CD PLAYER
CD/DPF-R SERIES
DPF-R6010
DPF-R4010
DPF-R3010
CD-206
CD-204
CD-203
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction m anual is used for six m odels. Model availability and features
(functions) m ay differ depending on the country and sales area.
DTS disclaimer clause
When Playing DTS-encoded CDs, excessive noise w ill be exhibited from the analog
stereo outputs. The consum er should take proper precautions w hen the analog stereo
outputs of the CD player is connected to an am plification system . To enjoy DTS
Digital Surround playback, an external 5.1 channel DTS Digital Surround decoder
system m ust be connected to the digital output (S/ PDIF, ASE/ EBU, or TosLink) of the
CD player.
B60-3684-00 CH ( K,P,Y, M ,X ,T )
99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 3 2 1
ID
Introduction
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En
)
Unpacking
Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost.
3
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped
to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier
for shipping damage.
We recommend that you retain the original carton and packing materials for use should you transport or ship the unit in the future.
Keep this m anual handy for future reference.
Special features
CD-TEXT support (CD-206/ DPF-R6010 only)
¶
¶
The text information (disc title, track titles, names of the artists, songwriters, composers,
etc.) recorded on the CDs can be easily called and displayed in alphanumerics. (Some
words and text may not be displayed.)
@#
Advanced technologies incorporated in pursuit of im -
proved sound quality and stability (CD-206/ DPF-R6010
only)
D.R.I.V.E. (Dynamic Resolution Intensive Vector Enhancement) IC is built in for drastic
reduction of distortion at small signal level.
Convenient features for dubbing CD onto tape
¶
¶
¶
Normal EDIT: Edit function for rearranging tracks according to the tape length so that no
music is interrupted in the middle.
)
MULTI EDIT: Several CDs can be edited and recorded on 1 tape. (Except for CD-206/
DPF-R6010)
¡
^
Auto space function.
Easy operation functions
¶
Easy operation functions allow systematic operation with other KENWOOD components
connected through the system control connection.
5
Accessories
AC plug adaptor .............. (1)
Audio cord ............... (1)
System control cord ........... (1)
Use to adapt the plug on the power cord
to the shape of the wall outlet.
(Accessory only for regions where use is
necessary.)
Remote control unit .............. (1)
(Except for CD-203/DPF-R3010)
Batteries (R6/AA) ................. (2)
(Except for CD-203/DPF-R3010)
Caution: Read the pages m arked
carefully to ensure safe operation.
Contents
Displays ........................................................................... 13
Program m ed play (PGM m ode) ................................... 14
Playback in random order (Random playback) .......... 17
Repeated playback ........................................................ 18
Editing ............................................................................. 20
Norm al EDIT ................................................................ 20
MULTI EDIT ................................................................. 21
Tim er operations ........................................................... 23
Maintenance ................................................................... 24
In case of difficulty ........................................................ 25
Specifications ................................................................. 26
Introduction ..................................................................... 2
Before applying pow er ................................................... 2
Safety precautions ......................................................... 2
Special features ........................................................... 3
System connections ....................................................... 4
Controls and indicators .................................................. 6
Operation of rem ote control unit ................................. 8
Preparing to play tracks ................................................. 9
Norm al play (TRACK m ode) ........................................ 10
Searching for tracks by title (TITLE SEARCH) ........... 12
System connections
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En
)
Malfunction of microcomputer
If operation is not possible or erroneous display appears even though
all connections have been made properly, reset themicrocomputer
Caution:
4
Do not plug in the pow er lead until all connections are
com pleted.
referring to “In case of difficulty”.
∞
Make connections as show n below .
When connecting the related system com ponents, refer also
to the instruction m anuals of the related com ponents.
Digital component (MD, DAT, etc.)
(COAXIAL)
SL 16/XS8 switch 5
DIGITAL INPUT
(OPTICAL)
CD-206/ DPF-R6010 :
LINE OUTPUT
@
CONTROL
DIGITAL OUTPUT
COAXIAL
VARI ABLE SYSTEƒM
OPTICAL
L
SL16 XS
8
R
TEXT
To wall AC outlet
75Ω coaxial cable
with RCA PIN.
(Commercially-
available)
Remove the protection cap when using the
DIGITAL OUTPUT (OPTICAL) jack
Commercially-available
optical fiber cable
SYSTEM
CONTROL
CD
DIGITAL
INPUT
Digital amplifier
(or ordinary amplifier, receiver, etc.)
L
R
COAXIAL OPTICAL
System control cord
Audio cord
CD-204/ 203/
DPF-R4010/ R3010 :
SYSTEM
CONTROL
LINE OUTPUT
ƒ
L
R
SL1 6 XS
8
To wall AC outlet
SL 16/XS8 switch 5
Connection to digital amplifier or MD (CD-206/DPF-R6010 only)
Connect the DIGITAL OUTPUT (OPTICAL or COAXIAL) jack to the digital input jack of the am plifier, DAT recorder, MD recorder,
etc., using an optical fiber cable or coaxial cable w hich are com m ercially available in audio stores.
÷When using an optical fiber cable to connect this unit to a digital
amplifier, insert the plug straight into the jack until a snap sound is
Optical fiber cable
heard.
÷Be careful not to bend, coil, or bundle the optical fiber cable.
÷Optical fiber cables available on the market may not always be able to
be used with this player. If your cord cannot be used with this unit,
consult the store from which you purchased the cord or your nearest
dealer.
1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced.
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection
cords without removal of the power cord can cause malfunctions or damage to the unit.
NNootteess
System connections
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En
)
SYSTEM CONTROL CONNECTIONS
5
Amplifier or receiver
Connecting system control cords after connecting a KENWOOD
audio com ponent system lets you take advantage of convenient
system control operations.
SYSTEM
CONTROL
There are tw o KENWOOD system control m odes. Make connec-
tions according to the groups of term inal sym bols show n below .
This unit
[XS 8] Mode : lets you com bine F, f, and ƒterm inals
SYSTEM
CONTROL
[SL16] Mode : for
term inals only
This unit is com patible w ith both [XS8] and [SL16] m odes.
Select the m ode according to the connected com ponents. 4
Cassette deck
j
SYSTEM
CONTROL
SL1 6 XS 8
÷Do this operation after completing all connections.
(Ensure that the unit is set to STANDBY mode.)
