i856
User’s Guide
Class B Digital Device
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
As a personal computer peripheral, this device complies with part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. See 47 CFR Sec. 15.19(3).
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i856
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Model Number: H74XAN6JR7AN
FCC-ID: IHDT56KC1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
FCC Notice to Users
The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC logo,
and/or an FCC ID in the format FCC-ID: IHDT56KC1 on the product
label.
Motorola has not approved any changes or modifications to this device by
the user. Any changes or modifications could void the user’s authority to
operate the equipment. See 47 CFR Sec. 15.21.
•
Consult the dealer or an experienced radio/TV technician for
help.
Industry Canada Notice to Users
Operation is subject to the following two conditions: (1) This device may
not cause interference and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
See RSS-GEN 7.1.5.
Motorola, Inc.
Consumer Advocacy Office
600 North US Highway 45
Libertyville, IL 60048
www.hellomoto.com
Note: Do not ship your phone to the above address. If you need to
return your phone for repairs, replacement, or warranty service,
please contact the Motorola Customer Support Center at:
1-800-453-0920 (United States)
1-877-483-2840 (TTY/TDD United States for hearing impaired)
Certain mobile phone features are dependent on the capabilities
and settings of your service provider’s network. Additionally,
certain features may not be activated by your service provider,
and/or the provider's network settings may limit the feature’s
functionality. Always contact your service provider about feature
availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in this
user's guide are based upon the latest available information and
are believed to be accurate at the time of printing. Motorola
reserves the right to change or modify any information or
specifications without notice or obligation.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. All other product or service names are
the property of their respective owners. Java and all other
Java-based marks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
© Motorola, Inc., 2009.
Manual Number: NNTN7815A
HELLOMOTO
Introducing your new Motorola i856 wireless phone. Here’s a quick anatomy lesson.
i856w
Camera
Key
Right Soft Key
Perform function
in lower right
display.
Left Soft Key
Perform function
in lower left
display.
Ready
Ready
5/10/09
5/10/09
Menu Key
From home screen,
open main menu.
End/Power Key
End calls, exit
menu system,
turns phone
on/off.
Speaker Key
Volume Keys
PTT Button
Contcs
Mesgs
Contcs
Mesgs
OK / Play Key
Talk Key/Recent Call
Make &
Music Key
answer calls.
Activates Music
Player.
3.5 mm Audio Jack
Micro USB Connector
Connects charger and
accessories.
4-Way Navigation Key
1
check it out
1
Ready
Press and hold the
Power Key for a
few seconds, or until
the screen lights up,
to turn on your phone.
5/10/09
3
Press the Navigation key
up, down, left or right
to highlight a menu feature.
Contcs
Mesgs
2
Customizable rkey
that can be used
to open the
4
Settings screen.
Press the rkey
to select.
2
contents
call a stored phone
finding your phone
features for the hearing
my music . . . . . . . . . . 50
volume . . . . . . . . . . . . 41
SIM card. . . . . . . . . . . . 9
microSD memory card . 9
store a phone number or
contents
3
hide or show location
RF Energy Interference/
Caring for the
91
Open Source Software
Export Law Assurances. .
Specific Absorption Rate.
Hearing Aid Compatibility
Information From the
103
Wireless: The New
California Perchlorate
Patent and Trademark
Software Copyright Notice
Privacy and Data Security
Smart Practices While
Safety and General
Operational Precautions .
AGPS and Emergency
Motorola Limited
States and Canada. . . . 98
contents
4
menu map
main menu
B
L
Recent Calls
T
Games and Apps
•
•
Alarm Clock Plus
Bluetooth
•
•
•
•
•
•
•
Buy More
Contacts
•
Audio Devices
Pair to Devices
Device History
Setup
Alarm Clock Plus
My Images
•
•
[New Contact]
•
Audio Player
My Videos
Java System
Memory Card
E
Messages
•
•
•
•
•
•
•
•
•
[Create Message]
Find Me
Voice Mail
Inbox
•
GPS
•
•
•
Position
Privacy
Drafts
C
Tools
•
Outbox
My Info
Interface
Sent Items
Net Alert
•
•
•
•
•
•
•
My Name
Line 1
•
•
Datebook
•
[New Event]
Private ID1
Private ID2
Carrier IP
1
j
Web
Call Timers
•
•
•
•
•
•
Last Call
Multimedia
Phone Reset
IP1 Address
IP2 Address
Phone Lifetime
Prvt/Grp Reset
Prvt/Grp Lifetime
Kbytes Reset
•
•
•
•
•
•
•
•
Media Center
My Images
My Music
My Videos
Camera
•
Profiles
•
•
•
•
•
•
•
•
•
[New Profile]
Standard
Car
•
Memo
Camcorder
Ring Tones
VoiceRecord
u
Settings (see next page)
Meeting
Office
Outdoors
Headset
PRVT Only
CNTCS Only
This is the standard main menu layout. Your
phone’s menu may be a little different.
S
Push To Talk
•
•
•
•
Call Alert
PT Manager
Quick PTT
PTT Options
5
settings menu
Display/Info
•
•
•
•
•
•
•
•
•
Slide Activation
Minute Beep
Call Duration
TTY
Hearing Aid
Notifications
DTMF Dialing
Call Forward
Prepend
Memory Card
•
Wallpaper
•
•
•
•
Remove Card
•
•
•
[Buy More]
Store Media
Format Card
Help
Auto Cycle
Wallpaper
•
•
•
•
Text Size
Theme
Security
•
•
•
•
•
Phone Lock
Home Icons
Backlight
Keypad Lock
SIM PIN
•
•
•
Timer
Personalize
GPS PIN
Change Passwords
Java Timer
PTT Backlight
•
•
•
•
•
•
•
•
•
•
Reorder Menu
Shortcuts
Up Key
Advanced
•
•
Slide Close
•
•
•
•
•
•
•
Alert Timeout
•
•
Continue Task
Down Key
Left Key
Headset/Spkr
Connectivity
Reset Defaults
Return to Home
Transmitters
Phone Only
End Task
Clock
Right Key
Center Key
Left Softkey
Right Softkey
Power Up
•
•
•
•
Display
Time Format
Date Format
Year
•
Menu View
Connections
Volume
•
•
•
Icon View
List View
Tab View
•
•
Bluetooth
•
•
•
•
•
Ringers/Alerts
USB
Speaker
Earpiece
Multimedia
Keypad
•
•
•
•
Memory Card Access
Data Modem
Application Access
Help
•
•
Large Dialing
Language
Phone Calls
Voice Playback
•
•
•
•
•
Set Line
•
•
•
•
Speak Text
Any Key Ans
Auto Redial
Call Waiting
Auto Ans
Speak Caller
Voice
Multimedia Volume
6
use and care
Use and Care
To care for your Motorola phone, please keep it away from:
liquids of any kind
dust and dirt
Don’t expose your phone to water, rain,
extreme humidity, sweat, or other
moisture. If it does get wet, don’t try to
accelerate drying with the use of an
oven or dryer, as this may damage the
phone.
Don’t expose your phone to dust, dirt,
sand, food, or other inappropriate
materials.
extreme heat or cold
cleaning solutions
To clean your phone, use only a dry soft
cloth. Don’t use alcohol or other
cleaning solutions.
Avoid temperatures below 0°C/32°F or
above 45°C/113°F
.
microwaves
the ground
Don’t try to dry your phone in a
microwave oven.
Don’t drop your phone.
7
essentials
Caution: Before using the phone for the first
time, read the Important Safety and Legal
information included in the gray-edged pages
at the back of this guide.
2
Press the navigation keys
Phone Calls, and press the center key
select it.
;
to scroll to
r
to
symbols
This means a feature is network or
subscription dependent and may
not be available in all areas, or might
not be offered by your service
provider. Contact customer service
for more information.
about this guide
This guide shows how to locate and access
menu feature as follows:
Find it:
/
>
u
>
Phone Calls
This means that, from the home screen:
This means a feature requires an
optional accessory.
1
8
Press the menu key
the Settings menu option
/
and then press
u.
essentials
SIM card
microSD memory
card
Your handset may come with a memory card,
memory card adapter, and memory card
reader1.
insert the SIM card
A memory card is removable flash memory
you can use to store pictures, videos, and
audio files(music and podcast).
You can connect your phone using a
Motorola data cable directly to your
computer, access the memory card
loaded in the phone to save or delete music,
images, videos, or audio files.
Find it:
/
>
u
>
Connections > USB
Warning: To avoid loss or damage, do not
remove your SIM card from your phone
unless absolutely necessary.
1. Depending on your service provider, the memory card,
memory card adapter, and memory card reader may not
be included with your phone.
essentials
9
insert the memory card
remove the memory card
1
Remove the battery door, lift the black
plastic indicator and slide the memory
card in place. Return the battery cover
when you are done.
Warning: Do not remove the memory card
before selecting the Remove Card option under
Settings. Removing the memory card before
selecting the Remove Card option could result in
loss of data.
1
2
3
From the home screen press />
u
>
Memory Card > Remove Card
.
Once the handset confirms it is safe to
remove the SD card, press
-
under OK.
Remove the battery door.
Note: The first time you insert a memory card
in your phone, you will see the following
options: [Do Nothing] Go To Audio Player, Go To Camera,
,
and Go To Media Center. Select the option of your
choice and continue.
essentials
10
4
Lift the black plastic indicator and, with
your fingernail, slide the memory card out
of the slot.
battery
Safety” on page 94 before using this product.
battery installation
1
With your fingernail, pull the battery
door cover lock toward the front of the
phone.
5
Close the memory card slot cover.
essentials
11
2
Slide the battery door upwards until it is
released from the phone.
4
Push the battery down until it snaps in
place.
5
Replace the battery door and slide it
down while pressing gently until you
hear a click.
battery charging
New batteries are not fully charged.
3
Remove the battery door.
Note: You must remove the battery
door to attach a lanyard to the phone.
essentials
12
charge using the charger
high-power connectors are located directly on
your computer.
1
Pull out the connector cover, and insert
the charger into the micro USB connector
on your phone as shown.
turn it on & off
To turn on your phone, press and hold
.
for
a few seconds or until the display turns on. If
prompted, enter your four-digit unlock code.
charge from your computer
To turn off your phone, press and hold
two seconds.
.
for
You can partially charge your phone’s
battery by connecting a Motorola-approved
USB cable from your phone’s micro-USB port
to a high power USB connector on a
computer (not a low-power one, such as the
USB connector on your keyboard or
Note: If you press the
.
for more than four
seconds, the handset will power “On” in
bus-powered USB hub). Typically, USB
essentials
13
enable security
answer a phone call
You must enable security the first time you
power on you phone or within 10 days of first
activation of your phone.
1
2
3
If you want to answer the call on speaker
phone, press the speaker key
)
.
If you want to answer the call using the
handset, press . To hang up press
1
2
Press
You are prompted to enable security.
Press under Yes. A series of screens
K
under Ok
.
,
..
If you are using a Bluetooth headset,
press the answer key on your headset. To
hang up press the key again.
K
followed by the default home page
displays.
3
Press
.
to return to the home screen.
advanced calling
feature
make a phone call
call waiting To accept the second call
and put the active call on
Enter a phone number and press
voice command. See “place a call using a
,
or use a
hold press
K
under Yes.
To accept the second call
and end the active call press
To hang up press
..
.
.
essentials
14
Note: A Private call ends automatically if there
is no activity on the call for a few seconds.
feature
any key
answer
To answer phone calls by
pressing any key on the
send call alerts
Sending a call alert discretely lets the
recipient know that you want to talk to him or
her on a Private call.
keypad press
/
>
u
>
>
On
Phone Calls
>
Any Key Ans
.
make a private call
Your Private ID is the number at which you
receive one-to-one Private calls.
When you send a call alert, the recipient’s
handset displays your name and emits a
series of beeps or vibrations.
Note: PTT means Push To Talk/ Walkie-Talkie.
to send a call alert
to make a Private call
1
Enter the Private ID you want to call as
you would when making a Private call.
1
Enter the Private ID you want to call.
2
Press
K
under Alert.
2
Press and hold the PTT button. Begin
talking after your phone emits a chirping
sound.
When the message Ready To Alert appears on
the display, press the PTT button until the
message Alert Successful appears.
3
Release the PTT button to listen.
To end the call press
..
essentials
15
You cannot receive phone calls or Private calls
until you do.
answer a private call
1
When your phone emits a chirping sound
or vibrates to indicate you are receiving a
Private call, wait for the caller to finish
speaking.
to answer a call alert
1
2
3
Press the PTT button to start a Private call
with the sender.
or
2
3
Press and hold the PTT button and begin
talking after your phone emits a chirping
sound.
Queue the call alert by pressing
K
under
Queue
.
Release the PTT button to listen.
or
To end the call press
..
Clear the call alert by pressing
K
under
Clear
.
answer a call alert
making a phone call while in a
private call
When you are in a Private call, you can make a
phone call to the other participant if that
person’s phone number is stored in Contacts.
When you receive a call alert, you must:
option
Answer: Begin a Private call with the sender.
Queue: Store the call alert to the call alert
queue.
1
While in a Private call press
,.
Clear: Dismiss and delete the call alert.
essentials
16
2
3
A confirmation screen will appear asking
to Start Call To:.
4
Enter the number for the entry and press
under Save when done.
K
Press
K
under Yes or press
r
to begin
the call.
contacts
feature
store a phone number
or private ID
edit/delete Press
contact Select a contact and press
entry Edit. Change the
desired content and press
. Press under Save
set ringer ID Press under Contacts.
Select a contact and press
K
under Contacts.
/
>
You can store a phone number or private ID in
Contacts
:
r
K
.
Find it:
/
>
L
>
[New Contact]
K
1
Enter a name for the new entry. Each
entry’s name can contain 20 characters.
