HD7832, HD7830
Coffee Machine
ENGlISh
3
17. To prevent scalds and/or property damage, always make sure
Coffee Machine lid is securely in place and properly locked before
you start using the machine and during brew cycle.
Do not force when opening or closing lid.
18. Do not open lid until Coffee Machine has finished brew cycle.
Hot steam or hot water trapped under lid cover could burn your
fingers.
19. Warning:To reduce the risk of fire or electric shock,
do not remove the bottom cover. No user serviceable
parts are inside. Return the Coffee Machine to the
Philips Norelco Service location for examination,
repair or adjustment.
SAVEThESE
INSTRUCTIONS
SPECIAl INSTRUCTIONS
This Coffee Machine has a short cord to reduce the hazards of
becoming entangled in or tripping over a longer cord.An extension
cord may be used if the rating is equal to or greater than the rating
of the Coffee Machine. Use an extension cord rated 13 amperes
or greater. Care must be taken to arrange extension cord so that it
does not hang over the edge of counter top or table top, where it
can be pulled on by children or tripped over unintentionally.
Operating the Coffee Machine and another appliance at the same
time from the same electrical circuit could cause an electrical
overload, which would blow the fuse or trip the circuit breaker.
SPECIAl POlARIZED PlUG
INSTRUCTIONS
This Philips Coffee Machine has a polarized plug (one blade is wider
than the other) as an added safety feature.To reduce the risk of
electric shock:
- Plug will fit into polarized outlet only one way.
- If plug does not properly fit into outlet at first, reverse it.
- If plug still does not fit, contact a qualified electrician.
DO NOT ATTEMPTTO DEFEATThIS
SAFETY FEATURE IN ANYWAY.
ꢀ
ENGlISh
WARNING:
-To avoid risk of personal injury or damage to property as a result
of overflow, be sure that the cup or mug is centered under the
coffee outflow unit during the brew cycle.
- Brewed coffee and coffee pods are very hot. Handle with care to
avoid scalding.
- If coffee coffee spout overflows or fails to drain into cup/mug
during brewing cycle, do not open lid or handle coffee spout
or coffee pod holder(s). Unplug Coffee Machine and wait for
contents to cool before handling.
- Do not remove any part of Coffee Machine or cup/mug during
the brew cycle as scalding could occur.
- Use only fresh, cool water in this appliance. Do not put any other
liquids in this appliance except as instructed in the ‘Descaling’
section. Do not refill the water reservoir with hot water or coffee.
- DO NOT attempt to move an appliance containing hot liquids or
during the brewing process.Allow appliance to cool completely
before moving.
- Keep appliance at least 4 inches away from walls or other objects
while operating. Do not place any object on top of coffee
machine while operating.
PlEASE READ AND SAVEThIS
INSTRUCTION BOOKlET.
TABlE OF CONTENTS
General description
Introduction
6
7
Preparing the machine for use
Brewing coffee
Cleaning
7
9
13
16
17
17
18
23
Descaling
Storage
Assistance
Troubleshooting
Warranty
6
1
h
I
A
B
J
F
G
K
l
C
M
D
N
E
O
P
Q
R
General description (Fig. 1)
A Display
1 Heat-up indication
2 Coffee volume indication
3 Water refill indication
4 Descaling indication
B Volume select button
C Outflow valve
D Water reservoir
E Grip area
F Sealing ring
G Water distribution disc
H 1-cup pod holder q
I 2-cup pod holder qq
J Cover of coffee spout
K Coffee spout
L Coffee collector
M Cup tray
N Drip tray
O 1-cup button q
P Water level light rings
Q On/off button with indicator light
R 2-cup button qq/w
7
Introduction
\
With Douwe Egberts SENSEO coffee pods, you can enjoy a perfect cup
of coffee at any time of the day. Every cup is freshly brewed to give you
that smooth and full taste.
Using more than 250 years of coffee expertise, Douwe Egberts has
roasted and ground specially selected coffee beans that, when prepared
using a special brewing method co-developed with Philips, ensure a full,
smooth taste and delicious foam layer.This joint creation, known as the
\
\
SENSEO coffee pod system, consists of the Philips SENSEO coffee
\
machine and specially developed Douwe Egberts SENSEO coffee pods.