NNootteess
1. If your amplifier or receiver does not have a system control terminal, do not
connect any system control cords to the system control terminals on the other
components.
2. Do not connect system control cords to any components other than those
specified by KENWOOD. It may cause a malfunction and damage your
equipment.
3. Be sure the system control plugs are inserted all the way in to the system
control terminals.
SYSTEM CONTROL OPERATIONS
Rem ote Control
Lets you operate this unit with the system remote control unit supplied with the amplifier or receiver.
Autom atic Operation (Except [XR] equipm ent)
Automatically switches the input selector on the amplifier or receiver when you start playback from this unit.
Synchronized Recording (Except [XR] equipm ent)
Lets you synchronize recording with the start of playback when recording from a CD. Also, the simple CCRS operation enables great recordings from
CDs.
See the operating instructions supplied with your cassette deck for details.
To use the headphone (Except for CD-203/DPF-
Adjusting the output levels of the output jacks
andheadphone output(ExceptforCD-203/DPF-
R3010)
The OUTPUT level (UP/ DOWN) keys of the rem ote control
unit can adjust the output levels from the LINE/ OUT and
PHONES jacks of the unit.
R3010)
Connect a stereo headphone to the PHONES jack of the CD
player. Adjust the sound volum e using the rem ote control
unit.
CD-206/ DPF-R6010
Output level
OUTPUT
OUTPUT -12dB
DOW N
UP
CD-204/ DPF-R4010
1
6
2
7
3
8
4
9
5
1 0
_1 2 d b
Output level
÷It is not favorable for the sound quality to decrease the output level from
this unit too much. Use these keys for coordination with other line
levels.
÷Adjusting the headphone output level also changes the LINE/OUT
level. Do not adjust the output level from this unit particularly during
recording.
÷Please note that the sound output is at the maximum level when the
power is turned on.
Controls and indicators
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
6
CD-206/ DPF-R6010
(The displays given in this manual are approximations only. They
may differ from what actually appears on the display.)
Play indicator
Text information display
••• •• •• •• •• •• ••
Pause indicator
CD-204/ 203/ DPF-R4010/ R3010
EDIT indicator
RANDOM indicator
P.C. indicator
ALL indicator
Music calendar (1 ~ 20)
REPEAT indicator
Program mode indicator
RANDOM
MULTI
EDIT
PGM
P.C.
ALL
1
2
3
4
5
DISC
NO.
REPEAT
TRACK NO.
Play indicator
Pause indicator
SINGLE
TOTAL
6
7
8
9
1 0
1 5
2 0
A
B
1 1
1 6
1 2
1 7
1 3
1 8
1 4
1 9
1
2
3
4
5
8
8 8 _8 8:8 8
Disc No. indicators
Time counter, Program No.
(SINGLE, TOTAL)
TRACK NO. indicator
The illustration of the com m on parts
is of CD-206/ DPF-R6010.
Except for USA
CD-204/ 203
DPF-R4010/ R3010
and Canada
CD-204/ 203
DPF-R4010/ R3010
DISPLAY
CHECK
CLEAR
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
-ON –STANDBY
1
2 3
4 5
6
7
8 9
MULTIPLE CD PLAYER DPF-R6 0 1 0
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
4
1
¢
TEXT DISP. ALL INFO.
POWER
P.MODE TIME DISP.
RANDOM REPEAT
EDIT
¡
0
DISC SKIP
-ON –STANDBY
6
7
COMPACT
PHONES
D.R.I.V.E.
DIGITAL AUDIO
TEXT
$
% ^
&
*
0 ! @
#
About the STANDBY mode
When the power cord of this unit is plugged into an AC outlet, a small amount of current is being supplied to the unit even when the ON/STANDBY switch
is not depressed (–). This is called the STANDBY mode.
Controls and indicators
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
7
The keys w ith the sam e nam e as those on the rem ote control
unit operate the sam e w ay as the rem ote control unit.
1 ON/ STANDBY (POWER /
Turns the unit ON/STANDBY.
2 P.MODE key
3 TEXT DISP. key (CD-206/ DPF-R6010 only)
Used to select the CD-TEXT information display.
CHECK key (CD-204/ 203/ DPF-R4010/ R3010 only)
Used to check or change program contents.
4 ALL INFO. key (CD-206/ DPF-R6010 only)
Used to display all text information on the CD.
CLEAR key (CD-204/ 203/ DPF-R4010/ R3010 only)
Used to clear the program.
) sw itch
9
9 Open/ Close key (0)
9
Opens and closes the disc tray.
0 RANDOM key
$
#
&
*
^
9
!
)
0
Press to play the tracks in a random order.
! REPEAT key
Press to play the tracks repeatedly.
@ TIME DISP. key
Press to switch the time indication mode.
# Disc tray
Load the disc to be played back.
$ Search keys (1,¡)
Fast forwards or fast reverses the track.
% EDIT m ode key
%
#
^
5
Rem ote control light sensor (CD-206/ 204/ DPF-R6010/
R4010 only)
8
!
Press to select the edit mode.
^ STOP key (7)
& PHONES jack (CD-206/ 204/ DPF-R6010/ R4010 only) 5
6 Skip keys (4,¢)
Press to skip to the beginning of another track.
7 Disc selector keys (DISC1 – DISC5) / Indicator (CD-206/
Use to connect (optional) headphones.
DPF-R6010 only)
Press to select the disc to be played.
8 DISC SKIP key
0
* PLAY/ PAUSE key (6)
0
Each tim e the ke y is pre s s e d, playback and paus e s w itch
each other.
9
Press to rotate the disc tray or to select the disc.
(Except for CD-203/DPF-R3010)
Operation of remote control unit
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
The illustration show s the RC-P0601.
The keys with the same name as those on the main unit operate the same way as on the main unit.
The keys marked * are provided only on the remote control unit.
8
1 Program -related and other keys
*3 OUTPUT (DOWN, UP) key
5
0
RANDOM key
REPEAT key
P.MODE key
TIME DISPLAY key
EDIT key
&
DISC SELECTOR
2
RANDOM
REPEAT
P.MODE
1
4
3
4
5
*
$
^
)
4 DISC SELECTOR keys
5 DISC SKIP key
90
5
2
DISC SKIP
1
1
3
*6 Num eric keys (1 ~ ), 0)
* CHECK key (CD-206/ DPF-R6010
only) %™
* CLEAR key (CD-206/ DPF-R6010
only) ^™
!
