CR-L5_E.book Page 1 Monday, May 19, 2003 4:05 PM
Contents
Introduction
Important Safeguards ....................................2
Precautions ....................................................4
Features .........................................................5
Supplied Accessories ....................................6
Disc Notes .....................................................6
Before Using the CR-L5 ...............................7
Controls & Connectors..................................8
CD Receiver
CR-L5
Instruction Manual
Connections
Connecting Your Other Components to the
CR-L5 ......................................................11
Connecting
-compatible Components ...12
Connecting Your Speakers..........................13
Connecting Antenna....................................14
Setting the Clock
Powering Up and Setting the Clock............16
Operation
Using the CR-L5 .........................................19
Playing CDs ................................................20
Using the Radio...........................................22
Other Functions...........................................25
Timers .........................................................26
Thank you for purchasing the Onkyo CD Receiver.
Please read this manual thoroughly before making
connections and turning on the power.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new CD Receiver.
Appendix
Troubleshooting ..........................................29
Specifications ..............................................32
Please retain this manual for future reference.
En
CR-L5_E.book Page 3 Monday, May 19, 2003 4:05 PM
Important Safeguards—Continued
18. Object and Liquid Entry—Never push objects of any
kind into the appliance through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid
of any kind on the appliance.
19. Servicing—Do not attempt to service the appliance
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servic-
ing to qualified service personnel.
FIGURE 1:
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
20. Damage Requiring Service—Unplug the appliance
form the wall outlet and refer servicing to qualified ser-
vice personnel under the following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen into
the appliance,
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
NEC – NATIONAL ELECTRICAL CODE
ELECTRODE SYSTEM
(NEC ART 250, PART H)
S2898A
C. If the appliance has been exposed to rain or water,
D. If the appliance does not operate normally by follow-
ing the operating instructions.Adjust only those con-
trols that are covered by the operating instructions as
an improper adjustment of other controls may result
in damage and will often require extensive work by
a qualified technician to restore the appliance to its
normal operation,
E. If the appliance has been dropped or damaged in
any way, and
F. When the appliance exhibits a distinct change in
performance – this indicates a need for service.
21. Replacement Parts—When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unautho-
rized substitutions may result in fire, electric shock, or
other hazards.
22. Safety Check—Upon completion of any service or
repairs to the appliance, ask the service technician to
perform safety checks to determine that the appliance is
in proper operation condition.
23. Wall or Ceiling Mounting—The appliance should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
24. Heat—The appliance should be situated away from
heat sources such as radiators, heat registers, stoves, or
other appliances (including amplifiers) that produce
heat.
25. Liquid Hazards—The appliance should not be
exposed to dripping or splashing and no objects filled
with liquids, such as vases should be placed on the
appliance.
3
CR-L5_E.book Page 4 Monday, May 19, 2003 4:05 PM
Precautions
1. Recording Copyright
7. Moisture Condensation
Unless it’s for personal use only, recording copyrighted
material is illegal without the permission of the copy-
right holder.
Moisture condensation may damage this unit.
Read the following carefully:
When you take a glass containing a cold drink outside
on a summer’s day, drops of water, called condensation,
form on the outside of the glass. Similarly, moisture
may condense on the lens of the optical pickup, one of
the most important parts inside this unit.
2. AC Fuse
TheAC fuse inside the CR-L5 is not user-serviceable. If
you cannot turn on the CR-L5, contact your Onkyo
dealer.
• Moisture condensation can occur in the following sit-
uations:
— The unit is moved from a cold place to a warm
place.
— A heater is turned on, or cold air from an air con-
ditioner is hitting the unit.
— In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
— The unit is used in a humid place.
• Do not use this unit when there’s the possibility of
moisture condensation occurring. Doing so may
damage your discs and certain parts inside this unit.
If condensation does occur, remove all discs and leave
this unit turned on for two to three hours. By this time,
the unit will have warmed up and any condensation will
have evaporated. To reduce the risk of condensation,
keep this unit connected to a wall outlet.
3. Care
Occasionally you should dust the CR-L5 all over with a
soft cloth. For stubborn stains, use a soft cloth damp-
ened with a weak solution of mild detergent and water.
Dry the CR-L5 immediately afterwards with a clean
cloth. Don’t use abrasive cloths, thinners, alcohol, or
other chemical solvents, because they may damage the
finish or remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the CR-L5’s rear panel (AC
230 V, 50 Hz).
Setting the [STANDBY/ON] switch to STANDBY does
not fully shutdown the CR-L5. If you do not intend to
use the CR-L5 for an extended period, remove the
power cord from the AC outlet.
For British models
Replacement and mounting of anAC plug on the power sup-
ply cord of this unit should be performed only by qualified
service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance with
the following code:
5. Never Touch This Unit with Wet Hands
Never handle this unit or its power cord while your
hands are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo dealer.
Blue: Neutral
Brown: Live
6. Installing This Unit
As the colours of the wires in the mains lead of this appara-
tus may not correspond with the coloured markings identi-
fying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
• Install this unit in a well-ventilated location.
• Ensure that there’s adequate ventilation all around
this unit, especially if it’s installed in an audio rack. If
the ventilation is inadequate, the unit may overheat,
leading to malfunction.
• Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may rise,
shortening the life of the optical pickup.
• Avoid damp and dusty places, and places subject to
vibrations from loudspeakers. Never put the unit on
top of, or directly above a loudspeaker.
• Install this unit horizontally. Never use it on its side
or on a sloping surface, because it may cause a mal-
function.
• If you install this unit near a TV, radio, or VCR, the
sound quality may be affected. If this occurs, move
this unit away from the TV, radio, or VCR.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IMPORTANT
A 5 ampere fuse is fitted in this plug. Should the fuse need
to be replaced, please ensure that the replacement fuse has
a rating of 5 amperes and that it is approved byASTA or BSI
to BS1362. Check for the ASTA mark or the BSI mark on
the body of the fuse.
IF THE FITTED MOULDED PLUG IS UNSUITABLE
FOR THE SOCKET OUTLET IN YOUR HOME THEN
THE FUSE SHOULD BE REMOVED AND THE PLUG
CUT OFF AND DISPOSED OF SAFELY. THERE IS A
DANGER OF SEVERE ELECTRICAL SHOCK IF THE
CUT OFF PLUG IS INSERTED INTO ANY 13 AMPERE
SOCKET.
If in any doubt, consult a qualified electrician.
4
CR-L5_E.book Page 5 Monday, May 19, 2003 4:05 PM
Precautions—Continued
Declaration of Conformity
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT.” So, to
use this model properly, read this Instruction Manual
carefully. In case of any trouble, please contact the store
where you purchased the unit. To prevent exposure to
the laser beam, do not try to open the enclosure.
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE
6, 82194 GROEBENZELL,
GERMANY
declare in own responsibility, that the ONKYO product described
in this instruction manual is in compliance with the corresponding
technical standards such as EN60065, EN55013, EN55020 and
EN61000-3-2, -3-3.
DANGER:
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCK FAILED OR
DEFEATED. DO NOT STARE INTO BEAM.
GROEBENZELL, GERMANY
CAUTION:
I. MORI
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARD-
OUS RADIATION EXPOSURE.
ONKYO EUROPE ELECTRONICS GmbH
Memory backup
The CR-L5 uses a battery-less memory backup system in
order to retain radio presets and other settings when it’s
unplugged or in the case of a power failure. Although no
batteries are required, the CR-L5 must be plugged into an
AC outlet in order to charge the backup system.
Once it has been charged, the CR-L5 will retain the settings
for several weeks, although this depends on the environment
and will be shorter in humid climates. The clock setting is
not retained by the backup system.
This label is located on the rear panel. It indicates that:
1. This unit is a CLASS 1 LASER PRODUCT and
employs a laser inside the cabinet.
2. To prevent the laser from being exposed, do not
remove the cover. Refer servicing to qualified per-
sonnel.
Features
• 2 × 50 watts at 4 Ω, 1 kHz, DIN
• 4 Ω speaker drive capability
• Optical and coaxial digital outputs
• Subwoofer preout
*1
• WRAT (Wide Range Amplifier Technology)
• CDR and TAPE inputs/outputs
*2
• VLSC (Vector Linear Shaping Circuitry)
• A and B speaker outputs (Binding-post speaker termi-
nals)
• Direct mode
• RDS (Radio Data System), including PS (Program Ser-
vice Name), RT (Radio Text), and CT (Clock Time)
•
full-function remote control
• 4 timers for auto playback or recording
• 3-level display dimmer
• 40 radio presets
*1. Wide Range Amplifier Technology improves the imaging, realism, and accuracy of sound material.
*2. A proprietary Onkyo D/A converter, featuring Pulse Noise Reduction.
5
CR-L5_E.book Page 6 Monday, May 19, 2003 4:05 PM
Supplied Accessories
Check that the following accessories are supplied with this unit.
AM loop antenna
FM indoor antenna
Remote controller (RC-535S)
two batteries (AA/R6)
*
In catalogs and on packaging, the letter added to the end of the product name indicates the color of the CR-L5. Specifications and
operation are the same regardless of color.
Disc Notes
Handling Discs
Storing Discs
• Never touch the underside of a disc.Always hold discs by
the edge, as shown.
• Don’t store discs in places subject to direct sunlight, or
near heat sources.
• Don’t store discs in places subject to moisture or dust,
such as in a bathroom or near a humidifier.
