAKER MUTE] button lit)?
➔ Press the [SPEAKER MUTE] button to defeat speaker muting (unlit).
The input source (audio
source) is not output
● Could the input level be set to the minimum?
➔ Use the appropriate knob for the MIC 1/MIC 2/GUITAR/LINE IN jacks to raise
the input level.
● Could the [MIC SELECT] button be lit green?
➔ If the internal mics are the input source ([MIC SELECT] button lit green), the
sound of the internal mics is not output from the speakers. Use headphones to
monitor the sound of the internal mics.
82
■ Problems with the Sound (continued)
See
Page
Problem
Cause and Action
The input source (audio
source) is not output
● Could devices be connected to both the MIC 1 jack and GUITAR jack?
➔ If you connect devices to both the MIC 1 jack and the GUITAR jack, the sound
from the MIC 1 jack will not be input. If you want to input sound from the MIC 1
jack, remove the plug from the GUITAR jack.
● Could the setting of the [MIC SELECT] button be incorrect?
➔ Use the setting that’s appropriate for the input source.
—
● Could the line input be turned off?
➔ Turn the LINE IN “On.”
Insufficient volume from a
device connected to the
MIC 1/MIC 2/GUITAR/LINE
IN jacks
● Could you be using a connection cable that contains an internal resistor?
➔ Use a connection cable that does not contain an internal resistor (such as one from
the Roland PCS-series).
The sound recorded via
the internal mics is not
loud enough
● Did you adjust the input level of the internal mics?
➔ Use Int MIC Gain to raise the input level of the internal mics.
The recorded sound is
noisy or distorted
● Is the input level adjusted appropriately?
➔ Adjust the input level so that the level meter briefly reaches “-3 dB” when loud
sounds are input.
● Could you have raised the input level for sources that are not connected?
➔ Even if no equipment is connected, we recommend that you set the input level to
—
the minimum (MIN) for all inputs that you are not recording.
● Could the [MIC SELECT] button be lit orange?
➔ Even if you are intending to record via external mics, a noisy recording may
indicate that you are actually recording from the internal mics. Set the [MIC
SELECT] button to the correct position for the audio source you intend to record.
● When recording the sound from an instrument connected to the LINE IN jacks,
could you be unintentionally recording the sound from another CD-2 source as
well?
➔ When recording only the sound from the LINE IN jacks, make sure that [MIC
SELECT] is off (unlit).
● Could you be applying a mastering effect while creating a music CD?
➔ Some mastering effect patches may cause noise or distortion when used with
certain types of material. Try changing to a different mastering effect patch.
● Is the output level set correctly?
➔ If you raise the output level too high, noise or distortion may occur in the sound
from the internal speakers. Use the [OUTPUT LEVEL] knob to adjust the volume.
An unwanted effect is
applied to the sound
● Could you have selected an effect?
➔ Turn the effect “Off.”
—
● Could a mastering effect be selected?
➔ Turn the mastering effect “Off.”
Sound is briefly heard
from the internal speakers
even though they are
muted
● Were you connecting or disconnecting headphones?
➔ If the speakers are muted (the [SPEAKER MUTE] button is lit), noise may be heard
from the internal speakers when you connect or disconnect the headphones; this
is not a malfunction.
83
Reference
Troubleshooting (continued)
■ CD-Related Problems
See
Page
Problem
Cause and Action
Normal playback does not
work
● Could the CD be upside down?
➔ Insert the CD with the label facing upward.
—
● Could you have inserted a CD on which nothing has been recorded?
➔ Insert a different disc.
● Could you be using Repeat playback?
➔ Press [1/ALL] enough times to get the Repeat icon (
/
) to disappear.
● Could you be using A-B Repeat playback?
➔ Press [A-B] to get the A-B Repeat icon (
) to disappear.
➔ Alternatively, press the CD [Stop ( )] to stop playback. A-B Repeat playback will
be defeated.
● Could the playback speed have been changed?
➔ Set the Speed setting to “0” so that the Speed icon (
) disappears.
) disappears.
—
● Could the Pitch setting have been changed?
➔ Set the Pitch setting to “0” so that the Pitch icon (
● Could the Key setting have been changed?