TIME
DISPLAY
4
7
5
8
6
6
7
7 Basic function keys
Stop key (7)
EDIT
9
0
0
!
!
TEXT
DISPLAY
CHECK
0
+1 0
6
Play/ Pause key (6)
Skip (4,¢) keys
Search keys (1,¡)
2 Selector keys relating to text infor-
m ation CD-206/ DPF-R6010 only)
2
3
CLEAR
ALL INFO.
TITLE
7
(
ALL TEXT
SEARCH SEARCH
* ALL TEXT SEARCH key
TEXT DISPLAY key
ALL INFO. key
9
#
#
@
4
1
¢
¡
OUTPUT
DOW N
UP
* TITLE SEARCH key
REMOTE CONTROL UNIT
RC-P0 6 0 1
CD-206/ DPF-R6010 :
M o d e l : R C - P 0 6 0 1
Infrared ray system
CD-204/ DPF-R4010 :
M o d e l : R C - P 0 5 0 4
Infrared ray system
Loading batteries
1 Rem ove the cover.
2 Insert batteries.
3 Close the cover.
2
2
1
1
÷Ins e rt tw o AA-s ize (R6) batte rie s as
indicated by the polarity marking.
Operation
Remote control
light sensor
After plugging in the power cord, press the ON/STANDBY (POWER/
) switch of the main unit to turn the unit ON. When the unit is
turned ON, press the key of the function to be operated.
6m
30°
30°
Operating range
(Approx.)
÷When pressing more than one remote control key successively, press
the keys securely by leaving an interval of 1 second or more between
keys.
REMOTE CONTROL UNIT
RC-P
0
6
0
1
1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries.
2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light sensor. In
such a case, change the system installation position to prevent the malfunction.
NNootteess
Preparing to Play Tracks
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
• Turn the unit ON.
Preparation
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
9
Press the ON/ STANDBY (POWER /
)key.
POW ER
-ON –STANDBY
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
Loading/unloading discs
1Load/unload a disc.
Open the tray.
1
0
Place/ rem ove a disc.
2
÷Do not touch the played side of disc.
÷Loading two discs together will cause malfunctioning.
÷Place the disc properly along the groove on the tray. (If the disc is not
placed horizontally, malfunction will result.)
Label side
÷A single CD (8 cm disc) can also be played.
÷Ordinary CD single (8 cm) disc adapters sold in audio stores cannot be
used with this unit.
Disc tray
When loading or unloading other discs
3
DISC SKIP
÷When loading/unloading a disc while the tray rotates, a malfunction
might occur. Load/unload the disc when the tray does not rotate.
2 Close the tray.
CD-206/ DPF-R6010
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
All DISC indicators "
" light regardless of how many discs are present.
0
CD-204/ 203/ DPF-R4010/ R3010
1
6
2
7
3
8
4
9
5
DISC
SINGLE
TRACK NO.
1 0
1
2
3
4
5
1
0 1 0:0 0
All DISC indicators " " light regardless of how many discs are present.
Remote control unit only
ALL TEXT SEARCH (CD-206/DPF-R6010 only)
For m ost CD-TEXT discs, it is convenient to read the com plete disc inform ation into the CD player before playing the disc.
This allow s text inform ation such as TITLE SEARCH, TEXT DISPLAY, ALL INFO., and other m essages to be displayed faster.
Search in progress or reading information
Blinks.
After loading all the discs, operate in stop m ode.
DISC READING
«
ALL TEXT
SEARCH
R
RC-P
D1 : CD TEXT
When the disc is CD-TEXT
÷The information read into the CD player is cleared when
the tray is opened. Therefore, perform this operation
again if the tray was opened.
÷Repeat the above procedure so that the complete disc information is
read into the CD player.
÷In the case of a non-CD-TEXT disc, the ”D1 : NO CD TEXT“ display will
appear for approx. 3 seconds.
Normal play (TRACK mode)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Use the follow ing procedure to play a CD in the original order
of tracks from track No. 1.
10
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
Playing tracks in order from track No. 1
Check that the unit is in the normal play TRACK
1
mode.
!
2Start playback.
CD-206/ DPF-R6010
If there is no disc in the selected disc tray, the corresponding
indicator "
" goes off.
Select the disc.
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Blinks during playback.
CD-204/ 203/ DPF-R4010/ R3010
or
If there is no disc in the selected disc tray, the corresponding
indicator " " goes off.
1
6
2
7
3
8
4
9
5
DISC SKIP
DISC
TRACK NO.
SINGLE
1 0
1
2
3
4
5
1
0 1 2:1 8
÷Playback starts from the disc selected in order of the DISC No.
÷When the 3/ 8 key is pressed without selecting a disc, playback starts
from the indicated DISC No.
CD-206/ DPF-R6010
Lights up.
01
Track NO. being
played
1:23
Elapsed time of track being played
÷In the case of a CD-TEXT disc, the disc’s title is scrolled on the display.
What is then displayed is in accordance with the TEXT DISPLAY mode.
#
CD-204/ 203/ DPF-R4010/ R3010
1
6
2
7
3
8
4
9
5
DISC
TRACK NO.
SINGLE
1 0
1
2
3
4
5
1
0 1 2:1 8
Track NO. being
played
Elapsed time of track being played
Disc indicator
during Playback (∞)
To pause playback
To stop playback
CD-206/ DPF-R6010
01
Lights up.
6
7
8
1
2
3
4
5
CD-204/ 203/ DPF-R4010/ R3010
÷Each press pauses and plays the CD alternately.
Normal play (TRACK mode)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
11
Playback from desired track
Select the disc.
1
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Select the desired track No.
2
Main unit
Remote control unit
Press the num eric keys as show n below ....
1
2
3
4
¢
To enter track No. 23 : 003
To enter track No. 40 : 0000)
4
7
5
8
0
6
9
÷Playback starts from the selected track and continues on the subse-
quent tracks.
+1 0
Skipping tracks
4
¢
To skip
backward
To skip
forward
÷The track in the direction of the pressed key is skipped, and the selected
track will be played from the beginning.
÷When the 4 key is pressed once during playback, the track being
played will be played from the beginning.
Searching
1
¡
Backward
search
Forward
search
÷Playback starts from the position where the key is released.
What is the “normal play TRACK mode”?
The norm al play TRACK m ode refers to the state in w hich the PGM, EDIT and RANDOM m ode displays are off.