Only when used together will you be rewarded with a sensational cup of
\
\
SENSEO coffee with the delicious SENSEO foam layer.
To ensure a smooth and full coffee taste, you should keep the following
things in mind:
Fresh water
Use fresh water every day. If you have not used the coffee machine for
three days, you have to flush it with fresh water before you use it again
(see section ‘Flushing’ in chapter ‘Cleaning’).
Fresh coffee pods
\
Use the SENSEO coffee pods that have been specially developed by
\
Douwe Egberts for your SENSEO coffee machine for a full, round taste.
\
The Douwe Egberts SENSEO coffee pods will stay fresh longer if you
store them in an airtight storage container.
A clean machine
\
Clean and descale your Philips SENSEO coffee machine regularly (see
chapters ‘Cleaning’ and ‘Descaling’). Remove used coffee pods after brewing.
If a used pod has been left in the coffee machine and you have not used
the machine for some time, flush the machine before you use it again (see
section ‘Flushing’ in chapter ‘Cleaning’).
Preparing the machine for use
\
USETHIS SENSEO COFFEE MACHINE FOR ITS INTENDED
HOUSEHOLD USE AS DESCRIBED INTHIS MANUAL.
YOU CANNOT BREW COFFEE IFYOU HAVE NOT FLUSHEDTHE
\
SENSEO COFFEE MACHINE FIRST! Note that the display will not
work until you have flushed the machine.
The flushing cycle causes the boiler to be filled with water.After this the
coffee machine is ready for use.
Flush the machine in the following way:
1 Remove the water reservoir.
8
2 Fill the water reservoir with cold water up to the MAX indication
and put it back onto the machine.
3 Release the lid by moving the lever upwards.
ꢀ Open the lid.
5 Put the 1-cup pod holder qor the 2-cup pod holder qqin the
machine without pod(s).
6 Close the lid and lock the lever.
Note: Make sure the lever is properly locked by pushing it down until it snaps
home with a click.
Note: Never flush the machine with the lid open.The lid must be properly
locked.
7 Put the plug into a grounded 120V AC electrical outlet.
9
8 Put a bowl (with a capacity of at least 1.6 qt./ 1.5 litres) under the
spout openings to collect the water. )
9 Press the on/off button 3.
After pressing the on/off button 3, the display lights up for a moment and
the light rings around the 1-cup button qand the 2-cup button qq/w
burn continuously.
10 Press the 1-cup button qAND the 2-cup button qq/wbriefly at
the same time.
,
The boiler fills itself with water from the water reservoir.This may
take some time (approx. 90 to 150 seconds).The machine switches
off automatically when the flushing cycle ends. During the flushing
cycle the machine produces more noise than during a regular
brewing cycle.
Never interrupt the flushing cycle halfway. If you do, the boiler will not
fill itself properly.
Note: Before you use the machine for the first time, clean the coffee spout, the
coffee collector and the pod holders with hot water and some dish soap or in
the dishwasher. Clean the water reservoir thoroughly in hot water, if necessary
with some dish soap.
\
Now your Philips SENSEO coffee machine is ready for use.
Brewing coffee
1 Fill the water reservoir with cold water up to the MAX indication
and put it back onto the machine.
Never pour milk, coffee, hot water or carbonated water into the water
reservoir.
- qMIN: minimum amount of water required to brew one cup of
\
SENSEO coffee.
- qq/wMIN: minimum amount of water required to brew 2 cups or
\
1 mug of SENSEO coffee.
A full reservoir allows you to make 6 large cups h, 8 medium cups g
or 10 small cups fof SENSEO coffee.This makes it unnecessary to
-
\
fill the water reservoir each time you want to make a cup of coffee.
10
2 Press the on/off button 3.
,
The indicator light blinks slowly and the display shows the heat-up
indication Dwhile the water is heating up. Heating up takes approx.
90 seconds.
The coffee machine is ready for use when the indicator light burns
continuously and the light rings around the 1- cup button qand the
2-cup button qq/wgo on.
