USER
MANUAL
User Manual
FCC Compliance Statement
NOTE:This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by switching the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The compliance of this unit to the FCC rules is not subject to any special
accessories, which are not readily available through normal dealer
channels.
The drive is in conformity with the EMC directive and low-voltage
directive.
CAUTION: Any modifications or changes made to this equipment not
expressly approved by the PLASMON group of companies may void
the authority to operate this equipment in its intended installation.
WARNUNG: Die Vollmacht, das Gerät in der vorgeschriebenen Weise
zu betreiben wird dann ungültig, wenn an dem Laufwerk
Veränderungen vorgenommen werden, die nicht von PLASMON
genehmigt wurden.
97705183 A
ii
User Manual
ATTENTION: Toute modification ou changement fait sur cet
équipement et non expressément approuvé par Plasmon peut
engendrer des disfonctionnements irréversibles et rendre son
installation impossible.
Thermal Precautions for the MOD910I
Forced air-cooling is required throughout the drive to prevent overheating of the drive and
must be provided as part of the system integration.
The following are precautions that should be observed when installing the MOD910I:
•
•
Do not cover the ventilation slot on top of the drive
Airflow should be from the rear of the unit. Air should not be drawn into the front
of the unit.
•
•
Ensure that a minimum airflow of 3 CFM is provided.
If possible, try to ensure that there is no device installed immediately above the
MOD910I.
Thermale Vorsichtsmassnahmen fur das MOD910I
Zwangsluftkühlung ist erforderlich, da es das Überhitzen des Laufwerks verhindert. Die
Kühlung muss in das System integriert werden.
Die folgenden Vorsichtsmassnahmen müssen bei dem Einbau des MOD910I beachtet
werden:
•
•
Die Ventilationsöffnung auf dem Laufwerk darf nicht abgedeckt werden.
Das Gerät muss von hinten belüftet werden. Das Gerät darf keine Luft von vorne
ansaugen.
•
•
Ein minimaler Luftfluss von 3CFM (~ 28dm3/min) ist erforderlich.
Wenn möglich, sollten keine Geräte direkt über dem MOD910I installiert werden.
Précaution thermique d’emploi pour le lecteur
MOD910:
Un refroidissement d’air forcé dans le lecteur est nécessaire au bon fonctionnement de
l’appareil. Il doit prévenir toute surchauffe et doit faire partie intégrante du système lors
de son intégration.
•
Veuillez trouver ci-dessous toutes les recommandations à observer lors de
l’installation du MOD910.
•
•
Ne pas recouvrir, ni obturer les systèmes d’aération du lecteur
La circulation d’air doit toujours être faite de l’arrière vers l’avant du lecteur. L’air
forcé par l’arrière doit mettre le lecteur en pression pour prévenir toute
introduction d’air par l’avant.
•
•
Vérifier que le flux d’air est au minimum de 3 CFM
Si possible, ne pas installer d’autre système immédiatement au dessus du
MOD910.
97705183 A
iii
User Manual
Laser Product
Class 1 Laser Product
The optical drive mechanism contained in this unit is certified to comply
with DHHS rule 21 CFR Chapter 1, Sub-chapter J in effect as of the
date for manufacture.
This optical drive mechanism is classified as a Class 1 laser product to
EN 60825, and there is no hazardous laser radiation with the safety
protection.
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Never open the enclosure or touch the parts internal to the product.
When the power switch is on, do NOT place your eyes close to the front
panel opening to look into the unit.
Laser Specification
Class 1 LASER mechanism
Laser Power: No hazardous radiation is emitted with the safety
protection of the unit.
97705183 A
iv
User Manual
Laser Produckt
Klasse 1 Laser Produkt
Der optische Laufwerksmechanismus, welcher sich in diesem Gerat
befindet, entspricht der DHHS Regel 21, Kapitel 1, Nebenkapitel J,
wirkend ab Herstellungs Datum.
Dieser optische Laufwerksmechanismus wird, entsprechend EN 60825,
als Klasse 1 Laser Produkt klassifiziert und gibt, mit Sicherheits Schutz,
keine schädliche Strahlungen ab.
