®
COMPACT DISC PLAYER
AM/FM STEREO CASSETTE RECORDER
MODEL CD-210
OPERATING INSTRUCTIONS
PLAYS ALL MUSIC COMPACT DISCS
DIGITAL TUNING WITH 20 RADIO PRESETS
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT
RECEIVES AM/FM STEREO BROADCASTS
BASS BOOST SYSTEM
RECORDS FROM CD, RADIO, OR BUILT-IN MICROPHONE
2 WAY POWER - AC/DC
REQUIRES 8 SIZE “C” BATTERIES
•
•
•
•
•
•
•
•
PLEASE READ CAREFULLY BEFORE USE
CD-210SN021800 v.1 E
SAFETY INSTRUCTIONS
14.Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15.Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16.Servicing - The user should not attempt to service the appliance beyond that described
in the operating instructions. All other servicing should be referred to qualified service
personnel.
17.Power lines - An outdoor antenna should be located away from power lines.
18.Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be
sure the antenna system is grounded so as to provide some protection against voltage
surges and built up static charges. Section 810 of the National Electrical Code, ANSI/
NFPA 70 provides information with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA DISCHARGE UNIT (NEC
SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the
copyright laws of the United States and that prior permission be obtained from
copyright owners whenever copying tapes or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated on
the bottom of the set.
2
BATTERY SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery eletrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you can’t resolve the problem, or if the product is damaged,
refer to the LENOXX WARRANTY INFORMATION. Opening or removing covers
may expose you to dangerous voltages or other risks. Incorrect reassembly can
cause electric shock when the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch
your skin, and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
3
CHOOSING THE POWER SOURCES
You can use the AC power or batteries as a power source.
1. To a wall outlet
AC SOCKET
2. Battery compartment
TIP
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord to the
socket located at the rear of the player, and the
other end to the wall outlet.
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again. The
plugs are polarized and only
fits one way into the wall
outlet and back of the set.
2. Using the player on batteries
Insert 8 size “C” batteries (not supplied) into the
battery compartment.
TIP
Replace the batteries when
the POWER lamp dims or
when the player stops
operating. Replace all the
batteries with new ones.
Before you replace the
batteries, be sure to take out
the CD from the player and
remember to check the
Battery Safety Instructions
on Page 3.
To use the player on batteries, disconnect the AC
power cord from the player.
c
c
c
c
LOW ER
UPPER
c
c
c
c
4
LISTENING TO THE RADIO
3
1
2
Connect the supplied AC power cord or batteries (see page 4).
Press the POWER switch, the
POWER indicator will turn on.
1
Press the RADIO switch, the
RADIO indicator will turn on.
Press the AM/FM BAND switch to
select the desired wave band.
BAND
2
3
Tune into the station you prefer
using the TUNING UP or DOWN
button. Each time the button is
pressed, the frequency changes.
Keep the button pressed, the
station will change rapidly
(automatic tuning), release the
button and it will stop at the next
strong station.
(NOTE: For FM stations, stretch
the FM antenna out.)
If you tune into a FM stereo station,
“FM STEREO” will show in the
display.
4
5
To hear more BASS sounds, press
the BASS BOOST button.
5
PRESETTING STATIONS
5
4&6
Connect the supplied AC power cord or batteries (see page 4).
Follow Steps 1 to 3 (LISTENING
TO THE RADIO on the previous
page) to select a station.
1-3
4
PRESET
PROGRAM
Press the STORE button, “PRESET
”
PGM
will show and “ ” will flash
PROGRAM
in the display for about 6 seconds.
While the “
press the PRESET button to
choose a memory location (01-10).
” is flashing,
PROGRAM
PRESET
PROGRAM
5
6
Press the STORE button again to
PRESET
PGM
confirm,
broadcasting is stored into that
preset memory location. “
the
station
now
”
PROGRAM
disappears from the display.
NOTE: Steps 4-6 should be done quickly.
Repeat the above steps to store
other 9 stations into memory.
7
TIP: UP TO 10 AM AND 10 FM STATIONS CAN BE STORED INTO THE PRESET
MEMORY LOCATIONS. (THEY WILL REMAIN IN MEMORY AS LONG AS
THE BATTERIES ARE INSTALLED, OR AC POWER CORD IS CONNECTED.)
6
LISTENING TO THE PRESET STATIONS
(after you programmed them)
Connect the supplied AC power
cord or batteries (see page 4).
Make sure both POWER and
RADIO indicator lamps are on.