/
>
Edit [Ring Tone/Picture].
>
Select Ringer and chose your
desired ring tone. Press
under Done
2
3
Select a specific Ring Tone
.
K
Select a type for the entry (Mobile
,
Private1
,
.
Private2
Pager
choose Private1 Private2
,
Work1
,
Work2
,
Home
,
Email1
,
Email2 Fax,
,
,
IP or Other). To store a private ID
or
.
essentials
17
3
If you chose a phone number, press
,
to
feature
call the entry, or if you chose a Private ID,
press and hold the PTT button to call the
number.
set picture
ID
Press
K
under Contacts.
Select a contact and press
/
>
Edit
Select Picture and choose
your desired picture. Press
under Back under
Save
>
[Ring Tone/Picture].
finding your phone
number and private ID
K
>
K
.
Find it:
/
>
m
>
My Info.
call a stored phone
number or private ID
messaging
Your phone has the ability to use both
MOSMS and Multimedia Messaging Service
(MMS) messaging. The type of messaging
your phone uses will be determined by your
service provider. If your service provider offers
messaging through MOSMS, your phone
sends and receive messages using MOSMS.
Find it:
/
>
L.
1
2
Scroll to the Contacts entry.
If the Contacts entry contains more than
one number, scroll left or right until the
type of the number you want to call is
displayed (Mobile
,
Private1, Private2, Work1,
If your service provider offers MMS, your
phone sends and receives messages using
Work2 Home, etc.).
,
essentials
18
MMS. Additionally, MMS allows you to send
and receive messages that may include text,
pictures, videos, and audio files.
quick notes
When you are filling in the Message and Subject
fields, you can add ready-made words or short
phrases called Quick Notes. After you add
these words or phrases, you can edit them as
you would any other text.
create and send messages
1
From the home screen press
K
under
Mesgs
>
[Create Message].
1
While you are creating a message, scroll
to or select Message or Subject
2
Enter the phone number of the person
you want to send the message to and
.
2
3
Press K under QNotes.
press
r
or press
K
under Search. Select
Select the quick note you want to insert
into the message.
Contacts or Recent Calls to find the number you
want.
4
Press
K
under Send.
3
Select Message: and enter the text of the
message or to use a quick note press
K
under QNotes and scroll to the quick note
you want.
MMS features
Note: The following features are available only
when using MMS.
4
If you want to send the message, press
K
under Send or to delete the message
without sending it, press K under Cancel
.
essentials
19
more message options
To view more message fields in a message
insert a picture, video, and
audio recording
you are creating, select ....More....
You can insert one or more pictures, videos,
and audio files from the media center into the
body of the message. You can include text in
the body of your message in addition to these
items.
The following options become available:
option
Subject: Create or edit the subject line.
Attach: Attach a picture, audio file or voice
record.
insert items
While you are filling in the Message field, press
Cc: Send a copy of this message to
someone else.
/
, select Insert and choose from Insert Picture
Insert Audio Insert Video Capture Video, Capture Picture or
Record Voice
,
,
,
Auto Replies: Allows you to create a list of
possible short answers for the recipient to
choose when replying to your message.
.
A list of available pictures, videos, or audio
files appears. You can only insert one item at a
time.
Priority: Set priority Normal or High
Valid Until: Set a date after which attempts to
deliver the message end, or press
under No Date
.
Select the picture, video, or audio recording
you want to insert.
K
.
essentials
20
If you want to attach more items, select
remove an inserted item
To remove an item from the message you are
[New Attach]
.
3
When finished, press
K
under Done.
creating, highlight it and press
K
under Delete.
Note: You can only attach audio files and
pictures if they are not forward locked and if
their DRM settings do not prevent you from
sending.
attach a picture, video, or audio
recording
You can attach one or more pictures, audio or
voice recordings from your phone into the
body of the message. You can include text in
Forward locked items are usually copyright
protected, and you cannot share them with
anyone, such as in Private calls or by
uploading them from your phone.
the body of your message in addition to these
items.
1
While you are filling in the Attach field,
press [New Attach] > and select from Browse
take a new picture
Pictures
,
Capture Picture
,
Browse Audio
,
Record Voice
,
1
While you are creating a message, scroll
to any message field and press or
select Attach
Browse Video, or Record Video
.
/
>
[New Attach].
A list of available pictures, audio files, or
voice recordings appears.
2
Select Capture Picture. This accesses the
camera.
2
Select the picture, audio or voice record
you want to attach.
essentials
21
3
Take the picture. For instructions on how
to take the picture see “camera” on
3
To save the video, press
To discard the video without saving it,
press under Discard
r.
K
.
4
When you have captured the picture you
4
The video is attached to the message and
saved to the media center in the default
storage location.
want, press
To discard the picture, press
Discard. You can then take another picture.
When finished, press under Done
K
under Save.
K
under
create a new voice record
5
K
.
You can create a new voice record to send
with a message:
The picture is attached to the message
and saved to the default storage location.
1
2
3
Press
/
or select Attach
>
[New Attach].
record a video
You can record a video to send with a
message:
Select Record Voice
.
Say the message you want to record into
the microphone.
1
2
Select Attach
Record and adjust video.
To view the video without saving it, press
under Review
>
[New Attach] > Record Video.
4
When you are finished recording, press
r
.
5
When finished, press
K
under Done.
K
.
essentials
22
6
The voice record is attached to the
message and saved to the media center
and the list of voice records.
2
To edit the fields you want to change,
follow step 2 through step 4 in “create
and send messages” above.
remove an attachment
delete a draft
To remove an attachment in a message you
are creating:
When you send a draft, it is removed from the
Drafts folder.
1
2
Select Attach
.
1
To delete a message in the Drafts folder
without sending it, scroll to the message
Scroll to the attachment you want to
remove.
you want to delete and press
K
under
Delete
.
3
Press
/
>
Unattach.
2
Press
K
under Yes to confirm.
use drafts
When you save a message as a draft, it is
saved in the drafts folder.
inbox
Find it: Press
/
>
E
>
Inbox.
Find it: Press
/
>
E
>
Drafts.
receive a message
1
Select the draft you want to edit.
1
To view the message press
K
under Read
.
essentials
23
2
To dismiss the message notification press
under Exit
3
To reply to the message, press
Reply.
K
under
K
.
While reading a text and numeric message
that contains a phone number, you can press
delete unread messages
,
to call that number.
1
Scroll to the message you want to delete.
Press under Delete and under Yes to
confirm.
2
K
K
threaded inbox
The threaded Inbox allows you to organize
your messages by subject or sender.
forward a message
1
From the Message Center, Press
Threading, and select from None Subject, or
Sender
/
>
1
Press
/
>
Forward.
,
2
Create and send your message.
Embedded objects and attachments are
included when you forward a message.
.
Note: Threading by subject is dependant
upon your service provider.
lock and unlock messages
Locked messages cannot be deleted until you
unlock them.
read from the message center
1
From the home screen press
K
under
Mesgs
>
Inbox.
1
View the message you want to lock or
unlock.
2
Select the message you want to read.
essentials
24
2
Press
/
>
Lock Message or Unlock Message
.
From field, the To field, the Cc field, the Subject
field, or the body of the message, you can
call a number in a message
store this information to Contacts.
1
2
View the message.
If a message you receive contains a phone
number or Private ID in the From field, the To
field, the Cc field, the Subject field, or the body
of the message, you can call or send a call
alert to that number.
Highlight the number or email address
you want to save.
3
Press
To store the number or email address as a
new entry, select [New Contact]
/
>
Save Number or Save Email.
4
send a call alert
.
1
2
3
4
View the message.
To store the number or email address to
an existing entry, select the entry.
Highlight the Private ID you want to alert.
5
6
With the Contacts type field highlighted,
Press
/
>
Alert.
press
;
left or right to display the
Push the PTT button.
Contacts type you want to assign the
number or email address.
store message information to
contacts
Press
K
under Save.
If a message you receive contains a phone
number, Private ID, or an email address in the
reply to a message
To reply to a message:
essentials
25
1
2
View the message you want to reply to.
To reply to the sender only, press
under Reply or press under Reply All to
reply to all recipients.
go to a website
If a message contains one or more website
URLs, you can go to that website.
K
K
1
2
View the message.
3
A list of short phrases appears. Select any
of these phrases to add it to your
Highlight the website URL you want to go
to.
messages or select [Create Reply]
.
3
Press /> Go To Website.
4
Edit any message fields you want to
change.
Note: The entire URL must appear in the
message to allow you to open the website.
5
Press
K
under Send.
embedded objects and
attachments
If a message contains pictures, videos, or
audio files in the body of the message,
highlight each picture, video, or audio
recording to view or play it.
use auto replies
If the message you are replying to was sent
with auto replies, it contains a numbered list
of possible replies for you to send. Press the
number of the reply you want to send. The
reply is sent immediately without further
action.
If a message contains a picture, video, or
audio recording as an attachment, open the
essentials
26
attachment to view the picture or play the
video or audio recording.
2
Highlight the picture, video, or audio
recording you want to save.
3
Press
/.
open attachments
4
Select Save Picture Save Video, or Save Audio.
,
1
View the message.
The item will save in the default storage
location.
2
Highlight the attachment you want to
open. Attachments appear at the end of a
message.
delete an embedded picture,
video, or audio recording
3
Press
r.
Attachments of an unknown type cannot be
opened, but can be deleted.
To delete a picture, video, or audio recording
that is part of the body of a message you
receive:
save an embedded picture,
video, or audio recording
To save a picture, video, or audio recording
that is part of the body of a message you
receive:
1
2
View the message.
Highlight the picture, video, or audio
recording you want to delete and
press
/.
3
Select Delete Picture
,
Delete Video, or Delete Audio
.
1
View the message.
essentials
27
Find it: Press
/
>
E
>
Outbox.
save attachments
1
View the message.
resending failed messages
from the outbox
2
Highlight the attachment you want to
save.
1
Scroll to the message you want to resend
or press the number of the message you
want to resend.
3
Press
/
>
Save Attachment.
Selected items save to the default storage
location.
2
Press
K
under Resend.
delete attachments
cancel an unsent message
1
View the message.
1
Highlight the message you want to
cancel.
2
Highlight the attachment you want to
delete.
2
3
Press
Press
/.
3
Press
Press
/
>
Delete Attachment.
K
under Cancel.
4
K
under Yes to confirm.
sent items
The Sent Items box holds sent messages.
outbox
The Outbox holds all unsent messages.
essentials
28
delete all unlocked sent messages
forward items from sent items
1
Press
/
>
Delete All.
1
Scroll to the message you want to
forward.
2
Press
K
under Yes to confirm.
2
3
Press
Make edits if you wish, select the
recipient and press under Send
/
>
Forward.
customize messaging
K
.
Find it:
/
>
E
>
/
>
Setup.
This option is available from many
context-sensitive menus.
check delivery status
If a message was successfully sent and you
set the message to confirm delivery, you can
check the delivery status:
The following options become available:
option
1
2
Scroll to the message you want to view.
Press
Signature: Allows you to create a signature
that is automatically inserted at the end of
your messages. Signatures can be edited
before sending the message.
/
>
Delivery Status.
delete sent messages
Quick Notes: Lets you create new Quick Notes
and edit or delete Quick Notes you created.
1
2
3
Scroll to the message you want to delete.
Press
Press
K
K
under Delete
.
under Yes to confirm.
essentials
29
folder hold up to 30 messages each. If they
are full, you cannot receive messages, send
messages, or save drafts until you delete
some items.
option
Cleanup: Controls how long messages remain
in the Inbox and Sent Items before being
deleted.
Note: Media files and Java applications can
affect the available amount of memory on
your phone. If you run out of memory and
your Inbox, Sent Items, Outbox, and Drafts
folder are empty, delete unwanted media files
and Java applications to free up memory.
Delivery Rpt Default: Allows you to be
automatically notified when your message
is delivered.
Memory Size: Shows a report on used and free
memory in your phone.
MMS Setup: opens a submenu to set MMS
options.
To view the amount of memory available in
your text inbox:
Note: Available with MMS only.
Find it: Press
/
>
E
>
/
>
Setup
>
Text Msg Setup: opens a submenu to set text
messaging options.
Memory Size
.
MMS setup
Note: Available with MOSMS only.
Find it:
/
>
E
>
/
>
Setup
>
MMS Setup.
manage memory
This option is available from many
Your text Inbox and Sent Items hold 200
messages each. The Outbox, and Drafts
context-sensitive menus when you are using
MMS.
essentials
30
The following options become available:
This option is available from many
context-sensitive menus when you are using
MOSMS.
option
Friendly Name: Allows you to create a friendly
name. Your friendly name is displayed in the
From field on other iDEN handsets when
your message is received.
The following options become available:
option
Srvc Cntr No: Allows you to enter a service
Download Options: Controls whether your phone
downloads new messages. Set this option
to Automatic if you want your phone to
download new messages automatically.
Select Manual if you want your phone to
prompt you before downloading new
messages.
center number.
Expire After: Allows you to set the number of
days before a message expires.
new quick notes and reply
phrases
Replies: Lets you create or edit and delete
reply phrases you created.
create quick notes or replies
1
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies
.
text message setup
2
3
Select [New Quicknote], or [New Reply]
.
Find it:
/
>
E
>
/
>
Setup
>
Text Msg setup.
Enter text from the keypad and press
r.
essentials
31
edit quick notes or replies
You can edit only Quick Note phrases you
have created.
delete all quick notes or replies you
have created
1
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies
.
1
2
3
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies.
2
3
Press
Press
/
>
Delete All
.
Select the quick note or reply you want to
edit.
K
under Yes to confirm.
cleanup options
Edit the text and press
r.