Anwendung der Kontrollen oder Gebrauch dieses Gerätes anders wie
hier vorgeschrieben, können zu schädlicher Strahlenausetzung führen.
Das Gehäuse des Gerätes darf nicht geöffnet werden, auch dürfen die
Innenteile unter keinen Umständen angefasst werden.
Wenn das Gerät eingeschaltet ist, darf man nicht versuchen durch das
Öffnen der forderen Klappe in das Laufwerkinnere hinein zu sehen.
Laser Beschreibung
Klasse 1 Laser Mechanismus
Laser Antrieb: Mit Sicherheitsschutz gibt Gerat keine schädliche
Strahlungen ab.
97705183 A
v
User Manual
Produit laser
Produit laser de classe 1
Le mécanisme de lecture optique composant cette unité est certifié
conforme à la norme DHHS règle 21 chapitre 1, sous-chapitre J, en
vigueur à la date de fabrication.
Ce mécanisme de lecture optique fait partie des produits laser de
classe 1 conformément à la norme EN 60825, et ne produit aucun
rayonnement nocif grâce à son dispositif de sécurité.
Toutes vérifications, réglages ou procédures autres que ceux
mentionnés dans ce guide d’utilisation peuvent vous exposer à un
rayonnement nocif.
Ne jamais ouvrir le boîtier du lecteur et évitez tout contact avec les
composants internes du produit.
Lorsque l’appareil est sous tension, n’essayez jamais de regarder à
l’intérieur de l’unité par l’ouverture du panneau frontal.
Spécification du laser
Mécanisme laser de classe 1
Puissance laser : aucun rayonnement nocif n’est émis grâce au
dispositif de sécurité intégré à l’unité.
97705183 A
vi
User Manual
Unpacking / Packing
(1)
General precautions
Note the following precautions in order to maintain the performance
and reliability of the drive.
! Open the package with particular care.
! Do not expose the unit to excessively dusty environment.
! The unit contains components that can be destroyed by static
electricity.
Follow the guidelines below for internal unit:
! Use an anti-static mat and ground yourself when handling the
internal unit.
! Always be sure to handle the internal unit only by the frame and
do not touch any electrical components.
(2)
Unpacking (Internal Unit)
When moving the unit to an environment where there is a significant
difference in temperature, let the unit remain in its packaging for at least
two hours.
Find a flat, soft surface for unpacking, keeping the box upright.
Do not apply excessive force to the unit when removing the shock-
absorbing material, or to the surfaces and interface connector when
removing the anti-static bag.
(3)
Unpacking (External Unit)
When moving the unit to an environment where there is a significant
difference in temperature, let the unit remain in its packaging for at least
two hours.
Find a flat, soft surface for unpacking, keeping the box upright.
97705183 A
vii
User Manual
(4)
Packing
Pack the unit after you have removed the disk.
Put the device in the anti-static or plastic bag.
It is desirable to use the original shock-absorbing material and packing
box used when the unit was delivered to you. If not, use a box with a
shock-absorbing structure that will prevent direct impacts to the device.
In the case of the internal unit, protect the surfaces and interface
connector against possible damage and use an anti-static bag.
(5)
(6)
Transportation
! Transport the unit in a well-packaged condition, with the upside
facing up.
! Transport the unit as little as possible after unpacking, always
using the shock absorbing material to avoid impact and vibration.
When carrying the unit after unpacking, keep it in the horizontal
plane.
Storage
• Use the moisture-proof packing material for storage.
• The storage environment should meet the non-operating
environmental requirement as specified in Appendix E.
! Do not expose the unit to radical changes in temperature, which
could cause condensation.
97705183 A
viii
User Manual
Table of Contents
Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i
FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Thermal Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Laser Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Class 1 Laser Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Laser Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Unpacking / Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Owners Record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SCSI Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SCSI Identifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Precautions for MOD910E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation & Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Internal Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Prechecks before Service Call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Placing a service call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Service on the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Microsoft Optical Systems and Optical Support . . . . . . . . . . . . . . . . . . . . 11
Disk Cartridge Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Component Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Appendix B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Function Connector Pin Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Appendix C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SCSI Device Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Drive Option Switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Main Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appendix F. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
SCSI Interface connector signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MOD910E SCSI CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MOD910I 50 WAY IDC CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Appendix G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Accessories and Spares . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
97705183 A
1
User Manual
Owners Record
The model and serial number of the drive you have just purchased are
located on the underside of the unit(1). Please record them below, and
refer to them should you need to call your supplier for service or
technical support.
