P3 / P3 EVOLUTION
®
TECHNICAL CHARACTERISTICS
LEGEND
F
WATER FILTER
VA ONE-WAY VALVE
D
ANTI-LIMESTONE FILTER (optional)
CV FLOWMETER
Dimensions: Height 62 cm
P
PUMP
Width 42 cm
Depth 40 cm
V
C
ONE-WAY VALVE
BOILER
Ev1 TEA OR SOLUBLE COFFEE VALVE
Ev2 MILK & CHOCOLATE VALVE
Ev3 HOT WATER VALVE (OPTIONAL)
EvE ESPRESSO COFFEE VALVE
Weight:
35 Kg
Voltage supply: 230 Vac. 50 Hz or 120 Vac. 60Hz on request
Absorbed power: 1,6 KW
GE ESPRESSO GROUP
S
WASTE
Selections: 11 selections.
M1 TEA OR COFFEE MIXER
M2 MILK & CHOCOLATE MIXER
System of payment: predisposed for
U1 TEA SPOUT
ꢀ
ꢀ
ꢀ
Obliterator / token system 24Vdc
Selector 12Vac or 24Vac
Executive / MDB system
U2 MILK&CHOCOLATE SPOUT
U3 HOT WATER SPOUT (OPTIONAL)
UC ESPRESSO SPOUT
Water connection: inside tank 15lit.
Optional:
ꢁ
ꢁ
ꢁ
connection kit to the mains water
Small cabinet with puck & waste containers
beniamino filter (anti-limestone filter)
ꢁ
Cables for Executive / MDB connection
Pag. 2
Pag. 27
WATER FLOW DIAGRAM
GRINDER
The quantity of ground coffee is adjustable through a screw (2); screwing it the
quantity decreases, while unscrewing it, the quantity increases..
To adjust the degree of grinding, after having pushed the lock (6), act on the
grind-stone holder (1), clockwise to have a finer grinding, while in counterclock-
wise to obtain a bigger grinding.
Make sure that the lock comes back in the hole of block of the grind-stone holder,
before starting the grinder.
Pag. 26
Pag. 3
LEGEND
INSTALLATION
A
Main power
B
C
D
E
F
G
Main switch
Before installing the machine, read carefully this manual.
Install the machine in a dry and hygienic place.
“Anti-interference” filter
Transformer 230/24 Vac or 120/24 Vac
Coffee group heating elem. 24 Vac
Ventilator
ELECTRIC CONNECTION
Safety clixon 145°C
H
IP
S
MG
MS
MD
GA
MC
CV
Boiler heating element 1200 W
“Door” safety switch
Boiler temperature sensor
“Supply” group-microswitch
“Pause” group-microswitch
“Coffee-doser” microswitch
Float
Before connecting the machine to an electric plug, please follow these precau-
tions:
•
•
The main supply must correspond to the power requirements of the machine
(1600W).
Check that the power supply voltage correspond to the voltage shown in the
rating label.
“Token system” contact.
Flowmeter
1
2
3
4
5
7
8
9
GRINDER MOTOR
•
•
Check that the main socket is correctly earthed.
If the power supply cable is replaced, use only original type cables (request the
special cable with M type connection to the manufacturer).
COFFEE-RELEASER SOLENOID
COFFEE-GROUP MOTOR
COFFEE ELECTRO-VALVE
PUMP
“MILK & CHOCOLATE” ELECTRO-VALVE & MIXER
MILK DOSER-MOTOR
The manufacturer will not accept responsibility for any
damage arising if these precautions are not complied
with.
“TOKEN SYSTEM” COIL
10 CHOCOLATE DOSER-MOTOR
11 TEA ELECTRO-VALVE & MIXER
12 TEA DOSER-MOTOR
The machine is provided of a general lighted switch, located on the back panel
and of a security push button placed on the chassis that breaks off the power to
the electronic board when you open the door. To restore the power also with the
door opened, take out the push button.
13 HOT WATER ELECTRO-VALVE
F1
F2
1.6A FUSE
10A FUSE
All the electric devices in the machine work with a 24 Vdc voltage, except the
boiler heating element and the transformer that work with 230 or 115 Vac.
WIRE COLORS
00 black
11 Brown
22 Red
33 Orange
44 Yellow
55 Green
66
Blue
Violet
Grey
77
88
99
White
XX Pink
YY Light blue
Pag. 4
Pag. 25
HYDRAULIC CONNECTION
ELECTRICAL DIAGRAM
The machine could be installed on:
•
•
a cabinet with place for cups, spoons and sugar and a water tank of 15lt
a small base with waste containers (the machine has to be with mains water
connection).
