Nokia 6310i User Manual

Electronic user’s guide released subject to "Nokia User’s Guides Terms and Conditions, 7th June, 1998"

User´s Guide

9354260

Issue 3

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect

damages howsoever caused.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind, either express or

implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in

relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at

any time without prior notice.

The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you.

Contents

FOR YOUR SAFETY........................................................................................................................... 11

General information........................................................................................................................ 14

Stickers in the sales package ....................................................................................................................................................... 14

Access codes ..................................................................................................................................................................................... 14

Dynamic memory............................................................................................................................................................................. 15

Overview of the functions of the phone ....................................................................................... 16

Bluetooth ........................................................................................................................................................................................... 16

GPRS (General Packet Radio Service) ........................................................................................................................................ 16

HSCSD (High Speed Circuit Switched Data)............................................................................................................................ 17

WAP (Wireless Application Protocol)......................................................................................................................................... 18

JavaTM applications........................................................................................................................................................................ 18

Voice features................................................................................................................................................................................... 18

E-Mails................................................................................................................................................................................................ 19

1. Your phone................................................................................................................................... 20

Keys and connectors....................................................................................................................................................................... 20

Standby mode................................................................................................................................................................................... 21

2. Getting started............................................................................................................................. 23

Installing the SIM card and the battery.................................................................................................................................... 23

Charging the battery ...................................................................................................................................................................... 25

Switching the phone on and off ................................................................................................................................................. 25

Keypad lock (Keyguard).................................................................................................................................................................. 27

3. Call functions............................................................................................................................... 28

Making a call..................................................................................................................................................................................... 28

Last number redialling ................................................................................................................................................................ 28

Calling your voice mailbox......................................................................................................................................................... 29

Speed dialling a phone number................................................................................................................................................ 29

Making a conference call........................................................................................................................................................... 29

Answering or rejecting an incoming call .................................................................................................................................. 30

Call waiting.................................................................................................................................................................................... 30

Options during a call....................................................................................................................................................................... 31

4. Writing text ................................................................................................................................. 32

Using traditional text input .......................................................................................................................................................... 32

Using predictive text input............................................................................................................................................................ 33

Setting predictive text input on or off................................................................................................................................... 33

Writing words with predictive text input.............................................................................................................................. 34

Writing compound words ....................................................................................................................................................... 35

5. Phone book (Names) ................................................................................................................... 36

Selecting the phone book settings.............................................................................................................................................. 36

Saving names and phone numbers (Add name)...................................................................................................................... 37

Saving multiple numbers and text items per name............................................................................................................ 37

Changing the default number............................................................................................................................................... 38

Searching for a name in the phone book.................................................................................................................................. 38

Editing a name, number or a text item ..................................................................................................................................... 39

Erasing names and numbers......................................................................................................................................................... 39

Copying phone books...................................................................................................................................................................... 39

Sending and receiving a business card...................................................................................................................................... 40

Speed dialling.................................................................................................................................................................................... 41

Voice dialling .................................................................................................................................................................................... 41

Adding a voice tag....................................................................................................................................................................... 42

Making a call by using a voice tag ......................................................................................................................................... 43

Replaying, changing or erasing a voice tag.......................................................................................................................... 43

My numbers ...................................................................................................................................................................................... 43

Info numbers..................................................................................................................................................................................... 44

Service numbers............................................................................................................................................................................... 44

Caller groups..................................................................................................................................................................................... 44

6. Using the menu............................................................................................................................ 46

Accessing a menu function........................................................................................................................................................... 46

By scrolling..................................................................................................................................................................................... 46

By shortcut..................................................................................................................................................................................... 46

List of menu functions................................................................................................................................................................... 48

7. Menu functions............................................................................................................................ 50

Messages (Menu 1)......................................................................................................................................................................... 50

Writing and sending messages................................................................................................................................................. 50

Writing and sending e-mails .................................................................................................................................................... 51

Options for sending a message................................................................................................................................................ 52

Text and picture templates........................................................................................................................................................ 52

Inserting a text template in a text message or in an e-mail....................................................................................... 53

Inserting a picture template in a text message............................................................................................................... 53

Reading and replying to a message or an e-mail............................................................................................................... 53

Multipart messages ..................................................................................................................................................................... 54

Inbox and outbox folders........................................................................................................................................................... 55

Erasing the messages.................................................................................................................................................................. 55

Archive folder and My folders.................................................................................................................................................. 55

Voice messages............................................................................................................................................................................. 56

Info messages................................................................................................................................................................................ 56

Service command editor............................................................................................................................................................. 56

Message settings .......................................................................................................................................................................... 57

Call register (Menu 2)..................................................................................................................................................................... 57

Missed calls and received calls................................................................................................................................................. 58

Dialled numbers ............................................................................................................................................................................ 58

Erase recent call lists................................................................................................................................................................... 58

Call counters and call timers .................................................................................................................................................... 59

Profiles (Menu 3).............................................................................................................................................................................. 60

Settings (Menu 4)........................................................................................................................................................................... 61

Alarm clock..................................................................................................................................................................................... 61

Time and date settings................................................................................................................................................................ 61

Clock settings............................................................................................................................................................................. 61

Date settings .............................................................................................................................................................................. 62

Auto update of date and time............................................................................................................................................... 62

Call settings.................................................................................................................................................................................... 62

Call divert.................................................................................................................................................................................... 62

Anykey answer........................................................................................................................................................................... 63

Automatic redial........................................................................................................................................................................ 63

Speed dialling............................................................................................................................................................................. 63

Call waiting service .................................................................................................................................................................. 63

Summary after call ................................................................................................................................................................... 63

My number sending.................................................................................................................................................................. 64

Line for outgoing calls............................................................................................................................................................. 64

Phone settings............................................................................................................................................................................... 64

Language ..................................................................................................................................................................................... 64

Cell info display......................................................................................................................................................................... 64

Welcome note............................................................................................................................................................................ 65

Network selection..................................................................................................................................................................... 65

Confirm SIM service actions.................................................................................................................................................. 65

Help text activation................................................................................................................................................................. 65

Start-up tone............................................................................................................................................................................. 66

Tone settings ................................................................................................................................................................................. 66

Accessory settings........................................................................................................................................................................ 67

GPRS modem settings................................................................................................................................................................. 67

Security settings........................................................................................................................................................................... 68

Restore factory settings ............................................................................................................................................................. 69

Games (Menu 5)............................................................................................................................................................................... 70

Starting a game............................................................................................................................................................................ 70

Starting a 2-player game....................................................................................................................................................... 70

Game services and game settings........................................................................................................................................... 71

Applications (Menu 6).................................................................................................................................................................... 71

Launching an application .......................................................................................................................................................... 72

Other options available for each application or application set: ............................................................................... 72

Downloading an application..................................................................................................................................................... 73

Showing system information.................................................................................................................................................... 74

Calculator (Menu 7)........................................................................................................................................................................ 74

Making a currency conversion ................................................................................................................................................. 75

To-do list (Menu 8) ......................................................................................................................................................................... 76

Calendar (Menu 9)........................................................................................................................................................................... 77

Making a calendar note ............................................................................................................................................................. 78

When the phone alarms for a note......................................................................................................................................... 78

Infrared (Menu 10).......................................................................................................................................................................... 79

Bluetooth (Menu 11)...................................................................................................................................................................... 80

Activating and deactivating Bluetooth.................................................................................................................................. 80

Bluetooth device name........................................................................................................................................................... 80

Pairing with Bluetooth Passcode ......................................................................................................................................... 81

Bluetooth connection ................................................................................................................................................................. 81

Bluetooth settings ....................................................................................................................................................................... 82

Extras (Menu 12).............................................................................................................................................................................. 83

Voice recorder................................................................................................................................................................................ 83

Recording .................................................................................................................................................................................... 83

List of recordings....................................................................................................................................................................... 84

Voice commands........................................................................................................................................................................... 84

Wallet............................................................................................................................................................................................... 85

Storing personal card information....................................................................................................................................... 86

Personal notes............................................................................................................................................................................ 86

Wallet settings........................................................................................................................................................................... 87

Paying your purchases with wallet...................................................................................................................................... 87

Countdown timer.......................................................................................................................................................................... 87

Stopwatch....................................................................................................................................................................................... 88

Time observation and time splitting.................................................................................................................................... 88

Lap times ..................................................................................................................................................................................... 89

Viewing and erasing times ..................................................................................................................................................... 89

WAP services (Menu 13)................................................................................................................................................................ 89

Basic steps for accessing and using WAP services ............................................................................................................. 90

Setting up the phone for a WAP service................................................................................................................................ 90

Saving the service settings received as a text message ................................................................................................ 90

Keying in the service settings manually............................................................................................................................. 91

Making a connection to a WAP service ................................................................................................................................. 93

Browsing the pages of a WAP service.................................................................................................................................... 94

General guidelines for using the phone keys.................................................................................................................... 95

WAP direct calling........................................................................................................................................................................ 96

Ending a WAP connection.......................................................................................................................................................... 96

Appearance settings of the WAP browser............................................................................................................................. 96

Download settings........................................................................................................................................................................ 97

Bookmarks ...................................................................................................................................................................................... 97

Receiving a bookmark.............................................................................................................................................................. 98

Service inbox ................................................................................................................................................................................. 99

To set the phone to receive service messages.................................................................................................................. 99

The cache memory..................................................................................................................................................................... 100

Security indicator....................................................................................................................................................................... 100

Security module.......................................................................................................................................................................... 100

Digital signature ..................................................................................................................................................................... 101

Certificates ............................................................................................................................................................................... 101

Security module settings...................................................................................................................................................... 102

SIM services (Menu 14) ............................................................................................................................................................... 103

8. Data and fax communication ................................................................................................... 104

Communication applications and modem drivers................................................................................................................ 104

PC Suite......................................................................................................................................................................................... 104

Modem setup............................................................................................................................................................................... 105

GPRS - General Packet Radio Service............................................................................................................................... 105

HSCSD - High-Speed Circuit Switched Data.................................................................................................................. 105

Using data communication applications............................................................................................................................. 106

9. Battery statements..................................................................................................................... 107

Charging and Discharging........................................................................................................................................................... 107

CARE AND MAINTENANCE........................................................................................................... 108

IMPORTANT SAFETY INFORMATION............................................................................................ 109

FOR YOUR SAFETY

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given

in this manual.

Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or

danger.

ROAD SAFETY COMES FIRST

Don’t use a hand-held phone while driving.

INTERFERENCE

All wireless phones may get interference, which could affect performance.

SWITCH OFF IN HOSPITALS

Follow any regulations or rules. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT

Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING

Don’t use the phone at a refuelling point. Don’t use near fuel or chemicals.

SWITCH OFF NEAR BLASTING

Don’t use the phone where blasting is in progress. Observe restrictions, and follow any regulations or

rules.

USE SENSIBLY

Use only in the normal position. Don’t touch the antenna unnecessarily.

QUALIFIED SERVICE

Only qualified personnel may install or repair phone equipment.

ACCESSORIES AND BATTERIES

Use only approved accessories and batteries. Do not connect incompatible products.

WATER-RESISTANCE

Your phone is not water-resistant. Keep it dry.

BACKUP COPIES

Remember to make backup copies of all important data.

CONNECTING TO OTHER DEVICES

When connecting to any other device, read its user’s guide for detailed safety instructions. Do not

connect incompatible products.

CALLING

Ensure the phone is switched on and in service. Enter the phone number, including the area code, then

press

. To end a call, press

. To answer a call, press

EMERGENCY CALLS

Ensure the phone is switched on and in service. Press

as many times as needed (e.g. to exit a

call, to exit a menu, etc.) to clear the display. Enter the emergency number, then press

your location. Do not end the call until told to do so.

. Give

■ Network Services

The wireless phone described in this guide is approved for use on the GSM 900, GSM 1800 and GSM 1900 networks.

A number of features included in this guide are called Network Services. These are special services that you arrange

through your wireless service provider. Before you can take advantage of any of these Network Services, you must

subscribe to them through your service provider and obtain instructions for their use from your service provider.

Note: Some networks may not support all language-dependent characters and/or services.

Check the model number of any charger before use with this device. This device is intended for use when

supplied with power from ACP-7, ACP-8, ACP-12 and LCH-9.

Warning: Use only batteries, chargers and accessories approved by the phone manufacturer for use with

this particular phone model. The use of any other types may invalidate any approval or warranty applying

to the phone, and may be dangerous.

For availability of approved accessories, please check with your dealer.

When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord.

General information

■ Stickers in the sales package

The stickers contain important information for service and customer support purposes.

Attach the

sticker to your warranty card.

sticker to the Nokia Club Invitation Card supplied in the sales package.

■ Access codes

• Security code (5 digits): The security code protects your phone against unauthorised use, and is

supplied with the phone. The preset code is 12345. Change the code in the Settings menu, see

Security settings on page 68. Keep the new code secret and in a safe place separate from your

phone.

Set the phone to request the code, see Security settings on page 68.

• PIN code (4-8 digits): The PIN (Personal Identification Number) code protects your SIM card

against unauthorised use. The PIN code is usually supplied with the SIM card.

Set the phone to request the PIN code each time the phone is switched on, see Security settings on

page 68.

• PIN2 code (4-8 digits): The PIN2 code may be supplied with the SIM card and is required to access

some functions, such as charging unit counters.

• PUK and PUK2 codes (8 digits): The PUK (Personal Unblocking Key) code is required to change a

blocked PIN code. The PUK2 code is required to change a blocked PIN2 code.

If the codes are not supplied with the SIM card, contact your local service provider for the codes.

• Barring password: The barring password is needed when using the Call barring service, see Security

settings on page 68. The password is obtained from your service provider.