• Always store discs in their cases and vertically. Stacking,
or putting objects on unprotected discs may cause warp-
ing, scratches, or other damage.
Supported Discs
Underside
The CR-L5 supports the following discs.
• Never attach adhesive tape or sticky labels to discs.
Disc
Logo
Format
Audio CD
PCM audio
About playing copy-controlled CDs
Some audio CDs feature copy protection that doesn’t con-
form to the official CD standard. Since these are nonstand-
ard discs, they may not play properly in the CR-L5.
Cleaning Discs
• For best results, keep your discs clean. Fingerprints and
dust can affect the sound quality and should be removed
as follows. Using a clean soft cloth, wipe from the center
outwards, as shown. Never wipe in a circular direction.
• The CR-L5 does not support disc types not listed.
• The CR-L5 does not support the following disc types
even if they bear the logo shown above: CD-R, CD-RW,
CD-ROM, Super Audio CD, Photo CD, CD-G.
• The CR-L5 supports 8 cm and 12 cm discs.
• Don’t use discs with an unusual shape, such as those
shown below, because you may damage the CR-L5.
✔
• To remove stubborn dust or dirt, wipe the disc with a
damp soft cloth, and then dry it with a dry cloth.
• Never use solvent-based cleaning fluids, such as thinner
or benzine, commercially available cleaners, or antistatic
sprays intended for vinyl records, because they may dam-
age the disc.
• Don’t use discs that have residue from adhesive tape,
rental discs with peeling labels, or discs with custom-
made labels or stickers. Doing so may damage the CR-L5
and you may not be able to remove the disc properly.
6
CR-L5_E.book Page 7 Monday, May 19, 2003 4:05 PM
Before Using the CR-L5
Installing the Remote Controller
Batteries
Using the Remote Controller
To use the remote controller, point it at the CR-L5’s remote
control sensor, as shown below.
1
Open the battery compartment, as
shown.
Remote control
sensor
CR-L5
STA
NDB
Y
/
O
N
STA
NDB
Y
PHO
NES
SPE
AKE
RS
A
/
B
MEM
ORY
FM
AR
M
ODE
VO
LUM
E
CLE
PAU
SE
TUN
ING
STOP
PLAY
DISP
LAY
INPU
T
DIRE
CT
PRE
SET
30˚
30˚
2
Insert the two supplied batteries (AA/
R6) in accordance with the polarity
diagram inside the battery compart-
ment.
Notes:
• The remote controller may not work reliably if the CR-L5
is subjected to bright light, such as direct sunlight or
inverter-type fluorescent lights. Keep this in mind when
installing the CR-L5.
• If another remote controller of the same type is used in
the same room, or the CR-L5 is installed close to equip-
ment that uses infrared rays, the remote controller may
not work reliably.
3
Close the battery compartment.
• Don’t put anything, such as a book, on the remote con-
troller, because the buttons may be pressed inadvertently,
thereby draining the batteries.
• The remote controller may not work reliably if the CR-L5
is installed in a rack behind colored glass doors. Keep this
in mind when installing the CR-L5.
Notes:
• The supplied batteries should last for about six months,
although this will vary with usage.
• If the remote controller doesn’t work reliably, try replac-
ing both batteries.
• Don’t mix new and old batteries, or different types of bat-
teries.
• The remote controller will not work if there’s an obstacle
between it and the CR-L5’s remote control sensor.
• If you intend not to use the remote controller for a long
time, remove the batteries to prevent possible leakage and
corrosion.
• Flat batteries should be removed as soon as possible to
prevent possible leakage and corrosion.
7
CR-L5_E.book Page 8 Monday, May 19, 2003 4:05 PM
Controls & Connectors
Front Panel
For detailed information, refer to the pages in parenthesis.
Disc Tray
12
3
4
5
VOLUME
STANDBY/ON
STANDBY
PAUSE
STOP
PLAY
PHONES
INPUT
DIRECT
SPEAKERS A/B
MEMORY FM MODE
CLEAR
DISPLAY
TUNING
PRESET
Display
6
7 89 J K
L M N O
ASTANDBY/ON button (16)
IFM MODE button (22–23)
Used to select stereo or mono for FM radio.
Sets the CR-L5 to On or Standby.
BSTANDBY indicator (16)
J[ ] & [ ] buttons (TUNING [ ] & [ ] buttons)
(20, 22)
Lights up when the CR-L5 is in Standby mode. It also
lights up when the CR-L5 receives signals from the
remote controller.
Used for fast reverse and fast forward when playing
CDs, or tuning when using the radio.
C[ ] button (20)
KRemote control sensor (7)
Opens and closes the disc tray.
Receives control signals from the remote controller.
DPAUSE [ ], STOP [ ] & PLAY [ ] buttons (20)
LDISPLAY button (16, 17, 20, 22–24)
Used to pause, stop, and start playback.
Used to change the displayed information.
EVOLUME control (19)
M[ ] & [
] buttons (PRESET [ ] & [ ]
Adjusts the volume.
buttons) (20–24)
Used to select the previous or next track when playing
CDs, or to select presets when using the radio.
FPHONES jack (19)
Used to connect a pair of stereo headphones.
NINPUT [ ] [ ] selector buttons (19, 22)
Used to select sound sources: CD, CD-R, TAPE, TV/
LINE, FM or AM.
GSPEAKERS A/B button (19)
Turns speaker sets A and B on and off.
HMEMORY button (22–24)
ODIRECT button & indicator (25)
Used to store radio presets.
Used to select Direct mode.
Display
For detailed information, refer to the pages in parenthesis.
1234
5 67890A
B
C D
8
CR-L5_E.book Page 9 Monday, May 19, 2003 4:05 PM
Controls & Connectors—Continued
1TRACK indicator
8MUTING indicator (25)
Appears when the CD input source is selected.
Lights up when the CR-L5 is muted.
2MEMORY indicator (21)
9RDS indicator (17, 23)
Lights up when memory playback is used.
Lights up when the CR-L5 is tuned to a radio station
that supports RDS (Radio Data System).
3RANDOM indicator (21)
0A & B speaker indicators (19)
Lights up when random playback is used.
IndicatorA lights up when speaker setA is on. Indicator
B lights up when speaker set B is on.
4REPEAT indicator (21)
Lights up when repeat playback is used.
ASLEEP indicator (28)
5FM STEREO indicator (22)
Lights up when the Sleep function has been set.
Lights up when tuned to a stereo FM station.
BMessage area
6AUTO indicator (22)
Various information is displayed here.
Lights up when auto stereo tuning is used.
CPlay/Pause
/
indicators (20)
7Tuned indicator (22)
Lights up when the CR-L5 is properly tuned to a radio
station.
Light up for playback and pause.
DTIMER indicators (27)
Light up when a timer has been set.
Rear Panel
For detailed information, refer to the pages in parenthesis.
1
2 3 4 5
6
AUDIO
OUTPUT
DIGITAL
SPEAKERS
A
SPEAKERS
B
ANTENNA
FM 75
L
L
CD RECEIVER
COAXIAL
-
MODEL NO. CR L
5
AM
SUB
TV/LINE
TAPE
CDR
WOOFER
AUDIO
ANALOG
PREOUT
OPTICAL
L
L
R
R
REMOTE
CONTROL
R
R
:
B
A OR B 4 OHMS MIN. / SPEAKER
+
:
A
8 OHMS MIN. / SPEAKER
IN
OUT
IN
OUT
IN
7 8 9 J
ASPEAKERS A (13)
GTV/LINE IN (11)
These terminal posts are for connecting speaker set A.
These RCA/phono connectors can be used to connect a
TV or other component.
BSPEAKERS B (13)
HTAPE IN/OUT (11)
These terminal posts are for connecting speaker set B.
These RCA/phono connectors can be used to connect a
cassette tape deck or other recorder with analog inputs
and outputs.
CSUBWOOFER PREOUT (13)
This RCA/phono connector can be used to connect an
active subwoofer. The subwoofer output is turned on
and off with speaker set A.
ICDR IN/OUT (11)
These RCA/phono connectors can be used to connect a
CD recorder or other recorder with analog inputs and
outputs.
DFM 75Ω ANTENNA (14, 15)
This connector is for connecting an FM antenna.
EAM ANTENNA (14, 15)
These push terminals are for connecting an AM
antenna.
J
REMOTE CONTROL (12)
This
(Remote Interactive) connector can be con-
nected to the
nent. To use
connector on another Onkyo compo-
, you must make an analog RCA/phono
FCOAXIAL & OPTICAL DIGITAL AUDIO OUTPUT
(11)
connection between the CR-L5 and your other compo-
nent, even if they are connected digitally.
These connectors can be used to connect a CD recorder
or other component with digital inputs.
9
CR-L5_E.book Page 10 Monday, May 19, 2003 4:05 PM
Controls & Connectors—Continued
KTONE button— Used to set the tone.
Remote Controller
LTIMER button— Used to set the timers.
MUp [ ] & Down [ ] buttons— Used to set the tim-
ers and tone.
NENTER button— Used to set the timers and tone.
OMUTING button— Used to mute the CR-L5.
PDIRECT button— Used to select Direct mode.
ON
STANDBY
1
2
TONE
INPUT
K
L
TIMER
3
QPrevious [
] & Next [
] buttons— Used to
1
4
7
2
5
3
select the previous or next track when playing CDs, or
to select presets when using the radio.