,
,
,
If the indicator light blinks rapidly and the display shows the water
refill indication s, the water reservoir does not contain enough
water for brewing one cup of coffee.
If there is not enough water for brewing two cups of coffee, the light
ring around the 2-cup button qq/wwill not go on and this button
cannot be operated.
3 Release the lid by moving the lever upwards.
ꢀ Open the lid.
5 Place the appropriate pod holder in the machine.
Note: Make sure the pod holder is clean and the sieve in the centre is not
clogged, e.g. with loose coffee grounds.
\
,
If you want to make one cup of SENSEO coffee, use 1 coffee pod in
combination with the 1-cup pod holder qand the 1-cup button q.
,
11
,
If you want to make two cups of SENSEO\ coffee, use 2 coffee pods
in combination with the deeper 2-cup pod holder qqand the 2-cup
button qq/w.
\
6 Place the SENSEO coffee pod(s) properly in the center of the pod
\
holder, with the flat SENSEO side up and the rounded side facing
down.
\
Note: Use SENSEO coffee pods from Douwe Egberts specially designed for
\
your SENSEO coffee machine for a full and round taste.
Note:Make sure the coffee in the pod(s) is evenly distributed and press the
pod(s) lightly into the pod holder.
\
Note: Never put normal ground coffee or use torn pods in the SENSEO
machine, as this will cause it to become blocked.
,
Place 1 SENSEO\ coffee pod in the 1-cup pod holder q
or,
\
,
place 2 SENSEO coffee pods in the 2-cup pod holder qq.
7 Close the lid and lock the lever.
Always check if the lid is properly locked.The lever must be pushed down
until it snaps home with a click.
Never start brewing with the lid open.The lid must be properly closed.
8 Place one cup or two cups under the spout openings.You can adjust
the height of the coffee spout by sliding it upwards or downwards.
The cups you use should have a capacity of at least 4 oz. when you brew
small cups f, 5 oz. when you brew medium cups gand 6 oz. when you
\
brew large cups hof SENSEO coffee. Do not use cups that are too large,
as they will cause the coffee to get cold more quickly.
9 Select the desired coffee volume by pressing the volume select
button j. By varying the volume, you will also affect the strength of
the coffee.
12
,
Select 1 bar for a 3 oz. cup or a 6 oz. mug of coffee.
,
Select 2 bars for a ꢀ oz. cup or a 8 oz. mug of coffee.
,
Select 3 bars for a 5 oz. cup or a 10 oz. mug of coffee.
\
10 Press the button indicating the number of cups of SENSEO coffee
you want to brew.
-
-
Press the 1-cup button qfor one cup.
Press the 2-cup button qq/wfor two cups or one mug.
The light rings around the 1-cup button qand the 2-cup button qq/w
indicate if there is still enough water left for brewing one or two cups of
coffee. If there is not enough water left in the water reservoir for brewing
two cups of coffee, the light ring around the 2-cup button qq/wwill not
go on and this button cannot be operated.
\
,
The SENSEO coffee machine starts brewing.
-
-
The machine automatically supplies the selected amount of water.
You can interrupt the brewing process at any time by pressing the
on/off button 3. If you switch the machine back on after having
interrupted the brewing process, the machine will not complete the
interrupted brewing cycle.
Do not remove the water reservoir during a brewing cycle, as this will
cause the machine to draw in air.When this happens, the next cup will
only be partly filled.
Note: If you only get a small quantity of coffee or no coffee at all out of the
13
machine, you have not flushed the machine properly before first use.As a
result, the boiler is not or not completely filled. Flush the machine properly (see
chapter ‘Preparing the machine for use’) before you brew another cup of coffee.
11 Remove the coffee pod(s) after use by lifting the pod holder out of
the machine and emptying it.
Be careful when doing this, for there may still be some hot water/coffee on
the coffee pod(s) or steam may escape.
Tips
,
By rinsing the pod holders, the coffee collector and the coffee spout
regularly, you will make sure that the coffee always tastes optimally.
\
,
,
The SENSEO coffee will taste best if you stir it before drinking it.