➔ Set the Key setting to “0” so that the Key icon (
) disappears.
● Could Center Cancel be turned “On”?
➔ Press [CENTER CANCEL] so that the Center Cancel icon (
) disappears.
● Could the CD be damaged?
➔ Try playing a different CD.
● Could the CD [Play (
)] button be blinking?
➔ If the button is blinking, the CD is paused. Press [Play (
)] to defeat pause.
Insufficient playback
volume
● Could the CD playback level be turned down?
➔ Use CD Mix Level to raise the playback level.
Can’t record
● Could the CD be upside down?
➔ Insert the CD with the label facing upward.
● Could you be attempting to record on a CD-R/RW disc that has already been
finalized?
➔ Use a blank or appendable CD-R/RW disc.
—
➔ If you want to record on a CD-R/RW disc that has already been finalized, you’ll
need to remove finalization so that the disc can be recorded to again.
● Is it possible that the maximum recordable time or number of tracks (CD-R:
maximum of 99 tracks, CD-RW: maximum of 98 tracks) has already been exceeded?
➔ If there are unwanted tracks on the disc, delete them before you continue
recording. (This is only possible on a CD-RW disc.)
● Could you be attempting to record or erase a CD-RW disc more times than it is
capable of?
➔ A CD-RW disc can be recorded and erased approximately one thousand times.
—
● Could you be attempting to record an extremely short performance?
➔ You can’t record for less than four seconds.
84
■ CD-Related Problems (continued)
See
Page
Problem
Cause and Action
Can’t record (continued)
● Are you using a generic CD-R/RW disc?
➔ Use a CD-R/RW disc from a recommended manufacturer.
—
After recording, the CD
won’t play back on a
conventional CD player
● Did you finalize the disc after recording?
➔ Execute the Finalize operation.
● Is your CD player able to play back CD-R or CD-RW discs?
➔ If your CD player does not support CD-R or CD-RW discs, they may not play back
correctly.
SMF data written to a
CD-R/RW disc is not
recognized
● Could the filename contain double-byte (e.g., Japanese) characters?
➔ Filenames containing double-byte (e.g., Japanese) characters will not be
—
recognized.
The disc tray will not open ● Is the CD-2 powered up?
➔ Turn on the power of the CD-2.
If a power failure has occurred, you can use the emergency eject hole to open the
disc tray manually.
CD-R/RW drive produces
significant mechanical
noise when operating
● Could you be using a high-speed compatible CD-RW disc?
➔ If you’re using a high-speed compatible CD-RW disc, performing the following
operations will cause the disc to rotate at high speed, producing a greater level of
mechanical noise. This is not a malfunction.
—
• When you stop recording
• When you delete a track
• When you assign a song number
• When you finalize
If you find the mechanical operating noise of the CD-R/RW drive objectionable,
please use an 8x compatible CD-R disc or a 1-4x compatible CD-RW disc.
■ CF Card-Related Problems
See
Page
Problem
Cause and Action
The CF card is not
detected
● Could the CF card be of a capacity that is not supported?
➔ Check the capacity of the CF card, and use a card of a capacity supported by the
CD-2.
● Is the CF card inserted all the way into the slot?
➔ Make sure that the card is oriented correctly, and that it is pushed all the way into
the slot.
● Could you have turned off the power while recording, or could the CF card have
been subjected to strong impact?
➔ It is possible that the data has been damaged. Reformat the CF card.
—
The CF card won’t play
back
● Could you have inserted a CF card on which nothing has been recorded?
➔ Insert a different CF card.
● Could you be using Repeat playback?
➔ Press [1/ALL] enough times to turn off the Repeat icon (
/
).
● Could you be using A-B Repeat playback?
➔ Press [A-B] to get the A-B Repeat icon (
➔ Alternatively, press the CF card [Stop ( )] to stop playback. A-B Repeat playback
) to disappear.
will be defeated.
● Is the CF card [Play (
)] button blinking?
➔
If the button is blinking, the CF card is paused. Press [Play (
)] to defeat pause.
85
Reference
Troubleshooting (continued)
■ CF Card-Related Problems (continued)
See
Page
Problem
Cause and Action
Insufficient playback
volume
● Could the CF card playback level be set to the minimum?
