WS-8236U
ATOMIC CLOCK WITH TEMPERATURE, HUMIDITY AND
MOON PHASE
Instruction Manual
FEATURES:
ATOMIC CLOCK:
Hanging holes
LCD1
display
LCD2
display
Battery cover
Function keys
Foldable stands
•
•
•
•
•
•
•
•
•
•
•
WWVB Radio controlled time with manual time setting
Time display: hour, minute, second
Alarm setting with snooze function
Complete calendar display
Weekday display (3 languages to choose from: English, French and Spanish)
Time zone setting
Daylight savings time ON/OFF option (DST)
Indoor temperature display
Indoor humidity display
Wall mount or freestanding
Moon phase display
1
+ key
ALM key
:
:
To change any values in manual set mode or alarm set mode
To enter into the alarm set mode
To set the alarm ON/OFF
To display the alarm time in normal mode display
To exit the setting modes
SNZ key
:
To activate the snooze function during alarm
ATOMIC CLOCK LCD SCREEN DESCRIPTIONS
The atomic clock's LCD is divided into 2 sections and once the batteries are inserted, all the
segments will light up briefly before displaying the information for time, date, indoor temperature,
indoor humidity, and second.
Radio
reception icon
WWVB time
Alarm icon
Month
Moon Phase Display
Date
Weekday
Indoor humidity
and temperature
Second
Display
MANUAL SETTINGS
Note:
If the atomic clock has already successfully received the WWVB time signal and displays
the correct time and date, then the Manual settings can be skipped.
3
After completion of the above described procedures in “Setting up” the manual setting modes
can be entered by pressing and holding the SET key for 5 seconds. The following settings can
now be programmed:
Default (Factory) Setting
•
•
•
•
•
•
•
•
•
LCD contrast setting
Time zone setting
DST ON/OFF
Radio-controlled time ON/OFF
Language display setting
Manual time setting (Hour then Minute)
Year setting
4
-5 (Eastern Standard Time)
ON
ON
ENG (English)
12 (hour), 00 (minute)
2004
Jan (January)
1
Month setting
Date setting
LCD CONTRAST SETTING
After entering the manual setting mode as described above, the LCD contrast can be set between
0 and 7.
1.
2.
Press and hold the SET key for 5 seconds.
LCD will be displayed in the lower display and a number will flash to the right of the word
LCD.
3.
4.
Press and release the + key to select the desired LCD contrast.
Press and release the SET key to confirm the LCD contrast and continue to the Time Zone
setting.
TIME ZONE SETTING
The time zone can be set between the –1 to –12 hour or Greenwich Mean Time (GMT) range.
1.
The time zone will start flashing (Default setting "-5h“) in the lower LCD display.
4
2.
3.
Press and release the + key to select the desired time zone.
Press and release the SET key to confirm the time zone setting and continue to the DST
(Daylight Saving Time) setting.
Note: The time zones from –4 to –10 hours will be displayed with 3 characters abbreviations:
•
•
•
•
•
•
•
•
-4 ATL (Atlantic time),
-5 EST (Eastern time; default time zone),
-6 CST (Central time),
-7 MST (Mountain time),
-8 PST (Pacific time),
-9 ALA (Alaska time),
-10 HAW (Hawaii time).
"GMT” will be displayed if set to GMT (0).
DST SETTING (daylight saving time)
1.
The word ON will start flashing in the lower LCD display.
2.
3.
Press and release the + key to select DST ON or OFF.
Press and release the SET key to confirm the DST setting and continue to the Radio-
controlled time setting.
Note: The DST default is “ON”, meaning that the WWVB will automatically change the time
according to Daylight Saving Time in the spring and fall. For areas that do not recognize
DST changes (Arizona and parts of Indiana) turn the DST “OFF”.
RADIO-CONTROLLED TIME SETTING
1.
The word ON will start flashing in the lower LCD display.
5
2.
3.
Press and release the + key to select radio-controlled time ON or OFF.
Press and release the SET key to confirm the radio-controlled time setting and continue to
the Language setting.
