Nokia 7270 User Manual

User Guide for Nokia 7270

9231145

Issue 1

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and

improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special,

incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of

any kind, either express or implied, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or

contents of this document. Nokia reserves the right to revise this document or withdraw it at any time

without prior notice.

The availability of particular products may vary by region. Please check with the Nokia dealer nearest to

you.

9231145 / Issue 1

Contents

FOR YOUR SAFETY ............................................................................................ 12

General information.......................................................................................... 16

Access codes .............................................................................................................................................. 16

Configuration settings service.............................................................................................................. 18

1. Getting started .............................................................................................. 19

Opening the fold....................................................................................................................................... 19

The wraps of the phone.......................................................................................................................... 20

Maintaining the textile wraps........................................................................................................... 20

Installing the battery and the SIM card............................................................................................. 21

Attaching the wrist strap....................................................................................................................... 23

Charging the battery ............................................................................................................................... 24

Switching the phone on and off .......................................................................................................... 25

2. Your phone..................................................................................................... 27

Introduction to the phone - fold closed............................................................................................ 27

Introduction to the phone - fold open............................................................................................... 29

Standby mode............................................................................................................................................ 30

Mini display ............................................................................................................................................ 30

Main display........................................................................................................................................... 31

Wallpaper............................................................................................................................................. 32

Screen saver........................................................................................................................................ 32

Essential indicators in standby mode .......................................................................................... 33

Some shortcuts in standby mode..................................................................................................... 35

Keypad lock (Keyguard) .......................................................................................................................... 36

3. Call functions ................................................................................................ 37

Making a call ............................................................................................................................................. 37

Making a call using contacts............................................................................................................. 37

Speed dialing.......................................................................................................................................... 37

Answering or rejecting a call................................................................................................................ 38

Options during a call............................................................................................................................... 39

4. Writing text................................................................................................... 41

Setting predictive text input on and off............................................................................................ 41

Selecting the writing language............................................................................................................ 41

Using predictive text input.................................................................................................................... 42

Writing compound words................................................................................................................... 42

Using traditional text input................................................................................................................... 43

Tips for writing text................................................................................................................................. 43

5. Using the menu ............................................................................................. 45

Accessing a menu function ................................................................................................................... 45

List of menu functions............................................................................................................................ 47

6. Menu functions............................................................................................. 52

Messages..................................................................................................................................................... 52

Text messages (SMS)............................................................................................................................ 52

Writing and sending SMS messages............................................................................................ 53

Options for sending a message...................................................................................................... 53

Reading and replying to an SMS message................................................................................. 54

Templates............................................................................................................................................. 54

Multimedia messages .......................................................................................................................... 55

Writing and sending a multimedia message ............................................................................. 55

Reading and replying to a multimedia message ...................................................................... 57

Multimedia messages memory full.................................................................................................. 59

Inbox, Outbox, Saved items and Sent items folders ................................................................... 59

Instant messages................................................................................................................................... 60

Entering the instant messaging menu......................................................................................... 61

Connecting to and disconnecting from the instant messaging service............................. 62

Starting an instant messaging conversation............................................................................. 62

Accepting or rejecting an instant messaging invitation........................................................ 64

Reading a received instant message............................................................................................ 64

Participating in an instant messaging conversation............................................................... 65

Editing your own settings............................................................................................................... 65

Contacts for instant messaging .................................................................................................... 66

Blocking and unblocking messages.............................................................................................. 66

Groups................................................................................................................................................... 67

E-mail messages.................................................................................................................................... 67

Writing and sending an e-mail...................................................................................................... 68

Downloading e-mail messages...................................................................................................... 69

Reading and replying to an e-mail message ............................................................................. 70

Inbox and Other folders................................................................................................................... 70

Deleting e-mail messages............................................................................................................... 71

Voice messages...................................................................................................................................... 71

Info messages......................................................................................................................................... 71

Service commands................................................................................................................................ 71

Deleting messages ................................................................................................................................ 72

Message settings................................................................................................................................... 72

Settings for text messages.............................................................................................................. 72

Settings for multimedia messages ............................................................................................... 73

Settings for e-mail application ..................................................................................................... 75

Other settings..................................................................................................................................... 76

Message counter................................................................................................................................... 76

Contacts...................................................................................................................................................... 76

Searching for a contact....................................................................................................................... 77

Saving names and phone numbers (Add contact)....................................................................... 77

Saving multiple numbers or text items per name....................................................................... 77

Adding an image to a contact........................................................................................................... 79

Editing or deleting details in the contacts .................................................................................... 79

Deleting contacts.................................................................................................................................. 80

Presence-enhanced contacts - My presence................................................................................ 80

Presence-enhanced contacts - Subscribed names...................................................................... 82

Adding contacts to the subscribed names ................................................................................. 82

Viewing the subscribed names ...................................................................................................... 83

Unsubscribing a contact.................................................................................................................. 83

Copying contacts................................................................................................................................... 83

Settings for contacts............................................................................................................................ 84

Sending and receiving a business card........................................................................................... 84

Voice dialing........................................................................................................................................... 85

Adding and managing voice tags.................................................................................................. 85

Making a call by using a voice tag............................................................................................... 86

Other functions in the Contacts....................................................................................................... 86

Call register................................................................................................................................................ 87

Recent calls lists.................................................................................................................................... 87

Call counters and call timers............................................................................................................. 88

Message counter................................................................................................................................... 88

Positioning.............................................................................................................................................. 89

Settings...................................................................................................................................................... 89

Profiles ..................................................................................................................................................... 89

Themes ..................................................................................................................................................... 90

Tone settings .......................................................................................................................................... 90

Main display settings........................................................................................................................... 91

Mini display settings............................................................................................................................ 91

Time and date settings........................................................................................................................ 92

Personal shortcuts ................................................................................................................................ 93

Connectivity............................................................................................................................................ 93

Infrared................................................................................................................................................. 93

GPRS...................................................................................................................................................... 94

GPRS connection ............................................................................................................................... 95

GPRS modem settings...................................................................................................................... 96

Call settings............................................................................................................................................ 96

Phone settings ....................................................................................................................................... 98

Enhancement settings......................................................................................................................... 99

Configuration settings......................................................................................................................... 99

Security settings................................................................................................................................. 101

Restore factory settings................................................................................................................... 102

Gallery....................................................................................................................................................... 102

Media........................................................................................................................................................ 104

Camera.................................................................................................................................................. 104

Taking a photo................................................................................................................................. 104

Recording a video clip................................................................................................................... 105

Camera settings .............................................................................................................................. 105

Media player........................................................................................................................................ 105

Setting up the phone for a streaming service........................................................................ 106

Radio...................................................................................................................................................... 106

Tuning a radio channel ................................................................................................................. 107

Using the loudspeaker................................................................................................................... 107

Voice recorder..................................................................................................................................... 108

Recording.......................................................................................................................................... 108

Push to talk ............................................................................................................................................. 109

Opening the push to talk menu..................................................................................................... 110

Connecting to and disconnecting from the push to talk service......................................... 110

Callback requests ............................................................................................................................... 111

Making and receiving a push to talk call.................................................................................... 112

Making a group call....................................................................................................................... 113

Making a one-to-one call............................................................................................................ 113

Receiving a group or a one-to-one call................................................................................... 114

Adding one-to-one contact............................................................................................................ 114

Creating and setting up groups..................................................................................................... 115

Settings for push to talk.................................................................................................................. 117

Organiser.................................................................................................................................................. 118

Alarm clock.......................................................................................................................................... 118

When the alarm time expires...................................................................................................... 119

Calendar................................................................................................................................................ 120

Note alarm........................................................................................................................................ 121

To-do list .............................................................................................................................................. 121

Notes...................................................................................................................................................... 121

Synchronisation.................................................................................................................................. 122

Synchronising from your phone................................................................................................. 123

Settings for synchronisation ....................................................................................................... 123

Synchronising from a compatible PC........................................................................................ 124

Wallet.................................................................................................................................................... 124

Accessing the wallet menu.......................................................................................................... 125

Saving card details......................................................................................................................... 126

Personal notes ................................................................................................................................. 126

Creating a wallet profile............................................................................................................... 127

Wallet settings ................................................................................................................................ 127

Calculator............................................................................................................................................. 127

Performing a currency conversion............................................................................................. 128

Stopwatch............................................................................................................................................ 128

Countdown timer............................................................................................................................... 129

Applications ............................................................................................................................................ 130

Games.................................................................................................................................................... 130

Collection ............................................................................................................................................. 130

Options available for an application......................................................................................... 131

Downloading a game or an application................................................................................... 131

Web ........................................................................................................................................................... 132

Basic steps for accessing and using services............................................................................. 133

Setting up browsing.......................................................................................................................... 133

Connecting to a service.................................................................................................................... 133

Browsing the pages........................................................................................................................... 134

Browsing with phone keys........................................................................................................... 135

Options while browsing................................................................................................................ 135

Direct calling.................................................................................................................................... 136

Quit browsing...................................................................................................................................... 136

Appearance settings of the browser............................................................................................. 136

Bookmarks............................................................................................................................................ 137

Receiving a bookmark................................................................................................................... 137

Downloading ....................................................................................................................................... 138

Service inbox....................................................................................................................................... 138

Service inbox settings ................................................................................................................... 138

The cache memory............................................................................................................................. 139

Cookies.................................................................................................................................................. 139

Scripts over secure connection...................................................................................................... 140

Browser security................................................................................................................................. 140

Security module.............................................................................................................................. 140

Certificates ....................................................................................................................................... 141

Digital signature ............................................................................................................................. 142

SIM services ............................................................................................................................................ 143

7. PC Connectivity ........................................................................................... 144

Using data communication applications........................................................................................ 144

8. Battery information..................................................................................... 145

Charging and Discharging................................................................................................................... 145

9. Enhancements.............................................................................................. 147

CARE AND MAINTENANCE............................................................................. 148

ADDITIONAL SAFETY INFORMATION............................................................. 150

FOR YOUR SAFETY

Read these simple guidelines. Not following them may be dangerous or illegal. Read the

complete user guide for further information.

SWITCH ON SAFELY

Do not switch the phone on when wireless phone use is prohibited or when it

may cause interference or danger.

ROAD SAFETY COMES FIRST

Obey all local laws. Always keep your hands free to operate the vehicle while

driving. Your first consideration while driving should be road safety.

INTERFERENCE

All wireless phones may be susceptible to interference, which could affect

performance.

SWITCH OFF IN HOSPITALS

Follow any restrictions. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Don't use the phone at a refuelling point. Don't use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Follow any restrictions. Don't use the phone where blasting is in progress.

USE SENSIBLY

Use only in the normal position as explained in the product documentation.

Don't touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES

Use only approved enhancements and batteries. Do not connect incompatible

products.

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

BACK-UP COPIES

Remember to make back-up copies or keep a written record of all important

information stored in your phone.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user guide for detailed safety

instructions. Do not connect incompatible products.

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press

as many times as

needed to clear the display and return to the start screen. Key in the emergency

number, then press the call key

until given permission to do so.

. Give your location. Do not end the call

■ ABOUT YOUR DEVICE

The wireless device described in this guide is approved for use on the EGSM900, GSM1800

and GSM1900 network. Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect privacy and legitimate

rights of others.

Warning: To use any features in this device, other than the alarm clock, the device

must be switched on. Do not switch the device on when wireless device use may

cause interference or danger.

Your device and its enhancements may contain small parts. Keep them out of reach of small

children.

For availability of approved enhancements, please check with your dealer. When you

disconnect the power cord of any enhancement, grasp and pull the plug, not the cord.

■ Network Services

To use the phone you must have service from a wireless service provider. Many of the

features in this device depend on features in the wireless network to function. These

Network Services may not be available on all networks or you may have to make specific

arrangements with your service provider before you can utilize Network Services. Your

service provider may need to give you additional instructions for their use and explain what

charges will apply. Some networks may have limitations that affect how you can use

Network Services. For instance, some networks may not support all language-dependent

characters and services.

Your service provider may have requested that certain features be disabled or not activated

in your device. If so, they will not appear on your device menu. Contact your service provider

for more information.

This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some

features of this device, such as multimedia messaging service (MMS), browsing, instant

messaging, e-mail, presence-enhanced contacts, and remote synchronisation, content

downloading using browser or MMS, require network support for these technologies.

■ SHARED MEMORY

The phone has three different memories. The following features in this device may share the

first memory: contacts, text messages, instant messages and SMS e-mails, voice tags,

calendar and notes. The second shared memory is used by multimedia messages, files stored

in Gallery and configuration settings. The third shared memory is used by e-mail application,

Java games and applications. Use of one or more of these features may reduce the memory

available for the remaining features sharing the same memory. For example, saving many

Gallery items may use all of the available memory in the second memory. Your device may

display a message that the memory is full when you try to use a shared memory feature. In

this case, delete some of the information or entries stored in the corresponding shared

memory before continuing.

■ Nokia support on the Web

Check <www.nokia.com/support> or your local Nokia Web site for the latest version of this

guide, additional information, downloads, and services related to your Nokia product.

General information

■ Access codes

• Security code (5 to 10 digits): The security code helps to protect your phone

against unauthorised use. The preset code is 12345. Change the code, and keep

the new code confidential and in a safe place separate from your phone. You

can set the phone to request the code, see Security settings on page 101.

If you key in an incorrect security code five times in succession, the phone

ignores further entries of the code. Wait for 5 minutes, and key in the code

again.

• PIN and PIN2 codes (4 to 8 digits):

The PIN (Personal Identification Number) code helps to protect your SIM card

against unauthorised use. The PIN code is usually supplied with the SIM card.

You can set the phone to request the PIN code each time the phone is switched

on, see Security settings on page 101.

The PIN2 code may be supplied with the SIM card and is required to access

some functions.

• Module PIN and signing PIN:

The module PIN is required to access the information in the security module,

see Security module on page 140.

The signing PIN is required for the digital signature, see Digital signature on

page 142. The module and signing PIN are supplied with the SIM card if the

SIM card has a security module in it.

If you key in an incorrect PIN code three times in succession, the phone may

display PIN blocked or PIN code blocked, for example, and ask you to enter the

PUK code.

• PUK and PUK2 codes (8 digits): The PUK (Personal Unblocking Key) or PUK2

code is required to change a blocked PIN code or PIN2 code.

If the codes are not supplied with the SIM card, contact your local service

provider for the codes.

• Barring password (4 digits): The barring password is required when using the

Call barring service, see Security settings on page 101. You can obtain the

password from your service provider.

• Wallet code (4 to 10 digits): The wallet code is required to access the wallet

services, see Wallet on page 124. If you key in an incorrect wallet code three

times, the wallet application is blocked for 5 minutes. After the next three

incorrect attempts, the length of time for which the application is blocked will

be doubled.

■ Configuration settings service

In order to use multimedia and instant messaging, and other wireless services, you

need to have the proper configuration settings on your phone. You may receive

the settings directly as a configuration message, and you need to save the settings

on your phone. For more information on the availability of the settings, contact

your network operator, service provider or nearest authorised Nokia dealer.