➔ Adjust CF Mix Level to raise the playback level.
Can’t record
● Is the CF card inserted all the way into the slot?
➔ Make sure that the card is oriented correctly, and that it is pushed all the way into
—
the slot.
● Could you be attempting to record an extremely short performance?
➔ You can’t record for less than four seconds.
● Is it possible that the maximum recordable time or number of tracks (maximum of
99 tracks) for the card has been exceeded?
➔ If there are unwanted tracks on the card, delete them before you continue
recording.
The recording time is too
short
● Have you selected the correct recording mode?
➔ The available recording time will depend on the recording mode. Choose the
recording mode that’s appropriate for the material you’re recording.
It takes a long time to
erase a track
● Could you be erasing a long track?
➔ The amount of time needed to erase a track will depend on the length of the track
and on the recording mode (
The following table shows the time required to erase a track that is three hours long.
Recording mode
Standard
Long
WAV
Time required for erasure Approx.
Approx.
Approx.
1 minute
30 seconds
45 seconds
3 minutes
Wave files written using
your computer are not
recognized
● Could the wave files be too short?
➔ Wave files shorter than four seconds will not be recognized.
—
—
● Could the filename contain double-byte characters (e.g., Japanese) or “~” (tilde)?
➔ Filenames containing double-byte characters (e.g., Japanese) or “~” (tilde) will not
be recognized.
■ Other problems
See
Page
Problem
Cause and Action
You hear noise when
playing a file from a CF
card track on your
computer
● Could you be playing a file with a filename extension of “.DAT”?
➔ “.DAT” files are in a special format used only by the CD-2. Do not attempt to play
—
them on your computer.
86
Reference
Messages
If a message is displayed, refer to the following list and take the appropriate action.
Message
Blank Disc
Content
The disc is blank (empty).
Action
Use a CD-R/RW disc that is not blank.
CD Disc Busy
CD Disc Full
CD Track Full
The disc could not be read/written in time.
If this appears during playback, use an
unscratched disc. If this appears during
recording, use a recommended brand of disc.
The disc is full. No more tracks can be recorded.
Record on another disc.
Delete unwanted tracks to increase the free space
(CD-RW disc).
You have reached the maximum number of tracks Record on another disc.
(CD-R: 99, CD-RW: 98) that can be recorded on a
disc. No more tracks can be recorded.
Delete unwanted tracks to increase the free space
CD Read Failed
CD Write Failed
CF Can’t Format
CF Card Full
Failed to read a disc.
Use a disc that is not scratched.
Use a recommended brand of disc.
Use a different card.
Failed to write a disc.
Failed to format the card.
The card is full. No more tracks can be recorded.
Delete unwanted tracks to increase the free space.
CF No Enough Mem
CF Track Full
The card does not have enough free space for the
operation.
Delete unwanted tracks to increase the free space.
You have reached the maximum number of tracks Delete unwanted tracks to increase the free space.
(99) that can be recorded on a CF card. No more
tracks can be recorded.
CF Was Removed
The CF card was removed while reading or writing. Turn the power off, and then on again; if normal
operation does not resume, format the card.
Count-in REC
Divide Multiple
Recording will begin after a count-in.
—
—
The track will be divided for writing on multiple
discs.
Finalized Disc
Improper Disc
The disc has been finalized.
Use an unfinalized CD-R/RW disc.
The disc is an inappropriate type for the operation Use a disc that is appropriate for the operation.
you are attempting to perform.
Not A CD-RW
No Title
The disc is not a CD-RW disc.
No title has been entered.
Use a CD-RW disc.
Assign a title of one character or more.
Each recording must be longer than four seconds.
REC Too Short
You can’t stop recording because the elapsed
recording time has not reached four seconds.
The track number can’t be assigned because the
Assign track numbers at intervals of four seconds
location selected is less than four seconds after the or greater.
previous track number.
Same Name Exists
SMF Too Big
A track with the same name exists on the CF card.
Cannot assign the name to the track.
Assign a unique name to the track.
The SMF file exceeds the size (1 MB) that the CD-2 Use an SMF file that the CD-2 is able to play.
can play. Playback is not possible.