• Wallet code (4-10 digits): The wallet code is needed to access the wallet services. For further

information, see Wallet on page 85.

• Module PIN: The Module PIN is required to access the information in the Security module. The

module PIN is supplied with the SIM card if the SIM card has a security module in it.

• Signing PIN: The Signing PIN is needed for the digital signature. The signing PIN is supplied with

the SIM card if the SIM card has a security module in it.

■ Dynamic memory

Some features in your Nokia 6310i mobile phone use a common pool of memory (storage capacity)

called dynamic memory. When any of these features is used, there is less available memory for other

features which are also dependent on dynamic memory.

This is especially true with heavy use. For example, entering 250 calendar notes may use most of the

available dynamic memory. Consequently, if you attempt to download a Java application or save a

Wallet note, your phone may display a message saying Memory full. To proceed you would need to

delete some of the information or entries occupying the available dynamic memory.

The following functions share dynamic memory:

Calendar notes, To-do list, Java applications, WAP bookmarks, WAP cache and Wallet notes.

Overview of the functions of the phone

The Nokia 6310i mobile phone provides many functions which are very practical for daily use, such as

Clock, Alarm clock, Countdown timer, Games, Calculator, Calendar and To-do list.

■ Bluetooth

Bluetooth is a system that enables wireless connections between electronic devices at a range of

maximum 10 metres. There is no charge to connect devices via Bluetooth. A Bluetooth connection can

be used to send business cards and calendar notes. Use the phone as modem for fax and data or to

connect wirelessly to Bluetooth audio accessories.

In some countries, there may be restrictions on using Bluetooth devices. Check with your dealer and

the local authorities.

See also Bluetooth (Menu 11) on page 80.

■ GPRS (General Packet Radio Service)

GPRS is a technology that allows mobile phones to be used for sending and receiving data over the

mobile network. GPRS as such is a data bearer that enables wireless access to data networks such as

the Internet. The applications that use GPRS are WAP, SMS messaging and the GPRS dial-up (for

example, Internet and e-mail).

Before you can use GPRS technology

• You need to subscribe to the GPRS service.

For availability and subscription to the GPRS service, contact your network operator or service

provider.

• You need to save the GPRS settings for the applications used over GPRS.

See Setting up the phone for a WAP service on page 90.

See Message settings on page 57.

See GPRS modem settings on page 67 and Data and fax communication on page 104.

Pricing for GPRS and applications

Both the active GPRS connection and the applications used over GPRS, for example using WAP

services, sending and receiving data and SMS messages, require a fee. For more detailed information

on fees, contact your network operator or service provider.

■ HSCSD (High Speed Circuit Switched Data)

The phone enables you to use GSM high-speed data services. You can use high-speed functionality

when your phone is connected to a compatible computer via an IR connection, cable or Bluetooth, and

when the modem drivers supporting high-speed data software are installed on your computer and

selected as an active modem.

For availability and subscription to high-speed data services, please contact your network operator or

service provider.

See also Data and fax communication on page 104.

■ WAP (Wireless Application Protocol)

You can access various WAP services such as banking, news, weather reports and flight times. These

services are specially designed for mobile phones and they are maintained by WAP service providers.

Check the availability of WAP services, pricing and tariffs with your network operator and/or the

service provider whose service you wish to use. Service providers will also give you instructions on how

to use their services.

See WAP services (Menu 13) on page 89.

■ Java^TMapplications

Your phone supports Java^TMtechnology and includes some Java applications that have been

specifically designed for mobile phones. You can download additional applications up to 30kB each to

your phone from a PC with a Nokia Application Installer or from WAP services.

See Applications (Menu 6) on page 71.

For further download information please refer also to WAP services (Menu 13) on page 89.

■ Voice features

Your phone offers you the following voice features:

• Voice dialling - to make a call by using a voice tag, see Voice dialling on page 41.

• Voice commands - to activate certain functions in your phone that are listed in the Voice

commands menu, see Voice commands on page 84.

• Voice recorder - to make voice recordings, see Voice recorder on page 83.

■ E-Mails

You can use your phone to send and receive e-mail messages.

For availability and subscription to the e-mail service, please contact your network operator or service

provider.

See also Writing and sending e-mails on page 51.

1. Your phone

■ Keys and connectors

1.Power key,

Switches the phone on and off.

While in the phone book or in menu functions, or when the keypad is

locked, pressing the power key briefly turns the phone’s display lights

on for approximately 15 seconds.

2.Volume keys

The upper key increases and the lower key decreases the earpiece (and

headset) volume.

3.Selection keys,

and

The function of the keys depends on the guiding text shown on the

display above the keys, for example Menu and Names in standby

mode.

4.Scroll keys,

Enables scrolling through names, phone numbers, menus or settings.

5. dials a phone number, and answers a call. In standby mode it

and

shows the most recently called number.

ends an active call. Exits from any function.

enter numbers and characters. Pressing and holding

are used for various purposes in different functions.

calls your voice mailbox.

and

1 - Charger connector

2 - Headset and Data connector

3 - Infrared (IR) port

4 - Power key

■ Standby mode

When the phone is ready for use, and no characters have been entered by the

user, the phone is in standby mode.

Selection keys in standby mode are Menu and Names.

xxxx

Indicates the cellular network in which the phone is currently being used.

Shows the signal strength of the cellular network at your current location. The higher the bar,

the stronger the signal.

Shows the battery charge level. The higher the bar, the more power in the battery.

Other essential indicators in standby mode:

You have received one or several text or picture messages. See Reading and replying to a

message or an e-mail on page 53.

You have received one or several voice messages. See Voice messages on page 56.

The phone’s keypad is locked. See Keypad lock (Keyguard) on page 27.

The phone does not ring for an incoming call or a text message when Incoming call alert is set

to Off and Message alert tone is set to Off. See Tone settings on page 66.

The alarm clock is set to On. See Alarm clock on page 61.

The countdown timer is running. See Countdown timer on page 87.

All your calls are diverted to another number, Divert all voice calls. If you have two phone lines,

the divert indicator for the first line is

page 62.

and for the second line

. See Call divert on

Calls are limited to a closed user group (network service). See Security settings on page 68.

Bluetooth is on. See Bluetooth (Menu 11) on page 80.

2. Getting started

■ Installing the SIM card and the battery

Keep all miniature SIM cards out of the reach of small children.

• The SIM card and its contacts can easily be damaged by scratches or bending, so be careful when

handling, inserting or removing the card.

• Before installing the SIM card, always make sure that the phone is switched off and then remove

the battery.

1. With the back of the phone facing you, press the release button (1). Slide

the battery off the phone (2).

2. Slide the SIM card holder (3) as shown.

3. Insert the SIM card into the phone (4). Make sure that the SIM card is

inserted properly and that the golden contact area on the card is facing

downwards.

4. Slide the card holder over the SIM card to lock the card in its place (5).

5. Place the battery on the back of the phone (6) and slide it up the body

of the phone until it locks into place (7).

■ Charging the battery

1. Connect the lead of the charger to the socket on the bottom of

your phone.

2. Connect the charger to an AC wall socket.

The text Charging is displayed briefly if the phone is switched on.

If the battery is completely empty, it may take a few minutes

before the charging indicator appears on the display or any calls

can be made.

You can use the phone while the charger is connected.

The charging time depends on the charger and the battery used. For example, charging a BPS-2 battery

with the ACP-12 charger takes about 1 hours and 40 minutes.

■ Switching the phone on and off

Press and hold the power key,

Note that if the phone displays SIM card not supported even though the SIM card is

properly inserted, contact your network operator or service provider. Your phone does

not support 5 Volt SIM cards and the card may need to be changed.

• If the phone asks for a PIN code, key in the PIN code (displayed as ****), and press

OK.

See also PIN code request in Security settings on page 68 and Access codes on

page 14.

• If the phone asks for a security code, key in the security code (displayed as *****),

and press OK.

See also Speed dialling on page 41.

Making a conference call

Conference calling is a network service that allows up to six people to take part in a conference call.

1. Make a call to the first participant.

2. To make a call to a new participant, press Options and select New call.

3. Key in, or search the memory, for the phone number of the new participant and press Call. The first

call is put on hold.

4. When the new call has been answered, join the first participant in the conference call. Press

Options and select Conference.

5. To add a new participant to the call, repeat steps 2 through 4.

6. To have a private conversation with one of the participants:

Press Options and select Private. Scroll to the desired participant and press OK. Once you have

finished the private conversation, re-establish the conference call, as described in step 4.

7. To end the conference call, press

■ Answering or rejecting an incoming call

Press

to answer the incoming call and press

to end the call.

Press

to reject the incoming call.

If you press Silence, only the ringing tone is muted. Then either answer or reject the call.

Tip: If the Divert if busy function is activated to divert the calls, for example to your voice

mailbox, rejecting an incoming call will also divert the call. See Call divert on page 62.

Call waiting

You can answer an incoming call while you have a call in progress if you have activated the function

Call waiting service, see Call waiting service on page 63.

During a call, press

the active call.

to answer the waiting call. The first call is put on hold. Press

to end

■ Options during a call

Press Options during a call for some of the following network service options (if they are available

from your service provider and operator for the current call):

Mute or Unmute, End call, End all calls, Phone book, Menu and Hold or Unhold, New call, Conference,

Private, Answer and Reject.

Send DTMF is used to send DTMF tone strings, for example, passwords or bank account numbers. Key in

the DTMF string or search for it in the phone book and press OK. Note that you can key in the wait

character w and the pause character p by repeatedly pressing

Swap is used to switch between the active call and the call on hold, Transfer to connect a call on hold

to an active call, and disconnect yourself from the calls, and Record to start the voice recording.

4. Writing text

You can key in text in two different ways, using the traditional method, or another method called

predictive text input.

■ Using traditional text input

The indicator

text input.

is shown on the top left of the display when you are writing text using the traditional

• Press a number key,

to , repeatedly until the desired character appears. All the

characters available under a number key are not printed on the key. The available characters

depend on the language selected in the Language menu. See Language on page 64.

To insert a number, press and hold the number key you want.

• To switch between letter and number modes, press and hold

. Number mode is indicated by

123 at the top of the display.

• If the next letter you want is located on the same key as the present one, wait until the cursor

appears, or press or , and then key in the letter.

• If you make a mistake, press Clear to remove the character to the left of the cursor. Press and hold

Clear to delete the characters more quickly.

•

The most common punctuation marks and special characters are available under the number key

Pressing

brings up a list of special characters. Scroll through the list and press Use to select a

character.

To scroll through the list more quickly, press

select a character.

, and press

• To insert a space, press

• To switch between upper case and lower case, press

. The symbol ABC or abc shown at the top

of the display indicates the selected case.

• Press

to move the cursor to the right or left, respectively.

■ Using predictive text input

You can key in any letter with a single keypress. The predictive text input is based on a built-in

dictionary to which you can also add new words. When the dictionary becomes full, the new word

replaces the oldest added one. The indicator

writing text by using the predictive text input.

is shown on the top left of the display when you are

Setting predictive text input on or off

When writing text, press Options and select Dictionary.

• To set the predictive text input off, select Dictionary off.

• To set the predictive text input on, select a language available in the dictionary options list.

Predictive text input is only available for the languages in the list.

Tip: To quickly set the predictive text input on or off, press

twice when writing text.

Writing words with predictive text input

1. Start writing a word by using the keys

. Press each key only once for one letter. The

word changes after each keystroke.

For example, to write Nokia when the English dictionary is selected, press

for k, for i and for a:

for N,

for o,

In addition to the number keys, you can use other keys as follows:

• To delete a character to the left of the cursor, press Clear. Press and hold Clear to delete the

characters more quickly.

• To change the character case, press

press and hold

• To insert a symbol, press and hold

, and to change between letter and number mode,

, or alternatively, press Options and select Insert symbol.

Scroll to the symbol you want and press Use.

To scroll through the list more quickly, press

select a character.

, and press

• To insert a number while in letter mode, press and hold the respective number key, or press

Options, and select Insert number. Key in the numbers you want and press OK.

• To insert a name or a phone number by searching for it in the phone book, press Options and

select Insert name or Insert number.

• To insert a word, press Options and select Insert word. Write the word using the traditional text

input method and press Save. The word is also added to the dictionary.

2. When you have finished writing the word and it is correct, confirm it by pressing

space with

If the word is not correct, you have the following options:

or adding a

• Press

repeatedly until the desired word appears and confirm it.

• Press Options and select Matches.

If the ? character is displayed after the word, the word you intended to write is not in the dictionary.

To add the word to the dictionary, press Spell, key in the word (traditional text input is used) and

press Save. When the dictionary becomes full, the new word replaces the oldest one that was

added.

3. Start writing the next word.

Writing compound words

Key in the first part of the word and confirm it by pressing

. Write the last part of the compound

word and confirm it by pressing

5. Phone book (Names)

You can save names and phone numbers in the phone’s memory (internal phone book) or in the SIM

card’s memory (SIM phone book).

• The internal phone book can save up to 500 names with numbers and textual notes for each name.

The total amount of names that can be saved depends on the length of the names, numbers and

text items.

• The phone supports SIM cards that can save up to 250 names and phone numbers. Names and

numbers saved in the SIM card´s memory are indicated by

■ Selecting the phone book settings

1. Press Names and select Settings.

2. Select Memory in use, and select one of the following options:

Phone and SIM to recall names and numbers from both phone books. The names and numbers will

be saved in the phone’s memory.

Phone to use the phone’s internal phone book.

SIM card to use the SIM card’s phone book.

3. Select Phone book view and select one of the following options:

Name list to show three names at a time.

Name and no. to show one name and phone number at a time.

4. Select Memory status. Select Phone or SIM card to see how many names and phone numbers are

currently saved and how many can still be saved in the selected phone book.

