SecureTraveler™ User’s Manual
SecureTraveler™ is the DataTraveler® configuration utility that allows corporate and home users
to set up public and password-protected privacy zones on compatible DataTraveler USB Flash
Drives. It also allows users to set Windows shortcuts to launch the program conveniently.
This document is designed to get you started with SecureTraveler and includes important frequently
asked questions (FAQs). For the latest FAQs, please visit the DataTraveler® website at
www.kingston.com/support/USBFLASHDRIVES .
Document No: 4808056-001.A00
Secure Traveler User’s Manual
1
1
SYSTEM
1.1 Requirements
• Pentium II 266 MHz Processor
• 2MB hard drive free space
• Operating Systems: Windows Vista™ (32-bit only)*, Windows XP® SP1 and SP2, Windows
2000® SP4
• Administrative privileges for Windows XP and 2000.
• USB Port 2.0/1.1
* Windows ReadyBoost not supported.
1.2 Recommendations
• Graphic accelerator that supports 24-bit color depth for best-quality graphics
2
PUBLIC AND PRIVACY ZONES
The DataTraveler® can be set up for a public zone only, or a public and privacy zone. A public
“zone” refers to the area on the DataTraveler® that is not protected. By default, Kingston sets up
the entire DataTraveler as a public zone at the factory. Files in the public zone can be seen and
read on USB-ready computers; there is no data security in the public zone.
DataTraveler listed as 1GB of capacity1 will be set up as a single zone by default (Figure 1):
Figure 1: Single Zone
1
Please note: Some of the listed capacity is used for formatting and other functions and thus is not available for data storage. For more information, please
consult Kingston’s Digital media Guide at Kingston.com/Digital_Media_Guide.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
3
If the SecureTraveler™ is used to format and create a privacy zone, then a 1GB DataTraveler could be
divided as follows (Figure 2):
Figure 2: Divided Zone
In the previous example (Figure 2), the total available data storage area is broken up as:
-Privacy partition of 363 MB
-Public partition for the remainder, or 984 MB – 363 MB = 621 MB.
Files in the privacy zone cannot be accessed without entering a password set up by the person who
set up the privacy zone. Privacy zones thus offer data security for private data. Without a
password, there is no way to even view the file names stored in the privacy zone, let alone the files
themselves.
This User Guide will explain how to set up public and private partitions for increased data security,
as well as setting up Windows shortcuts to allow for faster and easier access to the SecureTraveler
program.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
4
®
3
CONNECTING THE DATATRAVELER
Insert your DataTraveler USB Flash drive into the USB port. The Operating Systems will
automatically recognize the DataTraveler and install the required drivers.
Generally, Windows will display the contents of the public zone of the DataTraveler (Figure 3).
Figure 3: DataTraveler Public Zone Contents
If you do not need a privacy zone for data security, you can use the DataTraveler without running
SecureTraveler™.
For computers running supported Microsoft Windows: If you’d like to set up a privacy zone,
double-click on the SecureTraveler™ executable program (Figure 3). Section 4 will describe
the use of the SecureTraveler program.
Note: SecureTraveler software is not supported on Macintosh systems.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
5
®
™
4
CONFIGURING THE DATATRAVELER WITH SECURETRAVELER
CAUTION! When you create or update a privacy zone, the DataTraveler® is formatted and
ALL data stored on the drive will be lost. Backup your files before you create or change your
privacy zone. SecureTraveler will save the SecureTraveler.exe file; however, you will need to
save the User Guide to your hard drive prior to any format changes.
4.1 Creating the Privacy Zone
When the SecureTraveler™ program is executed, a Language Selector screen will appear (Figure 4):
Figure 4: SecureTraveler Language Selector
If English is OK for the program language, click the OK button to continue. To prevent this screen
from showing up every time you run the DataTraveler®, please check the box next to the Don’t
show this message next time; note that you can still change this option and the language on the
Formatting screen.