To set the unit to the TRACK m ode:
Press the P.MODE key when the ”PGM“ or ”EDIT“ display is lighted.
Press the RANDOM key when the ”RNDM“ display is lighted.
CD-206/ DPF-R6010
Goes off.
Goes off.
Goes off.
PGM01 EDIT RNDM
CD-204/ 203/ DPF-R4010/ R3010
RANDOM
P.MODE
Goes off.
Goes off.
Goes off.
RANDOM
EDIT
PGM
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
(CD-206/DPF-R6010 only)
Searching for tracks by title (TITLE SEARCH)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
In the case of a CD-TEXT disc, the tracks to be heard can be
searched by title.
12
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
÷Load a disc (CD-TEXT support) in the CD
player.
Preparation
÷Check that the unit is in the normal play
TRACK mode.
÷Press the ALL TEXT SEARCH key.
!
9
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
1Press the TITLE SEARCH key.
Blinks.
TITLE
SEARCH
D1 01 TITLE ABC
Track title
REMOTE C
RC-P
0
1
÷When no CD-TEXT discs are loaded, the ”NO CD TEXT“ display will
appear for approx. 3 seconds.
To stop the search, press the
TITLE SEARCH key again.
2Select the name of the track (title) to be heard.
4
¢
D1 02 TITLE XYZ
If no keys are operated for more than a second, the track title is scrolled
on the display.
REMOTE CONTROL UNI
RC-P
0
6
0
1
The track number skips
backward.
The track number
skips forward.
3Start playback.
TITLE XYZ
|
The letters move toward the left.
6
REMOTE CONTROL UNIT
RC-P
0
6
0
1
02
Track NO. being played
1:23
Elapsed time of track being played
÷What is displayed will differ depending on the item which has been
selected by TEXT DISPLAY.
#
Display scrolling
Som e track titles contain so m uch text inform ation that the full
titles w ill not fit on the display. In cases like this, the letters on the
display m ove from right to left so that the non-visible part of the
title is revealed. This type of display m ovem ent is know n as
“scrolling display.”
Display example
0 1 C A B C D E F G H I J K L M N O P Q ...
|
Scroll display
0 1 L M N O P Q ...
(CD-206/DPF-R6010 only)
Displays
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
13
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
Selecting the text information display (TEXT DISPLAY)
In the case of a CD-TEXT disc, the displays show n below can
be selected.
In the stop m ode
When the key is pressed once, the 1 “Disc
Title” is scrolled on the display; w hen it is
pressed repeatedly, the display is changed.
(This operation cannot be perform ed in the
PGM m ode.)
1 Disc Title
2 Disc Artist
3 TIME
: Disc title
TEXT
DISPLAY
: Singer (or performer)
: Disc No., track No., time display
REMOTE CONTROL UNIT
RC-P
0
6
0
1
÷If the key is released while 2 ”Disc Artist“ is displayed, 1 ”Disc Title“
returns to the display.
In the play m ode
When the key is pressed once, the 1 “Track
Title” is scrolled on the display; w hen it is
pressed repeatedly, the display is changed.
Disc Title : AB
Scroll display
|
1
2
3
4
5
Track Title
:Track title
: ABCDEF...
Track Artist :Singer (or performer)
Disc Title
Disc Artist
TIME
:Disc title
:Singer (or performer)
:Track No., time display
÷When there is no text information to be displayed “–––––” is scrolled
on the display.
÷In the case of a non-CD-TEXT disc, the ”NO CD TEXT“ display will
appear for approx. 3 seconds.
÷If the key is released at any point while 2 ”Track Artist“ to 4 ”Disc
Artist“ is displayed, 1 ”Track Title“ returns to the display.
Displaying all the text information (ALL INFO.)
In the case of a CD-TEXT disc, the text inform ation show n below is displayed autom atically during norm al play (TRACK m ode).
Each item is displayed in turn each tim e the key is pressed.
When the key is repeatedly pressed w hile an item is being dis-
played, the display is forcibly m oved to the next item .
ALL INFO.
1
2
3
4
5
6
7
8
9
Disc/ Track Title : Disc and track titles
Disc/ Track Artist : Singer (or performer)
Disc/ Track Songw riter : Songwriter
Disc/ Track Com poser : Composer
REMOTE CONTROL UNIT
RC-P
0
6
0
1
| Scroll display
Disc/ Track Arranger
Disc/ Track Message
: Arranger
: Message from sponsor or artist
Arranger : ABCD
ID INFO.
: Record company, release date, etc.
: Genre information
Genre INFO.
ALL INFO. END : (Release)
To skip to the next track while the items are being displayed:
Press the ¢key.
÷The display can be returned to a previous item by pressing the 4
key.
÷Items from 1 to 6 are displayed in the sequence of disc and track.
÷When there is no text information to be displayed “– – – – –” is scrolled
on the display.
÷In the case of a non-CD-TEXT disc, the ”NO CD TEXT“ display will
appear for approx. 3 seconds.
Programmed play (PGM mode)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Use the follow ing procedure to program desired tracks in a
desired order. (up to 32 tracks)
14
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
Preparation
÷Load a disc in the CD player.
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
1 Press so that the “PGM” indicator lights.
Blinks.
CD-206/ DPF-R6010
Do this operation in the stop m ode.
PGM01 DISC?
P.MODE
CD-204/ 203/ DPF-R4010/ R3010
Light up.
PGM
1
2
3
4
5
2 Program desired tracks.
PGM01 D1 TNO.??
Select the disc.
1
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
In the case of a CD-TEXT disc, the disc title is scrolled on the display. (CD-206/
DPF-R6010 only)
Press the num eric keys as show n below ....
To enter track No. 25 : 005
CD-206/ DPF-R6010
Go to step 2 within 8 seconds.
PGM01 D1 TNO.25
«
Select the desired track No.
2
Main unit
Remote control unit
1
2
3
PGM01 ABCDEFGH
In the case of a CD-TEXT disc, the track's title is scrolled on the display.
4
¢
4
7
5
8
0
6
9
PGM01 D1 TNO.25
+1 0
CD-204/ 203/ DPF-R4010/ R3010
Go to step 3 within 8 seconds.
Set the entry.
PGM
5
DISC
TRACK NO.
3
1
2
3
4
5
1
2 5 P _ 0 1
Track number
P.MODE
÷Tracks can also be selected by pressing the 4or ¢ key.
