Important safety instructions
Warning
• Make sure the baby unit and the cord are always
out of reach of the baby (at least 1 metre/3 feet
away).
• Keep the parent unit at least 1.5 metres/5 feet away
from the baby unit to prevent acoustic feedback.
• Never place the baby unit inside the baby’s bed or
playpen.
• The Electrical network is classified as hazardous.The
only way to power down the charger is to unplug
the power supply from the electrical outlet. Ensure
that the electrical outlet is always easily accessible.
• Refer to safety information before using the
product.
• Never cover the parent unit and the baby unit with
anything (e.g. a towel or blanket).Always make sure
the cooling vents of the baby unit are free.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• If you place the parent unit next to a transmitter
or other DECT appliance (e.g. a DECT telephone
or wireless router for the internet), the connection
with the baby unit may be lost. Move the baby
monitor further away from the other wireless
appliances until the connection is restored.
• This baby monitor is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
• This product complies with European R&TTE
directive 1999/5/EC
• Use only the power supply listed in the user
instructions.
• Use only the batteries listed in the user instructions.
• Do not allow the product to come into contact
with liquids.
• Risk of explosion if battery is replaced by an
incorrect type.
• Dispose of used batteries according to the
instructions.
• When the handset rings or when the handsfree is
activated, keep the handset away from your ear to
avoid hearing damage.
When using the phone as a baby monitor
• Children should be supervised to ensure that they
do not play with the appliance.
Overview
1
Loudspeaker
(back side)
Earpiece
In call
Standby
Display icons
Display icons
The number of bars indicates the connection
/
/
Enter the option menu.
Access the main menu.
The speaker is on.
OK
OK
status between the handset and base station.
The more bars are shown, the better the signal
strength is.
Change the sound profile.
Adjust the volume.
Access the redial list.
Phonebook
The ringer is off.
The silent mode is set and within active period
(the phone does not ring).
Recall (network dependent).
End calls.
Call log
It remains steadily on beside the unread missed
call record when browsing the call log.
Answering machine: it flashes when there is a
new message. It displays when the telephone
answering machine is turned on.
Make and receive calls.
OK
It flashes when there is a new missed call. It
remains steadily on when browsing missed calls
in call log.
Turn the speaker on/off.
Mute/unmute the microphone.
Enter a pause (press and hold).
Make intercom call (press and hold).
Multi-handset version only.
Voice messages indicator: flashes for new
messages, is steady for reviewed messages.
*This is network dependent
Lock/unlock the keypad (press and hold).
Make and receive calls through the speaker.
The alarm is activated.
Microphone
The silent mode is set, but is outside of active
period.
ECO The ECO mode is activated.
Find handset (back side)
ECO+ The ECO+ mode is activated.
In menu
In text input
Delete a character.
/
Confirm / Select / Enter the option menu.
OK
Delete all characters (press and hold).
Cancel
Enter a space.
Up / down
Exit menu.
Main menu icons
Alarm
Switch upper/lower case (press and hold).
Left / right
Phonebook
Services
Baby monitor
Sounds
Phone setup
Answer machine
Display
Get started
3
Configure your phone
Charge your phone
1 The batteries are pre-installed in the handset. Pull the
battery tape off from the battery door before charging.
2 When using your phone for the first time, you see a
welcome message (country dependent).
3 Set the country and language if prompted.
4 Set the date and time.
Charge 8 hours
/
• If the time is in 12-hour format, press
to
select [am] or [pm] (country dependent).
Charge your handset by docking it in either direction.The
LED at the back of the handset flashes once.
> 84%
36% - 52%
18% - 36%
< 18%
68% - 84%
52% - 68%
Flashing: low battery
Enjoy
4
Listen to the incoming messages
Phonebook
Call log
Redial list
Select [Menu] >
> [Play], then press [OK] to
Add record
1 Press > [Option] > [Add new].
2 Follow on-screen instructions.
Call from the call log
Call from the redial list
confirm.
1 Press
> [Incoming calls].
1 Press [Redial].
2 Select a record and press
Delete an incoming message
2 Select a record and press
.
.
1 When you listen to the message, press [Option]
to enter the options menu.
2 Select [Delete], then press [OK] to confirm.
Call from the phonebook
View record
Save record
1 Press [Redial].
2 Select a record and select [Option] >
[Save number].
3 Follow on-screen instructions.
1 Press
.
1 Press
> [Incoming calls].
2 Select a record and press
.
2 Select a record and select [Option] > [View].
Register additional handsets
Direct access memory
Save record
You can register additional handsets to the base station.