Short Of Capa
Tr is Too Short
Unknown Disc
You can’t assign a CF track that exceeds the
available CD-R/RW disc space.
Either use another disc, or assign a smaller CF
track.
You can’t trim or divide because a track can’t be
shorter than four seconds.
—
The disc cannot be used with the CD-2.
Confirm that the disc can be used.
Unsupported CF
Unsupported File
Waiting Signal..
The CD-2 is unable to use this CF card.
The CD-2 is unable to play this SMF file.
Waiting for audio input to trigger recording.
Use a different card.
The CD-2 can play only Format 0 SMF files.
To begin recording, input an audio signal.
87
Reference
Effect Patch List
■ DYN (Dynamics Group)
Patch Name
Function
Compressor
Limiter
De-Esser
Basic control of audio dynamic range.
Basic control of extreme peaks in audio dynamic range.
Removes sibilance and harshness from the voice.
Noisy Room
Loud Voice
Soft Voice
Piano
Use to improve sound intelligibility on recordings made in noisy environments.
Controls extreme peaks in loud speaking or singing.
Controls overall dynamic range of subtle singing or speaking.
Enhances and controls the dynamic range of an acoustic piano for better clarity.
Smoothes out the dynamic range of a drum kit recording.
Use when recording a rock or pop band with heavy amplification.
Use for recording a live performance of a jazz band.
Use for recording a live concert of a band or orchestra.
Use on audio with constant extremes in loudness and softness.
Maximized sound level and tonal character suitable for dance music.
Slow modulation effect.
Drum Kit
Rock Band
Jazz Band
Orchestra
Squish!
CMP+FAT EQ
LO&SLOW FLNG
ST CHORUS
PS:DETUNE
ST DOUBLER
Deep and spacious sound produced by a chorus effect.
Pitch-shifted sound added to create depth.
Doubling applied to produce a spacious sound.
CHORUS+DELAY Chorus and delay combined to enhance the spatial spread.
1920’s RADIO
1960’s RADIO
VINTAGE 45’s
CLASSIC LP
Simulates the sound of an antique radio that’s not tuned correctly.
Simulates the sound of a noisy old radio.
Simulates the sound of a 45 RPM single played on an antique phonograph.
Simulates the sound of an LP played on a turntable.
■ VCL (Vocal Group)
Patch Name
Function
Reverb SHall
Reverb LHall
Reverb SRoom
Reverb LRoom
Reverb Plate
LONG ECHO
MID ECHO
Simulate the reverberation in a small hall.
Simulate the reverberation in a large hall.
Simulate the reverberation in a small room.
Simulate the reverberation in a large room.
Simulate the reverberation of a metallic board.
Long echo.
Medium echo.
SHORT ECHO
KARAOKE VOX
Vocal FX
Male Vocal
Rock Male
Short echo.
Simulate KARAOKE VOX.
Basic setup for recording or mixing vocals.
Controls harsh mids and improves the tone quality of a male vocal.
Adds spaciousness and energy to male vocal.
Adds an overall mellow sound to the voice.
Smoothes out harsh mids and adds sparkle to upper frequencies.
Adds spaciousness and energy to female vocal.
Adds smoothness and warmth to female jazz performance.
An effect similar to increasing the number of vocalists.
Heavy compression to even out the voice for video and radio dialogue.
Removes low end rumble and “plosives” from vocals miked too close.
Adds crispness and sizzle to vocals for more presence.
Adds a double tracking effect to the vocal.
Jazz Male
Female Vocal
Rock Female
Jazz Female
Big Chorus
Narration
Low Cut
Sparkle
Vox Double
88
Patch Name
Function
Unison VOX
M&F Duet
VOX Detune
CHIPS & MUNK
Deep Voice
Adds a octave down voice to the vocal.
Transforms a voice into a male part and female part.
Adds a detune voice to the vocal.
Pitch shifting effect that raises the octave of the voice.
Pitch shifting effect that lowers the octave of the voice.
■ GTR (Guitar/Bass Group)
Patch Name
Function
JC Clean
Roland JC-120. Use chorus on the mixdown.