Note: Turn off the radio-controlled time feature only if you DO NOT want the clock to
automatically update itself.
LANGUAGE SETTING
The weekdays can be displayed in LCD2 with the pre-set languages: US English (ENG), French
(FRA) and Spanish (ESP).
1.
LAN will be displayed in the lower LCD along with one of the three letter language
abbreviations.
2.
3.
Press and release the + key to select the desired language.
Press and release the SET key to confirm the language setting and enter the Manual Time
setting mode.
MANUAL TIME SETTING
In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting
distance, etc.), the time can be manually set. The clock will then work as a normal Quartz clock.
1.
2.
3.
4.
5.
The hour digits will start flashing in the upper LCD.
Select the desired hours by pressing and releasing the + key.
Press and release the SET key to advance to the minutes setting.
Now the minute digits will start flashing.
Select the desired minutes by pressing and releasing the + key. If the + key is held, the units
will increase by 5.
6
6.
Press and release the SET key to confirm the Time setting and continue to the Year setting.
Note:
The unit will still try to receive the signal every day despite it being manually set. When it does
receive the signal, it will change the manually set time into the received time. During reception
attempts the WWVB tower icon will flash. If reception has been unsuccessful, then the WWVB
tower icon will not appear but reception will still be attempted the following hour.
WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB
reception every full hour within this time frame). When the time signal is received for example at
1:00 am, the atomic clock will not attempt to receive the WWVB signal for the remaining hours
until 6:00 am. Therefore, the next signal attempt will take place between 12:00 am and 6:00 am
the next day. The other times WWVB reception takes place, are upon setup and after manual time
set exiting mode. Reception is generally not possible during daylight hours due to the interference
of the sun.
YEAR SETTING
The year can be selected sequentially from 2003 to 2029 and will then start over again (default
setting 2004). None of the digits of the year will be visible on the lower LCD display however the
year must be correct as it affects the day of the week display.
1.
2.
3.
The year digits will start flashing in the lower LCD.
Press and release the + key to select the desired year.
Press and release the SET key to confirm the Year setting and continue to the Month
setting.
MONTH SETTING
1.
2.
3.
The month digits on LCD2 will start flashing.
Press and release the + key to select the desired month.
Press and release the SET key to confirm the Month setting and continue to the Date
setting.
DATE SETTING
1.
2.
3.
The digits for the date will start flashing in the lower LCD (Default setting 1).
Press and release the + key to select the desired date.
Press and release the SET key to confirm the Date setting and exit the manual setting
mode.
7
Note: The date can only be set in conjunction with the selected month. For example, it is not
possible to set the date 30 if the month of February is selected.
EXIT THE MANUAL SETTING MODES
•
To return to the normal display mode from anywhere in manual setting mode simply press
the ALM key at anytime.
•
If no keys are pressed for at least 15 seconds in setting mode, the atomic clock will
automatically switch back to normal display mode.
ALARM SETTING
To enter into the alarm setting mode:
1.
2.
3.
4.
5.
6.
Hold the ALM key for 5 seconds. The hour digits start flashing.
Press and release the + key to set the hour.
Press and release the ALM key to continue to the minutes setting.
The minute digits start flashing.
Press and release the + key to set the minutes.
Press and release the ALM key to exit the Alarm setting mode or wait for 15 seconds for the
clock to automatically timeout and return to the standard display mode.
TO DEACTIVATE THE ALARM:
Alarm icon (((•))) (ON)
The alarm will be automatically switched ON when the alarm time is set. To deactivate the alarm
(OFF), press and release once the ALM key in normal mode display. The alarm icon will
disappear, the alarm is now off.
SNOOZE SETTING
The snooze can only be activated during alarm time for a snooze duration of 10 minutes by
pressing the SNZ key.
