Marantz HDMI DV7001 User Manual

Model DV7001 User Guide

Super Audio CD/DVD Player

CLASS 1 LASER PRODUCT

LUOKAN LASERLAITE

KLASS 1 LASERAPPARAT

Additional Safety Information!

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

•

This product should not be placed in a built-in installation

such as a bookcase or rack unless proper ventilation is

provided or the manufacturer’s instructions have been

adhered to.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

•

Apparatus shall not be exposed to dripping or splashing

and that no objects ﬁlled with liquids, such as vases,

shall be placed on the apparatus.

When the switch is in the OFF position, the apparatus

isn’t completely switched-off from the MAINS.

7) Do not block any ventilation openings, Install in

accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators,

heat registers, stoves or other apparatus (including

ampliﬁers) that produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult an

electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience

receptacles, and the point where

they exit from the apparatus.

11) Only use attachments/accessories

speciﬁed by the manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table speciﬁed by the

manufacturer, or sold with the apparatus. When a cart

is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when

unused for long periods of time.

14) Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

- Make a space of about 0.1 meter around the

unit.

FCC NOTE (for U. S. A only):

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures.

- No objects ﬁlled with liquids, such as vases,

shall be placed on the equipment.

- When the switch is in the OFF position, the

equipment is not completely switched off from

MAINS.

- The equipment shall be installed near the

power supply so that the power supply is

easily accessible.

WARRANTY

For warranty information, contact your local Marantz dis-

tributor.

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and re-

ceiver.

RETAINYOUR PURCHASE RECEIPT

•

Connect this equipment into an outlet on a circuit differ-

ent from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

Your purchase receipt is your permanent record of a valua-

ble purchase. It should be kept in a safe place to be referred

to as necessary for insurance purposes of when corre-

sponding with Marantz.

NOTE: Changes or modiﬁcations may cause

this unit to fail to comply with Part 15 of the

FCC Rules and may void the user’s authority to

operate the equipment.

IMPORTANT

When seeking warranty service, it is the responsibility of the

consumer to establish proof and date of purchase. Your pur-

chase receipt or invoice is adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer’s statutory

rights and does not affect those rights in any way.

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de la Classe B est

conforme á la norme NMB-003 du Canada.

Disc Storage

Be careful not to harm the disc because the data on these

discs is highly vulnerable to the environment.

This product satisﬁes FCC regulations when shielded cables

and connectors are used to connect the unit to other equip-

ment. To prevent electromagnetic interference with electric

appliances, such as radios and televisions, use shielded

cables and connectors for connections.

•

Do not keep under direct sunlight.

Keep in a cool ventilated area.

Store vertically.

Keep in a clean protection jacket.

Maintenance of Cabinet

For safety reasons, be sure to disconnect the AC power cord

from the AC outlet.

•

Do not use benzene, thinner, or other solvents for clean-

ing.

Wipe the cabinet with a soft cloth.

CE marking (for Europe only)

•

This product is in conformity with the

EMC directive and low-voltage directive.

A NOTE ABOUT RECYCLING

WARNINGS

- Do not expose the equipment to rain or mois-

ture.

This product’s packaging materials are

recyclable and can be reused. This product

and the accessories packed together are the

applicable product to the WEEE directive except

batteries.

- Do not remove the cover from the equipment.

- Do not insert anything into the equipment

through the ventilation holes.

Please dispose of any materials in accordance

with your local recycling regulations.

When discarding the unit, comply with your local

rules or regulations.

Batteries should never be thrown away or

incinerated but disposed of in accordance with

your local regulations concerning chemical

wastes.

- Do not handle the mains cord with wet hands.

- Do not cover the ventilation with any items

such as tablecloths, newspapers, curtains, etc.

- No naked ﬂame sources, such as lighted can-

dles, should be placed on the equipment.

- When disposing of used batteries, please

comply with governmental regulations or envi-

ronmental public instruction’s rules that apply

in your country or area.

Table Of Contents

DVD Setup Menu

Before You Start

Using the FL menu................................................................. 34

Setting up the GENERAL SETUP page.............................. 36

Setting up the AUDIO SETUP page.................................. 39

Setting up the VIDEO SETUP page................................... 44

Setting up the PREFERENCE page..................................... 50

Features.......................................................................................6

What’s in the box......................................................................7

Putting the batteries in the remote control........................7

Using the remote control .......................................................7

Discs compatible with this player.........................................8

DVD-Video regions...................................................................9

General information.................................................................9

MP3 compatibility information .............................................9

WMA compatibility information............................................9

JPEG compatibility information .............................................9

DivX compatibility information .............................................9

Additional Information

Language Codes .................................................................... 54

Handling discs........................................................................ 55

Storing discs........................................................................... 55

Discs to avoid......................................................................... 55

Cleaning the pickup lens...................................................... 55

Connecting Up

Problems with condensation............................................... 55

Hints on installation.............................................................. 56

Moving the player.................................................................. 56

Precautions on using the power cord............................... 56

Easy setup................................................................................10

Home theater video connections .......................................11

Home theater audio connections.......................................12

Troubleshooting..................................................................... 57

Speciﬁcations ......................................................................... 60

Controls & Displays

Front panel...............................................................................13

Remote control .......................................................................14

Getting Started

Playing discs ............................................................................16

Basic playback controls.........................................................16

Resuming playback from the last stopped point.............16

Navigating DVD disc menus.................................................17

Navigating Video CD PBC menus .......................................17

Playing Discs

Introduction.............................................................................18

Preview function......................................................................18

Fast Forward/Fast Reversed................................................. 20

Still Frame/Slow Play/Frame Advance Playback...............21

Using the page....................................................................... 22

Using the Repeat Play .......................................................... 22

Looping a section of a disc ................................................. 23

Using the Random (SHUFFLE) Play................................... 23

Switching Camera Angles..................................................... 24

Switching the Subtitle Language ....................................... 24

Switching the Audio Language ......................................... 25

Switching the audio channel............................................... 25

Switching Super Audio CD Playback layer....................... 25

Switching Super Audio CD Playback area........................ 25

Using the Zoom Function.................................................... 25

Play back Information........................................................... 26

Playing a JPEG image ﬁle (slide show) .............^™................. 30

Playing an MP3/DivX/JPEG/Windows Media

Audio disc ............................................................................... 29

Playing MP3/WMA music and JPEG pictures

simultaneously.........................................................................31

Playing a DivX disc................................................................ 32

Using the Setup Menu ......................................................... 33

Before You Start

Superlative audio performance with

Super Audio CD, DVD-Audio, Dolby*

Features

An HDCP-compatible HDMI*

Digital and DTS* software

terminal is provided for fully digital

transmission that ensures the very

highest picture and digital sound

quality.

Logos:

The DV7001 delivers breathtaking sound

quality with Super Audio CD, DVD-Audio,

Dolby Digital and DTS discs.

This unit comes with a High-Deﬁnition

Multimedia Interface (HDMI) jack; an

extended DVI interface for next-generation

televisions. This interface allows transfers

of uncompressed digital video and digital

audio (audio streams such as Dolby Digital

and DTS as well as linear PCM) with a

single connector. HDMI standard Ver. 1.1

DivX

You can enjoy DivX ﬁles which are

recorded on DVD R/RW or CD-R/RW.

Plays DivX5.2, DivX4, DivX3 and DivX

VOD Video content (see pages 29, 32).

• This player supports Quarter Pixel.

compatibility means the unit can also

transfer DVD-Audio multi-channel audio

over HDMI.

• This player supports GMC.

MP3 and WMA*

compatibility

End-to-end full-digital transfers with all

digital processing allow the enjoyment

of realistic video without any image

This player is compatible with CD-R, CD-

RW and CD-ROM discs that contain MP3

and WMA audio tracks (see pages 29, 31).

degradation caused by AD/DA conversions.

And the unit can up-convert 480p video

signals to 720p, 1080i, and 1080p video

output signals using the scaling function

and the HDMI jack (see pages 11, 47).

JPEG compatibility

This player is compatible with CD-R, CD-

RW and CD-ROM discs that contain JPEG

data (see pages 29, 30, 31).

High quality 12-bit/216 MHz Video

D/A converter*

HDMI, the HDMI logo and High-Deﬁnition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

The unit uses a Video D/A converter that

performs D/A conversion of all video

signals in 12-bits and can perform 8x over-

sampling to let you enjoy beautiful video

possible with DVD. Furthermore, NSV

technology suppresses noise during DA

conversion.

“NSV” is a registered trademark of Analog Device

Co. Ltd.

“DCDi” is a registered trademark of Faroudja, a

division of Genesis Microchip, Inc.

Manufactured under license from Dolby

Laboratories. “Dolby” “Pro Logic” and the

double-D symbol are trademarks of Dolby

DCDi

Laboratories.

“DTS” and “DTS Digital Surround” are registered

DCDi (Directional Correction

trademarks of DTS, Inc.

Deinterlacing) computes and tracks the

angle of the screen edge to ﬁll in the

missing pixels on the TV screen. DCDi

signiﬁcantly optimizes the image quality,

especially during slow motion playback.

This function is available only for

progressive scan output.

“DivX”, and “DivX Ultra” Certiﬁed, and associated

logos are trademarks of DivX, Inc. and are used

under license.

Windows Media and the Windows logo are

trademarks, or registered trademarks of Microsoft

Corporation in the United States and/or other

countries.

High quality 24-bit/192 kHz DAC

The high speciﬁcation 24-bit/192 kHz DAC

delivers dynamic, smooth and expansive

analog sound from CDs and DVDs.

Before You Start

What’s in the box

Using the remote control

Thank you for buying this MARANTZ

Keep in mind the following when using the

remote control:

product. Please conﬁrm that the following

accessories are in the box when you open

•

Make sure that there are no obstacles between

the remote control and the remote sensor on the

unit.

it.

•

Remote control

Use within the operating range and angle, as

AAA/R03 dry cell batteries x2

Audio/Video cable (yellow/red/white)

System control cable

Power cable

shown.

5m (16 feet)

User Guide (this manual)

Warranty card

•

Remote operation may become unreliable if

strong sunlight or ﬂuorescent light is shining on

the unit’s remote sensor.

Putting the batteries in the remote

control

Remote controllers for different devices can

interfere with each other. Avoid using remotes for

other equipment located close to this unit.

Open the battery

compartment cover on

the back of the remote

control.

Replace the batteries when you notice a fall off in

the operating range of the remote control.

Note

Insert two AAA/R03

batteries into the battery

compartment following

ª ·

•

When using this player independently, set the

REMOTE CONTROL switch on the rear panel to

INT. (INTERNAL) (see page 10).

the indications (

)

inside the compartment.

Close the cover.

Note

Incorrect use of batteries can result in hazards such

as leakage and bursting. Please observe the following:

•

Don’t mix new and old batteries together.

Don’t use different kinds of battery together.

Although they may look similar, different batteries

may have different voltages.

•

Make sure that the plus and minus ends of each

battery match the indications in the battery

compartment.

Remove batteries from equipment that isn’t going

to be used for a month or more.

When disposing of used batteries, please comply

with governmental regulations or environmental

bylaws that apply in your country or area.

Before You Start

Super Audio CD compatibility:

Discs compatible with this player

Any disc that displays one of the following

logos should play in this player. Other

formats, including DVD-RAM, DVD-ROM,

CD-ROM (except those that contain MP3/

DivX/WMA/JPEG ﬁles) and Photo CD will

not play.

•

Logo:

•

Single layer, dual layer or Hybrid layer

12cm (5in.) or 8cm (3in.) discs

Digital audio (DSD)

Super Audio CDs are divided into tracks.

Audio CD compatibility:

DVD-Video compatibility:

•

Logos:

•

Logos:

•

12cm (5in.) or 8cm (3in.) discs

•

Single-sided or double-sided discs

Single layer or dual layer discs

Linear PCM digital audio

Audio CD, CD-R* and CD-RW* formats

Dolby Digital, DTS, MPEG or Linear PCM digital

CDs are divided into tracks.

audio

*This unit can play CD-R and CD-RW discs recorded

in Audio CD or Video CD format, or with MP3 audio

ﬁles or Windows Media audio ﬁles or picture ﬁles or

DivX ﬁles.

•

MPEG-2 digital video

Discs are generally divided into one or more titles.

Titles may be further subdivided into chapters.

*Some copy-controlled CDs may not conform to

DVD-Audio compatibility:

ofﬁcial CD standards. They are special discs and may

not play on the DV7001.

•

Logos:

*The DV7001 does not support the non-DVD side

•

Single sided discs

of a Dual Disc.

Single layer or dual layer discs

Video CD compatibility:

Linear or packed PCM digital audio

Some discs may contain MPEG-2 video, and

•

Logo:

Dolby Digital, DTS or MPEG digital audio

•

12cm (5in.) or 8cm (3in.) discs

Discs are generally divided into one or more groups.

Groups may be further subdivided into tracks.

MPEG-1 digital audio

MPEG-1 digital video

DVD-R compatibility:

Video CDs are divided into tracks.

This unit can play DVD-R discs. Please note the

following points when using these discs:

Super VCD compatibility:

•

Logo:

•

Logo:

•

This unit can play DVD-R discs recorded as DVD-

Video format.

•

12cm (5in.) or 8cm (3in.) discs

MPEG-1 digital audio

MPEG-2 digital video

DVD-RW compatibility:

Super VCDs are divided into tracks.

This unit can play DVD-RW discs. Please note the

following points when using these discs:

•

Logo:

•

This unit can play DVD-RW discs recorded as

DVD-Video format, and DVD-VR format.

•

DVD-RW discs that were recorded with copy-

once only permission can be played.

DVD+R/+RW compatibility:

•

Logo:

This unit can play DVD+R/+RW discs. Please

note the followings points when using these

discs.

Before You Start

•

This player can not play the disc contents

protected by Windows Media Digital Right

Management (DRM).

DVD-Video regions

JPEG compatibility information

•

While this player is designed to be able to

handle image data recorded in JPEG format,

no assurances are given that the player will be

able to display image data recorded in all JPEG

formats.

This player can not display progressive JPEG

images.

All DVD-Video discs carry a region mark

on the case somewhere that indicates

which region(s) of the world the disc is

compatible with. Your DVD player also has

a region mark, which you can ﬁnd on the

rear panel. Discs from incompatible regions

will not play in this player. Discs marked

ALL will play in any player.

•

This player can not display HD JPEG images.