You may receive the configuration settings for multimedia messages, instant

messaging and presence, push to talk, e-mail application, synchronisation,

streaming, and for the browser.

When you have received the settings as a configuration message, and the settings

are not automatically saved and activated, Configuration sett. received is

displayed.

To view the received settings, press Show.

• To save the settings, press Save. If the phone requests Enter settings’ PIN:, key

in the PIN code for the settings, and press OK. To receive the PIN code, contact

the service provider that supplies the settings.

If no settings are saved yet, these settings are saved and set as default

configuration settings. Otherwise, the phone asks Set as default settings?.

• To discard the received settings, press Discard.

1. Getting started

■ Opening the fold

When you open the fold of the phone, it

opens up to approximately 150 degrees. Do

not try to force the fold open more.

■ The wraps of the phone

You can personalise your phone with replaceable textile wraps.

To insert a wrap, fasten it on the phone according to the picture.

To remove the wrap, first loosen it from both sides of the hinge (1), then from the

ends of the phone (2).

Maintaining the textile wraps

You can dust the textile wrap daily using a soft brush or a dry cloth.

To clean the textile wrap, remove the wrap and run a slightly damp white cotton

cloth over them. Avoid the use of printed absorbent cloths/papers as they can

release ink onto the textile.

To clean the wrap more thoroughly, remove the wrap from the phone and dust it

with care. You can wash the wrap with water at approximately 30°C and a mild

detergent. Do not spin-dry. Always let the wrap dry thoroughly before attaching it

to the phone. Brush it delicately with a soft bristle brush.

■ Installing the battery and the SIM card

Keep all SIM cards out of the reach of small children. For availability and information on

using SIM card services, contact your SIM card vendor. This may be the service provider,

network operator, or other vendor.

Always switch the device off and disconnect the charger before removing the battery.

1. With the phone fold closed and the back of the phone

facing you, press the release button, and lift the

cover to remove it from the phone (1).

2. Lift out the battery (2).

3. To release the SIM card holder, gently pull the locking

clip, and open the holder (3). Insert the SIM card into the SIM card holder so

that the golden contact area on the card is facing downwards (4). Ensure that

the SIM card is properly inserted. Close the cover of the SIM card holder (5),

and press it gently to snap into place.

4. Replace the battery (6).

5. Place first the locking catches in the cover to the

locking catches on the phone (7), then press the

other end of the cover into place (8).

■ Attaching the wrist strap

Remove the cover from the phone. See step 1 in Installing the battery and the SIM

card on page 21.

Thread the strap as shown in the

picture.

Close the cover. See step 5 in

Installing the battery and the SIM

card on page 21.

■ Charging the battery

Warning: Use only batteries, chargers, and enhancements approved by Nokia for

use with this particular model. The use of any other types may invalidate any

approval or warranty, and may be dangerous.

Check the model number of any charger before use with this device. This device is

intended for use when supplied with power from ACP-12, ACP-7, AC-1, and LCH-

12.

1. Connect the lead from the charger to the socket

on the bottom of your phone.

2. Connect the charger to an AC wall socket.

The battery indicator scrolls during charging,

and when the power is on, Charging is displayed

briefly when the charging starts. If the battery is

completely discharged, it may take a few

minutes before the charging indicator appears

on the display or before any calls can be made.

You can use the phone while the charger is connected.

The charging time depends on the charger and the battery used. For example,

charging a BL-4C battery with the AC-1 charger takes approximately 1 hour and

30 minutes while the phone is in standby mode.

■ Switching the phone on and off

To switch the phone on or off, press and hold the

power key.

If the phone displays Insert SIM card even though

the SIM card is properly inserted, or SIM card not

supported, contact your network operator or

service provider.

If the phone requests a PIN code or a security

code, open the fold, key in the code, and press OK.

See also Access codes on page 16.

Your device has an internal antenna.

Note: As with any other radio transmitting device, do not

touch the antenna unnecessarily when the device is

switched on. Contact with the antenna affects call quality

and may cause the device to operate at a higher power

level than otherwise needed. Avoiding contact with the

antenna area when operating the device optimises the

antenna performance and the battery life.

Hold the phone in the normal position.

2. Your phone

■ Introduction to the phone - fold closed

1. Mini display

2. Loudspeaker

3. Charger connector

4. Microphone

5. Pop-Port^TMconnector

used, for example, for

headsets and the data

cable.

6. Camera lense

7. Power key switches the

phone on and off.

To turn the display lights on for approximately 15 seconds when the keypad is

locked, press the power key briefly.

When the keypad is not locked, you can change the profiles; to access the

profiles and to scroll through them, press the power key briefly, and to activate

a profile, press and hold the power key. See Profiles on page 89.

8. Infrared (IR) port

9. Push to talk key to make a push to talk call. See Making and receiving a push

to talk call on page 112.

■ Introduction to the phone - fold open

1. Ear piece

2. Main display

3. Left selection key

middle selection key

right selection key

The function of these keys depends on the

guiding text shown on the display above the

keys. See Standby mode on page 30.

ends an active call.

Press and hold to exit from any function.

enter numbers and characters.

are used for various purposes in

and

different functions.

6. 4-way scroll key:

up, down, left, right

Enables, for example, scrolling through contacts, menus or settings, in

calendar, or moving the cursor when writing text.

7. Call key

dials a phone number, and answers a call.

8. Volume keys to adjust the volume of the earpiece or the loudspeaker, or the

headset when it is connected to the phone.

When the fold is closed, to mute the ringing tone of an incoming call, to switch

the alarm clock to snooze, or to mute, for example, the calendar note alarm.

■ Standby mode

When the phone is ready for use, and you have not keyed in any characters, the

phone is in standby mode.

Mini display

When the fold is closed, the mini display may show the following:

• The signal strength of the cellular network at your current location and the

battery charge level. Refer to Main display on page 31.

• The name of the network, or if the phone is not in service, it is indicated by a

text note.

• The time and date, the active profile and the alarm clock or calendar note

alerts.

• When you have an incoming call, the caller’s name or number is shown if it is

identified. Refer to Answering or rejecting a call on page 38.

Main display

1. Shows the name of the network or the operator

logo to indicate in which cellular network the

phone is currently being used.

2. Shows the signal strength of the cellular network

at your current location. The higher the bar, the

stronger the signal.

3. Shows the battery charge level. The higher the

bar, the more power in the battery.

4. The left selection key

in standby mode is Go

to. You can use the key as a shortcut to your

favourite functions.

To view the list of functions that you have on

your personal shortcut list, press Go to. To activate a function, scroll to it, and

press Select.

• To add more functions to the shortcut list, press Options, and select Select

options. Scroll to a function, and press Mark to add it to the shortcut list. To

remove a function from the list, press Unmark.

If there are no functions on the shortcut list, press Add to add a function.

• To arrange the functions on the list, press Options, and select Organise.

Scroll to the function that you want to move, press Move, and select where

you want to move the function.

5. The middle selection key

in standby mode is Menu.

6. The right selection key

in standby mode may be Names to access the

Contacts menu, an operator-specific key to access an operator’s homepage, or

a specific function that you have selected in the Right selection key menu. See

Personal shortcuts on page 93.

Wallpaper

You can set your phone to display a background picture (wallpaper) for the main

and mini displays in standby mode.

Screen saver

You can select an image for the screen saver on mini display and set the phone to

activate it after a certain length of time if no phone function is used. See Screen

saver in Mini display settings on page 91.

The phone automatically activates the digital clock screen saver on main display

in standby mode, and also on mini display. If you have not set the time, 00:00 is

displayed.

Essential indicators in standby mode

You have received one or more text or picture messages.

You have received one or more multimedia messages.

The phone has registered a missed call.

Your phone is connected to the instant messaging service, and the

availability status is online or offline.

You have received one or more instant messages, and you are connected

to the instant messaging service.

The phone keypad is locked.

The phone does not ring for an incoming call or text message when

Incoming call alert is set to Off, and/or none of the caller groups has been

set to alert in the Alert for setting, and Message alert tone is set to Off.

The alarm clock is set to On.

The timer is running.

The stopwatch is running in the background.

The (E)GPRS connection mode Always online is selected and the (E)GPRS

service is available.

An (E)GPRS connection is established.

The (E)GPRS connection is suspended (on hold), for example if there is an

incoming or outgoing call during an (E)GPRS dial-up connection.

The infrared connection indicator is shown continuously when the IR

connection is activated.

If you have two phone lines, the indicator displays the selected phone line.

All incoming calls are diverted to another number, Divert all voice calls. If

you have two phone lines, the divert indicator for the first line is

and

for the second line

The loudspeaker is activated.

Calls are limited to a closed user group.

A headset, handsfree, loopset, or music stand is connected to the phone.

The timed profile is selected.

Push to talk connection is active or suspended.

Time and date

See Time and date settings on page 92.

Some shortcuts in standby mode

• To access the list of dialled numbers, press the left selection key

Scroll to the number or name that you want, and press the call key

the number.

once.

to call

• To call your voice mailbox (network service) when you have saved your voice

mailbox number in the phone, press and hold

• To make a connection to a browser service, press and hold

• To access the Nokia.com page, press and hold

• To open the push to talk Group list (network service), press the scroll key right.

• To find a contact name, press the scroll key down.

• To start writing text messages quickly, press the scroll key left.

• To open the camera viewfinder in standard photo view, press the scroll key up.

To quickly change the camera mode, for example video, press and hold the

scroll key left or the scroll key right.

• To change the profile, open the list of profiles and scroll to the desired profile

by briefly pressing the power key. To activate the profile, press Select.

■ Keypad lock (Keyguard)

The keyguard disables the keys to prevent them from being accidentally pressed.

• To lock the keypad in standby mode, press Menu and

within 1.5 seconds.

The keyguard is not activated when you close the fold.

• To unlock the keypad, open the fold, press Unlock and

within 1.5 seconds.

To answer a call when the keyguard is on, open the fold, or press the call key

During a call, the phone can be operated normally. When you end or reject the

call, the keyguard will automatically be on again.

For security keypad locking, see Security keyguard in the Phone settings section on

page 98.

For locking the keypad during a call, see Options during a call on page 39.

When the keyguard is on, calls still may be possible to the official emergency number

programmed into your device. Key in the emergency number and press the call key

3. Call functions

■ Making a call

1. Open the fold and key in the phone number, including the area code. If you key

in an incorrect character, press Clear to delete it.

For international calls, press

twice for the international prefix (the +

character replaces the international access code), and then key in the country

code, the area code without the leading 0, if necessary, and the phone

number.

2. To call the number, press the call key

3. To end the call or to cancel the call attempt, press

or close the fold.

Making a call using contacts

To search for a name or phone number that you have saved in Contacts, press the

scroll key down in standby mode. Scroll to the name or phone number, and to call

the number, press the call key

Speed dialing

Before you can use speed dialing, assign a phone number to one of the speed-

dialing keys, from to . See Speed dials in Other functions in the

Contacts on page 86. Call the number in one of the following ways:

• Press the speed-dialing key that you want, and press the call key

• If Speed dialling is set to on, press and hold a speed-dialing key until the call is

started. You can switch the Speed dialling On or Off. See Call settings on page

96.

■ Answering or rejecting a call

To answer an incoming call when the fold is closed, open the fold. To reject an

incoming call when the fold is closed, open the fold, and within 1.5 seconds, close

it again, or press

• If you press either of the volume keys instead of answering the call, only the

ringing tone is muted.

To answer an incoming call when you have set Answer when fold is opened to Off,

open the fold, and press the call key

To answer an incoming call when the fold is open, press the call key

reject an incoming call, press

. Refer to Call settings on page 96.

, or to

• If you press Options instead of answering the call, the ringing tone is muted,

and you can answer or reject the call.

• If you press Silence, only the ringing tone is muted. You can answer or reject

the call.

To end the call, press

, or close the fold.

If a compatible headset supplied with the headset key is connected to the phone,

you can answer and end a call by pressing the headset key.

When somebody is calling you, the phone shows the caller’s name, phone number,

or the text Private number or Call. If you receive a call from someone whose phone

number has the seven last digits as a contact saved in Contacts, the information

may not be displayed correctly.

■ Options during a call

Many of the options that you can select during a call are network services. To

check availability, contact your network operator or service provider.

During a call, press Options to select from the following:

•

Mute or Unmute, End call, End all calls, Contacts, Menu and Hold or Unhold,

Lock keypad, Record, New call (network service), Answer and Reject.

•

Conference to make a conference call that allows up to five persons to

participate (network service). During a call, make a call to a new participant

(New call). The first call is put on hold. When the new call is answered, select

Conference to include the first participant in the conference call. To have a

private conversation with one of the participants, select Private call, and select

the desired participant. To rejoin the conference call, select Add to conference.

•

Send DTMF to send DTMF (Dual Tone Multi-Frequency) tone strings, for

example, passwords or bank account numbers. The DTMF system is used by all

touch-tone telephones. You can key in the wait character w and the pause

character p by repeatedly pressing

Swap to switch between the active call and the call on hold (network service),

Transfer to connect a call on hold to an active call, and disconnect yourself

from the calls (network service).

•

Loudspeaker to use your phone as a loudspeaker during a call. The loudspeaker

is automatically deactivated when you end the call or call attempt or connect

the handsfree unit or headset to the phone.

When you have activated the loudspeaker, you can also close the fold of the

phone during a call. First press Options, and then close the fold within 5

seconds.

Warning: Do not hold the device near your ear when the loudspeaker is in use,

because the volume may be extremely loud.

4. Writing text

You can key in text, for example, when writing messages, using traditional or

predictive text input.

When you write text,

predictive text input, and

appears at the top of the display, indicating the

appears, indicating the traditional text input.

, or

case. To change the character case, press

change from letter to number mode, press and hold

mode. To revert to letter mode, press and hold

appears next to the text input indicator, indicating the character

indicates number mode. To

, and select Number

■ Setting predictive text input on and off

When you write text, press Options. To set the predictive text input on if it is

available for the language, select Dictionary on, or to revert to traditional text

input, select Dictionary off.

Tip: To quickly set the predictive text input on or off when writing text in

letter mode, press

twice, or press and hold Options.

■ Selecting the writing language

When you write text in letter mode, press Options, or press and hold

. To

temporarily change the language for writing text, select Writing language.

To set different language for writing text and for the texts shown on the display,

press Menu, and select Settings, Phone settings, and Language settings.

■ Using predictive text input

The predictive text input is based on a built-in dictionary to which you can also

add new words. You can key in a letter with a single keypress.

1. Start writing a word using the keys

. Press each key only once

for an individual letter. The word changes after each keystroke.

2. When you have finished writing the word and it is correct, confirm it by adding

a space with

or by pressing any of the scroll keys. Press a scroll key to

move the cursor.

If the word is not correct, press

repeatedly; or press Options, select

Matches, and scroll through the list of words. When the word that you want

appears, confirm it.

If the ? character is displayed after the word, the word that you intended to

write is not in the dictionary. To add the word to the dictionary, press Spell, key

in the word (traditional text input is used), and press Save. When the

dictionary is full, the new word replaces the oldest one that was added.