8
WWVB RADIO CONTROLLED TIME
The NIST radio station, WWVB, is located in Ft. Collins, Colorado and transmits the exact time
signal continuously throughout the United States at 60 kHz. The signal can be received up to
2,000 miles away through the internal antenna in the atomic clock. However, due to the nature of
the Earth’s Ionosphere, reception is very limited during daylight hours. The atomic clock will
search for a signal every night when reception is best. The WWVB radio station derives its signal
from the NIST atomic clock in Boulder, Colorado. A team of atomic physicists continually
measures every second of every day to an accuracy of ten billionths of a second a day. These
physicists have created an international standard, measuring a second as 9,192,631,770
vibrations of a Cesium 133 atom in a vacuum. This atomic clock regulates the WWVB transmitter.
The WWVB tower icon in the clock display will start flashing in the top center of the LCD. This
indicates that the clock has detected a radio signal and is trying to receive it. When the time code
is received, the WWVB tower becomes permanently lit and the time will be displayed.
If the tower icon flashes, but does not set the time or the WWVB tower does not appear at all, then
please take note of the following:
•
Recommended distance to any interfering sources like computer monitors or TV sets is a
minimum of 6 feet (2 meters).
•
Within ferro-concrete rooms (basements, superstructures), the received signal is naturally
weakened. In extreme cases, please place the unit close to a window and/ or point its front or
back towards the Fort Collins, Colorado, transmitter.
•
During nighttime, the atmospheric disturbances are usually less severe and reception is
possible in most cases. A single daily reception is adequate to keep the accuracy deviation
below 1 second.
Note:
In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting
distance, etc.), the time can be manually set (please refer to notes on Manual time setting).
MOON PHASE
The moon phases appear in the middle of the lower LCD. There are 12 visible Moon Phases that
will show in the LCD:
9
MOON PHASES FOR THE WS-8236U
New Moon
Small Waxing
Crescent
Large Waxing
Crescent
First Quarter
Small Waxing Large Waxing
Gibbous
Gibbous
Full Moon Large Waning
Gibbous
Small Waning Last Quarter
Gibbous
Large Waning
Crescent
Small Waning
Crescent
POSITIONING
Before permanently mounting ensure that the atomic clock is able to receive WWVB signals from
the desired location. Also, extreme and sudden changes in temperature will decrease the
accuracy of the atomic clock, and changes in elevation will result with inaccurate temperatures
readings for the next 12 to 24 hours. These changes will require a 12 to 24 hour wait before
obtaining reliable data.
POSITIONING THE ATOMIC CLOCK:
There are two possible ways to mount the atomic clock:
•
•
use of the foldout table stands, or
wall mounting
FOLDOUT TABLE STAND
The foldout table stand legs are located on the backside, at the lower corners, just
below the battery cover. The hinges are towards the edges of the atomic clock, and
the ends (with no hinge) need to be folded out towards the edge. Once the foldout
table stands are extended, place the atomic clock in an appropriate location.
10
WALL MOUNTING
1) Using a straight edge, horizontally space at about 2“ (50 mm) three screw
positions on a wall.
2) Install three mounting screws (not included) into a wall —leaving
approximately 0.19“ (5mm) extended from the wall.
3) Place the atomic clock onto the screws, using the hanging holes on the
backside. Gently pull the atomic clock down to lock the screws into place.
Note:
Always ensure that the atomic clock locks onto the screws before releasing.
TROUBLESHOOTING
Problem:
Solution:
Problem:
Solution:
The LCD is faint.
1) Replace the batteries.
No reception of WWVB signal
1) It may help reception to face the front of the atomic clock in the general
direction of Ft. Collins, Colorado.
2) Wait overnight for signal.
3) Be sure the atomic clock is at least 6 feet (2 meters) from any electrical
devices, i.e. TV sets, computers, or other radio controlled clocks.
4) Remove batteries for five minutes, reinsert and leave the unit alone
overnight without pressing any keys.
Problem:
Solution:
Problem:
Solution:
Hour is incorrect (minute and date are correct).
1) Be sure the correct time zone and daylight saving time are selected.
"OFL“ appears in the indoor temperature section of the LCD
1) Move the atomic clock to an area with warmer or cooler surrounding
temperature. Current surrounding temperatures are outside measuring
range.
CARE AND MAINTENANCE:
•
•
Avoid placing the unit in areas prone to vibration and shock as these may cause damage.