Always be sure to specify a ﬁle extension of “.JPG”

or “JPEG” for JPEG ﬁles. The ﬁle will not be able

to be displayed if a ﬁle extension other than “.JPG”

or “JPEG” is speciﬁed or if no ﬁle extension is

assigned to the ﬁle. (Note that this means that

JPEG ﬁles created on a Macintosh will not be able

to be displayed as is.)

•

Depending on the ﬁle size and compression

ratio, some JPEG pictures cannot be displayed

correctly.

General information

•

This player can recognize in total about 650 ﬁles

per folders and 300 folder per disc for MP3/

DivX/WMA.

DivX compatibility information

When writing MP3/WMA/JPEG/DivX ﬁles to CD-

•

A ﬁle with an extension of “.avi” or “.divx” is called

a DivX ﬁle.

R/RW discs, always be sure to set the writing

format to ISO 9660 Level 1.

•

Maximum 30 characters can be displayed on the

display on the Front panel and TV screen.

For MP3 and WMA ﬁles recorded in Variable Bit

Rate (VBR), the unit may not display the actual

elapsed time.

•

Ca^Mut^axio^imn^u!^{m 4 Gbyte of ﬁle size can be displayed.}

•

File should be MPEG1 Audio Layer 3 format and

MPEG2 format.

MP3 compatibility information

•

Files should be MPEG1 Audio Layer 3 format.

The sampling rate is 8 kHz to 48 kHz, but it is

depends on the bit rate. Incompatible ﬁles will

not play.

•

DVD R/RW and CD-R/RW discs recorded using

a personal computer or a DVD or CD recorder

may not play if the disc is damaged or dirty, or if

there is dirt or condensation on the player’s lens.

Audio encoded at 128 kbps should sound close

to regular audio CD quality. Although this player

will play 32 kbps to 320 kbps, but it is depends

on the sampling rate.

If you record a disc using a personal computer,

even if it is recorded in a compatible format,

there are cases in which it may not play because

This player is compatible with ID3 ver.1.1 Tag.

of the settings of the application software used

But the information display on the display on the

to create the disc. (Check with the software

publisher for more detailed information.)

Front panel and TV screen is only ID3 ver. 1.0

Tag.

•

There may be times when it is impossible

•

Maximum 30 characters can be displayed on the

to replay a CD-R/RW disc because of the

display on the Front panel and TV screen.

characteristics of the disc being used or because

of dirt or scratches on the disc.

This player cannot play DVD-R/RW discs with

recorded MP3 music data.

•

Unﬁnalized DVD-R/RW discs cannot be played.

This player only plays tracks that are named

containing the ﬁle extension “.mp3” or “.MP3”.

Unﬁnalized CD-R/RW discs cannot be played.

For more information on using DVD-R/RW and

This player is not compatible with multi-session

CD-R/RW discs, see “Handling discs” on page

discs. If you try and play a multi-session disc,

only the ﬁrst session will be played.

55.

•

Never try to replay anything other than a music

CD (CDA format) or a CD-R/RW on which MP3

and/or JPEG ﬁles have been stored. Depending

on the type of ﬁle, there may be times when

doing so will result in problems or erroneous

operation.

WMA compatibility information

•

The sampling rate is 44.1 kHz (bit rate: 64

kbps-192 kbps) and 48 kHz (bit rate: 128

kbps-192 kbps).

This player only plays tracks that are named with

the ﬁle extension “.wma” or “.WMA”.

Connecting Up

Easy setup

Important

While a connected component is turned on,

do not unplug the power cord of this DVD

player from the wall outlet. The speaker may be

damaged.

This easy setup is the minimum set of

connections you need to start watching

DVD-Video discs. Both sound and picture

are fed directly to your TV using the

supplied audio/video cables. For other

possible connections, see pages 11 and 12.

•

Before making or changing any rear panel

connections, make sure that all components are

switched off and unplugged from the wall outlet.

RS-232C terminal/

Connect to a composite video

Connect to a pair of stereo audio

FLASHER IN

input on your TV using the

supplied Audio/Video cable.

inputs on your TV using the

Control terminal for use by

custom installers.

supplied Audio/Video cable. You

can connect a subwoofer to the

SUBWOOFER Jack.

OUT

AC IN

HDMI

Ver 1.1

AUDIO OUT

FRONT

MIXED

2CH

RS-232C

SURR.R

COAX.

SURR.L

SUB WOOFER

CENTER

VIDEO

COMPONENT

^B/P^BC^R/P^R

FLASHER IN

INT.

EXT.

OPT.

DIGITAL

OUT

VIDEO OUT

A/V EUROCONNECTOR

REMOTE

CONTROL

See Note:

Plug into a standard

AC wall outlet.

INT.

EXT.

Remote Switch

Connecting audio/video cables

Note

Be sure to insert each

•

When connecting to a standard TV, select

plug fully for the best

4:3 LETTER BOX or 4:3 PAN SCAN in the TV

Aspect setting (see page 45).

connection. The plugs

and jacks are color-coded

to make connection

easier.

Connect the video output of the player directly

to your TV. Because the player is designed

to support an Analog Protection System copy

protection there are cases when proper playback

will not be possible if the player is connected to

the TV through a VCR and images are recorded

and played on the VCR.

Connecting system control cables

By connecting this DVD player to another

•

The player’s video output and S1 output are not

Marantz audio component using a supplied

system control cable, you can remotely

operate the components as a single system.

be progressive.

Remote switch

When using this DVD player independently, set

this switch to INT. (INTERNAL). When using this

DVD player in a system with a Marantz receiver

equipped with a remote sensor, set the switch to

EXT. (EXTERNAL). Change the switch setting

using a pen with a sharp tip etc.

•

When connecting to a component with a

remote sensor, be sure to connect the REMOTE

CONTROL IN jack of this DVD player to

the REMOTE CONTROL OUT jack of the

component with the remote sensor.

•

When connecting to component which is

not equipped with a remote sensor, be sure

to connect the component to the REMOTE

CONTROL OUT jack of this DVD player.

•

Flasher Input

This is used when controlling components

from different rooms with a keypad or other

input device. Set the remote switch to EXT.

(EXTERNAL) when using a ﬂasher input.

Connecting Up

Home theater video connections

This player outputs video in a number

of different ways. Choose the one most

suitable for your system using the guide

below.

Important

•

Before making or changing any rear panel

connections, make sure that all components are

switched off and unplugged from the wall outlet.

While a connected component is turned on,

do not unplug the power cord of this DVD

player from the wall outlet. The speaker may be

damaged.

If your TV has a component video input, we

If your TV has a SCART input, we

recommend using it to connect directly to the

recommend using it to connect directly

COMPONENT VIDEO OUT of this player. Use

to the A/V EURO CONNECTOR on

the standard 3-jack component video output.

this player. (for Europe only)

OUT

AC IN

HDMI

Ver 1.1

AUDIO OUT

FRONT

MIXED

2CH

RS-232C

SURR.R

COAX.

SURR.L

SUB WOOFER

CENTER

C^R/P^R

VIDEO

COMPONENT

C^B/P^B

FLASHER IN

INT.

EXT.

OPT.

DIGITAL

OUT

VIDEO OUT

A/V EUROCONNECTOR

REMOTE

CONTROL

If your TV and projector have

If a component input is not

Plug into a standard

AC wall outlet.

a HDMI terminal for Video and

available to you, connect this

Audio Input, we recommend

player to your TV or AV receiver

using it to connect directly to

the HDMI out of this player.

using either the VIDEO or S1

jacks.

Connecting HDMI cables

Connecting SCART (for Europe only)

With an HDMI cable, both uncompressed

video data and digital audio data (e.g.,

LPCM or bit stream data such as Dolby

Digital, DTS, MPEG data or DVD Audio

Multi channel) can be transmitted with just

a single connector.

and S-Video cables

SCART and S-Video cables will only plug in

one way, so make sure the plug is correctly

lined up with the jack before inserting. Be

sure to fully insert for a good connection.

By transmitting DVD image data directly as

digital data without it being ﬁrst converted

into analog format, it becomes possible to

provide the very ﬁnest in image quality (see

pages 6, 41, 42, 47).

Note

•

The A/V EURO CONNECTOR can output

composite or RGB component video. If you

connect just one TV, use the A/V EURO

CONNECTOR. You can select the type of video

output by changing the COMPONENT setting in

the DVD Setup Menu (page 49).

Note

•

The HDMI output of this unit can be connected

to a DVI jack on a TV or other device using a

S-Video or composite video?

S-Video should give a better picture, so if

you have an S-Video input, use it. S-Video

cables are available from any good audio/

visual dealer.

conversion adapter. In this case, it is necessary

to use a TV or display with an HDCP-compatible

DVI input.

•

There may be no image output if connected to

a TV or display that is not compatible with the

above format.

Refer to the instruction manual of the TV or

display to be connected to this unit for detailed

information regarding the HDMI terminal.

When connecting a progressive input TV with the

component output of the player, select ON in

the Progressive setting (see

page 45

Connecting Up

Home theater audio connections

This player outputs multi-channel audio

in digital form. Check the manual for your

ampliﬁer/receiver to see what equipment it

is compatible with (especially which digital

formats such as Dolby Digital, DTS, etc. It

can decode).

Important

While a connected component is turned on,

do not unplug the power cord of this DVD

player from the wall outlet. The speaker may be

damaged.

•

Before making or changing any rear panel

connections, make sure that all components are

switched off and unplugged from the wall outlet.

If your ampliﬁer has 5.1 channel analog

If your ampliﬁer has stereo inputs

inputs, connect them here. Connect to the

only, connect them here. You

L (left)/R (right), SURR.L/.R (SURROUND

can connect a subwoofer to the

L/R), CENTER and SUB WOOFER inputs

of your ampliﬁer.

SUBWOOFER Jack.

OUT

AC IN

HDMI

Ver 1.1

AUDIO OUT

FRONT

MIXED

2CH

RS-232C

SURR.R

COAX.

SURR.L

SUB WOOFER

CENTER

VIDEO

COMPONENT

^B/P^BC^R/P^R

FLASHER IN

INT.

EXT.

OPT.

DIGITAL

OUT

VIDEO OUT

A/V EUROCONNECTOR

REMOTE

CONTROL

Connect to the coaxial or

Plug into a standard

AC wall outlet.

optical input of your ampliﬁer

if it has digital inputs.

the protective shutter will open and you

Connecting analog audio cables

should hear it click into position when fully

inserted. Be careful that you do not force

the plug, because this could result in dam-

Be sure to fully insert each plug for the

best connection. The plugs and jacks are

color-coded to make connection easier.

age to the protective shutter, the cable, or

the unit itself.

Connecting coaxial cables

Use an interconnector with a pin-type

(also called RCA

Note

COAX

•

If you listen to multichannel DVD-Audio through

one of the digital outputs, it will be downmixed

to stereo. Also, high sampling rate DVD-Audio

or phono) plug on

each end to connect

up digital coaxial-

(192 kHz or 176.4 kHz) will be downsampled

to 96 kHz, 88.2 kHz, 48 kHz or 44.1 kHz,

type jacks. Make

depending on the disc. Multi channel and high

sampling rate DVD-Audio are only available

through the analog outputs.

^sC^uo^ren^tn^hae^tc^tt^hi^en^pg^luo^gp^istical cables

pushed fully home.

•

All DVD-Audio and all Super Audio CD audio are

output only through the analog outputs. (see

page 40)

Optical intercon-

OPT

nects only plug in

one way, so make

sure the plug is

correctly lined up

with the jack before

insertion. When

inserting the plug,

Controls & Displays

Front panel

SUPER AUDIO CD/DVD PLAYER DV7001

PLAY

STOP

PAUSE

AUDIO EX.

HDMI

STANDBY

PRGSVE

GRP

OFF TITLE

SRS TS

THX

CHP

DOLBY

192kHz PCM MPEQ COND MP3

POWER ON/OFF

OFF

GRP

PROG

ALL

96kHz AWS VCD V-PART

AUDIO TOTAL SUB BTSTM MAP SACD DOWN MIX

AUDIO EX.

HDMI

OPEN/CLOSE

LFE

TEXT

10 11 12 13 14 15 16 17 18 19 20

STEREO MULTI

0 -

STANDBY indicator

10 AUDIO EX

•

Lights when the unit is in standby.

•

Press to turn AUDIO EX off and on.

HDMI video output cannot be switched off.

Disc tray

•

Place the disc here.

11 HDMI – page 47

•

(PLAY)

•

The HDMI on/off state toggles when pressed

Begins playing the disc play.

for three seconds or more. When on, the HDMI

(STOP)

indicator is lit.

•

Pressing this button while HDMI is enabled

displays the current resolution. Pressing this

button again while the resolution is displayed

allows you to select the resolution in the

sequence below:

•

Stops playing the disc play.

•

(PAUSE)

Pauses playing the disc play.

POWER ON/OFF

•

Press to turn the power on, and press it again to

turn the power off.

480p 576p 720p 1080 i 1080 p

AUDIO EX indicator

480p

•

Lights when the AUDIO EX is activated using the

AUDIO EX button on the remote control.

The sound quality of analog audio output is

improved by turning off analog video signal

output and the front panel display.

(OPEN/CLOSE)

•

Press to open and close the disc tray.

•

4 1

•

Press to skip reverse title/group, chapter, or track.

You can also press and hold this button for Fast

Reversed.

•

It is applied to CDDA, Super Audio CD, DVD

Audio and DTS CD in Play mode.

¡ ¢

Display

•

Press to skip forward title/group, chapter, or

•

Operation indications are displayed here.

track. You can also press and hold this button for

Fast Forward.

HDMI indicator

•

When the connected device is HDMI/DVI

compatible, the light ﬂashes red.

Controls & Displays

REPEAT – pages 22, 29

Remote control

A–B – page 23

ANGLE – pages 24, 30

% ﬁ

INPUT ( / ) button – These buttons

can switch between devices compatible with

MARANTZ receivers. Refer to the receiver

instruction manual for further details.

•

Applicable models: PM-11S1, PM-15S1,

PM6001, PM7001, PM8001, SR9600.

(These models may not be handled depending on

the area.)

Non-applicable models: MARANTZ Ampliﬁers

and receivers which had released before 2006,

including PM-14, PM-17 and PM4001 except

above models.

(

)

(PREV.)/

(NEXT)– Skip – pages

) for Fast Forward.

16, 17, 19, 20, 29, 30, 52

•

Allows you to search forward/backward through a

disc. Use to skip the title, chapter or track.

Press and hold (

) for Fast Reversed.