Writing compound words

Key in the first part of the word, and to confirm it, press the scroll key right. Write

the last part of the word, and confirm the word.

■ Using traditional text input

Press a number key,

, repeatedly until the desired character

appears. Not all characters available under a number key are printed on the key.

The characters available depend on the language selected for writing text.

• If the next letter that you want is located on the same key as the present one,

wait until the cursor appears, or press any of the scroll keys, and key in the

letter.

•

The most common punctuation marks and special characters are available

under the number key

■ Tips for writing text

The following functions may also be available for writing text:

• To insert a space, press

• To insert a number while in letter mode, press and hold the desired number key.

• To move the cursor to the left, right, down, or up, press the corresponding scroll

key.

• To delete a character to the left of the cursor, press Clear. Press and hold Clear

to delete the characters more quickly.

To delete all the characters at once when writing a message, press Optionsand

select Clear text.

• To insert a word when using the predictive text input, press Options, and select

Insert word. Write the word using the traditional text input, and press Save.

The word is also added to the dictionary.

• To insert a special character when using the traditional text input, press

When using the predictive text input, press and hold , or press Options,

and select Insert symbol. To insert a smiley when using traditional text input,

press twice. When using predictive text input, press and hold for

special characters, and press once again for smileys. Scroll to a character and

press Use to select it.

The following options are available when writing text messages:

• To insert a number while in letter mode, press Options, and select Insert

number. Key in the phone number, or search for it in Contacts, and press OK.

• To insert a name from Contacts, press Options, and select Insert contact. To

insert a phone number or a text item attached to the name, press Options, and

select View details.

5. Using the menu

The phone offers you an extensive range of functions that are grouped into

menus. Most of the menu functions are provided with a brief help text. To view

the help text, scroll to the menu function that you want and wait for 15 seconds.

To exit the help text, press Back. You can set the phone to display or hide the

menu help texts in the Help text activation menu. See Phone settings on page 98.

■ Accessing a menu function

By scrolling

1. To access the menu, press Menu.

2. Scroll up or down through the menu list, or scroll with any of the scroll keys if

the grid menu view is selected.

Select, for example, Settings by pressing Select.

You can change the menu view in the Menu view submenu. See Main display

settings on page 91.

3. If the menu contains submenus, select the one that you want, for example Call

settings.

4. If the selected submenu contains further submenus, repeat step 3.

5. Select the setting of your choice.

6. To return to the previous menu level, press Back, and to exit the menu, press

Exit.

By a shortcut

The menus, submenus and setting options are numbered, and you can access some

of them by using their shortcut number.

To access the menu, press Menu. Key in quickly, within 2 seconds, the index

number of the menu function that you want to access.

To return to the previous menu level, press Back, and to exit the menu, press Exit.

■ List of menu functions

1. Messages

1. Create message

2. Inbox

3. Outbox

4. Sent items

5. Saved items

6. Instant messages

7. E-mail

8. Voice messages

9. Info messages

10.Service commands

11.Delete messages

12.Message settings

13.Message counter

2. Contacts

1. Search

2. Add new contact

3. Delete

4. My presence

5. Subscribed names

6. Copy

7. Settings

8. Speed dials

9. Voice tags

10.Info numbers

11.Service numbers ¹

12.My numbers

13.Caller groups²

3. Call register

1. Missed calls

2. Received calls

3. Dialled numbers

4. Delete recent call lists

5. Call duration

6. GPRS data counter

7. GPRS connection timer

8. Message counter

9. Positioning

4. Settings

1. Profiles

2. Themes

3. Tone settings

1. Shown if supported by your SIM card. To check availability, contact your network operator or

service provider.

2. If Info numbers, Service numbers or both are not supported, the number of this menu item

changes accordingly.

4. Main display settings

5. Mini display settings

6. Time and date settings

7. Personal shortcuts

8. Connectivity

9. Call settings

10.Phone settings

11.Enhancement settings

12.Configuration settings

13.Security settings

14.Restore factory settings

5. Gallery

1. Images

2. Video clips

3. Themes

4. Graphics

5. Tones

6. Recordings

6. Media

1. Camera

2. Media player

1. This menu is shown only if the phone is or has been connected to a compatible enhancement

available for the phone.

3. Radio

4. Voice recorder

7. Push to talk

1. Switch PTT on /Switch PTT off

2. Callback inbox

3. Group list

4. Contacts list

5. Add group

6. PTT settings

7. Configuration settings

8. Services

8. Organiser

1. Alarm clock

2. Calendar

3. To-do list

4. Notes

5. Synchronisation

6. Wallet

7. Calculator

8. Stopwatch

9. Countdown timer

9. Applications

1. Games

2. Collection

10.Web

1. Home

2. Bookmarks

3. Download links

4. Last web addr.

5. Service inbox

6. Settings

7. Go to address

8. Clear the cache

11.SIM services

1. Only shown if supported by your SIM card. The name and contents vary depending on the SIM

card.

6. Menu functions

■ Messages

You can read, write, send, and save text, multimedia, and e-mail

messages. All messages are organised into folders.

Note: When sending messages, your device may display the words Message sent.

This is an indication that the message has been sent by your device to the message

centre number programmed into your device. This is not an indication that the

message has been received at the intended destination. For more details about

messaging services, check with your service provider.

Text messages (SMS)

Using the Short Message Service (SMS) you can send and receive multi-part

messages made of several ordinary text messages (network service) that can

contain pictures.

Before you can send any text, picture, or e-mail message, you need to save your

message centre number, see Message settings on page 72.

Your device supports the sending of text messages beyond the normal 160-character limit. If

your message exceeds 160 characters, it will be sent as a series of two or more messages.

At the top of the display you can see the message length indicator counting backwards from

160. For example, 10/2 means that you can still add 10 characters for the text to be sent as

two messages.

Note that using special (Unicode) characters such as ë, â, á, ì take up more space.

Note: Only phones that offer picture message features can receive and display

picture messages.

Writing and sending SMS messages

1. Press Menu, and select Messages, Create message, and Text message.

2. Write the message. See Writing text on page 41.

You can insert text templates or a picture into the message. See Templates on

page 54. Each picture message comprises several text messages. Sending one

picture or multi-part message may cost more than sending one text message.

3. To send the message, press Send or the call key

4. Enter the recipient’s phone number, or press Search to retrieve a phone

number from Contacts, and press OK.

Options for sending a message

After you have written a message, press Options, and select Sending options and

one of the following options:

• To send a message to several recipients, select Send to many. The message is

sent separately to each recipient, which may cost more than sending one

message.

• To send a message as SMS e-mail, select Send as e-mail. Key in the recipient’s

e-mail address, or search for it in Contacts, and press OK.

• To send a message using a predefined message profile, select Sending profile

and a message profile.

To define a message profile, see Message settings on page 72.

Reading and replying to an SMS message

The indicator

SMS. The blinking

is shown when you have received a message or an e-mail using

indicates that the message memory is full. Before you can

receive new messages, delete some of your old messages in the Inbox folder.

1. To view a new message, press Show, or to view it later, press Exit.

To read the message later, press Menu, and select Messages, and Inbox. If more

than one message is received, select the message you want to read. An unread

message is indicated by

in front of it on the list of messages.

2. While reading a message, press Options. You can select to delete, forward, edit

the message as a text message or as an e-mail, move it to another folder, or

extract message details. You can also copy text from the beginning of a

message to your phone calendar as a reminder note. When reading a picture

message, you can save the picture in the Templates folder.

3. To reply to a message, press Reply. To reply as a text message, select Text

message, or to reply as a multimedia message, select Multimedia msg.

When replying to an e-mail, first confirm or edit the e-mail address and

subject, then write your reply message.

4. To send the message to the displayed number, press Send or the call key

and OK.

Templates

To access the template list, press Menu, and select Messages, Saved items, Text

messages and Templates. To add a text ( ) or picture ( ) template in a

message, select it, press Options, and to complete the message, select Edit (or Edit

text for picture template).

To add a template while you are writing or replying to a message, press Options,

and select Use template to insert a text template into the message or the e-mail.

Select Insert picture to insert a picture into the text message.

Multimedia messages

Note: Only devices that offer compatible multimedia message or e-mail features

can receive and display multimedia messages.

To check availability and to subscribe to the multimedia messaging network

service, contact your network operator or service provider. See Settings for

multimedia messages on page 73.

A multimedia message can contain text, sound, a picture, a calendar note, a

business card, or a video clip. If the message is too large, the phone may not be

able to receive it. Some networks allow text messages that include an Internet

address where you can view the multimedia message.

You cannot receive multimedia messages during a call, a game, another Java

application, or an active browsing session over GSM data. Because delivery of

multimedia messages can fail for various reasons, do not rely solely upon them for

essential communications.

Writing and sending a multimedia message

1. To create and send a multimedia message, press Menu, and select Messages,

Create message, and Multimedia msg.

2. Key in the message. See Writing text on page 41.

• To insert a file in the message, press Options, select Insert, and select the

desired option. You cannot select an option if it is dimmed.

If you select Image, Sound clip, or Video clip, the list of available folders in

the Gallery is shown. Open a specific folder, scroll to the desired file, press

Options, and select Insert. The file is attached when the file name appears

in the message.

If you select New sound clip, the voice recorder is opened, and you can start

a new recording. When you end the recording, it is added to the message.

• To insert a business card or a calendar note in the message, press Options,

select Insert and Business card or Calendar note.

• Your phone supports multimedia messages that contain several pages

(slides). Each slide can contain text, one image, a calendar note, a business

card, and one sound clip. To insert a slide in the message, press Options,

and select Insert and Slide.

To open a desired slide if the message contains several slides, press Options,

and select Previous slide, Next slide or Slide list.

To set the interval between the slides, press Options, and select Slide

timing. To move the text component to the top or bottom of the message,

select Place text first or Place text last.

3. To view the message before sending it, press Options, and select Preview.

4. To send the message, press Send or the call key

, and select Phone number.

To send the message to an e-mail address or to many recipients, select E-mail

address or Many.

5. Enter the recipient’s phone number (or e-mail address) or search for it in

Contacts. Press OK and the message is moved to the Outbox folder for sending.

It takes more time to send a multimedia message than to send a text message.

While the multimedia message is being sent, the animated

is displayed,

and you can use other functions on the phone. If an interruption occurs while

the message is being sent, the phone tries to resend the message a few times. If

these attempts fail, the message remains in the Outbox folder. You can try to

resend it later.

The sent message is saved in the Sent items folder if the setting Save sent

messages is set to Yes. See Settings for multimedia messages on page 73.

When the message is sent, it is not an indication that the message has been

received at the intended destination.

forwarding some images, ringing tones, and other content.

Reading and replying to a multimedia message

Important: Multimedia message objects may contain viruses or otherwise be

harmful to your device or PC. Do not open any attachment if you are not sure of

the trustworthiness of the sender.

The default setting of the multimedia message service is generally on.

The appearance of a multimedia message may vary depending on the receiving

device.

When the phone is receiving a multimedia message, the animated

displayed. When the message is received,

and the text Multimedia message

received are shown.

The blinking

indicates that the memory for multimedia messages is full. See

Multimedia messages memory full on page 59.

1. To read a received multimedia message, press Show, or to view it later, press

Exit.

To read the message later, press Menu, and select Messages, and Inbox. On the

list of messages, an unread message is indicated by

. Scroll to the message

that you want to view, and press Select.

2. The function of the middle selection key changes according to the currently

displayed attachment in the message.

• To view the whole message if the received message contains a presentation,

press Play.

Otherwise, press Play to listen to a sound clip or view a video clip attached

to the message. To zoom in on an image, press Zoom. To view a business

card or a calendar note, press View. To open a theme object, press Open. To

open a streaming link, press Load.

3. To reply to the message, press Options, and select Reply, and Text message, or

Multimedia msg. Key in the reply message, and press Send. You can send the

reply message only to the person who sent you the original message.

4. Press Options, and you can also, for example, open and save the attached file

or to view its details, and to delete, or forward the message.

After you have sent the reply message, you can edit it and, for example, send it

to other persons, or send it as an e-mail.

Multimedia messages memory full

When you have a new multimedia message waiting and the memory for the

messages is full,

blinks and Multimedia memory full, view waiting msg. is

shown. To view the waiting message, press Show. To save the message, press Save

and delete old messages by first selecting the folder and then the oId message to

be deleted.

To discard the waiting message, press Exit and Yes. If you press No, you can view

the message.

Inbox, Outbox, Saved items and Sent items folders

• The phone saves in the Inbox folder the text and multimedia messages that

have been received.

• Multimedia messages that have not yet been sent are moved to the Outbox

folder.

• The sent messages are saved in the Sent items folder if the settings Save sent

messages for text messages and Save sent messages for multimedia messages

in Message settings are set to Yes.

• To save the text message that you are writing and wish to send later in the

Saved items folder, press Options, and select Save message, and Saved text

msgs.. For multimedia messages, select the option Save message. Unsent

messages are indicated with

• To organise your text messages, you can move some of them to My folders, or

add new folders for your messages. Select Messages, Saved items, Text

messages and My folders.

To add a folder, press Options, and select Add folder. If you have not saved any

folders, press Add.

To delete or rename a folder, scroll to the desired folder, press Options, and

select Delete folder or Rename folder.

Instant messages

Instant messaging (network service) is a way to send short, simple text messages

to online users, delivered over TCP/IP protocols. Your contact list shows you when

your contacts on the list are online and available to participate in an instant

messaging conversation. When you have written and sent your message, it

remains displayed. The reply message appears below your original message.

Before you can use instant messaging, you need to subscribe to the service. To

check the availability and charging and to subscribe to the service, contact your

network operator or service provider, from whom you also receive your unique ID

and password and the settings for the instant messaging.

To set the required settings for the instant messaging service, see Connect.

settings in the section Entering the instant messaging menu on page 61.

While you have connected to the instant messaging service, you can use the other

functions of the phone, and the instant messaging session remains active in the

background. Depending on the network, the active instant messaging session may

consume the phone battery faster, and you may need to connect the phone to a

charger.

Entering the instant messaging menu

To enter the Instant messages menu while still offline, press Menu, and select

Messages and Instant messages.

• To connect to the instant messaging service, select Login. You can set the

phone to automatically connect to the instant messaging service when you

enter the Instant messages menu. See Connecting to and disconnecting from

the instant messaging service on page 62.

• To view, erase, or rename the conversations that you have saved during an

instant messaging session, select Saved convers.. You can select Saved convers.

also when you have connected to the instant messaging service.

• To view the settings needed for instant messaging and presence settings,

select Connect. settings.

You may receive the settings as a configuration message, see Configuration

settings service on page 18. To key in the settings manually, see Configuration

settings on page 99.

Select Configuration and Default or Personal config. according to which

configuration settings supports instant messaging.

Select Account and select an instant messaging account provided by the

service provider.

Select User ID to key in your user ID received from the service provider.

Select Password to key in the password received from the service provider.

Connecting to and disconnecting from the instant messaging service

To connect to the instant messaging service, enter the Instant messages menu,

select the desired instant messaging service if needed, and select Login. When the

phone has successfully connected, Logged in is displayed. To disconnect from the

instant messaging service, select Logout.