Rock Lead
Straight-ahead distortion sound with delay.
TW Clean
TEXAS
Driven Lead
Metal Lead
American-made vacuum tube combo amp from the black-face period.
Driven sound of an American-made vacuum tube amp from the 50’s.
Replica of a British combo amp modified for high gain.
A lead sound suitable for metal.
SWEET LEAD
Delayed Lead
80’s Hard
Large vacuum tube amp stack popular in British hard rock of the 70’s.
Straight-ahead distortion sound with delay.
Powerful high-gain metal sound.
90’s Metal
Large vacuum tube amp popular for American heavy metal.
7TH STRINGS?
JAZZ GT
The sound of a large vacuum tube amp for heavy metal using a seven-string guitar.
The sound of a vacuum tube combo amp.
PH CRUNCH
JET FLANGER
AC SimCuttin
ACOUSTY
AC Sim Lead
Brite Acustc
Tight Bass
Natural-sounding crunch distortion.
Distortion with a metallic-sounding flanging effect.
A tone with a strong attack that won’t get buried by other instruments in the band.
Use this with a humbucking pickup guitar to obtain the tone of an acoustic guitar.
Use this with a single-coil pickup guitar to obtain the tone of an acoustic guitar.
Simulates the sound of the pickups installed in an electric-acoustic. A compressor is lightly applied to the attack.
Transforms an electric guitar into a crisp-sounding bass guitar.
Transforms an electric guitar into the sound of a bass guitar strung with heavy strings.
Simulates a fat-sounding acoustic guitar.
Loose Bass
A.GTR Fat
A.GTR LEAD
MIC’D ACUSTC
WIDE ACUSTC
SLAP’n POP
FRETLESS B.
PHASE BASS
FLANG BASS
STD BASS
Simulates an acoustic guitar suitable for lead playing.
Produces the sound of an acoustic guitar recorded through a mic.
Simulates an acoustic guitar with a wide left/right spatial spread.
Hard-compressed sound suitable for slap playing.
Simulates a fretless bass.
Produces the sound of a bass with a phaser effect applied.
Produces the sound of a bass with a flanger effect applied.
Produces the vintage sound of an early transistor amp.
DRIVIN’ BASS
JC-120+COMP
CRUNCH+COMP
BLUES+COMP
HVY CM + VO
S-PZO+DL EFX
SIM+50msDL
SIM+HVY CM
H-ENH+LNG DL
A large double-stack vacuum tube amp with a distinctive ultra-low sound and edge.
An algorithm for simultaneously recording a guitar sent through the JC-120 together with a vocal.
Suitable for simultaneously recording a crunch sound with natural distortion together with a vocal.
Suitable for simultaneously recording a midrange lead sound suitable for blues together with a vocal.
Suitable for simultaneously recording the Liverpool sound of the 60’s together with a vocal.
Suitable for simultaneously recording an electric-acoustic pickup simulation together with a vocal.
Suitable for simultaneously recording the sound of a large-bodied acoustic guitar together with a vocal.
Suitable for simultaneously recording an acoustic guitar with a strong attack together with a vocal.
Suitable for simultaneously recording an acoustic guitar sound together with a vocal with a long delay applied.
89
Reference
Menu List
The following table shows the various menus that are displayed when [MENU] is pressed.
Upper Line
[SYSTEM]
Lower Line
LCD Contrast
See Page
—
Time Display
Show Track Title
Foot Switch
Language
INITIALIZE
Int MIC Auto Lvl
Int MIC Gain
Int MIC Bal
[MIC]
Ext MIC1/2 Pan
CF Rec Mode
Auto Rec Start
Auto Marker
Auto Marker Time
Auto Marker Lvl
Sound
[RECORDING]
[METRONOME]
[AUDIO]
Tempo
Beat
Count-in (Beat)
LINE IN
CF Mix Level
CD Mix Level
AUX OUT Select
AUX OUT Level
BACKUP CF→CD
RECOVER CD→CF
CD COPY
[UTILITY]
90
Reference
Specifications
Recorder
Tracks
2 (Stereo)
Sample Rate
44.1 kHz
Signal Processing
Recording Mode
Recording Media
AD/DA conversion: 24 bits
Standard, Long, WAV
CompactFlash (16 MB–2 GB), CD-R, CD-RW
Standard
Long
6
2
WAV
1.5
3
16MB
32MB
64MB
128MB
256MB
512MB
1GB
3
6
12
24
49
98
196
392
24
49
98
196
392
784
6
12
24
49
98
196
Recording Time (unit: min)
2GB
*
*
The above-listed recording times are approximate. Times may varys slightly depending on the number
of songs that were created.