•

Press and hold (

SCAN – pages 18, 19

10 TOP MENU (TOP-M)/RETURN – page 17

2 3 5 ∞

11 Cursor (

/ ) / ENTER button

™

12 DISPLAY (DISP.) – page 26

13 DISC SKIP – It is not used on this set.

14 POWER – Switches the player on or into

standby – page 16

15 SOUND MODE– Selects Audio out mode

and change the Super Audio CD Play back

area – pages 25, 39

16 PAGE – Turns the pages of DVD-Audio still

pictures – page 22

17 RANDOM – page 23

18 AU D I O – Changes the Hybrid Super Audio

CD Play back layer – page 25

19 SUBTITLE – pages 24, 32

5 ∞

20 VOLUME ( / ) button – These buttons

AUDIO EX – Press to turn AUDIO EX off

can adjust the volume of devices compatible

with MARANTZ receivers. Refer to the

receiver instruction manual for further details.

21 MUTE button – This button can activate

the mute function of devices compatible with

MARANTZ receivers. Refer to the receiver

instructions for further details.

and on

•

The sound quality of analog audio output is

improved by turning off analog video signal

output and the front panel display.

HDMI video output cannot be switched off.

OPEN/CLOSE – Disc tray open/close –

page 16

(PLAY) – pages 16, 20, 21, 29, 31, 32

(PAUSE) – pages 16, 21

ZOOM – pages 25, 30

HDMI – page 47

(STOP) – pages 16, 30, 31, 33, 50

•

The HDMI on/off state toggles when pressed

for three seconds or more. When on, the HDMI

indicator is lit.

25 MENU – pages 17, 19, 24

26 SETUP – pages 33, 36, 39, 44, 50

27 Number buttons

Pressing this button while HDMI is enabled

displays the current resolution. Pressing this

button again while the resolution is displayed

allows you to select the resolution in the

sequence below:

480p 576p 720p 1080i 1080 p

480p

Controls & Displays

Note

•

HDMI ON is set when the unit is shipped from

the factory.

Set HDMI under the DVD Setup Menu to use

HDMI functions (see pages 41, 42, 47).

This remote control supports two remote control

codes: DVD1 and DVD2.

When the unit is shipped from the factory, the

remote control is set to DVD1.

To set the remote control to DVD2, hold down

both (STOP) button and 2 number button on

the remote control for at least ﬁve seconds. (If

the batteries in the remote control are replaced

while the remote control is set to DVD2, the

setting will revert to DVD1.)

•

To set the remote control back to DVD1, hold

down both (STOP) button and the 1 number

button on the remote control for at least ﬁve

seconds.

Also set the REMOT CODE on the FL menu to

the same setting as the remote control. (This

setting is set to DVD1 when the unit is shipped

from the factory.) (see page 34)

Getting Started

Load a disc.

Load a disc with the label side facing up, using the

disc tray guide to align the disc (if you’re loading

a double-sided DVD disc, load it with the side you

want to play face down).

Press (PLAY) to start playback.

If you are playing a DVD or Video CD, a menu may

appear (see page 17).

Note

•

For one-sided, two-layer discs containing movies, etc.,

there may be a short image stoppage at the point

where the layers change. This is not a malfunction.

^•Ba^Dsi^ec^pep^ndlⁱaⁿy^gb^ona^tc^hk^{e D}c^Vo^Dn^ot^rr^Vo^IDl^Es^{O CD, some}

operations may be different or restricted.

Button

What it does

Starts playback.

In title menu, it functions as the Enter

key.

Pauses a disc that’s playing.

Each time the button is pressed, a new

frame will appear.

Stops playback.

Skips to the start of the current track or

•

chapter, then to previous tracks/chapters.

Press and hold for Fast Reversed.

•

Skips to the next track or chapter.

Press and hold for Fast Forward.

•

Numbers

Playback starts from the selected track/

Resuming ^cp^hala^pty^erbⁿa^umc^bk^er.from the last

ENTER

Select the current menu option.

stopped point

This DVD system is able to resume disc

playback from its last stopped point (only

possible for the last 10 discs that were

recorded without a menu).

Playing discs

The basic playback controls for playing

discs are covered here. Further functions

are detailed in the next chapter.

Load one of the last 10 discs played.

Note

While “LOADING” appears on the display

•

Throughout this manual, the term “DVD” means

DVD-Video, and DVD R/RW. If a function is speciﬁc

to a particular kind of DVD disc, it is speciﬁed.

start playback from

panel, press PLAY to

the last stop point.

Switch the player on.

To cancel the resume mode

If you are playing a DVD or Video CD, also turn on

•

your TV and make sure that it is set to the correct

Press twice.

video input.

Important

Press OPEN/CLOSE to open the disc tray.

While using the DVD playback controls, you may see

the

mark displayed on-screen. The

mark means

that the operation is not allowed by the player and

disc.

Getting Started

Navigating DVD disc menus

Many DVD discs contain menus. Sometimes

these are displayed automatically when you

start playback; others only appear when you

press MENU or TOP-M.

Note

•

Some DVD-Audio discs feature a “Bonus Group”. To

access this group you have to input a password that

you can ﬁnd on the disc’s packaging (see page 36).

Button

What it does

TOP-M

Displays the “top menu” of a DVD disc. This

varies with the disc.

Displays a DVD disc menu—this varies with

the disc and may be the same as the “top

menu”.

RETURN

Returns to the previously displayed menu

screen.

Cursor

Moves the cursor around the screen.

Selects the current menu option.

2 3 5 ∞

(

)

ENTER

^NN^ua^mv^bi^eg^rsating Video CD PBC menus

Selects a numbered menu option

(some discs only).

Some Video CDs have menus from which you

can choose what you want to watch. These

are called PBC (Playback control) menus.

Press the MENU to turn the PBC function on

or off.

Note

•

Some discs don’t allow PBC menus.

Button

What it does

RETURN

Numbers

ENTER

Displays the PBC menu.

Selects a numbered menu option.

Selects the current menu option.

Displays the previous menu page

(if there is one).

Displays the next menu page

(if there is one).

Playing Discs

Preview function

DVD

Video-CD

SVCD

Press SCAN.

SVCD

VCD

SELECT DIGEST TYPE

TRACK DIGEST

DISC INTERVAL

TRACK INTERVAL

DVD-Video

SELECT DIGEST TYPE

TITLE DIGEST

CHAPTER DIGEST

TITLE INTERVAL

CHAPTER INTERVAL

DVD-Audio

SELECT DIGEST TYPE

GROUP DIGEST

TRACK DIGEST

GROUP INTERVAL

TRACK INTERVAL

5 ∞

Use the

keys to select one of the

following options and press ENTER.

This option is only available during playback mode.

•

TRACK/TITLE/CHAPTER/GROUP DIGEST

– View six different TRACK/TITLE/CHAPTER/

GROUP on one screen each time. This allows you

to have a quick glance at all the TRACK/TITLE/

CHAPTER/GROUP on the disc.

•

DISC/TITLE/GROUP INTERVAL – View the

whole disc in six thumbnail pictures. It divides

a disc into six portions at regular intervals and

displays them on one screen.

Introduction

• Many of the functions covered in this

chapter apply to DVD discs, Video CDs

and CDs, although the exact operation

of some varies slightly with the kind of

disc loaded.

TRACK/CHAPTER INTERVAL – View the

content of a single TRACK/CHAPTER in six

thumbnail pictures. It divides a single TRACK/

CHAPTER into six portions at regular intervals

and displays them on one screen.

• When playing DVD discs, if the icon

appears on-screen when you try to use

a particular function, either the player

or the disc doesn’t allow the use of that

function.

• When playing Video CDs, some of the

functions are not available in PBC mode.

If you want to use them, press the

MENU to turn the PBC function off (see

page 17).

2 3 5 ∞

• Use (

/ ) to select a track or

use the numeric buttons to enter the

selected track number.

Playing Discs

• To go to the previous or next page, press

4 ¢

• Press ENTER on the selected thumbnail

picture to start playback from there.

• To return to the main menu, select MENU

on the screen and press ENTER.

To exit the preview menu, select EXIT on

the screen and press ENTER.

For CD

• At stop mode, press SCAN on the remote

control. Each track will be played for a few

seconds.

Note

”

•

You can select “Track Interval only during playback

with PBC off.

Some discs don’t allow the Scan mode.

Playing Discs

Fast Forward/Fast Reverse

DVD

MP3

Super Audio CD Video-CD

DivX

WMA

The video images on DVD and VCD can be

viewed as a Fast Forward and Fast Reverse

with no sound.

In case of CD, the sound can be listened as a

Fast Forward and Fast Reverse with sound.

Viewing in Fast Forward/Fast Reversed

Press and hold

(NEXT) during play.

• Fast Forward is engaged.

• During Fast Forward, the speed of play

back can be adjusted from x2 speed to

x32 speed in 5 steps using

(NEXT).

Press and hold

(PREV) during play.

• Fast Reverse is engaged.

• During Fast Reverse, the speed of play

back can be adjusted from x2 speed to

x32 speed in 5 steps using

(PREV).

To return to normal play back press (PLAY)

to normal play back.

Note

•

The sound is muted during fast forward/reverse

scanning of DVD/VCD/Super Audio CD.

Playing Discs

Viewing a Paused Picture

Press (PAUSE).

Viewing slow playback

With this function, DVDs can be viewed in both forward

and reverse direction. Video CD can only be moved in

the forward direction.

∞

Press (down) during play.

•

Slow playback is engaged.

During slow playback, the speed of playback can be

adjusted from 1/2 normal playback speed to 1/16

normal playback

1/2 1/4 1/8 1/16

speed in 4 steps

∞

using (down).

Press (up) during play.

•

Slow playback in the reverse direction is engaged.

During slow playback, the speed of playback can be

adjusted from 1/2 normal playback speed to 1/16

normal playback

1/2 1/4 1/8 1/16

speed in 4 steps

using (up).

To return to normal playback

When the picture is paused or during slow playback,

^pfr^rea^sm^sine^gat⁽a^PLt^Ai^Ym⁾e^{restores normal playback operation.}

Step Motion playback: Viewing one

With this function, DVDs and Video CDs can only be

moved in the forward direction.

Press (PAUSE).

Each time the button is pressed, a new frame will

appear.

To return to normal playback

When viewing Step Motion playback, pressing (PLAY)

restores normal playback operation.

Note

•

There is no sound picture playback is paused or

during slow playback, or when advancing one frame

at a time.

Still Frame/Slow Play/Frame Advance

Playback

DVD-Video Video-CD

Pausing picture, slow play, or Step Motion playback

may not be possible with certain titles. In this case,

The video images on DVD and Video CD

can be viewed as a still frame, played back

at slow speeds and even advanced frame by

frame (Forward only).

the

mark is displayed.

•

A short sound may be noticeable when switching to

slow playback.

•

When you press the (PAUSE) button during slow

playback, it may advance a few frames past the

frame where you want it to stop.

Playing Discs

Using the page

DVD-Audio

Some DVD-Audio discs contain

information pages for photo galleries,

artist biographies, lyrics, etc.

Press the PAGE button on the remote

control during Playback. You may select the

image you want by moving the cursor button

2 3

(

Using the Repeat Play

DVD-Video DVD-Audio Super Audio CD Video-CD

MP3

JPEG

DivX

WMA

You can set the player to repeat individual

tracks on CDs or Video CDs, chapters or

titles on DVD discs, or the whole disc. It’s

also possible to loop a section of a disc.

You can’t use any repeat mode or looped

play with a Video CD playing in PBC mode.

Press REPEAT during playback to select a

repeat mode.

Each press switches the repeat mode:

DVD-Video

•

CHAPTER REPEAT

TITLE REPEAT

DISC REPEAT

OFF

DVD-Audio

•

TRACK REPEAT

GROUP REPEAT

DISC REPEAT

OFF

Video-CD

MP3

WMA

Super Audio CD

JPEG

DivX

•

TRACK REPEAT

DISC REPEAT

OFF

Note

•

Some discs don’t allow the Repeat function.

•

Any existing RANDOM or Repeat A-B mode will be

cancelled and Repeat mode will be activated.

Playing Discs

Looping a section of a disc

DVD

MP3

Super Audio CD Video-CD

DivX

WMA

Press A-B once at the start of the section

you want to repeat, then again at the end.

Playback immediately jumps back to the start point and

plays the loop round and round.

•

On a DVD disc, the start and end points of the

loop must be in the same title/chapter.

•

On a Video CD/CD disc, the start and end points

of the loop must be in the same track.

To resume normal playback, press A-B

again.

Note

•

There may be a slightly difference between point A

and the location where playback actually resumes

Us^din^epg^ent^dhⁱⁿe^gR^ona^tn^hd^eo^dim^sc.(SHUFFLE) Play

After Repeat A-B is exited, any existing Repeat or

RANDOM modes will be restored.

DVD

MP3

Super Audio CD Video-CD

DivX

WMA

JPEG

Use the random play function to play tracks

in a random order.

You can’t use random play with DVD-VR

mode or Video CD playing in PBC mode.

Press the RANDOM button during playback

to select a RANDOM (SHUFFLE) mode.

•

SHUFFLE

SHUFFLE REPEAT

SHUFFLE OFF

To cancel Random mode, press RANDOM.

Note

•

Any existing Repeat or Repeat A-B modes will be

cancelled and RANDOM mode will be activated.

•

If the disc currently playing is a CD layer of Super

Audio CD, CD layer of Super Audio CD will be

played.

•

For Hybrid Super Audio CDs, tracks on the Super

Audio CD layer are played by default.

Playing Discs

Switching Camera Angles

DVD-Video

Some DVD-Video discs feature scenes shot

from two or more angles. Check the disc box

for details: it should be marked with a

icon if it contains camera-angle scenes.

•

To switch the camera angle, press ANGLE.

Note

•

Depending on the disc, this feature may not work.

Switching the Subtitle Language

DVD-Video

DivX

Many DVD-Video discs or DivX discs have

subtitles in one or more languages. The

disc box will usually tell you which subtitle

languages are available. You can switch the

subtitle language at anytime during playback.

•

To display/switch the subtitle language,

press SUBTITLE repeatedly.

The current subtitle language is shown on-screen.

To set subtitle preferences, see page 50.

Note

•

In some cases, a subtitle can not be turned off even

if you select “OFF”.

Some discs allow you to change subtitles only via

the disc menu. In that case, press the MENU button

and change the settings.

Playing Discs

Switching the audio channel

Depending on the disc, this feature may not

work.

Video-CD

On Video CDs you can switch between

stereo, just the left channel, just the right

channel or Mixed Mono.