■ Saving names and phone numbers (Add name)

Names and numbers will be saved in the memory being used, see Selecting the phone book settings

above.

1. Press Names and select Add name.

2. Key in the name and press OK. See Writing text on page 32.

3. Key in the phone number, and press OK. To key in the numbers, see Making a call on page 28.

4. When the name and number are saved, press Done.

Tip: Quick save

In standby mode, key in the phone number. Press Options, and select Save. Key in the name

and press OK.

Saving multiple numbers and text items per name

You can save up to five phone numbers and four brief text items in the phone’s internal phone book for

each name. Text items under one name can be street and e-mail addresses, a note and a web address.

The first number saved under a name is automatically set as the default number, and is indicated with

. When you select a name from the phone book, for example, to make a call, the default number is

used unless you select another number.

1. Make sure that the memory in use is either Phone or Phone and SIM. See Selecting the phone book

settings on page 36.

2. To access the list of names and phone numbers, press

in standby mode.

3. Scroll to the name saved in the phone’s internal phone book, to which you want to add a new

number or text item and press Details. (If the name is not saved in the phone, the phone will ask you

whether you want to save it there.)

4. Press Options and select Add number or Add detail.

5. Select one of the following number or text types:

General is the default type used when no other number type is set as the default number.

Other number types are

Mobile,

Home,

Office and

Fax.

Text types are E-mail ,

Web address ,

Postal addr. and

Note.

To change the number or text type, select Change type in the options list.

6. Key in the number or text item and press OK to save it.

7. Press Back and then Exit to return to standby mode.

Changing the default number

Press

in standby mode, scroll to the name you want and press Details. Scroll to the

number you want to set as the default. Press Options and select Set as default.

■ Searching for a name in the phone book

1. Press Names and select Search.

2. Either press List to access the phone book or key in the first character(s) of the name you are

searching for and press Search. The matches appear above a pop-up window.

3. Scroll to the name you want, and press Details. Scroll to view the details of the selected name.

Tip: To quickly find a name and phone number, press

in standby mode. Key

in the first letter(s) of the name, and/or scroll to the name you want.

■ Editing a name, number or a text item

Search for the name (and number) you want to edit and press Details. Scroll to the name, number or

text item you want to edit, and press Options. Select Edit name, Edit number, or Edit detail, and edit

the name, number or text and press OK.

■ Erasing names and numbers

Press Names and select Erase.

• To delete names and numbers one by one, select One by one and scroll to the name (and number)

you want to delete. Press Erase and press OK to confirm.

• To delete all names and numbers in the phone book at once, select Erase all and then scroll to the

phone book, Phone or SIM card and press Erase. Press OK and confirm with the security code.

■ Copying phone books

You can copy names and phone numbers from the phone’s memory to your SIM card’s memory and vice

versa.

1. Press Names and select Copy.

2. Select the copying direction, From phone to SIM card or From SIM card to phone.

3. Select One by one, All or Default nos..

Default nos. is shown if you copy from the phone to the SIM card. Only the default numbers will be

copied.

If you select One by one, scroll to the name you want to copy and press Copy.

4. To select whether you want to keep or erase the original names and numbers, choose Keep original

or Move original.

If you have selected All or Default nos., press OK when Start copying? or Moving is displayed.

■ Sending and receiving a business card

You can send and receive a person’s contact information as a business card either via IR, Bluetooth or

as a text message, if supported by the network.

• Receiving a business card

Make sure that your phone is ready to receive data through its IR port, see Infrared (Menu 10) on

page 79, or through Bluetooth (you must activate Bluetooth on your phone, see Activating and

deactivating Bluetooth on page 80). The user of the other phone can now send the name and phone

number via the same medium.

When you have received a business card via IR, Bluetooth or as a text message, press Show. Press

Options and select Save to save the business card in the phone’s memory, or Discard to discard the

received business card.

• Sending a business card

Using your phone’s infrared (IR) port or Bluetooth, you can send a person’s contact info as a

business card to a compatible phone or other handheld device which supports the vCard standard.

1. Search the phone book for the name and phone number you want to send, press Options and

select Send bus. card.

2. To send the business card via IR, make sure that the other phone or the PC is set up to receive

data via its IR port and select Via infrared.

To send the business card via Bluetooth, select Via Bluetooth. Bluetooth activates automatically

on your phone. For further information see Activating and deactivating Bluetooth.

To send the business card as a text message, select Via text msg..

■ Speed dialling

To make a call using the speed dialling keys, see Speed dialling a phone number on page 29.

Assigning a number to a speed dialling key

Press Names and select Speed dials. Scroll to the speed dialling key number you want, and press

Assign. If a number is already assigned to that key, press Options, and you can view, change or erase

the assigned number.

Press Search, and select first the name and then the number you want to assign.

■ Voice dialling

You can make a phone call by saying a voice tag that has been added to a phone number. You can add

up to ten voice tags. Any spoken word(s), such as a person’s name(s), can be a voice tag.

Before using voice dialling, note that:

•

Voice tags are not language dependent. They are dependent on the speaker's voice.

Voice tags are sensitive to background noise. Record them and make calls in a quiet environment.

When recording a voice tag or making a call by saying a voice tag, hold the phone in the normal position near to

your ear.

•

Very short names are not accepted. Use long names and avoid similar names for different numbers.

Note: You must say the name exactly as you said it when you recorded it. This may be difficult in, for

example, a noisy environment or during an emergency, so you should not rely solely upon voice dialling in

all circumstances.

Adding a voice tag

Save or copy in the phone’s memory the names and phone numbers to which you want to add a voice

tag.

You can also add voice tags to the names in the SIM card, but if you replace your SIM card with a new

one, you first need to delete the old voice tags before you can add new ones.

1. In standby mode, press

2. Scroll to the name to which you want to add a voice tag and press Details. Scroll to the phone

number you want and press Options.

3. Select Add voice tag.

4. Press Start, and clearly say the word(s) you want to record as a voice tag. After recording, the phone

plays the recorded tag.

5. When the voice tag has been successfully saved, Voice tag saved is displayed, a beep sounds and a

symbol

appears after the phone number with the voice tag.

Making a call by using a voice tag

When an application using the GPRS connection is sending or receiving data, you cannot make a call

using voice dialling. To make a call using a voice tag, end the application using the GPRS connection.

1. In standby mode, press and hold the volume down key, or press and hold Names. A short tone is

heard and Speak now is displayed.

2. Say the voice tag clearly.

3. The phone plays the recognised voice tag and then dials the phone number of the voice tag after 1.5

seconds.

If you are using the headset, press and hold the headset key to start the voice dialling.

Replaying, changing or erasing a voice tag

Press Names and select Voice tags. Scroll to the name with the voice tag you want, and press Options.

• To replay the voice tag, select Playback.

• To erase the voice tag, select Erase and press OK.

• To change the voice tag, select Change. Press Start to add the new voice tag.

■ My numbers

If supported by your SIM card your phone automatically stores the phone number of your SIM card.

Press Names and select My numbers to show the number.

■ Info numbers

You can call the information numbers of your service provider if the numbers are included on your SIM

card.

Press Names and select Info Numbers. Scroll in a category to a service number and press

to call

the number.

■ Service numbers

You can call the service numbers of your service provider if the service numbers are included on your

SIM card.

Press Names and select Service nos.. Scroll to a service number and press

to call the number.

■ Caller groups

You can arrange the names and phone numbers saved in the phone book into caller groups. For each

caller group, you can set the phone to sound a specific ringing tone and show a selected graphic on the

display when you receive a call from a phone number in the group, see below. To set the phone to ring

only upon calls from phone numbers belonging to a selected caller group, see Alert for in the section

Tone settings on page 66.

Press Names, select Caller groups and select the caller group you want. Select

•

Group name, key in a new name for the caller group and press OK.

Group ringing tone and scroll to the ringing tone you want to set for the group and press OK.

Default is the ringing tone selected for the currently active profile.

•

Group logo and select On to set the phone to display the group logo, Off not to display it, View to

view the logo, or Send logo to send the logo as a text message if supported by your network.

Group members. To add a name to the caller group, press OK at Add name. If you already have added

names and numbers to the group, press Options, scroll to Add name and press OK. Scroll to the

name you want to add to the group and press Add.

To remove a name from a caller group, scroll to the name you want to remove, and press Options.

Press OK at Remove name.

6. Using the menu

The phone offers you an extensive range of functions which are grouped in menus. Most of the menu

functions are provided with a brief help text. To view the help text, scroll to the menu function you

want and wait for 15 seconds. To exit the help text, press Back. See Help text activation on page 65.

■ Accessing a menu function

By scrolling

1. To access the menu, press Menu.

2. Scroll through the menu and select, for example, Settings by pressing Select.

3. If the menu contains submenus, select the one you want, for example Call settings.

4. If the selected submenu contains further submenus, repeat step 3. Select the next submenu, for

example Anykey answer.

5. Select the setting of your choice.

6. Press Back to return to the previous menu level, and Exit to exit the menu.

By shortcut

The menus, submenus and setting options are numbered and you can access them by using their

shortcut number. The shortcut number is shown in the top right corner of the display.

To access the menu, press Menu. Key in quickly, within two seconds, the index number of the menu

function you want to access.

For example, to set the Anykey answer On, press Menu,

and

■ List of menu functions

1. Messages

7. GPRS data counter

8. GPRS connection timer

1. Write message

2. Write e-mail

3. Inbox

3. Profiles

1. General

4. Outbox

2. Silent

5. Archive

3. Meeting

6. Templates

4. Outdoor

7. My folders

5. Pager

8. Erase messages

9. Voice messages

10.Info messages

11.Service command editor

12.Message settings

2. Call register

1. Missed calls

2. Received calls

3. Dialled numbers

4. Erase Recent Call Lists

5. Call duration

6. Call costs

4. Settings

1. Alarm clock

2. Time and date settings

3. Call settings

4. Phone settings

5. Tone settings

6. Accessory settings¹

7. GPRS modem settings

8. Security settings

9. Restore factory settings

5. Games

1. Only shown if one of the accessories has been connected to the phone.

6. Applications

7. Calculator

8. To-do list

9. Calendar

13.Services

1. Home

2. Bookmarks

3. Service inbox

4. Settings

5. Go to address

6. Clear the cache

14.SIM services¹

10.Infrared

11.Bluetooth

12.Extras

1. Voice recorder

2. Voice commands

3. Wallet

4. Countdown timer

5. Stopwatch

1. Only shown if supported by your SIM card. The name and contents vary depending on the SIM card.

7. Menu functions

■ Messages (Menu 1)

You can read, write and send text and picture messages or save your messages. All the

messages in your phone’s message memory are organised in folders.

Before you can send any text or picture messages, you need to save your message centre number, see

Message settings on page 57.

Writing and sending messages

Your phone is able to send and receive multi-part messages comprised of several ordinary text

messages (network service) each up to 160 characters. Invoicing is based on how many ordinary

messages are needed for a multi-part message.

The number of available characters and the current part number of a multi-part message are shown at

the top right of the display.

1. Press Menu, and select Messages and Write message

2. Key in a message. See Writing text on page 32.

See also Inserting a text template in a text message or in an e-mail on page 53 and Inserting a

picture template in a text message on page 53.

3. To send the message, press Options, and select Send.

4. Enter the recipient’s phone number and press OK to send the message, or search for the phone

number in the phone book. Press OK to send the message.

Note: When sending messages via the SMS network service, your phone may display the words "Message

Sent". This is an indication that the message has been sent by your phone to the message centre number

programmed into your phone. This is not an indication that the message has been received at the

intended destination. For more details about SMS services, check with your service provider.

Writing and sending e-mails

You can write and send e-mails of up to 160 characters. How to store an e-mail addresses in the phone

book see Saving multiple numbers and text items per name on page 37.

1. Press Menu, and select Messages and Write e-mail.

2. Enter e-mail address or search for an e-mail address in phone book. Press OK to accept.

3. Enter subject or leave entry field blank and press OK to accept.

4. Key in an e-mail. See Writing text on page 32.

See also Inserting a text template in a text message or in an e-mail on page 53.

Inserting a picture template is not possible.

5. To send the message, press Options, and select Send e-mail.

6. If requested enter the service number of the e-mail server, and press OK to send the e-mail.

You will always be asked for the service number of the e-mail server if you haven’t entered the

number in the message settings. See Message settings on page 57.

The service number of the e-mail server depends on your local network operator or service provider.

Note: When sending e-mails via the SMS network service, your phone may display the words "Message

Sent". This is an indication that the e-mail has been sent by your phone to the e-mail server. This is not an

indication that the e-mail has been received at the intended destination. For more details about e-mail

services, check with your service provider.

Options for sending a message

After you have written a message, press Options, and select Sending options.

• To send a message to several recipients, select Send to many. When you have sent the message to

everyone you want to send it to, press Done.

• To send a message using a message profile, select Sending profile and then the message profile you

want to use.

For example, if you select a profile you have defined as an e-mail transmission, key in or search the

phone book for the recipient’s e-mail address and press OK. Key in the e-mail service number, select

Accept to send the message.

To define a message profile, see Message settings on page 57.

• To forward a message to several recipients or using a message profile, select Forw. options and then

select Send to many or Sending profile.

Text and picture templates

Press Menu, select Messages and Templates. The list of text templates, indicated with

templates, indicated with , is displayed.

, and picture

Your phone offers you 10 picture message templates. You can also save new pictures into the

Templates folder. More pictures can be found on the Nokia website, http://www.club.nokia.com.

Note: This function can be used only if it is supported by your network operator or service provider. Only

phones that offer picture message features can receive and display picture messages.

• Each picture message is made up of several text messages. Therefore, sending one picture message

may cost more than sending one text message.

• Since picture messages are saved in the phone’s memory, you cannot view them if you use your SIM

card with another phone.