Maximum recording time of 1 song is 3 hours.
Recording Songs
Input/Output
Audio Input
Up to 99 songs on a single CompactFlash or CD-R/Up to 98 songs on a single CD-RW
Internal Stereo Microphone
MIC Input 1, 2 Jack: XLR-type with phantom power, 1/4 inch TRS phone-type
Guitar (Hi-Z) Jack: 1/4 inch phone-type, LINE Input Jacks (L, R): RCA phono-type
Internal Stereo Speaker, PHONES Jack: Stereo 1/4 inch phone-type,
AUX Out Jacks (L, R): RCA phono-type
Audio Output
Frequency Response
20 Hz–20 kHz (+0 dB/-2 dB)
MIC Input 1, 2 Jack: -63– -31 dBu
(maximum -19 dBu: balanced, maximum -13 dBu: unbalanced)
Guitar Jack (Hi-Z): -40– -9 dBu (maximum +3 dBu),
LINE Input Jacks (L, R): -2– +12 dBu (maximum +24 dBu)
Nominal Input Level (variable)
Nominal Output Level
Input Impedance
AUX Output Jacks (L, R): -8 dBu (maximum +4 dBu)
MIC Input 1, 2 Jack: 4 k ohms (balanced), Guitar Jack (Hi-Z): 1 M ohms,
Line Input Jacks (L, R): 9 k ohms
Output Impedance
AUX Output Jacks (L, R): 1 k ohms, Phones Jack: 10 ohms
Recommended Load Impedance AUX Output Jacks (L, R): 10 k ohms or greater, Phones Jack: 32 ohms
Other Input/Output Connectors MIDI Out Connector: 5-pin DIN type, Foot Switch Jack: 1/4 inch phone type
Effects
Dynamics group: 22 patches, Vocal group: 26 patches, Guitar/Bass group: 38 patches,
Mastering Tool: 25 patches
Others
Display
16 characters, 2 lines (backlit LCD)
302 (W) x 242 (D) x 76 (H) mm
11-15/16 (W) x 9-9/16 (D) x 3 (H) inches
Dimensions
3.1 kg
6 lbs 14 oz
Weight
Power Supply
Current Draw
AC Adaptor (PSB-3U)
3.0 A
Owner’s Manual, AC Adaptor (PSB-3U), Power Cord, CompactFlash (128 M bytes),
CD-R (Blank media), Card Protector
Accessories
Options
Foot Switch: FS-5U (BOSS), Pedal Switch: DP-2
*
*
(0 dBu = 0.775 V rms)
In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
91
Index
Numerics
E
Editing a CF Card
A
Erasing
B
F
C
CF card ...................................................................... 18, 29
CompactFlash card .........................................See CF card
G
I
Input level
Inserting
D
92
K
R
L
Removing
M
S
N
T
O
P
U
Play back a CD
V
Play back a CF card
W
93
Information
When you need repair service, call your nearest Roland Service Center or authorized Roland
distributor in your country as shown below.
PHILIPPINES
COSTA RICA
TRINIDAD
NORWAY
JORDAN
AFRICA
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
JUAN Bansbach Instrumentos
Musicales
AMR Ltd
Roland Scandinavia Avd.
AMMAN Trading Agency
245 Prince Mohammad St.,
Amman 1118, JORDAN
TEL: (06) 464-1200
Ground Floor
Kontor Norge
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
Ave.1. Calle 11, Apartado 10237,
San Jose, COSTA RICA
TEL: 258-0211
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: (02) 899 9801
KUWAIT
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 2273 0074
SINGAPORE
SWEE LEE MUSIC
COMPANY PTE. LTD.