\
If you intend to make another cup of SENSEO coffee later, just
leave the coffee machine switched on.The machine will automatically
switch itself off after 1 hour.
Cleaning
\
Never immerse the SENSEO coffee machine in water or any other liquid.
Never clean the machine by flushing it with the lid open.
1 Always turn machine Off and unplug before cleaning it.
2 Clean the outside of the machine with a moist cloth.
3 Remove the coffee collector.
ꢀ Take the coffee spout out of the machine by sliding it upwards.
The coffee spout can only be taken out after the coffee collector has been
removed.
,
You can disassemble the coffee spout for more thorough cleaning!
1ꢀ
5 Clean the coffee spout, the coffee collector and the drip tray in hot
water, if necessary with some dish soap, or in the dishwasher.
6 Hold the cup tray in your hand while cleaning it with hot water, if
necessary with some dish soap.
The cup tray can also be cleaned in the dishwasher.
To clean the cup tray, always remove it from the machine, as it might
prove sharp when handled incorrectly.Always handle it carefully.
7 Clean the pod holders in hot water, if necessary with some dish soap,
or in the dishwasher.
Check if the sieve in the centre of the pod holder is clogged. If this is the
case, unclog the sieve by rinsing the pod holder under a running tap.
Use a soft dish brush to clean the sieve, if necessary.
8 Clean the water reservoir in hot water, if necessary with some dish
soap.
Note: If you are using a soft dish brush, be careful not to damage the valve in
the bottom of the water reservoir.
9 Do not use an object with sharp edges to clean the water inlet on
the machine.
10 Rinse the parts with fresh water after cleaning and put them back
into the machine.
15
11 Clean the water distribution disc with a moist cloth.
Be careful when you do this; make sure that the rubber sealing ring does
not get stuck under the edge of the water distribution disc. If it does, the
coffee machine will start leaking!
Flushing
If you have not used the coffee machine for three days, you have to flush it
with fresh water before you use it again.
Flush the machine in the following way:
1 Fill the water reservoir with cold water up to the MAX indication
and put it back into the machine.
2 Put the 1-cup pod holder qor the 2-cup pod holder qqin the
machine without pod(s).
3 Close the lid and lock the lever.
ꢀ Put a bowl (with a capacity of at least 1.6 qt./1.5 litres) under the
coffee spout to collect the water.
5 Press on/off button 3(1) and subsequently press the 1-cup button
qand the 2-cup button qq/wbriefly at the same time (2).
The machine fills itself with water from the water reservoir.While
this happens, water comes out of the spout.When the flushing cycle is
finished, the machine switches itself off. During the flushing cycle, the
machine produces more noise than during a regular brewing cycle
Never interrupt the flushing cycle halfway. If you do, the boiler will not fill
itself properly. Repeat step 5 if the cycle is interrupted.
16
Descaling
Regular descaling will prolong the life of the coffee machine and will
guarantee optimal brewing results for a long time.
,
When you need to descale the machine, the descaling indication
bappears on the display.This happens after 500 cups
have been brewed.After another 8 cups, the descaling indication
bdisappears from the display (whether or not you have
performed the descaling procedure).
1 Fill the water reservoir up to the MAX indication with white
vinegar or with a mixture of descaler and water according to the
instructions on the package of the descaler.Then put the water
reservoir back into the coffee machine.
Use a liquid descaler based on citric acid.
2 Press the on/off button 3.
The machine is ready for use when the indicator light burns continuously.
3 Place the 1-cup pod holder qin the coffee machine, preferably with
a used coffee pod in it. Close the lid and make sure it is properly
locked.
We advise you to put a used coffee pod in the pod holder when you
descale the machine.This pod will serve as a ‘filter’ to prevent the sieve in
the pod holder from getting clogged with scale residues.
ꢀ Put a bowl with a capacity of at least 1.6 qt./1.5 litres under the
spout openings to collect the vinegar or the mixture of descaler and
water.
5 Press the 2-cup button qq/wfor 2 cups and let the machine
operate. Repeat this until the water reservoir is empty.
\
Never descale the SENSEO coffee machine with the lid open.
Make sure the lid is properly locked.