Inserting a text template in a text message or in an e-mail

When you are writing or replying to a message, press Options. Select Use template and select the

template you want to insert.

Inserting a picture template in a text message

When you are writing or replying to a text message, press Options. Select Attach picture and select a

picture to view. Press Attach to insert the picture into your message.

The

indicator on the header of the message indicates that a picture has been attached. The

number of characters that you can enter in a message, depends on the size of the picture.

To view the text and the picture together before sending the message press Options and select

Preview.

Reading and replying to a message or an e-mail

When you have received a text or picture message or an e-mail, the indicator

and the number of

new messages followed by messages received will appear on the display.

The blinking

indicates that the message memory is full. Before you can receive or send new

messages, delete some of your old messages.

1. Press Show to view the message, or press Exit to view it later.

Reading the message later: Press Menu, select Messages and Inbox.

2. If more than one message is received, select the message you want to read. An unread text message

is indicated by

in front of it and an unviewed picture message is indicated by

3. While reading or viewing the message, press Options.

You can select an option to erase, forward, edit, move, and rename the message you are reading.

Select Copy to calend. to copy the message to your phone’s calendar as a reminder note for the

current day.

Select Details to view, for example, the sender’s name and phone number, the message centre used,

reception date and time.

Select Use number to extract numbers from the current message.

Select Save picture to save the picture in the Templates folder.

Select Reply to reply to a message. Select Original text to include the original message in the reply,

or select standard answers, for example, Thank you or Congrats or Template to be included in the

reply, or select Empty screen.

4. In case of an e-mail confirm or edit e-mail address and subject.

5. Write your reply message.

6. Press Options, select Send, and press OK to send the message to the displayed number.

Multipart messages

Your phone can receive one long message (up to 459 characters) in sequences. You can start reading

the first part before the phone has received the entire message.

While viewing the message, you may see * some text missing * on the display. This is normal, and the

message content will be updated as soon as the missing sequence arrives.

If the memory is full, you may have to delete a message from your inbox or outbox before your phone

can update the missing text.

Inbox and outbox folders

After you have read an incoming text or picture message, the phone saves the message in the Inbox

folder of the Messages menu.

You can save a message that you want to send later in the Outbox or Archive folder.

Erasing the messages

Press Menu, select Messages and select Erase messages.

To delete all the messages in a folder, scroll to the folder and press OK. Then press OK when Erase all

read messages from folder? is displayed.

To delete all read messages from all the folders, scroll to All read and press OK. Then press OK when

Erase read messages from all folders? is displayed.

Archive folder and My folders

To organise your messages, you can move some of them to the Archive folder, or add new folders for

your messages.

While reading a message, press Options. Select Move, scroll to the folder where you want to move the

message and press OK.

To add or delete a folder, press Menu, select Messages and My folders.

• To add a folder, press Options and select Add folder.

• To delete a folder, scroll to the folder you want to delete, press Options and select Delete folder.

Voice messages

Voice mailbox is a network service and you may need to subscribe to it first. For more information and

for the voice mailbox number, contact your service provider.

Press Menu, select Messages and Voice messages. Select

•

Listen to voice messages to call your voice mailbox at the phone number you have saved within

Voice mailbox number menu.

Each phone line may have its own voice mailbox number, see Line for outgoing calls on page 64.

•

Voice mailbox number to key in or edit your voice mailbox number and press OK to save it.

If supported by the network, the indicator

your voice mailbox number.

will indicate new voice messages. Press Listen to call

Info messages

With the info message network service, you can receive messages on various topics, for example

weather or traffic conditions, from your service provider. For available topics and relevant topic

numbers, contact your service provider.

If the GPRS connection is set to Always online, the info messages may not be received. In that case, set

the GPRS connection to When needed, see Setting up the phone for a WAP service on page 90.

Service command editor

Press Menu, select Messages and Service command editor. Key in and send service requests, such as

activation commands for network services, to your service provider.

Message settings

Press Menu, select Messages, Message settings and Sending profile to define the settings for sending

messages.

If more than one message profile set is supported by your SIM card, select the set you want to change.

Select Message centre number to save the phone number of the message centre. You need the message

centre number to send text and picture messages. You receive the number from your service provider.

Select Messages sent as to select the message format, or Message validity. Select Default recipient

number (E-mail server in case of an e-mail message format) to save a default number to send messages

for this message profile, Delivery reports to request the network to send delivery reports on your

messages (network service), and Use GPRS to set GPRS as the preferred SMS bearer. Select Reply via

same centre to allow the recipient of your message to send you a reply via your message centre

(network service), and Rename sending profile to change the name of the selected message profile. The

message profile sets are displayed only if your SIM card supports more than one set.

Press Menu, select Messages, Message settings and Font size to change the font size of the message.

■ Call register (Menu 2)

The phone registers the phone numbers of missed, received and dialled calls, and the

approximate length and cost of your calls.

The phone registers missed and received calls only if the network supports these functions, the phone

is switched on and within the network’s service area.

When you press Options in the Missed calls, Received calls and Dialled numbers menus, you can view

the date and the time of the call, edit or erase the phone number from the list, save the number in the

phone book, or send a message to the number.

Missed calls and received calls

To view the list of the last ten phone numbers from which somebody has tried to call you (network

service), press Menu, select Call register and Missed calls.

Tip: When a note about missed calls is being displayed, press List to access the list of phone

numbers. Scroll to the number you would like to call back and press

To view the list of the last ten phone numbers from which you have most recently accepted calls

(network service), press Menu, select Call register and Received calls.

Dialled numbers

To view the list of the 20 phone numbers that you have most recently called or attempted to call, press

Menu, select Call register and Dialled numbers. See also Last number redialling on page 28.

Erase recent call lists

To erase the recent calls lists, press Menu, select Call register and select Erase recent call lists. Select

whether you want to delete all the phone numbers in the recent call lists, or only the numbers in the

missed calls, received calls or dialled numbers lists. You cannot undo the operation.

Call counters and call timers

Note: The actual invoice for calls and services from your service provider may vary, depending upon

network features, rounding-off for billing, taxes and so forth.

Press Menu and select Call register. Select

•

Call duration and scroll to view the approximate duration of your incoming and outgoing calls in

hours, minutes and seconds. To clear the timers, the security code is needed.

Each phone line has its own call timers and the timers of the selected line is displayed. See Line for

outgoing calls on page 64.

Call costs (network service) and select Last call units or All calls’ units to check the cost of your last

call or all calls.

Select Call cost settings and then select Clear counters, or select Show costs in to set the phone to

show the remaining talk time in terms of charging units Units, or units of currency, Currency.

Contact your service provider for charging unit prices. Select Call cost limit to limit the cost of your

calls to a certain amount of charging units or units of currency. The PIN2 code is needed for the call

cost settings.

Note: When no more charging units or currency units are left, calls may only be possible to the emergency

number programmed into your phone (e.g. 112 or other official emergency number).

•

GPRS data counter and scroll to check the amounts of data that were last sent and last received,

data sent and received in total, and to clear the counters. The counter unit is a byte.

GPRS connection timer and scroll to check the duration of the last GPRS connection or the total

GPRS connection. You can also clear the timers.

■ Profiles (Menu 3)

Your phone has various setting groups, or profiles, for which you can customise the

phone tones for different events and environments. At first, personalise the profiles to

your liking and then you only need to activate a profile to use it.

Available profiles are General, Silent, Meeting, Outdoor, and Pager.

Press Menu and select Profiles. Scroll to a profile and press Select.

• To activate the profile, select Activate.

Tip: To change the profile quickly in standby mode, press the power key

, scroll to the

profile you want to activate and press Select.

• To set the profile to be active for a certain amount of time up to 24 hours, select Timed and set the

time. When the time set for the profile expires, the previous profile that was not timed, becomes

active.

• To personalise the profile, select Personalise. Select the setting you want to change and make the

changes.

The current settings can also be changed in the Tone settings menu, see Tone settings on page 66. In

addition, you can rename a profile, Profile name. The General profile cannot be renamed.

■ Settings (Menu 4)

Alarm clock

The alarm clock uses the time format set for the clock. The alarm clock works even when the phone is

switched off.

Press Menu, select Settings and Alarm clock. Key in the alarm time and press OK. To change the time

when the alarm time is set, select On.

When the alarm time expires

The phone will sound an alert tone, and flash Alarm! and the alarm time on the display.

Press Stop to stop the alarm. If you let the phone continue to alarm for a minute or press Snooze, the

alarm stops for a few minutes and then resumes.

If the alarm time is reached while the phone is switched off, the phone switches itself on and starts sounding the

alarm tone. If you press Stop, the phone asks whether you want to activate the phone for calls. Press No to switch

off the phone or Yes to make and receive calls.

Note: Do not press Yes when wireless phone use is prohibited or when it may cause interference or danger.

Time and date settings

Clock settings

Press Menu, select Settings, Time and date settings and Clock.

Select Show clock (Hide clock) and the time is shown on the top right of the display when the phone is

in standby mode. Select Set the time, key in the correct time and press OK. Select Time format and set

the 12-hour or 24-hour time format.

The clock also serves the functions Messages, Call register, Alarm clock, timed Profiles and Calendar.

If the battery is removed from the phone for a long time, you may need to set the time again.

Date settings

Press Menu, select Settings, Time and date settings and Date. Select Set the date to give the current

date. Select Date format to choose how the date is displayed.

Auto update of date and time

Press Menu, select Settings, Time and date settings and Auto-update of date & time (network service).

To set the phone to automatically update the time and date according to the current time zone, select

On. To set the phone to ask for a confirmation before the update, select Confirm first.

Updating the date and time affects the alarm clock, calendar and voice recorder, and the alarm notes

you have set are now set to the local time. Updating may cause some calendar notes to expire.

Call settings

Call divert

Press Menu, select Settings, Call settings and Call divert (network service). With call divert you can

direct your incoming calls to another number, for example, to your voice mailbox number. For details,

contact your service provider. Divert options not supported by your SIM card or your network operator

may not be shown.

Select the divert option you want, for example, select Divert if busy to divert the voice calls when your

number is busy or when you reject an incoming call.

To set the divert setting on, select Activate, to set the divert setting off, select Cancel, or Check status

to check whether the divert is activated or not.

To change the delay of divert options Divert if not answered and Divert if not available, first select Set

delay and then select Activate to set the divert setting on.

To cancel all the active call diverts at once, select the option Cancel all diverts.

To see the divert indicators in standby mode, see Standby mode on page 21.

Anykey answer

Press Menu, select Settings, Call settings and then Anykey answer. Select On and you can answer an

incoming call by briefly pressing any key, except

and

Automatic redial

Press Menu, select Settings, Call settings and Automatic redial. Select On and your phone will make a

maximum of ten attempts to connect the call after an unsuccessful call attempt.

Speed dialling

Press Menu, select Settings, Call settings and Speed dialling. Select On and the names and phone

numbers assigned to the speed dialling keys, from

, can be dialled by pressing and

holding the corresponding number key.

Call waiting service

Press Menu, select Settings, Call settings and Call waiting service. Select Activate and the network will

notify you of an incoming call while you have a call in progress (network service). See Call waiting on

page 30.

Summary after call

Press Menu, select Settings, Call settings and Summary after call. Select On and the phone will briefly

display the duration and cost (network service) of the last call.

My number sending

Press Menu, select Settings, Call settings and My number sending. Select On and your phone number

will be displayed to the person you are calling (network service). Select Set by network to reset the

phone to the setting, On or Off, that you have agreed upon with your service provider.

Line for outgoing calls

Line for outgoing calls is a network service to select the phone line (that is, subscriber number) 1 or 2

for making calls. This menu is only shown if supported by your SIM card.

Press Menu, select Settings, Call settings and Line for outgoing calls. If you select Line 2 and have not

subscribed to this network service, you will not be able to make calls. However, calls on both lines can

be answered regardless of the selected line.

If supported by your SIM card, you can prevent the line selection by selecting the option Lock.

For more information on availability, contact your network operator or service provider.

Tip: In standby mode, you can switch from one line to the other by pressing and holding

Phone settings

Language

Press Menu, select Settings, Phone settings and Language. Select the language for the display texts. If

Automatic is selected, the phone selects the language according to the information on the SIM card.

Cell info display

Press Menu, select Settings, Phone settings and Cell info display. Select On to set the phone to indicate

when it is used in a cellular network based on Micro Cellular Network (MCN) technology.

If the GPRS connection is set Always online, the info messages may not be received. In that case, set

the GPRS connection to When needed, see Setting up the phone for a WAP service on page 90.

Welcome note

Press Menu, select Settings, Phone settings and Welcome note. Key in the note you would like to be

shown briefly when the phone is switched on. To save the note, press Options, and select Save.

Network selection

The cellular network to which your phone is connected can be selected either manually or

automatically.

Press Menu, select Settings, Phone settings and Network selection. Select Automatic and the phone

automatically selects one of the cellular networks available in your area.

If you select Manual, the phone shows a list of the available networks and you can select a network

that has a roaming agreement with your home network operator. Otherwise, No access will be

displayed and you must select another network. The phone stays in manual mode until the automatic

mode is selected or another SIM card is inserted into the phone.

Confirm SIM service actions

See SIM services (Menu 14) on page 103.

Help text activation

To set the phone to show or not to show the help texts, press Menu, select Settings, Phone settings and

Help text activation.

See also Using the menu on page 46.

Start-up tone

To set the phone to play or not to play a start-up tone when the phone is switched on, press Menu,

select Settings, Phone settings and Start-up tone.

If you have set a welcome note, the start-up tone will not be played, see Welcome note on page 65.

Tone settings

Press Menu, select Settings and then Tone settings. You can find the same settings in the Profiles

menu, see Profiles (Menu 3) on page 60.