6
9
4
M
N
8
RDISPLAY button— Used to display information.
>
10
10/0
ENTER
SPLAY MODE button— Used to select random and
SLEEP
VOLUME
memory playback.
5
6
7
UP
TCLEAR button— Used with memory playback.
MUTING
DOWN
O
P
UREPEAT button— Used with repeat playback.
CLOCK CALL
DIRECT
Controlling an Onkyo Cassette Tape Deck
Q
R
S
T
U
8
9
J
DIMMER
DISPLAY
An Onkyo Cassette Tape Deck connected via
can be controlled as follows:
(page 12)
CD
PLAY MODE
CLEAR
1. Use the INPUT [ ]/[ ] selector buttons to select the
TAPE source.
2. Use the following buttons.
CDR
TAPE
REPEAT
[
[
[
] .................. Fast reverse
] .................. Fast forward
]..................... Other-side play
DIMMER
DISPLAY
-
RC 535S
CD
PLAY MODE
CLEAR
CDR
TAPE
[ ] ...................... Stop
]..................... Play
REPEAT
[
AON button— Turns on the CR-L5.
Controlling an Onkyo CD Recorder
BSTANDBY button— Sets the CR-L5 to Standby.
An Onkyo CD Recorder connected via
controlled as follows:
(page 12) can be
CINPUT [ ] [ ] selector buttons— Used to select
sound sources.
1. Use the INPUT [ ]/[ ] selector buttons to select the
CD-R source.
DNumber buttons— Used to select CD tracks and to
2. Use the following buttons.
set the clock.
ESLEEP button— Used with the Sleep function.
[
[
[
[
]................... Fast reverse
]................... Fast forward
] .................. Previous track
] .................. Next track
FVOLUME UP [ ] & DOWN [ ] buttons— Used
DIMMER
DISPLAY
to set the volume.
CD
PLAY MODE
CLEAR
GCLOCK CALL button— Used to display the current
CDR
TAPE
[ ]...................... Pause
[ ] ...................... Stop
[
[REPEAT].......... Repeat mode
[PLAY MODE].. Play mode
time.
REPEAT
HFast Reverse [ ] & Fast Forward [
]
]..................... Play
buttons— Used for fast reverse and fast forward when
playing CDs, or for tuning when using the radio.
IDIMMER button— Used to set the display brightness.
JCD control buttons— Used to control CD playback.
10
CR-L5_E.book Page 11 Monday, May 19, 2003 4:05 PM
ConnectingYour Other Components to the CR-L5
• Don’t connect the power cord until you’ve completed all
connections, including connections on page 12,
speaker connections on page 13, and antenna connections
on page 14.
• Refer to the manuals supplied with your other compo-
nents before connecting them.
RCA/phono Audio Cable Color Coding
RCA/phono audio cables are usually color coded: red and
white. Use red plugs to connect right-channel audio inputs
and outputs (typically labeled “R”). And use white plugs to
connect left-channel audio inputs and outputs (typically
labeled “L”).
Optical Digital Output
Right (red)
Left (white)
Right (red)
Left (white)
The CR-L5’s optical digital connector
has a dust cap for keeping out dust and
dirt when it’s not in use. Remove the
cap before inserting an optical digital
plug. Push the plug in all the way to
make a good connection. Keep the
dust cap in a safe place for future use.
Right!
• Push the plugs in all the way to
make a good connection.
• To prevent interference, keep
audio cables away from power
cords and speaker cables.
• You can connect a DAT or CD recorder with a digital
audio input to the CR-L5 for digital dubbing.
Wrong!
Cassette Tape Deck
CD recorder
ANALOG
INPUT OUTPUT
ANALOG
INPUT
OUTPUT
INPUT
L
L
OPTICAL
DIGITAL
R
R
AUDIO
OUTPUT
DIGITAL
COAXIAL
TAPE
CDR
AUDIO
LOG
OPTICAL
R
OUT
IN
OUT
IN
AUDIO
SPEAKERS
A
SPEAKERS
B
ANTENNA
FM 75
OUTPUT
DIGITAL
L
L
CRECEIVER
COAXIAL
-
MODEL NO. CR
L5
AM
SUB
TV/LINE
TAPE
CDR
WOOFER
AUDIO
ANALOG
PREOUT
OPTICAL
L
L
R
R
REMOTE
CONTROL
R
R
IN
OUT
IN
OUT
IN
TV/LINE
L
R
IN
TV
L
R
AUDIO OUT
11
CR-L5_E.book Page 12 Monday, May 19, 2003 4:05 PM
Connecting
-compatible Components
With
(Remote Interactive) you can control your
-
To use
to an
, you need to connect the CR-L5’s
connector on the other component by using an
cable is supplied with each -compat-
connector
compatible Onkyo cassette tape deck or CD recorder with
the CR-L5’s remote controller, and use the following spe-
cable. An
cial
functions:
ible Onkyo cassette tape deck and CD recorder.
Hookup Example:
■ Auto Power On
When you turn on a component connected via
while the
Onkyo CD recorder
CR-L5 is in Standby, the CR-L5 automatically turns on and
selects that component as the input source.
This function doesn’t work if the CR-L5 is already on.
DIGITAL IN
OPTICAL
REMOTE
CONTROL
L
L
■ Direct Change
When you press the play button on a component connected
R
R
via
, the CR-L5 automatically selects that component as
ANALOG
INPUT
ANALOG
OUTPUT
the input source.
■ Auto Power Off
To use
must make an
analog RCA/
phono connec-
tion between
the CR-L5 and
the other com-
ponent even if
they are con-
nected digitally.
you
When you set the CR-L5 to Standby, all components con-
nected via
also enter Standby.
■ Controlling Other Components
Other components can be controlled with the supplied
remote controller (see “Remote Controller” on page 10).
cable
■ CD Synchro Recording
A CD recorder or cassette tape deck connected via
set to record pause, will start recording automatically when
CD playback is started on the CR-L5.
, and
AUDIO
OUTPUT
DIGITAL
COAXIAL
CDR
■ Timer
OPTICAL
REMOTE
The CR-L5’s timers can be used to automatically start play-
back or recording on a cassette tape deck or CD recorder
CONTROL
OUT
IN
connected via
(see “Timers” on page 26).
■ Sleep Timer
AUDIO
OUTPUT
DIGITAL
SPEAKERS
A
SPEAKERS
B
ANTENNA
FM 75
L
L
COAXIAL
CD RECEIVER
-
MODEL NO. CR
L5
When you set the CR-L5’s sleep timer, the sleep timers on
components connected via are also set, so all compo-
nents switch off after the specified period.
AM
SUB
TV/LINE
TAPE
CDR
WOOFER
PREOUT
AUDIO
ANALOG
OPTICAL
L
L
R
R
REMOTE
CONROL
R
R
N.
N.
/
/
SPEAKER
SPEAKER
IN
OUT
IN
OUT
IN
Notes:
• Push the plugs in all the way to make a good connection.
• Use only
cables for
connections.
• To use
you must make an analog RCA/phono con-
nection between the CR-L5 and the other component
even if they are connected digitally.
• If a component has two
connectors, you can connect
either one to the CR-L5. The other connector is for con-
necting additional
-compatible components.
• Connect the CR-L5’s
connector to only Onkyo com-
ponents. Connecting to other manufacturer’s components
may cause them to malfunction.
• Some Onkyo
-compatible components may not sup-
port the special functions described above.
12
CR-L5_E.book Page 13 Monday, May 19, 2003 4:05 PM
ConnectingYour Speakers
Before you connect your speakers, read the following:
• Disconnect the power cord from the wall outlet.
• Read the instructions supplied with your speakers.
• Pay close attention to speaker wiring polarity. Connect
positive (+) terminals only to positive (+) terminals, and
negative (–) terminals only to negative (–) terminals. If
you get them the wrong way around, the sound will be out
of phase and will sound odd.
You can use two sets of speakers with your CR-L5: speaker
set A and speaker set B.
Speaker setA consists of front left and right speakers and a
subwoofer and should be installed in your main listening
room.
Speaker set B consists of front left and right speakers and
can be installed in another room, such as a dining room or
kitchen.
• If you’re connecting two sets of speakers (i.e., speaker set
A and speaker set B), the minimum impedance for each
speaker is 8 Ω. If you’re connecting only one set of speak-
ers (i.e., speaker set A or speaker set B), the minimum
impedance for each speaker is 4 Ω. Don’t connect speak-
ers with a lower impedance.
• Unnecessarily long, or very thin speaker cables may
affect the sound quality and should be avoided.
• Be careful not to short the positive
1
Strip 15 mm (5/8") of
insulation from the
ends of the speaker
cables, and twist the
bare wires tightly, as
shown.
15 mm (5/8")
and negative connections. Doing so
may damage your CR-L5.
• Don’t connect more than one cable to
each speaker terminal. Doing so may
2
3
Unscrew the terminal.
damage your CR-L5.
• If you want to connect a single speaker instead of a pair
of speakers, don’t connect it to both the left and right
speaker terminals.
Fully insert the wire.
L
L
4
Screw the terminal tight.
R
R
The following illustration shows how you should connect your speakers.
Speakers Set A
The SUBWOOFER PRE OUT should be
connected to the input on your active
subwoofer. If your subwoofer doesn’t have an
amp built-in, you’ll need to use an external
amp. See the manual supplied with your
subwoofer for more information.