Tip: To set the phone to automatically connect to the instant messaging

service when you enter the Instant messages menu, connect to the instant

messaging service, select My settings, Automatic login and On IM start-up.

Starting an instant messaging conversation

Enter the Instant messages menu, connect to the instant messaging service, and

you can start a conversation in different ways.

• Select Conversations. The list of new and read messaging sessions or

invitations to instant messaging during the currently active session is

displayed. Scroll to a message or an invitation, and press Open.

indicates the new and

indicates the invitations.

the read instant messages.

the read group messages.

The icons and texts on the display may vary depending on the instant

messaging service.

• Select IM contacts. The contacts that you have added from the phone’s

contacts memory are displayed. Scroll to the contact with whom you would

like to start instant messaging, and press Chat.

indicates that you have received a new message from a contact.

indicates an online contact and

memory of the phone.

an offline contact in the contact

indicates a blocked contact. Refer to Blocking and unblocking messages on

page 66.

You can add contacts to the list. See Contacts for instant messaging on page

66.

• Select Groups and Public groups (dimmed if the group functionality is not

supported by the network). The list of bookmarks to public groups provided by

the network operator or service provider is displayed. To start a conversation,

scroll to a group, and press Join. Enter the screen name that you want to use as

a nickname in the conversation. When you have successfully joined in the

group conversation, you can start a group session. You can also create a

private group. See Groups on page 67.

• Select Search and Users or Groups to search for other instant messaging users

or public groups on the network by phone number, screen name, e-mail

address, or name. If you select Groups, you can search for a group by a member

in the group or by group name, topic or ID.

To start the session when you have found the user or the group that you want,

press Options, and select Chat or Join group.

• You can start a session from Contacts. See Viewing the subscribed names on

page 83.

Accepting or rejecting an instant messaging invitation

In standby mode, when you are connected to the instant messaging service and

you receive a new invitation, New invitation received is displayed. Press Read to

read it. If more than one invitation is received, scroll to an invitation, and press

Open.

• To join the private group conversation, press Accept. Enter the screen name

that you want to use as a nickname in the conversation.

• To reject or delete the invitation, press Options and select Reject or Delete. You

can key in an explanation for the rejection.

Reading a received instant message

In standby mode, when you are connected to the instant messaging service and

you receive a new message that is not a message associated with an active

conversation, New instant message is displayed. Press Read to read it.

If more than one message is received, the number of messages, followed by new

instant messages, is displayed. Press Read, scroll to a message and press Open.

New messages received during an active session are held in the Conversations of

the Instant messages menu. If you receive a message from someone who is not in

IM contacts, the sender ID is displayed. If the sender is in the phone memory and

the phone recognises it, the name of the person is displayed. To save a new

contact that is not in the phone memory, press Options and select Save contact,

or to add a new detail to the selected contact, select Add to contact.

Participating in an instant messaging conversation

Join or start a conversation by pressing Write or start writing.

Tip: If you receive a new message during a session from a person who is

not taking part in the current session, the icon

is displayed, and the

phone sounds an alert tone.

Key in your message, and press Send or the call key

to send it. The message

stays on the display, and the reply message appears below your message.

Editing your own settings

1. Enter the Instant messages menu, and connect to the instant messaging

service.

2. To view and edit your own availability information or screen name, select My

settings.

• To allow all the other instant messaging users to see you as being online,

select Availability and Available for all.

• To allow only the contacts on your instant messaging contact list to see you

as being online, select Availability and Avail. for contacts.

• To appear as being offline, select Availability and Appear offline.

When you are connected to the instant messaging service,

are online and that you appear as offline to others.

indicates that you

Contacts for instant messaging

You can add contacts to the instant messaging contacts list.

1. Connect to the instant messaging service, select IM contacts.

2. Press Options and select Add contact. You can select to key in the user ID, to

add a contact from the phone contact memory, or to search other contacts or

to copy a contact from your contact list on the service provider’s server.

3. To start an instant messaging service, press Chat, or if there is a new message

from the contact, press Open.

4. Press Options and select, for example, to view the details of a selected contact,

to copy contacts from your instant messaging contact list to the service

provider’s server, or to select the contacts in the instant messaging list from

whom you want to receive availability alerts.

Blocking and unblocking messages

To block messages, connect to the instant messaging service, and select

Conversations, IM contacts, or join or start a session. Select the contact from

whom you want to block incoming messages, and press Options. Select Block

contact, and press OK to confirm.

To unblock messages, connect to the instant messaging service, and select

Blocked list. Scroll to the contact from whom you want to unblock the messages,

and press Unblock.

You can also unblock messages from the contact list.

Groups

If groups are supported by the network, you can create your own private groups

that exist only during a instant messaging session, or use the public groups where

provided by the service provider.

Connect to the instant messaging service, and select Groups.

• Select Public groups, press Join and, if you are not in the group, enter your

screen name. Press Options, and select Delete group to delete a group from

your group list.

Select Search groups to search a group by group member or by group name,

topic, or ID.

• Select Create group. Enter the name for the group and the screen name to be

used as your nickname in this group.

Mark the names in the contacts list to add them to the private group list, or

unmark them to remove them from the list. You need to send an invitation to

the new members in the group.

The online contacts are indicated by

, the offline contacts by

, and the

blocked contacts by . You cannot add contacts that are dimmed in the list.

The icons may vary depending on the instant messaging service.

E-mail messages

The e-mail application that uses (E)GPRS (network service), allows you to access

your e-mail account from your phone, when you are not in the office or at home.

To use the e-mail function on your phone, you need a compatible e-mail system.

You can write, send, and read e-mails with your phone. You can also save and

delete the e-mails on a compatible PC. Your phone supports POP3 and IMAP4 e-

mail servers.

Before you can send and retrieve any e-mail messages, you may need to do the

following:

• Obtain a new e-mail account or use your current account. To check the

availability of your e-mail account, contact your e-mail service provider.

• Check your e-mail settings with your network operator or e-mail service

provider. You can receive e-mail settings as a configuration message, see

Configuration settings service on page 18.

• To check your settings, press Menu, and select Messages, Message settings and

E-mail messages. See Settings for e-mail application on page 75.

This application does not support keypad tones.

Writing and sending an e-mail

You can write your e-mail message before connecting to the e-mail service, or

connect to the service first, and then write and send your e-mail.

1. Press Menu, and select Messages, E-mail and Create e-mail.

2. Key in the recipient’s e-mail address, or press Edit and key in the e-mail

address, or to search for the e-mail address in Contacts, press Edit and

Options, and select Search. Press OK.

3. You can key in a subject for the e-mail, and press OK.

If you press Options, you can select the message editor, add a new recipient,

add a copy recipient, or a hidden copy recipient.

4. Key in the e-mail message, see Writing text on page 41. The number of

characters that you can key in is shown on the top right of the display.

5. To send the e-mail message, press Send. Select Send now to send the e-mail

immediately. If you select Send later, the e-mail is saved in the Outbox folder.

If you want to edit or continue writing your e-mail later, you can save it in

Drafts by selecting Save draft msg..

When sending the e-mail later, press Menu, and select Messages, E-mail. Press

Options, and select Send now or Retrieve and send.

Downloading e-mail messages

You can download e-mail messages from your e-mail account.

1. Press Menu, and select Messages, E-mail and Retrieve.

Alternatively, press Menu, and select Messages, E-mail, press Options, and

select Retrieve and send to download new e-mail messages and to send e-

mails that have been saved in the Outbox folder.

If the message memory is full, delete some of your older messages before you

start to download new messages.

Your phone makes a connection to the e-mail service. A status bar is shown

while your phone is downloading e-mail messages to your phone.

2. Press Select to view the new message in Inbox, or press Back to view it later.

If you receive more than one message, select the message that you want to

read. An unread message is indicated by

Reading and replying to an e-mail message

Important: E-mail messages may contain viruses or otherwise be harmful to your

device or PC. Do not open any attachment if you are not sure of the

trustworthiness of the sender.

1. Press Menu, select Messages, E-mail and Inbox.

2. While reading the message, press Options to view the details of the selected

message, mark the message as unread, delete, reply, reply to all, forward or

move the message to another folder.

3. To reply to an e-mail, press Reply. You can, for example, include the original

message in the reply.

Confirm or edit the e-mail address and subject, then write your reply.

4. To send the message, press Send and select Send now.

Inbox and Other folders

Your phone has the following folders in the E-mail menu:

•

Inbox for saving e-mails that you have downloaded from your e-mail account.

Other folders contains the folders: Drafts for saving unfinished e-mails,

Archive for organising and saving your e-mails, Outbox for saving e-mails that

have not been sent, if you have selected Send later, see Writing and sending an

e-mail on page 68, and Sent items for saving e-mails that have been sent.

Deleting e-mail messages

To delete e-mail messages, press Menu, and select Messages, E-mail. Press

Options, and select Delete messages.

• To delete all messages from a folder, select the folder, and press Yes.

• To delete all messages from all folders, select All messages, and press Yes.

Deleting an e-mail from your phone does not delete it from the e-mail server.

Voice messages

The voice mailbox is a network service. For more information and for your voice

mailbox number, contact your service provider.

Press Menu, and select Messages, Voice messages and Listen to voice messages to

call your voice mailbox at the phone number that you have saved in the Voice

mailbox number menu.

Info messages

With the Info messages network service you can receive messages on various

topics from your service provider. To check availability, topics and the relevant

topic numbers, contact your service provider.

Service commands

In this menu you can send service requests to your service provider (network

service).

Deleting messages

To delete all messages from a folder, press Menu, and select Messages, Delete

messages, and the folder from which you want to delete the messages. Press Yes,

and if the folder contains unread messages, the phone will ask whether you want

to delete them also. Press Yes again.

Message settings

The message settings affect the sending, receiving, and viewing of messages.

Settings for text messages

1. Press Menu, and select Messages, Message settings, Text messages and

Sending profile.

2. If more than one message profile set is supported by your SIM card, select the

profile you want to change, and select from the following settings:

•

Message centre number to save the phone number of the message centre

that is required for sending text messages. You will receive this number

from your service provider.

•

Messages sent via to select the message type Text, E-mail, Paging or Fax.

Message validity to select the length of time for which the network should

attempt to deliver your message.

•

Default recipient number to save a default number for sending messages for

this profile if you have selected the message type Text. Select E-mail server

to save the e-mail server number if you have selected the message type E-

mail.

•

Delivery reports to ask the network to send delivery reports about your

messages (network service).

Use GPRS, and select Yes to set GPRS as the preferred SMS bearer. Also, set

the GPRS connection to Always online. See GPRS connection on page 95.

Reply via same centre to allow the recipient of your message to send you a

reply using your message centre (network service).

Rename sending profile to change the name of the selected message

profile. The message profile sets are only displayed if your SIM card

supports more than one set. The default profile cannot be renamed.

3. Select Save sent messages and Yes to set the phone to save the sent text

messages in the Sent items folder.

Settings for multimedia messages

You may receive the multimedia configuration settings as an over the air message

from the network operator or service provider. To receive the settings over the air,

see Configuration settings service on page 18.

Press Menu, and select Messages, Message settings and Multimedia msgs.. Select

from the following settings:

•

Save sent messages, and select Yes to set the phone to save sent multimedia

messages in the Sent items folder.

Delivery reports to ask the network to send delivery reports about your

messages (network service).

Scale image down to define the image size when you insert the image to a

multimedia message.

•

Default slide timing to select the default value for timed slides.

Allow multimedia reception, and select No or Yes to receive or block

multimedia messages. To receive multimedia messages only in your home

network, select In home network (default setting).

•

Incoming multimedia messages, and select Retrieve to set the phone to

automatically retrieve newly received multimedia messages, or select Reject if

you do not wish to receive multimedia messages. This setting is not shown if

the Allow multimedia reception is set to No.

Configuration settings, and select Configuration. Only the configurations that

support multimedia messaging are shown. Select a service provider, or Default,

or Personal config. for multimedia messaging. You may receive the multimedia

messaging settings as a configuration message, see Configuration settings

service on page 18. To key in the configuration settings manually, see

Configuration settings on page 99.

Select Account and select a multimedia messaging service account contained

in the active configuration settings.

•

Allow adverts. You can receive or reject advertisements. This setting is not

shown if Allow multimedia reception is set to No or if Incoming multimedia

messages is set to Reject.

Settings for e-mail application

You may receive the e-mail settings as a configuration message, see

Configuration settings service on page 18. To key in the settings manually, see

Configuration settings on page 99.

1. Press Menu, and select Messages, Message settings, and E-mail messages.

2. Select from the following:

•

Configuration and select the set that you would like to activate.

Account to see the accounts provided by the service provider. If more than

one account is displayed choose the one that you want to use.

•

My name. Key in your name or nickname.

E-mail address. Key in e-mail address.

Include signature. You can define a signature that is automatically added to

the end of your e-mail, when you write your message.

•

Reply-to address. Key in the e-mail address to which you want the replies

to be sent.

•

SMTP user name. Key in the name that you want to use for outgoing mails.

SMTP password. Key in the password that you want to use for outgoing

mails.

•

Display terminal window. Select Yes to perform manual user authentication

for Intranet connections.

Incoming server type. Select either POP3 or IMAP4 depending on the type of

e-mail system that you are using. If both types are supported, select IMAP4.

•

Incoming mail settings

If you have selected POP3 as the incoming server type, the following

options are shown: Retrieve e-mails, POP3 user name, POP3 password and

Display terminal window.

If you have selected IMAP4 as the incoming server type, the following

options are shown: Retrieve e-mails, Retrieval method, IMAP4 user name,

IMAP4 password and Display terminal window.

Other settings

To select the other settings for messages, press Menu, and select Messages,

Message settings, Other settings. To change the font size for reading and writing

messages, select Font size.

Message counter

To view how many text, and multimedia messages you have sent and received,

press Menu, and select Messages, Message counter, and Sent messages or

Received messages. To clear the counters, select Clear counters.

■ Contacts

You can save names and phone numbers (Contacts) in the phone

memory or in the SIM card memory.

The phone supports presence enhanced contact (network service) containing My

presence and Subscribed names. In the My presence menu you can publish your

current availability status to communicate to anyone who has access to this

service and who is requesting this information. In the Subscribed names menu you

can create a list of contacts whose presence status you would like to see and use

this list to quickly view their availability status.

Searching for a contact

Press Menu, and select Contacts and Search, or press the scroll key down in

standby mode.

Scroll up or down to the name that you want. If the contact is saved in the SIM

card’ memory,

is shown on the top of the display. Press Details, and scroll to

view the details of the selected contact.

The subscribed names are shown differently, depending on the Contacts view

selection. See Settings for contacts on page 84.

Saving names and phone numbers (Add contact)

Press Menu, and select Contacts and Add new contact. Key in the name, press OK,

and key in the phone number, and press OK.

Tip: Quick save In standby mode, key in the phone number, and press Save.

Key in the name, and press OK.

Saving multiple numbers or text items per name

You can save different types of phone numbers and short text items for a contact

in the phone memory for contacts. A text item may be, for example, an address.