Select Incoming call alert to choose how the phone notifies you of an incoming voice call. The options

are Ringing, Ascending, Ring once, Beep once and Off.

Select Ringing tone, Ringing volume and Vibrating alert for an incoming voice call and an incoming

message. The vibrating alert does not work when the phone is connected to a charger, desktop stand,

or a car kit.

Tip: You can save a maximum of ten ringing tones at a time in the ringing tone list that you

have received via IR or as a text message.

Select Message alert tone to set the alert tone for the incoming messages, Keypad tones, or

Warning tones to set the phone to sound tones, for example, when the battery is running out of power.

Select Alert for to set the phone to ring only upon calls from phone numbers that belong to a selected

caller group. Scroll to the caller group you want or All calls and press Mark.

Accessory settings

The accessory settings menu is shown only if the phone is or has been connected to one of the

accessories, e.g. headset HDC-9P or handsfree car kit CARK-91.

Press Menu, select Settings and Accessory settings. Select Headset, Handsfree or Loopset. When a

handsfree accessory is connected to the phone for the first time the active profile of the phone is used.

• Select Default profile to select the profile you want to be automatically activated when you

connect the selected accessory. You can select another profile while the accessory is connected.

• Select Automatic answer to set the phone to automatically answer an incoming call after five

seconds. If the Incoming call alert is set to Beep once or Off, automatic answer will not be in use.

• Select Lights to set the lights permanently on, On. Select Automatic to set the lights on for 15

seconds after a keypress. The Lights option is available only when Handsfree is selected.

• Select Use loopset to set the loopset in use instead of the headset,

Yes. Use loopset is available only when Loopset is selected.

GPRS modem settings

You can connect the phone via IR, Bluetooth or cable connection to a compatible PC and use the phone

as a modem to enable GPRS connectivity from the PC.

Press Menu, select Settings and GPRS modem settings. Select Active access point and activate the

access point you want to use. Select Edit active access point to change the access point settings.

• Scroll to Alias for access point and press Rename. Key in the name you would like for the activated

access point and press OK.

• Scroll to GPRS access point and press Edit. Key in the Access Point Name (APN) and press OK.

An Access Point Name is needed to establish a connection to the GPRS network. You can obtain the

Access Point Name from your network operator or service provider.

You can also set the GPRS modem service settings (Access Point Name) on your PC by using the Nokia

Modem Options software, see Modem setup on page 105. If you have set the settings on your PC and

your phone, note that the settings made on the PC will be used.

Security settings

Note: When security features, which restrict calls, are in use (call barring, closed user group and fixed

dialling), calls may be possible to certain emergency numbers in some networks (e.g. 112 or other official

emergency number).

Press Menu, select Settings and Security settings. Select

•

PIN code request to set the phone to ask for your PIN code every time the phone is switched on.

Some SIM cards do not allow the PIN code request to be turned off.

Call barring service (network service) to restrict incoming calls to and outgoing calls from your

phone. A barring password is required.

Fixed dialling to restrict your outgoing calls to selected phone numbers if this function is supported

by your SIM card. The PIN2 code is required.

Closed user group. Closed user group is a network service that specifies the group of people whom

you can call and who can call you. For more information contact your network operator or service

provider.

•

Security level. Select Phone and the phone will ask for the security code whenever a new SIM card is

inserted into the phone.

Select Memory and the phone will ask for the security code whenever you want to select the

phone’s internal memory or to copy from one memory to another. See Selecting the phone book

settings on page 36 and Copying phone books on page 39.

•

Change of access codes and you can change security code, PIN code, PIN2 code or barring password.

Codes can only include numbers from 0 through 9.

Note that you should avoid using access codes similar to the emergency numbers, such as 112, to

prevent accidental dialling of the emergency number.

Restore factory settings

To reset some of the menu settings to their original values, press Menu, select Settings and Restore

factory settings. Key in the security code and press OK. For example, the names and phone numbers

saved in the phone book are not deleted.

■ Games (Menu 5)

Note: The phone must be switched on to use this function. Do not switch on the phone

when the use of a wireless phone is prohibited or when it may cause interference or danger.

Starting a game

Press Menu, select Games and Select game. Select the game you would like to play, Snake II, Space

Impact, Bumper or select More games. If available for the game, select the game type or 1 player and

then New game.

You can get instructions about how to use the keys and how the game works by selecting Instructions

from the submenu.

More games may contain more Nokia Java games.

Starting a 2-player game

You may also play Snake II as a 2-player game via the IR port of your phone with a person who has the

same game on a compatible phone. Before starting a 2-player game, ensure that the IR ports of the

two phones are pointing at each other. See Infrared (Menu 10) on page 79.

To start the game, both players should select the option 2 players. Choose either Host game to start a

new 2-player game or Join game to join a game after the other player has chosen the Host game

option.

Game services and game settings

Press Menu, select Games and Game services or Settings. Select

•

Game services and the phone tries to connect to the WAP pages of Club Nokia by using the

currently active set of service settings.

If the connection fails, you may not be able to access Club Nokia from the WAP service whose

connection settings are currently active. In this case, enter the Services menu, activate another set

of service settings, see Making a connection to a WAP service on page 93. Try again to connect to

Club Nokia.

For the availability of different WAP services, pricing and tariffs, contact your network operator

and/or the WAP service provider.

•

Settings to set sounds, lights and vibrator, Shakes, for the game. The vibrator can be set on only if

Vibrating alert is activated, see Tone settings on page 66. You can save your Club Nokia

membership number, Club Nokia ID. For more information on Club Nokia and the game services,

visit www.club.nokia.com. Availability may vary by country.

■ Applications (Menu 6)

Note: The phone must be switched on to use this function. Do not switch on the phone

when the use of a wireless phone is prohibited or when it may cause interference or danger.

This menu allows the management of Java applications installed on your phone. Your phone software

includes some Java applications specially designed for this Nokia phone. Various service providers offer

other applications via WAP services. Before you can use one of these applications you have to

download it to your phone.

Launching an application

1. Press Menu, select Applications and Select app..

2. Scroll to an application (name depends on the application).

3. Press Options and select Open or press

If the selection is a single application it will launch.

Otherwise, a list of applications is displayed corresponding to the selected application set. Scroll to

desired application and press Select or

Tip: If an application uses the whole display area, no softkey names are displayed. Press one of

the selection keys or to show the options list. Then select one of the options or

. The application launches.

press Back to continue with the application.

Other options available for each application or application set:

•

Erase - to erase the application or application set from the phone.

•

Web access - to restrict the application for accessing the network. The allowed settings are Ask first

(asks first for network access), Allowed (network access allowed) and Not allowed (network access

not allowed).

•

Check version - to check if a new version of the application is available for download from the WAP

services.

Web page - to provide further information or additional data for the application from an Internet

page. This feature needs to be supported by the network. It is only shown if an Internet address has

been provided with the application.

•

Details - to give additional information about the application.

Downloading an application

You can download new Java applications in different ways:

• Press Menu, select Applications and Open browser to find an appropriate Java application. See also

Browsing the pages of a WAP service on page 94.

• Use the game download functionality, see Game services and game settings on page 71.

• Use the Internet to download Java applications to your PC. Use the Application Installer from PC

Suite to transfer the applications from your PC to your phone.

Note: If you choose to download (Java) applications from a non-Nokia site, you should take the same

precautions, for security or content, as you would with any site.

Following texts may appear during a download or during an operation of a Java application:

•

Action failed , too many applications in the phone. Erase any unwanted application and download

again.

•

Application error , an error occurs in the running application.

Application not supported , the application is incompatible with the phone.

Call in progress , the application tries to establish a web connection while the phone is already in

call.

•

File format not recognised , either the application is invalid or the transfer from PC has not finished.

File too large , a file is too large to run on the phone or the gateway does not support large files.

Invalid file , the application is invalid.

Launch failed , the phone couldn't start the application. Please try again.

•

Unable to open application , there is insufficient resource to run the application. End any active

calls or features and try to open the application again.

Unknown (appearing in the Application's list), the application has no name.

Showing system information

View the size of memory available for application installations.

Press Menu, select Applications and Memory.

Your phone has 128 kB of memory to store Java applications, and up to 50 kb more may be available

from the phone's dynamic memory. For more information see Dynamic memory on page 15.

■ Calculator (Menu 7)

The calculator in your phone adds, subtracts, multiplies, divides, calculates the square

and the square root and converts currency values.

Note: The phone must be switched on to use this function. Do not switch on the phone when the use of a

wireless phone is prohibited or when it may cause interference or danger.

This calculator has a limited accuracy and rounding errors may occur, especially in long divisions.

1. Press Menu and select Calculator.

2. When ’0’ is displayed on the screen, key in the first number in the calculation, press

for a

decimal point.

3. Press Options and select Add, Subtract, Multiply, Divide, Square, Square root or Change sign.

Tip: Alternatively, press

once to add, twice to subtract, three times to multiply or

four times to divide.

4. Key in the second number.

5. For a total, press Options and select Equals. Repeat steps 3 through 5 as many times as necessary.

6. To start a new calculation, first press and hold Clear.

Making a currency conversion

1. Press Menu and select Calculator.

2. To save the exchange rate, press Options and select Exchange rate. Select either of the displayed

options. Key in the exchange rate, press

for a decimal point, and press OK. The exchange rate

remains in the memory until you replace it with another one.

3. To make the currency conversion, key in the amount to be converted, press Options and select In

domestic or In foreign.

You can also make the currency conversion in standby mode. Key in the amount to be converted, press

Options and select In domestic or In foreign.

■ To-do list (Menu 8)

You can save a note for a task you have to do. The notes can be saved in priority order.

You may be able to save up to 30 notes, but this depends on how long the notes are. This

feature utilises the dynamic memory. For more information see Dynamic memory on page 15.

Note: The phone must be switched on to use this function. Do not switch on the phone when the use of a

wireless phone is prohibited or when it may cause interference or danger.

Press Menu and select To-do list. Press Options, or scroll to the note you want and then press Options.

Select

•

Add to add a new note. Key in the subject for the note, press Options and select Save. Select the

priority for the note, High (1), Medium (2), or Low (3). The notes are listed first in priority order and

then in alphabetical order.

Dictionary, refer to Setting predictive text input on or off on page 33.

•

Erase to delete the selected note.

Edit to modify the contents of the note.

Edit priority to change the priority level for the note.

View to view the selected note.

Go to priority to select the priority level from which you would like to view notes.

Save to calend. to save the note as a calendar note.

Send as text to send the note to another phone as a text message.

■ Calendar (Menu 9)

The calendar helps you to keep track of reminders, calls that you need to make,

meetings, and birthdays. Your phone supports up to 250 calendar notes. This feature

utilises the dynamic memory. For more information see Dynamic memory on page 15.

Note: The phone must be switched on to use this function. Do not switch on the phone when the use of a

wireless phone is prohibited or when it may cause interference or danger.

Press Menu and select Calendar. Scroll to the day you want. If there are any notes set for the day, the

corresponding note type indicator is shown. If you want to see the day’s notes, press Options and

select Day notes. The note indicator is shown on the first line. You can view a single note by scrolling to

it in day view, then pressing Options and View. The week view shows four weeks at a time.

The other options for the calendar views include:

• Options for making a note, for sending a note via IR or via Bluetooth, or as a note directly to another

phone’s calendar or as a text message.

• Options for erasing, editing, moving or repeating a note.

•

Settings to set, for example, the date, time, date format or time format. In the Auto-erase option,

you can set the phone to delete old notes automatically after a specified time. However, the repeat

notes, for example, birthday notes, will not be deleted.

Making a calendar note

For keying in letters and numbers, see Writing text on page 32.

Press Menu and select Calendar. Scroll to the date you want, press Options and select Make a note.

Select one of the following note types:

•

Meeting - Key in the note, or search for the name in the phone book, and press OK. Then key in

the time for the meeting and press OK. If you like, select Alarm on and then the alarm time for the

note.

Call - Key in the phone number you want, press OK, and key in the name and press OK, or

search for them in the phone book. Then key in the time for the call and press OK. If you like, select

Alarm on and then the alarm time for the note.

Birthday - Key in the person’s name (or search for it in the phone book), and press OK. Then key

in the date of birth, and press OK. Key in the year of birth (optional), and press OK. If you key in the

year, the note shows you the person’s age after the name. If you like, select Alarm on and then the

alarm time for the note.

•

Memo - Key in the note and press OK.

When a tone alert is set, the indicator

is displayed when you view the notes.

When the phone alarms for a note

The phone beeps, and displays the note. With a call note

number by pressing . To stop the alarm and view the note, press View. To stop the alarm without

viewing the note, press Exit.

on the display, you can call the displayed

■ Infrared (Menu 10)

You can set up the phone to receive data through its infrared (IR) port. To use an IR

connection, the device with which you want to establish a connection must be IrDA

compliant. You can send or receive data such as business cards and calendar notes to or from a

compatible phone or data device (for example, a computer) via the IR port of your phone.

Do not point the IR (infrared) beam at anyone’s eye or allow it to interfere with other IR devices. This

device is a Class 1 Laser product.

Note: The phone must be switched on to use this function. Do not switch on the phone when the use of a

wireless phone is prohibited or when it may cause interference or danger.

Sending and receiving data via IR

• Ensure that the IR ports of the sending and receiving devices are pointing at each other and that

there are no obstructions between the devices. The preferable distance between the two devices in

an infrared connection is one metre at most.

• To activate the IR port of your phone to receive data via IR, press Menu and select Infrared.

• The user of the sending phone selects the desired IR function to start data transfer.

If data transfer is not started within two minutes after the activation of the IR port, the connection is

cancelled and has to be started again.

IR connection indicator

• When

is shown continuously, the IR connection is activated and your phone is ready to send or

receive data via its IR port.