On cabinet
ꢀ
ꢀ
Place the dispenser on the base and fix it with the screws.
Fill up the special water tank with potable water, insert the tube with the
filter and the one-way valve , and if it's present, the float.
Insert in the tank of 5 lt. the waste pipe.
Fix a bag to the apposite hook for the coffee grounds.
Fill the containers, with the apposite products.
ꢀ
ꢀ
ꢀ
On small base
ꢀ
Check the mains pressure doesn’t exceed 2 bar, otherwise it is necessary to
install a pressure-reductor.
ꢀ
ꢀ
Connect the mains pipe to the electro valve.
Verify, through the manometer inside the machine, that the pressure doesn’t
overcome 1 bar, otherwise adjust it with the inside reductor.
Fill the containers, with the apposite products.
ꢀ
PAYMENT SYSTEM CONNECTION
•
•
VALIDATOR 12V connect to the keyboard connector COIN12V (see
figure at page 6).
VALIDATOR 24V connect to the keyboard connector COIN12V (see
figure at page 6).
•
•
EXECUTIVE / MDB connect to the relative cables (optional)
SINGLE IMPLUSE SYSTEM (obliterator, token system, etc.) connect to the
connector 6 pins in the right up angle of the machine.
After the electric connection, it is necessary to set the used system into the pro-
gram (see page 13).
Pag. 24
Pag. 5
SWITCHING ON
TROUBLESHOOTING GUIDE
The machine is provided with a program of self-diagnosis, that allows to visualize
on the display the messages of breakdown or machine stopped :
After having followed all the instructions of installation, it is possible to turn on
the machine through the light switch situated on the frontal side of the electric
panel.
ERROR GROUP 1
ERROR GROUP 0
ERR. COFFEE FLOW
ERR. SOLUB.FLOW
ERROR GRINDER 1
the coffee-group has not reached the “supply position” given by its right
micro switch. Check Fuses, group right micro switch, group motor,
electronic board..
At the switch on of the machine, it appears on display for a brief time the message
of the version software, after that it will begin the heating of the boiler that will be
visualized with the message" HEATING" that will be replaced, to reached tem-
perature, from the flowing message". ….INSERT THE CREDIT AND SELECT
YOUR DRINK…”.
the coffee-group has not reached the “normal position” given by its left
micro switch. Check Fuses, group left micro switch, group motor, elec-
tronic board.
During espresso supplying, the board has not received signals from the
flowmeter. Check fuses, too fine coffee, coffee pump, coffee electro
valve, flowmeter, electronic board.
Note: it is advisable immediately to execute a manual washing after the
switch on, to load with more facility the hydraulic circuit and the boiler.
To do this, make reference to the" quick functions" at page 22.
During soluble supplying, the board has not received signals from the
flowmeter. Check fuses, soluble pump, soluble electro valve, flow-
meter, electronic board.
During the coffee grinding, the board has not received the signal given
by the doser-switch in the maximum time of 25 seconds. Check too
fine coffee, fuses, doser micro-switch, grinder motor, grinder blocked
by something hard, electronic board.
Keyboard description
LACK OF WATER
ERROR BOILER 1
The board doesn’t receive the signal from the float. Lack of water, float,
water container micro switch, electronic board.
The board has not received the programmed value temperature from the
boiler probe in the maximum time of 15 minutes. Check safety thermo-
stat, boiler heating element, electronic board.
EMPTY GROUNDS!
ERROR EXECUTIVE
The coffee grounds decounter has reached the programmed value.
Empty the grounds and execute the quick function nr.5.
The board does not receive signals by the payment system, Executive or
MDB, programmed. Check payment system, cables, electronic board..
ERROR MIXER
the board has received too much current from the whipper motor used.
Check the whipper or clean the mixer.
All the alarms are deleted, once the trouble is solved, switching off the machine.
Pag. 6
Pag. 23
QUICK FUNCTIONS
PROGRAMMING
In this section, it is possible to perform some of the most useful functions by the
loader.
There are 2 levels of program: a frequent menu and a main menu.
The frequent menu is useful to the operator to regulate the dosing of the drinks, to
set the prices, to notice the counters and to visualize the events of the machine.