The first number you save is automatically set as the default number, and it is

indicated with a frame around the number type indicator, for example . When

you select a name from contacts, for example, to make a call, the default number

is used unless you select another number.

1. Ensure that the memory in use is either Phone or Phone and SIM. See Settings

for contacts on page 84.

2. To access the list of names and phone numbers, press the scroll key down in

standby mode.

3. Scroll to the name to which you want to add a new number or text item.

4. Press Details and Options, and select Add number or Add detail.

5. To add a number or detail, select a number type or text type.

If you are connected to the presence service and select the text type User ID,

select Search to search for an ID by a mobile phone number or an e-mail

address on the server of the operator or service provider. See Presence-

enhanced contacts - My presence on page 80. If only one ID is found, it is

automatically saved. Otherwise, to save the ID, press Options, and select Save.

Select Enter ID manually, key in the ID, and press OK.

To change the number or text type, press Options, and select Change type . You

cannot change the type of an ID when it is in the IM contacts or Subscribed

names list.

To set the selected number as the default number, press Options, and select

Set as default.

6. Key in the number or text item, and press OK to save it.

7. Press Back and then Exit to return to standby mode.

Adding an image to a contact

You can add an image in a supported format to a certain number of contacts

saved in the phone memory.

Press the scroll key down in standby mode, scroll to a contact to which you want

to add an image, and press Details. Press Options, and select Add image. Open the

desired folder in the Gallery, scroll to the image that you want to add, press

Options and select Save to contacts. A copy of the image is added to the contact.

Editing or deleting details in the contacts

Search for the contact, and press Details. Scroll to the name, number, text item, or

image that you want to edit or delete.

•

To edit, press either Edit or Change, or press Options, and select Edit name,

Edit number, Edit detail, or Change image, depending on the Contacts view

selection. You cannot edit or delete an ID when it is on the IM contacts or in

the Subscribed names list.

• To delete a number, a text item, or an image attached to the contact, press

Options, and select Delete number, Delete detail, or Delete image. Deleting an

image from contacts does not delete it from Gallery.

Deleting contacts

Press Menu, and select Contacts, and Delete to delete contacts and all the details

attached to them. To delete contacts one by one or all at once, select One by one

or Delete all.

Presence-enhanced contacts - My presence

With the presence service (network service), you can share your presence status

with other users, for example, your family, friends, and colleagues. Presence status

includes your availability, status message, and personal logo. Other users who

have access to the service and are requesting your information, are able to see

your status. The requested information is shown in Subscribed names in the

viewers’ Contacts menu. You can personalize the information that you want to

share with others and control who can see your status.

Before you can use presence, you need to subscribe to the service. To check the

availability and costs, and to subscribe to the service, contact your network

operator or service provider, from whom you also receive your unique ID,

password, and the settings for the service. See Configuration settings on page 99.

To use presence, connect to the service. While you are connected to the presence

service, you can use the other functions of the phone, and the presence service is

active in the background. If you disconnect from the service, your presence status

is shown for a certain amount of time for the viewers depending on the service

provider.

Press Menu, and select Contacts, and My presence. Select from the following

options:

•

Connect to ’My presence’ service or Disconnect to connect to or to disconnect

from the service.

My current presence, and select, for example, to view your current private or

public status, to change your presence status, or to select the groups with

whom you want to share your presence status information.

•

Viewers, and select to view all the persons who have subscribed to, who are

allowed to view, or who are blocked from viewing your presence information.

Settings, and select from following:

Show current presence in idle to show the current status indicator in standby

mode.

Synchronise with profiles to select whether you want to update My presence

message and My availability manually or automatically by linking them to the

currently active profile. See Profiles on page 89. You cannot link a personalised

status logo to a profile.

Connection type to select how the phone connects to the presence service

when it is switched on.

IM and my presence settings and select from following:

•

Configuration. Only the configurations that support presence service are

shown. Select a service provider, Default, or Personal config. for presence

service. You may receive the presence service settings as a configuration

message, see Configuration settings service on page 18. To key in the

configuration settings manually, see Configuration settings on page 99.

•

Account and select a presence service account contained in the active

configuration settings.

•

User ID to key in your user ID received from the service provider.

Password to key in the password received from the service provider.

Presence-enhanced contacts - Subscribed names

You can create a list of contacts whose presence status information you want to

be available. You can view the information only if it is allowed by your contact or

the network.

Ensure that the memory in use is either Phone or Phone and SIM. See Settings for

contacts on page 84.

To connect to the presence service, press Menu, and select Contacts, My presence,

and Connect to My presence service. You can view the subscribed contacts even

when you are not connected to the presence service, but you cannot see the

presence status information about the contact.

Adding contacts to the subscribed names

1. Press Menu, and select Contacts, and Subscribed names.

2. If your list of contacts is empty, press Add. Otherwise, press Options, and

select Subscribe new.

3. Select a contact from the list. If the contact has a saved ID, the contact is

added to the subscribed names list.

Tip: To subscribe to a contact from the Contacts list, search for the

contact, press Details, and Options. Select Request presence and As

subscription.

To view only the presence information, select Request presence and One

time only.

Viewing the subscribed names

See Searching for a contact on page 77.

1. To view the presence information, press Menu, and select Contacts, and

Subscribed names.

The status information of the first contact on the subscribed names list is

displayed. The information that the person wants to make available to others

may include text and an icon. The

and

icons indicate that the

person is either available, busy, or not available.

indicates that the person’s presence information is not available.

2. Press Options, and select from the list of options.

Unsubscribing a contact

To unsubscribe a contact, search for the contact from the Contacts list, and press

Details. Select the user ID, press Options, select Unsubscribe, and press OK.

Copying contacts

Press Menu, and select Contacts and Copy to copy names and phone numbers

from the phone memory to your SIM card memory and vice versa. The text items,

such as e-mail addresses, saved in the phone memory are not copied to the SIM

card.

Settings for contacts

Press Menu, and select Contacts and Settings, and select from the following:

•

Memory in use to select the memory that you want to use for your contacts. If

you select Phone and SIM, you can view the contacts in both memories but the

names and numbers will be saved in the phone memory.

•

Contacts view to select how the contacts are displayed.

Memory status to view the status of both memories for contacts.

Sending and receiving a business card

You can send and receive a person’s contact information from a compatible device

that supports the vCard standard as a business card.

When you have received a business card, press Show and Save to save the

business card in the phone memory.

To send a business card, search for the name and phone number that you want to

send from contacts. Press Details and Options, and select Send bus. card. Select

Via infrared, Via text message (network service), or Via multimedia (network

service).

Voice dialing

You can call a contact by saying a voice tag that you have recorded for that

contact. Any spoken words, such as a name, can be a voice tag. You can add a

certain amount of voice tags.

Before using voice tags, note that:

•

Voice tags are not language-dependent. They are dependent on the speaker's voice.

You must say the name exactly as you said it when you recorded it.

Voice tags are sensitive to background noise. Record voice tags and use them in a quiet

environment.

•

Very short names are not accepted. Use long names and avoid similar names for different

numbers.

Note: Using voice tags may be difficult in a noisy environment or during an

emergency, so you should not rely solely upon voice dialing in all circumstances.

Adding and managing voice tags

Save or copy in the phone memory the contacts to which you want to add a voice

tag.

1. In standby mode, press the scroll key down, and scroll to the contact to which

you want to add a voice tag.

2. Press Details, scroll to the desired phone number, press Options, and select

Add voice tag

3. Press Start, and speak clearly the word(s) that you want to record as a voice

tag. After recording, the phone plays the recorded tag.

appears after the phone number with a voice tag in Contacts.

Making a call by using a voice tag

If the phone has an application running that is sending or receiving data using the

(E)GPRS connection, you must end the application before using voice tags.

1. In standby mode, press and hold the volume-down key or the right selection

key

. A short tone sounds, and Speak now is displayed.

2. Speak the voice tag clearly. The phone plays the recognised voice tag, and dials

the phone number of the voice tag after 1.5 seconds.

If you are using a compatible headset with the headset key, press and hold the

headset key to start the voice dialing.

Other functions in the Contacts

Press Menu, and select Contacts, and select from the following:

•

Speed dials to assign a number to a speed-dialing key. Scroll to the speed-

dialing key number that you want, press Assign, or if a number has already

been assigned to the key, press Options, and select Change. Press Search, and

select first the name, then the number that you want to assign.

See also Speed dialling in Call settings on page 96, and Speed dialing on page

37.

•

Voice tags to listen to, delete, or change the saved voice tags.

Info numbers or Service numbers (network services) are numbers that your

service provider may have included in your SIM card.

•

My numbers to view the numbers assigned to your SIM card if this is allowed

by the card.

•

Caller groups to arrange the names and phone numbers saved in Contacts into

caller groups. For each caller group, you can set, for example, the phone to

sound a specific ringing tone, and show a selected graphic on the display when

you receive a call from a phone number in the group. To set the phone to ring

only upon calls from phone numbers belonging to a selected caller group, see

Alert for in Tone settings on page 90.

■ Call register

The phone registers the phone numbers of missed, received and dialled

voice calls and push to talk addresses of one-to-one push to talk calls,

and the approximate length of your calls.

The phone registers missed and received calls only if the network supports these

functions, and the phone is switched on and within the network service area.

When you press Options in the Missed calls, Received calls and Dialled numbers

menu, you can, for example, view the date and the time of the call, edit or delete

the phone number from the list, save the number in Contacts, or send a message

to the number.

Recent calls lists

Press Menu, and select Call register and then select from the following:

•

Missed calls to view the list of the latest phone numbers from which somebody

has unsuccessfully tried to call you (network service).

•

Received calls to view the list of the latest phone numbers from which you

have most recently accepted calls (network service).

Dialled numbers to view the list of the phone numbers that you have most

recently called or attempted to call.

Delete recent call lists to delete the recent calls lists.

Call counters and call timers

Note: The actual invoice for calls and services from your service provider may

vary, depending upon network features, rounding-off for billing, taxes and so

forth.

Press Menu, and select Call register and select from the following:

•

Call duration. Scroll to view the approximate duration of your incoming and

outgoing calls in hours, minutes, and seconds.

•

GPRS data counter. Scroll to check the approximate amounts of data that were

sent or received in the last session, data sent and received in total, and to clear

the counters.

•

GPRS connection timer. Scroll to check the approximate duration of the last

GPRS connection or the total GPRS connection time.

Message counter

To view how many text, instant messaging and multimedia messages you have

sent and received, press Menu, and select Call register, Message counter and Sent

messages or Received messages. To clear the counters, select Clear counters.

Positioning

The network may send you a location request. You can ensure that the network

will deliver location information of your phone only if you approve it (network

service). Contact your network operator or service provider to subscribe and to

agree upon the delivery of location information.

• To accept or reject the location request, press Accept or Reject. If you miss the

request, the phone automatically accepts or rejects it according to what you

have agreed with your network operator or service provider. The phone displays

1 missed position request. To view the missed location request, press Show.

To view the information on the 10 most recent privacy notifications and requests

or to delete them, press Menu, and select Call register, Positioning, Position log,

and Open folder or Delete all.

■ Settings

Profiles

You can customize tones with preset profiles for different events, environments,

or caller groups.

Press Menu, and select Settings, and Profiles. Scroll to a profile and press Select.

• To activate the selected profile, select Activate.

• To set the profile to be active for a certain amount of time up to 24 hours,

select Timed, and set the end time. When the time set for the profile expires,

the previous profile that was not timed becomes active.

• To personalise the profile, select Personalise. You can change the same settings

also in the Tone settings menu. See Tone settings on page 90.

To change your presence status information, select My presence. This menu is

available if you have set Synchronise with profiles to On. See Presence-

enhanced contacts - My presence on page 80.

To rename a profile, select Profile name. The General profile cannot be

renamed.

Themes

A theme contains many elements for personalising your phone, such as wallpaper,

screen saver, color scheme and a ringing tone.

Press Menu, and select Settings, and Themes. Select from following:

•

Select theme to open the list of folders in the Gallery. To set a theme in your

phone, open the Themes folder, and select a theme.

•

Theme downloads to open a list of downloads links to download more themes.

Refer to Downloading on page 138.

Tone settings

Press Menu, and select Settings and Tone settings. You can find the same settings

in the Profiles menu. The settings you make also change the settings in the active

profile.

You can select, for example, how the phone notifies you of an incoming voice call,

select the ringing tone for incoming calls and messages, set the push to talk

notification tones and voice status, set the ringing volume, and select the phone

to ring only for call from phone numbers that belong to a selected caller group.

Main display settings

Press Menu, and select Settings and Main display settings. You can change the

following settings:

•

Wallpaper to add the background image to the main display in standby mode.

To select, activate, or deactivate the wallpaper, select Select wallpaper, On or

Off. Select Select slide set and a folder in the Gallery to use the images in the

folder as a slide set.

To download more images for wallpaper, select Graphic downloads.

•

Colour schemes to change the color in some display components, for example,

menu background color and signal and battery bar colors.

Operator logo to set your phone to display or hide the operator logo. If you

have not saved the operator logo, the Operator logo menu is dimmed.

For more information on availability of an operator logo, contact your network

operator or service provider.

•

Menu view to set the way the phone displays the main menu. Select List or

Grid.

Mini display settings

Press Menu, and select Settings and Mini display settings. You can change the

following settings:

•

Wallpaper to add the background image to your phone mini display in standby

mode. The wallpaper is not displayed when the phone activates the screen

saver.

To download more images for wallpaper, select Graphic downloads.

•

Colour schemes to change the color in some display components, for example,

menu background color and signal and battery bars.

Screen saver to activate the screen saver for the mini display, select On. To set

the time after which the screen saver on the mini display is activated, select

Time-out. To select a graphic for the screen saver, select Select s. saver, and

open Graphics, Scr. savers. To download more images for screen saver, select

Graphic downloads.

Time and date settings

Press Menu, and select Settings and Time and date settings. Select Clock and Date

to make time and date settings and to select if the time and date are shown on the

display in standby mode. Select Auto-update of date & time (network service) to

set the phone to automatically update the time and date according to the current

time zone. Auto-updating may cause some alarms you have set to expire.

If the battery is removed from the phone for a long time or if the battery is

discharged, you may need to set the time again.

Personal shortcuts

To select a function for the right selection key and add voice commands for some

functions, press Menu, and select Settings, and Personal shortcuts.

• Select Right selection key to set a function for the right selection key. Scroll to

a function and select it.

• Select Voice commands and a command folder. Select the function to which

you want to add a voice command, and press Add. You can add voice

commands for a certain numbers of functions.

To add a voice command, refer to Adding and managing voice tags on page 85.

To activate a voice command, refer to Making a call by using a voice tag on

page 86.

During a call, or when an application using the (E)GPRS connection is sending

or receiving data, you cannot activate or add a voice command.

Connectivity

Infrared

Do not point the IR (infrared) beam at anyone's eye or allow it to interfere with other IR

devices. This device is a Class 1 laser product.

You can set up the phone to send and receive data through its infrared (IR) port.

You can send or receive data (such as business cards) to or from a compatible

phone or data device (such as a computer) using the IR port of your phone.