• When

blinks, your phone is trying to connect to the other device or a connection has been lost.

■ Bluetooth (Menu 11)

You can set up the phone to send and receive data through Bluetooth. In the Bluetooth

menu, you can manage connections and define settings.

Since Bluetooth devices communicate using radio waves, your phone and the other Bluetooth device

do not need to be in line of sight. The two devices only need to be within a maximum of 10 meters of

each other, although the connection can be subject to interference from obstructions such as walls or

other electronic devices.

Note: The phone must be switched on to use this function. Do not switch on the phone when the use of a

wireless phone is prohibited or when it may cause interference or danger.

In some countries, there may be restrictions on using Bluetooth devices. Check with your dealer and the

local authorities.

Activating and deactivating Bluetooth

Press Menu and select Bluetooth. When Bluetooth is displayed, select On or Off. The phone displays a

notification that Bluetooth is activated or deactivated. When Bluetooth is on, the indicator

displayed.

Using Bluetooth consumes the battery and the phone’s operating time will be reduced. Be careful not to let it run in

the background when performing other operations with your phone.

Bluetooth device name

When activating Bluetooth for the first time, the name of your phone Nokia 6310i is shown. You can

accept the default name or change it. The name can be up to 15 characters. After the name is accepted,

Name saved is shown. Bluetooth device names help you to distinguish one Bluetooth device or

accessory from another.

Note that the name of your phone does not appear after you have already changed the name in

Bluetooth settings before the first activation of Bluetooth. See Bluetooth settings on page 82.

Pairing with Bluetooth Passcode

To create a secure connection, you may need to exchange Bluetooth Passcodes with the device you are

connecting to for the first time. This operation is called pairing. The Bluetooth Passcode is a 1 to 16

character-long numeric code. Accessories, as well as data and fax connections to a compatible

computer, require a pairing. Nokia accessories have fixed passcodes that are supplied with the

accessory.

When forming a Bluetooth connection to devices other than a Nokia accessory, for example a PDA, you

can use a temporary passcode created by yourself. This passcode is used only once and you do not have

to memorise it. Make up identical passcodes with the other device with which you want to share a

Bluetooth connection. If you need to create the pairing between the two devices again, you can make

up a new code.

Bluetooth connection

Press Menu, select Bluetooth and Search for audio accessories. The phone starts searching for audio-

enabled devices and accessories. Devices responding to the inquiry appear on a list of Bluetooth

accessories one by one starting from the device found first. The phone shows the device found last on

the bottom of the list. To end the inquiry, press Stop.

If you want to make a Bluetooth connection with non-audio accessory use the other device to

establish the connection.

Scroll to the device you want and press Select. When the connection has been established, the device

shows Connected to followed by the device’s name.

If devices have not been paired, the user is asked to enter the passcode of the desired device. See

Pairing with Bluetooth Passcode above.

Note that if the device in the list moves out of range and you try to connect to it, an error note is

shown.

Note that you can have only one active connection at a time.

To view the currently active device, press Menu, select Bluetooth and View active device. From here,

you can also close the connection to the device.

To view the list of paired devices, press Menu, select Bluetooth and View paired devices. The oldest

pairing is on the top of the list. When you press Options under View paired devices, some of the

following options may be available, depending on the status of the device or connection: Assign short

name, to give a name (visible to you only) to the paired device, Delete pairing to remove the selected

device from the list, Request conn. authorisation to define whether the connection from the paired

device is established automatically (No) or if the phone asks permission before connecting (Yes).

Bluetooth settings

The settings are for changing the phone’s own Bluetooth-related settings. Press Menu, select

Bluetooth and Bluetooth settings. You have the following options:

•

My phone’s visibility to change the way the phone is visible to other Bluetooth devices. The options

are as follows:

•

Shown to all, which is the default mode.

Hidden to make the device non-discoverable, responding only to devices that it has been paired

with.

•

My phone’s name to change your phone’s Bluetooth device name, which is shown to others.

■ Extras (Menu 12)

Note: The phone must be switched on to use each of the functions in this menu. Do not

switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.

Voice recorder

You can record pieces of speech, sound or an active call. For example, this is useful when recording a

name and phone number for writing them down later.

Note: Obey all local laws governing recording of calls. Do not use this feature illegally.

Recording

1. Press Menu, select Extras and Voice recorder.

2. To start the recording, select Record. To start the recording during a call, press Options, and select

Record.

When recording, hold the phone in the normal position near to your ear.

3. To end the recording, press Stop.

4. Key in a new name for the recording and press OK to save it.

If you do not want to save the recording, press Clear to erase the preset name. Then press Back and

OK.

If you record an active call, the phone automatically saves the recording by the name Recording.

List of recordings

Press Menu, select Extras and Voice recorder. Select Recordings list, scroll to the recording you want

and press Options.

• Select Playback to listen to the selected recording.

• Select Edit title. Key in a new name for the recording and press OK.

• Select Erase to erase the recording. Press OK to confirm.

• Select Add alarm. Key in the date for the alarm and press OK. Key in the time for the alarm and press

OK.

Alarm replaces Add alarm when the alarm is set on. Select Alarm and the name of the recording,

and the date and the time for the alarm are displayed. To remove the alarm, press Erase and then

press OK.

When the alarm time expires, the phone will sound an alert tone, Recording!, and the alarm time and

the name of the recording are displayed. Press Stop to stop the alarm, and then press Play to play the

recording.

Voice commands

You have a list of phone functions which can be activated by saying a voice tag. Up to five voice tags

for the voice commands can be added.

Press Menu, select Extras and Voice commands. Select the command folder you want, scroll to the

command to which you want to add a voice tag and press Options. If the command already has a voice

tag, the indicator

is shown.

You can add a voice command in the same way as described in Adding a voice tag on page 42. See also

Replaying, changing or erasing a voice tag on page 43.

You can activate the voice command in the same way as making a call by using a voice tag, see

page 43.

When an application using the GPRS connection is sending or receiving data, you cannot activate a

voice command. To activate a voice command, end the application using the GPRS connection (WAP,

Dial-up).

Wallet

In Wallet you can store personal information, such as notes and virtual cards (for example credit or

loyalty card information). You can also enter a WAP store and pay for your purchases with the wallet.

When you try to access wallet for the first time, you need to create your own wallet code at the prompt

Create wallet code:. Key in and accept the wallet code, which can be 4-10 characters long and confirm

it at the prompt Verify wallet code: If the verification succeeds, the phone displays Wallet code created.

Note that there is no limit to the number of times you can key in the code verification. If you key in a

wrong wallet code several times, the wallet application is blocked for five minutes.

If you want to reset the content of the wallet and the wallet code, key in *#3925538# in idle mode.

You need to enter the phone’s security code before the contents and the wallet code are erased. See

also Access codes on page 14. Note that all the wallet contents will be erased.

Press Menu, select Extras, and Wallet. The phone displays Enter wallet code: After you have keyed in

the correct code and confirmed it, you can select Cards, Personal notes or Settings.

Storing personal card information

Press Menu, select Extras, Wallet and Cards to view the list of cards. The maximum amount of cards is

five. To view or edit card details, select one of the cards and press Select for some of the following

options:

•

Card info to keep track of, for example, card name, type, number and expiry date.

User info to store user name and password.

Shipping info to store your delivery information, for example your name and address.

Billing info to store credit card information about cards where billing goes to a different address

than your own, for example company credit cards.

•

Receipt info to store receipt delivery information, for example phone numbers and e-mail

addresses.

•

Copy card to make a copy of an existing card in the wallet.

Clear card to clear card details information fields.

Rename card to rename the selected card.

Personal notes

In personal notes you can store a maximum of 30 sensitive personal notes, for example, passcodes or

notations. This feature utilises the dynamic memory. For more information see Dynamic memory on

page 15.

Press Menu, select Extras, Wallet and Personal notes. By pressing Options you can view notes, add new

notes, edit a selected note and sort notes either by name or by date. Send as text copies the content of

the note to a text message. Copy to calend. copies the title and the note to the calendar as a reminder.

With Use number you can pick one or more numbers from a note.

Wallet settings

Press Menu, select Extras, Wallet and Settings. Select

•

Code request to switch the Wallet Code Request on or off. Note that you need to key in the existing

Wallet Code before you can switch the code request on or off.

•

Change code to change the wallet code.

Paying your purchases with wallet

You can access a WAP store and pay your purchases with the wallet using the following procedure:

1. Establish a WAP connection, see below.

2. Enter the WAP store you want, and choose the product you want to buy.

3. Fill in the payment data form you receive from the service provider by transferring the information

from the wallet, i.e. press Option and select Use wallet info to find the card with the information

you need and select it. If you want to fill in all the fields, choose Fill in all fields (this is shown only

when the WAP page or the card supports the Electronic Commerce Modeling Language standard).

You can also choose only one information field from a card. The phone displays the filled form.

4. Approve the purchase, and then the information is forwarded.

5. You may receive a sign-in document from the WAP service that you need to sign to make the

purchase binding, see Digital signature on page 101.

Countdown timer

Press Menu, select Extras and Countdown timer. Key in the alarm time in hours and minutes and press

OK to start the countdown timer. If you like, write your own note text which is displayed when the

time expires, and press OK. When the timer is running, the indicator

is shown in standby mode.

If the alarm time is reached when the phone is in standby mode, the phone sounds a tone and flashes

the note text if it is set or else Countdown time up. Stop the alarm by pressing any key. If no key is

pressed, the alarm stops automatically within 30 seconds. Press OK to erase the note text.

To stop the countdown timer or to change the countdown time:

Press Menu, select Extras and Countdown timer. Select Change time to set the timer again, or Stop

timer to stop the timer.

Stopwatch

You can measure time, take intermediate times or lap times by using the stopwatch. During timing, the

other functions of the phone can be used.

Using the stopwatch consumes the battery and the phone’s operating time will be reduced. Be careful not to let it

run in the background when performing other operations with your phone.

Time observation and time splitting

1. Press Menu, select Extras, Stopwatch and Split timing.

You can select Continue if the timing was set in the background, for example, because of an

incoming call.

2. Press Start to start the time observation. Press Split every time you want to take an intermediate

time. The intermediate times are listed below the running time on the display. Scroll to view the

times.

3. Press Stop to stop the time observation.

4. Press Options and select

Start to start the time observation again. The new time is added to the previous time.

Save to save the time. Key in a name for the measured time and press OK. If no name is keyed in, the

total time is used as a title.

Reset to reset the time without saving it.

Lap times

Press Menu, select Extras, Stopwatch and Lap timing. Press Start to start the time observation and Lap

to take a lap time. Press Stop to stop the lap timing. Press Options and you can save or reset the lap

times. Refer to Time observation and time splitting above.

Viewing and erasing times

Press Menu, select Extras, and Stopwatch.

If the stopwatch is not reset, you can select Show last to view the latest measured time. Select View

times. and a list of names or final times of the time sets is shown, select the time set you want to view.

To delete the saved times, press Options and select Erase times. Select All at once and press OK, or

select One by one and scroll to the times you want to delete. Press Erase and press OK.

■ WAP services (Menu 13)

See also WAP (Wireless Application Protocol) on page 18.

Note: The phone must be switched on to use this function. Do not switch on the phone

when the use of a wireless phone is prohibited or when it may cause interference or danger.

The WAP services use Wireless Mark-Up Language (WML) on their WAP pages. Web pages using the

Hyper Text Mark-Up Language (HTML) cannot be viewed on your phone.

Basic steps for accessing and using WAP services

1. Save the service settings that are needed to access the WAP service that you want to use. See

Setting up the phone for a WAP service below and Appearance settings of the WAP browser on

page 96.

2. Make a connection to the given WAP service . See Making a connection to a WAP service on

page 93.

3. Start browsing the pages of the WAP service. See Browsing the pages of a WAP service on page 94.

4. Once you are done with browsing, end the connection to the WAP service. See Ending a WAP

connection on page 96.

Setting up the phone for a WAP service

You may receive the service settings as a text message from the network operator or service provider

that offers the WAP service that you want to use. For more information, contact your network operator

or service provider, or visit Club Nokia’s Web site (www.club.nokia.com).

You can also key in the settings manually. For appropriate settings, contact your network operator or

service provider. The WAP settings may be available, for example, on the Web site of the network

operator or service provider.

Saving the service settings received as a text message

When you receive the service settings as a text message, Service settings received is displayed.

• To save and activate the received settings, press Options and select Save.

If no settings are saved in Active service settings, the settings are saved under the first available

connection set and activated.

• To discard the received settings, press Options and select Discard.

• To view the received settings first, press Options and select View. To save the settings, press Save.

Keying in the service settings manually

1. Press Menu, select Services, and Settings.

2. Select Active service settings.

You need to activate the set where you want to save the service settings. A set is a collection of

settings needed for making a connection to a WAP service.

3. Scroll to the set you would like to activate and press Activate.

4. Select Edit active service settings.

Select each of the service settings one by one and key in all the required settings.

•

Settings’ name - Key in the new name for the settings set and press OK.

Homepage - Key in the homepage address of the WAP service that you want to use and press

OK.

•

Session mode - Select Permanent or Temporary.

Connection security - Select On or Off.

When the connection security is On, the phone tries to use a secure connection with the WAP

service. If a secure connection is not available, the connection will not be made. If you wish to

connect anyway, with a non-secure connection, you must set the connection security to Off.

•

Data bearer - Select GSM data or GPRS. For pricing, connection speed and other information,

contact your network operator or service provider.

The following options depend on the selected data bearer:

When GSM data is the selected data bearer:

•

Dial-up number - Key in the phone number and press OK.

IP address - Key in the address and press OK. You obtain the IP address from your network

operator or service provider.

•

Authentication type - Select Secure or Normal.