1
1
Press the AM/FM BAND
switch to select the desired
wave band.
BAND
2
3
Press the PRESET button
several times to choose a
memory location (01-10). You
will receive the station you
stored into that preset
memory location.
3
2
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
To
Press or Adjust
2
1
Adjust the volume
Turn off the Radio
VOLUME control
Press the POWER
switch.
TO IMPROVE RADIO RECEPTION
Change position of the antenna for FM or FM Stereo. Move the set itself for AM.
7
PLAYING A CD
3
2
1
4
Connect the supplied AC power cord or batteries (see page 4).
Press the POWER switch, the
POWER indicator lamp will go on.
1
2
Press the CD switch, the CD
TRACK
indicator lamp will go on and the
display will show 6 zeros.
Open the CD DOOR by pushing
it down at the position marked
OPEN/CLOSE and place the CD
3
OPEN
in the CD compartment.
CLOSE
The label side of the CD should
face upward.
Close the CD DOOR by pushing it
TRACK
OPEN
down at the position marked
OPEN/CLOSE again. The display
will show 6 zeros and then the total
4
CLOSE
number of tracks (songs) and the
TRACK
total playing time of the disc.
Press the CD PLAY button. The
player will play all the songs
(tracks) once.
TRACK
5
6
To hear more BASS sounds, press
the BASS BOOST button.
TIP: “
” WILL FLASH IN THE DISPLAY IF THERE IS NO DISC IN THE CD
COMPARTMENT OR THE DISC IS UPSIDE DOWN.
8
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME
CONTROL
TRACK
TIP
When CD play is
paused, the elapsed
playing time will flash
and no music will
play.
To
Press or Adjust
Adjust the volume
Stop playback
VOLUME control
To resume play,
press the PAUSE
button again, the
elapsed play time
will stop flashing and
music will play.
Pause playback
The elapsed playing time
will flash during pause.
Press again to resume play
after pause.
Go to the next track
TIP
Go back to the previous
track
If you bump the set
during CD play, the
music will stop or
or
while playing,
Locate a point in a song
skip for
a
few
press and hold down until
you find the point.
seconds. This is
normal for this type
of player.
Open the CD DOOR by
pushing it down at the
position marked “OPEN/
CLOSE” (press STOP
first).
Remove the CD
Press the POWER switch,
the POWER indicator
lamp will be off.
Turn off the power
9
PLAYING CD SONGS OVER AND OVER
(Repeat Play)
You can play CD tracks repeatedly in normal or programmed play modes (see page
11).
CD SWITCH
POWER SWITCH
1.Press the POWER switch, the POWER indicator lamp will be ON.
2.Press the CD switch, the CD indicator lamp will be ON.
3.Press the CD REPEAT (
) button.
To repeat
Press
The display shows
REPEAT
TRACK
a single track (song)
Press the REPEAT
button twice,
(
)
“REPEAT” will flash.
Press the REPEAT
REPEAT
TRACK
all the tracks (all songs)
programmed tracks
(
)
button once,
“REPEAT” will be steady
on.
Press the PROGRAM
(PGM) button, and then
the REPEAT button once
REPEAT
PROGRAM
TRACK
4.Select the track by pressing
or
, and then press
.
To Cancel Repeat Play
Press the REPEAT button until the “ REPEAT ” icon disappears in the display.
10
SELECTING YOUR OWN MUSIC PLAYING ORDER
(Programmed Play)
You can make a program of up to 20
tracks to play songs in the order you want
them to be played.
PROGRAM (PGM)
DISPLAY
During STOP mode, press the
PROGRAM ( PGM ) button. The
PROGRAM
1
2
PGM
TRACK
display will show
“
”,
“
” and “
” will flash
PROGRAM
TRACK
in the display.
PROGRAM
Press the SEARCH buttons
either or until the desired
track shows in the display.
TRACK
PROGRAM
Press the PROGRAM button. The
TRACK
PGM
3
4
display will show “
”.
Repeat steps 2&3 until all the
desired tracks are programmed.
( NOTE: Steps 1-4 should be done
quickly.)
Press the PLAY button to start
PROGRAM
TRACK
5
program play. “
”and the
PROGRAM
track number being played will
show in the display.
To check the order of tracks before play
Press the PROGRAM button during STOP mode.
Every time you press the button, the track number appears in the programmed order.
To change the current program
Just create a new program following the programing procedure.
To cancel Program Play
Press the STOP button.