To use an IR connection, the compatible device with which you want to establish a

connection must be IrDA compliant.

When sending or receiving data using IR, ensure that the IR ports of the sending

and receiving devices are pointing at each other and that there are no

obstructions between the devices. The preferable distance between the two

devices in an infrared connection is 1 meter (3.28 feet) at most.

To activate the IR port of your phone to receive data using IR, press Menu, and

select Settings, Connectivity, and Infrared.

To deactivate the IR connection, press Menu, and select Settings, Connectivity,

and Infrared. Press Yes when the phone displays Deactivate infrared?.

If data transfer is not started within 2 minutes after the activation of the IR port,

the connection is canceled and must be restarted.

GPRS

General Packet Radio Service (GPRS) is a network service that allows mobile

phones to be used for sending and receiving data over an Internet Protocol (IP) -

based network. GPRS is a data bearer that enables wireless access to data

networks such as the Internet.

Enhanced GPRS (EGPRS) uses enhanched data rates for global evolution (EDGE), a

radio interface modulation technique, to increase the data rates of GPRS.

The functions of your phone that may use (E)GPRS are messaging, browsing pages,

e-mail application, remote synchronisation, push to talk, application

downloading, and the PC dial-up (for example, Internet and e-mail).

Before you can use (E)GPRS technology:

• Contact your network operator or service provider to check availability, to

subscribe to the (E)GPRS service, and to obtain information on data transfer

speed and pricing.

• Save the (E)GPRS settings for each application that uses (E)GPRS.

When you have selected GPRS as a data bearer, the phone uses EGPRS instead of

GPRS if this is available in the network. You cannot select between EGPRS and

GPRS, but for some applications you may be able to select either GPRS or GSM

data (CSD, Circuit Switched Data).

GPRS connection

To define the settings for (E)GPRS connections, press Menu, and select Settings,

Connectivity, GPRS, and GPRS connection.

• Select Always online to set the phone to automatically register to an (E)GPRS

network when you switch the phone on.

When you start an application using (E)GPRS, the connection between the

phone and network is established. When you exit the application, the (E)GPRS

connection ends, but the phone is still registred to the (E)GPRS network.

If you receive a call or a text message or make a call during an (E)GPRS

connection, the (E)GPRS connection is suspended (on hold).

The indicator for GPRS and (E)GPRS is the same.

• Select When needed to set the phone to register to an (E)GPRS network and

establish an (E)GPRS connection when an application using (E)GPRS requires

it. The (E)GPRS connection will close when you exit the application.

The phone supports three simultaneous (E)GPRS connections. For example, you

can browse XHTML pages, receive multimedia messages, and have an ongoing PC

dial-up connection at the same time.

GPRS modem settings

You can connect the phone with an infrared or a data cable connection to a

compatible PC, and use the phone as a modem to enable (E)GPRS connection from

the PC.

To define the settings for (E)GPRS connections from the PC, press Menu, and

select Settings, Connectivity, GPRS and GPRS modem settings.

• Select Active access point to activate the access point that you want.

• Select Edit active access point to change the access point settings. Contact

your network operator or service provider for the access point name.

You can also set the (E)GPRS dial-up service settings (access point name) on the

PC using the Nokia Modem Options software. If you have set the settings both on

the PC and on the phone, the PC settings will be used.

Call settings

Press Menu, and select Settings and Call settings. Select from the following

settings:

•

Call divert (network service) to direct your incoming calls to another number,

for example, to your voice mailbox (network service). For details, contact your

service provider.

•

Anykey answer, select On, and you can answer an incoming call by briefly

pressing any key except the power key, the push to talk key, the selection keys

and

, and

•

Answer when fold is opened to select whether opening the fold automatically

answers an incoming call.

Automatic redial to set the phone to make a maximum of 10 more attempts to

connect the call after an unsuccessful call attempt.

Speed dialling to set the phone to dial the phone numbers assigned to the

speed-dialing keys, from

, by pressing and holding the

corresponding number key.

•

Call waiting to request the network to notify you of an incoming call while you

have a call in progress (network service).

Summary after call to set the phone to briefly display the approximate

duration and cost (network service) of the call after each call.

Send my caller ID to set the phone to show your phone number to the person

you are calling (network service). Select Set by network, and the setting agreed

upon with your service provider is used.

•

Line for outgoing calls (network service) to select phone lines 1 or 2, for making

calls. For more information on availability, contact your network operator or

service provider.

If you select Line 2 and have not subscribed to this network service, you are not

able to make calls. However, calls on both lines can be answered regardless of

the selected line.

Phone settings

Press Menu, and select Settings and Phone settings. Select from the following

settings:

•

Language settings, and to set the language for the display texts, select Phone

language. If Automatic is selected, the phone selects the language according

to the information on the SIM card.

To use another language for writing text, select Writing language. You can also

temporarily change the language for writing text. See Writing text on page 41.

•

Memory status to view the amount of free and used memory for each function

in the list.

Security keyguard to set the phone to ask for the security code when you

unlock the keyguard.

When the keyguard is on, calls still may be possible to the official emergency number

programmed into your device. Key in the emergency number and press the call key

•

Cell info display to set the phone to indicate when you use it in a cellular

network based on Micro Cellular Network (MCN) technology (network service).

Welcome note to key in and save a personal note that is shown briefly when

you switch on the phone.

Operator selection to set the phone automatically select one of the cellular

networks available in your area.

If you select Manual, you can select a network that has a roaming agreement

with your home service provider. The phone stays in manual mode until

automatic mode is selected or another SIM card is inserted into the phone.

•

Confirm SIM service actions to confirm messages sent between your phone and

your service provider.

Accessing these services may involve sending a text message or making a

phone call. You may be charged for these services.

•

Help text activation to set the phone to show the help texts. See Using the

menu on page 45.

Start-up tone to set the phone to play a start-up tone when the phone is

switched on.

Enhancement settings

The enhancement settings menu is shown only if the phone has been or is

currently connected to a compatible mobile enhancement, such as the handsfree

unit.

Press Menu, and select Settings and Enhancement settings. You can select an

enhancement menu if the corresponding enhancement is or has been connected

to the phone. Depending on the enhancement, you can select options, for

example, a profile that can be activated automatically when you connect the

enhancement.

Configuration settings

You can configure your phone with settings that are required for certain services

to function correctly. The supported services are multimedia messaging, instant

messaging, synchronisation, e-mail application, streaming, push to talk, and

browser. Your service provider may also send you these settings. See

Configuration settings service on page 18.

For information on availability and the appropriate configuration settings,

contact your network operator or service provider.

Press Menu, and select Settings, and Configuration settings. Select from the

following list:

•

Default configuration sett., and the list of service providers saved in the phone

is shown. Scroll to a service provider, and press Details to view the applications

that the configuration settings of this service provider supports.

Press Options, and select Set as default to set the configuration settings of the

service provider as default settings. To delete configuration settings, select

Delete.

•

Activate default in all applications to activate the default configuration

settings for supported applications.

Preferred access point includes names of the saved access points. Scroll to an

access point, press Options, and select Details to view the name of the service

provider, data bearer, and GPRS access point or GSM dial-up number.

•

Personal configuration settings to add new personal accounts for various

services, and to activate or delete them.

To add new personal account if you have not added any, press Add new;

otherwise, press Options, and select Add new. Select the service type, and one

by one select and key in all the required parameters. The parameters differ

according to the selected service type.

100

To delete or activate a personal account, scroll to it, press Options, and select

Delete or Activate.

Security settings

When security features that restrict calls are in use (such as call barring, closed user group

and fixed dialing) calls still may be possible to the official emergency number programmed

into your device.

Security settings contains settings for access codes and other security features.

Press Menu, and select Settings and Security settings. Select from the following

settings:

•

PIN code request to set the phone to request your PIN code every time the

phone is switched on. Some SIM cards do not allow the PIN code request to be

turned off.

•

Call barring service (network service) to restrict calls

Fixed dialling to restrict your outgoing calls and text messages to selected

phone numbers if this function is supported by your SIM card.

When fixed dialing is on, (E)GPRS connections are not possible except while

sending text messages over a (E)GPRS connection. In this case, the recipient’s

phone number and the message centre number must be included on the fixed

dialing list.

•

Closed user group (network service) to specify the group of people whom you

can call and who can call you. For more information contact your network

operator or service provider.

101

•

Security level. Enter the security code, and select Phone to set the phone to ask

for the security code whenever a new SIM card is inserted into the phone.

Select Memory to set the phone to ask for the security code when the SIM card

memory is selected, when you change the memory in use, or copy from one

memory to another (Copying contacts on page 83).

Access codes to change the security code, PIN code, PIN2 code, or barring

password.

Restore factory settings

To reset some of the menu settings to their original values, press Menu, and select

Settings and Restore factory settings. Key in the security code and press OK.

The data that you have keyed in or downloaded is not deleted, for example, the

names and phone numbers saved in Contacts.

■ Gallery

You can save images and ringing tones that, for example, have been

received in multimedia messages in the folders of the gallery.

The phone supports the following file formats:

• Picture: JPEG, GIF, WBMP, BMP, OTA-BMP, and PNG

• Sound: scalable polyphonic MIDI (SP-MIDI), MP3, AAC AMR, and monophonic

ringing tones

• Video clip: 3GP format (H.263 baseline and MPEG-4 simple profile)

102

The phone may not support all variations of the file formats.

Your phone supports a Digital Rights Management (DRM) system to protect

acquired content. A piece of content, for example a ringing tone, can be protected

and associated with certain usage rules, for example the number of usage times

and a certain usage period. The rules are defined in the content’s activation key

which can be delivered either together with the content or independently

depending on the service provider. You may be able to update these activation

keys. Always check the delivery terms of any content and activation key before

acquiring them, as they may be subject to a fee.

being copied, modified, transferred or forwarded.

1. Press Menu, and select Gallery.

2. Scroll to the desired folder, and press Open to view the files in the folder, or

press Options to select an option for the folder:

•

Add folder, Delete folder, Move, Rename folder, Details, Type of view, or

Sort. You cannot delete, rename, or move the original folders on the phone.

Downloads to download more images and tones.

To check the availability of different services, pricing, and tariffs, contact

your network operator or service provider. Download content only from

sources you trust.

•

Memory status to view the memory consumption information of the phone.

Activation key list to view the list of all available activation keys. You can

delete the expired activation keys, for example.

103

3. If you opened a folder, scroll to the desired file.

To view the file, press Open, or to send the file using MMS, press the call key

. The phone can play video clips in 3GP format (H.263 baseline and MPEG-

4 simple profile), and short MP3 and AAC audio clips.

Press Options and select the option that you want from the list.

■ Media

Camera

You can take photos or record video clips with the built-in camera. The camera

lens is on the fold of the phone, and the main or mini display of the phone works

as a viewfinder. The camera produces images in JPEG format and the video clips in

H.263 (SubQCIF) format.

If there is not enough memory to take a new photo, you need to free some by

deleting old photos or other files in the gallery.

Taking a photo

1. To open the camera viewfinder, press Menu, and select Media, and Camera.

To open the viewfinder options, press Options, and you can, for example, select

to change the operation mode, zoom the image, and access the gallery or the

camera settings. For one photo at a time you can also activate the self-timer or

select to use the mini display as the viewfinder.

2. To take a photo, press Capture. The phone saves the photo in the Images folder

of the Gallery menu.

104

3. Press Back to take another photo, or Send the photo. Press Options, and select

from the list of options.

Recording a video clip

1. Press Menu, and select Media, and Camera. Press Options, and select Change

mode and Video.

2. To start recording a video clip, press Record. To pause the recording, press

Pause, and to resume the recording, press Continue.

3. To stop the recording, press Stop. The phone saves the recording in the Video

clips folder of the Gallery menu.

Press Play to view the recording, or press Options, and select, for example, an

option to delete or rename the saved video clip, send it as a multimedia

message or using an IR connection, or access the gallery.

Camera settings

Press Menu, and select Media, and Camera. Press Options, and select Settings and

an option from the list. You can define the image quality, set the length of the

video clips, the camera sounds, and default title and default mode.

Media player

With the media player you can view, play, and download files, for example images,

audio, video, and animated images from different kinds of sources. In addition it

allows you to see compatible streaming videos from a network server (network

service).

105

Press Menu, and select Media and Media player. Select Open gallery, Bookmarks,

Go to address, or Media downloads.

Setting up the phone for a streaming service

You may receive the configuration settings required for the streaming as a

configuration message from the network operator or service provider. See

Configuration settings service on page 18.

To key in the settings manually, see Configuration settings on page 99.

Press Menu, and select Media, Media player and Streaming sett..

• Select Configuration. Only the configurations that support streaming are

shown. Select a service provider, Default, or Personal config. for streaming. You

may receive the streaming settings as a configuration message, see

Configuration settings service on page 18. To key in the configuration settings

manually, see Configuration settings on page 99.

• Select Account and a streaming service account contained in the active

configuration settings.

Radio

The FM radio uses the wire of the headset as an antenna. A compatible headset needs to be

attached to the device for the FM radio to function properly.

Warning: Listen to music at a moderate level. Continuous exposure to high

volume may damage your hearing.

The quality of the radio broadcast depends on the radio station’s coverage in that

particular area.

106

1. To turn on the radio, press Menu, and select Media and Radio.

2. If you have saved radio channels, scroll to the channel you want to listen to, or

select a radio channel location 1 to 9 by pressing the corresponding number

key.

When using the compatible headset supplied with the headset key, press the

key to scroll to the desired saved radio channel.

3. To turn off the radio, press Options, and select Switch off, or press and hold

You can close the fold of the phone while listening to the radio.

You can make a call or answer an incoming call normally while listening to the

radio. The volume of the radio is muted. When you end the call, the radio volume

will automatically be turned up again.

When an application using a (E)GPRS or HSCSD connection is sending or receiving

data, it may interfere with the radio.

Tuning a radio channel

When the radio is on, press and hold the scroll key down or up to start the channel

search. Searching stops when a channel is found. To save the channel, press Save,

or press Options, and select Save channel. Key in the name of the channel, and

press OK. Select the location where you want to save the channel.

Using the loudspeaker

Warning: Do not hold the device near your ear when the loudspeaker is in use,

because the volume may be extremely loud.

107

When the radio is on, press Options, and select Loudspeaker to listen to the radio

using the loudspeaker. Keep the headset connected to the phone.

Voice recorder

You can record speech, sound, or an active call for up to 3 minutes. You can also

set a recording as a ringing tone.

The recorder cannot be used when a data call or GPRS connection is active.

Recording

1. Press Menu, select Media and Voice recorder.

2. To start the recording, select Record. To start recording a call, press Options,

and select Record. While recording a call, hold the phone in the normal

position near to your ear. All parties to the call will hear a faint beep

approximately every 5 seconds.

3. To end the recording, press Stop. The recording will be saved in the Recordings

folder of the Gallery menu.

To open the list of the saved recordings, select Recordings list. Open the

Recordings folder and the recording that you want to listen to.

To listen to the latest recording, select Play last recorded.

To send the latest recording using multimedia messaging or infrared, select

Send last recorded.