(1)
(External) or the top of the drive (Internal).
(1) (Extern) oder der obere Teil des Laufwerks (Intern).
MOD910 Serial No.
Keep this manual for reference purposes should any switch setting
need to be altered.
Warning
Vorsicht
Use of controls or adjustments other than those specified herein may
result in hazardous laser radiation exposure. This product may only have
the cover removed for service or repair by a qualified and approved
service site.
Anwendung der Kontrollen oder Einstellungen dieses Gerätes anders
wie hier vorgeschrieben, konnen zu schädlicher Strahlenausetzung
fuhren. Das Gehäuse darf nur von einer qualifizierten
Reparaturwerkstatt entfernt werden.
Important
Toutes procédures de vérification, d’alignement ou de tests, autres que
celles spécifiées dans ce manuel, peuvent entraîner une exposition
dangereuse au rayon laser. Dans tous les cas, ce produit ne doit avoir
le capot de protection laser ouvert, que dans les centres de réparation
agréés par le constructeur.
Air Filters
The MOD910E (external drive) is shipped without Air Filters. The drive
has been designed with ducted air cooling, air should not get into the
body of the drive. Air Filters are provided for particularly dusty or dirty
environments. (Please be advised that the drive will run up to a
maximum ambient temperature of 30°C with air filters).
97705183 A
2
User Manual
General Description
The MOD910 is a high performance, high capacity optical disk drive
that offers recording on rewritable and CCW WORM media that is ISO
compliant. The MOD910 reads and writes to 9.1GB, 8.6GB 5.2GB,
4.8GB, 4.1GB, 2.6GB and 2.3GB, rewritable, WORM and DOW disks
and offers read compatibility to earlier ISO standard 1.3GB, 1.2GB,
650MB and 600MB media so protecting any existing investment in
storage.
The MOD910 also forms the basis for the range of Plasmon Magneto
Optical jukeboxes, providing further performance increases. The
MOD910 has been designed to give fast, solid and reliable disk
exchanges .
Please take the time to study this manual to become familiar with
operating the unit, as well as prescribed service.
The main features of the MOD910 drive are:
✓
9.1GB (4.55GB per side) of storage on rewritable, and CCW
WORM disks.
✓
✓
Half height unit.
Reads 594MB and 650MB disks as well as 1.2GB, 1.3GB,
2.3GB, 2.6GB, 4.1GB, 4.8GB and 5.2GB media as used in earlier
MO drives in addition to read & write compatibility to 2.3GB and
2.6GB disks.
✓
✓
✓
✓
Data cache of 8MB for write and read operations.
Effective seek time of 25ms
Synchronous data rates up to 10 MBytes/sec.
Universal AC supply operates from 100 to 240 volts (MOD910E).
97705183 A
3
User Manual
SCSI Connections
The external drive is equipped with two Micro D 50 way connectors on
the rear panel. These are for the SCSI in and SCSI out (if there are
additional devices connected).
A SCSI interface cable needs to be terminated at each end of the line,
one terminator being on the last device in the chain and the other
terminator is usually on the host computer or adapter card, a Micro D
SCSI Terminator is supplied (external drive only).
Refer to the documentation supplied with your SCSI card or computer
system should you need to check the computer termination. In normal
circumstances this will usually be enabled.
The two ways of connecting SCSI devices are shown below :
Fig 1. External Drive Connection
Fig 2. Internal Drive Connection
Fig 1 External Drive Connection
1.Switch block SCSI ID setting
2.SCSI connector for additional devices or terminator if last in chain.
3.SCSI cable
If there are also internal devices on the same SCSI card, then the SCSI
adapter card must have its on-board termination disabled.
97705183 A
4
User Manual
Fig 2 Internal Drive Connection
1. DC Power Connector
2. Jumper block for SCSI ID settings
3. 50 way SCSI cable - note pin 1 orientation
If internal devices are also to be connected to the SCSI card, then the
SCSI adapter on-board termination must be disabled. Refer to the
documentation that accompanies the SCSI adapter.