÷Up to 32 tracks can be programmed. When “FULL” is displayed, no
more tracks can be programmed.
÷If you make a mistake, press the CLEAR key and enter the track No.
from the beginning.
Repeat steps 1, 2 and 3 above.
4
3 Start playback.
÷When the 4or ¢key is pressed during playback, the track will be
skipped in the direction of the pressed button.
÷When the 4key is pressed once during playback, the play position
returns to the beginning of the current track being played.
6
Programmed play (PGM mode)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
To stop playback
15
7
÷The programmed contents remain in memory.
To check or change the programmed tracks
CD-206/ DPF-R6010
Press the CHECK key.
1
Blinks.
CD-206/ DPF-R6010
PGM01 D5 TNO.25
CHECK
Press until the track
No. to be changed is
displayed.
REMOTE CONTROL UNIT
RC-P
0
6
0
1
CD-204/ 203/ DPF-R4010/ R3010
Light up
P.C.
CD-204/ 203/ DPF-R4010/ R3010
DISC
TRACK NO.
7
CHECK
5
2 5 P _ 0 1
Press until the track
No. to be changed is
displayed.
÷Perform only step 1 to simply check the program.
÷In the case of a CD-TEXT disc, the track's title is scrolled on the display.
(CD-206/DPF-R6010 only)
÷Each time the key is pressed, the program No. and the track No. on CD
Select the disc.
2
3
are displayed.
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Select the new track No.
Main unit Remote control unit
Example
1
2
3
≠
÷Press it while the “PGM 01” indicator blinks.(CD-206/DPF-R6010 only)
÷Press the key while the “P.C.” indicator is lit. (CD-204/203/DPF-R4010/
R3010 only)
4
¢
4
7
5
8
0
6
9
÷The track being played cannot be changed.
+1 0
Set the entry.
4
P.MODE
To add a track to the program
Select the disc.
1
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Select the desired track No.
Main unit Remote control unit
2
1
2
3
÷When a track No. is selected, the track will be added to the end of the
existing program.
4
¢
4
7
5
8
0
6
9
+1 0
Press the P.MODE key.
3
Programmed play (PGM mode)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
To clear tracks from the program
16
Press to clear tracks from the end.
CD-206/ DPF-R6010
÷Each time the key is pressed, the last track in the program is cleared.
÷The tracks which are programmed earlier than the track being played
cannot be cleared.
CLEAR
REMOTE CONTROL UNIT
RC-P
0
6
0
1
CD-204/ 203/ DPF-R4010/ R3010
CLEAR
To clear all tracks
P.MODE
÷Selected tracks can be also completely cleared just by operating the 0
key.
÷The entire program is cleared.
To program all tracks on a disc (CD-204/203/DPF-R4010/R3010 only)
Press so that the "PGM" indicator lights.
1
P.MODE
Select the desired disc.
2
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Press the P. MODE key again.
3
ALL indicator lights up.
P.MODE
1
6
2
7
3
8
4
9
5
ALL
1 0
P _ 0 1
Auto space function
During program m ing of tracks, a non-recorded space of a few
seconds w ill be autom atically created betw een tracks. By record-
ing tracks w ith these spaces on tape, the search and repeat play
operations of tape using the DPSS function (w hich w orks by
searching the non-recorded spaces) can be perform ed reliably.
÷Even when the performances of two tracks are continuous (which
occurs with classical or live recording music), the spaces will be
created if they have different track Nos.
Time display on CD player (TIME DISP.)
Each press of the TIME DISP. (TIME DISPLAY) key changes
the displayed contents.
CD-206/ DPF-R6010
Do this operation in the play m ode.
1
2
3
1:23 : Elapsed time of track being played
-2:23 : Remaining time of track being played
23:45T : Elapsed time of entire disc (T lights up.)
TIME DISP.
4 -36:25T : Remaining time on entire disc (T lights up.)
CD-204/ 203/ DPF-R4010/ R3010
1
1:23 : Elapsed time of track being played (SINGLE lights up.)
-2:23 : Remaining time of track being played (SINGLE lights
up.)
2
3
4
23:45 : Elapsed time of entire disc (TOTAL lights up.)
-36:25 : Remaining time on entire disc (TOTAL lights up.)
÷Only the display 1 and 2 will be displayed in PGM, RANDOM and EDIT
modes.
Playback in a random order (Random playback)
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
As tracks are selected at random , you can enjoy listening to
for a long tim e.
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
17
÷Load a disc in the CD player.
Preparation
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
Check that the unit is in the normal play TRACK
1
mode.
!
2Press the RANDOM key.
CD-206/ DPF-R6010
During track selection: ”>“ and ”<“ move from the outside to the
inside.
RANDOM
<<<><E12 ><>>>
The number here changes.
«
RNDM005
In case track No. 5 is selected
CD-204/ 203/ DPF-R4010/ R3010
Blinks
During random track selection
RANDOM
1
2
3
4
5
DISC
NO.
TRACK NO.
6
7
8
9
1 0
1 5
2 0
1 1
1 6
1 2
1 7
1 3
1 8
1 4
1 9
1
2
3
4
5
4
To select another track during random play
RANDOM
5
DISC
REPEAT
TRACK NO.
SINGLE
TL
1
2
3
4
5
4
0 5 0:1 2
÷Each time a track ends, the same operation as above is repeated, and
the track selected next is played.
÷Random play stops after all of the tunes have been played once.
÷The random playback can also be repeated by pressing the REPEAT
key.
To select another track in the middle of play-
ing one
To cancel random playback
RANDOM
¢
÷Pressing the 4key once returns to the beginning of the track being
played.
÷Press the RANDOM key to start normal playback.
Repeated playback
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Preparation
÷Load a disc in the CD player.
18
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
To repeat only the programmed tracks
CD-206/ DPF-R6010
Pre s s s o t h a t t h e “ PGM” in d ica t o r
1
lights.
P.MODE
PGM01 DISC?
CD-204/ 203/ DPF-R4010/ R3010
Select the disc.
2
PGM indicator light up.
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
PGM
1
2
3
4
5
Go to step 3within 8 seconds.
Select the desired track num ber.
3
÷All of the programmed tracks will be repeated.
÷In case only one track is programmed, only that track will be repeated.
÷Up to 32 tracks can be programmed. When “FULL” is displayed, no
more tracks can be programmed.