•

To switch the audio channel, press AUDIO

repeatedly.

The current playback channel(s) are indicated on-

^sla^cry^ee^enr^.

Switching Super Audio CD Playback

Super Audio CD

•

On a hybrid disc (with Super Audio CD and CD layers),

the player will always start playing the Super Audio CD

layer.

•

To switch between the Super Audio CD layer and the

CD player, press AUDIO while playback is stopped.

Switching Super Audio CD Playback

area

Super Audio CD

•

To Switch between the Super Audio CD multi-channel

^aU^nds^Sin^upg^ert^Ah^ue^diZ^{o C}o^Do^sm^terF^eoun^arc^eat^sio^byn^{pressing SOUND}

MODE.

DVD-Video DVD-Audio Video-CD

JPEG

During play or pause mode, press the

ZOOM button on the remote control to

zoom in x2, x3, x4, x1/2, x1/3, x1/4,

Normal in order for DVD-Video or VCD and

100%, 125%, 150%, 200%, Normal in

order for JPEG.

Switching the Audio Language

DVD-Video DVD-Audio

When playing a DVD-Video disc recorded

with dialog in two or more languages, you

can switch the audio language at anytime

during playback.

5 ∞ 2 3

Use the cursor buttons ( / /

) to

•

To display/switch the audio language, press

AUDIO repeatedly.

select the part of the screen you want to

The current audio language is shown on-screen.

zoom in on.

To set audio language preferences, see page

Note

50.

•

Zoom play cannot be used on some discs.

Zoom will not operate properly for some scenes.

Zooming may cause image deterioration or shaking.

Note

•

Depending on the disc, there are cases in which the

audio language cannot be switched during play. In

this case, make changes using the DVD menu.

It may take a few seconds till a selected Audio

Language is audible.

Playing Discs

Play back Information

This DVD system can display the disc

playback information (for example, title

or chapter number, elapsed playing time,

audio/subtitle language) and a number of

operations can be done without interrupting

disc playback.

DVD-Video Video-CD

During playback, press DISP.

•

A list of available disc information appears

on the TV.

DVD

TITLE

01/07

01/30

2CH

CHAPTER

AUDIO

ENG

SUBTITLE

BITRATE 00

OFF

TITLE ELAPSED 0:00:23

Video-CD

SVCD

TRACK

DISC TIME

01/01

1:01:14

TRACK TIME 1:01:14

REPEAT

OFF

BITRATE 75

TOTAL ELAPSED 0:00:20

Title/Chapter/Track selection

DVD-Video Video-CD

5 ∞

Press

to highlight “Title” / “Chapter”

or “Track”, then press ENTER to access.

Use the numeric keypad (0-9) to enter a

valid number (e.g. 04/05).

Audio/Subtitle

DVD-Video

5 ∞

Press

to highlight “Audio” or

to select one language, then

“Subtitle”, then press ENTER to access.

The Audio or Subtitle menu appears on the TV.

5 ∞

press ENTER to conﬁrm.

The current audio or subtitle language will be changed

to the selected language.

Playing Discs

Angle

Time Search

DVD-Video

DVD-Video Video-CD

5 ∞

Press

to highlight “Angle”, then press

Press

to highlight “TT Time”/“CH

ENTER to access.

Time”/“Disc Time” or “Track Time”, then

press ENTER to access.

Use the numeric keypad (0-9) to enter in a

valid number.

Use the numeric keypad (0-9) to enter a

valid time (e.g. 0:34:27).

Press ENTER to conﬁrm.

The playback skips to the chosen time.

Playback will go to the selected angle.

Note

Time Display

•

Some disc don’t allow the Time Search mode.

DVD-Video Video-CD

You can’t use Time Search mode with a Video CD

^•Repeat

playing in PBC mode.

5 ∞

Press

to highlight “Time Disp.”, then

press ENTER to access.

The following display types appear on the TV,

depending on the disc in the player.

DVD-Video Video-CD

5 ∞

Press

to highlight “REPEAT”, then

For DVD discs:

press ENTER to access.

TITLE Elapsed - elapsed playing time of current Title;

TITLE Remain - remaining playing time of current Title;

5 ∞

Press

to select the desired repeat

CHAPTER Elapsed - elapsed playing time of current

mode, then, press ENTER to access.

Chapter;

CHAPTER Remain - remaining playing time of current

Chapter;

For VCD/SVCD discs:

Total Elapsed - elapsed playing time of current Disc;

Total Remain - remaining playing time of current Disc;

Single Elapsed - elapsed playing time of current Track;

Single Remain - remaining playing time of current Track;

5 ∞

Press

to select the desired time

display mode, then press ENTER to display

the selected item.

Playing Discs

Group/Track Selection and time search

Time

DVD-Audio

Press DISPLAY (DISP.) repeatedly during

playback to change the displayed disc time

information.

Each time you press DISPLAY, the TV display

changes as follows.

GROUP 01/05 TRACK 01/15 0:10:00

TOTAL ELAPSED

SINGLE REMAIN

TOTAL REMAIN

SINGLE ELAPSED

GROUP 01/05 TRACK --/15

GROUP 01/05 TIME -/--/--

TRACK 01/15 TIME -/--/--

5 ∞

Press

to select the Track, Group Time

or Track time.

Use the numeric keypad (0-9) to enter a

valid number.

EX: Enter hours, minutes and seconds from

left to right.

Press ENTER to conﬁrm.

Note

•

When searching for a time in a group/ track, if

you enter a time outside the total time for the

group/track currently being played back,

INVALID is displayed.

INPUT

Playing Discs

Insert a disc.

•

The disc reading time may exceed 30

seconds due to the complexity of the

directory ﬁle conﬁguration.

•

The disc menu appears on the TV.

•

Playback will start automatically. If not,

press (PLAY).

00:00

001/014

MP3_files

MP3_MUSIC_1

MP3_MUSIC_2

MP3_MUSIC_3

If the disc main menu contains various

5 ∞

folders, use the

keys to select a

desired folder and press ENTER to open

the folder.

5 ∞

Use the

keys to select a track/ﬁle and

press ENTER to start playback.

•

Playback will start from the selected ﬁle

and continue through to the end of the

folder.

During playback, you can;

•

4 ¢

Press

to playback another

track/ﬁle in the current folder.

•

To select another folder from the current

disc, press to return to the root menu.

5 ∞

Use the

keys to make your selection

and press ENTER to conﬁrm.

Press REPEAT repeatedly to access

various play modes.

•

OFF

TRACK REPEAT: One ﬁle will be played

repeatedly.

•

DISC REPEAT: All ﬁles in one folder will be

played repeatedly.

Tip

•

To skip the folders menu when you load a MP3/

JPEG disc, set the MP3/JPEG NAV setting in the

Preference Setup Page to WITHOUT MENU.

Playing an MP3/DivX/JPEG/

™

Windows Media Audio disc

This DVD system can playback most of the

Note

™

MP3, JPEG and Windows Media Audio ﬁles

Some discs cannot be played on this player due to

recorded on a CD-R/RW disc or commercial

CD.

the conﬁguration and characteristics of the disc,

or due to the condition of recording and authoring

software that was used.

Playing Discs

4 ¢

Press

to display the other pictures

on the previous/next page.

2 3 5 ∞

Use the

keys to highlight one

of the pictures and press ENTER to start

playback.

Press the MENU to return to Picture CD

menu.

Zoom picture

During playback, press ZOOM repeatedly

to select a different zoom factor.

2 3 5 ∞

Use the

keys to pan through the

zoomed image.

Tip

•

This feature is not applicable for DivX discs.

•

Zoom play cannot be used on some discs.

Rotating/ﬂipping the picture

•

2 3 5 ∞

During playback, use the

keys

to rotate/ﬂip the picture on the TV.

∞

: Flip the picture vertically

: Flip the picture horizontally

: Rotate the picture counter-clockwise

: Rotate the picture clockwise

Note

•

Rotate and Flip operations are not supported on

DVD-Audio disc.

Playing a JPEG image ﬁle (slide show)

Scan Effect

•

Insert a Picture disc (Kodak Picture CD,

JPEG).

•

Press ANGLE repeatedly to choose a scan effect.

•

Various scan effects appear in the top left corner of

the TV screen.

For a Kodak disc, the slide show will begin

automatically.

For a JPEG disc, the picture menu will appear on the

Note

TV. Press PLAY to start the slide-show playback.

Supported ﬁle format:

Note

•

The ﬁle extension has to be “*.JPG” and not “*.JPEG”.

Some discs don't allow the Picture menu.

It can only display DCF-standard still pictures

or JPEG pictures e.g. TIFF. It cannot play back

Preview function

moving pictures, Motion JPEG and other formats,

or pictures in formats other than JPEG, or pictures

associated with sound.

During playback, press

• 12 thumbnail pictures will be displayed on

•

It may require longer time for the DVD system to

the TV.

display the disc content on the TV due to the large

number of songs/pictures compiled into one disc.

Playing Discs

Playing MP3/WMA music and JPEG

pictures simultaneously

You can create a musical slide show if the

disc contains both the MP3/WMA music and

JPEG picture ﬁles.

Insert an MP3/WMA disc that contains

music and pictures.

Select an MP3/WMA track in the menu and

press PLAY to start playback.

During MP3/WMA music playback, use the

2 3 5 ∞

keys to select a picture folder

from the disc menu and press PLAY

• The picture ﬁles will be played back

through to the end of the folder.

To stop simultaneous playback, press

STOP

Tip

•

It is normal to experience an occasional “skip” while

listening to your MP3 disc.

•

It is normal to experience an occasional pixelation

during MP3/DivX playback due to poor clarity of

digital contents during internet downloading.

•

Only the ﬁrst session of a multi-session CD will be

played back.

Playing Discs

Playing a DivX disc

This DVD system supports the playback of

DivX movies which you can copy from your

computer onto a CD-R/RW, DVD R/ RW

disc (see page 9 for more information).

Insert a DivX disc.

Press PLAY to start playback.

During playback, you can;

• If multilingual subtitles are embedded on

the DivX disc, you can press SUBTITLE

to change the subtitle language while

playing.

Tip

•

Subtitle ﬁles with the following ﬁle name extensions

(.srt, .smi, .sub, .ssa, .ass) are supported but do not

appear on the ﬁle navigation menu.

•

The subtitle ﬁle name has to be the same as the ﬁle

name of the movie.

The subtitle can only be displayed up to an average

of 42 characters.

The time search feature is not available during DivX

movie playback.

DivX compatibility information

•

Support for DivX 3.11, 4.x, 5.x.

Q-pel accurate motion compensation.

Global Motion Compensation (GMC) Playback.

Playing Discs

Using the Setup Menu

Before using the player, you should specify

the settings to be used in accordance with

the conditions under which the player is to

be used.

Note that once changed, the settings will be

saved and remain the same even after the

power has been turned off until the settings

are changed again.

The Setup menu gives you access to all the

player’s settings. Press SETUP to display/

leave the menu and the cursor and ENTER

buttons on the remote control to navigate

and select options.

Note

•

The language options shown in the on-screen

display illustrations on the following pages may not

correspond to those available in your country or

region.

Press the SETUP button on the remote

control. Select a tab using the cursor

2 3

buttons (

GENERAL SETUP: Setup of the GENERAL options

AUDIO SETUP: Setup of the audio options

VIDEO SETUP: Setup of the display and HDMI

Video options

PREFERENCE: Setup of the language, parental, and

⁄

several other options.

5 ∞

Use the cursor buttons ( / ) on the

remote control to access the different

features.

Press the ENTER button as many times as

necessary to select the desired option.

To make the setup screen disappear after

setting up, press the SETUP button again.

Note

•

Depending on the disc, some Setup Menu

selections may not work.

•

Some settings can not be selected during

playback and RESUME mode of DVD-Video.

In that case, press the (STOP) button once or

twice to stop playback completely.

DVD Setup Menu

Using the FL menu

The FL menu has been designed to set

"REMOTE CODE".

It can be set during stand by mode.

If a Disc had been loaded, press Power

button on the Remote Control to stand by

mode.

Selecting the FL menu

Press SET UP for longer than 2 sec.

Stand by LED is disappeared and "REMOTE

CODE" is displayed in the FL display.

REMOTE_CODE

•

If press ENTER, current status is displayed.

DVD_1

5 ∞

Use the cursor buttons ( / ) to select the

type of REMOTE CODE you want to set as

follows.

DVD 1

DVD 2

Press ENTER you want to set.

•

Press SET UP for longer than 2 sec to close the FL

menu and then go back to standby mode.

Note

•

The DVD player support two remote control codes:

DVD 1 and DVD 2.

Set the remote control code of the Remote Control

to the same setting. (page 15)

DVD Setup Menu

A black dot ( ) indicates the default setting

* It can be set only during STOP.

Page

OSD LANGUAGE ꢀENGLISH ESPANOL FRANCAIS

PLAYER MODE

DIVX(R) VOD CODE

DISC LOCK *

DISPLAY DIM

PROGRAM *

ꢀDVD AUDIO DVD VIDEO

LOCK ꢀUNLOCK

GENERAL

SETUP

ꢀ100% 70% 40%

INPUT MENU

ꢀON OFF

SCREEN SAVER

SLEEP

15 MINS 30 MINS 45 MINS 60 MINS ꢀOFF

ꢀON OFF

AUTO STANDBY

Page

AUDIO OUT

2 CHANNEL VIRTUAL SURROUND ꢀ5.1 CHANNEL

DIGITAL AUDIO

DIGITAL OUT

OFF ꢀALL PCM

LPCM OUT

ꢀ48KHZ 96KHZ

HDMI AUDIO OUT

ꢀAUTO MULTI PCM 2CH PCM OFF

SPEAKER SETUP PAGE

SPEAKER SETUP

FRONT L/R

ꢀLARGE SMALL

CENTER

OFF ꢀLARGE SMALL

REAR LS/RS

OFF ꢀLARGE SMALL

AUDIO SETUP

LFE(SUBWOOFER) ꢀON OFF

SPEAKER LEVEL

FRONT LEFT FRONT RIGHT CENTER LFE REAR LEFT

REAR RIGHT

SPEAKER DISTANCE

FRONT LEFT FRONT RIGHT CENTER LFE REAR LEFT

REAR RIGHT

ꢀOFF 88.2KHZ(X2) 176.4KHZ(X4)

ON ꢀOFF

CD UPSAMPLING

AUDIO DRC

Page

TV SYSTEM

PAL NTSC MULTI

TV ASPECT

4:3 PAN SCAN 4:3 LETTER BOX ꢀ16:9 WIDE

ꢀOFF ON

PROGRESSIVE

PICTURE SETTING

ꢀSTANDARD BRIGHT SOFT

PERSONAL BRIGHTNESS SHARPNESS CONTRAST TINT

COLOR

ADV PICTURE

DCDI

OFF ꢀON

GAMMA

VIDEO SETUP

PREFERENCE

CHROMA DELAY

PSCAN FORMAT

HDMI VIDEO

SUPER WIDE 16:9 SQUEEZE ꢀOFF

480P 576P 720P 1080I 1080P

ꢀAUTO

DYNAMIC PICTURE

DVI OUTPUT RANGE ENHANCED ꢀSTANDARD

YCbCr ꢀRGB

COMPONENT

BLACK LEVEL

7. 5 IRE 0 IRE

ON ꢀOFF

CLOSED CAPTION

Page

AUDIO

ꢀENGLISH CHINESE (SIMP) FRENCH SPANISH etc.