Front-
right
speaker
Front-
left
speaker
Active
sub-
woofer
AUDIO
OUTPUT
DIGITAL
SPEAKERS
A
SPEAKERS
B
ANTENNA
FM 75
L
L
CD RECEIVER
COAXIAL
-
MODEL NO. CR L
5
AM
SUB
TV/LINE
TAPE
CDR
WOOFER
AUDIO
ANALOG
PREOUT
OPTICAL
L
L
R
R
REMOTE
CONTROL
R
R
:
:
A
OR
B
B
4
8
OHMS MIN. / SPEAKER
OHMS MIN. / SPEAKER
+
A
IN
OUT
IN
OUT
IN
Front-
right
speaker
Front-
left
speaker
Speakers Set B
13
CR-L5_E.book Page 14 Monday, May 19, 2003 4:05 PM
Connecting Antenna
This chapter explains how to connect the supplied indoor
FM antenna andAM loop antenna, and how to connect com-
mercially available outdoor FM and AM antennas.
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor
use only.
FM antenna
connector
AM antenna
push terminals
1
Assemble the AM loop antenna,
inserting the tabs into the base, as
shown.
ANTENNA
FM 75
AM
AUDIO
OUTPUT
DIGITAL
SPEAKERS
A
SPEAKERS
B
ANTENNA
FM 75
L
L
COAXIAL
CD RECEIVER
MODEL NO. CR-L
5
AM
SUB
TV/LINE
TAPE
CDR
WOOFER
AUDIO
ANALOG
PREOUT
OPTICAL
L
L
R
R
REMOTE
CONTROL
R
R
A
OR B:
A+B:
4
8
OHMS MIN.
OHMS MIN.
/
/
SPEAKER
SPEAKER
IN
OUT
IN
OUT
IN
Connecting the Indoor FM Antenna
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
The supplied indoor FM antenna is for indoor use only.
(The antenna’s wires are not polarity sensitive, so they
can be connected either way around.)
Make sure that the wires are attached securely and that
the push terminals are gripping the bare wires, not the
insulation.
1
Attach the FM antenna, as shown.
ANTENNA
FM 75
Insert the plug fully
into the socket.
Once your CR-L5 is ready for use, you’ll need to tune
into an FM radio station and adjust the position of the
FM antenna to achieve the best possible reception.
Push
Insert wire
Release
2
Use thumbtacks or something similar
to fix the FM antenna into position.
AM
Once your CR-L5 is ready for use, you’ll need to tune
into an AM radio station and adjust the position of the
AM antenna to achieve the best possible reception.
Keep the antenna as far away as possible from your
CR-L5, TV, speaker cables, and power cords.
Thumbtacks, etc.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commercially
available outdoor AM antenna (see page 15).
Caution: Be careful that you don’t injure yourself
when using thumbtacks.
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor
FM antenna instead (see page 15).
14
CR-L5_E.book Page 15 Monday, May 19, 2003 4:05 PM
Connecting Antenna—Continued
Connecting an Outdoor FM Antenna
Connecting an Outdoor AM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available outdoor
FM antenna instead.
If good reception cannot be achieved using the suppliedAM
loop antenna, an outdoor AM antenna can be used in addi-
tion to the loop antenna, as shown.
Outdoor antenna
Insulated
antenna cable
AM loop antenna
ANTENNA
FM 75
AM
OutdoorAM antennas work best when installed outside hor-
izontally, but good results can sometimes be obtained
indoors by mounting horizontally above a window. Note
that the AM loop antenna should be left connected.
Outdoor antenna must be grounded in accordance with local
regulations to prevent electrical shock hazards. See item 14
of the “Important Safeguards” on page 2 of this manual.
Notes:
• Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in an
attic or loft.
• For best results, install the outdoor FM antenna well away
from tall buildings, preferably with a clear line of sight to
your local FM transmitter.
• Outdoor antenna should be located away from possible
noise sources, such as neon signs, busy roads, etc.
• For safety reasons, outdoor antenna should be situated
well away from power lines and other high-voltage equip-
ment.
• Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards. See
item 14 of the “Important Safeguards” on page 2 of this
manual.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and TV
reception, as this can cause interference problems. If cir-
cumstances demand it, use a TV/FM antenna splitter, as
shown.
TV/FM antenna splitter
To TV (or VCR)
To CR-L5
15
CR-L5_E.book Page 16 Monday, May 19, 2003 4:05 PM
Powering Up and Setting the Clock
STANDBY/ON
ON
STANDBY
ON
STANDBY/ON
STANDBY
PAUSE
STOP
P
TONE
STANDBY
▼
1
▲
2
INPUT
TIMER
PHONES
INPUT
DIRE
SPEAKERS
A
/B
MEMORY FM MODE
CLEAR
DISPLAY
3
TIMER
ENTER
TUNING
PRESET
▲
▼
4
5
6
9
7
8
STANDBY indicator
DISPLAY
>
10
10/0
ENTER
SLEEP
VOLUME
UP
MUTING
DOWN
CLOCKCALL
CLOCK CALL
DIRECT
Powering Up the CR-L5
Before connecting the power cord, complete all connections
(see page 11 to 15).
DIMMER
DISPLAY
DISPLAY
CD
PLAY MODE
CLEAR
CDR
1
Connect the power cord to a suitable
wall outlet.
The CR-L5 enters Standby mode, and the STANDBY
indicator comes on.
Turning Off ACCUCLOCK
If you don’t want ACCUCLOCK to automatically update
the clock at 2 A.M., 3 A.M. and 2 P.M. everyday, you can
turn it off as follows.
2
To turn on the CR-L5, press the
[STANDBY/ON] button or the remote
controller’s [ON] button.
1
2
Press the [TIMER] button repeatedly
until “Clock” appears on the display,
as shown.
The CR-L5 comes on, the display lights up, and the
STANDBY indicator goes off.
To turn off the CR-L5, press the [STANDBY/ON] but-
ton or the remote controller’s [STANDBY] button. The
CR-L5 enters Standby mode and the STANDBY indi-
cator comes on.
First Time Setup
Press the [ENTER] button.
“AccuClock” appears on the display, as shown.
The very first time you turn on the CR-L5, the ACCU-
CLOCK function automatically sets the clock by using the
CT (Clock Time) information present in RDS radio broad-
casts.
While the clock is being set, “Wait” flashes on the display,
as shown. It may take up to five minutes to set the clock.
These asterisks appear when
the ACCUCLOCK function is on
If “Manual Adj.” appears, use the Up/Down [ ]/[ ]
buttons to select “AccuClock”.
When the clock has been set, the message “ClockAdjusted”
scrolls across the display, then the day and time are dis-
played for a while, as shown.
3
To turn off ACCUCLOCK, press the
[DISPLAY] button.
The asterisks disappear, indicating that the ACCU-
CLOCK function is off.
To turn the ACCUCLOCK function on again, press the
[DISPLAY] button so that asterisks appear.
If the clock has not been set correctly, see “Displaying the
Day & Time” on page 17.
The ACCUCLOCK function automatically updates the
clock daily at 2 A.M., 3 A.M. and 2 P.M..
16
CR-L5_E.book Page 17 Monday, May 19, 2003 4:05 PM
Powering Up and Setting the Clock—Continued
Displaying the Time in Standby
Mode
Setting ACCUCLOCK to Use a
Specific Station
You can set the CR-L5 so that the time is displayed while
the CR-L5 is in Standby mode.
The ACCUCLOCK function normally uses the FM station
with the strongest signal to set the clock. If the clock cannot
be set properly using that station, you can specify which FM
station the ACCUCLOCK function should use. This must
be an FM station that supports RDS CT (Clock Time) infor-
mation.
1
With the CR-L5 turned on, press and
hold the CR-L5’s [STANDBY/ON] but-
ton for more than 2 seconds.
To turn off the time display, repeat this procedure.
1
Press the [TIMER] button.
“Clock” appears on the display.
Notes:
• Setting the CR-L5 to display the time will slightly
increase the power consumption in Standby mode.
If the clock has already been set, a timer option appears
instead. In this case, you’ll need to press the [TIMER]
button repeatedly until “Clock” appears.
Displaying the Day & Time
2
3
Press the [ENTER] button.
You can display the day and time at anytime.
“AccuClock” appears on the display.
If “Manual Adj.” appears, use the Up/Down [ ]/[ ]
buttons to select “AccuClock”.
1
Press the [CLOCK CALL] button.
The day and time appear on the display.
Press the [DISPLAY] button to toggle between 12- and
24-hour formats.
Press the [ENTER] button.
The display appears as shown (the frequency will be
different).
Press the [CLOCK CALL] button again to return to the
previous display.
AC means ACCUCLOCK
If the correct day and time appear on the display, you
can skip the following sections and go straight to page 19
for information on using and enjoying your CR-L5.
If “Adjust” appears on the display:
The clock has not been set for one of the following reasons:
• The FM antenna is not connected properly or the signal is
too weak.
Check the antenna connection or install an outdoor FM
antenna (see page 15), and try setting again (see “Setting
ACCUCLOCK to Use a Specific Station” on this page).
• The detected RDS station does not support CT (Clock
Time) information.
4
5
Use the [ ]/[ ] buttons to tune into
the FM station.
The RDS indicator appears when tuned into a station
that supports RDS, as shown.
If you’ve stored some radio presets, you can use the
PRESET [
]/[
] buttons to select the FM station.