Main unit
Remote control unit
1
2
3
4
¢
4
7
5
8
0
6
9
+1 0
Go to step 4within 8 seconds.
Set the entry.
4
P.MODE
Repeat steps 2 – 4 above.
5
6
Press the REPEAT key.
CD-206/ DPF-R6010
REPEAT
REPEAT ON
CD-204/ 203/ DPF-R4010/ R3010
For the CD-206/ DPF-R6010
The current status is displayed when the key
is pressed once.
REPEAT indicator light up.
When it is pressed while the status is dis-
played, the repeat ONstatus can be set to OFF
(or vice versa).
PGM
DISC
NO.
REPEAT
TRACK NO.
1
2
3
4
5
3
0 1
Start playback.
7
6
Repeated playback
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
To repeat one of the discs (CD-204/203/DPF-R4010/R3010 only)
19
Pre s s s o t h a t t h e “ PGM” in d ica t o r
1
PGM indicator light up.
lights.
P.MODE
PGM
1
2
3
4
5
Select the disc.
2
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Press the P.MODE key.
3
4
P.MODE
Press the REPEAT key.
REPEAT indicator light up.
REPEAT
PGM
DISC
NO.
REPEAT
TRACK NO.
1
2
3
4
5
3
0 1
Start playback.
5
6
To repeat the entire disc
This allow s repeated playback of all the tracks on the disc
loaded in the disc tray.
CD-206/ DPF-R6010
Pre s s s o t h a t t h e “ PGM” in d ica t o r
goes off.
1
\
PGM01
01
P.MODE
CD-204/ 203/ DPF-R4010/ R3010
PGM indicator goes off.
PGM
Press the REPEAT key.
2
1
2
3
4
5
REPEAT
CD-206/ DPF-R6010
REPEAT ON
For the CD-206/ DPF-R6010
The current status is displayed when the key
is pressed once.
CD-204/ 203/ DPF-R4010/ R3010
When it is pressed while the status is dis-
played, the repeat ON status can be set to
OFF (or vice versa).
REPEAT indicator light up.
PGM
DISC
NO.
REPEAT
TRACK NO.
Start playback.
3
1
2
3
4
5
3
0 1
6
To cancel repeated playback
CD-206/ DPF-R6010
Press the REPEAT key.
REPEAT
REPEAT OFF
CD-204/ 203/ DPF-R4010/ R3010
REPEAT indicator goes off.
For the CD206/ DPF-R6010
PGM
DISC
REPEAT
TRACK NO.
Pre s s t h e REPEAT ke y o n ce a g a in .
(REPEAT ON \OFF)
1
2
3
4
5
3
0 1
Editing
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
The follow ing procedure allow s to record a CD w ithin the
specified tape length so that no m usic is interrupted in the
20 m iddle at the ends of sides A and B.
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
Norm al EDIT: Edit from one disc.
MULTI EDIT: Edit and record from several discs.
Preparation
÷Load a disc in the CD player.
REMOTE CONTROL UNIT
RC-P0 6 0 1
÷Check that the unit is in the normal play
TRACK mode.
!
: Keys and controls used in the operations described on this page.
Normal EDIT
1Light the “EDIT” indicator.
Blinks.
CD-206/ DPF-R6010
Do this operation in the stop m ode.
EDIT
EDIT DISC?
CD-204/ 203/ DPF-R4010/ R3010
Go to step 2 within 8 seconds.
If more than 8 seconds have elapsed,
press the key again.
Light up.
EDIT
PGM
1
2
3
4
5
2Select the disc.
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Go to step 3 within 8 seconds.
3Enter the recording time of the tape.
Press the num eric keys as show n below .
30-m inute tape : 000)
46-m inute tape : 00006
When using the num eric keys:
CD-206/ DPF-R6010
Main unit
Remote control unit
4
¢
1
2
3
EDIT DISC3 C-46
4
7
5
8
0
6
9
CD-204/ 203/ DPF-R4010/ R3010
Blinks.
«
1
6
2
7
3
8
4
9
5
+1 0
1 0
EDIT
C _ 4 6
÷The interval length can be adjusted with the skip keys 4and ¢in
units of one minute (to a maximum of 99 minutes).
÷If you commit a mistake in time entry, press the P.MODE key and
restart the procedure from the beginning.
When using the TIME DISPLAY key:
CD-206/ DPF-R6010
÷By pressing the TIME DISPLAY key the set time-length intervals will
change in this order:
"4 6 =5 4 =6 0 =7 4 =9 0 =? ?
"
Select the tim e.
Set the entry.
1
2
EDIT
TIME DISP.
CD-204/ 203/ DPF-R4010/ R3010
\
÷By pressing the TIME DISPLAY key the set time-length intervals will
change in this order: "4 6 =5 4 =6 0 =9 0 = - - "
÷Automatic editing is executed for side A and side B,
Editing
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Several CDs can be edited and recorded on 1 tape.
Choose songs from each disc, and edit/ record w hile con-
firm ing the rem aining tim e on files A and B, respectively.
21
Hereafter the illustration of the com m on parts
on the front panel is of CD-206/ DPF-R6010.
REMOTE CONTROL UNIT
RC-P0 6 0 1
: Keys and controls used in the operations described on this page.
(Except for CD-206/DPF-R6010)
MULTI EDIT
1 Press so that the "MULTI EDIT " indicator light.
Light up.
Do this operation in the stop m ode.
EDIT
MULTI
EDIT
PGM
1
2
3
4
5
Press tw ice
2Enter the recording time of the tape.)
3Select the desired track.
Select the disc (one disc only).
1
DISC 1
DISC 2
DISC 3
DISC 4
DISC 5
Select the tracks to be recorded.
2
Main unit
Remote control unit
÷If you made a mistake, press the CLEAR key and select the correct
track.
1
2
3
4
¢
÷The time remaining on side A or side B is indicated on the display.
÷When the time left on side A is less than the play time of the selected
song, that song will be programmed on side B.
÷If “FULL” is displayed, no further programming can be accepted.
4
7
5
8
0
6
9
«
P.MODE
+1 0
4Start recording.
When recording w ith a cassette deck equipped w ith CCRS
function:
÷With the CCRS function, the recording starts after about 1 minute.
÷If you have a cassette deck capable of Double-speed recording, use
Normal-speed recording.
Press the CCRS key (Cassette deck).
When recording w ith a norm al cassette deck:
Adjust the recording levels.