Avoid areas where the unit can be exposed to sudden changes in temperature, i.e. direct
sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes which
reduces the accuracy of readings.
11
•
When cleaning the LCD and casing, use a soft damp cloth only. Do not use solvents or
scouring agents.
•
•
Do not submerge the unit into water.
Immediately remove all low powered batteries to avoid leakage and damage. Replace only with
new batteries of the recommended size.
•
Do not make any repairs to the unit. Please return it to the original point of purchase. Opening
and tampering with the units may invalidate the warranty.
SPECIFICATIONS:
Indoor temperature measuring range :
+14.1ºF to +99.9ºF with 0.2ºF resolution
every 15 seconds
0 to 99%
Temperature checking interval
Indoor humidity measuring range
Humidity checking interval
:
:
:
every 20 seconds
Power source (Alkaline batteries recommended) :
3 x AA, 1.5V batteries
about 12 months
9.5“ x 9.25“ x 1.16“ / 240.4 x 236 x 29.5mm
Battery life
Dimensions (H x W x D)
:
:
LIABILITY DISCLAIMER:
•
The manufacturer and supplier cannot accept any responsibility for any incorrect readings and
any consequences that occur should an inaccurate reading take place.
•
•
•
•
•
This product is only designed for use in the home or office.
This product is not to be used for medical purposes or for public information.
The specifications of this product may change without prior notice.
This product is not a toy. Keep out of the reach of children.
No part of this manual may be reproduced without written authorization of the manufacturer.
BATTERIES CHANGE:
For best performance, batteries should be replaced at least once a year to maintain the best
running accuracy. Ensure that the batteries used are new and the correct size.
Please help in the preservation of the environment and return used batteries to
an authorized depot.
12
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against
manufacturing defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased
and used in North America and only to the original purchaser of this product. To receive warranty
service, the purchaser must contact La Crosse Technology, Ltd for problem determination and
service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd
authorized service center. The original dated bill of sale must be presented upon request as proof
of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service
center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as
stipulated herein, with new or reconditioned parts or products if found to be defective during the
limited warranty period specified above. All replaced parts and products become the property of
La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement
parts and products assume the remaining original warranty, or ninety (90) days, whichever is
longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs
covered by this warranty. If necessary repairs are not covered by this warranty, or if a product is
examined which is not in need or repair, you will be charged for the repairs or examination. The
owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product
to a La Crosse Technology, Ltd authorized service center. La Crosse Technology, Ltd will pay
reasonable return shipping charges to the owner of the product.
Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the
following specified exceptions: (1) damage caused by accident, unreasonable use or neglect
(including the lack of reasonable and necessary maintenance); (2) damage occurring during
shipment (claims must be presented to the carrier); (3) damage to, or deterioration of, any
accessory or decorative surface; (4) damage resulting from failure to follow instructions contained
in your owner’s manual; (5) damage resulting from the performance of repairs or alterations by
someone other than an authorized La Crosse Technology, Ltd authorized service center; (6) units
used for other than home use (7) applications and uses that this product was not intended or (8)
the products inability to receive a signal due to any source of interference.. This warranty covers
only actual defects within the product itself, and does not cover the cost of installation or removal
from a fixed installation, normal set-up or adjustments, claims based on misrepresentation by the
seller or performance variations resulting from installation-related circumstances.
13
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE
OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED
FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY.
KEEP OUT OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights specific to your
State. Some States do no allow the exclusion of consequential or incidental damages therefore
the above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology, Ltd
2809 Losey Blvd. S.
La Crosse, WI 54601
Phone: 608.782.1610
Fax: 608.796.1020
e-mail:
(warranty work)
(information on other products)
web:
Questions ? Instructions? Please visit:
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or
duplicated or processed using electronic, mechanical or chemical procedures without written
permission of the publisher.
This handbook may contain mistakes and printing errors. The information in this handbook is
regularly checked and corrections made in the next issue. We accept no liability for technical
mistakes or printing errors, or their consequences.
All trademarks and patents are acknowledged.
14
|