RDS indicator
Some RDS stations don’t support CT. In this case you
should specify the station to be used (see “Setting
ACCUCLOCK to Use a Specific Station” on this page).
If the wrong day or time appears on the display:
If you live close to the border with another country, the CT
information may have been taken from a radio station in
another time zone. In this case you should specify another
station and try setting again (see “Setting ACCUCLOCK to
Use a Specific Station” on this page).
Press the [ENTER] button.
While the clock is being set, “Wait” flashes on the dis-
play. It may take a few minutes to set the clock.
When the clock has been set, the message “Clock
Adjusted” scrolls across the display, then the day and
time are displayed for a while.
Notes:
• If the clock has not been set correctly, specify another FM
station and try again, or set the clock manually (see
page 18).
• If you don’t want the clock to be updated automatically,
you can turn off theACCUCLOCK function (see page 16).
17
CR-L5_E.book Page 18 Monday, May 19, 2003 4:05 PM
Powering Up and Setting the Clock—Continued
Setting the Clock Manually
4
5
Use the Up/Down [ ]/[ ] buttons to
select a day.
If you cannot set the clock by using the ACCUCLOCK
function, you can set it manually. In this case, the ACCU-
CLOCK function will not automatically update the clock
each day.
You can set the clock while the CR-L5 is on or in Standby.
Press the [ENTER] button.
The time flashes.
ON
STANDBY
TONE
▼
1
▲
2
INPUT
TIMER
3
TIMER
ENTER
Number
buttons
▲
▼
4
5
6
9
7
8
>
10
10/0
ENTER
>10
SLEEP
VOLUME
UP
MUTING
DOWN
CLOCK CALL
DIRECT
6
7
Use the Up/Down [ ]/[ ] buttons to
set the time.
DIMMER
DISPLAY
DISPLAY
CD
PLAY MODE
CLEAR
1
Press the [TIMER] button.
“Clock” appears on the display, as shown.
You can use the number buttons to enter the time. For
example, to enter 19:03, press [1], [9], [10/0], and [3].
Use the [DISPLAY] button to toggle between 12- and
24-hour formats.
While the 12-hour format is selected, use the [>10] but-
ton to toggle between AM and PM.
If the clock has already been set, a timer option appears
instead. In this case, you’ll need to press the [TIMER]
button repeatedly until “Clock” appears.
Press the [ENTER] button to set the
clock.
The seconds indicator starts flashing, as shown.
2
3
Press the [ENTER] button and use the
Up/Down [ ]/[ ] buttons to select
“Manual Adj.”.
Note: To cancel this procedure at any point before step 7,
press the [TIMER] button.
Press the [ENTER] button.
The day of the week flashes.
18
CR-L5_E.book Page 19 Monday, May 19, 2003 4:05 PM
Using the CR-L5
VOLUME control
Selecting Speaker Sets
VOLUME
When you connect two sets of speakers, you can listen to set
A, set B, or both.
PAUSE
STOP
PLAY
INPUT
DIRECT
SPEAKERS
A
/B
MEMORY FM MODE
CLEAR
DISPLAY
TUNING
PRESET
1
Use the [SPEAKERS A/B] button to
select the following options: A, B,
A+B, or off.
SPEAKERS A/B
INPUT
A
B
A
B
Off
ON
STANDBY
TONE
INPUT
/
The speaker indicators on the display show the current
setting. In the following example, only speaker set A is
on.
▼
1
▲
2
INPUT
TIMER
3
▲
▼
4
5
6
9
7
8
>
10
10/0
ENTER
SLEEP
VOLUME
VOLUME UP
UP
MUTING
DOWN
VOLUME DOWN
CLOCK CALL
DIRECT
DIMMER
DISPLAY
CD
PLAY MODE
CLEAR
CDR
Adjusting the Volume
TAPE
REPEAT
1
To adjust the volume,use theVOLUME
control, or the remote controller’s
-
RC 535S
VOLUME [ ]/[ ] buttons.
Turn the VOLUME control clockwise to increase the
volume; counterclockwise to decrease it.
Selecting Sound Sources
Using Headphones
1
Use the INPUT [ ]/[ ] buttons, or the
remote controller’s INPUT [ ]/[ ] but-
tons to select one of the following
sound sources: CD, FM or AM, CD-R,
You can connect a pair of stereo headphones (1/4-inch
phone plug) to the CR-L5’s PHONES jack for private listen-
ing, as shown.
TAPE,TV/LINE.
The currently selected source is shown on the display.
In the following example, CD has been selected.
STANDBY/ON
STANDBY
PHONES
2
If you selected CD, see “Playing CDs”
on page 20.
If you selected AM or FM, see “Using the Radio” on
page 22.
Notes:
• Always turn down the volume before connecting your
headphones.
If you selected CD-R, TAPE, or TV/LINE, start play-
back on the relevant component.
• Speaker setsA and B are turned off while the headphones
plug is inserted in the PHONES jack.
19
CR-L5_E.book Page 20 Monday, May 19, 2003 4:05 PM
Playing CDs
■ To Fast Forward or Fast Reverse
During playback or while playback is paused, press and
hold the [ ] button to fast forward, or the [ ] button to
fast reverse.
PAUSE
STOP
PLAY
VOLUME
PAUSE
STOP
PLAY
If you press the button for more than four seconds, the fast
forward or fast reverse speed increases.
INPUT
DIRECT
SPEAKERS
A
/B
MEMORY FM MODE
CLEAR
DISPLAY
TUNING
PRESET
■ To Select Tracks
DISPLAY
Press the [
] button to select the next track, or the [
]
button to select the previous track.
If you press the [ ] button during playback or while play-
back is paused, the beginning of the current track is
selected.
ON
STANDBY
TONE
▼
1
▲
2
INPUT
If you select a track while playback is stopped, press the
Play [ ] button to start playback.
TIMER
3
Number
buttons
▲
▼
4
5
6
9
Notes:
7
8
• If the CR-L5 is in Standby and a disc is loaded, you can
start playback simply by pressing the Play [ ] button.
The CR-L5 will turn on and the CD source will be
selected automatically.
>
10
10/0
ENTER
ENTER
>10
SLEEP
VOLUME
UP
MUTING
DOWN
CLOCK CALL
DIRECT
• With CDs that contain many tracks, playback may take a
while to start.
CD
operation
buttons
DIMMER
DISPLAY
DISPLAY
PLAY MODE
CLEAR
CD
PLAY MODE
CLEAR
CDR
Selecting Tracks by Number
TAPE
REPEAT
REPEAT
You can use the number buttons to select specific tracks.
RC 535S
1
During playback, use the number but-
Playing CDs
tons to enter a track number.
Use the [>10] button to enter track numbers above 9.
For example, to enter track number 20, press [>10], [2],
and [10/0].
1
Press the [ ] button to
Label side
open the disc tray, put the
CD on the tray with the
label-side facing up, and
press the [ ] button again
to close the tray.
Displaying the Remaining Time
1
During playback, press the [DISPLAY]
button repeatedly to display the
elapsed track time, remaining track
time, or remaining disc time.
If you’re using the Memory function to play a custom
selection of tracks, the remaining memory playback
time is displayed, instead of the remaining disc time.
Be sure to put 8-cm discs in the center of the tray.
2
Press the Play [ ] button to start play-
back.
Playback starts and the Play indicator appears on the
display.
Note: If the total playing time of your custom selection
exceeds 99 minutes and 59 seconds, “---:--” is displayed.
■ To Stop Playback
• Press the Stop [ ] button.
■ To Pause Playback
• Press the Pause [ ] button. The Pause indicator
appears.
• To resume playback, press the Play [ ] button.
20
CR-L5_E.book Page 21 Monday, May 19, 2003 4:05 PM
Playing CDs—Continued
In this example, track #8 is the fifteenth track to be
added to the program.
Repeat Playback
With the Repeat function you can play all tracks repeatedly.
1
2
During playback, press the remote
controller’s [REPEAT] button.
The REPEAT indicator appears on the display and all
tracks are played repeatedly.
The total memory playback time is displayed.
To cancel Repeat playback, press the
[REPEAT] button again.
You can check which tracks you’ve added to the pro-
gram by using the [ ]/[ ] buttons.
You can add up to 25 tracks to your program.
The REPEAT indicator disappears.
Notes:
• If you press the [REPEAT] button during memory play-
back, your custom program will play repeatedly.
• If you press the [REPEAT] button during random play-
back, tracks will be played in random order repeatedly.
3
To start memory playback, press the
Play [ ] button.
Memory playback stops automatically when all the
tracks in the program have been played.
Random Playback
With the Random function you can play tracks in random
order.
■ To Stop Memory Playback
Press the Stop [ ] button.
1
While stopped, press the [PLAY
MODE] button repeatedly until the
RANDOM indicator appears on the
display.
■ To Remove the Last Track in the
Program
While memory playback is stopped, press the [CLEAR]
button. Each time you press it the last track in the program
is removed.
2
3
Press the Play [ ] button to start ran-
dom playback.
■ To Cancel Memory Playback
While memory playback is stopped, press the [PLAY
MODE] button repeatedly until the MEMORY indicator
disappears. The entire program will be deleted.
To cancel random playback, stop play-
back, and then press the [PLAY
MODE] button repeatedly until the
RANDOM indicator disappears.
Notes:
• If you try to add more than 25 tracks to your program, the
message “Memory Full” appears on the display.