SUBTITLE

DISC MENU

PARENTAL

ꢀOFF ENGLISH CHINESE (SIMP) FRENCH SPANISH etc.

ꢀENGLISH CHINESE (SIMP) FRENCH SPANISH etc.

1 KID SAFE 2 G 3 PG 4 PG13 5 PGR 6 R 7 NC17

ꢀ8 ADULT

PBC

ꢀON OFF

MP3/JPEG NAV

VR LIST

WITH MENU ꢀWITHOUT MENU

ꢀORIGINAL LIST PLAY LIST

CHANGE

PASSWORD

DIVX SUBTITLE

DEFAULT

ꢀSTANDARD CYRILLIC

RESET

DVD Setup Menu

5 ∞

Use the cursor buttons ( / ) to select the

desired item, then press the cursor ( ) or

ENTER button.

GENERAL SETUP PAGE

OSD LANGUAGE

PLAYER MODE

DIVX(R) VOD CODE

DISC LOCK

DISPLAY DIM

PROGRAM

SCREEN SAVER

SLEEP

AUTO STANDBY

Note

•

Press to go back to the previous menu item.

Press SETUP to exit the menu.

OSD LANGUAGE

The language options are different

depending on your country or region, and

may not match the illustrations shown in the

user manual.

• Default setting: ENGLISH

The OSD (On-Screen Display) language for

this DVD system will remain as you have set

it, regardless of the changes made to the

DVD disc language.

Selects the preferred language for the DVD

system on-screen display menu.

PLAYER MODE

• Default setting: DVD AUDIO

•

DVD Audio

Should be selected when the player is to be used as

a DVD audio player.

DVD Video

Should be selected when the player is to be used as

a DVD video player.

Note

•

Some DVD-Audio discs contain bonus groups that

are accessible by a four-digit password. In this case,

consult the disc jacket and other packaging for

information.

During play, press DISPLAY twice.

•

The group and track list is displayed on the TV

Setting up the GENERAL SETUP page

Press the SETUP button.

screen.

2 3

Press

to select a bonus group, then press

⁄

ENTER.

Enter a four-digit password using the numeric

Select GENERAL SETUP PAGE using the

keypad (0-9), then press ENTER.

2 3

cursor buttons (

ENTER button.

), then press the

Set will start to playback the bonus group.

DVD Setup Menu

DivX(R) VOD CODE

PROGRAM

DVD-Video DVD-Audio Video-CD

MARANTZ provides you with the DivX VOD

(Video On Demand) registration code that

You can play the contents of the disc in the

order you want by programming the playing

order of the tracks. You can store up to 20

tracks.

allows you to rent and purchase videos using

the DivX VOD service. Press to see the

registration code and press ENTER to exit.

Use the registration code to purchase or

PROGRAM TT(07)/CH(- -)

rent the videos from the DivX VOD service

TT: CH:

at www.divx.com/vod. Follow the instructions

and copy the video from your computer onto

a CD-R/RW disc for playback on this DVD

system.

10 TT: CH:

Use the numeric keypad (0-9) to enter a

valid track/chapter number.

Note

information, visit us at www.divx.com /^®vod.

•

Any video the downloaded from DivX VOD can

only be played back on this DVD system. For more

2 3 5 ∞

Use the

keys to move the cursor

The time search function is not available during

to the next position.

DivX movie playback.

• If there are more than ten total

programme tracks, select NEXT on the

screen (or press

on the remote

DISC LOCK

control) and press ENTER to access the

• Default setting: UNLOCK

next programming page.

Not all discs are rated or coded by the disc

maker. You can prevent a speciﬁc disc from

playing by locking the disc. Up to 40 discs

can be locked.

To remove the track/chapter from the

programming menu, select the track/

chapter and press ENTER.

• LOCK – Selects this to block the playback

of the current disc. Subsequent access to

a locked disc requires a six-digit password.

The default password is “111111 ”.

Once complete, select START on the screen

and press ENTER to start playback.

• Playback will start from the selected track

• UNLOCK – All discs can be played.

under the programmed sequence.

To exit the programme menu, select EXIT in

DISPLAY DIM

the menu and press ENTER.

• Default setting: 100%

Selects the brightness of the DVD system

display panel.

Note

•

On Super Audio CD discs, you can program tracks

on the CD layer.

• 100% – Full brightness.

• 70% – Medium brightness.

• 40% – Dimmest display.

When playing back to program, previous RANDOM

and repeat modes are all cancelled.

When in VCD 2.0 mode (PBC ON mode), this

function does not work.

•

DVD-VR can not be programmed.

DVD-Audio Bonus Group/Tracks can not be

programmed.

DVD Setup Menu

SCREEN SAVER

• Default setting: ON

The screen saver prevents damage to the TV

screen by avoiding exposure to a static image

for too long.

• ON – Switches to TV screen saver mode

when playback has been stopped or

paused for more than 15 minutes.

• OFF – Turns off the screen saver function.

SLEEP

• Default setting: OFF

This feature automatically sets the DVD

player in standby mode after the period you

set has elapsed.

You can select from 15, 30, 45, and 60

minutes. Select OFF to cancel the sleep timer

function.

Press ENTER to conﬁrm your selection.

AUTO STANDBY

•

Default setting: ON

If ON is selected, the standby mode is

automatically selected to save power if the

player is left in the Stop mode for about 30

minutes.

DVD Setup Menu

5 ∞

Use the cursor buttons ( / ) to select the

desired item, then press the cursor ( ) or

ENTER button.

AUDIO SETUP PAGE

AUDIO OUT

DIGITAL AUDIO

HDMI AUDIO OUT

CD UPSAMPLING

AUDIO DRC

Note

Press to go back to the previous menu item.

^•AUDIO OUT

Press SETUP to exit the menu.

If you connected this player to your ampliﬁer

using the 5.1 channel analog outputs (front,

surround, center and subwoofer outs), set

this to 5.1 Channel; if you connected only

the stereo outputs, set to 2 Channel.

• Default setting: 5.1 CHANNEL

• 2 CHANNEL – Select this to change

the channel output to stereo, which

only delivers sound from the two front

speakers and a subwoofer.

• VIRTUAL SURR – Select this to virtually

reproduce the surround channels.

• 5.1 CHANNEL – Select this setting

when using a multichannel audio/(video)

receiver with 6 channel inputs. In this

mode, the player performs DTS decoding

or Dolby Digital 5.1-channel decoding

when applicable, and Dolby Pro Logic

decoding on DVD-Video, Video-CD and

Audio CD discs with 2-channel sound

tracks. No Dolby Pro Logic decoding is

done with Super Audio CD discs.

Note

•

You can also select it using the SOUND MODE

buttons on the remote control.

Some DVD-Audio discs don’t allow downmixing of

audio.

Setting up the AUDIO SETUP page

Press the SETUP button.

Select AUDIO SETUP PAGE using the cursor

2 3

buttons (

), then press the ENTER

button.

DVD Setup Menu

About source audio output

When the source output mode has been switched among 2CH, Virtual Surround and 5.1 CH

mode setting using the Audio Out setting, audio output for each source will be as shown in the

following table.

Audio Contents

Audio Out Setting

2 CH

Mixed 2ch output

5.1CH output

2ch L/R

Digital output

2ch L/R

Dolby Digital

PCM (Digital out is PCM)

Virtual Surround

2ch L/R

2ch+Vsurround

(2CH)

Bitstream (Digital out is All)

5.1 CH

2 CH

2ch L/R

Dolby Pro Logic II

Mixed 2ch (L0/R0)

Mixed 2ch+Vsurround

Mixed 2ch (L0/R0)

PCM Mixed 2CH

Dolby Digital

Virtual Surround

Mixed 2ch (Lt/Rt)

(Digital out is set to PCM)

(Multi CH)

Bitstream (Digital out is set to All)

5.1 CH

2 CH

Mixed 2ch (Lt/Rt)

Multi CH

2ch L/R

PCM 2ch 44.1/48KHz

LPCM

Virtual Surround

2ch L/R

2ch+Vsurround

(88.2/96KHz if LPCM OUT is set

(2CH)

to 96KHz.)

5.1 CH

2 CH

2ch L/R

Dolby Pro Logic II

2ch L/R

DTS, DVD-

Video/Audio

(2CH), CD

PCM (Digital out is PCM)

Bitstream (Digital out is All)

Virtual Surround

2ch+Vsurround

5.1 CH

2 CH

2ch L/R

DVD

Mixed 2ch (L0/R0)

Mixed 2ch (Lt/Rt)

Mixed 2ch (L0/R0)

Mixed 2ch+Vsurround

PCM Mixed 2CH

DTS,

Virtual Surround

(Digital out is set to PCM)

DVD-Audio

(Multi)

Bitstream (Digital out is set to All)

5.1 CH

2 CH

Mixed 2ch (Lt/Rt)

Mixed 2ch (L0/R0)

Mixed 2ch (Lt/Rt)

Multi CH

Mixed 2ch (L0/R0)

Mixed 2ch+Vsurround

MPEG

PCM (Digital out is PCM)

Virtual Surround

(MULTI)

Bitstream (Digital out is All)

5.1 CH

2 CH

Mixed 2ch (Lt/Rt)

Multi CH

2ch L/R

DVD-Audio

PCM 2CH

Virtual Surround

2ch L/R

(see page 42)

(2CH)

5.1 CH

2 CH

2ch L/R

2ch (Lf/Rf)

DVD-Audio

(Multi)

PCM 2ch (Lf/Rf)

Virtual Surround

2ch (Lf/Rf)+Vsurround

(see page 42)

5.1 CH

2 CH

2ch (Lf/Rf)

2ch L/R

Multi CH

2ch L/R

Virtual Surround

2ch L/R

2ch+Vsurround

PCM 2ch 44.1KHz

5.1 CH

2 CH

2ch L/R

---

Dolby Pro Logic II

2ch L/R

OFF

2ch

Multi

Virtual Surround

---

OFF

Super

Audio

5.1 CH

---

OFF

2 CH

---

OFF

Virtual Surround

5.1 CH

---

Mixed 2ch (Lt/Rt)

2ch L/R

2ch+Vsurround

Mixed 2ch

2ch L/R

Multi CH

2ch L/R

OFF

2 CH

PCM 2ch 44.1KHz

PCM 2ch 44.1KHz + Vsurround

PCM 2ch 44.1KHz

Video CD

Virtual Surround

5.1 CH

2ch+Vsurround

Dolby Pro Logic II

2ch L/R

S-Video CD 2ch

MP3/DivX,WMA

2 CH

Virtual Surround

2ch+Vsurround

Dolby Pro Logic II

PCM 2CH

5.1 CH

Note

•

No Dolby Pro Logic II is allowed on DTS, DVD-Audio and Super Audio CD audio track.

LFE (Subwoofer) will always carry the LFE channel.

DVD Setup Menu

DIGITAL OUT

HDMI AUDIO OUT

• Default setting: ALL

• Default setting: AUTO

Set the Digital output according to your

• AUTO – In this mode, when discs

optional audio equipment connection.

recorded in Dolby Digital, DTS, or MPEG

are played, the respective bit stream signal

is output. When DVD-Video/DVD-Audio

discs with multi-channel audio are played,

the multi-channel signal is output. When

discs recorded in 2-channel PCM or other

2-channel format are played, the audio

• OFF – Turn off the digital output.

• ALL – If you have connected your DIGITAL

AUDIO OUT to a multi-channel decoder/

receiver.

• PCM ONLY – Only if your receiver is not

capable of decoding multi-channel audio.

is output as 2-channel PCM. The output

formats are limited by the capabilities of

the connected component. For example,

if the disc is recorded in Dolby Digital

but the connected component does not

support Dolby Digital, the audio is output

as multi-channel PCM. If the connected

component does not support multi-

channel PCM either, the audio is output

as 2-channel PCM.

Note

•

If HDMI is activated, DIGITAL OUT is muted. HDMI

audio out is related to the “DIGITAL OUT” setting.

If set the “ALL” is set, HDMI Audio out is follows the

EDID. If set the “PCM” is set, HDMI Audio out is

always PCM.

•

If you set to “ALL” with a non-DTS compatible

ampliﬁer, noise will be output when you play a DTS

disc.

•

Some DVD-Audio discs prohibit digital audio out

• Multi PCM – In this mode, when discs

recorded in Dolby Digital, DTS, MPEG,

or DVD-Video/DVD-Audio are played,

due to copy protection.

No digital audio is output when playing Super

Audio CD.

a multi-channel signal is output. When

discs recorded in 2-channel PCM or other

2-channel format are played, the audio

is output as 2-channel PCM. The output

formats are limited by the capabilities of

the connected component. For example,

if the disc is recorded in Dolby Digital

but the connected component does not

support Dolby Digital, the audio is output

as 2-channel PCM.

LPCM OUT

• Default setting: 48kHz

If you connect the DVD Player to a PCM

compatible receiver via digital terminals,

coaxial or optical, you may need to adjust

“LPCM Output”. Discs are recorded at

a certain sampling rate. The higher the

sampling rate, the better the sound quality.

• 2ch PCM – In this mode, audio is output

as 2-channel PCM for all discs. Select this

mode when the unit is connected to a TV

or projector.

• 48kHz – Playback a disc recorded at the

sampling rate of 48 kHz. A 96 kHz (if

available on disc) PCM data stream will be

converted to 48 kHz.

• Off – Audio signals are not output from

the HDMI jack.

• 96kHz – Playback a disc recorded at the

sampling rate of 96 kHz. If the 96 kHz

disc is copy-protected, the digital output

will automatically be converted to a

sampling rate of 48 kHz.