To access press the button “QUICK MENU” of the keyboard (see page 6).
On display you will see “QUICK MENU ”
The main menu is useful to the technical sector of the management and it is for
setting the various parameters of the machine.
Pushing the relative number, you will execute these following functions::
The buttons used in the programming are the followings:
1. mixers washing: a washing for each mixing group is executed.
2. boiler 1 temperature visualization: you see for 2 seconds the pre-
sent temperature of the boiler 1.
1
2
3
4
5
6
7
8
9
0
E
3. total counter visualization: the display will show the total counter of the
machine for 3 seconds. It is not possible to reset this counter..
4. free mode working: setting the “free mode” working. After 1 minute
Answer NO to the question
Answer YES to the question
of inactivity the machine comes back in regular working.
5. grounds counter reset: the coffee grounds counter is reset to the
value programmed on the “level 2 menu”. The message “empty
grounds !” will disappear and the machine will continue to work.
(+) has the function of increase or advancement in the program
(-) has the function of diminution or withdrawal in the program
(ESC) has the function of exit
6. filter counter reset: the filter counter is reset to the value pro-
grammed in “level 2” menu. After that, the symbol “*” will disap-
pear.
(ENTER) has the function of confirmation.
7. espresso group motor test: you can test the espresso group move-
ment. Pushing the button 7, you will supply the motor, while keep-
ing pressed it, the motor will move to the next position, “supply po-
sition” or “normal position”.
FREQUENT MENU
The access to this menu happens through the pressure of the key PROG of the
keyboard.
On display the following menus will appear: :
8. coffee decounter reset: the coffee decounter is reset to the value
programmed (see also at page 21).
9. chocolate decounter reset: the chocolate decounter is reset to the value pro-
grammed (see also at page 21).
•
•
•
•
SET DRINKS
SET PRICES
COUNTERS & AMOUNTS
EVENTS
Pag. 22
Pag. 7
Movements nr 20 and 21 (Decounter coffee and
chocolate)
SET DRINKS
Entering the program through E, you will see the sequence of the existing drink
codes.
The movements nr20 (decounter coffee) and nr21 (decounter chocolate), where
inserted, decrease the relative decounter by a unit.
To set the value of the decounter, it is enough to change it in one selection which
contains it, automatically it will be modified also in all the other selections.
01-02-03-04-05-0
Sel.1
The flashing cursor points out the drink code selected, to move it use the keys + to
advance or - to withdraw; contemporarily to the movement of the cursor, in the
underlying line, the name of the selection will be visualized related to the drink
code.
If the parameter “type” is set=0, every time it is reset, see at page 22, the decoun-
ter restart to the set value, while if the parameter “type” is set=1, at every reset,
the decounter value will be the sum of the set value plus the value before the reset.
Example with value= 100 and type=0
If the decounter is reset when its value was 20, the new decounter value is 100.
To modify the parameters of the drink code press E.
A sequence of numbers will be visualized that correspond to the doses of the se-
lection, the line price (P) and the menu of the name of the drink (MS).
Example with value=100 and type=1
If the decounter is reset when its value was 20, the new decounter value is 120
(100+20).
07-P1-MS
ESPRESSO 1
In both of cases, when the decounter reaches 0, the display will show “Machine
ready coffee finished” or “Machine ready choco finished” or “Machine ready
No coffee&choco” and the machine will disable the selections which contains the
relative decounter (movements 20 and 21).
As in precedence, the cursor points out the dosing code selected, therefore to
move it use the keys + or -; on the underlying line the description of the selected
dosing will appear.
To modify its value, after having selected it, press E.
ESPRESSO WATER
45
Use the numerical keys from 0 to 9 to insert the desired value and to confirm
press E.
To exit of the menu press “9”.
SAVE CHANGES ?
YES=6
NO=5
Press" 6" to confirm the changes or" 5" to cancel it.
Pag. 8
Pag. 21
It is possible to eliminate, to modify or to insert movements or to change its regu-
lations where possible, for example the dosing of the products.