You have 9 direct access memories (Keys 1 to 9).To
dial the saved phone number automatically, press and
hold on the keys in standby mode.
Depending on your country, keys 1 and 2 are
preset to the voice mail number and information
service number of your service provider respectively
(network dependent).
1 Press
> [Incoming calls].
1 Select [Menu].
Delete record
1 Press [Redial].
2 Select a record and select [Option] > [Delete].
3 Follow on-screen instructions.
2 Select a record and select [Option] >
[Save number].
3 Follow on-screen instructions.
/
2 Press
to select
> [Register].
3 Press and hold on the base station for 5 seconds.
4 Enter the system PIN/passcode (0000).
Delete record
5 Press [OK] to confirm the PIN/passcode.
1 Press
> [Incoming calls].
Telephone answering machine
Record an announcement
1 Press [Menu].
»
Registration is complete in less than 2 minutes.
2 Select a record and select [Option] > [Delete].
3 Follow on-screen instructions.
/
2 Press
to select
> [Announcement].
3 Follow on-screen instructions.
Learn more
5
Silent mode
Sets time during which the phone will not ring
> [Silent mode]
MySound
Customizes the sound of voices to your liking
> [MySound]
Eco mode
Reduces power consumption / transmission power;
reduces radiation and range by approximately 60%
> [Eco mode]
Eco+ mode
Eliminates radiation in standby mode (causes 2
seconds ring delay, 50% shorter standby time)
> [ECO+ mode]
Call barring
Prevents unwanted outgoing calls to selected
numbers
> [Call barring]
Technical data
Battery
• Philips: 2 x AAA NiMH 1.2V Rechargeable
550 mAh batteries
Use only the supplied batteries.
Adapter
• MEIC: MN-A075-U056
Input: 100-240V~ 50/60 Hz 200 mA;
Output: (i)6.5V 300 mA, (ii)7.5V 200 mA
Phonebook with 250 entries
Call log with 50 entries
Talk time: 18 hours
Standby time: 250 hours
Note
• You can install a DSL (digital subscriber line) filter to
prevent noise and caller ID problems caused by the
DSL interference.
• You can find the Declaration of Conformity on
Frequently asked questions
No signal bar is displayed on the screen.
I have chosen a wrong language which I cannot
read, what do I do?
No display
Bad audio (crackles, echo, etc.)
• The handset is nearly out of range. Move it closer
to the base station.
• The phone receives interference from the nearby
electrical appliances. Move the base station away
from them.
• The phone is at a location with thick walls. Move
the base away from them.
• The handset is out of range. Move it closer to the
base station.
• If the handset displays
[Register your Handset], register your
handset. (See the section on “Register additional
handsets”).
• Make sure the batteries are charged.
• Make sure there are power and phone
connections.
1 Press
2 Press
3 Press
to go back to the standby screen.
to access the main menu screen.
to select , then you see one of
/
The handset on the charger does not charge.
the following texts appear on the screen:
• Make sure the batteries are inserted correctly.
• Make sure the handset is placed properly on the
charger.The LED at the back of the handset flashes
once.
• Make sure the docking tone setting is turned on.
When the handset is placed correctly on the
charger, you can hear a docking tone.
• The charging contacts are dirty. Disconnect the
power supply first and clean the contacts with a
damp cloth.
[Language]
[Sprache]
[Langue]
[Lingua]
If I fail to pair (register) the additional handsets to
the base station, what do I do?
The handset does not ring.
Make sure the handset ringtone is turned on.
The caller ID does not display.
• The service is not activated. Check with your
service provider.
• The caller’s information is withheld or unavailable.
4 Select it to access the language options.
5 Select your own language.
Your base memory is full. Press
to select > [Unregister] to unregister the
unused handsets and try again.
.Then press
/
My handset is in searching status, what do I do?
• Make sure that the base station has power supply.
• Register the handset to the base station.
• Move the handset closer to the base station.
• Batteries are defective. Purchase new ones with
the same specifications.
I cannot change the settings of my voice mail, what
do I do?
The voice mail service is managed by your service
provider but not the phone itself. Contact your
service provider to change the settings.
0168
When this crossed-out wheeled bin symbol is
attached to a product it means that the product is
covered by the European Directive 2002/96/ EC.
Reproduction in whole or in part is prohibited
without the written consent of the copyright owner.
Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners.
All rights reserved.
UMS_M888
05_EN_V1.0
WK13285
© 2013 Koninklijke Philips Electronics N.V.
|