• If the total playing time of your program exceeds 99 min-
utes and 59 seconds, “---:--” is displayed. (This does not
affect program playback.)
Memory Playback
• The program is deleted when the disc tray is opened.
With the Memory function you can make a custom program
of your favorite tracks.
1
While stopped, press the [PLAY
MODE] button repeatedly until the
MEMORY indicator appears on the
display.
2
To add a track to your program, use
the [ ]/[ ] buttons to select it, and
then press the [ENTER] button.
Tracks can also be added by using the number buttons.
For example, to add track number 6, press [6]. To add
track 13, press [>10], [1], [3].
21
CR-L5_E.book Page 22 Monday, May 19, 2003 4:05 PM
Using the Radio
DISPLAY
Presetting FM Stations
Automatically
STANDBY/ON
STANDBY
PAUSE
STOP
PL
With the Auto Preset function you can automatically preset
all the FM stations available in your area.
PHONES
INPUT
DIREC
SPEAKERS
A
/B
MEMORY FM MODE
CLEAR
DISPLAY
TUNING
PRESET
TUNING
FM MODE
PRESET
INPUT
1
2
Use the INPUT [ ]/[ ] buttons, or the
remote controller’s INPUT [ ]/[ ] but-
tons to select FM.
MEMORY
ON
STANDBY
Press and hold the [MEMORY] button
until “Auto Preset” flashes on the dis-
TONE
INPUT
/
▼
1
▲
2
INPUT
TIMER
3
▲
▼
4
5
6
9
play.
7
8
Hold down the button for a few more seconds until the
Auto Preset function starts.
>
10
10/0
ENTER
SLEEP
VOLUME
UP
The Auto Preset function scans the FM band from low
to high, presetting up to 30 stations with strong signals.
MUTING
DOWN
CLOCK CALL
DIRECT
Note: All previously stored presets will be overwritten
when the Auto Preset function is used again.
DIMMER
DISPLAY
DISPLAY
D
PLAY MODE
Presetting Stations Manually
You can preset up to 40 of your favorite AM and FM radio
stations in total.
Tuning the Radio
1
Use the INPUT [ ]/[ ] buttons, or the
remote controller’s INPUT [ ]/[ ] but-
tons to select AM or FM.
1
2
3
Tune into the station that you want to
store as a preset.
Press the [MEMORY] button.
The preset number flashes.
2
Use theTUNING [ ]/[ ] buttons, or the
remote controller’s [ ]/[ ] buttons
to tune the radio.
While the preset number is flashing,
use the PRESET [ ]/[ ] buttons to
select a preset from 1 through 40.
In this example, preset #3 has been selected.
If you select the FM band:
To automatically search for a station, press and hold a
TUNING [ ]/[ ] button for more than half a second
and then release it. The CR-L5 searches for the next
station. Searching stops when a station is found and the
Tuned
and FM STEREO indicators appear. If
necessary, you can use the TUNING [ ]/[ ] buttons
for fine tuning.
The FM band is searched in 0.05 MHz intervals.
If you select the AM band:
4
Press the [MEMORY] button to store
the station.
The station is stored and the preset number stops flash-
Press the TUNING [ ] or [ ] button to change the fre-
quency one interval at a time, or press and hold the but-
ton to quickly change the frequency. When you’re
ing.
tuned into a station, the Tuned
indicator appears.
Repeat this procedure for all of your favorite radio sta-
tions.
The AM band is searched in 9 kHz intervals.
Notes:
Tuning into weak FM stations
• If you try to store more than 40 stations, the message
“Memory Full” appears on the display.
• When the CR-L5 is tuned into a station that’s transmitting
PS (Program Service Name) RDS information, the sta-
tion’s name will be displayed instead of the frequency.
If a station has a poor signal strength, you may not be able
to tune into that station properly, or reception may be noisy.
In this case, press the [FM MODE] button. The AUTO and
FM STEREO indicators go off and mono mode is selected.
22
CR-L5_E.book Page 23 Monday, May 19, 2003 4:05 PM
Using the Radio—Continued
Selecting Presets
RDS (Radio Data System)
You can select previously stored presets as follows.
The Radio Data System (RDS) allows FM radio stations to
broadcast various information to RDS-compatible radios,
including the name of the radio station and information
about the program being broadcast. Many FM stations in
most European countries transmit RDS information.
The CR-L5 supports the following RDS information:
PS: Program Service Name
When tuned into a station that transmits PS information, the
station’s name appears on the display.
RT: Radio Text
1
2
Use the INPUT [ ]/[ ] buttons, or the
remote controller’s INPUT [ ]/[ ] but-
tons to select AM or FM.
Use the PRESET [ ]/[ ] buttons, or
the remote controller’s [ ]/[ ] but-
tons to select a preset.
When tuned into a station that transmits RT information,
any text messages received appear on the display.
Deleting Presets
You can delete unwanted presets as follows.
When the CR-L5 is tuned into a station that’s transmitting
RDS information, the RDS indicator appears on the display.
To display the PS and RT information, press the [DISPLAY]
button repeatedly to select Frequency display, PS, or RT, as
shown.
1
Select the preset that you want to
delete.
See the previous section for information on selecting
presets.
Frequency
PS (Program Service Name)
RT (Radio Text)
In this example, preset #3 has been selected.
When the CR-L5 receives RT information, “Waiting”
appears on the display first, and then the received text
scrolls across the display.
2
While holding down the [MEMORY]
button, press the [FM MODE] button.
The selected preset is deleted and its number disap-
pears from the display.
23
CR-L5_E.book Page 24 Monday, May 19, 2003 4:05 PM
Using the Radio—Continued
Naming Presets
Editing Preset Names
You can name your radio presets for easy identification.
Names can be up to eight characters long.
You can edit the names of presets as follows.
1
Select the preset whose name you
want to edit.
DISPLAY
See page 23 for information on selecting presets.
STANDBY/ON
STANDBY
PAUSE
STOP
PL
PHONES
INPUT
DIREC
SPEAKERS
A
/B
MEMORY FM MODE
CLEAR
DISPLAY
TUNING
PRESET
2
3
Press and hold down the [DISPLAY]
button for about 3 seconds.
MEMORY
TUNING
PRESET
Use the TUNING [ ]/[ ] buttons to
select the character that you want to
edit.
1
Select the preset that you want to
name.
The currently selected character flashes.
See page 23 for information on selecting presets.
4
5
Use the PRESET [ ]/[ ] buttons to
select a new character.
2
3
Press and hold down the [DISPLAY]
button for about 3 seconds.
Repeat steps 3 and 4 to edit other characters.
To delete a character, select it, and choose “_(space)”.
Use the PRESET [ ]/[ ] buttons to
select a character.
Select the eighth character, and then
press the [MEMORY] button to con-
firm the edit.
The following characters are available:
_(space) A B C D E F G H I J K L
M N O P Q R S T U V W X Y Z
a b c d e f g h i j k l m n o p q r s t u
v w x y z
" ' @ & ( ) * + , - . / = ?
0 1 2 3 4 5 6 7 8 9
Displaying a Preset Station’s
Frequency
When a preset has been named, when it’s selected, its name
appears on the display.You can display the frequency of the
preset’s station as follows.
Select “_(space)” if you want to leave a space between
words.
1
Press the [DISPLAY] button repeat-
edly to display the preset name or pre-
set frequency (and preset number).
4
5
Press the [MEMORY] button to enter
the character.
The cursor moves to the next character.
Repeat steps 3 and 4 to enter seven
more characters.
When you press the [MEMORY] button after selecting
the eighth character, “Complete” appears on the dis-
play, indicating that the naming process is complete. If
the name you’re entering consists of less than eight
characters, to complete the process, select “_(space)”
and then press [MEMORY].
Notes:
• You can’t name presets set to RDS stations that transmit
PS (Program Service Name) information. See page 23 for
more information on RDS.
24
CR-L5_E.book Page 25 Monday, May 19, 2003 4:05 PM
Other Functions
Adjusting the Bass & Treble
ON
STANDBY
With the Bass and Treble functions you can adjust the tone
of the sound to your personal preference.
TONE
▼
1
▲
2
INPUT
TONE
TIMER
3
▲
▼
4
5
6
9
1
2
Use the remote controller’s [TONE]
button to select “Bass” or “Treble”.
7
8
>
10
10/0
ENTER
ENTER
SLEEP
VOLUME
UP
Use the remote controller’s Up/Down
[ ]/[ ] buttons to adjust the bass or
MUTING
DOWN
MUTING
DIRECT
CLOCK CALL
DIRECT
treble.
DIMMER
DISPLAY
DIMMER
The bass and treble can be adjusted from –10 to +10 in
increments of 2.
CD
PLAY MODE
CLEAR
CDR
3
When you’ve finished, press the
[ENTER] button.
You can temporarily bypass the Bass and Treble func-
tions by using Direct mode.
Muting the CR-L5
With this function you can temporarily mute the output of
the CR-L5.
Using Direct Mode
1
Press the remote controller’s [MUT-
ING] button.
The output is muted and the MUTING indicator flashes
on the display, as shown.
In Direct mode, the bass and treble tone circuits are
bypassed, creating a shorter signal path for a purer sound.
1
2
Press the [DIRECT] button.
Direct mode is turned on and the DIRECT indicator
lights up.
To turn off Direct mode, press the
[DIRECT] button again.
The DIRECT indicator goes off.