The cleanup option controls how long
messages remain in the Inbox and Sent Items
before they are deleted. You set the cleanup
option for the Inbox and Sent Items
separately.
delete quick notes or replies you have
created
1
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies.
2
Scroll to the quick note you want to
delete.
The clean up option deletes only read,
unlocked messages and sent messages.
3
Press
Press
K
K
under Delete
.
Find it:
/
>
E
>
/
>
Setup
>
Cleanup.
4
under Yes to confirm.
1
Select Inbox or Sent Items
.
essentials
32
2
Choose a clean up option from the
following list:
option
FirstIn FirstOut: Messages are deleted as
option
necessary on a FirstIn FirstOut basis.
Off: Messages are never automatically
deleted.
Custom: Lets you create a clean-up option of
up to 199 messages or 99 days for the
Inbox and Sent Items.
5 Messages: If you have more than 5
messages, messages are deleted in the
order they were received, starting with the
oldest, until 5 are left.
3
Press
K
under Yes to automatically
delete messages now or press
K
under
No to delete messages later.
10 Messages: If you have more than 10
messages, messages are deleted in the
order they were received, starting with the
oldest, until 10 are left.
delete all messages
To delete all read, unlocked messages from
the Inbox, all messages in the Drafts folder, all
successfully sent messages in Sent Items, or
unsent messages in the Outbox:
1 Day Messages are deleted if they are older
:
than 1 day.
3 Days: Messages are deleted if they are
older than 3 days.
Find it:
/
>
E
.
1
2
Select Inbox
,
Drafts Sent Items, or Outbox.
,
With these options, messages are deleted
when you exit the message center after
setting the option.
Press Delete All.
/
>
essentials
33
3
Press
K
under Yes to confirm.
notification tone every 30 seconds until you
access the message or dismiss the alert.
delete a thread
To delete a thread from the Inbox:
If you are on a call when you receive a
message, your phone may sound a
notification tone during the call or after you
end the call, depending on how you set your
notification options.
1
2
3
From the Inbox, select a thread.
Press
Press
/
>
Delete Thread.
K
under Yes to confirm.
set notification options
message notifications
When you receive a message, your phone
notifies you with text on the display, a
notification tone or vibration.
To control whether your phone sounds
message notification tones while you are on a
phone call:
Find it:
/
>
u
>
Phone Calls> Notifications.
You can access the message or dismiss the
notification.
Select from the following options:
option
If you dismiss the notification, the message is
not deleted. It can be accessed through the
message center.
Receive All: Tones sound during calls for all
types of messages.
If you are not on a phone call when you
receive a message, your phone sounds a
essentials
34
option
Message Mail Only: Tones sound during calls for
mail messages; tones for all other types of
messages are held until you end calls.
Delay All: Tones for all types of messages are
held until you end calls.
Note: Delay All is the default setting.
To set notification options during a call press
/
>
Call Setup
>
Notifications.
essentials
35
basics
status indicators
Status indicators are shown at the top of the
home screen:
display
1 2
3
4
5
6
7
The home screen shows when you turn on
the phone. To dial a number from the home
screen, press number keys and
,.
Note: Your home screen may look different.
Ready
Time
5/10/09
Date
Contcs
Mesgs
1
Signal Strength Indicator: Vertical bars
show the strength of the network
Left
Right
Soft Key Label
Contcs
Mesgs
Soft Key Label
connection. You can’t make or receive
calls when
~
shows.
Soft key labels show the current soft key
basics
36
2
3
Active Phone Line:
line 1 is ready to make calls.
%
indicates phone
main menu
All your phone’s features can be accessed
through the main menu. You can set the main
Speaker On/Off: Sounds associated with
Private calls can be set to come through
the earpiece rather than through the
speaker.
menu to appear as List View
,
Tab View or Icon View
.
Find it: Display/Info
/
>
u
>
>
Menu View
.
4
5
6
Ringer Vibe/Off: Your phone is set to not
ring.
carousel menu
The Carousel Menu allows you to access up
to nine applications from your phone’s idle
screen.
Message Indicator: Shows when
you receive a text message.
Packet Data: Your handset is ready to
transfer packet data or is transferring
packet data when it shows a blinking
arrow.
accessing an application
1
Using the navigation key, scroll left or right
until you highlight the desired application.
7
Battery Charge Indicator: A fuller battery
indicates a greater charge. Recharge the
battery when your phone shows Low Battery
2
Press to launch the application.
r
.
Note: Availability of the Carousel Menu is
dependent on your service provider.
basics
37
auto hide
text entry
1
Press
Auto Hide
/
.
>
u
>
Personalize
>
Carousel
>
Your phone provides convenient ways to enter
words, letters, punctuation, and numbers
whenever you are prompted to enter text (for
example, when adding a Contacts entry or
when using Text Messaging).
2
Select from Off
,
2 seconds 4 seconds, or
,
8 seconds
.
Note: When Auto Hide is set to Off, the Carousel
Menu will always be visible on the idle
screen.
change the character input mode
1
When you see a screen where you can
enter text, press to change the
/
assigning applications
character input mode.
1
Press
/
>
u
>
Personalize
>
Carousel.
2
Select one of the following options:
2
Highlight the position on the Carousel
Menu you would like the application to
entry method
Alpha
Press a key several times for
occupy and press
r.
different characters.
3
Highlight an application and press
select it.
r
to
Word
Enter words using a predictive
text entering system that lets
you enter a word with fewer
keypresses.
basics
38
The Word English text input method
entry method
combines the groups of letters found on each
phone key with a fast-access dictionary of
words, and recognizes what you want to text
as you type. It first offers the most commonly-
used word for the key sequence you enter
and lets you access other choices with one or
Symbols
Numeric
Enter symbols.
Enter numbers by pressing the
numbers on the keypad.
Text Input Selects the desired entry
Settings
languages and Word Prediction
features.
more presses of the
0
key.
Insert
Selects a item to be inserted,
such a picture, an audio/video clip
or a voice recording.
enter a word using “word” method
character input
1
Select the Word character input method.
Note: available only when using
MMS messaging.
2
Press the corresponding keys once per
letter to enter a word (for example, to
enter the word Bill, press 2 4 5 5).
Tip: When entering text, press
letter capitalization (Abc
#to change
abc).
(If you make a mistake, press
a single character. Press and hold
delete an entire entry.)
*
to erase
to
>
ABC
>
*
word method
The Word English text input method lets you
enter text into your phone by pressing keys
just once per letter.
3
To accept a word and insert a space,
press
#
.
basics
39
To accept a word completion (such as
lowercased. After a character is entered, the
cursor automatically advances to the next
space after two seconds or when you enter a
character on a different key.
Billion when you entered Bill), press
right.
;
If you get a word you don’t want, you can
press the
0
key to see more word
Characters scroll in the following order:
choices and pick the one you want.
characters
1
Space . 1 ? ! , @ & : ; “ - ( ) ‘ ¿ ¡ %
£ $ ¥
alpha method
To enter characters by tapping the keypad:
2
3
4
5
6
7
8
9
0
#
A B C 2 Á Ã Â À Ç
D E F 3 É Ê È
G H I 4 Í Ì
1
Select the Alpha method.
2
Press the corresponding keys repeatedly
until the desired letter appears. (For
example, to enter the word Bill, press
twice, three times, three times,
and three times again. If you make a
2
J K L 5
4
5
M N ñ O 6 Ó Õ Ô Ò
P Q R S 7 ß
5
mistake, press Delete to erase a single
character. Press and hold Delete to erase an
entire word.)
T U V 8 Ú Ü Û Ù
W X Y Z 9
+ - 0 * / \ [ ] = > < # §
Space / Shift
By default, the first letter of an entry is
capitalized and the following letters are
basics
40
characters
volume
Press the volume keys up
or down to:
*
Back
When entering text, press and hold
#
to
•
•
•
turn off an incoming
call alert
switch between lowercase and uppercase
letters. The icons in the upper left-hand corner
of the screen show the character type.
change the earpiece
volume during calls
character type
change the ringer
volume from the
home screen
Q or T Lowercase
R or U Uppercase
S or V Shift Lock
Tip: You can quickly set your ringer to
Vibrate All by holding the down volume
key in the home screen.
W
Numerical
Symbols
X
basics
41
navigation key
transmitters
Press the navigation key
up, down, left, or right to
scroll to items in the
display. When you
Consult airline staff about the use of the
Transmitters Off feature during flight. Turn off
your phone whenever instructed to do so by
airline staff.
highlight the desired
Transmitters Off turns off your phone’s calling
and Bluetooth features in situations where
wireless phone use is prohibited, but you can
use the phone’s other non-calling features
when Transmitters is turned Off.
item, press
it.
r
to select
handsfree speaker
You can use your phone’s handsfree speaker
to make calls without holding the phone to
your ear.
Find it:
/
>
u
>
Advanced
>
Transmitters
>
Off.
During a call, press
K
under Speaker to turn
the handsfree speaker On.
The handsfree speaker stays on until you
press
K
under Speaker again.
basics
42
features for the hearing
impaired
using your phone with a
hearing aid
For best results use the following optimization
procedures and handset setting. They
generally apply as well for users with cochlear
implants:
If your HA has a telecoil, activate its switch,
then also rotate the handset as illustrated to
align the telecoils.
Note: Some automatically switched hearing
aids may need an auxiliary switching magnet.
optimize your handset position and
orientation
If you are unsure whether your HA is telecoil
equipped or needs an auxiliary magnet,
please refer to your HA user guide or contact
a hearing aid professional or supplier.
While in a phone call slide your phone up and
down, then left and right until best
microphone coupling is obtained. You also
may need to adjust your hearing aid (HA)
volume setting.
basics
43
Approximate telecoil location is within
6-13 mm of this location.
TTY
feature
Off - Shut off
M - Microphone
T - Telecoil
turn On TTY Press
feature
/
>
TTY
u
>
Phone Calls
>
>
Use TTY
>
On.
choose TTY Press
/
>
TTY
u
mode
Phone Calls
>
.
Approximate telecoil location is just
above the battery.
Select from TTY
,
VCO or HCO.
change the
TTY baud
rate
Press
Phone Calls
/
>
TTY
u
>
choose your hearing aid setting
Find it: Phone Calls Hearing Aid.
>
>
Baud.
/
>
u
>
>
Select 45.45 or 50.00
.
1
Set this option to Microphone. Microphone
coupling is now optimized.
change TTY While in the TTY call, press
mode
during a call
/
>
In Call Setup
>
TTY
>
Type.
or
Select from TTY
,
VCO or HCO.
2
Set this option to Telecoil. Handset meets
US federal requirements for telecoil
coupling sound or set this option to Off
(factory default). This is the setting for non
HA users.
Note: The TTY device must be connected to
the phone through the micro-USB port.
A 2.5 mm to micro USB adapter is required to
support TTY.
basics
44
lock and unlock keypad
security features
feature
When your phone is closed and on the home
screen, your keypad locks to prevent
accidental key presses.
phone lock
To lock the phone press
/
Phone Lock
Auto Lock
>
u
>
Security
>
To change how long your phone waits before
it automatically locks your keypad press
>
Lock Now or
/
>
.
u
>
Security
>
Keypad Lock
>
Auto Lock and select a
keypad lock To lock the keypad press
time interval or Off
To lock your phone’s keypad, close the slide,
or with the slide open, press /*
To unlock your keypad press under Unlock
and press under Yes
.
/
>
u
>
Security
>
Keypad Lock. Select Lock Now, or
.
select Auto Lock and select
K
,
from Off
,
2 seconds, 4 seconds, or
K
.
8 seconds
.
enable SIM Press
PIN
change SIM Press
PIN
/
>
.
u
>
Security
Security
>
SIM PIN
>
On
/
>
u
>
>
>
Change Passwords
SIM PIN.
Note: You can make emergency calls on a
basics
45
main attractions
•
My Images provides a slide show, image
browser and image editor.
multimedia
Your phone comes with several multimedia
applications to let you access pictures, videos,
and audio files stored in your phone’s memory
or in the Audio, Music, Podcast, Image and
Video folders on a memory card inserted in
your phone’s memory card slot:
•
•
•
•
My Videos plays video files on the display.
Camera lets you take still pictures.
Camcorder lets you take short movies.
Ringtones lets you purchase and preview
ringtones for your phone.
•
Media Center is a central repository to
view all supported multimedia files on
your device or your memory card.
•
VoiceRecord lets you record audio notes to
yourself.
In addition, the following audio files can be
accessed through the media center:
Note: The Media Center cannot read
the Music and Podcast folder from the
SD card.
•
•
VoiceRecords
•
My Music provides an enhanced music
player for music and podcast files.
Musical ring tones in the list of ring
tones
main attractions
46
•
•
Audio files saved from MMS messages
received
Media files supported by the Media Center
include:
Audio files downloaded to your phone
Format
Bit Rate / Info
Sampling
Rate
Because the memory card inserted in your
phone may contain files saved to it using a
device other than your phone, not all types of
pictures, videos, and audio files on the
memory card may be accessed through your
phone’s media center.