97705183 A
5
User Manual
SCSI Identifier
Each device on a SCSI bus requires a unique address to be set which
maybe in the range of 0 to 6 as address 7 is usually reserved for the
host computer address. The MOD910 is shipped with a default address
of 1 which will usually suffice in most cases.
Please refer to diagram on Appendix C
General Precautions for MOD910E
✓
Never plug or un-plug any connectors or cables from the
device on the SCSI bus whilst power is applied to either host
computer or any devices attached.
✓
Do not use the unit under the following operating
environments:
Places with high humidity
Exposed to direct sunlight
Locations subject to excessive shock or vibration
✓
✓
✓
✓
✓
✓
Do not cover ventilation slots as these are provided for cooling.
Do not place the drive near a printer.
Never attempt to disassemble the unit.
Never touch the surface of a recordable disk.
Do not allow any foreign object or liquid to enter the unit.
Always remove the disk before moving the unit. This will
ensure that the optical head is securely positioned for shipping.
✓
Keep the packaging material should the unit have to be
transported.
97705183 A
6
User Manual
Additional Notes for Internal Models
✓
Never connect / disconnect unit to / from SCSI bus with
power on any units including host computer.
✓
When handling the unit, an anti-static wrist strap should be
used to avoid possible damage from static electricity.
✓
✓
✓
Ensure that the power connector is correctly wired.
Check that the power is within the unit’s specification.
Ensure that adequate ventilation is provided.
GETTING STARTED
Operation & Installation Instructions
External Drive
Do not apply power yet!
Set the SCSI ID of the unit via the DIP switch on the rear of the unit.
(see Appendix B and C)
Connect the SCSI interface cable between the computer and the drive
unit.
If the drive is the last unit on the SCSI interface, install the supplied
terminator in the unused SCSI connector.
Apply power to the unit.
Insert a disk cartridge into the drive, gently pushing it into the drive until
it is power loaded. The motor will start and after a few seconds the drive
will be ready for use.
When the eject button is pressed the cartridge will electronically eject
from the drive after a short delay.
97705183 A
7
User Manual
Externes Laufwerk
Noch nicht einschalten!
Man stellt die SCSI ID des Geräts am hinterem DIP Schalter ein. (siehe
Anhang B und C).
Verbinden Sie den Rechner und das Laufwerk mit dem SCSI Kabel.
Falls das Laufwerk das letzte Gerät in der SCSI Kette ist, installiert man
den mitgelieferten Begrenzer (Terminator) in den leeren SCSI Sockel.
Schalten Sie das Gerät ein.
Man schiebt eine Disk in das Laufwerk bis das Gerat sie von selber
animmt. Der Motor fängt dann zu laufen an und nach wenigen
Sekunden ist das Laufwerk anwendungsfähig.
Wenn man den Eject-Knopf drückt, wirft das Gerät die Disk nach ein
paar Sekunden wieder aus.
Lecteur Externe
Ne connectez pas encore votre matériel.
Configurez l’adressage SCSI au moyen du "dip switch" en panneau
arrière de l’équipement (voir appendice B et C).
Connectez le câble SCSI entre l’ordinateur et l’unité.
Si l’unité est la dernière de la chaîne SCSI, veillez à installer le
terminateur sur le connecteur SCSI libre.
Alimentez l’unité et mettez la en marche.
Insérez avec précaution une cartouche dans le lecteur jusqu’à la voir
automatiquement "avalée" par l’unité. Le moteur du disque va alors
commencer à tourner et après quelques secondes le lecteur est prêt à
l’utilisation.
Lorsque le bouton "éject" est pressé, la cartouche sera éjectée après
quelques secondes.
97705183 A
8
User Manual
Notes:
If you need to use the emergency eject pinhole, make sure that the unit
is powered off and that the disk has stopped its rotation (20-30 seconds
after power off).
If the SCSI ID is changed with the unit powered ON, then power must
be removed and reapplied for the new ID to take effect.
Before moving the drive, always ensure that the optical disk cartridge is
removed.
