OWNER'S OPERATING AND MAINTENANCE MANUAL
505
Task Chair
without Armrests
506
Task Chair with
Adjustable Armrests
4300-4308-4350-4358-4400
-4408-4450-4458
Gas-Liſt Task Seating
435
445
507
Gas-Liſt
Task Seating
430
440
Task Seating
1-800-237-3377
CHAMPIONCHAIR.COM
Document No. 006350 Rev A
TABLE OF CONTENTS
Important Safety Information..................................................................................................... 4
Transportation, Storage, Handling & Disposal ........................................................................ 4
505 Task Chair without Armrests................................................................................................ 5
506 Task Chair with Adjustable Armrests.................................................................................. 5
Base Assembly ......................................................................................................................... 5
Back Assembly ......................................................................................................................... 5
Arm Installation for 506 Model Only..................................................................................... 6
Operation of Task Chair.......................................................................................................... 6
507 4300 4308 4350 4358 4400 4408 4450 4458 Gas-Lift Task Seating................................ 8
Base Assembly ......................................................................................................................... 8
Back Assembly ......................................................................................................................... 8
Operation of Gas Lift Stool..................................................................................................... 9
GENERAL CARE & CLEANING....................................................................................................... 10
Specifications................................................................................................................................. 11
Page 3 of 13
manual
Document No.: 006350 - Revision: A
IMPORTANT: PLEASE READ
READ AND FOLLOW ALL DIRECTIONS.
1. NEVER stand on chair or INJURY MAY OCCUR.
2. KEEP HANDS CLEAR of moving parts when adjusting movable parts on chair or INJURY MAY OCCUR.
3. DO NOT use chair for transporting user in or with ANY type of vehicle of trailer. Chairs have not been tested
or approved for use by an occupant in any type of vehicle or trailer.
4. NEVER leave an infant or child unattended on chair or INJURY MAY OCCUR.
5. DO NOT allow children to play on or with chair or INJURY MAY OCCUR.
6. Periodically, recheck tightness of all nuts, bolts, and screws.
7. USE ONLY CHAMPION AUTHORIZED REPLACEMENT PARTS.
8. NEVER EXCEED the recommended weight capacity of:
505 – 506 – 507: 300 lbs. (136 kg)
4300 – 4308 – 4350 – 4358 – 4400 – 4408 – 4450 – 4458: 250 lbs. (113.4 kg)
9. SAVE THESE INSTRUCTIONS for future reference and training.
TRANSPORTATION, STORAGE, HANDLING & DISPOSAL
•
The product should be transported in factory packaging, inside an appropriate medium for the
destination, i.e., air/sea cargo containers.
•
•
The product should be stored in an environment that will inhibit rust/mold formation.
Champion Manufacturing, Inc recommends not leaving the product in the factory packing in excess of
three (3) months.
•
•
The product should always be handled in a manner consistent with the user instructions and in a
manner to prevent contamination after each use.
The product has many recyclable components and to the extent practical, all effort should be used to
recycle responsibly. Otherwise the product components shall be disposed of in accordance with local
statutes.
NOTE: No tools are required for installation.
Page 4 of 13
manual
Document No.: 006350 - Revision: A
505 TASK CHAIR WITHOUT ARMRESTS
FIG. 1
506 TASK CHAIR WITH ADJUSTABLE
ARMRESTS
BASE ASSEMBLY
1. Place the 5-Star Chair Base on a clean, flat surface with wheels down.
FIG. 2
2. Push the large end of the Gas Cylinder into the center hole of the 5-Star
Chair Base. Press base and cylinder together firmly to secure (Fig. 1).
*Foot Ring Option – Slide the Foot Ring over the Gas Cylinder and
tighten the Foot Ring Knob (Fig. 2).
3. Install the Chair Seat over the end of the Gas Cylinder. Press Seat and
Cylinder together firmly to secure (Fig. 3).
BACK ASSEMBLY
4. On the bottom of the Seat Plate, remove the Knob and Hardware (Fig. 4
& 7).
5. Slide the Steel Back Support of the Upholstered Back into the
narrow slot on the rear of the Seat Plate and fasten with the Knob and
Hardware (Fig. 5).
FIG. 3
6. On the backside of the Upholstered Back, remove the Knob and
Hardware. Insert the threaded stud of the back hinge through the slot on
the Steel Back Support. Reinstall the Knob and Hardware to secure the
Upholstered Back. Adjust the Backrest and Seat Knobs as needed for
individual comfort (Fig. 6).
FIG. 4
SEAT, BACK & BASE ASSEMBLY IS COMPLETE.
FIG. 6
FIG. 5
FIG. 7
Page 5 of 13
manual
Document No.: 006350 - Revision: A
ARM INSTALLATION FOR 506 MODEL ONLY
7. Remove the Arm Support Adjustment Knob and Hardware from the
Adjustable Armrest.