To change the language, click on the language display to show all available languages and
highlight the desired language before clicking the OK button (Figure 5). You can also check Don’t
show this message next time if desired.
Figure 5: SecureTraveler Languages List
Document No: 4808056-001.A00
SecureTraveler User’s Manual
6
Next, the Welcome Screen is displayed, explaining that there is no privacy zone defined (Figure 6):
Figure 6: SecureTraveler Welcome Screen
Click Cancel to exit SecureTraveler or OK to continue to the Format screen (Figure 7).
Figure 7: SecureTraveler Format Screen
The Format screen allows you to define the size of the privacy zone and password used to access it.
To set the password, which is required for the privacy zone, enter it in the Password and Confirm
Password fields; both passwords keyed in must match exactly for SecureTraveler to accept the
password. This password can be changed later in the Settings screen.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
7
The Hint field, which is optional to fill in, is there to help you remember a password should you
forget it.
CAUTION! If you forget your privacy zone password, you will no longer be able to access
files stored in the privacy zone; you will be required to reformat and reinitialize the privacy
zone to regain the original space, thereby losing all the files stored there. This is done to
protect the data – you cannot access it without the password defined by the creator of the
privacy zone.
Next, click on the slider bar with your mouse (Figure 8), and while holding down the left mouse
key, drag the pointer to correspond to the desired split between public and privacy zones. The
privacy zone can only be set up to 90% of the capacity of the flash drive shown on the screen. The
selected area for the privacy zone will be highlighted in green on the DataTraveler graphic.
Slider bar
Figure 8: SecureTraveler Formatting Slider Bar
After selecting the privacy zone size, click OK to continue. If you do not wish to make any
changes, click Cancel to exit this screen.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
8
In the example, a 1 GB DataTraveler is set up to have about 500MB allocated for privacy zone
(Figure 9).
Figure 9: Format Screen with Privacy Zone
Due to different DataTraveler capacities, SecureTraveler may make slight adjustments to the user-
selected privacy zone size to optimize the internal storage division; so, if you select 501.50 MB for the
privacy zone, SecureTraveler will increase it to 506.50 MB for best fit with a 1GB DataTraveler drive.
When ready, click OK to proceed with the format, or click Cancel to exit this screen without
making any changes.
If there are no errors, SecureTraveler will ask for confirmation before proceeding with the actual
format (Figure 10).
Figure 10: Format Warning Screen
Click Cancel to cancel the Formatting, or OK to continue with the format.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
9
SecureTraveler will then initiate the format to create the privacy partition, and display a format
status window (Figure 11).
Figure 11: Format Status Window
When the formatting has completed successfully, you will see a Format Completed screen
(Figure 12):
Figure 12: Format Completed Window
Click OK to continue. At this point, the privacy zone formatting process is completed and you are
shown the Login screen to get into the privacy partition. Click Cancel to exit the program, or
enter the Password you just defined to access the privacy zone. Accessing the privacy Zone is
explained in the next section.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
10
4.2 Accessing Your Privacy Zone
When you insert the DataTraveler® into a compatible computer, it will be detected and a window
will display with the contents of the public zone as shown in Section 3 (Figure 3).
To access the privacy zone, do one of the following:
A. Double-click on the SecureTraveler executable file name shown for the DataTraveler
in Section 3 (Figure 3).
B. Click once on the task bar “Quick Launch” shortcut for SecureTraveler™ or double-
click on the workspace shortcut (if set up in the Format screen; see Section 4.3 for
details on these shortcuts, Figures 19 and 20).
If a privacy zone does not exist, the screen flow will start as shown in Section 4.1 as
SecureTraveler will assume that you are trying to define a privacy zone.
If a privacy zone exists, you will be asked to login using the password you defined in Section 4.1
(Figure 13):
Figure 13: SecureTraveler Login
Note: You can only access one zone at a time. Prior to logging into your privacy zone, you
will only be able to access the public zone. After you log into your privacy zone, you will be
able to access it but not the public zone. To re-access the public zone, you will need to log
out of your privacy zone first.