108

■ Push to talk

Push to talk over cellular (PTT) is a two-way radio service available over a

GSM/GPRS cellular network (network service). Push to talk provides

direct voice communication connected with the push of the PTT key.

You can use push to talk to have a conversation with one person or with a group

of people having compatible devices. When your call is connected, the person or

group you are calling does not have to answer the phone. Besides the GPRS

counters, the phone registers only one-to-one calls in the recent call lists in Call

where appropriate as there is no other confirmation whether the recipient(s) have

heard the call.

To check availability and costs, and to subscribe to the service, contact your

network operator or service provider. Roaming services may be more limited than

for normal calls.

Before you can use the push to talk service, you must define the required push to

talk service settings.

While you are connected to the push to talk service, you can use the other

functions of the phone. The push to talk over cellular service is not connected to

traditional voice communication, and therefore many of the services available for

traditional voice calls (for example, voice mailbox) are not available for push to

talk over cellular communications.

109

Opening the push to talk menu

Press Menu, and select Push to talk.

• To connect to or disconnect from the push to talk service, select Switch PTT on

or Switch PTT off.

• To view the received callback requests, select Callback inbox.

• To view the list of push to talk groups, select Group list.

• To view the list of contacts to which you have added the push to talk address,

select Contacts list.

• To add a new push to talk group to the phone, select Add group.

• To set the push to talk settings for use, select PTT settings.

• To set the required settings for the push to talk connection, select

Configuration settings.

• To open the browser and to connect to the push to talk network portal

provided by the service provider, select Services.

Connecting to and disconnecting from the push to talk service

To connect to the push to talk service, press Menu, and select Push to talk, and

Switch PTT on. indicates the push to talk connection.

indicates that the

service is temporarily unavailable. The phone automatically tries to reconnect to

the service until you disconnect from the push to talk service. If you have added

group(s) to the phone, you are automatically joined to the active (Default or

Listened) groups, and the name of the default group is displayed in standby mode.

110

To disconnect from the push to talk service, select Switch PTT off.

Callback requests

If you make a one-to-one call and do not get a response, you can send a request

for the person to call you back.

When someone sends you a callback request, Callback request received is

displayed in standby mode. When you receive a callback request from someone

who is not in your contacts list, you can save the name to your contacts.

Sending a callback request

• To send a callback request from the contacts list in the Push to talk menu,

select Contacts list. Scroll to a contact, press Options, and select Send

callback.

• To send a callback request from the Contacts, press the scroll key down in

standby mode, and scroll to the desired contact. Press Details, scroll to the

push to talk address, press Options, and select Send callback.

• To send a callback request from the group list in the Push to talk menu, select

Group list, and scroll to the desired group. Press Options, select Active

members, scroll to the desired contact, press Options, and select Send callback.

• To send a callback request from the callback request list in the Push to talk

menu, select Callback inbox. Scroll to a contact, press Options, and select Send

callback.

111

Responding to a callback request

1. To open the Callback inbox, press View. The list of nicknames of the persons

who have sent you callback requests is shown.

2. To make a one-to-one call, press the PTT key.

3. To send a call request back to the sender, press Options, and select Send

callback.

To delete the request, press Delete.

Saving the callback request sender

1. To open the Callback inbox, press View. The list of nicknames of the persons

who have sent you callback requests is shown.

2. To view the sender's push to talk address, press Options, and select View PTT

address.

To save a new contact or to add the push to talk address to a contact, press

Options, and select Save as or Add to contact.

Making and receiving a push to talk call

Set the phone to use either loudspeaker or earpiece for push to talk

communication. When the earpiece is selected, you can use the phone normally to

your ear.

Warning: Do not hold the device near your ear when the loudspeaker is in use,

because the volume may be extremely loud.

112

When connected to the push to talk service, you can make or receive group calls or

one-to-one calls. One-to-one calls are calls you make to only one person, instead

of a group.

Making a group call

To make a call to the default group, press the PTT key. A tone sounds indicating

that the access is granted, and the phone displays your nickname and group name.

To make a call to a nondefault group, select Group list in the push to talk menu,

scroll to the desired group, and press the PTT key.

Press and hold the PTT key the entire time you are talking, and hold the phone in

front of you so that you can see the display. When you have finished, release the

PTT key. Talking is allowed on a first-come, first-served basis. When someone

stops talking, the first person to press the PTT key can talk next.

Making a one-to-one call

• To start a one-to-one call from the list of contacts to which you have added

the push to talk address received from the service provider, select Contacts list.

Scroll to a contact, and press the PTT key.

You can also select the contact from the Contacts list.

• To start a one-to-one call from the list of push to talk groups, select Group list,

and scroll to the desired group. Press Options, select Active members, scroll to

the desired contact, and press the PTT key.

• To start a one-to-one call from the list of callback requests you have received,

select Callback inbox. Scroll to the desired nickname, and press the PTT key.

113

Receiving a group or a one-to-one call

A short tone notifies you of an incoming group and one-to-one call. When

receiving a group call, the group name and the nickname of the caller are

displayed. When receiving a one-to-one call from a person whose information

you have saved in Contacts, the saved name is displayed if identified; otherwise,

only the nickname of the caller is displayed.

You can either accept or reject an incoming one-to-one call if you have set the

phone to first notify you of the one-to-one calls.

If you press the PTT key to try to respond to a group while another member is

talking, you hear a queuing tone and Queuing is displayed as long as you press the

PTT key. Press and hold the PTT key, and wait for the other person to finish, then

you can talk.

Adding one-to-one contact

You can save the names of persons to whom you often make one-to-one calls.

• To add a push to talk address to a name in the Contacts:

Press the scroll key down in standby mode, scroll to the desired contact, and

press Details. Press Options and select Add detail and PTT address.

• To add a contact to the push to talk contacts list:

To add the push to talk contact, open the push to talk menu, and select

Contacts list. Press Options, and select Add contact.

• To add a contact from the group list:

114

When connected to the push to talk service, select Group list, scroll to the

desired group, and press Options. Select Active members, scroll to the member

whose contact information you want to save, and press Options. Select Save as

to add a new contact, or Add to contact to add a push to talk address to a name

in the Contacts.

Creating and setting up groups

When you call a group, all members joined to the group hear the call

simultaneously.

Each member in the groups is identified by a nickname, which is shown as a caller

identification. Group members can choose a nickname for themselves in each

group.

Groups are registered with a URL address. One user registers the group URL in the

network by joining the group session the first time.

There are three types of push to talk groups:

• Provisioned groups are closed groups that allow only selected participants

provisioned by the service provider to join in the groups.

• Ad hoc groups are groups that the users can create. You can create your own

group, and invite members to the group.

• Ad hoc pro groups are groups you can create from members in a provisioned

group. For example, a business can have a closed group, plus separate groups

created for certain business functions.

115

Adding a group

1. Press Menu, and select Push to talk, Add group, and Guided.

2. To set the security level for the group, select Open group or Secured group.

If you select Secured group, the phone automatically creates a scrambled part

to the group address that the members cannot view when they receive the

invitation to the group. Only the person who creates the secured group, can

invite more members to the group.

3. Key in the name for the group, and press OK.

4. Select the status for the group: Default, Listened, or Inactive. The phone

indicates that the group is saved and its status. Default and Listened are active

groups. When you press the PTT key to make a group call, the default group is

called if you have not scrolled to any other group or contact.

5. To send an invitation to the group, press Yes when the phone requests for

sending an invitation. You can send the invitation using a text message or

infrared.

The members you invite to the open groups can also invite more members to

the group.

Receiving an invitation

1. When you receive a text message invitation to a group, Group invitation

received: is displayed.

2. To view the nickname of the person who sent the invitation and the group

address if the group is not a secured group, press View.

116

3. To add the group to your phone, press Save, and to set the status for the group,

select Default, Listened, or Inactive.

To reject the invitation, press Exit and Yes, or press View , Discard, and Yes.

Settings for push to talk

There are two kinds of push to talk settings: settings for use and for connecting to

the service.

You may receive the settings for connecting to the service as a configuration

message from your network operator or service provider, see Configuration

settings service on page 18. To key in the settings manually, see Configuration

settings on page 99.

To access the settings for connecting to the service, press Menu, and select Push

to talk, and Configuration settings. Select from following:

•

Configuration. Only the configurations that support the push to talk service

are shown. Select a service provider, or Default, or Personal config. for push to

talk service. You may receive the push to talk settings as a configuration

message, see Configuration settings service on page 18. To key in the

configuration settings manually, see Configuration settings on page 99.

•

Account and select a push to talk service account contained in the active

configuration settings.

117

• Select one by one to set the following: PTT user name, Default nickname, PTT

password, Domain, and Server address .

To access the push to talk settings for use, press Menu, and select Push to talk, and

PTT settings. Select from following:

•

1 to 1 calls and On to select the phone to allow the reception of incoming one-

to-one calls. If you select Off, you can make but not receive one-to-one calls.

The service provider may offer some services that override these settings.

1 to 1 calls and Notify to set the phone to first notify you of incoming one-to-

one calls with a ringing tone.

•

Listened groups and On to activate the listened groups.

PTT status in startup and Yes to set the phone to automatically connect to the

push to talk service when you switch the phone on.

•

Send my PTT address and No to hide your push to talk address from group and

one-to-one calls.

■ Organiser

Alarm clock

The alarm clock works if you close the fold or even when the phone is switched off

if there is enough power in the battery.

Press Menu, and select Organiser and Alarm clock.

118

• Select Alarm time, and if the alarm time is not set, key in the alarm time, and

press OK. Otherwise, to change the alarm time, select On.

• Select Repeat alarm and Repetition days. Mark the days when you want the

alarm to be repeated, and press Done.

• Select Alarm tone to set a tone for the alarm.

To select the radio as an alarm tone, connect the headset to the phone. The

channel most recently selected is the alarm tone. The radio alarm is played

through the loudspeaker even though the headset is connected. If the headset

is removed, the default alarm tone replaces the radio.

When the alarm time expires

If the alarm time is reached while the device is switched off, the device switches itself on

and starts sounding the alarm tone. If you press Stop, the device asks whether you want to

activate the device for calls. Press No to switch off the device or Yes to make and receive

calls. Do not press Yes when wireless phone use may cause interference or danger.

When the alarm time is reached while the phone is switched on, the phone sounds

an alert tone, flashes Alarm!, and shows the current time. To turn off the alarm,

press Stop. To stop the alarm for 10 minutes, press Snooze or any key except Stop.

When the fold is closed, press either of the volume keys to switch the alarm clock

to snooze.

119

Calendar

You can track appointments, meetings, birthdays, anniversaries, and other events,

and set a calendar alarm as a reminder.

Press Menu, and select Organiser and Calendar. Scroll to the day that you want.

The current day is indicated by a frame around it. If any notes are set for the day,

the day is shown in bold.

• If you press View, you can view the day notes.

• To view a single note, scroll to the note that you want to view, and press

View. The note view allows you to view the details of the selected note. You

can scroll through the note. When you have set the alarm for the note, the

indicator is displayed.

• Press Options and there are, for example, options for making a note, or for

sending a note using IR, or as a note directly to another compatible phone

calendar, or as a text or multimedia message.

Settings to set, for example, the date, time, date or time format, or the first

day of the week. In the Auto-delete option you can set the phone to delete

old notes automatically after a specified time. However, the repeated notes,

for example, birthday notes, will not be deleted.

• If you press Options, you can select Week view to view a week. There are also,

for example, options for making a note, accessing the to-do list, or deleting all

notes in calendar, or selecting settings.

120

Note alarm

The phone beeps, and displays the note. With a call note

can call the displayed number by pressing the call key

on the display, you

• To stop the alarm and to view the note, press View. Press Snooze and the

phone returns to standby mode.

• To stop the alarm without viewing the note, press Exit.

When the fold is closed, press either of the volume keys to mute the note alarm.

To-do list

You can save a note for a task, select a priority level for the note, and mark it as

done when you have completed the task. You can sort the notes by priority or by

date.

Press Menu, and select Organiser and To-do list.

To add a new note when the note list is empty, press Add note, or if you have

saved notes, press Options, and select Add. Key in the note and press Save. Select

the priority for the note. The phone automatically sets the deadline without an

alarm for the note. To change the deadline, view the note and select the option for

deadline.

Notes

You can write and send notes to compatible devices with infrared, text messaging,

or multimedia messaging.

121

To access Notes, press Menu, and select Organiser and Notes. To add a note if the

list of notes is empty, press Add note. Otherwise, press Options, and select Make a

note. Key in the note and press Save.

• To view a note, scroll to it, and press View.

To edit the note, press Edit. While editing a note, press Options and you can

select, for example, to add date and time to the note. Select Close to exit the

text editor without saving the changes.

• Press Options, and you can, for example, send the note to a compatible device

using IR or as a text or multimedia message. If the note is too long to be sent as

a message, the phone will ask you to delete the appropriate number of

characters from your note.

Synchronisation

Synchronisation allows you to save your calendar and contacts data on a remote

Internet server (network service) or on a compatible PC. If you have saved data on

the remote Internet server, you can synchronise your phone by starting the

synchronisation from the phone. Synchronising to the remote server is a network

service. You can also synchronise the data in your phone contacts and calendar to

correspond with the data of a compatible PC by starting the synchronisation from

the PC. The contact data in your SIM card will not be synchronised.

Answering an incoming call during synchronisation will end the synchronisation

and you must restart it.

122

Synchronising from your phone

Before synchronising from your phone, you may need to do the following:

• Subscribe to a synchronisation service. For more information on availability

and the synchronisation service settings, contact your network operator or

service provider.

• Retrieve the synchronisation settings from your network operator or service

provider, see Settings for synchronisation on page 123.

To start the synchronisation from the phone:

1. Select the configuration settings you need for the synchronisation. See

Settings for synchronisation on page 123.

2. Press Menu, select Organiser, Synchronisation, Server sync, and Data to be

synchronised. Mark the data to be synchronised.

3. Press Menu, and select Organiser, Synchronisation, Server sync, and

Synchronise. The marked data of the active set will be synchronised after

confirmation.

Synchronising for the first time or after an interrupted synchronisation may

take up to 30 minutes to complete if the contacts or calendar are full.

Settings for synchronisation

You may receive the configuration settings required for synchronisation as a

configuration message from the network operator or service provider. To manage

all the configuration settings, see Configuration settings on page 99.

1. Press Menu, select Organiser, and Synchronisation.

123

2. Select Server sync, and Sync settings.

• Select Configuration. Only the configurations that support the

synchronisation are shown. Select a service provider, Default, or Personal

config. for synchronisation. You may receive the synchronisation settings

as a configuration message, see Configuration settings service on page 18.

To key in the configuration settings manually, see Configuration settings on

page 99.

Select Account and a synchronisation service account contained in the

active configuration settings.

3. Select PC sync settings to key in the settings for server alerted synchronisation.

Select to set User name and Password.

The user name and password have to be the same in the phone and in the PC.

Synchronising from a compatible PC

To synchronise the contacts and calendar from the PC, use an IR connection or a

data cable. You also need the PC Suite software of your phone installed on the PC,

refer to PC Connectivity on page 144. Start the synchronisation from the PC using

PC suite.