AAC
Up to 320kbps
48 kHz
(MPEG4
AAC-LC)
.aac* , .3gp,
.m4a, .3ga,
.mp4
AAC+
Up to 128 kbps
(16 to 128 kbps)
Max: 48
kHz
Items in the media center can be sent in
MMS messages and with Bluetooth. See
.aac*, m4a,
.3ga, .mp4
AAC+
Up to 320 kbps
(16 to 320 kbps)
Up to
48 kHz
Enhanced
.aac*, .m4a,
.3ga, .mp4
Pictures in the media center can be sent in
AMR-NB
.amr, .3gp,
.3ga, .mp4
4.75 kbps – 12.20 8 kHz
kbps (supports all
3GPP specified
rates)
main attractions
47
Format
Bit Rate / Info
Sampling
Rate
Format
Bit Rate / Info
Sampling
Rate
AMR-WB
.awb, .3ga,
.3gp
6.6 kbps - 23.85
Kbps(supportsall
3GPP specified
rates)
16 kHz
PCM 16-bit
Linear
Up to 1536 kbps
Up to 48
kHz (8,
11.05, 12,
16, 22, 24,
3, 44, 48
kHz)
.wav, .au
iMelody
.imy
1 – 3.5 kHz
Monophonic
N/A
N/A
PCM 8-bit
Linear
.wav, .au
Up to 1536kbps
Up to 704 kbps
Up to 704 kbps
Up to
48 kHz
MIDI XMF
.xmf, .mmf,
.xmf0, .xmf1,
.mxmf
64 channels
64 channels
Up to 320kbps
PCM 8-bit
A-law
.wav, .au
Up to
48 kHz
MIDI
N/A
Stand
.mid, .midi,
.smf
PCM 8-bit
mu-law
.wav, .au
Up to 44
kHz (8,
11.05, 12,
16, 22, 44
kHz)
MP3
Up to
48 kHz
.mp3*,
.mpga*
Real Audio
LBR (Cook)
.rm, .ra, ram
Up to 96 kbps
Up to
44.1 kHz (8,
11, 22, 44
kHz)
main attractions
48
Supported video file formats include:
Format
Bit Rate / Info
Sampling
Rate
Format
Resolution / Extension
Real Audio
Sipro
5 kbps (fixed
rate)
8 kHz
Bit and
Frame Rate
(ACELP®.net)
.rm, .ra, ram
8.5/6.5 kbps (dual 8 kHz
rate)
MPEG4 +
352 x 288
.mp4, .3gp
AMR-NB
and 320 x
240 (up to
MPEG4 +
AMR-WB
16 kpbs (wide
band)
16 kHz
256 kbps);
176 x 144 and
128 x 96 (up
to 128 kbps);
up to 30 fps
MPEG4 + AAC /
AAC+ /Enhanced
AAC+
Real
Audio 10
.rm, .ra, ram
Up to 192 kbps
Up to 320 kbps
Up to
48 kHz (8,
11, 12, 16,
22.05, 24,
32, 44.1, 48
kHz)
H.263 + AMR-NB
H.263 + AMR-WB
352 x 288 (up .3gp
to 256 kbps);
176 x 144 and
128 x 96 (up
to 64 kbps);
15 fps
H.263 + AAC /
AAC+ /Enhanced
AAC+
WMA v9 L2
(also WMA
v3, v7, v8)
.wma*
48 kHz
Real Video G2 / 8 Up to 320
.rm, .rmvb
/ 9
kbps, 320 x
240, 15 fps
(*) These formats support album art and lyrics.
main attractions
49
The music player will display the name of the
song playing and the artist.
Format
Resolution / Extension
Bit and
Frame Rate
Now Playing...
H.264
Up to 320
kbps, 320 x
240, 15 fps
.mp4, .3gp
.wmv, .asf
The Song
The Band
WMV8 / WMV 9
Up to 384
kbps, 320 x
240, 24 fps
0:39
3:38
Pause
Back
my music
The music player groups the music files into
folders and lists. When you select a music file
to play, the music player plays this file, then
plays the other music files grouped with it.
Your handset includes a music player that you
can use to play music files stored in the
phone memory and the MUSIC/AUDIO/
PODCAST directories on the memory card
inserted in your phone.
The music player also plays podcasts you
download to your computer and then save on
the Podcast directory on your phone’s
memory card. You can mark highlights within
a podcast file to help you find the parts you
most want to listen to.
main attractions
50
Connect your phone to your computer using a
compatible USB cable. (Wait for the
connection to be completed. When
connected, the host computer will
automatically detect your phone.)
the Music folder, Podcasts to the Podcast folder
and videos to the Video folder.
filename rules
When naming files stored on the memory
card, the following rules apply:
If your service provider offers MMS, you can
send details of the podcast to a friend and
send feedback to the podcast creator using
MMS messages.
•
The filename can contain UTF8
characters, including ASCII, however
only supported characters will be
displayed.
understanding the memory
card folder structure
When you first insert the memory card into
•
The filename can be up to 255
characters long, including the file
extension, however only the first 32
characters will be displayed.
your phone, five folders are created: Audio
,
Warning: If a music file name is longer than
255 characters, including the file format
(.MP3), the song will not be visible on the
player and therefore can not be played. This
can be corrected by renaming the file and
replacing it on the card.
Image Music,
,
Podcast, and Video. In order to view
files stored on the memory card, you must
store the given file in its corresponding format
folder: audio files such as ring tones, and
voice recordings to the Audio folder, pictures to
the Image folder, music files such as songs to
main attractions
51
contents of that folder or press
the contents of the folder.
r
to view
play music files
Find it:
/
>
j
>
My Music or press
[.
To stop viewing a folder and return to the
folder or list that contains it, press under
Note: The i856w does not have a Music Key
and a Play Key.
K
Back
.
1
Scroll to choose how you want your music
played (Songs, Playlists, Albums, etc.).
play music while loading files
Tip: The Songs folder contains all the
music files on the memory card in a single
list.
The first time the music player finds music
files on your memory card, it loads and
organizes these files. This may take a long
time for a large number of files.
2
To play the first music file in the folder,
press
K
under Play. (If the selected folder
To play music while files are loading:
contains subfolders, this plays the first
music file in the first of the subfolders.)
Find it:
/
>
j
>
My Music.
1
Scroll through songs and folders while
loading is going on the background.
Press
Scroll to a music file and press
Play or to play the first music file in it.
r
to view the folder’s contents.
K
under
2
Scroll to a music file or folder and press
y
K
under Play.
Any time you are viewing a list of folders with
the music player, you can scroll to a folder and
press
K
under Play to start playing the
main attractions
52
The following options become available
through the navigation panel:
set up the music player
Find it:
/
>
j
>
My Music
>
/
>
Setup
option
The music player can be set up with the
Pause and Resume: Press
pause, and press
K
under Pause or
y
to
following options by pressing
/
>
Setup:
K
under Play or to
y
option
resume playing paused music files.
Shuffle: Lets you set the music player to play
the music files in a list or folder in random
order.
Skip to Next or Previous: Press and release
right or left to skip to the next or previous
music file.
;
Repeat: Lets you set the music player to play
one or all the music files in a list or folder
repeatedly.
Fast Forward and Rewind: Press and hold
or left for 2 seconds to fast forward or to
rewind.
;
right
Visuals: Lets you choose among different
types of visual equalizers which sync with
the Music.
3D Music: Lets you experience surround
effects when the handset is tethered
to a stereo headset.
Setting the 3D Music feature to On, allows you
to select effects from the list of Music Reverbs
.
main attractions
53
Playlists enable you to organize music files,
but they do not change anything in other
folders or on the memory card. Adding or
deleting a file on a playlist does not copy,
delete or move it.
option
Album View: Lets you choose to view either a
list view or an image view.
Auto Update: Lets you reload all music files
every time you launch My Music. If you set
Auto Update to Off, it will follow the last known
music library configuration in order to save
loading time.
create a playlist
Find it:
[Create New]
/
.
>
j
>
My Music
>
Playlists
>
Equalizer: Lets you customize the sound of the
music player.
1
Enter a playlist name.
Note: If you do not assign a name, the
playlist is named Playlist followed by a
number. For example, the first playlist you
create without naming is automatically
View: Lets you choose between Default view
and Folder view.
Music Reverbs: Lets you choose a 3D sound
effect for use with the 3D Music feature.
named Playlist-1
.
2
Select [Add Songs]. A list of all music files
appears.
work with playlists
Playlists are lists of music files you create
from the files already available through My
Music.
Tip: For options to help you sort through
this list, press
/.
main attractions
54
3
Select each file you want on the playlist. A
checkmark appears by each selected file.
option
Remove Songs: You can remove some or all
songs while creating or editing a playlist.
Tip: To deselect a selected item, scroll to
a selected file and press
When you are finished selecting files,
press under Done and under Save
The following options are available for existing
playlists by pressing
r.
Before you have saved a new playlist or
while editing a playlist, scroll to the song
you want to remove and press
Remove Song and press
Remove All Songs. Press
4
K
K
.
/
>
r
K
, or you can select
under Yes to
/
>
My Music> Playlists >
confirm and
Reorder Playlists: You can change the order of
the playlists in the Playlists folder. Press
Reorder Playlists. Scroll to the
playlist you want to move and press
under Grab, and then scroll to the place
where you want the playlist to appear and
press under Insert
Delete a Playlist: While in the music player
select Playlists. Scroll to the playlist you want
to delete and press Delete Playlist. Press
under Yes to confirm.
K
under Save.
/
>
Edit Playlist:
option
/
>
Reorder Songs in a Playlist: You can change the
order of the music files while creating or
editing the playlist by pressing
Reorder Songs. Scroll to the song you want to
move, press under Grab, and then scroll
to the place where you want the song to
appear and press under Insert
Edit playlist
>
K
/
>
K
K
.
K
.
/
>
K
main attractions
55
Find it:
Select the song you want to add to your
favorites and press
/
>
j
>
My Music
>
Songs.
option
Edit a Playlist: You can change a playlist name,
add music files, remove music files, and
change the order of the music files. Select a
playlist and press
changes and press
Delete all Playlists: While in the music player
select Playlists. Press Delete All Playlists
and press under Yes to confirm.
/
>
Add To Favorites.
work with podcasts
/
K
>
Edit Playlist. Make
under Save
.
Find it:
/
>
j
>
My Music
>
Podcasts.
Note: The Podcasts folder is empty until you
download podcasts from your computer.
/
>
K
1
Scroll to view individual podcast episodes
or folders containing multiple episodes of
the same program.
Note: This deletes all playlists except the
Favorites playlist.
Reload Music: Searches your memory card for
music files.
2
Press
r
to view the podcast episodes
within a folder or the details screen of an
individual podcast episode.
use the favorites playlist
You can pause, resume, fast-forward, and
rewind just as with any other music file.
The Favorites playlist is a permanent playlist. You
can Add To Favorites, remove and change the
order of the music files, but you cannot
rename or delete music files.
Some functions differ when playing a podcast:
•
Pressing
y
when you have scrolled to
a podcast displays a screen showing
main attractions
56
podcast details, but does not play the
podcast. To play the podcast, press
under Play. After you begin playing the
add a highlight marker
K
1
While playing a Podcast press
/
>
Add Highlights
.
podcast, pressing
y
pauses and
2
3
Press
K
under On to mark the beginning.
resumes the podcast.
Go to the point in the podcast that you
want to mark as the end of the highlight
and press
•
If the podcast you are playing contains
highlights, pressing and releasing the
K
under Off.
;
right or left skips to the next or
previous highlight within the podcast,
or to the beginning or end of the
podcast.
4
Press K under Back.
Tip: Highlight markers can be deleted by
pressing Clear or pressing
Clear All Highlights from the
/
>
/
>
Edit Highlights
>
/
>
highlights
Podcasts menu.
Highlights are portions of a podcast that are
marked to help you find them more easily. You
can use the music player to add and delete
highlight markers. Press and release (don’t
send podcast information
You can only share podcast details with
others. If you want to share podcast details,
you have saved to your memory card, you can
send it in an MMS message that can be saved
and downloaded onto their computer.
hold) the
;
right or left to find them.
You can play all the highlights in a podcast and
skip everything that is not marked as a
highlight using Highlights Only
.
main attractions
57
Find it:
Forward Details
/
>
>
j
>
Send.
My Music
>
Podcasts
>
/
>
The music player continues playing and the
handset returns to the home screen. To jump
back to the music player, press
K
under Player.
background music
Your handset has the capability to play music
in the background while you are accessing
my images
My Images lets you easily browse, edit and
view a slide show of images on your phone or
memory card on your display.
other features like Settings
GPS Contacts MMS Datebook
,
Media Center
,
Bluetooth,
,
,
,
,
Memo Recent Calls, and
,
others.
You can also enjoy listening to your favorite
background music while browsing the web,
reading news or checking the weather.
my images menu
The My Images menu has many photo
management features. The following options
are available for images by pressing
play music in the background
/
>
j
>
/> and choose one of the following:
Find it:
/
>
j
>
My Music
>
Songs
.
1
Select a music file and press
the song.
y
to play
option
Edit: Displays several options for editing your
photos including:Crop, Rotate/Flip, Color Adjustment,
Resize, Borders, Stamps, Text and Text Bubble.
2
Press
/
>
Hide Player.
main attractions
58
option
option
Slideshow: Starts a slide show containing
images from the currently highlighted
image.
Set As Caller ID: Allows you to assign the
highlighted image to a Contact.
viewing images
Save as New: Lets you save an image with a
new filename.
Find it:
/
>
j
>
My Images
Slideshow to view a show of all
images in the current folder.
Press left or right to switch between
viewing images on the phone and the
memory card. The and keys can
also be used to scroll the images.
.
Preview: Displays the highlighted image.
1
2
Press
/
>
Send Via BLuetooth: Lets you send the image via
Bluetooth.
;
Rename: Lets you rename the image
filename.
#
*
Delete Current: Deletes the current highlighted
image.
Delete Multiple: Lets you chose multiple images
to delete at one time.
my videos
My Videos lets you easily browse and view
video files on your phone or memory card.
Switch to Card: Toggles between images stored
on the phone or memory card.
Find it:
/
>
j
>
My Videos.
Set as Wallpaper: Sets the highlighted image as
the device wallpaper.
main attractions
59
viewing videos
My Videos will display the video in portrait
mode by default.
camera
You can save pictures taken with the
integrated camera in your phone’s memory,
and can access them through the Media
Center.
Tip: To change the default to landscape mode
press
/
>
Full Screen.