Enter your password and click OK to continue, or Cancel to exit SecureTraveler. If you enter your
password incorrectly, you will get an error message. SecureTraveler allows up to 5 password
verification attempts. If the privacy zone becomes blocked for further access, follow the directions
provided in the dialog boxes to access your privacy zone.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
11
If you forgot your password, click on the Hint reminder at the bottom; this will display your
predefined hint (Figure 14).
Figure 14: Privacy Zone Login Screen, Displaying Hint
Note: If you do not know or remember your password, the only option will be to reformat
the DataTraveler and create a new privacy zone. Warning, all data stored in the previous
privacy zone will be lost. See section 4.3 on formatting the DataTraveler drive.
When you enter the correct password, after a short time a successful login message is displayed
(Figure 15).
Figure 15: Successful Login Screen
You have the option of not showing the Successful Login Screen. You can check the Don’t show
this message next time box. This option can also be set/reset on the Settings screen.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
12
After successful login, Windows will open a new screen and display the contents of your privacy
zone (Figure 16).
Note: privacy zone is empty right after it is created.
Figure 16: Windows Privacy Zone Screen
Note that you will need to double-click on the Logout Privacy Zone to end access to the privacy
zone, or on the desktop shortcut to log out if set up in the Settings screen. You need to log out to
access the public zone if needed or to end your session and disconnect your DataTraveler.
When you are done, double-click on Logout Privacy Zone. After a short time, you will see the
Logout Verification screen (Figure 17).
Figure 17: Logout Verification Screen
Document No: 4808056-001.A00
SecureTraveler User’s Manual
13
To prevent file damage or loss, please close all application programs accessing the DataTraveler
and then click OK to close the privacy zone. Do not disconnect your DataTraveler drive.
Note that this screen can also be checked off so that it does not show up during logouts (the Don’t
Show option can be set or reset on the Settings screen).
After a short time, Windows will display the public partition (in this case, only containing the
SecureTraveler software) as shown in section 3 (Figure 3). At this time, you can access the public
zone or end your session and disconnect your DataTraveler.
To end your session and disconnect your DataTraveler, you will need to close the public partition
Window. Use the Unplug or Eject Hardware utility to safely remove the drive. This utility is
located in the System Tray next to the time/date. Click on the utility icon and then click on Safely
Remove Storage Device. Wait for notification that it is safe to remove your drive.
4.3 Customizing SecureTraveler™ Settings
When you run the SecureTraveler program, you can click on the Settings button (Figure 18) to see
the main Settings screen (Figure 19).
Figure 18: Settings Button
On the left side of the screen, you can check the boxes to set Windows options (Figure 19):
Figure 19: Settings Screen
Document No: 4808056-001.A00
SecureTraveler User’s Manual
14
• Create Shortcut in Quick Launch bar: Checking this box sets up an icon for
SecureTraveler in your Windows Quick Launch bar (Figure 20).
Figure 20: Quick Launch Shortcut
You can launch SecureTraveler by clicking once on this icon.
• Create Shortcut on Desktop: A SecureTraveler™ icon will be added to your desktop
(Figure 21).
Figure 21: SecureTraveler Shortcut on Windows Desktop
• No Login Confirmation: If No Login Confirmation is checked, you will not see this
screen upon login (Figure 22):
Figure 22: Login Confirmation Screen
Document No: 4808056-001.A00
SecureTraveler User’s Manual
15
• No Logout Confirmation: If No Logout Confirmation is checked, you will not see this
screen upon logout (Figure 23):
Figure 23: Logout Confirmation Screen
• SecureTraveler Language: By clicking on the Language field, you can select the
language used for the SecureTraveler™ program (Figure 24).
Figure 24: Language Selection Drop-down Menu
You can move the mouse over the different check boxes or the Language selection field, and the
Description field will show help information, explaining what the check boxes do. On the right, the
DataTraveler® graphic is shown, with the total size, and the size of the privacy zone as previously
defined for a 1GB DataTraveler.