Note

•

When audio signals are being output by HDMI-

compatible components, digital output signals are

muted.

•

If HDMI is activated, DIGITAL OUT is muted. HDMI

audio out is related to the “DIGITAL OUT” setting.

If set to “ALL”, HDMI Audio out is follows the EDID.

If set to “PCM”, HDMI Audio out is always PCM.

Note

•

High sampling rate DVD-Audio discs (192 kHz or

176.4 kHz) always output audio that has been

down sampled to 96 kHz or 88.2 kHz through the

digital outputs, when LPCM OUT is set to 96 kHz.

•

Audio is not output when the player is connected

to a device with an HDCP-compatible DVI jack.

Audio signals are not output from DVD-Audio

discs with CPPM copyright protection when using

components that do not support HDMI standard

Ver. 1.1.

•

Multi-channel and stereo audio is not output from

Super Audio CDs.

DVD Setup Menu

HDMI Audio Output

HDMI Setting (Audio)

Auto formats

Auto*

Multi PCM*

2 ch PCM

Off

Dolby Digital

Multi channel PCM

Left/Right

2 Channel DOWNMIX

2 Channel DOWNMIX*

Not Output

DVD

Linear PCM

Multi channel PCM

DTS

DVD-Audio

Multi channel PCM

CD/MP3/Super Audio CD*

DTS CD

DTS

Multi channel PCM

Left/Right

2 Channel DOWNMIX

Video CD

* : The order of priority in Auto mode is: Bit Stream, Multi PCM, 2ch PCM.

The output format is limited by the capabilities of the connected component.

* : The order of priority in Multi PCM mode is: Multi PCM, 2ch PCM.

The output format is limited by the capabilities of the connected component.

* : Audio is not output from discs that prohibit downmixing.

* : Audio is not output from Super Audio CDs. Audio is only output when a CD layer is played.

SPEAKER LEVEL

SPEAKER SET UP

Volume level setting for individual speakers

You can adjust the delay times (for center

(–6 dB to +6 dB).

and surround speakers only) and the

volume level for individual speakers. These

adjustments let you optimize the sound of

your system to best suit your surroundings

and setup.

SPEAKERS LEVEL SETUP

FRONT LEFT

FRONT RIGHT

CENTER

LFE

REAR LEFT

REAR RIGHT

0dB

IMPORTANT

•

Speaker settings are only available for multi-channel

audio output.

Note

FRONT SPEAKER, CENTER SPEAKER,

•

When set to 0 dB, the Audio Out level is 2 Vrms.

REAR SP

• OFF (only for CENTER and REAR

When set to higher than 0 dB, the Audio Out level

of other channels falls.

speakers) – Select when no speakers are

connected.

•

When set to lower than 0 dB, the Audio Out level

of the relevant channel falls.

• LARGE – Select if the main speaker cone

EX:

is 12 cm or more.

FRONT

0 dB

+6 dB

-6 dB

• SMALL – Select if the main speaker cone

2 Vrms

1 Vrms

LEFT

is less than 12 cm.

Other

2 Vrms

1 Vrms

2 Vrms

LFE (SUBWOOFER)

• ON – Select when a subwoofer is

connected.

• OFF – Select when no subwoofer is

connected.

DVD Setup Menu

SPEAKER DISTANCE

AUDIO DRC

Delay time settings in relation to the listening

position/distance for individual speakers (1.0

MS to 9.0 MS).

• Default setting: OFF

This mode optimizes playback of sound at

low volume. High volume outputs will be

softened and low volume outputs will be

enhanced to an audible level. This feature

is only applicable for DVD video discs with

Dolby Digital mode.

SPEAKERS DISTANCE SETUP

FRONT LEFT

FRONT RIGHT

CENTER

LFE

REAR LEFT

REAR RIGHT

3.0M

• ON – Turns on AUDIO DRC mode.

• OFF – Turns off AUDIO DRC mode.

Select this to enjoy the sound with its full

dynamic range.

Note

•

Use a longer delay time setting when the surround

speakers are closer to the listener than the front

speakers.

•

Audio DRC is only effective with Dolby Digital

Audio sources.

A test tone will be automatically generated to help

you judge the sound level of each

speaker.

CD UPSAMPLING

• Default setting: OFF

This feature allows you to convert your

music CD to a higher sampling rate using

sophisticated digital signal processing for

better sound quality. If you have activated

the upsampling function, the player will

automatically switch to stereo mode.

• OFF – Select this to disable CD

upsampling.

• 88.2kHz (X2) – Select this to convert

the sampling rate of CDs to twice that of

the original.

• 176.4kHz (X4) – Select this to convert

the sampling rate of CDs to four times

that of the original.

Note

•

This setting is only valid for signals output from the

analog jacks.

CD upsampling is switched to OFF, if AUDIO OUT

is set to Vsurround and 5.1CH.

AUDIO OUT is switched to 2CH, if CD upsampling

is set to 88.2 kHz or 176.4 kHz.

DVD Setup Menu

Setting up the VIDEO SETUP page

Press the SETUP button.

Select VIDEO SETUP PAGE using the cursor

2 3

buttons (

), then press the ENTER

button.

5 ∞

Use the cursor buttons ( / ) to select the

desired item, then press the cursor ( ) or

ENTER button.

VIDEO SETUP PAGE

TV SYSTEM

TV ASPECT

PROGRESSIVE

PICTURE SETTING

HDMI SETUP

COMPONENT

BLACK LEVEL

CLOSED CAPTION

Note

to go back to the previous menu item.

^•TV^PS^reY^ssSTEM

Press SETUP to exit the menu.

• Default setting: NTSC (USA model)

PAL (Europe model)

The colour system of the DVD system,

DVD and TV should match: only then will it

be possible to play a DVD on this system.

Before changing the TV system, determine

the colour system of your TV.

• PAL – Select this if the connected TV has

the PAL colour system. It will change the

video signal of an NTSC disc and output

it to PAL format.

• NTSC – Select this if the connected

TV has the NTSC colour system. It will

change the video signal of a PAL disc and

output it to NTSC format.

• MULTI – Select this if the connected TV

is compatible with both NTSC and PAL

(multi-system). The output format will be

in accordance with the video signal of the

disc.

Select one of the options and press ENTER

to conﬁrm.

• Follow the instructions shown on the TV

to conﬁrm the selection (if any).

• If a blank/distorted TV screen appears,

wait for 15 seconds for the auto recovery.

DVD Setup Menu

• 16:9 WIDE – Select this if you have a

CHANGING PAL TO NTSC

1.ENSURE THAT YOUR TV SYSTEM SUPPORTS

NTSC STANDARD.

2.IF THERE IS A DISTORTED PICTURE

DISPLAYED ON THE TV.WAIT IS SECONDS

FOR AUTO RECOVER

wide-screen TV.

CANCEL

Select one of the options and press ENTER

to conﬁrm.

Video output format when progressive is

"ON".

Note

^•PR^SO^omG^eR^dE^isS^csS^wIV^illE^{not allow you to change the aspect}

Disc

Output Format

ratio.

Format

system

YCbCr

Video/S-Video

NTSC

PAL

NTSC

PAL

PAL Progressive

NTSC NTSC Progressive

• Default setting: OFF

MULTI NTSC Progressive

PAL

PAL Progressive

Progressive scanning displays twice the

number of frames per second as interlaced

NTSC NTSC Progressive

PAL

MULTI PAL Progressive

PAL

scanning (ordinary normal TV system).

With nearly double the number of lines,

progressive scanning offers higher picture

resolution and quality.

If progressive is "OFF", Video Output Format

follow the TV SYSTEM with Interlace.

To change the TV system manually:

Press OPEN CLOSE to open the disc tray

Before you start...

without HDMI connected.

Ensure that you have connected this DVD

system to a progressive scan TV using the

YCbCr connection (see page 11 “Home

theater video connections”).

Press (RIGHT) on the remote control.

Press AUDIO on the remote control to change

the TV system setting.

PAL NTSC

NTSC PAL

• ON – Turns on progressive scan mode.

The instruction menu appears on the TV.

TV ASPECT

• Default setting: 16:9 WIDE

ACTIVATING PROGRESSIVE SCAN:

1. ENSURE YOUR TV HAS PROGRESSIVE SCAN.

2. CONNECT USING YPBPR (GBR) VIDEO CABLE.

3. IF THERE IS A DISTORTED PICTURE, WAIT

15 SECONDS FOR AUTO RECOVERY.

Set the aspect ratio of the DVD system

according to the TV type you have

connected. The format you select must be

CANCEL

available on the disc. If it is not, the setting

for TV display will not affect the picture

during playback.

Press to highlight “OK” in the menu and press

ENTER to conﬁrm.

• 4:3 PAN SCAN – Select this if you have

The picture on your TV will remain distorted in

this state until you turn on the progressive scan

mode on your TV.

a conventional

TV and want both

Turn on your TV's progressive scan mode

(refer to the user manual for your TV.)

The following menu appears on the TV.

sides of the picture

to be trimmed or

formatted to ﬁt your

TV.

CONFIRM AGAIN TO USE PROGRESSIVE

SCAN. IF PICTURE IS GOOD,

• 4:3 LETTER BOX – Select this if you have

PRESS OK BUTTON ON REMOTE.

a conventional TV. In this

case, a wide picture with

CANCEL

black bands on the upper

and lower portions of

the TV will be displayed.

DVD Setup Menu

Press to highlight OK in the menu and press

ADV PICTURE

ENTER to conﬁrm.

This player allows you to ﬁne-tune the

The set-up is complete now and you can start to

following video parameters.

enjoy the high quality picture.

We recommend setting the aspect ratio on

your TV if the function is available.

• OFF – Disables the progressive scan

mode.

To deactivate Progressive manually:

DCDi

Press OPEN CLOSE to open the disc tray

• Default setting: ON

without HDMI connected.

DCDi (Directional Correction Deinterlacing)

computes and tracks the angle of the screen

edge to ﬁll in missing pixels on the TV

Press (LEFT) on the remote control. Press

AUDIO on the remote control.

The DVD background screen appears on the TV.

screen. DCDi will optimize the image quality

signiﬁcantly, especially during slow motion

playback. This function is available only for

progressive scan output.

Tip

•

There are some progressive scan TVs and high-

deﬁnition TVs that are not fully compatible with

this unit, resulting in an unnatural picture when

playing back a DVD Video disc in the progressive

scan mode. In this case, turn off the progressive

scan feature on both the DVD system and your TV.

• OFF – Select to deactivate this function.

• ON – Select to activate this function.

GAMMA

Enables you to non-linearly adjust the intensity

of the picture. A positive value enables you to

bring out low level detail in dark scenes, while

a negative value emphasizes contrast. This

function is not available when using an HDMI

compatible component.

PICTURE SETTING

• Default setting: STANDARD

This DVD system provides three predeﬁned

sets of picture colour settings and one

personal setting which you can deﬁne

yourself.

-7 to +7

• STANDARD – Original colour setting.

• BRIGHT – Vibrant colour setting.

• SOFT – Warm colour setting.

CHROMA DELAY

The chroma (color) and luminance (brightness)

signals are not synchronized. The Chroma

Delay setting allows you to adjust the advance

delay of the chroma signal to yield a perfectly

clear picture. This function is not available

when using an HDMI-compatible component.

• PERSONAL – Selects this to personalize

2 3

the picture colour setting. Use the

keys to select to the setting that best

suits your personal preference and press

ENTER to conﬁrm. For an average setting,

select 0.

-3 to +3

• BRIGHTNESS – Increase the value to

PSCAN FORMAT

brighten the picture or vice versa.

• Default setting: OFF

• SHARPNESS – Increase the value to

Set the aspect ratio of the projected images on

the screen. This function is only available for

progressive scan and HDMI video output.

sharpen the picture or vice versa.

• CONTRAST – Increase the value to

sharpen the picture or vice versa.

• SUPER WIDE – Select this to display a

4:3 picture disc on a wide-screen TV with

non-linear stretching (the centre position

of the screen is stretched less than the

side).

• TINT – Increase the value to darken

the picture or vice versa.

• COLOR – Increase the value to

enhance the color in your picture or

vice versa.

• 16:9 SQUEEZE – Select this to display

a 4:3 picture disc on a widescreen TV

without stretching. Black bars will be

shown on the both sides of the TV screen.

• OFF – No aspect ratio adjustment is

made when this option is selected.

DVD Setup Menu

HDMI VIDEO

• Default setting: AUTO

Selects a suitable video resolution depending on the capability of the connected TV/device to

enhance the HDMI video output.

• 480P – Progressive output in 480 lines for NTSC TV

• 576P – Progressive output in 576 lines for PAL TV

• 720P – Progressive output upscaled to 720 lines

• 1080i – Interlaced output upscaled to 1080 lines

• 1080P – Progressive output upscaled to 1080 lines

• AUTO – The video output will automatically follow the display’s supported resolution

Note

•

If no display appears on the TV due to an unsupported resolution, use the composite video cable to connect the

DVD system and your TV. Turn on your TV to the correct input channel for the composite video and adjust the

resolution setting to 480P/576P.

•

The resolution can also be set with the HDMI button on the front panel.

Pressing the HDMI button for three seconds or more toggle the HDMI on/off state (see pages 13, 14).

In general, the larger the number, the higher the resolution.

When the resolution is changed, the image may be corrupted or the output may take longer than normal.

720P/1080i/1080P only supports 60 Hz Video signal.

When 480P/576P has been selected, multi-channel PCM at sampling frequency of 96 kHz cannot be output if the

connected TV, projector, etc. is not compatible with WCLOCK. The multi-channel PCM is converted to 48 kHz/2ch

before being output.

DVD Setup Menu

Setup Examples

Video

HDMI output

Sink EDID

Disc

S-Video

YCbCr

TV Aspect

16 : 9 Wide

4:3 LB

PSCAN FORMAT

OFF

(Progressive:ON)

Format

4:3

16:9

(Progressive:OFF)

16 :9 SQUEEZE

SUPERWIDE

Dont' care

OFF

16:9

4:3 PS*

16 : 9 Wide

16 :9 SQUEEZE

SUPERWIDE

Dont' care

4:3

4:3 LB

4:3 PS

* : When actual video output is Pan-scan. ("TV Aspect" is 4:3panscan and disc permits Pan-scan.)

* : When actual video output is Letterbox. ("TV Aspect" is 4:3panscan but disc does NOT permit Pan-scan.)