To modify the name of the drink use the keys:
" 7" to withdraw with the cursor on the character
" 6" to advance with the cursor on the character
"+" or" -" to modify the character
·
·
·
·
·
to move the selection cursor movement use + and -
to insert a new movement in the selected position press" 2"
to eliminate the selected movement press" 1"
to modify the selected movement press" 3"
Example: change the water quantity of the coffee of the selection " long coffee"
n°2
to modify the regulations (es: dosing) press E
enter in" set drinks" with E
position the cursor on the code drink n°2 with the key +
enter with E the sequence dosing
position the cursor on the dosing n°7 with +
press E to enter the change value
use the numerical keys to set the desired value and press E to confirm it
press 9 to go out of the menu "dosing drink"
press" 6" to confirm the changes
To modify the name of the drink use the keys:
" 7" to withdraw with the cursor on the character to modify
" 6" to advance with the cursor on the character to modify
"+" or" -" to modify the character
The movements are:
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
CUP
GRINDER 1
SOLUB. 1 VOLUM.
SOLUB. 2 VOLUM.
SOLUB. 3 VOLUM.
SUGAR
the cup-dispenser (IF PRESENT) releases a cup.
the grinder produces a coffee dose.
press 9 to go out of the menu "set drinks"
The machine makes the soluble 1 (milk) cycle with volumetric control (in cc).
The machine makes the soluble 2 (chocolate) cycle with volumetric control (in cc).
The machine makes the soluble 3 (tea) cycle with volumetric control (in cc).
the machine gives a dose of sugar in the cup
the coffee dose is released into the infusion chamber and the espresso supplying is executed.
The machine makes the soluble 4 (coffee lio) cycle with volumetric control (in cc).
The machine makes the soluble 5 cycle with volumetric control (in cc).
a pause is executed
ESPRESSO 1
SOLUB. 4 VOLUM.
SOLUB. 5 VOLUM.
PAUSE TYPE 1
PAUSE TYPE 2
PAUSE TYPE 3
PAUSE TYPE 4
LIOF. SOLUBLE 4
SOL.4 LIOF.SUG.V.
SET PRICES
a pause is executed
a pause is executed
a pause is executed
In this menu it is possible to set the value of 9 prices lines , to which the various
selections are linked.
The machine gives the soluble 4 ( coffee) powder (used for light kinds of powder).
The machine gives a dose of sugar into the soluble 4 mixing group and a quantity of water with
volumetric control.
16
SOL.4 LIOF.SUG.T.
The machine gives a dose of sugar into the soluble 4 mixing group and a quantity of water with
time control.
To select the price line to set, use the keys + or -, enter the change of the value
pressing E and set the value with the numerical keys, after that press E to confirm.
17
18
LIOF. SOLUBLE 5
SOL.5 LIOF.SUG.V
The machine gives the soluble 5 powder (used for light kinds of powder).
The machine gives a dose of sugar into the soluble 5 mixing group and a quantity of water with
volumetric control.
19
SOL.5 LIOF.SUG.T
The machine gives a dose of sugar into the soluble 5 mixing group and a quantity of water with
time control.
If all the price lines have the value 0, the machine will work in “test mode”, show-
ing it on the display.
20
21
22
23
24
25
26
27
28
29
COFFEE DECOUNTER
CHOCO DECOUNTER
SOLUBLE 1 TIME
SOLUBLE 2 TIME
SOLUBLE 3 TIME
SOLUBLE 4 TIME
SOLUBLE 5 TIME
GRINDER 1
the coffee decounter decreases by one unit.
the chocolate decounter decreases by one unit.
The machine makes the soluble 1 (milk) cycle with time control.
The machine makes the soluble 2 (chocolate) cycle with time control.
The machine makes the soluble 3 (tea) cycle with time control.
The machine makes the soluble 4 (coffee lio) cycle with time control.
The machine makes the soluble 5 cycle with time control.
the grinder produces a coffee dose with time control.
a hot water quantity is supplied with volumetric control.
a hot water quantity is supplied with time control.
HOT WATER
ON TIME WATER
Important: some movements could not work, depending on the model of the machine.
Consult the manufacturer in case you want to modify the sequence of movements.
Pag. 20
Pag. 9
COUNTERS & AMOUNTS
SET DRINKS
In this menu it is possible to notice the counters of the various selections and
eventually to reset them.
Premise: every selection or drink it is composed from a sequence of movements
which correspond to a single operation of the machine.
The single movements are only performed after the correct event of the previous
movement, in case of not-correct operation the machine will go to alarm.
Press E to enter the menu that is composed in the following parameters:
TOTAL COUNTERS&AMOUNTS
THE CORRECT SEQUENCE OF COMPOSITION OF THE SELECTIONS
IS ALREADY SET FROM THE MANUFACTURER, THEREFORE HE
RECOMMENDS YOU TO NOT MODIFY THE CORRECT SEQUENCE
WITHOUT CONSULTING THE MANUFACTURER.
total in normal working of counters and amounts (Pcs.) from the last zero
resetting.