Click OK to make changes, or click Cancel to return to the Login screen without making any
changes.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
16
You can change the format of the DataTraveler by clicking on the Format button. You will then
be presented with the Format screen (Figure 25).
Figure 25: Format Screen
CAUTION! Changing the size of your Privacy Zone requires formatting your DataTraveler,
causing ALL secured and non-secured data to be lost.
Please see Section 4.1 for details on changing your public and privacy zones.
Click on Change Password if you want to change the password to access the privacy zone. The
Change Password screen will appear (Figure 26). Frequent password changes are recommended
for improved security.
Figure 26: Password Change Screen
Document No: 4808056-001.A00
SecureTraveler User’s Manual
17
First, key in the Old Password (which is required to change to a New Password). If you don’t
remember or know the password, the privacy zone cannot be accessed and requires a new Format
to set up a new privacy zone.
Note: Formatting will delete all files stored in a previously defined privacy zone.
After entering the Old Password, followed by the New Password and then Confirm New
Password, you can enter a new Hint as a password reminder.
When ready, click OK to continue with the Password change or click Cancel to return to the
Settings screen. If the password is changed successfully, you will see the following screen
(Figure 27):
Figure 27: Password Change Confirmation
You can now exit SecureTraveler and use the DataTraveler to carry your information, with the
assurance that the privacy zone will help protect it from unauthorized access.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
18
5
FREQUENTLY ASKED QUESTIONS
For a complete list of the latest FAQs, go to the DataTraveler website at
www.kingston.com/support/USBFLASHDRIVES. Several FAQs are listed below for your
convenience.
Q: I would like to secure all the data on my DataTraveler. Why am I limited to a
Maximum Privacy Zone of 90%?
A: Your DataTraveler needs space to run SecureTraveler, as well as information about your
DataTraveler. 10% of your DataTraveler is kept free to save space for upgrades and future
applications without hindering SecureTraveler operation.
Q: How do I switch between the Public Zone and my Privacy Zone?
A: Launch SecureTraveler from your desktop, DataTraveler or quick launch bar. If you see a
prompt asking for your password, this means that you are currently in the Public Zone. To
switch to your Privacy Zone, enter your password and click OK. If you see a pop-up window
with a prompt asking you for logout confirmation from your Privacy Zone, this means that
you're working in your Privacy Zone. To switch, click OK. To remain logged into your
Privacy Zone, click Cancel.
Q: I accidentally deleted SecureTraveler™ from my DataTraveler. How can I access data
in my Privacy Zone?
A: Download a new copy of SecureTraveler from the web at
www.kingston.com/support/USBFLASHDRIVES to your DataTraveler. The Privacy Zone
that you previously designated will be accessible.
Q: Why can’t I see the public partition after logging into the privacy partition?
A:
You can’t access or see both partitions at the same time. You need to log out of the privacy
partition to see the public partition, just like you need to log in to see the privacy partition.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
19
Q: Can I disconnect my DataTraveler without logging out of the privacy partition?
A: Yes, you can disconnect the DataTraveler without logging out of the privacy zone. However,
to protect your data, Kingston recommends that you log out of the privacy zone prior to
disconnecting the DataTraveler.
Q: Why can I use SecureTraveler only on certain Windows 2000 or Windows XP
computers?
A: You can only use SecureTraveler on computers with administrative privileges.
Q: How do I delete the privacy zone?
A: To delete the privacy zone, you must reformat the DataTraveler via the SecureTraveler
application and set the privacy zone size to 0 MB. This renders the drive 100% public,
deleting the privacy zone.
Note: All data will be lost! Backup important files prior to formatting.
Q: Can I use more than one DataTraveler with the SecureTraveler simultaneously?
A:
No. SecureTraveler can only access one drive at a time.
Document No: 4808056-001.A00
SecureTraveler User’s Manual
20
|