Video Out format when HDMI is activated

YCbCr Output

HDMI Video

Video/S-Video output

Output

Progressive ON

Progressive OFF

480P

576P

720P

480P (NTSC progressive)

576P (PAL progressive)

Follow the Disc Source with Interlace.

(ex: NTSC disc play: NTSC interlace)

1080i

No Video

1080P

DVD Setup Menu

DYNAMIC PICTURE

BLACK LEVEL

Produces more dynamic picture by increasing

the picture contrast and the color intensity.

This function is available only for progressive

scan output.

• Default setting: 7.5 IRE (USA model)

0 IRE (European model)

If you set the TV type to NTSC, set the Black

level shift to 7.5 IRE. This will improve the

color contrast during playback. The black

0 to 5

level setting has no effect if the TV type is

set to PAL.

DVI OUTPUT RANGE

• Default setting: STANDARD

• 7. 5 IRE – Select this to enhance the black

level.

When connecting the DVI unit, black may

rise to the surface depending on the display.

• 0 IRE – Select this for the standard black

level setting.

• ENHANCED – Image data values between

0 (black) and 255 (white)

CLOSED CAPTION (USA Model only)

• STANDARD – Image data values between

• Default setting: OFF

16 (black) and 235 (white)

Closed captions are data hidden in the video

signals of speciﬁc discs, and are invisible

without the use of a special decoder. The

difference between subtitles and captions

is that subtitles are intended for hearing

persons and captions are for the hearing

impaired. Subtitles rarely show all of

COMPONENT

(Euro model only)

• Default setting: RGB

This setting allows you to toggle the output

of the video signal between RGB (on the A/V

EURO CONNECTOR) and YCbCr (on the

component).

the audio. For example, captions show

sound effects (e.g., “phone ringing” and

“footsteps”), while subtitles do not. Before

you select this function, please ensure that

the disc contains closed caption information

and your TV set also supports this function.

• YCbCr – Select this for YCbCr Pr

connection on component Video out.

• RGB – Select this for the A/V EURO

CONNECTOR.

• ON – Select this to enable the closed

To change the COMPONENT out manually:

caption function.

Press OPEN CLOSE to open the disc tray

• OFF – Select this to disable the closed

without HDMI connection.

caption function.

Press (RIGHT) on the remote control.

Press ANGLE on the remote control to change

the COMPONENT out.

Note

•

When the player is set to YCbCr, some TV may not

properly synchronize with the player on the A/V

EURO connector.

DVD Setup Menu

Setting up the PREFERENCE page

Press (STOP) twice to stop playback (if

any), then press SETUP.

Select PREFERENCE PAGE using the cursor

2 3

buttons (

), then press the ENTER

button.

5 ∞

Use the cursor buttons ( / ) to select the

desired item, then press the cursor ( ) or

ENTER button.

PREFERENCE PAGE

AUDIO

SUBTITLE

DISC MENU

PARENTAL

PBC

MP3/JPEG NAV

VR LIST

PASSWORD

DIVX SUBTITLE

DEFAULT

Note

•

to go back to the previous menu item.

Us^Pin^reg^ssthe AUDIO, SUBTITLE and DISC

Press SETUP to exit the menu.

MENU language

You can select your preferred language

settings for DVD playback. If the selected

language is recorded on the DVD disc, the

DVD system will automatically play the

disc in that language. Otherwise, the disc’s

default language will be used instead.

AUDIO

Selects the preferred audio language for

DVD playback.

• Default setting: ENGLISH

If the language you want is not in the list,

select OTHERS, then use the numeric

keypad (0-9) on the remote to enter the

4-digit language code “XXXX” (see page 54

“Language Codes”) and press ENTER.

SUBTITLE

Selects the preferred subtitle language for

DVD playback.

• Default setting: OFF

DVD Setup Menu

DISC MENU

PBC

Selects the preferred disc menu language for

DVD playback.

• Default setting: ON

The Play Back Control feature is applicable

• Default setting: ENGLISH

for VCD/SVCD only. It allows you to play

Video CDs (2.0) interactively, following the

menu on the display.

5 ∞

Use the

•

keys to select a language and

press ENTER to conﬁrm.

• ON – The index menu (if available) will

Note

appear on the TV when you load a VCD/

SVCD.

For some discs, selection can be made using the

PA^DR^VE^DN^mT^eA^nuL^{. In this case, press MENU to display the}

• OFF – The VCD/SVCD will skip the index

DVD menu screen and then make your selection.

menu and playback directly from the

beginning.

• Default setting: 8 ADULT

MP3/JPEG NAV

Some DVDs may have a parental level

assigned to the complete disc or to certain

scenes on the disc. This feature lets you set a

playback limitation level.

• Default setting: WITHOUT MENU

MP3/JPEG Navigator can only be set if the

disc is recorded with a menu. It allows you

to select different display menus for easy

navigation.

The rating levels are from 1 to 8 and are

country dependent. You can prohibit the

playing of certain discs that are not suitable

for your children or play certain discs with

alternative scenes for certain discs.

• WITHOUT MENU – Displays all the ﬁles

contained in the MP3/Picture disc.

• WITH MENU – Displays the folder menu

of the MP3/Picture disc.

Note

PREFERENCE PAGE

AUDIO

1 KID SAFE

2 G

•

This DVD system can only display 650 ﬁles/folder

SUBTITLE

DISC MENU

PARENTAL

PBC

MP3/JPEG NAV

VR LIST

in the directory.

3 PG

4 PG 13

5 PGR

6 R

VR LIST

PASSWORD

DIVX SUBTITLE

DEFAULT

7 NC 17

8 ADULT

• Default setting: ORIGINAL LIST

There are two ways to play back a disc in VR

5 ∞

Press

to highlight a rating level for the

(Video Recording) format: ORIGINAL LIST

disc inserted and press ENTER.

and PLAY LIST. This feature is not available

with non-VR format discs.

• To disable parental controls and have all

discs play, select 8 ADULT.

• ORIGINAL LIST – Select this to play the

originally recorded titles on the disc.

Use the numeric keypad (0-9) to enter the

• PLAY LIST – Select this to play the

edited version of the disc. This feature is

only available when a play list has been

created.

six-digit password (see page 52).

• DVDs that are rated above the level you

selected will not play unless you enter the

six-digit password.

Note

•

VCD, SVCD, and CD have no level indication, so the

parental control function has no effect with these

types of discs. This also applies to most illegal DVD

discs.

Some DVDs are not encoded with a rating even

though the movie rating may be printed on the disc

cover. The rating level feature does not work for

such discs.

DVD Setup Menu

Previewing VR format

PASSWORD

The password is used for both Parental

During playback, press SCAN.

Control and Disc Lock. Enter your six-digit

password to play a locked disc or when

prompted for a password. The default

password is “111111 ”. To change the password:

5 ∞

Press

to highlight either TITLE

DIGEST or TITLE INTERVAL.

SELECT DIGEST TYPE

TITLE DIGEST

Press ENTER to access the change password

menu.

TITLE INTERVAL

OLD PASSWORD

NEW PASSWORD

CONFIRM PWD

Press ENTER to select the function.

• TITLE DIGEST – This function will display

thumbnail pictures of titles on the screen.

Up to six thumbnail pictures per page will

be displayed.

• In ORIGINAL LIST mode, the originally

recorded titles on the disc will be

displayed.

Use the numeric keypad 0-9 on the remote

control to enter your existing six-digit

password at OLD PASSWORD.

• In PLAY LIST mode, every title in the

play list will be displayed.

Note

• TITLE INTERVAL – This function will

divide and display the contents of each

title being played back in regular intervals,

making it easy to preview the recording.

•

When doing this for the ﬁrst time or if you forget

your existing password, key in “111111 ”.

Enter the new six-digit password at NEW

PASSWORD.

Up to six thumbnail pictures per page will

be displayed.

Enter the new six-digit password again at

• If the title being played back is short,

CONFIRM PWD.

the TITLE DIGEST function will be

performed instead.

Press ENTER to conﬁrm and exit the menu.

DIVX SUBTITLE

You can set the font type that supports the

recorded DivX subtitle.

• Default setting: STANDARD

STANDARD

(example for 6 thumbnail pictures display)

Albanian, Danish, Dutch, English, Finnish, French,

Gaelic, German, Italian, Kurdish (Latin), Norwegian,

Portuguese, Spanish and Swedish.

2 3 5 ∞

Use

to select a title, or use the

numeric buttons to enter the title number

CYRILLIC

next to SELECT.

Bulgarian, Belorussian, Macedonian, Moldavian,

Russian, Serbian and Ukrainian.

4 ¢

• Press

to access the previous/

next page.

Note

Press ENTER to conﬁrm the selection.

•

Supported subtitle extensions for DivX are “.srt”,

“.smi”, “.sub”, “.ssa”, “.ass”.

To quit the preview function

2 3 5 ∞

•

Use

to highlight EXIT and press

ENTER to conﬁrm.

To return to the preview menu

2 3 5 ∞

•

Use

to highlight MENU and press

ENTER

to conﬁrm.

DVD Setup Menu

DEFAULT

This feature enables you to reset all the

setup menu options and your personal

settings to the factory defaults, except your

password for Parental Control and Disc Lock.

Press ENTER to conﬁrm the default reset.

Additional Information

Language Codes

This page is used to select other languages. This does not affect the options in AUDIO, SUBTITLE or

DISC MENU.

Abkhazian

6566

6565

6570

8381

6577

6582

7289

6583

6569

6589

6590

6665

6985

6669

6678

6672

6673

7866

6683

6682

6671

7789

6983

6765

6772

6769

7889

9072

9065

6785

6786

7587

6779

7282

6783

6865

7876

6890

6978

6979

6984

7079

7074

7073

7082

7089

7168

7176

7565

6869

7573

6976

7178

7185

7265

7269

7290

7273

7279

7285

7383

Oromo

7977

7983

8073

8065

7065

8076

8084

7967

8083

8185

8277

8279

8278

8285

8377

8371

8365

8367

7168

8382

8378

8368

8373

8375

8376

8379

8384

7882

6983

8385

8387

8383

8386

8476

8489

8471

8465

8484

8469

8472

6679

8473

8479

8483

8478

8482

8475

8487

8571

8575

8582

8590

8673

8679

8765

6789

8779

8872

8973

8979

9065

9085

Ido

7379

7368

7365

7369

7385

7375

7165

7384

7465

7486

7576

7578

7583

7575

7577

7573

8287

7589

7586

7579

7574

7585

7574

7679

7665

7686

7666

7673

7678

7684

7666

7775

7771

7783

7776

7784

7186

7773

7782

7772

7779

7778

7865

7886

7868

7882

7871

7869

8369

7868

7879

7866

7878

7889

7878

7967

6785

7982

Afar

Ossetian; Ossetic

Ossetic; Ossetian

Pali

Indonesian

Afrikaans

Interlingua (International)

Albanian

Interlingue

Amharic

Panjabi

Inuktitut

Arabic

Persian

Inupiaq

Armenian

Assamese

Avestan

Polish

Irish

Portuguese

Provençal; Occitan (post)

Pushto

Italian

Japanese

Aymara

Javanese

Azerbaijani

Bashkir

Quechua

Raeto-Romance

Romanian

Rundi

Kalaallisut

Kannada

Basque

Kashmiri

Belarusian

Kazakh

Bengali

Russian

Khmer

Bihari

Samoan

Kikuyu; Gikuyu

Kinyarwanda

Kirghiz

Bislma

Sango

Bokmål, Norwegian

Bosnian

Sanskrit

Sardinian

Scottish Gaelic; Gaelic

Serbian

Komi

Breton

Korean

Bulgarian

Kuanyama; Kwanyama

Burmese

Shona

Kurdish

Castilian, Spanish

Sindhi

Kwanyama; Kuanyama

Catalan

Sinhalese

Lao

Chamorro

Chechen

Slovak

Latin

Slovenian

Somali

Latvian

Chewa; Chichewa; Nyanja

Chichewa; Chewa; Nyanja

Chinese

Letzeburgesch;

Limburgan; Limburger;

Limburger; Kimburgan;

Limburgish; Limburger;

Lingala

Sotho, Southern

South Ndebele

Spanish; Castilian

Sundanese

Swahili

Chuang; Zhuang

Church Slavic; Slavonic;

Church Slavonic; Church

Chuvash

Lithuanian

Swati

Luxembourgish;

Macedonian

Malagasy

Cornish

Swedish

Corsican

Tagalog

Croatian

Tahitian

Malay

Czech

Tajik

Malayalam

Danish

Tamil

Maltese

Dutch

Tatar

Manx

Dzongkha

Telugu

Maori

English

Thai

Marathi

Esperanto

Tibetan

Marshallese

Estonian

Tigrinya

Moldavian

Faroese

Tonga (Tonga Islands)

Mongolian

Fijian

Tsonga

Nauru

Finnish

Tswana

Navaho; Navajo

Navajo; Navaho

Ndebele; North

Ndebele; South

Ndonga

French

Turkish

Frisian

Turkirnen

Twi

Gaelic; Scotish Gaelic

Gallegan

Uighur

Georgian

Ukrainian

Urdu

Nepali

German

Northern Sami

North Ndebele

Norwegian

Gikuyu; kikuyu

Greek,

Uzbek

Vietnamese

Guarani

Volapük

Norwegian Bokmål; Bokmål

Norwegian Nynork

Nyanja; Chichewa; Chewa

Nynorsk; Norwegian;

Occitan (post 1500); Proven

Old Bulgarian; Old Slavonic;

Old Church Slavonic; Old

Old Slavonic; Church

Oriya

Gujarati

Walloon

Hausa

Welsh

Hebrew

Wolof

Herero

Xhosa

Hindi

Yiddish

Hiri Motu

Hungarian

Icelandic

Yoruba

Zhuang; Chuang

Zulu

Additional Information

Handling discs

Discs to avoid

When holding discs of any type, take care not to leave

Discs spin at high speed inside the player. If you can see

ﬁngerprints, dirt or scratches on the disc surface. Hold

the disc by its edge or by the center hole and edge.

that a disc is cracked, chipped, warped, or otherwise

damaged, don't risk using it in your player. You could

end up damaging the unit.

Damaged or dirty discs can affect playback performance.

Take care also not to scratch the label side of the disc.

Although not as fragile as the recorded side, scratches

can still result in a disc becoming unusable.

This unit is designed for use with conventional, fully

circular discs only. Use of shaped discs is not recom-

mended for this product.