2
To unmute the CR-L5, press the [MUT-
ING] button again, or adjust the
remote controller’s volume [ ]/[ ]
Note: If you press the remote controller’s [TONE] button
while Direct Mode is on, Direct mode will be cancelled.
buttons.
The output is unmuted and the MUTING indicator
goes off.
Note: The Mute function is cancelled when the CR-L5 is set
to Standby.
Adjusting the Display Brightness
You can adjust the display brightness as follows.
1
Press the [DIMMER] button repeatedly
to select: dim, dimmer, or normal
brightness.
25
CR-L5_E.book Page 26 Monday, May 19, 2003 4:05 PM
Timers
About the Timers
ON
STANDBY
The CR-L5 has four timers that you can use to automatically
turn it on and off at certain times and on certain days of the
week, so you can listen to, or record your favorite programs.
Timers can be used to start and stop playback (Play), or to
start and stop radio or TV/LINE input recording (Rec) with
TONE
STANDBY
▼
1
▲
2
INPUT
TIMER
3
TIMER
ENTER
▲
▼
4
5
6
9
7
8
>
10
10/0
ENTER
an Onkyo cassette tape deck connected via
.
SLEEP
VOLUME
Timers can be set for one-off use (Once), in which case the
timer is reset once the task has been completed, for use on a
certain day every week (Every), or for a range of days (e.g.,
Monday through Friday).
UP
MUTING
DIRECT
Setting the Timers
■ Timer Examples
The timers are set using the remote controller.
You must set the clock (page 16) before you can set the tim-
ers.
To use a timer to turn on the radio, you must preset some
radio stations first (see page 22).
The following examples highlight some of the ways in
which you can use the timers.
Timer 1: To wake up to your favorite radio station (preset
#1) every morning, set as follows:
PLAY➔FM 1➔EVERY➔EVERY DAY➔ON 7:00➔OFF
7:30
If you want a radio alarm only on weekdays, select “Days
Set” instead of “Everyday” and specify “MON–FRI.”
Timer 2: To record a one-off radio program (preset #2) this
Sunday, set as follows:
1
Press the [TIMER] button repeatedly
to select Timer #1, #2, #3, or #4, and
then press the [ENTER] button.
In this example, timer #1 has been selected.
REC➔FM 2➔ONCE➔SUN➔ON 21:00➔OFF 22:00
(You need an Onkyo cassette tape deck to do the recording.)
■ Timer Overlap
If two or more timers are set to the same ON time, the timer
with the lowest number has priority. For example, if Timer
#1 and Timer #2 are both set to an ON time of 7:00, Timer
#1 has priority and Timer #2 is ignored.
Timer 1: 07:00 - 13:00 (This timer has priority.)
Timer 2: 07:00 - 12:30
2
Use the Up/Down [ ]/[ ] buttons to
select Play or Rec, and then press
[ENTER].
If the settings of two timers overlap, the earlier timer has
priority.
Timer 1: 9:00 - 10:00
OR
Timer 2: 8:00 - 10:00 (This timer has priority.)
Notes:
• The timers work only if the CR-L5 is in Standby mode. If
the CR-L5 is on when a timer is supposed to start play-
back or recording, nothing will happen, so be sure to
switch the CR-L5 to Standby mode.
• While a timed playback or recording task is in progress,
you cannot set the clock or change the specified OFF
time.
• While a timed recording task is in progress, the output of
the CR-L5 is muted. To hear what’s being recorded, press
the [MUTING] button to cancel the Mute function. Press
it again to mute the CR-L5.
3
Use the Up/Down [ ]/[ ] buttons to
select the input source, and then
press [ENTER].
For timed playback you can select any input source.
For timed recording you can select AM, FM, or TV/
LINE.
In this example, CD has been selected.
26
CR-L5_E.book Page 27 Monday, May 19, 2003 4:05 PM
Timers—Continued
If you select AM or FM, use the Up/Down [ ]/[ ]
buttons to select a preset, and then press [ENTER].
In this example, preset #2 has been selected.
6
7
Use the number buttons to enter the
ON time, and then press [ENTER].
To enter, for example, 7:29, press [10/0], [7], [2], and
[9].
4
Use the Up/Down [ ]/[ ] buttons to
select Once or Every, and then press
[ENTER].
Use the [>10] button to toggle between AM and PM for
the 12-hour format.
After the ON time has been set, the OFF time is auto-
matically set to one hour later.
Once: For one-off use.
Every: For weekly use.
Use the number buttons to enter the
OFF time, and then press [ENTER].
OR
The TIMER indicator appears, as shown.
In this example, timers #1 and #3 have been set.
5
Use the Up/Down [ ]/[ ] buttons to
select one of the following options,
and then press [ENTER].
SUN (Sunday)
FRI (Friday)
SAT (Saturday)
Everyday
MON (Monday)
TUE (Tuesday)
WED (Wednesday)
THU (Thursday)
8
Press the [STANDBY] button to set the
CR-L5 to Standby mode.
Days Set
The “Everyday” and “Days Set” (specifies a range of
days) options only appear if you select “Every” in step
4.
Notes:
• You can cancel the timer setting procedure at any time by
pressing the [TIMER] button.
• If you’re using a timer to start playback, be sure to set the
volume to a suitable level. If the VOLUME control is set
to minimum, you won’t hear anything when the timed
playback task starts.
If you select “Days Set”, use the Up/Down [ ]/[ ]
buttons to select the first day, and then press
[ENTER].
In this example, the first day is Tuesday.
• If you set the playback source to CD, don’t forget to load
a CD into the CR-L5 before setting it to Standby mode.
• If you’re using a timer to start recording on an Onkyo cas-
sette tape deck connected via
, be sure to select the
correct input source on the cassette tape deck, and load a
cassette tape before switching the CR-L5 to Standby
mode.
• For timed recording, it’s a good idea to set the start time
a little before the actual start time of the program that you
intend to record.
Use the Up/Down [ ]/[ ] buttons to select the last
day, and then press [ENTER].
In this example, the last day is Sunday.
27
CR-L5_E.book Page 28 Monday, May 19, 2003 4:05 PM
Timers—Continued
Turning Timers Off
Checking Timer Settings
You can turn timers on or off as necessary. This can be use-
ful when, for example, you’re on holiday and you don’t
want to be woken up by the timer that you normally use as
an early-morning radio alarm.
You can check a timer’s settings as follows.
1
Press the [TIMER] button repeatedly
to select the timer that you want to
check.
In this example, timer #1 is selected.
ON
STANDBY
TONE
▼
1
▲
2
INPUT
TIMER
3
TIMER
ENTER
▲
▼
4
5
6
9
7
8
>
10
10/0
ENTER
SLEEP
VOLUME
SLEEP
2
Press the [ENTER] button repeatedly
to cycle through the timer’s settings.
UP
MUTING
DIRECT
Notes:
• You can edit the selected timer’s settings as you check
them. To do this, use the Up/Down [ ]/[ ] buttons to edit
the currently displayed setting, and then press [ENTER]
to move on to the next setting.
• If the selected timer was OFF, and you edit its settings, it
will be turned ON.
1
2
Press the [TIMER] button repeatedly
to select the timer that you want to
turn off.
In this example, timer #1 is selected.
Using the Sleep Timer
With the sleep timer you can set the CR-L5 so that it auto-
matically turns off after a specified period.
Use the Up/Down [ ]/[ ] buttons to
select Timer Off.
1
Press the [SLEEP] button repeatedly
to select the required sleep time.
With the [SLEEP] button you can set the sleep time
from 90 to 10 minutes in 10 minute steps.
While the sleep time is displayed, you can use the
remote controller’s Up/Down [ ]/[ ] buttons to set the
sleep time in 1 minute steps from 99 to 1.
The timer is turned off, and the previous display reap-
pears after two seconds.
To turn a timer back on again, repeat this procedure and
use the Up/Down [ ]/[ ] buttons to select Timer On.
The SLEEP indicator appears on the display when the
sleep timer has been set, as shown. The specified sleep
time appears on the display for about five seconds, then
the previous display reappears.
SLEEP indicator
To cancel the sleep timer, press the [SLEEP] button
repeatedly until the SLEEP indicator disappears.
To check the remaining sleep time, press the
[SLEEP] button. Note that if you press the [SLEEP]
button while the sleep time is being displayed, you’ll
shorten the sleep time by 10 minutes.
28
CR-L5_E.book Page 29 Monday, May 19, 2003 4:05 PM
Troubleshooting
If you have any trouble using your CR-L5, check the following table for possible causes and remedies. If you still can’t resolve
the issue yourself, please contact your Onkyo dealer.
Trouble
Possible Cause
Remedy
Connect the power cord properly to a suitable
wall outlet (page 16).
Can’t turn on the CR-L5? The power cord is not connected properly.
Check the speaker connections and make sure
The speaker cables are not connected prop- that none of the wires are touching each other,
erly.
other connectors, or any metal parts
(page 13).
Use the SPEAKERS A/B button to select
speaker set A, B, or A+B (page 19).
The wrong speaker set is selected.
There’s no sound coming
from the speakers?
The volume is set at minimum.
The CR-L5 is muted.
Turn up the volume (page 19).
Unmute the CR-L5 (page 25).
Turn down the volume, then disconnect the
headphones (page 19).
A pair of headphones are connected.
The wrong input source is selected.
A connecting cable may be damaged.
Check the input source setting (page 19).
Check your connecting cables for signs of
damage and replace as necessary.