TEST MODE: TOTAL COUNTERS&AMOUNTS
total in test working of counters and amounts (Pcs.).
Entering the program through E you will see the sequence of the existing drink
codes.
FREE MODE: COUNTERS&AMOUNTS
total in "free test" working of the done tests and of theirs "loss" in relation-
ship to the price of the effected selections.
01-02-03-04-05-0
Sel. 1
RESET COUNTERS?
Zero resetting of all the counters. Press "6" to reset or "5" to cancel.
The flashing cursor points out the code drink, to move it use the keys + to advance
or - to withdraw; contemporarily to the cursor movement, in the underlying line
the name of the selection will be visualized related to the code drink.
To modify the parameters of the code drink, press E.
A sequence of numbers will be visualized each of which corresponds to a move-
ment of the machine.
02-07-P1-MS
Sel. 1
As for the drinks, the cursor points out the code movement, therefore to move it
use the keys + or -; on the underlying line the description of the movement will
appear.
Every drink is composed therefore from a sequence of" movements", from a
line price and from the menu of its name" MS."
Pag. 10
Pag. 19
Electrical OUTPUT
EVENTS
In this menu it is possible to notice the last 100 events of the machine.
Entering the menu with ENTER the following data will be visualized:
N° description
1
Date : hour & date
Not used
ID:XXX RESULT POS
2
Grinder motor
3
Coffee releaser solenoid
The time and the date of the event are not available.
ID indicates the kind of event, that can be a code drink or an internal operation of
the machine (see chart).
RESULT indicates if the event has gone to good end (GOOD) or an error is oc-
curred (Ennn) where nnn corresponds to a number that the type of error represents
(see chart).
4
Espresso unit motor
5
ETV espresso
6
Pump
7
ETV / whipper sol. 1/2 (milk / chocolate)
POS indicates the position of the event (from 1 to 100).
To scroll the various events use the keys + and -.
8
Powder motor sol.1 (milk)
Internal operation codes
9
Not used
10
94 espresso group positioning
96 filter counter reached
97 boiler 1 refilling
99 washing
Powder motor sol. 2 (chocolate)
11
ETV / whipper sol. 3 (tea)
12
Powder motor sol. 3 (tea)
13
Not used
Errors codes
To choose the output, push + or -, to supply it, press Enter.
To exit from this menu, press PROG.
E103
E104
E105
E106
E107
E112
E113
E115
E118
E119
E120
E121
E123
espresso group positioning in “normal position”
espresso group positioning in “supply position”
espresso supplying
soluble supplying
coffee grinding
lack of water
boiler 1 temperature
coffee pucks counter
boiler 1 off by timer
“executive or MDB” communication during working
“executive or MDB” communication at power on
whipper over-current
33Vdc fuse broken
Pag. 18
Pag. 11
RESET COUNTERS&AMOUNTS: Reset of all the counters above. Press “6”
to confirm or “5” to cancel.
MAIN MENU
To access this menu, keep pressed the button PROG for 5 seconds.
ENABLE SLAVE MACHINE Enable the “slave” machine (not available).
The menu is composed by the followings programs:
ENABLE TEMPERAT.ON DISPLAY: Visualization on display of the boiler
temperature.
PAYMENT SYSTEM
Setting of the system of payment and its options.
SERIAL NUMBER: set the serial number of the machine.
SET TEMPERATURE
CAUTION ! OUTPUT TEST !: test of all the electrical output of the electronic
board (see the chart at page 18).
Setting of temperatures and other functions on the boilers.
OPTIONS: INSERT PASSWORD
TYPE OF MACHINE: set-up of the model of the machine.
Entry to the options related to the levels of programming: operator and
technician or manager.
ENABLE AUTOMATIC WASHING: if enabled, the machine executes an auto-
matic washing cycle at the power-on.
DISPLAY COUNTERS ENABLE: if enabled, at the power-on the display will
show the total counter, which can’t be reseted.
BOILER 1 WORKING: enable of the boiler 1.
Note 1: to avoid the blocks in the mixing group, the software controls the powder
and water values in the way explained in the following diagram.