6 Repeat steps 1 to 5 with new vinegar or a new mixture of descaler
and water.
17
7 Empty the water reservoir to remove the last vinegar or mixture of
descaler and water.
8 Rinse the machine at least 3 times by repeating steps 1 to 5, now
using fresh water.
,
,
Do not refill the water reservoir with used hot water.
Discard hot water each tme.
9 Discard the used coffee pod and clean the pod holder after descaling
to prevent the sieve in the center from getting clogged.
This coffee machine has no other user-serviceable parts.Any other service
should be performed by the Philips Norelco Service location.
Storage
If the coffee machine has already been used and therefore has been
flushed with water, it may only be used and stored in a frost-free place to
prevent it from becoming damaged. Empty water resorvoir before storing.
Assistance
For assistance, call toll free: 1-866-473-6736 or visit our website:
Information is available 24 hours a day, 7 days a week.
18
Troubleshooting
If you have a problem, you may find the solution in the table below. If
the table does not provide the solution to your problem or if you have a
question, see chapter ‘Assistance’.
Problem
Solution
The indicator light continues You have not yet flushed the coffee machine (see chapter ‘Preparing the
to blink slowly. machine for use’).
\
You have used the SENSEO coffee machine at an altitude higher than
6800 Ft. / 2200 m above sea level.This has caused the water in the
machine to start boiling before it has reached the required temperature,
which prevents the machine from functioning properly. Switch the machine
off and no longer use it at altitudes higher than 6800 Ft. / 2200 m above
sea level.
\
The SENSEO coffee
machine does not produce
coffee when used for the
first time.
You have not yet flushed the coffee machine.When you use the machine
for the first time, you have to flush it before you can start brewing coffee
(see chapter ‘Preparing for use’).
The display doesn’t work
when the machine is
switched on for the first
time.
You have not yet flushed the coffee machine.The display starts working
after the machine has been flushed (see chapter ‘Preparing for use’).
The indicator light continues Make sure that:
to blink rapidly.
the water reservoir has been properly placed;
there is enough water in the water reservoir (i.e. above the qMIN level
if you want to brew 1 cup);
the ambient temperature is not lower than 50cF / 10cC. If it is, the
machine will not function properly.
The 2-cup button
Make sure that there is enough water in the water reservoir for brewing
qq/wcannot be operated. 2 cups of coffee. If the light ring around the 2-cup button qq/wis out,
there is not enough water in the water reservoir for brewing 2 cups.
Water leaks from the coffee Make sure that:
machine.
the lid is properly closed (the lever must be properly locked);
the water reservoir has not been filled beyond the MAX level;
the sieve in the centre of the pod holder is not clogged. If it is, unclog the
sieve by holding the pod holder under a running tap. If necessary, you can
use a soft dish brush or a pin to unclog the sieve;
the coffee pod has been put properly in the centre of the pod holder;
the sealing ring is not stuck under the edge of the water distribution disc.
19
Problem
Solution
the water drops on the worktop are not the result of placing or
removing the water reservoir or removing used coffee pods;
you do not remove the water reservoir when the coffee machine is
heating up.This may cause water that normally ends up in the water
reservoir to leak out of the machine.
In all other cases, contact the Philips Norelco Service Location.
The coffee spout cannot be The coffee spout can only be taken out after the coffee collector has
taken out of the machine.
been removed.
The lid cannot be opened.
A vacuum may have temporarily formed under the lid.
Switch the machine off. Pull the lever up as far as it will go and wait
24 hours before opening the lid.You may need to use quite some force.
Make sure that the sieve in the centre of the pod holder is not clogged.
If it is, unclog the sieve by holding the pod holder under a running tap. If
necessary, you can use a washing-up brush or a pin to unclog the sieve.
If problems continue to occur, contact the Philips Norelco Service
Location.
The coffee machine
produces less coffee than
before.
Perhaps the sieve in the centre of the pod holder is clogged. If this is the
case, unclog the sieve by rinsing the pod holder under a running tap. Use
a soft dish brush to clean the sieve, if necessary.
Descale the machine (see chapter ‘Descaling’).