1
2 Press the record key.
Play the CD.
3
5 Repeat step 3,4 above.
÷Change discs and, if the “b-01” indication is given when you first select
a song, turn the tape to the start of side B.
Editing
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
To check the edited contents
22
CD-206/ DPF-R6010
CD-206/ DPF-R6010
EDIT A 01
CHECK
÷When the CHECK key is pressed, track numbers and remaining time in
the file A are displayed first, then those in the file B.
REMOTE CONTROL UNIT
RC-P
0
6
0
1
CD-204/ 203/ DPF-R4010/ R3010
CD-204/ 203/ DPF-R4010/ R3010
P.C. indicator light up.
CHECK
P.C.
5
DISC
NO.
TRACK NO.
4
A F I L E
During norm al EDIT:
÷When the CHECK key is pressed, the track Nos. of edited songs will
automatically be displayed in the order they are edited.
During MULTI EDIT:
÷Every time the CHECK key is pressed, the track Nos. are displayed in
the edited order.
Playing or recording the edited contents
When recording the edited content onto a tape, it is recom m ended
to use the synchro recording or CCRS recording function of
KENWOOD cassette decks.
6
÷Do not adjust the output level from this unit particularly during record-
ing.
÷For details, see the instruction manual of the cassette deck.
Press the 6 key to start playback according to the edited
content. The playback pauses at the beginning of the track
edited for tape side B. Press the 6 key again to continue
playback.
NNoottee
To clear the edited contents
During Norm al EDIT:
Press any one of these keys.
P.MODE
Main unit
Remote control unit
(CD-206/DPF-R6010 only)
CLEAR
CLEAR
0
÷ The edited data is cleared entirely.
Do this operation in the stop m ode.
During MULTI EDIT:
P.MODE
1. While you can edit with a different time setting to that of the tape you are using, part of the tape may be left with nothing recorded on it, or the
last track on side A or side B may be cut short.
2. The EDIT function may not operate properly for discs having only one track or having tracks of long duration such as classical music.
NNootteess
Timer operations
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
Tim er playback of CD can be started at any tim e using an
audio tim er w hich is available in audio stores.
This unit
23
System control cord
Audio cord
Preparation
÷ Connect the power cords of the associated
components so that their power can be
turned ON through the audio timer.
(Also, be sure to read carefully the instruc-
tion manual of the timer.)
Amplifier
12 : 00
To wall AC outlet
Audio timer
Turn the powers of the associated components
ON.
÷If the amplifier is not connected to the CD player through a system
control cord, select the "CD" input with the input selector.
1
2Preparation
Load a disc in the CD player.
9
Label side
3Set the amplifier volume.
Play the disc.
1
6
Adjusting the volum e:
Set the volum e the m axim um (0 dB) using the OUTPUT
(UP) key on the rem ote control unit (Except CD-203/ DPF-
Adjust the am plifier volum e.
2
3
NNoottee
(Use the rem ote control unit (Except CD-
203/ DPF-R3010) of this unit to adjust the
volum e to the m axim um level.)
R3010) , and adjust the volum e to the desired level on the
am plifier side.
(Since the sound output is at the maximum level when the power
is turned on, lowering the level with the remote control unit will
change the volume.)
Stop the disc.
7
4Set the timer ON time.
Set the tim er so that it supplies
pow er at the specified tim e.
÷With some audio timer models, the power is automatically turned OFF
when the timer ON time is set. With such a model, skip step 5 below.
Turn OFF the power output from the audio
timer.
5
÷Do not touch the ON/ STANDBY (POWER/
amplifier and CD player.
) switches of the
÷When the set time comes, the disc playback starts automatically.
1. Some amplifiers cannot be used with a timer. Before using a amplifier, check it.
2. When operating the unit other than CD player using an audio timer, be sure to remove the disc from the CD player.
NNootteess
Maintenance
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
24
Disc handling precautions
Discs which can be played with this unit
CD (12 cm , 8 cm ) (CD-TEXT support), CDV (only the audio part)
÷With CD-G (CD Graphics) discs, this unit can play only the audio part.
Handling
Hold compact discs so that you do
not touch the playing surface.
Label side
Never play a cracked or warped disc.
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed disc or a disc
repaired with tape or adhesive agent.
Please do not use discs which are not round because they may cause a
malfunction.
÷Do not attach paper or tape to either
the playing side or the label side of
compact discs.
÷The paste left on the label surface
after a sticker has been peeled off is
a factor which may cause malfunc-
tion. If the surface is sticky due to
remaining paste, be sure to clean it
with alcohol before use.
Playing side
Sticker
Sticky paste
Cleaning
If fingerprints or foreign matter be-
come attached to the disc, lightly
wipe the disc with a soft cotton cloth
(or similar) from the center of the
disc outwards, in a radial manner.
CD accessories
The CD accessories (stabilizer, protection sheet, protection ring, etc.)
which are marketed for improving the sound quality or protecting discs as
well as the disc cleaner should not be used with this system because they
may cause malfunction.
Storage
When a disc is not to be played for a
long period of time, remove it from
the CD player and store it in its case.
Cleaning
Note related to transportation and move-
ment
Do not use volatile solvents such as alcohol, paint thinner, gasoline, or
benzine, etc. to clean the cabinet. Use a clean dry cloth.
Before transporting or m oving this unit, carry out the follow ing
operations.
Do not use contact cleaners because it could cause a malfunction. Be
specially careful against contact cleaners containing oil, for they may
deform the plastic components.
1. Turn the unit ON but do not load a disc.
2. Wait a few seconds and verify that the display show n appears.
CD-206/ DPF-R6010
Caution on condensation
NO DISC
CD-204/ 203/ DPF-R4010/ R3010
Condensation (of dew) may occur inside the unit when there is a great
difference in temperature between this unit and the outside.
This unit may not function properly if condensation occurs. In this
case, leave the unit for a few hours with the power left ON, and restart
the operation after the condensation has dried up.
1
2
3
4
5
6
7
8
9
1 0
1 5
2 0
1 1
1 6
1 2
1 7
1 3
1 8
1 4
1 9
1
2
3
4
5
n o d I S C
Be specially cautious against condensation in a follow ing
circum stance:
3. Press the 0OPEN/ CLOSEkey to open the disc tray com pletely.
4. Press the 0OPEN/ CLOSE key again to close the tray.
5. Wait a few seconds and set the unit to STANDBY m ode.
When this unit is carried from a place to another across a large
difference in temperature, when the humidity in the room where this
unit is installed increases, etc.