Pictures you take can be sent via Private Calls,
Bluetooth, or MMS message. You can also
set them as your phone’s wallpaper.
my videos setup menu
Find it:
/
>
j
>
My Videos
>
/
>
Setup
Note: The Camera function is available only
when the slide is open.
The My Videos Setup Menu allows you to
change the following settings:
option
access the camera
To access the camera, press
View: Displays options for viewing your
videos as Default and Folder view.
/
>
j
>
Camera
.
3D Audio: Lets you turn 3D audio On and Off
.
To take pictures aim the camera lens and
press under Capture or press
Reverbs: Lets you choose from a number of
3D audio visual settings.
K
r.
To save the picture, press
To discard the picture without saving it, press
under Discard
r.
K
.
main attractions
60
From the camera viewfinder, you can press
to enter Menu Options
option
/
.
GPS Tag: Allows you to turn GPS Tag feature On
The following options become available:
of Off
Picture Quality: Adjust the picture quality to
Normal or Fine
Picture Size: Set up the picture size to Max
(1024x1280) XL (480x640) L (240x320) M (120x160),
.
option
.
Media Center: Opens the Media Center
application.
,
,
,
Record Video: To switch the camera to
camcorder mode.
S (96x128), or Wallpaper (176x220). You can also
set picture size from the viewfinder by
pressing
Zoom: To set the camera’s zoom to 1x 2x, or
,
left and right.
4x
.
White Balance: Sets the white balance to
Automatic
Night.
Remove Card: To safely remove the memory
card from the phone.
,
Sunny, Cloudy, Fluorescent, Tungsten or
Self Timer: Delay capturing the picture for a
selected number of seconds. The values
Exposure Control: Adjusts the exposure of the
picture from -2 to +2.
are: Off (default), 10 seconds
,
15 seconds, 20
Style: Sets the type of picture effect to Normal
Black and White
,
seconds
.
,
Sepia, Solarization and Negative.
To turn off the timer before the picture is
captured, press under Cancel
Memory Usage: Shows the total amount of Used
Free, and total Capacity of the phone’s memory
,
K
.
and of the SD memory card.
main attractions
61
The following options become available:
option
Memory Card: Allows you to remove the
option
memory card, set where videos are stored:
On Phone or Prefer On Card, format the memory
Ask for Name: If this option is On, you are
prompted to enter a name for each picture
before saving. Otherwise, pictures are
automatically saved with the date and a
number as their names.
card, and to display Help
.
Camera Setup: To access the camera set up
screen.
Shutter Sound
:
Set the default sound the
camera makes when is taking a picture.
Sets the default value for the Picture
access the media center
You can access the media center from the
Default Size
:
Size option.
camera at any time by pressing
/
>
Media
Center, except when you are using the Camera
Setup menu or viewing the memory screen.
Default Quality: Sets the default value for the
quality of the picture.
The media center contains all your pictures,
music files, and videos located on your
GPS Tag : If this option is On, pictures will be
tagged with the geographic location of
where they were taken.
phone’s memory. Press
your results.
*
and
#
to filter
customize the camera
Find it:
/
>
j
>
Camera
>
/
>
Camera Setup
main attractions
62
The following options become available:
camcorder
You can use your phone’s camcorder feature
to record videos.
option
Media Center: Opens the Media Center
application.
Find it:
/
>
j
>
Camcorder
Capture Picture: To switch the camera to picture
mode.
record video
Zoom: To set the camera’s zoom to 1x 2x, or
,
1
Press
To stop recording and discard the partially
recorded video, press under Cancel
To stop recording the video press
under Stop
To save the recorded video, press
K
under Record, or press
r.
4x
.
2
Remove Card: To safely remove the memory
card from the phone.
K
.
3
K
Video Size: Set up the picture size to Min
.
(128x96) Med (176x144), or Max (352x288). You
,
can also set picture size from the viewfinder
4
r.
by pressing
left and right.
Note: The Camcorder function is available
only when the slide is open.
From the camcorder viewfinder, you can
press
/
to enter Menu Options.
main attractions
63
customize the camcorder
option
Video Length: Allows you to choose between
Short, to limit video length for sending via
MMS message, or Maximum for longer
videos.
Find it:
/
>
j
>
Camcorder
>
/
>
Camera Setup
The following options become available:
option
Ask for Name: If this option is On, you are
prompted to enter a name for each picture
before saving. Otherwise, pictures are
automatically saved with the date and a
number as their names.
Note: When set to Maximum, video length is
limited to 60 seconds when stored to your
phone’s memory. When stored to a
memory card, video length is limited to
available space on the memory card, or two
hours.
Shutter Sound
:
Set the default sound the
camera makes when is taking a picture.
Sets the default value for the
Memory Usage: Shows the total amount of Used
,
Free, and total Capacity of the phone’s memory
and of the memory card.
Default Video Size
:
Video Size option.
Memory Card: Allows you to remove the
memory card, set where videos are stored:
On Phone or Prefer On Card, format the memory
deleting a recorded video
If you do not want to save the recorded video,
card, and to display Help
.
press
K
under Discard to delete the recorded
Camera Setup: To access the camera set up
screen.
video and return to the video viewfinder.
main attractions
64
•
•
•
•
•
Pictures1
sending video via MMS
message
To send the recorded video via an MMS
Datebook events
My Info
message, press
K
under Send. The video will
Contact information
Location information1
be automatically attached to a new MMS
message.
You can choose to send messages, pictures,
events, My Info Contacts or Location information to
the Private ID you are engaged in a Private call
Note: To ensure the video file is small enough
to be sent via MMS, set the Camcorder video
,
length to Short
.
with, Private IDs on the Recent Calls list, and
Private IDs stored in Contacts
.
PTX features
When you make or receive a Private call, your
phone automatically determines whether the
phone you are engaged in a Private call with is
able to receive each of these items. Your
phone saves this information for as long as
the Private ID is on your Recent Calls list or is
saved in your Contacts. Your phone updates the
saved information each time you make or
receive a call to or from that Private ID.
With Push To View features, your phone can
send and receive the following items through
Private calls with other phones that have this
capability:
•
Short text messages1
1. Additional charges may apply.
main attractions
65
are prompted to respond. Press
to acknowledge the message.
K
under Yes
send messages
The Push to Send Messages feature
lets you send short text messages through
Private calls.
begin a message from the Contacts or
the Recent Calls list
1
From the Contacts or the Recent Calls list,
select the entry containing the Private ID
you want to send the message to.
When you send a message, it appears on the
display of the phone you are engaged in the
Private call with.
2
Press
/
>
Use PTT Feature
>
Send Message.
begin a message and choose a
recipient
You can begin a message during a Private call,
begin a message from the PT Manager
The PT Manager lets you select the Private ID
you want to send the message to from Contacts
or the Recent Calls list.
from the Contacts list, the Recent Calls list, or from
the PT Manager
begin a message during a Private call
While in a Private call, press
.
Find it:
/
>
N
>
PT Manager
>
Send Message.
Then select A Contact or A Recent Call to see a list
of entries from the Contacts or the Recent Calls list
that can receive messages.
/
>
Use PTT Feature
>
Send Message.
Note: The first time you send a message,
Messaging Fees May Apply Continue? appears and you
main attractions
66
To view the message: Press
K
under Read
.
create messages
To dismiss the message: Press
K
under
After you have begun a message and chosen
a recipient, a screen appears that lets you
create the text of the message you want to
send. Your message may be up to 400
characters long.
Dismiss
.
reply to a message
1
2
3
View the message.
Press under Reply
You can choose from a list of ready-made
words or short phrases called Quick Notes.
You can use a Quick Note as it is or edit it
before you send it. Editing a Quick Note
changes the Quick Note for this message only
and will not change the Quick Note on the list.
K
.
Create the message and press the PTT
button to send it.
send pictures
You can send pictures stored in the Media
Center through Private calls. The picture you
send appears on the Private call recipient’s
display.
send a completed message
After you have completed your message,
press the PTT button to send it.
If the recipient accepts the picture, their
phone saves the picture. The picture then
appears in that phone’s recent call list.
receive messages
When you receive a message, a message
notification appears on the display.
main attractions
67
The first time you send a stored picture after
turning the phone on, Picture Fees May Apply
Continue? appears and you are prompted to
respond.
5
When prompted, press the PTT button to
resume the Private call.
start a call by sending a picture
Note: You cannot make or receive Private
calls while transmitting or receiving a picture.
from the media center
Find it:
/
>
j
>
Media Center
Scroll left or right to Media: Pictures
Select the picture you want to send.
Press
1
2
3
4
.
send a picture during a call
1
While in a Private call, press
K
under
>
Picture or press
/
>
Use PTT Feature
/
>
Send Via...
>
Send Via PTT
.
Send Picture.
Select A Contact or A Recent Call.
A list of pictures that can be included in a
Private call appears.
A list of contacts that have Private IDs and
are able to receive pictures appears.
2
3
4
Select the picture you want to send.
5
Select the name of the person you want
to send the picture to.
Press the PTT button to send the picture.
Wait while the picture is transmitted. The
Private call is temporarily interrupted
while a picture is transmitted.
6
7
Press the PTT button to send the picture.
When prompted, press the PTT button to
resume the Private call.
main attractions
68
from the PT Manager:
Find it: PT Manager
Select A Contact or A Recent Call.
Pictures you receive are saved either to your
phone’s memory or SD card. They are
accessible through the media center.
/
>
S
>
>
Send Picture.
1
When you see a message asking if you want
to accept the picture, press Yes to accept or No
to decline.
A list of contacts that have Private IDs and
are able to receive pictures appears.
2
Select the name of the person you want
to send the picture to.
clear a picture from the display
3
4
5
Select Browse Picture or Capture Picture.
If you want to clear a picture from your
phone’s display while still on a call, press
Press the PTT button to send the picture.
/
>
Clear Screen.
Once picture has been sent, when
prompted press the PTT button to resume
the call.
send a datebook event
to send a datebook event during a
private call
receive a picture
1
While in a Private call press
/
>
When someone sends you a picture, your
phone emits a tone or vibrates and a message
appears asking if you want to accept the
picture.
Use PTT Feature
>
Send Event.
Note: If these options do not appear on
the menu, the Private ID you are engaged
main attractions
69
in a private call with is not able to receive
Datebook events.
chose a recipient from Contacts, Recent
Calls or Memo, and press
PTT button to send.
r. Push the
2
3
4
If you want to create a new datebook
event, press
K
under New and create the
set my info sending option
event in your datebook. If you want to
chose an existing event do so.
You can control what portion of the
information in My Info is sent and whether it is
sent automatically in every call or only when
you choose to send it.
If the event is a recurring event: Select
This Event Only to send only the event
selected. Select Repeat Events to send all
occurrences of the event.
Find it:
PTT My Info
/
>
>
S
>
PT Manager
>
Configure
>
Info to Send
Push the PTT button to send the event.
1
Select or remove the fields you want to
send.
send my info
2
Press
K
under Done.
1
While in a Private Call press
/
>
The information your phone sends always
includes My Name, and Private ID1. You may also
Send My Info via PTT., and push the PTT button
to send.
send Line 1
,
Carrier IP, and Private ID2 depending on
or
your sending options.
2
From the home screen press
Send My Info via PTT. Enter a
Private ID or press under Browse to
/
>
C
>
My Info
>
/
>
K
main attractions
70
automatic sending
To control whether you send your information
automatically:
3
Push the PTT button to send.
or
1
2
From the home screen press
/
>
S
>
Find it:
PTT My Info
/
>
>
S
>
PT Manager
>
Configure
>
PT Manager
>
Send Contact.
Auto Send
Enter the Private ID number of the person
you want to send the Contact information
1
2
Select On or Off
to or press
K
under Browse
.
When you make a call in which your
information is sent automatically, the
name you entered in the My Name field of
My Info appears on the display of the
recipient’s phone, even if your name and
Private ID are not stored in the recipient’s
Contacts.
3
Select from Recent Calls
,
Contacts, or Memo.
Select the contact information you want to
send and push the PTT button.
send your location
You can transfer your approximate
location information through Private calls to
other enabled phones. Using the integrated
GPS feature, the following location
information can be shared:
send contact information
1
While in a Private Call press
/
>
Use PTT Feature
.
2
Select Send Contact and select the contact
information you want to send.
•
Time Stamped Latitude/Longitude
main attractions
71
•
Relative Location or Direction and
distance from the sender in Miles or
Kilometers
You cannot turn your phone’s ability to send
and receive My Info and contact information
on and off.
Find it:
/
>
S
>
PT Manager
>
Send Location.
Find it:
/
>
S
>
PTT Options On/Off PTT Features.
>
1
Select A Contact or A Recent Call.
1
Check or uncheck Messages, Pictures,
Events or Location.
A list of contacts that have Private IDs and
are able to receive locations appears.
one touch PTT
2
3
Select the name of the person you want
to send your location to.
Find it:
/
>
S
>
PTT Options One Touch PTT.
>
Press the PTT button to send your
location.
One Touch PTT sets your phone to do any of
the following each time you press the PTT
button from the home screen:
Note: The location information can be stored
in the recipient’s recent call list.
option
Off: Nothing happens when you press the
PTT button from the home screen.
turn PTT features on and off
You can turn your phone’s ability to send and
receive messages, pictures, and Datebook
events and location info on and off.
main attractions
72
option
option
Last Call: Call the most recent Private ID or
Group on the recent calls list.
Send Contact: Go to the first screen to send a
contact. See “send contact information” on
Assigned Number: Call a Private ID you assign.
Enter the number using your keypad, or
Send Location: Go to the first screen to send
your location. See “send your location” on
press
K
under Search. Select Contacts
.
,
Recent
Calls, or Memo
quick PTT
Send Message: Go to the first screen to send a
message.