The drive has various functions that may be altered from their defaults if
required. These are outlined in the MOD910I section. Opening the
enclosure and changing these settings must only be carried out by a
qualified service engineer.
Internal Drive
! The internal drive can be used in both the vertical and horizontal
plane.
! The external drive must only be used in the horizontal plane.
• Attaching screws are supplied with the unit. The screws are M3 x
8 mm, and the fixing plate should be within the range of 1.5 to
2.5 mm, which includes the washer.
• Included with internal drives is a 50-way flat IDC cable with 2
connectors for connection to the SCSI adapter.
Note for correct orientation of the flat cable when installing!
Pin 1 is usually identified by a red stripe on the edge of the
cable, and connectors have a small arrow by pin 1.
! Connect the internal power connector in your computer to the
drive making sure that the orientation is correct.
97705183 A
9
User Manual
Prechecks before Service Call
1.
?
?
Disk cannot be inserted.
Is power on?
Is the disk orientated correctly?
Is the disk the correct type?
?
2.
?
?
?
?
?
?
Access Failure
Is the cartridge inserted?
Is the SCSI ID set correctly?
Are the SCSI bus terminated correctly?
Is the cartridge set to write protect?
Are other devices on the SCSI bus operating normally?
Is the software device driver installed correctly?
Placing a service call
Contact your supplier or service company. They will probably require
the following information;
Where purchased
Date of Purchase
Serial Number
Description of failure
System information which may include;
?
?
Computer type and SCSI adapter type
Software configuration (in DOS this will be the CONFIG.SYS
and AUTOEXEC.BAT file)
?
Type of device driver being used
Software and Driver Updates
Do you have the latest revisions?
Contact your supplier for firmware or driver updates.
97705183 A
10
User Manual
Service on the unit
There is no prescribed service for the unit. However, to ensure optimum
performance, the unit should operate in as clean an environment as
possible where contaminants do not enter the unit. Should the unit
require cleaning, do NOT attempt to open the drive, but contact your
supplier.
Microsoft Operating Systems and
Optical support
Microsoft have confirmed that their NT operating system versions 3.51
and 4.0 do not currently FULLY support any WORM or Rewritable
Optical media (512, 1024, 2048 or 4096 bytes per sector) or drives
under Fat or NTFS File Systems.
NT, using FAT or NTFS, only supports Optical if the drive and media act
as a Magnetic Hard Drive. (Type 0 Device)
Windows NT will support both WORM and Rewritable Optical media
when used with another File System (such as Plasmon Drive Manager
for NT)
FAT and NTFS with full Optical support are being looked into for a future
release of NT from Microsoft.
Microsoft have committed that Windows 95 will read and write
Rewritable Optical media only when it has been formatted with third
party software. WORM media is not supported and requires third party
software.
UDF 1.02 file formats can be read by Windows 2000 without any
additional driver software, which gives guarantees of future read
compatibility.
Customers using NT with Plasmon Multitasking Manager have no
need for any action.
For details of Optical support in future products from Microsoft, please
contact them direct.
97705183 A
11
User Manual
Disk Cartridge Notes
1.
Never open the shutter to look at the disk. The shutter is
provided for protection against dust, dirt and other
contaminants.
2.
Avoid subjecting the cartridge to sudden shock or impact.
3.
When the write protect window is open, the disk is in a read
only mode of operating.
Read write enable
Write protect
97705183 A
12
User Manual
Appendix A
Component Location
MOD910E
B
A
D
C
A = Busy indicator
B = Power light
C = Cartridge eject
D = Emergency eject
E
A
B
C
D
A = SCSI connectors
B = SCSI ID selector
C = Fan (optional filter)
D = Power connector
E = AC on / off switch
97705183 A
13
User Manual
Appendix A (continued)
Component Location
MOD910I
(Appendix B&C)
97705183 A
14
User Manual
Appendix B
Function Connector Pin Description
(see appendix A for connector location)
Switch Pins
Function
Description
3
2
1
A1 - B1
A2 - B2
A3 - B3
A4 - B4
Parity
SCSI ID 2
SCSI ID 1
SCSI ID 0
Disable SCSI
See Appendix C to set SCSI ID
See Appendix C to set SCSI ID
See Appendix C to set SCSI ID
When the pair of pins is open, the drive
performs SCSI parity checking (default).