Should a disc become marked with ﬁngerprints, dust,

etc., clean using a soft, dry cloth, wiping the disc lightly

from the center to the outside edge as shown in the

diagram below.

Cleaning the pickup lens

The DVD player’s lens should not become dirty in normal

use, but if for some reason it should malfunction due to

dust or dirt, consult your nearest MARANTZ-authorized

service center. Although lens cleaners for CD players

Don’t wipe the disc surface

using circular strokes.

Wipe lightly from the

center of the disc using

straight strokes.

^aP^rr^eo^cob^mle^mm^ercs^iaw^llyi^at^vh^ailc^abo^len^,d^ween^dosa^not^tio^ren^{commend using}

them since some may damage the lens.

If necessary, use a cloth moistened in alcohol, or a

commercially available CD/DVD cleaning kit to clean a

disc more thoroughly. Never use benzene, thinner or

other cleaning agents, including products designed for

cleaning vinyl records.

Condensation may form inside the player if it is brought

into a warm room from outside, or if the temperature of

the room rises quickly. Although the condensation won’

t damage the player, it may temporarily impair its per-

formance. For this reason you should leave it to adjust

to the warmer temperature for about an hour before

switching on and using it.

Storing discs

Although CDs and DVD discs are more durable than

vinyl records, you should still take care to handle and

store discs correctly. When you're not using a disc,

return it to its case and store upright. Avoid leaving discs

in excessively cold, humid, or hot environments (including

under direct sunlight).

Don't glue paper or put stickers onto the disc, or use

a pencil, ball-point pen or other sharp-tipped writing

instrument. These could all damage the disc.

For more detailed care information, see the instructions

that come with discs.

Do not load more than one disc into the player.

Additional Information

ing a suitable location for it:

Hints on installation

Moving the player

If you need to move the player, ﬁrst press the POWER

^WeD^wao^nt..^y.^{ou to enjoy using this unit for years to come,}

so please bear in mind the following points when choos-

ON/OFF button on the front panel to turn the player

off, then unplug the power cord. Never lift or move the

unit during playback: discs rotate at high speed and may

be damaged.

Use in a well-ventilated room.

✓

Place on a solid, ﬂat, level surface, such as a table,

✓

Precautions on using the power cord

shelf or stereo rack.

Handle the power cord by the plug part. Do not pull

out the plug by tugging the cord, and never touch the

power cord when your hands are wet, as this could

cause a short circuit or electric shock. Do not place the

unit, a piece of furniture, or other object on the power

cord or pinch the cord in any other way. Never make a

knot in the cord or tie it with other cords. The power

Don’t...

Use in a place exposed to high temperatures or

✗

humidity, including near radiators and other heat-

generating appliances.

Place on a window sill or other place where the

✗

player will be exposed to direct sunlight.

cords should be routed so that they are not likely to

be stepped on. A damaged power cord can cause a ﬁre

or give you an electric shock. Check the power cord

once in a while. If you ﬁnd it damaged, ask your nearest

MARANTZ authorized service center or your dealer for

a replacement.

Use in an excessively dusty or damp environment.

✗

Place directly on top of an ampliﬁer, or other

✗

component in your stereo system that becomes

hot during use.

Use near a television or monitor as you may ex-

✗

perience interference, especially if the television

uses an indoor antenna.

Use in a kitchen or other room where the player

may be exposed to smoke or steam.

✗

Use on a thick rug or carpet, or cover with cloth:

this may prevent proper cooling of the unit.

Place on an unstable surface, or one that is not

large enough to support all four of the unit’s feet.

Additional Information

Troubleshooting

Settings are canceled.

Incorrect operation is often mistaken for

trouble or malfunction. If you think that

there is something wrong with this unit,

check the points below. Sometimes the

trouble may lie in another component.

•

When the power is cut due to a power failure or by

unplugging the power cord, settings will be canceled.

Before unplugging the power cord, press the POWER

button on the Remote Control and check that

STANDBY indicator on the front panel is lit, then

press POWER ON/OFF on the front panel to turn the

player off.

Inspect the other components and

electrical appliances being used. If

the trouble cannot be rectiﬁed after

checking the items below, ask your

nearest MARANTZ authorized service

center or your dealer to carry out repair

work.

No picture/No color.

•

Incorrect video connections.

Check that connections are correct and that plugs are

inserted fully.

TV/monitor or AV ampliﬁer settings are incorrect.

Check the instruction manual of the connected

equipment.

The disc is ejected automatically after loading.

The PROGRESSIVE menu is set to ON but your TV/

monitor is not compatible with progressive scan.

•

Dirty or damaged disc.

Reconnect the player to your TV using a composite

or S-Video cord and set the TV to the appropriate

input. Now choose the Interlace setting in the

See page 55 for disc care information.

Disc not seated properly in the disc guide.

Align the disc properly.

PROGRESSIVE menu, then switch the TV input back

to the component input. (page 45)

Incompatible region number.

If the region number on a DVD-Video disc does not

Screen is stretched or aspect does not change.

match the number on the player, the disc cannot be

used (page 9).

•

The TV ASPECT setting in the Setup menu is incorrect.

•

Condensation inside the player.

Set the TV ASPECT option to match the TV/monitor

you're using (page 45).

Allow time for condensation to evaporate. Avoid using

the player near an air-conditioning unit.

Picture disturbance during playback or dark.

Playback is not possible.

•

This player is compatible with Macro-Vision System copy

guard. Some discs include a copy prevention signal, and

when this type of disc is played back, stripes etc., may

•

Disc is loaded upside down.

Reload the disc with the label side face-up.

appear on some sections of the picture depending on the

TV. This is not a malfunction.

Cannot play DVD-R/RW disc.

Discs respond differently to particular player functions.

This may result in the screen becoming black for a brief

instant or shaking slightly when the function is executed.

•

Only a DVD-R/RW disc that has been ﬁnalized only can be

played.

These problems are largely due to differences between

mark appears on the screen.

discs and disc content and are not malfunctions of this

player.

•

The operation is prohibited by the player.

•

When using progressive-scan

•

The selected function does not operate for that disc.

If your TV is connected using the COMPONENT

VIDEO OUT jacks, set the PROGRESSIVE menu to

OFF (page 45).

Picture playback stops and the operation buttons can

not be used.

•

Press (STOP), then start playback again (PLAY).

When recorded on a VCR or passed through an AV

selector, there is disturbance in the playback picture.

Switch the power off once using the front panel POWER

ON/OFF and then switch on again using the front panel

POWER ON/OFF.

•

Due to the player’s copy protection circuits, connection

of this device through a VCR or an AV selector may

prevent recording or cause picture problems. This is not a

malfunction.

New settings made in the Setup screen menus while a

disc is playing are ineffective.

•

Some settings can be changed while a disc is playing, but

do not take effect until the disc is stopped then restarted.

This is not a malfunction.

Make the same setting when the player is stopped.

Press (STOP), then restart playback (PLAY).

Note that making settings in the Setup screen menus

may cancel the RESUME function.

Additional Information

The remote control doesn't seem to work.

Noticeable difference in DVD and CD volume.

•

The remote control is too far from the player, or the angle

with the remote sensor is too wide.

•

DVDs and CDs use different recording methods. This is

not a malfunction.

Use the remote control within its operating range (page

Cannot output 192 kHz or 176.4 kHz digital audio.

7).

The player does not output digital audio at these sampling

The batteries are exhausted.

rates.

Put in new batteries (page 7).

Cannot output 96 kHz or 88.2 kHz digital audio.

Cannot listen to high-sampling rate audio through the

•

Check that the LPCM OUT setting is not set to 48 kHz

digital output.

(page 41).

•

LPCM Out is set to 48 kHz.

•

Some discs are digital copy-protected and do not output

Set it to 96 kHz.

high sampling rate digital audio.

As a copy-protection measure, some DVDs do not output

96 kHz audio.

No DTS audio output.

In this case, even if 96 kHz is selected, the player

automatically outputs the audio at 48 kHz. This is not

a malfunction.

•

If this unit is connected to a non-DTS compatible ampliﬁer

or decoder using a digital audio cable, set DIGITAL OUT

to PCM in the Setup menu. If you do not do this, noise

will be output if you try and play a DTS disc.

No audio, or audio is distorted.

•

Some DVD discs do not output digital audio.

Switch your ampliﬁer to the player's analog outputs.

Dirt, dust, etc. on the disc.

If this unit is connected to a DTS-compatible ampliﬁer or

decoder using a digital audio cable, check the ampliﬁer

settings, and that the cable is properly connected.

Clean the disc (page 55).

Interconnectors are not fully inserted into the terminals (or

are not connected).

Check that all interconnectors are ﬁrmly inserted.

Dirty or oxidized plugs/terminals.

•

Clean the plugs/terminals.

Incorrect audio cable connection.

Check the audio connections (pages 10 to 12).

Player's output is connected to the ampliﬁer's phono

(turntable) inputs.

Connect to any set of inputs except phono.

•

The disc is paused.

Press (PLAY) to exit the pause mode.

•

Incorrect ampliﬁer settings.

Check that the volume is turned up, that the speakers

are on, the input function set correctly, etc.

The analog audio is OK, but there appears to be no

digital audio signal.

•

Incorrect AUDIO SETUP menu settings.

Make sure that the DIGITAL OUT setting is set to ALL

or PCM (page 41).

Check the amp's instruction manual.

Additional Information

A disc containing the MP3 tracks won’t play.

•

If the disc is a recordable CD, make sure that the disc had

been ﬁnalized.

Check that the track(s) are in the MPEG1 Audio Layer

3 format.

Some MP3 tracks appear to be missing from a disc.

•

If a track name does not end in “.mp3” or “.MP3”, this

player will not recognize it as an MP3 track.

•

This player only recognizes about 650 ﬁles per folder and

300 folders per disc. If there are more titles than this, you

will not be able to play them.

•

This player is not compatible with multi-session discs.

If the disc is multi-session, you will only be able to play

tracks recorded onto the ﬁrst session.

The unit is connected to an HDMI/DVI component but

the HDMI/DVI indicator on the display does not light.

•

Set the input selector on the connected TV or HDMI/DVI

component to this unit.

This unit cannot be connected to TVs or HDMI/DVI

components that do not support HDCP.

Reset this unit and the TV or HDMI/DVI component by

turning them off and on.

No video appears on the connected HDMI/DVI

component.

•

Can the connected TV or HDMI/DVI component use the

selected resolution?

Set the HDMI VIDEO under HDMI Setup. (page 47)

•

Set the input selector on the connected TV or HDMI/DVI

component to this unit.

•

TVs or HDMI/DVI components that do not support HDCP

cannot output video from this unit.

No audio is coming from the connected HDMI

component.

•

The unit will not output an audio signal if Audio has been

turned off under HDMI AUDIO OUT Setup. (page 41)

Some HDMI-compatible monitors do not support audio

output.

The unit will not output an audio signal if a DVI

component has been connected.

Unable to play DivX movies.

•

Check that the DivX ﬁles are encoded with “Home

Theater's mode with DivX” certiﬁed encoder.

No sound during DivX movies playback.

•

The audio codes may not be supported by the DVD player.

A DivX movie does not repeat.

•

Check that ﬁle size of the movies does not exceed the ﬁle

size of the CD disc during burning.

Additional Information

21-pin connector assignment

Speciﬁcations

(Europe model only)

AV connector output ........................ 21-pin connector

This connector provides the video and audio signals

for connection to a compatible color TV or monitor.

General

System

DVD-Video, DVD-Audio, DVD R/RW, Super Audio

CD, Video CD, CD, MP3 ﬁles, JPEG ﬁles, DivX and

WMA

20 18 16 14 12 10 8 6 4 2

Power requirements (U.S.A.).................... 120 V, 60Hz

Power requirements (Europe)...........230 V, 50/60Hz

Power consumption................................................. 27 W

Power consumption in standby mode................0.8 W

Weight..............................................7.3 kg (16 lb 15 oz)

Dimensions ...........440 (W) x 128 (H) x 332 (D) mm

(17.3 (W) x 5 (H) x 13.1 (D) in.)

21 19 17 15 13 11 9 7 5 3 1

PIN no.

Audio 2/R out

Audio 1/L out

GND

15 R out

16 Blank

17 GND

Operating temperature

............................ +5 °C to +35 °C (+41 °F to +96 °F)

Operating humidity

B out

19 Video out

21 GND

Status

11 G out

....................................5 % to 85 % (no condensation)

S-Video output

Audio output

Y (luminance) - Output level...............1 Vp-p (75

)

Ω

Output level

C (color) - Output level................286 mVp-p (75

)

During audio output...................2 Vrms (1kHz, 0 dB)

Jacks..............................................................S-VIDEO jack

Number of channels ..................................................2/6

Jacks .................................................................... RCA jack

Video output

Audio characteristics

Output level ............................................1 Vp-p (75

)

Ω

Frequency response

Jacks .................................................................... RCA jack

...............................4 Hz to 44 kHz (DVD fs: 96 kHz)

S/N ratio .............................................................. 120 dB

Dynamic range .....................................................110 dB

Total harmonic distortion........................... 0.0008 %

Wow and ﬂutter: Limit of measurement ( 0.001 % W.

PEAK) or lower

Component video output (Y, C , C )

Output level.....................................Y: 1.0 Vp-p (75

)

C /P , C /P : 0.7 Vp-p (75

)

Jacks .................................................................. RCA jacks

HDMI output

Digital output

Output terminal .................................................... 19-pin

Coaxial digital output......................................RCA jack

Optical digital output................... Optical digital jack

Other terminals

Control in/out...................................................RCA jack

Flasher input...................................... Mini jack (3.5 )

RS232C ...........................................................................1

Accessories

Remote control ..............................................................1

AAA/R03 dry cell batteries.........................................2

Audio/Video cable (yellow/red/white) ....................1

System control cable....................................................1

Power cable.....................................................................1

User Guide (this manual)

Warranty card (USA only)

Note: The speciﬁcations and design of this product are

subject to change without notice, due to improvement.

(mm)

440

Additional Information

Printed in China

2007/01 PMC

00M30AK851310

Motorola MOTO W259 User Manual
Kenwood kdcx KDC X891 User Manual
Kenwood KDC D300 User Manual
Hitachi Travelstar HTS725032A7E635 User Manual
Hamilton Beach 44559 User Manual
Cuisinart DGB 600BCC User Manual
Centon electronic DataStick Pro DSP32GB 004 User Manual
Centon electronic DataStick Designer DSD4GB 006 User Manual
Blackberry Pearl 8100 User Manual
APC Smart UPS 100 Vac User Manual