Pag. 12
Pag. 17
OPTIONS: LEVEL 2 (manager- technician)
PAYMENT SYSTEM
After having inserted the correct password, that it initially is" ask to manufac-
turer", you will enter in the following menu:
The followings programs compose this menu:
SET COIN VALUE PARALLEL SYSTEM
MODIFY PASSWORD LEVEL 1: Insert the new password and press E to con-
Setting of the coin values (see note 1).
firm.
DECIMAL POINT
MODIFY PASSWORD LEVEL 2: Insert the new password and press E to con-
firm.
Setting of the decimal point to be applied to coin and prices values.
NAME OF CURRENCY
SET DRINKS: See ”set drinks” chapter at page 19.
Setting of the currency.
LOAD DEFAULT DATA: Original data loading. To confirm press “6” while to
cancel press “5”.
SINGLE SALE NO CHANGE GIVEN
Setting of the sale without maintenance of the residual credit.
SET LANGUAGE: Language of all the message .
MAXIMUM CHANGE GIVEN
Maximum value of the credit to be given (for change giver systems
only).
SET DELAY POWDER: Set the delay between the water and the powder, in
tenth of seconds (see note 1).
TYPE OF PAYMENT SYSTEM
SET WATER QUEUE: Reserve of water without powder at the end of the selec-
tion, in tenth of seconds (see note 1).
Type of payment system used on the machine (see note 2).
SET PAUSE ESPRESSO GROUP: Time for coffee puck drying, in tenth of
seconds.
Note 1: this menu is only valid for parallel selectors.
To memorize the values coin proceed in the following way:
Set the value of the coin to accept with the numerical buttons
introduce the coin in the selector
ENABLE BITTER DRINK AS DEFAULT: Kind of sugar / no sugar drink (not
available)
SET FILTER COUNTER: Counter for the limestone filter substitution. Once
reached, the machine will show “*” on display but it will continue to work (see
also at page 22).
if accepted, on the display the channel will appear on which is pro-
grammed
press F4 to confirm the memorization.
Repeat the procedure for the other coins.
SET NUMBER OF COFFEE GROUNDS: Counter for coffee pucks emptying.
Once reached, the machine will show “EMPTY GROUNDS” and it will stop (see
also at page 22).
Note 2: after having programmed the type of system of payment, it is necessary to
go out of the program with ESC and switch off the machine.
REGULAR MODE COUNTERS&AMOUNTS: regular mode counter.
TEST MODE COUNTERS&AMOUNTS: test mode working counter.
FREE MODE COUNTERS&AMOUNTS: Free mode working counter.
Pag. 16
Pag. 13
SET TEMPERATURE
OPTIONS: LEVEL 1 (operator)
The followings programs compose this menu:
After having inserted the correct password, which initially is "ask to the manufac-
turer”, the following menu will compare:
SET BOILER 1 TEMPERATURE
Set-up of the boiler 1 temperature.
MODIFY PASSWORD LEVEL 1: Insert the new password and press E to con-
firm.
TIME OVERHEATING BOILER 1
After this time of “machine stopped” the boiler 1 is overheated.
TEST MACHINE MODE: Set the machine in Test mode working.
FREE MODE: Set the machine in Free mode working.
SET OVERHEATING BOILER 1
Value of overheating of the boiler 1 (max. 5°C).
SINGLE DRINK COUNTERS&AMOUNTS: Choose the id drink to analyze
with + or - and E to confirm.
TIME FILLING UP BOILER 1
Every “minute set” the pump refills the boiler 1 to keep the maximum
level.
REGULAR COUNTERS: Regular working counter.
TEST MODE COUNTERS&AMOUNTS: Test mode working counter.
FREE MODE COUNTERS&AMOUNTS: Free mode working counter.
SET FILLING UP BOILER 1
Duration of refilling for boiler 1.
RESET COUNTERS&AMOUNTS: Resetting all the counters above. Press “6”
to confirm or “5” to cancel.
OPTIONS
This menu is constituted by 2 different levels each of which it is protected from a
password:
1st level. Operator - devoted to the operator of the machine
2nd level. Manager - devoted to the technician / manager of the machine
The machine has 3 types of operation each of which it has a counter of selections
and amounts:
normal:
normal working with selection priced
test :
working with selections priced but with the money does-
n’t go into the coin box (example: the technician has to
test the machine and the payment system).
working with free selections.
Free test:
The counters of every level are independent one with the other, therefore the zero
resetting of the counters of a level doesn't influence the counters of the other level.
Pag. 14
Pag. 15
|