Quick PTT lets you quickly make a call,
when accessing any Private IDs on your
phone.
Send Picture: Go to the first screen to send
To view a list of Contacts a with Private IDs in
Contacts
:
Send Event: Go to the first screen to send a
Datebook event.
Find it:
To move between Contacts
use the left or right, or press
To make a Private call:
Select the entries you want.
main attractions
/
>
S
>
Quick PTT
Send My Info: Go to the first screen to send My
,
Recent Calls, or Memo
,
;
*
or
#.
1
73
Bluetooth®
2
3
Press
K
under Done.
Push the PTT button.
Find it:
/
>
c
PT manager
The PT Manager lets you quickly access PTT
features, and other Private call features, from
the main menu.
turn Bluetooth on or off
You can turn your phone’s Bluetooth feature
on or off. While Bluetooth power is on, your
phone can communicate with other devices.
Find it:
/
>
C
>c
>
Setup Power
>
Find it:
/
>
S
>
PT Manager
1
2
Select On to power Bluetooth On.
1
Select Quick PTT Send Picture
,
Send Message
,
,
Send
Event Send My Info Send Contact, Send Location, or
,
,
Select Name if you wish to assign a name
to your handset.
Configure. After choosing what PTT item you
are sending, select a contact and press
the PTT button to send.
3
Select Find Me Duration to determine the
amount of time in which your handset can
be found by other Bluetooth devices.
or
2
Select Configure to configure your PTT Quick
You can turn off Bluetooth if you want to
prolong battery life or if you enter an area
where Bluetooth is prohibited.
Notes
,
PTT My Info, PTT Location, One Touch PTT, or
On/Off PTT Features
.
main attractions
74
Some Bluetooth devices ship with
Bluetooth PINs. Please refer to your
Bluetooth device’s user guide to locate
this information.
make a Bluetooth connection
connect your handset with a Bluetooth
headset
Find it:
[Look for Devices]
/
>
C
>
c
>
Audio Devices>
If a device ships without a Bluetooth PIN,
then you can enter any PIN for that
device. To establish a connection to that
device, enter the same PIN for both your
phone and the device. For example, if you
enter 1234 as the device’s PIN, then enter
1234 as your phone’s PIN.
1
Follow the instructions on your Bluetooth
headset to set it up to be found.
2
Once your Bluetooth headset is set to be
found press
phone will scan for the Bluetooth headset
until it finds it. Press when you see
r
on your handset. Your
5
Press
K
under Ok.
r
the name of the Bluetooth headset on
your screen.
This handset offers the Bluetooth auto pair
feature with auto pair compatible Motorola
devices. When bonded via Bluetooth with a
certain device, the pin will not be required
3
Your handset requires that you create a
bond in order to connect with a Bluetooth
headset. Press
K
under Yes when you
connect your handset with another
Bluetooth device
are prompted to bond with the headset.
4
Enter the Bluetooth pass key.
Find it:
/
>
C
>
c
>
Pair to Devices
main attractions
75
1
2
Select the device you want from the list of
found devices on your screen.
send information via Bluetooth
Your handset can transfer Contacts entries,
Datebook events, audio files, pictures and
videos to another Bluetooth device.
Create a bond if you are prompted to do
so.
If you have previously connected to a device,
the device will be stored on your phone so
you can connect with it easily.
The receiving device must be within 32 feet
(10 meters) of your phone in order to connect.
Note: Files sent or received may be up
to 10 MB, depending on your service
provider. File transfers will not work if a
microSD card is not installed in your phone.
use Bluetooth during a call
You can connect with available Bluetooth
devices during a call.
sending information
1
2
While in a call, press
/
>
Use Bluetooth.
1
From within Contacts, Datebook, or Media Center,
Select the audio device you want to
connect to from the list of Audio Devices
select the Contacts entry, Datebook
event, audio file, video, or picture you
want to send.
.
If the Audio Devices list contains only one device,
your phone will try to connect to it.
2
3
Press
/
>
Send Via...
>
Bluetooth.
Select the device you want to transfer the
contact information to, or search for the
device by selecting [Look for Devices]
.
main attractions
76
4
If prompted, bond with the device.
3
Double click on FIle Transfer Service.
Your phone connects with the devices and
transfers the information.
4
Drag and drop the files to the appropriate
folder.1 See “understanding the memory
how to check if your PC
supports Bluetooth FTP
Note: This process may be different
depending on the PC manufacturer.
1
Right click on the Bluetooth icon in the
system tray and open Bluetooth
configuration.
2
Click on the Client Applications tab and
check that File Transfer is active.
Note: This process may be different
depending on the PC manufacturer.
file browsing with the
Bluetooth file transfer service
1. If a music file is not visible in My Music, press
/
>
1
2
Double click the My Computer Icon on the
desktop.
Reload Music while in the music player application. All
music files within the Music folder on your microSD
card will be loaded into My Music.
Double click on My Bluetooth Places.
main attractions
77
call features
•
•
pictures sent or received
Datebook events received
turn off a call alert
You can press the volume keys to turn off a
call alert before answering the call.
The recent calls list displays up to 20 of the
most recent calls and call alerts.
1
Press
screen, briefly press
Calls.
/
>
Recent Calls or from the idle
recent calls
The recent calls list contains information
associated with calls you have made and
received and call alerts you have received.
,
to access Recent
2
3
Scroll through the list.
To view more details of the item
press
When you send or receive Private calls, the
recent call list contains the following PTX
items with those calls:
r
.
store an item to contacts from
recent calls
Phone calls, Private calls, My Info, Contacts or
Location entries received from other phones
•
•
•
contact information received
My Info received
short text messages received
call features
78
can be stored to the Contacts list from the
Recent Calls list.
caller ID
Caller ID allows people to identify a caller
before answering the phone by displaying the
number of the incoming call. If you do not
want your number displayed when you make
a call, just follow these easy steps.
Find it:
/
>
Recent Calls.
1
Scroll to or select the item you want to
store.
2
Press
K
under Save to store the
information as a new entry in the
Contacts list.
To block your phone number from being
displayed for a specific outgoing call:
or
1
2
3
Press * 6 7
Enter the number you want to call.
Press
.
3
Select an existing contact and update the
information.
,
.
4
Press
K
under Save to save your changes.
To permanently block your number, call your
customer service provider.
redial
call forward
Call forwarding sends calls to the phone
numbers you specify. You can forward all calls
to one number or forward missed calls to
To redial your last outgoing call, press and
hold . If your last outgoing call was a
,
Private Call, push the PTT button to initiate a
new Private call.
call features
79
different numbers depending on the reason
you missed the call. You can forward phone
lines 1 and 2 independently.
voice names
You can place calls by speaking commands to
your phone if you have previously assigned a
voice name to your contacts.
Find it:
/
u
>
Phone Calls
>
Call Forward.
1
To forward all calls select All Calls and select
To to enter the phone number you want all
your calls forwarded to.
assign voice names to contacts
1
2
3
Press
[New Contact]
K
under Contacts and select
.
or
Assign a name, phone number and select
[Options]
2
You can specify a forwarding number for
each type of missed call by selecting
Detailed and choosing the following options:
.
Select Voice Name and follow the prompt to
record the voice name. Press to stop
recording and store the voice name.
r
If Busy: When your handset is on a call or
transferring data.
4
Press under Back and under Save.
K
K
If No Answer: When you do not answer on
the first 4 rings.
place a call using a voice name
Press the speaker key until you are
prompted to say the voice name.
The handset will automatically place the call.
If Unreachable: When your handset is out of
coverage or powered off.
1
)
call features
80
are in a location where your phone's GPS
antenna has established a clear view of the
open sky and your local emergency response
center has the equipment to process location
information. Because of the limitations of this
feature, always provide your location, to the
best of your knowledge, to the emergency
response center when you make an
emergency calls
Your service provider programs one or more
emergency phone numbers that you can call
under any circumstances. Emergency calls
can be made without a SIM card, when your
phone is locked, or when the SIM card is
blocked.
emergency call
.
Note: Emergency numbers vary by country.
Your phone’s preprogrammed emergency
number(s) may not work in all locations, and
sometimes an emergency call cannot be
placed due to network, environmental, or
interference issues.
Note: Emergency calls cannot be placed
while the keypad is locked, or if your phone is
displaying a No Service message on the screen.
To unlock the keypad, if the slide is closed,
push up the slide to reveal the keypad. If the
slide is open, press
under Yes
K
under Unlock, and press
Dial 911 or your local emergency number to
be connected to an emergency response
center. If you are on an active call, you must
end it before making an emergency call.
K
.
international calls
If your phone service includes international
When you make an emergency call, your
phone’s GPS Enabled feature can help
emergency service personnel find you, if you
dialing, press and hold
0
to insert your local
call features
81
international access code (indicated by +).
Then, press the keypad keys to dial the
country code and phone number.
voicemail
To receive voice mail messages, you must
first set up a voice mail account with your
service provider.
speed dial
Each phone number stored in Contacts is
assigned a Speed Dial number, which you can
use to call that number.
receiving a message
When you receive a voice mail message, New
VoiceMail Message appears on the display.
1
From the home screen, use the keypad to
enter the Speed Dial number assigned to
the phone number you want to call.
To call your service provider’s voice mail
system and listen to the message:
1
Press
To dismiss the message notification:
Press or under Back
If the caller leaves a message, this icon
K
under Call.
2
3
Press
Press
#
.
2
,
.
•
r
K
.
turbo dial
3
appears on the display, reminding you that
you have a new message.
The first nine entries in your contacts are set
for turbo dial. They can be called by pressing
and holding the speed dial number
(1 through 9).
call features
82
customize
4
When you are finished, press
K
under
ring tones
Done
.
To set the ring tone your phone makes when
you receive phone calls, call alerts, message
notifications, pictures sent using Send via PTT
or Datebook reminders:
Note: This icon
you set your phone to Silent. This icon
appears on the display if you set the phone to
,
appears on the display if
5
Vibrate All
.
Find it:
/
>
j
>
Ring Tones
set your phone to vibrate
1
2
Make sure Vibrate All is set to Off
.
You can set your phone to vibrate instead of
making a sound when you receive all phone
calls, Private calls, call alerts, message
notifications, pictures sent using Send via PTT,
and Datebook reminders.
Scroll through the list of ring tones and
select the one you want to assign.
Vibrate sets your phone to vibrate instead
of making a sound. Silent sets your phone
to neither vibrate nor make a sound.
Find it:
/
>
j
>
Ring Tones
>
Vibrate All
3
Select the features you want to assign the
ring tone to.
Set this option to On or Locked
.
customize
83
Setting this option to On lets you turn Vibrate All
off by pressing the up volume control. Setting
this option to Locked requires you to press and
hold the up volume control to turn Vibrate All off.
The Locked option helps prevent you from
accidentally turning Vibrate All off.
4
When you are finished, press
K
under
Done
.
backlight
Set the amount of time that the display and
java apps. backlights remain on, or turn off the
PTT backlight feature to extend battery life.
To set Vibrate All to On or Locked using the volume
controls:
Find it:
/
>
u
>
Display/Info
>
Backlight
Press the volume controls to turn down the
volume as far as possible to set Vibrate All to On
.
Continue to hold the down volume control to
wallpaper
set Vibrate All to Locked
.
Set a previously saved photo or picture as a
wallpaper (background) image in your phone’s
display or throughout all menu screens.
To set your phone to vibrate instead of making
a sound for some features but not others:
Find it:
/
>
j
>
Ring Tones
Find it:
/
>
u
>
Display/Info
>
Wallpaper
1
2
3
Make sure Vibrate All is set to Off
.
1
2
Select Wallpaper
Scroll through the list of pictures and
press to select a picture.
.
Select Vibrate from the list of ring tones.
Select the features you want to set to
make no sound.
r
customize
84
You can set the wallpapers to change
automatically after a certain period of time by
turning on the Auto Cycle feature located in the
feature
event
reminder
When an event reminder
occurs press under View.
K
Wallpaper menu. You can select from 5 minutes
,
Press K under Back to close
the reminder.
15 minutes
,
1 hour
,
8 hours
,
Daily, or Startup
.
receive
datebook
events via
PTT
To view the information
while still in the Private call
datebook
feature
press
r.
create
datebook
events
To create a new Datebook
event press
Datebook
The 5 most recent events
received from a Private ID
are stored with the that
Private ID on the recent calls
list.
/
[New Event].
>
C
>
>
see
datebook
event
To see a calendar event
press
Press
/
;
>
C
>
Datebook.
left or right to see
up or down
to see the events.
To store events to the
the day and
;
Datebook press
K
under
Save while viewing the event
you want to store.
customize
85
datebook setup
options
Find it:
/
>
C
>
Datebook
>
/
>
Setup
Clock: Controls whether the time and date
appear on the home screen; sets time and
date format; sets year.
You can view or change these options:
options
Start View: Sets Datebook to start in day view,
week view, or month view when you
access Datebook.
hide or show
location information
Your phone is equipped with a Location
feature for use in connection with location-
based services that may be available in the
future.
Daily Begin: Sets the beginning of your day.
This is the earliest time of day displayed in
week view, if you have a 12-hour day view.
Delete After: Sets the amount of time
Datebook waits to delete an event after it
occurs.
Turning Location On will allow the network to
detect your position using GPS technology,
making some applications and services easier
to use. Turning Location off will disable the
GPS location function for all purposes except
911, but will not hide your general location
based on the cell site serving your call. No
application or service may use your location
Time Shift: Lets you shift the times of all
Datebook events. This is useful if you are
traveling to a different time zone.
Alert Timeout: Sets the amount of time a tone
continues to sound when you receive a
Datebook reminder.
customize
86
without your request or permission.