In case of difficulty
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
What appears to be a m alfunction m ay not alw ays be serious. If your unit should not perform as expected, consult the table
below to see if the problem can be corrected before seeking help from your dealer or service representative.
25
Operation to reset
The m icrocom puter m ay m alfunction (im possibility to operate,
Unplug the pow er cord from the pow er socket and plug the
pow er cord into the socket again.
erroneous display, etc.) w hen the connection cords are un-
plugged w hile the unit is ON or due to an external factor. In this
case, execute the follow ing m ethod to reset the m icrocom puter
and return it to norm al condition.
÷Please be aware that resetting the CD player will erase all stored
information and return it to the factory settings.
CD player unit
Sym ptom
Cause
Rem edy
The unit is not turned ON w ith the ON/
÷Power plug is loosely connected.
÷Insert the power plug firmly to the AC outlet.
STANDBY (POWER/
) sw itch ON.
÷With the powerplug connected to the switched ÷Turn the amplifier’s power ON.
AC outlet of an amplifier, the power of the
amplifier is turned off.
There is no sound even w hen a disc is loaded.
÷Disc is loaded upside down.
÷Disc is loose.
÷Load the disc again with its label side up.
÷Insert disc properly.
÷Disc is dirty.
÷Wipe off the dust on the surface of the disc
referring to “Disc handling precautions”.¢
÷Replace the disc with a new one.
÷Disc is cracked.
÷Condensation has occurred on the optical lens
÷Remove any condensation from the unit by
referring to the section entitled, “Caution on
unit.
condensation”.
¢
÷Play mode is not entered.
÷The connection cords are inserted loosely.
÷Output level is attenuated too low.
÷Press the 6 key.
÷Connect all connection cords firmly.
÷Adjust the output level with OUTPUT key on
the remote control unit.
5
Music is interrupted. (Sound is skipped.)
÷Disc is too dirty.
÷Wipe off the dust on the disc surface referring
to “Disc handling precautions”.
¢
÷Disc is cracked.
÷Oscillation is applied to this unit.
÷Replace the disc with a new one.
÷Tryselecting a place where no strong vibrations
occur by changing the installation place, etc.
Play begins as soon as the unit is turned ON.
÷This unit is designed so that play begins auto- ÷If automatic play is not required remove the
matically when the unit is turned ON if a disc is
already loaded.
disc from the player before setting the unit to
STANDBY mode.
Remote control unit
Sym ptom
Cause
Rem edy
Rem ote control operation is not possible.
÷Batteries are exhausted.
÷Replace with new batteries.
÷Operate the remote control unit within the
controllable range.
8
÷The remote control unit is too far away from the
main system, controlling angle is too large, or
there is an obstacle in between.
8
For the U.S.A.
CAUTION:
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO, HACHIOJI-SHI,
TOKYO, JAPAN
Use of controls or adjustment or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS NO. 21
In compliance with Federal Regulations, following are reproductions of
labels on, or inside the product relating to laser product safety.
CFR 1040.10, CHAPTER
I, SUBCHAPTER J.
Location: Back Panel
Specifications
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
CD-206/ DPF-R6010
CD-204/ 203/ DPF-R4010/ 3010
26
[ Form at ]
[ Form at ]
System .......................... Com pact disc digital audio system
Laser ...................................................... Sem iconductor laser
System .......................... Com pact disc digital audio system
Laser ...................................................... Sem iconductor laser
[ D/ A Convertors ]
[ D/ A Convertors ]
D/ A Conversion ........................................... 1 Bit (D.R.I.V.E.)
Oversam pling ................................................. 8 fs (352.8 kHz)
D/ A Conversion ............................................................... 1 Bit
Oversam pling ................................................. 8 fs (352.8 kHz)
[ Audio ]
[ Audio ]
Frequency response .......................... 4 Hz – 20 kHz, ±0.5 dB
Signal to noise ratio ................................. More than 100 dB
Dynam ic range ............................................ More than 95 dB
Total harm onic distortion + noise
Frequency response .......................... 4 Hz – 20 kHz, ±0.5 dB
Signal to noise ratio ................................... More than 95 dB
Dynam ic range ............................................ More than 95 dB
Total harm onic distortion + noise
.............................................. Less than 0.005% (at 1 kHz)
Wow & flutter ....................................... Unm easurable Lim it
Output level/ im pedance
............................................. Less than 0.008% (at 1 kHz)
Wow & flutter ....................................... Unm easurable Lim it
Output level/ im pedance
Variable ............................................... (Max.) 2 V/ 0.3 kΩ
Digital output
Fixed (CD-203/ DPF-R3010) ............................. 2 V/ 0.8 kΩ
Variable (CD-204/ DPF-R4010) ............. (Max.) 2 V/ 0.3 kΩ
Headphone output (Max.)
Coaxial .................................................... 0.5 V p-p / 75 Ω
Optical ........................................... –15 dBm – –21 dBm
(Wave length 660 nm )
(CD-204/ DPF-R4010 only) ........................... 20 m W (32 Ω)
Headphone output (Max.) .............................. 20 m W (32 Ω)
[ General ]
[ General ]
Pow er consum ption ....................................................... 13 W
Dim ensions ......................................... W : 440 m m (17-5/ 16")
H : 125 m m (4-15/ 16")
Pow er consum ption ....................................................... 14 W
Dim ensions ......................................... W : 440 m m (17-5/ 16")
H : 125 m m (4-15/ 16")
D : 397 m m (15-5/ 8")
D : 397 m m (15-5/ 8")
Weight (Net) .................................................... 5.0 kg (11.0 lb)
Weight (Net) .................................................... 5.0 kg (11.0 lb)
1. KENWOOD follows a policy of continuous advancements in development. For this reason specifications may be changed without notice.
2. The full performance may not be exhibited in an extremely cold location (under a water-freezing temperature).
NNootteess
For the U.S.A.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to
radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver in connected.
– Consult the dealer or an experienced radio/TV technician for help.
CD-2 0 6 / 2 0 4 / 2 0 3 / DPF-R6 0 1 0 / R4 0 1 0 / R3 0 1 0 (En)
27
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below. Refer
to the model and serial numbers whenever you call upon your dealer for
information or service on this product.
Model
Serial Number
|