8. Slide the Adjustable Armrest into the Armrest Bracket located under
each side of the Upholstered Seat. Secure the Adjustable Armrest by
installing the Arm Support Adjustment Knob and Hardware through
the slot in the Adjustable Armrest and into the threaded holes of the
mounting plate (Fig. 8).
FIG. 8
FIG. 9
NOTE: The longer part of the arm should be closest to the front of
the chair (Fig. 9).
9. Repeat for opposite side.
ARM INSTALLATION IS COMPLETE.
OPERATION OF TASK CHAIR
1. The chair is now ready for use. To raise the seating height, liſt Release
Handle without weight on seat.
2. To lower seating height, Liſt the Release Handle while sitting on the seat;
Release the handle when desired height is reached.
3. Position the Adjustable Armrest to desired height by pulling up on the
Arm Height Release Lever and moving the Adjustable Armrest up or
down. Release the lever to lock armrest in place.
Periodically recheck tightness of all fasteners,
and never stand on the Upholstered Seat.
Page 6 of 13
manual
Document No.: 006350 - Revision: A
IMPORTANT:
•
HIGH RESISTANCE (HR) CASTERS – Your Champion task chair may be equipped with High
Resistance (HR) casters. HR casters allow casters to roll freely when weighted or occupied but
resist rolling when unweighted or when exiting the task chair. Standard casters always roll freely
and may allow the task chair to move away from the occupant when leaving or entering the task
chair. The potential for this unintended/unweighted movement may be reduced with the use of
HR casters. Task chair users should be always attentive to their chair position when entering or
exiting the chair.
•
•
NOTE: HIGH RESISTANCE (HR) CASTERS MAY NOT RELEASE AND ROLL FREELY IF YOU WEIGH LESS
THAN 80 POUNDS. High Resistance Casters look the same as standard casters and may not be
easily distinguished from standard casters other than by loading and unloading them in a test.
If your Champion task chair did not come with the HR Caster option, and you would like to add
them, please contact Champion Mfg. for pricing and assembly instructions. Championchair.com
(352) 854-2929.
WRINKLES IN VINYL – Storage and shipping can cause wrinkles of the vinyl on your Champion task
chair. This is normal. Please allow 1 – 2 weeks at room temperature (approx. 70 degrees) to allow
for vinyl to expand back to original appearance.
Page 7 of 13
manual
Document No.: 006350 - Revision: A
507 GAS-LIFT TASK SEATING
FIG. 1
4300 4308 4350 4358 4400 4408 4450 4458
GAS-LIFT TASK SEATING
BASE ASSEMBLY
1. Place the 5-Star Chair Base (black plastic or chrome) on a clean, flat
surface with bottom facing up (Fig. 1).
FIG. 2
2. Install all (5) Casters into the Base (the stem of the caster should snap
into place) and then flip the Base upright, with wheels facing down (Fig.
2 & 3).
3. Push the stem of the Gas Cylinder into the 5-Star Chair Base (Fig. 3).
4. Slide the Foot Ring (optional) over the Gas Cylinder and tighten the
Foot Ring Knob (Fig. 4).
5. Install the Stool Seat over the end of the Gas Cylinder and push down
firmly on stool seat (Fig. 5).
BACK ASSEMBLY (FOR MODELS WITH BACKS ONLY)
6. Slide the steel Slotted Back Strap into the Stool Swivel Plate (Fig. 6).
7. Insert the Back (depth) Adjusting Knob to lock
FIG. 3
FIG. 5
the Slotted Back Strap into place (Fig. 7 & 8).
FIG. 4
ASSEMBLY IS COMPLETE.
FIG. 6
FIG. 8
FIG. 7
Page 8 of 13
manual
Document No.: 006350 - Revision: A
OPERATION OF GAS LIFT STOOL
1. The stool is now ready for use. To raise the stool seating height, liſt Release Handle without weight on seat.
2. To lower stool seating height, Liſt the Release Handle while sitting on the seat; Release the handle when
desired height is reached. Approximate Range = 17 to 23 inches.
3. Position the optional Upholstered Back and Foot Ring into the desired positions using the Adjusting
Knobs.
Periodically recheck tightness of all fasteners, and never stand on the Upholstered
Seat.
IMPORTANT:
•
HIGH RESISTANCE (HR) CASTERS – Your Champion task chair may be equipped with High
Resistance (HR) casters. HR casters allow casters to roll freely when weighted or occupied but
resist rolling when unweighted or when exiting the task chair. Standard casters always roll freely
and may allow the task chair to move away from the occupant when leaving or entering the task
chair. The potential for this unintended/unweighted movement may be reduced with the use of
HR casters. Task chair users should be always attentive to their chair position when entering or
exiting the chair.
•
•
NOTE: HIGH RESISTANCE (HR) CASTERS MAY NOT RELEASE AND ROLL FREELY IF YOU WEIGH LESS
THAN 80 POUNDS. High Resistance Casters look the same as standard casters and may not be
easily distinguished from standard casters other than by loading and unloading them in a test.