Shorting the pins with a jumper forces the
drive NOT to perform the SCSI parity checking.
A5 - B5
A6 - B6
A7 - B7
Disable Write
Cache
When the pair of pins is open, the drive
performs write back caching (default).
Shorting the pins with a jumper forces the
drive NOT to perform the write back caching.
Disable Auto
Spin-up
When the pair of pins is open, the drive
performs an automatic spin-up upon media
loading (default). Shorting the pins with a jumper forces
the drive NOT to perform the automatic spin-up.
Shorting the pair of pins forces the drive to
perform a Write and Verify operation
4
Force Verify
for Write
whenever the host issues a WRITE command
(default). Opening the pins by removing the
jumper will force the drive not to Verify after
Write (unless specified under software
A8 - B8
A9 - B9
Disable Manual
Eject
Shorting the pins disables the eject button
operation. (Default Open).
5
6
Enable Fast SCSI Shorting the pins enables Fast SCSI mode.
Default Closed
Device Type
A10 - B10
When the pins are open the drive responds as
an Optical Memory Device (type 7) (Default).
Shorting the pins forces the drive to respond
as a Direct Access Device (type 0)
A11 - B11
A12 - B12
Enable
Termination
Shorting the pins invokes the internal SCSI
active terminator. With the pins open
(default) Termination is disabled.
These pins supply +5V DC through an isolation
diode for SCSI terminator power to the SCSI
bus TERMPWR line. Shorting the pins enables
SCSI TERMPWR signal (default). Leaving them
open disables.
Terminator
Power
97705183 A
15
User Manual
Appendix C
SCSI Device Address
Jukebox Connector SCSI ID
SCSI Drive
Address
JP1 or SW3
JP2 or SW2
JP3 or SW1
0
1
2
3
4
5
6
7
OFF
OFF
OFF
OFF
ON
ON
ON
ON
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
ON
OFF
OFF
ON
ON
Drives are set up to ID1 as default
Default Jumpers on external and internal units
Jumper/Switch
JP1/SW3
JP2/SW2
JP3/SW1
JP4
internal
N/C
N/C
Fitted
N/C
N/C
N/C
Fitted
N/C
Fitted
N/C
N/C
external
OFF
OFF
ON
N/C
N/C
N/C
ON
N/C
ON
OFF
N/C
Fitted
JP5
JP6
JP7/SW4
JP8
JP9/SW5
JP10/SW6
JP11
JP12
Fitted
97705183 A
16
User Manual
Appendix D
Drive Option Switches
The MOD910 provides eight switches, which permit the user to define certain drive
operations or interface features.
Optional
Switch
Switch
Number
Description
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Reserved
Reserved
Disable Command Eject
Reserved
Enable Library I/F Mode
Reserved
Disable Write Cache
Disable Auto Spin-up
Reserved
Reserved
Reserved
Reserved
Disable SCAM Selection
Reserved
Enable Fast SCSI
Enable Write Cache for Write and Verify Command
S501
S502
Option Switch Function
NOTE:The MOD910I is shipped with the forced verify on write operation
enabled.
NOTE:The drive is shipped with write caching enabled by default. In data critical
applications it may be necessary to disable write caching. This may be achieved using
Adaptecs “SCSI EXPLORER” program under the windows environment. Programmers
may also access this function through the Mode Page Settings.