The Senseo coffee machine
brews only a small quantity
of coffee or no coffee at all
when it is used for the first
time.
You have not flushed the machine properly before first use.As a result,
the boiler is not or not completely filled. Flush the machine properly (see
chapter ‘Preparing the machine for use’) before you brew another cup
of coffee.
The lid cannot be closed
properly.
Check if a used coffee pod is sticking to the water distribution disc. If this
is the case, remove the used pod.
Check if you used the correct pod holder. Use 2 pods in combination
with the deeper 2-cup pod holder qq. Use 1 pod in combination with
the 1-cup pod holder q.
The machine has been
stored in a room that was
not frost-free.
Contact the Philips Norelco Service Location.
Make sure that:
\
The SENSEO coffee is not
strong enough.
you have used the correct number of pods and have pressed the right
button. Use 1 pod in combination with the 1-cup pod holder qand the
1- cup button q. Use 2 pods in combination with the 2-cup pod holder
qqand the 2-cup button qq/w.
20
Problem
Solution
the coffee pod(s) have been placed properly in the centre of the pod
holder, to prevent water from escaping along the edge of the pod(s).
When you are using two coffee pods on top of each other, make sure
\
that the flat SENSEO sides of both pods are facing up and press the
pods lightly into the pod holder;
you have not used the same pod twice by accident;
the coffee in the pod is evenly distributed;
\
If you prefer a more robust flavour, SENSEO coffee pods with a
stronger blend are available.
\
\
The SENSEO coffee is too If you prefer a milder flavour, SENSEO coffee pods with a milder blend
strong.
are available.
The coffee is not hot
enough.
Do not use cups that are too large, as they will cause the coffee to get
cold more quickly. Make sure the cups have a capacity of at least 4 oz.
when you brew small cups f, 5 oz. when you brew medium cups gand
\
6 oz. when you brew large cups h of SENSEO coffee.
The preferred coffee volume Make sure that there is enough water in the water reservoir.
cannot be selected.
The coffee volume indication Make sure that there is enough water in the water reservoir.
does not appear on the
display and it is not possible
to select a volume.
21
22
23
FUllTWOYEARSWARRANTY
Philips Electronics North America Corporation warrants each new Philips Product, model
HD7832/7830 (except cord, coffee pods and accessories) against defects in materials or workmanship
for a period of two years from the date of purchase, and agrees to repair or replace any defective
product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack
of reasonable care, the affixing of any attachment not provided with the product or loss of parts or
subjecting the product to any but the specified voltage.
* Use of unauthorized replacement parts will void this warranty.
PhIlIPS ElECTRONICS NORTh AMERICA CORPORATIONWIll NOT PAY FOR
WARRANTY SERVICE PERFORMED BY A NON-AUThORIZED REPAIR SERVICE
ANDWIll NOT REIMBURSEThE CONSUMER FOR DAMAGE RESUlTING FROM
WARRANTY SERVICE PERFORMED BY A NON-AUThORIZED REPAIR SERVICE.
NO RESPONSIBIlITY IS ASSUMED FOR ANY SPECIAl, INCIDENTAl, OR
CONSEQUENTIAl DAMAGES.
In order to obtain warranty service, simply ship the product postage prepaid to the Philips Norelco
suggested that for your protection, you return shipments of product by insured mail, insurance prepaid.
Damage occurring during shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.This warranty gives you specific legal rights, and you may also have other rights that vary
from state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Domestic Appliances and Personal Care Company
A Division of Philips Electronics North America Corporation
1010Washington Blvd., Stamford, CT 06912-0015
This symbol on the product’s nameplate means it is listed by Underwriters
Laboratories, Inc.
PHILIPS and Philips Shield are RegisteredTrademarks of Koninklijke Philips Electronics N.V.
Senseo is aTrademark of Koninklijke Philips Electronics N.V. when used for coffee makers.
Senseo is aTrademark of Sara Lee/NE N.V. when used for coffee pods.
Design and quality by Philips and Sara Lee Douwe Egberts.
2006 Philips Electronics North America Corporation.All Rights Reserved.
ꢀ222.200.0008.1
|