Check the speaker connections and make sure
Sound is coming from only The other speaker’s cable is not connected that none of the wires are touching each other,
one speaker?
properly.
other connectors, or any metal parts
(page 13).
There are no batteries in the remote
controller.
Install new batteries (page 7).
The batteries are flat.
Replace with new batteries (page 7).
Check the batteries and correct as necessary
(page 7).
The batteries are installed incorrectly.
You’re not pointing the remote controller at Point the remote controller at the CR-L5’s
the CR-L5’s remote sensor.
remote sensor (page 7).
Use the remote controller closer to the CR-L5
(page 7). The remote controller has a range of
approximately 5 meters (16 ft.).
The remote controller
doesn’t work?
You’re too far away from the CR-L5.
Make sure that the CR-L5 is not subjected to
direct sunshine or inverter-type fluorescent
lights. Relocate if necessary.
A strong light source is interfering with the
CR-L5’s remote sensor.
If the CR-L5 is installed in a cabinet with
colored glass doors, the remote controller
may not work reliably when the doors are
closed.
Open the doors, or use a cabinet without col-
ored glass.
Can’t tune into AM sta-
tions?
The supplied AM loop antenna is not con- Connect the AM loop antenna properly
nected properly.
(page 14).
AM reception is hindered
by a buzzing noise, espe-
Relocate your AM antenna.
Interference caused by electrical equip-
cially at night or with weak ment, including fluorescent lights.
signals?
Install an outdoor AM antenna (page 15).
29
CR-L5_E.book Page 30 Monday, May 19, 2003 4:05 PM
Troubleshooting—Continued
Trouble
Possible Cause
Remedy
Move the AM loop antenna as far away as
possible from your TV.
AM reception is hindered
by a high-pitched noise?
Interference caused by your TV.
Move the CR-L5 as far away as possible from
your TV.
Install an outdoor antenna as far away as pos-
sible from nearby roads.
Interference is being caused by fluorescent
lights being turned on or off, or by the igni-
tion systems of passing cars.
Reception is hindered by a
crackling noise?
Move your antenna as far away as possible
from fluorescent lights.
Adjust the position or direction of your out-
door antenna.
FM reception and stereo
separation are poor even
Tall buildings, mountains, or hills are caus-
ing wave reflections that interfere with the Try an FM antenna with better directionality.
though the Tuning and FM main signal.
STEREO indicators are
shown.
The station’s signal is too strong.
Try an indoor FM antenna.
Use the [FM MODE] button to select mono
mode (page 22).
You’re too far away from the transmitter. Or, Adjust the position, height, and direction of
your FM antenna is in the wrong position or your FM antenna.
Reception is noisy, inter-
mittent, and the FM STE-
REO indicator flickers?
pointing in the wrong direction. Or, the sta-
tion’s signal strength is poor.
Install an outdoor FM antenna, preferably one
with many elements. Installing an outdoor
antenna is a specialist job, so contact your
nearest dealer for advice (page 15).
Preset your favorite radio stations again
The power cord has not been connected to a
(page 22). The power cord must be plugged
wall outlet, or the power has been turned off
into a wall outlet a few times each month in
for an extended period.
The radio presets no longer
work?
order to preserve the presets (page 4).
The current FM station does not support
RDS.
Tune into a station that supports RDS
(page 23).
The RDS (Radio Data Sys-
tem) doesn’t seem to work?
Install an outdoor FM antenna (page 15),
change the position or direction of your out-
door FM antenna, and keep it away from flu-
orescent lights.
The signal strength is poor, or there’s too
much interference.
Install the CR-L5 somewhere free of vibra-
tion.
The CR-L5 is subject to vibration.
CD playback skips?
The disc is dirty.
Remove the disc and clean it (page 6).
Buy a new disc.
The disc is very scratched.
No disc is loaded.
Load a disc (page 20).
Can’t enter track numbers
for memory playback?
The track number entered doesn’t exist on
the disc.
Enter the correct track number (page 21).
Load the disc with the label-side facing up
(page 20).
The disc is upside down.
The disc is dirty.
Remove the disc and clean it (page 6).
Can’t play a CD?
Remove the disc and leave the CR-L5 turned
Condensation has formed inside the CR-L5. on for several hours until the condensation
has evaporated.
30
CR-L5_E.book Page 31 Monday, May 19, 2003 4:05 PM
Troubleshooting—Continued
Trouble
Possible Cause
Remedy
Remove the disc and clean it (page 6).
Buy a new disc.
The disc is dirty.
It takes a long time to locate
certain tracks?
The disc is very scratched.
CT (Clock Time) information has been
taken from a radio station in another time
zone.
Set ACCUCLOCK to use a specific station
(page 17).
The clock is wrong?
This is not a malfunction. The CR-L5 will
turn itself off automatically when the ACCU-
CLOCK function has updated the clock.
The CR-L5 turns itself on
unexpectedly?
TheACCUCLOCK function is updating the
clock.
Set the CR-L5 to Standby (page 27). The CR-
L5 must be in Standby mode, otherwise the
timed task will not work.
The CR-L5 was already on at the specified
ON time.
The timer didn’t work?
The specified ON time coincided, or over- Check the timer settings and correct as neces-
lapped the ON time of another timer.
sary (page 28).
To hear what’s being recorded, press the
[MUTING] button to cancel the Mute func-
tion. Press it again to mute the CR-L5.
While a timed recording task is in progress,
the output of the CR-L5 is muted.
No sound is output when a
timed playback or record-
ing task starts?
For timed playback, the volume is deter-
mined by the VOLUME control.
Set the volume to a suitable level (page 19).
Abnormal Behavior
The CR-L5 contains a microcomputer for signal processing and control functions. In very rare situations, severe interfer-
ence, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should happen,
unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.
Restoring the Default Settings
To reset the CR-L5 to its factory defaults, turn it on and, while holding down the STOP [ ] button, press the [STANDBY/
ON] button. Press the [STANDBY/ON] button again. “Initialized” appears on the display and the CR-L5 is reset to its
factory defaults.
31
CR-L5_E.book Page 32 Monday, May 19, 2003 4:05 PM
Specifications
50 dB quieting sensitivity
AMPLIFIER
Power output:
FM:
Mono
17.2 dBf, 2.0 µV (75 Ω)
2 × 50 watts at 4 Ω 1 kHz DIN
Stereo 37.2 dBf, 20.0 µV (75 Ω)
2 × 41 watts at 6 Ω 1 kHz DIN
2 × 35 watts at 8 Ω 1 kHz DIN
2 × 62 watts at 4 Ω
Capture ratio
FM:
2.0 dB
Dynamic power:
Image rejection ratio
2 × 40 watts at 8 Ω
FM:
AM:
85 dB
40 dB
Total harmonic distortion:
0.2% at 25 watts output
0.2% at 25 watts output
50 at 8 Ω
IF rejection ratio
FM:
IM distortion:
Damping factor:
Sensitivity and impedance
TV/LINE, CDR Play,
TAPE Play: 200 mV, 50 kΩ
Frequency response: 10 to 100,000 Hz, +0 / –3 dB
Tone control
BASS:
TREBLE:
Signal to noise ratio: 100 dB (IHF A)
Muting
90 dB
40 dB
AM:
Signal to noise ratio
FM:
Mono
73 dB, IHF
Stereo 67 dB, IHF
40 dB
AM:
Selectivity
FM:
50 Hz 8 dB
10 kHz 7 dB
50 dB DIN
( 300 kHz at 40 kHz Devi.)
AM suppression ratio: 50 dB
Harmonic distortion
–50 dB
FM:
Mono
Stereo 0.3%
0.7%
0.2%
CD PLAYER
Signal readout system: Optical non–contact
Reading rotation:
AM:
Frequency response
FM:
Stereo separation
FM:
About 500 – 200 r.p.m.
(constant linear velocity)
1.2 – 1.4 m / s
30 to 15,000 Hz ( 1.5 dB)
Linear velocity:
Error correction system:
35 dB at 1,000 Hz
25 dB at 100 to 10,000 Hz
Cross Interleave Read Solomon code
multi-bit sigma delta modulation
352.8 kHz 8 times over sampling
D / A converter:
Digital filter:
Number of channels: 2 (stereo)
Stereo threshold
FM:
17.2 dBf, 2.0 µV (75 Ω)
GENERAL
Frequency response: 5 to 20,000 Hz
Power supply:
AC 230-240 V, 50 Hz
Wow and flutter;
Below threshold of measurability
Power consumption: 130 W
(1.5 W in Standby, 15 W with clock)
Dimensions (W × H × D):
TUNER
Tuning range
FM:
AM:
Usable sensitivity
FM:
87.5 to 108.00 MHz (50 kHz steps)
522 to 1611 kHz (9 kHz steps)
435 × 81.5 × 382 mm
17-1/8 × 3-3/16 × 15-1/16 (inches)
Weight:
6.8 kg (15.1 lbs.)
Mono
11.2 dBf,
1.0 µV (75 Ω IHF)
Specifications and features are subject to change without
notice.
0.9 µV (75 Ω DIN)
Stereo 17.2 dBf,
2.0 µV (75 Ω IHF)
23.0 µV (75 Ω DIN)
AM:
30 µV
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO CHINA LIMITED
Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
HOMEPAGE
SN 29343526
Printed in Japan
I0305-1
(C) Copyright 2003 ONKYO CORPORATION Japan. All rights reserved.
|