97705183 A
17
User Manual
Appendix E
Main Specifications
MOD910e
MOD910i
Access times
Average seek (1⁄
Motor start
3
full stroke)
25 ms
2.5 seconds
25 ms
2.5 seconds
Motor stop
Rotational speed
2.2 seconds
3000/3300/3600 RPM
2.2 seconds
3000/3300/3600 RPM
Data transfer rates
User sustained write/read
Burst asynchronous
Burst synchronous
3.07 to 6.14 MB/second
3 MB/second
10 MB/second (Fast SCSI enabled) 10 MB/second (Fast SCSI enabled)
3.07 to 6.14 MB/second
3 MB/second
Buffer size
MTBF (Power On Hours)
8 MB
100,000
8 MB
100,000
Environmental
Operating temperature
Non-operating temperature
Operating humidity
+5 to +40°C
-30 to 60°C
10 to 90%
+5 to +45°C
-30 to 60°C
10 to 90%
Non-operating humidity
Operating vibration (5-350Hz)
Operating shock (no damage)
Non-operating shock
5 to 90% non condensing
5 to 90% non condensing
0.00015 G Hz or 0.014 m2/s3
2
2
0.00015 G Hz or 0.014 m2/s3
30G or 294 m/s2, 3ms half sine
89G or 873 m/s2, 3ms half sine
30G or 294 m/s2, 3ms half sine
89G or 873 m/s2, 3ms half sine
Electrical
Operating voltage
Power requirements
100 to 240V AC; 50/60Hz
0.5A
+5V ± 5%; 12V + 5%
+5V @ 2.0A (Max); 0.8A (Typ)
12V @ 3.0A (Max); 0.9A (Typ)
Structure
Dimensions (WxHxD in mm)
Weight
228 x 66 x 276
3.9 Kg
146 x 41.3 x 203
1.5 Kg
Drive orientation
Warranty
horizontal
one year parts and labour
return to base
horizontal/vertical
one year parts and labour
return to base
97705183 A
18
User Manual
Appendix F
SCSI Interface connector signal names
MOD910E SCSI CONNECTOR
SIGNAL NAME
DB0
PIN NUMBER
SIGNAL SOURCE
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST / CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DBP
GROUND
GROUND
GROUND
TERMPWR
GROUND
GROUND
ATTN
SCSI HOST /CONTROLLER
SCSI HOST
GROUND
BSY
SCSI HOST /CONTROLLER
SCSI HOST
ACK
RST
SCSI HOST
MSG
CONTROLLER
SEL
SCSI HOST /CONTROLLER
CONTROLLER
C / D
REQ
CONTROLLER
I / O
CONTROLLER
97705183 A
19
User Manual
SCSI Interface connector signal names
MOD910I 50 WAY IDC CONNECTOR
SIGNAL NAME
DB0
PIN NUMBER
SIGNAL SOURCE
2
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
SCSI HOST /CONTROLLER
DB1
4
DB2
6
DB3
8
DB4
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
DB5
DB6
DB7
DBP
GROUND
GROUND
GROUND
TERMWR
GROUND
GROUND
ATTN
SCSI HOST /CONTROLLER
SCSI HOST
GROUND
BSY
SCSI HOST /CONTROLLER
SCSI HOST
ACK
RST
SCSI HOST
MSG
CONTROLLER
SEL
SCSI HOST /CONTROLLER
CONTROLLER
C / D
REQ
CONTROLLER
I / O
CONTROLLER
97705183 A
20
User Manual
Appendix G
Accessories
Media
P9100W 9.1GB WORM MO media (4096 bytes/sector)
P9100E 9.1GB Rewritable MO media (4096 bytes/sector)
P8600W 8.6GB WORM MO media (2048 bytes/sector)
P8600E 8.6GB Rewritable MO media (2048 bytes/sector)
Filter Pack kit
Part No.
Contains:
RS-184-5113
5 x Replacement Filters (external drive only)
97705183 A
21
Contacting Plasmon
Should there be a need for further support other than what this
manual provides, please contact one of these two technical
support locations:
To obtain technical support in the United States
Plasmon
1-877-585-6793
Technical Support
1-719-593-4192 (fax)
e-mail
World Wide Web
To obtain technical support in Europe
Plasmon Technical Support
+44 (0) 1763 262 963
+44 (0) 1763 264 444
e-mail
World Wide Web
International Calls
1-719-593-4437
1-719-593-4192 (fax)
European Headquarters
Plasmon Data Limited
Whiting Way
Melbourn
Hertfordshire SG8 6EN
Tel +44 (0)1763 262963
Fax +44 (0)1763 264444
Email: [email protected]
United States
Plasmon
4425 ArrowsWest Drive
Colorado Springs CO, 80907-3489
Tel (719) 593-7900
Fax (719) 599-8713
|