Data call type - Select Analogue or ISDN.

Data call speed - Select the speed you want to use, or select Automatic. Automatic is available

only if the current selected data call type is Analogue. The actual data call speed depends on the

service provider.

•

name and password keyed in the following settings. If you select Manual, the login information

is required when establishing a connection.

•

User name - Key in the user name and press OK.

Password - Key in the password and press OK.

When GPRS is the selected data bearer:

•

GPRS connection - Select Always online or When needed.

If you select Always online, the phone is automatically registered to a GPRS network when you

switch on the phone. Starting a WAP or PC dial-up application creates the connection between

phone and network and data transfer is possible. When you end the application, GPRS

connection is ended but the registration to the GPRS network remains.

If you select When needed, the GPRS connection is established when you connect to a WAP

service and closed when you end the WAP connection.

•

GPRS access point - Key in the access point name and press OK.

An access point name is needed to establish a connection to a GPRS network. You obtain the

access point name from your network operator or service provider.

IP address - Key in the address and press OK. You obtain the IP address from your network

operator or service provider.

•

Authentication type - Select Secure or Normal.

to Always online, the Always online connection will be disabled.

•

User name - Key in the user name and press OK.

Password - Key in the password and press OK.

Making a connection to a WAP service

First, make sure that the service settings of the WAP service you want to use are activated. To activate

the settings:

• Press Menu, select Services and Settings. Select Active service settings and scroll to the set you

want to activate and press Activate.

Secondly, make a connection to the WAP service. There are three ways to connect:

• Open the homepage of the WAP service:

Press Menu, select Services and Home.

Tip: To quickly open the homepage of a WAP service:

In standby mode, press and hold

• Select a bookmark of the WAP service:

Press Menu, select Services, Bookmarks, and select a bookmark.

If the bookmark does not work with the current active service settings, activate another set of

service settings and try again.

• Key in the address of the WAP service:

Press Menu, select Services and then Go to address. Key in the address of the WAP service, press

for special characters, and press OK.

Note that it is not necessary to add the prefix http:// in front of the address since it will be added

automatically.

Browsing the pages of a WAP service

After you have made a connection to the WAP service, you can start browsing its WAP pages. The

function of the phone keys may vary in different WAP services. Follow the text guides on the phone

display. For more information, contact your WAP service provider.

Note that if GPRS is selected as the data bearer, the indicator is shown on the top left of the display

during browsing. If there is an incoming (or outgoing) call during a GPRS connection, the indicator

will be shown on the top right of the display. The GPRS connection is suspended.

General guidelines for using the phone keys

• Use the scroll keys

to browse the WAP page.

• To select a highlighted item, press

• To enter letters and numbers, press the keys

key

and to enter special characters, press the

• Some or all of the following options are available while a WAP connection is in progress. Press

Options and select the option you want.

Home - to go back to the homepage of the WAP service

Bookmarks - the list of bookmarks is displayed. For details, see Bookmarks on page 97.

Edit / Open row / Open link / Open list - to key in text or select a highlighted item on the WAP page.

Add bookmark - to add the current WAP page as a bookmark in your bookmarks list.

Go to address - to key in the address of the WAP service you want.

Service inbox - the list of service messages is displayed, see Service inbox on page 99.

Appear. sett. - for details, see Appearance settings of the WAP browser on page 96.

Cookie settings - for details, see Download settings on page 97.

Use number - to copy a number from the current WAP page for saving or calling (and ends the WAP

connection). If the WAP page contains several numbers, you may select the desired one.

Reload - to reload and update the current WAP page.

Clear the cache - for details, see The cache memory on page 100.

Security info - to view security information about the current WAP connection and the server.

Quit - to quit browsing and end the call.

WAP direct calling

Certain WAP pages support functions that you can access while browsing. This is indicated on the WAP

page. You can., for example, be able to

• make a voice call while you are on a WAP page.

• send DTMF tones while a voice call is in progress.

• save in the phone book a name and a phone number from a WAP page.

The phone asks for a confirmation before carrying out the function.

Ending a WAP connection

When you are using a WAP service, press Options and select Quit. When Quit browsing? is shown, press

Yes.

Alternatively, press

. If GSM data is the selected data bearer, press

twice.

The phone ends the call and terminates the connection to the WAP service.

Appearance settings of the WAP browser

1. When no WAP connection is in progress:

Press Menu, select Services, Settings and Appearance settings.

When a WAP connection is in progress:

Press Options and select Appear. sett..

2. Select Text wrapping or Show images.

3. Select On or Off for Text wrapping and Yes or No for Show images.

When Text wrapping is set to On, the text continues on to the next line if it cannot be shown on one

line.

When Show images is set to No, any pictures appearing on the WAP page are not shown. This can

speed up the browsing of WAP pages that contain a lot of pictures.

Download settings

You can set the phone to allow or prevent the receiving of cookies.

A cookie is data that a WAP site saves in your phone’s browser cache memory. The data can be, for

example, your user information or your browsing preferences. Cookies will be saved until you clear the

cache memory, see The cache memory on page 100.

1. When no WAP connection is in progress:

Press Menu, select Services, Settings and Cookie settings.

When a WAP connection is in progress:

Press Options and select Cookie settings.

2. Select Cookies and select Allow or Reject to allow or prevent the phone to receive cookies.

Bookmarks

You can save up to 25 WAP page addresses as bookmarks in the phone’s memory. This feature utilises

the dynamic memory. For more information see Dynamic memory on page 15.

1. When no WAP connection is in progress:

Press Menu, select Services and then Bookmarks.

When a WAP connection is in progress:

Press Options and select Bookmarks.

2. Scroll to the bookmark you want to use and press Options.

3. Select one of the following options:

•

Go to to make a connection to the WAP page associated with the bookmark.

Edit or Erase to modify or delete the selected bookmark.

Send to send the selected bookmark to another phone via SMS, As bookmark.

New bookmark to create a new bookmark without connection to a WAP service. Key in the

address and the title of the WAP page and press OK.

Note that your phone may have some pre-installed bookmarks for sites not affiliated with Nokia. Nokia

does not warrant or endorse these sites. If you choose to access them, you should take the same

precautions, for security or content, as you would with any site.

Receiving a bookmark

When you have received a bookmark as a text message, press Options and select View to view the

bookmark, Save to save the bookmark, or Discard to discard it.

Service inbox

The phone is able to receive service messages (pushed messages) sent by your service provider. Service

messages are notifications of, for example, news headlines, and they may contain a text message or

the address of a WAP service.

1. To access the service inbox when no WAP connection is in progress:

When you have received a service message, 1 service message received will be displayed. Press View

to access the Service inbox.

If you press Exit the message is moved to the Service inbox. To access the Service inbox later, press

Menu, select Services, and the Service inbox.

When a WAP connection is in progress:

Press Options and select Service inbox.

2. Scroll to the message you want and press Options.

Select Retrieve to activate the WML browser and download the indicated content.

Select Details to display detailed information on the service notification.

Select Erase to delete the selected service notification.

To set the phone to receive service messages

Press Menu, select Services, Settings, Service inbox settings, and Service messages. To set the phone to

receive service messages, select On. If you select Off, the phone will not receive service messages.

The cache memory

Note: The information or services you have accessed are stored in the cache of your phone. A cache is a

buffer memory, which is used to store data temporarily. If you have tried to access or have accessed

confidential information requiring passwords (for example, your bank account), empty the cache of your

phone after each use.

Your phone supports up to 20 entries in the cache memory. This feature utilises the dynamic memory.

For more information see Dynamic memory on page 15.

To empty the cache memory when no WAP connection is in progress:

Press Menu, select Services, and Clear the cache.

To empty the cache memory when a WAP connection is in progress:

Press Options and select Clear the cache.

Security indicator

If the security indicator

is displayed during a WAP connection, the data transmission between the

phone and the WAP gateway or WAP server (identified by the IP address in the Edit active service

settings) is encrypted.

However, the security indicator does not indicate that the data transmission between the gateway and

the content server (the location where the requested resource is stored) is secure. It is up to the service

provider to secure the data transmission between the gateway and the content server.

Security module

The security module provides security services for WAP-related applications, and allows the use of the

phone’s digital signature functionality. If present, the security module is in the SIM card as an optional

100

service of your service provider. It can contain certificates, as well as private and public keys to operate

the certificates. The certificates and keys are stored in the security module by the SIM card issuer or

service provider.

Digital signature

With the digital signature functionality you can, for example, digitally sign a bill or a financial

contract. The signature can be traced back to you via the private key and the associated certificate that

was used to perform the signature, so signing using the digital signature is the same as signing your

name to a paper bill, contract or other document.

A digital signature is initiated by a code embedded in a WAP page. See also Access codes on page 14.

Select a product you want to buy and the digital signature procedure starts and shows the text to sign.

At this point check that the header text is Read and the digital signature icon

is shown.

Note: If the digital signature icon does not appear, there is a security breach, and you should

not enter any personal data such as your signing PIN.

To sign the displayed text, select Sign, after you have read all of the text.

Note: The text may not fit within a single screen. Therefore, make sure to scroll through and

read all of the text before signing.

Select the user certificate you want to use. Key in the signing PIN and press OK. Since the PIN code will

not be sent outside the phone, it will remain secret. The phone displays a confirmation Code accepted.

If you entered a wrong PIN, an error note Code error is displayed, and the phone asks you to key in the

PIN code again. After the confirmation has been displayed, the digital signature icon will disappear,

and browsing continues. The WAP service may display a confirmation of your purchase.

Certificates

There are three kinds of certificates:

101

• Server certificates

A server certificate is sent from the server to the phone and its validity is checked using the

authority certificates stored in the security module. This way you can be certain that a WAP

gateway or a WAP server is the one it claims to be.

You will see a note on the phone display if the identity of the WAP server or WAP gateway cannot

be verified, if the WAP server or WAP gateway certificate is not authentic or if you do not have the

right authority certificate in your phone.

• Authority certificates

Authority certificates are used by some WAP services, such as banking services, for checking

signatures or server certificates or other authority certificates.

• User certificates

User certificates are issued to users by a Certifying Authority. They associate a user with a specific

private key in a security module.

Security module settings

Press Menu, select Services, Settings and Security module settings. If there is no security module in the

phone, Insert security module is displayed.

In the Security module settings menu you have the following options:

•

Security module details shows the security module label, its status, manufacturer and serial

number.

•

Module PIN request , if On is selected the module PIN will be requested. The module PIN is supplied

with the SIM card.

102

•

Change module PIN shows a list of module PINs in alphabetical order if you have more than one

module PIN in your phone. The module PIN is supplied with the SIM card. Select the PIN you want to

change.

Change signing PIN shows a list of signing PINs in alphabetical order if you have more than one

signing PIN in your phone. The signing PIN is supplied with the SIM card. Select the PIN you want to

change.

If you key in a wrong PIN code several times, the phone may display PIN code blocked and ask you to

key in the PUK code. Contact your service provider to get the PUK code, and key it in. To key in the PUK

code later, you must first try to use the PIN, and you will then be asked for the PUK code.

■ SIM services (Menu 14)

In addition to the functions available on the phone, your SIM card may provide additional

services that you can access in menu 14. Menu 14 is shown only if it is supported by your

SIM card. The name and contents of the menu depend entirely on the service available.

Note: For availability, rates and information on using SIM services, contact your SIM card vendor, e.g.

network operator, service provider or other vendor.

You can set the phone to show you the confirmation messages sent between your phone and the

network when you are using the SIM services by selecting the option Yes within the menu 4-4-5,

Confirm SIM service actions.

Note that accessing these services may involve sending a text message (SMS) or making a phone call

for which you may be charged.

103

8. Data and fax communication

You can transfer data to other compatible devices when your Nokia 6310i mobile phone is connected

to a compatible PC via an IR connection, cable or Bluetooth.

To send and receive e-mail and faxes, and to connect to computers and access the Internet, you also

need the appropriate data and fax communications software installed on your computer. You can use

the Nokia 6310i mobile phone with a variety of commercially available data and fax communications

applications.

To use your phone as a modem, you first need to install it as a modem.

■ Communication applications and modem drivers

On the Nokia website, www.nokia.com/phones/6310i, you can find the required system files for data

communication and also the instructions for installation. You can also find documents that advise you

on how to set up devices and applications for use with the Nokia 6310i mobile phone.

PC Suite

PC Suite contains applications which help you

• to conveniently manage various phone functions from your PC

• to synchronise contacts and calendar items between your phone and your PC Personal Information

Manager.

• to draw and edit caller group graphics and picture messages.

• to create new ringing tones for your phone.

104

• to select the connection type used when connecting your PC and your phone.

• to back up and restore personal information from phone to PC or to another phone.

• to install Java applications from PC to your phone.

Modem setup

Modem setup installs the following components on your PC:

• Nokia 6310i data and fax modem adapters which enable you to use your phone as a modem in data

and fax calls.

• Nokia Modem Options software to set options for the data calls you make. Here you find the

settings for HSCSD and GPRS.

GPRS - General Packet Radio Service

See also GPRS modem settings on page 67.

HSCSD - High-Speed Circuit Switched Data

With the GSM high-speed data service, you can use the Internet and other services more quickly than

usual. When sending and receiving e-mail, the 14.4 kbps data transmission speed can be doubled up to

28.8 kbps. In Internet connections, a download speed of up to 43.2 kbps can be achieved if supported

by the equipment of the network operator and the Internet service provider.

Note that sending data in HSCSD mode drains the phone’s battery faster than normal voice or data

calls as the phone is sending data faster. For continuous usage, connect the phone to a charger.

105

Using data communication applications

• Activate the IR connection (Menu 9) or Bluetooth connection (Menu 10) of your phone, or connect

to the other device via the cable.