GPS-enhanced 911 is not available in all areas.
option
By Permission: When an application attempts to
view the location of your phone, you will be
prompted to give permission. However,
location information may still be available to
the phone’s owner, fleet manager, or
account administrator.
set your privacy options
Find it:
/
>
C
>
GPS Privacy
>
Select from the following options:
option
Restricted: No Java or similar software
change GPS PIN
When you receive your phone, your GPS PIN
is 0000.
applications may view the location of your
phone. However, location information may
still be available to the phone’s owner, fleet
manager, or account administrator.
To change your GPS PIN press
/
>
u
>
Unrestricted: All applications may view the
location of your phone, without notifying
you.
Security
>
Change Passwords
>
GPS PIN. Enter the
current GPS PIN and enter the new four to
eight digit GPS PIN. Re-enter the new four- to
eight-digit GPS PIN to confirm.
customize
87
Legal and Safety
•
•
•
•
•
United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
Safety and General Information
This section contains important information on the safe and
efficient operation of your mobile device. Read this
information before using your integrated multi-service
portable radio.*
American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.*
Exposure to Radio Frequency (RF) Energy
International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
Your mobile device contains a transmitter and receiver. When it is
ON, it receives and transmits RF energy. When you communicate
with your phone, the system handling your call controls the power
level at which your phone transmits.
Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
Your mobile device is designed to comply with local regulatory
requirements in your country concerning exposure of human beings
to RF energy.
•
•
Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
Portable Radio Product Operation and EME
Exposure
ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) “Regulation of the limitation of exposure to
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
*
The information provided in this document supersedes the general
safety information in user’s guides published prior to May 1, 2006
Legal and Safety
88
electrical, magnetic, and electromagnetic fields in the
radio frequency range between 9 kHz and 300 GHz.”
“Attachment to Resolution 303 from July 2, 2002."
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one
to two inches (2.5 to 5 cm) away from the
lips
.
Operational Precautions
For optimal mobile device performance, and to be sure that human
exposure to RF energy does not exceed the guidelines set forth in
the relevant standards, always follow these instructions and
precautions.
If you wear the mobile device on your body,
always place the mobile device in a Motorola approved clip,
holder, holster, case or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola and are not using the
mobile device in the intended use positions along side the head in
the phone mode or in front of the face in the two-way radio mode,
or if you hang your device from a lanyard around your neck, keep
the device at least 2.5 centimeters (1 inch) from your body when
transmitting.
Phone Operation
When placing or receiving a phone call, hold your mobile phone as
you would a landline telephone. Speak directly into the
microphone
.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
visit our website at www.motorola.com/phoneaccessories.
Two-way radio operation
Your radio product has been designed and tested to comply with
national and international standards and guidelines regarding
human exposure to RF electromagnetic energy, when operated in
the two-way mode (at the face, or at the abdomen when using an
audio accessory) at usage factors of up to 50% talk/50% listen.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference
from external sources if inadequately shielded, designed or
otherwise configured for RF energy compatibility. In some
circumstances your mobile device may cause interference with
other devices.
Transmit no more than the rated duty factor of 50% of the time. To
transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important
because this radio generates measurable RF energy only when
transmitting (in terms of measuring for standards compliance).
Legal and Safety
89
your mobile device with your implantable medical device, consult
your health care provider.
Follow Instructions to Avoid Interference
Problems
Turn OFF your mobile device in any location where posted notices
Hearing Aids
Some phones may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid
manufacturer or physician to discuss alternatives.
instruct you to do so.
In an aircraft, turn off your mobile device whenever instructed to
do so by airline staff. If your mobile device offers an airplane mode
or similar feature, consult airline staff about using it in flight.
Other Medical Devices and Health Care Facilities
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker
or defibrillator, consult your physician before using this mobile
device.
Persons with implantable medical devices should observe the
following precautions:
If you use any other personal medical devices, consult your
physician or the manufacturer or your device to determine if it is
adequately shielded from RF energy. Turn off your radio product
when instructed to do so in hospitals or health care facilities that
may be using equipment that is sensitive to external RF energy.
Bluetooth
•
ALWAYS keep the mobile device more than 20
centimeters (8 inches) from the implantable medical
device when the phone is turned ON.
This device supports Bluetooth 1.2 including HSP, HFP, OPP, DUN,
PBAP, and BPP. In order for Bluetooth devices to communicate with
one another, they must utilize the same Bluetooth profile. To
determine the profiles supported by other Motorola devices, visit
www.hellomoto.com/bluetooth. For other devices, contact their
respective manufacturer.
•
•
DO NOT carry the mobile device in the breast pocket;
Use the ear opposite the implantable medical device to
minimize the potential for interference.
•
Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
Certain Bluetooth features including those listed may not be
supported by all compatible Bluetooth-enabled devices, and/or the
functionality of such features may be limited in certain devices, or
by certain wireless carriers. Contact your wireless carrier about
feature availability and functionality.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about using
Legal and Safety
90
Caring for the Environment by
Recycling
Driving Precautions
The use of wireless phones while driving may cause distraction.
Discontinue a call if you can’t concentrate on driving.
This symbol on a Motorola product means the
product should not be disposed of with household
waste.
Additionally, the use of wireless devices and their accessories may
be prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
Disposal of your Mobile Device and Accessories
Responsible driving practices can be found in the “Smart Practices
Please do not dispose of mobile devices or electrical accessories
(such as chargers, headsets, or batteries) with your household
waste. These items should be disposed of in accordance with the
national collection and recycling schemes operated by your local or
regional authority. Alternatively, you may return unwanted mobile
devices and electrical accessories to any Motorola Approved
Service Center in your region. Details of Motorola approved
national recycling schemes, and further information on Motorola
recycling activities can be found at: www.motorola.com/recycling
Operational Warnings
Obey all posted signs when using Mobile devices in public areas.
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not
always posted, and can include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, or areas
where the air contains chemicals or particles, such as grain, dust
or metal powders.
Disposal of your Mobile Device Packaging and
User’s Guide
When you are in such area, turn off your handset, and do not
remove, install, or charge batteries unless it is a radio product type
especially qualified for use in such areas as “Intrinsically Safe” (for
example, Factory Mutual, CSA, or UL approved). In such areas,
sparks can occur and cause an explosion or fire.
Product packaging and user’s guides should only be disposed of in
accordance with national collection and recycling requirements.
Please contact your regional authorities for more details.
Legal and Safety
91
Symbol Key
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Symbol
Definition
Listening at full volume to
music or voice through a
headset may damage your
hearing.
Symbol
Definition
032374o
Important safety information
follows.
Batteries and Chargers
Do not dispose of your battery
or phone in a fire.
Caution: Improper treatment or use of batteries may present
a danger of fire, explosion, leakage, or other hazard. For
more information, see the “Battery Use and Battery Safety”
section in this user’s guide.
Your battery or phone may
require recycling in
032375o
accordance with local laws.
Contact your local regulatory
authorities for more
Keep Your Mobile Device and Its Accessories
Away from Small Children
These products are not toys and may be hazardous to small
children. For example:
information.
Do not throw your battery or
phone in the trash.
•
•
A choking hazard may exist for small, detachable parts.
Improper use could result in loud sounds, possibly causing
hearing injury.
Your phone contains an
internal lithium ion battery.
Li Ion BATT
032378o
•
Improperly handled batteries could overheat and cause a
burn.
Do not let your battery,
charger, or phone get wet.
Glass Parts
Some parts of your mobile device may be made of glass. This glass
could break if the product is dropped on a hard surface or receives
Legal and Safety
92
a substantial impact. If glass breaks, do not touch or attempt to
remove. Stop using your mobile device until the glass is replaced
by a qualified service center.
•
•
•
Limit the amount of time you use headsets or headphones
at high volume.
Avoid turning up the volume to block out noisy
surroundings.
Seizures/Blackouts
Turn the volume down if you can’t hear people speaking
near you.
Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when playing video
games. These may occur even if a person has never had a previous
seizure or blackout.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or muffled
speech, you should stop listening to the device through your
headset or headphones and have your hearing checked.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-lights
feature (if available) on your mobile device.
For more information about hearing, see our Web site at
www.motorola.com/hearingsafety (in English only).
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is always
a good idea to hold the screen away from your eyes, leave the
lights on in the room, take a 15-minute break every hour, and stop
use if you are very tired.
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience occasional
discomfort in your hands, arms, shoulders, neck, or other parts of
your body. If you continue to have discomfort during or after such
use, stop use and see a physician.
Caution About High Volume Usage
Warning: Warning: Exposure to loud noise from any
source for extended periods of time may affect your
hearing. The louder the volume sound level, the
Open Source Software Information
For instructions on how to obtain a copy of any source code being
made publicly available by Motorola related to software used in
this Motorola mobile device you may send your request in writing
to the address below. Please make sure that the request includes
the model number and the software version number.
less time is required before your hearing could be
affected. To protect your hearing:
Legal and Safety
93
MOTOROLA, INC.
OSS Management
600 North US Hwy 45
Libertyville, IL 60048
USA.
Export Law Assurances
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation
or re-exportation of this product to certain destinations. For further
information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
The Motorola website opensource.motorola.com also contains
information regarding Motorola’s use of open source.
Motorola has created the opensource.motorola.com to serve as a
portal for interaction with the software community-at-large.
Battery Use and Safety
To view additional information regarding licenses,
•
Motorola recommends you always use
Motorola-branded batteries and chargers. The
warranty does not cover damage caused by non-Motorola
batteries and/or chargers.
acknowledgments and required copyright notices for open source
packages used in this Motorola mobile device, please select
Main Menu > Java Apps > OpenSourceNotices. In addition,
this Motorola device may include self-contained applications that
present supplemental notices for open source packages used in
those applications.
Caution: Use of an unqualified battery or charger may
present a risk of fire, explosion, leakage, or other hazard.
Improper battery use, or use of a damaged battery, may
result in a fire, explosion, or other hazard.
Service and Repairs
If you have questions or need assistance, we’re here to help.
Go to www.motorola.com/support, where you can select from
a number of customer care options. You can also contact the
Motorola Customer Support Center at 1 (800) 453-0920 (United
States), 1 (877) 483-2840 (TTY, TDD United States for hearing
impaired).
•
•
Battery usage by children should be supervised.
Important: Motorola mobile devices are designed to work
best with qualified batteries. If you see a message on your
display such as Invalid Battery or Unable to Charge, take the
following steps:
•
Remove the battery and inspect it to confirm it bears a
Motorola “Original Equipment” hologram;
Legal and Safety
94
•
•
•
If there is no hologram, the battery is not a qualified
battery;
with the battery contact points, the battery could become
very hot.
If there is a hologram, replace the battery and retry
charging it;
•
Don’t place your battery near a heat source.
Excessive heat can damage the phone or the battery. High
temperatures can cause the battery to swell, leak, or
malfunction. Therefore:
If the message remains, contact a Motorola Authorized
Service Center.
•
•
Do not dry a wet or damp battery with an appliance or
heat source, such as a hair dryer or microwave oven.
•
•
When storing your battery, keep it in a cool, dry place.
It is normal over time for battery life to decrease, and for
the battery to exhibit shorter runtime between charges or
require more frequent or longer charging times.
Avoid leaving your phone in your car in high temperatures.
DOs
Important: Handle and store batteries properly to avoid
injury or damage. Most battery issues arise from improper
handling of batteries, and particularly from the continued use of
damaged batteries.
•
Do avoid dropping the battery or phone. Dropping
these items, especially on a hard surface, can potentially
cause damage.
•
Do contact your service provider or Motorola if your
phone or battery has been damaged from dropping
or high temperatures.
DON’Ts
•
Don’t disassemble, crush, puncture, shred, or
otherwise attempt to change the form of your
battery.
Important: Use Motorola Original products for quality
assurance and safeguards. To aid consumers in identifying
authentic Motorola batteries from non-original or counterfeit
batteries (that may not have adequate safety protection), Motorola
provides holograms on its batteries. Consumers should confirm
that any battery they purchase has a “Motorola Original”
hologram.
•
Don’t let the phone or battery come in contact with
water. Water can get into the phone’s circuits, leading to
corrosion. If the phone and/or battery get wet, have them
checked by your carrier or contact Motorola, even if they
appear to be working properly.
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
•
Don’t allow the battery to touch metal objects. If
metal objects, such as jewelry, stay in prolonged contact
Legal and Safety
95
display such as Invalid Battery or Unable to Charge, take the following
Warning: Never dispose of batteries in a fire because they may
explode.
steps:
•
•
•
•
Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
Battery Charging
If there is no hologram, the battery is not a Motorola
battery;
Notes for charging your phone’s battery:
•
When charging your battery, keep it near room
temperature. Never expose batteries to temperatures
below 0°C (32°F) or above 45°C (113°F) when charging.
If there is a hologram, replace the battery and retry
charging it;
If the message remains, contact a Motorola authorized
service center.
•
•
New batteries are not fully charged.
New batteries or batteries stored for a long time may take
more time to charge.
Important: Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or chargers.
•
Motorola batteries and charging systems have circuitry
that protects the battery from damage from overcharging.
Warning: Use of a non-Motorola battery or charger may present a
risk of fire, explosion, leakage, or other hazard.
Proper and safe battery disposal and recycling: Proper
battery disposal is not only important for safety, it benefits the
environment. Consumers may recycle their used batteries in many
retail or service provider locations. Additional information on
proper disposal and recycling may be found on the Web:
Specific Absorption Rate
Your model wireless phone meets the governmental
requirements for exposure to radio waves.
Your mobile device is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure to
radio frequency (RF) energy set by the Federal Communications
Commission (FCC) of the U.S. Government and by the Canadian
regulatory authorities. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the
general population. The guidelines are based on standards that
•
•
www.motorola.com/recycling
www.rbrc.org/call2recycle/ (in English only)
Disposal: Promptly dispose of used batteries in accordance with
local regulations. Contact your local recycling center or national
recycling organizations for more information on how to dispose of
batteries.