11
PLAYING A CASSETTE TAPE
2
1
4
3
Connect the supplied AC power cord or batteries (see page 4).
Press the POWER switch, the
POWER indicator lamp will go on.
1
TAPE PLAY DIRECTION
Press the TAPE switch, the TAPE
indicator lamp will go on.
2
3
Press the STOP/EJECT button
to open the cassette door and
insert a recorded tape. Close
the door.
EMPTY
REEL
FULL
REEL
STOP/EJ.
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
Press the PLAY button.
The player turns on and starts
playing.
4
5
6
PLAY
When the player finishes playing
that side of the tape, the set will
stop. To hear the other side, flip
the tape over, then insert and
press PLAY.
AUTO STOP
To hear more BASS sounds, press
the BASS BOOST button.
12
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
BASS BOOST
FAST F.&
REWIND
PHONES
JACK
PAUSE
STOP/EJ
VOLUME
CONTROL
PLAY
To
Press or Adjust
Adjust the volume
Get different sound effect
Stop playback
VOLUME control
BASS BOOST switch for more BASS sounds
STOP/EJECT button
Fast forward or rewind the tape
Pause playback
FAST FORWARD button or REWIND button
PAUSE button
Press again to resume play after pause.
Eject the cassette
STOP/EJECT button (once or twice)
To enjoy the music without
disturbing others
Insert your headphone plug into the
PHONES JACK on the top of the set.
NOTE: Headphone is not
included.
13
RECORDING ON A TAPE
1
3
Connect the supplied AC power cord or batteries (see page 4).
Press the STOP/EJECT button to
open the tape compartment and
insert a blank tape. Select the
program source (AM, FM, CD, or
built-in microphone) you want to
record.
INSERT TAPE THIS WAY
FULL REEL ON RIGHT
1
2
To record from the CD player,
insert a CD and follow the steps to
play a CD (see page 8).
To record from a radio, press the
RADIO switch, and tune into the
station you want (see page 5).
To record from the built-in
microphone, press the TAPE
switch and speak in front of the
set.
Press the RECORD button to
start recording. (The PLAY button
is depressed automatically.)
3
4
To hear what you recorded, press
TAPE switch, then REWIND and
PLAY.
14
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
TIP
• Adjusting the VOLUME
or pressing the BASS
BOOST will not affect
the recording level.
POWER
SWITCH
PAUSE STOP/EJECT
• For best recording
effect, use the AC
To
Press or Adjust
power
instead
of
batteries.
Stop recording
STOP/EJECT button
• To erase a recording,
just start new
recording, and the old
one is automatically
replaced.
Pause recording
PAUSE button
Press the button again to
resume recording.
a
Turn off the power
Press the STOP/EJECT
button and the POWER
switch.
15
PRECAUTIONS
On Safety
On Power Sources
As the laser beam used in the CD
For battery operation, use 8 size C
•
•
player section is harmful to the eyes,
do not attempt to disassemble the
cabinet. Refer servicing to qualified
personnel only.
batteries. We recommend alkaline
batteries for longer life.
When the batteries are not to be used,
•
remove them to avoid damage that can
be caused by battery leakage or
corrosion.
Should any solid object or liquid fall into
•
the player, unplug the player, and have
it checked by qualified personnel before
operating it any further.
On Operation
If the player is brought directly from a
•
On Placement
cold to a warm location, or is placed in
a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
player will not operate properly. In this
case, remove the CD and wait about an
hour for the moisture to evaporate.
Do not leave the player in a location
•
near heat source, or in a place subject
to direct sunlight, excessive dust or
mechanical shock.
Do not place the player on an inclined
or unstable place.
•
If the player has not been used for a
long time, set it in the playback mode
to warm it up for a few minutes before
inserting a cassette.
Do not place anything within 1 inch of
•
the back of the cabinet. The ventilation
holes must not be covered for the
player to operate properly and prolong
the life of its components.
This CD player is designed to be played
•
on a stable no vibration position. If you
bump the set during CD play, the music
will stop or skip for a few seconds. This
is normal for this type of player.
If the player is left in a car parked in
•
the sun, be sure to choose a location
in the car where the player will not be
subjected to the direct rays of the sun.
If you have any questions or problems
•
Since a strong magnet is used for the
•
concerning your player, please contact
our customer service department at
1-800-315-5885.
(MONDAY - THURSDAY 09:00 AM - 05:00 PM,
FRIDAY 09:00 AM - 01:00 PM EST)
speakers, keep personal credit cards
using magnetic coding or spring-wound
watches away from the player to prevent
possible damage from the magnets.