150 Sims Drive,
SINGAPORE 387381
TEL: 6846-3676
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa
1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
CURACAO
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
REUNION
TEL: 243-6399
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 16-
5857
Beirut, LEBANON
TEL: (01) 20-1441
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
PORTUGAL
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
CRISTOFORI MUSIC PTE LTD
Blk 3014, Bedok Industrial Park E,
#02-2148, SINGAPORE 489980
TEL: 6243-9555
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
That Other Music Shop(PTY)Ltd.
11 Melle St., Braamfontein,
Johannesbourg,
SOUTH AFRICA
TEL: (011) 403 4105
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
OMAN
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TALENTZ CENTRE L.L.C.
P.O. BOX 37, MUSCAT,
POSTAL CODE 113
TEL: 931-3705
FAX: (011) 403 1234
EUROPE
TEL:(593-4)2302364
TEL: (02) 2561 3339
TEL: (266) 364 609
Paul Bothner(PTY)Ltd.
17 Werdmuller Centre,
Main Road, Claremont 7708
SOUTH AFRICA
QATAR
Al Emadi Co. (Badie Studio &
Stores)
P.O. Box 62, Doha, QATAR
TEL: 4423-554
EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final
Alameda Juan Pablo II,
Edificio No.4010 San Salvador,
EL SALVADOR
THAILAND
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l
107 564 Moscow, RUSSIA
TEL: (095) 169 5043
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2,
Bangkok 10100, THAILAND
TEL: (02) 2248821
TEL: (021) 674 4030
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
VIETNAM
Saigon Music
Suite DP-8
40 Ba Huyen Thanh Quan Street
Hochiminh City, VIETNAM
TEL: (08) 930-1969
TEL: 262-0788
SPAIN
ASIA
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
GUATEMALA
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
SWEDEN
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
TEL:(502) 599-2888
HONDURAS
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
AUSTRALIA/
NEW ZEALAND
TEL: (014) 575811
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
AUSTRALIA/
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
TEL: (2) 666 10529
TEL: (010) 6426-5050
TEL: (011) 223-5384
DENMARK
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
TURKEY
Ant Muzik Aletleri Ithalat Ve
Ihracat Ltd Sti
Siraselviler Caddesi
Siraselviler Pasaji No:74/20
Taksim - Istanbul, TURKEY
TEL: (0212) 2449624
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
TEL: 3916 6200
FINLAND
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
HONG KONG
Tom Lee Music Co., Ltd.
Service Division
22-32 Pun Shan Street, Tsuen
Wan, New Territories,
HONG KONG
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
CENTRAL/LATIN
AMERICA
UNITED KINGDOM
MEXICO
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
TEL: 2415 0911
TEL: (04) 3360715
UNITED KINGDOM
TEL: (01792) 702701
TEL: (55) 5668-6699
Parsons Music Ltd.
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
NORTH AMERICA
MIDDLE EAST
BARBADOS
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way
Richmond B. C., V6V 2M4
CANADA
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: (505)277-2557
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
PANAMA
TEL: (604) 270 6626
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook,
Panama City, REP. DE
PANAMA
TEL: 17 211 005
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
TEL: 315-0101
TEL: (23) 511011
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
PARAGUAY
Distribuidora De
Instrumentos Musicales
J.E. Olear y ESQ. Manduvira
Asuncion PARAGUAY
TEL: (595) 21 492147
TEL: (022) 66-9426
TEL: (905) 362 9707
IRELAND
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
IRAN
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
U. S. A.
KOREA
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
PERU
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
TEL: (021) 285-4169
TEL: (323) 890 3700
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha'aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
MALAYSIA
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
TEL: (574)3812529
Lima - Peru
TEL: (511) 4461388
As of January 15, 2005 (ROLAND)
Information
94
For EU Countries
For the USA
This product complies with the requirements of European Directive 89/336/EEC.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
234
*
CompactFlash and
are trademarks of SanDisk Corporation and licensed by CompactFlash association.
235
*
Roland Corporation is an authorized licensee of the CompactFlash™ and CF logo (
) trademarks.
236
*
Fugue © 2005 Kyoto Software Research, Inc. All rights reserved.
91-8464
3VT
|