• If you are using the IR connection, make sure that the infrared port of the phone faces the infrared

port of the PC.

• Start using the data communications application on the PC.

For information on the use of the application, refer to the documentation for the application.

Note that making or answering phone calls during a PC connection is not recommended as it might

disrupt the operation.

For better performance during data calls, place the phone on a stationary surface with the keypad

facing downward. Do not move the phone by holding it in your hand during a data call.

106

9. Battery statements

■ Charging and Discharging

Your phone is powered by a rechargeable battery.

Note that a new battery’s full performance is achieved only after two or three complete charge and discharge

cycles!

The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating

time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

Use only batteries approved by the phone manufacturer and recharge your battery only with the chargers approved

by the manufacturer. Unplug the charger when not in use. Do not leave the battery connected to a charger for

longer than a week, since overcharging may shorten its lifetime. If left unused a fully charged battery will discharge

itself over time.

Temperature extremes can affect the ability of your battery to charge.

Use the battery only for its intended purpose.

Never use any charger or battery which is damaged.

Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object (coin, clip or pen)

causes direct connection of the + and - terminals of the battery (metal strips on the battery) for example when you

carry a spare battery in your pocket or purse. Short circuiting the terminals may damage the battery or the

connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the

capacity and lifetime of the battery. Always try to keep the battery between 15 °C and 25 °C. A phone with a hot or

cold battery may temporarily not work, even when the battery is fully charged. Batteries' performance is

particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire!

Dispose of batteries according to local regulations (e.g. recycling). Do not dispose of as household waste.

107

CARE AND MAINTENANCE

Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions

below will help you to fulfil any warranty obligations and to enjoy this product for many years.

•

Keep the phone and all its parts and accessories out of the reach of small children.

Keep the phone dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will

corrode electronic circuits.

•

Do not use or store the phone in dusty, dirty areas. Its moving parts can be damaged.

Do not store the phone in hot areas. High temperatures can shorten the life of electronic devices, damage

batteries, and warp or melt certain plastics.

•

Do not store the phone in cold areas. When it warms up (to its normal temperature), moisture can form inside,

which may damage electronic circuit boards.

•

Do not attempt to open the phone. Non-expert handling may damage it.

Do not drop, knock or shake the phone. Rough handling can break internal circuit boards.

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the phone.

Do not paint the phone. Paint can clog the moving parts and prevent proper operation.

Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications or

attachments could damage the phone and may violate regulations governing radio devices.

All of the above suggestions apply equally to your phone, battery, charger or any accessory. If any of them is not

working properly, take it to your nearest qualified service facility. The personnel there will assist you and, if

necessary, arrange for service.

108

IMPORTANT SAFETY INFORMATION

■ Traffic Safety

Do not use a hand-held telephone while driving a vehicle. Always secure the phone in its holder; do not place the

phone on the passenger seat or where it can break loose in a collision or sudden stop.

Remember road safety always comes first!

■ Operating environment

Remember to follow any special regulations in force in any area and always switch off your phone whenever it is

forbidden to use it, or when it may cause interference or danger.

Use the phone only in its normal operating positions.

Parts of the phone are magnetic. Metallic materials may be attracted to the phone, and persons with a hearing aid

should not hold the phone to the ear with the hearing aid. Always secure the phone in its holder, because metallic

materials may be attracted by the earpiece. Do not place credit cards or other magnetic storage media near the

phone, because information stored on them may be erased.

■ Electronic devices

Most modern electronic equipment is shielded from radio frequency (RF) signals. However, certain electronic

equipment may not be shielded against the RF signals from your wireless phone.

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 20 cm be maintained between a handheld

wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are

consistent with the independent research by and recommendations of Wireless Technology Research. Persons with

pacemakers:

109

•

Should always keep the phone more than 20 cm from their pacemaker when the phone is switched on.

Should not carry the phone in a breast pocket.

Should use the ear opposite the pacemaker to minimise the potential for interference.

If you have any reason to suspect that interference is taking place, switch off your phone immediately.

Hearing aids

Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may

want to consult your service provider.

Other medical devices

Operation of any radio transmitting equipment, including cellular phones, may interfere with the functionality of

inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to

determine if they are adequately shielded from external RF energy or if you have any questions. Switch off your

phone in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health

care facilities may be using equipment that could be sensitive to external RF energy.

Vehicles

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (e.g.

electronic fuel injection systems, electronic anti-skid (anti-lock) braking systems, electronic speed control systems,

air-bag systems). Check with the manufacturer or its representative regarding your vehicle. You should also

consult the manufacturer of any equipment that has been added to your vehicle.

Posted facilities

Switch your phone off in any facility where posted notices so require.

110

■ Potentially explosive atmospheres

Switch off your phone when in any area with a potentially explosive atmosphere and obey all signs and

instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death.

Users are advised to switch off the phone when at a refuelling point (service station). Users are reminded of the

need to observe restrictions on the use of radio equipment in fuel depots (fuel storage and distribution areas),

chemical plants or where blasting operations are in progress.

Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on

boats; chemical transfer or storage facilities; vehicles using liquified petroleum gas (such as propane or butane);

areas where the air contains chemicals or particles, such as grain, dust or metal powders; and any other area where

you would normally be advised to turn off your vehicle engine.

■ Vehicles

Only qualified personnel should service the phone, or install the phone in a vehicle. Faulty installation or service

may be dangerous and may invalidate any warranty which may apply to the unit.

Check regularly that all wireless phone equipment in your vehicle is mounted and operating properly.

Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the phone, its

parts or accessories.

For vehicles equipped with an air bag, remember that an air bag inflates with great force. Do not place objects,

including both installed or portable wireless equipment in the area over the air bag or in the air bag deployment

area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Using your phone while in the air is prohibited. Switch off your phone before boarding an aircraft. The use of

wireless telephones in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone

network and may be illegal.

Failure to observe these instructions may lead to suspension or denial of telephone services to the offender, or legal

action or both.

111

■ Emergency calls

Important:

This phone, like any wireless phone, operates using radio signals, wireless and landline networks as well as

user-programmed functions. Because of this, connections in all conditions can not be guaranteed.

Therefore, you should never rely solely upon any wireless phone for essential communications (e.g.

medical emergencies).

Emergency calls may not be possible on all wireless phone networks or when certain network services and/

or phone features are in use. Check with local service providers.

To make an emergency call:

1. If the phone is not on, switch it on. Check for adequate signal strength.

Some networks may require that a valid SIM card is properly inserted in the phone.

2. Press

as many times as needed (e.g. to exit a call, to exit a menu, etc.) to clear the display and ready the

phone for calls.

3. Key in the emergency number for your present location (e.g. 112 or other official emergency number).

Emergency numbers vary by location.

4. Press the

key.

If certain features are in use, you may first need to turn those features off before you can make an emergency call.

Consult this guide and your local cellular service provider.

When making an emergency call, remember to give all the necessary information as accurately as possible.

Remember that your wireless phone may be the only means of communication at the scene of an accident - do not

cut off the call until given permission to do so.

112

■ Certification information (SAR)

THIS MODEL PHONE MEETS THE EU REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

Your mobile phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the limits for

exposure to radio frequency (RF) energy recommended by The Council of the European Union. These limits are part

of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines

were developed by independent scientific organisations through periodic and thorough evaluation of scientific

studies. The limits include a substantial safety margin designed to assure the safety of all persons, regardless of age

and health.

The exposure standard for mobile phones employs a unit of measurement known as the Specific Absorption Rate, or

SAR. The SAR limit recommended by The Council of the European Union is 2.0 W/kg.* Tests for SAR have been

conducted using standard operating positions with the phone transmitting at its highest certified power level in all

tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level

of the phone while operating can be well below the maximum value. This is because the phone is designed to

operate at multiple power levels so as to use only the power required to reach the network. In general, the closer

you are to a base station antenna, the lower the power output.

Before a phone model is available for sale to the public, compliance with the European R&TTE directive must be

shown. This directive includes as one essential requirement the protection of the health and the safety for the user

and any other person. The highest SAR value for this model phone when tested for compliance against the standard

was 0.82 W/kg. While there may be differences between the SAR levels of various phones and at various positions,

they all meet the EU requirements for RF exposure.

* The SAR limit for mobile phones used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams of tissue.

The limit incorporates a substantial margin of safety to give additional protection for the public and to account for

any variations in measurements. SAR values may vary depending on national reporting requirements and the

network band. For SAR information in other regions please look under product information at www.nokia.com.

113

LIMITED MANUFACTURER’S WARRANTY

PART OF EUROPE & AFRICA REGION

This limited warranty shall apply in part of Nokia

which all by their nature have a limited lifetime, and

breakage or damage to antennas) unless the defect

was caused directly by defects in materials, design or

workmanship;

Mobile Phones’ Europe & Africa Region unless a local

warranty exists. Nokia Corporation, Nokia Mobile

Phones (”Nokia”) warrants that this NOKIA product

(”Product”) is at the time of its original purchase free

of defects in materials, design and workmanship

subject to the following terms and conditions:

(ii) Nokia or its authorized service company was not

notified by the Customer of the defect within thirty

(30) days after the appearance of the defect within

the warranty period;

1. This limited warranty is given to the end-purchaser

of the Product (”Customer”). It shall neither

exclude nor limit i) any mandatory statutory rights

of the Customer or ii) any of the Customer’s rights

against the seller/dealer of the Product.

(iii) the Product was not returned to Nokia or its

authorized service company within thirty (30) days

after the appearance of the defect within the

warranty period;

2. The warranty period is twelve (12) months from

the date on which the first Customer purchased

the Product. In case of a subsequent purchase or

other change of owner/user, such warranty period

shall continue for the remaining part of the twelve

(12) month period and otherwise remain

unaffected. This limited warranty is only valid and

enforceable in the following countries: Bosnia,

Bulgaria, Croatia, Cyprus, the Czech Republic,

Estonia, any member state of the European Union,

Hungary, Iceland, Israel, Latvia, Lithuania,

Macedonia, Malta, Norway, Poland, Romania, the

Slovak Republic, Slovenia, Switzerland and Turkey.

(iv) the Product serial number, the accessory date

code or the IMEI number has been removed, erased,

defaced, altered or is illegible;

(v) the defect was caused by a defective function of

the cellular network;

(vi) the defect was caused by the fact that the

Product was used with or connected to an accessory

not manufactured and supplied by Nokia or used in

other than its intended use;

(vii) the defect was caused by the fact that the

battery was short-circuited or seals of the battery

enclosure or cells were broken or show evidence of

tampering or the battery was used in equipment

other than for which it has been specified; or

3. During the warranty period Nokia or its authorized

service company will repair or replace, at Nokia’s

sole discretion, a defective Product. Nokia will

return the repaired Product or another Product to

the Customer in good working condition. All parts

or other equipment for which replacements have

been provided shall become the property of Nokia.

(viii) the Product software needs to be upgraded due

to changes in cellular network parameters.

4. A repaired or replaced Product will not be given a

prolonged or renewed warranty period.

7. To claim this limited warranty the Customer shall

present either i) a legible and non-modified

original warranty card which clearly indicates the

name and address of the seller, the date and place

of purchase, the product type and the IMEI or

other serial number or alternatively ii) a legible and

non-modified original purchase receipt which

contains the same information, if such purchase

receipt is presented to the seller/dealer of the

Product.

5. This limited warranty will not cover painted covers

or other similar personalized parts. In all cases that

require unlocking or locking of an operator SIM-

lock, Nokia will first direct the Customer to such

operator for unlocking or locking of the operator

SIM-lock before repairing or replacing the Product.

6. This limited warranty shall not apply to

deterioration due to normal wear and tear. This

limited warranty shall further not apply if:

8. This limited warranty is the Customer’s sole and

exclusive remedy against Nokia and Nokia’s sole

and exclusive liability against the Customer for

defects or malfunctions of the Product. This limited

warranty replaces all other warranties and

liabilities, whether oral, written, (non-mandatory)

statutory, contractual, in tort or otherwise. Nokia is

in no event liable for any incidental, consequential

or indirect damage, costs or expenses. Neither is

Nokia in any event liable for any direct damage,

costs or expenses, if the Customer is a legal person.

(i) the defect was caused by the fact that the Product

has been subjected to: use in contradiction with the

owner’s/user manual, rough handling, exposure to

moisture, dampness or extreme thermal or

environmental conditions or rapid changes in such

conditions, corrosion, oxidation, unauthorized

modifications or connections, unauthorized opening

or repair, repair by use of unauthorized spare parts,

misuse, improper installation, accident, forces of

nature, spillage of food or liquid, influence from

chemical products or other acts beyond the

9. Any change or amendment to this limited warranty

requires Nokia’s prior written consent.

reasonable control of Nokia (including but not limited

to deficiencies in consumable parts, such as batteries

9359974/02

WARRANTY CARD

FILL IN WITH BLOCK LETTERS

Purchaser’s Name: _____________________________________________________

Address: _____________________________________________________________

_____________________________________________________________

Country: _____________________________________________________________

Phone: ______________________________________________________________

Date of Purchase (dd/mm/yy):

Product Type (on phone type label under battery):

Product Model (on phone type label under battery):

Phone Serial No (on phone type label under battery):

–

Place of Purchase: _____________________________________________________

Store Name:__________________________________________________________

Store Address: ________________________________________________________

Stamp

Sony Xperia tipo 1264 0772 User Manual
Sony CDP 608ESD User Manual
Seagate ST3200827SCE User Manual
Seagate ST612712DE User Manual
Seagate ST31720A User Manual
Samsung SGH T679DBBTMB User Manual
Samsung DLP TV SP50L6HX User Manual
Pioneer CDJ 1000MK2 User Manual
Packard Bell EXPRESS ST8000 User Manual
Nokia NSERIES N96 User Manual