16
PRECAUTIONS (continued)
Notes on Cassettes
Notes on CDs
Before playing, clean the CD with a
Break off the cassette tab from side A
•
•
cleaning cloth. Wipe the CD from the
center out.
or B to prevent accidental recording.
If you want to reuse the tape for
recording, cover the broken tab with
adhesive tape.
Side A
Tab for side A
Tab for side B
Do not use solvents such as benzene,
•
•
thinner,
commercially
available
cleaners or anti-static spray intended
for vinyl LPs.
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
Do not expose the CD to direct
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car.
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
To reduce the chances of tape jamming
Do not stick paper or stickers on the
CD, nor scratch the CD.
•
•
•
or tangling, you should check that
there are no loose layers of tape visible
through the cassette center window. If
any, tighten these loose layers of tape
using a pencil before inserting the
cassette into the set.
After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
17
MAINTENANCE
Notes for Storing Cassette
Tapes
Cleaning the Lens
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner and blower.
1. Do not put a tape near a magnetic field,
such as a TV, or speaker. Magnetic
fields may reduce the tape sensitivity
or even erase the recording.
2. Do not store tape for any length of time
in a hot, moist or dusty place.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and the
capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, insert a tape when the areas
Cleaning the Cabinet
Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type
of abrasive pad, scouring powder, or
solvent, such as alcohol or benzene.
RECORD/PLAY BACK HEAD
PINCH ROLLER
ERASE HEAD
CAPSTAN
COTTON SWAB
cleaned are completely dry.
NOTE: In order to see and clean the
head, you may have to press
PLAY first.
18
TROUBLESHOOTING
Remedy
Problem
Connect the AC power cord to a wall
outlet securely.
Make sure the batteries are inserted
correctly and they are fresh.
•
•
The power is not on or the
POWER indicator lamp is dim.
Make sure the appropriate indicator
lamp is ON as you want.
•
There is no sound.
Adjust the volume.
Unplug the headphones when listening
through speakers.
•
•
“
” flashes in the display
Insert the CD with the label side up.
•
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
Take out the CD and leave the CD door
open for about an hour to dry moisture
condensation.
•
•
CD does not play.
•
Make sure the CD indicator lamp is ON.
Clean the CD, or replace it if the CD is
badly damaged.
•
•
The sound drops out.
Place the player in a location free from
vibration.
•
Check if your batteries are fresh.
Check if the CD itself is damaged by playing
it in another set.
•
•
The sound is weak or has poor
quality.
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
•
Make sure the safety tab on the cassette
is in place.
Make sure the TAPE indicator lamp is ON.
Make sure the tape is not at the end. Press
•
The RECORD button does not
function/The tape does not play.
•
•
REWIND then RECORD.
Clean the erasing head (see page 18).
Replace all the batteries with new ones if
they are weak.
The tape does not erase
completely.
•
•
Make sure the tape is inserted properly.
Make sure the safety tab of the cassette
is in place.
•
The tape does not record.
•
Clean the heads, pinch roller and capstan
(see page 18).
The sound is weak/The sound
quality is poor.
•
The tape has reached its end. Remove it,
flip to the other side and re-insert. Or
press REWIND and PLAY to hear that side.
•
Cassette PLAY button pops up.
19
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 15Watts
DC 12V (8 size “C” batteries)
(Alkaline batteries are recommended)
Speakers:
2-4” 8 ohm
2.2W / channel
1
Output power:
Dimensions:
Width: 16 / ”
4
Depth: 10”
Height: 7”
Weight: 7LBs (without batteries)
CD Section
Plays disc type:
Any normal CD used in portable players
760 - 800 NM
Laser wavelength:
Tracking method:
Frequency response:
3 - spot error detection
80Hz - 15 KHz
3.86 mm lens
Tape Recorder Section
Frequency response: Standard normal bias cassette tape,
70 - 10 KHz
Radio Section
Frequency range:
FM: 87.5 - 108 MHz
AM: 520 - 1710 KHz
LENOXX reserves the right to make design and specification changes for product
improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND A CLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED
UNDER THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER
FINISH.
For Customer Service Dial 1-800-315-5885
(MONDAY - THURSDAY 09:00 AM - 5:00 PM, FRIDAY 09:00 AM - 1:00 PM EST)
© 2000 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
CD-210SN021800 v.1 E
20
|