If your Champion task chair did not come with the HR Caster option, and you would like to add
them, please contact Champion Mfg. for pricing and assembly instructions. Championchair.com
(352) 854-2929.
WRINKLES IN VINYL – Storage and shipping can cause wrinkles of the vinyl on your Champion task
chair. This is normal. Please allow 1 – 2 weeks at room temperature (approx. 70 degrees) to allow
for vinyl to expand back to original appearance.
Page 9 of 13
manual
Document No.: 006350 - Revision: A
GENERAL CARE & CLEANING
•
Periodically inspect tightness of all screws, bolts, nuts, or other fasteners.
Champion furnishings are built to provide durable reliable service when properly cared for. In general all of our
products should be: 1) Cleaned, 2) Rinsed and 3) Allowed to air dry. It is important to note that disinfecting a
product is not the same as cleaning the product. Disinfectants alone will not provide adequate cleaning, they
do not have grease or oil cutting properties to remove grime or hair and skin oils. Over time, the appearance and
feel and performance of your upholstery may diminish if not cleaned properly.
CLEANING
Remove grime, hair, and body oils; Your furnishings should be cleaned with mild soap & water solution and a
damp cloth on a regular basis. Avoid harsh detergents that could damage the finish of your product.
NOTE: If the furnishing is disinfected with bleach, it MUST be wiped off using only clean water on a damp
cloth and then be allowed to air dry. Failure to rinse with clean water can result in a build-up of residues
over time that can damage your product.
For additional cleaning information please visit www.championchair.com/cleaning-instructions/
Page 10 of 13
manual
Document No.: 006350 - Revision: A
IMPORTANT: ALWAYS REFER TO THE WEIGHT CAPACITY LABEL ON
YOUR CHAIR.
In all cases the labeling on the chair at the time of delivery indicates the correct rating for your chair –
Weight rating should not be exceeded!
SPECIFICATIONS
Task Stools
430
440
507
Min. Seat Height
Max. Seat Height
Overall Height
Seat Diameter/Width
Weight Capacity
Footprint
19” (48 cm)
21.5” (54.61 cm)
19” (48 cm)
16.5” (41.91 cm)
250 lb (113.40 kg)
22” (55.88 cm)
Impact Plastic
17.75” (45.09 cm)
23” (58.42 cm)
17.75” (45.09 cm)
16.5” (41.91 cm)
250 lb (113.40 kg)
22” (55.88 cm)
16.5” (41.91 cm)
34” - 43”
15”
300 lb.
22” (55.88 cm)
Composite Base
Base Type High
Polished Aluminum
Task Chairs
435
445
505
506
Min. Seat Height
Max. Seat Height
Seat Back Height
Overall Height
17” (43.18 cm)
22.75” (57.79 cm)
13” (33.02 cm)
29” - 34”
(73.7 cm – 86.4 cm)
18.25” (46.36 cm)
23.25” (59.06 cm)
13” (33.02 cm)
30” - 35”
(76.2 cm – 88.9 cm)
21″ (53.3 cm)
28" (71.1 cm)
21″ (53.3 cm)
28" (71.1 cm)
37″ – 46.5″
(94 cm – 118.1 cm)
37″ – 46.5″
(94 cm – 118.1 cm)
Seat Diameter/Width
Weight Capacity
Footprint
16.5” (41.91 cm)
250 lb (113.40 kg)
22” (55.88 cm)
16.5” (41.91 cm)
250 lb (113.40 kg)
22” (55.88 cm)
19″
300 lb
26.5″
19″
300 lb
26.5″
Base Type
High Impact Plastic
Polished Aluminum
High Impact Plastic
High ImpactPlastic
IMPORTANT: Maximum Weight Capacity should be evenly distributed.
Page 11 of 13
manual
Document No.: 006350 - Revision: A
Visit our website (ChampionManufacturing .com) to view our full line of
medical furnishings and procedure-chairs.
Additional copies of this manual and other product documents are available for download via the resources
section of our website.
SPECIFICATIONS SUBJECT TO CHANGE
While we endeavor to maintain consistent products, due to conditions beyond our control, specifications
are subject to change without notice. We reserve the right to add or delete products at any time
and without prior notice. Always provide your product's specific serial number when ordering any
replacement parts. When in doubt, contact a Champion representative (352-854-2929 or 1-800-237-3377)
for further information.
Page 12 of 13
manual
Document No.: 006350 - Revision: A
Information contained in this document is based on the latest product data available at the time of printing. Photography, artwork, text and specifications are subject to change. Photographs may show
optional items. Champion Manufacturing Inc. reserves the right to make changes to products, materials, options, and/or specification at any time without notice or obligation. Always provide your
product's specific serial number when ordering replacement parts. Contact Champion direct for additional information and the latest specifications.
© 2023 Champion Manufacturing Inc. Document No.: 006350 Revision: A
|