Wallet

In Wallet you can save personal information such as credit card numbers, user

names, or passwords. You can easily retrieve data and automatically fill in data

fields while you are making purchases online.

124

The data saved in the wallet is protected with a wallet code that you can define

when you access wallet for the first time. At Create wallet code: key in the code,

and press OK. At Verify wallet code: key in the code again, and press OK.

To delete the wallet code and all contents of the wallet, key in *#7370925538#

(*#res wallet# in letters) in standby mode. You also need the phone security code.

To add or edit the content of the wallet, access the wallet menu. To use the

content of the wallet in a mobile service, access the wallet from the browser, see

Web on page 132.

Accessing the wallet menu

To access the wallet menu, press Menu, select Organiser and Wallet. Key in your

wallet code, and press OK. Select from the following:

•

Wallet profiles to create card combinations for different services. You can

select the appropriate wallet profile when the service requires you to fill in

many data items.

•

Cards to save personal card information.

Tickets to save the notifications of e-tickets that you have bought. To view the

tickets, press Options, and select View.

•

Receipts to save receipts of purchases.

Personal notes to save personal information that you want to keep protected

by using the wallet PIN code.

•

Settings to change the wallet code, and set the RFID (radio frequency

identification) code.

125

Saving card details

1. Access the wallet, and select Cards and the card type to save details.

2. If no card is added, press Add new. Otherwise, press Options, and select Add

new. Fill in the fields with details.

If your service provider supports over the air services, you may receive card

information to your phone. The notification tells you to which category the card

belongs. Save or discard the received card. You can view and rename the card, but

you cannot edit it. For availability of receiving card information over the air,

contact the card issuer or service provider.

Personal notes

You can add personal notes to save account numbers, codes, or notations.

Access the wallet, and select Personal notes.

• To create a personal note if no note is added, press Add new; otherwise, press

Options, and select Add new.

• To view a note, scroll to the desired note, and press View.

• To edit the displayed note, press Options, and select Edit.

While viewing a note, press Options. Select Delete to delete the note, Send via

text msg. to copy the note as a text message, and Copy to calendar to copy the

note to the calendar as a memo. Use detail is used to extract numbers, e-mail

addresses, and web addresses from a note.

126

Creating a wallet profile

When you have saved your personal card details, you can combine them into a

wallet profile. Use the profile to retrieve wallet data from different cards while

browsing.

1. Access the wallet, and select Wallet profiles.

2. To create a new wallet profile if no profile is added, press Add new; otherwise,

press Options, and select Add new.

3. Select the desired information one by one from the wallet cards, and when

Wallet profile name: is displayed, enter a name for the new profile.

Wallet settings

Access the wallet, and select Settings. Select Change code to change the wallet

code, and RFID to set the RFID code.

Calculator

Press Menu, and select Organiser and Calculator.

When 0 is displayed, key in the first number in the calculation. Press

for a

decimal point. Alternatively, press

divide.

repeatedly to add, subtract, multiply, or

For a total, press Equals.

Note: This calculator has limited accuracy and is designed for simple calculations.

To start a new calculation, first press and hold Clear.

127

Performing a currency conversion

Press Menu, and select Organiser and Calculator. To save the exchange rate, press

Options, and select Exchange rate. Select either of the displayed options, key in

the exchange rate, and press OK. The exchange rate remains in the memory until

you replace it with another one. Key in the amount to be converted, press Options,

and select In domestic or In foreign.

You can also perform the currency conversion in standby mode.

Note: When you change base currency, you must key in the new rates because all

previously set exchange rates are set to zero.

Stopwatch

You can measure time and take intermediate times or lap times using the

stopwatch. During timing, the other functions of the phone can be used. To set the

stopwatch timing in the background, press

Using the stopwatch or allowing it to run in the background when using other features

increases the demand on battery power and reduces the battery life.

Press Menu, and select Organiser andStopwatch.

• To take intermediate times, select Split timing. To start the time observation,

press Start. Press Split every time that you want to take an intermediate time.

To stop the time observation, press Stop. To set the stopwatch timing in the

background, press

• To take lap times, select Lap timing. To set the stopwatch timing in the

background, press

128

• To view the timing that you have set in the background, select Continue.

• To view the most recently measured time if the stopwatch is not reset, select

Show last.

• To view or delete the saved times, select View times or Delete times.

Countdown timer

You can set the timer to measure countdown time.

Press Menu, and select Organiser and Countdown timer.

To set the time, key in the alarm time in hours, minutes, and seconds, and press

OK. If you wish, write a note, which is displayed when the time expires. Press Start

to start the countdown timer.

To change the countdown time, select Change time, or to stop the timer, select

Stop timer.

Tip: To start the countdown timer or to change the time in standby mode,

key in the time in hours, minutes, and seconds, press Options, and select

Countdown timer. If the time is correct, press Start.

If the alarm time is reached when the phone is in standby mode, the phone sounds

a tone and flashes the note or Countdown time up. To stop the alarm, press any

key. If no key is pressed, the alarm automatically stops within 30 seconds. To stop

the alarm and delete the text note, press Exit. To restart the countdown timer,

press Restart.

When the fold is closed, press either of the volume keys to mute the alarm.

129

■ Applications

In the Games and Collection folders you can use and manage the Java

games and applications installed in the phone.

Games

Press Menu, and select Applications and Games.

• To select and open a game, scroll to the game, and press Open or the call key

. For options, press Options, and see Options available for an application

on page 131.

• Press Options, and to download a game to the phone, select Downloads and

Game downloads. You must have the configuration settings for the browser set

in your phone to use the downloading. See Configuration settings on page 99.

To set sounds, lights, and shakes for the game, select App. settings.

Running some games may consume battery power faster (you may need to

connect the phone to the charger).

Collection

Press Menu, and select Applications and Collection.

• To select and open an application, scroll to the application, and press Open or

the call key

. For options, press Options, and see Options available for an

application on page 131.

130

• Press Options, and to download an application to the phone, select Downloads

and App. downloads. You must have the configuration settings for the browser

set in your phone to use the downloading. See Configuration settings on page

99.

To set sounds, lights, and shakes for the application, select App. settings.

Running some applications may consume battery power faster (you may need to

connect the phone to the charger).

Options available for an application

•

Delete to delete the application or application set from the phone.

Details to give additional information about the application.

Update version to check if a new version of the application is available for

download from the services (network service).

•

Web page to provide further information or additional data for the application

from an Internet page. This feature needs to be supported by the network. It is

only shown if an Internet address has been provided with the application.

App. access to control an application’s access to functions that may require

your acknowledgement before use, for example, network access.

Downloading a game or an application

Your phone supports J2ME^TMJava applications. During downloading, the

compatibility is checked, and the downloading is interrupted, for example, if the

phone does not support the application.

131

Important: Only install applications from sources that offer adequate protection

against harmful software.

You can download new Java applications in different ways:

• Press Menu, and select Applications. Press Options, and select Downloads

andGame downloads or App. downloads.

The list of available bookmarks is shown. Select More bookmarks to access the

list of bookmarks in the Web menu, see Bookmarks on page 137.

Select the appropriate bookmark to connect to the desired site.

To check the availability of different services, pricing and tariffs, contact your

network operator or service provider.

• Press Menu, and select Web and Download links. See Downloading on page

138.

Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does

not warrant or endorse these sites. If you choose to access them, you should take the same

precautions, for security or content, as you would with any Internet site.

■ Web

You can access various services with your phone browser. These services

may include, for example, weather reports, news, or flight times and

financial information.

Check the availability of these services, pricing and tariffs with your network

operator or the service provider whose service you wish to use. Service providers

will also give you instructions on how to use their services.

132

With your phone browser, you can view the services that use Wireless Mark-Up

Language (WML) or extensible HyperText Mark-up Language (XHTML) on their

pages. The appearance of the pages may vary due to the limited size of the phone

display. You may not be able to view all of the page details.

Basic steps for accessing and using services

1. Save the configuration settings that are required to access the service that you

want to use.

2. Make a connection to the given service.

3. Start browsing the pages of the service.

4. Once you are finished browsing, end the connection to the service.

Setting up browsing

You may receive the configuration settings required for browsing as a

configuration message from the network operator or service provider that offers

the service that you want to use. See Configuration settings service on page 18.

To manage all the configuration settings, see Configuration settings on page 99.

Connecting to a service

Firstly, ensure that the correct configuration settings of the service that you want

to use are activated.

• Press Menu, and select Web, Settings and Configuration settings.

133

• Select Configuration. Only the configurations that support browsing

service are shown. Select a service provider, Default, or Personal config. for

browsing. You may receive the browser settings as a configuration

message, see Configuration settings service on page 18. To key in the

configuration settings manually, see Configuration settings on page 99.

Select Account and a browsing service account contained in the active

configuration settings.

•

Display terminal window and select Yes to perform manual user

authentication for intranet connections.

Secondly, make a connection to the service, for example, press Menu, and select

Web and Home, or in standby mode, press and hold

Browsing the pages

After you connect to a service, you can start browsing its pages. The function of

the phone keys may vary in different services. Follow the text guides on the phone

display. For more information, contact your service provider.

If GPRS is selected as the data bearer, the

the display during browsing. If you receive a call or a text message, or make a call

during an (E)GPRS connection, the indicator will be shown on the top right of

indicator is shown on the top left of

the display to indicate that the (E)GPRS connection is suspended (on hold). After a

call, for example, the phone tries to reconnect the (E)GPRS connection.

134

Browsing with phone keys

• Use any of the scroll keys to browse through the page.

• To select a highlighted item, press the call key

link.

, or press Select to open the

• To enter letters and numbers in the text editor, press

to . To enter

special characters, press

Options while browsing

Press Options and the following options may be available. The service provider

may also offer other options.

•

Use wallet info to use the wallet card information from the Wallet application

if the service page supports the wallet. Refer to Wallet on page 124.

•

Shortcuts to open a new list of options that are specific to the page.

Home to return to the homepage of the service provider.

Add bookmark to save the page as a bookmark.

Bookmarks. See Bookmarks on page 137.

Download links to show the list of bookmarks for downloading.

Other options to show a list of other options, for example options for the wallet

and some security options.

•

Reload to reload and update the current page.

Quit. See Quit browsing on page 136.

135

Direct calling

The browser supports functions that you can access while browsing. You can make

a voice call, send DTMF tones while a voice call is in progress, and save a name and

a phone number from a page.

Quit browsing

To quit browsing and end the connection, press Options, and select Quit. When

Quit browsing? is shown, press Yes.

Alternatively, press

twice, or press and hold

Appearance settings of the browser

While browsing, press Options and select Other options and Appear. settings, or in

standby mode, press Menu, and select Web, Settings and Appearance settings.

Select

•

Text wrapping and On, and the text continues on the next line. Select Off, and

the text will be abbreviated.

•

Font size and select Extra small font, Small or Medium.

Show images and select No if you do not want the pictures on the page to be

shown. This can speed up the browsing of pages that contain a lot of pictures.

•

Alerts and select Alert for unsecure connection and Yes to set the phone to

alert when a secure connection changes to an unsecure one during browsing.

Select Alert for unsecure items and Yes to set the phone to alert when a

secured page contains an unsecure item.

136

•

Character encoding and Content encoding to select the encoding for the

browser page content.

Select Unicode (UTF-8) web addresses and On if you want the phone to send an

URL as an UTF-8 encoding.

Bookmarks

You can save page addresses as bookmarks in the phone memory.

1. While browsing, press Options and select Bookmarks, or in standby mode,

press Menu, and select Web and Bookmarks.

2. Scroll to a bookmark, and press Select or the call key

to make a

connection to the page associated with the bookmark.

Press Options, and select, for example, to view, edit, delete, or send the

bookmark.

Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does

not warrant or endorse these sites. If you choose to access them, you should take the same

precautions, for security or content, as you would with any Internet site.

Receiving a bookmark

When you have received a bookmark (sent as a bookmark) 1 bookmark received is

displayed. Press Show and Save to save the bookmark, or press Options, and select

View or Delete to view or delete it.

137

Downloading

To download more tones, images, games or applications to your phone while

browsing, press Options, and select Download links, or in standby mode, press

Menu, and select Web and Download links. Select to download tones, images,

games, video clips, themes, or applications.

Note: Only install software from sources that offer adequate protection against

viruses and other harmful software.

Service inbox

The phone is able to receive service messages (pushed messages) from your service

provider. Service messages may be notifications of, for example, news headlines,

and they may contain a text message or an address of a service.

• To view a received service message, press Show. If you press Exit, the message

is moved to the Service inbox. To access the Service inbox later, press Menu,

and select Web, and Service inbox.

• To manage a service message while browsing, press Options, and select Other

options and Service inbox. Scroll to the message that you want, and press

Retrieve to download the marked content from the page, or press Options, and

select Details or Delete.

Service inbox settings

Press Menu, and select Web, Settings and Service inbox settings.

• To set the phone to receive (or reject) service messages, select Service

messages, and On (or Off).

138

• To set the phone to receive messages only from content authors approved by

the service provider, select Message filter and On. To view the list of the

approved content authors, select Trusted channels.

• To automatically activate the browser when the phone has received a service

message in standby mode if you have set the phone to receive service

messages, select Automatic connection, and On.

If you select Off, the phone will activate the browser only after you select

Retrieve when the phone has received a service message.

The cache memory

A cache is a memory location that is used to store data temporarily. If you have tried to

access or have accessed confidential information requiring passwords, empty the cache

after each use. The information or services you have accessed is stored in the cache.

To empty the cache:

• while browsing, press Options, and select Other options, and Clear the cache;

• in standby mode, press Menu, and select Web, and Clear the cache.

A cookie is data that a site saves in your phone browser cache memory. The data

can be, for example, your user information or your browsing preferences. Cookies

will be saved until you clear the cache memory, see The cache memory on page

139.

139

1. While browsing, press Options, and select Other options, Security and Cookie

settings, or in standby mode, press Menu, and select Web, Settings, Security

settings and Cookies.

2. To allow or prevent the phone receiving cookies, select Allow or Reject.

Scripts over secure connection

You can select whether the scripts from a secure page are allowed to be run.

1. While browsing, press Options, and select Other options, Security, and select

Script settings, or in standby mode, press Menu, and select Web, Settings,

Security settings, and Scripts over secure connection.

2. To allow the scripts, select Allow.

Browser security

Security features may be required for some services, such as banking services or

shopping on a site. For such connections you need security certificates and

possibly a security module which may be available on your SIM card. For more

information, contact your service provider.

Security module

The security module can contain certificates as well as private and public keys. The

purpose of the security module is to improve security services for applications

requiring a browser connection, and to allow you to use a digital signature. The

certificates are saved in the security module by the service provider.

140

Press Menu, and select Web, Settings, Security settings and Security module

settings. Select

•

Security module details to show the security module title, its status,

manufacturer and serial number.

Module PIN request to set the phone to request the module PIN when using

services provided by the security module.

Change module PIN to change the module PIN, if allowed by the security

module.

Change signing PIN to select and change a signing PIN.