Legal and Safety
96
were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed for the
safety of all persons, regardless of age or health, and to account
for any variations in measurements.
depending upon available accessories and regulatory
requirements. The SAR information includes the Motorola testing
protocol, assessment procedure, and measurement uncertainty
range for this product.
While there may be differences between the SAR levels of various
mobile devices and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in the
SAR value for later products; in all cases, products are designed to
be within the guidelines.
The exposure standard for mobile devices employs a unit of
measurement known as the Specific Absorption Rate (SAR). The
SAR limit set by the FCC and by the Canadian regulatory
authorities is 1.6 watts per kilogram (W/kg), averaged over one
gram of tissue. Tests for SAR are conducted using procedures
accepted by the FCC and by Industry Canada with the mobile
device transmitting at its highest certified power level in all tested
frequencies. Although the SAR is determined at the highest
certified power level, the actual SAR level of the mobile device
while operating can be below the maximum value. This is because
the mobile device is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
general, the closer you are to a wireless base station, the lower
the power output.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) Web site:
http://www.phonefacts.net
or the Canadian Wireless Telecommunications Association (CWTA)
Web site:
http://www.cwta.ca
AGPS and Emergency Calls
When you make an emergency call, your mobile device can use
Assisted Global Positioning System (AGPS) satellite signals to tell
the emergency response center your approximate location.
Before a mobile device is available for sale to the public in the U.S.
and Canada, it must be tested and certified to the FCC and Industry
Canada that it does not exceed the limit established by each
government for safe exposure. The tests are performed in
positions and locations (e.g., at the ear and worn on the body)
submitted to the FCC and available for review by Industry Canada.
The highest SAR value for this mobile device when tested for use
at the ear is 0.88 W/kg, and when worn on the body, as described
in this guide, is 1.15 W/kg. Body-worn measurements can differ,
The AGPS feature has limitations, so always tell the emergency
response center your best knowledge of your location. Remain on
the phone for as long as the emergency response center instructs
you.
Legal and Safety
97
AGPS might not work for emergency calls, if your local
emergency response center does not process AGPS location
information. For details, contact your local authorities.
Motorola Limited Warranty for the
United States and Canada
If your mobile device cannot find strong AGPS satellite signals, the
location of the nearest cell tower in contact with your mobile
device is automatically provided to the emergency response
center.
What Does this Warranty Cover?
Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES
AND SOFTWARE PURCHASED IN THE UNITED STATES OR
CANADA
AGPS Performance Tips
Subject to the exclusions contained below, Motorola, Inc. warrants
its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for
use with these Products ("Accessories") and Motorola software
contained on CD-Roms or other tangible media and sold for use
with these Products ("Software") to be free from defects in
materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to
new Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
•
Go outside and away from underground locations, covered
vehicles, structures with metal or concrete roofs, tall
buildings, and foliage. Indoor performance might improve
if you move closer to windows, but some window sun
shielding films can block satellite signals.
•
Move away from radios, entertainment equipment, and
other electronic devices that might interfere with or block
AGPS satellite signals.
AGPS uses satellites controlled by the U.S. government and
subject to changes implemented in accordance with the
Department of Defense AGPS user policy and the Federal Radio
Navigation Plan. These changes might affect AGPS performance.
Products Covered
Length of Coverage
Products as defined
above.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
Legal and Safety
98
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Products Covered
Length of Coverage
Accessories as
defined above.
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the product.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or neglect,
such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water,
rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola, are excluded from coverage.
Products or
The balance of the original
warranty or for ninety (90) days
from the date returned to the
consumer, whichever is longer.
Accessories that are
Repaired or
Replaced.
Software as defined
above. Applies only to
physical defects in the
media that embodies
the copy of the software
(e.g. CD-ROM, or floppy
disk).
Ninety (90) days from the date
of purchase
.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, including without limitation, software
changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from
coverage.
What is not covered? (Exclusions)
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Ornamental Decorations. Ornamental decorations such as
emblems, graphics, rhinestones, jewels, gemstones and their
settings, and other decorative elements, are excluded from
coverage.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
Legal and Safety
99
non-Motorola housings, antennas, or parts, are excluded from
coverage.
How to Obtain Warranty Service or Other Information? To
obtain service or information, please call:
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
Motorola iDEN Customer Services 1-800-453-0920 or
954-723-4910
TTY-877-483-2840
Or visit us online at http://www.motorola.com/iden
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications provided
by third parties, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software
products will be corrected.
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
Software NOT Embodied in Physical Media. Software that is
not embodied in physical media (e.g. software that is downloaded
from the internet), is provided "as is" and without warranty.
What Other Limitations Are There? ANY IMPLIED
Who is covered? This warranty extends only to the first
consumer purchaser, and is not transferable.
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
What will Motorola Do? Motorola, at its option, will at no
charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty.
We may use functionally equivalent
reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to
your Product, Accessory or Software, including but not limited to
personal contacts, games and ringer tones, will be reinstalled. To
avoid losing such data, software and applications please create a
back up prior to requesting service.
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
Legal and Safety
100
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,
ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
purchaser in any such suit which are attributable to any such
claim, but such defense and payments are conditioned on the
following:
•
That MOTOROLA will be notified promptly in writing by
such purchaser of any notice of such claim;
•
That MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or
compromise; and
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from
state to state or from one jurisdiction to another.
•
Should the Product or parts become, or in MOTOROLA’S
opinion be likely to become, the subject of a claim of
infringement of a patent, that such purchaser will permit
MOTOROLA, at its option and expense, either to procure
for such purchaser the right to continue using the Product
or parts or to replace or modify the same so that it
becomes non infringing or to grant such purchaser a credit
for the Product or parts as depreciated and accept its
return. The depreciation will be an equal amount per year
over the lifetime of the Product or parts as established by
MOTOROLA.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and distribute
copies of the Motorola software. Motorola software may only be
copied into, used in, and redistributed with, the Products
associated with such Motorola software. No other use, including
without limitation disassembly of such Motorola software or
exercise of the exclusive rights reserved for Motorola, is
permitted.
MOTOROLA will have no liability with respect to any claim of
patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have
any liability for the use of ancillary equipment or software not
furnished by MOTOROLA which is attached to or sued in
Patent and Software Provisions:
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a patent, and Motorola will
pay those costs and damages finally awarded against the end user
connection with the Product or any parts thereof. In no event shall
MOTOROLA be liable for any incidental, special or consequential
Legal and Safety
101
damages arising from any claim of patent infringement or alleged
infringement.
The wireless telephone industry has developed ratings for some of
their mobile phones, to assist hearing device users in finding
phones that may be compatible with their hearing devices. Not all
phones have been rated. Phones that are rated have the rating on
their box or a label on the box.
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
software, such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software
was originally embodied and such software in such Product may
not be replaced, copied, distributed, modified in any way, or used
to produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise or
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
The ratings are not guarantees. Results will vary depending on the
user’s hearing device and hearing loss. If your hearing device
happens to be vulnerable to interference, you may not be able to
use a rated phone successfully. Trying out the phone with your
hearing device is the best way to evaluate it for your personal
needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and
are likely to generate less interference to hearing devices than
phones that are not labeled. M4 is the better/higher of the two
ratings.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are
likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the
better/higher of the two ratings. (Note that not all hearing devices
have telecoils in them.)
Hearing Aid Compatibility With Mobile
Phones
Some Motorola phones are measured for compatibility with
hearing aids. If the box for your particular model has “Rated for
Hearing Aids” printed on it, the following explanation applies.
Hearing devices may also be measured for immunity to this type of
interference. Your hearing device manufacturer or hearing health
professional may help you find results for your hearing device. The
more immune your hearing aid is, the less likely you are to
experience interference noise from mobile phones.
When some mobile phones are used near some hearing devices
(hearing aids and cochlear implants), users may detect a buzzing,
humming, or whining noise. Some hearing devices are more
immune than others to this interference noise, and phones also
vary in the amount of interference they generate.
Legal and Safety
102
Information From the World Health
Organization
Present scientific information does not indicate the need for any
special precautions for the use of mobile phones. If you are
concerned, you may want to limit your own or your children’s RF
exposure by limiting the length of calls or by using hands-free
devices to keep mobile phones away from your head and body.
Wireless: The New Recyclable
Your wireless phone can be recycled. Recycling your phone
reduces the amount of waste disposed in landfills and allows
recycled materials to be incorporated into new products.
The Cellular Telecommunications Industry Association (CTIA) and
its members encourage consumers to recycle their phones and
have taken steps to promote the collection and environmentally
sound recycling of end-of-life devices.
Source: WHO Fact Sheet 193
As a phone user, you have an important role in ensuring that this
device is recycled properly. When it comes time to give this phone
up or trade it in for a new one, please remember that the phone,
the charger, and many of its accessories can be recycled. It's easy.
To learn more about CTIA's Recycling Program for Used Wireless
Devices, please visit us at:
Further information: http://www.who.int./peh-emf
.
Product Registration
Online Product Registration:
www.motorola.com/us/productregistration
http://recycling.motorola.young-america.com/ index.html
Product registration is an important step toward enjoying your new
Motorola product. Registering permits us to contact you for
product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is not
required for warranty coverage.
California Perchlorate Label
Some mobile phones use an internal, permanent backup battery on
the printed circuit board that may contain very small amounts of
perchlorate. In such cases, California law requires the following
label:
Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate
There is no special handling required by consumers.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt
to confirm warranty status.
.
Thank you for choosing a Motorola product.
Legal and Safety
103
manner to the extent allowed by law. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any third
party software provider, except for the normal, non-exclusive,
royalty-free license to use that arises by operation of law in the
sale of a product.
Patent and Trademark Information
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc. ® Reg.
U.S. Pat. & Tm. Off. © 2009 Motorola, Inc. All rights reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
T9 is a trademark owned by Tegic Communications.
T9®Text Input Patent and Trademark Information.
Privacy and Data Security
Motorola understands that privacy and data security are important
to everyone. Because some features of your mobile device may
affect your privacy or data security, please follow these
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and other
countries.
recommendations to enhance protection of your information:
•
•
•
Monitor access—Keep your mobile device with you and
do not leave it where others may have unmonitored
access. Lock your device’s keypad where this feature is
available.
All other product names or services mentioned in this manual are
the property of their respective trademark owners.
Keep software up to date—If Motorola or a
software/application vendor releases a patch or software
fix for your mobile device that updates the device’s
security, install it as soon as possible.
Software Copyright Notice
Motorola products may include copyrighted Motorola and third
party software stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for
Motorola and third party software providers certain exclusive
rights for copyrighted software, such as the exclusive rights to
distribute or reproduce the copyrighted software. Accordingly, any
copyrighted software contained in the Motorola products may not
be modified, reverse-engineered, distributed, or reproduced in any
Erase before recycling—Delete personal information
or data from your mobile device prior to disposing of it or
turning it in for recycling. For instructions on how to delete
all personal information from your device, please contact
your local service provider.
Legal and Safety
104
•
Understanding AGPS—To provide location information
for emergency calls, certain Motorola mobile devices
incorporate Assisted Global Positioning System (AGPS)
technology. AGPS technology also can be used in
non-emergency applications to track and monitor a user’s
location—for example, to provide driving directions. Users
who prefer not to permit such tracking and monitoring
should avoid using such applications.
•
•
Get to know your Motorola mobile device and its
features such as speed dial and redial. If available,
these features help you to place your call without taking
your attention off the road.
When available, use a handsfree
device. If possible, add an additional
layer of convenience to your phone with
one of the many Motorola Original
handsfree accessories available today.
If you have further questions regarding how the use of your mobile
device may impact your privacy or data security, please contact
provider.
•
Position your mobile device within easy reach. Be
able to access your phone without removing your eyes
from the road. If you receive an incoming call at an
inconvenient time, if possible, let your voice mail answer
it for you.
Smart Practices While Driving
Drive Safe, Call Smart SM
•
•
•
Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
Check the laws and regulations on the use of phones and
their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas—for example handsfree use
only. Go to www.motorola.com/callsmart (in English only)
for more information.
Your mobile device lets you communicate by voice and
data—almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving is
your first responsibility. If you choose to use your phone while
driving, remember the following tips:
Do not take notes or look up phone numbers while
driving. Jotting down a “to do” list or going through your
address book takes attention away from your primary
responsibility, driving safely.
Dial sensibly and assess the traffic; if possible,
place calls when your car is not moving or before
pulling into traffic. If you must make a call while
moving, dial only a few numbers, check the road and your
mirrors, then continue.
Legal and Safety
105
•
Do not engage in stressful or emotional
conversations that may be distracting. Make people
you are talking with aware you are driving and suspend
conversations that can divert your attention away from the
road.
•
•
Use your mobile device to call for help. Dial 911 or
other local emergency number in the case of fire, traffic
accident, or medical emergencies (wherever wireless
phone service is available).
Use your mobile device to help others in
emergencies. If you see an auto accident, crime in
progress, or other serious emergency where lives are in
danger, call 911 or other local emergency number
(wherever wireless phone service is available), as you
would want others to do for you.
•
Call roadside assistance or a special
non-emergency wireless assistance number when
necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a vehicle you
know to be stolen, call roadside assistance or other
special non-emergency wireless number (wherever
wireless phone service is available).
Legal and Safety
106
drafts
see also text messages,
H
M
Hearing Aid Compatibility
memory card 9
E
I
message center
images
F
frequently asked questions
G
N
L
GPS enabled
O
index
108
optional accessory 8
optional feature 8
P
T
private calls
S
safety
R
SIM card 9
index
109
www.motorola.com
NNTN7815A
xxxxxxxx xx xx MAY/09
Printed in USA
|